ML18142A111: Difference between revisions
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
StriderTol (talk | contribs) (StriderTol Bot change) |
||
(3 intermediate revisions by the same user not shown) | |||
Line 3: | Line 3: | ||
| issue date = 05/28/1981 | | issue date = 05/28/1981 | ||
| title = Rev a to Acceptance Test Procedure ATP449, PC202-Q2 Buffer Amplifier. | | title = Rev a to Acceptance Test Procedure ATP449, PC202-Q2 Buffer Amplifier. | ||
| author name = | | author name = Kamerman L | ||
| author affiliation = VALIDYNE ENGINEERING SALES CORP. | | author affiliation = VALIDYNE ENGINEERING SALES CORP. | ||
| addressee name = | | addressee name = | ||
Line 17: | Line 17: | ||
=Text= | =Text= | ||
{{#Wiki_filter:AlidyNE ENGINEERING CORPOIIATION REVISIONS LTR ECO DESCRIPTION DATE APPROVED A See DCN 5 28 81 ...... ~. ----1 ( .. ~i~1 iB8ia 7 0~6M:>i!~ \ | {{#Wiki_filter:AlidyNE ENGINEERING CORPOIIATION REVISIONS LTR ECO DESCRIPTION DATE APPROVED A See DCN 5 28 81 ......~. | ||
----1 | |||
* NORTHRIDGE. | ( .. ~i~ 1 iB8ia F | ||
CA 91324 * (213) 886-8488 | 7 0 ~6M:>i!~ \ | ||
* Telex No. 65-1303 VEC 304-11/80 AlidyNE l!NGIN ** IIINCI COlll"OIIATlON 1.0 SCOPE This document defines the Acceptance Test Procedure (ATP) for the PC202-Q2 Potentiometric Signal Conditioner. | SIGNATURE TITLE PC202-Q2 Buffer Amplifier PROD TEST NGINEERING | ||
The ATP performs functional checks of all operating characteristics. | :....-------,,:;.,~-=...:::~----:.......:._ _ _ _..,_______-f NUMBER REV QUAL CONTROL ATP449 A SHEET 1 OF 13 8626 WILBUR AVENUE | ||
A sample of the Test Report to be used with this ATP is contained in Appendix A. 2.0 EQUIPMENT REQUIRED Table 1 lists the test equipment required to perform the ATP. Table 1. Equipment Required for ATP Part No. Description Manufacturer or Model | * NORTHRIDGE. CA 91324 * (213) 886-8488 | ||
* Alternate MCl (Test) Validyne --None Extender Card (MC1-MC170) | * Telex No. 65-1303 VEC 304-11/80 | ||
Validyne --None BA Test Cable | |||
-Equivalent Function Generator | AlidyNE l!NGIN **IIINCI COlll"OIIATlON 1.0 SCOPE This document defines the Acceptance Test Procedure (ATP) for the PC202-Q2 Potentiometric Signal Conditioner. The ATP performs functional checks of all operating characteristics. A sample of the Test Report to be used with this ATP is contained in Appendix A. | ||
* Exact 100 Commercial Equivalent Frequency Counter Hewlett Packard 5314A Commercial Equivalent 3.0 PRELIMINARY PROCEDURE 3.1 Plug extender card into front panel connector on MC!. 3.2 Refer to figure 1 and set switches and controls on PC202-Q2 as follows: Switch or Control SPAN (R24) GAIN (S4) FILTER (S2) DC/AC (S3) IN/OUT (SlA) -SV/0 (SlB) DIFF/SINGLE ENDED (SlC) | 2.0 EQUIPMENT REQUIRED Table 1 lists the test equipment required to perform the ATP. | ||
3.4 Refer to figure 1 for location, and visually check that resistors R8 and* R12 are each 1 Megohm, 5%. NUMBER ATP449 SHEET 2 OF 13 | Table 1. Equipment Required for ATP Part No. | ||
Description Manufacturer or Model | |||
* Alternate MCl (Test) Validyne -- None Extender Card (MC1-MC170) Validyne -- None BA Test Cable DC Source Validyne Validyne TE-124 None None Digital Multimeter (DMM) (2) Data Precision 245 Commercial Equivalent Oscilloscope B & K 1470 Commercial | |||
.... | - Equivalent Function Generator | ||
* Exact 100 Commercial Equivalent Frequency Counter Hewlett Packard 5314A Commercial Equivalent 3.0 PRELIMINARY PROCEDURE 3.1 Plug extender card into front panel connector on MC!. | |||
3.2 Refer to figure 1 and set switches and controls on PC202-Q2 as follows: | |||
Switch or Control Setting SPAN (R24) Full CW GAIN (S4) Xl FILTER (S2) 200 DC/AC (S3) DC IN/OUT (SlA) OUT | |||
-SV/0 (SlB) -sv DIFF/SINGLE ENDED (SlC) DIFF 3.3 Plug PC202-Q2 into extender card cable connector. | |||
[ill] [ill]lM *-rnrif&-e | 3.4 Refer to figure 1 for location, and visually check that resistors R8 and* | ||
[illlM | R12 are each 1 Megohm, 5%. | ||
NUMBER REV ATP449 A SHEET 2 OF 13 | |||
AlidyNE ENGINl&l!IIING COIIPOIIAT10N 3.5 If necessary, connect MCl to 115 Vac and press MCl power switch; observe that power-on indicator lights. 4.0 INITIAL TEST SETUP 4.1 Connect DMM to PC202-Q2 as shown in figure 2. MCI(TEST) | |||
EXTENDER | AlidyNE l!-INalllll- co11..a11ATION Appendix A 11 11 Sample Test Report NUMBER ATP455 SHEET 1 OF l | ||
NUMBER ATP449 SHEET 4 OF 13 | |||
ATED TERMINAL | |||
5.2 Common Mode Adjustment 5.2.1 On connector of PC202-Q2 (figure 1), jumper together pins 20 and 22 and connect to de source and DMM as shown in. figure 3. | ( TYP 7 PLACES) | ||
5.2.3 Adjust CM ADJ potentiometer R18 for 0.000(+/-0.002)V DC output on DMM. 5.2.4 Set polarity switch of de source to minus(-); | Cl 1110 | ||
output on DMM should be 0.000(+/-0.005)V DC. 5.2.5 Repeat steps 5.2.2 thru 5.2.4, if necessary. | @ R50 IZERO CONTROL 499K CfilI] | ||
5.2.6 Remove jumper'from pins 20 and 22 and disconnect de source and DMM . from PC202-Q2. | 12.lK .+15V | ||
....z ;;;Cl w | |||
z ex: | |||
e-QD: | |||
I | |||
!PAN 0 w | |||
@ @ R24 SPAN. | |||
24.9K1 | |||
~lff<[1]-e *-15V 0.. | |||
0 Cl | |||
..J 0 | |||
[ill] u Vl | |||
~ | |||
GAIN [ill]lM CAL R4 Ill II *-rnrif&-e [illlM BAL 2 4 | |||
1 3 | |||
,~----: :1 D S4 1~-1 IMIN IN -5V DIFF 6 | |||
8 5 | |||
7 n 10 9 111111 12 11 Ill C I"u" ZERO I | |||
SINGLE 14 16 13 15 | |||
---u I ~ HI S2 \ | |||
OUT 0 ENDED | |||
