ML14098A421

McGuire, Units 1 and 2 - Seismic Hazard and Screening Report (CEUS Sites), Response to NRC 10 CFR 50.54(f) Request for Information Pursuant to Title 10 of the Code of Federal Regulations 50.54(f) Regarding Recommendations 2.1, 2.3 and 9.3 o

ML14098A421
Person / Time
Site:	McGuire, Mcguire
Issue date:	03/20/2014
From:	Capps S D Duke Energy Carolinas
To:	Document Control Desk, Office of Nuclear Reactor Regulation
References
MNS-14-029
Download: ML14098A421 (38)

Text

Steven D. Capps Vice President DUKE McGuire Nuclear Station V ENERGY, Duke Energy MG01VP 112700 Hagers Ferry Road Huntersville, NC 27078 o: 980.875.4805 f: 980.875.4809 Steven.Capps@duke-energy.com 10 CFR 50.54(f)March 20, 2014 Serial: MNS-14-029 ATTN: Document Control Desk U.S. Nuclear Regulatory Commission Washington, DC 20555 Duke Energy Carolinas, LLC (Duke Energy McGuire Nuclear Station (MNS), Units 1 and 2 Docket Nos. 50-369 and 50-370 Renewed License Nos. NPF-9 and NPF-17

Subject:

Seismic Hazard and Screening Report (CEUS Sites), Response to NRC 10 CFR 50.54(f) Request for Information Pursuant to Title 10 of the Code of Federal Regulations 50.54(f) regarding Recommendations 2.1, 2.3 and 9.3 of the Near-Term Task Force Review of Insights from the Fukushima Dai-ichi Accident

References:

1. NRC Letter, Request for Information Pursuant to Title 10 of the Code of Federal Regulations 50.54(f) Regarding Recommendations 2.1, 2.3, and 9.3, of the Near-Term Task Force Review of Insights from the Fukushima Dai-ichi Accident, dated March 12, 2012, ADAMS Accession No. ML12053A340

2. EPRI Report 1025287, Seismic Evaluation Guidance, Screening, Prioritization and Implementation Details (SPID) for the Resolution of Fukushima Near-Term Task Force Recommendation 2.1: Seismic, ADAMS Accession No. ML1 2333A1 70 3. NRC Letter, Endorsement of EPRI Final Draft Report 1025287, Seismic Evaluation Guidance, dated February 15, 2013, ADAMS Accession No. ML12319A074

4. NEI Letter, Proposed Path Forward for NTTF Recommendation 2.1: Seismic Reevaluations, dated April 9, 2013, ADAMS Accession No. ML13101A379

5. NRC Letter, Electric Power Research Institute Final Draft Report XXXXXX, Seismic Evaluation Guidance:

Augmented Approach for the Resolution of Near-Term Task Force Recommendation 2.1: Seismic, as an Acceptable Alternative to the March 12, 2012, Information Request for Seismic Reevaluations, dated May 7, 2013, ADAMS Accession No. ML 13106A331 United States Nuclear Regulatory Commission March 20, 2014 Page 2 Ladies and Gentlemen:

On March 12, 2012, the Nuclear Regulatory Commission (NRC) issued Reference 1 to all power reactor licensees and holders of construction permits in active or deferred status. Enclosure 1 of Reference 1 requested each addressee located in the Central and Eastern United States (CEUS) to submit a Seismic Hazard Evaluation and Screening Report within 1.5 years from the date of Reference 1.The Nuclear Energy Institute (NEI) submitted Reference 4 requesting NRC agreement to delay submittal of the CEUS Seismic Hazard Evaluation and Screening Report so that an update to the Electric Power Research Institute (EPRI) ground motion attenuation model could be completed and used to develop that information.

NEI proposed that descriptions of subsurface materials and properties and base case velocity profiles be submitted to the NRC by September 12, 2013, with the remaining seismic hazard and screening information submitted by March 31, 2014.Industry guidance and detailed information to be included in the Seismic Hazard Evaluation and Screening Report submittals is provided by Reference

2. The industry guidance was endorsed by the NRC in a letter dated February 15, 2013 (Reference 3).The attached report provides the Seismic Hazard Evaluation and Screening Report for MNS as directed by Section 4 of Reference 2 and in accordance with the schedule provided in Reference 4.There are no regulatory commitments associated with this letter.Should you have any questions regarding this submittal, please contact George Murphy at 980-875-5715.

I declare under penalty of perjury that the foregoing is true and correct. Executed on March 20, 2014.Sincerely, Steven D. Capps

Enclosure:

MNS Seismic Hazard Evaluation and Screening Report United States Nuclear Regulatory Commission March 20, 2014 Page 3 xc: V.M. McCree, Region II Administrator U.S. Nuclear Regulatory Commission Marquis One Tower 245 Peachtree Center Avenue NE, Suite 1200 Atlanta, Georgia 30303-1257 John Boska, Project Manager (ONS)U.S. Nuclear Regulatory Commission One White Flint North, Mailstop O-8G9A 11555 Rockville Pike Rockville, MD 20852-2738 G. E. Miller, Project Manager (CNS & MNS)U.S. Nuclear Regulatory Commission 11555 Rockville Pike Mail Stop 8 G9A Rockville, MD 20852-2738 J. Zeiler NRC Senior Resident Inspector McGuire Nuclear Station Justin Folkwein American Nuclear Insurers 95 Glastonbury Blvd., Suite 300 Glastonbury, CT 06033-4453 Enclosure MNS Seismic Hazard Evaluation and Screening Report NO. DUKCORP042-PR-002 U-J EN ER CON PROJECT REPORT REV. 0... .,(ee,1 v~ COVER SHEET Page 1 of 34 SEISMIC HAZARD AND SCREENING REPORT IN RESPONSE TO THE 50.54(f) INFORMATION REQUEST REGARDING FUKUSHIMA NEAR-TERM TASK FORCE RECOMMENDATION 2.1: SEISMIC for MCGUIRE NUCLEAR STATION DUKE ENERGY CAROLINAS Prepared by: Date: Shana Gibbs Reviewed by: Approved by: Mitchell Mrvt~ay Benjamin Kosbab Date: Date: 31[-

NO. DUKCORP042-PR-002 M ENERCON PROJECT REPORT Fj EceeEe eREVISION STATUS SHEET REV. 0 Excellen~ce--Every project. Every doy Page 2 of 34 PROJECT REPORT REVISION STATUS REVISION DATE DESCRIPTION 0 Initial issue.PAGE REVISION STATUS PAGE NO. REVISION PAGE NO. REVISION All 0 APPENDIX REVISION STATUS PAGE PAGE APPENDIX NO. NO. REVISION NO. APPENDIX NO. NO. REVISION NO.A All 0 1 Introduction Following the accident at the Fukushima Dai-ichi nuclear power plant resulting from the March 11, 2011, Great Tohoku Earthquake and subsequent tsunami, the Nuclear Regulatory Commission (NRC) established a Near-Term Task Force (NTTF) to conduct a systematic review of NRC processes and regulations and to determine if the agency should make additional improvements to its regulatory system. The NTTF developed a set of recommendations intended to clarify and strengthen the regulatory framework for protection against natural phenomena.

Subsequently, the NRC issued a 50.54(f) letter (Reference

1) that requests information to assure that these recommendations are addressed by all U.S. nuclear power plants. The 50.54(f) letter (Reference

1) requests that licensees and holders of construction permits under 10 CFR Part 50 (Reference 2)reevaluate the seismic hazards at their sites against present-day NRC requirements.

Depending on the comparison between the reevaluated seismic hazard and the current design basis, the result is either no further risk evaluation or the performance of a seismic risk assessment.

Risk assessment approaches acceptable to the staff include a seismic probabilistic risk assessment (SPRA), or a seismic margin assessment (SMA).Based upon the risk assessment results, the NRC staff will determine whether additional regulatory actions are necessary.

This report provides the information requested in items (1) through (7) of the "Requested Information" section in Attachment 1 of the 50.54(f) letter (Reference

1) pertaining to NTTF Recommendation 2.1: Seismic for the McGuire Nuclear Station (McGuire), located in Mecklenburg County, North Carolina.

In providing this information, Duke Energy Carolinas (Duke) followed the guidance provided in the Seismic Evaluation Guidance: Screening, Prioritization, and Implementation Details (SPID) for the Resolution of Fukushima Near-Term Task Force Recommendation 2.1: Seismic (Reference 3). The Augmented Approach, Seismic Evaluation Guidance:

Augmented Approach for the Resolution of Fukushima Near-Term Task Force Recommendation 2.1: Seismic (Reference 4), has been developed as the process for evaluating critical plant equipment as an interim action to demonstrate additional plant safety margin, prior to performing the complete plant seismic risk evaluations.

The original geologic and seismic siting investigations for McGuire meet General Design Criterion 2 in Appendix A to 10 CFR Part 50 (Reference 2). The Safe Shutdown Earthquake Ground Motion (SSE) was developed in accordance with General Design Criterion 2 in Appendix A to 10 CFR Part 50 (Reference

2) and used for the design of seismic Category I structures, systems, and components (SSC). (Reference 10, Section 3.1)In response to the 50.54(f) letter (Reference

1) and following the guidance provided in the SPID (Reference 3), a seismic hazard reevaluation was performed.

For screening purposes, a Ground Motion Response Spectrum (GMRS) was developed.

The GMRS development and supporting seismic hazard analysis (Sections 2.2, 2.3, and 2.4 of this report) for McGuire was performed by the Electric Power Research Institute (EPRI)(Reference 8). Based on the results of the screening evaluation, McGuire screens in for a risk evaluation and a spent fuel pool integrity evaluation.

