ML072620462

Inservice Inspection Report, End of Cycle 18 Refueling Outage

ML072620462
Person / Time
Site:	McGuire
Issue date:	08/23/2007
From:	Gordon Peterson Duke Energy Carolinas, Duke Power Co
To:	Document Control Desk, Office of Nuclear Reactor Regulation
References
Download: ML072620462 (267)

Text

Duke GARY R. PETERSON R Power A Duke Energy Company Vice President McGuire Nuclear Station Duke Power MG01VP / 12700 Hagers Ferry Rd.

Huntersville, NC 28078-9340 704 875 5333 704 875 4809 fax grpeters@duke-energy.com August 23, 2007 U.S. Nuclear Regulatory Commission Attention: Document Control Desk Washington, D.C. 20555

Subject:

Duke Power Company LLC d/b/a Duke Energy Carolinas, LLC (Duke)

McGuire Nuclear Station, Unit 1 Docket Number 50-369 Inservice Inspection Report End of Cycle 18 Refueling Outage Attached is the Inservice Inspection Report for the end of cycle 18 (EOC-1 8) refueling outage for McGuire Nuclear Station (MNS), Unit 1. Attachment No. 1 is the Inspection Report performed in accordance with the Second outage of the Second Inspection Period of the Third 10-Year Inservice Inspection Interval.

No reportable indications were identified during this report period. Section 4.4 of the attached report lists the limited examination item numbers. A relief request will be submitted to the NRC for review and approval to address weld limitations found during this outage.

This letter and attachments do not contain any new NRC commitments.

Inquiries on this matter should be directed to K.L. Ashe at (704) 875-4535.

Sincerely, Gary R. Peterson www. dukepower.com

U.S. Nuclear Regulatory Commission Page 2 August 23, 2007

Attachment:

Inservice Inspections McGuire Unit 1 Refueling Outage 4/EOC 18 (Third Interval) xc (with attachment):

W.D. Travers U.S. Nuclear Regulatory Commission Regional Administrator, Region II Atlanta Federal Center 61 Forsyth St., SW, Suite 23T85 Atlanta, GA 30303 J.B. Brady Senior Resident Inspector (MNS)

U.S. Nuclear Regulatory Commission McGuire Nuclear Station J.F. Stang, Jr. (addressee only)

NRC Project Manager (CNS and MNS)

U.S. Nuclear Regulatory Commission Mail Stop 8 H4A Washington, D.C. 20555-0001

Attachment 1 Inservice Inspections McGuire Unit 1 Refueling Outage 4 / EOC 18 (Third Interval)

INSERVICE INSPECTION REPORT Duke Energy Carolinas McGuire Nuclear Station Unit 1 Eighteenth Refueling Outage Duke I Energy9

FORM NIS-1 OWNER'S DATA REPORT FOR INSER VICE INSPECTIONS As required by the Provisions of the ASME Code Rules

1. Owner:Duke Energy Carolinas, 526 S. Church St.. Charlotte, NC 28201-1006 (Name and Address of Owner)

2. Plant: McGuire Nuclear Station, 12700 Hagers Ferry Road Huntersville, N.C. 28078-9340 (Name and Address of Plant)

3. Plant Unit: 1 4. Owner Certificate of Authorization (if required) N/A

5. Commercial Service Date: December 1, 1981 6. National Board Number for Unit 44

7. Components Inspected:

Component or Manufacturer or Manufacturer or State or National Appurtenance Installer Installer Serial Province No. Board No.

No.

See Section 1.1 in the Attached Report Note: Supplemental sheets in the form of lists, sketches, or drawings may be used, provided (1) size is 81/2 in. x 11 in., (2) information in items 1 through 6 on this report is included on each sheet, and (3). each sheet is numbered and the number of sheets is recorded at the top of this form.

Total number of pages contained in this report 164.

OWNER'S REPORT FOR INSER VICE INSPECTIONS MCGUIRE UNIT 1 2007 REFUELING OUTAGE EOC 18 (OUTAGE 4)

Location: McGuire Nuclear Station 12700 Hagers Ferry Road Huntersville, North Carolina 28078-9340 NRC Docket No. 50-369 National Board No. 44 Commercial Service Date: December 1, 1981 Document Completion Date: Ag,,,,"o* Z 7 Owner: Duke Energy Carolinas 526 South Church St.

Charlotte, N. C. 28201-1006 Revision 0 Prepared By: Date 8-)3-2607 Reviewed By: Date ._/3 c! -7 Approved By: A;5"*- Date V 7

FORM NIS-1 (Back)

8. Examination Dates October 19, 2005 to May 28, 2007

9. Inspection Period Identification: Second Period

10. Inspection Interval Identification: Third Interval

11. Applicable Edition of Section XI 1998 Addenda 2000

12. Date/Revision of Inspection Plan: June 20, 2006 / Revision 2

13. Abstract of Examinations and Tests. Include a list of examinations and tests and a statement concerning status of work required for the Inspection Plan. See Sections 2.0, 3.0, and 6.0

14. Abstract of Results of Examinations and Tests. See Section 4.0, and 6.0

15. Abstract of Corrective Measures. See Section 4.3 We certify that a) the statements made in this report are correct b) the examinations and tests meet the Inspection Plan as required by the ASME Code,Section XI, and c) corrective measures taken conform to the rules of the ASME Code,Section XI.

Certificate of Authorization No. (if applicable) N/A __Expiration Date N/A___

Date "/d7 20 j Signed Duke Energy Carolinas By Owner CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State of Province of North Carolina employed by Hartford Steam Boiler of Connecticut (HSBCT) have inspected the components described in this Owners' Report during the period October 19, 2005 to May 28, 2007, and state that to the best of my knowledge and belief, the Owner has performed examinations and tests and taken corrective measures described in the Owners' Report in accordance with the Inspection Plan and as required by the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations, test, and corrective measures described in this Owners' Report.

Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or Sroperty damag, r a loss of any kind arising from or connected with this inspection

/0-Z,17 Commissions N.C. 1524 I,N National Board, State, Province, and Endorsements r Inýýýý Date August . 207 2007 HSBCT 200 Ashford Center North Suite 205 Atlanta, GA. 30338-4860 (800) 417-3721 www.hsbct.com

DISTRIBUTION LIST

1. Duke Energy Carolinas Nuclear Technical Services Division Section XI Inspection Program Section

2. Inspection and Welding Services (ISI Coordinator)

3. NRC Document Control Desk

4. HSBCT (AIA) c/o ANII at McGuire

5. State of North Carolina Department of Labor c/o J. M. Givens, Jr.

TABLE OF CONTENTS Section Title Revision 1.0 General Information 0 2.0 Third Ten-Year Interval Inspection Status 0 3.0 Final Inservice Inspection Plan 0 4.0 Results of Inspections Performed 0 5.0 Owner's Report for Repair / Replacement Activities 0 6.0 Pressure Testing 0

1.0 General Information This report describes the'lnservice Inspection of Duke Energy Corporation's McGuire Nuclear Station Unit 1 during Outage 4 / EOC 18. This is the second outage of the Second Inspection Period of the Third Ten-Year Interval. ASME Section XI, 1998 Edition through the 2000 Addenda was the governing Code for selection and performance of the ISI examinations.

Included in this report are: the inspection status for each examination category, the final inservice inspection plan, the inspection results for each item examined, and corrective action(s) taken when reportable conditions were found. In addition, there is an Owner's Report for the Repair / Replacement Section included for complete NIS-2 documentation of repairs and replacements.

1.1 Identification Numbers Manufacturer National Manufacturer or Installer State or Board Item or Installer Serial No. Province No. No.

Reactor Vessel Combustion CE67102 NC-178379 20766 Engineering Pressurizer Westinghouse 1471 NC-178395 68-123 Steam Generator 1A BWI 7701-04 NC-302668 157 Steam Generator 1B BWI 7693-01 NC-302669 146 Steam Generator 1C BWI 7701-03 NC-302670 155 Steam Generator 1D BWI 7701-02 NC-302671 154 Centrifugal Pacific Pumps 1A-48582 N/A 19 Charging Pump 1B-48583 22 Containment Spray Heat Delta Southern Co. 1A-35005-73-1 NC-147799 3394 Exchanger I B-35005-73-2 NC-147796 3395 Outage 4/EOC 18 Refueling Outage Report Page 1 of 6 McGuire Unit 1 Revision 0 Section 1 August 9, 2007

1.1 Identification Numbers Manufacturer National Manufacturer or Installer State or Board Item or Installer Serial No. Province No. No.

Excess Letdown Heat Atlas Industrial 1809 NC-1 87817 1554 Exchanger Manufacturing Company Letdown Heat Exchanger Joseph Oat & Sons, Inc. 2049-2A NC-187881 552 Reciprocating Charging Union Pump Company N721031B-603 N/A N/A Pump 1A 1-114E841G01 Reactor Coolant Pump Westinghouse 1B 2-114E841 G01 N/A N/A 1C 3-114E841 G01 1D 4-114E841G01 Reciprocating Charging Metal Bellows Company 74730-002 N/A 002 Pump Accumulator Reciprocating Charging Richmond Engineering N2409-10 N/A 75219 Pump Suction Stabilizer. Supply Co.

Residual Heat Joseph Oat & Sons, Inc. 1A-2046-2A NC-234202 635 Removal Heat 1B-2046-2A NC-234201 636 Exchanger Safety Injection Pump Pacific Pumps 1A-49355 N/A 80 1B-49356 81 Regenerative Heat Joseph Oat & Sons, Inc. 2047-2A NC-187897 595 Exchanger 596 597 Seal Water Heat Atlas Industrial 1766 NC 169797 1548 Exchanger Manufacturing Company Seal Water AMF Cuno 1A-13 N/A 3822 Injection Filter 1B-14 3823 Outage 4/EOC 18 Refueling Outage Report Page 2 of 6 McGuire Unit 1 Revision 0 Section 1 August 9, 2007

1.1 Identification Numbers Manufacturer National Manufacturer or Installer State or Board Item or Installer Serial No. Province No. No.

Main Steam Supply to Duke Power Co. SA N/A 4 Auxiliary Equipment System Containment Air Release Duke Power Co. VQ N/A 12 and Addition System Main Steam System Duke Power Co. SM N/A 17 Main Steam Vent to Duke Power Co. SV N/A 18 Atmosphere System Reactor Coolant System Duke Power Co. NC N/A 28 Liquid Waste Recycle Duke Power Co. WL N/A 29 System Refueling Water System Duke Power Co. FW N/A 31 Auxiliary Feedwater Duke Power Co. CA N/A 32 System Residual Heat Removal Duke Power Co. ND N/A 35 System Nuclear Service Water Duke Power Co. RN N/A 36 System Chemical & Volume Duke Power Co. NV N/A 37 Control System Component Cooling Duke Power Co. KC N/A 38 Systemn Main Feedwater System Duke Power Co. CF N/A 39 Containment Spray Duke Power Co. NS N/A 40 System Outage 4/EOC 18 Refueling Outage Report Page 3 of 6 McGuire Unit 1 Revision 0 Section 1 August 9, 2007

1.1 Identification Numbers Manufacturer National Manufacturer or Installer State or Board Item or Installer Serial No. Province No. No.

Containment Ventilation Duke Power Co. RV N/A 41 Cooling Water System Safety Injection System Duke Power Co. NI N/A 42 Containment Purge Duke Power Co. VP N/A 6 Ventilation Safety Injection Delta Southern Co. 41617-72-1 NC-178396 3038 Accumulator Tank 1A Safety Injection Delta Southern Co. 41617-72-2 NC-178397 3039 Accumulator Tank 1B Safety Injection Delta Southern Co. 41617-72-3 NC-178398 3040 Accumulator Tank 1C Safety Injection Delta Southern Co. 41617-72-4 NC-178399 3041 Accumulator Tank 1D Unit 1 Duke Power Co. N/A N/A 44 1.2 Personnel,Equipment and Material Certifications All personnel who performed or evaluated the results of inservice inspections during the time frame bracketed by the examination dates shown on the NIS-1 Form were certified in accordance with the requirements of the 1998 Edition of ASME Section XI with the 2000 Addenda including Appendix VII for ultrasonic inspections. In addition, ultrasonic examiners were qualified in accordance with ASME Section XI, Appendix VIII, and the 1998 Edition with the 2000 Addenda through the Performance Demonstration Initiative (PDI) for Supplements 2, 3, 4, 6, 8, and 10. Preservice examinations of weld overlays were conducted in accordance with Code Case N-504-2 including non-mandatory Appendix Q.

The appropriate certification records for each inspector, calibration records for inspection equipment, and records of materials used (i.e. NDE consumables) are on file at McGuire Nuclear Station or copies may be obtained by contacting Duke's Corporate Office in Charlotte, North Carolina.

Outage 4/EOC 18 Refueling Outage Report Page 4 of 6 McGuire Unit 1 Revision 0 Section 1 August 9, 2007

The copies of the certification records for the Washington Group International and Atlantic Group inspectors can be obtained by contacting Duke's Corporate Office in Charlotte, North Carolina.

1.3 Reference Documents The following reference documents apply to the inservice inspections performed during this report period. A copy may be obtained by contacting the ISI Plan Manager at Duke's Corporate Office in Charlotte, North Carolina:

1. Request for Relief (RFR) 01 -004 (Class 1, 2 and 3 snubber examination under station technical specification)

2. RFR 01-005 (Risk Informed Inservice Inspection Program Submittal)

3. RFR 01 -008 (Risk Informed ISI Alternative to Use VT-2 Instead of Volumetric Examination of Socket Welds)

4. Code Case N-460 (Alternative Examination Coverage For Class 1 and Class 2 Welds)

5. RFR-01-GO-002 to use Code Case N-416-2 "Alternative Pressure Test Requirement for Welded Repairs, Fabrication Welds for Replacement Parts and Piping Subassemblies, or Installation of Replacement Items by Welding, Class 1, 2 and 3 Section XI, Division 1."

1.4 Auamented and Elective Examinations Augmented and elective examination information found within this Inservice Inspection Report is not required by the ASME Section XI Code; therefore, it is exempt from ANII review, verification, and/or record certification.

Outage 4/EOC 18 Refueling Outage Report Page 5 of 6 McGuire Unit 1 Revision 0 Section 1 August 9, 2007

1.5 Responsible Inspection Agency Hartford Steam Boiler of Connecticut (HSBCT) is responsible for the third party inspections required by ASME Section XI.

Authorized Nuclear Inservice Inspector(s)

Name: Jerome F. Swan Employer: HSBCT Business 200 Ashford Center North Address: Suite 205 Atlanta, GA 30338-4860 (800) 417-3721 www.hsbct.com Outage 4/EOC 18 Refueling Outage Report Page 6 of 6 McGuire Unit 1 Revision 0 Section 1 August 9, 2007

2.0 Third Ten-Year Interval Inspection Status The completion status of inspections required by the 1998 ASME Code Section Xl through the 2000 Addenda is summarized in this section. The requirements are listed by the ASME Section XI Examination Category as defined in Table IWB-2500-1 for Class 1 Inspections, Table IWC-2500-1 for Class 2 Inspections and IWF-2500-1 for Class 1, 2, and 3 Component Supports. Augmented, Elective, and Risk Informed inspections are also included.

During the McGuire Third 10 Year Interval, piping welds will be examined under the Risk Informed Inservice Inspection Program developed in accordance with methodology contained in the Westinghouse Owner's Group (WOG) Topical Report, WCAP-14572, Revision 1-NP-A. Request for Relief 01-005 was submitted to the NRC seeking approval to incorporate the Risk Informed Program into the Third 10 Year Interval ISI Plan for McGuire Unit 1. The NRC approved use of this program per SER dated June 12, 2002. Previous code Examination Categories B-F, B-J, C-F-i, and C-F-2 will now be combined under the new Risk Informed Category R-A.

Class 1 Inspections Examination Description Inspections Inspections 6 Percentage Deferral Category Required Completed Completed Allowed B-A Pressure Retaining Welds 28 8 28.57% Yes in Reactor Vessel B-B Pressure Retaining Welds 5 3 60.00% No in Vessels Other than Reactor Vessel B-D Full Penetration Welded 36 12 33.33% Partial Nozzles in Vessels Inspection Program B B-F Pressure Retaining Reference Dissimilar Metal Welds in Risk Vessel Nozzles Informed Program R01. Items B-G-1 Pressure Retaining Bolting 243 151 62.13% No Greater than 2" in Diameter Outage 4/EOC 18 Refueling Outage Report Page 1 of 5 McGuire Unit 1 Revision 0 Section 2 August 9, 2007

Class 1 Inspections 6

Examination Description Inspections Inspections Percentage Deferral Category Required Completed Completed Allowed B-G-2 Pressure Retaining 17 9 52.94% No Bolting 2" and Less in Diameter B-J Pressure Retaining Welds Reference in Piping Risk Informed Program R01. Items B-K Welded Attachments for 6 4 66.66% No Piping, Pumps and Valves B-L-1 Pressure Retaining Welds N/A N/A N/A Yes in Pump Casings B-L-2 Pump Casings 1 0 0.00% Yes B-M-1 Pressure Retaining N/A N/A N/A Yes Welds in Valve Bodies B-M-2 Valve Body > 4 in. 8 4 50.00% Yes Nominal Pipe Size B-N-1 Interior of Reactor Vessel 3 2 66.66% No B-N-2 Integrally Welded Core Support Structures and 2 0 0.00% Yes Interior Attachments to Reactor Vessels B-N-3 Removable Core Support 1 0 0.00% Yes Structures B-0 Pressure Retaining Welds 3 2 66.66% Yes in Control Rod Housings Outage 4/EOC 18 Refueling Outage Report Page 2 of 5 McGuire Unit 1 Revision 0 Section 2 August 9, 2007

Class 1 Inspections 6

Examination Description Inspections Inspections Percentage Deferral Category Required Completed Completed Allowed B-P All Pressure Retaining REFERENCE SECTION 6.0 OF THIS REPORT Components B-Q, Steam Generator Tubir F-A Class 1 Component F01.010 Supports Note: Steam Generator Tubing is examined and documented by the Metallurgy and Lab Services Section/Nuclear Technical Services Division as required by the Station Technical Specifications and is not included in this report.

6 Deferral of inspection to the end of the interval as allowed by ASME Section XI Tables IWB 2500-1.

These examination categories are exempt from percentage requirements per IWB-2412 (a),

Inspection Program B.

Outage 4/EOC 18 Refueling Outage Report Page 3 of 5 McGuire Unit 1 Revision 0 Section 2 August 9, 2007

Class 2 Inspections Examination 6 Description Inspections Inspections Percentage Deferral Category Required Completed Completed Allowed C-A Pressure Retaining Welds 26 8 30.76% No in Pressure Vessels C-B Pressure Retaining Nozzle 9 4 44.44% No Welds in Vessels C-C Integral Attachments for 33 16 48.48% No Vessels, Piping, Pumps and Valves C-D Pressure Retaining Bolting N/A N/A N/A N/A Greater Than 2" in Diameter C-F-1 Pressure Retaining Welds Reference in Austenitic Stainless Risk Informed Steel or High Alloy Piping Program R01.

Items C-F-2 Pressure Retaining Welds Reference in Carbon or Low Alloy Risk Informed Steel Piping Program R01.

Items C-G Pressure Retaining Welds 3 2 66.66% No in Pumps and Valves C-H All Pressure Retaining REFERENCE SECTION 6.0 OF THIS REPORT Components F-A Class 2 Component 233 124 53.21% No F01.020 Supports Additional Component Support Examinations Class 1, 2 & 3 Examination 6 Description Inspections Inspections Percentage Deferral Category Required Completed Completed Allowed F-A Supports other than Piping 47 32 68.08% No F01.040 Supports Class 1,2& 2_3 F01.050 Component Supports, No Snubbers Class 1, 2 & 3 6Deferral of inspection to the end of the interval as allowed by ASME Section XI Tables IWB-2500-1 and IWC-2500-1.

• Examinations to be performed per Request for Relief 01-004.

Outage 4/EOC 18 Refueling Outage Report Page 4 of 5 McGuire Unit 1 Revision 0 Section 2 August 9, 2007

Risk Informed Inservice Inspection Program Class 1 and 2 Examination Description Inspections Inspections Percentage 6Deferral Category Required Completed Completed Allowed Piping Examinations R-A Class 1 and 2 Section 97 48 49.48% No Augmented / Elective Inspections Augmented and elective examination information found within this Inservice Inspection Report is not required by the ASME Section XI Code; therefore, it is exempt from ANII review, verification, and/or record certification.

Summary Description PercentageComplete Number M1.G3 Pipe Rupture Protection No examinations required for Outage 4 / EOC-18 M1 .G4.1 Reactor Vessel Head to Pipe Welds No Examinations required for Outage 4 / EOC-18 M1 .G5.1 Reactor Vessel Head Exams - VT-2 and UT Per NRC Order 100% of Outage 4 / EOC-18 EA-03-009 Requirements Met M1 .G5.2 Reactor Vessel Vent Line - UT per NRC Order EA-03-009, 100% of Outage 4 / EOC-18 PT per NRC Order EA-03-009, VT-2 every 4 refueling Requirements Met outages or 7years per NRC Order EA-03-009, and VT-2 I every 3 refueling outages per MRP-139 M1.G5.3 Bare Metal Inspections of the Reactor Vessel Primary 100% of Outage 4 / EOC-18 Nozzles per MRP-1 39 Requirements Met M1.G6.1 Bare Metal Visual Inspection of the Pressurizer Welds per 100% of Outage 4 / EOC-18 MRP-139 Requirements Met M1 .G6.2 Bare Metal Visual Inspection of the Pressurizer Manway 100% of Outage 4 / EOC- 18 Diaphram Seal Weld per NRC Bulletin 2004-01 Requirements Met M1.H1 Reactor Vessel UHI Welds - RPV Head to UHI Tube / UHI 100% of Outage 4 / EOC-18 End Cap to Pipe (Elective) Requirements Met Outage 4/EOC 18 Refueling Outage Report Page 5 of 5 McGuire Unit 1 Revision 0 Section 2 August 9, 2007

3.0 FinalInservice Inspection Plan The final Inservice Inspection Plan shown in this section lists all ASME Section Xl Class 1, Class 2, Class 3, Augmented, and Risk Informed examinations credited for this report period.

The information shown below is a field description for the reporting format included in this section of the report:

ITEM NUMBER = ASME Section XI Tables IWB-2500-1 (Class 1), IWC-2500-1 (Class 2), IWF-2500-1 (Class 1 and Class 2 ), Augmented, and Risk Informed Requirements ID NUMBER = Unique Identification Number SYS = Component System Number ISO/DWG NUMBERS = Location and/or Detail Drawings PROC = Examination Procedures INSP REQ. - Examination Technique - Magnetic Particle, Dye Penetrant, etc.

MAT / SCH = General Description of Material DIA / THICK = Diameter/Thickness CAL BLOCKS = Calibration Block Number COMMENTS - General and/or Detail Description Outage 4/EOC 18 Refueling Outage Report Page 1 of 1 McGuire Unit 1 Revision 0 Section 3 August 9, 2007

DUKE ENERGY QUALITY ASSURANCE CHNICAL SERVICES Inservice Inspection DatabaseManagement System Plan Report McGuire 1, 3rd Interval, Outage 4 (EOC-18)

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

Summary Num Insp Component ID / Type System ISOIDWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Category AUG M1 .G5.1.0001 G05.001.001, GO5.001.002 RPV-HEAD-PEN NC MC-ISIN3-1553-01.00 54-1SI- UT CS-Inconel 0.000 / 0.000 FOR VISUAL EXAMINATION (VT-2): BARE METAL 603-000 VISUAL EXAMINATION OF 100% OF THE REACTOR Circumferential Class 1 MCM 1201.01-0186 PRESSURE VESSEL HEAD SURFACE (INCLUDING 360 DEGREES AROUND EACH RPV HEAD PENETRATION NOZZLE). MP/0/7150/153 RX VESSEL HEAD PENETRATION VISUAL INSPECTION. TO BE DONE EVERY THREE REFUELING OUTAGES OR FIVE YEARS. (FOR RESPONSIBLE INDIVIDUAL CONTACT J.M.

SHUPING AND REACTOR VESSEL ENGINEERING/

MATERIALS ENGINEERING GROUP. REFERENCE NRC ORDER EA-03-009 INSPECT DURING THIRD INTERVAL 1EOC-18 AND 1EOC-21 INSPECT DURING FOURTH INTERVAL 1EOC-24, 1EOC-27 AND FIFTH INTERVAL 1EOC-30.

FOR UT EXAMINATION: RPV HEAD PENETRATION NOZZLES (NOZZLE BASE MATERIAL) FROM TWO INCHES ABOVE J-GROOVE WELD TO THE BOTTOM OF THE NOZZLE. VENDOR AND SPECIAL EQUIPMENT REQUIRED. TO BE DONE WITHIN FIVE YEARS OF 2/11/2003 AND EVERY FOUR REFUELING OUTAGES OR SEVEN YEARS WHICHEVER COMES FIRST. (FOR RESPONSIBLE INDIVIDUAL CONTACT J.M. SHUPING AND REACTOR VESSEL ENGINEERING/MATERIALS ENGINEERING GROUP. REFERENCE NRC ORDER EA-03-009, INSPECT DURING THIRD INTERVAL 1EOC-18. INSPECT DURING FOURTH INTERVAL 1EOC-22, 1 EOC-26 AND FIFTH INTERVAL 1EOC-30, BARE METAL VISUAL EXAMINATION OF 100- OF THE REACTOR PRESSURE VESSEL HEAD SURFACE (INCLUDING 360 DEGREES AROUND EACH RPV HEAD PENETRATION NOZZLE).

MP/0/7150/153 RX VESSEL HEAD PENETRATION VISUAL INSPECTION. TO BE DONE EVERY THREE REFUELING OUTAGES OR FIVE YEARS. (FOR RESPONSIBLE INDIVIDUAL CONTACT J.M.

SHUPING AND REACTOR VESSEL ENGINEERING/MATERIALS ENGINEERING GROUP.

REFERENCE NRC ORDER EA-03-009.

Printed 8/6/2007 9:31:53 AM GJUB302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page lof26

This report Includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd lntern itage 4 (EOC-18)

Summary Nh.. Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / Historical Data Catecori AUG M1 .G5.1.0001 G05.001.001, G05.001.002 RPV-HEAD-PEN NC MC-ISIN3-1553-01.00 NDE-68 VT-2 CS-Inconel 0.000 / 0.000 FOR VISUAL EXAMINATION (VT-2): BARE METAL Circumferential Class 1 MCM 1201.01-0186 VISUAL EXAMINATION OF 100% OF THE REACTOR PRESSURE VESSEL HEAD SURFACE (INCLUDING 360 DEGREES AROUND EACH RPV HEAD PENETRATION NOZZLE). MP/0/7150/153 RX VESSEL HEAD PENETRATION VISUAL INSPECTION. TO BE DONE EVERY THREE REFUELING OUTAGES OR FIVE YEARS. (FOR RESPONSIBLE INDIVIDUAL CONTACT J.M.

SHUPING AND REACTOR VESSEL ENGINEERING/

MATERIALS ENGINEERING GROUP. REFERENCE NRC ORDER EA-03-009 INSPECT DURING THIRD INTERVAL 1EOC-18 AND 1 EOC-21 INSPECT DURING FOURTH INTERVAL 1EOC-24, 1EOC-27 AND FIFTH INTERVAL 1EOC-30.

FOR UT EXAMINATION: RPV HEAD PENETRATION NOZZLES (NOZZLE BASE MATERIAL) FROM TWO INCHES ABOVE J-GROOVE WELD TO THE BOTTOM OF THE NOZZLE. VENDOR AND SPECIAL EQUIPMENT REQUIRED. TO BE DONE WITHIN FIVE YEARS OF 2/11/2003 AND EVERY FOUR REFUELING OUTAGES OR SEVEN YEARS WHICHEVER COMES FIRST. (FOR RESPONSIBLE INDIVIDUAL CONTACT J.M. SHUPING AND REACTOR VESSEL ENGINEERING/MATERIALS ENGINEERING GROUP. REFERENCE NRC ORDER EA-03-009, INSPECT DURING THIRD INTERVAL 1EOC-18. INSPECT DURING FOURTH INTERVAL 1EOC-22, 1EOC-26 AND FIFTH INTERVAL 1EOC-30, BARE METAL VISUAL EXAMINATION OF 100- OF THE REACTOR PRESSURE VESSEL HEAD SURFACE (INCLUDING 360 DEGREES AROUND EACH RPV HEAD PENETRATION NOZZLE).