' 18 17 EJ 45 20 19 | |||
'&" 22 21 i | |||
DC CM , 24 23 DC/AC AC ADJ ',, 26 25 28 27 0 +11 TP2 \ 30 29 | |||
~ | |||
r----, | |||
0 -11 TPl I R11 I | |||
@ 56.2K I I 0 out TP3 1& | |||
L ___ .JI rem BAL m ii I-* | |||
NOTE: | |||
& ONLY ONE BAL POT IS IHSTALLED ON THE BOARD, AND IT IS NORMALLY RlS; SOME UNITS MAY HAVE Rll INSTALLED INSTEAD OF Rl 5 i Q. | |||
8- | |||
:z: | |||
-~i~z C: | |||
3: | |||
m m :I. | |||
:a i "' | |||
en | |||
:x m | |||
!!I C) | |||
:a m | |||
Figure 1. PC202-Q2 Parts Locations L____ | |||
AlidyNE ENGINl&l!IIING COIIPOIIAT10N 3.5 If necessary, connect MCl to 115 Vac and press MCl power switch; observe that power-on indicator lights. | |||
4.0 INITIAL TEST SETUP 4.1 Connect DMM to PC202-Q2 as shown in figure 2. | |||
MCI(TEST) | |||
EXTENDER PC202-Q2 CARD | |||
& JUNCTION U4-6 &Rl9 SIG GND 24 HI DMM NOTES: | |||
: 1. BOXED CALLOUT jxxxl INDICATES PANEL OR BOARD MARKINGS | |||
& SEE FIGURE l FOR LOCATIONS Figure 2. Initial Test Setup NOTE: Unless otherwise indicated, all switches, controls, potentiometers, and test points referred to in the ATP procedures that follow are located on the PC202-Q2; see figure 1 for locations. | |||
NUMBER REV ATP449 A SHEET 4 OF 13 | |||
AlidyNE l!NGINEl!III- COIIPOIIATION | |||
( | |||
5.0 FUNCTIONAL TESTS Perform all tests and in the order given~ | |||
5.1 Null Adjustment 5.1.1 On connector of PC202-Q2 (figure 1), jumper pins 20 and 22 together and connect to signal ground (pin 24). | |||
NOTE BAL potentiometer Rll may be installed on some units instead of R15. On these units, adjust Rll in step 5.1.2. | |||
5.1.2 Adjust BAL potentiometer Rl5 for 0.000(+/-0.002)V DC output on DMM. | |||
5.1.3 Remove the ground from pins 20 and 22 of connector. | |||
5.2 Common Mode Adjustment 5.2.1 On connector of PC202-Q2 (figure 1), jumper together pins 20 and 22 and connect to de source and DMM as shown in. figure 3. | |||
5.2.2 Set polarity switch of de source to plus(+) and output to +10.000(+/-0.005)V. | |||
5.2.3 Adjust CM ADJ potentiometer R18 for 0.000(+/-0.002)V DC output on DMM. | |||
5.2.4 Set polarity switch of de source to minus(-); output on DMM should be 0.000(+/-0.005)V DC. | |||
5.2.5 Repeat steps 5.2.2 thru 5.2.4, if necessary. | |||
5.2.6 Remove jumper'from pins 20 and 22 and disconnect de source and DMM | |||
. from PC202-Q2. | |||
NOTE Any change in the value of RlOl (open circuit to 24.9K range) requires that paragraphs 5.1 and 5.2 be performed. | NOTE Any change in the value of RlOl (open circuit to 24.9K range) requires that paragraphs 5.1 and 5.2 be performed. | ||
5.3 Linearity, Symmetry, and Noise 5.3.1 Using the BA test cable, connect de source and DMM to input connector on*rear panel of MCl as shown in figure 4. 5.3.2 Connect DMM to OUTPUT A of MCl as shown in figure 4 .* 5.3.3 Set output of de source to 0.0000(+/-0.0005)V DC. 5.3.4 Adjust ZERO potentiometer R44 for 0.000(+/-0.002)V DC output on DMM. | 5.3 Linearity, Symmetry, and Noise 5.3.1 Using the BA test cable, connect de source and DMM to input connector on*rear panel of MCl as shown in figure 4. | ||
EXTENDER | 5.3.2 Connect DMM to OUTPUT A of MCl as shown in figure 4.* | ||
!DC OUTPUT! BA TEST EXTENDER CABLE CARD RED BLACK I OUTPUT | 5.3.3 Set output of de source to 0.0000(+/-0.0005)V DC. NUMBER REV ATP449 A 5.3.4 Adjust ZERO potentiometer R44 for 0.000(+/-0.002)V DC output on DMM. SHEET 5 OF 13 | ||
\A/11 "0110 A.\/C'P.,111C' a l\lr"IOTUClr"'\re f'"A n .. ..,.., ... , -, ....... , .... ,.,,.. ,., .. ,.,,, -T | |||
AlidyNE ENGINEEIII- COll"'IIATION MCI(TEST) | |||
5.3.6 Adjust SPAN control R24 for +10.000(+/-0.00S)V output on DMM. 5.3.7 Set DMM to read ACmV; the noise indication on the DMM should be less than or equal to 10 mV AC. Indicate acceptance on test report with checkmark. | - EXTENDER CARD r - ffi U4-6 PC202-Q2 JUNCTION SIG GND | ||
-INPUT 24 - C) | |||
- +INPUT | |||
-- 224 20 Rl9 | |||
\ \I \ | |||
!COM | |||
) | |||
I HI | |||
) RED | |||
'I J IDC OUTPUT! | |||
¥ BLK ~.) .:> HI DMM DC SOURCE Dr,tH NOTES: | |||
: 1. BOXED CALLOUT lxxxl INDICATES PANEL OR BOARd MARKINGS | |||
~ SEE FIGURE 1 FOR LOCATIONS Figure 3. Com:mon Mode ~djustment Test Setup DC SOURCE MCI(TEST) | |||
!DC OUTPUT! BA TEST EXTENDER PC202-Q2 CABLE CARD RED BLACK I OUTPUT AI RED HI HI DMM NOTES: | |||
: 1. BOXED C~LLOUT jxxxj INDICATES PANEL OR BOARD MARKINGS | |||
: 2. SEE FIGURE 1 FOR LOCATION Figure 4. Linearity and Symmetry Test Setup NUMBER REV ATP449 A* | |||
SHEET 6 OF 13 | |||
~~-""~..,~ \A/11 "0110 A.\/C'P.,111C' a l\lr"IOTUClr"'\re f'"A n .. ..,.., ... , - , ....... , .... ,.,,.. ,., .. ,.,,, - T .. | |||
AlidyNE ENQIN. . .IINQ co11..allATION | |||
( | |||
5.3.5 Set output of de source to +10.000(+/-0.00Z)V. | |||
5.3.6 Adjust SPAN control R24 for +10.000(+/-0.00S)V output on DMM. | |||
5.3.7 Set DMM to read ACmV; the noise indication on the DMM should be less than or equal to 10 mV AC. Indicate acceptance on test report with checkmark. | |||
5.3.8 Perform the steps in table 2 to check linearity and symmetry of PC202-Q2. | 5.3.8 Perform the steps in table 2 to check linearity and symmetry of PC202-Q2. | ||
For steps 1 thru 5, set POLARITY switch of de source to plus(+) and input as indicated; for steps 6 thru 10, set POLARITY switch of de source to minus(-) and input as indicated. | For steps 1 thru 5, set POLARITY switch of de source to plus(+) and input as indicated; for steps 6 thru 10, set POLARITY switch of de source to minus(-) and input as indicated. Indicate acceptance on test report with checkmark. | ||