McGuire Nuclear Station 3 Report Number: DUKCORP042-PR-002 2 Seismic Hazard Reevaluation McGuire is located in northwestern Mecklenburg County, North Carolina, 17 miles north-northwest of Charlotte, North Carolina (Reference 10, Section 2.1). It is bordered on the west by the Catawba River and on the north by Lake Norman which is formed by Cowans Ford Dam adjacent to the site. The site is located in the Charlotte Belt, one of five northeast trending rock belts within the Piedmont Geologic Province.

This belt consists of metamorphosed sedimentary and volcanic rocks with igneous rocks emplaced by several intrusive episodes during its early history. There is no evidence of movement along the regional faults since Triassic time or about 180 million years ago.Therefore, it is concluded that there are no identifiable active faults in the region of the site. From an engineering geology standpoint there are no local geologic features which adversely affect the station structures.

Where zones of irregular weathering of bedrock occurred, the weathered material was excavated and fill concrete was used under foundation structures, or piles were driven to suitable rock bearing for Category I structures. (Reference 10, Section 2.5)Historical records indicate that the maximum earthquake intensity experienced at the site was the Charleston earthquake of August 21, 1886 with an estimated site surface intensity between VI-VII Modified Mercalli Scale (MM). The maximum earthquake intensity which has occurred within the region is VII to VIII MM. The original investigation of historical seismic activity in the region estimated that the maximum expected earthquake intensity is between VII and VIII MM. The SSE for foundations on jointed rock and slightly weathered rock is 0.15g (Reference 10, Section 2.5). This value is very conservative, considering the observed surface intensities in the region and the overburden amplification (Reference 10, Former Appendix 2E, Section 4.2).2.1 REGIONAL AND LOCAL GEOLOGY The general site area lies near the center of a region known as the Piedmont Geologic Province.

The Piedmont Geologic Province is bordered on the east by the Coastal Plain Province and on the west by the Blue Ridge Province.

The Coastal Plain generally consists of poorly consolidated sediments which include gravels, sands, clays, limestones, and marls. The Blue Ridge is a belt of meta-sedimentary rocks of the amphibolite facies in which igneous rocks were emplaced.

Several Pre-Triassic faults or structural belts were associated faults described in published literature are located within 75 miles of the site. These structures probably occurred during or immediately following the Appalachian Orogeny at the close of the Paleozoic Era, and there is no evidence of their movement since Triassic time, or 180 million years ago. (Reference 10, Section 2.5)The station site is located 17 miles northwest of Charlotte, North Carolina.

It is bordered on the west by the Catawba River and on the north by Lake Norman which is formed by Cowans Ford Dam adjacent to the site. The site is underlain by metamorphosed sedimentary, volcanic, and intrusive igneous rocks ranging in age from Paleozoic Era to the Triassic Period. There have been no known evidences of unrelieved residual stresses, such as "rock squeeze", or "pop-ups", or "rockbursts" in the Piedmont Region.McGuire Nuclear Station 4 Report Number: DUKCORP042-PR-002 Furthermore, no evidence of such occurrences was seen in the construction excavations at the McGuire site. Therefore, if unrelieved stresses do exist in the bedrock, they are of no consequence to the stability of the station structures. (Reference 10, Section 2.5)2.2 PROBABILISTIC SEISMIC HAZARD ANALYSIS 2.2.1 Probabilistic Seismic Hazard Analysis Results In accordance with the 50.54(f) letter (Reference

1) and following the guidance in the SPID (Reference 3), a probabilistic seismic hazard analysis (PSHA) was completed using the recently developed Central and Eastern United States Seismic Source Characterization (CEUS-SSC) for Nuclear Facilities (Reference

5) together with the updated EPRI Ground-Motion Model (GMM) for the CEUS (Reference 6). For the PSHA, a lower-bound moment magnitude of 5.0 was used, as specified in the 50.54(f)letter (Reference 1).For the PSHA, the CEUS-SSC background seismic sources out to a distance of 400 miles (640 km) around McGuire were included.

This distance exceeds the 200 mile (320 kin) recommendation contained in NRC Reg. Guide 1.208 (Reference

7) and was chosen for completeness.

Background sources included in this site analysis are the following:

1. Atlantic Highly Extended Crust (AHEX)2. Extended Continental Crust-Atlantic Margin (ECCAM)3. Extended Continental Crust-Gulf Coast (ECCGC)4. Illinois Basin Extended Basement (IBEB)5. Mesozoic and younger extended prior -narrow (MESE-N)6. Mesozoic and younger extended prior -wide (MESE-W)7. Midcontinent-Craton alternative A (MIDCA)8. Midcontinent-Craton alternative B (MIDCB)9. Midcontinent-Craton alternative C (MIDCC)10. Midcontinent-Craton alternative D (MIDCD)11. Non-Mesozoic and younger extended prior -narrow (NMESE-N)12. Non-Mesozoic and younger extended prior -wide (NMESE-W)13. Paleozoic Extended Crust narrow (PEZN)14. Paleozoic Extended Crust wide (PEZW)15. Reelfoot Rift (RR)16. Reelfoot Rift including the Rough Creek Graben (RR-RCG)17. Study region (STUDYR)For sources of large magnitude earthquakes, designated as Repeated Large Magnitude Earthquake (RLME) sources in CEUS-SSC (Reference 5), the following sources lie within 621 miles (1,000 km) of the site and were included in the analysis: 1. Charleston

2. Commerce 3. Eastern Rift Margin Fault northern segment (ERM-N)4. Eastern Rift Margin Fault southern segment (ERM-S)5. Marianna 6. New Madrid Fault System (NMFS)7. Wabash Valley McGuire Nuclear Station 5 Report Number: DUKCORP042-PR-002 For each of the above background and RLME sources, the mid-continent version of the updated CEUS EPRI GMM (Reference

6) was used.2.2.2 Base Rock Seismic Hazard Curves Consistent with the SPID (Reference 3), base rock seismic hazard curves are not provided as the site amplification approach referred to as Method 3 from NUREG/CR-6728 (Reference

16) has been used. Seismic hazard curves are shown below in Section 2.3.7 at the SSE control point elevation (discussed below in Section 3.2).2.3 SITE RESPONSE EVALUATION Following the guidance contained in Seismic Enclosure 1 of the 50.54(f) letter (Reference

1) and in the SPID (Reference

3) for nuclear power plant sites that are not founded on hard rock (considered as having a shear-wave velocity of at least 9285 fps (2.83 km/sec), or 9200 fps as approximated in the SPID (Reference 3)), a site response analysis was performed for McGuire.2.3.1 Description of Subsurface Material McGuire is located in the Piedmont Physiographic Province of North Carolina.

The general site conditions consist of residual soils overlying partially weathered rock grading into hard metamorphic igneous rocks (Reference 9). As depth into partially weathered rock increases the degree of weathering decreases as sound rock, defined as rock quality designation (RQD) of 75% or greater, is encountered.

McGuire consists of two units (1 and 2) with both reactor buildings supported on sound rock. Table 2.3.1-1 shows the single suite of geotechnical properties appropriate for Units 1 and 2.McGuire Nuclear Station 6 Report Number: DUKCORP042-PR-002 Table 2.3.1-1 Summary of site geotechnical profile for McGuire (Reference 9)Depth SShear-wave Compressional eVelocity Wave Velocity Poisson's Range(f) Description (pcf) Veoct Wave ratio__ft._______(fps) fs 0-4 Stiff Sandy 105 800 1400 0.26 Micaceous Silt Stiff to Very Stiff 4-10 Sandy Micaceous 105 1220 1900 0.15 Silt Firm to Stiff 10-26 Micacto Silt 105 1300 2500 0.50 Micaceous Silt 26-31 Very Dense Fine 135 1600 2950 0.50 Sand Partially Weathered 31-41 Rock and Very Soft 150 3250 5500 0.23 Granite Very Soft to 41-50 Moderately Hard 172 4750 8900 0.30 Diorite RQD = 15%to 80%Hard Diorite RQD =50-56.5 80% 172 7200 13400 0.30 80%56.5-64(2)

See Note 2 172 7200 13400 0.30 64+ See Note 2 172 9200 17212 0.30 (1) Depth begins at Yard Grade Elevation 760 ft. This is the "Ground Surface Elevation".

(2) Note: Boring H-70 terminated at El. 703.4 ft. or 56.5 ft. below Yard Grade. Velocities beyond this depth are not confirmed by tests. Vs = 7,200 fps from 56.5 ft. -64 ft. is assumed from test at 54.5 ft. Vs = 9,200 fps beginning at 64 ft. below Yard Grade is extrapolated from Measurements at 45.5 ft. and 54.5 ft. below Yard Grade.(3) The control point elevation is taken to be 43.5 ft. below the Yard Grade Elevation.

The following description of the general geology at the site is taken directly from AMEC Data for Site Amplifications (Reference 9): "The four major rock types appearing at the site are dark green meta-gabbro, light gray fine to medium grained granite, black and white fine grained diorite, and black and white coarse grained diorite. The bedrock is generally covered by a soil profile that developed in place from weathering of the rock over geologic time. The general soil profile is typical of residual soils produced by weathering of crystalline rock. The profile shows clayey surface soils grading with depth into sandy micaceous silt (or in some locations micaceous silty sand). The soils are of low to medium plasticity and are primarily ML, MH and some SM classifications in the United Soils Classification System. With increasing depth, the profile transitions to "partially weathered rock" having at least 100 blows per foot standard penetration resistance.

The degree of weathering becomes less as the sound rock is approached.

Sound rock has a rock quality designation (RQD)of 75 percent or more." McGuire Nuclear Station 7 Report Number: DUKCORP042-PR-002 2.3.2 Development of Base Case Profiles and Nonlinear Material Properties Table 2.3.2-1 is not used. Table 2.3.1-1 shows the recommended shear-wave velocities and unit weights verses depth for the best estimate single profile accommodating Unit 1 and Unit 2. In Table 2.3.1-1 depths begin at El. 760 ft. and the Deepest Foundation Elevation (SSE control point) was taken at El. 716.5 ft. El. 716.5 ft. reflects the top of the base of the mat foundation of the reactor buildings.