MP/0/7150/153 RX VESSEL HEAD PENETRATION VISUAL INSPECTION. TO BE DONE EVERY THREE REFUELING OUTAGES OR FIVE YEARS. (FOR RESPONSIBLE INDIVIDUAL CONTACT J.M.

SHUPING AND REACTOR VESSEL ENGINEERING/MATERIALS ENGINEERING GROUP.

REFERENCE NRC ORDER EA-03-009.

SDQA Cat 'C" McGuire 1 8/6/2007 9:29:23 AM Page 20126 Printed ~/~/2UUt t~'nntea 9:31:53 AM 8/6/2007 ~i1~b~i AM UJU~iU~ v. UI/02/U(

GJU8302 V. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 2 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Inter utage 4 (EOC-18)

Summary Nub.... Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData C~teQ2rM AUG Ml .G5.2.0001 --

1 RPV-VENT-NOZZLE NC 54-ISI- UT Inconel 0.000 / 0.000 M1.G5.2.0001 RPV Vent Line Nozzle to Head Weld.

605-000 (UT) Ultrasonically examine from under the RPV Class Head. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group).

Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval)

RPV Vent Line Nozzle to Head Weld, (VT-2) Bare Metal Visual examine at the RPV Head to interrogate the vent line annulus. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every 3 (3) refueling outages. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Engineering/Materials Group). Inspect during Inspect during EOC-18 and EOC-21 (3rd Interval), EOC-24, EOC-27 and EOC-30 (4th Interval) (MRP-139 Requirements)

(MP/O/A/7150/153 RX Vessel Head Bare Metal Inspection Procedure to be used).

RPV Vent Line Nozzle to Head Weld. (PT) Dye Penetrant Test from under the RPV Head.

Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group). Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval).

RPV Vent Line Nozzle to Head Weld. (VT-2) Bare Metal Printed 8/6/2007 9:31:53 AM GJUS302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 3 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGulre 1, 3rd Intern utage 4 (EOC-18)

Summary Nu,... Insp Component ID / Type System ISOIDWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData CateoQor AUG Visual examine at the RPV Head to interrogate the vent line annulus from above the head. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. Iftime between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group). Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval).

(MP/0/A/7150/153 RX Vessel Head Bare Metal Inspection Procedure to be used).

GJU8302 v. SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 4 of 26 Printed 9:31:53 AM 8/6/2007 9:31:53 Printed 8/6/2007 AM GJU8302 v. 07/02/07 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 4 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd lnterv itage 4 (EOC.18)

Summary Num Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Category AUG M1 .G5.2.0001 1RPV-VENT-NOZZLE NC 54-PT- PT Inconel 0.000 / 0.000 M1.G5.2.0001 RPV Vent Line Nozzle to Head Weld.

200-06 (UT) Ultrasonically examine from under the RPV Class Head. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened, If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group).

Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval)

RPV Vent Line Nozzle to Head Weld. (VT-2) Bare Metal Visual examine at the RPV Head to interrogate the vent line annulus. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every 3 (3) refueling outages. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Engineering/Materials Group). Inspect during Inspect during EOC-18 and EOC-21 (3rd Interval), EOC-24, EOC-27 and EOC-30 (4th Interval) (MRP-139 Requirements)

(MP/0/A/7150/153 RX Vessel Head Bare Metal Inspection Procedure to be used).

RPV Vent Line Nozzle to Head Weld. (PT) Dye Penetrant Test from under the RPV Head.

Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group). Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Inlerval), EOC-26 and FOC-30 (4th )nterval).

RPV Vent Line Nozzle to Head Weld. (VT-2) Bare Metal Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SUDJA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 5 of 26

I his report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interu 'itage 4 (EOC-18)

Summary Nu. Insp Component ID / Type System ISOIDWG Numbers Procedure Req Mat Sched ThickWDia Cal Blocks Comments / HistoricalData AU__

G Visual examine at the RPV Head to interrogate the vent line annulus from above the head. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group). Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval).

(MP/0/A/7150/153 RX Vessel Head Bare Metal Inspection Procedure to be used).

Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 6 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Inter, utage 4 (EOC-18)

Summary Nui. Insp Component ID / Type System ISOIDWG Numbers Procedure Req Mat Sched ThicklDia Cal Blocks Comments / HistoricalData AUG AUtg Ml .G5.2.0001 1RPV-VENT-NOZZLE NC MP\0\A\71 VT-2 Inconel 0.000 / 0.000 M1.G5.2.0001 RPV Vent Line Nozzle to Head Weld.

50-153 (UT) Ultrasonically examine from under the RPV Class Head. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group).

Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval)

RPV Vent Line Nozzle to Head Weld. (VT-2) Bare Metal Visual examine at the RPV Head to interrogate the vent line annulus. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every 3 (3) refueling outages. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Engineering/Materials Group). Inspect during Inspect during EOC-18 and EOC-21 (3rd Interval), EOC-24, EOC-27 and EOC-30 (4th Interval) (MRP-139 Requirements)

(MP/0/A/7150/153 RX Vessel Head Bare Metal Inspection Procedure to be used).

RPV Vent Line Nozzle to Head Weld. (PT) Dye Penetrant Test from under the RPV Head.

Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group). Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th tntervat).

RPV Vent Line Nozzle to Head Weld. (VT-2) Bare Metal Printe ..

/6.007..3 .: .. AM....... .. ... /7....at...cu.. . /62079:923AP ge7of2 Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDOA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 7 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Intern utage 4 (EOC-18)

Summary Nut,- Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Catecor AUG Visual examine at the RPV Head to interrogate the vent line annulus from above the head. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group). Reference NRC Order EA-03-009. Inspect during EOC-1 8 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval).

(MP/Q/A/7150/153 RX Vessel Head Bare Metal Inspection Procedure to be used).

McGuire 1 8/6/2007 g:29:23 AM Page 8 of 26

-'rlniea wt~i~uu Printed MM UJUd~jU~

i]:~xj AM 8/6/2007 9:31:53 GJUS302 v.

v. uiu~iu 07/02107 Cat "C" SDQA Cat SLX1A "C" McGuire 1 8/6/2007 9:29:23 AM Page 8 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Inter, Wtage 4 (EOC-18)

Summary Nuni Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData AUG AU___.

M1 .G5.2.0001 1RPV-VENT-NOZZLE NC MP\0\A\71 VT-2 Inconel 0.000 / 0.000 M1.G5.2.0001 RPV Vent Line Nozzle to Head Weld.

50-153 (UT) Ultrasonically examine from under the RPV Class Head. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group).

Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval)

RPV Vent Line Nozzle to Head Weld. (VT-2) Bare Metal Visual examine at the RPV Head to interrogate the vent line annulus. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every 3 (3) refueling outages. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Engineering/Materials Group). Inspect during Inspect during EOC-18 and EOC-21 (3rd Interval), EOC-24, EOC-27 and EOC-30 (4th Interval) (MRP-139 Requirements)

(MP/0/A/7150/153 RX Vessel Head Bare Metal Inspection Procedure to be used).

RPV Vent Line Nozzle to Head Weld. (PT) Dye Penetrant Test from under the RPV Head.

Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections ma'y be shortened, but not *e*nghened. ý1 time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group). Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval).

RPV Vent Linre Nozzle to Head Weld. (VT-2) Bare Metal Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 9 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Intert 'wtage4 (EOC-18)

Summary Nui. insp Component ID / Type System ISOIDWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Categ2rx AUG Visual examine at the RPV Head to interrogate the vent line annulus from above the head. Examinations to be done within (5) years of 2/11/2003, and thereafter at least every four (4) refueling outages or seven (7) years, whichever occurs first. The inspections will begin in EOC-18. Time between inspections may be shortened, but not lengthened. If time between inspections is shortened, next inspection will occur at frequencies stipulated above. Vendor and special equipment required. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Engineering/Materials Group). Reference NRC Order EA-03-009. Inspect during EOC-18 and EOC-22 (3rd Interval), EOC-26 and EOC-30 (4th Interval).

(MP/0/A/7150/153 RX Vessel Head Bare Metal Inspection Procedure to be used).

Ml .G5.3,0001 1RPV3-445E-SE NC NDE-68 VT-2 Inconel 0.000 / 0.000 34.062" RV Primary Outlet Nozzle Weld and Butter.

Class (VT-2) Bare Metal Visual examination of RV Outlet Nozzles. Bare Metal Visual each RFO except outages in which volumetric exams are being conducted. This exam will begin in EOC-18. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-18, EOC-19, EOC-20, EOC-21 (3rd Interval) EOC-22, EOC-23, EOC-24, EOC-25, EOC-26, EOC-27 and EOC-28 (4th Interval). (Per MRP-139) 34.062" RV Primary Outlet Nozzle Weld and Butter.

(UT) Volumetric examination of RV Outlet Nozzles.

Volumetric examinations every 5 years starting with EOC-19. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-19 (3rd Interval) EOC-22, EOC-25 and EOC-28 (4th Interval).

Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 -§DQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 10 of 26

This report Includes all changes through addendum 1 MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Intery stage 4 (EOC-18)

Summary Nunt lnsp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData CateOr' AUG Ml .G5.3.0002 1RPV3-445F-SE NC NDE-68 VT-2 Inconel 0.000 / 0.000 34.062" RV Primary Outlet Nozzle Weld and Butter.

Class (VT-2) Bare Metal Visual examination of RV Outlet Nozzles. Bare Metal Visual each RFO except outages in which volumetric exams are being conducted. This exam will begin in EOC-18. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-18, EOC-19, EOC-20, EOC-21 (3rd Interval) EOC-22, EOC-23, EOC-24, EOC-25, EOC-26, EOC-27 and EOC-28 (4th Interval). (Per MRP-139) 34.062" RV Primary Outlet Nozzle Weld and Butter.

(UT) Volumetric examination of RV Outlet Nozzles.

Volumetric examinations every 5 years starting with EOC-19. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-19 (3rd Interval) EOC-22, EOC-25 and EOC-28 (4th Interval).

Ml .G5.3.0003 --

1RPV3-445G-SE NC NDE-68 VT-2 Inconel 0.000 / 0.000 34.062" RV Primary Outlet Nozzle Weld and Butter.

Class (VT-2) Bare Metal Visual examination of RV Outlet Nozzles. Bare Metal Visual each RFO except outages in which volumetric exams are being conducted. This exam will begin in EOC-18. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-18, EOC-19, EOC-20, EOC-21 (3rd Interval) EOC-22, EOC-23, EOC-24, EOC-25, EOC-26, EOC-27 and EOC-28 (4th Interval). (Per MRP-139).

34.062" RV Primary Outlet Nozzle Weld and Butter.

(UT) Volumetric examination of RV Outlet Nozzles.

Volumetric examinations every 5 years starting with EOC-19. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-19 (3rd Interval) EOC-22, EOC-25 and EOC-28 (4th Interval).

SDQA Cat "C" MoGuire 1 8/6/2007 9:29:23AM Page 11 of 26 Printed 8/6/2007 Printed AM GJUB3O2 9:31:53 AM 8/6/2007 9:31:53 v. 07/02/07 GJI-18302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page I I of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv "tage 4 (EOC-18)

Summary Nun, Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments /Historical Data Category AUG Ml .G5.3.0004 1RPV3-445H-SE NC NDE-68 VT-2 Inconel 0.000 / 0.000 34.062" RV Primary Outlet Nozzle Weld and Butter.

Class (VT-2) Bare Metal Visual examination of RV Outlet Nozzles. Bare Metal Visual each RFO except outages in which volumetric exams are being conducted. This exam will begin in EOC-18. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-18, EOC-19, EOC-20, EOC-21 (3rd Interval) EOC-22, EOC-23, EOC-24, EOC-25, EOC-26, EOC-27 and EOC-28 (4th Interval). (Per MRP-139).

34.062" RV Primary Outlet Nozzle Weld and Butter.

(UT) Volumetric examination of RV Outlet Nozzles.

Volumetric examinations every 5 years starting with EOC-19. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-19 (3rd Interval) EOC-22, EOC-25 and EOC-28 (4th Interval).

Ml .G5.3.0005 1RPV3-445A-SE NC NDE-68 VT-2 Inconel 0.000 / 0.000 32.5" RV Primary Inlet Nozzle Weld and Butter. (VT-2)

Class Bare Metal Visual examination of RV Inlet Nozzles.

Bare Metal Visual once every 3 RFO's except outages in which volumetric exams are being conducted. This exam will begin in EOC-18. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-18 and EOC-21, EOC-24, EOC- 27, and EOC-30 (4th Interval).

32.5" RV Primary Inlet Nozzle Weld and Butter. (UT)

Volumetric examination of RV Inlet Nozzles.

Volumetric examinations every 6 years starting with EOC-20. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-20 (3rd Interval), EOC-24, EOC-27 EOC-30 4th (Interval).

-'rintea dI~I2~~( ~1 bj AMAM GJU8302 U(/U2/IJJ

v. 07/02/07 uuu~ju~ v. SVQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 12 of 26 Printed 8/6/2007 9:31:53 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 12 of 26

This report Includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the Issued plan.

McGuire 1, 3rd Interv *tage 4 (EOC-18)

Summary Nuir Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched ThickiDia Cal Blocks Comments / HistoricalData Category AUG M1 .G5.3.0006 1 RPV3-445B-SE NC NDE-68 VT-2 Inconel 0.000 / 0.000 32.5" RV Primary Inlet Nozzle Weld and Butter. (VT-2)

Class Bare Metal Visual examination of RV Inlet Nozzles.

Bare Metal Visual once every 3 RFO's except outages in which volumetric exams are being conducted. This exam will begin in EOC-18. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-18 and EOC-21, EOC-24, EOC- 27, and EOC-30 (4th Interval).

32.5" RV Primary Inlet Nozzle Weld and Butter. (UT)

Volumetric examination of RV Inlet Nozzles.

Volumetric examinations every 6 years starting with EOC-20. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-20 (3rd Interval), EOC-24, EOC-27 EOC-30 4th (Interval).

M1 .G5.3.0007 1RPV3-445C-SE NC NDE-68 VT-2 Inconel 0.000 / 0.000 32.5" RV Primary Inlet Nozzle Weld and Butter. (VT-2)

Class Bare Metal Visual examination of RV Inlet Nozzles.

Bare Metal Visual once every 3 RFO's except outages in which volumetric exams are being conducted. This exam will begin in EOC-18. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-18 and EOC-21, EOC-24, EOC- 27, and EOC-30 (4th Interval).

32.5" RV Primary Inlet Nozzle Weld and Butter. (UT)

Volumetric examination of RV Inlet Nozzles.

Volumetric examinations every 6 years starting with EOC-20. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-20 (3rd Interval), EOC-24, EOC-27 EOC-30 4th (Interval).

McGuire 1 8/6/2007 9:29:23 AM Page 13 of 26 Printed 8/6/2007 Printed 9:31:53 AM 8/6/2007 9:31:53 GJU8302 AM GJU8302 v. 07/02/07

v. 07/02/07 Cat "C" SDQA Cat SDQA "C" McGuire 1 8/6/2007 9:29:23 AM Page 13 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv: ;tage 4 (EOC-18)

Summary Num,, Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched ThicWlDia Cal Blocks Comments / Historical Data Catealory AUG M1 .G5.3.0008 1 RPV3-445D-SE NC NDE-68 VT-2 Inconel 0.000 / 0.000 32.5" RV Primary Inlet Nozzle Weld and Butter. (VT-2)

Class Bare Metal Visual examination of RV Inlet Nozzles.

Bare Metal Visual once every 3 RFO's except outages in which volumetric exams are being conducted. This exam will begin in EOC-18. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M.

Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-18 and EOC-21, EOC-24, EOC- 27, and EOC-30 (4th Interval).

32.5" RV Primary Inlet Nozzle Weld and Butter. (UT)

Volumetric examination of RV Inlet Nozzles.

Volumetric examinations every 6 years starting with EOC-20. Inspect per requirements of MRP-139. (For responsible Individual, contact J.M. Shuping and Reactor Vessel Enginerring/Materials Group). Inspect during EOC-20 (3rd Interval), EOC-24, EOC-27 EOC-30 4th (Interval).

M1 .G6.1.0001 1PZR-W1SE NC MCM 1.201.01-0140 002 NDE-68 VT-2 CS-Inconel 0.000 /0.000 (VT-2) Bare Metal Visual examination of Pressurizer Class MCM 1201.01-0186 Welds.

Surge Nozzle to Safe End Weld 1PZR-WISE Ml .G6.1.0002 1PZR-W3SE NC MCM 1201.01-0170 001 NDE-68 VT-2 (VT-2) Bare Metal Visual examination of Pressurizer Class Welds.

PZR Relief Nozzle to Safe End Weld 1 PZR-W3SE M1 .G6.1.0003 1PZR-W4ASE NC MCM 1201.01-0170 001 NDE-68 VT-2 (VT-2) Bare Metal Visual examination of Pressurizer Class Welds.

PZR Safety Nozzle to Safe End Weld 1PZR-W4ASE Ml .G6.1.0004 1PZR-W4BSE NC MCM 1201.01-0170 001 NDE-68 VT-2 (VT-2) Bare Metal Visjal examination of Pressurizer Welds.

Class PZR Safety Nozzle to Safe End Weld SPZR-W4BSE Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 14 of 26

This report includes all changes through addendum 1 MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv. ,tage 4 (EOC-18)

Summary Nt.. Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Categ.or AUG M1 .G6.1.0005 1PZR-W4CSE NC MCM 1201.01-0170 001 NDE-68 VT-2 (VT-2) Bare Metal Visual examination of Pressurizer Class Welds.

PZR Safety Nozzle to Safe End Weld 1PZR-W4CSE Ml .G6.1.0006 1 PZR-W2SE NC MCM 1201.01-0170 001 NDE-68 VT-2 (VT-2) Bare Metal Visual examination of Pressurizer Class Welds.

PZR Spray Nozzle to Safe End Weld 1PZR-W2SE Ml .66.2.0001 1PZR-MANWAY NC MCM 1201.01-0170 001 NDE-68 VT-2 CS-Inconel 0.000 / 0.000 Pressurizer Manway Diaphram Seal Weld. Bare Metal Class MCM 1201.01-0186 Visual Exam by VT-2 qualified inspector. Examine the gap between the Pressurizer Manway Cover and Manway for evidence of diaphram plate seal weld leakage. (For responsible individual, contact J.M.

Shuping, Alloy 600 Enginerring Nuclear Technical Services). Reference NRC Bulletin 2004-01. To be done every Outage (EOC-18 through EOC-31)

PZR Manway Insert (Gap Between Manway Cover and PZR) 1PZR-W 11 B-A B-..g M1 .11.21.0001 B01.021.001 1RPV6-446B NC MCM 1201.01-204 PDI-UT-6 UT CS 7.300 / 0.000 50376 CLOSURE HEAD RING PC. 446-03 TO CLOSURE Circumferential Class 1 MCM 1201.01-225 HEAD CAP PC. 446-04. Examined EOC-18, 70.8%

coverage. Reschedule to EOC-19 to get additional coverage. Reference PIP M-07-02243.

Head Ring to Head Cap M1 .B1.22.0004 B01.022.004 1RPV1-446D NC MCM 1201.01-204 PDI-UT-6 UT CS 7.300 / 0.000 50376 CLOSURE HEAD MERIDIONAL WELD AT Longitudinal Class 1 MCM 1201.01-225 APPROXIMATELY 252 DEGREES. Only one UT Procedure required for this exam.

Head to Head M1 .11.22.0005 801.022.005 1 RPV1-446E NC MCM 1201.01-204 PDI-UT-6 UT CS 7.300 / 0.000 50376 CLOSURE HEAD MERIDIONAL WELD AT Longitudinal Ctass 1 MCM 1201.01-225 APPROXIMATELY 324 DEGREES. Only onie UT Procedure required for this exam.

Head to Head Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 15 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv. ,tage 4 (EOC-18)

Summary Nun. Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / Historical Data Category B-D M1..B3.110.0001 B03.1 10.001 1PZR-10 NC MCM1201.01-170 NDE-820 UT CS 2.550 / 24.500 50337 PRESSURIZER SURGE NOZZLE TO LOWER HEAD.

Circumferential Class 1 MCM 1201.01-171 Nozzle to Head M1 .13.110.0001 B03.1 10.001 1PZR-10 NC MCM 1201.01-170 NDE-640 UT CS 2.550 / 24.500 50337 PRESSURIZER SURGE NOZZLE TO LOWER HEAD.

Circumferential Class 1 MCM 1201.01-171 Nozzle to Head M1 .83.120.0004 B03.120.001 1PZR-10R NC MCM 1201.01-170 NDE-680 UT CS 2.550 / 24.500 CB-01-163 PRESSURIZER SURGE NOZZLE TO LOWER HEAD.

Circumferential Class 1 MCM 1201.01-171 (INSIDE RADIUS SECTION)

Nozzle to Head Category B-G-2 M1 .37.50.0003 B07.050.003 1NC-5-FL3 NC MCFI 1NC-5 NDE-62 VT-1 CS 10.000/ 1.375 FLANGE BOLTING (12 STUDS). BOLT SIZE Class 1 MC-ISIN3-1553-02.00 DETERMINED USING CHART IN M/P/O/A/7650/01 ENCLOSURE 13.2. EXAMINE ALL BOLTING MATERIAL.

Ml .B7.50.0004 B07.050.200 1 NV-25-FL2 NV MCFI 1NV-25 NDE-62 'VT-1 SS 0.000 / 1.000 FLANGE BOLTING (4 STUDS). BOLT SIZE Class 1 MC-ISIN3-1554-01.00 DETERMINED USING CHART IN M/P/0/A/7650/01 ENCLOSURE 13.2. EXAMINE ALL BOLTING MATERIAL.

Category B-N-1 M1.B13.10.0001 B13.010.001 1RPV-INTERIOR NC MCM 1201.01-146 NDE-63 VT-3 SS 0.000 / 0.000 AREA ABOVE AND BELOW CORE MADE Class 1 MCM 1201.01-223 ACCESSIBLE DURING REFUELING OUTAGES.

INSPECT ONCE EACH INSPECTION PERIOD Category B-O M1.814.10.0022 B14.010.010 1RPV-CRDM-64 NC MCM 1201.01-224 NDE-35 PT SS-Inconel 0.642 / 4.000 CRD HOUSING WELD. (PERIPHERAL). SHROUD Class 1 MC-ISIN3-1553-01.00 MUST BE REMOVED BEFORE EXAMINATION CAN BE PERFORMED.

Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuie I Bf6/2007 S:29:23 AM Page 16 of 26

i nis report inGiuaes aii cnanges mnrougn aaaenaum 1MI'i-UZb. i ne user is responsible tor veritying this report against the issued plan.

McGuire 1, 3rd Interv, tage 4 (EOC-18)

Summary Nu... Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Caeg C-C M1 .C3.20.0054 C03.020.053 1-MCA-NV-Hi5 NV MCSRD-NVD/sht. 3 NDE-35 PT SS 0.125 / 6.000 WELDED ATTACHMENT Rigid Support Class 2 MC-ISIN3-1554-03.01 1-MCA-NV-H15 Catgogp D-A M1.D1.10.0008 D01.010.007 1KCHX-SUPPORT-1A KC MCM 1201.06-24 NDE-65 VT-1 NA 1.000 / 0.000 Component Cooling Heat Exchanger 1A Welded Class 3 MC-ISIN3-1573-01.00 Attachment. Scheduled for Outage 4 per PIP M 2995. This satisfies PIP and Third Interval requirements.

M1 .D1.10.0009 D01.010.008 1KCST-SUPPORT-1A KC MCM 1201.04-113 NDE-65 VT-1 NA 0.250 / 0.000 Compnoent Cooling Surge Tank 1A Welded Class 3 MC-ISIN3-1573-01.01 Attachment. Scheduled for Outage 4 per PIP M 2995. This satisfies PIP and Third Interval requirements. Equipment Number 1 KCTKO009 M1 .D1.10.0010 D01.010.009 1KFHX-SUPPORT-1A KF MCM 1201.06-0027 NDE-65 VT-1 NA 0.250 / 0.000 Fuel Pool Cooling Heat Exchanger 1A Welded Class 3 MC- 1220-32 Attachment. Scheduled for Outage 4 per PIP M MC-ISIN3-1573-02.00 2995, This satisfies PIP and Third Interval requirements, Equipment Number 1KFHX0003 M1.D1.10.0017 D01.010.003 1VGTK-SUPPORT-1A1 VG MCM 1301.00-80 NDE-65 VT-1 NA 0.312 / 0.000 Diesel Generator Starting Air Tank 1A1 Welded Class 3 MC-ISIN3-1609-04.00 Attachment. Scheduled for Outage 4 per PIP M 2995. This satisfies PIP and Third Interval requirements, Equipment Number 1VGTKO062 M1.D1.10.0019 D01.010.005 1KDHX-SUPPORT-1A KD MCM 1201,06-0042 NDE-65 VT-1 NA 0.750 / 0.000 Diesel Generator Cooling Water Heat Exchanger 1A Class 3 MC-ISIN3-1609-01.00 Welded Attachment. Additional exam added Outage 4 per PIP M-06-2995. This additional exam does not apply to the third interval percentages. Equipment Number 1KDHX0013 rnnteo ~l~I~uuI ~:~I:~ AM WU~U~ V. U(/U2/U( SDQA Cat "C' McGuire 1 8/6/2007 9:29:23 AM Page 17of26 Printed 8/6/2007 9:31:53 AM GJUB302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 17 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv itage 4 (EOC-18)

Summary Num Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Cae2IX D-A M1.D1.10.0020 D01.010.006 1RNST-SUPPORT-1A RN MCM 1218.02-8 NDE-65 VT-1 NA 0.500 /0.000 Nuclear Service Water Strainer 1A Welded Attachment.

Class 3 MCM 1218.02-9 Additional exam added Outage 4 per PIP M-06-2995.

MC-ISIN3-1574-01.00 This additional exam does not apply to the third interval percentages. Equipment Number 1RNST0001 M1.D1.10.0022 1KDC-SUPPORT-1A LD MCM-1301.00-0050 NDE-65 VT-1 NA 0.000 / 0.000 Diesel Generator Lube Oil Cooler 1A Support.

Class 3 MC-ISIN3-1609.01.00 Scheduled for Outage 4 per PIP M-06-2995. This satisfies PIP and Third Interval requirements.

Equipment Number: 1LDHX0019 M1 .D1.10.0023 1RHRHX-SUPPORT-1A ND MCM 1201.06-0022 NDE-65 VT-1 NA 0.750/0.000 1A RESIDUAL HEAT REMOVAL HEAT EXCHANGER Class 3 MCM 1201.06-48 SUPPORT WELDED ATTACHMENT. EXAMINE SEISMIC LUG AT TOP OF ND HEAT EXCHANGER 1A. EXAMINE WITH M1.Fl.40.0116. REFERENCE PIP M-07-323.

M1.D1.10.0025 1CSHX-SUPPORT-1A NS MCM 1201.06-0025 NDE-65 VT-1 NA 0.750 / 0.000 1A CONTAINMENT SPRAY HEAT EXCHANGER Class 3 MC-1220-103 SUPPORT WELDED ATTACHMENT. EXAMINE SEISMIC TIE DOWN LUGS AT TOP OF NS HEAT EXCHANGER 1A. EXAMINE WITH MI.F1.40.0109.

REFERENCE PIP M-07-323.

catego ELC M1..H1.1.0001 1RPV1-462A-SE NC MCFI-1N138 PDI-UT-10 UT CS/Inconel 0.750/6.500 Component 0 degrees, Pc. 459-01 to Pc. 446-04.

MCM 1201.01-113 50374 Class 1 RPV Head to UHI Tube M1 .H1-.1.0002 1RPV1-462B-SE NC MCFI-1N138 PDI-UT-10 UT CS/Inconel 0.750/6.500 Component 90 degrees, Pc. 459-01 to Pc. 446-04.

MCM 1201.01-113 50374 Class 1 RPV Head to UHI Tube Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 18 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv ,tage 4 (EOC-18)

Summaey Num Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / Historical Data Catego ELC M1 .H1.1.0003 1RPV1-462C-SE NC MCFI-1N138 PDI-UT-10 UT CS/Inconel 0.750/6.500 Component 180 degrees, Pc. 459-01 to Pc. 446-04.