Indicate acceptance on test report with checkmark. | Table 2. Linearity and Symmetry Check DC Source Output Specification Step Input (VDC) On DMM (VDC) 1 +10.000 +10.000+/-0.005 2 + 7.500 + 7.5QQ+/-Oa007 3 + 5.000 + 5.000+/-0.007 4 + 2.500 + 2.500+/-0.007 5 + 0.000 0.000::to.002 6 | ||
Table 2. Linearity and Symmetry Check DC Source Output Specification Step Input (VDC) On DMM (VDC) 1 +10.000 +10.000+/-0.005 2 + 7.500 + 7.5QQ+/-Oa007 3 + 5.000 + 5.000+/-0.007 4 + 2.500 + 2.500+/-0.007 5 + 0.000 0.000::to.002 6 -0.000 -0.000+/-0.002 | 7 | ||
.. 007 5.4 Gain 5.4.1 Set POLARITY switch of de source to plus(+). 5.4.2 Perform the steps in table 3 to check gain of PC202-Q2; for each step, set GAIN switch S4 and input from the de source as indicated. | - 0.000 - | ||
Indicate acceptance on test report with checkmark. | 0.000+/-0.002 | ||
Table 3. Gain Check Gain Switch DC Source Output Specification Step S4 Input (VDC) On DMM (VDC) 1 X1 +10.000 +10.000+/-0.005 2 X2.5 + 4.000 +10.000+/-0.300 3 XS + 2 .. 000 +10.000+/-0.300 4 XlO + 1.000 +10.000+/-0.300 5 X25 + 0.400 +10.000+/-0.300 NUMBER ATP449 SHEET 7 OF 13 | - 2.500 - 2.SOO+/-Oa0,07 8 - 5.000 - 5.000+/-0.007 9 - 7a500 - 7.500+/-0.007 10 -10.000 -10.000+/-0 .. 007 5.4 Gain 5.4.1 Set POLARITY switch of de source to plus(+). | ||
5.4.2 Perform the steps in table 3 to check gain of PC202-Q2; for each step, set GAIN switch S4 and input from the de source as indicated. Indicate acceptance on test report with checkmark. | |||
Indicate acceptance on test report with checkmark. | Table 3. Gain Check Gain Switch DC Source Output Specification Step S4 Input (VDC) On DMM (VDC) 1 X1 +10.000 +10.000+/-0.005 2 X2.5 + 4.000 +10.000+/-0.300 3 XS + 2 .. 000 +10.000+/-0.300 4 XlO + 1.000 +10.000+/-0.300 5 X25 + 0.400 +10.000+/-0.300 NUMBER REV ATP449 A SHEET 7 OF 13 | ||
5.5.3 Adjust ZERO CONTROL R50 maximum clockwise (CW); output on DMM should be +11.000(+/-1.000)V. | |||
Indicate acceptance on test report with checkmark. | A(idyNE l!NQIN **IIINQ COlll"OIIArtON | ||
5.5.4 Set IN/OUT switch SlA to OUT. 5.5.5 Remove jumper and ground from pins 20 and 22 of connector. | ( | ||
5.6 Single Ended Input 5.6.1 Set DIFF/SINGLE ENDED switch SlC to SINGLE ENDED. 5.6.2 Reconnect BA test cable to MCl; -ensure GAIN switch S4 is set to Xl. 5.6.3 Connect negative terminal (black) of de source to signal ground (pin 24) on the PC202-Q2 connector; set de source output to 0.0000(+/-0.0002)V. | 5.4.3 Disconnect BA test cable from MCl. | ||
The output on DMM at OUTPUT A of MCl should be 0.000(+/-0.005)V DC. Indicate acceptance on test report with checkmark. | 5.5 Zero 5.5.1 Set GAIN switch S4 to Xl and IN/OUT switch SlA to IN; on connector of PC202-Q2 (figure 1), jumper pins 20 and 22 together and connect to signal ground (pin 24). | ||
5.6.4 Set output of de source to +10.000(+/-0.005)V; the output on DMM at OUTPUT A of MCl should be +10.000(+/-0.0lO)V. | 5.5.2 Adjust ZERO CONTROL R50 maximum counterclockwise (CCW); output on DMM should be -11.000(+/-1.000)V. Indicate acceptance on test report with checkmark. | ||
Indicate acceptance on test report with checkmark. | 5.5.3 Adjust ZERO CONTROL R50 maximum clockwise (CW); output on DMM should be | ||
5.7 Calibration Circuit 5.7.1 Disconnect BA test cable from de source and DMM. 5.7.2 On connector of PC202-Q2 (figure 1), connect pin 28 to signal ground (pin 24). 5.7.3 If resistor R3 (figure 1) is connected to +15V, adjust CAL potentiometer R4 for +10.000(+/-0.lOO)V output on DMM; if R3 is connected to -15V, adjust R4 for -10.000(+/-0.lOO)V on DMM. 5.7.4 Adjust CAL potentiometer R4 full CCW; the output indication on DMM should be 0.000(+/-0.lOO)V. | +11.000(+/-1.000)V. Indicate acceptance on test report with checkmark. | ||
Indicate acceptance on test report with checkmark. | 5.5.4 Set IN/OUT switch SlA to OUT. | ||
5.5.5 Remove jumper and ground from pins 20 and 22 of connector. | |||
5.6 Single Ended Input 5.6.1 Set DIFF/SINGLE ENDED switch SlC to SINGLE ENDED. | |||
5.6.2 Reconnect BA test cable to MCl; -ensure GAIN switch S4 is set to Xl. | |||
5.6.3 Connect negative terminal (black) of de source to signal ground (pin 24) on the PC202-Q2 connector; set de source output to 0.0000(+/-0.0002)V. The output on DMM at OUTPUT A of MCl should be 0.000(+/-0.005)V DC. Indicate acceptance on test report with checkmark. | |||
5.6.4 Set output of de source to +10.000(+/-0.005)V; the output on DMM at OUTPUT A of MCl should be +10.000(+/-0.0lO)V. Indicate acceptance on test report with checkmark. | |||
5.7 Calibration Circuit 5.7.1 Disconnect BA test cable from de source and DMM. | |||
5.7.2 On connector of PC202-Q2 (figure 1), connect pin 28 to signal ground (pin 24). | |||
5.7.3 If resistor R3 (figure 1) is connected to +15V, adjust CAL potentiometer R4 for +10.000(+/-0.lOO)V output on DMM; if R3 is connected to -15V, adjust R4 for -10.000(+/-0.lOO)V on DMM. | |||
5.7.4 Adjust CAL potentiometer R4 full CCW; the output indication on DMM should be 0.000(+/-0.lOO)V. Indicate acceptance on test report with checkmark. | |||
5.7.5 Remove ground from pin 28 of connector. | 5.7.5 Remove ground from pin 28 of connector. | ||
NUMBER ATP449 SHEET 8 OF 13 | NUMBER REV ATP449 A SHEET 8 OF 13 | ||