Based on Table 2.3.1-1 and the adopted location of the SSE control point at a depth of 43.5 ft. (13.2 m), the profile consists of 20.5 ft. (6.2 m) of firm rock overlying hard metamorphic basement rock.Shear-wave velocities for the materials below the bottom of the mat foundation to a depth of 56.5 ft. (17.2 m) were based on downhole measurements (Reference 9). For the material below a depth of 56.5 ft. (17.2 m), shear-wave velocities were based on extrapolations of measurements made in the "sound rock" with the recommended profile reaching hard reference rock conditions at an assumed depth of 64 ft. (19.5 m).Based on the specified shear-wave velocities reflecting a mixture of predominately measured values as well as assumed values, and considering the recommended shear-wave velocities follow the expected trend of increasing with depth, a scale factor of 1.25 was adopted to reflect upper and lower range base-cases.

The scale factor of 1.25 reflects a Orpln of about 0.2 based on the SPID (Reference

3) 1 0 th and g 0 th fractiles which implies a 1.28 scale factor on a,.Using the shear-wave velocities specified in Table 2.3.1-1, three base-profiles were developed using the scale factor of 1.25. The specified shear-wave velocities were taken as the mean or best estimate base-case profile (P1) with lower and upper range base-cases profiles P2 and P3 respectively.

The three base-case profiles P1, P2, and P3, have a mean depth below the SSE control point at El. 716.5 ft. of 20.5 ft. (6.2 m) to hard reference rock, randomized

+/- 4 ft. (+/- 1.2 m). The base-case profiles (P1, P2, and P3) are shown in Figure 2.3.2-1 and listed in Table 2.3.2-2. The depth randomization reflects +/- 20% of the depth and was included to provide a realistic broadening of the fundamental resonance rather than reflect actual random variations to basement shear-wave velocities across a footprint.

McGuire Nuclear Station 8 Report Number: DUKCORP042-PR-002 Vs profiles for McGuire Site Vs (ft/sec)4000 5000 6000 0 1000 2000 3000 7000 8000 9000 10000 0 10 20 30 10 -Profile 1-Profile 2--.Profile 3 Figure 2.3.2-1 Shear-wave velocity profiles for the McGuire site Table 2.3.2-2 Layer thicknesses, depths, and shear-wave velocities (V,) for three profiles, 0 4750 0 3800 1 0 5937 6.5 6.5 4750 6.5 6.5 3800 6.5 6.5 5937 6.5 13.0 7200 6.5 13.0 5760 6.5 13.0 9000 7.0 20.0 7200 7.0 20.0 5760 7.0 20.0 9000 0.5 20.5 7200 0.5 20.5 5760 0.5 20.5 9000 3280.8 3301.3 9285 3280.8 3301.3 9285 3280.8 3301.3 9285 2.3.2.1 Shear Modulus and Damping Curves No site-specific nonlinear dynamic material properties were determined for the firm rock materials in the initial siting of McGuire. The rock material over the upper 20.5 ft. (6.2 m)was assumed to have behavior that could be modeled as either linear or nonlinear.

To represent this potential for either case in the upper 20.5 ft. (6.2 m) of firm rock at the McGuire site, two sets of shear modulus reduction and hysteretic damping curves were used. Consistent with the SPID (Reference 3), the EPRI rock curves (model M1) were considered to be appropriate to represent the upper range nonlinearity likely in the materials at this site and linear analyses (model M2) was assumed to represent an equally plausible alternative rock response across loading level. For the linear analyses, the low strain damping from the EPRI rock curves was used as the constant damping values in the upper 20.5 ft. (6.2 m).McGuire Nuclear Station 9 Report Number: DUKCORP042-PR-002 2.3.2.2 Kappa For the McGuire profile of about 20.5 ft. (6.2 m) of firm rock over hard reference rock, the kappa value of 0.006s for hard rock (Reference

3) dominates profile damping. The 20.5 ft. (6.2 m) of firm rock, based on the low strain damping from the EPRI rock G/Gmax and hysteretic damping curves, reflects a contribution of only about 0.0003s (Table 2.3.2-3).As a result, the dominant epistemic uncertainty in low strain kappa was assumed to be incorporated in the reference rock hazard.Table 2.3.2-3 Kappa values and weights used for site response analyses Velocity Profile Kappa (s) Weights P1 0.0062 0.4 P2 0.0063 0.3 P3 0.0062 0.3 G/Gmax and Hysteretic Damping Curves M1 0.5 M2 0.5 2.3.3 Randomization of Base Case Profiles To account for the aleatory variability in dynamic material properties that is expected to occur across a site at the scale of a typical nuclear facility, variability in the assumed shear-wave velocity profiles has been incorporated in the site response calculations.

For the McGuire site, random shear-wave velocity profiles were developed from the base case profiles shown in Figure 2.3.2-1. Thirty random velocity profiles were generated for each base case profile. These random velocity profiles were generated using a natural log standard deviation of 0.25 over the upper 50 ft. and a natural log standard deviation of 0.15 below that depth. As specified in the SPID (Reference 3), correlation of shear-wave velocity between layers was modeled using the footprint correlation model. In the correlation model, a limit of +/- 2 standard deviations about the median value in each layer was assumed for the limits on random velocity fluctuations.

2.3.4 Input Spectra Consistent with the guidance in Appendix B of the SPID (Reference 3), input Fourier amplitude spectra were defined for a single representative earthquake magnitude (M 6.5) using two different assumptions regarding the shape of the seismic source spectrum (single-corner and double-corner).

A range of 11 different input amplitudes (median peak ground accelerations (PGA) ranging from 0.01g to 1.5g) was used in the site response analyses.

The characteristics of the seismic source and upper crustal attenuation properties assumed for the analysis of the McGuire site were the same as those identified in Tables B-4, B-5, B-6 and B-7 of the SPID (Reference

3) as appropriate for typical CEUS sites.2.3.5 Methodology To perform the site response analyses for the McGuire site, a random vibration theory (RVT) approach was employed.

This process utilizes a simple, efficient approach for computing site-specific amplification functions and is consistent with existing NRC guidance and the SPID (Reference 3). The guidance contained in Appendix B of the McGuire Nuclear Station 10 Report Number: DUKCORP042-PR-002 SPID (Reference

3) on incorporating epistemic uncertainty in shear-wave velocities, kappa, nonlinear dynamic properties and source spectra for plants with limited at-site information was followed for the McGuire site.2.3.6 Amplification Functions The results of the site response analysis consist of amplification factors (5% of critical damping pseudo absolute response spectra) which describe the amplification (or de-amplification) of hard reference rock motion as a function of frequency and input reference rock amplitude.

The amplification factors are represented in terms of a median amplification value and an associated standard deviation (sigma) for each oscillator frequency and input rock amplitude.

Consistent with the SPID (Reference

3) a minimum median amplification value of 0.5 was employed in the present analysis.Figure 2.3.6-1 illustrates the median and +/- 1 standard deviation in the predicted amplification factors developed for the eleven loading levels parameterized by the median reference (hard rock) peak acceleration (0.01g to 1.50g) for profile P1 and EPRI rock G/Gmax and hysteretic damping curves (model M1). The variability in the amplification factors results from variability in shear-wave velocity, depth to hard rock, and modulus reduction and hysteretic damping curves. To illustrate the effects of nonlinearity at the McGuire firm rock site, Figure 2.3.6-2 shows the corresponding amplification factors developed with linear site response analyses (model M2). Between the linear and nonlinear (equivalent-linear) analyses, Figure 2.3.6-1 and Figure 2.3.6-2 show only a minor difference across structural frequency as well as loading level.Tabulated values of the amplification factors are provided in Appendix A.McGuire Nuclear Station 11 Report Number: DUKCORP042-PR-002 C CC U M~~0-C-E CE INPUT MOTION 0.01G INPUT MOTION 0.LUG , i l~,, k # ,, .i , ,1= -i -.~l , .E l L,, --, , , j,lINPUT NOTION 0.05G INPUT MOTION 0.20G INPUT NOTION 0.40C INPUT MOTION 0.30G 10 2 10 2 1o -1 L o 0 10 1 Frequency (Hz)10 -1 10 0 10 1 Frequency (Hz)10 2 PMPLIFICflTION, [CGUIRE, MiPIK1 MI 6.5, 1 CORNER: PRGE 1 OF 2 Figure 2.3.6-1 Example suite of amplification factors (5% of critical damping pseudo absolute acceleration spectra) developed for the mean base-case profile (P1), EPRI rock modulus reduction and hysteretic damping curves (model Ml), and base-case kappa (Ki) at eleven loading levels of hard rock median peak acceleration values from 0.01g to 1.50g. M 6.5 and single-corner source model (Reference 3)McGuire Nuclear Station 12 Report Number: DUKCORP042-PR-002 CL F9 C-I 0-4-)(a C-1 C-)C DI PU T MO T I O N 0. 0 1G--C INPUT MOTION OLOG " C INPUT MtOTION 0.30G I ¢-n m.9-INPU IT l I I I III1l I II II1 INPUT NOTICN 'J.05G)-INPU I 0.20G* IIIII ILIIIIl-MOTIIY' 0.20G.2.*o INPUT NIOTION 0.40G 10 -1 LO 0 10 1 10 2 10 -1 10 0 10 Frequency C (Hz)10 2 Frequency (Hz)AMPLIFICATION, NCGUIRE, NiPIKI M 6.5, 1 CORNER: PAGE 1 OF 2 Figure 2.3.6-1 continued McGuire Nuclear Station Report Number: DUKCORP042-PR-002 13 C -09C 09 U CC 0 `E cc I I INPUT I I I 1 I IIII1 INPUT 0.01G 0 T INPUT MOTION 0.05G 0 1 1 -I -, , ----I .--- I l ~ l -----I ---l- -l 1 1 11 INPUT MOTION 0.10G-'"- vr .C 0 0 0=0 RJT OT------02 INPUT MOTION 0.30G 10 2 i0 -1 7UT MOTION 0.40G jo -i to 0 to I 10 0 10 1 Frequency (Hz)10 2 Frequency (Hz)ArMPLIFICATION, MCGUIRE, MEPIKI N 6.5, 1 CORNER: PAGE I OF 2 Figure 2.3.6-2 Example suite of amplification factors (5% of critical damping pseudo absolute acceleration spectra) developed for the mean base-case profile (P1), linear site response (model M2), and base-case kappa (K1) at eleven loading levels of hard rock median peak acceleration values from 0.01g to 1.50g. M 6.5 and single-corner source model (Reference 3)McGuire Nuclear Station 14 Report Number: DUKCORP042-PR-002 C)~0 CC 0 INPUT MOTION 0.50C 0 INPUT NOTION 1.00G INPUT MOTION 1.506 INPUT MOTION 0.75G INPUT MOTION 2.25G 10 -1 tO 0 10 Frequency 1 (Hz)1O 2 AMPLIFICATION, MCGUIRE, M2P1KI M 6.5, 1 CORNER: PAGE 2 OF 2 Figure 2.3.6-2 continued McGuire Nuclear Station Report Number: DUKCORP042-PR-002 15 2.3.7 Control Point Seismic Hazard Curves The procedure to develop probabilistic site-specific control point hazard curves used in the present analysis follows the methodology described in Section B-6.0 of the SPID (Reference 3). This procedure (referred to as Method 3 from NUREG/CR-6728 (Reference 16)) computes a site-specific control point hazard curve for a broad range of spectral accelerations given the site-specific bedrock hazard curve and site-specific estimates of soil or soft-rock response and associated uncertainties.

