ML16049A071: Difference between revisions
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
||
(2 intermediate revisions by the same user not shown) | |||
Line 15: | Line 15: | ||
=Text= | =Text= | ||
{{#Wiki_filter:Job Performance Measure (JPM) | {{#Wiki_filter:Job Performance Measure (JPM) | ||
RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: | SITE: BFN JPM TITLE: RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: 80A U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: RO: 3.2 SRO: 3.3 201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL K/A No. &STATEMENT: CONTROL SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Rod Drift Alarm RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 1 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | ||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: | Validated by: | ||
RO: | Validator Date Approved by: | ||
201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL CONTROL SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Rod Drift Alarm RELATED PRA INFORMATION: | Site Training Management Date Approved by: | ||
Risk Significant SAFETY FUNCTION: | Site Training Program Owner Date 1 | ||
1 | |||
In-Plant | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: __80A__ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to respond to a Control Rod Drift In per 2-AOI-85-5. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-85-5, 2-AOI-100-1 VALIDATIONTIME: 18 min PERFORMANCE TIME: | ||
2-AOI-85-5 , 2-AOI-100-1 VALIDATIONTIME: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/10 All Initial issue Incorrect task number; changed to U-085-AB-05: | |||
1 09/01/15 1 Incorrect malfunction numbers; rd07r0231, rd07r2223 & rd07r3031; Corrected 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 280 | |||
* Reset IC 28 or Exam IC if written in above | |||
* Run schedule file:NRC JPM A U2 -Control Rod Drift In | |||
* Verify all triggers and overrides are correct | |||
* Place the simulator in RUN to ensure stable conditions Console | |||
* Start Rod Display on RWM Screen Operator Instructions | |||
- | * Provide Initial Rod Data Sheet -PRLOG | ||
* When prompted by the examiner, INSERT - Event 1 to Drift Control Rod 02-31 into the core | |||
* When prompted by the examiner, INSERT - Event 2 to Drift Control Rod Multiple Control Rods into the core Malfunctions Description Event Severity Delay Initial set rd07r0231 Drifts rod 02-31 into 1 NA 35 sec NA core rd07r2223 Drifts rod 22-23 into 2 NA 10 sec NA core rd07r3031 Drifts rod 30-31 into 2 NA 25 sec NA core rd07r4635 Drifts rod 46-35 into 2 NA 20 sec NA core rd07r2619 Drifts rod 26-19 into 2 NA 30 sec NA core rd07r3027 Drifts rod 30-27 into 2 NA 18 sec NA core rd07r5423 Drifts rod 54-23 into 2 NA 23 sec NA core rd07r2255 Drifts rod 22-55 into 2 NA 28 sec NA core 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): NRC JPM A U2 -Control Rod Drift In 5 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
The Reactor is at 100% power INITIATING CUES | * The Reactor is at 100% power INITIATING CUES: | ||
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | |||
6 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
NOTE | |||
: 1) Problem details of any control rod issues observed during the performance of this surveillance must be recorded on Attachment 3 for further review and possible corrective maintenance. Slow/fast rod movements or settle times should be noted in the remarks section. | |||
: 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1. | : 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1. | ||
CAUTIONS 1) Any mispositioned control rod events will be dispositioned by following the direction contained within 2 | CAUTIONS | ||
-AOI-85-7. 2) If a control rod moves unexpectedly one notch beyond its intended position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. | : 1) Any mispositioned control rod events will be dispositioned by following the direction contained within 2-AOI-85-7. | ||
: 3) At any time CTP is less than or equal to 10%, entry into LCO 3.1.6 may be required. | : 2) If a control rod moves unexpectedly one notch beyond its intended Critical Step position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. SAT | ||
: 3) At any time CTP is less than or equal to 10%, entry into LCO 3.1.6 UNSAT may be required. | |||
N/A 7.3 Exercising a Partially Withdrawn Control Rod | |||
a Partially Withdrawn Control Rod | [1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. | ||
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2 | |||
-XS-85-40. | |||
[2] OBSERVE the following for selected control rod: | [2] OBSERVE the following for selected control rod: | ||
CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. | * CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. | ||
CHECK white light on the Full Core Display is ILLUMINATED. | * CHECK white light on the Full Core Display is ILLUMINATED. | ||
CHECK Rod Out Permit light is ILLUMINATED. | * CHECK Rod Out Permit light is ILLUMINATED. | ||
Standard: | Standard: | ||
Selects a withdrawn control rod Note to Examiner: May select any partially withdrawn control rod in any order 7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 2: | |||
Job Performance Measure (JPM) | [3] INSERT control rod one notch by performing the following: | ||
[3.1] PLACE CRD CONTROL SWITCH, 2 | Critical Step | ||
-HS-85-48 in ROD IN andRELEASE. | [3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN andRELEASE. SAT | ||
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | [3.2] OBSERVE control rod settles into the desired position UNSAT andROD SETTLE light extinguishes. | ||
Standard: | N/A Standard: | ||
Inserts withdrawn control rod one notch Step 3: | |||
[4] WITHDRAW selected control rod one notch by performing the following: Critical Step | |||
[4] WITHDRAW selected control rod one notch by performing the following: | [4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD OUT NOTCHand RELEASE. SAT | ||
[4.1] PLACE CRD CONTROL SWITCH, 2 | [4.2] OBSERVE control rod settles into the desired position and UNSAT ROD SETTLE light extinguishes. | ||
-HS-85-48 in ROD OUT NOTCHand RELEASE. | N/A Standard: | ||
Withdraws withdrawn control rod one notch Step 4: | |||
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | |||
Standard: Withdraws withdrawn control rod one notch | |||
[5] DOCUMENT completion of control rod test as follows: | [5] DOCUMENT completion of control rod test as follows: | ||
[5.1] PERFORMER INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the control rodjust exercised to document proper movement and CRD latching. | [5.1] PERFORMER | ||
[5.2] Concurrent Verifier (CV) | * INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the SAT control rodjust exercised to document proper movement and CRD latching. UNSAT | ||
ENSURE rod inserted and returned to its original position. | [5.2] Concurrent Verifier (CV) N/A | ||
INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised. | * ENSURE rod inserted and returned to its original position. | ||
* INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised. | |||
8 | |||
CONTINUOUS IN. (Otherwise N/A) | Job Performance Measure (JPM) | ||
[3] IF a Control Rod Block occurs during rod insertion due to Rod Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above. (Otherwise N/A) | STEP / STANDARD SAT / UNSAT Standard: | ||
Standard: Responds per 2-AOI-85-5 and inserts control rod 02 | Initials Attachment 1 for exercised control rod and continues to exercise rods. | ||
-31 to full in position as indicated by position 00 indication. | Note to Examiner: | ||
* Perform above actions for @ least two control rods. | |||
-AOI-85-5 , Control Rod Drift In. | * When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #1 for Control Rod 02-31 Drift In Note to Simulator Booth Operator: | ||
* When directed by examiner insert trigger #1 for 02-31 Control Rod Drift In. | |||
Step 5: | |||
Performer recognizes control rod 02-31 drift in and responds per 2-AOI-85-5. | |||
[2] IF a Control Rod is moving from its intended position without Critical Step operator actions, THEN INSERT the Control Rod to position 00 using CONTINUOUS IN. (Otherwise N/A) SAT | |||
[3] IF a Control Rod Block occurs during rod insertion due to Rod UNSAT Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above. | |||
(Otherwise N/A) N/A Standard: | |||
Responds per 2-AOI-85-5 and inserts control rod 02-31 to full in position as indicated by position 00 indication. | |||
CUE: When report to US, state Respond per 2-AOI-85-5, Control Rod Drift In. | |||
Step 6: | Step 6: | ||
[4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod pattern. Standard: Candidate notifies Reactor Engineer to Evaluate Core Thermal limits and Preconditioning Limits for the current Control Rod Pattern | [4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod SAT pattern. | ||
UNSAT Standard: | |||
Candidate notifies Reactor Engineer to Evaluate Core N/A Thermal limits and Preconditioning Limits for the current Control Rod Pattern Cue: Understand Reactor Engineering notified to evaluate Core Thermal andPreconditioning Limits 9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-AOI-100-1. | STEP / STANDARD SAT / UNSAT Step 7: | ||
[6] CHECK Thermal Limits on ICS (RUNMON). | [5] IF another Control Rod Drift occurs before Reactor Engineering completes the evaluation, | ||
Note to NRC Examiner: | * THEN MANUALLY SCRAM Reactor and enter 2-AOI-100-1. SAT | ||
Step [6] performed by Reactor | [6] CHECK Thermal Limits on ICS (RUNMON). UNSAT Note to NRC Examiner: Step [6] performed by Reactor N/A Engineering. | ||
Standard: | Standard: | ||
Reviews step and asks for guidance from US or RE CUE: As Shift Manager, state RE has evaluated Core Thermal and Preconditioning Limits and has determined that the Control Rod Exercise may continue and that any other Control Rod Drift will be considered the first. | |||
Student will continue with Control Rod Exercise. | Student will continue with Control Rod Exercise. | ||
Step 8: | Step 8: | ||
7.3 Exercising a Partially Withdrawn Control Rod | |||
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. Critical Step | |||
[2] OBSERVE the following for selected control rod: SAT | |||
* CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. UNSAT | |||
* CHECK white light on the Full Core Display is ILLUMINATED. | |||
* CHECK Rod Out Permit light is ILLUMINATED. N/A Standard: | |||
Selects a withdrawn control rod 10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 9: | |||
[3] INSERT control rod one notch by performing the following: | |||
Critical Step | |||
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN SAT andRELEASE. | |||
UNSAT | |||
[3.1] PLACE CRD CONTROL SWITCH, 2 | |||
-HS-85-48 in ROD IN andRELEASE. | |||
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | [3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | ||
Standard: | N/A Standard: | ||
Inserts withdrawn control rod one notch Step 10: | |||
[4] WITHDRAW selected control rod one notch by performing the Critical Step following: | |||
[4] WITHDRAW selected control rod one notch by performing the following: | [4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD SAT OUT NOTCHand RELEASE. | ||
[4.1] PLACE CRD CONTROL SWITCH, 2 | UNSAT | ||
-HS-85-48 in ROD OUT NOTCHand RELEASE. | |||
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | [4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | ||
Standard: Withdraws withdrawn control rod one notch Critical Step | N/A Standard: | ||
Withdraws withdrawn control rod one notch Note to Examiner: | |||
When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #2 for Multiple Control Rods Drifting In Step 11: | |||
Multiple Control Rods Drifting In Critical Step Standard: | |||
Recognizes Multiple Control Rods Drift into the Core and Manually SAT Scrams the Reactor per 2-AOI-85-5. | |||
UNSAT | |||
* Depresses both SCRAM Pushbuttons | |||
* Places mode switch in shutdown N/A | |||
* Verifies All Rods in 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 11 continued: | |||
* Performs a Scram Announcement Critical Step o Rx Mode Switch Position: Shutdown o Rod Position: All Full In SAT o Reactor Water Level ____ & Trend ___ | |||
o Reactor Pressure ____ & Trend ___ UNSAT o MSIV Position: OPEN o Rx Power: <5% N/A Termination Criteria: REPEAT BACK SCRAM REPORT THEN STATE, THIS COMPLETES THE JPM. THAT WILL BE ALL FOR NOW, ANOTHER OPERATOR WILL CONTINUE IN 2-AOI-100-1. | |||
STOP TIME: | |||
12 | |||
Job Performance Measure (JPM) | |||
o Reactor Pressure ____ & Trend ___ | |||
o MSIV Position: OPEN o Rx Power: <5 | |||
% | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
The Reactor is at 100% power | * The Reactor is at 100% power INITIATING CUES: | ||
INITIATING CUES | |||
: | |||
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | ||
13 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: | SITE: BFN JPM TITLE: RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: 80A U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: RO: 3.2 SRO: 3.3 201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL CONTROL SYSTEM ; and (b) based on K/A No. &STATEMENT: | ||
those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: | |||
SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): | Rod Drift Alarm RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 1 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | ||
U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
RO: | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL CONTROL SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Rod Drift Alarm RELATED PRA INFORMATION: | Validated by: | ||
Risk Significant SAFETY FUNCTION: | Validator Date Approved by: | ||
1 | Site Training Management Date Approved by: | ||
In-Plant | Site Training Program Owner Date 1 | ||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _80A U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to respond to a Control Rod Drift In per 3-AOI-85-5. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 3-AOI-85-5, 3-AOI-100-1 VALIDATIONTIME: | ||
3-AOI-85-5 , 3-AOI-100-1 | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/10 All Initial issue Incorrect task number; changed to U-085-AB-05: | |||
1 05/11/15 1 Incorrect malfunction numbers; rd07r0231, rd07r2223 & rd07r3031; Corrected 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 280 | |||
* Reset IC 28 or Exam IC if written in above | |||
* Run schedule file: NRC JPM A U3 -Control Rod Drift In | |||
* Verify all triggers and overrides are correct | |||
* Place the simulator in RUN to ensure stable conditions Console Operator | |||
* Start Rod Display on RWM Screen Instructions | |||
* Provide Initial Rod Data Sheet -PRLOG | |||
- | * When prompted by the examiner, INSERT - Event 1 to Drift Control Rod 02-31 into the core | ||
* When prompted by the examiner, INSERT - Event 2 to Drift Control Rod Multiple Control Rods into the core Malfunctions Description Event Severity Delay Initial set rd07r0231 Drifts rod 02-31 into 1 NA 35 sec NA core rd07r2223 Drifts rod 22-23 into 2 NA 10 sec NA core rd07r3031 Drifts rod 30-31 into 2 NA 25 sec NA core rd07r4635 Drifts rod 46-35 into 2 NA 20 sec NA core rd07r2619 Drifts rod 26-19 into 2 NA 30 sec NA core rd07r3027 Drifts rod 30-27 into 2 NA 18 sec NA core rd07r5423 Drifts rod 54-23 into 2 NA 23 sec NA core rd07r2255 Drifts rod 22-55 into 2 NA 28 sec NA core 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): NRC JPM A U3 -Control Rod Drift In 5 | |||
-Control Rod Drift In | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit 3. | |||
You are an Operator on Unit | * The Reactor is at 100% power INITIATING CUES: | ||
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | |||
6 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
NOTE | |||
: 1) Problem details of any control rod issues observed during the performance of this surveillance must be recorded on Attachment 3 for further review and possible corrective maintenance. Slow/fast rod movements or settle times should be noted in the remarks section. | |||
: 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1. | : 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1. | ||
CAUTIONS 3) Any mispositioned control rod events will be dispositioned by following the direction contained within 3-AOI-85-7. | CAUTIONS | ||
: 4) If a control rod moves unexpectedly one notch beyond its intended position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. | : 3) Any mispositioned control rod events will be dispositioned by following the direction contained within 3-AOI-85-7. | ||
: 5) At any time CTP is less than or equal to 10%, entry into LCO 3.1.6 may be required. | : 4) If a control rod moves unexpectedly one notch beyond its intended Critical Step position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. SAT | ||
: 5) At any time CTP is less than or equal to 10%, entry into LCO 3.1.6 UNSAT may be required. | |||
N/A 7.3 Exercising a Partially Withdrawn Control Rod | |||
a Partially Withdrawn Control Rod | |||
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 3-XS-85-40. | [1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 3-XS-85-40. | ||
[2] OBSERVE the following for selected control rod: | [2] OBSERVE the following for selected control rod: | ||
CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. | * CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. | ||
CHECK white light on the Full Core Display is ILLUMINATED. | * CHECK white light on the Full Core Display is ILLUMINATED. | ||
CHECK Rod Out Permit light is ILLUMINATED. | * CHECK Rod Out Permit light is ILLUMINATED. | ||
Standard: | Standard: | ||
Selects a withdrawn control rod Note to Examiner: May select any partially withdrawn control rod in any order 7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 2: | |||
Job Performance Measure (JPM) | [3] INSERT control rod one notch by performing the following: | ||
[3.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD IN andRELEASE. | Critical Step | ||
Standard: | [3.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD IN andRELEASE. SAT | ||
[3.2] OBSERVE control rod settles into the desired position UNSAT andROD SETTLE light extinguishes. | |||
N/A Standard: | |||
[4] WITHDRAW selected control rod one notch by performing the following: | Inserts withdrawn control rod one notch Step 3: | ||
[4.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD OUT NOTCHand RELEASE. | [4] WITHDRAW selected control rod one notch by performing the following: Critical Step | ||
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | [4.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD OUT NOTCHand RELEASE. SAT | ||
Standard: Withdraws withdrawn control rod one notch | [4.2] OBSERVE control rod settles into the desired position and UNSAT ROD SETTLE light extinguishes. | ||
N/A Standard: | |||
Withdraws withdrawn control rod one notch Step 4: | |||
[5] DOCUMENT completion of control rod test as follows: | [5] DOCUMENT completion of control rod test as follows: | ||
[5.1] PERFORMER INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the control rodjust exercised to document proper movement and CRD latching. | [5.1] PERFORMER | ||
[5.2] Concurrent Verifier (CV) | * INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the SAT control rodjust exercised to document proper movement and CRD latching. UNSAT | ||
ENSURE rod inserted and returned to its original position. | [5.2] Concurrent Verifier (CV) N/A | ||
INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised. | * ENSURE rod inserted and returned to its original position. | ||
* INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised. | |||
8 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Standard: | |||
Initials Attachment 1 for exercised control rod and continues to exercise rods. | |||
Note to Examiner: | |||
* Perform above actions for @ least two control rods. | |||
* When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #1 for Control Rod 02-31 Drift In Note to Simulator Booth Operator: | |||
* When directed by examiner insert trigger #1 for 02-31 Control Rod Drift In. | |||
Step 5: | |||
Performer recognizes control rod 02-31 drift in and responds per 3-AOI-85-5. | |||
[2] IF a Control Rod is moving from its intended position without Critical Step operator actions, THEN INSERT the Control Rod to position 00 using CONTINUOUS IN. (Otherwise N/A) SAT | |||
[3] IF a Control Rod Block occurs during rod insertion due to Rod UNSAT Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above. | |||
(Otherwise N/A) N/A Standard: | |||
Responds per 3-AOI-85-5 and inserts control rod 02-31 to full in position as indicated by position 00 indication. | |||
CUE: When report to US, state Respond per 3-AOI-85-5, Control Rod Drift In. | |||
Step 6: | Step 6: | ||
[4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod pattern. Standard: Candidate notifies Reactor Engineer to Evaluate Core Thermal limits and Preconditioning Limits for the current Control Rod Pattern | [4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod SAT pattern. | ||
UNSAT Standard: | |||
Candidate notifies Reactor Engineer to Evaluate Core N/A Thermal limits and Preconditioning Limits for the current Control Rod Pattern Cue: Understand Reactor Engineering notified to evaluate Core Thermal andPreconditioning Limits 9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-AOI-100-1. | STEP / STANDARD SAT / UNSAT Step 7: | ||
[6] CHECK Thermal Limits on ICS (RUNMON). | [5] IF another Control Rod Drift occurs before Reactor Engineering completes the evaluation, | ||
Note to NRC Examiner: | * THEN MANUALLY SCRAM Reactor and enter 2-AOI-100-1. SAT | ||
Step [6] performed by Reactor | [6] CHECK Thermal Limits on ICS (RUNMON). UNSAT Note to NRC Examiner: Step [6] performed by Reactor N/A Engineering. | ||
Standard: | Standard: | ||
Reviews step and asks for guidance from US or RE CUE: As Shift Manager, state RE has evaluated Core Thermal and Preconditioning Limits and has determined that the Control Rod Exercise may continue and that any other Control Rod Drift will be considered the first. | |||
Student will continue with Control Rod Exercise. | Student will continue with Control Rod Exercise. | ||
Step 8: | Step 8: | ||
7.3 Exercising a Partially Withdrawn Control Rod | |||
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. Critical Step | |||
[2] OBSERVE the following for selected control rod: SAT | |||
* CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. UNSAT | |||
* CHECK white light on the Full Core Display is ILLUMINATED. | |||
* CHECK Rod Out Permit light is ILLUMINATED. N/A Standard: | |||
Selects a withdrawn control rod 10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 9: | |||
[3] INSERT control rod one notch by performing the following: | |||
Critical Step | |||
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN SAT andRELEASE. | |||
UNSAT | |||
[3.1] PLACE CRD CONTROL SWITCH, 2 | |||
-HS-85-48 in ROD IN andRELEASE. | |||
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | [3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | ||
Standard: | N/A Standard: | ||
Inserts withdrawn control rod one notch Step 10: | |||
[4] WITHDRAW selected control rod one notch by performing the Critical Step following: | |||
[4] WITHDRAW selected control rod one notch by performing the following: | [4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD SAT OUT NOTCHand RELEASE. | ||
[4.1] PLACE CRD CONTROL SWITCH, 2 | UNSAT | ||
-HS-85-48 in ROD OUT NOTCHand RELEASE. | |||
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | [4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | ||
Standard: Withdraws withdrawn control rod one notch Critical Step | N/A Standard: | ||
Withdraws withdrawn control rod one notch Note to Examiner: | |||
When satisfied with the number of rod manipulations direct Simulator BoothOperator to insert trigger #2 for Multiple Control Rods Drifting In Step 11: | |||
Multiple Control Rods Drifting In Standard: Critical Step Recognizes Multiple Control Rods Drift into the Core and Manually Scrams the Reactor per 3-AOI-85-5. SAT | |||
* Depresses both SCRAM Pushbuttons UNSAT | |||
* Places mode switch in shutdown | |||
* Verifies All Rods in N/A 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 11 continued: | |||
Job Performance Measure (JPM) | |||
Critical Step | Critical Step | ||
* Performs a Scram Announcement o Rx Mode Switch Position: Shutdown SAT o Rod Position: All Full In o Reactor Water Level ____ & Trend ___ UNSAT o Reactor Pressure ____ & Trend ___ | |||
o MSIV Position: OPEN N/A o Rx Power: <5% | |||
Termination Criteria: repeat back scram report then state, this completes the JPM. That will be all for now, another operator will continue in 2-AOI-100-1 STOP TIME: | |||
12 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
Job Performance Measure (JPM) | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit | You are an Operator on Unit 3. | ||
* The Reactor is at 100% power INITIATING CUES: | |||
INITIATING CUES | |||
: | |||
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | ||
13 | |||
Job Performance Measure (JPM) | |||
SITE: BFN JPM TITLE: EHC Auto Cooldown JPM NUMBER: 276 U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-NO-32 Perform Reactor Cooldown TASK NUMBER / TASK TITLE(S): U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: RO: 3.9 SRO: 3.9 239001Main and Reheat Steam System: A4.09 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 4 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _276 U2 RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to initiate an Auto Cooldown with Turbine Bypass Valves. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-OI-47 VALIDATIONTIME: 4 min PERFORMANCE TIME: | ||
2-OI-47 VALIDATIONTIME: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 06/19/12 All Initial issue 1 07/22/15 All General revision & re-format 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 40 Exam IC 281 | |||
* Reset IC 40 or Exam IC if written in above | |||
* Ensure RFP is in Manual on PDS controller with plant parameters stable. | |||
Console Operator Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): None 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
* The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 2-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6]. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: SAT | |||
[6] VERIFY EHC is in Pressure Control using 2-HS-47-204. UNSAT N/A Standard: | |||
Observes light on for EHC Pressure Control on 2-HS-47-204. | |||
Step 2: | |||
: | [7] On the EHC Work Station on Panel 9-7: | ||
[7.1] SELECT Main Menu from the toolbar at bottom of the screen. Critical Step | |||
- | [7.2] SELECT Log In on Display Screen and ENTER OPS SAT for name and OPS for Password. | ||
UNSAT | |||
[7.3] SELECT Auto Cooldown from list of function on the screen. N/A Standard: | |||
Candidate logs into EHC workstation and selects Auto Cooldown from the list of functions on the screen. | |||
Step 3: | |||
[8] On the Auto Cooldown Display Screen CHECK the following are displayed. | |||
SAT | |||
* Turbine Tripped or All Valves Closed - indicates Reset. | |||
* Rx Press Ctrl - indicates Reset. UNSAT Standard: N/A | |||
* Candidate checks the Turbine Tripped or All Valves Closed | |||
-indicates Reset. | |||
* Candidate checks Rx Press Ctrl - indicates Reset. | |||
6 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 4: | |||
[9] On the Auto Cooldown Screen SET the desired Final Pressure for cooldown as follows: | |||
[9.1] SELECT the block above the FINAL PRESSURE Critical Step TARGET. | |||
SAT | |||
[9.2] ENTER the desired pressure using the Display Screen or Key Board. | |||
UNSAT | |||
[9.3] WHEN desired Pressure is entered SELECT OK N/A Standard: | |||
Candidate sets the desired final target pressure of 20psig (given in initial conditions). | |||
Step 5: | |||
[10] WHEN Cooldown is ready to commence, THEN | |||
[9.1] SELECT the block above the | |||
[9.3] WHEN desired Pressure is entered SELECT | |||
[10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary) | [10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary) | ||
[10.2] DEPRESS the | Critical Step | ||
[11] WHEN Caution | [10.2] DEPRESS the START button on the Auto Cooldown Display Screen. SAT | ||
Standard: | [11] WHEN Caution Are You Sure You Want to Initiate Auto UNSAT Cooldown? appears N/A SELECT Yes Screen Button to start the cooldown. | ||
Standard: | |||
Candidate depresses START and acknowledges YES to commence auto cooldown. | |||
7 | |||
SAT | Job Performance Measure (JPM) | ||
[13] | STEP / STANDARD SAT / UNSAT Step 6: | ||
[12] CHECK the following: | |||
* EHC PRESSURE SETPOINT, 2-PI-47-162, is lowering. | |||
* EHC AUTO COOLDOWN displays IN PROGRESS SAT Standard: UNSAT Candidate monitors EHC pressure and the auto cooldown is IN N/A PROGRESS. | |||
Cue: The Unit Supervisor directs you to adjust the Final Pressure Target to 100 psig. | |||
Step 7: | |||
[13] IF it is desired to change the Final Pressure Target, THEN On the Auto Cooldown Screen. | |||
[13.1] SELECT the block above the FINAL PRESSURE TARGET Critical Step | |||
[13.2] ENTER the desired pressure using the Display SAT Screen or Key Board. | |||
UNSAT | |||
[13.3] WHEN desired Pressure is entered SELECT OK N/A Standard: | |||
Candidate adjusts FINAL PRESSURE TARGET to 100 psig and recommences the auto cooldown. | |||
Evaluator Cue: Another operator will continue to monitor the cooldown. This completes your task. | |||
STOP TIME: | |||
8 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
* The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
Job Performance Measure (JPM) | INITIATING CUES: | ||
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 2-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6]. | |||
9 | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
INITIATING CUES | |||
Job Performance Measure (JPM) | |||
SITE: BFN JPM TITLE: EHC Auto Cooldown JPM NUMBER: 276 U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-NO-32 Perform Reactor Cooldown TASK NUMBER / TASK TITLE(S): U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: RO: 3.9 SRO: 3.9 239001Main and Reheat Steam System: A4.09 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 4 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Job Performance Measure (JPM) | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
EHC Auto Cooldown JPM NUMBER: | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
276 | Validated by: | ||
SRO STA UO NAUO | Validator Date Approved by: | ||
U-000-NO-32 Perform Reactor Cooldown U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: | Site Training Management Date Approved by: | ||
RO: | Site Training Program Owner Date 1 | ||
239001Main and Reheat Steam System: A4.09 Ability to manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: | |||
Risk Significant SAFETY FUNCTION: | |||
4 | |||
In-Plant | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _276 U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to initiate an Auto Cooldown with Turbine Bypass Valves. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 3-OI-47 VALIDATIONTIME: | ||
3-OI-47 | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 06/19/12 All Initial issue 1 07/22/15 All General revision & re-format 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 40 Exam IC 281 | |||
* Reset IC 40 or Exam IC if written in above | |||
* Ensure RFP is in Manual on PDS controller with plant parameters stable. | |||
Console Operator Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): None 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 3-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6]. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
[6] VERIFY EHC is in Pressure Control using 3-HS-47-204. SAT UNSAT Standard: | |||
N/A Observes light on for EHC Pressure Control on 3-HS-47-204. | |||
Step 2: | |||
[7] On the EHC Work Station on Panel 9-7: | |||
[7.1] SELECT Main Menu from the toolbar at bottom of the screen. Critical Step | |||
Job Performance Measure (JPM) | [7.2] SELECT Log In on Display Screen and ENTER OPS SAT for name and OPS for Password. | ||
-HS-47-204. Standard: | UNSAT | ||
Observes light on for EHC Pressure Control on 3 | [7.3] SELECT Auto Cooldown from list of function on the screen. N/A Standard: | ||
-HS-47-204. | Candidate logs into EHC workstation and selects Auto Cooldown from the list of functions on the screen. | ||
[7] On the EHC Work Station on Panel 9 | Step 3: | ||
-7: | [8] On the Auto Cooldown Display Screen CHECK the following are displayed. | ||
[7.3] | SAT | ||
* Turbine Tripped or All Valves Closed - indicates Reset. | |||
[8] On the Auto Cooldown Display Screen | * Rx Press Ctrl - indicates Reset. UNSAT Standard: N/A | ||
* Candidate checks the Turbine Tripped or All Valves Closed | |||
CHECK the following are displayed. | -indicates Reset. | ||
Turbine Tripped or All Valves Closed | * Candidate checks Rx Press Ctrl - indicates Reset. | ||
- indicates Reset. | 6 | ||
Rx Press Ctrl | |||
- indicates Reset. | |||
Standard: | |||
-indicates Reset. | |||
Candidate checks Rx Press Ctrl | |||
- indicates Reset. | |||
[9.3] WHEN desired Pressure is entered SELECT | Job Performance Measure (JPM) | ||
Step 4: | |||
[9] On the Auto Cooldown Screen SET the desired Final Pressure for cooldown as follows: | |||
[9.1] SELECT the block above the FINAL PRESSURE Critical Step TARGET. | |||
SAT | |||
[9.2] ENTER the desired pressure using the Display Screen or Key Board. | |||
UNSAT | |||
[9.3] WHEN desired Pressure is entered SELECT OK N/A Standard: | |||
Candidate sets the desired final target pressure of 20psig (given in initial conditions). | |||
Step 5: | |||
[10] WHEN Cooldown is ready to commence, THEN | |||
[10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary) | [10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary) | ||
[10.2] DEPRESS the | Critical Step | ||
[11] WHEN Caution | [10.2] DEPRESS the START button on the Auto Cooldown Display Screen. SAT | ||
Standard: | [11] WHEN Caution Are You Sure You Want to Initiate Auto UNSAT Cooldown? appears N/A SELECT Yes Screen Button to start the cooldown. | ||
Standard: | |||
Candidate depresses START and acknowledges YES to commence auto cooldown. | |||
7 | |||
SAT | Job Performance Measure (JPM) | ||
[13] | Step 6: | ||
[12] CHECK the following: | |||
* EHC PRESSURE SETPOINT, 3-PI-47-162, is lowering. | |||
* EHC AUTO COOLDOWN displays IN PROGRESS SAT Standard: UNSAT Candidate monitors EHC pressure and the auto cooldown is IN N/A PROGRESS. | |||
Cue: The Unit Supervisor directs you to adjust the Final Pressure Target to 100 psig. | |||
Step 7: | |||
[13] IF it is desired to change the Final Pressure Target, THEN On the Auto Cooldown Screen. | |||
[13.1] SELECT the block above the FINAL PRESSURE TARGET Critical Step | |||
[13.2] ENTER the desired pressure using the Display SAT Screen or Key Board. | |||
UNSAT | |||
[13.3] WHEN desired Pressure is entered SELECT OK N/A Standard: | |||
Candidate adjusts FINAL PRESSURE TARGET to 100 psig and recommences the auto cooldown. | |||
Evaluator Cue: Another operator will continue to monitor the cooldown. This completes your task. | |||
STOP TIME: | |||
8 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 3-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6]. | |||
