ML062170007
ML062170007 | |
Person / Time | |
---|---|
Site: | Browns Ferry ![]() |
Issue date: | 09/27/2006 |
From: | Chernoff M NRC/NRR/ADRO/DORL/LPLII-2 |
To: | Singer K Tennessee Valley Authority |
Chernoff M, NRR/DORL, 415-4041 | |
Shared Package | |
ML062280009 | List: |
References | |
TAC MC1330 | |
Download: ML062170007 (26) | |
Text
September 27, 2006Mr. Karl W. SingerChief Nuclear Officer and Executive Vice President Tennessee Valley Authority 6A Lookout Place 1101 Market Street Chattanooga, TN 37402-2801
SUBJECT:
BROWN FERRY NUCLEAR PLANT, UNIT 1 - ISSUANCE OF AMENDMENTREGARDING POWER RANGE NEUTRON MONITOR UPGRADE (TAC NO.
MC1330) (TS-430)
Dear Mr. Singer:
The Commission has issued the enclosed Amendment No. 262 to Renewed Facility OperatingLicense No. DPR-33 for the Browns Ferry Nuclear Plant, Unit 1, in response to your application dated November 10, 2003, as supplemented by letter dated November 8, 2004. Thisamendment incorporates the necessary Technical Specification (TS) changes for the planned replacement of the power range monitoring portion of the existing Neutron Monitoring System with a digital upgrade. These changes expand the current allowable operating domain to the Maximum Extended Load Line Limit region of the core power/flow chart.The analyses used by the NRC staff in its review of the Maximum Extended Load Line LimitAnalysis (MELLLA) were performed at a power level of 3952 MWt (120 percent of current licensed thermal power (CLTP)). The Nuclear Regulatory Commission (NRC) staff finds thatthe MELLLA conditions would remain bounding up to CLTP. Approval of this amendment does not constitute authority to operate above the CLTP.By letter dated January 6, 2006, TVA submitted a proposed TS change involving the activationof thermal-hydraulic stability monitoring instrumentation. The proposed changes related to theactivation of this instrumentation contained in the above submittals will be addressed by theNRC staff in our review of the January 6, 2006, submittal, and are not approved in thisamendment.
K. Singer- 2 -A copy of the Safety Evaluation is also enclosed. Notice of Issuance will be included in theCommission's biweekly Federal Register notice.Sincerely,/RA/Margaret H. Chernoff, Project ManagerPlant Licensing Branch II-2 Division of Operating Reactor Licensing Office of Nuclear Reactor RegulationDocket No. 50-259
Enclosures:
- 1. Amendment No. 262 to License No. DPR-332. Safety Evaluationcc w/encls: See next page K. Singer- 2 -A copy of the Safety Evaluation is also enclosed. Notice of Issuance will be included in theCommission's biweekly Federal Register notice.Sincerely,/RA/Margaret H. Chernoff, Project ManagerPlant Licensing Branch II-2 Division of Operating Reactor Licensing Office of Nuclear Reactor RegulationDocket No. 50-259
Enclosures:
- 1. Amendment No. 262 to License No. DPR-332. Safety Evaluationcc w/encls: See next pageDISTRIBUTION
- PUBLICRidsNrrDssSbwbRidsRgn2MailCenter(MWidmann,LMellen)LPL2-2 R/FRidsNrrDorlDprRidsNrrLABClayton (Hard Copy)
RidsNrrDorlRidsNrrDeEicbRidsOgcRp RidsNrrLACGoldsteinRidsNrrDirsItsbGThomas RidsAcrsAcnwMailCenterRidsNrrPMEBrownDDuvigneaud RidsNrrDorlLpl2-2 (LRaghavan)RidsNrrPMMChernoffMWaterman AMunizPackage No.:ML062280009TS: ML062750565ADAMS ACCESSION NO.: ML062170007NRR-058OFFICELPL3-1\PELPL2-2\PELPL2-2\PMLPL2-2\LAEICB/SCNAMEAMunizDDuvigneaudMChernoffBClaytonEMarinos DATE9/27/069/27/069/27/069/22/064/30/2004OFFICESBWB/BCITSB/BC*OGC - NLOLPL2-2\BCNAMEGCranstonTKobetzMZoblerLRaghavanDATE9/1/20069/26/069/25/069/27/06*with commentsOFFICIAL RECORD COPY TENNESSEE VALLEY AUTHORITYDOCKET NO. 50-259BROWNS FERRY NUCLEAR PLANT UNIT 1AMENDMENT TO RENEWED FACILITY OPERATING LICENSEAmendment No. 262 Renewed License No. DPR-331.The Nuclear Regulatory Commission (the Commission) has found that:A.The application for amendment by Tennessee Valley Authority (the licensee)dated November 10, 2003, as supplemented November 8, 2004, complies with the standards and requirements of the Atomic Energy Act of 1954, as amended (the Act), and the Commission's rules and regulations set forth in 10 CFR Chapter I;B.The facility will operate in conformity with the application, the provisions of theAct, and the rules and regulations of the Commission;C.There is reasonable assurance (i) that the activities authorized by thisamendment can be conducted without endangering the health and safety of the public, and (ii) that such activities will be conducted in compliance with theCommission's regulations;D.The issuance of this amendment will not be inimical to the common defense andsecurity or to the health and safety of the public; andE.The issuance of this amendment is in accordance with 10 CFR Part 51 of theCommission's regulations and all applicable requirements have been satisfied. 2.Accordingly, the license is amended by changes to the Technical Specifications asindicated in the attachment to this license amendment and paragraph 2.C.(2) of Renewed Facility Operating License No. DPR-33 is hereby amended to read as follows:(2)Technical SpecificationsThe Technical Specifications contained in Appendices A and B, as revised throughAmendment No. 262, are hereby incorporated in the license. The licensee shall operate the facility in accordance with the Technical Specifications.3.This license amendment is effective as of its date of issuance and shall be implementedwithin 30 days from the date of issuance. FOR THE NUCLEAR REGULATORY COMMISSION/RA/ L. Raghavan, Chief Plant Licensing Branch II-2 Division of Operating Reactor Licensing Office of Nuclear Reactor Regulation
Attachment:
Changes to the Technical SpecificationsDate of Issuance: September 27, 2006 ATTACHMENT TO LICENSE AMENDMENT NO. 262RENEWED FACILITY OPERATING LICENSE NO. DPR-33DOCKET NO. 50-259Replace Page 3 of Renewed Operating License DPR-33 with the attached Page 3.Revise the Appendix A Technical Specifications by removing the pages identified below andinserting the attached pages. The revised pages are identified by the captioned amendment number and contain marginal lines indicating the area of change. REMOVEINSERT ii1.1-51.1-5 3.2-7---
3.2-8---
3.3-13.3-1 3.3-23.3-2 3.3-33.3-3 3.3-43.3-4 3.3-53.3-5 3.3-63.3-6 3.3-73.3-7 3.3-183.3-18 3.3-193.3-19 3.3-203.3-20 3.10-223.10-22 3.10-243.10-24 SAFETY EVALUATION BY THE OFFICE OF NUCLEAR REACTOR REGULATION RELATED TO AMENDMENT NO. 262 TO RENEWED FACILITY OPERATING LICENSE NO. DPR-33TENNESSEE VALLEY AUTHORITYBROWNS FERRY NUCLEAR PLANT, UNIT 1DOCKET NO. 50-25
91.0 INTRODUCTION
By letter dated November 10, 2003 (Agencywide Documents Access and Management System(ADAMS) Number ML03300129), as supplemented by letter dated November 8, 2004 (ADAMS ML043130366), the Tennessee Valley Authority (TVA, the licensee) submitted a request for changes to the Browns Ferry Nuclear Plant (BFN), Unit 1, Technical Specifications (TSs). The application addresses design changes that would upgrade the analog power monitoring systemin BFN Unit 1 with a General Electric Company (GE) Nuclear Measurement Analysis and Control Power Range Neutron Monitor System (NUMAC-PRNMS), including an OscillationPower Range Monitoring (OPRM) function. It also proposes the implementation of the Average Power Range Monitor, Rod Block Monitor (RBM) TS improvements and operation in an expanded core power/flow domain, the Maximum Extended Load Line Limit Analysis (ARTS/MELLLA) region. The supplement dated November 8, 2004, provided additionalinformation that clarified the application, did not expand the scope of the application asoriginally noticed, and did not change the staff's original proposed no significant hazards consideration determination as published in the Federal Register on February 3, 2004 (69 FR5208).By letter dated January 6, 2006, TVA submitted a proposed TS change involving the activationof thermal-hydraulic stability monitoring instrumentation. The proposed changes related to theactivation of the instrumentation contained in this application will be addressed by the NuclearRegulatory Commission (NRC) staff in its review of the January 6, 2006, submittal, and are notapproved in this amendment.2.0EVALUATION2.1Description of ChangeBFN Unit 1 is a boiling-water reactor (BWR) 4 type reactor with a 251-inch diameter vessel andMark I containment. The current licensed thermal power (CLTP) is 3293 megawatts-thermal.