This process is repeated for each of the seven spectral frequencies for which ground motion equations are available.

The dynamic response of the materials below the control point was represented by the frequency-and amplitude-dependent amplification functions (median values and standard deviations) developed and described in the previous section. The resulting control point mean hazard curves for McGuire are shown in Figure 2.3.7-1 for the seven spectral frequencies for which ground motion equations are defined. Tabulated values of mean and fractile seismic hazard curves and site response amplification functions are provided in Appendix A.Total Mean Soil Hazard by Spectral Frequency at McGuire S 1E --- -i .......aJ -25 Hz 0)G-10 Hz 5Hz-PGA U GD-2.5 H WD -1 Hz 1u -0.5 Hz r- 1E-6 -_ _1E-7 0.01 0.1 1 10 Spectral acceleration (g)Figure 2.3.7-1 Control point mean hazard curves for spectral frequencies of 0.5, 1, 2.5, 5, 10, 25 and 100 Hz (PGA) at McGuire (5% of critical damping)McGuire Nuclear Station 16 Report Number: DUKCORP042-PR-002 2.4 CONTROL POINT RESPONSE SPECTRA The control point mean hazard curves described above have been used to develop uniform hazard response spectra (UHRS) and the GMRS. The UHRS were obtained through linear interpolation in log-log space to estimate the spectral acceleration at each spectral frequency for the 1 E-4 and 1 E-5 per year hazard levels. The 1 E-4 and 1 E-5 UHRS along with a design factor (DF) are used to compute the GMRS at the control point using the criteria in NRC Reg. Guide 1.208 (Reference 7). Figure 2.4-1 shows the control point UHRS and GMRS. Table 2.4-1 shows the UHRS and GMRS spectral accelerations for each of the seven frequencies.

Mean Soil UHRS and GMRS at McGuire 1.5 1.25 1-o 1 4..u 0.75 U 0.5 C.0.25 0.-1E-5 UHRS 1GMRS-1E-4 UHRS 100 0.1 1 10 Spectral frequency, Hz Figure 2.4-1 Plots of 1 E-4 and 1 E-5 uniform hazard spectra and GMRS at control point for McGuire (5% of critical damping response spectra)McGuire Nuclear Station 17 Report Number: DUKCORP042-PR-002 Table 2.4-1 UHRS and GMRS at control point for McGuire (5% of critical damping respo se spectra)Freg (Hz) 1E-4 UHRS (g) 1E-5 UHRS (g) GMRS (g)100 1.92E-01 6.48E-01 3.05E-01 90 1.95E-01 6.60E-01 3.10E-01 80 2.01 E-01 6.86E-01 3.22E-01 70 2.16E-01 7.50E-01 3.51E-01 60 2.56E-01 9.10E-01 4.24E-01 50 3.37E-01 1.22E+00 5.65E-01 40 4.03E-01 1.44E+00 6.70E-01 35 4.11E-01 1.45E+00 6.76E-01 30 4.06E-01 1.41 E+00 6.60E-01 25 3.93E-01 1.34E+00 6.29E-01 20 3.84E-01 1.28E+00 6.03E-01 15 3.65E-01 1.18E+00 5.59E-01 12.5 3.49E-01 1.11E+00 5.28E-01 10 3.26E-01 1.02E+00 4.86E-01 9 3.09E-01 9.50E-01 4.55E-01 8 2.90E-01 8.75E-01 4.21 E-01 7 2.68E-01 7.96E-01 3.84E-01 6 2.45E-01 7.11E-01 3.44E-01 5 2.17E-01 6.16E-01 3.OOE-01 4 1.80E-01 4.91E-01 2.41E-01 3.5 1.59E-01 4.24E-01 2.09E-01 3 1.37E-01 3.58E-01 1.77E-01 2.5 1.14E-01 2.88E-01 1.43E-01 2 1.05E-01 2.58E-01 1.29E-01 1.5 8.66E-02 2.06E-01 1.04E-01 1.25 7.49E-02 1.75E-01 8.86E-02 1 6.47E-02 1.47E-01 7.49E-02 0.9 6.25E-02 1.42E-01 7.24E-02 0.8 6.05E-02 1.38E-01 7.OOE-02 0.7 5.77E-02 1.31 E-01 6.69E-02 0.6 5.35E-02 1.22E-01 6.20E-02 0.5 4.70E-02 1.07E-01 5.44E-02 0.4 3.76E-02 8.55E-02 4.35E-02 0.35 3.29E-02 7.48E-02 3.81E-02 0.3 2.82E-02 6.41 E-02 3.26E-02 0.25 2.35E-02 5.35E-02 2.72E-02 0.2 1.88E-02 4.28E-02 2.18E-02 0.15 1.41E-02 3.21E-02 1.63E-02 0.125 1.1 7E-02 2.67E-02 1.36E-02 0.1 9.39E-03 2.14E-02 1.09E-02 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 18 3 Plant Design Basis Ground Motion The current licensing basis SSE is based on an evaluation of the maximum earthquake potential considering regional and local geology and seismic history (Reference 10, Former Appendix 2E). Historical records indicate that the maximum earthquake intensity experienced at the site was the Charleston earthquake of August 31, 1886 with an estimated site surface intensity between VI and VII MM (Reference 10, Former Appendix 2E, Section 4.1). Since there is an absence of geologic structure that can be related to earthquakes, it is necessary to presume that the observed epicentral intensities of historical earthquakes in the region could occur anywhere within the region or even in the immediate vicinity of the site (Reference 10, Former Appendix 2E, Section 4.2).3.1 SSE DESCRIPTION OF SPECTRAL SHAPE The McGuire SSE is defined in terms of a PGA and a design response spectrum shape.Considering a site design intensity between VII and VIII (7.5), the maximum horizontal ground acceleration is defined with 15% of gravity (0.15g) as the anchor point for the SSE (Reference 10, Section 2.5). The site design response spectrum for the McGuire SSE is based on a Newmark-type spectral shape (Reference 10, Former Appendix 2E, Section 4.4).For the purposes of NTTF 2.1: Seismic screening, the spectral acceleration values for the McGuire horizontal SSE (5% of critical damping) are shown as a function of frequency in Table 3.1-1 and plotted in Figure 3.1-1. The SSE acceleration values are based on data from Former Appendix 2E Figure 2E-4 of the McGuire Updated Final Safety Analysis Report (UFSAR) (Reference 10).Table 3.1-1 Horizontal SSE for McGuire (5% of critical dampin9 response spectrum)Frequency (Hz) I Spectral Acceleration (g)0.33 0.06 2 0.36 6 0.36 35/PGA 0.15 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 19 Horizontal SSE for McGuire 0.50 0.45 0.40 0.35.2 0.30 0.25"F 0.20 L-U0.15 0.10 0.05 0.00 0.1 1 10 Spectral frequency, Hz 100 Figure 3.1-1 Horizontal SSE for McGuire (5% of critical damping response spectrum)3.2 CONTROL POINT ELEVATION The McGuire UFSAR defines the SSE control point at the top of sound rock (Reference 10, Section 3.7). Since the elevation at the top of sound rock varies throughout the site (Reference 9, page 8) and all major Category 1 structures are founded on sound rock (Reference 10, Section 3.7), the SSE control point elevation is taken to be at EL. 716.5, which is at the base of the mat foundation of the Reactor Buildings.

This definition of the control point is consistent with the approach described in the SPID (Reference 3, Section 2.4.2).McGuire Nuclear Station 20 Report Number: DUKCORP042-PR-002 4 Screening Evaluation In accordance with the SPID, Section 3 (Reference 3), a screening evaluation was performed for McGuire as described below.4.1 RISK EVALUATION SCREENING (1 TO 10 Hz)In the 1 to 10 Hz part of the response spectrum, the GMRS exceeds the SSE for McGuire. Therefore, McGuire screens in for a risk evaluation.

4.2 HIGH FREQUENCY SCREENING

(> 10 Hz)Above 10 Hz, the GMRS exceeds the SSE for McGuire. The high frequency exceedances can be addressed in the risk evaluation discussed in Section 4.1 above.4.3 SPENT FUEL POOL EVALUATION SCREENING (1 TO 10 Hz)In the 1 to 10 Hz part of the response spectrum, the GMRS exceeds the SSE for McGuire. Therefore, McGuire screens in for a spent fuel pool integrity evaluation.