9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
LOSS OF REFERENCE APRM TO ROD BLOCK SITE: BFN JPM TITLE: | |||
MONITOR JPM NUMBER: 672A U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-085-AL-03 RESPOND TO CONTROL ROD TASK NUMBER / TASK TITLE(S): | |||
WITHDRAWL BLOCK K/A RATINGS: RO: 3.1 SRO: 3.3 215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures K/A No. &STATEMENT: | |||
to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR-3,4,5 RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 7 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
672A U2 REVISION: 0 | |||
SRO STA UO NAUO | |||
U-085-AL-03 RESPOND TO CONTROL ROD WITHDRAWL BLOCK K/A RATINGS: | |||
RO: | |||
215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR | |||
-3,4,5 RELATED PRA INFORMATION: | |||
Risk Significant SAFETY FUNCTION: | |||
7 | |||
ALTERNATE PATH (Y/N) | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _672A U2_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to bypass an APRM Channel and clear a Control Rod Block from Rod Block Monitoring System. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-OI-85, 2-OI-92B, 2-ARP-9-5A, 2-SR-3.1.3.5(A) | ||
2-OI-85, 2-OI-92B, 2-ARP-9-5A, 2-SR-3.1.3.5(A) | VALIDATIONTIME: 16 min PERFORMANCE TIME: | ||
VALIDATIONTIME: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 39 Exam IC 282 | |||
* Reset to IC-39 to ~ 30% Reactor Power | |||
* Open Schedule File: NRC JPM C U2 -RBM APRM Fail Console Operator Downscale.sch Instructions | |||
* Open Event File: NRC JPM C U2 -RBM APRM Fail Downscale.evt Malfunctions Description Event Severity Delay Initial set NM07L3233C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-33-C NM07L4025B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-25-B NM07L4033D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-33-D NM07L0817B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-17-B NM07L4017B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-17-B NM07L4041D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-41-D NM07L4049B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-49-B NM07L4057B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-57-B NM07L4817C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-17-C NM07L4825C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-25-C NM07L4833A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-33-A NM07L4841A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-41-A NM07L4849C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-49-C NM07L0825B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-25-B 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
NM07L0833D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-33-D NM07L0841D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-41-D NM07L0849B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-49-B NM07L2409B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-09-B NM07L2417D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-17-D NM07L2425D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-25-D NM07L2433B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-33-B NM07L2449D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-49-D NM07L2457D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-57-D NM07L1617C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-17-C NM07L1625C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-25-C NM07L1633A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-33-A NM07L1641A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-41-A NM07L1649C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-49-C NM07L1657C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-57-C NM07L1609A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-09-A NM07L3209C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-09-C NM07L3217A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-17-A NM07L3225A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-25-A NM07L3249A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-49-A NM07L3257A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-57-A NM07L4009D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-09-D NM07L4809A LPRM AMPLIFIER 15 0 N/A N/A 5 | |||
Schedule File: NRC JPM C U2 | Job Performance Measure (JPM) | ||
-RBM APRM Fail Downscale. | FAILURE 48-09-A NM07L5617D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-17-D NM07L5633B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-33-B NM07L5641B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-41-B NM07L3241C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-41-C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLO4631LGREENT(1) Control Rod 46-31 15 0 N/A N/A GREEN INDICATION Schedule File(s): | ||
Event File: NRC JPM C U2 -RBM APRM Fail Downscale.evt; <TRIGGER id="15" description="APRM Ch 2 Fail Downscale">ZLO4631LGREENT(1) == 0</TRIGGER> | |||
Schedule File: NRC JPM C U2 -RBM APRM Fail Downscale.sch 6 | |||
INITIAL CONDITIONS: | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
You are an Operator on Unit | INITIAL CONDITIONS: | ||
You are an Operator on Unit 2. | |||
-SR-3.1.3.5(A) completed through group 57. | * The Reactor is at 30% power | ||
No Control Rods are Fast Notching INITIATING CUES | * Startup Sequence Control Rod Movement Data Sheet 2-SR-3.1.3.5(A) completed through group 57. | ||
: | * No Control Rods are Fast Notching INITIATING CUES: | ||
The US has directed you to raise Reactor Power to 40% per 2 | The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14-31. | ||
-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14 | 7 | ||
-31. | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
Critical Step | Critical Step | ||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40. | |||
SAT UNSAT N/A | SAT Standard: | ||
[2] IF selected control rod has been identified as a | UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | ||
-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2 | Step 2: | ||
-HS | [2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT | ||
Standard: | * THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A) | ||
Determines that step in | N/A Standard: | ||
Determines that step in N/A Step 3: | |||
[3] OBSERVE the following for the selected control rod: | [3] OBSERVE the following for the selected control rod: | ||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED 8 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
[ | STEP / STANDARD SAT / UNSAT Step 4: | ||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 5: | |||
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | Critical Step | ||
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 6: | |||
Critical Step | |||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
9 | |||
Job Performance Measure (JPM) | |||
-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2 | STEP / STANDARD SAT / UNSAT Step 7: | ||
-HS | [2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT | ||
Standard: | * THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A) | ||
Determines that step in | N/A Standard: | ||
Determines that step in N/A Step 8: | |||
[3] OBSERVE the following for the selected control rod: | [3] OBSERVE the following for the selected control rod: | ||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the correct ROD GROUP when the Rod Worth Minimizer is enforcing Standard: | * White light on the Full Core Display ILLUMINATED SAT | ||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 9: | |||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing 10 | |||
SAT UNSAT | Job Performance Measure (JPM) | ||
[ | STEP / STANDARD SAT / UNSAT Step 10: | ||
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | Critical Step | ||
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 11: | |||
Critical Step | |||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
Step 12: | |||
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT | |||
* THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A) | |||
N/A Standard: | |||
Determines that step in N/A 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 13: | |||
[3] OBSERVE the following for the selected control rod: | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | N/A VERIFIES | ||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the correct ROD GROUP when the Rod Worth Minimizer is enforcing Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 14: | |||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 15: | |||
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | [5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | ||
[6] OBSERVE the control rod settles into the desired position and the ROD SETTLE light extinguishes. | Critical Step | ||
Standard: | [6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | ||
PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | UNSAT Standard: | ||
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 12 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Note to Examiner: This begins the Alternate Path section of JPM Simulator Booth Operator: Insert Event Trigger #1 to fail APRM 2 Downscale. | |||
Step 16: | |||
APRM Sensor/Trip Point: | |||
DOWNSCALE/ | |||
APRM Downscale: <= 5% | |||
OPRM INOP OPRM Inop: Less than 23 operable cells 4 | |||
Sensor Location: | Sensor Location: | ||
Control Room Panel 2-9-14. Probable Cause: | Control Room Panel 2-9-14. | ||
Probable Cause: | |||
A. Unbypassed APRM channel at or below sensor set point. | |||
B. SI or SR in progress. | B. SI or SR in progress. | ||
C. Unit shutdown (Mode 3 or 4). | C. Unit shutdown (Mode 3 or 4). Critical Step D. Failed sensor. | ||
D. Failed sensor. | SAT Automatic Action: UNSAT A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only) | ||
Automatic Action: A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only) | N/A Operator Action: | ||
Operator Action: A. DETERMINE which APRM/OPRM channel is downscale/inop. | A. DETERMINE which APRM/OPRM channel is downscale/inop. | ||
B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 2-OI-92B. | B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 2-OI-92B. | ||
13 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 16(continued) | |||
CONTROL ROD Sensor/Trip Point: | |||
WITHDRAWAL Relays: 3A-K1 Nuclear Instrumentation BLOCK 3A-K2 Refuel Equipment in Use High Level in Scram Discharge 7 Volume Scram Discharge Volume High Water Level Bypass Rx Mode Switch in SHUTDOWN PRNM (ANY APRM OPRM or RBM) | |||
Sensor/Trip Point: | Sensor Location: | ||
Relays: | Panel 2-9-28 Elevation 593' Aux Instr Room Probable Cause: | ||
A. One or more sensors at or above set point. | |||
Panel 2-9-28 Elevation 593' Aux Instr Room Probable Cause: | |||
B. Malfunction of sensor. | B. Malfunction of sensor. | ||
C. Control rod drop accident Automatic Action: Rod withdrawal block Operator Action: | C. Control rod drop accident Automatic Action: | ||
Rod withdrawal block Operator Action: | |||
A. DETERMINE initiating condition from corresponding rod withdrawal block alarm(s) and REFER TO operator action for alarm(s). | |||
Standard: | |||
Reference 2-ARP-9-5A and identifies APRM Ch 2 is down scale and proceeds to bypass APRM Ch 2 per 2-OI-92B CUE: Respond as stated in Alarm Response Instruction and Bypass APRM Ch 2 per 3-OI-92B. | |||
14 | |||
Job Performance Measure (JPM) | |||
APRM/OPRM Channel | STEP / STANDARD SAT / UNSAT Step 17: | ||
NOTES | |||
: 1) Only one APRM/OPRM in each trip system can be bypassed at a time. | |||
: 2) All operations are performed on Panel 2-9-5 unless specifically stated otherwise. | |||
: 3) In order to prevent inadvertent rod withdrawal block or Reactor scram while operating APRM BYPASS selector switch, Verify that the BLUE BYPASSED lights on Panel 9-14 Voters are extinguished prior to selecting any other channel to be bypassed. After bypassing a channel, the applicable BLUE BYPASSED status lights on Panel 9-14 Voters are required to be illuminated prior to testing, operating, or working on that channel. SAT UNSAT 6.1 Bypassing APRM/OPRM Channel N/A CAUTION | |||
[QA/C] SPP-10.4 requires approval of the Plant Manager or his designee prior to any planned operation with APRMs bypassed unless bypassing is specifically allowed within approved procedures. | |||
[ISE-HPS-92-RO1] | |||
[1] REVIEW all precautions and limitations. REFER TO Section 3.0. | [1] REVIEW all precautions and limitations. REFER TO Section 3.0. | ||
Standard: | Standard: | ||
Demonstrates reviewing precautions and limitations section 3.0. | |||
[2] PLACE APRM BYPASS, 2-HS-92-7B/S3, to desired channel to be bypassed. | Step 18: | ||
Standard: | Critical Step | ||
[2] PLACE APRM BYPASS, 2-HS-92-7B/S3, to desired channel to be bypassed. SAT Standard: UNSAT PLACE APRM BYPASS, 2-HS-92-7B/S3, to APRM CH 2 N/A 15 | |||
Job Performance Measure (JPM) | |||
Required During and Following Control Rod Withdrawal (continued) | STEP / STANDARD SAT / UNSAT Step 19: | ||
[6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN | [3] CHECK BLUE BYPASSED lights illuminated on Panel 2-9-14 Voters. SAT Standard: UNSAT Observes BLUE BYPASS light illuminated on Panel 2-9-14 for N/A APRM CH 2. | ||
Step 20: | |||
[4] VERIFY white bypass light on Panel 2-9-5 is illuminated. SAT Standard: UNSAT Observes WHITE BYPASS light illuminated on Panel 2-9-5. N/A Note to Examiner: If needed, cue student to proceed with actions required to continue rod movements. Student may continue at step 21 or 24. | |||
Step 21: | |||
6.6.2 Actions Required During and Following Control Rod Withdrawal (continued) | |||
[6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN SAT PERFORM the following at the Unit Supervisors discretion to UNSAT REINITIALIZE the RBM: | |||
N/A | |||
[6.1] PLACE CRD POWER, 2-HS-85-46 in the OFF position to deselect the Control Rod. | [6.1] PLACE CRD POWER, 2-HS-85-46 in the OFF position to deselect the Control Rod. | ||
Standard: | Standard: | ||
CRD POWER, 2-HS-85-46 in the OFF position. | |||
16 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 22: | |||
SAT | |||
[6.2] PLACE CRD POWER, 2-HS-85-46, in the ON position. | |||
UNSAT Standard: | |||
N/A PLACED CRD POWER, 2-HS-85-46, in the ON position. | |||
Step 23: | |||
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and SAT PERFORM applicable section for Control Rod withdrawal. | |||
UNSAT Standard: | |||
N/A Continues with Control Rod Movement CUE: Proceed with Control Rod Movement. | |||
Step 24: | |||
Critical Step | |||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
17 | |||
Job Performance Measure (JPM) | |||
Job Performance Measure (JPM) | STEP / STANDARD SAT / UNSAT Step 25: | ||
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT | |||
* | * THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A) | ||
N/A Standard: | |||
Determines that step in N/A Step 26: | |||
[3] OBSERVE the following for the selected control rod: | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 27: | |||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing 18 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 28: | |||
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Termination Criteria: When Control Rod is at position 04, state End of Task STOP TIME: | |||
19 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit | You are an Operator on Unit 2. | ||
* The Reactor is at 30% power | |||
-SR-3.1.3.5(A) completed through group 57. | * Startup Sequence Control Rod Movement Data Sheet 2-SR-3.1.3.5(A) completed through group 57. | ||
INITIATING CUES: | |||
INITIATING CUES | The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14-31. | ||
: | 20 | ||
The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14 | |||
-31. | |||
Job Performance Measure (JPM) | |||
LOSS OF REFERENCE APRM TO ROD BLOCK SITE: BFN JPM TITLE: | |||
MONITOR JPM NUMBER: 672A U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-085-AL-03 RESPOND TO CONTROL ROD TASK NUMBER / TASK TITLE(S): | |||
WITHDRAWL BLOCK K/A RATINGS: RO: 3.1 SRO: 3.3 215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures K/A No. &STATEMENT: | |||
to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR-3,4,5 RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 7 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _672A U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to bypass an APRM Channel and clear a Control Rod Block from Rod Block Monitoring System. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 3-OI-85, 3-OI-92B, 3-ARP-9-5A, 3-SR-3.1.3.5(A) | ||
3-OI-85, 3-OI-92B, 3-ARP-9-5A, 3-SR-3.1.3.5(A) | VALIDATIONTIME: | ||
VALIDATIONTIME: | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 04/30/15 All Initial issue 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 39 Exam IC 282 | |||
* Reset IC-39to ~ 30% Reactor Power | |||
* Open Schedule File: NRC JPM C U3 -RBM APRM Fail Console Operator Downscale.sch Instructions | |||
* Open Event File: NRC JPM C U3 -RBM APRM Fail Downscale.evt Malfunctions Description Event Severity Delay Initial set NM07L3233C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-33-C NM07L4025B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-25-B NM07L4033D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-33-D NM07L0817B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-17-B NM07L4017B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-17-B NM07L4041D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-41-D NM07L4049B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-49-B NM07L4057B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-57-B NM07L4817C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-17-C NM07L4825C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-25-C NM07L4833A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-33-A NM07L4841A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-41-A NM07L4849C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-49-C NM07L0825B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-25-B 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
NM07L0833D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-33-D NM07L0841D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-41-D NM07L0849B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-49-B NM07L2409B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-09-B NM07L2417D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-17-D NM07L2425D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-25-D NM07L2433B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-33-B NM07L2449D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-49-D NM07L2457D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-57-D NM07L1617C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-17-C NM07L1625C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-25-C NM07L1633A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-33-A NM07L1641A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-41-A NM07L1649C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-49-C NM07L1657C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-57-C NM07L1609A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-09-A NM07L3209C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-09-C NM07L3217A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-17-A NM07L3225A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-25-A NM07L3249A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-49-A NM07L3257A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-57-A NM07L4009D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-09-D NM07L4809A LPRM AMPLIFIER 15 0 N/A N/A 5 | |||
Schedule File: NRC JPM C U3 | Job Performance Measure (JPM) | ||
-RBM APRM Fail Downscale. | FAILURE 48-09-A NM07L5617D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-17-D NM07L5633B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-33-B NM07L5641B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-41-B NM07L3241C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-41-C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLO4631LGREENT(1) Control Rod 46-31 15 0 N/A N/A GREEN INDICATION Schedule File(s): | ||
Event File: NRC JPM C U3 -RBM APRM Fail Downscale.evt; <TRIGGER id="15" description="APRM Ch 2 Fail Downscale">ZLO4631LGREENT(1) == 0</TRIGGER> | |||
Schedule File: NRC JPM C U3 -RBM APRM Fail Downscale.sch 6 | |||
INITIAL CONDITIONS: | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is at 30% power | |||
* Startup Sequence Control Rod Movement Data Sheet 3-SR-3.1.3.5(A) completed through group 58. | |||
INITIATING CUES: | |||
The US has directed you to raise Reactor Power to 40% per 3-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 59; Control Rod 22-39. | |||
7 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
Job Performance Measure (JPM) | |||
Critical Step | Critical Step | ||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
Step 2: | |||
[2] OBSERVE the following for the selected control rod: | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 3: | |||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing 8 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 4: | |||
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 5: | |||
Critical Step | |||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
Step 6: | |||
[2] OBSERVE the following for the selected control rod: | [2] OBSERVE the following for the selected control rod: | ||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED 9 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
[ | STEP / STANDARD SAT / UNSAT Step 7: | ||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 8: | |||
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 9: | |||
Critical Step | Critical Step | ||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
10 | |||
SAT UNSAT | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 10: | |||
[2] OBSERVE the following for the selected control rod: | [2] OBSERVE the following for the selected control rod: | ||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
-HS-85-48, in ROD OUT NOTCH, and RELEASE | * White light on the Full Core Display ILLUMINATED SAT | ||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 11: | |||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 12: | |||
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | Critical Step | ||
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Note to Examiner: This begins the Alternate Path section of JPM Simulator Booth Operator: Insert Event Trigger #1 to fail APRM 2 Downscale. | |||
Step 13: | |||
APRM Sensor/Trip Point: | |||
DOWNSCALE/ | |||
APRM Downscale: <= 5% | |||
OPRM INOP OPRM Inop: Less than 23 operable cells 4 | |||
This begins the Alternate Path section of JPM Simulator Booth Operator: | |||
Step 13: | |||
APRM Downscale: <=5% | |||
Sensor Location: | Sensor Location: | ||
Control Room Panel 3 14. Probable Cause: | Control Room Panel 3-9-14. | ||
Probable Cause: | |||
A. Unbypassed APRM channel at or below sensor set point. | |||
B. SI or SR in progress. | B. SI or SR in progress. | ||
C. Unit shutdown (Mode 3 or 4). | C. Unit shutdown (Mode 3 or 4). Critical Step D. Failed sensor. | ||
D. Failed sensor. | SAT Automatic Action: UNSAT A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only) | ||
Automatic Action: A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only) | N/A Operator Action: | ||
Operator Action: A. DETERMINE which APRM/OPRM channel is downscale/inop. | A. DETERMINE which APRM/OPRM channel is downscale/inop. | ||
B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 3-OI-92B. | B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 3-OI-92B. | ||
12 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 13(continued) | |||
CONTROL ROD Sensor/Trip Point: | |||
WITHDRAWAL Relays:3A-K1 Nuclear Instrumentation BLOCK 7 3A-K2 Refuel Equipment in Use High Level in Scram Discharge Volume Scram Discharge Volume High Water Level Bypass Rx Mode Switch in SHUTDOWN PRNM (ANY APRM OPRM or RBM) | |||
Sensor Location: | |||
Panel 3-9-28 Elevation 593' Aux Instr Room Probable Cause: | |||
A. One or more sensors at or above set point. | |||
B. Malfunction of sensor. | |||
C. Control rod drop accident Automatic Action: | |||
Rod withdrawal block Operator Action: | |||
A. DETERMINE initiating condition from corresponding rod withdrawalblock alarm(s) and REFER TO operator action for alarm(s). | |||
Standard: | |||
Reference 3-ARP-9-5A and identifies APRM Ch 2 is down scale and proceeds to bypass APRM Ch 2 per 3-OI-92B CUE:Respond as stated in Alarm Response Instruction and Bypass APRM Ch 2 per 3-OI-92B. | |||
13 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 14: | |||
NOTES | |||
: 1) Only one APRM/OPRM in each trip system can be bypassed at a time. | |||
Panel 3-9- | : 2) All operations are performed on Panel 3-9-5 unless specifically stated otherwise. | ||
: 3) In order to prevent inadvertent rod withdrawal block or Reactor scram while operating APRM BYPASS selector switch, Verify that the BLUE BYPASSED lights on Panel 9-14 Voters are extinguished prior to selecting any other channel to be bypassed. After bypassing a channel, the applicable BLUE BYPASSED status lights on Panel 9-14 Voters are required to be illuminated prior to testing, operating, or working on that channel. SAT UNSAT 6.1 Bypassing APRM/OPRM Channel N/A CAUTION | |||
[QA/C] SPP-10.4 requires approval of the Plant Manager or his designee prior to any planned operation with APRMs bypassed unless bypassing is specifically allowed within approved procedures. | |||
[ISE-HPS-92-RO1] | |||
APRM/OPRM Channel | |||
[1] REVIEW all precautions and limitations. REFER TO Section 3.0. | [1] REVIEW all precautions and limitations. REFER TO Section 3.0. | ||
Standard: | Standard: | ||
PLACE APRM BYPASS, 3 | Demonstrates reviewing precautions and limitations section 3.0. | ||
-HS-92-7B/S3, to APRM CH 2 | CUE: If asked per note 2 above, Panel 9-14 Voter BLUE LIGHTS are extinguished. | ||
Step 15: | |||
Critical Step | |||
[2] PLACE APRM BYPASS, 3-HS-92-7B/S3, to desired channel to be bypassed. SAT Standard: UNSAT PLACE APRM BYPASS, 3-HS-92-7B/S3, to APRM CH 2 N/A 14 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 16: | |||
[3] CHECK BLUE BYPASSED lights illuminated on Panel 3-9-14 Voters. SAT Standard: UNSAT Simulates observing BLUE BYPASS light illuminated on Panel 3- N/A 9-14 for APRM CH 2. | |||
Cue: Blue Light is illuminated on Panel 3-9-14 for APRM CH 2. | |||
Step 17: | |||
Job Performance Measure (JPM) | [4] VERIFY white bypass light on Panel 3-9-5 is illuminated. SAT Standard: UNSAT Observes WHITE BYPASS light illuminated on Panel 3-9-5. N/A Note to NRC Examiner: If needed, cue student to proceed with actions required to continue rod movements.Student may continue at step 18 or 21. | ||
Simulates observing BLUE BYPASS light illuminated on Panel 3 14 for APRM CH 2 | Step 18: | ||
6.6.2 Actions Required During and Following Control Rod Withdrawal (continued) | |||
Step | [6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN SAT PERFORM the following at the Unit Supervisors discretion to UNSAT REINITIALIZE the RBM: | ||
[4] VERIFY white bypass light on Panel 3 5 is illuminated. | N/A | ||
[6.1] PLACE CRD POWER, 3-HS-85-46 in the OFF position to deselect the Control Rod. | |||
Standard: | Standard: | ||
CRD POWER, 3-HS-85-46 in the OFF position. | |||
15 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 19: | |||
SAT | |||
[6.2] PLACE CRD POWER, 3-HS-85-46, in the ON position. | |||
UNSAT Standard: | |||
N/A PLACED CRD POWER, 3-HS-85-46, in the ON position. | |||
Step 20: | |||
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and SAT PERFORM applicable section for Control Rod withdrawal. | |||
-HS-85-46, in the ON position. | UNSAT Standard: | ||
Standard: | N/A Continues with Control Rod Movement Cue:If asked,Proceed with Control Rod Movement. | ||
Step 21: | |||
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and PERFORM applicable section for Control Rod withdrawal. | Critical Step | ||
Standard: | [1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40. | ||
Continues with Control Rod Movement | SAT Standard: | ||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
16 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 22: | |||
[2] OBSERVE the following for the selected control rod: | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * White light on the Full Core Display ILLUMINATED SAT | ||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the correct ROD GROUP when the Rod Worth Minimizer is enforcing Standard: | * Rod Out Permit light ILLUMINATED UNSAT Standard: | ||
-HS-85-48, in ROD OUT NOTCH, and RELEASE. | N/A VERIFIES | ||
[5] OBSERVE the control rod settles into the desired position and the ROD SETTLE light extinguishes. | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
Standard: | * White light on the Full Core Display ILLUMINATED | ||
PLACED CRD CONTROL SWITCH, 3 48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | * Rod Out Permit light ILLUMINATED Step 23: | ||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 24: | |||
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Termination Criteria: When Control Rod is at position 04, state End of Task STOP TIME: | |||
17 | |||
Job Performance Measure (JPM) | |||
Job Performance Measure (JPM) | Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | ||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is at 30% power | |||
** | * Startup Sequence Control Rod Movement Data Sheet 3-SR-3.1.3.5(A) completed through group 58. | ||
INITIATING CUES: | |||
The US has directed you to raise Reactor Power to 40% per 3-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 59; Control Rod 22-39. | |||
18 | |||
Job Performance Measure (JPM) 2-EOI APPENDIX-6E INJECTION SUBSYSTEM LINEUP SITE: BFN JPM TITLE: | |||
CS SYSTEM II JPM NUMBER: 257A U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-35/ Lineup Injection Subsystem-Core TASK NUMBER / TASK TITLE(S): Spray Loop I(II) in Accordance with EOI Appendix 6D(E) | |||
K/A RATINGS: RO: 3.9 SRO: 3.9 209001 Low Pressure Core Spray SystemA4.08 Ability to K/A No. &STATEMENT: manually operate and/or monitor in thecontrol room: Reactor water level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 2 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Job Performance Measure (JPM) | Site Training Program Owner Date 1 | ||
2-EOI APPENDIX | |||
-6E INJECTION SUBSYSTEM LINEUP CS SYSTEM II JPM NUMBER: | |||
SRO STA UO NAUO | |||
-Core Spray Loop I(II) in Accordance with EOI Appendix 6D(E) K/A RATINGS: | |||
RO: | |||
209001 Low Pressure Core Spray SystemA4.08 Ability to manually operate and/or monitor in thecontrol room: Reactor water level RELATED PRA INFORMATION: | |||
Risk Significant SAFETY FUNCTION: | |||
2 | |||
In-Plant | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _257A U2_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to identify and corrects Inboard and Outboard Injection Valve lineup in order to inject water into the RPV with Core Spray System II to recover level Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-EOI APPENDIX-6E VALIDATIONTIME: 8 min PERFORMANCE TIME: | ||
2-EOI APPENDIX-6E VALIDATIONTIME: 8 min | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 12/06/10 All Initial issue 1 04/27/15 All General revision & re-format 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 283 | |||
: 1. Open Schedule File | : 1. Open Schedule File | ||
: 2. Open Event File | : 2. Open Event File | ||
: 3. Reset to IC-28and take out of freeze | : 3. Reset to IC-28and take out of freeze. | ||
: 4. CLOSE 2-FCV-75-51 Console | |||
: 5. OPEN 2-FCV-75-53 Operator | |||
: 6. Man Scram Rx and place MS to SD. | |||
Instructions | |||
: 7. Open 6 ADS Valves. | |||
: 8. Wait until various alarms with Supp Pool Temp High come in to save IC. | |||
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 15 75% 5 Yes INSIDE DRYWELL CS04A CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV II CS02B CS INBOARD 15 N/A N/A Yes INJECTION VALVE AUTO OPENING FAILURE (FCV 53) | |||
RH06A RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV I RH06B RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV II RC01 RCIC TURBINE TRIP 15 N/A N/A Yes SYSTEM FAILURE HP04 HPCI STEAM 15 N/A N/A Yes SUPPLY VALVE AUTO OPENING FAILURE FW01A CONDENSATE 15 N/A 10 Yes PUMP TRIP 2A 4 | |||
Event File(s): JPM 257A U2 Core Spray Alt Inj.evt | Job Performance Measure (JPM) | ||
FW01B CONDENSATE 15 N/A 10 Yes PUMP TRIP 2B FW01C CONDENSATE 15 N/A 10 Yes PUMP TRIP 2C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): JPM 257A U2 Core Spray Alt Inj.sch Event File(s): JPM 257A U2 Core Spray Alt Inj.evt 5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
is complete" and I will acknowledge that your task is complete. | INITIAL CONDITIONS: | ||
You are an Operator on Unit 2. | |||
INITIAL CONDITIONS: | * The Reactor is Shutdown | ||
* RPV Water Level is lowering slowly. | |||
You are an Operator on Unit | * 1-EOI-1 has been entered and followed to RC-L6. | ||
INITIATING CUES: | |||
1-EOI-1 has been entered and followed to RC | The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above | ||
-L6. INITIATING CUES | (-)162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. | ||
6 | |||
-6E, Injection Subsystems Lineup Core Spray System II. | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
Location: Unit 2 Control Room Attachments: 1. NPSH Monitoring | |||
[1] VERIFY OPEN the following valves: | [1] VERIFY OPEN the following valves: | ||
2-FCV-75-30, CORE SPRAY PUMP 2B SUPPR POOL SUCT VLV | SAT | ||
[1] (continued)VERIFY OPEN the following valves: | * 2-FCV-75-30, CORE SPRAY PUMP 2B SUPPR POOL SUCT UNSAT VLV | ||
2-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. | * 2-FCV-75-39, CORE SPRAY PUMP 2D SUPPR POOL SUCT N/A VLV Standard: | ||
Verifies2-FCV-75-30 and 2-FCV-75-39 are open. | |||
Step 2: | |||
[1] (continued)VERIFY OPEN the following valves: Critical Step | |||
* 2-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. SAT UNSAT Standard: | |||
N/A Recognizes 2-FCV-75-51 is closed and 2-FCV-75-53 is open, valve closes 2-FCV-75-53 and Opens 2-FCV-75-51. | |||
Note to Examiner: Student will realignper OPDP-8 Conduct of Ops or OI-75, Core Spray System line up. | |||
7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 3: | |||
[2] VERIFY CLOSED 2-FCV-75-50, CORE SPRAY SYS II SAT TESTVALVE. | |||
UNSAT Standard: | |||
N/A Verifies 2-FCV-75-50 closed Step 4: | |||
Critical Step | |||
Job Performance Measure (JPM) | |||
Standard: | |||
[3] VERIFY CS Pump 2B and/or 2D running. | [3] VERIFY CS Pump 2B and/or 2D running. | ||
Standard: | SAT Standard: | ||
UNSAT Starts Core Pumps 2B and/or 2D N/A (Only starting one pump is Critical, the second pump is optional). | |||
Step 6: | |||
[4] WHEN RPV pressure is below 450 psig, THEN Critical Step THROTTLE2-FCV-75-53, CORE SPRAY SYS II INBDINJECT VALVE, SAT as necessary to control injection at or below4000 gpm per pump. | |||
[4] WHEN RPV pressure is below 450 psig, THEN | UNSAT Standard: | ||
Standard: | N/A Verifies pressure < 450 psig and opens 2-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or | ||
<8000 gpm for 2 pumps). | <8000 gpm for 2 pumps). | ||
Step 7: | |||
CAUTION Continuous operation with inadequate NPSH may result in pump damage or pump inoperability. | |||
SAT | |||
[5] MONITOR Core Spray Pump NPSH using Attachment 1. | [5] MONITOR Core Spray Pump NPSH using Attachment 1. | ||