MCM 1201.01 -113 50374 Class 1 RPV Head to UHI Tube M1 .H1.1.0004 1RPV1-462D-SE NC MCFI-1N138 PDI-UT-10 UT CS/Inconel 0.750/6.500 Component 270 degrees, Pc. 459-01 to Pc. 446-04.

MCM 1201.01-113 50374 Class 1 RPV Head to UHI Tube M1.H1.1.0005 1NI1FW-38-1 NC MCFI-1N138 PDI-UT-10 UT Inconel 0.625 / 6.250 50374 UHI End Cap To 459-03 180 Deg.

Class 1 MCM 1201.01-113 MCM 1201.01-492 UHI End Cap To PC. 459-03 M1.H1.1.0006 1NI1FW-38-2 NC MCFI-1N138 PDI-UT-10 UT Inconel 0,625 / 6.250 50374 UHI End Cap To 459-03 90 Deg.

Class MCM 1201.01-113 MCM 1201.01-492 UHI End Cap To PC. 459-03 Ml .H1.1.0007 1NI1FW-38-3 NC MCFI-1N138 PDI-UT-10 UT Inconel 0.625 / 6.250 50374 UHI End Cap To 459-03 0 Deg.

Class MCM 1201.01-113 MCM 1201.01-492 UHI End Cap To PC. 459-03 M1 .H1.1.0008 1NIlFW-38-4 NC MCFI-1NI38 PDI-UT-10 UT Inconel 0.625 / 6.250 50374 UHI End Cap To 459-03 270 Deg.

Class MCM 1201.01-113 MCM 1201.01-492 UHI End Cap To PC. 459-03 Cateaorv F-A M1.F1.10.0017 F01.010.017C 1-MCR-NC-579 NC MCSRD-WL-02/sht. 5 NDE-66 VT-3 NA 0.000 / 2.000 Mech Snubber Class 1 Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 19 of 26

This report Includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Intery itage 4 (EOC-18)

Summary Nun, Insp Component ID/ Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData categor *F-A M1.Fi.10.0039 F01.010.1080 1-MCR-NI-548 NI MCSRD-NI-03/sht. 2 NDE-66 VT-3 NA 0.000 /10.000 Hyd Snubber Class 1 Ml .Fl.10.0040 F01.010.1O9A 1-MCR-NI-565 NI MCSRD-NI-03/sht. 4 NDE-66 VT-3 NA 0.000/ 6.000 Rigid Support Class 1 Ml .Fl.10.0041 F01.010.11OA, FO1.010.11OB 1-MCR-NI-567 NI MCSRD-NI-03/sht. 5 NDE-66 VT-3 NA 0.000 / 10.000 Rigid Support Class 1 M1 F1.10.0062 F01.010.159A 1-MCR-NV-1061 NV MCSRD-NV-04/sht. 1 NDE-66 VT-3 NA 0.000 / 2.000 Rigid Support Class 1 Ml .Fl.10.0063 F01.010.160C 1-MCR-NV-1063 NV MCSRD-NV-04/sht. 1 NDE-66 VT-3 NA 0.000 / 2.000 Spring Hgr Class 1 M1..F1.10.0207 F01.010.165A, F01.010.6439 1-MCR-NV-1231 NV MCSýRD-NV-02/sht. 3 NDE-66 VT-3 NA 0.000 /3.000 Rigid Support Class 1 M1.7F1.20.0073 F01.020.208C 1-MCR-NI-541 NI MCSRD-NI-03/sht. 3 NDE-66 VT-3 NA 0.000 /6.000 Hyd Snubber Class 2 MC-ISIN3-1562-03.01 Ml .Fl.20.0082 F01.020.217A 1-MCR-NI-700 NI MCSRD-NI-11/sht.2 NDE-66 VT-3 NA 0.000 / 2.000 Rigid Support Class 2 MC-ISIN3-1562-03.01 M1 .F1.20.0083 F01.020.218A 1-MCR-NI-701 NI MCSRD-Nl-11/sht.2 NDE-66 VT-3 NA 0.000 / 2.000 Rigid Support Class 2 MC-ISIN3-1562-03.01 M1 1.20.0088 F01.020.223C 1-MCR-NI-719 NI MCSRD-NI-11/sht.3 NDE-66 VT-3 NA 0.000 / 2.000 Hyd Snubber Class 2 MC-ISIN3-1562-03.01 MI.Fl.20.0385 F01.020.653A, F01.020.653B 1-MCR-VQ-505 VQ MCSRD-VQ-02/sht. 1 NDE-66 VT-3 NA 0.000 /6.000 Rigid Support Class 2 MC-ISIN3-1585-01.00 Printed 8/6/2007 9:31:53 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page20 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv., itage 4 (EOC-18)

Summary Num Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Cateao F-A M1 .F1.20.0509 F01,020.2796, F01.020.6784 1-MCA-NS-H43 NS MCSRD-NSA/sht. 2 NDE-66 VT-3 NA 0.000 / 10.000 Rigid Restraint Class 2 MC-ISIN3-1563-01.00 Ml .Fl.20.0779 F01.020.237A, F01.020.7311 1-MCR'NI-502 NI MCSRD-NI-01/sht. 2 NDE-66 VT-3 NA 0.000 / 8.000 Rigid Support Class 2 MC-ISIN3-1562-03.01 Ml .Fl.20.0796 F01.020.238A, F01.020.7342 1-MCR-NI-550 NI MCSRD-NI-03/sht. 3 NDE-66 VT-3 NA 0.000 / 6.000 Rigid Support Class 2 MC-ISIN3-1562-03.01 M1 .F1.20.0858 F01.020.239A, F01.020.7465 1-MCR-NI-767 NI MCSRD-NI-09/sht. 3 NDE-66 VT-3 NA 0.000 / 4.000 Rigid Support Class 2 MC4.SIN3-1562-03.00 M1.F1.20.0916 F01.020.282B, F01.020.7578 1-MCR-NS-551 NS MCSRD-NS-02/sht. 2 NDE-66 VTo3 NA 0.000 / 8.000 Rigid Restraint Class 2 MC-ISIN3-1563-01.00 M1 F1.20.0917 F01.020.2836, F01.020.7579 1-MCR-NS-552 NS MCSRD-NS-02/sht. 2 NDE-66 VT-3 NA 0.000 / 8.000 Rigid Restraint Class 2 MC-ISIN3-1563-01.00 Ml.Fl.20.0948 F01.020.2848, F01.020.7640 F

1-MCR-NS-651 NS MCSRD-NS-04/sht. 2 NDE-66 VT-3 NA 0.000 / 8.000 Rigid Restraint Class 2 MC-ISIN3-1563-01.00 M1.F1.20.0949 F01.020.285B, F01.020.7641 1-MCR-NS-652 NS MCSRD-NS-04/sht. 2 NDE-66 VT-3 NA 0.000 / 8.000 Rigid Restraint Class 2 MC-ISIN3-1563-01.00 M1.F17.20.0950 F01.020.286B, F01.020.7642 1-MCR-NS-653 NS MCSRD-NS-04/sht. 2 NDE-66 VT-3 NA 0.000 / 8.000 Rigid Restraint Class 2 MC-ISIN3-1563-01.00 M1.Fl.20.1174 F01.020.052C 1 -MCA-CF-H153 CF MCSRD-CFC/sht. 1 NDE-66 VT-3 NA 0.000 / 18.000 Spring Hgr Class 2 MC-ISIN3-1591-01.01 Ml.Fl.20.1187 F01.020.168C 1 -MCA-ND-H251 ND MCSRD-FWA/sht. 4 NDE-66 VT.3 NA 0.000/12.000 Mech Snubber Class2 MC-ISIN3-1561-01.00 9:31:54 AM 6JU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 21 of 26 Printed 8/6/2007 Printed 816/20079:31:54AMGJU8302 v.07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 21 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv. tage 4 (EOC-18)

Summary Num Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData category F-A M1.F1.20.1188 F01.020.169C 1-MCA-ND-H255 ND MCSRD-FWA/sht. 4 NDE-66 VT-3 NA 0.000 / 12.000 Hyd Snubber Class 2 MC-ISIN3-1561-01.00 M1.F17.20.1189 F01.020.170C 1-MCA-ND-H256 ND MCSRD-FWA/sht. 4 NDE-66 VT-3 NA 0.000 / 12.000 Hyd Snubber Class 2 MC-ISIN3-1561-01.00 M1 .F1.20.1220 F01.020.003A 1-MCR-CA-H390 CA MCSRD-CAM/sht. 1 NDE-66 VT-3 NA 0.000 / 6.000 Rigid Support Class 2 MC-ISIN3-1592-01.00 M1 .Fl.20.1247 F01.020.325A 1-MCA-NV-H37 NV MC-1190-NV-01-02 NDE-66 VT-3 NA 0.000 / 4.000 Rigid Support Class 2 MC-ISIN3-1554-02.01 M1.F1.20.1248 F01.020.326B MC-1683-NV.04-R36 NV MC-1683-NV.04 NDE-66 VT-3 NA 0.000 / 2.000 Rigid Restraint Class 2 MC-ISIN3-1554-03.01 M1.F1.20.1249 F01.020.327B 1-MCA-NV-H39 NV MC-1190-NV-01-01 NDE-66 VT-3 NA 0.000 / 4.000 Rigid Restraint Class 2 MC-ISIN3-1554-03.01 M1.F1.20.1250 F01.020.328A 1-MCA-NV-H40 NV MC-1 190-NV-01-01 NDE-66 VT-3 NA 0.000 / 4.000 Rigid Support Class 2 MC-ISIN3-1554-03.01 M1 .F1.20.1251 F01.020.265C 1-MCA-NS-H85 NS MCSRD-NSB/sht. 1 NDE-66 VT-3 NA 0.000 / 10.000 Hyd Snubber Class 2 MC-ISIN3-1563-01.00 M1. F1.20.1255 F01.020.329A 1-MCA-NV-H41 NV MC-1190-NV-01-03 NDE-66 VT-3 NA 0.000 / 3.000 Rigid Support Class 2 MC-ISIN3-1554-03.01 M1 .F1.30.0072 F01.030.1:30 1-MCA-KC-1043 KC MCSRD-KC-313/sht.2 NDE-66 VT-3 NA 0.000 / 8.000 Rigid Restraint Class 3 MC-ISIN3-1573-02.02 M1 .Fl.30.0073 FO1.030.131B 1-MCA-KC-1030 KC MCSRD-KC-313/sht.3 NDE-66 VT-3 NA 0.000 / 8.000 Rigid Restraint Class 3 MC-ISIN3-1573-02.02 Printed 8/6/2007 9:31:54 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 22 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv 'tage 4 (EOC-18)

Summary Num Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Category F-A M1 .Fl.30.1105 F01.030.002B 1-MCA-CA-H285 CA MCSRD-CAA/sht.1 NDE-66 VT-3 NA 0.000 / 8.000 Rigid Restraint Class 3 MC-ISIN3-1592-01.01 M1 .F1.30.1106 F01.030.003A 1-MCA-CA-H358 CA MCSRD-CAA/sht.1 NDE-66 VT-3 NA 0.000 / 6.000 Rigid Support Class 3 MC-ISIN3-1592-01.01 Ml .Fl.40.0031 F01.040.006B, F01.040.007 1RCP-B-SUPPORT NC MC-1070-08.01 NDE-66 VT-3 NA 0.000 / 0.000 REACTOR COOLANT PUMP 1B SUPPORT.

Class 1 MC-ISIN3-1553-01.00 EXAMINE SUPPORT COLUMNS AND LATERAL MC-1070-17, MC-1070-2, RESTRAINT. EOC-18 / OUTAGE 4 REINSPECTION MC-1070-7 OF SUPPORT TO INCLUDE LATERAL RESTRAINT.

REFERENCE PIP M-07-323.

Ml .Fl.40.0059 F01.040.0148 1CSP-SUPPORT-1A NS MCM 1201.05-206 NDE-66 VT-3 NA 0.000 /0.000 CONTAINMENT SPRAY PUMP 1A SUPPORT.

Class 2 MC-ISIN3-1563-01.00, EXAMINE HORIZONTAL RESTRAINT AND VERTICAL M@:1 @99:66-00, MC- SUPPORT. REFERENCE PIP M-07-323.

1690-14 M1 .F1.40.0062 F01.040.026B 1KDHX-SUPPORT-1A RN MCM 1201.06-0042 NDE-66 VT-3 NA 0.750 / 0.000 DIESEL GENERATOR COOLING WATER HEAT Class 3 MC-ISIN3-1574-02.00 EXCHANGER 1A SUPPORT.

Ml .F1.40.0063 F01.040.027B 1KDC-SUPPORT-1A LD MCM-1301.00-0050 NDE-66 VT-3 NA 0.000 / 0.000 Diesel Generator Lube Oil Cooler 1A Support.

Class 3 MC-ISIN3-1609.01.00 Scheduled for Outage 4 per PIP M-06-2995. This satisfies PIP and Third Interval requirements.

M1 .Fl.40.0067 F01.040.0228 1KCST-SUPPORT-1A KC MCM 1201.04-113 NDE-66 VT-3 NA 0.250 / 0.000 COMPONENT COOLING SURGE TANK 1A SUPPORT.

Class 3 MC-ISIN3-1573-01.01 M .FlP.40.0069 F01.040.024B 1KCHX-SUPPORT-1A KC MCM 1201.06-24 NDE-66 VT-3 NA 1.000/0.000 COMPONENT COOLING HEAT EXCHANGER 1A Class 3 MC-ISIN3-1573-01.00 SUPPORT.

M1 .F1.40.0087 F01.040.029B 1VGTK-SUPPORT-1A1 VG MCM 1301.00-80 NDE-66 VT-3 NA 0.312 / 0.000 DIESEL GENERATOR STARTING AIR TANK 1A1 Class 3 MC-ISIN3-1609-04.00 SUPPORT SKIRT.

Printed 8/6/2007 9:31:54 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 23 of 26

This report Includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv itage 4 (EOC-18)

Summary Num- Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData CateQory F-A M11F1.40.0091 F01.040.033B 1RNST-SUPPORT-11A RN MCM 1218.02-8 NDE-66 VT-3 NA 0.500 / 0.000 NUCLEAR SERVICE WATER STRAINER 1A Class 3 MC-ISIN3-1574-01.01 SUPPORT MCM 1218.02-9 Mi .F1.40.0109 F01.040.008 1CSHX-SUPPORT-1A NS MCM 1201.06-0025 NDE-66 VT-3 NA 0.000 / 0.000 1A CONTAINMENT SPRAY HEAT EXCHANGER Class 2 MC-1220-103 SUPPORT. EXAMINE LOWER SUPPORT AND UPPER LATERAL RESTRAINTS. EXAMINE WITH.

Mi.D1.10.0025. EOC-18/OUTAGE 4 REINSPECTION OF SUPPORT TO INCLUDE UPPER LATERAL RESTRAINTS. REFERENCE PIP M-07-323.

M1.F1.40.0113 F01.040.012B 1RHRP-SUPPORT-IA ND MCM 1201.05-0048 NDE-66 VT-3 NA 0.000 /0.000 RESIDUAL HEAT REMOVAL PUMP 1A SUPPORT.

Class 2 MC-ISIN3-1561-01.00 EXAMINE HORIZONTAL RESTRAINT AND VERTICAL MCm1680.00-00, MC- SUPPORT. REFERENCE PIP M-07-323 1690-16 M1 .F1.40.0114 F01.040.013B 1SIP-SUPPORT-1A NI MCM-1201.05-0454 NDE-66 VT-3 NA 0.000/ 0.000 SAFETY INJECTION PUMP 1A SUPPORT.

Class 2 MC-ISIN3-1562-03.00 Mi.F1.40.0115 F01.040.004B 1SGA-COLUMNS NC MC-1070-4 NDE-66 VT-3 NA 0.000 / 0.000 STEAM GENERATOR 1A SUPPORT COLUMNS (4 Class 1 Mc-ISIN3-1553-01.00 ASSEMBLIES). REFERENCE DRAWING MCM MC-1070-17 1201.01-0782.

M1 .F1.40.0116 F01.040.007 1RHRHX-SUPPORT-1A ND MCM 1201.06-0022 NDE-66 VT-3 NA 0.000 / 0.000 1A RESIDUAL HEAT REMOVAL HEAT EXCHANGER Class 2 MCM 1201.06-48 SUPPORT. EXAMINE LOWER SUPPORT AND UPPER RESTRAINTS. EXAMINE WITH M1.D1.10.0023. EOC-18 / OUTAGE 4 REINSPECTION OF SUPPORT TO INCLUDE UPPER RESTRAINTS. SUPPORT EXAMINED EOC-15/

OUTAGE 1. REFERENCE PIP M-07-323.

M1.F1.40.0117 F01.040.021B 1KFHX-SUPPORT-1A KC MCM 1201.06-0027 NDE-66 VT-3 NA 0.250 / 0.000 FUEL POOL COOLING HEAT EXCHANGER 1A Class 3 MC-ISIN3-1570-01.01 SUPPORT.

MC- 1220-32 Printed 8/6/2007 9:31:54 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page24 of 26

This report includes all changes through addendum 1MNS-026. The user is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Intervi !age 4 (EOC-18)

Summary Num Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched Thick/Dia Cal Blocks Comments / HistoricalData Catecorv F-A Mi .F1.40.0129 IFWST-SUPPORT FW MCM 1201.04-0129 NDE-66 VT-3 Refueling Water Storage Tank support. Equipment ID#

- Class 2 1FWTK-0001. Scheduled for Outage 4 per PIP M 2995. This satisfies PIP and Third Interval requirements. The Refueling Water Storage Tank is considered a storage tank therefore inspection of welded attachment per VT-1 is not required per Mark Pyne letter dated August 2006.

M1.F1.40.0130 1CRDM-SUPPORT NC MCM 1201.13-23 NDE-66 VT-3 NA 0.000 /0.000 REACTOR VESSEL CRDM SEISMIC SUPPORT.

Class 1 MCM 1201.13-24 EXAMINE TURN BUCKLES, ALTHOUGH NOT MCM 1201.13-25 REQUIRED BY CODE (PER MARK PYNE AND KEVIN RHYNE) THE FRAME WILL BE VISUALLY EXAMINED AS A SUPPLEMENT TO THE TURN BUCKLE EXAM.

Cateory . R-A M1.R1.11.0037 Risk Segment NC-005 R01.011.005 1SGA-OUTLET-W6SE NC MC1676-4 PDI-UT-10 UT SS-CS 2.500 /31.000 5149697 STEAM GENERATOR 1A OUTLET NOZZLE.

MCM 1201.01-0782 5158172 DRAWING # MC-ISIN3-1553-01.00. SEGMENT NC-Circumferential Class 1 005. NDE-12/RT MAY BE SUBSTITUTED IN LIEU OF PDI-UT-MCM 1201.01-0769 10/UT.

Dissimilar Terminal End Nozzle To Safe End M1.R1.11.0101 Risk Segment NS-017 R01.011.101 1NS148-4 NS MCFI-1NS47 NDE-12 RT SS 0.148 / 8.000 SEGMENT NS-017.

Circumferential Class 2 MC-ISlN3-1563-01.00 ELBOW TO PIPE Mi.R1.11.0142 Risk Segment NI-063B R01.011.085 1N1231-1 NI MCFI-1NI74 NDE-995 UT SS 0.281 / 1.500 50202 SEGMENT NI-063B.

Circumferential Class 2 MC-ISlN3-1562-01.00 Full Coupling to Pipe M1.R1.11.0143 Risk Segment NI-063B R01.011.086 1N1270B-13 NI MCFI-1NI75 NDE-995 UT SS 0.281 / 1.500 50202 SEGMENT NI-063B.

Circumferential Class 2 MC-ISIN3-1562-01.00 Pipe to Reducer Printed 8/6/2007 9:31:54 AM GJU8302 v, 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 25 of 26

This report includes all changes through addendum 1 MNS-026. The upr is responsible for verifying this report against the issued plan.

McGuire 1, 3rd Interv, tage 4 (EOC-18)

Summary Num Insp Component ID / Type System ISO/DWG Numbers Procedure Req Mat Sched ThickWDia Cal Blocks Comments / HistoricalData categoov._ R-A M1.R1.11.0250 Risk Segment NS-018 R01.011.102 1NS123-4 NS MCFI-1NS48 NDE-12 AT SS 0.148 / 8.000 SEGMENT NS-018.

Circumferential Class 2 MC-ISIN3-1563-01.00 ELBOW TO PIPE M1.R1.11.2104 Risk Segment NV-002B R01.011.136 1NV1FWI182-13 NV MCFI-1NV182 PDI-UT-2 UT SS 0.237 /4.000 PDI-UT-2-M SEGMENT NV-002B.

Circumferential Class 2 MC-ISIN3-1554-03.00 *SEE SECTION 8 FOR CALIBRATION BLOCK REQUIREMENTS. Only one UT Procedure required for this exam.

Tee to Pipe M1.R1.11.2109 Risk Segment NV-019AA R01.011.141 1NV1F12A-12 NV MCFI-1NV10 PDI-UT-2 UT SS 0.438 /3.000 PDI-UT-2-M SEGMENT NV-019AA.

Circumferential Class 2 MC-ISIN3-1554-03.00 *SEE SECTION 8 FOR CALIBRATION BLOCK REQUIREMENTS. Only one UT Procedure required for this exam.

TEE TO PIPE M1.R1.11.2124 Risk Segment NV-109 R01.011.168 1RCPA-TE NV MCFI-1NV11 PDI-UT-2 UT SS 0.438 /3.000 PDI-UT-2-M RECIPROCATING CHARGING PUMP Circumferential Class 2 MC-ISIN3-1554-03.00 ACCUMULATOR. SEGMENT NV-109.

MCM 1201.01-0197 *SEE SECTION 8 FOR CALIBRATION BLOCK REQUIREMENTS.

Only one UT Procedure required for this exam.

Terminal End Tee to Flange M1 .R1.11.2125 Risk Segment NV-11OA R01.011.169 1NV1 F479 NV MCFI-1NV11 PDI-UT-2 UT 0.438 / 3.000 PDI-UT-2-M SEGMENT NV-1 10A.

Circumferential Class 2 MC-ISIN3-1554-03.00 *SEE SECTION 8 FOR CALIBRATION BLOCK REQUIREMENTS.

Only one UT Procedure required for this exam.

ELBOW TO PIPE Printed 8/6/2007 9:31:54 AM GJU8302 v. 07/02/07 SDQA Cat "C" McGuire 1 8/6/2007 9:29:23 AM Page 26 of 26

4.0 Results of Insnections Performed The results of each examination shown in the final Inservice Inspection Plan (Section 3 of this report) are included in this section. The completion date and status for each examination are shown. All examinations revealing reportable indications and any corrective action required as a result are described in further detail in Subsections 4.1 and 4.2. Corrective measures performed and limited examinations are described in further detail in Subsections 4.3 and 4.4.

The information shown below is a field description for the reporting format included in this section of the report:

ITEM NUMBER = ASME Section XI Tables IWB-2500-1 (Class 1), IWC-2500-1 (Class 2), IWF-2500-1 (Class 1 and Class 2),

Augmented, and Risk Informed Requirements ID NUMBER = Unique Identification Number SYSTEM = Component System Identification INSP DATE = Date of Examination INSP STATUS = CLR Clear REC Recordable REP Reportable INSP LIMITED = Indicates inspection was limited Coverage obtained is listed GEO REF = Y Yes (Geometric Reflector N No applies only to UT)

Y Yes RFR (Relief Request) = NNo COMMENTS General and/or Detail Description Outage 4/EOC 18 Refueling Outage Report Page 1 of 2 McGuire Unit 1 Revision 0 Section 4 August 9, 2007

4.1 Reportable Indications EOC 18 (Outage 4) had no reportable indications during this report period, 4.2 CorrectiveAction Corrective action is action taken to resolve flaws and relevant conditions, including supplemental examinations, analytical evaluations, repair/ replacement activities, and corrective measures. There were no recordable conditions that required corrective action during this report period.

4.3 Corrective Measures Corrective measures are actions (such as maintenance) taken to resolve relevant conditions, but not including supplemental examinations, analytical evaluations, and repair / replacement activities. Any corrective measures performed for examinations associated with this report period will be shown on the examination data sheets which are on file at the Duke's Corporate Office in Charlotte, North Carolina.

4.4 Limited Examinations Limitations (i.e., 90% or less of the required examination coverage obtained) identified for examinations associated with this report period are shown below.

A relief request will be submitted to seek NRC acceptance of the limited coverage.

This information will be on file at the Duke's Corporate Office in Charlotte, North Carolina.

Summary Number Descriptionof Limitation

• M1 .B1.21.0001 Coverage Limitation (70.80%)

M1 .B3.1 10.0001 Coverage Limitation (81.30%)

M1.R1.1 1.0142 Coverage Limitation (24.75%)

M1.R1.1 1.0143 Coverage Limitation (34.65%)

M1 .R1.11.2124 Coverage Limitation (35.40%)

• Final status pending completion of PIP#M-07-2243 Problem Evaluation/Corrective Action.

Outage 4/EOC 18 Refueling Outage Report Page 2 of 2 McGuire Unit 1 Revision 0 Section 4 August 9, 2007

DUKE ENERGY CORPORA TION QUALITY ASSURANCE ý, "HNICAL SERVICES Inservice Inspection DatabaseManagement System Inspection Results McGuire 1, 3rd Interval, Outage 4 (EOC-.18)

Report for EOC-18 results.

Insp Insp Insp Geo Summary No Component ID System Date Status Limited Ref RFR Comment M1 .B1.21.0001 1 RPV6-446B NC 03/30/07 CLR 70.80% N Y UT-07-022 Final status pending completion of PIP# M-07-2243 Problem Evaluation/Corrective Action..

Ml .B1.22.0004 1RPV1-446D NC 03/30/07 CLR N N N UT-07-020 M1.1B1.22.0005 1RPV1-446E NC 03/30/07 CLR N N N UT-07-021 M1.113.10.0001 1RPV-INTERIOR NC 04/18/07 CLR N N N VT-07-032 M1.B14.10.0022 1RPV-CRDM-64 NC 03/31/07 CLR N N N PT-07-002 M1.B3.110.0001 1PZR-10 NC 03/15/07 CLR 81.30% N Y UT-07-006 RFR will be submitted. Reference PIP# M-07-04405.

NC 03/15/07 CLR 81.30% N Y UT-07-007 RFR will be submitted. Reference PIP# M-07-04405.

M1.B3.120.0004 1PZR-10R NC 03/15/07 CLR N N N UT-07-005 M1.B7.50.0003 1NC-5-FL3 NC 04/10/07 CLR N N N VT-07-031 M1 .87.50.0004 1NV-25-FL2 NV 04/02/07 CLR N N N VT-07-016 Printed 8/13/2007 2:56:01 PM GJU8302 SDOQA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page 1 of 9

Report for EOC-ýQ- results.

Insp Insp Insp Geo Summary No Component ID System Date Status Limited Ref RFR Comment Ml .C3.20.0054 1-MCA-NV-H15 NV 03/08/07 CLR N N N PT-07-001 M1 .D1.10.0008 1KCHX-SUPPORT-1A KC 10/25/06 CLR N N N VT-07-076 M1 .D1.10.0009 1KCST-SUPPORT-1A KC 10/26/06 CLR N N N VT-07-077 M1 .D1.10.0010 1KFHX-SUPPORT-1A KF 10/26/06 CLR N N N VT-07-078 M1.D1.10.0017 1VGTK-SUPPORT-1A1 VG 10/26/06 CLR N N N VT-07-079 M1.Dl.10.0019 1KDHX-SUPPORT-1A KD 10/26/06 CLR N N N VT-07-080 M1 .D1.10.0020 1RNST-SUPPORT-1A RN 11/14/06 CLR N N N VT-07-075 Ml .D1.10.0022 1KDC-SUPPORT-1A LD 11/14/06 CLR N N N VT-07-081 M1 .D1.10.0023 1RHRHX-SUPPORT-1A ND 04/04/07 CLR N N N VT-07-033 M1 .D1.10.0025 1CSHX-SUPPORT-1A NS 03/23/07 CLR N N N VT-07-034 M1.Fl.10.0017 1-MCR-NC-579 NC 03/12/07 CLR N N N VT-07-035 M1.F1.10.0039 1-MCR-NI-548 NI 03/14/07 CLR N N N VT-07-036 Ml .Fl.10.0040 1-MCR-NI-565 NI 03/14/07 CLR N N N VT-07-037 Printed 8/13/2007 2:56:01 PM GJU8302 SDQA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page2 of 9

Report for EOC-.1-9 results.