McGuire Nuclear Station 21 Report Number: DUKCORP042-PR-002 5 Interim Actions and Assessments As described in Section 4, the GMRS developed in response to the NTTF 2.1: Seismic portion of the 10 CFR 50.54(f) Request for Information dated March 12, 2012 (Reference

1) exceeds the design basis SSE. The NRC 50.54(f) letter (Reference

1) requests: "interim evaluation and actions taken or planned to address the higher seismic hazard relative to the design basis, as appropriate, prior to completion of the risk evaluation." These evaluations and actions are discussed below.Consistent with NRC letter dated February 20, 2014 (Reference 17), the seismic hazard reevaluations presented herein are distinct from the current design and licensing bases of McGuire. Therefore, the results do not call into question the operability or functionality of SSCs and are not reportable pursuant to 10 CFR 50.72, "Immediate notification requirements for operating nuclear power reactors" (Reference 2, Section 50.72) and 10 CFR 50.73, "Licensee event report system" (Reference 2, Section 50.73).5.1 EXPEDITED SEISMIC EVALUATION PROGRAM An expedited seismic evaluation process (ESEP) is being performed at McGuire in accordance with the methodology in EPRI 3002000704 (Reference

4) as proposed in a letter to the NRC dated April 9, 2013 (Reference

11) and agreed to by the NRC in a letter dated May 7, 2013 (Reference 12). Duke plans to submit a report on the ESEP to the NRC in December 2014 (Reference 15), in accordance with the schedule in the Nuclear Energy Institute (NEI) April 9, 2013 letter to the NRC (Reference 11).5.2 SEISMIC RISK ESTIMATES The NRC letter (Reference

17) also requests that licensees provide an interim evaluation or actions to address the higher seismic hazard relative to the design basis while the expedited approach and risk evaluations are conducted.

In response to that request, the NEI letter dated March 12, 2014 (Reference

14) provides seismic core damage risk estimates using the updated seismic hazards for the operating nuclear plants in the CEUS. These risk estimates continue to support the following conclusions of the NRC GI-199 Safety/Risk Assessment (Reference 13): "Overall seismic core damage risk estimates are consistent with the Commission's Safety Goal Policy Statement because they are within the subsidiary objective of 10 4/year for core damage frequency.

The GI-1 99 Safety/Risk Assessment, based in part on information from the U.S. Nuclear Regulatory Commission's (NRC's)Individual Plant Examination of External Events (IPEEE) program, indicates that no concern exists regarding adequate protection and that the current seismic design of operating reactors provides a safety margin to withstand potential earthquakes exceeding the original design basis." McGuire is included in the March 12, 2014 risk estimates (Reference 14). Using the methodology described in the NEI letter (Reference 14), the seismic core damage risk McGuire Nuclear Station 22 Report Number: DUKCORP042-PR-002 estimates for all plants were shown to be below 1 E-4/year; thus, the above conclusions apply.5.3 INDIVIDUAL PLANT EXAMINATION OF EXTERNAL EVENTS An evaluation of beyond-design-basis ground motions was performed for McGuire as part of the IPEEE program. The SPRA methodology was utilized to perform the IPEEE seismic evaluation for McGuire (Reference 21). The results of the SPRA determined the SCDF for McGuire to be less than the Commission's Safety Goal subsidiary objective of 1E-4/year (References 22 and 13). The McGuire IPEEE seismic evaluation (Reference

21) concluded that there are no fundamental weaknesses or vulnerabilities with regard to severe accident risk, including seismic, and confirmed that the plant poses no undue risk to the public health and safety. Additionally, improvements were made to the plant based on the McGuire IPEEE seismic evaluation, as confirmed in the NTTF 2.3 seismic walkdown report (Reference 19), to enhance the McGuire seismic margin.5.4 WALKDOWNS TO ADDRESS NRC FUKUSHIMA NTTF RECOMMENDATION 2.3 Walkdowns have been completed for McGuire in accordance with the EPRI seismic walkdown guidance (Reference 18); including inaccessible items (References 19 and 20). Potentially adverse seismic conditions (PASC) found were entered into the corrective action program (CAP) for resolution.

None of the PASC items challenged operability of the plant. There were no vulnerabilities identified under IPEEE, however, previously identified IPEEE enhancements were reviewed and found to be complete.Duke confirmed through the walkdowns that the existing monitoring and maintenance procedures keep the plant consistent with the licensing basis (References 19 and 20).McGuire Nuclear Station 23 Report Number: DUKCORP042-PR-002 6 Conclusions In accordance with the 50.54(f) letter (Reference 1), a seismic hazard and screening evaluation was performed for McGuire. A GMRS was developed solely for the purpose of screening for additional evaluations in accordance with the SPID (Reference 3).Based on the results of the screening evaluation, McGuire screens in for a risk evaluation and a spent fuel pool integrity evaluation.

McGuire Nuclear Station 24 Report Number: DUKCORP042-PR-002 7 References

1. NRC (E. Leeds and M. Johnson) Letter to All Power Reactor Licensees et al., Request for Information Pursuant to Title 10 of the Code of Federal Regulations 50.54(f) Regarding Recommendations 2.1, 2.3, and 9.3 of the Near-Term Task Force Review of Insights from the Fukushima Dai-ichi Accident, dated March 12, 2012, ADAMS Accession No. ML12053A340.

2. Title 10 Code of Federal Regulations Part 50.3. EPRI 1025287, Seismic Evaluation Guidance:

Screening, Prioritization and Implementation Details (SPID) for the Resolution of Fukushima Near-Term Task Force Recommendation 2.1: Seismic, Palo Alto, CA, February 2013.4. EPRI 3002000704, Seismic Evaluation Guidance:

Augmented Approach for the Resolution of Fukushima Near-Term Task Force Recommendation 2.1: Seismic, Palo Alto, CA, May 2013.5. EPRI 1021097 (NUREG-2115), Central and Eastern United States Seismic Source Characterization for Nuclear Facilities, Palo Alto, CA, January 2012.6. EPRI 3002000717, EPRI (2004, 2006) Ground-Motion Model (GMM) Review Project, Palo Alto, CA, June 2013.7. NRC Regulatory Guide 1.208, A performance-based approach to define the site-specific earthquake ground motion, 2007.8. EPRI RSM-092513-030, McGuire Seismic Hazard and Screening Report, dated October 31, 2013.9. AMEC Project No. 6234-12-0031, Data for Site Amplifications

-McGuire Phase 2 EPRI Seismic Attenuation and GMRS Project, McGuire Nuclear Station, dated July 26, 2012.10. Duke Energy Company, McGuire Nuclear Station, Units I and 2, Updated Final Safety Analysis Report (UFSAR), Revision 17.11. NEI (A. R. Pietrangelo)

Letter to the NRC, Proposed Path Forward for NTTF Recommendation 2.1: Seismic Reevaluations, dated April 9, 2013, ADAMS Accession No. ML13101A379.

12. NRC (E. Leeds) Letter to NEI (J. Pollock), Electric Power Research Institute Final Draft Report XXXOX , "Seismic Evaluation Guidance:

Augmented Approach for the Resolution of Fukushima Near-Term Task Force Recommendation 2.1: Seismic,"as an Acceptable Alternative to the March 12, 2012, Information Request for Seismic Reevaluations, dated May 7, 2013, ADAMS Accession No. ML13106A331.

McGuire Nuclear Station 25 Report Number: DUKCORP042-PR-002

13. NRC Memorandum (from P. Hiland to B. Sheron), "Safety/Risk Assessment Results for Generic Issue 199, Implications of Updated Probabilistic Seismic Hazard Estimates in Central and Eastern United States on Existing Plants," dated September 2, 2010, ADAMS Accession No. ML1 00270582.14. NEI (A. R. Pietrangelo)

Letter to the NRC, Seismic Risk Evaluations for Plants in the Central and Eastern United States, dated March 12, 2014.15. Duke Energy (B. Waldrep) Letter to the NRC, Duke Energy Response to NRC Request for Information Pursuant to 10 CFR 50.54(f) Regarding the Seismic Aspects of recommendation 2.1 of the Near-Term Task Force Review of Insights from the Fukushima Dai-ichi Accident, dated April 26, 2013, ADAMS Accession No.ML13121A061.

16. NUREG/CR-6728, Technical Basis for Revision of Regulatory Guidance on Design Ground Motions: Hazard- and Risk- Consistent Ground Motion Spectra Guidelines, October 2001.17. NRC (E. Leeds) Letter to All Power Reactor Licensees et al., Supplemental Information Related to Request for Information Pursuant to Title 10 of the Code of Federal Regulations 50.54(f) Regarding Seismic Hazard Reevaluations for Recommendation 2.1 of the Near-Term Task Force Review of Insights from the Fukushima Dai-ichi Accident, dated February 20, 2014, ADAMS Accession No.ML14030A046.

18. EPRI 1025286, Seismic Walkdown Guidance for Resolution of Fukushima Near-Term Task Force Recommendation 2.3: Seismic, Palo Alto, CA, June 2012.19. Duke Energy Carolinas (S. Capps) Letter to the NRC, McGuire Nuclear Station (MNS), Units I and 2, Seismic Walkdown Information Requested by NRC Letter, Request for Information Pursuant to Title 10 of the Code of Federal Regulations 50.54(f) Regarding Recommendations 2.1, 2.3, and 9.3 of the Near-Term Task Force Review of Insights from the Fukushima Dai-ichi Accident, dated March 12, 2012, dated November 26, 2012, ADAMS Accession No. ML13003A339.