BFN Unit 1 is currently licensed and analyzed for increased core flow operation at 102.5 millionpounds-mass per hour. The proposed change expands the current allowable operating domain to the Maximum Extended Load Line Limit region of the core power/flow chart. The currently analyzed limiting power/flow point for Single Loop Operation (SLO) will not change for theproposed MELLLA implementation since SLO is not extended into the MELLLA operatingregion.The operational flexibility of a BWR during power ascension from the low-power, low-flow corecondition to the rated high-power, high-flow core condition is restricted by several factors. Also, once rated power is achieved, periodic adjustments to core flow and control rod positions must be made to compensate for the reactivity changes due to Xenon buildup and decay, with fuel and burnable poison burnup. Factors currently restricting plant flexibility at BFN Unit 1 inefficiently achieving and maintaining rated power include: 1)the currently licensed allowable power/flow operating map; and, 2)the current Average Power Range Monitor (APRM) flow-biased flux scram andflow-biased rod block setdown requirements. The licensee
<s proposed TS amendments applicable to the APRM portion of the BFN Unit 1TSs are to be implemented following the replacement of the existing power range portion of the existing Neutron Monitoring System with a GE NUMAC-PRNMS, including the Option III OPRM function. The planned modification involves replacing the existing six APRM channels of power range monitor electronics with four channels of NUMAC-PRNMS hardware. The existing equipment is located in a five-bay panel in the main control room. The modification will removeand replace the existing power range monitor equipment within the panels but, with minor exceptions, leave the plant cabling and interfaces undisturbed. All power range monitoring functions will be maintained in the new system, including the LocalPower Range Monitor (LPRM) detector signal processing, LPRM averaging, APRM reactor trips, and RBM logic and interlocks. The LPRM input signals to the APRMs will be reconfiguredsuch that each of the four new APRM channels will be allocated one-fourth of the existingLPRM signals.The NUMAC-PRNMS consists of four APRM channels and four voter channels. Trip signalsfrom each of the four APRM channels are sent to all four voter channels. One voter module is dedicated to each reactor protection system (RPS) trip relay. A reactor trip occurs when two ormore of the four APRM functions or two or more of the four OPRM functions calculate a trip condition. The voters perform a vote of the OPRM channel trip outputs separate from the APRM trip outputs (i.e., an OPRM trip in one channel and an APRM trip in another channel willnot result in a reactor trip from two of four voters in a trip state).As part of the planned modification, the number of APRM instrument channels will be reducedfrom six channels to four channels. The LPRM inputs to the APRMs will also be reconfigured. The four APRM instrument channels will be combined in four 2-out-of-4 trip logic channels,which will provide input to the RPS trip channels. The number of recirculation flow instrument channels associated with the APRMs will beincreased from two total flow channels (four transmitters) to four total flow channels (eight transmitters). The recirculation flow signal processing, which was previously accomplished using separate hardware within the power range monitor control panels, will be integrated intothe APRM chassis in the new PRNMS. 2.2Regulatory EvaluationTitle 10 of the Code of Federal Regulations (10 CFR) Section 50.36, "Technical specifications,"which provides the regulatory requirements for the content required in a licensee's TSs. Asstated in 10 CFR 50.36, the TSs will include Surveillance Requirements (SRs) to assure thatthe limiting conditions for operation (LCO) will be met. The proposed TS changes would reviseSRs and the LCO actions and completion times for each applicable operating condition.10 CFR 50.62, "Requirements for reduction of risk from anticipated transients without scram(ATWS) events for light-water-cooled nuclear power plants," contains the regulatoryrequirements governing the ATWS. This regulation includes requirements for an ATWS Recirculation Pump Trip (RPT), an Alternate Rod Insertion system, and an adequate StandbyLiquid Control System injection rate.10 CFR 50.46, "Acceptance criteria for emergency core cooling systems (ECCS) for light-waternuclear power reactors," provides acceptance criteria for ECCS cooling performance following postulated loss-of-coolant accidents (LOCAs).At the time BFN was licensed, 10 CFR 50 Appendix A, "General Design Criteria (GDC) forNuclear Power Plants," was not incorporated in the NRC regulations. BFN conformed to thedraft Proposed GDC 27 (Units 1 and 2) and draft 70 (unit 3) criteria current at the time of the BFN design. The design bases of each unit of this plant were reevaluated against the draft 70 criteria current at the time of operating license application. It was concluded that each unit ofthis plant conforms with the intent of the GDC for Nuclear Power Plant Construction Permits.