Standard: Operator comparesCore Spray Pump flow rate with Suppression Pool temperature and Suppression Pool pressure and Determined adequate NPSH. | UNSAT Standard: | ||
Operator comparesCore Spray Pump flow rate with Suppression N/A Pool temperature and Suppression Pool pressure and Determined adequate NPSH. | |||
Termination Criteria: Once rector Water Level is > TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure. | |||
STOP TIME: | STOP TIME: | ||
8 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit 2. | |||
You are an Operator on Unit | * The Reactor is Shutdown | ||
* RPV Water Level is lowering slowly. | |||
1-EOI-1 has been entered and followed to RC | * 1-EOI-1 has been entered and followed to RC-L6. | ||
-L6. | INITIATING CUES: | ||
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above 162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. | |||
INITIATING CUES | 9 | ||
: | |||
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above 162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix | |||
-6E, Injection Subsystems Lineup Core Spray System II. | |||
Job Performance Measure (JPM) 3-EOI APPENDIX-6E INJECTION SUBSYSTEM LINEUP SITE: BFN JPM TITLE: | |||
CS SYSTEM II JPM NUMBER: 257A U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-35/ Lineup Injection Subsystem-Core TASK NUMBER / TASK TITLE(S): Spray Loop I(II) in Accordance with EOI Appendix 6D(E) | |||
K/A RATINGS: RO: 3.9 SRO: 3.9 209001 Low Pressure Core Spray System A4.08 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor water level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 2 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _257A U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to identify and corrects Inboard and Outboard Injection Valve lineup in order to inject water into the RPV with Core Spray System II to recover level Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 3-EOI APPENDIX-6E VALIDATIONTIME: 5 min PERFORMANCE TIME: | ||
3-EOI APPENDIX-6E VALIDATIONTIME: 5 min | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 12/06/10 All Initial issue 1 04/27/15 All General revision & re-format 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 283 | |||
: 1. Open Schedule File | : 1. Open Schedule File | ||
: 2. Open Event File | : 2. Open Event File | ||
: 3. Reset to IC | : 3. Reset to IC-28 and take out of freeze. | ||
-28 and take out of freeze. | : 4. CLOSE 2-FCV-75-51 Console | ||
: 4. CLOSE 2-FCV-75-51 5. OPEN 2-FCV-75-53 6. Man Scram Rx and place MS to SD. 7. Open 6 ADS Valves. | : 5. OPEN 2-FCV-75-53 Operator | ||
: 8. Wait until various alarms with Supp Pool Temp High come in to save IC. | : 6. Man Scram Rx and place MS to SD. | ||
Instructions | |||
: 7. Open 6 ADS Valves. | |||
: 8. Wait until various alarms with Supp Pool Temp High come in to save IC. | |||
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 15 75% 5 Yes INSIDE DRYWELL CS04A CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV II CS02B CS INBOARD 15 N/A N/A Yes INJECTION VALVE AUTO OPENING FAILURE (FCV 53) | |||
RH06A RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV I RH06B RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV II RC01 RCIC TURBINE TRIP 15 N/A N/A Yes SYSTEM FAILURE HP04 HPCI STEAM 15 N/A N/A Yes SUPPLY VALVE AUTO OPENING FAILURE FW01A CONDENSATE 15 N/A 10 Yes PUMP TRIP 3A 4 | |||
Event File(s): JPM 257A U3 Core Spray Alt Inj.evt | Job Performance Measure (JPM) | ||
FW01B CONDENSATE 15 N/A 10 Yes PUMP TRIP 3B FW01C CONDENSATE 15 N/A 10 Yes PUMP TRIP 3C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): JPM 257A U3 Core Spray Alt Inj.sch Event File(s): JPM 257A U3 Core Spray Alt Inj.evt 5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit 3. | |||
You are an Operator on Unit | * The Reactor is Shutdown | ||
* RPV Water Level is lowering slowly. | |||
1-EOI-1 has been entered and followed to RC | * 1-EOI-1 has been entered and followed to RC-L6. | ||
-L6. INITIATING CUES | INITIATING CUES: | ||
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above | |||
-6E, Injection Subsystems Lineup Core Spray System II. | (-)162 inches (TAF) using Core Spray System II as directed by 3-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. | ||
6 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
Location: Unit 3 Control Room Attachments: 1. NPSH Monitoring | |||
[1] VERIFY OPEN the following valves: | [1] VERIFY OPEN the following valves: | ||
3-FCV-75-30, CORE SPRAY PUMP 3B SUPPR POOL SUCT VLV | SAT | ||
* 3-FCV-75-30, CORE SPRAY PUMP 3B SUPPR POOL SUCT UNSAT VLV | |||
* 3-FCV-75-39, CORE SPRAY PUMP 3D SUPPR POOL SUCT N/A VLV Standard: | |||
Verifies3-FCV-75-30 and 3-FCV-75-39 are open. | |||
Step 2: | |||
Critical Step | |||
[1] (continued) VERIFY OPEN the following valves: | [1] (continued) VERIFY OPEN the following valves: | ||
3-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. | * 3-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. | ||
SAT UNSAT Standard: | |||
N/A Recognizes 3-FCV-75-51 is closed and 3-FCV-75-53 is open, closes 3-FCV-75-53 and Opens 3-FCV-75-51. | |||
Note to Examiner: Student will realignper OPDP-8 Conduct of Ops or OI-75, Core Spray System line up. | |||
7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 3: | |||
[2] VERIFY CLOSED 3-FCV-75-50, CORE SPRAY SYS II TEST SAT VALVE. | |||
UNSAT Standard: | |||
N/A Verifies 3-FCV-75-50 closed Step 4: | |||
Critical Step | |||
Job Performance Measure (JPM) | |||
-FCV-75-50 closed | |||
[3] VERIFY CS Pump 3B and/or 3D running. | [3] VERIFY CS Pump 3B and/or 3D running. | ||
Standard: | SAT Standard: | ||
UNSAT Starts Core Pumps 3B and/or 3D (Only starting one pump is N/A Critical, the second pump is optional). | |||
Step 6: | |||
[4] WHEN RPV pressure is below 450 psig, THEN Critical Step THROTTLE 3-FCV-75-53, CORE SPRAY SYS II INBDINJECT VALVE, SAT as necessary to control injection at or below4000 gpm per pump. | |||
Standard: | UNSAT Standard: | ||
-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or | N/A Verifies pressure < 450 psig and opens 3-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or | ||
<8000 gpm for 2 pumps). | <8000 gpm for 2 pumps). | ||
Step 7: | |||
CAUTION Continuous operation with inadequate NPSH may result in pump damage or pump inoperability. | |||
SAT | |||
[5] MONITOR Core Spray Pump NPSH using Attachment 1. | [5] MONITOR Core Spray Pump NPSH using Attachment 1. | ||
Standard: Operator compares Core Spray pump flow rate with Suppression Pool temperature and Suppression Pool pressure and Determined adequate NPSH. | UNSAT Standard: | ||
Operator compares Core Spray pump flow rate with Suppression N/A Pool temperature and Suppression Pool pressure and Determined adequate NPSH. | |||
Termination Criteria: Once rector Water Level is > TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure. | |||
TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure. | |||
STOP TIME: | STOP TIME: | ||
8 | |||
is complete" and I will acknowledge that your task is complete. | Job Performance Measure (JPM) | ||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is Shutdown | |||
* RPV Water Level is lowering slowly. | |||
* 1-EOI-1 has been entered and followed to RC-L6. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level using Core Spray System II as directed by 3-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. Directed level band is +2 to +51 inches. | |||
9 | |||
Job Performance Measure (JPM) 2-EOI Appendix-11F Alternate RPV Pressure Control SITE: BFN JPM TITLE: | |||
Systems: RFPT On Minimum Flow JPM NUMBER: 670A U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-58 Lineup Alternate RPV Pressure Control TASK NUMBER / TASK TITLE(S): Systems- RFPT on Minimum Flow IAW EOI Appendix 11F K/A RATINGS: RO: 3.6SRO: 3.6 239001 Main and Reheat Steam System A1.01 Ability to predict and/or monitor changes in parameters associated with K/A No. &STATEMENT: | |||
operating the MAIN ANDREHEAT STEAM SYSTEM controls including: Main steam pressure RELATED PRA INFORMATION: None SAFETY FUNCTION: 3 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _670A U2_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to necessary to place one RFPT in pressure control as directed by 2-EOI Appendix-11F. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | |||
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 2-EOI-APPENDIX-11F VERIFICATION TIME: 12 min PERFORMANCE TIME: | |||
COMMENTS: | |||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
JPM Number: | |||
TASK STANDARD: | |||
Perform operations necessary to necessary to place one RFPT in pressure control as directed by 2 | |||
-EOI Appendix | |||
-11F. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. PRA: NA REFERENCES/PROCEDURES NEEDED: | |||
Procedure: | |||
COMMENTS: | |||
Additional comment sheets attached? | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 284 Malfunctions Description Event Severity Delay Initial set fw15a SPURIOUS RFP 15 N/A 0 N/A BEARING LOW OIL PRESSURE tc03a-j Fail Bypass Valves 1 0% 0 N/A closed ad01e 20 SRV 1-31 stuck open 1 20% 0 N/A 20% | |||
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Initial Setup: | |||
: 1. Reset to IC 28 | : 1. Reset to IC 28 | ||
: 2. Manually Scram RX | : 2. Manually Scram RX | ||
: 3. Trip 2A and 2B RFPT | : 3. Trip 2A and 2B RFPT | ||
: 4. Run Schedule File: NRC JPM E U2 | : 4. Run Schedule File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | ||
-Alt RPV Press Control RFP Min Flow | |||
: 5. Insert Manual Trigger #1 | : 5. Insert Manual Trigger #1 | ||
: 6. After 2A RFPT Speed is <350 RPM Open Event File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | : 6. After 2A RFPT Speed is <350 RPM Open Event File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | ||
Line 1,262: | Line 1,324: | ||
: 8. Freeze simulator and save IC. | : 8. Freeze simulator and save IC. | ||
Schedule Files: | Schedule Files: | ||
: 1. NRC JPM E U2 | : 1. NRC JPM E U2-Alt RPV Press Control RFP Min Flow.sch | ||
-Alt RPV Press Control RFP Min Flow.sch 2. NRC JPM E U2 | : 2. NRC JPM E U2-Alt RPV Press Control RFP Min Flow RFPT Trip.evt 3 | ||
-Alt RPV Press Control RFP Min Flow RFPT Trip.evt | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 2C. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to place 2A RFPT in alternate pressure control, as directed by 2-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / UNSAT Step 1: | |||
[1] IF BOTH of the following exist: | |||
* Emergency RPV Depressurization is required, AND | |||
* Group 1 Isolation Signal exists, THEN SAT EXIT this procedure and ENTER EOI Appendix 11H. UNSAT N/A Standard: | |||
Job Performance Measure (JPM) | |||
Emergency RPV Depressurization is required, AND | |||
Standard: | |||
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | ||
Step 2: | |||
SAT | |||
[2] VERIFY MSIVs open. | |||
UNSAT Standard: | |||
N/A Verifies MSIVs OPEN 6 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 3: | |||
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. SAT Standard: UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 4: | |||
-7 in. Hg. Standard: | |||
Verifies Hotwell Pressure at or below | |||
-7 in. Hg | |||
[4] PLACE RFPTs in service as follows: | [4] PLACE RFPTs in service as follows: | ||
[4.1] VERIFY the following: | [4.1] VERIFY the following: | ||
[4.1.1] At least one condensate pump running. [4.1.2] At least one condensate booster pump running. [4.1.3] Condensate System aligned to supply suction toRFPs. | SAT | ||
Standard: | [4.1.1] At least one condensate pump running. | ||
[4.1.2] At least one condensate booster pump running. | |||
UNSAT | |||
[4.1.3] Condensate System aligned to supply suction toRFPs. | |||
N/A Standard: | |||
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | ||
Step 5: | |||
[4.2] VERIFY Main Oil Pump running for each RFPT to bestarted. | [4.2] VERIFY Main Oil Pump running for each RFPT to bestarted. SAT Standard: UNSAT Verifies main oil pump running for RFPT 2A N/A Step 6: | ||
Standard: | Critical Step | ||
Verifies main oil pump running for RFPT 2A | |||
[4.3] VERIFY CLOSED 2-FCV-3-19, RFP 2ADISCHARGE VALVE. | [4.3] VERIFY CLOSED 2-FCV-3-19, RFP 2ADISCHARGE VALVE. | ||
Standard: | SAT Standard: | ||
VERIFY CLOSED 2-FCV-3-19, RFP 2A DISCHARGE VALVE. | UNSAT VERIFY CLOSED 2-FCV-3-19, RFP 2A DISCHARGE VALVE. | ||
N/A 7 | |||
Standard: | |||
Depresses 2 | Job Performance Measure (JPM) | ||
-HS-46-8A | STEP / STANDARD SAT / UNSAT Step 7: | ||
[4.5] DEPRESS 2-HS-3-124A , RFPT 2A TRIP RESET. | Critical Step | ||
Standard: | [4.4] DEPRESS 2-HS-46-8A RFPT 2A SPEED CONT RAISE/LOWER, and VERIFY amber lightis illuminated. SAT Standard: UNSAT Depresses 2-HS-46-8A N/A Step 8: | ||
Depresses 2 | [4.5] DEPRESS 2-HS-3-124A, RFPT 2A TRIP RESET. Critical Step Standard: SAT Depresses 2-HS-3-124A and verifies the 2-Z1-1-123 LP Stop Valve and UNSAT 2-Z1-127 HP Stop Valve comes OPEN. | ||
-HS-3-124A and verifies the 2 | N/A Step 9: | ||
-Z1-1-123 LP Stop Valve and 2-Z1-127 HP Stop Valve comes OPEN. | Critical Step | ||
[4.6] PLACE 2-HS-46-112A RFPT 2A START/LOCAL ENABLE, in START. SAT Standard: UNSAT Places 2-HS-46-112A in START N/A Note to Examiner: | |||
[4.6] PLACE 2-HS-46-112A RFPT 2A START/LOCAL ENABLE, in START. Standard: | |||
Places 2-HS-46-112A in START | |||
RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10: | RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10: | ||
Critical Step | |||
[4.7] CHECK RFPT 2A speed increases to approximately 600 rpm. | [4.7] CHECK RFPT 2A speed increases to approximately 600 rpm. | ||
Standard: | SAT Standard: | ||
Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 2-EOI-APPENDIX-11F. | UNSAT Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 2-EOI-APPENDIX-11F. N/A CUE: | ||
-EOI-APPENDIX-11F. AO: Reports an oil leak of ~5 gpm on RFPT A bearings. | US: Proceed as directed per 2-EOI-APPENDIX-11F. | ||
Job Performance Measure (JPM) | AO: Reports an oil leak of ~5 gpm on RFPT A bearings. | ||
8 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 11: | |||
[1] IF BOTH of the following exist: | [1] IF BOTH of the following exist: | ||
Emergency RPV Depressurization is required, AND | * Emergency RPV Depressurization is required, AND | ||
* Group 1 Isolation Signal exists, THEN EXIT this procedure and ENTER SAT EOI Appendix 11H. | |||
Standard: | UNSAT Standard: N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | ||
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | Step 12: | ||
[2] VERIFY MSIVs open. SAT Standard: UNSAT Verifies MSIVs OPEN N/A 9 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 13: | |||
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. SAT Standard: UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 14: | |||
-7 in. Hg. Standard: | |||
Verifies Hotwell Pressure at or below | |||
-7 in. Hg | |||
[4] PLACE RFPTs in service as follows: | [4] PLACE RFPTs in service as follows: | ||
[4.1] VERIFY the following: | [4.1] VERIFY the following: | ||
[4.1.1] At least one condensate pump running. [4.1.2] At least one condensate booster pump running. [4.1.3] Condensate System aligned to supply suction toRFPs. | SAT | ||
Standard: | [4.1.1] At least one condensate pump running. | ||
[4.1.2] At least one condensate booster pump running. | |||
UNSAT | |||
[4.1.3] Condensate System aligned to supply suction toRFPs. | |||
N/A Standard: | |||
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | ||
Step 15: | |||
[4.2] VERIFY Main Oil Pump running for each RFPT to be started. Standard: | [4.2] VERIFY Main Oil Pump running for each RFPT to be started. SAT Standard: UNSAT Verifies main oil pump running for RFPT 2B N/A Step 16: | ||
Verifies main oil pump running for RFPT 2B | Critical Step | ||
[4.3] VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE. | [4.3] VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE. | ||
Standard: | SAT Standard: | ||
VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE. | UNSAT VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE. | ||
N/A 10 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 17: | |||
Critical Step | |||
[4.4] DEPRESS 2-HS-46-9A, RFPT 2BSPEED CONT RAISE/LOWER, and VERIFY amber light is illuminated. SAT Standard: UNSAT Depresses 2-HS-46-9A N/A Step 18: | |||
Critical Step | |||
[4.5] DEPRESS 2-HS-3-150A, RFPT 2B TRIP RESET. | |||
SAT Standard: | |||
UNSAT Depresses 2-HS-3-150A and verifies the 2-ZI-1-133 LP Stop Valve and 2-FCV-135 HP Stop Valve comes OPEN. N/A Step 19: | |||
Critical Step | |||
[4.6] PLACE 2-HS-46-138A, RFPT 2B START/LOCAL ENABLE, in START. SAT Standard: UNSAT Places 2-HS-46-138A in START N/A Step 20: | |||
[4.7] CHECK RFPT 2B speed increases to approximately 600 rpm. SAT Standard: UNSAT Verifies RFPT 2B speed increases to approximately 600 rpm N/A 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 21: | |||
[4.8] VERIFY OPEN 2-FCV-3-13, RFP2B MIN FLOW VALVE. SAT Standard: UNSAT Verifies 2-FCV-3-13 OPEN N/A Step 21: | |||
CAUTION RFP discharge pressure is limited to below 1250 psig to avoid system damage. | |||
[4.9] PLACE 2-HS-46-9A, RFPT 2B SPEED CONT RAISE/LOWER in Critical Step RAISE to raise RFPT speed, maintaining discharge pressure less than 1250 psig. SAT Standard: UNSAT Raises RFPT speed using Manual Speed Control Handswitch, N/A maintaining discharge pressure <1250 psig as indicated on 2-PI-3-9A RFPT 2B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable). | |||
STOP TIME END OF TASK 12 | |||
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. | Job Performance Measure (JPM) | ||
-4. Reactor water level control is in automatic on RFPT 2C. | Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | ||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 2C. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to place 2A RFPT in alternate pressure control, as directed by 2-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig. | |||
13 | |||
Job Performance Measure (JPM) 3-EOI Appendix-11F Alternate RPV Pressure Control SITE: BFN JPM TITLE: | |||
: | Systems: RFPT On Minimum Flow JPM 670A JPM NUMBER: REVISION: 0 U3 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-58 Lineup Alternate RPV Pressure Control TASK NUMBER / TASK TITLE(S): Systems- RFPT on Minimum Flow IAW EOI Appendix 11F K/A RATINGS: RO: 3.6 SRO: 3.6 239001 Main and Reheat Steam System A1.01 Ability to predict and/or monitor changes in parameters associated with K/A No. & STATEMENT: | ||
operating the MAIN AND REHEAT STEAM SYSTEM controls including: Main steam pressure RELATED PRA INFORMATION: None SAFETY FUNCTION: 3 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
- | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
OPERATOR: ________________________________ JPM Number: _______ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to necessary to place one RFPT in pressure control as directed by 3-EOI Appendix-11F. | |||
JPM Number: | |||
TASK STANDARD: | |||
Perform operations necessary to necessary to place one RFPT in pressure control as directed by 3 | |||
-EOI Appendix | |||
-11F. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 3-EOI-APPENDIX-11F VERIFICATION TIME: | ||
Procedure: | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
Additional comment sheets attached? | RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | ||
SIGNATURE: ___________________________ DATE: __________ | |||
RESULTS: SATISFACTORY ____ | EXAMINER 2 | ||
UNSATISFACTORY ____ | |||
(Retain entire JPM for records) | |||
SIGNATURE: ___________________________ | |||
DATE: __________ | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 284 Malfunctions Description Event Severity Delay Initial set fw15a SPURIOUS RFP 15 N/A 0 N/A BEARING LOW OIL PRESSURE tc03a-j Fail Bypass Valves 1 0% 0 N/A closed ad01e SRV 1-31 stuck open 1 26% 0 N/A Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set 3 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Initial Setup: | |||
: 1. Reset to IC 28 | : 1. Reset to IC 28 | ||
: 2. Manually Scram RX | : 2. Manually Scram RX | ||
: 3. Trip 2A and 2B RFPT | : 3. Trip 2A and 2B RFPT | ||
: 4. Run Schedule File: NRC JPM E U2 | : 4. Run Schedule File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | ||
-Alt RPV Press Control RFP Min Flow | |||
: 5. Insert Manual Trigger #1 | : 5. Insert Manual Trigger #1 | ||
: 6. After 2A RFPT Speed is <350 RPM Open Event File: NRC JPM E U2 | : 6. After 2A RFPT Speed is <350 RPM Open Event File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | ||
-Alt RPV Press Control RFP Min Flow | |||
: 7. Verify Auto Trigger #15 is ACTIVE | : 7. Verify Auto Trigger #15 is ACTIVE | ||
: 8. Freeze simulator and save IC. | : 8. Freeze simulator and save IC. | ||
Schedule Files: | Schedule Files: | ||
: 1. NRC JPM E U3 | : 1. NRC JPM E U3-Alt RPV Press Control RFP Min Flow.sch | ||
-Alt RPV Press Control RFP Min Flow.sch 2. NRC JPM E | : 2. NRC JPM E U3-Alt RPV Press Control RFP Min Flow RFPT Trip.evt 4 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/11/15 All Initial issue 5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
(OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | ||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. The Unit 3 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 3C. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to place 3A RFPT in alternate pressure control, as directed by 3-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig. | |||
6 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / UNSAT Step 1: | |||
[1] IF BOTH of the following exist: | |||
* Emergency RPV Depressurization is required, AND | |||
* Group 1 Isolation Signal exists, THEN EXIT this procedure and ENTER SAT EOI Appendix 11H. | |||
UNSAT Standard: N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | |||
Step 2: | |||
Job Performance Measure (JPM) | |||
Emergency RPV Depressurization is required, AND | |||
Standard: | |||
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | |||
[2] VERIFY MSIVs open. | [2] VERIFY MSIVs open. | ||
Standard: | SAT Standard: | ||
Verifies MSIVs OPEN | UNSAT Verifies MSIVs OPEN N/A 7 | ||
Job Performance Measure (JPM) | |||
-7 in. Hg. Standard: | STEP / STANDARD SAT / UNSAT Step 3: | ||
Verifies Hotwell Pressure at or below | [3] VERIFY Hotwell Pressure at or below -7 in. Hg. | ||
-7 in. Hg | SAT Standard: | ||
UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 4: | |||
[4] PLACE RFPTs in service as follows: | [4] PLACE RFPTs in service as follows: | ||
[4.1] VERIFY the following: | [4.1] VERIFY the following: | ||
[4.1.1] At least one condensate pump running. [4.1.2] At least one condensate booster pump running. [4.1.3] Condensate System aligned to supply suction to RFPs. Standard: | [4.1.1] At least one condensate pump running. | ||
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | SAT | ||
[4.1.2] At least one condensate booster pump running. | |||
[4.2] VERIFY Main Oil Pump running for each RFPT to be started. Standard: | [4.1.3] Condensate System aligned to supply suction to RFPs. | ||
Verifies main oil pump running for RFPT | UNSAT Standard: | ||
[4.3] VERIFY CLOSED 3-FCV-3-19, RFP | N/A Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | ||
Standard: | Step 5: | ||
VERIFY CLOSED 3-FCV-3-19, RFP | [4.2] VERIFY Main Oil Pump running for each RFPT to be started. | ||
SAT Standard: | |||
UNSAT Verifies main oil pump running for RFPT 3A N/A Step 6: Critical Step | |||
[4.3] VERIFY CLOSED 3-FCV-3-19, RFP 3A DISCHARGE VALVE. | |||
SAT Standard: | |||
UNSAT VERIFY CLOSED 3-FCV-3-19, RFP 3A DISCHARGE VALVE. | |||
N/A 8 | |||
Job Performance Measure (JPM) | |||
Standard: | STEP / STANDARD SAT / UNSAT Step 7: | ||
Depresses 3-HS-46-8A | [4.4] DEPRESS 3-HS-46-8A, RFPT 3A SPEED CONT RAISE/LOWER, Critical Step and VERIFY amber light is illuminated. | ||
[4.5] DEPRESS 3-HS-3-124A , RFPT | SAT Standard: | ||
Standard: | UNSAT Depresses 3-HS-46-8A N/A Step 8: | ||
Depresses 3 | [4.5] DEPRESS 3-HS-3-124A, RFPT 3A TRIP RESET. Critical Step Standard: SAT Depresses 3-HS-3-124A and resets RFPT Trip and verifies the 3-ZI UNSAT 123 LP Stop Valve and 3-ZI-127 HP Stop Valve comes OPEN. | ||
-HS-3-124A and resets RFPT Trip and verifies the 3 | N/A Step 9: | ||
-ZI | [4.6] PLACE 3-HS-46-112A RFPT 3A START/LOCAL ENABLE, in Critical Step START. | ||
-ZI-127 HP Stop Valve comes OPEN. | SAT Standard: | ||
UNSAT Places 3-HS-46-112A in START N/A Note to Examiner: | |||
[4.6] PLACE 3-HS-46-112A RFPT | RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10: | ||
Places 3-HS-46-112A in START | [4.7] CHECK RFPT 3A speed increases to approximately 600 rpm. | ||
RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10: | SAT Standard: | ||
Standard: | UNSAT Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 3-EOI-APPENDIX-11F. N/A CUE: | ||
Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 3-EOI-APPENDIX-11F. | US: Proceed as directed per 3-EOI-APPENDIX-11F. | ||
AO: Reports an oil leak of ~5 gpm on RFPT A bearings. | |||
9 | |||
Standard: | Job Performance Measure (JPM) | ||
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | STEP / STANDARD SAT / UNSAT Step 11: | ||
[1] IF BOTH of the following exist: | |||
* Emergency RPV Depressurization is required, AND | |||
* Group 1 Isolation Signal exists, THEN EXIT this procedure and ENTER EOI Appendix 11H. SAT UNSAT Standard: | |||
N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | |||
Step 12: | |||
[2] VERIFY MSIVs open. | |||
SAT Standard: | |||
UNSAT Verifies MSIVs OPEN N/A 10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 13: | |||
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. | |||
SAT Standard: | |||
-7 in. Hg. Standard: | UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 14: | ||
Verifies Hotwell Pressure at or below | |||
-7 in. Hg | |||
[4] PLACE RFPTs in service as follows: | [4] PLACE RFPTs in service as follows: | ||
[4.1] VERIFY the following: | [4.1] VERIFY the following: | ||
[4.1.1] At least one condensate pump running. [4.1.2] At least one condensate booster pump running. [4.1.3] Condensate System aligned to supply suction to RFPs. Standard: | [4.1.1] At least one condensate pump running. | ||
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | SAT | ||
[4.1.2] At least one condensate booster pump running. | |||
[4.1.3] Condensate System aligned to supply suction to RFPs. | |||
UNSAT Standard: | |||
N/A Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | |||
Step 15: | |||
[4.2] VERIFY Main Oil Pump running for each RFPT to be started. | |||
SAT Standard: | |||
UNSAT Verifies main oil pump running for RFPT 3B N/A Step 16: Critical Step | |||
[4.3] VERIFY CLOSED 3-FCV-3-12, RFP 3B DISCHARGE VALVE. | |||
SAT Standard: | |||
UNSAT VERIFY CLOSED 3-FCV-3-12, RFP 3B DISCHARGE VALVE. | |||
N/A 11 | |||
SAT | Job Performance Measure (JPM) | ||
[4. | STEP / STANDARD SAT / UNSAT Step 17: | ||
[4.4] DEPRESS 3-HS-46-9A, RFPT 3B SPEED CONT RAISE/LOWER, Critical Step and VERIFY amber light is illuminated. | |||
[4. | SAT Standard: | ||
Standard: | UNSAT Depresses 3-HS-46-9A N/A Step 18: | ||
[4.5] DEPRESS 3-HS-3-150A, RFPT 3B TRIP RESET. Critical Step Standard: SAT Depresses 3-HS-3-150A and verifies the 3-ZI-1-133 LP Stop Valve and 3- UNSAT FCV-135 HP Stop Valve comes OPEN. | |||
N/A Step 19: | |||
[4.6] PLACE 3-HS-46-138A, RFPT 3B START/LOCAL ENABLE, in Critical Step START. | |||
SAT Standard: | |||
UNSAT Places 3-HS-46-138A in START N/A Step 20: | |||
[4.7] CHECK RFPT 3B speed increases to approximately 600 rpm. | |||
SAT Standard: | |||
UNSAT Verifies RFPT 3B speed increases to approximately 600 rpm N/A 12 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 21: | |||
[4.8] VERIFY OPEN 3-FCV-3-13, RFP 3B MIN FLOW VALVE. Critical Step Standard: SAT Verifies 3-FCV-3-13 OPEN UNSAT N/A Step 21: | |||
CAUTION RFP discharge pressure is limited to below 1250 psig to avoid system damage. | |||
[4.9] PLACE 3-HS-46-9A, RFPT 3B SPEED CONT RAISE/LOWER in Critical Step RAISE to raise RFPT speed, maintaining discharge pressure less than 1250 psig. | |||
SAT Standard: | |||
UNSAT Raises RFPT speed using Manual Speed Control Handswitch, N/A maintaining discharge pressure <1250 psig as indicated on 3-PI-3-9A RFPT 3B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable). | |||
STOP TIME END OF TASK 13 | |||
Standard: | |||
Verifies 3-FCV-3-13 OPEN | |||
[4.9] PLACE 3-HS-46-9A, RFPT | |||
Raises RFPT speed using Manual Speed Control Handswitch, maintaining discharge pressure <1250 psig as indicated on 3-PI-3-9A RFPT 3B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable). | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. The Unit 3 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 3C. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to place 3A RFPT in alternate pressure control, as directed by 3-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig. | |||
14 | |||
Job Performance Measure (JPM) | |||
N2 MAKEUP TO PRIMARY CONTAINMENT WITH SITE: BFN JPM TITLE: | |||
2-EOI-APPENDIX-14A JPM NUMBER: 669 U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-77 Lineup nitrogen Makeup to primary TASK NUMBER / TASK TITLE(S): | |||
Containment IAW EOI-APPENDIX-14A K/A RATINGS: RO: 3.7SRO: 3.8 223001 Primary Containment System and Auxiliaries A2.04; Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT SYSTEM AND AUXILIARIES ; and K/A No. &STATEMENT: (b) based on those predictions, use procedures to correct, control, or mitigate the consequences ofthose abnormal conditions or operations: High containment/drywell hydrogen concentration RELATED PRA INFORMATION: None SAFETY FUNCTION: 5 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _669 U2__ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration. | |||
Job Performance Measure (JPM) | |||
JPM Number: | |||
_669 U2__ | |||
TASK STANDARD: | |||
Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 2-EOI-APPENDIX-14A VERIFICATION TIME: 15 min PERFORMANCE TIME: | ||
Procedure: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 285 | |||
: 1. Open Schedule File | : 1. Open Schedule File | ||
: 2. Open Event File | : 2. Open Event File | ||
: 3. Reset to IC | : 3. Reset to IC-28 and take out of freeze. | ||
-28 and take out of freeze. | |||
: 4. Man Scram Rx and place MS to SD. | : 4. Man Scram Rx and place MS to SD. | ||
: 5. Inhibit ADS & Open 6 ADS Valves. | : 5. Inhibit ADS & Open 6 ADS Valves. | ||
: 6. Fire Trigger 2 | Console | ||
: 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch in BYPASS per EOI APPDX 19 | : 6. Fire Trigger 2 Operator | ||
: 8. Place DW Vent in Service per EOI APPX 12 9. Wait for Group 6 schedule file to time out and alrms to settle | : 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch Instructions in BYPASS per EOI APPDX 19 | ||
: 8. Place DW Vent in Service per EOI APPX 12 | |||
: 9. Wait for Group 6 schedule file to time out and alrms to settle | |||
: 10. Freeze simulator and save IC. | : 10. Freeze simulator and save IC. | ||
Malfunctions Description Event Severity Delay Initial set | Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 2 100 0 Yes INSIDE DRYWELL TH23 FUEL CLADDING 2 100% 0 N/A DAMAGE RC08 RCIC STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE HP04 HPCI STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE CS04A CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV II RD01A CRD PUMP TRIP 1 N/A 0 N/A 2A RD01B CRD PUMP TRIP 1 N/A 0 N/A 2B FW01A CONDENSATE 1 N/A 0 N/A PUMP TRIP 2A FW01B CONDENSATE 1 N/A 0 N/A 3 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
PUMP TRIP 2B FW01C CONDENSATE 1 N/A 0 N/A PUMP TRIP 2C PC08 H2 IN DRYWELL_ 2 29 0 N/A PC09 OXYGEN IN 2 2.8 0 N/A DRYWELL_ | |||
PC10 H2 IN 2 18 0 N/A SUPPRESSION POOL_ | |||
PC11 OXYGEN IN 2 1.5 0 N/A SUPPRESSION POOL_ | |||
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLOXA554C9 DW EQUIP DRAIN 2 N/A N/A ON SUMP LEVEL ABNORMAL Schedule File(s): | |||
* JPM 669 U2 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.sch | |||
* Appendix\App. 8E.sch | |||
* JPM 669 U2 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.evt 4 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/15 All Initial issue 5 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
The Reactor is shutdown. | * The Reactor is shutdown. | ||
2-EOI-APPENDIX-12has been completed | * 2-EOI-APPENDIX-12has been completed | ||
PCIS Group 6 has been overridden per 2 | * 2-EOI-APPENDIX-19 has been completed. | ||
-EOI-APPENDIX- | * PCIS Group 6 has been overridden per 2-EOI-APPENDIX-8E. | ||
INITIATING CUES: | |||
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2-EOI-APPENDIX-14A beginning on step 2. | |||
6 | |||
Job Performance Measure (JPM) | |||
: | START TIME STEP / STANDARD SAT / UNSAT Step 1: | ||
: 2. MONITOR Drywell and Suppression Chamber H2 and O2concentrations on one or more of the following displays(2-EOI Appendix 19): | |||
- | SAT | ||
. | * 2-MON-76-110, H2/O2 ANALYZER (Panel 2-9-55) | ||
UNSAT | |||
* 2-XR-76-110, H2/O2 CONCENTRATION (Panel 2-9-54) | |||
N/A Standard: | |||
Verifies H2 and O2 concentrations Step 2: | |||
: 3. IF ................. Drywell/Suppression Chamber H2 /O2 analyzer is or becomes inoperable, SAT THEN ...........NOTIFY Chemistry Lab to sample Drywell andSuppression Chamber for H2 and O2 using CI-644. | |||
UNSAT Standard: | |||
N/A Verifies Drywell/Suppression Chamber H2 /O2 analyzers are Operable 7 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 3: | |||
4.WHEN ......... Drywell or Suppression Chamber H2 or O2 concentration is increasing,THEN ........... CONTINUE in this procedure. SAT Standard: UNSAT Observes a rise in Drywell H2 Concentration and continues with N/A procedure. | |||
Step 4: | |||
NOTE This procedure assumes that the normal makeup is from N2 Storage Tank B. | |||
SAT | |||
: 5. DISPATCH personnel to N2 Storage Tank B to CHECK 0-PI-76-331, UNSAT N2 TANK B PRESSURE INDICATOR between 160 and 190 psig. | |||
N/A Standard: | |||
Dispatches UO to verifyN2 Storage Tank B Pressure CUE: N2 Storage Tank B Pressure is reading 180 psig Step 5: | |||
: 6. DETERMINE area with highest H2 and/or O2 concentrations and Critical Step INFORM SRO. | |||
SAT Standard: | |||
UNSAT Correctly determines highest concentration is in the drywell and informs US N/A CUE: If asked about 15 minute sample time, state 15 minutes have elapsed 8 | |||
SAT | Job Performance Measure (JPM) | ||
: | STEP / STANDARD SAT / UNSAT Step 6: | ||
Critical Step | |||
: 7. VERIFY PCIS RESET (Panel 2-9-4). | |||
SAT Standard: | |||
UNSAT Verifies PCIS RESET on Panel 2-9-4 N/A Step 7: | |||
Standard: | Critical Step | ||
: | : 8. IF ................. It is desired to makeup N2 to the Suppression Chamber,THEN ...........CONTINUE in this procedure at Step 10. SAT Standard: UNSAT Correctly determine step is not applicable and proceeds to step 9. N/A Step 8: | ||
: 9. CONTROL Drywell H2 and O2 as follows: | |||
Critical Step | |||
: a. OPEN the following valves to admit N2 to Drywell (Panel 2-9-3): | |||
SAT | |||
* 2-FCV-76-18, DRYWELL N2 MAKEUP INBDISOLATION VLV | |||
* 2-FCV-76-17, PRI CTMT N2 MAKEUP OUTBDISOLATION VLV. UNSAT Standard: | |||
N/A OPENS 2-FCV-76-18, DRYWELL N2 MAKEUP INBD ISOLATION VLV & | |||
2-FCV-76-17, PRI CTMT N2 MAKEUP OUTBD ISOLATION VLV Step 9: | |||
: b. SLOWLY ADJUST 2-PC-76-14, DW/SUPPR CHBR N2 MU Critical Step PRESS CONTROL (Panel 2-9-3), to maintain flow > 55 and | |||
