ML060380188

Millstone Unit 2 - RAI Response to Generic Letter 2004-02, Potential Impact of Debris Blockage on Emergency Recirculation During Design-Basis Accidents at Pressurized Water Reactors (Tac MC4694)

ML060380188
Person / Time
Site:	Millstone
Issue date:	02/09/2006
From:	Nerses V Plant Licensing Branch III-2
To:	Christian D A Dominion Nuclear Connecticut
Nerses V, NRR//DLPM, 415-1484
References
TAC MC4694
Download: ML060380188 (9)

Text

February 9, 2006Mr. David A. ChristianSr. Vice President and Chief Nuclear Officer Dominion Nuclear Connecticut, Inc.

Innsbrook Technical Center 5000 Dominion Boulevard Glen Allen, VA 23060-6711

SUBJECT:

MILLSTONE POWER STATION, UNIT NO. 2, REQUEST FOR ADDITIONALINFORMATION RE: RESPONSE TO GENERIC LETTER 2004-02, "POTENTIAL IMPACT OF DEBRIS BLOCKAGE ON EMERGENCY RECIRCULATION DURING DESIGN-BASIS ACCIDENTS AT PRESSURIZED-WATER REACTORS" (TAC NO. MC4694)

Dear Mr. Christian:

On September 13, 2004, the Nuclear Regulatory Commission (NRC) issued Generic Letter(GL) 2004-02, "Potential Impact of Debris Blockage on Emergency Recirculation During Design Basis Accidents at Pressurized-Water Reactors," as part of the NRC's efforts to assess thelikelihood that the emergency core cooling system (ECCS) and containment spray system(CSS) pumps at domestic pressurized water reactors (PWRs) would experience a debris-induced loss of net positive suction head margin during sump recirculation. The NRC issuedthis GL to all PWR licensees to request that addressees (1) perform a mechanistic evaluation using an NRC-approved methodology of the potential for the adverse effects of post-accidentdebris blockage and operation with debris-laden fluids to impede or prevent the recirculation functions of the ECCS and CSS following all postulated accidents for which the recirculation of these systems is required, and (2) implement any plant modifications that the above evaluationidentifies as being necessary to ensure system functionality. Addressees were also required tosubmit information specified in GL 2004-02 to the NRC in accordance with Title 10 of the Codeof Federal Regulations Section 50.54(f). Additionally, in the GL, the NRC establis hed aschedule for the submittal of the written responses and the completion of any corrective actions identified while complying with the requests in the GL.By letter dated March 4, 2005, as supplemented by letter dated September 1, 2005, DominionNuclear Connecticut, Inc. provided a response to the GL. The NRC staff is reviewing andevaluating your response along with the responses from all PWR licensees. The NRC staff hasdetermined that responses to the questions in the enclosure to this letter are necessary in order for the staff to complete its review. Please note that the Office of Nuclear Reactor Regulation'sDivision of Component Integrity is st ill conducting its initial reviews with respect to coatings. Although some initial coatings questions are included in the enclosure to this letter, the NRC might issue an additional request for information regarding coatings issues in the near future.

D. Christian-2-Please provide your response within 60 days from the date of this letter. If you have anyquestions, please contact me at (301) 415-1484.Sincerely,/RA/Victor Nerses, Senior Project ManagerPlant Licensing Branch I-2 Division of Operating Reactor Licensing Office of Nuclear Reactor RegulationDocket No. 50-336

Enclosure:

Request for Additional Informationcc w/encl: See next page D. Christian-2-Please provide your response within 60 days from the date of this letter. If you have anyquestions, please contact me at (301) 415-1484.Sincerely,/RA/Victor Nerses, Senior Project ManagerPlant Licensing Branch I-2 Division of Operating Reactor Licensing Office of Nuclear Reactor RegulationDocket No. 50-336

Enclosure:

Request for Additional Informationcc w/encl: See next pageDISTRIBUTION

PUBLICRidsNrrDorlDprRArchitzel LPL1-2 Reading FileWBatemanTHaffera RidsNrrDorlLplbRidsNrrPMJHopkinsJLehning RidsNrrLACRaynorMmurphyHWagage RidsNrrPMVNersesPkleinSLu RidsOgcRpMYoderJHannon RidsAcrsAcnwMailCenterMScott RidsRgn1MailcenterAccession No.: ML060380188*per e-mailOFFICELPL1-2/PMLPL1-2/LADSS/SSIBDCI/CSGBLPL1-2/BCNAMEVNerses: cm(GMiller for)CRaynorDSolorio*EMurphy*DRobertsDATE2/09/062/09/092/06/062/08/062/09/06OFFICIAL RECORD COPY Millstone Power Station, Unit No. 2 cc:

Lillian M. Cuoco, EsquireSenior Counsel Dominion Resources Services, Inc.