The references to the criteria below refer to these proposed GDC, not the GDC in Appendix Aof 10 CFR 50.Criterion 6, "Reactor core design," states that the reactor core shall be designed to functionthroughout its design lifetime, without exceeding acceptable fuel damage limits which have been stipulated and justified. The core design, together with reliable process and decay heat removal systems, shall provide for this capability under all expected conditions of normaloperation with appropriate margins for uncertainties and for transient situations which can be anticipated, including the effects of the loss of power to recirculation pumps, tripping out of aturbine generator set, isolation of the reactor from its primary heat sink, and loss of all offsite power.Criterion 7, "Suppression of power oscillations," states that the core design, together withreliable controls, shall ensure that power oscillations which could cause damage in excess ofacceptable fuel damage limits are not possible or can be readily suppressed.Criterion 40, "Missile Protection," states that protection for engineered safety features shall beprovided against dynamic effects and missiles that might result from plant equipment failures.Criterion 42, "Engineered safety features performance capability," states that engineered safetyfeatures shall be designed so that the capability of each com ponent and system to perform itsrequired function is not impaired by the effects of a loss-of-coolant accident.NUREG-0800, "Standard review plan for the review of safety analyses reports for nuclearpower plants," provides guidance to NRC staff reviewers in the Office of Nuclear Reactor Regulation in performing safety reviews of applications to construct or operate nuclear powerplants and the review of applications to approve standard designs and sites for nuclear power plants.Under certain conditions, BWRs may be susceptible to coupled neutronic/thermal-hydraulicinstabilities. These instabilities are characterized by periodic power and flow oscillations. Ifthese power and flow oscillations become large enough, the fuel cladding integrity minimumcritical power ratio (MCPR) safety limit requirements may be challenged.To detect core instabilities automatically and provide a reactor scram signal to the RPS, thelicensee selected Boiling-Water Reactor Owners Group (BWROG) Stability Option III as thelong-term stability system solution (LTSSS) for BFN Unit 1. The LTSSS Option III approachconsists of detecting and suppressing stability-related power oscillations by automaticallyinserting control rods (scramming) to terminate power oscillations, consistent with proposedGDC criterion 6 and criterion 7.The GE NUMAC-PRNMS design was approved by the NRC staff in its safety evaluation (SE) ofGE Licensing Topical Report (LTR) NEDC-32410P-A, "Nuclear Measurement Analysis and Control Power Range Neutron Monitor (NUMAC-PRNM) Retrofit Plus Option III Stability TripFunction," dated September 5, 1995. The SE was subsequently included in the approvedversion of the LTR (ADAMS ML9605290009). Supplement 1 of the LTR was approved by the NRC staff in its SE dated August 15, 1997. The SE was subsequently included in the approvedSupplement 1 of the LTR (ADAMS ML9806120242). The LTR and Supplement 1 address the BWR power instability issue discussed in GE LTR NEDO-31960, "BWR Owners' GroupLong-Term Stability Solutions Licensing Methodology" (ADAMS ML9106100443).The NRC staff approved use of the NUMAC-PRNMS with the OPRM functions in BWR designplants. The NUMAC-PRNMS with the Option III LTSSS function, when installed and operatedin accordance with the approved guidance provided in the above-referenced licensing topical reports, is consistent with proposed GDC criterion 6 and criterion 7.
3.0TECHNICAL EVALUATION
The licensee's submittal contained two groups of requested TS changes. The changesidentified as Group 1 are related to the proposed APRM and RBM TS (ARTS) improvements as a result of the NUMAC-PRNMS modification. The changes identified as Group 2 are related to concurrent implementation of improvements related to operations in the core power/flowdomain, the MELLLA region. Information provided by TVA as part of the Extended Power Uprate (EPU) application dated June 28, 2004, related to the MELLLA was used in support of this review. The NRC staff finds this approach acceptable because MELLLA conditions at EPUbound the MELLLA conditions at CLTP. Approval of this amendment does not constitute authority to operate above the CLTP.3.1.1NUMAC-PRNMS Modification The APRM system averages LPRM signals, processes flow signals from the reactor corerecirculation flow instrumentation, and then compares the results to RPS trip set points. The OPRM detects and suppresses reactor core power instabilities using the Option III approachdescribed in LTR NEDO-31960. As stated in the NRC staff's SE of NEDC-32410P-A, to receive NRC approval of aNUMAC-PRNMS installation, the licensee must confirm the following:1.The applicability of NEDC-32410P, including clarifications and reconciled differencesbetween the specific plant design and the topical report design descriptions.2.The applicability of the BWROG topical reports that address the NUMAC-PRNMS andassociated instability functions, setpoints and margins.3.Plant-specific revised TSs for the NUMAC-PRNMS functions are consistent withNEDC-32410P, Appendix H, and Supplement 1.4.Plant-specific environmental conditions are enveloped by the NUMAC-PRNMSequipment environmental qualification values.5.Administrative controls are provided for manually bypassing APRM/OPRM channels orprotective functions, and for controlling access to the APRM/OPRM panel and channelbypass switch.6.Any changes to the plant operator's panel have received human factors reviews perplant-specific procedures.The licensee's actions with regard to the above conditions are discussed in the followingsections.3.1.1.1Applicability of the NUMAC-PRNMS Design to the BFN Unit 1 Plant Design The NRC staff compared the applicable BFN Unit 1 design features with the correspondingdesign features in LTR NEDC-32410P-A. BFN Unit 1 is a GE BWR/4, a BWR design addressed in the LTR. As stated in Section 2 above, the six APRM channels currently used in BFN Unit 1 will be combined into four 2-out-of-4 logic channels that will provide inputs throughdedicated RPS channel voters to the four RPS channels. The licensee is increasing the number of recirculation flow instrument channels from two total flow channels (four transmitters) to four channels (eight transmitters). These proposed design modifications conform to the NUMAC-PRNMS design description in NEDC-32410P-A, and are compatible with the existing plant neutron monitoring system and RPS. Therefore, the NRC staff finds that theNUMAC-PRNMS design is applicable to BFN Unit 1.3.1.1.2PRNMS OPRM Instability Function Set Points, and MarginsThe licensee will test the PRNMS instability function (OPRM), including the adequacy of the setpoint values and margins during the first fuel cycle of OPRM operation, using themethodology described in LTR NEDO-32465-A, "BWR Owners' Group Reactor Stability Detectand Suppress Solutions Licensing Basis Methodology and Reload Applications," dated August 1996 (ADAMS ML9609230137). The NRC staff approved the initial period for OPRM confirmatory testing in the SE of NEDC-32410P-A and, therefore, finds the licensee's approachfor developing OPRM set points and margins acceptable.3.1.1.3Plant-specific TSs See Section 3.1.3 for a discussion of the plant-specific revised TSs.
3.1.1.4 Plant-Specific Environmental Conditions In Table 1, the BFN plant-specific environmental conditions for temperature, humidity, pressure,and radiation are compared to the NUMAC-PRNMS environmental qualification values.Table 1. Comparison of BFN Unit 1 Environmental Conditions with NUMAC-PRNMEnvironment Qualification ValuesBFN Unit 1NUMAC-PRNMSTemperature15.6C to 40C(60 F to 104F)5C to 50C(41F to 122F)Humidity10% to 90% RH [relative humidity]10% to 90% RH Pressure14.7 psia [pounds per square inch-absolute] to 14.72 psia13 psia to 16 psiaRadiation1E-3 Rads/hr dose rate350 Rads TID [total integrated dose]1E-3 Rads/hr dose rate1E+3 Rads TIDAs shown in Table 1, the BFN environmental conditions are enveloped by the NUMAC-PRNMSqualification values, and, therefore, are acceptable.The NRC staff reviewed the seismic response spectra for the BFN units and concludes that theBFN Unit 1 seismic qualification is within the NUMAC-PRNMS seismic qualification envelope, and, therefore, is acceptable.GE Licensing Topical Report NEDC-32410P-A states that new equipment and plantmodifications should not produce unacceptable levels of noise emissions that could adversely affect NUMAC equipment, or the licensee is to take action to prevent these emissions from reaching potentially sensitive equipment. These measures apply for both noise susceptibilityand emissions. The BFN design procedures require that all digital equipment systems installedor used within the plant be evaluated for susceptibility and emissions of electromagneticinterference (EMI) in accordance with the NRC approved Electric Power Research InstituteGuideline TR-102323. The NRC staff finds