* I OUTPUT I | AlidyNE l!NGINl!ERING CORPORATION 5.8 Input Resistance 5.8.1 Press MCl power switch; observe that power-on indicator goes out. | ||
I OUTPUT A I BLACK RED | 5.8.2 Set DIFF/SINGLE ENDED switch SlC to DIFF; set DMM to read resistance on the 10 Megohm range. | ||
( | 5.8.3 Connect DMM between pin 22 of PC202-Q2 and Ul-5 (figure 1); the DMM indication should be between 0.95 and 1.30 Megohms. Indicate acceptance on test report with checkmark; disconnect DMM. | ||
Set PC202-Q2 switches as follows: Switch GAIN (S4) FILTER (S2) DC/AC (S3) IN/OUT (SlA) DIFF/SINGLE ENDED (SlC) 5.9.4 15 Hz Test | 5.8.4 Connect DMM between pin 20 and junction of R7 and Ul-12 (figure 1); the DMM indication should be between 0.95 and 1.30 Megohms. Indicate acceptance on test report with checkmark;*disconnect DMM. | ||
5.8.5 Press MCl power switch; observe that power-on indicator lights. | |||
5.9 Filter 5.9.1 Connect function generator, frequency counter, and oscilloscope, as shown in figure 5. | |||
FUNCTION MCl(TEST) | |||
.GENERATOR | |||
*I OUTPUT I EXTENDER CARD PC202-Q2 I OUTPUT A I BLACK RED BNC/BANANA PATCH CORD I INPUT I FREQUENCY @[TI COUNTER OSCILLOSCOPE NOTES: | |||
: 1. BOXED CALLOUT~- INDICATES PANEL OR BOARD MARKINGS Figure 5. Filter Test Setup | |||
( | |||
NUMBER REV ATP449 A | |||
SHEET 9 OF 13 | |||
AlidyNE | |||
( 1!-IN**IIINQ COIIPOIIATION 5.9.2 Set oscilloscope for lV/DIV display, external trigger, and DC coupling. | |||
5.9.3 Set PC202-Q2 switches as follows: | |||
Switch Setting GAIN (S4) no FILTER (S2) 15 HZ DC/AC (S3) AC IN/OUT (SlA) OUT DIFF/SINGLE ENDED (SlC) DIFF 5.9.4 15 Hz Test 5.9.4.1 Set function generator for a 1.5 Hz sinewave output, as indicated on the frequency counter; adjust output f~r a 7-division display on oscilloscope. | |||
5.9.4.2 Increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 15(+/-2)Hz. | 5.9.4.2 Increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 15(+/-2)Hz. | ||
Indicate acceptance on test report with checkmark. | Indicate acceptance on test report with checkmark. | ||
5.9.5 45 Hz Test 5.9.5.1 Set FILTER switch S2 to 45 HZ. 5.9.5.2 Increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 45(+/-7)Hz. | 5.9.5 45 Hz Test 5.9.5.1 Set FILTER switch S2 to 45 HZ. | ||
5.9.5.2 Increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 45(+/-7)Hz. | |||
Indicate acceptance on test report with checkmark. | Indicate acceptance on test report with checkmark. | ||
5.9.6 100.Hz Test 5.9.6.1 Set FILTER switch S2 to-100 HZ. 5.9.6.2 increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 100(+/-15)Hz. | 5.9.6 100.Hz Test 5.9.6.1 Set FILTER switch S2 to-100 HZ. | ||
Indicate acceptance on test report with checkmark. | 5.9.6.2 increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 100(+/-15)Hz. Indicate acceptance on test report with checkmark. | ||
5.9.7 200 Hz Test *5.9.7.1 Set FILTER switch S2 to 200 HZ. NUMBER ATP449 SHEET 10 OF 13 | 5.9.7 200 Hz Test | ||
*5.9.7.1 Set FILTER switch S2 to 200 HZ. | |||
Indicate acceptance on test report with checkmark. | NUMBER REV ATP449 A SHEET 10 OF 13 | ||
Disconnect oscilloscope and BA test cable from MCl. | |||
5.10.3 Using DMM, check that excitation at pin 18 (figure 1) is -5.000(+/-0.400)V; indicate acceptance on test report with checkmark. | A(idyNE ENGIN . .iRI- CORPORATION 5.9.7.2 Increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 200(+/-30)Hz. Indicate acceptance on test report with checkmark. | ||
5.10.4 Set -5V/O switch SIB to O. 5.10.5 Connect DMM COM lead to pin 18 and Hi lead to U7-7 (figure 1); the DMM indication should be -5.000(+/-0.400)V. | 5.9.7.3 Disconnect oscilloscope and BA test cable from MCl. | ||
Indicate acceptance on test report with checkmark. | 5.10 Excitation 5.10.1 Connect DMM COM lead to signal ground (pin 24) of PC202-Q2 (figure 1); | ||
5.10.6 Disconnect DMM from PC202-Q2. | set DMM to read DC. | ||
5.11 Current Consumption 5.11.1 Connect the DMM leads to the MCl +15V current and voltage test jacks (figure 6); set DMM to read DCmA. 5.11.2 Set the MCl +15V I TEST switch (figure 6) to +15; the DMM indication should not exceed 22 mA. Indicate acceptance on test report with checkmark. | 5.10.2 Using DMM, check that excitation at pin 16 (figure 1) is +5.000(+/-0.400)V; indicate acceptance on test report with checkmark. | ||
5.11.3 Set the MCl +15V I TEST switch to the unmarked position; disconnect the DMM leads from the MCl. 5.11.4 Connect the DMM leads to the MCl -15V current and voltage test jacks (figure 6). 5.11.5 Set the MCl -15V I TEST switch (figure 6) to -15; *the.DMM indication should not exceed 22 mA. Indicate acceptance on test report with checkmark. | 5.10.3 Using DMM, check that excitation at pin 18 (figure 1) is -5.000(+/-0.400)V; indicate acceptance on test report with checkmark. | ||
5.11.6 Set the MCl -15V I TEST switch to the unmarked position; disconnect the DMM leads from the MCl. 5.11. 7 Unplug PC202-Q2 from extender card cable connector. | 5.10.4 Set -5V/O switch SIB to O. | ||
NUMBER ATP449 SHEET 11 OF 13 | 5.10.5 Connect DMM COM lead to pin 18 and Hi lead to U7-7 (figure 1); the DMM indication should be -5.000(+/-0.400)V. Indicate acceptance on test report with checkmark. | ||
5.10.6 Disconnect DMM from PC202-Q2. | |||
* | 5.11 Current Consumption 5.11.1 Connect the DMM leads to the MCl +15V current and voltage test jacks (figure 6); set DMM to read DCmA. | ||