Insp /nsp Insp Geo.

Summary No Component ID

• System Date Status Limited Ref RFR Comment M1.F1.10.0041 1-MCR-NI-567 NI 03/16/07 CLR N N N VT-07-038 Ml .Fl.10.0062 1-MCR-NV-1061 NV 03/15/07 CLR N N N VT-07-039 M1.F1.10.0063 1-MCR-NV-1063 NV 03/15/07 REC N N N VT-07-073 Acceptable for continued service as this is not considered a discrepancy.

Aluminum travel stops are not allowed in the Reactor Building.

M1.F1.10.0207 1-MCR-NV-1231 NV 03/15/07 REC N N N VT-07-074 Acceptable for continued service. Reference WR#922908.

Ml .Fl.20.0073 1-MCR-NI-541 NI 03/14/07 CLR N N N VT-07-017 M11F1.20.0082 1-MCR-NI-700 NI 03/14/07 CLR N N N VT-07-018 Ml .Fl.20.0083 1-MCR-NI-701 NI 03/14/07 CLR N N N VT-07-019 M15F1.20.0088 1-MCR-NI-719 NI 03/14/07 CLR N N N VT-07-020 Ml .Fl.20.0385 1-MCR-VQ-505 VQ 03/17/07 CLR N N N VT-07-021 NT M15 1F.20.0509 1-MCA-NS-H43 NS 01/22/07 CLR N N N VT-07-041 Ml .F1.20.0779 1-MCR-NI-502 NI 03/14/07 CLR N N N VT-07-022 Ml .F1.20.0796 1-MCR-NI-550 NI 03/14/07 CLR N N N VT-07-023 Printed 8/13/2007 2:56:01 PIVI GJU8302 SDQA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page 3 of 9

Report for EOC-t.,results.

Insp Insp Insp Geo Summary No Component ID System Date Status Limited Ref RFR Comment Ml .Fl.20.0858 1-MCR-NI-767 NI 03/14/07 CLR N N N VT-07-024 Ml .Fl.20.0916 1-MCR-NS-551 NS 03/15/07 CLR N N N VT-07-025 Ml.Fl.20.0917 1-MCR-NS-552 NS 03/15/07 CLR N N N VT-07-026 Ml .F1.20.0948 1-MCR-NS-651 NS 03/15/07 CLR N N N VT-07-027 M1 Fl.20.0949 1 -MCR-NS-652 NS 03/15/07 CLR N N N VT-07-028 Ml .Fl.20.0950 1-MCR-NS-653 NS 03/15/07 CLR N N N VT-07-029 Ml.Fl.20.1174 1-MCA-CF-H153 CF 01/24/07 CLR N N N VT-07-042 M1 .F1.20.1187 1-MCA-ND-H251 ND 01/15/07 CLR N N N VT-07-043 Ml .Fl.20.1188 1-MCA-ND-H255 ND 01/15/07 CLR N N N VT-07-044 Ml.Fl.20.1189 1-MCA-ND-H256 ND 01/15/07 CLR N N N VT-07-045 M15F1.20.1220 1-MCR-CA-H390 CA 03/17/07 CLR N N N VT-07-030 Ml .Fl.20.1247 1 -MCA-NV-H37 NV 01/15/07 CLR N N N VT-07-046 Ml.Fl.20.1248 MC-1683-NV.04-R36 NV 01/15/07 CLR N N N VT-07-047 Printed 8/13/2007 2:56:01 PM GJU8302 SDQA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page 4 of 9

Report for EOC,'-Q results.

I Insp Insp Insp Geo Summary No Component ID System Date Status Li nited Ref RFR Comment M1.F1.20.1249 1-MCA-NV-H39 NV 01/15/07 CLR N N N VT-07-048 Ml .Fl.20.1250 1-MCA-NV-H40 NV 01/15/07 REC N N N VT-07-072 Acceptable for continued service. Reference WR#917313.

M1 .Fl.20.1251 1-MCA-NS-H85 NS 01/15/07 CLR N N N VT-07-049 MI.F1.20.1255 1-MCA-NV-H41 NV 01/15/07 CLR N N N VT-07-050 Ml .Fl.30.0072 1-MCA-KC-1043 KC 01/15/07 CLR N N N VT-07-051 Ml .Fl.30.0073 1-MCA-KC-1030 KC 01/15/07 CLR N N N VT-07-052 Ml .Fl.30.1105 1-MCA-CA-H285 CA 01/22/07 CLR N N N VT-07-053 M1 .Fl.30.1106 1-MCA-CA-H358 CA 01/22/07 CLR N N N VT-07-054 Ml .Fl.40.0031 1RCP-B-SUPPORT NC 03/27/07 CLR N N N VT-07-057 MlF1.40.0059 1CSP-SUPPORT-1A NS 03/26/07 CLR N N N VT-07-058 M1.F1.40.0062 1KDHX-SUPPORT-1A RN 10/26/06 CLR N N N VT-07-082 M15F1.40.0063 1KDC-SUPPORT-1A LD 11/14/06 CLR N N N VT-07-083 MlF51.40.0067 1KCST-SUPPORT-1A KC 11/13/06 CLR N N N VT-07-084 Orinted 8/13/2007 2:56:01 PM GJU8302 SDOA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page5 of 9

Report for EOC--*. results.

Insp Insp Insp Geo.

Summary No Component ID System Date Status Limited Ref RFR Comment Ml .Fl.40.0069 1KCHX-SUPPORT-1A KC 10/25/06 CLR N N N VT-07-087 M1 .Fl.40.0087 1VGTK-SUPPORT-1A1 VG 10/26/06 CLR N N N VT-07-085 M1 F1.40.0091 1RNST-SUPPORT-lA RN 11/14/06 CLR N N N VT-07-071 Ml .Fl.40.0109 1CSHX-SUPPORT-lA NS 03/23/07 CLR N N N VT-07-059 Ml .Fl.40.0113 1RHRP-SUPPORT-1A ND 01/23/07 CLR N N N VT-07-055 Ml .Fl.40.0114 1SIP-SUPPORT-1A NI 01/23/07 CLR N N N VT-07-056 Ml .Fl.40.0115 1SGA-COLUMNS NC 03/26/07 CLR N N N VT-07-060 Ml .Fl.40.0116 1 RHRHX-SUPPORT-1A ND 04/04/07 CLR N N N VT-07-061 M1.F1.40.0117 1KFHX-SUPPORT-IA KC 10/26/06 CLR N N N VT-07-086 M1.F1.40.0129 1FWST-SUPPORT FW 11/09/06 REC N N N VT-07-089 Acceptable for continued service. Reference WR#1714760.

Ml .Fl.40.0130 1CRDM-SUPPORT NC 04/27/07 CLR N N N VT-07-088 Ml .G5.1.0001 RPV-HEAD-PEN NC 03/26/07 CLR N N N UT-n/a NC 03/31/07 CLR N N N VT-2-n/a Printed 8/13/2007 2:56:02 PM GJU8302 SDQA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page 6 of 9

Report for EOC-o-. results.

Insp Insp Insp Gec&

Summary No Component ID System Date Status Limited Ref RFR Comment M1.G5.2.0001 1RPV-VENT-NOZZLE NC 03/20/07 CLR N N N PT-n/a NC 03/28/07 CLR N N N UT-n/a NC 03/31/07 CLR N N N VT-2-n/a NC 03/31/07 CLR N N N VT-2-n/a Ml .G5.3.0001 1RPV3-445E-SE NC 04/23/07 CLR N N N VT-07-062 Ml .G5.3.0002 1RPV3-445F-SE NC 04/23/07 CLR N N N VT-07-063 Ml .G5.3.0003 1 RPV3-445G-SE NC 04/23/07 CLR N N N VT-07-064 Ml .G5.3.0004 1RPV3-445H-SE NC 04/23/07 CLR N N N VT-07-065 M1.G5.3.0005 1RPV3-445A-SE NC 04/23/07 CLR N N N VT-07-066 Ml .G5.3.0006 1RPV3-445B-SE NC 04/23/07 CLR N N N VT-07-067 Ml .G5.3.0007 1RPV3-445C-SE NC 04/23/07 CLR N N N VT-07-068 Ml .G5.3.0008 1RPV3-445D-SE NC 04/23/07 CLR N N N VT-07-069 M1.G6.1.0001 1PZR-WISE NC 03/13/07 CLR N N N VT-07-009 Ml .G6.1.0002 1PZR-W3SE NC 03/12/07 CLR N N N VT-07-01 0 Printed 8/13/2007 2:56:02 PM GJU8 302 SDQA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page 7 of 9

Report for EOC-.- results.

Insp Insp Insp Geo.

Summary No Component 10 System Date Status Limited Ref RFR Comment Ml .G6.1.0003 1PZR-W4ASE NC 03/12/07 CLR N N N VT-07-011 M1.G6.1.0004 1PZR-W4BSE NC 03/12/07 CLR N N N VT-07-012 M1 .G6.1.0005 1 PZR-W4CSE NC 03/12/07 CLR N N N VT-07-013 M1.G6.1.0006 1PZR-W2SE NC 03/12/07 CLR N N N VT-07-014 M1 .G6.2.0001 1 PZR-MANWAY NC 03/12/07 CLR N N N VT-07-015 M1.H1.1.0001 1RPV1-462A-SE NC 03/31/07 CLR 96.50% N N UT-07-017 M1..H1.1.0002 1RPV1 -4628-SE NC 03/31/07 CLR 96.50% N N UT-07-016 M1. H1.1.0003 1RPV1-462C-SE NC 03/31/07 CLR 96.50% N N UT-07-012 M1.1-11.1.0004 1RPVl-462D-SE NC 03/31/07 CLR 96.50% N N UT-07-013 M1.H1.1.0005 1NI1FW-38-1 NC 03/31/07 CLR 13.50% N N UT-07-014 M1.H1.1.0006 1NI1FW-38-2 NC 03/31/07 CLR 48.40% N N UT-07-018 M1.H1.1.0007 1NIlFW-38-3 NC 03/31/07 CLR 32.70% N N UT-07-019 M1.H1.1.0008 1NIlFW-38-4 NC 03/31/07 CLR 32.90% N N UT-07-015 Printed 8/13/2007 2:56:02 PM GJU8302 SDQA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page 8 of 9

Report for EOC-1-- results.

Insp Insp Insp Geo-Summary No Component ID System Date Status Limited Ref RFR Comment Ml .R1.11.0037 1SGA-OUTLET-W6SE NC 03/25/07 CLR 98.75% N N UT-07-009 M1.Ri.11.0101 1NS148-4 NS 04/08/07 CLR N N N RT-n/a M1.R1.11.0142 1N1231-1 NI 03/27/07 CLR 24.75% N Y UT-07-01 0 RFR will be submitted. Reference PIP# M-07-04405.

M1.Rl.11.0143 1N1270B-13 NI 03/27/07 CLR 34.65% N Y UT-07-011 RFR will be submitted. Reference PIP# M-07-04405.

M1 .R1.11.0250 1NS 123-4 NS 04/08/07 CLR N N N RT-n/a M1.R1.1 1.2104 1NV1FW182-13 NV 03/05/07 CLR 94 .90% N N UT-07-008 M1.R1.1 1.2109 1NV1F12A-12 NV 03/08/07 CLR 93 .40% N N UT-07-003 M1.R1.1 1.2124 1RCPA-TE NV 03/05/07 CLR 35 .40% N Y UT-07-001 RFR will be submitted. Reference PIP# M-07-01351.

M1.R1.11.2125 1NV1F479 NV 03/08/07 CLR N N N UT-07-004 Printed 8/13/2007 2:56:02 PM GJU8302 SDQA Cat "C" v. 07/02/07 McGuire 1 8/13/2007 2:55:15 PM Page9 of 9

5.0 Owner's Report for Repair / Replacement Activities As required by the applicable code, records of Class 1 and Class 2 Repair and Replacement work is included on NIS-2 forms in this section.

No items were determined to have work performed outside this report period.

Work Order Number Signoff Date/EOC PIP Number NONE NONE NONE The NIS-2 forms included in this section were completed for work performed during this report period.

The individual work request documents and manufacturers' data reports are on file at McGuire Nuclear Station.

5.1 Class 1 and 2 Preservice Examinations As required by the applicable code, Preservice Inspection (PSI) Examinations were performed on ISI Class 1 and 2 items during this report period. All Class 1 and 2 PSI examination data listed below is on file in the McGuire Nuclear Station QA Vault.

Work Order Number Identification Number ISl Type of Class Inspection 566530 KC System flange B VT-1 575412 1 MCA- FW-123 B VT-3 575432 1 MCA-SM-141 B VT-3 575434 1 MCA-SM-184 B VT-3 576004 1 NVFE5530 B VT-1 578182 1 MCA-ND-227 B VT-3 578647 Valve 1NV6 B VT-3 578647 1 MCR-NV-1 178 B VT-3 582082 1 MCR-KC-822 B VT-3 586237 Valve 1NV-483 B VT-3 588116 1 MCR-NC-783 A VT-3 588116 NC System Weld Over A UT Lay 588670 Valve 1NC-1/NC Piping A VT-3 588674 1 MCR-ND-281 B VT-3 588932 1 MCA-NC-59 B VT-3 588932-15 1 MCR-BB-711 B VT-3 Outage 4/EOC 18 Refueling Outage Report Page 1 of 3 McGuire Unit 1 Revision 0 Section 5 August 9, 2007

Work Order Number Identification Number ISI Type of Class Inspection 588932-17 1 MCA-SV-1 1 B VT-3 589045 1 NC-SG-B B VT-3 589664-01 Valve 1NV-238 B VT-3 589944 Valve 1ND-56 B VT-1 589945 Weld 1NC1F1014 B UT 591201 1 MCR-NC-807 A VT-3 591203 1 MCR-NI-528 A VT-3 591204-01 1 MCR-NI-552 A VT-3 591205-01 1 MCR-NI-658 A VT-3 591206 1 MCR-NI-661 A VT-3 591207 1 MCR-NV-1 070 B VT-3 591238-01 1 MCR-CA-H443 B VT-3 591337 1 MCR-NV-855 A VT-3 591342-01 1 MCR-NI-541 B VT-3 591344 1 MCR-NI-676 B VT-3 591345-01 1 MCR-NI-721 B VT-3 591346 1 MCR-NI-880 A VT-3 591347-01 1 MCR-NI-895 B VT-3 591348-01 1 MCR-NI-905 B VT-3 591349 1 MCR-NI-911 A VT-3 591350-01 1 MCR-NI-953 B VT-3 591354 1 MCA-FW-122 B VT-3 591359 1 MCR-BB-568 B VT-3 591360-01 1 MCR-NC-809 A VT-3 591361 1 MCR-NI-510 B VT-3 591362 1 MCR-NI-699 B VT-3 591363 1 MCR-NI-702 B VT-3 591364-01 1 MCR-NI-719 B VT-3 591365 1 MCR-NI-744 B VT-3 591393-01 1 MCR-NC-801 A VT-3 591394 1 MCR-NC-811 A VT-3 591395 1 MCR-NC-813 A VT-3 591396-01 1 MCR-NC-900 A VT-3 591397-01 1 MCR-NC-902 B VT-3 591398 1.MCR-NC-903 A VT-3 591399 1 MCR-NI-548(A) A VT-3 591401 1 MCR-NI-548(B) A VT-3 591402 1 MCR-NI-549(A) A VT-3 591403 1 MCR-NI-549(B) A VT-3 591404 1 MCR-NI-569(A) A VT-3 591405 1 MCR-NI-569(B) A VT-3 591406 1 MCR-NI-717 B VT-3 Outage 4/EOC 18 Refueling Outage Report Page 2 of 3 McGuire Unit 1 Revision 0 Section 5 August 9, 2007

Work Order Number Identification Number ISI Type of Class Inspection 591407 1 MCR-NI-850 A VT-3 591408 1 MCR-NI-852 B VT-3 591409 1 MCR-NI-879 B VT-3 591415 1 MCR-S-NF-100-01-O B VT-3 591417 1 MCR-S-VX-100-01-HH B VT-3 591418 1 MCR-S-VX-100-01-JJ B VT-3 591439-01 1 MCR-BB-537 B VT-3 591440 1 MCR-BB-561 B VT-3 591442 1 MCR-BB-567 B VT-3 591443 1 MCR-BB-645 B VT-3 591444 1 MCR-CA-445 B VT-3 591531-01 1 MCR-NI-515 A VT-3 591575 NS System Bolting B VT-1 591576 NS System Bolting B VT-1 591597 1 MCR-CF-405 B VT-3 591910 NS System Piping B UT 591910 1 MCR-NS-751 B VT-3 595413 1 MCR-FW-125 B VT-3 1699266 Valve 1 NS-39 B VT-1 1714956 Valve 1NI-184 B VT-1 1716964 1 MCR-NS-23 B VT-3 1716964/54 Valve 1NS-165/Piping B VT-1 1716964/55 Valve 1NS-166/Piping B VT-1 1730551 Valve 1NC-VA-2 A VT-1 1730552 Valve 1NC-VA-3 A VT-1 1732837 Valve 1NV-482/Piping B VT-1 1732869 Valve 1NV-486/Piping B VT-1 1732931 Valve 1NV-487/Piping B VT-1 1737115 1 MCR-ND-508 A VT-3 1739915 Valve 1NS-1 B VT-1 1741867 1 MCR-KC-749 B VT-3 1741917 1 MCR-NV-1025 B VT-3 1742718 Valve 1VI-124 B VT-1 1744670 Valve 1NI-159 A VT-1 1744836 1 MCR-BB-665 B VT-3 1746129 1 MCR-BB-501 B VT-3 1746264 1 MCR-NV-1235 A VT-3 1746595 1 MCR-CA-389 B VT-3 1746782 Valve 1NS-25/Piping B VT-1 1749672 Valve 1-IAE-CV-5370 B VT-1 98672034/06 Valve 1 NM-92 B VT-1 Outage 4/EOC 18 Refueling Outage Report Page 3 of 3 McGuire Unit 1 Revision 0 Section 5 August 9, 2007

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date May 24, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: MoGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: Gi1 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 566530 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: KC - Component Cooling 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped

% Installed (yes or no)

A 0 Repaired, 0 No KC System Duke Power N/A 38 N/A 1981 0 Replaced,

]0 Replacement 01 Yes B 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

\_ _ 0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0EYes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work machined face of flange at upper oil cooler of 1C Reactor Coolant Pumo Motor.

8. Tests Conducted:Hydrostatic E Pneumatic El Nom. Operating Press. 0 Other LI ExemptOl Pressure 100 psig Test Temp. 70.2 OF Pressure psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed C: , a FL Grass JrQA Tech Specialist Date

, Owner or wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CThave. ins.ecte, the components described in this Owner's Report during the period

• //' *Tto .; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injuryor property damage or a loss of any kind arising from or connected with this inspection.

R" /-L/-r . --.-

• F Swan Commissions NC1524, N-I Inspector's ;Si**t7ujre National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 10, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hapers Ferry Road, Huntersville, NC 28078 2a. Unit: E1l 02 03 --Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 575412 Address: 526 S. Church Street,. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: FW - Refueling Water 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 12 No 1-MCA-FW-123 Duke Power 19155 N/A N/A N/A 12 Replaced, El Replacement El Yes B El Repaired, 21 No 1-MCA-FW-123 Duke Power 27676 N/A N/A N/A El Replaced,

[0 Replacement 0l Yes C El Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, El No El Replaced, 0_ Replacement El Yes E El Repaired, El No El Replaced,

_ EReplacement El Yes F El Repaired, El No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work -Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt[Z Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section X1.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed"l *

• FL Grass J r.QA Tech Specialist Date ,, -_2 ___

Ownerei?'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT ave inspqcted the components described in this Owner's Report during the period I,/L-,/7 7 tot 01; and state that to the best of my knowledge and belief, the Owner hai performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injur or property damage or a loss of any kind arising from or connected with this "inspection.m___

y -7

. -- aerome F Swan Commissions NC1524, N-I SInspector's gatie National Board, State, Province and Endorsements K "/ Date '

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 9. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address:. McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: 21 02 03 EJShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 575432 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/_AA Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: SM - Main Steam 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME I111971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0 No 1-MCA-SM-141 Duke Power 00001 N/A N/A N/A 10 Replaced,

__ Replacement El Yes B El Repaired, 0 No 1-MCA-SM-141 Duke Power 16551 N/A N/A N/A El Replaced,

[0 Replacement El Yes C El Repaired, El No El Replaced,

_E Replacement El Yes D El Repaired, El No El Replaced,

_E Replacement El Yes E El Repaired, El No El Replaced,

_E Replacement El Yes F 0l Repaired, El No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work -Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt-Z Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed. FL Grass JrQA Tech Specialist

" Owner,46 Owner's Date Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina- and employed by HSB CT have ins e te the components described in this Owner's Report during the period 3L21t '27to - j2/40 47; and state that to the best of my knowledge and belief, the Owner h-As pefrformed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ny personal inju or property damage or a loss of any kind arising from or connected with this nspection.,

spectin- . _o F Swan Commissions NC1524, N-I nspere National Board, State, Province and Endorsements ci Date Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 10, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 575434 Address: 526 S.'Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: SM - Main Steam 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0 No 1-MCA-SM-184 Duke Power 15416 N/A N/A N/A 0 Replaced,

_0 Replacement 0 Yes B 0 Repaired, 01 No 1-MCA-SM-184 Duke Power 15830 N/A N/A N/A 0 Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page I of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptIO Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/._A Certificate of Authorization No. N/A Expiration Date N/A Signed -I- FL Grass Jr,QA Tech Specialist Date Z-Z/1/1f _-I O wner o(Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have inspe tedthe components described in this Owner's Report during the period LI,0/4t7 "3 to 2/zo7; and state that to the best of my knowledge and belief, the Owner h ds performed ex~minrations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju/ly or property damage or a loss of any kind arising from or connected with this 11 inspection.

Jerome F Swan Commissions NC1524, N-I Inspector's"* ature National Board, State, Province and Endorsements i

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 24, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: E1 02 03 OShared (specify Units

3. Work Performed By: Duke Power ComDany 3a. Work Order #: 576004 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NV - Chemical and Volume Control 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, [I No NV System Duke Power N/A 37 N/A 1981 0 Replaced, 1" Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0] Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement C Yes D 0 Repaired, D No 0 Replaced,

]0 Replacement E- Yes E 0 Repaired, C No 0 Replaced,

]0 Replacement C Yes F 0 Repaired, C] No O Replaced,

__ Replacement C Yes Page 1 of 2

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced bolting material at 1NVFE5530.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptI]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks the replacement of bolting material has been exempted from pressure testing per ASME Code Section X1 (interpretation XI-1 08).

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed F,',F 'V FL Grass JrQA Tech Specialist Date 0,,*

Ownbr or ner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H ave ns ted hpcomponents described in this Owner's Report during the period 41/?4/6.7to _M5 . t)/; and state that to the best of my knowledge and belief, the Owner ha's performed exfiminations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ny personal injury or roperty damage or a loss of any kind arising from or connected with this me F Swan Commissions NC1524, N-I r Inspetor'sSignNational Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date April 13, 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: E1 02 03 -Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 578182 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: ND - Residual Heat Removal 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 2 No 1-MCA-ND-277 Duke Power 20703 N/A N/A N/A IZ Replaced, 0 Replacement 0 Yes B 0 Repaired, R1 No 1-MCA-ND-277 Duke Power 21803 N/A N/A N/A 0 Replaced,

_ _Replacement 01 Yes C El Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

_ EReplacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic EJ Pneumatic LI Nom. Operating Press. LI Other LI Exemptr Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE Icertify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/_A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date ,-- '  ?.-

Owner-or-('wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by Tave insp cted the components described in this Owner's Report during the period to and state that to the best of my knowledge and belief, the Owner hs performed e.arnfinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju7 or property damage or a loss of any kind arising from or connected with this inspection.*/

erome F Swan Commissions NC1524, N-I Inspector's S iature National Board, State, Province and Endorsements HDate.,

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR I REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date May 8, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 101 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 578647 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD100045

4. (a) Identification of System: NV - Chemical and Volume Control 4. (b) Class of System: B

5. (a) Applicable Constructictn Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0 No 1 NV6 Dresser TD36317 204 N/A 1976 01 Replaced, O Replacement 10 Yes B 0 Repaired, 0 No 1 NV6 Dresser TP58046 1987 N/A 2006 0 Replaced, RI Replacement 0I Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced Valve 1NV6 per MD100045.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. 21 Other [] ExemptE Pressure 2235 .psig Test Temp. 558 OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks test performed per procedure MP/O/A/7650/076 under w/o# 589246.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date -*-",/, 27 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS.SCT bave nspe ted the components described in this Owner's Report during the period 0to W110 7 and state that to the best of my knowledge and belief, the Owner h ats performed examinlations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for

.any personal injury or property damage or a loss of any kind arising from or connected with this spection.

.- ,.-,,-Jerome F Swan Commissions NC1524, N-I Inspector' *giature National Board, State, Province and Endorsements Date v7_

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date April 19, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: I01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 578647 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp:: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # MD100045

4. (a) Identification of System: NV - Chemical and Volume Control 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for.Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 21 No 1-MCR-NV-1178 Duke Power N/A N/A N/A N/A El Replaced, I [Z Replacement El Yes B El Repaired, El No El Replaced,

_ Replacement El Yes C El Repaired, El No El Replaced,

_ Replacement El Yes D El Repaired, El No El Replaced,

__ Replacement El Yes E El Repaired, El No 0l Replaced, El Replacement El Yes F El Repaired, El No El Replaced,

__ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Modified per MD100045.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptig Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -,,, 1,2 FL Grass Jr,QA Tech Specialist Date 4111"00-7_

/ /1

" Owner of Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CTthave inspeted the components described in this Owner's Report during the period Ai.L 7"to '/ 9,o "V;and state that to the best of my knowledge and belief, the Owner has performed ex*minations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

..'- --'4-*-----Jerome F Swan Commissions NC1524, N-I Inspector's i atu National Board, State, Province and Endorsements C Date Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 22, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 582082 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/LA Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: KC - Component Cooling 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 21 No 1-MCR-KC-822 Duke Power N/A N/A N/A N/A 0 Replaced,

[] Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[] Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced bolting material

8. Tests Conducted:Hydrostatic 0 Pneumatic U Nom. Operating Press. U Other 0 ExemptlZ Pressure .psig Test Temp. OF Pressure psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/__A Certificate of Authorization No. N/A Expiration Date N/A Sinned \-10/2 FL Grass Jr.QA Tech SDecialist Date -41ý 2_WZ v" -wvYner ,*wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H CTave inspe ted Ve components described in this Owner's Report during the period k to ep and state that to the best of my knowledge and belief, the Owner has performed ex'minations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury *_ nproperty damage or a loss of any kind arising from or connected with this Sinspection.- "-

ome F Swan Commissions NC1524, N-I Is-Inspector's S,'Jý e National Board, State, Province and Endorsements 6 Dtea",_..

D/

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date 04/04/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: I[11 02 03 []Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00586237 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/.AA Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NV Chemical and Volume Control 4.(b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 0 No 1NV-483 Dresser TE09054 265 Valve 1978 0 Replaced,

__Replacement [9Yes B 0 Repaired, 0 No 0 Replaced, I0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced Valve Disc

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt[]

Pressure _psig Test Temp. OF Pressure psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed_ -. U,&40F.R. SorrowQA Tech Support Date 04/04, 2007

'Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB C have inspected the components described in this Owner's Report during the period

.313 oQ2 to !?*LVLQ7; and state that to the best of my knowledge and belief, the Owner has performed examinati6ns and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Jerome F Swan Commissions NC1524, N-I inspector' Sig tur.e

-National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 2. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 588116 Address: 526 S. Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD100733

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for.Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0 No 1-MCR-NC-783 Duke Power N/A N/A N/A N/A El Replaced, I 0] Replacement El Yes B El Repaired, El No El Replaced, El Replacement El Yes C El Repaired, El No El Replaced,

_E Replacement El Yes D El Repaired, El No El Replaced,

_E Replacement El Yes E El Repaired, El No El Replaced,

_E Replacement El Yes F El Repaired, El No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Wor k - Pi n~

t:ý I-rAnr i. Fin L:ýL:ý Hnm..

t::

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt[Z Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -* FL Grass JrQA Tech Specialist Date 'IV,*

7

Owner or'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by hted insCT have the components described in this Owner's Report during the period

!1111#7 to w  ; and state that to the best of my knowledge and belief, the Owner has performed exAmihations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for A ny personal injury, property damage or a loss of any kind arising from or connected with this ispection.

