ML17053B130: Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(Created page by program invented by StriderTol)
Line 25: Line 25:
==1.0 INTRODUCTION==
==1.0 INTRODUCTION==


2.0 BENCHMARK VERIFICATION PROBLEMS-
===2.0 BENCHMARK===
VERIFICATION PROBLEMS-


==SUMMARY==
==SUMMARY==

Revision as of 06:08, 9 October 2018

Tmrsap Verification Analysis,Ofc of Nuclear Reactor Regulation Benchmark Problems, Books 1 & 2
ML17053B130
Person / Time
Site: Nine Mile Point Constellation icon.png
Issue date: 09/21/1979
From:
TELEDYNE ENGINEERING SERVICES
To:
Shared Package
ML17053B131 List:
References
NUDOCS 7910310290
Download: ML17053B130 (42)


Text

NIAGARA MOHAWK POWER CORPORATION 300 ERIE BOULEVARD WEST SYRACUSE, NY 13201%Ill"JJ YO PDItlTM WIlIKf FBINII I iIVM MLI<H fILh-ATTACHNENT"TO TES LETTER 3245A-4 BOOK 1 OF 2"TMRSAP" VERIFICATION ANALYSIS nunn

Dear uunov oonni ra~@Vl~t'~'I va~tvt~~tt tt'll\t t'IV~t t I tQ SEPTEMBER 21,

1979'VtI TELEDYNE ENGNEERIMQ SERVICES 303 BEAR HILL ROAD WALTHAM, MASSACHUSETTS 02154 w f g.617-890-3350 V9108X0~

P~0 Attachment to TES Letter 3245A-4<<TELEDYNE ENGINEERING SERVICES TABLE OF CONTENTS

1.0 INTRODUCTION

2.0 BENCHMARK

VERIFICATION PROBLEMS-

SUMMARY

OF RESULTS 2.1 Problem No.1-Hovgaard Bend 2.2 Prob 1 em No.2-Cof f ee Table'2.3 Problem No.3-Modified Reactor System 2.4 Problem No.323A-Piping System PAGE ,2'11 15 I

Attachment to TES Letter 3245A-4~$.W TELEDYNE ENGINEERING'ERVICES

1.0 INTRODUCTION

This report addresses the request by the Office of Nuclear Reactor Regulation (ONRR)for the verification of the Tt1RSAP comp~ter code.The information contained in this report satisfies the requirements of the computer code verification program as stated in IE Bulletin 79-07.Four benchmark problems defined by the ONRR were analyzed for linear elastic behavior.The structural models were subjected to dynamic loading induced by earthquake type excitation (seismic spectra)in three directions.

Dynamic solutions were determined by the modal.superposition and response spectrum method of seismic analysis, based on NRC Regulatory Guide 1.92.

Attachment to TES Letter 3245A-4-2-r<TELEDYNE ENGINEERING SERVICES 2.0 BENCHMARK VERIFICATION PROBLEMS-

SUMMARY

OF RESULTS 2.1'roblem No.1-Hov aard Bend The Hovgaard Bend configuration.was-modified slightly to accom-modate a modeling requirement for the TMRSAP computer code.The following computer generated plot shows the equivalent TMRSAP piping model for the Hovgaard Bend benchmark problem.A short segment of straight pipe was'dded to the model at the arc center of each bend to accoranodate an elbow-to-elbow connection.

This modeling resulted in slightly higher frequencies and corresponding modal participation.

I I Attachmont to TES Letter 324'5A-4 Ss TELEDYNE ENGINEERING

$ERyICES~LUHPED MASS SYSTEM FOR HOVGAARD BEND-BEHCHMARI'RQB.

NQ.1 Qio 0/I Pore: ClgC4E'0 A/PIV8'EiPS OZWINE'4&AKEiV7"S.

0

Attachment to TES Letter 3245A-4 W TELEDYNE ENGINEERING

$ERVICES BENCHMARK PROBLEM NO.1 HOVGAARD BEND MODE 1 2 3.4 5 FREQUENCIES CPS EPIPE 28.53 55.77 81.50 141.70 162.80 TMRSAP 28.53 55.79 81.48 141.70 162.8 MAXIMUM DISPLACEMENTS COMPONENT X U.U'x e 0 NODE 5 7 4 3 7 3 EPIPE 0.00784 0.00250 0.01745 0.00018 0.00021 0.00007 TNRSAP 0.010797 0.003453 0.024125 0.000255 0.000293 0.0000967 I ie Attachment to TES Letter 3245A-4-5-<<TELEDYNE ENGINEERING SERVICES BENCHMARK PROBLEM NO.1 HOVGAARD BEND MAXIMUM'ELEMENT LOADS COMPONENT Px(1)VY(I)vz(I)MY(I)Mz(I)TX(I)Px(J)-VY(J)vz(J)MV(~l}Mz(v)Tx(v)ELEMENT 7 1 10 10 1 3 7 1 10 an J\/8 1 EPIPE 28.1 36.4 34.8 1871.0 3227.0 629.6 26.7 36.4 34.8 npqa n I 1380.0 629.6 ELEMENT 8 1 12 12 1 3 9 1 12 I JC 10 1 TMRSAP 37.0 50.2 45.7 2561.0 4458.0 868.2 33.8~50.3 45.7'356.0'909.0 868.2 C