<60 scfm on 2-XR-76-14, DW/SUPPR CHBR N2 MAKEUP SAT FLOW/PRESS (Panel 2-9-3), or as directed by SRO if SAMG execution is in progress. | |||
UNSAT Standard: | |||
N/A Achieves a flowrate between 55-60 scfm and monitors Drywell Hydrogen Concentration Lowering 9 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 10: | |||
Job Performance Measure (JPM) | : c. CONTINUEN2 admission to the Drywell UNTIL Drywell H2 andO2 are SAT below desired values. | ||
UNSAT Standard: | |||
N/A Monitors Drywell Hydrogen Concentration Note to Examiner: Once satisfied with N2 Flow established between 55 - 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task. | |||
Standard: | |||
Monitors Drywell Hydrogen Concentration | |||
- 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task. | |||
Pass/ Fail Criteria: Establish N2 Flow> 55 scfm and H2 Concentration on a downward trend. | Pass/ Fail Criteria: Establish N2 Flow> 55 scfm and H2 Concentration on a downward trend. | ||
STOP TIME END OF TASK | STOP TIME END OF TASK 10 | ||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
The Reactor is shutdown. | * The Reactor is shutdown. | ||
2-EOI-APPENDIX-12 has been completed | * 2-EOI-APPENDIX-12 has been completed | ||
PCIS Group 6 has been overridden per 2 | * 2-EOI-APPENDIX-19 has been completed. | ||
-EOI-APPENDIX-8E. | * PCIS Group 6 has been overridden per 2-EOI-APPENDIX-8E. | ||
INITIATING CUES: | |||
INITIATING CUES | The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2-EOI-APPENDIX-14A beginning on step 2. | ||
: | 11 | ||
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2 | |||
-EOI-APPENDIX-14A beginning on step 2 | |||
TASK | Job Performance Measure (JPM) | ||
N2 MAKEUP TO PRIMARY CONTAINMENT WITH 3-SITE: BFN JPM TITLE: | |||
EOI-APPENDIX-14A JPM NUMBER: 670 U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-77 Lineup nitrogen Makeup to primary TASK NUMBER / TASK TITLE(S): | |||
Containment IAW EOI-APPENDIX-14A K/A RATINGS: RO: 3.7SRO: 3.8 223001 Primary Containment System and Auxiliaries A2.04; Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT SYSTEM AND AUXILIARIES ; and K/A No. &STATEMENT: (b) based on those predictions, use procedures to correct, control, or mitigate the consequences ofthose abnormal conditions or operations: High containment/drywell hydrogen concentration RELATED PRA INFORMATION: None SAFETY FUNCTION: 5 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _670 U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 3-EOI-APPENDIX-14A VERIFICATION TIME: | ||
Procedure: | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
Additional comment sheets attached? | RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | ||
SIGNATURE: ___________________________ DATE: __________ | |||
RESULTS: SATISFACTORY ____ | EXAMINER 2 | ||
UNSATISFACTORY ____ | |||
(Retain entire JPM for records) | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 285 | |||
: 1. Open Schedule File | : 1. Open Schedule File | ||
: 2. Open Event File | : 2. Open Event File | ||
: 3. Reset to IC | : 3. Reset to IC-28 and take out of freeze. | ||
-28 and take out of freeze. | |||
: 4. Man Scram Rx and place MS to SD. | : 4. Man Scram Rx and place MS to SD. | ||
: 5. Inhibit ADS & Open 6 ADS Valves. | : 5. Inhibit ADS & Open 6 ADS Valves. | ||
: 6. Fire Trigger 2 | Console | ||
: 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch in BYPASS per EOI APPDX 19 | : 6. Fire Trigger 2 Operator | ||
: 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch Instructions in BYPASS per EOI APPDX 19 | |||
: 8. Place DW Vent in Service per EOI APPX 12 | : 8. Place DW Vent in Service per EOI APPX 12 | ||
: 9. Wait for Group 6 schedule file to time out and alrms to settle | : 9. Wait for Group 6 schedule file to time out and alrms to settle | ||
: 10. Freeze simulator and save IC. | : 10. Freeze simulator and save IC. | ||
Malfunctions Description Event Severity Delay Initial set | Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 2 100 0 Yes INSIDE DRYWELL TH23 FUEL CLADDING 2 100% 0 N/A DAMAGE RC08 RCIC STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE HP04 HPCI STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE CS04A CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV II RD01A CRD PUMP TRIP 1 N/A 0 N/A 2A RD01B CRD PUMP TRIP 1 N/A 0 N/A 2B 3 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
FW01C CONDENSATE 1 N/A 0 N/A PUMP TRIP 2C PC08 H2 IN DRYWELL_ 2 29 0 N/A PC09 OXYGEN IN 2 2.8 0 N/A DRYWELL_ | |||
PC10 H2 IN 2 18 0 N/A SUPPRESSION POOL_ | |||
PC11 OXYGEN IN 2 1.5 0 N/A SUPPRESSION POOL_ | |||
Overrides Description Event Severity Delay Initial set ZLOXA554C9 DW EQUIP DRAIN 2 N/A N/A ON SUMP LEVEL ABNORMAL Schedule File(s): | |||
* JPM 669 U3 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.sch | |||
* Appendix\App. 8E.sch | |||
* JPM 669 U3 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.evt 4 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/15 All Initial issue 5 | |||
You are an Operator on Unit | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
3-EOI-APPENDIX-12 has been completed. | INITIAL CONDITIONS: | ||
3-EOI-APPENDIX-19 has been completed. | You are an Operator on Unit 3. | ||
PCIS Group 6 has been overridden per 3 | * The Reactor is shutdown. | ||
-EOI-APPENDIX- | * 3-EOI-APPENDIX-12 has been completed. | ||
* 3-EOI-APPENDIX-19 has been completed. | |||
* PCIS Group 6 has been overridden per 3-EOI-APPENDIX-8E. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 3-EOI-APPENDIX-14A beginning on step 2. | |||
6 | |||
Job Performance Measure (JPM) | |||
: | START TIME STEP / STANDARD SAT / UNSAT Step 1: | ||
: 3. MONITOR Drywell and Suppression Chamber H2 and O2concentrations on one or more of the following displays(3-EOI Appendix 19): | |||
. | SAT | ||
* 3-MON-76-110, H2/O2 ANALYZER (Panel 3-9-55) | |||
UNSAT | |||
* 3-XR-76-110, H2/O2 CONCENTRATION (Panel 3-9-54) | |||
N/A Standard: | |||
Verifies H2 and O2 concentrations Step 2: | |||
: 3. IF ................. Drywell/Suppression Chamber H2 /O2 analyzer is or becomes inoperable, SAT THEN ...........NOTIFY Chemistry Lab to sample Drywell UNSAT andSuppression Chamber for H2 and O2 using CI-644. | |||
N/A Standard: | |||
Verifies Drywell/Suppression Chamber H2 /O2 analyzers are Operable 7 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 3: | |||
: 4. WHEN ......... Drywell or Suppression Chamber H2 or O2 concentration is increasing,THEN ........... CONTINUE in this procedure. SAT Standard: UNSAT Observes a rise in Drywell H2 Concentration and continues with N/A procedure. | |||
Step 4: | |||
NOTE This procedure assumes that the normal makeup is from N2 Storage Tank B. | |||
SAT | |||
: 5. DISPATCH personnel to N2 Storage Tank B to CHECK 0-PI-76-331, UNSAT N2 TANK B PRESSURE INDICATOR between 160 and 190 psig. | |||
N/A Standard: | |||
Dispatches UO to verifyN2 Storage Tank B Pressure CUE: N2 Storage Tank B Pressure is reading 180 psig Step 5: | |||
: 6. DETERMINE area with highest H2 and/or O2 concentrations and Critical Step INFORM SRO. | |||
SAT Standard: | |||
UNSAT Correctly determines highest concentration is in the drywell and informs US N/A CUE: If asked about 15 minute sample time, state 15 minutes have elapsed 8 | |||
SAT | Job Performance Measure (JPM) | ||
: | STEP / STANDARD SAT / UNSAT Step 6: | ||
Critical Step | |||
: 7. VERIFY PCIS RESET (Panel 3-9-4). | |||
SAT Standard: | |||
UNSAT Verifies PCIS RESET on Panel 3-9-4 N/A Step 7: | |||
Critical Step | |||
: 8. IF ................. It is desired to makeup N2 to the Suppression Chamber,THEN ...........CONTINUE in this procedure at Step 10. SAT Standard: UNSAT Correctly determine step is not applicable and proceeds to step 9. N/A Step 8: | |||
: 9. CONTROL Drywell H2 and O2 as follows: | |||
Critical Step | |||
: a. OPEN the following valves to admit N2 to Drywell (Panel 3-9-3): | |||
SAT | |||
* 3-FCV-76-18, DRYWELL N2 MAKEUP INBDISOLATION VLV | |||
* 3-FCV-76-17, PRI CTMT N2 MAKEUP OUTBDISOLATION VLV. UNSAT Standard: | |||
N/A OPENS 3-FCV-76-18, DRYWELL N2 MAKEUP INBD ISOLATION VLV | |||
&3-FCV-76-17, PRI CTMT N2 MAKEUP OUTBD ISOLATION VLV Step 9: | |||
: b. SLOWLY ADJUST 3-PC-76-14, DW/SUPPR CHBR N2 MUPRESS Critical Step CONTROL (Panel 3-9-3), to maintain flow between 55 and60 scfm on 3-XR-76-14, DW/SUPPR CHBR N2 MAKEUPFLOW/PRESS (Panel 3-SAT 9-3), or as directed by SRO if SAMGexecution is in progress. | |||
UNSAT Standard: | |||
N/A Achieves a flowrate between 55-60 scfm and monitors Drywell Hydrogen Concentration Lowering 9 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 10: | |||
: c. CONTINUE N2 admission to the Drywell UNTIL Drywell H2 and O2 are below desired values. SAT Standard: UNSAT Monitors Drywell Hydrogen Concentration N/A Note to Examiner: Once satisfied with N2 Flow established between 55 - 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task. | |||
: | |||
Standard: | |||
Monitors Drywell Hydrogen Concentration | |||
- 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task. | |||
Pass/ Fail Criteria: Establish N2 Flow > 55 scfm and H2 Concentration on a downward trend. | Pass/ Fail Criteria: Establish N2 Flow > 55 scfm and H2 Concentration on a downward trend. | ||
STOP TIME END OF TASK | STOP TIME END OF TASK 10 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is shutdown. | |||
* 3-EOI-APPENDIX-12 has been completed. | |||
* 3-EOI-APPENDIX-19 has been completed. | |||
* PCIS Group 6 has been overridden per 3-EOI-APPENDIX-8E. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 3-EOI-APPENDIX-14A beginning on step 2. | |||
11 | |||
Job Performance Measure (JPM) | |||
Restore Offsite Power to 4KV shutdown board at SITE: BFN JPM TITLE: | |||
PNL 9-23 JPM NUMBER: 631 U2 REVISION: 0 TASK SRO STA UO NAUO APPLICABILITY: | |||
U-082-NO-09 / Restore Offsite Power to 4KV TASK NUMBER / TASK TITLE(S): | |||
shutdown board at PNL 9-23 K/A RATINGS: RO 3.4 SRO 3.4 262001 A.C. Electrical Distribution A4.02 Ability to manually operate and/or monitor in the control room: Synchroscope, K/A STATEMENT: | |||
including understanding of running andincoming voltages RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 6 EVALUATION LOCATION: In -P la n t Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NATIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
: | OPERATOR: ________________________________ JPM Number: 631 U2 RO SRO DATE: _______ | ||
TASK STANDARD: Perform operations necessary to restore offsite power to 4KV SD BD A from 4KV SD BUS 1. | |||
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure 0-OI-82 VERIFICATION TIME: 15 Min PERFORMANCE TIME: | |||
COMMENTS: | |||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 286 Console 1. Reset to IC 28 and take out of freeze Operator 2. Start A EDG and parallel with offsite Instructions 3. Open 4-kV Shutdown Board A Breaker 1614 Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set 3 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. | |||
I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
No Inclement weather currently exists in the area 8 | * No Inclement weather currently exists in the area | ||
-OI-82, Standby Diesel Generator System. | * 8 hours ago, 4 KV Shutdown Board A was separated from Offsite Power in accordance with 0-OI-82, Standby Diesel Generator System. | ||
INITIATING CUE: | |||
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board A using the normal feeder breaker and remove DG A from parallel operation in accordance with 0-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23. | |||
4 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / | |||
UNSAT Step 1: | |||
0-OI-82 Standby Diesel Generator System Section 8.3 Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23 NOTE The following list of 4-kV shutdown board normal and alternate feeder breakers may be useful when performing this section: | |||
SAT | |||
__UNSAT Shutdown A B C D Board N/A Norm Feed Bkr 1614 1616 1718 1724 Alt Feed Bkr 1716 1714 1624 1618 | |||
[1] VERIFY 4-kV Shutdown Board A is being supplied power by its respective Diesel Generator as the only source of power. | |||
Standard: | |||
Verifies 4-kV Shutdown Board A is being supplied by DG A. | |||
Step 2: | |||
[2] VERIFY the associated 4kV shutdown board auto transfer lockout relay is tripped to MANUAL. | |||
Diesel Handswitch Name Handswitch Panel SAT No. | |||
4KV SD BD A UNSAT A 0-211-3EA 0-9-23-7 AUTO/LOCKOUT RESET N/A Standard: | |||
Verifies 4KV SD BD A AUTO/LOCKOUT RESET, HS-0-211-A, is tripped to manual. | |||
5 | |||
Job Performance Measure (JPM) | |||
- | STEP / STANDARD SAT / | ||
-kV Shutdown | UNSAT Step 3: | ||
- | [3] PLACE the synchroscope switch for the 4-kV shutdown board Critical Step feeder breaker that is to be paralleled with the Diesel Generator in ON. SAT Standard: UNSAT Places Synchroscope switch for 4-kV Shutdown Board A normal N/A feeder breaker 1614 to ON. | ||
Step 4: | |||
[4] VERIFY 4-kV Shutdown Bus 1(2) voltage is between 3950 Volts SAT and 4400 Volts and NOT undergoing abnormal voltage transients. | |||
UNSAT Standard: | |||
N/A Verifies 4-kV Shutdown Bus 1 voltage is between 3950 Volts and 4400 Volts and NOT undergoing abnormal voltage transients. | |||
Step 5: | |||
[5] VERIFY associated incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients. | |||
Shutdown Instrument Name Instrument No. Panel Bd SAT A or B GEN SYNC 0-SI-82-0AB 0-9-23-7 FREQUENCY UNSAT C or D GEN SYNC 0-SI-82-0CD 0-9-23-8 FREQUENCY N/A Standard: | |||
Verifies incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients using GEN SYNC FREQUENCY,0-SI-82-AB. | |||
6 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 6: | |||
CAUTION DO NOT parallel the Diesel Generators with an unstable offsite source or during inclementweather (e.g., lightning, heavy winds). | |||
SAT | |||
[6] IF 4-kV Shutdown Bus 1 (2) is experiencing abnormal voltage or UNSAT frequency conditions, THEN PERFORM the following: | |||
N/A Standard: | |||
STEP N/A Step 7: | |||
CAUTION Only one Unit 1 and 2 Diesel Generator at a time is allowed to be operated in parallel with system. | |||
[6] | |||
Standard: | |||
Critical Step | Critical Step | ||
[7] PULL and PLACE the associated Diesel Generator mode selector switch in PARALLELED WITH SYSTEM. SAT Diesel Handswitch Name Handswitch Panel UNSAT No. | |||
A DG A MODE SELECT 0-HS-82-A/5A 0-9-23-7 N/A Standard: | |||
Pulls DG A MODE SELECT switch 0-HS-82-A/5A and places it in PARALLELED WITH SYSTEM. | |||
7 | |||
Job Performance Measure (JPM) | |||
Diesel | STEP / STANDARD SAT / | ||
UNSAT Step 8: | |||
CAUTION Failure of the PARALLELED WITH SYSTEM light to illuminate in the following step could indicate that the DG is still in SINGLE UNIT operation and result in overload when the DG output breaker is closed. | |||
SAT UNSAT | |||
[8] RELEASE the Diesel Generator mode selector switch and OBSERVE PARALLELED WITH SYSTEM light illuminated. | |||
N/A Standard: | |||
Releases the Diesel Generator A mode selector switch, 0-HS A/5A and observesPARALLELED WITH SYSTEM light is illuminated. | |||
Step 9: | |||
[9] ADJUST Diesel Generator frequency using the associated Diesel Generator governor control switch to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction. | |||
Critical Step Diesel Handswitch Name Handswitch Panel No. SAT A DG A GOVERNOR 0-HS-82-A/3A 0-9-23-7 CONTROL UNSAT Standard: N/A AdjustsDiesel Generator A frequency using Diesel Generator governor control switch, 3-HS-82-A/3A, (in lower direction) to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction. | |||
8 | |||
SAT UNSAT N/A Step | Job Performance Measure (JPM) | ||
[ | STEP / STANDARD SAT / | ||
-kV shutdown board feeder breaker that | UNSAT Step 10: | ||
[10] USE the associated Diesel Generator voltage regulator control switch to match Diesel Generator and System voltages. | |||
Diesel Instrument Name Inst No. Panel DG A VOLT REGULATOR 0-HS-82-A/2A SAT CONT A GEN SYNC REF VOLTAGE 0-EI-82-AB 0-9-23-7 UNSAT SYSTEM SYNC REF 0-EI-211-0AB VOLTAGE N/A Standard: | |||
[ | Matches DG A voltage with system voltage using DG A VOLT REGULATOR CONT switch 0-HS-82-A/2A. | ||
Step 11: | |||
[11] WHEN the synchroscope needle is approximately 2 minutes on Critical Step the right hand side of the 12 o'clock position, THEN CLOSE the 4-kV shutdown board feeder breaker that is to be SAT paralleled with the Diesel Generator. | |||
UNSAT Standard: | |||
N/A Closesthe 4-kV shutdown board feeder breaker 1614 when the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position. | |||
Step 12: | |||
[12] PLACE the synchroscope switch for the 4-kV shutdown board SAT feeder breaker that was paralleled with the Diesel Generator in OFF. | |||
UNSAT Standard: | |||
N/A Places the synchroscope switch for BKR 1614 in OFF. | |||
9 | |||
toINCREASE kW and kVAR load, in increments of 100kWevery 15 minutes. | Job Performance Measure (JPM) | ||
Diesel Handswitch Name | STEP / STANDARD SAT / | ||
[13.3] STEP N/A [13.4] WHEN smoke becomes relatively clear, | UNSAT Step 13: | ||
NOTE If diesel operates greater than 4 hours at less than 50% load, the diesel should be loaded to full load for at least 30 minutes prior to engine shutdown. This will allow the engine to clean out any oil accumulations from the exhaust manifolds. | |||
[13] IF DG has been operating at a low-load condition (50%) for an extended period of time (4 hours) THEN PERFORM the following (Otherwise N/A): | |||
[13.1] USE the associated Diesel Generator's governor controlswitch and voltage regulator control switch toINCREASE kW and kVAR load, in increments of Critical Step 100kWevery 15 minutes. | |||
SAT Diesel Handswitch Name Hands Panel witch UNSAT No. | |||
DG A GOVERNOR CONTROL 0-HS-N/A 82-A/3A A 0-9-23-7 DG A VOLT REGULATOR 0-HS-CONTROL 82-A/2A | |||
[13.2] OBSERVE the exhaust stack smoke concentration from outside the DG room after each incremental increase. | |||
[13.3] STEP N/A | |||
[13.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible. | |||
[13.5] MAINTAIN 100% load for a minimum of 30 minutes. | [13.5] MAINTAIN 100% load for a minimum of 30 minutes. | ||
Standard: | Standard: | ||
Loads DG to 2600 kW and 1850 kVAR by using 0-HS-82-A/3A and 0-HS-82-A/2A handswitches. | |||
CUE: After first 100 kW load adjustment state 15 minutes have elapsed and no observable black smoke from exhaust stack for time compression and continue to full load. | |||
10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
Panel | UNSAT Step 14: | ||
Step | NOTE Lagging VARs should be maintained when adjusting kW load (rising or lowering). This may require kW load adjustment to be stopped periodically to allow for adjusting kVAR load. Once desired kW load is achieved, Illustration 1 should be referred to for determination of kVAR loading required to obtain a power factor (pf) of 0.8 lagging. Diesel generator kVAR load should then be adjusted to obtain a 0.8 pf lagging. IF system conditions will NOT permit the kVAR loading required to obtain a 0.8 pf lagging, kVAR load should be adjusted to the maximum kVAR lagging the system will allow. | ||
[15] | SAT UNSAT | ||
[14] USE the associated Diesel Generator's governor control switch and voltage regulator control switch to obtain desired kW and N/A kVAR load. | |||
Diesel Handswitch Name Handswitch No. Panel DG A GOVERNOR CONTROL 0-HS-82-A/3A A 0-9-23-7 DG A VOLT REGULATOR CONT 0-HS-82-A/2A Standard: | |||
Obtains desired kW and kVAR load using DG A Governor Control switch, 0-HS-82-A/3A and DG Volt Regulator Cont switch, 0-HS-82-A/2A. | |||
CUE: state 30 minutes have elapsed continue with procedure. | |||
Step 15: | |||
[15] MONITOR the offsite source that is paralleled with the Diesel Generator. SAT | |||
[16] IF abnormal voltage or frequency transients are experienced, UNSAT THEN N/A Standard: | |||
Step is N/A 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
UNSAT Step 16: | |||
[17] WHEN Parallel with System operation is no longer desired, THEN UNLOAD the Diesel Generator as follows: | |||
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVARlimit may result in a reverse power trip of the Diesel Generator output breaker. | CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVARlimit may result in a reverse power trip of the Diesel Generator output breaker. | ||
[17.1] | [17.1] USE the associated Diesel Generator's governor control Critical Step switch and voltage regulator control switch to reduce generator load to approximately 300 kW and SAT 250 kVAR: | ||
UNSAT Diesel Instrument Name Inst No. Panel N/A DG A GOVERNOR CONTROL 0-HS-82-A/3A DG A VOLTAGE 0-HS-82-A/2A A REGULATOR CONTROL 0-9-23-7 DG A KILOWATTS 0-JI-82-A/A DG A KILOVARS 0-VAR-82-A/A Standard: | |||
Unloads the DG to approximately 300 KW and 250 kVAR. | |||
Step 17 | |||
Panel A DG A BKR 1818 0-HS-211-A/ | [17.2] PLACE the associated Diesel Generator breaker control Critical Step switch in TRIP SAT Diesel Handswitch Name Handswitch No. Panel A DG A BKR 1818 0-HS-211-A/22A 0-9-23-7 UNSAT N/A Standard: | ||
Trips Diesel Generator breaker 1818. | |||
12 | |||
. | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 18: | |||
[17.3] PULL and PLACE the associated Diesel Generator mode Critical Step selector switch in SINGLE UNIT. | |||
SAT Diesel Handswitch Name Handswitch No. Panel A DG A MODE SELECT 0-HS-211-A/5A 0-9-23-7 UNSAT N/A Standard: | |||
Pulls and places 0-HS-211-A/5A to Single Unit. | |||
Step 19: | |||
[17.4] RELEASE the Diesel Generator mode selector switch and SAT OBSERVE the SINGLE UNIT light illuminated. | |||
UNSAT Standard: | |||
N/A Verifies Single Unit light illuminated. | |||
CUE: ANOTHER OPERATOR WILL CONTINUE FROM HERE STOP TIME END OF TASK 13 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
No Inclement weather currently exists in the area 8 | * No Inclement weather currently exists in the area | ||
-OI-82, Standby Diesel Generator System. | * 8 hours ago, 4 KV Shutdown Board A was separated from Offsite Power in accordance with 0-OI-82, Standby Diesel Generator System. | ||
INITIATING CUE: | |||
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board A using the normal feeder breaker and remove DG A from parallel operation in accordance with 0-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23. | |||
14 | |||
Job Performance Measure (JPM) | |||
Restore Offsite Power to 4KV shutdown board at PNL 9-SITE: BFN JPM TITLE: | |||
23 U-3 JPM NUMBER: 631 REVISION: 0 TASK SRO STA UO NAUO APPLICABILITY: | |||
U-082-NO-09 / Restore Offsite Power to 4KV TASK NUMBER / TASK TITLE(S): | |||
shutdown board at PNL 9-23 K/A RATINGS: RO 3.4 SRO 3.4 262001 A.C. Electrical Distribution A4.02 Ability to manually operate and/or monitor in the control K/A STATEMENT: room: Synchroscope, including understanding of running and incoming voltages RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 6 EVALUATION LOCATION: In -P la n t Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
-OI-82 | OPERATOR: ________________________________ JPM Number: 631 RO SRO DATE: _______ | ||
TASK STANDARD: Perform operations necessary to restore offsite power to 4KV SD BD EC. | |||
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure 3-OI-82 VERIFICATION TIME: 15 Min PERFORMANCE TIME: | |||
COMMENTS: | |||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
SIMULATOR SETUP IC 28 Exam IC 286 | |||
: 1. Reset to IC 28 and take out of freeze Console | |||
: 2. Start C EDG and parallel with offsite Operator | |||
: 3. Open 4-kV Shutdown Board 3EC Breaker 1338 Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Batch / Pref File(s): | |||
3 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. | |||
I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* No Inclement weather currently exists in the area | |||
* 8 hours ago, 4 KV Shutdown Board 3EC was separated from Offsite Power in accordance with 3-OI-82, Standby Diesel Generator System. | |||
INITIATING CUE: | |||
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board 3EC using the normal feeder breaker and remove DG 3C from parallel operation in accordance with 3-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23. | |||
4 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / | |||
UNSAT Step 1: | |||
3-OI-82 Standby Diesel Generator System Section 8.3 Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23 NOTE The following list of 4-kV shutdown board normal and alternate feeder breakers may be useful when performing this section: | |||
SAT UNSAT Shutdown 3EA 3EB 3EC 3ED Board N/A Norm Feed Bkr 1334 1336 1338 1342 Alt Feed Bkr 1726 1728 1626 1628 | |||
[1] VERIFY 4-kV Shutdown Board 3EC is being supplied power by its respective Diesel Generator as the only source of power. | |||
Standard: | |||
Verifies 4-kV Shutdown Board EC is being supplied by DG C Step 2: | |||
[2] VERIFY the associated 4kV shutdown board auto transfer lockout relay is tripped to MANUAL. | |||
SAT Diesel Handswitch Name Handswitch No. Panel 4KV SD BD 3EC 3-43-211- UNSAT 3C 3-9-23 AUTO/LOCKOUT RESET 3EC N/A Standard: | |||
Verifies 4KV SD BD 3EC AUTO/LOCKOUT RESET, 3-43-211-3EC, is tripped to manual. | |||
5 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
UNSAT Step 3: | |||
[3] PLACE the synchroscope switch for the 4-kV shutdown board Critical Step feeder breaker that is to be paralleled with the Diesel Generator in ON. SAT Standard: UNSAT Places Synchroscope switch for 4-kV Shutdown Board EC normal N/A feeder breaker 1338 to ON Step 4: | |||
[4] CHECK the applicable 4-kV unit board (4-kV bus tie board) | |||
SAT voltage is between 3950 VOLTS and 4400 VOLTS and NOT undergoing abnormal voltage transients. | |||
UNSAT Standard: | |||
N/A Verifies 4-kV Unit Board voltage is between 3950 Volts and 4400 Volts and NOT undergoing abnormal voltage transients. | |||
Step 5: | |||
[5] VERIFY associated incoming frequency is between 59 HERTZ and 61 HERTZ and NOT undergoing abnormal frequency transients. | |||
Shutdown Instrument Name Instrument No. Panel SAT Bd 3EA or GEN SYNC 3-SI-82-3AB 3-9-23 UNSAT 3EB FREQUENCY 3EC or GEN SYNC 3-SI-82-3CD 3-9-23 N/A 3ED FREQUENCY Standard: | |||
Verifies incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients using GEN SYNC FREQUENCY, 3-SI-82-CD . | |||
6 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
UNSAT Step 6: | |||
CAUTION DO NOT parallel the Diesel Generators with an unstable offsite source or during inclement weather (e.g., lightning, heavy winds). SAT UNSAT | |||
[6] IF 4-kV unit board (4-kV bus tie board) is experiencing abnormal voltage or frequency conditions, THEN PERFORM the following: N/A Standard: | |||
N/A Step 7: | |||
CAUTION Only one Unit 1 and 2 Diesel Generator at a time is allowed to be operated in parallel with system. | |||
Critical Step | |||
[7] PULL and PLACE the associated Diesel Generator mode SAT selector switch in PARALLELED WITH SYSTEM. | |||
UNSAT Diesel Handswitch Name Handswitch Panel No. | |||
N/A 3C DG 3C MODE SELECT 3-HS-82-3C/5A 3-9-23 Standard: | |||
Pulls DG 3C MODE SELECT switch 3-HS-82-3C/5A and places it in PARALLELED WITH SYSTEM 7 | |||
Job Performance Measure (JPM) | |||
: | STEP / STANDARD SAT / | ||
: | UNSAT Step 8: | ||
: 3 | CAUTION Failure of the PARALLELED WITH SYSTEM light to illuminate in the following step could indicate that the DG is still in SINGLE UNIT operation and result in overload when the DG output breaker is closed. SAT UNSAT | ||
[8] RELEASE the Diesel Generator mode selector switch and OBSERVE PARALLELED WITH SYSTEM light illuminated. N/A Standard: | |||
Releases the Diesel Generator 3C mode selector switch, 3-HS-82-3C/5C and observes PARALLELED WITH SYSTEM light is illuminated. | |||
Step 9: | |||
[9] ADJUST Diesel Generator frequency using the associated Diesel Generator governor control switch to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction. | |||
Critical Step Diesel Handswitch Name Handswitch Panel No. SAT 3C DG 3C GOVERNOR 3-HS-82-3C/3A 3-9-23 CONTROL UNSAT Standard: N/A Adjusts Diesel Generator 3C frequency using Diesel Generator governor control switch, 3-HS-82-3C/3A (in lower direction) to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction. | |||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 10: | |||
[10] USE the associated Diesel Generator voltage regulator control switch to match Diesel Generator and System voltages. | |||
Dies Instrument Name Inst No. Panel el SAT DG 3C VOLT REGULATOR 3-HS CONT 3C/2A UNSAT 3C GEN SYNC REF VOLTAGE 3-EI-82-3CD 3-9-23 SYSTEM SYNC REF 3-EI-211-VOLTAGE 3ECB/B N/A Standard: | |||
Matches DG C voltage with system voltage using DG 3C VOLT REGULATOR CONT switch 3-HS-82-3C/2A Step 11: | |||
[11] WHEN the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position, THEN Critical Step CLOSE the 4-kV shutdown board feeder breaker that is to be SAT paralleled with the Diesel Generator. | |||
UNSAT Standard: | |||
N/A Closes the 4-kV shutdown board normal feeder breaker 1338 when the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position. | |||
Step 12: | |||
[12] PLACE the synchroscope switch for the 4-kV shutdown board SAT feeder breaker that was paralleled with the Diesel Generator in OFF. UNSAT Standard: N/A Places the synchroscope switch for BKR 1338 in OFF 9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 13: | |||
[13] IF the normal feeder breaker is supplying the 4-kV shutdown board, THEN RESET the associated 4kV shutdown board auto transfer lockout Critical Step relay. | |||
SAT Diesel Handswitch Name Handswitch Panel No. | |||
UNSAT 3C 4KV SD BD 3EC 3-43-211-3EC 3-9-23 AUTO/LOCKOUT N/A RESET Standard: | |||
Resets 4KV SD BD 3EC Auto Transfer Lockout Relay Step 14: | |||
NOTE If diesel operates greater than 4 hours at less than 50% load, the diesel should be loaded to full load for at least 30 minutes prior to engine shutdown. This will allow the engine to clean out any oil accumulations from the exhaust manifolds. | |||
[14] IF DG has been operating at a low-load condition (50%) for an extended period of time (4 hours) THEN PERFORM the following (Otherwise N/A): Critical Step | |||
[14.1] USE the associated Diesel Generators governor control SAT switch and voltage regulator control switch to INCREASE kW and kVAR load, in increments of 100kW every 15 UNSAT minutes. | |||
N/A Diesel Handswitch Name Hands Panel witch No. | |||
DG 3C GOVERNOR CONTROL 3-HS-82-3C/3A 3C 3-9-23 DG 3C VOLT REGULATOR 3-HS-CONTROL 82-3C/2A 10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
UNSAT Step 14 continued: | |||
[14.2] OBSERVE the exhaust stack smoke concentration from outside the DG room after each incremental increase. | |||
[14.3] STEP N/A | |||
[14.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible. | |||
[14.3] STEP N/A [14.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible. | |||
[14.5] MAINTAIN 100% load for a minimum of 30 minutes. | [14.5] MAINTAIN 100% load for a minimum of 30 minutes. | ||
Standard: | Standard: | ||
-HS-82-A/3A and 0-HS-82-A/2A handswitches. | Loads DG to 2600 kW and 1850 kVAR by using 0-HS-82-A/3A and 0-HS-82-A/2A handswitches. | ||
CUE: After first 100 kW load adjustment state | CUE: After first 100 kW load adjustment state 15 minutes have elapsed and no observable black smoke from exhaust stack for time compression and continue to full load. | ||
Step 15: | |||
[15] | NOTE VARs lagging should be maintained when adjusting kW load (rising or lowering). This may require kW load adjustment to be stopped periodically to allow for adjusting kVAR load. Once desired kW load is achieved, Illustration 1 should be referred to for determination of kVAR loading required to obtain a power factor (pf) of 0.8 lagging. Diesel generator kVAR load should then be adjusted to obtain a 0.8 pf lagging. IF system conditions will NOT permit the kVAR loading required to obtain a 0.8 pf lagging, kVAR load should be adjusted to SAT the maximum kVAR lagging the system will allow. | ||
Diesel Handswitch Name Handswitch No. | UNSAT | ||
Panel | [15] USE the associated Diesel Generator's governor control switch N/A and voltage regulator control switch to obtain desired kW and kVAR load. | ||
Diesel Handswitch Name Handswitch No. Panel DG 3C GOVERNOR 3-HS CONTROL 3C/3A 3C 3-9-23 DG 3C VOLT REGULATOR 3-HS CONT 3C/2A 11 | |||
[17] | Job Performance Measure (JPM) | ||
[18] | STEP / STANDARD SAT / | ||
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVAR limit may result in a reverse power trip of the Diesel Generator output breaker. | UNSAT Standard: | ||
[18.1] | Obtains desired kW and kVAR load using DG 3C Governor Control switch, 3-HS-82-3C/3A and DG Volt Regulator Control switch, 3-HS-82-3C/2A CUE: state 30 minutes have elapsed continue with procedure. | ||
Step 16: | |||
[16] MONITOR the offsite source that is paralleled with the Diesel Generator. SAT | |||
[17] IF abnormal voltage or frequency transients are experienced, UNSAT THEN N/A Standard: | |||
Step is N/A Step 17: | |||
[18] WHEN Parallel with System operation is no longer desired, THEN UNLOAD the Diesel Generator as follows: | |||
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVAR limit may result in a reverse power trip of the Diesel Generator output breaker. Critical Step SAT | |||
[18.1] USE the associated Diesel Generator's governor control switch and voltage regulator control switch to reduce UNSAT generator load to approximately 300 kW and 250 kVAR: N/A Diesel Instrument Name Inst No. Panel DG 3C GOVERNOR CONTROL 3-HS-82-3C/3A DG 3C VOLT REGULATOR 3-HS-82-3C/2A 3C 3-9-23 CONT DG 3C KILOWATTS 3-JI-82-3C/A DG 3C KILOVARS 3-VAR-82-3C/A 12 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 17 continued: | |||
. | Standard: | ||
Unloads the DG to approximately 300 KW and 250 kVAR Step 18: | |||
[18.2] PLACE the associated Diesel Generator breaker control Critical Step switch in TRIP. | |||
SAT Diesel Handswitch Name Handswitch No. Panel 3C DG 3C BKR 1832 3-HS-211- 3-9-23 UNSAT 3EC/10A N/A Standard: | |||
Trips breaker DG 3C BKR 1832 Step 19: | |||
[18.3] PULL and PLACE the associated Diesel Generator mode Critical Step selector switch in SINGLE UNIT. | |||
- | SAT Diesel Handswitch Name Handswitch No. Panel 3C DG 3C MODE SELECT 3-HS-82-3C/5A 0-9-23 UNSAT Standard: N/A Pulls and places 3-HS-82-3C/5A to Single Unit Step 20: SAT | ||
- | [18.4] RELEASE the Diesel Generator mode selector switch and UNSAT OBSERVE the SINGLE UNIT light illuminated. | ||
-23 | N/A Standard: | ||
Verifies Single Unit light illuminated CUE: ANOTHER OPERATOR WILL CONTINUE FROM HERE STOP TIME END OF TASK 13 | |||
- | |||
- | |||
- | |||
Job Performance Measure (JPM) | |||
Provide to Applicant INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* No Inclement weather currently exists in the area | |||
* 8 hours ago, 4 KV Shutdown Board 3EC was separated from Offsite Power in accordance with 3-OI-82, Standby Diesel Generator System. | |||
INITIATING CUE: | |||
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board 3EC using the normal feeder breaker and remove DG 3C from parallel operation in accordance with 3-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23. | |||
14 | |||
Job Performance Measure (JPM) | |||
SITE: BFN JPM TITLE: Respond to Off-Gas Post Treatment Radiation HI-HI-HI JPM NUMBER: 190 U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-066-AB-02 -Respond to Off-Gas Post Treatment TASK NUMBER / TASK TITLE(S): | |||
( | Radiation Hi-Hi-Hi K/A RATINGS: RO 2.9 SRO 3.2 271000 Offgas System: A2.16; Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those K/A STATEMENT: predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2) | ||
RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: N/A TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: 190 U2 RO SRO DATE: _______ | |||
TASK STANDARD: Respond to Off-Gas Post Treatment Radiation HI-HI-HI per 2-AOI-66-2 and/or 2-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-66-2, 2-ARP-9-4C/35 VALIDATION TIME: 15 Minutes PERFORMANCE TIME: | |||
: | COMMENTS: | ||
: | Additional comment sheets attached? YES ___ NO ___ | ||
: | RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | ||
- | SIGNATURE: ___________________________ DATE: __________ | ||
EXAMINER 2 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
SIMULATOR SETUP IC 28 Exam IC 287 | |||
: 1. Reset to IC 28 Console 2. Fire Manual Trigger 2 Operator 3. Fire Manual Trigger 1 Instructions 4. Station 2nd operator to respond to alarms Malfunctions Description Event Severity Delay Initial set TH23 FUEL CLADDING 1 50 N/A YES DAMAGE RM14C OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURERM 265A RM14D OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-266A Remotes Description Event Severity Delay Initial set OG06 Bypass FCV-66-28 2 N/A N/A BYP Post Treatment Hi-Hi-Hi Rad Isol Overrides Description Event Severity Delay Initial set ZAORI9014A RX BLDG AREA 1 2.5 N/A YES RAD ZAORI9017A RX BLDG AREA 1 2.6 N/A YES RAD ZAORM90265A 90-265 METER 1 6.0 N/A YES UPSCALE ZAORM90266A 90-266 METER 1 6.0 N/A YES UPSCALE ZAORR90135R1 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90135R2 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZLORM90265A_1 90-265 DRAW LITE 1 N/A N/A YES 3 | |||
Job Performance Measure (JPM) | |||
ZLORM90265A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_4 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_4 90-265 DRAW LITE 1 N/A N/A YES XA553A5 OG PRETREAT 1 N/A N/A YES RAD HI XA553A6 STACK GAS RAD 1 N/A N/A YES HI HI XA553A7 MSL RAD HI 1 N/A N/A YES XA553A13 STACK GAS RAD 1 N/A N/A YES HI XA553A27 MSL RAD HI HI 1 N/A N/A YES XA554C26 CARBON BED 1 N/A N/A YES VAULT RAD HI XA554C27 OG ANNUAL 1 N/A N/A YES RELEASE LIMIT EXCEEDED XA554C33 OG POST TREAT 1 N/A N/A YES RAD HI XA554C34 OG POST TREAT 1 N/A N/A YES RAD HI HI XA554C35 OG POST TREAT 1 N/A N/A YES RAD HI HIHI ZDIHS6628 66-28 VALVE 1 N/A N/A YES CLOSED ZAORR90265R1 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90265R2 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZAORR90160R1 OG PRETREAT 1 -2.0 N/A YES RECORDER UPSCALE XA554B2 RWCU FILTER 1 N/A N/A YES INLET CNDT HIGH Schedule File(s): JPM 190 U2 OG Post treat Rad HI HIHI 4 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are the Unit 2 Operator. Unit 2 is at 100% power. | You are the Unit 2 Operator. Unit 2 is at 100% power. | ||
INITIATING CUE: | |||
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 2-XA-55-4C, window 35. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / UNSAT Performance Step 1: | |||
SAT When directed, identify/obtain copy of ARP-9-4C, window 35. | |||
UNSAT Standard: | |||
N/A Obtains copy of 2-ARP-9-4C, window 35 Examiner Note: Candidate may recognize the annunciator as an entry condition and go directly to 2-AOI-66-2. In that event, continue at Performance Step 5. | |||
Performance Step 2: | |||
2-ARP-9-4C window 35 Operator Action: | |||
A. VERIFY alarm condition on the following | |||
* OFFGAS POST-TREATMENT RADIATION recorder, SAT 2-RR-90-265 on Panel 2-9-2. | |||
* OG POST-TREATMENT CHAN A RAD MON RTMR UNSAT radiationmonitor, 2-RM-90-266A on Panel 2-9-10. | |||
* OG POST-TREATMENT CHAN B RAD MON RTMR N/A radiationmonitor, 2-RM-90-265A on Panel 2-9-10. | |||
Standard: | |||
Verified alarm condition on 2-RR-90-265 and 2-RM-265/266. | |||
Performance Step 3: | |||
B. VERIFY OFF-GAS SYSTEM ISOLATION VALVE, 2-FCV- Critical Step 66-28 has the Mechanical Restraint DISENGAGED and 2-FCV-66-28 isCLOSED. SAT Standard: UNSAT Takes handswitch 2-FCV-66-28 to close and observes green light N/A illuminated and red light out. | |||
Cue: If asked, the Offgas Isolation Valve, 2-FCV-66-28 is NOT mechanically restrained. | |||
6 | |||
Job Performance Measure (JPM) | |||
- | STEP / STANDARD SAT / UNSAT Performance Step 4: | ||
- | C. REFER to 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-SAT Hi-Hi UNSAT Standard: | ||
N/A Refers to 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 5: | |||
2-AOI-66-2 4.0 OPERATOR ACTIONS 4.1 Immediate Actions Critical Step | |||
[1] IF scram has not occurred, THEN SAT PERFORM the following: | |||
UNSAT | |||
[1.1] IF core flow is above 60%, THEN N/A REDUCE core flow to between 50-60%. | |||
Standard: | |||
Reduced core flow to between 50-60% with recirc system. | |||
Performance Step 6: | |||
[1.2] MANUALLY SCRAM the Reactor. (Reference 2-AOI-100-1). | |||
Standard: | Standard: | ||
Critical Step | |||
* Depresses both SCRAM Pushbuttons | |||
* Places mode switch in shutdown SAT | |||
* Verifies All Rods in | |||
* Performs a Scram Announcement UNSAT o Rx Mode Switch Position: Shutdown N/A o Rod Position: All Full In o Reactor Water Level ____ & Trend ___ | |||
o Reactor Pressure ____ & Trend ___ | |||
o MSIV Position: OPEN o Rx Power: <5% | |||
Examiner Note: The scram report and referring to 2-AOI-100-1 are not considered critical. | |||
7 | |||
- | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT CUE: Proceed with subsequent actions of 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 7: | |||
4.2 Subsequent Actions | |||
[1] IF OFFGAS SYSTEM ISOLATION VALVE, 2-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN SAT DISENGAGE 2-FCV-066-0028 mechanical restraint by UNSAT rotating the restraining handwheel fully in the counterclockwisedirection, locally at the Stack. (Otherwise N/A N/A) | |||
Job Performance Measure (JPM) | |||
-AOI-66-2, Off-gas Post-treatment Radiation Hi | |||
-Hi-Hi Performance Step 7: | |||
[1] | |||
-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN DISENGAGE 2-FCV-066-0028 mechanical restraint by rotating the restraining handwheel fully in the | |||
Standard: | Standard: | ||
Verifies 2-FCV-66-28 is closed at panel 9 | Verifies that 2-FCV-066-0028 in NOT mechanically restrained. | ||
-53 by Verifying RED light above handswitch extinguished and GREEN light above handswitch illuminated. (May have already verified valve closed from the ARP). | Cue: 2-FCV-066 is NOT mechanically restrained. | ||
Performance Step 8: | |||
[3] | [2] VERIFY CLOSED OFFGAS SYSTEM ISOLATION VALVE, Critical Step 2-FCV-66-28 on Panel 2-9-53 or locally. | ||
Monitored radiation levels at Panel 9 | SAT Standard: | ||
-11. | UNSAT Verifies 2-FCV-66-28 is closed at panel 9-53 by Verifying RED light above handswitch extinguished and GREEN light above N/A handswitch illuminated. (May have already verified valve closed from the ARP). | ||
Examiner Note: May have already verified valve closed from the ARP Performance Step 9: | |||
[3] MONITOR area radiation levels at Panel: 2-9-11. SAT Standard: UNSAT Monitored radiation levels at Panel 9-11. N/A Cue: Another operator will monitor and evaluate Area Radiation Levels. | |||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-1. | STEP / STANDARD SAT / UNSAT Performance Step 10: | ||
[4] REFER TO EPIP-1 for emergency classification level and SAT response. | |||
UNSAT Standard; N/A Notifies SM to implement EPIP-1. | |||
Cue: The Shift Manager is implementing the EPIPs as needed. | |||
Performance Step 11: | Performance Step 11: | ||
[5] | [5] MONITOR the following parameters: | ||
A. MAIN STEAM LINE RADIATION, 2 | A. MAIN STEAM LINE RADIATION, 2-RR-90-135, Panel 2-9-2. | ||
-RR-90-135, | B. OFFGAS PRETREATMENT RADIATION 2-RR 157, Pnl 2-9-2. SAT C. OFFGAS POST-TREATMENT RADIATION 2RR- UNSAT 90-265, Pnl 2-9-2 N/A D. STACK GAS RADIATION, 0-RR-90-147, Unit 1 Panel 1-9-2. | ||
B. OFFGAS PRETREATMENT RADIATION 2 | Standard; Monitors 90-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147. | ||
-RR | Cue: As Unit 1 Operator, Stack Gas Radiation, 0-RR-90-147 is reading 5X10E6 cps. | ||
- | 9 | ||
-RR-90-147, Unit 1 Panel 1-9-2. Standard; Monitors | |||
-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147. | |||
-RR-90-147 is reading 5X10E6 cps. | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
[6] | STEP / STANDARD SAT / UNSAT Performance Step 12: | ||
-RR-90-266 on panel 2 2, THEN | [6] IF after five minutes from scram the Offgas Post Treatment activity is not less than 6 x 10E5 cps as indicated on OFFGASRADIATION recorder 2-RR-90-266 on panel 2 Critical Step 2, THEN SAT CLOSE all Main Steam Isolation Valves and Main Steam LineDrain Valves, 2-FCV-1-55 and 2-FCV-1-56. | ||
-FCV-1-55 and 2-FCV-1-56. Standard: | UNSAT Standard: | ||
-Gas Post Treatment activity is >6 X | N/A Recognizes that the Off-Gas Post Treatment activity is >6 X 10E5 and closes all Main Steam Isolation Valves and Main Steam Line Drain Valves (2-FCV-1-55/56) | ||
-FCV-1-55/56) | Cue: The Unit has been scrammed for 5 minutes. | ||
Acknowledge closing of MSIVs. | * Acknowledge closing of MSIVs. | ||
Examiner Note: | Examiner Note: Closing 1-55 and 1-56 is not considered critical. | ||
Closing 1-55 and 1-56 is not considered critical. | |||
Performance Step 13: | Performance Step 13: | ||
NOTE Placing additional Stack Dilution Air Fans in service should keep 0-RM-90-147and 0-RM-90-148 on scale. | |||
[7] PLACE STACK DILUTION FAN SEL control switch, SAT 2-XS-66-29, Panel 2-9-8, in OFF. | |||
UNSAT | |||
[8] START standby STACK DILUTION FAN 2B(2A) using controlswitch, 2-HS-66-31A(29A), Panel 2-9-8. N/A Standard: | |||
Places 2-XS-66-29 in OFF and Starts standby Stack Dilution fan 2B, using 2-HS-66-31A Cue: That completes this task. | |||
STOP TIME _______ | |||
END OF TASK 10 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
Job Performance Measure (JPM) | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are the Unit 2 Operator. Unit 2 is at 100% power. | You are the Unit 2 Operator. Unit 2 is at 100% power. | ||
INITIATING CUE: | |||
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 2-XA-55-4C, window 35. | |||
11 | |||
Job Performance Measure (JPM) | |||
SITE: BFN JPM TITLE: Respond to Off-Gas Post Treatment Radiation HI-HI-HI JPM NUMBER: 190 U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-066-AB-02 -Respond to Off-Gas Post Treatment TASK NUMBER / TASK TITLE(S): | |||
Radiation Hi-Hi-Hi K/A RATINGS: RO 2.9 SRO 3.2 271000 Offgas System: A2.16;Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the K/A STATEMENT: | |||
consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2) | |||
RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: N/A TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
Job Performance Measure (JPM) | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
Respond to Off | Validated by: | ||
-Gas Post Treatment Radiation HI | Validator Date Approved by: | ||
-HI-HI JPM NUMBER: | Site Training Management Date Approved by: | ||
190 U3 REVISION: 0 | Site Training Program Owner Date 1 | ||
SRO STA UO NAUO | |||
U-066-AB-02 -Respond to Off | |||
-Gas Post Treatment Radiation Hi | |||
-Hi-Hi K/A RATINGS: | |||
RO 2.9 | |||
271000 Offgas System | |||
: A2.16;Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2) | |||
N/A SAFETY FUNCTION: | |||
9 | |||
In-Plant | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
TASK STANDARD: | Job Performance Measure (JPM) | ||
Respond to Off | OPERATOR: ________________________________ JPM Number: 190 RO SRO DATE: _______ | ||
-Gas Post Treatment Radiation HI | TASK STANDARD: Respond to Off-Gas Post Treatment Radiation HI-HI-HI per 3-AOI-66-2 and/or 3-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: 3-AOI-66-2, 3-ARP-9-4C/35 VALIDATION TIME: 15 Minutes PERFORMANCE TIME: | ||
-HI-HI per 3-AOI-66-2 and/or 3-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: | COMMENTS: | ||
3-AOI-66-2, 3-ARP-9-4C/35 VALIDATION TIME: 15 Minutes | Additional comment sheets attached? YES ___ NO ___ | ||
COMMENTS: | RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | ||
SIGNATURE: ___________________________ DATE: __________ | |||
Additional comment sheets attached? | EXAMINER 2 | ||
RESULTS: SATISFACTORY ____ | |||
UNSATISFACTORY ____ | |||
(Retain entire JPM for records) | |||
SIGNATURE: ___________________________ | |||
DATE: __________ | |||
EXAMINER | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
SIMULATOR SETUP IC 28 Exam IC 288 | |||
: 1. Reset to IC 28 Console 2. Fire Manual Trigger 2 Operator 3. Fire Manual Trigger 1 Instructions 4. Station 2nd operator to respond to alarms Malfunctions Description Event Severity Delay Initial set TH23 FUEL CLADDING 1 50 N/A YES DAMAGE RM14C OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-265A RM14D OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-266A Remotes Description Event Severity Delay Initial set OG06 Bypass FCV-66-28 2 N/A N/A BYP Post Treatment Hi-Hi-Hi Rad Isol Overrides Description Event Severity Delay Initial set ZAORI9014A RX BLDG AREA 1 2.5 N/A YES RAD ZAORI9017A RX BLDG AREA 1 2.6 N/A YES RAD ZAORM90265A 90-265 METER 1 6.0 N/A YES UPSCALE ZAORM90266A 90-266 METER 1 6.0 N/A YES UPSCALE ZAORR90135R1 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90135R2 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZLORM90265A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_2 90-265 DRAW LITE 1 N/A N/A YES 3 | |||
Job Performance Measure (JPM) | |||
ZLORM90265A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_4 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_4 90-265 DRAW LITE 1 N/A N/A YES XA553A5 OG PRETREAT 1 N/A N/A YES RAD HI XA553A6 STACK GAS RAD 1 N/A N/A YES HI HI XA553A7 MSL RAD HI 1 N/A N/A YES XA553A13 STACK GAS RAD 1 N/A N/A YES HI XA553A27 MSL RAD HI HI 1 N/A N/A YES XA554C26 CARBON BED 1 N/A N/A YES VAULT RAD HI XA554C27 OG ANNUAL 1 N/A N/A YES RELEASE LIMIT EXCEEDED XA554C33 OG POST TREAT 1 N/A N/A YES RAD HI XA554C34 OG POST TREAT 1 N/A N/A YES RAD HI HI XA554C35 OG POST TREAT 1 N/A N/A YES RAD HI HIHI ZDIHS6628 66-28 VALVE 1 N/A N/A YES CLOSED ZAORR90265R1 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90265R2 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZAORR90160R1 OG PRETREAT 1 -2.0 N/A YES RECORDER UPSCALE XA554B2 RWCU FILTER 1 N/A N/A YES INLET CNDT HIGH Schedule File(s): JPM 190 U3 OG Post treat Rad HI HIHI 4 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are the Unit 3 Operator. Unit 3 is at 100% power. | You are the Unit 3 Operator. Unit 3 is at 100% power. | ||
INITIATING CUE: | |||
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 3-XA-55-4C, window 35. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / UNSAT Performance Step 1: | |||
SAT When directed, identify/obtain copy of ARP-9-4C, window 35. | |||
UNSAT Standard: | |||
N/A Obtains copy of 3-ARP-9-4C, window 35 Examiner Note: Candidate may recognize the annunciator as an entry condition and go directly to 3-AOI-66-2. In that event, continue at Performance Step 5. | |||
Performance Step 2: | |||
3-ARP-9-4C window 35 Operator Action: | |||
A. VERIFY alarm condition on the following | |||
* OFFGAS POST-TREATMENT RADIATION recorder, SAT 3-RR-90-265 on Panel 3-9-2. | |||
* OG POST-TREATMENT CHAN A RAD MON RTMR UNSAT radiationmonitor, 3-RM-90-266A on Panel 3-9-10. | |||
* OG POST-TREATMENT CHAN B RAD MON RTMR N/A radiationmonitor, 3-RM-90-265A on Panel 3-9-10. | |||
Standard: | |||
Verified alarm condition on 3-RR-90-265 and 3-RM-265/266. | |||
Performance Step 3: | |||
B. VERIFY OFF-GAS SYSTEM ISOLATION VALVE, 3-FCV- Critical Step 66-28 has the Mechanical Restraint DISENGAGED and 3-FCV-66-28 isCLOSED. SAT Standard: UNSAT Takes handswitch 3-FCV-66-28 to close and observes green light N/A illuminated and red light out. | |||
Cue: If asked, the Offgas Isolation Valve, 3-FCV-66-28 is NOT mechanically restrained. | |||
6 | |||
Job Performance Measure (JPM) | |||
- | STEP / STANDARD SAT / UNSAT Performance Step 4: | ||
C. REFER to 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi SAT Standard: UNSAT Refers to 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi N/A Performance Step 5: | |||
3-AOI-66-2 4.0 OPERATOR ACTIONS 4.1 Immediate Actions Critical Step | |||
[1] IF scram has not occurred, THEN SAT PERFORM the following: | |||
UNSAT | |||
[1.1] IF core flow is above 60%, THEN N/A REDUCE core flow to between 50-60%. | |||
Standard: | |||
Reduced core flow to between 50-60% with recirc system. | |||
Performance Step 6: | |||
[1.2] MANUALLY SCRAM the Reactor. (Reference 3-AOI-100-1). | |||
Standard: | Standard: | ||
Critical Step | |||
* Depresses both SCRAM Pushbuttons | |||
* Places mode switch in shutdown SAT | |||
* Verifies All Rods in | |||
* Performs a Scram Announcement UNSAT o Rx Mode Switch Position: Shutdown N/A o Rod Position: All Full In o Reactor Water Level ____ & Trend ___ | |||
o Reactor Pressure ____ & Trend ___ | |||
o MSIV Position: OPEN o Rx Power: <5% | |||
Examiner Note: The scram report and referring to 3-AOI-100-1 are not considered critical. | |||
7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT CUE: Proceed with subsequent actions of 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 7: | |||
4.2 Subsequent Actions | |||
[1] IF OFFGAS SYSTEM ISOLATION VALVE, 3-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN SAT DISENGAGE3-FCV-066-0028 mechanical restraint by UNSAT rotating the restraining handwheel fully in the counterclockwisedirection, locally at the Stack. (Otherwise N/A N/A) | |||
Job Performance Measure (JPM) | |||
-AOI-66-2, Off-gas Post-treatment Radiation Hi | |||
-Hi-Hi Performance Step 7: | |||
[1] | |||
Standard: | Standard: | ||
Verifies 3-FCV-66-28 is closed at panel 9 | Verifies that 3-FCV-066-0028 in NOT mechanically restrained. | ||
-53 by Verifying RED light above handswitch extinguished and GREEN light above handswitch illuminated. (May have already verified valve closed from the ARP). | Cue: 3-FCV-066 is NOT mechanically restrained. | ||
Performance Step 8: | |||
[3] | [2] VERIFY CLOSED OFFGAS SYSTEM ISOLATION VALVE, Critical Step 3-FCV-66-28 on Panel 3-9-53 or locally. | ||
3-9-11. Standard: | SAT Standard: | ||
Monitored radiation levels at Panel 9 | UNSAT Verifies 3-FCV-66-28 is closed at panel 9-53 by Verifying RED light above handswitch extinguished and GREEN light above N/A handswitch illuminated. (May have already verified valve closed from the ARP). | ||
-11. | Examiner Note: May have already verified valve closed from the ARP Performance Step 9: | ||
SAT | |||
[3] MONITOR area radiation levels at Panel: 3-9-11. | |||
UNSAT Standard: | |||
N/A Monitored radiation levels at Panel 9-11. | |||
Cue: Another operator will monitor and evaluate Area Radiation Levels. | |||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-1. | STEP / STANDARD SAT / UNSAT Performance Step 10: | ||
[4] REFER TO EPIP-1 for emergency classification level and SAT response. | |||
UNSAT Standard; N/A Notifies SM to implement EPIP-1. | |||
Cue: The Shift Manager is implementing the EPIPs as needed. | |||
Performance Step 11: | Performance Step 11: | ||
[5] | [5] MONITOR the following parameters: | ||
A. MAIN STEAM LINE RADIATION, 3-RR-90-135, | A. MAIN STEAM LINE RADIATION, 3-RR-90-135, Panel 3-9-2. | ||
B. OFFGAS PRETREATMENT RADIATION 3-RR | B. OFFGAS PRETREATMENT RADIATION 3-RR 157, Pnl3-9-2. SAT C. OFFGAS POST-TREATMENT RADIATION 3-RR- UNSAT 90-265, Pnl3-9-2 N/A D. STACK GAS RADIATION, 0-RR-90-147, Unit 1 Panel 1-9-2. | ||
-RR-90-147, Unit 1 Panel 1-9-2. Standard; Monitors | Standard; Monitors 90-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147. | ||
-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147. | Cue: As Unit 1 Operator, Stack Gas Radiation, 0-RR-90-147 is reading 5X10E6 cps. | ||
-RR-90-147 is reading 5X10E6 cps. | 9 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
[6] | STEP / STANDARD SAT / UNSAT Performance Step 12: | ||
-Gas Post Treatment activity is >6 X | [6] IF after five minutes from scram the Offgas Post Treatment activity is not less than 6 x 10E5 cps as indicated on OFFGASRADIATION recorder 3-RR-90-265 on panel 3 2, THEN Critical Step CLOSE all Main Steam Isolation Valves and Main Steam SAT LineDrain Valves, 3-FCV-1-55 and 3-FCV-1-56. | ||
Acknowledge closing of MSIVs. | UNSAT Standard: | ||
N/A Recognizes that the Off-Gas Post Treatment activity is >6 X 10E5 and closes all Main Steam Isolation Valves and Main Steam Line Drain Valves (3-FCV-1-55/56) | |||
Cue: The Unit has been scrammed for 5 minutes. | |||
* Acknowledge closing of MSIVs. | |||
Examiner Note: Closing 1-55 and 1-56 is not considered critical. | Examiner Note: Closing 1-55 and 1-56 is not considered critical. | ||
Performance Step 13: | Performance Step 13: | ||
NOTE Placing additional Stack Dilution Air Fans in service should keep 0-RM-90-147and 0-RM-90-148 on scale. | |||
NOTE Placing additional Stack Dilution Air Fans in service should keep 0 | [7] PLACE STACK DILUTION FAN SEL control switch, SAT 3-XS-66-29, Panel 3-9-8, in OFF. | ||
-RM-90-147and 0-RM-90-148 on scale. | UNSAT | ||
[7] | [8] START standby STACK DILUTION FAN 3B(3A) using controlswitch, 3-HS-66-31A(29A), Panel 3-9-8. N/A Standard: | ||
[8] | Places 3-XS-66-29 in OFF and Starts standby Stack Dilution fan 3B, using 3-HS-66-31A Cue: That completes this task. | ||
Places 3-XS-66-29 in OFF and Starts standby Stack Dilution fan 3B, using 3-HS-66-31A | |||
STOP TIME ________ | STOP TIME ________ | ||
END OF TASK | END OF TASK 10 | ||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are the Unit 3 Operator. Unit 3 is at 100% power. | You are the Unit 3 Operator. Unit 3 is at 100% power. | ||
INITIATING CUE: | |||
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 3-XA-55-4C, window 35. | |||
11 | |||
Job Performance Measure (JPM) | |||
SITE: BFN JPM TITLE: AUTOMATIC START FAILURE OF A & C FIRE PUMPS JPM NUMBER: 673 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-026-NO-01/ MONITOR AUTO START OF FIRE TASK NUMBER / TASK TITLE(S): | |||
PUMP K/A RATINGS: RO: 3.4 SRO: 3.4 286000 Fire Protection System A2.08; Ability to (a) predict the impacts of the following on the FIRE PROTECTION SYSTEM; K/A No. &STATEMENT: and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Failure to actuate when required RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 8 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Job Performance Measure (JPM) | Validated by: | ||
AUTOMATIC START FAILURE OF A & C FIRE | Validator Date Approved by: | ||
673 REVISION: | Site Training Management Date Approved by: | ||
SRO STA UO NAUO | Site Training Program Owner Date 1 | ||
U-026-NO-01/ MONITOR AUTO START OF FIRE PUMP | |||
RO: | |||
286000 Fire Protection System | |||
Risk Significant SAFETY FUNCTION: | |||
8 | |||
In-Plant | |||
ALTERNATE PATH (Y/N) | |||
Developed by: | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _673A___ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to manually start A, B and C Fire Pumps. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 0-OI-26 VALIDATIONTIME:__15 min PERFORMANCE TIME: | ||
0-OI-26 | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 04/28/15 All Initial issue 3 | |||
Job Performance Measure (JPM) | |||
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 1. | |||
* The Reactor Power at 70% | |||
* A Fire Exists on B Reactor Feed Pump Lube Oil Reservoir. | |||
* Fire OPS has been dispatched to the scene. | |||
* Fire Pump B Tagged Out for Maintenance | |||
* A and C Fire Pumps failed to Auto Start. | |||
INITIATING CUES: | |||
The US directs you to start A and C Electric Fire Pumps per 0-OI-26 section 5.4. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-XS-26-1 in EMERGENCY position, at the respective switchgear. | START TIME: | ||
Pump Board Compt A 4160V Shutdown Bd A 11 C 4160V Shutdown Bd C 10 | STEP / STANDARD SAT / UNSAT Step 1: | ||
-XS-26-3 in EMERGENCY position at 4160 Shutdown Board A, Compartment | [1] PLACE the FIRE PUMP A TRANSFER switch, 0-XS-26-1 in EMERGENCY position, at the respective switchgear. | ||
Critical Step Pump Board Compt A 4160V Shutdown Bd A 11 SAT C 4160V Shutdown Bd C 10 UNSAT Standard: | |||
11 | N/A Simulates placing FIRE PUMP A TRANSFER switch 0-XS-26-3 in EMERGENCY position at 4160 Shutdown Board A, Compartment 11 CUE: FIRE PUMP A TRANSFER switch 0-XS-26-1 is in the EMERGENCY position Step 2: | ||
-XS-26-1 is in the EMERGENCY position Step 2: | |||
Critical Step | Critical Step | ||
[2] CLOSE the breaker by placing the FIRE PUMP A CONTROL switch, 0-HS-26-1C to CLOSE. SAT Standard: UNSAT Simulates placing FIRE PUMP A CONTROL switch, 0-HS-26-1C N/A to CLOSE position. | |||
SAT | CUE: Breaker Red indicating light is ON with Green and Amber lights are OFF. | ||
Breaker Flag indicates CLOSED with Charging Spring indicating CHARGED. | |||
Step 3: | Step 3: | ||
[3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. Standard | [3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. SAT Standard UNSAT VERIFIES pump ammeter at breaker indicates between 25 and N/A 40 amps. | ||
CUE: FIRE PUMP A ammeter at breaker indicates 30 amps. | |||
5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Standard | Step 4: | ||
[1] PLACE the FIRE PUMP C TRANSFER switch, 0 | [4] PLACE the NORM/EMERG Switch in NORMAL. | ||
-XS-26-3 in EMERGENCY position, at the respective switchgear. | SAT Standard UNSAT PLACES the NORM/EMERG Switch in NORMAL for FIRE N/A PUMP A. | ||
Pump Board Compt A 4160V Shutdown Bd A 11 C 4160V Shutdown Bd C 10 | CUE: FIRE PUMP A NORM/EMERG Switch is in NORMAL Step 5: | ||
-XS-26-3 in EMERGENCY position at 4160 Shutdown Board C, Compartment | [1] PLACE the FIRE PUMP C TRANSFER switch, 0-XS-26-3 in EMERGENCY position, at the respective switchgear. | ||
Critical Step Pump Board Compt A 4160V Shutdown Bd A 11 SAT C 4160V Shutdown Bd C 10 UNSAT Standard: | |||
10 | N/A Simulates placing FIRE PUMP C TRANSFER switch 0-XS-26-3 in EMERGENCY position at 4160 Shutdown Board C, Compartment 10 CUE: FIRE PUMP C TRANSFER switch 0-XS-26-3 is in the EMERGENCY position Step 5: | ||
Critical Step | |||
-XS-26-3 is in the EMERGENCY position Step 5: | |||
[2] CLOSE the breaker by placing the FIRE PUMP C CONTROL switch, 0-HS-26-3C to CLOSE. | [2] CLOSE the breaker by placing the FIRE PUMP C CONTROL switch, 0-HS-26-3C to CLOSE. | ||
Standard: | SAT Standard: | ||
-HS-26-3C to CLOSE position. | UNSAT Simulates placing FIRE PUMP C CONTROL switch, 0-HS-26-3C N/A to CLOSE position. | ||
CUE: Breaker Red indicating light is ON with Green and Amber lights are OFF. | |||
Breaker Flag indicates CLOSED with Charging Spring indicating CHARGED. | |||
6 | |||
Job Performance Measure (JPM) | |||
Step 6: | |||
Job Performance Measure (JPM) | [3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. SAT Standard UNSAT VERIFIES pump ammeter at breaker indicates between 25 and N/A 40 amps. | ||
CUE: FIRE PUMP C ammeter at breaker indicates 30 amps. | |||
Step 7: | Step 7: | ||
[4] PLACE the NORM/EMERG Switch in NORMAL. | [4] PLACE the NORM/EMERG Switch in NORMAL. | ||
Standard | SAT Standard UNSAT PLACES the NORM/EMERG Switch in NORMAL for FIRE N/A PUMP C. | ||
CUE: FIRE PUMP C NORM/EMERG Switch is in NORMAL and this completes the JPM. | |||
Termination Criteria: When two Fire Pumps are in service the JPM is complete. | |||
STOP TIME: | STOP TIME: | ||
7 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 1. | |||
* The Reactor Power at 70% | |||
* A Fire Exists on B Reactor Feed Pump Lube Oil Reservoir. | |||
* Fire OPS has been dispatched to the scene. | |||
* Fire Pump B Tagged Out for Maintenance | |||
* A and C Fire Pumps failed to Auto Start. | |||
INITIATING CUES: | |||
The US directs you to start A and C Electric Fire Pumps per 0-OI-26 section 5.2. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
ALIGNING EMERGENCY EECW MAKEUP TO SPENT SITE: BFN JPM TITLE: | |||
674 REVISION: 0 | FUEL POOL JPM NUMBER: 674 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-95/ Make-Up To SFP By EECW With TASK NUMBER / TASK TITLE(S): | ||
SRO STA UO NAUO | Fire Hose (Internal Make-Up) | ||
U-000-EM-95/ Make-Up To SFP By EECW With Fire Hose (Internal Make | K/A RATINGS: RO: 3.1 SRO: 3.3 233000 Fuel Pool Cooling and Clean-up; A2.02; Ability to (a) predict the impacts of the following on the FUEL POOL COOLING AND CLEAN-UP ; and (b) based on those K/A No. &STATEMENT: | ||
-Up) | predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Low pool level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | ||
RO: | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
233000 Fuel Pool Cooling and Clean | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
-up; A2.02; Ability to (a) predict the impacts of the following on the FUEL POOL COOLING AND | Validated by: | ||
Low pool level RELATED PRA INFORMATION: | Validator Date Approved by: | ||
Risk Significant SAFETY FUNCTION: | Site Training Management Date Approved by: | ||
9 | Site Training Program Owner Date 1 | ||
ALTERNATE PATH (Y/N) | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: __674__ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to align either North or South Headers of EECW to Unit 2 Spent Fuel Pool. | |||
Operator Fundamental evaluated: | |||
OF-2 Controlling plant evolutions and indications closely. | OF-2 Controlling plant evolutions and indications closely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-78-1 VALIDATION TIME: 25 min PERFORMANCE TIME: | ||
2-AOI-78-1 VALIDATION TIME: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 3 | |||
Job Performance Measure (JPM) | |||
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
* The Reactor is in cold shutdown | |||
* The Unit 2 Spent Fuel Pool water level is lowering. | |||
* Fire Protection is available to assist INITIATING CUES: | |||
The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3]. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
NORTH HDR SPLY TO EMER FUEL POOL MU, 1 | START TIME: | ||
-SHV-067-0792. SOUTH HDR SPLY TO EMER FUEL POOL MU, 1 | STEP / STANDARD SAT / UNSAT Step 1: | ||
-SHV-067-0793. Standard: | NOTES | ||
-SHV-067-0793 by demonstrating opening each valve | : 1) Hose straps are staged at the hoses at the following locations: | ||
* Unit 1/Unit 2 Reactor Bldg Stairwell, El. 621, R6 U Line (placed on hose to carry weight of charged hose lines). | |||
-SHV-067-0792 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1 | * Hose reel on the Refuel Floor, El. 664, R6 U Line (for use in securing hose ends as needed). | ||
-SHV-067-0793 is OPEN | : 2) Additional hose is stored in a cabinet located in Unit 1/Unit 2 Elevator Room, Reactor Bldg, El 595. | ||
Hoses are already connected, no tools required. | Critical Step CAUTION Performance of this attachment will degrade water chemistry in the SAT Spent Fuel Pool. | ||
UNSAT | |||
[3] UNLOCK and OPEN the following valves: | |||
N/A | |||
* NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792. | |||
* SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793. | |||
Standard: | |||
Simulates opening NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792 and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793 by demonstrating opening each valve counter-clockwise and breaking seal. | |||
CUE: NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793 is OPEN Located in stairwell between elevation 565 ft and 593 ft. Hoses are already connected, no tools required. | |||
5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 3: | |||
[4] VERIFY charged hoses in stairwell are not obstructing stairway access and/or kinked. | |||
SAT | |||
[4.1] ADJUST hose straps, as necessary. | [4.1] ADJUST hose straps, as necessary. | ||
Standard: | UNSAT Standard: | ||
Hoses are already run along the stairwell. Applicant should verify hoses not kinked and connected. | N/A VERIFIES hoses in stairwell are not kinked Note to Examiner: Hoses are already run along the stairwell. Applicant should verify hoses not kinked and connected. | ||
Step 4: | Step 4: | ||
-SHV-067-0796 and route to Unit 2 Spent Fuel Pool (El 664 | [5] VERIFY hose connected from NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and route to Unit 2 Spent Fuel Pool Critical Step (El 664, Refuel Floor, R6-U Line). | ||
-U Line). Standard: | SAT Standard: | ||
-SHV-067-0796 and route to Unit 2 Spent Fuel Pool (El 664 | UNSAT VERIFY hose connected from NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and route to Unit 2 Spent N/A Fuel Pool (El 664, Refuel Floor, R6-U Line). | ||
-U Line). | Note to Examiner: Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. Hoses are already connected, no tools required. | ||
Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. | |||
Hoses are already connected, no tools required. | |||
Location: Refuel Floor Elevation 664 ft, R U Line. | Location: Refuel Floor Elevation 664 ft, R U Line. | ||
Step 5: | Step 5: | ||
-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664 | [6] VERIFY hose connected from SOUTH HDR SPLY TO EMER Critical Step FUEL POOL MU, 1-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664, Refuel Floor, R6-U Line) | ||
-U Line) | SAT Standard: | ||
-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664 | UNSAT VERIFY hose connected from SOUTH HDR SPLY TO EMER N/A FUEL POOL MU, 1-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664, Refuel Floor, R6-U Line) 6 | ||
-U Line) | |||
Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. | Job Performance Measure (JPM) | ||
Hoses are already connected, no tools required. | STEP / STANDARD SAT / UNSAT Note to Examiner: Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. Hoses are already connected, no tools required. | ||
Location: Refuel Floor Elevation 664 ft, R U Line. | Location: Refuel Floor Elevation 664 ft, R U Line. | ||
Step 6: | Step 6: | ||
NORTH HDR SPLY TO EMER FUEL POOL MU, 1 | [7] VERIFY OPEN the following valves (El 664, Refuel Floor, R6 U Line): | ||
-SHV-067-0796. SOUTH HDR SPLY TO EMER FUEL POOL MU, 1 | * NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-Critical Step 0796. | ||
-SHV-067-0797. Standard: | SAT | ||
-SHV-067-0797 by demonstrating opening each valve | * SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797. | ||
UNSAT Standard: | |||
-SHV-067-0796 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1 | N/A Simulates opening NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797 by demonstrating opening each valve counter-clockwise. | ||
-SHV-067-0797 is OPEN | CUE: NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797 is OPEN Location: Refuel Floor Elevation 664 ft, R U Line. | ||
Step 7: | Step 7: | ||
Standard: | [8] VERIFY charged hoses on the Refuel Floor are not kinked. | ||
SAT Standard: UNSAT VERIFY charged hoses on the Refuel Floor are not kinked N/A Termination Criteria: NORTH and SOUTH Header are aligned then the JPM is complete. State another operator will perform the remaining steps. | |||
STOP TIME: | |||
7 | |||
Job Performance Measure (JPM) | |||
Job Performance Measure (JPM) | Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | ||
INITIAL CONDITIONS: | |||
INITIAL CONDITIONS: | You are an Operator on Unit 2. | ||
* The Reactor is in cold shutdown | |||
You are an Operator on Unit 2. The Reactor is in cold shutdown The Unit 2 Spent Fuel Pool water level is lowering. | * The Unit 2 Spent Fuel Pool water level is lowering. | ||
Fire Protection is available to assist INITIATING CUES | * Fire Protection is available to assist INITIATING CUES: | ||
: | |||