20. Duke Energy Carolinas (S. Capps) Letter to the NRC, McGuire Nuclear Station (MNS), Unit 1, Response to NRC Request for Information Pursuant to Title 10 Code of Federal Regulations 50.54(f) Regarding Seismic Aspects of Recommendation 2.3 of the Near Term Task Force Review of Insights from the Fukushima Dai-ichi Accident, dated June 20, 2013, ADAMS Accession No. ML13190A272.

21. Duke Power Company (T. McMeekin)

Letter to the NRC, McGuire Nuclear Station, Units I and 2, Individual Plant Examination of External Events (IPEEE) Submittal, dated June 1, 1994.22. NRC (F. Rinaldi) Letter to Duke Energy Corporation (H. Barron), Review of McGuire Nuclear Station, Units 1 and 2 -Individual Plant Examination of External Events Submittal (TAC Nos. M83639 and M83640), dated February 16, 1999.McGuire Nuclear Station 26 Report Number: DUKCORP042-PR-002 A.-Additional Tables Table A-la Mean and fractile seismic hazard curves for PGA at McGuire, 5% of critical damping AMPS(a)MEAN 0.05 0.16 0.50 0.84 0.95 0.0005 5.21 E-02 3.33E-02 4.43E-02 5.27E-02 6.OOE-02 6.54E-02 0.001 4.15E-02 2.35E-02 3.42E-02 4.19E-02 4.98E-02 5.50E-02 0.005 1.58E-02 7.03E-03 1.08E-02 1.53E-02 1.95E-02 2.92E-02 0.01 8.18E-03 3.28E-03 4.77E-03 7.45E-03 1.04E-02 1.90E-02 0.015 5.16E-03 1.82E-03 2.64E-03 4.43E-03 6.83E-03 1.38E-02 0.03 2.07E-03 5.20E-04 7.77E-04 1.49E-03 2.96E-03 7.13E-03 0.05 9.66E-04 1.79E-04 2.80E-04 5.91E-04 1.40E-03 3.90E-03 0.075 5.06E-04 7.66E-05 1.27E-04 2.80E-04 7.13E-04 2.19E-03 0.1 3.14E-04 4.37E-05 7.45E-05 1.72E-04 4.31E-04 1.38E-03 0.15 1.56E-04 2.07E-05 3.79E-05 8.85E-05 2.16E-04 6.64E-04 0.3 4.50E-05 5.66E-06 1.16E-05 2.84E-05 6.73E-05 1.57E-04 0.5 1.70E-05 1.98E-06 4.31E-06 1.13E-05 2.72E-05 5.27E-05 0.75 7.41E-06 7.77E-07 1.72E-06 4.90E-06 1.21 E-05 2.25E-05 1. 3.92E-06 3.63E-07 8.23E-07 2.53E-06 6.54E-06 1.21 E-05 1.5 1.46E-06 1.07E-07 2.53E-07 8.72E-07 2.46E-06 4.83E-06 3. 2.03E-07 7.55E-09 2.1OE-08 9.79E-08 3.23E-07 7.77E-07 5. 3.50E-08 7.34E-10 2.22E-09 1.32E-08 5.20E-08 1.55E-07 7.5 7.02E-09 1.77E-10 3.63E-10 2.13E-09 9.51E-09 3.47E-08 10. 1.99E-09 1.16E-10 1.64E-10 5.66E-10 2.57E-09 1.05E-08 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 27 Table A-lb Mean and fractile seismic hazard curves for 25 Hz at McGuire, 5% of critical damping AMPS(g) MEAN 0.05 0.16 0.50 0.84 0.95 0.0005 5.68E-02 4.13E-02 5.05E-02 5.75E-02 6.36E-02 6.83E-02 0.001 4.82E-02 3.19E-02 4.13E-02 4.83E-02 5.58E-02 6.09E-02 0.005 2.39E-02 1.27E-02 1.79E-02 2.35E-02 2.88E-02 3.84E-02 0.01 1.48E-02 7.03E-03 1.02E-02 1.40E-02 1.82E-02 2.76E-02 0.015 1.05E-02 4.70E-03 6.83E-03 9.79E-03 1.32E-02 2.13E-02 0.03 5.21E-03 2.01E-03 2.92E-03 4.56E-03 6.83E-03 1.25E-02 0.05 2.78E-03 9.11E-04 1.32E-03 2.29E-03 3.84E-03 7.55E-03 0.075 1.57E-03 4.37E-04 6.45E-04 1.20E-03 2.25E-03 4.77E-03 0.1 1.02E-03 2.49E-04 3.79E-04 7.34E-04 1.49E-03 3.28E-03 0.15 5.30E-04 1.11E-04 1.74E-04 3.63E-04 7.77E-04 1.79E-03 0.3 1.62E-04 2.88E-05 5.05E-05 1.11E-04 2.35E-04 5.27E-04 0.5 6.51E-05 1.13E-05 2.13E-05 4.77E-05 9.93E-05 1.87E-04 0.75 3.1OE-05 5.20E-06 1.02E-05 2.35E-05 4.98E-05 8.23E-05 1. 1.80E-05 2.88E-06 5.83E-06 1.38E-05 2.92E-05 4.70E-05 1.5 7.99E-06 1.15E-06 2.46E-06 6.09E-06 1.32E-05 2.1OE-05 3. 1.65E-06 1.87E-07 4.13E-07 1.18E-06 2.80E-06 4.77E-06 5. 4.19E-07 3.47E-08 8.OOE-08 2.72E-07 7.13E-07 1.34E-06 7.5 1.21 E-07 7.23E-09 1.77E-08 7.03E-08 2.07E-07 4.31E-07 10. 4.56E-08 2.10E-09 5.42E-09 2.39E-08 7.77E-08 1.74E-07 Table A-ic Mean and fractile seismic hazard curves for 10 Hz at McGuire, 5% of critical damping AMPS(g) MEAN 0.05 0.16 0.50 0.84 0.95 0.0005 6.1OE-02 4.98E-02 5.42E-02 6.09E-02 6.73E-02 7.13E-02 0.001 5.36E-02 4.07E-02 4.70E-02 5.42E-02 6.OOE-02 6.45E-02 0.005 2.80E-02 1.67E-02 2.16E-02 2.80E-02 3.42E-02 3.95E-02 0.01 1.72E-02 9.11E-03 1.23E-02 1.69E-02 2.16E-02 2.72E-02 0.015 1.20E-02 6.OOE-03 8.12E-03 1.16E-02 1.53E-02 2.04E-02 0.03 5.65E-03 2.49E-03 3.37E-03 5.27E-03 7.45E-03 1.11E-02 0.05 2.85E-03 1.07E-03 1.51 E-03 2.49E-03 3.95E-03 6.36E-03 0.075 1.52E-03 4.90E-04 7.13E-04 1.25E-03 2.19E-03 3.79E-03 0.1 9.36E-04 2.64E-04 4.01 E-04 7.34E-04 1.38E-03 2.49E-03 0.15 4.49E-04 1.07E-04 1.69E-04 3.37E-04 6.73E-04 1.29E-03 0.3 1.18E-04 2.22E-05 3.95E-05 8.60E-05 1.82E-04 3.37E-04 0.5 4.29E-05 7.34E-06 1.42E-05 3.23E-05 6.83E-05 1.16E-04 0.75 1.89E-05 3.01E-06 6.OOE-06 1.44E-05 3.09E-05 5.05E-05 1. 1.04E-05 1.53E-06 3.14E-06 7.89E-06 1.72E-05 2.80E-05 1.5 4.20E-06 5.42E-07 1.16E-06 3.09E-06 7.03E-06 1.16E-05 3. 7.19E-07 6.93E-08 1.53E-07 4.83E-07 1.21 E-06 2.25E-06 5. 1.55E-07 1.05E-08 2.46E-08 9.24E-08 2.60E-07 5.42E-07 7.5 3.89E-08 1.87E-09 4.63E-09 2.04E-08 6.45E-08 1.51 E-07 10. 1.32E-08 5.42E-10 1.32E-09 6.17E-09 2.19E-08 5.42E-08 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 28 Table A-id Mean and fractile seismic hazard curves for 5 Hz at McGuire, 5% of critical damping AMPS(g) MEAN 0.05 0.16 0.50 0.84 0.95 0.0005 6.14E-02 4.98E-02 5.50E-02 6.17E-02 6.83E-02 7.23E-02 0.001 5.41 E-02 4.01 E-02 4.63E-02 5.42E-02 6.17E-02 6.64E-02 0.005 2.63E-02 1.46E-02 1.98E-02 2.60E-02 3.33E-02 3.73E-02 0.01 1.49E-02 7.45E-03 1.05E-02 1.46E-02 1.95E-02 2.29E-02 0.015 9.77E-03 4.63E-03 6.64E-03 9.51 E-03 1.31 E-02 1.57E-02 0.03 4.04E-03 1.69E-03 2.42E-03 3.79E-03 5.58E-03 7.45E-03 0.05 1.84E-03 6.54E-04 9.65E-04 1.64E-03 2.68E-03 3.84E-03 0.075 9.OOE-04 2.72E-04 4.19E-04 7.55E-04 1.36E-03 2.1OE-03 0.1 5.17E-04 1.40E-04 2.19E-04 4.19E-04 7.89E-04 1.29E-03 0.15 2.24E-04 5.20E-05 8.60E-05 1.72E-04 3.47E-04 5.91 E-04 0.3 4.95E-05 9.37E-06 1.72E-05 3.73E-05 7.89E-05 1.32E-04 0.5 1.60E-05 2.64E-06 5.12E-06 1.23E-05 2.64E-05 4.25E-05 0.75 6.41 E-06 9.11 E-07 1.90E-06 4.83E-06 1.07E-05 1.74E-05 1. 3.25E-06 4.13E-07 8.85E-07 2.35E-06 5.50E-06 9.11 E-06 1.5 1.17E-06 1.23E-07 2.72E-07 8.OOE-07 1.98E-06 3.52E-06 3. 1.61 E-07 9.93E-09 2.49E-08 9.24E-08 2.76E-07 5.58E-07 5. 2.93E-08 1.15E-09 3.05E-09 1.38E-08 4.98E-08 1.13E-07 7.5 6.39E-09 2.42E-10 5.27E-10 2.46E-09 1.05E-08 2.64E-08 10. 