• Q erome F Swan Commissions NC1524, N-I Is o Sigatre National Board, State, Province and Endorsements I1 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date May 8. 2007 526 S Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 O.Shared (specify Units .)

3. Work Performed By: Duke Power Company 3a. Work Order #: 588116 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # MD1 00733

4. (a) Identification of System: NC- Reactor Coolant 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N-504-2, N-638-1, & 2142-2 Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A RI Repaired, 0 No NC System Duke Power N/A 28 N/A 1981 0 Replaced, 10 Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Performed weld over-lay per MD100733. See remarks below for the weld numbers.

8. Tests Conducted:Hydrostatic [] Pneumatic LI Nom. Operating Press. I] Other LI Exempto Pressure 2235 psig Test Temp. 558 OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks 1-PZR-W4ASE (NW-2), 1-PZR-W4BSE (NW-4), 1-PZR-W4CSE (NW-3), 2-PZR-W3SE (NW-1), 1-PZR-W2SE (NW-5), and 1PZR-W1SE (NW-6).

test performed per procedure MP/O/A/7650/076 under w/o# 589246.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section X1.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass JrQA Tech Specialist Date Owner orowner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT, have inspectel the components described in this Owner's Report during the period 7 .7 to 't0/7/ o'/* and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury o property damage or a loss of any kind arising from or connected with this inspection.--h"f-

/---,,,A-derome F Swan Commissions NC1524, N-I Inspector'* SI#g~re National Board, State, Province and Endorsements

• !Date _.*/ J/0, Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code.Section XI

1. Owner Address: Duke 1Power Company la. Date May 3. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet I of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 21 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 588670 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, [I No 1-NC-1 Crosby N56925-00-0004 28 N/A 1974 21 Replaced, 1 0 Replacement 0 Yes B 0 Repaired, 0 No 1-NC-1 Crosby N56925-00-0004 28 N/A 1974 0 Replaced, 0 Replacement 0 Yes C 0 Repaired, 0 No NC Piping Duke Power N/A 28 N/A 1981 0 Replaced, R1 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 10 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced valve after being refurbished at the test facility and replaced bolting material in the inlet flange during installation.

8. Tests Conducted:Hydrostatic Ii Pneumatic E Nom. Operating Press. 10 Other El ExemptO Pressure 2235 psig Test Temp. 558 OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks test performed per MP/O/A/7650/076 under w/o# 589246.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed \j FL Grass JrQA Tech Specialist Date_

O*kner q'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by ve inspetethe components described in this Owner's Report during the period aCT

• . 7to S"8y-'o7;

.. and state that to the best of my knowledge and belief, the Owner his performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju7 or property damage or a loss of any kind arising from or connected with this inspection.

,p- I--.*z,,rome F Swan Commissions NC1524, N-I Inspector' 'Si ature National Board, State, Province and Endorsements Ise* Y Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 6. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 588674 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #l Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: ND - Residual Heat Removal 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 01 No 1-MCR-ND-281 Duke Power N/A N/A N/A N/A 0 Replaced, I 0 11 Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced load pin and nuts.

8. Tests Conducted:Hydrostatic [] Pneumatic 0] Nom. Operating Press. El Other El Exempt[o Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed - FL Grass Jr.QA Tech Specialist Date

" her or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by

_HS Chave tel the components described in this Owner's Report during the period

, 7"Ll/7 to /0/0' 7; and state that to the best of my knowledge and belief, the Owner has p rformed examinrati*ns and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable.in any manner for fany insection.--*

personal in ]y; or property damage or a loss of any kind arising from or connected with this rome F Swan Commissions NC1524, N-I Inspector' S~Lnat re National Board, State, Province and Endorsements Date _. 7 ..

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 22, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: 01 0-2 03 E"Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # r, a 013 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/_AA Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, RI No 1-MCA-NC-59 Duke Power 3817 N/A N/A N/A R0 Replaced,

[0 Replacement 0 Yes B 0 Repaired, 12 No 1-MCA-NC-59 Duke Power 614770/022 N/A N/A N/A 0 Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 10 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl--

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed 1 FL Grass Jr,QA Tech Specialist Date 0"//,v _

Owner orOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by SB CT have inspe ted the components described in this Owner's Report during the period to /-L..0  ; and state that to the best of my knowledge and belief, the Owner Iihs peformed e3Amin ations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injuryr property damage or a loss of any kind arising from or connected with this inspection l*n r .-

a t- r , *rxeme F Swan Commissions NC1524, N-I "Inspector's.(ature/ National Board, State, Province and Endorsements I

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date April 16, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: [01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 588932-15 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: BB - Steam Generator Blowdown Recycle 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0 No 1-MCR-BB-71 1 Duke Power 6430 N/A N/A N/A 0 Replaced,

]0 Replacement El Yes B 0l Repaired, 0 No 1-MCR-BB-711 Duke Power 01615123/075 N/A N/A N/A 0 Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0 No El Replaced, 0 Replacement El Yes D 0 Repaired, 0 No 0 Replaced, El Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

_E Replacement 0 Yes FE Repaired, El No El Replaced,

__ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. El Other El Exempt[l Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed::-~'Y%,w4' FL Grass JrQA Tech S~ecialist Date __

- Owner oOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspected the components described in this Owner's Report during the period

-'- 2 *v7 to !-,(6-- Z7; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for

/ any personal injuy or property damage or a loss of any kind arising from or connected with this inspection._/o

ý,z,-ý/rome F Swan Commissions NC1524, N-I K

/nspector'seSi2Oaure National Board, State, Province and Endorsements

/Date 2"//;

,oo 7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 15, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 588932-17 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: SV - Main Steam Vent to Atmosphere 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0 No 1-MCA-SV-1 1 Duke Power 4071 N/A N/A N/A Z Replaced,

__ Replacement El Yes B E Repaired, 0 No 1-MCA-SV-11 Duke Power 01615123/072 N/A N/A N/A El Replaced, 13 Replacement El Yes C El Repaired, El No El Replaced, 0E Replacement El Yes D El Repaired, El No 0l Replaced,

__ Replacement El Yes E El Repaired, El No El Replaced, 0E Replacement El Yes F El Repaired, El No El Replaced,

_]E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptO Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed 'V -*V4 FL Grass Jr,QA Tech Specialist Date Owner of Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSI CThave' ins te the components described in this Owner's Report during the period

.+/-jfLOiZto 71&7!Y; and state that to the best of my knowledge and belief, the Owner has performed exAminations and taken corrective measures described in this Owner's Report.in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injuryor property damage or a loss of any kind arising from or connected with this f*inspection. *

-.-- ,-Jerome F Swan Commissions NC1524, N-I SInspector's Ilg re National Board, State, Province and Endorsements

( Date/- 1-__

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 22, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 0l1 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 589045 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME 11 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0 No 1-NC-SG-B Duke Power 3 N/A N/A N/A l] Replaced,

__ Replacement 0l Yes B El Repaired, El No El Replaced, El Replacement El Yes C El Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, 0l No El Replaced,

_ Replacement El Yes E El Repaired, El No El Replaced, 0_ Replacement El Yes F El Repaired, 0l No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced control valves in snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. IZ Other El Exemptl]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that. the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed " , , FL Grass Jr.QA Tech Specialist Date 49 '2

'Owner ot'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CThave inspe ted the components described in this Owner's Report during the period Y/2& l to ./-.7  ; and state that to the best of my knowledge and belief, the Owner has perormed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ny personal inju or property damage or a loss of any kind arising from or connected with this pnspection.

, .Le - Jerome F Swan Commissions NC1524, N-I Inspector's i at National Board, State, Province and Endorsements Date 2--,/0D7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company I a. Date 03/29/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: 9*1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00589664-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/_.A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NV Chemical and Volume Control 4(b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0] Repaired, 0 No 1NV-238 Fisher 5921348 789 Valve 1976 0 Replaced,

_IFReplacement IElYes B 0 Repaired, 0 No 0 Replaced,

[0 Replacement 01 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 10 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced Plug Assembly

8. Tests Conducted:Hydrostatic IZ Pneumatic 5 Nom. Operating Press. 0 Other LI Exemptn]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed7 .,, F.R. SorrowQA Tech Support Date 03/29, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CThave insp cte~i the components described in this Owner's Report during the period

/a4A7 to '9 n/oL ; and state that to the best of my knowledge and belief, the Owner his performed e amirations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury property damage or a loss oI any kind arising from or connected with this me F Swan Commissions NC1524, N-I Inspecto s Sig .eNational Board, State, Province and Endorsements Datev~s V/'

L)_

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date June 5,2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: E01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 589944 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: ND - Residual Heat Removal 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0 No ND System Duke Power N/A 35 N/A 1981 0 Replaced,

.... R1 Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced, El Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, E0 Replacement 0 Yes E 0 Repaired, 0 No 0l Replaced,

_E Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced inlet bolting material (nut) on inlet flange of valve 1ND56.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt--

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks test exempted from pressure testing per ASME Code Section Xl: Interpretation XI-1-89-08.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A 2

Signed .*4.zad. FL Grass JrQA Tech Specialist Date 1 _ev 7 Owner off'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS O ave ins*ete tt components described in this Owner's Report during the period to 0!Z; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this

/inspection'.-F rome F Swan Commissions ý NC1524, N-I Inspectors p4iure National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company 1a. Date May 4. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet of

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: 0l1 02 113 OShared (specify Units

3. Work Performed By: Duke Power Companv 3a. Work Order #: 589945 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: ND - Residual Heat Removal 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 0 No ND System Duke Power N/A 35 N/A 1981 0 Replaced, EI Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced,

[0 Replacement 01 Yes C 0 Repaired, 0 No 0 Replaced, 10 Replacement [0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Cut out and rewelded weld NC1 F1014 and replaced 1 1/2" flange.

8. Tests Conducted:Hydrostatic Ii Pneumatic El Nom. Operating Press. 10 Other El Exempto Pressure 324 psig Test Temp. 91 OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks test performed per MP/O/A/7650/076.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/_A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date oc_2 Owner or-'wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by jjaTh have inspepted the components described in this Owner's Report during the period

-to_-;*f .0 : and state that to the best of my knowledge and belief, the Owner omd examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury r property damage or a loss of any kind arising from or connected with this rome F Swan - Commissions NC1524, N-I Inspector's n, re "DatNational Board, State, Province and Endorsements K

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date April 11, 2007 5262 S' Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 rShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591201 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 2 No 1-MCR-NC-807 Duke Power 14957 N/A N/A N/A 01 Replaced, 1 0 Replacement 0 Yes B 0 Repaired, R0 No 1-MCR-NC-807 Duke Power 20736 N/A N/A N/A 0 Replaced, 121 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

_0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic E Pneumatic El Nom. Operating Press. Li Other El ExemptrZ Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed . .*jA. FL Grass JrQA Tech Specialist Date ___

' Oner op)wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by 1 have insp te ýhe components described in this Owner's Report during the period W1v7 to zl.Z 7; and state that to the best of my knowledge and belief, the Owner has performed e aminations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ny personal injury or roperty damage or a loss of any kind arising from or connected with this

- rome F Swan Commissions NC1524, N-I

/ Inspector'sS i re National Board, State, Province and Endorsements

( SDate '/Y_

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR /FREPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section X1

1. Owner Address: Duke Power Company la. Date March 30, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hacqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591203 Address: 526 S. Church Street., Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME Ill 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section X1 Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0 No 1-MCR-NI-528 Duke Power 15871 N/A N/A N/A E0 Replaced,

[0 Replacement 0 Yes B 0 Repaired, 0] No 1-MCR-N1-528 Duke Power 19765 N/A N/A N/A 0 Replaced, El Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 11 Replaced,

]0 Replacement 0l Yes E 0 Repaired, 0 No 0 Replaced, 1:1 Replacement 0 Yes F 0 Repaired, 0 No 03 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic [J Pneumatic 0 Nom. Operating Press. 0 Other 0 Exemptl-Pressure psig Test Temp. OF Pressure _psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed N , FL Grass JrQA Tech Specialist Date Owner or*0wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspe tedlhe components described in this Owner's Report during the period to M-3-9'167o"and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

AJ-"!.--eJerome F Swan Commissions NC1524, N-I Inspector's Si ature National Board, State, Province and Endorsements Date -3"/

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date 03/22/07 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 9]1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591204-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. NIA Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Injection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped

.. __ Installed (yes or no)

A 13 Repaired, ZlNo 1MCR-NI-0552 Duke Power 20693 N/A N/A N/A l] Replaced,

[0 Replacement 0 Yes B 0l Repaired, [] No 1MCR-NI-0552 Duke Power 19768 N/A N/A N/A 0l Replaced,

.___Replacement El Yes C El Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, 0l No 0l Replaced, 0l Replacement 0l Yes E 0l Repaired, El No El Replaced,

_E Replacement 0l Yes F El Repaired, 0l No El Replaced,

__ Replacement ol Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Snubber PM Chanqeout

8. Tests Conducted:Hydrostatic El Pneumatic 0l Nom. Operating Press. El Other Li Exempt[Z Pressure .psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are.correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed - F.R.Sorrow, QA Tech. SuDDort Date 03/22, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION .

I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT ave insppcted/the components described in this Owner's Report during the period 4V2-610 7 to .3/-:? 47"; and state that to the best of my knowledge and belief, the Owner h.s performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury, or property damage or a loss of any kind arising from or connected with this inspection. ,

z.,,-.-rome F Swan Commissions NC1524, N-I 1nspector ture National Board, State, Province and Endorsements Date/ /

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date 03/22/07 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 0Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591205-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/.A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Iniection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, []No 1MCR-NI-0658 Duke Power 15882 N/A N/A N/A 0 Replaced, 0_ Replacement 0l Yes B 0l Repaired, Z No 1MCR-NI-0658 Duke Power 15125 N/A N/A N/A El Replaced,

[]0Replacement El Yes C 0l Repaired, 0l No El Replaced, El Replacement El Yes D El Repaired, El No El Replaced, El Replacement El Yes E El Repaired, El No El Replaced,

_ Replacement El Yes F El Repaired, El No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Snubber PM Chanqeout

8. Tests Conducted:Hydrostatic 0l Pneumatic El Nom. Operating Press. El Other El Exemptl9l Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the: report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed,,Wxd41Lo F.R.Sorrow, QA Tech. SuDport Date 03/22, 2007 Owner or Owners Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CThave insp teq,the components described in this Owner's Report during the period 12 Z, '7 to0 3/,/Q and state that to the best of my knowledge and belief, the Owner has pirformed e~amirnations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ny personal injury property damage or a loss of any kind arising from or connected with this Ispection ome F Swan Commissions NC1524, N-I SInspector's Sji a .re National Board, State, Province and Endorsements L .3 _Date _.

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Comoany la. Date 03/29/2007 526 S. Church Street, Charlotte, NC 28201-1006.: Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 191 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591206 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Injection 4(b) Class of System: A

5. (a) Applicable Construction Code: ASME Ill 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, E]No 1MCR-NI-0661 Duke Power 15677 N/A N/A N/A [iReplaced,

[0 Replacement El Yes B El Repaired, lENo 1MCR-NI-0661 Duke Power 20388 N/A N/A N/A El Replaced,

_IFReplacement El Yes C El Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, El No El Replaced, 0_ Replacement 0l Yes E 0l Repaired, El No O Replaced,

__ Replacement El Yes F 0l Repaired, El No 0l Replaced, 0_ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work PM Snubber Chanaeout

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt(9 Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section X1.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed, d F.R. Sorrow,QA Tech Support Date 03/29, 2007

.Owner or Owners Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS_.CT have inspepted the components described in this Owner's Report during the period 2/&Q30/7 to; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this inspection.

oz&&,- - ,-x.----Jerome F Swan Commissions NC1524, N-I Inspectors Siq ~ture National Board, State, Province and Endorsements

( /Date 3./olý*),

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 10. 2007 526 S. Church Street, Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: E1l 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591207 Address: 526 S. Church Street, Chadotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: NV - Chemical and Volume Control 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, R0 No 1 -MCR-NV-1 070 Duke Power 18935 N/A N/A N/A 01 Replaced,

[0 Replacement 0 Yes B 0 Repaired, 0 No 1-MCR-NV-1070 Duke Power 36601 N/A N/A N/A 0 Replaced,

.... [] Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0l No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. Li Other El Exempti]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass JrQA Tech Specialist Date Y 'Orwner or'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HhB CT have ins the components described in this Owner's Report during the period

/.t - /, to -/7" ; and state that to the best of my knowledge and belief, the Owner as Iperformed 6ýamihations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither theInspector nor his employer shall be liable in any manner for any personal injury r property damage or a loss of any kind arising from or connected with this inspection.

Inspector's .icr f uye erome F Swan Commissions NC1524, N-I National Board, State, Province and Endorsements 11 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date 03/22/07 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 9]1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 00591238-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: CA Auxiliary Feedwater 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, tgNo 1MCR-CA-H443 Duke Power 19291 N/A N/A N/A fg1Replaced, 0 Replacement 0 Yes B 0 Repaired, (ENo 1 MCR-CA-H443 Duke Power 16563 N/A N/A N/A 0 Replaced,

[EReplacement 0 Yes C 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Snubber PM Chanae Out

8. Tests Conducted:Hydrostatic E Pneumatic fl Nom. Operating Press. [ Other El Exempt[9 Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed-z*. F.R. Sorrow, QA Tech. Support Date 03/22 , 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by Hhave inspqcted the components described in this Owner's Report during the period Yto 3/7Z07 and state that to the best of my knowledge and belief, the Owner tfas perormed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employershall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this nspection.

erome F Swan Commissions NC1524, N-I 6 r, nspector Date ý ,

, a re 1-,f// , .

National Board, State, Province and Endorsem ents Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owne&Address: Duke Power Company la. Date April 4, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #:

Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No, N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NV - Chemical and Volume Control 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

C _olumn I Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A .. 0 Repaired, RI No 1-MCR-NV-855 Duke Power 21532 N/A N/A N/A El Replaced, El Replacement El Yes B ]0 Repaired, 0] No 1-MCR-NV-855 Duke Power 21530 N/A N/A N/A 0 Replaced, El Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 01 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, F

... E 0 Replacement 0 Yes El Repaired, El No 0 Replaced,

[0 Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. 0I Other El ExemptI]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -Y '* FL Grass JrQA Tech Specialist Date 7

_i_/_i/*o Owner orOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I,the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSBCThave in ctid the components described in this Owner's Report during the period o/eh 0to Q and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju ror property damage or a loss of any kind arising from or connected with this inspection' *"

Otzv-ý,,-z.P *'* edrome F Swan Commissions NC11524, N-I Inspector's 8'i~tu~e National Board, State, Province and Endorsements

( Date Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date 03/22/07 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville. NC 28078 2a. Unit: 9]1 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591342-01 Address: 526 S. Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, IENo 1MCR-NI-0541 Duke Power 14917 N/A N/A N/A [] Replaced, 0_ Replacement El Yes B El Repaired, Z] No 1MCR-NI-0541 Duke Power 14904 N/A N/A N/A El Replaced,

[IReplacement El Yes C El Repaired, El No El Replaced, 0_ Replacement El Yes D El Repaired, 0l No 0l Replaced, E

0E Replacement El Yes E Repaired, El No El Replaced,

__ Replacement 0l Yes F 0 Repaired, El No El Replaced, 0E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work ~niihhnr PM flh~inn~c~iit Snubber PM Channeout

8. Tests Conducted:Hydrostatic El Pneumatic Li Nom. Operating Press. 0i Other 0i Exempt[O Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed c4di1-L F.R.Sorrow, QA Tech. Support Date 03/22, 2007 Owner or Owners Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H$B C*have insp ctec the components described in this Owner's Report during the period

'21P07 to 3/'2-7/0; and state that to the best of my knowledge and belief, the Owner Kas performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's finspection.

Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any.personal injury or property damage or a loss of any kind arising from or connected with this

.. ome F Swan Commissions NC1524, N-I

-Inspector' sSign /e National Board, State, Province and Endorsements 6 Date Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date March 30, 2007 526 S. Church Street. Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: 0l1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Comoany 3a. Work Order #: 591344 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 12 No 1-MCR-NI-676 Duke Power 14860 N/A N/A N/A 0l Replaced, 10 Replacement 0 Yes B 0 Repaired, E0 No 1-MCR-NI-676 Duke Power 22048 N/A N/A N/A 0 Replaced, E0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement [I Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page I of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl-Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed\ý/ FL Grass Jr.QA Tech Specialist Date _"9D1,.7_ _

,Owner or.'wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT ave inspted the components described in this Owner's Report during the period

.to tt.3/ i7; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ny personal injury or property damage or a loss of any kind arising from or connected with this spection.

-*-Jerome F Swan Commissions NC1524, N-I Inspector's U-2atu National Board, State, Province and Endorsements 6 IDate ... //,46Qi7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date 03/22/07 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: r91 02 03 OShared (specify Units

3. Work Performed By: Duke Power Comoany 3a. Work Order #: 00591345-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0- Repaired, lINo 1MCR-NI-0721 Duke Power 16135 N/A N/A N/A 91 Replaced,

]0 Replacement 0 Yes B 0 Repaired, 9 No 1MCR-NI-0721 Duke Power 00130 N/A N/A N/A 0 Replaced,

__Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page I of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Snubber PM Chanaeout

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. - Other El ExemptlZ Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed - )4ý F.R.Sorrow, QA Tech. Support Date 03/22, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS._.__Chave insp ctedthe components described in this Owner's Report during the period

,,*/, .]0Q7 to 213 q; and state that to the best of my knowledge and belief, the Owner h s performed ex~min'ations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore neither the Inspector nor his employer shall be liable in any manner for

) any personal injury property damage or a loss of any kind arising from or connected with this inspection.

"Inspect~ ini~ AN-a--trome F Swan Commissions NC1524, N-I National Board, State, Province and Endorseme-nts "Date - '--* .

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date March 30, 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 0Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591346 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, 19 No 1-MCR-NI-880 Duke Power 14823 N/A N/A N/A 0 Replaced, 0_ Replacement El Yes B El Repaired, 0 No 1-MCR-NI-880 Duke Power 21695 N/A N/A N/A El Replaced, E0 Replacement 0l Yes C 0l Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, El No 0l Replaced,

• ___ Replacement El Yes E E Repaired, El No El Replaced,

__ Replacement E0 Yes F E Repaired, El No El Replaced,

__ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each -sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptIo Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass JrQA Tech Specialist Date ___

Owner of Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have insp cte the components described in this Owner's Report during the period to: 9; and state that to the best of my knowledge and belief, the Owner as perormed examifiations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injur2ý or property damage or a loss of any kind arising from or connected with this inspection.

Y._)?& fome F Swan Commissions NC1524, N-I Inspector'i ture National Board, State, Province and Endorsements SDate.**_ O Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date 03/22/07 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: lIF1 02 03 -Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591347-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, [gNo 1MCR-NI-0895 Duke Power 20962 N/A N/A N/A 19 Replaced,

[0 Replacement 0 Yes B 0 Repaired, [] No 1MCR-NI-0895 Duke Power 14962 N/A N/A N/A 0 Replaced,

__Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Snubber PM Chanqeout

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptZ]

Pressure _psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made. in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed- F.R.Sorrow, QA Tech. Support Date 03/22, 2007 Owner or Owners Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H5Chave inspgcted the components described in this Owner's Report during the period

,,2/9- 7to3 *, '7; and state that to the best of my knowledge and belief, the Owner hesperforned examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

rome F Swan Commissions NC1524, N-I Inspector's &iature National Board, State, Province and Endorsements Date _ ___

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company 1a. Date 03/27/2007 526 S. Church Street, Charlotte, NC 28201-10066 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: Ell 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591348-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Iniection 4(b) Class of System: , .

5. (a) Applicable Construction Code: ASME II1. 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, IFlNo 1 MCR-NI-0905 Duke Power 20989 N/A N/A N/A [OReplaced,

[0 Replacement 0 Yes B 0 Repaired, 9]No 1MCR-NI-0905 Duke Power 19549 N/A N/A N/A 0 Replaced,

[_Replacement 0 Yes C 0 Repaired, 0 No O Replaced,

_0 [ Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[O Replacement 0 Yes E 0 Repaired, 0 No O Replaced,

[] Replacement 0 Yes F 0l Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work PM Snubber Chanqeout

8. Tests Conducted:Hydrostatic EJ Pneumatic EJ Nom. Operating Press. E Other El Exempt[]

Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed, -"1._*4i&,,t-. F.R. SorrowQA Tech Support Date 03/27, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by have ins ected tle components described in this Owner's Report during the period 2V7 to , and state that to the best of my knowledge and belief, the Owner has performed ex.min~tions and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this inspection.0 eromeF-Swan* Commissions NC1524, N-I Inspector's atur National Board, State, Province and Endorsements Date > y/ , _

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 10, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591349 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Ingection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME I111971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section X1 Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, 0 No 1 -MCR-N I-911 Duke Power 19976 N/A N/A N/A 01 Replaced,

[O Replacement El Yes B El Repaired, 0I No 1-MCR-NI-911 Duke Power 14771 N/A N/A N/A El Replaced,:

0I Replacement El Yes C El Repaired, El No El Replaced,

_ _Replacement El Yes D El Repaired, El No El Replaced, El Replacement El Yes E 0l Repaired, El No El Replaced, El Replacement El Yes FE Repaired, El No El Replaced, Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptElI Pressure _psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section X1.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed- JFL Grass JrQA Tech Specialist Date

/"ývnerorwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS3 CT!have inspucte t e components described in this Owner's Report during the period 9*/ to 1/L/,/ and state that to the best of my knowledge and belief, the Owner h~s peformed edaminations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section X1.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this spection.

• - ,.F Swan Commissions NC1524, N-I Inspectors..Sigr*, re National Board, State, Province and Endorsements Date.

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date 03/22/07 526 S. Church Street. Charlotte: NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: I111 02 03 OShared (specify Units

3. Work Performed By: Duke Power Comoany 3a. Work Order # : 00591350-01 Address: 526 S. Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, [ENo 1MCR-NI-0953 Duke Power 14770 N/A N/A N/A 19 Replaced,

]0 Replacement 0 Yes B 0 Repaired, Z] No 1MCR-NI-0953 Duke Power 14780 N/A N/A N/A 0 Replaced,

__Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced, I 10 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 0] Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, I] Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Snubber PM Chanqeout

8. Tests Conducted:Hydrostatic Li Pneumatic Li Nom. Operating Press. Li Other Li ExemptZ]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed,- F.R.Sorrow, QA Tech. Support Date 03/22, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have o itinspcte the components

.. /2/Q!7; and state thatdescribed in this Owner's Report during the period to the best of my knowledge and belief, the Owner hAs performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this.

inspection.-

I Jr_,9-,

• erome F Swan Commissions NC1524, N-I Inspector's &6natture National Board, State, Province and Endorsements K Date .. _ _ ,I Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date April 10, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 013 OShared (specify Units ---

3. Work Performed By: Duke Power Company 3a. Work Order #: 591354 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job e Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: FW - Refueling Water 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, l] No 1-MCA-FW-122 Duke Power 20677 N/A N/A N/A 21 Replaced, El Replacement El Yes B El Repaired, 21 No 1-MCA-FW-122 Duke Power 19769 N/A N/A N/A El Replaced, 21 Replacement El Yes C El Repaired, El No El Replaced, El Replacement El Yes D El Repaired, El No El Replaced, El Replacement [E Yes E El Repaired, El No El Replaced, El Replacement El Yes F El Repaired, 0 No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber, load stud, and spherical bearing in eye piece.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -. FL Grass JrQA Tech Specialist Date O.dwnerp*pOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspected the components described in this Owner's Report during the period q_/&LCIL to wa1 -. /Qq'and state that to the best of my knowledge and belief, the Owner has pe-rformed exa'rmina'tions and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury property damage or a loss of any kind arising from or connected with this inspection.