5.11.2 Set the MCl +15V I TEST switch (figure 6) to +15; the DMM indication should not exceed 22 mA. Indicate acceptance on test report with checkmark. | |||
( S/0 W/0 TESTED BY Paragraph/Step | 5.11.3 Set the MCl +15V I TEST switch to the unmarked position; disconnect the DMM leads from the MCl. | ||
5.11.4 Connect the DMM leads to the MCl -15V current and voltage test jacks (figure 6). | |||
+ 7.500(+/-0.007)V | 5.11.5 Set the MCl -15V I TEST switch (figure 6) to -15; *the.DMM indication should not exceed 22 mA. Indicate acceptance on test report with checkmark. | ||
+ 5.000(+/-0.007)V | 5.11.6 Set the MCl -15V I TEST switch to the unmarked position; disconnect the DMM leads from the MCl. | ||
+ 2.500(+/-0.007)V 0.000(+/-0.002)V 0.000(+/-0.002)V | ( 5.11. 7 Unplug PC202-Q2 from extender card cable connector. | ||
-2.500(+/-0.007)V | NUMBER REV ATP449 A SHEET 11 OF 13 | ||
-5.000(+/-0.007)V | |||
-7.500(+/-0.007)V | A(idyNE ENQINEEIII- COIIPOIIATION OUTPUT | ||
-10. 000 (+/-0. 007)V | * TEST A B | ||
+lSV VOLTAGE | |||
5.1.2 Regulated voltage output Load Regulation 5.2.1 Line Regulation 5.3.1 Output Ripple | * @ TEST JACK | ||
* NORTHRIDGE. | -15V VOLTAGE TEST JACK | ||
CA 91324 * (213) 886-8488 | * +15 | ||
* MCl TEST CONNECT DMM COM LEAD TO CURRENT TEST JACK AND. HI LEAD TO VOLTAGE TEST JACK Figure 6. MCl (Test) +/-15V Current Test Switch and Jack Locations NUMBER REV ATP449 A SHEET 12 OF 13 | |||
AlidyNE l!NOINE.111- COIIPOIIAT10N APPENDIX A SAMPLE TEST REPORT NUMBER REV ATP449 A SHEET 13 OF 13 | |||
( | |||
TEST REPORT PC202-Q2 ASSY Potentiometric Signal Conditioner S/0 CUSTOMER W/0 SERIAL NO. | |||
TESTED BY DATE Paragraph/Step Accepted Specification 5.3 Linearity and Symmetry 5.3.7 DMM Indication :s 10 mV 5.3.8 Table 2 Step Indication On 1 DMM +10.000(+/-0.005)V 2 DMM + 7.500(+/-0.007)V 3 PMM + 5.000(+/-0.007)V 4 DMM + 2.500(+/-0.007)V 5 DMM 0.000(+/-0.002)V 6 DMM 0.000(+/-0.002)V 7 DMM - 2.500(+/-0.007)V 8 DMM - 5.000(+/-0.007)V 9 DMM - 7.500(+/-0.007)V 10 DMM -10. 000 (+/-0. 007)V NUMBER REV ATP449 A QC SHEET 1 OF 3 | |||
( TEST REPORT ASSY PS324-Q2 Remote 24VDC Power Supply S/0 CUSTOMER W/0 SERIAL NO. | |||
TESTED BY DATE Paragraph/Step Accepted Specification. | |||
5.1.2 Regulated voltage output 24+/-1.5VDC Load Regulation 250mV max. | |||
5.2.1 Line Regulation 300mV max. | |||
5.3.1 Output Ripple 1OmV nns max. | |||
NUMBER REV ATP455 oc SHEET l OF l 8626 WILBUR AVENUE | |||
* NORTHRIDGE. CA 91324 * (213) 886-8488 | |||
* Telex No. 65-1303 | * Telex No. 65-1303 | ||
( AidyNE ENOINEEIUNO COllll'OIIATION TEST REPORT PC202-Q2 ASSY Potentiometric Signal Conditioner S/0 CUSTOMER W/0 SERIAL NO. TESTED BY DATE Paragraph/Step Accepted Specification 5.4 Gain Check 5.4.2 Table 3 Step Indication On 1 DMM +10.000(+/-0.005)V 2 DMM +10.000(+/-0.300)V 3 DMM +10.000(+/-0.300)V | |||
( | |||
-11.000(+/-1.000)V 5.5.3 DMM Indication | AidyNE ENOINEEIUNO COllll'OIIATION TEST REPORT PC202-Q2 ASSY Potentiometric Signal Conditioner S/0 CUSTOMER W/0 SERIAL NO. | ||
+11.000(+/-1.000)V 5.6 Single Ended Input 5.6.3 DMM Indication 0.000(+/-0.005)V 5.6.4 DMM Indication | TESTED BY DATE Paragraph/Step Accepted Specification 5.4 Gain Check 5.4.2 Table 3 Step Indication On 1 DMM +10.000(+/-0.005)V 2 DMM +10.000(+/-0.300)V 3 DMM +10.000(+/-0.300)V 4 DMM +10.000(+/-0.300)V 5 DMM +10.000(+/-0.300)V 5.5 Zero 5.5.2 DMM Indication -11.000(+/-1.000)V 5.5.3 DMM Indication +11.000(+/-1.000)V 5.6 Single Ended Input 5.6.3 DMM Indication 0.000(+/-0.005)V 5.6.4 DMM Indication +10.000(+/-0.0lO)V 5.7 Calibration Circuit 5.7.4 DMM Indication 0.000(+/-0.lOO)V 5.8 Input Resistance 5.8.3 DMM Indication 0.95-1.30M NUMBER REV ATP449 A QC SHEET 2 OF 3 | ||
+10.000(+/-0.0lO)V 5.7 Calibration Circuit 5.7.4 DMM Indication 0.000(+/-0.lOO)V 5.8 Input Resistance 5.8.3 DMM Indication 0.95-1.30M NUMBER REV ATP449 A QC SHEET 2 OF 3 | |||
TEST REPORT PC202-Q2 ASSY Potentiometric Signal Conditioner S/0 W/0 TESTED BY Paragraph/Step 5.8.4 DMM Indication 5.9 Filter 5.9.4.2 Frequency Counter Indication 5.9.5.2 Frequency Counter Indication 5.9.6.2 Frequency Counter Indication 5.9.7.2 Frequency Counter Indication 5.10 Excitation Check 5.10.2 DMM Indication | TEST REPORT PC202-Q2 ASSY Potentiometric Signal Conditioner S/0 CUSTOMER W/0 SERIAL NO. | ||
+ 5.000(+/-0.400)V | TESTED BY DATE Paragraph/Step Accepted Specification 5.8.4 DMM Indication 0.95-l.30M 5.9 Filter 5.9.4.2 Frequency Counter Indication 15(+/-2)Hz 5.9.5.2 Frequency Counter Indication 45(+/-7)Hz 5.9.6.2 Frequency Counter Indication 100(+/-15)Hz 5.9.7.2 Frequency Counter Indication 200(+/-30)Hz 5.10 Excitation Check 5.10.2 DMM Indication + 5.000(+/-0.400)V 5.10.3 DMM Indication - 5.000(+/-0.400)V 5.10.5 DMM Indication - 5.000(+/-0.400)V 5.11 Current Consumption 5.11.2 DMM Indication *22 mA max. | ||
-5.000(+/-0.400)V | 5.11.5 DMM Indication 22 mA max. | ||
-5.000(+/-0.400)V | NUMBER REV ATP449 A oc SHEET 3 OF 3}} | ||
*22 mA max. 22 mA max. OF 3 |
Latest revision as of 05:06, 23 February 2020
ML18142A111 | |
Person / Time | |
---|---|
Site: | Surry, 05000000 |
Issue date: | 05/28/1981 |
From: | Kamerman L VALIDYNE ENGINEERING SALES CORP. |
To: | |
Shared Package | |
ML18130A405 | List: |
References | |
ATP449, NUDOCS 8411200437 | |
Download: ML18142A111 (18) | |
Text
AlidyNE ENGINEERING CORPOIIATION REVISIONS LTR ECO DESCRIPTION DATE APPROVED A See DCN 5 28 81 ......~.