this approach acceptable for ensuring the EMIenvironment conforms to the guidance of proposed GDC criterion 40 and criterion 42. The NRC staff reviewed the licensee's evaluation of environmental conditions in BFN Unit 1 andconcludes that the BFN Unit 1 environmental conditions are enveloped by the GE equipment qualification parameters established for the NUMAC-PRNMS modification. As described in NEDC-32410P-A, the PRNMS uses the same panel interfaces as the existing power range monitor equipment. High frequency filters are installed on the ac power supply, and shielded cables for all signal leads will be used in lieu of testing nonsafety equipment noiseeffects on the PRNMS.The NRC staff finds the licensee's evaluation of the EMI environment and the measures takento reduce adverse EMI affects to be an acceptable approach for ensuring the NUMAC-PRNMS EMI environment conforms to the guidance of proposed GDC criterion 40 and criterion 42 for protection against adverse environmental effects.3.1.1.5Administrative controls In the SE of NEDC-32410P-A, the NRC staff found the NUMAC-PRNMS design features thatcontrol access to setpoint adjustments, calibrations, and test points acceptable. Since the licensee has not proposed design changes that would override these controls, the NRC stafffinds that the licensee has acceptable controls for controlling access to the PRNMS panel andthe APRM/OPRM channel bypass switch.3.1.1.6Confirmation of Human Factors Review The licensee stated that the BFN Unit 1 design change process and implementing proceduresrequire completion of a Human Factors Engineering (HFE) Process Checklist and performance of an HFE review of changes to the plant operator's panel. The licensee further stated that an HFE review, per applicable BFN Unit 1 procedures of the proposed changes to the operator's panel, will be performed, and documentation of that review will be included in the final designpackage(s) for the PRNMS. The NRC staff performed a control room design review as part ofthe BFN Unit 1 restart recovery efforts. The NRC staff selected a sample of high safety significant and verified that the licensee had developed modification design packages or other appropriate measures. No significant issues were identified. Therefore, based on the above and that the licensee previously performed these changes to Units 2 and 3 with no major challenges, the NRC staff finds this acceptable. On the basis of the above review and justifications for TS changes, the NRC staff concl udesthat the licensee's proposed TS changes for BFN Unit 1 are consistent with the NRCstaff-approved guidance in NEDC-32410P-A. The NRC staff further concludes that thelicensee has properly addressed the plant-specific conditions described in the NRC staff's SEfor NEDC-32410P-A, and, therefore, finds the NUMAC-PRNMS modification and associated TS changes to be acceptable.3.1.2ARTS/MELLLA Implementation The function of the licensed allowable power/flow operating map is to define the normaloperating condition of the reactor core used in determining the operating safety limits. The proposed TS change reflects operation of BFN Unit 1 in a region that is above the current rated rod line. The current approved operating envelope is modified to include the extended operating region bounded by the rod line that passes through the 100-percent power/99-percentcore flow point shown in Figure 2-1 of Ref. 1. This extended operating domain is called the MELLLA. The analysis presented in Ref. 1 includes the MELLLA conditions and the equilibriumanalysis performed for GE-14 fuel. The function of the RBM is to prevent fuel damage in the event of erroneous rod withdrawalfrom locations of high-power density during high-power level operation. It does this by blocking control rod movement that could result in violating a thermal limit (the safety limit MCPR or the 1-percent cladding plastic strain limit) in the event of a Rod Withdrawal Error (RWE) event. The functions of the APRM system include:generation of a trip signal to scram the reactor during core-wide neutron flux transientsbefore exceeding the safety analysis design basis, blocking control rod withdrawal whenever operation exceeds set limits in the operatingmap, prior to approaching the scram level, and, providing an indication of the core average power level in the power range. The flow-biased rod block setdown and APRM flow-biased flux scram trip and alarm functionsare provided to achieve these requirements. The proposed partial implementation of the APRM, RBM Technical Specification (ARTS)improvement program will increase the plant operating efficiency by updating the thermal limitsrequirements to be consistent with current GE methodology and from improvements in plantinstrumentation accuracy and response by incorporating digital flow control trip reference (FCTR) cards to replace the original analog cards. The ARTS improvement program includes changes to the current APRM system, whichrequires the TS changes described in Section 3.11 below. The current BFN Unit 1 improved TSs require that the flow-referenced APRM scram and rod block trips be lowered (setdown) when the core Maximum Total Peaking Factor exceeds the design Total Peaking Factor. An alternative to an actual "setdown" is accomplished by adjusting the APRM gain upwards to achieve the desired equivalent result. The basis for the current APRM trip setdown requirement corresponds to the Hench-Levy Minimum Critical Heat Flux Ratio thermal limit criteria (Ref. 3).
A subsequent update to the thermal limits requirements, which decreases the dependence onthe local thermal hydraulic conditions, including the core peaking factors, was developed by GE. The resulting GE Thermal Analysis Basis critical power ratio correlation model (Ref. 3),
which relies on bundle boiling length and exit quality, was reviewed and approved by the NRCstaff. The objective of the APRM improvements is to justify removal of the APRM trip setdown andthe Design Total Peaking Factor requirement. Since the elimination of the APRM gain and setpoint requirement can potentially affect the fuel thermal-mechanical integrity and the ECCSLOCA performance, the NRC staff reviewed the acceptability of these changes. The followingcriteria, contained in NUREG-0800, Chapters 4 and 15, were used by the NRC staff to assuresatisfaction of the applicable licensing requirements to demonstrate acceptability of the APRMtrip setdown requirement: 1)The safety limit minimum critical power ratio (SLMCPR) shall not be violated as aresult of any anticipated operational occurrences (AOOs), 2)All fuel thermal-mechanical design bases shall remain within the licensing limitsdescribed in the GE generic fuel licensing report (GESTAR-II), and, 3)The peak cladding temperature and the maximum cladding oxidation fractionfollowing a LOCA shall remain within the limits defined in 10 CFR 50.46. The ARTS-specific changes are summarized here: 1.The requirement for setdown of the APRM scrams and rod blocks is del eted, 2.New power-dependent MCPR adjustment factors, MCPR(p), are added, 3.New flow-dependent MCPR adjustment factors, MCPR(f), replace the K f multiplier, 4.New power-dependent and flow dependent maximum average planar linear heatgeneration rate (MAPLHGR) and, 5.The affected TS SRs, LCOs, and the associated Bases are modified or deleted, asrequired. The NRC staff reviewed the safety analyses and systems re sponse evaluations performed byGeneral Electric Nuclear Energy (GENE) to justify BFN Unit 1 operation in the expanded MELLLA region, as submitted in Refs. 1 and 2. The GE-14 equilibrium analyses presented inRef. 1 was specifically for Unit 1. However, the analysis presented in Ref. 2 was for all three units. The common analyses for BFN units fuel independent evaluations, such as containment response, were performed based on the current hardware design and applicable plant geometry for BFN Unit 1.3.1.2.1Method of Analysis The analyses that are used to justify operation with the ARTS improvement and the MELLLApower/flow operating map are based on NRC-approved computer codes, methodologies, andapplicable industry standards, which are discussed in the ARTS/MELLLA safety analysis report (A/MSAR) and associated references. Section 12 of Ref. 2 lists the nuclear steam supply system (NSSS) computer codes used in the safety analyses.The ARTS thermal limits are expected to be fuel cycle-independent and the ARTS transientanalyses in Ref. 2 were performed at the CLTP plant conditions for Unit 2 core configuration, using the GENE standard reload licensing methodology described in the GE Standard Application for Reactor Fuel, Rev. 14, dated June 2000 documentation. The BFN Unit 1plant-specific evaluations will be performed to establish plant-unique, flow-dependent MCPR,LHGR, and MAPLHGR limits.The NRC staff finds the methods used to be acceptable, since approved methods are used andthe example calculations provided demonstrate the application of the methods to the proposedARTS/MELLLA implementation at the CLTP condition. 3.1.2.2Fuel Thermal Limits The NRC staff reviewed the effects of operation along the higher MELLLA rod line at the CLTPon the thermal limits and the thermal limits management with the ARTS power and flowdependent limits, which are covered in the A/MSAR. The potentially limiting AOOs and accident analyses were evaluated to support BFN Unit 1 EPUoperation (with the ARTS off-rated limits, as well as operation in the MELLLA region for the reference equilibrium core of GE 14 ( Table 9-2 of Ref. 1). The NRC staff approved evaluationmethods presented in Ref. 8 were used for the transient analysis. The following events were evaluated:1.Generator Load Rejection with Bypass Failure; 2.Turbine Trip With Bypass Failure 3.Feedwater Controller Failure (FWCF) Maximum Demand 4.Feedwater Controller Failure with Turbine Bypass Out of Service (TBOOS) 5.Pressure Regulator Downscale Failure 6.Loss of Feedwater Heating 7.Inadvertent High Pressure Coolant Injection actuation 8.Rod Withdrawal Error 9.Slow Recirculation Increase 10.Fast Recirculation Increase 11.Generator Load Rejection with Bypass 12.Main Steam Isolation Valve (MSIV) Closure-All Valves 13.MSIV Closure-One Valve 14.Loss of Feedwater Flow 15.Loss of One Feedwater Pump The most limiting transients are the following:
Generator Load Rejection with Bypass Failure Turbine Trip With Bypass Failure FWCF Maximum Demand Feedwater Controller Failure maximum demand with TBOOSExtensive transient analyses at a variety of power and flow conditions, performed for theoriginal ARTS improvement program, established a database of limiting transients, which were representative of a variety of plant configurations and key parameters designed to be applicableto all BWRs. These generic evaluations determined power-dependent trends for two operating ranges. The first range is between the 100-percent rated thermal power and the power level[30 percent of CLTP for BFN Unit 1] where the reactor scram on turbine stop valve closure or turbine control valve fast closure is bypassed (Pbypass). The second range is from Pbypass (30 percent) down to 25 percent of the CLTP. The current BFN Unit 1 TS does not require thermal limit monitoring below 25 percent of CLTP. BFN Unit 1 specific analyses will be performed to confirm the applicability of the genericpower-dependent limit multipliers [K(p), and MAPLHGR(p)] above Pbypass. BFN Unit 1 specific evaluations will also be performed between Pbypass (30 percent) and 25-percentpower to establish BFN Unit 1 unique MCPR, LHGR, and MAPLHGR limits, which will apply tofuture reloads of GE fuel designs through the GE 14 design. BFN Unit 1 specific evaluations will also be performed to establish the flow-dependent MCPR and MAPLHGR limits. The MELLLA operating conditions have only a small effect on the operating limit maximumcritical power ratio (OLMCPR). The OLMCPR is calculated by adding the change in MCPR due to the limiting AOO event to the SLMCPR and will be determined with the actual core analysis before start-up. Analyses were performed for BFN Unit 1 before startup and beyond to providea BFN Unit 1 plant-specific, statistically-based, power-dependent RWE OLMCPR value. The cycle-specific reload fuel analyses will determine the limits for rated and applicable off-rated conditions, and application of the methodology is demonstrated by the analyses performed for the EPU operating cycle. Therefore, the NRC staff finds this approachacceptable.3.1.2.3Vessel Overpressure Protection The MSIV closure with a flux scram event is used to determine compliance to the industrystandard American Society of Mechanical Engineers Pressure Vessel Code. A plant-specific calculation was performed for a representative core at 102 percent of EPU power level (Ref. 1).
The peak calculated pressure for the limiting event was 1314 pounds per square inch gage (psig) less than the accepted criterion of 1375 psig and, hence, is acceptable. NRC staffapproved evaluation model Ref. 8 was used for the analyses.Because the licensee will perform cycle specific overpressure evaluations before start-up, usingapproved methods, the NRC staff finds this acceptable.3.1.2.4Thermal-Hydraulic Stability This change will be addressed in the NRC staff review of the January 6, 2006, submittal, andare not approved in this amendment.3.1.2.5LOCA Analysis The ECCS is designed to provide protection against postulated LOCAs caused by ruptures inthe primary system piping. The ECCS performance under all LOCA conditi ons and the analysismodels must satisfy the requirements of 10 CFR 50.46 and 10 CFR Part 50, Appendix K. The MAPLHGR operating limit is based on the most limiting LOCA and ensures compliance with the ECCS acceptance criteria in 10 CFR 50.46. For most BWRs, the full-spectrum ECCS-LOCA analyses were performed when the plantsconverted to the SAFER/GESTR analysis. For BFN Unit 1, this equilibrium analysis (Ref. 1)was performed based on operation along the current ELLLA rod line up 120 percent to the original licensed thermal power. The current basis also specifies the APRM setdown requirement of a maximum LHGR value asa function of drive flow. This requirement is proposed to be replaced with the direct core power and flow dependent fuel thermal limits of the ARTS improvement program, which is not required for the LOCA analysis. The NRC staff reviewed the current licensing basis analysis todetermine the ECCS performance effect of operation in the MELLLA domain. An evaluationwas performed with GE 14 and GE 13 fuel to demonstrate compliance with the ECCS-LOCA acceptance criteria. The NRC staff approved evaluation methods for GE Reports NEDC-32484P, NEDE-23785P-A,and NEDO-20566A (Refs. 4, 5, and 6) that were used for the LOCA analyses. For MELLLA/EPU operation, a large break peak cladding temperature (PCT) value of 1830 Fwas determined for GE 14 fuel and 1780 F for GE 13 fuel. This provides an adequate margin to the 2200 F PCT limit. Justification for the elimination of the former 1600 F Upper BoundPCT limit was provided in the GE 14 BFN Unit 1 analysis. Also, the maximum local oxidation is less than 3 percent, and the core-wide metal-water reaction is less than 0.1 percent. Because the licensee performed a representative ECCS-LOCA analysis using 10 CFR 50.46 and Appendix K requirements, MELLLA operation is acceptable.The NRC staff has determined that no additional operating restrictions would be required forARTS/MELLLA operation, since the determination of the sensitivity of the ECCS-LOCAevaluations to operation in the MELLLA domain shows compliance with the acceptance criteria. 3.1.2.6Anticipated Transient without Scram (ATWS)
The NRC staff reviewed the BFN Unit 1 representative analysis that was performed using theapproved licensing methodology (Ref. 1) to demonstrate compliance with 10 CFR 50.62 ATWS requirements. The analysis has been performed for EPU RTP. The loss of off-site power and inadvertent opening of a relief valve events were determined to be nonlimiting.The NRC staff concludes, based on its review of the ATWS analyses described above, thatBFN Unit 1 meets the ATWS mitigating features stipulated in 10 CFR 50.62 and that the resultsof the ATWS analyses for MELLLA operation at the EPU RTP meet the ATWS acceptancecriteria. This approach is acceptable because the ATWS analyses at EPU RTP bound the ATWS analyses at CLTP. 3.1.2.7Testing Standard pre-operational testing (APRM, recirculation flow calibrations) will be performed afterinstallation of the new digital FCTR cards. The APRMs will be calibrated prior to ME LLLAimplementation. The APRM flow-biased scram and rod block setpoints will be consistent withthe ARTS/MELLLA implementation, with all APRM trips and alarms tested. The flow-biased setpoints for the RBM will be confirmed. The NRC staff finds this acceptable. The NRC staff has reviewed the licensee's license amendment request application along withthe supporting documentation, including responses from the request for additional information. The review of TS changes in this SE is performed solely to evaluate the changes that would berequired to support the ARTS/MELLLA implementation at BFN Unit 1. This review covered the ARTS/MELLLA application with a representative GE 14 analysis at EPU. Currently, Unit 1 is defueled and is scheduled to restart in 2007. TVA stated that the fuel supplier for Unit 1 will beGNF/GE. The bases for acceptance of MELLLA operation are approved GE evaluation methods and the use of only GE fuel for Unit 1. Information provided by TVA as part of the EPU application dated June 28, 2004, related to theMELLLA was used in support of this review. The NRC staff finds this approach acceptablebecause MELLLA conditions at EPU bound the MELLLA conditions at CLTP. Approval of this amendment does not constitute authority to operate above the CLTP. Based on its review, the NRC staff concludes that the proposed TS changes are acceptablebecause the safety analysis supporting actual operation in the ARTS/MELLLA regimes have been reviewed and the NRC staff concludes that operation will not endanger the public healthand safety. 3.1.3Plant-Specific Revised TSs The NRC staff reviewed the proposed changes to the BFN Unit 1 TSs that are identified in thelicensee's submittal. The NRC staff review was focused on MELLLA operation and not the EPUoperation. The approval of these TS sections are only for MELLLA conditions and not for EPU.