7-t. .- erome F Swan Commissions NC1524, N-I Inspector'sdfig ?7 National Board, State, Province and Endorsements Date _ I--

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 10, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078

.2a. Unit: 0l1 02 03 OShared (specify Units )

3. Work Performed By: Duke Power Company 3a. Work Order #: 591359 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: BB - Steam Generator Blowdown Recycle 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME Il 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0 No 1-MCR-BB-568 Duke Power 14815 N/A N/A N/A 12 Replaced,

]0 Replacement 0 Yes B 0 Repaired, 01 No 1-MCR-BB-568 Duke Power 19899 N/A N/A N/A 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0] Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work -Replaced snubber

8. Tests Conducted:Hydrostatic 2 Pneumatic 0 Nom. Operating Press. El Other 2 Exemptl-Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed

• FL Grass Jr,QA Tech Specialist Date Owner ol'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS.B CThave insp cteo the components described in this Owner's Report during the period u l- /to Z/07 ; and state that to the best of my knowledge and belief, the Owner h s performed 6eamfnations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inj or property damage or a loss of any kind arising from or connected with this 6' inspection.

..- L*_-/

Inspectol-S 'nbature der'm_

.-- F Swan Commissions NC1524, N-I National Board, State, Province and Endorsements i

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date 03/27/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: l0l1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591360-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC Reactor Coolant 4(b) Class of System:

5. (a) Applicable Construction Code: ASME 1111971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, l1No 1MCR-NC-0809 Duke Power 14777 N/A N/A N/A IlJReplaced,

[] Replacement El Yes B 0l Repaired, [INo 1MCR-NC-0809 Duke Power 14864 N/A N/A N/A El Replaced,

_IReplacement El Yes C El Repaired, 0l No 0l Replaced,

__ Replacement El Yes D El Repaired, El No El Replaced,

_ Replacement El Yes E El Repaired, El No 0l Replaced, 0_ Replacement El Yes F El Repaired, El No El Replaced,

[0 Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work PM Snubber Chanqeout

8. Tests Conducted:Hydrostatic L Pneumatic L] Nom. Operating Press. 0 Other U Exempt[Z Pressure _psig Test Temp. OF Pressure psig Test Temp. - OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section X1.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed 4 ALLýaJ F.R. SorrowQA Tech Support Date 03/27, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspocted the components described in this Owner's Report during the period IL6 0 tto =_* *W Y; and state that to the best of my knowledge and belief, the Owner h'as performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Jerome F Swan Commissions NC1524, N-I Inspector's Si nature National Board, State, Province and Endorsements Date "3/12-ý"/V 7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Companyt la. Date April 10, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: Ell 02 03 -Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591361 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, of, ASME Code Stamped Installed (yes or no)

A 0 Repaired, IA No 1 -MCR-NI-510 Duke Power 14861 N/A N/A N/A 21 Replaced, 0 Replacement 0 Yes B 0 Repaired, 21 No 1 -MCR-NI-51 0 Duke Power 20653 N/A N/A N/A 0 Replaced, El Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic E Pneumatic Ii Nom. Operating Press. [] Other LI ExemptI]

Pressure psig Test Temp. OF Pressure psig Test Temp. - OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed __ , FL Grass JrQA Tech Specialist Date *//d 2.92

'Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by 0 CThave ins cted he components described in this Owner's Report during the period

/'-,(07o to L(:2 0 ; and state that to the best of my knowledge and belief, the Owner Kas performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for aispecrasonal injuryr property damage or a loss of any kind arising from or connected with this isetion..

n! /

• /.*.,"0-- ome F Swan Commissions NC1 524, N-I INational Board, State, Province and Endorsements Date .

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date April 3, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #:

Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME 1111971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped

.... _Installed (yes or no)

A 01 Repaired, 0 No 1-MCR-NI-699 Duke Power 20662 N/A N/A N/A 0 Replaced,

[0 Replacement El Yes B 0 Repaired, [] No 1-MCR-NI-699 Duke Power 14874 N/A N/A N/A 0 Replaced, 20 Replacement El Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, [0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0l No 0 Replaced,

[0 Replacement 0 Yes F E Repaired, 0 No 0 Replaced,

]0 Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) sizeis 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt[@

Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed Z" la FL Grass Jr,QA Tech Specialist Date Owner or 9%vner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have nsp ted the components described in this Owner's Report during the period

'~~2to *..*0VT  ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injur r property damage or a loss of any kind arising from or connected with this insp ection / - Z/rom e F S w an C om m issions NC 15 24 , N-I Insp' s gnure National Board, State, Province and Endorsements S DateW9///*t*7 _

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date April 4. 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersvilie. NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591363 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM#: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Spction Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0I No 1-MCR-NI-702 Duke Power 14757 N/A N/A N/A R1 Replaced, 1 O Replacement El Yes B El Repaired, 0 No 1-MCR-NI-702 Duke Power 21082 N/A N/A N/A El Replaced,

[0 Replacement 0l Yes C 0l Repaired, El No 0 Replaced, 0_ Replacement 0 Yes D El Repaired, El No El Replaced,

__ Replacement El Yes E E Repaired, El No El Replaced,

_E Replacement El Yes F- Repaired, El No El Replaced,

__ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber and four bolts with nuts.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptI]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the. report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date 2__

Owner opiwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CThave inspgcted the components described in this Owner's Report during the period

'7 to ZV2 Z.; and state that to the best of my knowledge and belief, the Owner hbas pedrformed exaninations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this inspection.

y-rome F Swan Commissions NC1524, N-I InspectorssSjan t ure National Board, State, Province and Endorsements f Date 4K2 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company 1a. Date 03/22/07 526 S. Church Street, Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 9]1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 00591364-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, [@No 1MCR-NI-0719 Duke Power 20517 N/A N/A N/A 0I Replaced,

]0 Replacement 0 Yes B E0 Repaired, [] No 1MCR-NI-0719 Duke Power 20913 N/A N/A N/A 0 Replaced, IFlReplacement 0 Yes C 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes E 0 Repaired, 0 No 01 Replaced, 01 Replacement 0 Yes F 01 Repaired, 0 No 0 Replaced,

]0 Replacement 0E Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Snubber PM Chanaeout

8. Tests Conducted:Hydrstatic El Pneumatic El Nom. Operating Press. El Other El ExemptlZ]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed*duJ F.R.Sorrow, QA Tech. Support Date 03/22, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by q~qý,have insp cte the components described in this Owner's Report during the period to "Rt/-

2 ;and state that to the best of my knowledge and belief, the Owner Ifas performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this inspection. /

U, *7*'_O_-_/ -rome F Swan Commissions NC1524, N-I 7wnnspector's Sig~tye National Board, State, Province and Endorsements Date ,2-?1 7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 4. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 0]1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591365 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Injection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, El No 1-MCR-NI-744 Duke Power 14850 N/A N/A N/A 21 Replaced, 0E Replacement El Yes B El Repaired, IA No 1-MCR-NI-744 Duke Power 14853 N/A N/A N/A El Replaced, IA Replacement El Yes C El Repaired, 0l No El Replaced, El Replacement El Yes D El Repaired, El No El Replaced, 0E Replacement El Yes E El Repaired, El No El Replaced, 0E Replacement El Yes F El Repaired, El No El Replaced, 0E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic IJ Pneumatic E Nom. Operating Press. -L Other LI Exemptl-Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass JrQA Tech Specialist v0wnerdfOwner's Designee, Title Date __' _

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT ave inspe te the components described in this Owner's Report during the period 2 to / ; and state that to the best of my knowledge and belief, the Owner Ias performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for n**ypersonal injury nspection. .*. or property damage or a loss of any kind arising from or connected with. this

,rome F Swan Commissions NC1524, N-I Inspector')*igature~i National Board, State, Province and Endorsements

1. Date /*.S_*_/,)

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date 03/27/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: i11 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591393-01 Address: 526 6. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC Reactor Coolant 4(b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, E]No 1 MCR-NC-0801 Duke Power 20655 N/A N/A N/A [gReplaced, 0_ Replacement 0l Yes B El Repaired, ZENo 1 MCR-NC-0801 Duke Power 14803 N/A N/A N/A El Replaced,

[]Replacement 0 Yes C El Repaired, E] No o Replaced,

[] Replacement El Yes D El Repaired, El No El Replaced,

_ Replacement El Yes E E- Repaired, 0l No El Replaced, 0_ Replacement El Yes F El Repaired, El No El Replaced, El Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work PM Snubber Chanqeout

8. Tests Conducted:Hydrostatic El Pneumatic 5 Nom. Operating Press. LI Other LI ExemptI[l Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturers Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed i F.R. SorrowQA Tech Support Date 03/27, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspe tedthe components described in this Owner's Report during the period Z/2670? to -3 / "7,and state that to the best of my knowledge and belief, the Owner has performed examinatiorfs and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind-arising from or connected with this inspection.

erome F Swan Commissions NC1524, N-I C

k'Inspector'ei-Ture National Board, State, Province and Endorsements Date T Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date 03/29/2007 526 S. Church Street, Charlotte, NC 28201-1006. Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 0l1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591394 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/_.A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC Reactor Coolant 4(b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 03 Repaired, I9No 1MCR-NC-0811 Duke Power 16577 N/A N/A N/A [I@Replaced, 1 01 Replacement 0 Yes B 0 Repaired, EINo 1 MCR-NC-0811 Duke Power 20242 N/A N/A N/A 01 Replaced,

_IReplacement 0 Yes C 03 Repaired, 0 No 01 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 10 Replacement 0 Yes E 01 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work PM Snubber Chanqeout

8. Tests Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other 0 Exempt[]

Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed F.R. Sorrow,QA Tech Support Date 03/29, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have inspected toe components described in this Owner's Report during the period

!ý to _.3/: o,*,,and state that to the best of my knowledge and belief, the Owner his performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inj or property damage or a loss of any kind arising from or connected with this ispection.

, Jerome F Swan Commissions NC1524, N-I I-" Inspector'i'$*$gnature National Board, State, Province and Endorsements Date 3 t.

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 10, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591395 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 03 No 1 -MCR-NC-813 Duke Power 16564 N/A N/A N/A 12 Replaced,

[0 Replacement 0 Yes B .0 Repaired, 0 No 1-MCR-NC-813 Duke Power 36597 N/A N/A N/A 0 Replaced, E0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt[@

Pressure psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date /L - _

_" wner or'Owners Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have insepcteothe components described in this Owner's Report during the period RV2&107 to L2/07 ; and state that to the best of my knowledge and belief, the Owner h .s performed examinatio'ns and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ncny personal inju r property damage or a loss of any kind arising from or connected with this inspection.

yt . ~-* rome F Swan Commissions NC1524, N-I

/InspectoiWr re National Board, State, Province and Endorsements C Date ý7/"*4-/*.-/7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company 1a. Date 03/27/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: 091 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order# : 00591396-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC Reactor Coolant 4(b) Class of System: A .

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, [No 1 MCR-NC-0900 Duke Power 21939 N/A N/A N/A gReplaced,

]0 Replacement 0 Yes B 0 Repaired, OgNo 1MCR-NC-0900 Duke Power 14921 N/A N/A N/A 0 Replaced,

[_Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 10 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, L0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work PM Snubber Changeout

8. Tests Conducted:Hydrostatic EJ Pneumatic El Nom. Operating Press. El Other El Exempt[]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed t.4-' F.R. SorrowQA Tech Support Date 03/27, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H C have insp cted t er components described in this Owner's Report during the period aQ 7 to  ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for nny personal injury r property damage or a loss of any kind arising from or connected with this spection.

Jerome F Swan Commissions NC1524, N-I Inspector's ure National Board, State, Province and Endorsements C Date ,

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XA

1. Owner Address: Duke Power Company la. Date 03/27/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersvilte, NC 28078 2a. Unit: L911 0-2 03 EShared (specify Units )

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591397-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC Reactor Coolant 4(b) Class of System: .

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998. 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 11 Repaired, []No 1 MCR-NC-0902 Duke Power 20654 N/A N/A N/A I1lReplaced,

_ Replacement El Yes B El Repaired, O1No 1MCR-NC-0902 Duke Power 14785 N/A N/A N/A El Replaced,

[Replacement El Yes C El Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, El No El Replaced, 0E Replacement El Yes E El Repaired, El No El Replaced,

_E Replacement El Yes F E Repaired, El No El Replaced, 0E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work PM Snubber Chanqeout

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt[ll Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A SignedZ F.R. SorrowQA Tech Support Date 03/27, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have insp ced the components described in this Owners Report during the period Z 7 to - "; and state that to the best of my knowledge and belief, the Owner hfs performred examinations and taken corrective measures described in this Owner's Report in accordance with the.requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or conneeted with this inspection. "

/1,ý Jerome F Swan Commissions NC1 524, N-I Inspector's.y1 ature National Board, State, Province and Endorsements Date ZAEZL*V/97 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Companv 1a. Date March 30, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: 0]1 02 03 OShared (specify Units )

3. Work Performed By: Duke Power Company 3a. Work Order #: 591398 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME 1111971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A . . Repaired, 0 No 1-MCR-NC-903 Duke Power 20656 N/A N/A N/A El Replaced,

_E Replacement El Yes B E Repaired, 21 No 1-MCR-NC-903 Duke Power 21476 N/A N/A N/A El Replaced, l] Replacement 0l Yes C El Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, El No El Replaced, 0_ Replacement El Yes E 0 Repaired, El No El Replaced, El Replacement El Yes F 0 Repaired, El No El Replaced,

__ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt!-

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed. FL Grass Jr,QA Tech Specialist Date ,.,

Owner or"Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT- have inspectthe components described in this Owner's Report during the period j ,,70 7 to. 10-7; and state that to the best of my knowledge and belief, the Owner has performed e aminati-ns and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

rome F Swan Commissions NC1524, N-I Inspector's Sig t re National Board, State, Province and Endorsements C Date -3//-7 ,1 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date March 30. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591399 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Inoection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0 No 1-MCR-NI-548 (A) Duke Power 18879 N/A N/A- N/A 0 Replaced,

]0 Replacement El Yes B 0 Repaired, RI No 1-MCR-NI-548 (A) Duke Power 36593 N/A N/A N/A 0 Replaced, El Replacement El Yes C El Repaired, 0 No El Replaced, 0_ Replacement El Yes D El Repaired, El No El Replaced,

__ Replacement El Yes E 0l Repaired, El No 0l Replaced,

__ Replacement El Yes F El Repaired, 0l No El Replaced,

__ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work ReDlaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptIZ Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed

• w FL Grass JrQA Tech Specialist Date 4

-4Z7Z

'ape_2 Owner of Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H ,ave inspe ted jhe=.components described in this Owner's Report during the period 6 to"7 7 3 -/v'7 and state that to the best of my knowledge and belief, the Owner tas performed examidrfations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for

]any personal injury r property damage or a loss of any kind arising from or connected with this

//inspection.

o...... ....* 9Z '--- erome F Swan Commissions NC1524, N-I "Inspector's 4s9gture National Board, State, Province and Endorsements K SDate _.313/0_

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date March 30, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haners Ferry Road. Huntersville. NC 28078 2a. Unit: 211 02 03 I-Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591401 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0. Repaired, 0 No 1-MCR-NI-548 (B) Duke Power 14926 N/A N/A N/A 0l Replaced,

[] Replacement El Yes B El Repaired, 0 No 1-MCR-NI-548 (B) Duke Power 36592 N/A N/A N/A El Replaced, El Replacement El Yes C 0l Repaired, El No El Replaced, 0_ Replacement El Yes D El Repaired, 0l No El Replaced, E

[] Replacement El Yes El Repaired, El No 0l Replaced, F

0_ Replacement El Yes El Repaired, El No El Replaced,

_ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic 0 Pneumatic El Nom. Operating Press. 0l Other El Exemptl]

Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/.A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date ,_ 224ý-*?._

Owner op(Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by L Chave insp ctecjthe components described in this Owner's Report during the period 4U26/07 tom,/-3c>  ; and state that to the best of my knowledge and belief, the Owner has performed examir'atins and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inj*y or property damage or a loss of any kind arising from or connected with this inspection

/ Inspectorsy igatue me F Swan Commissions NC1524, N-I National Board, State, Province and Endorsements

( Date 30 7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date March 30. 2007 526 S. Church Street, Chadotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591402 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. -(a) Identification of System: NI - Safety Iniection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, O No 1-MCR-NI-549 (A) Duke Power 14772 N/A N/A N/A 2 Replaced, 1 E Replacement El Yes B El Repaired, 01 No 1-MCR-NI-549 (A) Duke Power 36591 N/A N/A N/A El Replaced, RI Replacement 0l Yes C El Repaired, El No 0l Replaced, 0_ Replacement El Yes D 0l Repaired, El No El Replaced,

_E Replacement [] Yes E 0l Repaired, 0l No El Replaced, El Replacement El Yes F E Repaired, El No El Replaced,

__ Replacement 0l Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work -Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other 0l ExemptO Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -gV2._,, FL Grass JrQA Tech Specialist Date - __

V*Ov"ner or Ow'ner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION i, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspected the components described in this Owner's Report during the period z*0iiZ to 3/V 1767; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's

/

Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for 1iy personal injury r property damage or a loss of any kind arising from or connected with this lspecton.

'/1*,"derome F Swan Commissions NC1524, N-I

/Inspector's SiWaur, National Board, State, Province and Endorsements Soate-_0.D Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date March 30, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591403 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job 4 Type Code Symbol Stamp: N/A Authorization No. N/.A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Injection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME I111971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0 No 1-MCR-NI-549 (B) Duke Power 14888 N/A N/A N/A E0 Replaced, 0 Replacement 0 Yes B 0 Repaired, E0 No 1-MCR-NI-549 (B) Duke Power 36594 N/A N/A N/A 0 Replaced, 0l Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work ReDlaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptI]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed - FL Grass JrQA Tech Specialist Date ___

Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have inspcted the components described in this Owner's Report during the period Z14L102 to Lw Q '7; and state that to the best of my knowledge and belief, the Owner has pehormed examinations -and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury -'property damage or a loss of any kind arising from or connected with this inspectilon. /..

I rome F Swan Commissions NC1524, N-I SInspector's igntc National Board, State, Province and Endorsements Dsate ***/)*

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date March 30, 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 021 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591404 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A [0 Repaired, 0 No 1-MCR-NI-569 (A) Duke Power 20245 N/A N/A N/A 0 Replaced,

]0 Replacement 0 Yes B 0 Repaired, RI No 1-MCR-NI-569 (A) Duke Power 36596 N/A N/A N/A 0 Replaced, EI Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced, 0] Replacement 0 Yes D 0 Repaired, 0 No D Replaced,

,0[O Replacement 0 Yes E 0 Repaired, 0 No O Replaced,

[o Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic 5 Pneumatic 5 Nom. Operating Press. 0 Other LI ExemptL]

Pressure psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify.that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed v FL Grass JrQA Tech Specialist Date ____

""Orwner or'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H insp ct~l the components described in this Owner's Report during the period Q/ `to/-/ 0 "7;and state that to the best of my knowledge and belief, the Owner h ~speiormed ex'anrinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, -concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ny personal injury or roperty damage or a loss of any kind arising from or connected with this npctilon, f me F Swan Commissions NC1 524, N-I

-Inspector's ,g National Board, State, Province and Endorsements Da te D ,. * * .*

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date March 30, 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: E1 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591405 Address: 526 S. Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, 0 No 1-MCR-NI-569 (B) Duke Power 19906 N/A N/A N/A 0 Replaced, I_ 1 Replacement 0 Yes B El Repaired, 0 No 1-MCR-NI-569 (B) Duke Power 36595 N/A N/A N/A El Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0l No 0 Replaced,

[0 Replacement El Yes D El Repaired, 0 No C1 Replaced,

__ Replacement 0 Yes E 0l Repaired, El No El Replaced,

__ Replacement El Yes F [I Repaired, El No Cl Replaced, 0_ Replacement 1l Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work ReDlaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptRi Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed ,-* FL Grass JrQA Tech Specialist D ate 1i V SOwner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspqcthd te components described in this Owner's Report during the period

/2G/o to t/i QjO 7 ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this ome F Swan Commissions NC1524, N-I rer-ispector National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Comoany la. Date April 3. 2007 526 S. Church Street. Charlotte, NC 28201-1006 Sheet 1 of 1.

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 I-Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591406 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/.A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0Z No 1-MCR-NI-717 Duke Power 21782 N/A N/A N/A 0Z Replaced, El Replacement El Yes B E Repaired, 12 No 1-MCR-NI-717 Duke Power 36584 N/A N/A N/A El Replaced, E0 Replacement El Yes C El Repaired, El No El Replaced, 0_ Replacement El Yes D El Repaired, El No El Replaced, El Replacement El Yes E El Repaired, El No El Replaced, El Replacement El Yes F 0l Repaired, El No 0l Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber and bolting on end bracket.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct andthis conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed. FL Grass JrQA Tech Specialist Date Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by

,SB.CT have 1 't~ l the components described in this Owner's Report during the period 7 to L110 "7 and state that to the best of my knowledge and belief, the Owner Ias 1ierformed examinations and taken corrective measures described in this Owners Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injuryir property damage or a loss of any kind arising from or connected with this inspection."

Si

=me F Swan Commissions NC1524, N-I Inspector',,S ure National Board, State, Province and Endorsements I

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 10, 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: [01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 591407 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Ingection 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 11 Repaired, 03 No 1-MCR-NI-850 Duke Power 20549 N/A N/A N/A 0 Replaced, 0o Replacement El Yes B El Repaired, 0 No 1-MCR-NI-850 Duke Power 14778 N/A N/A N/A El Replaced,

]0 Replacement El Yes C El Repaired, El No El Replaced, El Replacement El Yes D 0 Repaired, El No O Replaced,

__ Replacement El Yes E 0l Repaired, El No El Replaced,

__ Replacement El Yes F 0l Repaired, El No

[] Replaced,

__ Replacement [] Yes Page 1 of 2

.Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other LI Exempt[Z Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct andthis conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date... 7 7 O*wner o(Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CThave the components described in this Owner's Report during the period 21P.41 0t to /oL"; and state that to the best of my knowledge and belief, the Owner h s perormed ex'aminrations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Zy ,/ -- Jerome F Swan Commissions NC1524, N-I Inspectors gýrr ure National Board, State, Province and Endorsements I

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date March 30. 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 102 013 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591408 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0 No 1-MCR-NI-852 Duke Power 14843 N/A N/A N/A 0 Replaced,

__ Replacement El Yes B El Repaired, 0I No 1-MCR-NI-852 Duke Power 36583 N/A N/A N/A El Replaced, EI Replacement El Yes C 0l Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, El No El Replaced,

_ Replacement El Yes E El Repaired, El No El Replaced, 0E Replacement 0l Yes F E Repaired, El No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl*

Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/._A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass JrQA Tech Specialist Date .

"( ner or,6wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspqcte4the components described in this Owner's Report during the period a "0 to-.31/1*Z7 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury property damage or a loss of any kind arising from or connected with this

-=Jerome F Swan Commissions NC1524, N-I Inspector'slSt*1n tre National Board, State, Province and Endorsements I

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 4. 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591409 Address: 526 S. Church Street, Charlotte NC 2820.1-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/AA Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: NI - Safety Iniection 4. (b) Class of System: -B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, 21 No 1-MCR-NI-879 Duke Power 14910 N/A N/A N/A E1 Replaced,

[O Replacement 0 Yes B 0 Repaired, 10 No 1 -MCR-NI-879 Duke Power 17401 N/A N/A N/A 0 Replaced, 21 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0l Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptrO Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed *. - 14/I.FL

-- Grass JrQA Tech Specialist Date / v _ __

• /I Owner orw)wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by C have insp cteid the components described in this Owner's Report during the period

-to tos 4/4t/7 to ; and test ot of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this Ainspection.

rome F Swan Commissions NC1524, N-I Dcatey//5 Inspector's Sign .ure National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Companv la. Date April 11.2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville. NC 28078 2a. Unit: 1031 02 03 -Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591415 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NF - Ice Condenser Refrigeration 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, RI No 1-MCR-S-NF-100- Duke Power 17372 N/A N/A N/A 01 Replaced, 01-0 10 Replacement El Yes B El Repaired, 01 No 1-MCR-S-NF-100- Duke Power 14809 N/A N/A N/A El Replaced, 01-0 _ 0 Replacement 0l Yes C El Repaired, El No 0l Replaced,

__ Replacement 0l Yes D [] Repaired, El No El Replaced, 0_ Replacement El Yes E El Repaired, El No El Replaced,

__ Replacement El Yes F El Repaired, El No 0- Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed

• _ FL Grass Jr,QA Tech Specialist Date - ,44 '.2_

SOwvneroq.Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H CT have inspcte* the components described in this Owner's Report during the period 2 'LZ / toO Zto 7' ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, .expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injurypr property damage or a loss of any kind arising from or connected with this inspection.

"-'.-" Jerome F Swan Commissions NC1524, N-I spector's ure National Board, State, Province and Endorsements C Date Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 10, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: 021 02 03 OShared (specify Units .)

3. Work Performed By: Duke Power Company 3a. Work Order #: 591417 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: VX - Containment Air Return Exhaust and Hydrogen Skimmer 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 0 No 1-MCR-S-VX-100- Duke Power 20904 N/A N/A N/A 0I Replaced, 01-HH _0 Replacement 0 Yes B 0 Repaired, 0 No 1-MCR-S-VX-100- Duke Power 20589 N/A N/A N/A 0 Replaced, 01-HH _0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

'_. ___ Replacement 0 Yes F 0 Repaired, 5 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber, 3/8" bolts and nuts.

8. Tests Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. 0 Other 0 ExemptI]

Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date /0 2 Own/Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed .by HSB CT have inspe ted Ihe components described in this Owner's Report during the period

,7/ 1 t2'7 to I.L'.. and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for

• any personal inju r property damage or a loss of any kind arising from or connected with this

• inspection. * ..

u¢--

. L--Jerome F Swan Commissions NC1524, N-I Inspector' S'la e National Board, State, Province and Endorsements SDateV // -a-1/(*_._7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date Apri 11.2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 E]Shared (specify Units .)

3. Work Performed By: Duke Power Company 3a. Work Order # : 591418 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/AA Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: VX - Containment Air Return Exhaust and Hydrogen Skimmer 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME 111 1971 Edition,. Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 01 No 1-MCR-S-VX-100- Duke Power 20545 N/A N/A N/A RI Replaced, 01-JJ _ Replacement El Yes B El Repaired, 0] No 1-MCR-S-VX-100- Duke Power 21842 N/A N/A N/A El Replaced, 01-JJ R_ Replacement El Yes C El Repaired, El No El Replaced,

__ Replacement El Yes D 0l Repaired, 0l No El Replaced,

__ Replacement El Yes E 0l Repaired, El No 0l Replaced,

__ Replacement 0l Yes F El Repaired, El No El Replaced,

__ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Redlaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic LI Nom. Operating Press. [1 Other El ExemptrZ Pressure psig Test Temp. OF Pressure .psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/_A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date t'/ _

"' _Owner Q4'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by C have inspe, the components described in this Owner's Report during the period LP 0j7 to &ý/2/,77 and state that to the best of my knowledge and belief, the Owner has pIerformed exAminhations and taken corrective measures described in this Owner's Report In accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for

,any personal inju or property damage or a loss of any kind arising from or connected with this inspection. -

, , Jerome F Swan Commissions NC1524, N-I

( / Inspector's'%6natre Date 1112-70,17 National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Comoany la. Date 03(22(07 526 S. Church Street, Charlotte, NC 282011-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 013 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 00591439-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: BB Steam Generator Blowdown Recycle 4.b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, rgNo 1MCR-BB-0537 Duke Power 00120 N/A N/A N/A 19 Replaced,

_0 Replacement 0 Yes B 0 Repaired, []No 1 MCR-BB-0537 Duke Power 18159 N/A N/A N/A 0 Replaced,

_IReplacement El Yes C 0 Repaired, 0 No 0l Replaced, 0] Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Snubber PM Chanae out

8. Tests Conducted:Hydrostatic El Pneumatic 0l Nom. Operating Press. El Other El Exempt[M Pressure _psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed- F.R.Sorrow, QA Tech. Support Date 03/22, 2007 Owner or Owners Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspectedthe components described in this Owner's Report during the period 92o-7 to 317.U617; and state that to the best of my knowledge and belief, the Owner his performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this

( _inspection.-'*

rome F Swan Commissions NC1524, N-I SInspector's 8i ature National Board, State, Province and Endorsements C Date ___

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR /.REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 4, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: I01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591440 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: BB - Steam Generator Blowdown Recycle 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998., 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg- Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, IA No 1-MCR-BB-561 Duke Power 21672 N/A N/A N/A I2 Replaced,

]0 Replacement 0 Yes B .0 Repaired, 0A No 1-MCR-BB-561 Duke Power 36588 N/A N/A N/A 0 Replaced,

__ Replacement 0 Yes C El Repaired, 0 No El Replaced, 0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[O Replacement 0 Yes E 0 Repaired, 0 No 0l Replaced,

__ Replacement 0 Yes F El Repaired, El No O Replaced,

[] Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work- inlInnrit cni hhinr t:!