1
( .. ~i~ 1 iB8ia F
7 0 ~6M:>i!~ \
SIGNATURE TITLE PC202-Q2 Buffer Amplifier PROD TEST NGINEERING
- ....-------,,:;.,~-=...:::~----:.......:._ _ _ _..,_______-f NUMBER REV QUAL CONTROL ATP449 A SHEET 1 OF 13 8626 WILBUR AVENUE
- NORTHRIDGE. CA 91324 * (213) 886-8488
- Telex No. 65-1303 VEC 304-11/80
AlidyNE l!NGIN **IIINCI COlll"OIIATlON 1.0 SCOPE This document defines the Acceptance Test Procedure (ATP) for the PC202-Q2 Potentiometric Signal Conditioner. The ATP performs functional checks of all operating characteristics. A sample of the Test Report to be used with this ATP is contained in Appendix A.
2.0 EQUIPMENT REQUIRED Table 1 lists the test equipment required to perform the ATP.
Table 1. Equipment Required for ATP Part No.
Description Manufacturer or Model
- Alternate MCl (Test) Validyne -- None Extender Card (MC1-MC170) Validyne -- None BA Test Cable DC Source Validyne Validyne TE-124 None None Digital Multimeter (DMM) (2) Data Precision 245 Commercial Equivalent Oscilloscope B & K 1470 Commercial
- Equivalent Function Generator
- Exact 100 Commercial Equivalent Frequency Counter Hewlett Packard 5314A Commercial Equivalent 3.0 PRELIMINARY PROCEDURE 3.1 Plug extender card into front panel connector on MC!.
3.2 Refer to figure 1 and set switches and controls on PC202-Q2 as follows:
Switch or Control Setting SPAN (R24) Full CW GAIN (S4) Xl FILTER (S2) 200 DC/AC (S3) DC IN/OUT (SlA) OUT
-SV/0 (SlB) -sv DIFF/SINGLE ENDED (SlC) DIFF 3.3 Plug PC202-Q2 into extender card cable connector.
3.4 Refer to figure 1 for location, and visually check that resistors R8 and*
R12 are each 1 Megohm, 5%.
NUMBER REV ATP449 A SHEET 2 OF 13
AlidyNE l!-INalllll- co11..a11ATION Appendix A 11 11 Sample Test Report NUMBER ATP455 SHEET 1 OF l
ATED TERMINAL
( TYP 7 PLACES)
Cl 1110
@ R50 IZERO CONTROL 499K CfilI]
12.lK .+15V
....z ;;;Cl w
z ex:
e-QD:
I
!PAN 0 w
@ @ R24 SPAN.
24.9K1
~lff<[1]-e *-15V 0..
0 Cl
..J 0
[ill] u Vl
~
GAIN [ill]lM CAL R4 Ill II *-rnrif&-e [illlM BAL 2 4
1 3
,~----: :1 D S4 1~-1 IMIN IN -5V DIFF 6
8 5
7 n 10 9 111111 12 11 Ill C I"u" ZERO I
SINGLE 14 16 13 15
---u I ~ HI S2 \
OUT 0 ENDED
' 18 17 EJ 45 20 19
'&" 22 21 i
DC CM , 24 23 DC/AC AC ADJ ',, 26 25 28 27 0 +11 TP2 \ 30 29
~
r----,
0 -11 TPl I R11 I
@ 56.2K I I 0 out TP3 1&
L ___ .JI rem BAL m ii I-*
NOTE:
& ONLY ONE BAL POT IS IHSTALLED ON THE BOARD, AND IT IS NORMALLY RlS; SOME UNITS MAY HAVE Rll INSTALLED INSTEAD OF Rl 5 i Q.
8-
- z:
-~i~z C:
3:
m m :I.
- a i "'
en
- x m
!!I C)
- a m
Figure 1. PC202-Q2 Parts Locations L____
AlidyNE ENGINl&l!IIING COIIPOIIAT10N 3.5 If necessary, connect MCl to 115 Vac and press MCl power switch; observe that power-on indicator lights.
4.0 INITIAL TEST SETUP 4.1 Connect DMM to PC202-Q2 as shown in figure 2.
MCI(TEST)
EXTENDER PC202-Q2 CARD
& JUNCTION U4-6 &Rl9 SIG GND 24 HI DMM NOTES:
- 1. BOXED CALLOUT jxxxl INDICATES PANEL OR BOARD MARKINGS
& SEE FIGURE l FOR LOCATIONS Figure 2. Initial Test Setup NOTE: Unless otherwise indicated, all switches, controls, potentiometers, and test points referred to in the ATP procedures that follow are located on the PC202-Q2; see figure 1 for locations.
NUMBER REV ATP449 A SHEET 4 OF 13
AlidyNE l!NGINEl!III- COIIPOIIATION
(
5.0 FUNCTIONAL TESTS Perform all tests and in the order given~
5.1 Null Adjustment 5.1.1 On connector of PC202-Q2 (figure 1), jumper pins 20 and 22 together and connect to signal ground (pin 24).
NOTE BAL potentiometer Rll may be installed on some units instead of R15. On these units, adjust Rll in step 5.1.2.
5.1.2 Adjust BAL potentiometer Rl5 for 0.000(+/-0.002)V DC output on DMM.
5.1.3 Remove the ground from pins 20 and 22 of connector.
5.2 Common Mode Adjustment 5.2.1 On connector of PC202-Q2 (figure 1), jumper together pins 20 and 22 and connect to de source and DMM as shown in. figure 3.
5.2.2 Set polarity switch of de source to plus(+) and output to +10.000(+/-0.005)V.
5.2.3 Adjust CM ADJ potentiometer R18 for 0.000(+/-0.002)V DC output on DMM.
5.2.4 Set polarity switch of de source to minus(-); output on DMM should be 0.000(+/-0.005)V DC.
5.2.5 Repeat steps 5.2.2 thru 5.2.4, if necessary.
5.2.6 Remove jumper'from pins 20 and 22 and disconnect de source and DMM
. from PC202-Q2.
NOTE Any change in the value of RlOl (open circuit to 24.9K range) requires that paragraphs 5.1 and 5.2 be performed.
5.3 Linearity, Symmetry, and Noise 5.3.1 Using the BA test cable, connect de source and DMM to input connector on*rear panel of MCl as shown in figure 4.
5.3.2 Connect DMM to OUTPUT A of MCl as shown in figure 4.*
5.3.3 Set output of de source to 0.0000(+/-0.0005)V DC. NUMBER REV ATP449 A 5.3.4 Adjust ZERO potentiometer R44 for 0.000(+/-0.002)V DC output on DMM. SHEET 5 OF 13
AlidyNE ENGINEEIII- COll"'IIATION MCI(TEST)
- EXTENDER CARD r - ffi U4-6 PC202-Q2 JUNCTION SIG GND
-INPUT 24 - C)
- +INPUT
-- 224 20 Rl9
\ \I \
!COM
)
I HI
) RED
'I J IDC OUTPUT!