1.98E-09 1.53E-10 2.07E-10 7.03E-10 3.09E-09 8.60E-09 Table A-le Mean and fractile seismic hazard curves for 2.5 Hz at McGuire, 5% of critical damping AMPS(g) MEAN 0.05 0.16 0.50 0.84 0.95 0.0005 5.71 E-02 4.37E-02 4.90E-02 5.75E-02 6.45E-02 6.93E-02 0.001 4.67E-02 3.19E-02 3.79E-02 4.63E-02 5.58E-02 6.09E-02 0.005 1.70E-02 8.98E-03 1.20E-02 1.64E-02 2.22E-02 2.60E-02 0.01 8.25E-03 3.90E-03 5.35E-03 7.89E-03 1.11 E-02 1.38E-02 0.015 4.90E-03 2.10E-03 2.96E-03 4.56E-03 6.73E-03 8.85E-03 0.03 1.68E-03 5.58E-04 8.47E-04 1.49E-03 2.49E-03 3.52E-03 0.05 6.42E-04 1.72E-04 2.72E-04 5.20E-04 1.01 E-03 1.53E-03 0.075 2.69E-04 5.91 E-05 9.93E-05 2.04E-04 4.31 E-04 7.03E-04 0.1 1.38E-04 2.68E-05 4.63E-05 9.79E-05 2.22E-04 3.84E-04 0.15 5.11 E-05 8.47E-06 1.55E-05 3.47E-05 8.23E-05 1.46E-04 0.3 9.01 E-06 1.11 E-06 2.25E-06 5.91 E-06 1.49E-05 2.64E-05 0.5 2.54E-06 2.32E-07 5.27E-07 1.57E-06 4.31 E-06 8.OOE-06 0.75 9.16E-07 6.09E-08 1.53E-07 5.27E-07 1.60E-06 3.09E-06 1. 4.30E-07 2.16E-08 5.83E-08 2.29E-07 7.55E-07 1.53E-06 1.5 1.38E-07 4.37E-09 1.34E-08 6.26E-08 2.42E-07 5.27E-07 3. 1.50E-08 2.80E-10 7.77E-10 4.56E-09 2.46E-08 6.45E-08 5. 2.26E-09 1.25E-10 1.64E-10 5.42E-10 3.33E-09 1.02E-08 7.5 4.23E-10 9.24E-11 1.16E-10 1.72E-10 6.26E-10 1.98E-09 10. 1.17E-10 9.11E-11 1.01E-10 1.53E-10 2.42E-10 6.17E-10 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 29 Table A-if Mean and fractile seismic hazard curves for 1 Hz at McGuire, 5% of critical damping AMPS(g)MEAN 0.05 0.16 0.50 0.84 0.95 0.0005 4.08E-02 2.32E-02 3.05E-02 4.19E-02 5.05E-02 5.58E-02 0.001 2.79E-02 1.40E-02 1.95E-02 2.84E-02 3.52E-02 4.13E-02 0.005 7.74E-03 3.14E-03 4.70E-03 7.34E-03 1.07E-02 1.36E-02 0.01 3.73E-03 1.11E-03 1.82E-03 3.33E-03 5.58E-03 7.55E-03 0.015 2.16E-03 5.12E-04 8.98E-04 1.84E-03 3.37E-03 4.90E-03 0.03 6.29E-04 9.79E-05 1.87E-04 4.70E-04 1.02E-03 1.74E-03 0.05 1.96E-04 2.25E-05 4.63E-05 1.27E-04 3.33E-04 6.17E-04 0.075 6.79E-05 6.45E-06 1.38E-05 3.90E-05 1.16E-04 2.25E-04 0.1 3.03E-05 2.57E-06 5.58E-06 1.62E-05 5.20E-05 1.02E-04 0.15 9.44E-06 6.93E-07 1.53E-06 4.63E-06 1.60E-05 3.28E-05 0.3 1.38E-06 6.36E-08 1.62E-07 6.OOE-07 2.29E-06 5.35E-06 0.5 3.70E-07 9.65E-09 2.88E-08 1.32E-07 5.91E-07 1.55E-06 0.75 1.29E-07 1.92E-09 6.54E-09 3.68E-08 2.01 E-07 5.75E-07 1. 5.91E-08 6.26E-10 2.13E-09 1.36E-08 8.72E-08 2.72E-07 1.5 1.83E-08 1.90E-10 4.56E-10 3.05E-09 2.42E-08 8.60E-08 3. 1.93E-09 1.01 E-10 1.49E-10 2.53E-10 1.92E-09 8.72E-09 5. 2.91E-10 9.11E-11 1.01E-10 1.53E-10 3.05E-10 1.29E-09 7.5 5.53E-11 9.11E-11 1.01E-10 1.53E-10 1.55E-10 3.05E-10 10. 1.56E-11 9.11E-11 9.11E-11 1.53E-10 1.53E-10 1.69E-10 Table A-lg Mean and fractile seismic hazard curves for 0.5 Hz at McGuire, 5% of critical damping AMPS(g) MEAN 0.05 0.16 0.50 0.84 0.95 0.0005 2.30E-02 1.31 E-02 1.77E-02 2.25E-02 2.84E-02 3.33E-02 0.001 1.44E-02 7.66E-03 1.02E-02 1.38E-02 1.84E-02 2.29E-02 0.005 4.17E-03 1.16E-03 1.95E-03 3.79E-03 6.45E-03 8.35E-03 0.01 1.97E-03 3.09E-04 6.17E-04 1.57E-03 3.33E-03 4.90E-03 0.015 1.10E-03 1.20E-04 2.60E-04 7.77E-04 1.92E-03 3.14E-03 0.03 2.94E-04 1.77E-05 4.25E-05 1.62E-04 5.12E-04 1.05E-03 0.05 8.60E-05 3.57E-06 8.85E-06 3.73E-05 1.49E-04 3.37E-04 0.075 2.83E-05 9.24E-07 2.35E-06 9.93E-06 4.83E-05 1.15E-04 0.1 1.22E-05 3.47E-07 9.24E-07 3.68E-06 2.07E-05 4.98E-05 0.15 3.61E-06 8.47E-08 2.35E-07 9.24E-07 5.75E-06 1.53E-05 0.3 4.78E-07 6.45E-09 1.98E-08 9.65E-08 6.45E-07 2.35E-06 0.5 1.22E-07 8.60E-10 2.84E-09 1.79E-08 1.42E-07 6.45E-07 0.75 4.25E-08 2.32E-10 6.17E-10 4.31 E-09 4.25E-08 2.25E-07 1. 1.98E-08 1.53E-10 2.57E-10 1.51 E-09 1.72E-08 1.04E-07 1.5 6.46E-09 1.04E-10 1.53E-10 3.79E-10 4.37E-09 3.23E-08 3. 7.73E-10 9.11E-11 1.01E-10 1.53E-10 3.95E-10 3.33E-09 5. 1.31E-10 9.11E-11 1.01E-10 1.53E-10 1.57E-10 5.50E-10 7.5 2.78E-11 9.11E-11 9.11E-11 1.53E-10 1.53E-10 1.92E-10 10. 8.48E-12 9.11E-11 9.11E-11 1.53E-10 1.53E-10 1.53E-10 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 30 Table A- 2 Amplification functions for McGuire, 5% of critical damping PGA Median Sigma 25 Hz Median Sigma 10 Hz Median Sigma 5 Hz Median Sigma AF ln(AF) An Sg(AF) AF ln(AF) AF In(AF)1.OOE-02 9.89E-01 1.29E-01 1.30E-02 1.OOE+00 1.27E-01 1.90E-02 1.03E+00 1.29E-01 2.09E-02 1.04E+00 1.32E-01 4.95E-02 1.02E+00 1.23E-01 1.02E-01 1.04E+00 1.28E-01 9.99E-02 1.04E+00 1.29E-01 8.24E-02 1.05E+00 1.31 E-01 9.64E-02 1.04E+00 1.22E-01 2.13E-01 1.05E+00 1.28E-01 1.85E-01 1.05E+00 1.29E-01 1.44E-01 1.05E+00 1.31 E-01 1.94E-01 1.05E+00 1.22E-01 4.43E-01 1.05E+00 1.28E-01 3.56E-01 1.05E+00 1.28E-01 2.65E-01 1.05E+00 1.31 E-01 2.92E-01 1.05E+00 1.22E-01 6.76E-01 1.05E+00 1.29E-01 5.23E-01 1.05E+00 1.28E-01 3.84E-01 1.05E+00 1.31 E-01 3.91 E-01 1.06E+00 1.23E-01 9.09E-01 1.05E+00 1.29E-01 6.90E-01 1.05E+00 1.28E-01 5.02E-01 1.05E+00 1.31 E-01 4.93E-01 1.06E+00 1.23E-01 1.15E+00 1.05E+00 1.30E-01 8.61E-01 1.05E+00 1.28E-01 6.22E-01 1.05E+00 1.31 E-01 7.41 E-01 1.06E+00 1.23E-01 1.73E+00 1.05E+00 1.31 E-01 1.27E+00 1.05E+00 1.28E-01 9.13E-01 1.05E+00 1.31 E-01 1.01 E+00 1.06E+00 1.24E-01 2.36E+00 1.05E+00 1.32E-01 1.72E+00 1.05E+00 1.28E-01 1.22E+00 1.05E+00 1.31 E-01 1.28E+00 1.06E+00 1.24E-01 3.01EE+00 1.06E+00 1.34E-01 2.17E+00 1.05E+00 1.29E-01 1.54E+00 1.05E+00 1.31 E-01 1.55E+00 1.07E+00 1.24E-01 3.63E+00 1.06E+00 1.35E-01 2.61E+00 1.05E+00 1.29E-01 1.85E+00 1.05E+00 1.31 E-01 2.5 Hz Median AF Sigma ln(AF)1 Hz Median AF Sigma Wn(AFR 0.5 Hz Median AF Sigma Wn(AF)2.18E-02 8.90E-01 1.23E-01 1.27E-02 1.02E+00 9.81E-02 8.25E-03 1.10E+00 2.04E-01 7.05E-02 8.91E-01 1.23E-01 3.43E-02 1.01 E+00 9.82E-02 1.96E-02 1.10E+00 2.02E-01 1.18E-01 8.92E-01 1.22E-01 5.51E-02 1.01 E+00 9.82E-02 3.02E-02 1.10E+00 2.01E-01 2.12E-01 8.93E-01 1.22E-01 9.63E-02 1.01 E+00 9.82E-02 5.11E-02 1.09E+00 2.OOE-01 3.04E-01 8.93E-01 1.22E-01 1.36E-01 1.01 E+00 9.83E-02 7.10E-02 1.09E+00 2.OOE-01 3.94E-01 8.93E-01 1.22E-01 1.75E-01 1.01 E+00 9.83E-02 9.06E-02 1.09E+00 2.OOE-01 4.86E-01 8.93E-01 1.22E-01 2.14E-01 1.01 E+00 9.83E-02 1.10E-01 1.09E+00 2.OOE-01 7.09E-01 8.93E-01 1.22E-01 3.1OE-01 1.01 E+00 9.83E-02 1.58E-01 1.09E+00 2.0OE-01 9.47E-01 8.94E-01 1.22E-01 4.12E-01 1.01 E+00 9.83E-02 2.09E-01 1.09E+00 2.OOE-01 1.19E+00 8.94E-01 1.22E-01 5.18E-01 1.01 E+00 9.83E-02 2.62E-01 1.09E+00 2.OOE-01 1.43E+00 8.94E-01 1.22E-01 6.19E-01 1.01E+00 9.84E-02 3.12E-01 1.09E+00 2.O0E-01 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 31 Tables A2-bl and A2-b2 are tabular versions of the typical amplification factors provided in Figures 2.3.6-1 and 2.3.6-2. Values are provided for two input motion levels at approximately 1E-5 and 1E-5 mean annual frequency of exceedance.