The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3]. | The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3]. | ||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START UP AND SYNCHRONIZE UNIT 3 PREFERRED MMG SET JPM NUMBER: | START UP AND SYNCHRONIZE UNIT 3 PREFERRED SITE: BFN JPM TITLE: | ||
307 REVISION: 6 | MMG SET JPM NUMBER: 307 REVISION: 6 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): S-57C-NO-04 K/A RATINGS: RO: 2.5 SRO: 2.9 262002 Uninterruptable Power Supply (A.C./D.C.) A1.02; Ability to predict and/or monitor changes in parameters associated with K/A No. &STATEMENT: | ||
SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): | operating the UNINTERRUPTABLE POWER SUPPLY (A.C./D.C.) controls including: Motor generator outputs RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 6 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | ||
S-57C-NO-04 | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
RO: | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
262002 Uninterruptable Power Supply (A.C./D.C.) A1.02; Ability to predict and/or monitor changes in parameters associated with operating the UNINTERRUPTABLE POWER SUPPLY (A.C./D.C.) controls including: | Validated by: | ||
Motor generator outputs RELATED PRA INFORMATION: | Validator Date Approved by: | ||
Risk Significant SAFETY FUNCTION: | Site Training Management Date Approved by: | ||
6 | Site Training Program Owner Date 1 | ||
In-Plant | |||
ALTERNATE PATH (Y/N) | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _307___ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to Start-up and synchronize Unit Preferred MMG Set Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant Evolutions Precisely PRA: NA REFERENCES/PROCEDURES NEEDED: | OF-2 Controlling plant Evolutions Precisely PRA: NA REFERENCES/PROCEDURES NEEDED: 0-OI-57C VALIDATIONTIME: 25 min PERFORMANCE TIME: | ||
0-OI-57C VALIDATIONTIME: 25 min | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 1 10/26/94 ALL GENERAL REVISION 2 05/07/95 ALL GENERAL REVISION FORMAT, PROCEDURE REVISION, ADDED 3 10/15/97 ALL PLANT WORK EXPECTATIONS TOUCH STAAR, SAFETY, AND 3-WAY COMM. | |||
PROCEDURE REVISION, FORMAT 4 11/10/99 ALL DOCUMENT 5 10/03/01 ALL PROCEDURE REVISION 6 04/28/15 ALL UPDATE TO NEW FORMAT 3 | |||
-WAY COMM. 4 11/10/99 ALL | |||
Job Performance Measure (JPM) | |||
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is in cold shutdown | |||
* The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1. | |||
* Maintenance has been completed on the Unit 3 Unit Preferred MMG Set. | |||
INITIATING CUES: | |||
The SM directs you to start up and synchronize the Unit 3 Unit Preferred MMG Set as directed by 0-OI-57C per section 5.5 step 5.5[16]. | |||
NOTE: PERFORMER WILL NEED GGMKA KEY. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START TIME: | |||
[16] PLACE UNIT 3 MMG OPERATING MODE, 3 | STEP / STANDARD SAT / UNSAT Step 1: | ||
-HS-252-02AB in AUTO. Standard: | NOTE Steps 5.5[16] through 5.5[26] are performed from Battery Board Room 2 UNIT PFD Sync. & Speed Control Panel. Critical Step SAT | ||
-HS-252-02AB in AUTO. | [16] PLACE UNIT 3 MMG OPERATING MODE, 3-HS-252-02AB in AUTO. | ||
UNSAT Standard: | |||
N/A VERIFIED/SIMULATED PLACING the Unit 3 MMG SET OPERATING MODE 3-HS-252-02AB in AUTO. | |||
Cue: The Unit 3 MMG SET OPERATING MODE 3-HS-252-02AB is in AUTO position. | |||
-HS-252-02AB is in AUTO position. | |||
Step 2: | Step 2: | ||
Critical Step | Critical Step | ||
[17] PLACE UNIT 3 MMG LOCAL-REMOTE CONTROL, 3-XS-252-02A in REMOTE. | |||
SAT UNSAT N/A Cue: | SAT Standard: | ||
-REMOTE CONTROL 3 | UNSAT SIMULATED PLACING the Unit 3 MMG SET LOCAL-REMOTE N/A CONTROL 3-XS-252-02A in the REMOTE position. | ||
-HS-252-02A is in the REMOTE position. | Cue: The Unit 3 MMG SET LOCAL-REMOTE CONTROL 3-HS-252-02A is in the REMOTE position. | ||
Step 3: | Step 3: | ||
[18] PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH SS | [18] PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE Critical Step SYNC SWITCH SS-7, 3-HS-252-03/SS-7 in ON. | ||
-7, 3-HS-252-03/SS-7 in ON. Standard: | SAT Standard: | ||
-7, 3-HS-252-03/SS-7, in the ON position. | UNSAT SIMULATED PLACING UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 3-HS-252-03/SS-7, in the ON N/A position. | ||
5 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Cue: The Unit 3 PFD SYSTEM GENERATOR SOURCE SYNC SS-7, SWITCH 3-HS-252-003/SS-7 is in the ON position. | |||
Job Performance Measure (JPM) | Step 4: | ||
-7, SWITCH 3-HS-252-003/SS-7 is in the ON position. Step 4: | NOTE MMG voltage and hertz are read as INCOMING. | ||
Critical Step | Critical Step | ||
[19] MATCH Incoming to Running AC volts using UNIT 3 MMG VOLTAGE ADJUST, 3-HS-252-02CD. SAT Standard: UNSAT SIMULATED MANIPULATING UNIT 3 MMG VOLTAGE ADJUST, N/A 3-HS 252-02CD until cued that incoming and running AC volts are matched. | |||
Cue: INCOMING and RUNNING VOLTAGES are EQUAL at 122 Volts Step 5: | |||
[20] ADJUST MMG speed using UNIT 3 MMG FREQUENCY ADJUST, 3-HS-252-02CF to obtain a synchroscope slowly rotating in the SLOW Critical Step (counter-clockwise) direction (10 to 15 second rotation) as indicated on SYNCHROSCOPE, 0-SCP-252-000A/B. | |||
SAT Standard: | |||
UNSAT SIMULATED ADJUSTING UNIT 3 MMG FREQUENCY ADJUST N/A 3-HS-252-02CF speed control switch until cued that synchroscope indicator rotating in the counterclockwise direction at 10 to 15 seconds per revolution. | |||
Cue: State: The Initial Synchroscope indicator is standing still at the 5 oclock position. | |||
Note: If student raises frequency the state: Synchroscope indicator is rotating in the CLOCKWISE direction at 12 seconds per revolution. | |||
Note: If student lowers frequency the state: Synchroscope indicator is rotating in the COUNTERCLOCKWISE direction at 12 seconds per revolution. | |||
6 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 6: | |||
NOTES | |||
: 1) Section 5.5[21] should be performed expeditiously (within about 15 seconds) to minimize the time AC Systems are paralleled to prevent tripping the MMG set. Voltage and amps is expected to fluctuate while the AC systems are paralleled and the MMG set will trip if the AC systems are paralleled for approximately 30 seconds. | |||
Job Performance Measure (JPM) | |||
: 2) If breaker 1001 trips, it must be reset with reset push button on the respective Unit Battery Board, Panel 10. | : 2) If breaker 1001 trips, it must be reset with reset push button on the respective Unit Battery Board, Panel 10. | ||
CAUTIONS 1) Voltage Oscillations may occur during Bus Power Transfers. | CAUTIONS | ||
: 1) Voltage Oscillations may occur during Bus Power Transfers. | |||
These oscillations are caused when two Power Supplies having separate Voltage Regulators try to maintain voltage control. | These oscillations are caused when two Power Supplies having separate Voltage Regulators try to maintain voltage control. | ||
Therefore, the time the Power Supplies are paralleled should be minimized as follows:[PER 64835] | Therefore, the time the Power Supplies are paralleled should be minimized as follows:[PER 64835] | ||
When transferring Bus power supplies from one MMG to another MMG. | * When transferring Bus power supplies from one MMG to Critical Step another MMG. | ||
When transferring Bus power supplies from one MMG with the unit preferred transformer. (Unit 2 has a Voltage Regulator Transformer which makes voltage oscillations more susceptible.) | * When transferring Bus power supplies from one MMG with the SAT unit preferred transformer. (Unit 2 has a Voltage Regulator Transformer which makes voltage oscillations more UNSAT susceptible.) | ||
N/A | |||
: 2) Minimize the number of Bus power supply transfers and only transfer Bus power supplies when absolutely necessary. | : 2) Minimize the number of Bus power supply transfers and only transfer Bus power supplies when absolutely necessary. | ||
: 3) During the transfer of Bus power supplies the affiliated RPS circuit protectors 1(2)C1 and/or 1(2)C2 may trip. | : 3) During the transfer of Bus power supplies the affiliated RPS circuit protectors 1(2)C1 and/or 1(2)C2 may trip. | ||
Start of Critical Step(s) | Start of Critical Step(s) | ||
[21] WHEN SYNCHROSCOPE, 0-SCP-252-000A/B is 5 minutes prior to 12 o'clock, in the SLOW counter-clockwise direction, THEN PERFORM the following expeditiously: | |||
[21.1] CLOSE UNIT 3 BKR 1001, using 0-HS-280-003/1001. | |||
[21.2] ENSURE CLOSED UNIT 3 BKR 1001. | |||
7 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Standard( step 6 continued): | |||
-HS-252-003/1001 in the CLOSE position. | When cued synchroscope indicator at 5 minutes prior to 12 o'clock, SIMULATED PLACING 3-BKR 1001, 0-HS-252-003/1001 in the CLOSE position. | ||
NOTE: IT WOULD ASSIST THE EXAMINEE IF THE EVALUATOR WOULD USE HIS FINGER TO DEMONSTRATE INDICATOR POSITION ON THE SYNCHROSCOPE AS THE READINGS ARE ENUNCIATED. | NOTE: IT WOULD ASSIST THE EXAMINEE IF THE EVALUATOR WOULD USE HIS FINGER TO DEMONSTRATE INDICATOR POSITION ON THE SYNCHROSCOPE AS THE READINGS ARE ENUNCIATED. | ||
CUE: THE SYNCHROSCOPE INDICATOR IS AT 30 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 15 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 5 MINUTES BEFORE THE 12 O'CLOCK POSITION | CUE: THE SYNCHROSCOPE INDICATOR IS AT 30 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 15 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 5 MINUTES BEFORE THE 12 O'CLOCK POSITION. | ||
CUE: [WHEN CLOSED] UNIT 3 BREAKER 1001 BREAKER POSITION INDICATING LAMP CHANGED FROM ILLUMINATED GREEN TO ILLUMINATED RED. | |||
Step 7: | |||
[21.3] OPEN the UNIT 3)BKR 1002, using 0 | [21.3] OPEN the UNIT 3)BKR 1002, using 0-HS-280-003/1002. Critical Step End of Critical Step(s) SAT Standard: UNSAT SIMULATED UNIT 3 BKR 1002, 0-HS-282-003/1002in the OPEN N/A position. | ||
-HS-280-003/1002. | CUE: UNIT 3 BKR 1002, 0-HS-282-003/1002 IS IN THE OPEN POSITION WITH RED LIGHT ILLUMINATED. | ||
NOTE: DO NOT ALLOW THE EXAMINEE TO OPERATE THE AMMETER SELECTOR SWITCH FOR THE FOLLOWING STEP. | |||
Standard: | |||
-HS-282-003/1002 IS IN THE OPEN POSITION WITH RED LIGHT ILLUMINATED. | |||
NOTE: | |||
Step 8: | Step 8: | ||
[22] CHECK generator is loaded by observing | SAT | ||
-II-252-02C/1AMR L2 rise, "N" should be approximately the difference of L1& L2 (UNIT 3 MMG GENERATOR amps, 3-HS-252-02CH positions 1, 2, & 3 are respective to L1, L2 & N). | [22] CHECK generator is loaded by observing UNIT 3 MMG GENERATOR amps, 3-II-252-02C/1AMR L2 rise, "N" should be UNSAT approximately the difference of L1& L2 (UNIT 3 MMG GENERATOR amps, 3-HS-252-02CH positions 1, 2, & 3 are respective to L1, L2 & N). | ||
N/A 8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Cue: L1, L2 , N AMPS INDICATIONS HAVE RISEN and L1-L2 = N. Note: Selector Switch positions are labeled as follows: Position 1 is L1, position 2 is L2 and Position 3 is N. | STEP / STANDARD SAT / UNSAT Standard: | ||
Step 9: | CHECKED amp indicators L1 MINUS L2 approximately equals n. | ||
-HS-280-003/1003 | Cue: L1, L2, N AMPS INDICATIONS HAVE RISEN and L1-L2 = N. | ||
-HS-282-003/1003. | Note: Selector Switch positions are labeled as follows: Position 1 is L1, position 2 is L2 and Position 3 is N. | ||
Step 9: | |||
-HS-280-003/1003 Position Indicating Lamp changed from illuminated RED to illuminated GREEN. | [23] ENSURE OPEN UNIT 3 BKR 1003, 0-HS-280-003/1003 SAT Standard: UNSAT VERIFIED ILLUMINATED GREEN position indicating light above 0- N/A HS-282-003/1003. | ||
Step 10: | Cue: Unit 3 Breaker 1003 0-HS-280-003/1003 Position Indicating Lamp changed from illuminated RED to illuminated GREEN. | ||
BACKUP SOURCE TO BAT BD 1 BKR 1003, 1 | Step 10: | ||
-FUDS-280-001/1003 | [24] On Unit 2 Unit Preferred MMG Set Local Control Panel, ENSURE OPEN the following fused disconnect switches: | ||
-FUDS-280-003/1003 Standard: | * BACKUP SOURCE TO BAT BD 1 BKR 1003, 1-FUDS-280-001/1003 SAT | ||
-FUDS-280-003/1003 in the OPEN POSITION. | * BACKUP SOURCE TO BAT BD 3 BKR 1003, 3-FUDS-280-UNSAT 003/1003 N/A Standard: | ||
At Unit 2 Unit Preferred MMG Set Local Control Panel VERIFIED 1-FUDS-280-001/1003 AND 3-FUDS-280-003/1003 in the OPEN POSITION. | |||
Cue: 1-FUDS-280-001/1003 and 3-FUDS-280-003/1003 are in the OPEN position. | |||
9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Standard: | STEP / STANDARD SAT / UNSAT Step 11: | ||
[25] On Unit 3 Unit Preferred MMG Set Local Control Panel, ENSURE the BACKUP SOURCE TO BAT BD 2 BKR 1003, SAT 2-FUDS-280-002/1003 fused disconnect switch is open: | |||
UNSAT Standard: | |||
N/A On Unit 3 Unit Preferred MMG Set Local Control Panel, VERIFIED 2-FUDS-280-002/1003 in the OPEN position. | |||
Cue: 2-FUDS-280-002/1003 is in the OPEN position. | |||
Step 12: | Step 12: | ||
[26] On Battery Board 2: | [26] On Battery Board 2: | ||
PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH SAT SS-7, 1-HS-252-03/SS-7 in OFF. | |||
PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH SS-7, 1-HS-252-03/SS-7 in OFF. Standard: | UNSAT Standard: | ||
-7, 1-HS-252-03/SS-7 in the OFF position. | N/A SIMULATED PLACING UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 1-HS-252-03/SS-7 in the OFF position. | ||
-7, 1-HS-252-03/SS-7 is in the OFF position. | Cue: UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 1-HS-252-03/SS-7 is in the OFF position. | ||
Step 13: | Step 13: | ||
[27] On Battery Board 2: | [27] On Battery Board 2: | ||
Critical Step DEPRESS UNIT 3 MMG AC MOTOR START, 3-HS-252-02AD to return SAT to Normal AC power from DC drive. | |||
DEPRESS UNIT 3 MMG AC MOTOR START, 3-HS-252-02AD to return to Normal AC power from DC drive. Standard: | UNSAT Standard: | ||
N/A SIMULATED DEPRESSING and RELEASING UNIT 3 MMG AC MOTOR START , 3-HS-252-02AD pushbutton. | |||
Cue: [The AC motor Breaker Position Indicating Lamp changed from illuminated GREEN to illuminated RED. State Another Operator will continue with procedure and this will end the task. | |||
State Another Operator will continue with procedure and this will end the task. | |||
STOP TIME: | STOP TIME: | ||
10 | |||
INITIAL CONDITIONS: | Job Performance Measure (JPM) | ||
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
You are an Operator on Unit 3. The Reactor is in cold shutdown The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1. | INITIAL CONDITIONS: | ||
Maintenance has been completed on the Unit 3 Unit Preferred MMG Set. | You are an Operator on Unit 3. | ||
* The Reactor is in cold shutdown | |||
INITIATING CUES | * The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1. | ||
* Maintenance has been completed on the Unit 3 Unit Preferred MMG Set. | |||
]. NOTE: | INITIATING CUES: | ||
The SM directs you to start up and synchronize the Unit 3 Unit Preferred MMG Set as directed by 0-OI-57C per section 5.5 step 5.5[16]. | |||
NOTE: PERFORMER WILL NEED GGMKA KEY. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
11 | |||
TASK | Job Performance Measure (JPM) | ||
SITE: BFN JPM TITLE: RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: 80A U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: RO: 3.2 SRO: 3.3 201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL K/A No. &STATEMENT: CONTROL SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Rod Drift Alarm RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 1 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
- | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: __80A__ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to respond to a Control Rod Drift In per 2-AOI-85-5. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-85-5, 2-AOI-100-1 VALIDATIONTIME: 18 min PERFORMANCE TIME: | ||
2-AOI-85-5 , 2-AOI-100-1 VALIDATIONTIME: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/10 All Initial issue Incorrect task number; changed to U-085-AB-05: | |||
1 09/01/15 1 Incorrect malfunction numbers; rd07r0231, rd07r2223 & rd07r3031; Corrected 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 280 | |||
* Reset IC 28 or Exam IC if written in above | |||
* Run schedule file:NRC JPM A U2 -Control Rod Drift In | |||
* Verify all triggers and overrides are correct | |||
* Place the simulator in RUN to ensure stable conditions Console | |||
* Start Rod Display on RWM Screen Operator Instructions | |||
- | * Provide Initial Rod Data Sheet -PRLOG | ||
* When prompted by the examiner, INSERT - Event 1 to Drift Control Rod 02-31 into the core | |||
* When prompted by the examiner, INSERT - Event 2 to Drift Control Rod Multiple Control Rods into the core Malfunctions Description Event Severity Delay Initial set rd07r0231 Drifts rod 02-31 into 1 NA 35 sec NA core rd07r2223 Drifts rod 22-23 into 2 NA 10 sec NA core rd07r3031 Drifts rod 30-31 into 2 NA 25 sec NA core rd07r4635 Drifts rod 46-35 into 2 NA 20 sec NA core rd07r2619 Drifts rod 26-19 into 2 NA 30 sec NA core rd07r3027 Drifts rod 30-27 into 2 NA 18 sec NA core rd07r5423 Drifts rod 54-23 into 2 NA 23 sec NA core rd07r2255 Drifts rod 22-55 into 2 NA 28 sec NA core 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): NRC JPM A U2 -Control Rod Drift In 5 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
The Reactor is at 100% power INITIATING CUES | * The Reactor is at 100% power INITIATING CUES: | ||
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | |||
6 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
NOTE | |||
: 1) Problem details of any control rod issues observed during the performance of this surveillance must be recorded on Attachment 3 for further review and possible corrective maintenance. Slow/fast rod movements or settle times should be noted in the remarks section. | |||
: 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1. | : 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1. | ||
CAUTIONS 1) Any mispositioned control rod events will be dispositioned by following the direction contained within 2 | CAUTIONS | ||
-AOI-85-7. 2) If a control rod moves unexpectedly one notch beyond its intended position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. | : 1) Any mispositioned control rod events will be dispositioned by following the direction contained within 2-AOI-85-7. | ||
: 3) At any time CTP is less than or equal to 10%, entry into LCO 3.1.6 may be required. | : 2) If a control rod moves unexpectedly one notch beyond its intended Critical Step position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. SAT | ||
: 3) At any time CTP is less than or equal to 10%, entry into LCO 3.1.6 UNSAT may be required. | |||
N/A 7.3 Exercising a Partially Withdrawn Control Rod | |||
a Partially Withdrawn Control Rod | [1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. | ||
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2 | |||
-XS-85-40. | |||
[2] OBSERVE the following for selected control rod: | [2] OBSERVE the following for selected control rod: | ||
CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. | * CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. | ||
CHECK white light on the Full Core Display is ILLUMINATED. | * CHECK white light on the Full Core Display is ILLUMINATED. | ||
CHECK Rod Out Permit light is ILLUMINATED. | * CHECK Rod Out Permit light is ILLUMINATED. | ||
Standard: | Standard: | ||
Selects a withdrawn control rod Note to Examiner: May select any partially withdrawn control rod in any order 7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 2: | |||
Job Performance Measure (JPM) | [3] INSERT control rod one notch by performing the following: | ||
[3.1] PLACE CRD CONTROL SWITCH, 2 | Critical Step | ||
-HS-85-48 in ROD IN andRELEASE. | [3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN andRELEASE. SAT | ||
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | [3.2] OBSERVE control rod settles into the desired position UNSAT andROD SETTLE light extinguishes. | ||
Standard: | N/A Standard: | ||
Inserts withdrawn control rod one notch Step 3: | |||
[4] WITHDRAW selected control rod one notch by performing the following: Critical Step | |||
[4] WITHDRAW selected control rod one notch by performing the following: | [4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD OUT NOTCHand RELEASE. SAT | ||
[4.1] PLACE CRD CONTROL SWITCH, 2 | [4.2] OBSERVE control rod settles into the desired position and UNSAT ROD SETTLE light extinguishes. | ||
-HS-85-48 in ROD OUT NOTCHand RELEASE. | N/A Standard: | ||
Withdraws withdrawn control rod one notch Step 4: | |||
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | |||
Standard: Withdraws withdrawn control rod one notch | |||
[5] DOCUMENT completion of control rod test as follows: | [5] DOCUMENT completion of control rod test as follows: | ||
[5.1] PERFORMER INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the control rodjust exercised to document proper movement and CRD latching. | [5.1] PERFORMER | ||
[5.2] Concurrent Verifier (CV) | * INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the SAT control rodjust exercised to document proper movement and CRD latching. UNSAT | ||
ENSURE rod inserted and returned to its original position. | [5.2] Concurrent Verifier (CV) N/A | ||
INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised. | * ENSURE rod inserted and returned to its original position. | ||
* INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised. | |||
8 | |||
CONTINUOUS IN. (Otherwise N/A) | Job Performance Measure (JPM) | ||
[3] IF a Control Rod Block occurs during rod insertion due to Rod Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above. (Otherwise N/A) | STEP / STANDARD SAT / UNSAT Standard: | ||
Standard: Responds per 2-AOI-85-5 and inserts control rod 02 | Initials Attachment 1 for exercised control rod and continues to exercise rods. | ||
-31 to full in position as indicated by position 00 indication. | Note to Examiner: | ||
* Perform above actions for @ least two control rods. | |||
-AOI-85-5 , Control Rod Drift In. | * When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #1 for Control Rod 02-31 Drift In Note to Simulator Booth Operator: | ||
* When directed by examiner insert trigger #1 for 02-31 Control Rod Drift In. | |||
Step 5: | |||
Performer recognizes control rod 02-31 drift in and responds per 2-AOI-85-5. | |||
[2] IF a Control Rod is moving from its intended position without Critical Step operator actions, THEN INSERT the Control Rod to position 00 using CONTINUOUS IN. (Otherwise N/A) SAT | |||
[3] IF a Control Rod Block occurs during rod insertion due to Rod UNSAT Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above. | |||
(Otherwise N/A) N/A Standard: | |||
Responds per 2-AOI-85-5 and inserts control rod 02-31 to full in position as indicated by position 00 indication. | |||
CUE: When report to US, state Respond per 2-AOI-85-5, Control Rod Drift In. | |||
Step 6: | Step 6: | ||
[4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod pattern. Standard: Candidate notifies Reactor Engineer to Evaluate Core Thermal limits and Preconditioning Limits for the current Control Rod Pattern | [4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod SAT pattern. | ||
UNSAT Standard: | |||
Candidate notifies Reactor Engineer to Evaluate Core N/A Thermal limits and Preconditioning Limits for the current Control Rod Pattern Cue: Understand Reactor Engineering notified to evaluate Core Thermal andPreconditioning Limits 9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-AOI-100-1. | STEP / STANDARD SAT / UNSAT Step 7: | ||
[6] CHECK Thermal Limits on ICS (RUNMON). | [5] IF another Control Rod Drift occurs before Reactor Engineering completes the evaluation, | ||
Note to NRC Examiner: | * THEN MANUALLY SCRAM Reactor and enter 2-AOI-100-1. SAT | ||
Step [6] performed by Reactor | [6] CHECK Thermal Limits on ICS (RUNMON). UNSAT Note to NRC Examiner: Step [6] performed by Reactor N/A Engineering. | ||
Standard: | Standard: | ||
Reviews step and asks for guidance from US or RE CUE: As Shift Manager, state RE has evaluated Core Thermal and Preconditioning Limits and has determined that the Control Rod Exercise may continue and that any other Control Rod Drift will be considered the first. | |||
Student will continue with Control Rod Exercise. | Student will continue with Control Rod Exercise. | ||
Step 8: | Step 8: | ||
7.3 Exercising a Partially Withdrawn Control Rod | |||
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. Critical Step | |||
[2] OBSERVE the following for selected control rod: SAT | |||
* CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. UNSAT | |||
* CHECK white light on the Full Core Display is ILLUMINATED. | |||
* CHECK Rod Out Permit light is ILLUMINATED. N/A Standard: | |||
Selects a withdrawn control rod 10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 9: | |||
[3] INSERT control rod one notch by performing the following: | |||
Critical Step | |||
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN SAT andRELEASE. | |||
UNSAT | |||
[3.1] PLACE CRD CONTROL SWITCH, 2 | |||
-HS-85-48 in ROD IN andRELEASE. | |||
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | [3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | ||
Standard: | N/A Standard: | ||
Inserts withdrawn control rod one notch Step 10: | |||
[4] WITHDRAW selected control rod one notch by performing the Critical Step following: | |||
[4] WITHDRAW selected control rod one notch by performing the following: | [4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD SAT OUT NOTCHand RELEASE. | ||
[4.1] PLACE CRD CONTROL SWITCH, 2 | UNSAT | ||
-HS-85-48 in ROD OUT NOTCHand RELEASE. | |||
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | [4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | ||
Standard: Withdraws withdrawn control rod one notch Critical Step | N/A Standard: | ||
Withdraws withdrawn control rod one notch Note to Examiner: | |||
When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #2 for Multiple Control Rods Drifting In Step 11: | |||
Multiple Control Rods Drifting In Critical Step Standard: | |||
Recognizes Multiple Control Rods Drift into the Core and Manually SAT Scrams the Reactor per 2-AOI-85-5. | |||
UNSAT | |||
* Depresses both SCRAM Pushbuttons | |||
* Places mode switch in shutdown N/A | |||
* Verifies All Rods in 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 11 continued: | |||
* Performs a Scram Announcement Critical Step o Rx Mode Switch Position: Shutdown o Rod Position: All Full In SAT o Reactor Water Level ____ & Trend ___ | |||
o Reactor Pressure ____ & Trend ___ UNSAT o MSIV Position: OPEN o Rx Power: <5% N/A Termination Criteria: REPEAT BACK SCRAM REPORT THEN STATE, THIS COMPLETES THE JPM. THAT WILL BE ALL FOR NOW, ANOTHER OPERATOR WILL CONTINUE IN 2-AOI-100-1. | |||
STOP TIME: | |||
12 | |||
Job Performance Measure (JPM) | |||
o Reactor Pressure ____ & Trend ___ | |||
o MSIV Position: OPEN o Rx Power: <5 | |||
% | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
The Reactor is at 100% power | * The Reactor is at 100% power INITIATING CUES: | ||
INITIATING CUES | |||
: | |||
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | ||
13 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: | SITE: BFN JPM TITLE: RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: 80A U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: RO: 3.2 SRO: 3.3 201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL CONTROL SYSTEM ; and (b) based on K/A No. &STATEMENT: | ||
those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: | |||
SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): | Rod Drift Alarm RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 1 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | ||
U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
RO: | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL CONTROL SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Rod Drift Alarm RELATED PRA INFORMATION: | Validated by: | ||
Risk Significant SAFETY FUNCTION: | Validator Date Approved by: | ||
1 | Site Training Management Date Approved by: | ||
In-Plant | Site Training Program Owner Date 1 | ||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _80A U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to respond to a Control Rod Drift In per 3-AOI-85-5. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 3-AOI-85-5, 3-AOI-100-1 VALIDATIONTIME: | ||
3-AOI-85-5 , 3-AOI-100-1 | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/10 All Initial issue Incorrect task number; changed to U-085-AB-05: | |||
1 05/11/15 1 Incorrect malfunction numbers; rd07r0231, rd07r2223 & rd07r3031; Corrected 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 280 | |||
* Reset IC 28 or Exam IC if written in above | |||
* Run schedule file: NRC JPM A U3 -Control Rod Drift In | |||
* Verify all triggers and overrides are correct | |||
* Place the simulator in RUN to ensure stable conditions Console Operator | |||
* Start Rod Display on RWM Screen Instructions | |||
* Provide Initial Rod Data Sheet -PRLOG | |||
- | * When prompted by the examiner, INSERT - Event 1 to Drift Control Rod 02-31 into the core | ||
* When prompted by the examiner, INSERT - Event 2 to Drift Control Rod Multiple Control Rods into the core Malfunctions Description Event Severity Delay Initial set rd07r0231 Drifts rod 02-31 into 1 NA 35 sec NA core rd07r2223 Drifts rod 22-23 into 2 NA 10 sec NA core rd07r3031 Drifts rod 30-31 into 2 NA 25 sec NA core rd07r4635 Drifts rod 46-35 into 2 NA 20 sec NA core rd07r2619 Drifts rod 26-19 into 2 NA 30 sec NA core rd07r3027 Drifts rod 30-27 into 2 NA 18 sec NA core rd07r5423 Drifts rod 54-23 into 2 NA 23 sec NA core rd07r2255 Drifts rod 22-55 into 2 NA 28 sec NA core 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): NRC JPM A U3 -Control Rod Drift In 5 | |||
-Control Rod Drift In | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit 3. | |||
You are an Operator on Unit | * The Reactor is at 100% power INITIATING CUES: | ||
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | |||
6 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
NOTE | |||
: 1) Problem details of any control rod issues observed during the performance of this surveillance must be recorded on Attachment 3 for further review and possible corrective maintenance. Slow/fast rod movements or settle times should be noted in the remarks section. | |||
: 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1. | : 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1. | ||
CAUTIONS 3) Any mispositioned control rod events will be dispositioned by following the direction contained within 3-AOI-85-7. | CAUTIONS | ||
: 4) If a control rod moves unexpectedly one notch beyond its intended position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. | : 3) Any mispositioned control rod events will be dispositioned by following the direction contained within 3-AOI-85-7. | ||
: 5) At any time CTP is less than or equal to 10%, entry into LCO 3.1.6 may be required. | : 4) If a control rod moves unexpectedly one notch beyond its intended Critical Step position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. SAT | ||
: 5) At any time CTP is less than or equal to 10%, entry into LCO 3.1.6 UNSAT may be required. | |||
N/A 7.3 Exercising a Partially Withdrawn Control Rod | |||
a Partially Withdrawn Control Rod | |||
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 3-XS-85-40. | [1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 3-XS-85-40. | ||
[2] OBSERVE the following for selected control rod: | [2] OBSERVE the following for selected control rod: | ||
CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. | * CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. | ||
CHECK white light on the Full Core Display is ILLUMINATED. | * CHECK white light on the Full Core Display is ILLUMINATED. | ||
CHECK Rod Out Permit light is ILLUMINATED. | * CHECK Rod Out Permit light is ILLUMINATED. | ||
Standard: | Standard: | ||
Selects a withdrawn control rod Note to Examiner: May select any partially withdrawn control rod in any order 7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 2: | |||
Job Performance Measure (JPM) | [3] INSERT control rod one notch by performing the following: | ||
[3.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD IN andRELEASE. | Critical Step | ||
Standard: | [3.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD IN andRELEASE. SAT | ||
[3.2] OBSERVE control rod settles into the desired position UNSAT andROD SETTLE light extinguishes. | |||
N/A Standard: | |||
[4] WITHDRAW selected control rod one notch by performing the following: | Inserts withdrawn control rod one notch Step 3: | ||
[4.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD OUT NOTCHand RELEASE. | [4] WITHDRAW selected control rod one notch by performing the following: Critical Step | ||
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | [4.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD OUT NOTCHand RELEASE. SAT | ||
Standard: Withdraws withdrawn control rod one notch | [4.2] OBSERVE control rod settles into the desired position and UNSAT ROD SETTLE light extinguishes. | ||
N/A Standard: | |||
Withdraws withdrawn control rod one notch Step 4: | |||
[5] DOCUMENT completion of control rod test as follows: | [5] DOCUMENT completion of control rod test as follows: | ||
[5.1] PERFORMER INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the control rodjust exercised to document proper movement and CRD latching. | [5.1] PERFORMER | ||
[5.2] Concurrent Verifier (CV) | * INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the SAT control rodjust exercised to document proper movement and CRD latching. UNSAT | ||
ENSURE rod inserted and returned to its original position. | [5.2] Concurrent Verifier (CV) N/A | ||
INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised. | * ENSURE rod inserted and returned to its original position. | ||
* INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised. | |||
8 | |||
CONTINUOUS IN. (Otherwise N/A) | Job Performance Measure (JPM) | ||
[3] IF a Control Rod Block occurs during rod insertion due to Rod Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above. (Otherwise N/A) | STEP / STANDARD SAT / UNSAT Standard: | ||
Standard: | Initials Attachment 1 for exercised control rod and continues to exercise rods. | ||
-31 to full in position as indicated by position 00 indication. | Note to Examiner: | ||
* Perform above actions for @ least two control rods. | |||
* When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #1 for Control Rod 02-31 Drift In Note to Simulator Booth Operator: | |||
* When directed by examiner insert trigger #1 for 02-31 Control Rod Drift In. | |||
Step 5: | |||
Performer recognizes control rod 02-31 drift in and responds per 3-AOI-85-5. | |||
[2] IF a Control Rod is moving from its intended position without Critical Step operator actions, THEN INSERT the Control Rod to position 00 using CONTINUOUS IN. (Otherwise N/A) SAT | |||
[3] IF a Control Rod Block occurs during rod insertion due to Rod UNSAT Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above. | |||
(Otherwise N/A) N/A Standard: | |||
Responds per 3-AOI-85-5 and inserts control rod 02-31 to full in position as indicated by position 00 indication. | |||
CUE: When report to US, state Respond per 3-AOI-85-5, Control Rod Drift In. | |||
Step 6: | Step 6: | ||
[4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod pattern. Standard: Candidate notifies Reactor Engineer to Evaluate Core Thermal limits and Preconditioning Limits for the current Control Rod Pattern | [4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod SAT pattern. | ||