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptlZ Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed ,*\ .O FL Grass JrQA Tech Specialist Date.. * -i

,Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by Ts have htecomponents described in this Owner's Report during the period I '7z. to *tI, 0  ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injuff or property damage or a loss of any kind arising from or connected with this inspection.

2*,-'.* L--- AdJome F Swan Commissions NC1524, N-I Inspector' ig ture National Board, State, Province and Endorsements I.

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 4, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591442 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: - BB - Steam Generator Blowdown Recycle 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class.MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, 0 No 1-MCR-BB-567 Duke Power 20514 N/A N/A N/A 01 Replaced, I 1 0 Replacement El Yes B El Repaired, 0 No 1-MCR-BB-567 Duke Power 36586 N/A N/A N/A 0 Replaced,

]0 Replacement 0l Yes C El Repaired, El No El Replaced,

]0 Replacement 0 Yes D El Repaired, El No El Replaced,

[0 Replacement El Yes E 0 Repaired, El No El Replaced, El Replacement El Yes F El Repaired, El No 0 Replaced,

__ Replacement 0l Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt[Z Pressure psig Test Temp. OF Pressure _psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's. Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed "*, FL Grass JrQA Tech Specialist Date owner or 6wner's Designee, Title

• CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspe te the components described in this Owner's Report during the period (64Q:7 to -Q-  ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju' or property damage or a loss of any kind arising from or connected with this inspection. / ..

,,-,-* erome F Swan Commissions NC1524, N-I Inspector's*ture National Board, State, Province and Endorsements 6 Date

-4k 1*.//)7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date April 4, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferrv Road. Huntersville. NC 28078 2a. Unit: 01 02 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591443 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/_AA Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: BB - Steam Generator Blowdown Recycle 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, E1 No 1-MCR-BB-645 Duke Power 129 N/A N/A N/A 0I Replaced, I_1 0 Replacement 0 Yes B 0 Repaired, E0 No 1-MCR-BB-645 Duke Power 36589 N/A N/A N/A El Replaced, E1 Replacement El Yes C 0 Repaired, El No 0 Replaced,

[0 Replacement El Yes D El Repaired, El No El Replaced,

[0 Replacement El Yes E El Repaired, El No El Replaced,

_ _ Replacement El Yes F E Repaired, El No El Replaced,

__ Replacement 1l Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work -Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptlO Pressure psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Sioned FL Grass Jr.OA Tech Soecialist Date -V Owner or-)wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspecteo the components described in this Owner's Report during the period

/3/- tot-LW4 :7; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injuryr property damage or a loss of any kind arising from or connected with this inspection. */.

rome F Swan Commissions NC1524, N-I

/Inspector's S ure National Board, State, Province and Endorsements 6 / Date //*,7_

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company la. Date March 30, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 211 - 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order#: 591444 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: CA - Auxiliary Feedwater 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME 111 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, El No 1-MCR-CA-445 Duke Power 20546 N/A N/A N/A 0 Replaced,

]0 Replacement 0 Yes B 0 Repaired, 0l No 1-MCR-CA-445 Duke Power 36582 N/A N/A N/A 0 Replaced, R0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work ReDlaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exempt[Z Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass JrQA Tech Specialist Date ,/ a-,. _

Owner c*"`Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H ave insp cted the components described in this Owner's Report during the period

)n-j72 to m  ; and state that to the best of my knowledge and belief, the Owner has performed e.amih ations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury r property damage or a loss of any kind arising from or connected with this inspection.

"/ Inspector's /S~no ue F Swan Commissions Na4terrome NC1524, N-c National Board, State, Province and Endorsements

/Date *-3Tý/*5/ f)

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date 03/27/2007 526 S. Church Street, Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville, NC 28078 2a. Unit: I11 02 03 DShared (specify Units .)

3. Work Performed By: Duke Power Company 3a. Work Order # :00591531-01 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Iniection 4(b) Class of System: A,,,..

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, IgNo 1MCR-NI-0515 Duke Power 15866 N/A N/A N/A [gReplaced,

_0 Replacement 0 Yes B 0 Repaired, ZNo 1MCR-NI-0515 Duke Power 15872 N/A N/A N/A 0 Replaced,

[]Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 01 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work PM Snubber Chanqeout

8. Tests Conducted:Hydrostatic E Pneumatic E] Nom. Operating Press. El Other El Exempt[g Pressure _psig Test Temp. OF Pressure psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed 1-,, F.R. SorrowQA Tech Support Date 03/27, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by iBChave insp the components described in this Owner's Report during the period a/ "~Z7 to Z./ ,; and state that to the best of my knowledge and belief, the Owner htas'performed exarTinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injuryor property damage or a loss of any kind arising from or connected with this

• spectioln.f

- rome F Swan Commissions NC1524, N-I SInspector' Si ElDatel/./),'/7 ure National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Company Ia. Date Seotember 17, 2006 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Comoany 3a. Work Order #: 591575 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM # N/A

4. (a) Identification of System: NS - Containment Spray 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME 11 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0 No NS System Duke Power N/A 40 N/A 1981 0 Replaced, 0 Replacement 0 Yes B o Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

"___0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

...._ __0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

____ Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced bolting material at instrument flange 1NSFE5030

8. Tests Conducted:Hydrostatic 0 Pneumatic 5 Nom. Operating Press. l] Other 0 ExemptO Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks ReDlaced boltina one at a time.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr.QA Tech Specialist Date 7Z _.=.

bwner o(Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by C have inspected the components described in this Owner's Report during the period RII&to -; and state that to the best of my knowledge and belief, the Owner has rformed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this

/inspection, e me F Swan Commissions NC1524. N-i inspeclor's/,gn ure National Board, State, Province and Endorsements Date7/

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date September 17, 2006 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 OlShared (specify Units )

3. Work Performed By: Duke Power Company 3a. Work Order #: 591576 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NS - Containment Spray 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME 11 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 01 No NS System Duke Power N/A 40 N/A 1981 12 Replaced,

[0 Replacement RI Yes B 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 11 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced bolting material at instrument flange 1NSFE5020

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. IA Other El Exempt[]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks Renlaced boltina one at a time.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr.QA Tech Specialist Date Owner or"Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS CT have insctedthe components described in this Owner's Report during the period 87-A&,toto./L  ; and state that to the best of my knowledge and belief, the Owner hispdrformed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Jerome F Swan Commissions NC1524, N-I Inspector'V"anature National Board, State, Province and Endorsements 6 Date - V*)/' (/P Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section Xl

1. Owner Address: Duke Power Comoany la. Date March 30, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station . -

12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 -Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591597 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A- Authorization No. N/_A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: CF - Feedwater 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, RI No 1-MCR-CF-405 Duke Power 33796 N/A N/A N/A 0 Replaced,

]0 Replacement 0 Yes B 0 Repaired, 0 No 1-MCR-CF-405 Duke Power 33625 N/A N/A N/A 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 03 No 0 Replaced,

_ Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No O Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic EJ Pneumatic 5 Nom. Operating Press. El Other 0l ExemptI]

Pressure _ psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed \ezg.'/ FL Grass JrQA Tech Specialist Date -41ý01.*_._

Owner or Owner's Designee, Title //

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspectfd the components described in this Owner's Report during the period

• z,-6-..'to qILI.02  ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal i jury or property damage or a loss of any kind arising from or connected with this

(}inspection.-- "

f erome F Swan Commissions NC1 524, N-I SInspecto ISig ature National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 4, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferrn Road. Huntersville, NC 28078 2a. Unit: 21 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 591910 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: ME100776

4. (a) Identification of System: NS - Containment Spray 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 01 No NS System Duke Power N/A 40 N/A 1981 0 Replaced, 21 Replacement 0] Yes B 0 Repaired, 0 No 0 Replaced,

__ Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced, I 10 Replacement 10 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced 8" SS Pipingq on 1B, 1B1, and 1B2 per ME100776 between elevations 765 and 775.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. L] Other IZ ExemptEl Pressure 15 psig Test Temp. 73.1 OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed & 9 Z FL Grass Jr.QA Tech Specialist Date Owner orwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspe the components described in this Owner's Report during the period aIJax-2**7 to and state that to the best of my knowledge and belief, the Owner

Z,2Ji; h s performed ex mfnations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this nspection.

'r.LL- Jerome F Swan Commissions NC1524, N-I nspector's IS* ture National Board, State, Province and Endorsements C Date 07 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 29, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 0Shar~d (specify Units

3. Work Performed By: Duke Power Comoany 3a. Work Order #: 591910 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: ME 100776

4. (a) Identification of System: NS - Containment Spray 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda; N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 0 No 1-MCR-NS-751 Duke Power N/A N/A N/A N/A 0 Replaced, RI Replacement 01 Yes B 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement El Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0l Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replacement of hanqer after ME100776 was in place.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl]

Pressure _psig Test Temp. OF Pressure psig Test Temp. _ OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed - .. j- , FL G rass Jr.Q A Tech Specialist Date tw-ner oq'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have i pe ted, , ecom ponents described in this Owner's Report during the period L11181 7 to"to and

'I2

, state that to the best of my knowledge and belief, the Owner hK's perfofrmed exaaminations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

n.'.Jrome F Swan Commissions NC1524, N-i Inspector's i gtre National Board, State, Province and Endorsements Dater"s Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date March 30. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haoers Ferry Road. Huntersville. NC 28078 2a. Unit: 01 02 E13 OlShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 595413 Address: 526 S. Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: FW - Refueling Water 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0J Repaired, 21 No 1-MCR-FW-125 Duke Power 19157 N/A N/A N/A 0] Replaced, 1 0 Replacement 0 Yes B 0 Repaired, IA No 1-MCR-FW-125 Duke Power 16540 N/A N/A N/A 0 Replaced, I IAReplacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D -0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 00 Repaired, 0 No Replaced, 0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 10 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl-Pressure _psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date 2q01 Owner or`Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspe the components described in this Owner's Report during the period X/ I--'7' to ,/{7 ; and state that to the best of my knowledge and belief, the Owner

-//*

has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

me F Swan Commissions NC1524, N-I Inspector's Sigr e National Board, State, Province and Endorsements Date J-Lý / Z Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 4. 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haners Ferry Road. Huntersville. NC 28078 2a. Unit: 0l1 [12 03 DShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1699266 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NS - Containment Spray 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 11 No 1-NS-39 Kerotest FW8-17 6732 N/A 1975 El Replaced,

, R1 Replacement 0 Yes B El Repaired, El No El Replaced,

_E Replacement 0l Yes C El Repaired, E0 No 0l Replaced,

_ _Replacement 0l Yes D 0l Repaired, El No El Replaced,

_ Replacement El Yes E E Repaired, 0l No El Replaced,

__ Replacement El Yes F E Repaired, El No 0l Replaced,

__ Replacement 0l Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced disc.

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. I] Other Li Exempt[]

Pressure <50 psig Test Temp. 73.1 OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks test performed per MNT visual functional by task 02.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed ekama FL Grass Jr,QA Tech Specialist Date .t5-A/,- 2o__

"Owner oroOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have inspe the components described in this Owner's Report during the period

/Ito toZ0 0!7; and state that to the best of my knowledge and belief, the Owner h&sperformed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore neither the Inspector nor his employer shall be liable in any manner for any personal injury inspection. / property

.~ damage or a loss of any kind arising from or connected with this rome F Swan Commissions NC1524, N-I "Inspector'sSi re National Board, State, Province and Endorsements T Date ..7_ 7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date 04/05/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 0]1 102 03 OShared (specify Units

3. Work Performed By: Duke Power Company- 3a. Work Order# :01714956 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Injection 4.(b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0 No 1NI-184B Walworth C-55815 168 Valve 1974 0 Replaced,

___Replacement Z]Yes B 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, 1 0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement .0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced Bonnet to Body studs and Nuts

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. [1 Other El Exempt[]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/_.A Certificate of Authorization No. N/A Expiration Date N/A Signed- F.R. SorrowQA Tech Support Date 04/05, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H§B T have te-the components described in this Owner's Report during the period SL//"7)to7 t 07L/; and state that to the best of my knowledge and belief, the Owner

-as 'perfor'med exarTfati6ns and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for Lny personal injurpr property damage or a loss of any kind arising from or connected with this inspection.

SzA, -Jerome F Swan Commissions NC1524, N-I Inspector'srigAUre National Board, State, Province and Endorsements I

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 25, 2007 526 S. Church Street, Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: 101 02 03 -iShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1716964 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job A Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD100346

4. (a) Identification of System: NS - Containment Spray 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 0 No 1-MCA-NS-23 Duke Power N/A N/A N/A N/A 0 Replaced, I 1 0 Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced,

__ Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, 11 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Modified hancger per MD100346

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptl-I Pressure _psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed ,-FL Grass JrQA Tech Specialist Date ___

Owner or e'wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have tedhe components described in this Owner's Report during the period

&7. to //27.o,'; and state that to the best of my knowledge and belief, the Owner hf.s performed e,(amirfations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for Aany personal injury r property damage or a loss of any kind arising from or connected with this inspection. Y/

L erome F Swan Commissions NC1524, N-I Inspector rSV(re National Board, State, Province and Endorsements C Date 21*4.6vy 7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date 05/01/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: I11 0-2 03 0-Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 01716964/54 Address: 526 S. Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD100346

4. (a) Identification of System: NS Containment Spray 4.(b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A E3 Repaired, 0l No 1NS-165 Velan Inc. 062036 N/A Valve 2006 El Replaced,

[@Replacement fflYes B 0 Repaired, 0l No 0l Replaced, OReplacement rlYes C El Repaired, El No Piping Duke Energy N/A 40 1NS 1981 El Replaced,

__ Replacement Z]Yes D El Repaired, El No El Replaced,

_E Replacement El Yes E El Repaired, El No El Replaced, El Replacement El Yes F E Repaired, El No El Replaced,

_E Replacement [E Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Added Valve and pipingq per MD100346

8. Tests Conducted:Hydrostatic LI Pneumatic El Nom. Operating Press. 19 Other El Exemptl Pressure Suction 44 psig Test Temp. 80 OF Pressure Disch. 223 psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed;X -ja&4Z F.R. SorrowQA Tech Support Date 05/01, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have tegl the components described in this Owner's Report during the period I1/1410 to A,/027; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for ny personal injury o roperty damage or a loss of any kind arising from or connected with this I nspection.

menspector, F Swan Commissions NC1524, N-I Inspector's Sig u National Board, State, Province and Endorsements V Dates.

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date 05/01/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haners Ferry Road. Huntersville. NC 28078 2a. Unit: 0]1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 01716964/55 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD100346

4. (a) Identification of System: NS Containment Spray 4.(b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 0 No 1NS-1 66 Velan Inc. 062038 N/A Valve 2006 01 Replaced, lReplacement IlYes B 0 Repaired, 0 No 0 Replaced, OReplacement DYes C 0 Repaired, 0 No Piping Duke Energy N/A 40 iNS 1981 0 Replaced,

_ _Replacement

_ 9Yes D 0 Repaired, 0 No 01 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page I of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Added Valve and piping per MD100346

8. Tests Conducted:Hydrostatic 0 Pneumatic 5 Nom. Operating Press. [1 Other 0 ExemptS Pressure Suction 41 psig Test Temp. 80 OF Pressure Disch. 230 psig Test Temp. OF Pressure _ _ psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed .",,&_.-,,F.R. Sorrow,QA Tech Support Date 05/01, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS3CT have inspected the components described in this Owner's Report during the period S*./IL/07 tom-'///0  ; and state that to the best of my knowledge and belief, the Owner has pe'rformed exminations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injuy or property damage or a loss of any kind arising from or connected with this i tnspectio n.../.. .

ý Jerome F Swan Commissions NC1524, N-I

/ I'nspector's Si~ature National Board, State, Province and Endorsements Date./Z/W. 7 s

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 14, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: E1l 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 1730551 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, 01 No 1-NC-VA-2 Crosby 56925-00-0003 27 N/A 1974 12 Replaced,

]0 Replacement RI Yes B 0 Repaired, 0 No 1-NC-VA-2 Crosby 56925-00-0008 524 N/A 1978 0 Replaced, 121 Replacement RI Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 01 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

_ [_0 Replacement 0 Yes Page 1 of 2

i--ormn NI, (baCK)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Reolaced valve

8. Tests Conducted:Hydrostatic E Pneumatic 0] Nom. Operating Press. l] Other LI Exemptol Pressure 2235 psig Test Temp. 558 °F Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks test performed per MP/O/A/7650/076 under w/o# 589246.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed ",4 4 4142 FL Grass JrQA Tech Specialist Date . ,-,=*

Owner or-Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspected the components described in this Owner's Report during the period 27 to 5/h6/'7; and state that to the best of my knowledge and belief, the Owner has performed exdmintio9ns and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this Snspection.

£ 'U-erome F Swan Commissions NC1 524, N-I f "Inspector's

.Bfn ture National Board, State, Province and Endorsements

( Dates/ _* 7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 22, 2007 526 S. Church Street, Charlotte, NC 28201-1006W Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hapers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1730552 Address: 526 S. Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/_A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NC - Reactor Coolant 4. (b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped

_ Installed (yes or no)

A El Repaired, 11 No 1-NC-VA-3 Crosby 56925-00-0001 25 N/A 1974 0 Replaced, B 0 Replacement 0 Yes B E0 Repaired, 0l No 1-NC-VA-3 Crosby 56925-00-0009 525 N/A 1978 El Replaced, E0 Replacement 0 Yes C El Repaired, El No El Replaced, El Replacement El Yes D El Repaired, 0l No El Replaced, El Replacement El Yes E El Repaired, El No El Replaced, F E Replacement El Yes 0E Repaired, El No El Replaced,

_ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Reolaced valve

8. Tests Conducted:Hydrostatic 0l Pneumatic El Nom. Operating Press. l] Other El Exempti Pressure 2235 psig Test Temp. 558 OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks test performed per MP/O/A/7650/076 under w/o# 589246.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date .49*/ _2-Ov~ner oKrOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have inspted the components described in this Owner's Report during the period to _-5 ",7; and state that to the best of my knowledge and belief, the Owner Mas performed ex(mrinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this inspection. /

g ,* -'r.e-Jerome F Swan Commissions NC1524, N-I

/ nspector's g lure National Board, State, Province and Endorsements

/Date.."t'/*

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date May 8. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 0l1 02 03 0 Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1732837 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD1 00642

4. (a) Identification of Systern: NV - Chemical and Volume Control 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer andWinter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 0l No 1NV482 Dresser TE09052 263 N/A 1978 EI Replaced,

[0 Replacement 0 Yes B 0 Repaired, 0 No NV System Duke Power N/A 37 N/A 1981 0 Replaced, 20 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page I of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Removed Valve 1NV482 and aded piping per MD1 00642.

8. Tests Conducted:Hydrostatic 0 Pneumatic 0 Nom. Operating Press. I] Other U ExemptE Pressure 27 psig Test Temp. 88 OF Pressure _psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks test performed per procedure MP/0/A/7650/076.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -ýý a FL Grass Jr,QA Tech Specialist Date * '*,o' Owner efr Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS Thave teF the components described in this Owner's Report during the period q/1/0?to t.*-*,, 4Z; and state that to the best of my knowledge and belief, the Owner hA'peroimed exa.minations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury r property damage or a loss of any kind arising from or connected with this f*inspection. /

-J-erome F Swan Commissions NC1524, N-I Inspector's re National Board, State, Province and Endorsements

( / Date _

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date May 8, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1732869 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job N Type Code Symbol Stamp: -N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD100642

4. (a) Identification of System: NV - Chemical and Volume Control 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed lyes or no)

A El Repaired, 0l No 1 NV486 Dresser TE09056 267 N/A 1978 0 Replaced, 1 Replacement 0 Yes B El Repaired, El No NV System Duke Power N/A 37 N/A 1981 0l Replaced, 0 Replacement 0 Yes C El Repaired, 0l No El Replaced,

_E Replacement El Yes D El Repaired, El No El Replaced,

_E Replacement El Yes E El Repaired, El No El Replaced,

_E Replacement El Yes F El Repaired, El No El Replaced, 0E Replacement El Yes Page 1 of 2

Form NIS-2 (Beick)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Removed Valve 1NV476 and aded piping per MD100642.

8. Tests Conducted:Hydrostatic El Pneumatic 5 Nom. Operating Press. [a Other 0 Exempto Pressure 27 psig Test Temp. 88 OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks test performed per procedure MP/0/A/7650/076.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass JrQA Tech Specialist Date-* , 2 Owner pYOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by

.._.*_ T have inspe tedthe components described in this Owner's Report during the period Z "JLJQ7to  ; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this inspection.

2-',.Jerome F Swan Commissions NC1524, N-I Inspector ig ture National Board, State, Province and Endorsements 1

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date May 8, 2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hapers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 E32 03 DShared (specify Units

3. Work Performed By: Duke Power Comoany 3a. Work Order#: 1732931 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD1 00642

4. (a) Identification of System: NV - Chemical and Volume Control 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, E0 No 1NV487 Dresser TE09058 269 N/A 1978 0 Replaced, 0 Replacement 0 Yes B 0 Repaired, 0 No NV System Duke Power N/A 37 N/A 1981 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Removed Valve 1NV487 and aded pipingq per MD100642.

8. Tests Conducted:Hydrostatic Li Pneumatic LI Nom. Operating Press. WI Other Li ExemptE Pressure 27 psig Test Temp. 88 OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks test performed per procedure MP/O/A/7650/076.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date / o7 Owner 6r Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have nspected the components described in this Owner's Report during the period

-3, to -S.9,,*L ,7;and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this

!inspection" .

,-. , J me F Swan Commissions NC1524, N-I -

National Board, State, Province and Endorsements

(

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date 04/14/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 011 02 03 OShared (specify Units

3. Work Performed By: Duk6 Power Company 3a. Work Order#: 01737115 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM#:MD1 00802

4. (a) Identification of System: ND Residual Heat Removal 4.(b) Class of System: A

5. (a) Applicable Construction Code: ASME 111.1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, [ONo 1-MCR-ND-0508 Duke Energy N/A N/A Hanger N/A 0 Replaced, I__Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced, 0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

]0 Replacement 01 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Modified Hanger 1-MCR-ND-0508 Per MD100802.

8. Tests Conducted:Hydrostatic El Pneumatic LI Nom. Operating Press. LI Other LI Exempt[]

Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed - At- F.R. SorrowQA Tech Support Date 04/14, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I,the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HS5 CT-have *pted ;e components described in this Owner's Report during the period to *z'2

'LII-51/ 7"; and state that to the best of my knowledge and belief, the Owner M~s performed e'('miriations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury property damage or a loss of any kind arising from or connected with this inspection..

. ".Jerome F Swan Commissions NC1524, N-I Inspector's r ~a rNational Board, State, Province and Endorsements Date i ,/

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section X1

1. Owner Address: Duke Power Company la. Date May 13, 2007 526 S. Church Street, Charlotte, NC 28201-1006. Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: 0`1 E12 03 bShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1739915 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date:. N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NS - Containment Spray 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, El No 1NS1 Walworth A0323 10 N/A 1973 El Replaced,

[0 Replacement RI Yes B E Repaired, El No El Replaced, 0_ Replacement El Yes C El Repaired, El No El Replaced,

__ Replacement El Yes D El Repaired, El No El Replaced,

_ Replacement El Yes E E Repaired, El No El Replaced, 0_ Replacement El Yes F E Repaired, El No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Renlaced bonnet nuts

8. Tests Conducted:Hydrostatic [J Pneumatic LI Nom. Operating Press. El Other LI Exemptl-Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks Exempted from pressure test per ASME Code Section XI (Interpretation X1 89-08).

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -_06,2ý ' FL Grass Jr,QA Tech Specialist Date -=f/'V7 Owner *lwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by av inspe tedthe components described in this Owner's Report during the period to I//D ,and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for nyspection./zf personal injury or property damage or a loss of any kind arising from or connected with this erome F Swan Commissions NC.1524, N-I Date/Y/

Inspector's 9"gqture National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 22, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700. Haners Ferry Road. Huntersville. NC 28078 2a. Unit: 01 02 03 E-Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1741867 Address: 526 S. Church Street. Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: KC - Component Cooling 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, 01 No 1-MCR-KC-749 Duke Power N/A N/A N/A N/A El Replaced, 1] Replacement El Yes B El Repaired, El No O Replaced,

[] Replacement El Yes C El Repaired, 0l No El Replaced,

_E Replacement 0l Yes D 0 Repaired, El No O Replaced,

__ Replacement El Yes E El Repaired, El No El Replaced, 0l Replacement El Yes F El Repaired, El No El Replaced,

__ Replacement 1l Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced andle

8. Tests Conducted:Hydrostatic LI Pneumatic El Nom. Operating Press. LI Other LI Exempti-Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure _psig Test Temp. O__

F

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xl.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass JrQA Tech Specialist Date Owner ot'Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspected the components described in this Owner's Report during the period Vht/eL to z2* 9'/ and state that to the best of my knowledge and belief, the Owner hAs 6erformed ex mintons and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for Aanyinsection.*e.,.-.

personal injury or property damage or a loss of any kind arising from or connected with this

,...-rome F Swan Commissions NC1 524, N-I Inspector'S e National Board, State, Province and Endorsements 6

Date ._

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date 04/20/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: ZI1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 01741917 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NV Chemical and Volume Control 4.(b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair /Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 01 Repaired, [INo 1-MCR-NV-1025 Duke Energy N/A N/A Hanger N/A 0 Replaced,

__Replacement 0 Yes B 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced item 5 and 6 on 1-MCR-NV-1025

8. Tests Conducted:Hydrostatic 0I Pneumatic LI Nom. Operating Press. El Other El Exempt[@I Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A 4

Signedc-a6 ti .. F.R. Sorrow,QA Tech Support Date 04/20, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSQ. Thave inspe~ted/the components described in this Owner's Report during the period e& 7- to 1  ; and state that to the best of my knowledge and belief, the Owner h {s p'erfdrmed ei-*miratibns and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju r property damage or a loss of any kind arising from or connected with this f}inspection. .*

ome F Swan Commissions NC1524, N-I II snpatoee f ,e .National Board, State, Province and Endorsements Date* 3 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 3, 2007 526 S.'Church Street, Charlotte, NC 2820 1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1742718 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: VI - Instrument Air 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, El No 1-VI-124 Kerotest CK8-25 7903 N/A 1975 El Replaced, E1 Replacement [] Yes B 0l Repaired, El No El Replaced,

__ Replacement El Yes C El Repaired, El No El Replaced,

_ Replacement El Yes D El Repaired, El No El Replaced,

_E Replacement El Yes E E Repaired, El No El Replaced,

_E Replacement El Yes F E Repaired, El No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced disc.

8. Tests Conducted:Hydrostatic EJ Pneumatic 0 Nom. Operating Press. l] Other El Exemptl Pressure *100 psig Test Temp. *78 OF Pressure psig , Test Temp. OF Pressure psig Test Temp. OF

9. Remarks *Control room instrumentation information.

(Applicable Manufacturer's Data Reports to be attached)

• CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed * ,V FL Grass JrQA Tech Specialist Date , ' Z_____

Owner-OFOwner's Designee, Title.