The changes include deletion of the current setdown requirement, and new power and flow-dependent MCPR and MAPLHGR limits. The proposed TS changes are as follows: 3.1.3.1Change 1 - Page I, Table of Contents The Table of Contents listing of Section 3.2.4, APRM Gain and Setpoints, has been deleted. This is a conforming editorial change related to change 3, discussed below. Therefore, the NRC staff finds this change acceptable.3.1.3.2Change 2 - Page 1.1-5, Section 1.1The definition of "Maximum Fraction" of limiting power density (MFLPD) is deleted. Thedefinition of MFLPD is no longer required in the TSs due to the ARTS/MELLLA implementation.
Therefore, the NRC staff finds this change acceptable.3.1.3.3Change 3 - Pages 3.2-7 and 3.2-8, Section 3.2.4 Section 3.2.4, the LCO and SR entitled "Average Power Range Monitor (APRM) Gain andSetpoints," is deleted in its entirety. Section 3.2.4 is no longer required in the TSs due to theARTS/MELLLA implementation. Therefore, the NRC staff finds this change acceptable.3.1.3.4Change 4 - Table 3.3.1.1-1, Reactor Protection System InstrumentationIn Change 4, the licensee proposed adding a Note for Required Action A.2 and for Condition B. The Note states, "Not applicable for Functions 2.a, 2.b, 2.c or 2.d." The licensee stated thatneither Required Action A.2 nor Condition B is applicable for APRM Functions 2.a, 2.b, 2.c, or2.d. Required Action A.2 is not applicable for Functions 2.a, 2.b, 2.c, or 2.d because in the newconfiguration, inoperability of one APRM channel affects both RPS trip systems. Thus, with aninoperable APRM channel, Required Action A.1 must be satisfied and is the only action (other than restoring operability) that will restore c apability to accommodate a single failure.Condition B also is not applicable because inoperability of more than one required APRMchannel results in loss of trip capability; thus, in this circumstance entry is required intoCondition C, as well as into Condition A for each channel. The licensee's justifications for these two changes are consistent with the APRM 2-out-of-4 voter function described in NEDC-32410P-A, its associated operability requirements, notes, operating modes, and actionstatements. The changes are consistent with NEDC-32410P-A and related topical reports. Therefore, the NRC staff finds these changes acceptable. 3.1.3.5Change 5 - Page 3.3-3, Section 3.3.1.1SR 3.3.1.1.2 is revised to delete the APRM gain adjustment required by LCO 3.2.4. Thedeleted portion is no longer required in the TSs due to the ARTS/MELLLA implementation. Therefore, the NRC staff finds this change acceptable.3.1.3.6Change 6 - Table 3.3.1.1-1, Reactor Protection System InstrumentationIn Change 6, the licensee proposed, in the table of SRs for LCO 3.3.1.1, revising the note inSR 3.3.1.1.9 to remove the APRM Function 2.a reference, which is now addressed inSR 3.3.1.1.13. This change is consistent with the TS changes recommended and approved bythe NRC staff in NEDC-32410P-A. Therefore, the NRC staff finds this change acceptable.3.1.3.7Change 7 - Table 3.3.1.1-1, Reactor Protection System InstrumentationIn Change 7, the licensee proposed deleting SR 3.3.1.1.11 and the corresponding surveillancefrequency. This proposed change reflected the inclusion of the recirculation flow loop calibrations as part of the overall Channel Calibration (SR 3.3.1.1.13) for APRM Function 2.b. SR 3.3.1.1.11 required a calibrated flow signal be used to verify the accuracy of the total loopdrive flow signal for the APRM Flow Biased Simulated Thermal Power - High function. Since calibration is proposed according to SR 3.3.1.1.13, deleting SR 3.3.1.1.11 is appropriate. TheNRC staff reviewed the proposed change and found it appropriate for BFN Unit 1 because it isconsistent with NEDC-32410P-A. Therefore, the NRC staff finds this change acceptable.3.1.3.8Change 8 - Table 3.3.1.1-1, Reactor Protection System InstrumentationIn Change 8, the licensee proposed adding a new note to SR 3.3.1.1.13 that excludes theneutron detectors from the channel calibration. As discussed in the TS Bases section, the neutron detectors are excluded from Channel Calibration because they are passive devices, with minimal drift, and because of the difficulty of simulating a meaningful signal. The NRC staff reviewed the proposed change and found it appropriate for BFN Unit 1 because it is consistent with NEDC-32410P-A. Therefore, the NRC staff finds this change acceptable.3.1.3.9Change 9 - Table 3.3.1.1-1, Reactor Protection System InstrumentationIn Change 9, the licensee proposed adding a new Channel Functional Test (SR 3.3.1.1.16) witha 184-day frequency. The licensee also proposed an accompanying note allowing 12 hours0.5 days <br />0.0714 weeks <br />0.0164 months <br /> to complete the requirement for APRM Function 2.a when entering MODE 2 from MODE 1. The licensee stated that testing of APRM Function 2.a cannot be performed in MODE 1 without utilizing jumpers, lifted leads, or movable links; consequently, the note is required to provide12-hours in which to bring current to the Channel Calibration for APRM Function 2.a when entering MODE 2 from MODE 1. The 12 hour1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> time requirement was based on operating experience and consideration of providing a reasonable time in which to complete the SR. The NRC staff reviewed the proposed change and found it appropriate for BFN Unit 1 because it isconsistent with NEDC-32410P-A. Therefore, the NRC staff finds this change acceptable.3.1.3.10Change 10 - Table 3.3.1.1-1, Reactor Protection System Instrumentation In Change 10, the licensee proposed five groups of changes (A, B, C, D, E) to LCO 3.3.1.1 andTable 3.3.1.1-1. 3.1.3.10.1 Change A. The licensee proposed changing from 2 to 3 the required minimumnumber of operable instrument channels per trip system for the APRM high and inoperablescram trip functions because the new configuration will have four total APRM channelscombined in a 2-out-of-4 logic. In the proposed configuration, a minimum of three of the four channels will be required operable to meet single failure criteria for the RPS trips initiated byAPRMs. Additionally, the licensee proposed adding Note "b" to Table 3.3.1.1-1 to highlight that,in the new configuration, each APRM instrument channel will provide input to both RPS tripsystems. These two changes were approved by the NRC staff in NEDC-32410P-A, therefore,the proposed changes are acceptable.3.1.3.10.2 Change B. The licensee proposed deleting the requirement for an APRMdownscale scram trip function. The licensee stated that the APRM downscale scram trip is not credited with performing any safety function. Deletion of this APRM function was approved by the NRC staff in NEDC-32410P-A, therefore, the proposed change is acceptable.3.1.3.10.3 Change C. The licensee proposed adding a new 2-out-of-4 voter function, with aminimum of two operable instrument channels per RPS trip system. This requirement isconsistent with the NUMAC-PRNMS hardware configuration. There are two voters per RPS trip system, and requiring two voters operable in each of the two RPS trip systems ensures that thesingle failure criteria is met. Because operability of the voters is required whenever any other APRM trip function is required, the applicable modes for voter operability are MODE 1 andMODE 2. Inoperability of one or more voters will result in entry to Condition A, Condition B, orCondition C, as appropriate. Failure to complete the required actions within the allowable completion times requires that the reactor be in MODE 3 (where APRM operability is notrequired) within 12 hours0.5 days <br />0.0714 weeks <br />0.0164 months <br />. These changes are consistent with the changes that were approved by the NRC staff in NEDC-32410P-A, therefore, the proposed changes are acceptable.3.1.3.10.4 Change D. The licensee proposed the following changes to the SRs for APRMFunctions 2.a, 2.b, 2.c, and 2.d (previously numbered "2.e"), and the addition of surveillancerequirements for the new APRM Function 2.e (2-out-of-4 voter). Specific discussions for each of the five functions are provided in the following sections.3.1.3.10.4.1 APRM Function 2.a, Neutron Flux - High (Setdown). For APRM Function forAPRM Function 2.a, Neutron Flux - High, (Setdown), the licensee proposed the followingchanges:Delete the Channel Functional Test (SR 3.3.1.1.3) with 7-day frequency and, in itsplace a Channel Functional Test (SR 3.3.1.1.16) with a 184-day frequency is added,Replace the 92-day Channel Calibration (SR 3.3.1.1.9) and the correspondingreference in SR 3.3.1.1.9 with the SR 3.3.1.1.13 Channel Calibration and an 18-monthfrequency, andDelete the 18-month Logic System Functional Test (SR 3.3.1.1.14).These changes are supported by the reliability analysis presented in NEDC-32410P-A, and areconsistent with the recommendations of NEDC-32410P-A. Therefore, the proposed changesare acceptable. 