UNSAT Standard: | |||
Candidate notifies Reactor Engineer to Evaluate Core N/A Thermal limits and Preconditioning Limits for the current Control Rod Pattern Cue: Understand Reactor Engineering notified to evaluate Core Thermal andPreconditioning Limits 9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-AOI-100-1. | STEP / STANDARD SAT / UNSAT Step 7: | ||
[6] CHECK Thermal Limits on ICS (RUNMON). | [5] IF another Control Rod Drift occurs before Reactor Engineering completes the evaluation, | ||
Note to NRC Examiner: | * THEN MANUALLY SCRAM Reactor and enter 2-AOI-100-1. SAT | ||
Step [6] performed by Reactor | [6] CHECK Thermal Limits on ICS (RUNMON). UNSAT Note to NRC Examiner: Step [6] performed by Reactor N/A Engineering. | ||
Standard: | Standard: | ||
Reviews step and asks for guidance from US or RE CUE: As Shift Manager, state RE has evaluated Core Thermal and Preconditioning Limits and has determined that the Control Rod Exercise may continue and that any other Control Rod Drift will be considered the first. | |||
Student will continue with Control Rod Exercise. | Student will continue with Control Rod Exercise. | ||
Step 8: | Step 8: | ||
7.3 Exercising a Partially Withdrawn Control Rod | |||
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. Critical Step | |||
[2] OBSERVE the following for selected control rod: SAT | |||
* CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. UNSAT | |||
* CHECK white light on the Full Core Display is ILLUMINATED. | |||
* CHECK Rod Out Permit light is ILLUMINATED. N/A Standard: | |||
Selects a withdrawn control rod 10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 9: | |||
[3] INSERT control rod one notch by performing the following: | |||
Critical Step | |||
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN SAT andRELEASE. | |||
UNSAT | |||
[3.1] PLACE CRD CONTROL SWITCH, 2 | |||
-HS-85-48 in ROD IN andRELEASE. | |||
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | [3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes. | ||
Standard: | N/A Standard: | ||
Inserts withdrawn control rod one notch Step 10: | |||
[4] WITHDRAW selected control rod one notch by performing the Critical Step following: | |||
[4] WITHDRAW selected control rod one notch by performing the following: | [4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD SAT OUT NOTCHand RELEASE. | ||
[4.1] PLACE CRD CONTROL SWITCH, 2 | UNSAT | ||
-HS-85-48 in ROD OUT NOTCHand RELEASE. | |||
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | [4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes. | ||
Standard: Withdraws withdrawn control rod one notch | N/A Standard: | ||
Withdraws withdrawn control rod one notch Note to Examiner: | |||
When satisfied with the number of rod manipulations direct Simulator BoothOperator to insert trigger #2 for Multiple Control Rods Drifting In Step 11: | |||
Recognizes Multiple Control Rods Drift into the Core and Manually Scrams the Reactor per 3 | Multiple Control Rods Drifting In Standard: Critical Step Recognizes Multiple Control Rods Drift into the Core and Manually Scrams the Reactor per 3-AOI-85-5. SAT | ||
-AOI-85-5. Depresses both SCRAM Pushbuttons Places mode switch in shutdown Verifies All Rods in | * Depresses both SCRAM Pushbuttons UNSAT | ||
* Places mode switch in shutdown | |||
* Verifies All Rods in N/A 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 11 continued: | |||
Job Performance Measure (JPM) | |||
Critical Step | Critical Step | ||
* Performs a Scram Announcement o Rx Mode Switch Position: Shutdown SAT o Rod Position: All Full In o Reactor Water Level ____ & Trend ___ UNSAT o Reactor Pressure ____ & Trend ___ | |||
o MSIV Position: OPEN N/A o Rx Power: <5% | |||
Termination Criteria: repeat back scram report then state, this completes the JPM. That will be all for now, another operator will continue in 2-AOI-100-1 STOP TIME: | |||
12 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
Job Performance Measure (JPM) | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit | You are an Operator on Unit 3. | ||
* The Reactor is at 100% power INITIATING CUES: | |||
INITIATING CUES | |||
: | |||
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods. | ||
13 | |||
TASK | Job Performance Measure (JPM) | ||
Perform | SITE: BFN JPM TITLE: EHC Auto Cooldown JPM NUMBER: 276 U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-NO-32 Perform Reactor Cooldown TASK NUMBER / TASK TITLE(S): U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: RO: 3.9 SRO: 3.9 239001Main and Reheat Steam System: A4.09 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 4 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | ||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _276 U2 RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to initiate an Auto Cooldown with Turbine Bypass Valves. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-OI-47 VALIDATIONTIME: 4 min PERFORMANCE TIME: | ||
2-OI-47 VALIDATIONTIME: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 06/19/12 All Initial issue 1 07/22/15 All General revision & re-format 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 40 Exam IC 281 | |||
* Reset IC 40 or Exam IC if written in above | |||
* Ensure RFP is in Manual on PDS controller with plant parameters stable. | |||
Console Operator Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): None 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
* The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 2-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6]. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: SAT | |||
[6] VERIFY EHC is in Pressure Control using 2-HS-47-204. UNSAT N/A Standard: | |||
Observes light on for EHC Pressure Control on 2-HS-47-204. | |||
Step 2: | |||
[7] On the EHC Work Station on Panel 9-7: | |||
[7.1] SELECT Main Menu from the toolbar at bottom of the screen. Critical Step | |||
[7.2] SELECT Log In on Display Screen and ENTER OPS SAT for name and OPS for Password. | |||
UNSAT | |||
Job Performance Measure (JPM) | [7.3] SELECT Auto Cooldown from list of function on the screen. N/A Standard: | ||
Observes light on for EHC Pressure Control on 2 | Candidate logs into EHC workstation and selects Auto Cooldown from the list of functions on the screen. | ||
-HS-47-204. | Step 3: | ||
[7] On the EHC Work Station on Panel 9 | [8] On the Auto Cooldown Display Screen CHECK the following are displayed. | ||
-7: | SAT | ||
[7.3] | * Turbine Tripped or All Valves Closed - indicates Reset. | ||
[8] On the Auto Cooldown Display Screen | * Rx Press Ctrl - indicates Reset. UNSAT Standard: N/A | ||
* Candidate checks the Turbine Tripped or All Valves Closed | |||
-indicates Reset. | |||
* Candidate checks Rx Press Ctrl - indicates Reset. | |||
6 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 4: | |||
[9] On the Auto Cooldown Screen SET the desired Final Pressure for cooldown as follows: | |||
[9.1] SELECT the block above the FINAL PRESSURE Critical Step TARGET. | |||
SAT | |||
[9.2] ENTER the desired pressure using the Display Screen or Key Board. | |||
UNSAT | |||
[9.3] WHEN desired Pressure is entered SELECT OK N/A Standard: | |||
Candidate sets the desired final target pressure of 20psig (given in initial conditions). | |||
Step 5: | |||
[10] WHEN Cooldown is ready to commence, THEN | |||
[9.1] SELECT the block above the | |||
[9.3] WHEN desired Pressure is entered SELECT | |||
[10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary) | [10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary) | ||
[10.2] DEPRESS the | Critical Step | ||
[11] WHEN Caution | [10.2] DEPRESS the START button on the Auto Cooldown Display Screen. SAT | ||
Standard: | [11] WHEN Caution Are You Sure You Want to Initiate Auto UNSAT Cooldown? appears N/A SELECT Yes Screen Button to start the cooldown. | ||
Standard: | |||
Candidate depresses START and acknowledges YES to commence auto cooldown. | |||
7 | |||
SAT | Job Performance Measure (JPM) | ||
[13] | STEP / STANDARD SAT / UNSAT Step 6: | ||
[12] CHECK the following: | |||
* EHC PRESSURE SETPOINT, 2-PI-47-162, is lowering. | |||
* EHC AUTO COOLDOWN displays IN PROGRESS SAT Standard: UNSAT Candidate monitors EHC pressure and the auto cooldown is IN N/A PROGRESS. | |||
Cue: The Unit Supervisor directs you to adjust the Final Pressure Target to 100 psig. | |||
Step 7: | |||
[13] IF it is desired to change the Final Pressure Target, THEN On the Auto Cooldown Screen. | |||
[13.1] SELECT the block above the FINAL PRESSURE TARGET Critical Step | |||
[13.2] ENTER the desired pressure using the Display SAT Screen or Key Board. | |||
UNSAT | |||
[13.3] WHEN desired Pressure is entered SELECT OK N/A Standard: | |||
Candidate adjusts FINAL PRESSURE TARGET to 100 psig and recommences the auto cooldown. | |||
Evaluator Cue: Another operator will continue to monitor the cooldown. This completes your task. | |||
STOP TIME: | |||
8 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
* The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
Job Performance Measure (JPM) | INITIATING CUES: | ||
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 2-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6]. | |||
9 | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
INITIATING CUES | |||
2-OI-47, Turbine | |||
-Generator System, Section 8.1.2, starting at step [6]. | |||
TASK | Job Performance Measure (JPM) | ||
Perform | SITE: BFN JPM TITLE: EHC Auto Cooldown JPM NUMBER: 276 U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-NO-32 Perform Reactor Cooldown TASK NUMBER / TASK TITLE(S): U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: RO: 3.9 SRO: 3.9 239001Main and Reheat Steam System: A4.09 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 4 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | ||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _276 U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to initiate an Auto Cooldown with Turbine Bypass Valves. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 3-OI-47 VALIDATIONTIME: | ||
3-OI-47 | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 06/19/12 All Initial issue 1 07/22/15 All General revision & re-format 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 40 Exam IC 281 | |||
* Reset IC 40 or Exam IC if written in above | |||
* Ensure RFP is in Manual on PDS controller with plant parameters stable. | |||
Console Operator Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): None 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 3-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6]. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
[6] VERIFY EHC is in Pressure Control using 3-HS-47-204. SAT UNSAT Standard: | |||
N/A Observes light on for EHC Pressure Control on 3-HS-47-204. | |||
Step 2: | |||
[7] On the EHC Work Station on Panel 9-7: | |||
[7.1] SELECT Main Menu from the toolbar at bottom of the screen. Critical Step | |||
[7.2] SELECT Log In on Display Screen and ENTER OPS SAT for name and OPS for Password. | |||
UNSAT | |||
[7.3] SELECT Auto Cooldown from list of function on the screen. N/A Standard: | |||
Candidate logs into EHC workstation and selects Auto Cooldown from the list of functions on the screen. | |||
Step 3: | |||
[8] On the Auto Cooldown Display Screen CHECK the following are displayed. | |||
SAT | |||
* Turbine Tripped or All Valves Closed - indicates Reset. | |||
* Rx Press Ctrl - indicates Reset. UNSAT Standard: N/A | |||
* Candidate checks the Turbine Tripped or All Valves Closed | |||
-indicates Reset. | |||
* Candidate checks Rx Press Ctrl - indicates Reset. | |||
6 | |||
Job Performance Measure (JPM) | |||
Step 4: | |||
[9] On the Auto Cooldown Screen SET the desired Final Pressure for cooldown as follows: | |||
[9.1] SELECT the block above the FINAL PRESSURE Critical Step TARGET. | |||
SAT | |||
[9.2] ENTER the desired pressure using the Display Screen or Key Board. | |||
Job Performance Measure (JPM) | UNSAT | ||
[9.3] WHEN desired Pressure is entered SELECT OK N/A Standard: | |||
Candidate sets the desired final target pressure of 20psig (given in initial conditions). | |||
Step 5: | |||
[10] WHEN Cooldown is ready to commence, THEN | |||
[9.1] SELECT the block above the | |||
[9.3] WHEN desired Pressure is entered SELECT | |||
[10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary) | [10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary) | ||
[10.2] DEPRESS the | Critical Step | ||
[11] WHEN Caution | [10.2] DEPRESS the START button on the Auto Cooldown Display Screen. SAT | ||
Standard: | [11] WHEN Caution Are You Sure You Want to Initiate Auto UNSAT Cooldown? appears N/A SELECT Yes Screen Button to start the cooldown. | ||
Standard: | |||
Candidate depresses START and acknowledges YES to commence auto cooldown. | |||
7 | |||
SAT | Job Performance Measure (JPM) | ||
[13] | Step 6: | ||
[12] CHECK the following: | |||
* EHC PRESSURE SETPOINT, 3-PI-47-162, is lowering. | |||
* EHC AUTO COOLDOWN displays IN PROGRESS SAT Standard: UNSAT Candidate monitors EHC pressure and the auto cooldown is IN N/A PROGRESS. | |||
Cue: The Unit Supervisor directs you to adjust the Final Pressure Target to 100 psig. | |||
Step 7: | |||
[13] IF it is desired to change the Final Pressure Target, THEN On the Auto Cooldown Screen. | |||
[13.1] SELECT the block above the FINAL PRESSURE TARGET Critical Step | |||
[13.2] ENTER the desired pressure using the Display SAT Screen or Key Board. | |||
UNSAT | |||
[13.3] WHEN desired Pressure is entered SELECT OK N/A Standard: | |||
Candidate adjusts FINAL PRESSURE TARGET to 100 psig and recommences the auto cooldown. | |||
Evaluator Cue: Another operator will continue to monitor the cooldown. This completes your task. | |||
STOP TIME: | |||
8 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves. | |||
Job Performance Measure (JPM) | INITIATING CUES: | ||
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 3-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6]. | |||
9 | |||
Job Performance Measure (JPM) | |||
LOSS OF REFERENCE APRM TO ROD BLOCK SITE: BFN JPM TITLE: | |||
MONITOR JPM NUMBER: 672A U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-085-AL-03 RESPOND TO CONTROL ROD TASK NUMBER / TASK TITLE(S): | |||
WITHDRAWL BLOCK K/A RATINGS: RO: 3.1 SRO: 3.3 215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures K/A No. &STATEMENT: | |||
to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR-3,4,5 RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 7 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Job Performance Measure (JPM) | Site Training Program Owner Date 1 | ||
LOSS OF REFERENCE APRM TO ROD BLOCK MONITOR JPM NUMBER: | |||
672A U2 REVISION: 0 | |||
SRO STA UO NAUO | |||
U-085-AL-03 RESPOND TO CONTROL ROD WITHDRAWL BLOCK K/A RATINGS: | |||
RO: | |||
215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR | |||
-3,4,5 RELATED PRA INFORMATION: | |||
Risk Significant SAFETY FUNCTION: | |||
7 | |||
ALTERNATE PATH (Y/N) | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _672A U2_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to bypass an APRM Channel and clear a Control Rod Block from Rod Block Monitoring System. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-OI-85, 2-OI-92B, 2-ARP-9-5A, 2-SR-3.1.3.5(A) | ||
2-OI-85, 2-OI-92B, 2-ARP-9-5A, 2-SR-3.1.3.5(A) | VALIDATIONTIME: 16 min PERFORMANCE TIME: | ||
VALIDATIONTIME: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 39 Exam IC 282 | |||
* Reset to IC-39 to ~ 30% Reactor Power | |||
* Open Schedule File: NRC JPM C U2 -RBM APRM Fail Console Operator Downscale.sch Instructions | |||
* Open Event File: NRC JPM C U2 -RBM APRM Fail Downscale.evt Malfunctions Description Event Severity Delay Initial set NM07L3233C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-33-C NM07L4025B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-25-B NM07L4033D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-33-D NM07L0817B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-17-B NM07L4017B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-17-B NM07L4041D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-41-D NM07L4049B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-49-B NM07L4057B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-57-B NM07L4817C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-17-C NM07L4825C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-25-C NM07L4833A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-33-A NM07L4841A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-41-A NM07L4849C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-49-C NM07L0825B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-25-B 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
NM07L0833D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-33-D NM07L0841D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-41-D NM07L0849B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-49-B NM07L2409B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-09-B NM07L2417D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-17-D NM07L2425D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-25-D NM07L2433B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-33-B NM07L2449D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-49-D NM07L2457D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-57-D NM07L1617C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-17-C NM07L1625C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-25-C NM07L1633A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-33-A NM07L1641A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-41-A NM07L1649C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-49-C NM07L1657C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-57-C NM07L1609A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-09-A NM07L3209C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-09-C NM07L3217A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-17-A NM07L3225A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-25-A NM07L3249A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-49-A NM07L3257A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-57-A NM07L4009D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-09-D NM07L4809A LPRM AMPLIFIER 15 0 N/A N/A 5 | |||
Schedule File: NRC JPM C U2 | Job Performance Measure (JPM) | ||
-RBM APRM Fail Downscale. | FAILURE 48-09-A NM07L5617D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-17-D NM07L5633B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-33-B NM07L5641B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-41-B NM07L3241C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-41-C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLO4631LGREENT(1) Control Rod 46-31 15 0 N/A N/A GREEN INDICATION Schedule File(s): | ||
Event File: NRC JPM C U2 -RBM APRM Fail Downscale.evt; <TRIGGER id="15" description="APRM Ch 2 Fail Downscale">ZLO4631LGREENT(1) == 0</TRIGGER> | |||
Schedule File: NRC JPM C U2 -RBM APRM Fail Downscale.sch 6 | |||
INITIAL CONDITIONS: | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
* The Reactor is at 30% power | |||
* Startup Sequence Control Rod Movement Data Sheet 2-SR-3.1.3.5(A) completed through group 57. | |||
* No Control Rods are Fast Notching INITIATING CUES: | |||
The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14-31. | |||
7 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
Job Performance Measure (JPM) | |||
Critical Step | Critical Step | ||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40. | |||
SAT UNSAT N/A | SAT Standard: | ||
[2] IF selected control rod has been identified as a | UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | ||
-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2 | Step 2: | ||
-HS | [2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT | ||
Standard: | * THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A) | ||
Determines that step in | N/A Standard: | ||
Determines that step in N/A Step 3: | |||
[3] OBSERVE the following for the selected control rod: | [3] OBSERVE the following for the selected control rod: | ||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED 8 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
[ | STEP / STANDARD SAT / UNSAT Step 4: | ||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 5: | |||
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 6: | |||
Critical Step | Critical Step | ||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
9 | |||
Job Performance Measure (JPM) | |||
-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2 | STEP / STANDARD SAT / UNSAT Step 7: | ||
-HS | [2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT | ||
Standard: | * THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A) | ||
Determines that step in | N/A Standard: | ||
Determines that step in N/A Step 8: | |||
[3] OBSERVE the following for the selected control rod: | [3] OBSERVE the following for the selected control rod: | ||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the correct ROD GROUP when the Rod Worth Minimizer is enforcing Standard: | * White light on the Full Core Display ILLUMINATED SAT | ||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 9: | |||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing 10 | |||
SAT UNSAT | Job Performance Measure (JPM) | ||
[ | STEP / STANDARD SAT / UNSAT Step 10: | ||
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | Critical Step | ||
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 11: | |||
Critical Step | |||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
Step 12: | |||
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT | |||
* THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A) | |||
N/A Standard: | |||
Determines that step in N/A 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 13: | |||
[3] OBSERVE the following for the selected control rod: | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | N/A VERIFIES | ||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the correct ROD GROUP when the Rod Worth Minimizer is enforcing Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 14: | |||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 15: | |||
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | [5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | ||
[6] OBSERVE the control rod settles into the desired position and the ROD SETTLE light extinguishes. | Critical Step | ||
Standard: | [6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | ||
PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | UNSAT Standard: | ||
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 12 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Note to Examiner: This begins the Alternate Path section of JPM Simulator Booth Operator: Insert Event Trigger #1 to fail APRM 2 Downscale. | |||
Step 16: | |||
APRM Sensor/Trip Point: | |||
DOWNSCALE/ | |||
APRM Downscale: <= 5% | |||
OPRM INOP OPRM Inop: Less than 23 operable cells 4 | |||
Sensor Location: | Sensor Location: | ||
Control Room Panel 2-9-14. Probable Cause: | Control Room Panel 2-9-14. | ||
Probable Cause: | |||
A. Unbypassed APRM channel at or below sensor set point. | |||
B. SI or SR in progress. | B. SI or SR in progress. | ||
C. Unit shutdown (Mode 3 or 4). | C. Unit shutdown (Mode 3 or 4). Critical Step D. Failed sensor. | ||
D. Failed sensor. | SAT Automatic Action: UNSAT A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only) | ||
Automatic Action: A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only) | N/A Operator Action: | ||
Operator Action: A. DETERMINE which APRM/OPRM channel is downscale/inop. | A. DETERMINE which APRM/OPRM channel is downscale/inop. | ||
B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 2-OI-92B. | B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 2-OI-92B. | ||
13 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 16(continued) | |||
CONTROL ROD Sensor/Trip Point: | |||
WITHDRAWAL Relays: 3A-K1 Nuclear Instrumentation BLOCK 3A-K2 Refuel Equipment in Use High Level in Scram Discharge 7 Volume Scram Discharge Volume High Water Level Bypass Rx Mode Switch in SHUTDOWN PRNM (ANY APRM OPRM or RBM) | |||
Sensor/Trip Point: | Sensor Location: | ||
Relays: | Panel 2-9-28 Elevation 593' Aux Instr Room Probable Cause: | ||
A. One or more sensors at or above set point. | |||
Panel 2-9-28 Elevation 593' Aux Instr Room Probable Cause: | |||
B. Malfunction of sensor. | B. Malfunction of sensor. | ||
C. Control rod drop accident Automatic Action: Rod withdrawal block Operator Action: | C. Control rod drop accident Automatic Action: | ||
Rod withdrawal block Operator Action: | |||
A. DETERMINE initiating condition from corresponding rod withdrawal block alarm(s) and REFER TO operator action for alarm(s). | |||
Standard: | |||
Reference 2-ARP-9-5A and identifies APRM Ch 2 is down scale and proceeds to bypass APRM Ch 2 per 2-OI-92B CUE: Respond as stated in Alarm Response Instruction and Bypass APRM Ch 2 per 3-OI-92B. | |||
14 | |||
Job Performance Measure (JPM) | |||
APRM/OPRM Channel | STEP / STANDARD SAT / UNSAT Step 17: | ||
NOTES | |||
: 1) Only one APRM/OPRM in each trip system can be bypassed at a time. | |||
: 2) All operations are performed on Panel 2-9-5 unless specifically stated otherwise. | |||
: 3) In order to prevent inadvertent rod withdrawal block or Reactor scram while operating APRM BYPASS selector switch, Verify that the BLUE BYPASSED lights on Panel 9-14 Voters are extinguished prior to selecting any other channel to be bypassed. After bypassing a channel, the applicable BLUE BYPASSED status lights on Panel 9-14 Voters are required to be illuminated prior to testing, operating, or working on that channel. SAT UNSAT 6.1 Bypassing APRM/OPRM Channel N/A CAUTION | |||
[QA/C] SPP-10.4 requires approval of the Plant Manager or his designee prior to any planned operation with APRMs bypassed unless bypassing is specifically allowed within approved procedures. | |||
[ISE-HPS-92-RO1] | |||
[1] REVIEW all precautions and limitations. REFER TO Section 3.0. | [1] REVIEW all precautions and limitations. REFER TO Section 3.0. | ||
Standard: | Standard: | ||
Demonstrates reviewing precautions and limitations section 3.0. | |||
[2] PLACE APRM BYPASS, 2-HS-92-7B/S3, to desired channel to be bypassed. | Step 18: | ||
Standard: | Critical Step | ||
[2] PLACE APRM BYPASS, 2-HS-92-7B/S3, to desired channel to be bypassed. SAT Standard: UNSAT PLACE APRM BYPASS, 2-HS-92-7B/S3, to APRM CH 2 N/A 15 | |||
Job Performance Measure (JPM) | |||
Required During and Following Control Rod Withdrawal (continued) | STEP / STANDARD SAT / UNSAT Step 19: | ||
[6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN | [3] CHECK BLUE BYPASSED lights illuminated on Panel 2-9-14 Voters. SAT Standard: UNSAT Observes BLUE BYPASS light illuminated on Panel 2-9-14 for N/A APRM CH 2. | ||
Step 20: | |||
[4] VERIFY white bypass light on Panel 2-9-5 is illuminated. SAT Standard: UNSAT Observes WHITE BYPASS light illuminated on Panel 2-9-5. N/A Note to Examiner: If needed, cue student to proceed with actions required to continue rod movements. Student may continue at step 21 or 24. | |||
Step 21: | |||
6.6.2 Actions Required During and Following Control Rod Withdrawal (continued) | |||
[6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN SAT PERFORM the following at the Unit Supervisors discretion to UNSAT REINITIALIZE the RBM: | |||
N/A | |||
[6.1] PLACE CRD POWER, 2-HS-85-46 in the OFF position to deselect the Control Rod. | [6.1] PLACE CRD POWER, 2-HS-85-46 in the OFF position to deselect the Control Rod. | ||
Standard: | Standard: | ||
CRD POWER, 2-HS-85-46 in the OFF position. | |||
16 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 22: | |||
SAT | |||
[6.2] PLACE CRD POWER, 2-HS-85-46, in the ON position. | |||
UNSAT Standard: | |||
N/A PLACED CRD POWER, 2-HS-85-46, in the ON position. | |||
Step 23: | |||
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and SAT PERFORM applicable section for Control Rod withdrawal. | |||
UNSAT Standard: | |||
N/A Continues with Control Rod Movement CUE: Proceed with Control Rod Movement. | |||
Step 24: | |||
Critical Step | |||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
17 | |||
Job Performance Measure (JPM) | |||
Job Performance Measure (JPM) | STEP / STANDARD SAT / UNSAT Step 25: | ||
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT | |||
* | * THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A) | ||
N/A Standard: | |||
Determines that step in N/A Step 26: | |||
[3] OBSERVE the following for the selected control rod: | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 27: | |||
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing 18 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 28: | |||
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Termination Criteria: When Control Rod is at position 04, state End of Task STOP TIME: | |||
19 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit | You are an Operator on Unit 2. | ||
* The Reactor is at 30% power | |||
-SR-3.1.3.5(A) completed through group 57. | * Startup Sequence Control Rod Movement Data Sheet 2-SR-3.1.3.5(A) completed through group 57. | ||
INITIATING CUES: | |||
INITIATING CUES | The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14-31. | ||
: | 20 | ||
The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14 | |||
-31. | |||
Job Performance Measure (JPM) | |||
LOSS OF REFERENCE APRM TO ROD BLOCK SITE: BFN JPM TITLE: | |||
MONITOR JPM NUMBER: 672A U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-085-AL-03 RESPOND TO CONTROL ROD TASK NUMBER / TASK TITLE(S): | |||
WITHDRAWL BLOCK K/A RATINGS: RO: 3.1 SRO: 3.3 215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures K/A No. &STATEMENT: | |||
to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR-3,4,5 RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 7 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _672A U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to bypass an APRM Channel and clear a Control Rod Block from Rod Block Monitoring System. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant evolutions precisely. | OF-2 Controlling plant evolutions precisely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 3-OI-85, 3-OI-92B, 3-ARP-9-5A, 3-SR-3.1.3.5(A) | ||
3-OI-85, 3-OI-92B, 3-ARP-9-5A, 3-SR-3.1.3.5(A) | VALIDATIONTIME: | ||
VALIDATIONTIME: | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 04/30/15 All Initial issue 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 39 Exam IC 282 | |||
* Reset IC-39to ~ 30% Reactor Power | |||
* Open Schedule File: NRC JPM C U3 -RBM APRM Fail Console Operator Downscale.sch Instructions | |||
* Open Event File: NRC JPM C U3 -RBM APRM Fail Downscale.evt Malfunctions Description Event Severity Delay Initial set NM07L3233C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-33-C NM07L4025B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-25-B NM07L4033D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-33-D NM07L0817B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-17-B NM07L4017B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-17-B NM07L4041D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-41-D NM07L4049B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-49-B NM07L4057B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-57-B NM07L4817C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-17-C NM07L4825C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-25-C NM07L4833A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-33-A NM07L4841A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-41-A NM07L4849C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-49-C NM07L0825B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-25-B 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
NM07L0833D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-33-D NM07L0841D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-41-D NM07L0849B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-49-B NM07L2409B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-09-B NM07L2417D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-17-D NM07L2425D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-25-D NM07L2433B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-33-B NM07L2449D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-49-D NM07L2457D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-57-D NM07L1617C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-17-C NM07L1625C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-25-C NM07L1633A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-33-A NM07L1641A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-41-A NM07L1649C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-49-C NM07L1657C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-57-C NM07L1609A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-09-A NM07L3209C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-09-C NM07L3217A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-17-A NM07L3225A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-25-A NM07L3249A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-49-A NM07L3257A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-57-A NM07L4009D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-09-D NM07L4809A LPRM AMPLIFIER 15 0 N/A N/A 5 | |||
Schedule File: NRC JPM C U3 | Job Performance Measure (JPM) | ||
-RBM APRM Fail Downscale. | FAILURE 48-09-A NM07L5617D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-17-D NM07L5633B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-33-B NM07L5641B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-41-B NM07L3241C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-41-C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLO4631LGREENT(1) Control Rod 46-31 15 0 N/A N/A GREEN INDICATION Schedule File(s): | ||
Event File: NRC JPM C U3 -RBM APRM Fail Downscale.evt; <TRIGGER id="15" description="APRM Ch 2 Fail Downscale">ZLO4631LGREENT(1) == 0</TRIGGER> | |||
Schedule File: NRC JPM C U3 -RBM APRM Fail Downscale.sch 6 | |||
INITIAL CONDITIONS: | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is at 30% power | |||
* Startup Sequence Control Rod Movement Data Sheet 3-SR-3.1.3.5(A) completed through group 58. | |||
INITIATING CUES: | |||
The US has directed you to raise Reactor Power to 40% per 3-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 59; Control Rod 22-39. | |||
7 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
Job Performance Measure (JPM) | |||
Critical Step | Critical Step | ||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
Step 2: | |||
[2] OBSERVE the following for the selected control rod: | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 3: | |||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing 8 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 4: | |||
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 5: | |||
Critical Step | |||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
Step 6: | |||
[2] OBSERVE the following for the selected control rod: | [2] OBSERVE the following for the selected control rod: | ||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