¥ BLK ~.) .:> HI DMM DC SOURCE Dr,tH NOTES:
- 1. BOXED CALLOUT lxxxl INDICATES PANEL OR BOARd MARKINGS
~ SEE FIGURE 1 FOR LOCATIONS Figure 3. Com:mon Mode ~djustment Test Setup DC SOURCE MCI(TEST)
!DC OUTPUT! BA TEST EXTENDER PC202-Q2 CABLE CARD RED BLACK I OUTPUT AI RED HI HI DMM NOTES:
- 1. BOXED C~LLOUT jxxxj INDICATES PANEL OR BOARD MARKINGS
- 2. SEE FIGURE 1 FOR LOCATION Figure 4. Linearity and Symmetry Test Setup NUMBER REV ATP449 A*
SHEET 6 OF 13
~~-""~..,~ \A/11 "0110 A.\/C'P.,111C' a l\lr"IOTUClr"'\re f'"A n .. ..,.., ... , - , ....... , .... ,.,,.. ,., .. ,.,,, - T ..
AlidyNE ENQIN. . .IINQ co11..allATION
(
5.3.5 Set output of de source to +10.000(+/-0.00Z)V.
5.3.6 Adjust SPAN control R24 for +10.000(+/-0.00S)V output on DMM.
5.3.7 Set DMM to read ACmV; the noise indication on the DMM should be less than or equal to 10 mV AC. Indicate acceptance on test report with checkmark.
5.3.8 Perform the steps in table 2 to check linearity and symmetry of PC202-Q2.
For steps 1 thru 5, set POLARITY switch of de source to plus(+) and input as indicated; for steps 6 thru 10, set POLARITY switch of de source to minus(-) and input as indicated. Indicate acceptance on test report with checkmark.
Table 2. Linearity and Symmetry Check DC Source Output Specification Step Input (VDC) On DMM (VDC) 1 +10.000 +10.000+/-0.005 2 + 7.500 + 7.5QQ+/-Oa007 3 + 5.000 + 5.000+/-0.007 4 + 2.500 + 2.500+/-0.007 5 + 0.000 0.000::to.002 6
7
- 0.000 -
0.000+/-0.002
- 2.500 - 2.SOO+/-Oa0,07 8 - 5.000 - 5.000+/-0.007 9 - 7a500 - 7.500+/-0.007 10 -10.000 -10.000+/-0 .. 007 5.4 Gain 5.4.1 Set POLARITY switch of de source to plus(+).
5.4.2 Perform the steps in table 3 to check gain of PC202-Q2; for each step, set GAIN switch S4 and input from the de source as indicated. Indicate acceptance on test report with checkmark.
Table 3. Gain Check Gain Switch DC Source Output Specification Step S4 Input (VDC) On DMM (VDC) 1 X1 +10.000 +10.000+/-0.005 2 X2.5 + 4.000 +10.000+/-0.300 3 XS + 2 .. 000 +10.000+/-0.300 4 XlO + 1.000 +10.000+/-0.300 5 X25 + 0.400 +10.000+/-0.300 NUMBER REV ATP449 A SHEET 7 OF 13
A(idyNE l!NQIN **IIINQ COlll"OIIArtON
(
5.4.3 Disconnect BA test cable from MCl.
5.5 Zero 5.5.1 Set GAIN switch S4 to Xl and IN/OUT switch SlA to IN; on connector of PC202-Q2 (figure 1), jumper pins 20 and 22 together and connect to signal ground (pin 24).
5.5.2 Adjust ZERO CONTROL R50 maximum counterclockwise (CCW); output on DMM should be -11.000(+/-1.000)V. Indicate acceptance on test report with checkmark.
5.5.3 Adjust ZERO CONTROL R50 maximum clockwise (CW); output on DMM should be
+11.000(+/-1.000)V. Indicate acceptance on test report with checkmark.
5.5.4 Set IN/OUT switch SlA to OUT.
5.5.5 Remove jumper and ground from pins 20 and 22 of connector.
5.6 Single Ended Input 5.6.1 Set DIFF/SINGLE ENDED switch SlC to SINGLE ENDED.
5.6.2 Reconnect BA test cable to MCl; -ensure GAIN switch S4 isset to Xl.
5.6.3 Connect negative terminal (black) of de source to signal ground (pin 24) on the PC202-Q2 connector; set de source output to 0.0000(+/-0.0002)V. The output on DMM at OUTPUT A of MCl should be 0.000(+/-0.005)V DC. Indicate acceptance on test report with checkmark.
5.6.4 Set output of de source to +10.000(+/-0.005)V; the output on DMM at OUTPUT A of MCl should be +10.000(+/-0.0lO)V. Indicate acceptance on test report with checkmark.
5.7 Calibration Circuit 5.7.1 Disconnect BA test cable from de source and DMM.
5.7.2 On connector of PC202-Q2 (figure 1), connect pin 28 to signal ground (pin 24).
5.7.3 If resistor R3 (figure 1) is connected to +15V, adjust CAL potentiometer R4 for +10.000(+/-0.lOO)V output on DMM; if R3 is connected to -15V, adjust R4 for -10.000(+/-0.lOO)V on DMM.
5.7.4 Adjust CAL potentiometer R4 full CCW; the output indication on DMM should be 0.000(+/-0.lOO)V. Indicate acceptance on test report with checkmark.
5.7.5 Remove ground from pin 28 of connector.
NUMBER REV ATP449 A SHEET 8 OF 13
AlidyNE l!NGINl!ERING CORPORATION 5.8 Input Resistance 5.8.1 Press MCl power switch; observe that power-on indicator goes out.
5.8.2 Set DIFF/SINGLE ENDED switch SlC to DIFF; set DMM to read resistance on the 10 Megohm range.
5.8.3 Connect DMM between pin 22 of PC202-Q2 and Ul-5 (figure 1); the DMM indication should be between 0.95 and 1.30 Megohms. Indicate acceptance on test report with checkmark; disconnect DMM.
5.8.4 Connect DMM between pin 20 and junction of R7 and Ul-12 (figure 1); the DMM indication should be between 0.95 and 1.30 Megohms. Indicate acceptance on test report with checkmark;*disconnect DMM.
5.8.5 Press MCl power switch; observe that power-on indicator lights.
5.9 Filter 5.9.1 Connect function generator, frequency counter, and oscilloscope, as shown in figure 5.
FUNCTION MCl(TEST)
.GENERATOR
- I OUTPUT I EXTENDER CARD PC202-Q2 I OUTPUT A I BLACK RED BNC/BANANA PATCH CORD I INPUT I FREQUENCY @[TI COUNTER OSCILLOSCOPE NOTES:
- 1. BOXED CALLOUT~- INDICATES PANEL OR BOARD MARKINGS Figure 5. Filter Test Setup
(
NUMBER REV ATP449 A
SHEET 9 OF 13
AlidyNE
( 1!-IN**IIINQ COIIPOIIATION 5.9.2 Set oscilloscope for lV/DIV display, external trigger, and DC coupling.