Building 475, 5 th FloorRope Ferry Road Waterford, CT 06385Edward L. Wilds, Jr., Ph.D.Director, Division of Radiation Department of Environmental Protection 79 Elm Street Hartford, CT 06106-5127Regional Administrator, Region IU.S. Nuclear Regulatory Commission 475 Allendale Road King of Prussia, PA 19406First SelectmenTown of Waterford 15 Rope Ferry Road Waterford, CT 06385Charles Brinkman, DirectorWashington Operations Nuclear Services Westinghouse Electric Company 12300 Twinbrook Pkwy, Suite 330 Rockville, MD 20852Senior Resident InspectorMillstone Power Stationc/o U.S. Nuclear Regulatory Commission

P.O. Box 513 Niantic, CT 06357Mr. J. Alan PriceSite Vice President Dominion Nuclear Connecticut, Inc.

Building 475, 5 th FloorRope Ferry Road Waterford, CT 06385Mr. John MarkowiczCo-Chair Nuclear Energy Advisory Council 9 Susan Terrace Waterford, CT 06385Mr. Evan W. WoollacottCo-Chair Nuclear Energy Advisory Council 128 Terry's Plain Road Simsbury, CT 06070Ms. Nancy Burton147 Cross Highway Redding Ridge, CT 00870Mr. Chris L. FunderburkDirector, Nuclear Licensing and Operations Support Dominion Resources Services, Inc.

Innsbrook Technical Center 5000 Dominion Boulevard Glen Allen, VA 23060-6711Mr. David W. DodsonLicensing Supervisor Dominion Nuclear Connecticut, Inc.

Building 475, 5 th FloorRope Ferry Road Waterford, CT 06385Mr. Joseph Roy, Director of Operations Massachusetts Municipal Wholesale Electric Company Moody Street

P.O. Box 426 Ludlow, MA 01056 EnclosureGL 2004-02 RAI QuestionsPlant Materials1.Identify the name and bounding quantity of each insulation material generated by alarge-break loss-of-coolant accident (LBLOCA). Include the amount of these materials transported to the containment pool. State any assumptions used to provide this response.2.Identify the amounts (i.e., surface area) of the following materials that are: (a) submerged in the containment pool following a loss-of-coolant accident (LOCA),

(b) in the containment spray zone following a LOCA: - aluminum- zinc (from galvanized steel and from inorganic zinc coatings)

- copper

- carbon steel not coated

- uncoated concreteCompare the amounts of these materials in the submerged and spray zones at yourplant relative to the scaled amounts of these materials used in the Nuclear Regulatory Commission (NRC) nuclear industry jointly-sponsored Integrated Chemical Effects Tests(ICET) (e.g., 5x the amount of uncoated carbon steel assumed for the ICETs). 3.Identify the amount (surface area) and material (e.g., aluminum) for any scaffoldingstored in containment. Indicate the amount, if any, that would be submerged in the containment pool following a LOCA. Clarify if scaffolding material was included in the response to Question 2.4.Provide the type and amount of any metallic paints or non-stainless steel insulationjacketing (not included in the response to Question 2) that would be either submerged or subjected to containment spray.Containment Pool Chemistry 5.Provide the expected containment pool pH during the emergency core cooli ng syst em(ECCS) recirculation mission time following a LOCA at the beginning of the fuel cycleand at the end of the fuel cycle. Identify any key assumptions.6.For the ICET environment that is the most similar to your plant conditions, compare theexpected containment pool conditions to the ICET conditions for the following items:

boron concentration, buffering agent concentration, and pH. Identify any othersignificant differences between the ICET environment and the expected plant-specificenvironment.7.(Not Applicable). Plant-Specific Chemical Effects8.Discuss your overall strategy to evaluate potential chemical effects includingdemonstrating that, with chemical effects considered, there is sufficient net positive suction head (NPSH) margin available during the ECCS mission time. Provide an estimated date with milestones for the completion of all chemical effects evaluations.9.Identify, if applicable, any plans to remove certain materials from the containmentbuilding and/or to make a change from the existing chemicals that buffer containment pool pH following a LOCA.10.If bench-top testing is being used to inform plant specific head loss testing, indicate howthe bench-top test parameters (e.g., buffering agent concentrations, pH, materials, etc.)

compare to your plant conditions. Describe your plans for addressing uncertainties related to head loss from chemical effects including, but not limited to, use of chemical surrogates, scaling of sample size and test durations. Discuss how it will be determi ned that allowances made for chemical effects are conservative.Plant Environment Specific 11.Provide a detailed description of any testing that has been or will be performed as partof a plant-specific chemical effects assessment. Identify the vendor, if applicable, that will be performing the testing. Identify the environment (e.g., borated water at pH 9,deionized water, tap water) and test temperature for any plant-specific head loss or transport tests. Discuss how any differences between these test environments and your plant containment pool conditions could affect the behavior of chemical surrogates.