3.1.3.10.4.2 APRM Function 2.b, Flow Biased Simulated Thermal Power - High. For APRMFunction 2.b, Flow Biased Simulated Thermal Power - High, the licensee proposed the following changes:Replace the 92-day Channel Functional Test (SR 3.3.1.1.8) with the 184-day ChannelFunctional Test (SR 3.3.1.1.16),Replace the 92-day Channel Calibration (SR 3.3.1.1.9) and the correspondingreference in SR 3.3.1.1.9 with the 18-month Channel Calibration (SR 3.3.1.1.13),Include the 18-month flow signal calibration (SR 3.3.1.1.11) as part of the 18-monthSR 3.3.1.1.13, andDelete the 18-month Logic System Functional Test (SR 3.3.1.1.14).These changes in testing and surveillance are supported by the reliability analysis presented inNEDC-32410P-A, and are consistent with the recommendations of NEDC-32410P-A.
Therefore, the proposed changes are acceptable.3.1.3.10.4.3 APRM Function 2.c, Neutron Flux - High. For APRM Function 2.c, NeutronFlux - High, the licensee proposed the following changes:Replace the 92-day Channel Functional Test (SR 3.3.1.1.8) with a 184-day ChannelFunctional Test (SR 3.3.1.1.16),Replace the 92-day Channel Calibration (SR 3.3.1.1.9) and the correspondingreference in SR 3.3.1.1.9 with an 18-month Channel Calibration (SR 3.3.1.1.13), andDelete the 18-month Logic System Functional Test (SR 3.3.1.1.14).These changes in testing and surveillance are supported by the reliability analysis presented inNEDC-32410P-A, and are consistent with the recommendations of NEDC-32410P-A.
Therefore, the proposed changes are acceptable.3.1.3.10.4.4 APRM Function 2.d, Inop. For APRM Function 2.d, Inop, the licensee proposedthe following changes:Delete the calibration of local power range monitors (SR 3.3.1.1.7). This calibrationremains a requirement of APRM Functions 2.a, 2.b and 2.c, where the local power range monitors provide direct inputs to the process signals monitored by the APRM trip functions,Replace the 92-day Channel Functional Test (SR 3.3.1.1.8) with a 184-day ChannelFunctional Test (SR 3.3.1.1.16), andDelete the 18-month Logic System Functional Test (SR 3.3.1.1.14).These changes in testing and surveillance are supported by the reliability analysis presented inNEDC-32410P-A, and are consistent with the recommendations of NEDC-32410P-A.
Therefore, the proposed changes are acceptable.3.1.3.10.4.5 APRM Function 2.e, 2-out-of-4 voter. For the new APRM Function 2.e, 2-out-of-4voter, the licensee proposed the following additions to the TSs: A 24-hour Channel Check (SR 3.3.1.1.1) consistent with the Channel Check frequencyfor the other APRM Functions,An 18-month Logic System Functional Test (SR 3.3.1.1.14), andA 184-day Channel Functional Test (SR 3.3.1.1.16).These changes in testing and surveillance are supported by the reliability analysis presented inNEDC-32410P-A, and are consistent with the recommendations of NEDC-32410P-A.
Therefore, the proposed changes are acceptable.3.1.3.10.5 Change E. The licensee proposed changing the Allowable Value of APRMFunction 2.b., Flow Biased Simulated Thermal Power-HighThe licensee proposed to change the flow biased simulated thermal power-high from 0.58W+ 62% RTP and 120% RTP to 0.66W + 71% RTP and 120% RTP. The allowable valuefor single loop operation is similarly changed. The flow-biased APRM scram setpoint maximum (clamped) allowable value of 120% does not change.These changes incorporate new setpoints for the flow-biased APRM scram and rod blockfunctions based on the MELLLA analytical limits. Therefore, the NRC staff finds these c hangesacceptable. 3.1.3.11Change 11 - LCO 3.3.2.1 Control Rod Block Instrumentation SR 3.3.2.1.1 (Rod BlockMonitor Channel Functional Test)The licensee proposed changing the frequency of SR 3.3.2.1.1 from 92 days to 184 days. Thischange is supported by the reliability analysis presented in NEDC-32410P-A, and is consistentwith the recommendations of NEDC-32410P-A. Therefore, the NRC staff finds this c hangeacceptable.3.1.3.12Change 12 - LCO 3.3.2.1 Control Rod Block Instrumentation SR 3.3.2.1.4 (Rod BlockMonitor Channel Calibration)The licensee proposed changing the frequency of SR 3.3.2.1.4 from 92 days to 18 months. This change is supported by the reliability analysis presented in NEDC-32410P-A, and isconsistent with the recommendations of NEDC-32410P-A. Therefore, the NRC staff finds thischange acceptable.3.1.3.13Change 13 - Page 3.3-19, Section 3.3.2.1A new SR Section 3.3.2.1.8 is added to support the change to power-dependent RBMsetpoints. This SR has the same requirements as SR 3.3.2.1.4 in the BWR/4 ISTSs,NUREG-1433, Rev. 3. Changes in fuel types or licensed thermal power are not beingaddressed by this proposed change. Therefore, the NRC staff finds this acceptable becausethis change is consistent with NUREG-1433, Rev. 3. 3.1.3.14Change 14 - Page 3.3-20, Table 3.3.2.2-1The RBM portion of Table 3.3.2.1-1 and associated notes are revised to reflect the change fromflow-biased to power-dependent RBM limits. These proposed changes are consistent with Table 3.3.2.1-1 of BWR/4 ISTS NUREG-1433, Rev. 3. Changes in fuel types or licensedthermal power are not being addressed by this proposed change. Therefore, the NRC stafffinds this acceptable because this change is consistent with NUREG-1433, Rev. 3. 3.1.3.15Changes 15 and 16 The licensee proposed to modify Figure 3.4.1-1, Thermal Power versus Core Flow StabilityRegions, to expand Region II to include the power/flow map segment between 45 percent and 50 percent core flow. SR 3.4.1.2 was also proposed to be modified to match the requested change to figure 3.4.1-1. These changes will be addressed in the NRC staff review of theJanuary 6, 2006, submittal, and are not approved in this amendment.3.1.3.16Changes 17 (LCO 3.10.8.a) and 18 (SR 3.1.8.1), Shutdown Margin Test-RefuelingReference to function 2.d (now the "Inop" function) is added for consistency with the previouschanges to Table 3.3.1.1-1. Reference 2.e in LCO 3.10.8.a and SR 3.10.8.1 is changed tocorrespond to the new 2-out-of-4 voter function in table 3.3.1.1-1. These changes are editorial,therefore, the NRC staff finds them acceptable.3.1.3.17Bases Changes The licensee also provided the associated TS Bases that reflect the proposed TS changes asan attachment to its application. The TS Bases changes are consistent with the licensee's proposed plant-specific TS changes, and the NRC staff has no objections to the Baseschanges presented in the licensee's application. The changes related to the activation ofthermal-hydraulic stability monitoring instrumentation will be addressed in the NRC staff reviewof the January 6, 2006, submittal, and are not approved in this amendment.