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT ave inspecedthe components described in this Owner's Report during the period to 0 and state that to the best of my knowledge and belief, the Owner has perormed exarmiations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

4 YzC.-ý.Jerome F Swan Commissions NC1524, N-1.

Inspectrs rture National Board, State, Province and Endorsements

(

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke ,PowerCompany 1a. Date 04/26/2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Hagers Ferry Road, Huntersville, NC 28078 2a. Unit: l9l1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 01744670 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NI Safety Injection 4.(b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, E] No 1NI-0159 Kerotest LA4-10 8699 Valve 1976 0 Replaced, 19 Replacement ElYes B 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page I of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Performed Seal Weld on Bonnet to Body

8. Tests Conducted:Hydrostatic [] Pneumatic LI Nom. Operating Press. El Other El Exempt[]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks

.(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed;"(a&J F.R. Sorrow,QA Tech Support Date 04/26, 2007

'Owner or Owner's Designee, Title I CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H T have 1 tedthe components described in this Owner's Report during the period VAL7 to R361 .7;and state that to the best of my knowledge and belief, the Owner Ifas performed ekaminations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for A any personal injury r property damage or a loss of any kind arising from or connected with this Iinspection-. /

.t ro/m-.Jerome F Swan Commissions NC1524, N-I Ilnspector's Sia.re National Board, State, Province and Endorsements

(

/Datei//tJ.//

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 15, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: MclGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 21 012 r03 EShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1744836 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: BB - Steam Generator Blowdown Recycle 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME Ill 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A E0 Repaired, 2 No 1-MCR-BB-665 Duke Power 21786 N/A N/A N/A El Replaced,

]0 Replacement El Yes B El Repaired, 0 No 1-MCR-BB-665 Duke Power 21795 N/A N/A N/A El Replaced, 21 Replacement El Yes C El Repaired, El No El Replaced,

_E Replacement El Yes D El Repaired, El No El Replaced, El Replacement El Yes E E Repaired, El No El Replaced,

_E Replacement El Yes F E Repaired, El No El Replaced, 0E Replacement El Yes Page I of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced snubber.

8. Tests Conducted:Hydrostatic 0I Pneumatic LI Nom. Operating Press. LI Other LI Exempt[Z Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed,. A, o/aj FL Grass Jr,QA Tech Specialist Date Owner o['wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by H have inspqcted the components described in this Owner's Report during the period 2 to ,//.11"L; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

, -. c'rome F Swan Commissions NC1524, N-I IDenSpect's_ ,ure National Board, State, Province and Endorsements Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 1,2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 []Shared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1746129 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: MD100802

4. (a) Identification of System: BB - Steam Generator Blowdown Recycle 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0 Repaired, L] No 1-MCR-BB-501 Duke Power N/A N/A N/A N/A 0 Replaced,

__ Replacement 0 Yes B E Repaired, El No El Replaced,

]0 Replacement 0 Yes C 0 Repaired, El No 0 Replaced,

]0 Replacement 0 Yes D El Repaired, El No 0l Replaced,

]0 Replacement El Yes E 0 Repaired, 0 No El Replaced,

_ _Replacement El Yes F E Repaired, El No El Replaced,

__ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Modified hanaer per MD100802

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El Exemptil Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -411&11 FL Grass Jr,QA Tech Specialist Date 4 Owner qp'-wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by iJj have ins ted the components described in this Owner's Report during the period

%,/:;/o 17 to 1 7; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injL/y or property damage or a loss of any kind arising from or connected with this in s p e t io n . . -

eme F Swan Commissions NC1524, N-I "Inspector'si ture National Board, State, Province and Endorsements

( /Date 1t/*7--9 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date 04/20/2007 526 S. Church Street. Charlotte. NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 0IShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order # : 01746264 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job a Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NV Chemical and Volume Control 4.(b) Class of System: A

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair/ Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, 9No 1-MCR-NV-1235 Duke Energy 12393 N/A Hanger N/A [gReplaced,

_E Replacement El Yes B El Repaired, ZNo 1 -MCR-NV-1 235 Duke Energy 21756 N/A Hanger N/A 0 Replaced, I _Replacement El Yes C El Repaired, El No El Replaced, El Replacement El Yes D El Repaired, El No El Replaced,

_ Replacement El Yes E El Repaired, El No El Replaced,

_ Replacement El Yes F El Repaired, El No El Replaced,

_E Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced Snubber

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other El ExemptZ]

Pressure psig Test Temp. OF Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code, Section Xi.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed .4 L-- , F.R. Sorrow,QA Tech Support Date 04/20, 2007 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by CT have insp ted)he components described in this Owner's Report during the period

/ to 5,/-.L2 ,,/7; and state that to the best of my knowledge and belief, the Owner hsrformed examinrations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury r property damage or a loss of any kind arising from or connected with this

/inspection:./.

S-,-.-Jerome F Swan Commissions NC1 524, N-I I/ Inspector's Sigra/ National Board, State, Province and Endorsements K SDate .** _*__*

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date April 24, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 03 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1746595 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: CA - Auxiliary Feedwater 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Sertal No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A 0l Repaired, 2] No 1-MCR-CA-389 Duke Power 14824 N/A N/A N/A l] Replaced,

[0 Replacement 0 Yes B 0 Repaired, 12 No 1-MCR-CA-389 Duke Power 20539 N/A N/A N/A 0 Replaced, RI Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes D 0 Repaired, 0 No 0 Replaced,

]0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0l Repaired, 0 No 0 Replaced,

[0 Replacement 0- Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of.sheets is recorded at the top of this form.

7. Description of Work Replaced snubber

8. Tests Conducted:Hydrostatic [] Pneumatic L] Nom. Operating Press. El Other [] Exempti]

Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF Pressure .psig Test Temp. OF

9. Remarks (Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed -,** FL Grass JrQA Tech Specialist Date .

. Owner eofOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HHSA C-Thave inspepted he components described in this Owner's Report during the period qL4 / 7r to -/ 0O "7,and state that to the best of my knowledge and belief, the Owner hds pehformed examindtions and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for

• • nY pection.

personal injury

." or roperty damage or a loss of any kind arising from or connected with this

,, - '-4-dzome F Swan Commissions NC1524, N-I nspectors Si eNational

. Board, State, Province and Endorsements 6 Date *. *, 7 Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 3, 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haaers Ferry Road. Huntersville. NC 28078 2a. Unit: 01 02 03 EShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1746782 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM 9: ME101211

4. (a) Identification of System: NS - Containment Spray 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, 0l No 1-NS-25 Aloyco A0394 11 N/A 1973 0 Replaced, El Replacement RI Yes B El Repaired, El No 1-NS-25 BNL A05088-19-2 N/A N/A 2005 El Replaced, 01 Replacement R0 Yes C 0l Repaired, 0l No NS Piping Duke Power N/A 40 N/A 1981 El Replaced, IR] Replacement 0 Yes D El Repaired, El No O Replaced, 0_ Replacement El Yes E 0l Repaired, El No El Replaced,

__ Replacement El Yes F E Repaired, El No El Replaced, 0_ Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced valve and piping per ME101211.

8. Tests Conducted:Hydrostatic EJ Pneumatic E Nom. Operating Press. [] Other E Exemptol Pressure 200 psig Test Temp. 80 OF Pressure _psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks Test performed per MP/O/A/7650/076.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date 5 ,..-2c"7_

Owner or/Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspecteo the components described in this Owner's Report during the period

.T-_-_o o*/3/o  ; and state that to the best of my knowledge and belief, the Owner has pertormed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.,- /

erome F Swan Commissions NC1524, N-I Inspcto _. ,t ur_._ National Board, State, Province and Endorsements Daltpe Is 2_ _X(,7 1

Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company la. Date May 7. 2007 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: El1 02 E13 OShared (specify Units

3. Work Performed By: Duke Power Company 3a. Work Order #: 1749672 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: Lower Personnel Air Lock 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section Xl Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A El Repaired, El No 1-IAE-CV-5370 Anderson - N22643 1859 2" Check Valve 1986 0 Replaced, Greenwood 0E Replacement 01 Yes B El Repaired, 0l No 1-IAE-CV-5370 Anderson - N950129 2496 2" Check Valve. 1996 El Replaced, Greenwood _0 Replacement 01 Yes C El Repaired, El No El Replaced, 1 _ Replacement El Yes D El Repaired, El No 0 Replaced,

-__E Replacement El Yes E El Repaired, El No El Replaced,

__ Replacement El Yes F E Repaired, El No El Replaced,

[0 Replacement El Yes Page 1 of 2

Form NIS-2 (Back)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced valve

8. Tests Conducted:Hydrostatic El Pneumatic El Nom. Operating Press. El Other 0 Exempt[l Pressure *8 psig Test Temp.

• F Pressure psig Test Temp. OF Pressure psig Test Temp. OF

9. Remarks * - Test performed per PT/O/A4200/001 due to Operations Leak Rate Test. (zero detectable leakace).

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/.iA Certificate of Authorization No. N/A Expiration Date N/A Signed FL Grass Jr,QA Tech Specialist Date 4 *2 owner o&4wner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by h

Thave inspa e ep the components described in this Owner's Report during the period to-t .' _7; and state that to the best of my knowledge and belief, the Owner as performed edamtnations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal inju or property damage or a loss of any kind arising from or connected with this linspection. /

S -'---- Jerome F Swan Commissions NC1524, N-I Inspector's,tl pture National Board, State, Province and Endorsements 7'

I Page 2 of 2

FORM NIS-2 OWNER'S REPORT FOR REPAIR / REPLACEMENT ACTIVITY As Required By The Provisions Of The ASME Code Section XI

1. Owner Address: Duke Power Company 1a. Date February 28, 2006 526 S. Church Street, Charlotte, NC 28201-1006 Sheet 1 of 1

2. Plant Address: McGuire Nuclear Station 12700 Haqers Ferry Road, Huntersville, NC 28078 2a. Unit: 01 02 03 E]Shared (specify Units One & Two

3. Work Performed By: Duke Power Company 3a. Work Order #: 98672034/06 Address: 526 S. Church Street, Charlotte NC 28201-1006 Repair Organization Job #

Type Code Symbol Stamp: N/A Authorization No. N/A Expiration Date: N/A 3b. NSM or MM #: N/A

4. (a) Identification of System: NM - Nuclear Sampling 4. (b) Class of System: B

5. (a) Applicable Construction Code: ASME III 1971 Edition, Summer and Winter Addenda, N/A Code Cases (b) Applicable Edition of Section XI Utilized for Repair / Replacement Activity: 1998, 2000 Addenda (1998 through 2000 Addenda for Class MC and CC and their supports)

6. Identification of Components:

Column 1 Column 2 Column 3 Column 4 Column 5 Col 6 Column 7 Column 8 Name of Component Name of Mfg Mfg Serial No. National Board No. Other Identification Year Built Corrected, Removed, or ASME Code Stamped Installed (yes or no)

A R1 Repaired, 01 No 1NM-92 Dresser TK-61806 1966 N/A 1995 0 Replaced, 1 0 Replacement l] Yes B 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes C 0 Repaired, 0 No 0 Replaced, 1:1 Replacement [0 Yes D 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes E 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes F 0 Repaired, 0 No 0 Replaced,

[0 Replacement 0 Yes Page 1 of 2

rurin 1'410-e kDd(;K)

NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2 in. x 11 in. (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replaced disc and bonnet nuts

8. Tests Conducted:Hydrostatic E Pneumatic [] Nom. Operating Press. LI Other l] ExemptD Pressure psig Test Temp. OF Pressure _psig Test Temp. OF Pressure _psig Test Temp. OF

9. Remarks Verified leak test per procedure SM/O/A/8030/O01 Note: this valve will be placed into stock upon receipt inspection.

(Applicable Manufacturer's Data Reports to be attached)

CERTIFICATE OF COMPLIANCE I certify that the statements made in the report are correct and this conforms to the requirements of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Certificate of Authorization No. N/A Expiration Date N/A Signed. FL Grass Jr,QA Tech Specialist Date Owner oirOwner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of North Carolina and employed by HSB CT have inspctehe components described in this Owner's Report during the period 1149(0o to 2; and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of ASME Code,Section XI.

By signing this certificate neither the Inspector-nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injurypr property damage or a loss of any kind arising from or connected with this inspection.

a.,rt- /..-ý,* 0rome F Swan Commissions NC1524, N-I Inspector's Si ature National Board, State, Province and Endorsements Date 7/7 Page 2 of 2

6.0 PressureTestinq All system pressure test requirements have been satisfied for the First Inspection Period.

Some pressure tests were completed after EOC 17 but prior to December 1, 2005, the date ending the First Period. Those pressure tests credited for the First Period which were not listed in the summary report for EOC 17 are shown in this summary report. See Table 6-1 for the specific pressure test zone listing of those tests Table 6-1 Detailed Class 2 - 1s' PeriodZones Not Listed in EOC17 Report VT-2 Examination Zone Number Boundary Dwg Completion Status Date 1BB-096L-B MC-ISIL-1 580-01.00 1 st Period Complete 11/03/05 1CA-032L-B MC-ISIL-1584-01.00 1st Period Complete 11/22/05 MC-ISIL-1591-01.01 1St Period Complete 11/22/05 MC-ISIL- 1592-01.00 1st Period Complete 11/22/05 MC-ISIL-1617-01.00 1 st Period Complete 11/22/05 1FW-027L-B MC-ISIL-1554-03.00 1St Period Complete 10/26/05 MC-ISIL- 1554-03.01 1 st Period Complete 10/26/05 MC-ISIL-1561-01.00 ist Period Complete 10/26/05 MC-ISIL-1562-03.00 1s' Period Complete 10/26/05 MC-ISIL-1563-01.00 1s' Period Complete 10/26/05 MC-ISIL-1 571-01.00 1st Period Complete 10/26/05 1 NI-060L-B MC-ISIL-1562-02.01 1st Period Complete 11/21/05 MC-ISIL-1562-03.00 1st Period Complete 11/21/05 1NV-016L-B MC-ISIL-1554-01.00 1 st Period Complete 11/10/05 MC-ISIL-1 554-01.01 1 st Period Complete 11/10/05 MC-ISIL-1554-01.02 1 St Period Complete 11/10/05 MC-ISIL-1554-02.00 1st Period Complete 11/10/05 MC-ISIL-1554-02.01 1st Period Complete 11/10/05 MC-ISIL-1554-03.00 is' Period Complete 11/10/05 MC-ISIL-1554-03.01 1 st Period Complete 11/10/05 MC-ISIL-1554-05.00 1st Period Complete 11/10/05 MC-ISIL-1561-01.00 1st Period Complete 11/10/05 MC-ISIL-1562-01.00 1st Period Complete 11/10/05 MC-ISIL-1562-03.00 1s' Period Complete 11/10/05 Outage 4/EOC 18 Page 1 of 8 McGuire Unit 1 Revision 0 Section 6 - Third Ten-Year Interval July 2, 2007

VT-2 Examination Zone Number Boundary Dwg Completion Status Date 1NV-017L-B MC-ISIL-1554-01.00 1st Period Complete 11/03/05 MC-ISIL-1554-01.01 1 st Period Complete 11/03/05 MC-ISIL-1554-01.02 Ist Period Complete 11/03/05 1NV-018L-B MC-ISIL-1554-01.02 1 st Period Complete 11/29/05 1NV-051 L-B MC-ISIL-1554-03.01 1S t Period Complete 11/14/05 1SM-036L-B MC-ISIL-1593-01.00 1st Period Complete 11/03/05 MC-ISlL-1593-01.03 1st Period Complete 11/03/05 1SM-037L-B MC-ISIL-1593-01.00 Is Period Complete 11/03/05 MC-ISIL-1593-01.03 1" Period Complete 11/03/05 Table 6-2 shows the number of Class 1 (Category B-P), Class 2 (Category C-H), and Risk Informed Segment (Category R-A) pressure tests zones completed from refueling outage EOC-17 through refueling outage EOC-18 associated with the Second Inspection Period. There was one zone that contained through-wall leakage. See Table 6-5 for the specific listing.

Table 6-2 Outage Specific Summary Examination Category Test Requirement Total Completed EOC18 B-P System Leakage Test (IWB-5220) 1 C-H System Leakage Test (IWC-5220) 0 R-A-_,- ,.....T-..f,.W6 ER,*sk Informedy g R-A Risk Informed VT-2 for Socket Welds 67 Segments Outage 4/EOC 18 Page 2 of 8 McGuire Unit 1 Revision 0 Section 6 - Third Ten-Year Interval July 2, 2007

Table 6-3 shows a completion status of pressure tests zones conducted during the Second Period of the Third Ten-Year Interval.

Table 6-3 6.

Period Snecifk Summary Total Total (%)

Examination Test Examinations Examinations Examinations Category Requirement Required For Credited For Complete For This Period This Period This Period B-P System Leakage 2 1 50%

Test (IWB-5220)

C-H System Leakage 30 0 0%

Test (IWC-5220)

R-A System Leakage (67 Segments 67 50%

Test Each Refueling Outage) 134 For Period The Class 1 (Category B-P) pressure test zone is required each refueling outage.

Table 6-4 shows a completion status of the Class 1 (Category B-P) pressure test zone conducted during refueling cycle EOC 18.

Table 6-4 Detailed Class 1 Listing EOC 18 Zone Completion Number Boundary Dwg Status EOC 18 VT-2 Examination Date 1NC-070L-A MC-ISIL- 1553-01.00 Complete 05/08/07 MC-ISIL-1553-02.00 Complete 05/08/07 MC-1I1L-1553-02.01 Complete 05/08/07 MC-ISIL- 1554-01.00 Complete 05/08/07 MC-ISIL-1554-01.01 Complete 05/08/07 MC-ISIL- 1554-01.02 Complete 05/08/07 MC-ISIL-1 561 -01.00 Complete 05/08/07 MC-ISIL-1562-01.00 Complete 05/08/07 MC-ISIL- 1562-02.00 Complete 05/08/07 MC-ISIL-1562-02.01 Complete 05/08/07 MC-ISIL- 1562-03.00 Complete 05/08/07 MC-ISIL-1 562-03.01 Complete 05/08/07 Outage 4/EOC 18 Page 3 of 8 McGuire Unit 1 Revision 0 Section 6 - Third Ten-Year Interval July 2, 2007

Class 2 (Category C-H) pressure test zones are required once each Inspection Period.

Table 6-5 shows a completion status of Class 2 (Category C-H) pressure tests required for the Second Period of the Third Ten-Year Interval.

Table 6-5 Detailed Class 2 - 2nc Period Listing VT-2 Examination Zone Number Boundary Dwg Completion Status Date 1 1BB-096L-B MC-ISIL-1580-01.00 Partial 05/08/07 2 1BB-098L-B MC-ISIL-1572-03.00 Not Yet Tested N/A MC-ISIL-1580-01.00 Not Yet Tested N/A MC-ISIL-1 584-01.00 Not Yet Tested N/A 3 1CA-006L-B MC-ISIL-1592-01.00 Not Yet Tested N/A 4 1CA-032L-B MC-ISIL-1584-01.00 Not Yet Tested N/A MC-ISIL-1 591-01.01 Not Yet Tested N/A MC-ISIL-1592-01.00 Not Yet Tested N/A MC-ISIL-1 617-01.00 Not Yet Tested N/A 5 1FW-027L-B MC-ISIL-1554-03.00 Not Yet Tested N/A MC-ISIL-1554-03.01 Not Yet Tested N/A MC-ISIL-1561-01.00 Not Yet Tested N/A MC-ISIL-1562-03.00 Not Yet Tested N/A MC-ISIL-1563-01.00 Not Yet Tested N/A MC-ISIL-1 571-01.00 Not Yet Tested N/A 6 1ND-019L-B MC-ISIL-1554-01.02 Not Yet Tested N/A MGC-ISIL-i 561-01.00 Partial 03/10/07 MC-ISIL- 1562-03.00 Partial 03/13/07 MG-ISIL-1 562-03.01 Partial 03/10/07 MC-ISIL-1563-01.00 Not Yet Tested N/A MC-ISIL-1571-01.00 Not Yet Tested N/A MC-ISIL-1572-01.00 Not Yet Tested N/A 7 1ND-050L-B MC-ISIL-1561 -01.00 Not Yet Tested N/A MC-ISIL-1562-03.01 Not Yet Tested N/A MC-ISIL-1 563-01.00 Not Yet Tested N/A Outage 4/EOC 18 Page 4 of 8 McGuire Unit I Revision 0 Section 6 - Third Ten-Year Interval July 2, 2007

VT-2 Examination Zone Number Boundary Dwg Completion Status Date 8 1NI-021 L-B MC-ISIL-1 562-02.00 Not Yet Tested N/A MC-ISIL-1 562-02.01 Not Yet Tested N/A MC-ISIL-1 572-01.01 Not Yet Tested N/A 9 1NI-022L-B MC-ISIL-1562-03.00 Not Yet Tested N/A MC-ISIL-1 562-03.01 Not Yet Tested N/A 10 1NI-039L-B MC-ISIL-1562-03.01 Not Yet Tested N/A 11 1NI-053L-B MC-ISIL-1 562-03.00 Not Yet Tested N/A 12 1NI-060L-B MC-ISIL-1562-02.01 Partial 04/18/07 MC-ISIL-1562-03.00 Partial 04/18/07 13 1NI-071 L-B MC-ISIL-1562-01.00 Not Yet Tested N/A 14 1NI-074L-B MC-ISIL-1562-03.00 Not Yet Tested N/A 15 1NM-046L-B MC-ISIL-1572-01.01 Not Yet Tested N/A 16 1NS-023L-B MC-ISIL-1563-01.00 Not Yet Tested N/A 17 1NS-024L-B MC-ISIL-1563-01.00 Not Yet Tested N/A 18 1NV-016L-B MC-ISIL-i 554-01.00 Partial 05/27/07 MC-ISIL-1554-01.01 Partial 05/27/07 MC-ISIL-1554-01.02 Not Yet Tested N/A MC-ISIL-1554-02.00 Not Yet Tested N/A MC-ISIL-1554-02.01 Not Yet Tested N/A MC-ISIL-1554-03.00 Partial 05/27/07 MC-ISIL-1554-03.01 Partial 05/27/07 MC-ISIL-1554-05.00 Not Yet Tested N/A MC-ISIL-1561-01.00 Not Yet Tested N/A MC-ISIL-1562-01.00 Partial 05/27/07 MC-ISIL-1562-03.00 Partial 05/27/07 19 1NV-017L-B MC-ISIL-1554-01.00 Partial 05/08/07 MC-ISIL-1554-01.01 Partial 05/08/07 MC-ISIL-1554-01.02 Partial 05/08/07 MC-ISIL-1554-01.03 Partial 05/08/07 Outage 4/EOC 18 Page 5 of 8 McGuire Unit 1 Revision 0 Section 6 - Third Ten-Year Interval July 2, 2007

VT-2 Examination Zone Number Boundary Dwg Completion Status Date 20 1NV-018L-B MC-ISIL-1554-01.02 Partial 05/08/07 21 1NV-020L-B MC-ISIL-1554-01.02 Not Yet Tested N/A 22 1NV-045L-B MC-ISIL-1554-03.00 Partial 05/27/07 23 1 NV-051L-B MC-ISIL-1554-03.01 Partial 05/27/07 24 1RN-004L-B MC-ISIL-1574-04.00 Partial 05/02/07 25 1 RV-002L-B MG-ISIL-1604-03.00 Partial 03/15/07 26 1SA-035L-B MC-ISIL-1593-01.02 Not Yet Tested N/A 27 1SM-006L-B MC-ISIL-1572-03.00 Partial 05/08/07 MC-ISIL-1591-01.011 Partial 05/08/07 MC-ISIL-1593-01.00 Complete 05/08/07 MC-ISIL-1593-01.03 Complete 05/08/07 28 1SM-036L-B MC-ISIL-1593-01.00 Not Yet Tested N/A MC-ISIL-1593-01.02 Not Yet Tested N/A MC-ISIL-1593-01.03 Not Yet Tested N/A 29 1SM-037L-B MC-ISIL-1593-01.00 Not Yet Tested N/A MC-ISIL-1593-01.03 Not Yet Tested N/A 30 1YA-043L-B MC-ISIL-1617-01.00 Not Yet Tested N/A Risk Informed Segments (Category R-A) that receive a pressure test are required each refueling outage. Table 6-6 shows a completion status of the Risk Informed Segment pressure test zones conducted during refueling cycle EOC 18.

Table 6-6 Detailed Risk Informed Pressure Test Listing EOC 18 Zone Segment Completion EOC 18 VT-2 Number Boundary Dwg Number Status Examination Date 1 1NC-070L-A MC-ISIL-1553-01.00 NC-18 Complete 05/08/07 2 NC-19 Complete 05/08/07 3 NC-20 Complete 05/08/07 4 NC-21 Complete 05/08/07 5 NC-23 Complete 05/08/07 6 NC-86 2 Complete 05/08/07 7 NC-89 Complete 05/08/07 8 NC-90 Complete 05/08/07 1 Relevant condition leakage observed. Reference PIP#M07-2973 2 Part of this segment is also shown on drawing MC-ISIL-1554-03.01 Outage 4/EOC 18 Page 6 of 8 McGuire Unit 1 Revision 0 Section 6 - Third Ten-Year Interval July 2, 2007

EOC 18 Zone Segment Completion EOC 18 VT-2 Number Boundary Dwg Number Status Examination Date 9 1 NC-070L-A MC-ISIL-1553-02.00 NC-054 Complete 05/08/07 10 NC-055 Complete 05/08/07 11 NC-056 Complete 05/08/07 12 MC-ISIL- 1554-01.00 NV-033A Complete 05/08/07 13 NV-033B Complete 05/08/07 14 NV-034A Complete 05/08/07 15 NV-034B Complete 05/08/07 16 NV-037 Complete 05/08/07 17 NV-038 Complete 05/08/07 18 NV-041 A Complete 05/08/07 19 NV-041 B Complete 05/08/07 20 NV-042A Complete 05/08/07 21 NV-042B Complete 05/08/07 22 MC-ISIL- 1554-01.01 NV-030A Complete 05/08/07 23 NV-030B Complete 05/08/07 24 NV-032A Complete 05/08/07 25 NV-032B Complete 05/08/07 26 NV-035 Complete 05/08/07 27 NV-036 Complete 05/08/07 28 NV-039A Complete 05/08/07 29 NV-039B Complete 05/08/07 30 NV-040A Complete 05/08/07 31 NV-040B Complete 05/08/07 32 MC-ISIL-1562-01.00 NI-068 Complete 05/08/07 33 NI-069 Complete 05/08/07 34 NI-070 Complete 05/08/07 35 NI-071 Complete 05/08/07 36 1NV-016L-B I MC-ISIL-1554-01.00 NV-020H Complete 05/08/07 37 NV-020F I Complete 1 05/08/07 38 NV-020GA Complete 05/08/07 39 MC-ISIL-1554-01.01 NV-020AD Complete 05/08/07 40 NV-020B Complete 05/08/07 41 NV-020CA Complete 05/08/07 42 NV-020D Complete 05/08/07 43 NV-020EA Complete 05/08/07 44 MC-ISIL-1554-03.00 NV-019AA 3 Complete 05/08/07 45 NV-019B Complete 05/08/07 46 NV-019D Complete 05/08/07 47 NV-020AB Complete 05/08/07 48 NV-020AC Complete 05/08/07 59 NV-021A Complete 05/08/07 50 NV-021 B Comolete 05/08/07 3 Part of this segment is also shown on drawing MC-ISIL-1 554-03.01 Outage 4/EOC 18 Page 7 of 8 McGuire Unit 1 Revision 0 Section 6 - Third Ten-Year Interval July 2, 2007

EOC 18 Zone Segment Completion EOC 18 VT-2 Number Boundary Dwg Number Status Examination Date 51 1NV-016L-B MC-ISIL-1554-03.01 NV-002AB 4 Complete 05/08/07 52 NV-002D Complete 05/08/07 53 NV-019C Complete 05/08/07 54 NV-019E Complete 05/08/07 55 1NV-017L-B MC-ISIL-1554-01.00 NV-028 5 Complete 05/08/07 56 NV-029 5 Complete 05/08/07 57 MC-ISIL-1554-01.01 NV-026 5 Complete 05/08/07 58 NV-027 5 Complete 05/08/07 59 1NV-018L-B MC-ISIL-1554-01.02 NV-080A Complete 05/08/07 60 NV-080B Complete 05/08/07 61 NV-084A Complete 05/08/07 62 1 NV-01 8L-B MC-ISIL-1 554-01.02 NV-084B Complete 05/08/07 63 NV-084C Complete 05/08/07 64 1 NV-045L-B MC-ISIL-1554-03.00 NV-002C Complete 05/08/07 65 NV-108A Complete 05/08/07 66 NV-1 09 Complete 05/08/07 67 1NV-051L-B MC-ISIL-1554-03.01 NV-011A 6 Complete 05/08/07 Section 6 Prepared By: Date:

Q~7Z 7 (I 9 4 Part of this segment is also shown on drawing MC-ISIL-1562-03.00 5 Part of this segment is also shown on drawing MC-ISIL-1554-01.03 6 Part of this segment is also shown on drawings MC-ISIL-1554-03.01 and MC-ISIL-1562-01.00 Outage 4/EOC 18 Page 8 of 8 McGuire Unit 1 Revision 0 Section 6 - Third Ten-Year Interval July 2, 2007