Discuss the criteria that will be used to demonstrate that chemical surrogates producedfor testing (e.g., head loss, flume) behave in a similar manner physically and chemically as in the ICET environment and plant containment pool environment.12.For your plant-specific environment, provide the maximum projected head loss resultingfrom chemical effects (a) within the first day following a LOCA, and (b) during the entire ECCS recirculation mission time. If the response to this question will be based ontesting that is either planned or in progress, provide an estimated date for providing this information to the NRC.ICET 1 and ICET 5 Plants 13.(Not Applicable).Trisodium Phosphate (TSP) Plants 14.Given the results from the ICET #3 tests (Agencywide Document Access andManagement System (ADAMS) Accession No. ML053040533) and NRC-sponsoredhead loss tests (Information Notice 2005-26 and Supplement 1), estimate the concentration of dissolved calcium that would exist in your containment pool from all containment sources (e.g., concrete and materials such as calcium silicate, MariniteŽ,mineral wool, kaylo) following a LBLOCA and discuss any ramifications related to the evaluation of chemical effects and downstream effects. 15.(Not Applicable).16.(Not Applicable).Additional Chemical Effects Questions 17.(Not Applicable).18.(Not Applicable).

19.(Not Applicable).

20.(Not Applicable).

21.(Not Applicable).

22.(Not Applicable).

23.(Not Applicable).

24.(Not Applicable).Coatings Generic - All Plants25.Describe how your coatings assessment was used to identify degradedqualified/acceptable coatings and determine the amount of debris that will result fromthese coatings. This should include how the assessment technique(s) demonstrates that qualified/acceptable coatings remain in compliance with plant licensing requirements for design-basis accident (DBA) performance. If current examination techniques cannot demonstrate the coatings' ability to meet plant licensing requirementsfor DBA performance, licensees should describe an augmented testing and inspection program that provides assurance that the qualified/acceptable coatings continue to meetDBA performance requirements. Alternately, assume all containment coatings fail and describe the potential for this debris to transport to the sump.Plant Specific26.(Not Applicable).

27.(Not Applicable).

28.(Not Applicable).

29.Your GL response indicates that you may pursue a reduction in the radius of the ZOI forcoatings. Identify the radius of the coatings ZOI that will be used for your final analysis. In addition, provide the test methodology and data used to support your proposed ZOI.