4.0 STATE CONSULTATION
In accordance with the Commission's regulations, the NRC staff attempted to contact theAlabama State official regarding the proposed issuance of the amendment. There was no official response.
5.0 ENVIRONMENTAL CONSIDERATION
The amendment changes a requirement with respect to installation or use of a facilitycomponent located within the restricted area as defined in 10 CFR Part 20 and changes SRs.
The NRC staff has determined that the amendment involves no significant increase in theamounts, and no significant change in the types, of any effluents that may be released offsite, and that there is no significant increase in individual or cumulative occupational radiation exposure. The Commission has previously issued a proposed finding that the amendment involves no significant hazards consideration, and there has been no public comment on such finding (69 FR 5208). Accordingly, the amendment meets the eligibility criteria for categoricalexclusion set forth in 10 CFR 51.22(c)(9). Pursuant to 10 CFR 51.22(b), no environmental impact statement or environmental assessment need be prepared in connection with the issuance of the amendment.
6.0 CONCLUSION
The Commission has concluded, based on the considerations discussed above, that: (1) thereis reasonable assurance that the health and safety of the public will not be endangered byoperation in the proposed manner, (2) such activities will be conducted in compliance with theCommission's regulations, and (3) the issuance of the amendment will not be inimical to thecommon defense and security or to the health and safety of the public.
7.0REFERENCES
1.Letter from Abney, T. E., TVA, to USNRC, "BFN1-Unit 1-Proposed TS Change 431-Request for License Amendment-EPU Operation," TVA-BFN1-TS-431, dated June 28, 2004. (
Attachment:
"Browns Ferry Unit 1 Safety Analysis Report for Extended Power Uprate," NEDC-33101P, GE Nuclear Energy, June 2004.)2."Maximum Extended Load Line Limit And Arts Improvement Program Analyses(ARTS/MELLLA), Browns Ferry Nuclear Plant Unit 1, 2, 3," NEDC-32433P, GE Nuclear Energy, April 1995. 3."General Electric Standard Application for Reactor Fuel," GE Nuclear Energy, NEDE-24011-P-A-14 and NEDE-24011-P-A-14-US, Revision 14, June 2000. 4.NEDC-32484P, "BFN 1, 2, 3 SAFER/GESTR-LOCA Analysis," January 2002.
5.NEDE-23785P-A, Vol. III, Supplement 1, Revision 1, "GESTR-LOCA and SAFERModels for Evaluation of Loss-of-Coolant Accident Volume III, Supplement 1, AdditionalInformation for Upper Bound PCT Calculation," March 2002. 6.NEDO-20566A, "General Electric Model for LOCA analysis in Accordance with 10 CFR 50 Appendix K," September 1986. 7.Browns Ferry Nuclear plant Updated Final Safety Analysis Report (UFSAR).
8.NEDC-24154P-A, "Qualification of the One Dimensional Core Transient Model (ODYN)for Boiling Water Reactors (Supplement 1 - Volume 4)," February 2000. 9.NEDC-32523P-A, " Generic Evaluation of GE BWR EPU," February 2000.Principal Contributors: M. Waterman G. ThomasDate: September 27, 2006 Mr. Karl W. SingerBROWNS FERRY NUCLEAR PLANTTennessee Valley Authority
cc:
Mr. Ashok S. Bhatnagar, Senior Vice President Nuclear Operations Tennessee Valley Authority 6A Lookout Place 1101 Market Street Chattanooga, TN 37402-2801 Mr. Larry S. Bryant, Vice PresidentNuclear Engineering & Technical Services Tennessee Valley Authority 6A Lookout Place 1101 Market Street Chattanooga, TN 37402-2801Brian O'Grady, Site Vice PresidentBrowns Ferry Nuclear Plant Tennessee Valley Authority P.O. Box 2000 Decatur, AL 35609Mr. Robert J. Beecken, Vice PresidentNuclear Support Tennessee Valley Authority 6A Lookout Place 1101 Market Street Chattanooga, TN 37402-2801 General CounselTennessee Valley Authority ET 11A 400 West Summit Hill DriveKnoxville, TN 37902Mr. John C. Fornicola, ManagerNuclear Assurance and Licensing Tennessee Valley Authority 6A Lookout Place 1101 Market Street Chattanooga, TN 37402-2801Mr. Bruce Aukland, Plant ManagerBrowns Ferry Nuclear Plant Tennessee Valley Authority P.O. Box 2000 Decatur, AL 35609Mr. Masoud Bajestani, Vice PresidentBrowns Ferry Unit 1 Restart Browns Ferry Nuclear Plant Tennessee Valley Authority P.O. Box 2000 Decatur, AL 35609Mr. Robert G. Jones, General ManagerBrowns Ferry Site Operations Browns Ferry Nuclear Plant Tennessee Valley Authority P.O. Box 2000 Decatur, AL 35609Mr. Larry S. MellenBrowns Ferry Unit 1 Project Engineer Division of Reactor Projects, Branch 6 U.S. Nuclear Regulatory Commission 61 Forsyth Street, SW.
Suite 23T85 Atlanta, GA 30303-8931 Mr. Glenn W. Morris, Manager Corporate Nuclear Licensing and Industry Affairs Tennessee Valley Authority 4X Blue Ridge 1101 Market Street Chattanooga, TN 37402-2801Mr. William D. Crouch, M anagerLicensing and Industry Affairs Browns Ferry Nuclear Plant Tennessee Valley Authority P.O. Box 2000 Decatur, AL 35609Senior Resident InspectorU.S. Nuclear Regulatory Commission Browns Ferry Nuclear Plant 10833 Shaw Road Athens, AL 35611-6970State Health OfficerAlabama Dept. of Public Health RSA Tower - Administration Suite 1552 P.O. Box 303017 Montgomery, AL 36130-3017ChairmanLimestone County Commission 310 West Washington Street Athens, AL 35611