5.9.3 Set PC202-Q2 switches as follows:
Switch Setting GAIN (S4) no FILTER (S2) 15 HZ DC/AC (S3) AC IN/OUT (SlA) OUT DIFF/SINGLE ENDED (SlC) DIFF 5.9.4 15 Hz Test 5.9.4.1 Set function generator for a 1.5 Hz sinewave output, as indicated on the frequency counter; adjust output f~r a 7-division display on oscilloscope.
5.9.4.2 Increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 15(+/-2)Hz.
Indicate acceptance on test report with checkmark.
5.9.5 45 Hz Test 5.9.5.1 Set FILTER switch S2 to 45 HZ.
5.9.5.2 Increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 45(+/-7)Hz.
Indicate acceptance on test report with checkmark.
5.9.6 100.Hz Test 5.9.6.1 Set FILTER switch S2 to-100 HZ.
5.9.6.2 increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 100(+/-15)Hz. Indicate acceptance on test report with checkmark.
5.9.7 200 Hz Test
- 5.9.7.1 Set FILTER switch S2 to 200 HZ.
NUMBER REV ATP449 A SHEET 10 OF 13
A(idyNE ENGIN . .iRI- CORPORATION 5.9.7.2 Increase function generator output frequency until oscilloscope display decreases to 5 divisions; the frequency counter should indicate 200(+/-30)Hz. Indicate acceptance on test report with checkmark.
5.9.7.3 Disconnect oscilloscope and BA test cable from MCl.
5.10 Excitation 5.10.1 Connect DMM COM lead to signal ground (pin 24) of PC202-Q2 (figure 1);
set DMM to read DC.
5.10.2 Using DMM, check that excitation at pin 16 (figure 1) is +5.000(+/-0.400)V; indicate acceptance on test report with checkmark.
5.10.3 Using DMM, check that excitation at pin 18 (figure 1) is -5.000(+/-0.400)V; indicate acceptance on test report with checkmark.
5.10.4 Set -5V/O switch SIB to O.
5.10.5 Connect DMM COM lead to pin 18 and Hi lead to U7-7 (figure 1); the DMM indication should be -5.000(+/-0.400)V. Indicate acceptance on test report with checkmark.
5.10.6 Disconnect DMM from PC202-Q2.
5.11 Current Consumption 5.11.1 Connect the DMM leads to the MCl +15V current and voltage test jacks (figure 6); set DMM to read DCmA.
5.11.2 Set the MCl +15V I TEST switch (figure 6) to +15; the DMM indication should not exceed 22 mA. Indicate acceptance on test report with checkmark.
5.11.3 Set the MCl +15V I TEST switch to the unmarked position; disconnect the DMM leads from the MCl.
5.11.4 Connect the DMM leads to the MCl -15V current and voltage test jacks (figure 6).
5.11.5 Set the MCl -15V I TEST switch (figure 6) to -15; *the.DMM indication should not exceed 22 mA. Indicate acceptance on test report with checkmark.
5.11.6 Set the MCl -15V I TEST switch to the unmarked position; disconnect the DMM leads from the MCl.
( 5.11. 7 Unplug PC202-Q2 from extender card cable connector.
NUMBER REV ATP449 A SHEET 11 OF 13
A(idyNE ENQINEEIII- COIIPOIIATION OUTPUT
- TEST A B
+lSV VOLTAGE
- @ TEST JACK
-15V VOLTAGE TEST JACK
- +15
- MCl TEST CONNECT DMM COM LEAD TO CURRENT TEST JACK AND. HI LEAD TO VOLTAGE TEST JACK Figure 6. MCl (Test) +/-15V Current Test Switch and Jack Locations NUMBER REV ATP449 A SHEET 12 OF 13
AlidyNE l!NOINE.111- COIIPOIIAT10N APPENDIX A SAMPLE TEST REPORT NUMBER REV ATP449 A SHEET 13 OF 13
(
TEST REPORT PC202-Q2 ASSY Potentiometric Signal Conditioner S/0 CUSTOMER W/0 SERIAL NO.
TESTED BY DATE Paragraph/Step Accepted Specification 5.3 Linearity and Symmetry 5.3.7 DMM Indication :s 10 mV 5.3.8 Table 2 Step Indication On 1 DMM +10.000(+/-0.005)V 2 DMM + 7.500(+/-0.007)V 3 PMM + 5.000(+/-0.007)V 4 DMM + 2.500(+/-0.007)V 5 DMM 0.000(+/-0.002)V 6 DMM 0.000(+/-0.002)V 7 DMM - 2.500(+/-0.007)V 8 DMM - 5.000(+/-0.007)V 9 DMM - 7.500(+/-0.007)V 10 DMM -10. 000 (+/-0. 007)V NUMBER REV ATP449 A QC SHEET 1 OF 3
( TEST REPORT ASSY PS324-Q2 Remote 24VDC Power Supply S/0 CUSTOMER W/0 SERIAL NO.
TESTED BY DATE Paragraph/Step Accepted Specification.
5.1.2 Regulated voltage output 24+/-1.5VDC Load Regulation 250mV max.
5.2.1 Line Regulation 300mV max.
5.3.1 Output Ripple 1OmV nns max.
NUMBER REV ATP455 oc SHEET l OF l 8626 WILBUR AVENUE
- NORTHRIDGE. CA 91324 * (213) 886-8488
- Telex No. 65-1303
(
AidyNE ENOINEEIUNO COllll'OIIATION TEST REPORT PC202-Q2 ASSY Potentiometric Signal Conditioner S/0 CUSTOMER W/0 SERIAL NO.
TESTED BY DATE Paragraph/Step Accepted Specification 5.4 Gain Check 5.4.2 Table 3 Step Indication On 1 DMM +10.000(+/-0.005)V 2 DMM +10.000(+/-0.300)V 3 DMM +10.000(+/-0.300)V 4 DMM +10.000(+/-0.300)V 5 DMM +10.000(+/-0.300)V 5.5 Zero 5.5.2 DMM Indication -11.000(+/-1.000)V 5.5.3 DMM Indication +11.000(+/-1.000)V 5.6 Single Ended Input 5.6.3 DMM Indication 0.000(+/-0.005)V 5.6.4 DMM Indication +10.000(+/-0.0lO)V 5.7 Calibration Circuit 5.7.4 DMM Indication 0.000(+/-0.lOO)V 5.8 Input Resistance 5.8.3 DMM Indication 0.95-1.30M NUMBER REV ATP449 A QC SHEET 2 OF 3
TEST REPORT PC202-Q2 ASSY Potentiometric Signal Conditioner S/0 CUSTOMER W/0 SERIAL NO.
TESTED BY DATE Paragraph/Step Accepted Specification 5.8.4 DMM Indication 0.95-l.30M 5.9 Filter 5.9.4.2 Frequency Counter Indication 15(+/-2)Hz 5.9.5.2 Frequency Counter Indication 45(+/-7)Hz 5.9.6.2 Frequency Counter Indication 100(+/-15)Hz 5.9.7.2 Frequency Counter Indication 200(+/-30)Hz 5.10 Excitation Check 5.10.2 DMM Indication + 5.000(+/-0.400)V 5.10.3 DMM Indication - 5.000(+/-0.400)V 5.10.5 DMM Indication - 5.000(+/-0.400)V 5.11 Current Consumption 5.11.2 DMM Indication *22 mA max.
5.11.5 DMM Indication 22 mA max.
NUMBER REV ATP449 A oc SHEET 3 OF 3