Attachment to-TES Letter 3245A-4-6-r>TELEDYNE ENGIREERIMG SERVlCES BENCHMARK PROBLEM NO.1 HOVGAARD BEND~GENERALIZED MODAL PARTICIPATION DIRECTION FACTORS: X=1.0, Y=0.6667, Z=1.0 E PIPE MODAL PARTICIPATION MODE 1 2 3 4 5'x 0.1752 0.3628-0.05397 0.08361-0.07925 P-0.02593-0.002074-0.2582-0.05268 0.06605 P-0.3308 0.1478-0.02793-0.01174-0.01115/P,.I D,.0.52328 0.51198 0.25404 0.13047 0.13473 TMRSAP MODAL PARTICIPATION MODE 1 2 3 4 5'x 0.1754 0.3628-.05405 0.08386-.07926 P-.02596.002035-.2582-.05280.06634-.3309.1479.02795-.01153-.01116 z PE xD~0.52360~0.51205 0.25414 0.13059 0.13465

Attachment to TES Letter 3245A-4 C><TELEDYNE ENGINEERING SERVICES 2.2 Problem No.2-Coffee Table A computer, generated isometric plot of Benchmark Problem No.2 is shown on the following page.The configuration for the TNRSAP computer code is the same as the EPIPE model with the exception of the element numbering..The element connectivity was defined differently for ease of input to'THRSAP.The results between Tt1RSAP and EPIPE are in excellent agreement as shown in the following tables which summarize the frequencies, maximum displacements and maximum element loads.

Attachment to'ES Letter 3245A-4-8-A TELEDYNE ENGINEERING SERVICES DYNAMI'C RESPONSE OF A COFFEE TABLE (RESPONSE SPECTRUM ANALYSISi OiB Q7 I2 l3 Qo Qw QI 0

Attachment to TES Letter 3245A-4-9-r<TELEDYNE ENGINEERING SERVICES BENCHMARK PROBLEM NO.2 COFFEE TABLE MODE 1 2-3 4 5 FREQUENCIES

('CPS)EPIPE 8.71 8.81 17.51 40.37 41.63 TMRSAP 8.71 8.804 17.50 40.36 41.62 MAX IMUM 0 I SPLACEMENTS COMPONENT (j x U U ex Oy ez NODE 11 13 13 3 14 4 EPIPE n nr~nn 0.00236 0.4464 0.00654 0.00001 0.00672 TRRSAP 0.46203 0.0023598 0.44691 0.006546 0.0000127 0.006722

Attachment to TES Letter 3245A-4-10-ENQINEERIRG SERVICES BENCHMARK PROBLEM NO.2 COFFEE TABLE MAXIMUM ELEMENT LOAOS COMPONENT Px(I)VY(I)Vz(I)MY(I)Mz(I)TX(I)Px(J)VY(J)vz(J)MY(V)-'Mz(v)Tx(v)ELEMENT 1 3 1 1 1'1 1 3 1 6'6 1 EPIPE 555.4 468.7 109.3 5229.0 5135.0 1.61 555.4 468.7 109.3 5229.0 513>.0 1.61 ELEMENT 1 3 1 1 1 1 1 3 1 6 6 1 TMRSAP.555.8 469.2 109.3 5230.0 5141.0 1.61 555.8 469.2 109.3 5230.0 5141.0-1.61 l~e Attachment to TES Letter 3245A-4-11-><TELEDYNE ENGINEERING SERVICES 2.3 Problem Ho.3-Modified Reactor S stem.The Modified Reactor System model was modified to accommodate elbow-to-elbow connections from the four corners of the model to the center point, node 8.The following computer generated plot shows the equivalent TMRSAP piping model for the Modified Reactor System.Each of the four outside loops (bend elements)were modeled as an equivalent series of three elements (tangent-bend-tangent).

The results between the TMRSAP and EPIPE computer codes are in good agreement as shown in the following tables which summarize the frequencies, maximum displacements, and maximum element loads.

~o J'p A TELEDYNE ENGINEERINQ SERVICES~: Attachment to TES Letter 3245A-4-12-Bl:HHARK j'ROBLEH NO.3 DYNAMIC RESPONSE OF R NODIFIED RERCTOR SYSTEN IB 0

~e Attachment to TES Letter 3245A-4-13--S<-TELEDYNE ENGINEERING SERVICE$NRC BENCHMARK PROBLEM NO.3 MODE 1 2 3 4 5 6 FREQUENCIES (CPS)EP IPE 1.806 1.875 3.205 3.480 3.539 3.645 TMRSAP 1.805 1.874 3.204 3.480 3.540 3.645 MAX IMUM.0 I SPLAC EMENTS COMPONENT X UZ e X ey ez NODE 13 13 13 12 13 EPIPE 5.32223 Vo V%00/5.39637 0.09062 0.00192 0.09036 TMRSAP~SRSS)'CLUSTER)4.5717, 6.2988 v.Oee5o 0.04908 4.7243 6.4084 0.07763 0.10689 0.001866 0.001968 0.07763 0.10689