Provide justification regarding how the test conditions simulate or correlate to actual plant conditions and will ensure representative or conservative treatment in the am ountsof coatings debris generated by the interaction of coatings and a two-phase jet. Identify all instances where the testing or specimens used deviate from actual plant conditions (i.e., irradiation of actual coatings vice samples, aging differences, etc.). Provide justification regarding how these deviations are accounted for with the test demonstrating the proposed ZOI.30.The NRC staff's safety evaluation (SE) on the NEI quidance report, NEI 04-07,addresses two distinct scenarios for formation of a fiber bed on the sump screen surface. For a thin bed case, the SE states that all coatings debris should be treated asparticulate and assumes 100% transport to the sump screen. For the case in which no thin bed is formed, the staff's SE states that the coatings debris should be sized basedon plant-specific analyses for debris generated from within the ZOI and from outside the ZOI, or that a default chip size equivalent to the area of the sump screen openings should be used (Section 3.4.3.6). Describe how your coatings debris characteristics are modeled to account for your plant-specific fiber bed (i.e. thin bed or no thin bed). If your analysis considers both a thin bed and a non-thin bed case, discuss the coatings debris characteristics assumed for each case. If your analysis deviates from the coatings debris characteristics described in the staff- approved methodology, provide justification to support your assumptions.31.Your submittal indicated that you had taken samples for latent debris in yourcontainment, but did not provide any details regarding the number, type, and location of samples. Please provide these details.32.Your submittal did not provide details regarding the characterization of latent debrisfound in your containment as outlined in the NRC SE. Please provide these details.33.Was/will "leak before break" be used to analyze the potential jet impingement loads onthe new ECCS sump screen?34.You indicated that you would be evaluating downstream effects in accordance withWCAP 16406-P. The NRC is currently involved in discussions with the WestinghouseOwner's Group (WOG) to address questions/concerns regarding this WCAP on a generic basis, and some of these discussions may resolve issues related to your particular station. The following issues have the potential for generic resolution; however, if a generic resolution cannot be obtained, plant-specific resolution will berequired. As such, formal RAIs will not be issued on these topics at this time, but maybe needed in the future. It is expected that your final evaluation response willspecifically address those portions of the WCAP used, their applicability, and exceptionstaken to the WCAP. For your information, topics under ongoing discussion include:ee.Wear rates of pump-wetted materials and the effect of wear on componentoperation ff.Settling of debris in low flow areas downstream of the strainer or credit forfiltering leading to a change in fluid compositiongg.Volume of debris injected into the reactor vessel and core region hh.Debris types and properties ii.Contribution of in-vessel velocity profile to the formation of a debris bed or clog jj.Fluid and metal component temperature impactkk.Gravitational and temperature gradients ll.Debris and boron precipitation effects mm.ECCS injection paths nn.Core bypass design features oo.Radiation and chemical considerations pp.Debris adhesion to solid surfaces qq.Thermodynamic properties of coolant35.Your response to GL 2004-02 question (d) (viii) indicated that an active strainer designwill not be used, but does not mention any consideration of any other active approaches(i.e., backflushing). Was an active approach considered as a potential strategy or backup for addressing any issues?36.You stated that selected insulation will be replaced, and that this replacement willreduce the postulated post-accident debris loading effects on the sump strainer. Please discuss the insulation material being removed and the material that will replace theselected insulation, including debris generation and characteristics parameters of the replacement insulation. Has the new insulation been evaluated in the debris generation, transport, head loss analyses and other sump design analyses?37.You stated that for materials for which no ZOI values were provided in the NuclearEnergy Institute (NEI) guidance report "Pressurized Water Reactor Sump Performance Evaluation Methodology," NEI 04-07, or the associated NRC staff SE, conservative ZOIvalues are applied. Please provide a listing of the materials for which this ZOI approach was applied and the technical reasoning for concluding the value applied is conservative.38.You did not provide information on the details of the debris characteristics assumed intheir evaluations other than to state that the NEI and SE methodologies were applied. Please provide a description of the debris characteristics assumed in these evaluations and include a discussion of the technical justification for deviations from the SE-approved methodology.39.Has debris settling upstream of the sump strainer (i.e., the near-field effect) beencredited or will it be credited in testing used to support the sizing or analytical designbasis of the proposed replacement strainers? In the case that settling was credited foreither of these purposes, estimate the fraction of debris that settled and describe the analyses that were performed to correlate the scaled flow conditions and any surrogate debris in the test flume with the actual flow conditions and debris types in the plant's containment pool.40.Are there any vents or other penetrations through the strainer control surfaces whichconnect the volume internal to the strainer to the containment atmosphere above the containment minimum water level? In this case, dependent upon the containment pool height and strainer and sump geometries, the presence of the vent line or penetration could prevent a water seal over the entire strainer surface from ever forming; or else this seal could be lost once the head loss across the debris bed exceeds a certain criterion, such as the submergence depth of the vent line or penetration. According to Appendix A to Regulatory Guide 1.82, Revision 3, without a water seal across the entirestrainer surface, the strainer should not be considered to be "fully submerged."

Therefore, if applicable, explain what sump strainer failure criteria are being applied for the "vented sump" scenario described above.41.What is the basis for concluding that the refueling cavity drain(s) would not becomeblocked with debris? What are the potential types and characteristics of debris that could reach these drains? In particular, could large pieces of debris be blown into the upper containment by pipe breaks occurring in the lower containment, and subsequently drop into the cavity? In the case that large pieces of debris could reach the cavity, are trash racks or interceptors present to prevent drain blockage? In the case thatpartial/total blockage of the drains might occur, do water hold-up calculations used in the computation of NPSH margin account for the lost or held-up water resulting from debris blockage?42.What is the minimum strainer submergence during the postulated LOCA? At the timethat the re-circulation starts, most of the strainer surface is expected to be clean, and the strainer surface close to the pump suction line may experience higher fluid flow than the rest of the strainer. Has any analysis been done to evaluate the possibility of vortexformation close to the pump suction line and possible air ingestion into the ECCS pumps? In addition, has any analysis or test been performed to evaluate the possible accumulation of buoyant debris on top of the strainer, which may cause the formation of an air flow path directly through the strainer surface and reduce the effectiveness of the strainer?43.The September 2005 GL response stated that the licensee performed computationalfluid dynamics (CFD) analysis of which outputs included global (entire containment) and local (near sump pit) velocity contours, turbulent kinetic energy contours, path lines and flow distributions for various scenarios. Please explain how you used these outputs to determine the amount of debris that transports to the sump screen.