These tables concentrate on the frequency range of 0.5 Hz to 25 Hz, with values up to 100 Hz included, and a single value at 0.1 Hz included for completeness.

These factors are unverified and are provided for information only. The figures should be considered the governing information.

McGuire Nuclear Station 32 Report Number: DUKCORP042-PR-002 Table A2-bl. Median AFs and sigmas for Model 1, Profile 1, for 2 PGA levels M1 P1 K1 Rock PGA=0.194 M1 P1 Kt PGA=0.741 Freq Soil SA Median Sigma Freq Soil SA Median Sigma (Hz) AF ln(AF) (Hz) AF In(AF)100.0 0.201 1.037 0.137 100.0 0.779 1.051 0.138 87.1 0.208 1.043 0.136 87.1 0.810 1.059 0.137 75.9 0.220 1.057 0.134 75.9 0.871 1.075 0.134 66.1 0.246 1.082 0.136 66.1 0.997 1.104 0.136 57.5 0.296 1.117 0.149 57.5 1.239 1.138 0.151 50.1 0.369 1.158 0.166 50.1 1.565 1.178 0.169 43.7 0.430 1.141 0.170 43.7 1.814 1.155 0.174 38.0 0.460 1.109 0.163 38.0 1.911 1.122 0.167 33.1 0.469 1.068 0.153 33.1 1.913 1.079 0.158 28.8 0.468 1.065 0.146 28.8 1.874 1.073 0.149 25.1 0.462 1.043 0.141 25.1 1.818 1.049 0.144 21.9 0.454 1.074 0.139 21.9 1.754 1.080 0.140 19.1 0.443 1.062 0.136 19.1 1.686 1.067 0.138 16.6 0.430 1.072 0.135 16.6 1.612 1.077 0.136 14.5 0.415 1.084 0.135 14.5 1.537 1.088 0.136 12.6 0.399 1.069 0.137 12.6 1.458 1.072 0.137 11.0 0.381 1.048 0.137 11.0 1.379 1.050 0.138 9.5 0.364 1.046 0.135 9.5 1.302 1.048 0.135 8.3 0.344 1.070 0.140 8.3 1.218 1.072 0.140 7.2 0.327 1.086 0.135 7.2 1.147 1.087 0.135 6.3 0.308 1.091 0.142 6.3 1.074 1.092 0.142 5.5 0.287 1.062 0.143 5.5 0.992 1.063 0.143 4.8 0.270 1.021 0.128 4.8 0.927 1.022 0.128 4.2 0.251 0.980 0.138 4.2 0.857 0.981 0.138 3.6 0.233 0.936 0.150 3.6 0.792 0.936 0.149 3.2 0.217 0.924 0.154 3.2 0.732 0.925 0.154 2.8 0.197 0.885 0.141 2.8 0.662 0.885 0.141 2.4 0.184 0.896 0.122 2.4 0.615 0.896 0.122 2.1 0.176 0.941 0.153 2.1 0.585 0.942 0.153 1.8 0.157 0.939 0.144 1.8 0.520 0.940 0.144 1.6 0.138 0.951 0.144 1.6 0.454 0.952 0.144 1.4 0.124 0.996 0.175 1.4 0.407 0.995 0.174 1.2 0.113 1.023 0.175 1.2 0.366 1.022 0.174 1.0 0.101 1.021 0.124 1.0 0.328 1.020 0.124 0.91 0.093 1.023 0.117 0.91 0.297 1.023 0.117 0.79 0.085 1.034 0.136 0.79 0.269 1.033 0.135 0.69 0.076 1.049 0.154 0.69 0.241 1.048 0.154 0.60 0.068 1.064 0.173 0.60 0.211 1.063 0.172 0.52 0.058 1.077 0.193 0.52 0.181 1.075 0.192 0.46 0.049 1.083 0.206 0.46 0.151 1.082 0.206 0.10 0.002 1.018 0.059 0.10 0.006 1.017 0.051 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 33 Table A2-b2. Median AFs and sigmas for Model 2, Profile 1, for 2 PGA levels M2P1 K1 PGA=0.194 M2P1K1 PGA=0.741 Freq Soil SA Median Sigma Freq Soil SA Median Sigma (Hz) AF ln(AF) (Hz) AF ln(AF)100.0 0.201 1.038 0.138 100.0 0.778 1.051 0.139 87.1 0.208 1.044 0.137 87.1 0.810 1.059 0.138 75.9 0.220 1.057 0.135 75.9 0.872 1.076 0.136 66.1 0.246 1.082 0.137 66.1 1.000 1.107 0.141 57.5 0.297 1.118 0.152 57.5 1.245 1.143 0.158 50.1 0.370 1.159 0.169 50.1 1.569 1.181 0.175 43.7 0.430 1.142 0.172 43.7 1.813 1.155 0.175 38.0 0.460 1.110 0.164 38.0 1.906 1.120 0.166 33.1 0.469 1.068 0.154 33.1 1.907 1.075 0.155 28.8 0.468 1.065 0.146 28.8 1.868 1.070 0.147 25.1 0.462 1.043 0.141 25.1 1.813 1.046 0.142 21.9 0.454 1.074 0.139 21.9 1.750 1.077 0.139 19.1 0.443 1.062 0.136 19.1 1.682 1.065 0.137 16.6 0.430 1.072 0.135 16.6 1.609 1.075 0.135 14.5 0.415 1.084 0.135 14.5 1.535 1.087 0.135 12.6 0.399 1.069 0.137 12.6 1.456 1.071 0.137 11.0 0.381 1.048 0.137 11.0 1.378 1.049 0.137 9.5 0.364 1.046 0.135 9.5 1.301 1.047 0.135 8.3 0.343 1.070 0.140 8.3 1.217 1.071 0.140 7.2 0.327 1.086 0.135 7.2 1.147 1.087 0.135 6.3 0.308 1.091 0.142 6.3 1.074 1.092 0.142 5.5 0.287 1.062 0.143 5.5 0.991 1.063 0.142 4.8 0.270 1.021 0.128 4.8 0.927 1.022 0.128 4.2 0.251 0.980 0.138 4.2 0.857 0.981 0.138 3.6 0.233 0.936 0.150 3.6 0.792 0.936 0.149 3.2 0.217 0.924 0.154 3.2 0.732 0.925 0.154 2.8 0.197 0.885 0.141 2.8 0.662 0.885 0.141 2.4 0.184 0.896 0.122 2.4 0.615 0.896 0.122 2.1 0.176 0.941 0.153 2.1 0.585 0.941 0.153 1.8 0.157 0.939 0.144 1.8 0.520 0.940 0.144 1.6 0.138 0.951 0.144 1.6 0.454 0.952 0.144 1.4 0.124 0.996 0.175 1.4 0.407 0.995 0.174 1.2 0.113 1.023 0.175 1.2 0.366 1.022 0.174 1.0 0.101 1.021 0.124 1.0 0.328 1.020 0.124 0.91 0.093 1.023 0.117 0.91 0.297 1.023 0.117 0.79 0.085 1.034 0.136 0.79 0.269 1.033 0.135 0.69 0.076 1.049 0.154 0.69 0.241 1.048 0.154 0.60 0.068 1.064 0.173 0.60 0.211 1.063 0.172 0.52 0.058 1.077 0.193 0.52 0.181 1.075 0.192 0.46 0.049 1.083 0.206 0.46 0.151 1.082 0.206 0.10 0.002 1.018 0.059 0.10 0.006 1.017 0.051 McGuire Nuclear Station Report Number: DUKCORP042-PR-002 34