~e Attachment to TES Letter 3245A-4 4k-14--r<-TELEDYNE ENQlMEERlNQ SERV)CES NRC BENCHMARK PROBLEM NO.3.MAXIMUM ELEMENT LOADS COMPONENT PX(I)VY(I)vz(I)TX(I)MY(I)Mz(,I)PX(V)VY(J)vz(J)TX(J)MY(C)Mz(c)ELEMENT NO.1 3 14 20 3 16 18 6 15 EPIPE (CLUSTER)3243.0 2109.0 635.0 4110.0 7823.0 971 AA A VPRNV~V I 3243.0 2109.0 930.0 3866.0 7891.0 14030.0 ELEMENT NO.1 20 3 25 14 6 13~SRSS 3028.0 2009.0 563.0 3596.0 7623.0 32570.0 3028.0 2009.0 430.0 3454.0 7611.0 10840.0 TMRSAP~CLUSTER 3574.0 2155.0 747.0 4592.0 8181.0 44140.0 3574.0 2155.0 590.0 4484.0, 8243.0 12070.0

~o Attachment to TES Letter 3245A-4-15-r>-TELEDYNE ENGINEERING SERVICES 2.4 Problem No.323A-Pi in System.The piping system defined in problem 323A was analyzed with the THRSAP computer code for each seismic spectra separately and the results of each response spectrum analysis were combined by taking the square root of the sum of the squares (SRSS)of corresponding maximum values of the spectrum response.The results of the maximum displacements are shown on the following pages arid they are in close agreement with the EPIPE results supplied by the NRC.The NRC supplied data for this benchmark problem did not include element loads;therefore, they are not summarized for this problem.

~e PIPING BENCH MARK PRQBLEM-323A T%6 O ID M ID 6 et 4J et MO Ol I I6 Pl~Pl g~z8 Pl~Sm Q V)Pl C 0 Pl 0)

~e Attachment to TES Letter 3245A-4-17-Ph TELEDYNE ENGlNEERlMQ SERVlcE$BENCHMARK PROBLEM NO.323A PIPING SYSTEM~e NODE 1 2 3-4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 FRE UENCIES (CPS)EP IPE 6.39 9.99 13.27 14.49 15.33 17.50 19.09 19.62 21.44 28.71 29.86 31.48 32.01 36.37 nn no~V~41.37 47.39 49.77 50.13 52.93 56.90 58.51 67.47 70.46 75.41 79.18 80.74 86.11 88.28 92.74 99.36 TMRSAP 6.39 9.99 13.27 14.49 15.33 17.50 19.09 19.63 21.44 28.71 29.87 31.49 32.01 36.37 41.37 47.40 49.77 50.13 52.94 56.91 58.52 67.47 70.'47 75.42 79.20 80.75.86.12 88.33 92.74 99.37

~o Attachment to o TES Letter 3245A-4-18-r<TELEDYNE ENGjNEERlNG SERVlCES NRC BENCHMARK PROBLEM 323A PIPING SYSTEM TMRSAP MAXIMUM DISPLACEMENTS uNODE 31 X-SPECTRA Y-SPECTRA Z-SPECTRA SRSS=SRSS.020751.0020513.010887.023523 CLUSTER.020785.0020675.010943.0235805 u>NODE 35 X-SPECTRA Y-SPECTRA Z-SPECTRA SRSS=.051633.057385..010441.077897.051638.057386.010448.077902 u NODE 36 X-SPECTRA Y-SPECTRA Z-SPECTRA SRSS=.013009.0028254.0068936.014991.013101.0028406.0069855.015116 e NODE 35 X-SPECTRA Y-SPECTRA Z-SPECTRA SRSS=.00021197.00023513.000043568

.00031955.00021198.00023518.000043607

.000319604 NODE 35 X-SPECTRA Y-SPECTRA Z-SPECTRA SRSS=.000084048

.000012717

.000043608

.000095565

.000084152

.000013047

.000043729

.000095728

~l T Attachment to TES Letter 3245A-4-19-r<TELEDYNE ENGINEER)NG SERVICES NRC BENCHMARK PROBLEM 323A PIPING SYSTEM MAXIMUM D ISPLACEMENTS eNODE 38 X-SPECTRA Y-SPECTRA Z-SPECTRA SRSS=SRSS.00020599.00022871.000042008

.00031065 CLUSTER.00020606.00022872.000042082

.00031071 n T%PI Al FMFhl)cl IMMARY COMPONENT x U UZ ex ey ez NODE 31 35 36 35 35 38 EPIPE 0.02354 0.07789 0.01500 0.00032 0.00010 0.00031 TNRSAP 0.02352 0.07789 0.01499 0.00032 0.000095 0.00031 NOTE: ELEMENT LOAD DATA WERE NOT SUPPLIED BY NRC.

I'A I,~o