* White light on the Full Core Display ILLUMINATED SAT | |||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED 9 | |||
SAT UNSAT N/A | Job Performance Measure (JPM) | ||
[ | STEP / STANDARD SAT / UNSAT Step 7: | ||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 8: | |||
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 9: | |||
Critical Step | Critical Step | ||
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40. | |||
SAT Standard: | |||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
10 | |||
SAT UNSAT | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 10: | |||
[2] OBSERVE the following for the selected control rod: | [2] OBSERVE the following for the selected control rod: | ||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
-HS-85-48, in ROD OUT NOTCH, and RELEASE | * White light on the Full Core Display ILLUMINATED SAT | ||
* Rod Out Permit light ILLUMINATED UNSAT Standard: | |||
N/A VERIFIES | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
* White light on the Full Core Display ILLUMINATED | |||
* Rod Out Permit light ILLUMINATED Step 11: | |||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 12: | |||
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | Critical Step | ||
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Note to Examiner: This begins the Alternate Path section of JPM Simulator Booth Operator: Insert Event Trigger #1 to fail APRM 2 Downscale. | |||
Step 13: | |||
APRM Sensor/Trip Point: | |||
DOWNSCALE/ | |||
APRM Downscale: <= 5% | |||
OPRM INOP OPRM Inop: Less than 23 operable cells 4 | |||
This begins the Alternate Path section of JPM Simulator Booth Operator: | |||
Step 13: | |||
APRM Downscale: <=5% | |||
Sensor Location: | Sensor Location: | ||
Control Room Panel 3 14. Probable Cause: | Control Room Panel 3-9-14. | ||
Probable Cause: | |||
A. Unbypassed APRM channel at or below sensor set point. | |||
B. SI or SR in progress. | B. SI or SR in progress. | ||
C. Unit shutdown (Mode 3 or 4). | C. Unit shutdown (Mode 3 or 4). Critical Step D. Failed sensor. | ||
D. Failed sensor. | SAT Automatic Action: UNSAT A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only) | ||
Automatic Action: A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only) | N/A Operator Action: | ||
Operator Action: A. DETERMINE which APRM/OPRM channel is downscale/inop. | A. DETERMINE which APRM/OPRM channel is downscale/inop. | ||
B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 3-OI-92B. | B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 3-OI-92B. | ||
12 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 13(continued) | |||
CONTROL ROD Sensor/Trip Point: | |||
WITHDRAWAL Relays:3A-K1 Nuclear Instrumentation BLOCK 7 3A-K2 Refuel Equipment in Use High Level in Scram Discharge Volume Scram Discharge Volume High Water Level Bypass Rx Mode Switch in SHUTDOWN PRNM (ANY APRM OPRM or RBM) | |||
Sensor Location: | |||
Panel 3-9-28 Elevation 593' Aux Instr Room Probable Cause: | |||
A. One or more sensors at or above set point. | |||
B. Malfunction of sensor. | |||
C. Control rod drop accident Automatic Action: | |||
Rod withdrawal block Operator Action: | |||
A. DETERMINE initiating condition from corresponding rod withdrawalblock alarm(s) and REFER TO operator action for alarm(s). | |||
Standard: | |||
Reference 3-ARP-9-5A and identifies APRM Ch 2 is down scale and proceeds to bypass APRM Ch 2 per 3-OI-92B CUE:Respond as stated in Alarm Response Instruction and Bypass APRM Ch 2 per 3-OI-92B. | |||
13 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 14: | |||
NOTES | |||
: 1) Only one APRM/OPRM in each trip system can be bypassed at a time. | |||
Panel 3-9- | : 2) All operations are performed on Panel 3-9-5 unless specifically stated otherwise. | ||
: 3) In order to prevent inadvertent rod withdrawal block or Reactor scram while operating APRM BYPASS selector switch, Verify that the BLUE BYPASSED lights on Panel 9-14 Voters are extinguished prior to selecting any other channel to be bypassed. After bypassing a channel, the applicable BLUE BYPASSED status lights on Panel 9-14 Voters are required to be illuminated prior to testing, operating, or working on that channel. SAT UNSAT 6.1 Bypassing APRM/OPRM Channel N/A CAUTION | |||
[QA/C] SPP-10.4 requires approval of the Plant Manager or his designee prior to any planned operation with APRMs bypassed unless bypassing is specifically allowed within approved procedures. | |||
[ISE-HPS-92-RO1] | |||
APRM/OPRM Channel | |||
[1] REVIEW all precautions and limitations. REFER TO Section 3.0. | [1] REVIEW all precautions and limitations. REFER TO Section 3.0. | ||
Standard: | Standard: | ||
PLACE APRM BYPASS, 3 | Demonstrates reviewing precautions and limitations section 3.0. | ||
-HS-92-7B/S3, to APRM CH 2 | CUE: If asked per note 2 above, Panel 9-14 Voter BLUE LIGHTS are extinguished. | ||
Step 15: | |||
Critical Step | |||
[2] PLACE APRM BYPASS, 3-HS-92-7B/S3, to desired channel to be bypassed. SAT Standard: UNSAT PLACE APRM BYPASS, 3-HS-92-7B/S3, to APRM CH 2 N/A 14 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 16: | |||
[3] CHECK BLUE BYPASSED lights illuminated on Panel 3-9-14 Voters. SAT Standard: UNSAT Simulates observing BLUE BYPASS light illuminated on Panel 3- N/A 9-14 for APRM CH 2. | |||
Cue: Blue Light is illuminated on Panel 3-9-14 for APRM CH 2. | |||
Step 17: | |||
Job Performance Measure (JPM) | [4] VERIFY white bypass light on Panel 3-9-5 is illuminated. SAT Standard: UNSAT Observes WHITE BYPASS light illuminated on Panel 3-9-5. N/A Note to NRC Examiner: If needed, cue student to proceed with actions required to continue rod movements.Student may continue at step 18 or 21. | ||
Simulates observing BLUE BYPASS light illuminated on Panel 3 14 for APRM CH 2 | Step 18: | ||
6.6.2 Actions Required During and Following Control Rod Withdrawal (continued) | |||
Step | [6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN SAT PERFORM the following at the Unit Supervisors discretion to UNSAT REINITIALIZE the RBM: | ||
[4] VERIFY white bypass light on Panel 3 5 is illuminated. | N/A | ||
[6.1] PLACE CRD POWER, 3-HS-85-46 in the OFF position to deselect the Control Rod. | |||
Standard: | Standard: | ||
CRD POWER, 3-HS-85-46 in the OFF position. | |||
15 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 19: | |||
SAT | |||
[6.2] PLACE CRD POWER, 3-HS-85-46, in the ON position. | |||
UNSAT Standard: | |||
N/A PLACED CRD POWER, 3-HS-85-46, in the ON position. | |||
Step 20: | |||
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and SAT PERFORM applicable section for Control Rod withdrawal. | |||
-HS-85-46, in the ON position. | UNSAT Standard: | ||
Standard: | N/A Continues with Control Rod Movement Cue:If asked,Proceed with Control Rod Movement. | ||
Step 21: | |||
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and PERFORM applicable section for Control Rod withdrawal. | Critical Step | ||
Standard: | [1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40. | ||
Continues with Control Rod Movement | SAT Standard: | ||
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton. | |||
16 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 22: | |||
[2] OBSERVE the following for the selected control rod: | |||
* CRD ROD SELECT pushbutton is brightly ILLUMINATED | |||
CRD ROD SELECT pushbutton is brightly ILLUMINATED White light on the Full Core Display ILLUMINATED Rod Out Permit light ILLUMINATED Standard: | * White light on the Full Core Display ILLUMINATED SAT | ||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the correct ROD GROUP when the Rod Worth Minimizer is enforcing Standard: | * Rod Out Permit light ILLUMINATED UNSAT Standard: | ||
-HS-85-48, in ROD OUT NOTCH, and RELEASE. | N/A VERIFIES | ||
[5] OBSERVE the control rod settles into the desired position and the ROD SETTLE light extinguishes. | * CRD ROD SELECT pushbutton is brightly ILLUMINATED | ||
Standard: | * White light on the Full Core Display ILLUMINATED | ||
PLACED CRD CONTROL SWITCH, 3 48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | * Rod Out Permit light ILLUMINATED Step 23: | ||
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard: | |||
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 24: | |||
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE. | |||
Critical Step | |||
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes. | |||
UNSAT Standard: | |||
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display. | |||
Note to Examiner: Step is repeated to get Control Rod to Position 04 Termination Criteria: When Control Rod is at position 04, state End of Task STOP TIME: | |||
17 | |||
Job Performance Measure (JPM) | |||
Job Performance Measure (JPM) | Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | ||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is at 30% power | |||
** | * Startup Sequence Control Rod Movement Data Sheet 3-SR-3.1.3.5(A) completed through group 58. | ||
INITIATING CUES: | |||
The US has directed you to raise Reactor Power to 40% per 3-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 59; Control Rod 22-39. | |||
18 | |||
Job Performance Measure (JPM) 2-EOI APPENDIX-6E INJECTION SUBSYSTEM LINEUP SITE: BFN JPM TITLE: | |||
CS SYSTEM II JPM NUMBER: 257A U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-35/ Lineup Injection Subsystem-Core TASK NUMBER / TASK TITLE(S): Spray Loop I(II) in Accordance with EOI Appendix 6D(E) | |||
K/A RATINGS: RO: 3.9 SRO: 3.9 209001 Low Pressure Core Spray SystemA4.08 Ability to K/A No. &STATEMENT: manually operate and/or monitor in thecontrol room: Reactor water level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 2 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Job Performance Measure (JPM) | Site Training Program Owner Date 1 | ||
2-EOI APPENDIX | |||
-6E INJECTION SUBSYSTEM LINEUP CS SYSTEM II JPM NUMBER: | |||
SRO STA UO NAUO | |||
-Core Spray Loop I(II) in Accordance with EOI Appendix 6D(E) K/A RATINGS: | |||
RO: | |||
209001 Low Pressure Core Spray SystemA4.08 Ability to manually operate and/or monitor in thecontrol room: Reactor water level RELATED PRA INFORMATION: | |||
Risk Significant SAFETY FUNCTION: | |||
2 | |||
In-Plant | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _257A U2_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to identify and corrects Inboard and Outboard Injection Valve lineup in order to inject water into the RPV with Core Spray System II to recover level Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-EOI APPENDIX-6E VALIDATIONTIME: 8 min PERFORMANCE TIME: | ||
2-EOI APPENDIX-6E VALIDATIONTIME: 8 min | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 12/06/10 All Initial issue 1 04/27/15 All General revision & re-format 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 283 | |||
: 1. Open Schedule File | : 1. Open Schedule File | ||
: 2. Open Event File | : 2. Open Event File | ||
: 3. Reset to IC-28and take out of freeze | : 3. Reset to IC-28and take out of freeze. | ||
: 4. CLOSE 2-FCV-75-51 Console | |||
: 5. OPEN 2-FCV-75-53 Operator | |||
: 6. Man Scram Rx and place MS to SD. | |||
Instructions | |||
: 7. Open 6 ADS Valves. | |||
: 8. Wait until various alarms with Supp Pool Temp High come in to save IC. | |||
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 15 75% 5 Yes INSIDE DRYWELL CS04A CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV II CS02B CS INBOARD 15 N/A N/A Yes INJECTION VALVE AUTO OPENING FAILURE (FCV 53) | |||
RH06A RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV I RH06B RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV II RC01 RCIC TURBINE TRIP 15 N/A N/A Yes SYSTEM FAILURE HP04 HPCI STEAM 15 N/A N/A Yes SUPPLY VALVE AUTO OPENING FAILURE FW01A CONDENSATE 15 N/A 10 Yes PUMP TRIP 2A 4 | |||
Event File(s): JPM 257A U2 Core Spray Alt Inj.evt | Job Performance Measure (JPM) | ||
FW01B CONDENSATE 15 N/A 10 Yes PUMP TRIP 2B FW01C CONDENSATE 15 N/A 10 Yes PUMP TRIP 2C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): JPM 257A U2 Core Spray Alt Inj.sch Event File(s): JPM 257A U2 Core Spray Alt Inj.evt 5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
is complete" and I will acknowledge that your task is complete. | INITIAL CONDITIONS: | ||
You are an Operator on Unit 2. | |||
INITIAL CONDITIONS: | * The Reactor is Shutdown | ||
* RPV Water Level is lowering slowly. | |||
You are an Operator on Unit | * 1-EOI-1 has been entered and followed to RC-L6. | ||
INITIATING CUES: | |||
1-EOI-1 has been entered and followed to RC | The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above | ||
-L6. INITIATING CUES | (-)162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. | ||
6 | |||
-6E, Injection Subsystems Lineup Core Spray System II. | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
Location: Unit 2 Control Room Attachments: 1. NPSH Monitoring | |||
[1] VERIFY OPEN the following valves: | [1] VERIFY OPEN the following valves: | ||
2-FCV-75-30, CORE SPRAY PUMP 2B SUPPR POOL SUCT VLV | SAT | ||
[1] (continued)VERIFY OPEN the following valves: | * 2-FCV-75-30, CORE SPRAY PUMP 2B SUPPR POOL SUCT UNSAT VLV | ||
2-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. | * 2-FCV-75-39, CORE SPRAY PUMP 2D SUPPR POOL SUCT N/A VLV Standard: | ||
Verifies2-FCV-75-30 and 2-FCV-75-39 are open. | |||
Step 2: | |||
[1] (continued)VERIFY OPEN the following valves: Critical Step | |||
* 2-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. SAT UNSAT Standard: | |||
N/A Recognizes 2-FCV-75-51 is closed and 2-FCV-75-53 is open, valve closes 2-FCV-75-53 and Opens 2-FCV-75-51. | |||
Note to Examiner: Student will realignper OPDP-8 Conduct of Ops or OI-75, Core Spray System line up. | |||
7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 3: | |||
[2] VERIFY CLOSED 2-FCV-75-50, CORE SPRAY SYS II SAT TESTVALVE. | |||
UNSAT Standard: | |||
N/A Verifies 2-FCV-75-50 closed Step 4: | |||
Critical Step | |||
Job Performance Measure (JPM) | |||
Standard: | |||
[3] VERIFY CS Pump 2B and/or 2D running. | [3] VERIFY CS Pump 2B and/or 2D running. | ||
Standard: | SAT Standard: | ||
UNSAT Starts Core Pumps 2B and/or 2D N/A (Only starting one pump is Critical, the second pump is optional). | |||
Step 6: | |||
[4] WHEN RPV pressure is below 450 psig, THEN Critical Step THROTTLE2-FCV-75-53, CORE SPRAY SYS II INBDINJECT VALVE, SAT as necessary to control injection at or below4000 gpm per pump. | |||
[4] WHEN RPV pressure is below 450 psig, THEN | UNSAT Standard: | ||
Standard: | N/A Verifies pressure < 450 psig and opens 2-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or | ||
<8000 gpm for 2 pumps). | <8000 gpm for 2 pumps). | ||
Step 7: | |||
CAUTION Continuous operation with inadequate NPSH may result in pump damage or pump inoperability. | |||
SAT | |||
[5] MONITOR Core Spray Pump NPSH using Attachment 1. | [5] MONITOR Core Spray Pump NPSH using Attachment 1. | ||
Standard: Operator comparesCore Spray Pump flow rate with Suppression Pool temperature and Suppression Pool pressure and Determined adequate NPSH. | UNSAT Standard: | ||
Operator comparesCore Spray Pump flow rate with Suppression N/A Pool temperature and Suppression Pool pressure and Determined adequate NPSH. | |||
Termination Criteria: Once rector Water Level is > TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure. | |||
STOP TIME: | STOP TIME: | ||
8 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit 2. | |||
You are an Operator on Unit | * The Reactor is Shutdown | ||
* RPV Water Level is lowering slowly. | |||
1-EOI-1 has been entered and followed to RC | * 1-EOI-1 has been entered and followed to RC-L6. | ||
-L6. | INITIATING CUES: | ||
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above 162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. | |||
INITIATING CUES | 9 | ||
: | |||
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above 162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix | |||
-6E, Injection Subsystems Lineup Core Spray System II. | |||
Job Performance Measure (JPM) 3-EOI APPENDIX-6E INJECTION SUBSYSTEM LINEUP SITE: BFN JPM TITLE: | |||
CS SYSTEM II JPM NUMBER: 257A U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-35/ Lineup Injection Subsystem-Core TASK NUMBER / TASK TITLE(S): Spray Loop I(II) in Accordance with EOI Appendix 6D(E) | |||
K/A RATINGS: RO: 3.9 SRO: 3.9 209001 Low Pressure Core Spray System A4.08 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor water level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 2 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _257A U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to identify and corrects Inboard and Outboard Injection Valve lineup in order to inject water into the RPV with Core Spray System II to recover level Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 3-EOI APPENDIX-6E VALIDATIONTIME: 5 min PERFORMANCE TIME: | ||
3-EOI APPENDIX-6E VALIDATIONTIME: 5 min | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 12/06/10 All Initial issue 1 04/27/15 All General revision & re-format 3 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 283 | |||
: 1. Open Schedule File | : 1. Open Schedule File | ||
: 2. Open Event File | : 2. Open Event File | ||
: 3. Reset to IC | : 3. Reset to IC-28 and take out of freeze. | ||
-28 and take out of freeze. | : 4. CLOSE 2-FCV-75-51 Console | ||
: 4. CLOSE 2-FCV-75-51 5. OPEN 2-FCV-75-53 6. Man Scram Rx and place MS to SD. 7. Open 6 ADS Valves. | : 5. OPEN 2-FCV-75-53 Operator | ||
: 8. Wait until various alarms with Supp Pool Temp High come in to save IC. | : 6. Man Scram Rx and place MS to SD. | ||
Instructions | |||
: 7. Open 6 ADS Valves. | |||
: 8. Wait until various alarms with Supp Pool Temp High come in to save IC. | |||
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 15 75% 5 Yes INSIDE DRYWELL CS04A CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV II CS02B CS INBOARD 15 N/A N/A Yes INJECTION VALVE AUTO OPENING FAILURE (FCV 53) | |||
RH06A RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV I RH06B RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV II RC01 RCIC TURBINE TRIP 15 N/A N/A Yes SYSTEM FAILURE HP04 HPCI STEAM 15 N/A N/A Yes SUPPLY VALVE AUTO OPENING FAILURE FW01A CONDENSATE 15 N/A 10 Yes PUMP TRIP 3A 4 | |||
Event File(s): JPM 257A U3 Core Spray Alt Inj.evt | Job Performance Measure (JPM) | ||
FW01B CONDENSATE 15 N/A 10 Yes PUMP TRIP 3B FW01C CONDENSATE 15 N/A 10 Yes PUMP TRIP 3C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): JPM 257A U3 Core Spray Alt Inj.sch Event File(s): JPM 257A U3 Core Spray Alt Inj.evt 5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are an Operator on Unit 3. | |||
You are an Operator on Unit | * The Reactor is Shutdown | ||
* RPV Water Level is lowering slowly. | |||
1-EOI-1 has been entered and followed to RC | * 1-EOI-1 has been entered and followed to RC-L6. | ||
-L6. INITIATING CUES | INITIATING CUES: | ||
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above | |||
-6E, Injection Subsystems Lineup Core Spray System II. | (-)162 inches (TAF) using Core Spray System II as directed by 3-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. | ||
6 | |||
Job Performance Measure (JPM) | |||
START TIME: | |||
STEP / STANDARD SAT / UNSAT Step 1: | |||
Location: Unit 3 Control Room Attachments: 1. NPSH Monitoring | |||
[1] VERIFY OPEN the following valves: | [1] VERIFY OPEN the following valves: | ||
3-FCV-75-30, CORE SPRAY PUMP 3B SUPPR POOL SUCT VLV | SAT | ||
* 3-FCV-75-30, CORE SPRAY PUMP 3B SUPPR POOL SUCT UNSAT VLV | |||
* 3-FCV-75-39, CORE SPRAY PUMP 3D SUPPR POOL SUCT N/A VLV Standard: | |||
Verifies3-FCV-75-30 and 3-FCV-75-39 are open. | |||
Step 2: | |||
Critical Step | |||
[1] (continued) VERIFY OPEN the following valves: | [1] (continued) VERIFY OPEN the following valves: | ||
3-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. | * 3-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. | ||
SAT UNSAT Standard: | |||
N/A Recognizes 3-FCV-75-51 is closed and 3-FCV-75-53 is open, closes 3-FCV-75-53 and Opens 3-FCV-75-51. | |||
Note to Examiner: Student will realignper OPDP-8 Conduct of Ops or OI-75, Core Spray System line up. | |||
7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 3: | |||
[2] VERIFY CLOSED 3-FCV-75-50, CORE SPRAY SYS II TEST SAT VALVE. | |||
UNSAT Standard: | |||
N/A Verifies 3-FCV-75-50 closed Step 4: | |||
Critical Step | |||
Job Performance Measure (JPM) | |||
-FCV-75-50 closed | |||
[3] VERIFY CS Pump 3B and/or 3D running. | [3] VERIFY CS Pump 3B and/or 3D running. | ||
Standard: | SAT Standard: | ||
UNSAT Starts Core Pumps 3B and/or 3D (Only starting one pump is N/A Critical, the second pump is optional). | |||
Step 6: | |||
[4] WHEN RPV pressure is below 450 psig, THEN Critical Step THROTTLE 3-FCV-75-53, CORE SPRAY SYS II INBDINJECT VALVE, SAT as necessary to control injection at or below4000 gpm per pump. | |||
Standard: | UNSAT Standard: | ||
-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or | N/A Verifies pressure < 450 psig and opens 3-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or | ||
<8000 gpm for 2 pumps). | <8000 gpm for 2 pumps). | ||
Step 7: | |||
CAUTION Continuous operation with inadequate NPSH may result in pump damage or pump inoperability. | |||
SAT | |||
[5] MONITOR Core Spray Pump NPSH using Attachment 1. | [5] MONITOR Core Spray Pump NPSH using Attachment 1. | ||
Standard: Operator compares Core Spray pump flow rate with Suppression Pool temperature and Suppression Pool pressure and Determined adequate NPSH. | UNSAT Standard: | ||
Operator compares Core Spray pump flow rate with Suppression N/A Pool temperature and Suppression Pool pressure and Determined adequate NPSH. | |||
Termination Criteria: Once rector Water Level is > TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure. | |||
TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure. | |||
STOP TIME: | STOP TIME: | ||
8 | |||
is complete" and I will acknowledge that your task is complete. | Job Performance Measure (JPM) | ||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is Shutdown | |||
* RPV Water Level is lowering slowly. | |||
* 1-EOI-1 has been entered and followed to RC-L6. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level using Core Spray System II as directed by 3-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. Directed level band is +2 to +51 inches. | |||
9 | |||
Job Performance Measure (JPM) 2-EOI Appendix-11F Alternate RPV Pressure Control SITE: BFN JPM TITLE: | |||
Systems: RFPT On Minimum Flow JPM NUMBER: 670A U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-58 Lineup Alternate RPV Pressure Control TASK NUMBER / TASK TITLE(S): Systems- RFPT on Minimum Flow IAW EOI Appendix 11F K/A RATINGS: RO: 3.6SRO: 3.6 239001 Main and Reheat Steam System A1.01 Ability to predict and/or monitor changes in parameters associated with K/A No. &STATEMENT: | |||
operating the MAIN ANDREHEAT STEAM SYSTEM controls including: Main steam pressure RELATED PRA INFORMATION: None SAFETY FUNCTION: 3 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _670A U2_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to necessary to place one RFPT in pressure control as directed by 2-EOI Appendix-11F. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | |||
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 2-EOI-APPENDIX-11F VERIFICATION TIME: 12 min PERFORMANCE TIME: | |||
COMMENTS: | |||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
JPM Number: | |||
TASK STANDARD: | |||
Perform operations necessary to necessary to place one RFPT in pressure control as directed by 2 | |||
-EOI Appendix | |||
-11F. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. PRA: NA REFERENCES/PROCEDURES NEEDED: | |||
Procedure: | |||
COMMENTS: | |||
Additional comment sheets attached? | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 284 Malfunctions Description Event Severity Delay Initial set fw15a SPURIOUS RFP 15 N/A 0 N/A BEARING LOW OIL PRESSURE tc03a-j Fail Bypass Valves 1 0% 0 N/A closed ad01e 20 SRV 1-31 stuck open 1 20% 0 N/A 20% | |||
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Initial Setup: | |||
: 1. Reset to IC 28 | : 1. Reset to IC 28 | ||
: 2. Manually Scram RX | : 2. Manually Scram RX | ||
: 3. Trip 2A and 2B RFPT | : 3. Trip 2A and 2B RFPT | ||
: 4. Run Schedule File: NRC JPM E U2 | : 4. Run Schedule File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | ||
-Alt RPV Press Control RFP Min Flow | |||
: 5. Insert Manual Trigger #1 | : 5. Insert Manual Trigger #1 | ||
: 6. After 2A RFPT Speed is <350 RPM Open Event File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | : 6. After 2A RFPT Speed is <350 RPM Open Event File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | ||
Line 4,051: | Line 4,150: | ||
: 8. Freeze simulator and save IC. | : 8. Freeze simulator and save IC. | ||
Schedule Files: | Schedule Files: | ||
: 1. NRC JPM E U2 | : 1. NRC JPM E U2-Alt RPV Press Control RFP Min Flow.sch | ||
-Alt RPV Press Control RFP Min Flow.sch 2. NRC JPM E U2 | : 2. NRC JPM E U2-Alt RPV Press Control RFP Min Flow RFPT Trip.evt 3 | ||
-Alt RPV Press Control RFP Min Flow RFPT Trip.evt | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 2C. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to place 2A RFPT in alternate pressure control, as directed by 2-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / UNSAT Step 1: | |||
[1] IF BOTH of the following exist: | |||
* Emergency RPV Depressurization is required, AND | |||
* Group 1 Isolation Signal exists, THEN SAT EXIT this procedure and ENTER EOI Appendix 11H. UNSAT N/A Standard: | |||
Job Performance Measure (JPM) | |||
Emergency RPV Depressurization is required, AND | |||
Standard: | |||
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | ||
Step 2: | |||
SAT | |||
[2] VERIFY MSIVs open. | |||
UNSAT Standard: | |||
N/A Verifies MSIVs OPEN 6 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 3: | |||
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. SAT Standard: UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 4: | |||
-7 in. Hg. Standard: | |||
Verifies Hotwell Pressure at or below | |||
-7 in. Hg | |||
[4] PLACE RFPTs in service as follows: | [4] PLACE RFPTs in service as follows: | ||
[4.1] VERIFY the following: | [4.1] VERIFY the following: | ||
[4.1.1] At least one condensate pump running. [4.1.2] At least one condensate booster pump running. [4.1.3] Condensate System aligned to supply suction toRFPs. | SAT | ||
Standard: | [4.1.1] At least one condensate pump running. | ||
[4.1.2] At least one condensate booster pump running. | |||
UNSAT | |||
[4.1.3] Condensate System aligned to supply suction toRFPs. | |||
N/A Standard: | |||
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | ||
Step 5: | |||
[4.2] VERIFY Main Oil Pump running for each RFPT to bestarted. | [4.2] VERIFY Main Oil Pump running for each RFPT to bestarted. SAT Standard: UNSAT Verifies main oil pump running for RFPT 2A N/A Step 6: | ||
Standard: | Critical Step | ||
Verifies main oil pump running for RFPT 2A | |||
[4.3] VERIFY CLOSED 2-FCV-3-19, RFP 2ADISCHARGE VALVE. | [4.3] VERIFY CLOSED 2-FCV-3-19, RFP 2ADISCHARGE VALVE. | ||
Standard: | SAT Standard: | ||
VERIFY CLOSED 2-FCV-3-19, RFP 2A DISCHARGE VALVE. | UNSAT VERIFY CLOSED 2-FCV-3-19, RFP 2A DISCHARGE VALVE. | ||
N/A 7 | |||
Standard: | |||
Depresses 2 | Job Performance Measure (JPM) | ||
-HS-46-8A | STEP / STANDARD SAT / UNSAT Step 7: | ||
[4.5] DEPRESS 2-HS-3-124A , RFPT 2A TRIP RESET. | Critical Step | ||
Standard: | [4.4] DEPRESS 2-HS-46-8A RFPT 2A SPEED CONT RAISE/LOWER, and VERIFY amber lightis illuminated. SAT Standard: UNSAT Depresses 2-HS-46-8A N/A Step 8: | ||
Depresses 2 | [4.5] DEPRESS 2-HS-3-124A, RFPT 2A TRIP RESET. Critical Step Standard: SAT Depresses 2-HS-3-124A and verifies the 2-Z1-1-123 LP Stop Valve and UNSAT 2-Z1-127 HP Stop Valve comes OPEN. | ||
-HS-3-124A and verifies the 2 | N/A Step 9: | ||
-Z1-1-123 LP Stop Valve and 2-Z1-127 HP Stop Valve comes OPEN. | Critical Step | ||
[4.6] PLACE 2-HS-46-112A RFPT 2A START/LOCAL ENABLE, in START. SAT Standard: UNSAT Places 2-HS-46-112A in START N/A Note to Examiner: | |||
[4.6] PLACE 2-HS-46-112A RFPT 2A START/LOCAL ENABLE, in START. Standard: | |||
Places 2-HS-46-112A in START | |||
RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10: | RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10: | ||
Critical Step | |||
[4.7] CHECK RFPT 2A speed increases to approximately 600 rpm. | [4.7] CHECK RFPT 2A speed increases to approximately 600 rpm. | ||
Standard: | SAT Standard: | ||
Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 2-EOI-APPENDIX-11F. | UNSAT Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 2-EOI-APPENDIX-11F. N/A CUE: | ||
-EOI-APPENDIX-11F. AO: Reports an oil leak of ~5 gpm on RFPT A bearings. | US: Proceed as directed per 2-EOI-APPENDIX-11F. | ||
Job Performance Measure (JPM) | AO: Reports an oil leak of ~5 gpm on RFPT A bearings. | ||
8 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 11: | |||
[1] IF BOTH of the following exist: | [1] IF BOTH of the following exist: | ||
Emergency RPV Depressurization is required, AND | * Emergency RPV Depressurization is required, AND | ||
* Group 1 Isolation Signal exists, THEN EXIT this procedure and ENTER SAT EOI Appendix 11H. | |||
Standard: | UNSAT Standard: N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | ||
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | Step 12: | ||
[2] VERIFY MSIVs open. SAT Standard: UNSAT Verifies MSIVs OPEN N/A 9 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 13: | |||
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. SAT Standard: UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 14: | |||
-7 in. Hg. Standard: | |||
Verifies Hotwell Pressure at or below | |||
-7 in. Hg | |||
[4] PLACE RFPTs in service as follows: | [4] PLACE RFPTs in service as follows: | ||
[4.1] VERIFY the following: | [4.1] VERIFY the following: | ||
[4.1.1] At least one condensate pump running. [4.1.2] At least one condensate booster pump running. [4.1.3] Condensate System aligned to supply suction toRFPs. | SAT | ||
Standard: | [4.1.1] At least one condensate pump running. | ||
[4.1.2] At least one condensate booster pump running. | |||
UNSAT | |||
[4.1.3] Condensate System aligned to supply suction toRFPs. | |||
N/A Standard: | |||
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | ||
Step 15: | |||
[4.2] VERIFY Main Oil Pump running for each RFPT to be started. Standard: | [4.2] VERIFY Main Oil Pump running for each RFPT to be started. SAT Standard: UNSAT Verifies main oil pump running for RFPT 2B N/A Step 16: | ||
Verifies main oil pump running for RFPT 2B | Critical Step | ||
[4.3] VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE. | [4.3] VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE. | ||
Standard: | SAT Standard: | ||
VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE. | UNSAT VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE. | ||
N/A 10 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 17: | |||
Critical Step | |||
[4.4] DEPRESS 2-HS-46-9A, RFPT 2BSPEED CONT RAISE/LOWER, and VERIFY amber light is illuminated. SAT Standard: UNSAT Depresses 2-HS-46-9A N/A Step 18: | |||
Critical Step | |||
[4.5] DEPRESS 2-HS-3-150A, RFPT 2B TRIP RESET. | |||
SAT Standard: | |||
UNSAT Depresses 2-HS-3-150A and verifies the 2-ZI-1-133 LP Stop Valve and 2-FCV-135 HP Stop Valve comes OPEN. N/A Step 19: | |||
Critical Step | |||
[4.6] PLACE 2-HS-46-138A, RFPT 2B START/LOCAL ENABLE, in START. SAT Standard: UNSAT Places 2-HS-46-138A in START N/A Step 20: | |||
[4.7] CHECK RFPT 2B speed increases to approximately 600 rpm. SAT Standard: UNSAT Verifies RFPT 2B speed increases to approximately 600 rpm N/A 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 21: | |||
[4.8] VERIFY OPEN 2-FCV-3-13, RFP2B MIN FLOW VALVE. SAT Standard: UNSAT Verifies 2-FCV-3-13 OPEN N/A Step 21: | |||
CAUTION RFP discharge pressure is limited to below 1250 psig to avoid system damage. | |||
[4.9] PLACE 2-HS-46-9A, RFPT 2B SPEED CONT RAISE/LOWER in Critical Step RAISE to raise RFPT speed, maintaining discharge pressure less than 1250 psig. SAT Standard: UNSAT Raises RFPT speed using Manual Speed Control Handswitch, N/A maintaining discharge pressure <1250 psig as indicated on 2-PI-3-9A RFPT 2B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable). | |||
STOP TIME END OF TASK 12 | |||
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. | Job Performance Measure (JPM) | ||
-4. Reactor water level control is in automatic on RFPT 2C. | Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | ||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 2C. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to place 2A RFPT in alternate pressure control, as directed by 2-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig. | |||
13 | |||
Job Performance Measure (JPM) 3-EOI Appendix-11F Alternate RPV Pressure Control SITE: BFN JPM TITLE: | |||
: | Systems: RFPT On Minimum Flow JPM 670A JPM NUMBER: REVISION: 0 U3 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-58 Lineup Alternate RPV Pressure Control TASK NUMBER / TASK TITLE(S): Systems- RFPT on Minimum Flow IAW EOI Appendix 11F K/A RATINGS: RO: 3.6 SRO: 3.6 239001 Main and Reheat Steam System A1.01 Ability to predict and/or monitor changes in parameters associated with K/A No. & STATEMENT: | ||
operating the MAIN AND REHEAT STEAM SYSTEM controls including: Main steam pressure RELATED PRA INFORMATION: None SAFETY FUNCTION: 3 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
- | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
OPERATOR: ________________________________ JPM Number: _______ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to necessary to place one RFPT in pressure control as directed by 3-EOI Appendix-11F. | |||
JPM Number: | |||
TASK STANDARD: | |||
Perform operations necessary to necessary to place one RFPT in pressure control as directed by 3 | |||
-EOI Appendix | |||
-11F. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 3-EOI-APPENDIX-11F VERIFICATION TIME: | ||
Procedure: | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
Additional comment sheets attached? | RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | ||
SIGNATURE: ___________________________ DATE: __________ | |||
RESULTS: SATISFACTORY ____ | EXAMINER 2 | ||
UNSATISFACTORY ____ | |||
(Retain entire JPM for records) | |||
SIGNATURE: ___________________________ | |||
DATE: __________ | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 284 Malfunctions Description Event Severity Delay Initial set fw15a SPURIOUS RFP 15 N/A 0 N/A BEARING LOW OIL PRESSURE tc03a-j Fail Bypass Valves 1 0% 0 N/A closed ad01e SRV 1-31 stuck open 1 26% 0 N/A Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set 3 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Initial Setup: | |||
: 1. Reset to IC 28 | : 1. Reset to IC 28 | ||
: 2. Manually Scram RX | : 2. Manually Scram RX | ||
: 3. Trip 2A and 2B RFPT | : 3. Trip 2A and 2B RFPT | ||
: 4. Run Schedule File: NRC JPM E U2 | : 4. Run Schedule File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | ||
-Alt RPV Press Control RFP Min Flow | |||
: 5. Insert Manual Trigger #1 | : 5. Insert Manual Trigger #1 | ||
: 6. After 2A RFPT Speed is <350 RPM Open Event File: NRC JPM E U2 | : 6. After 2A RFPT Speed is <350 RPM Open Event File: NRC JPM E U2-Alt RPV Press Control RFP Min Flow | ||
-Alt RPV Press Control RFP Min Flow | |||
: 7. Verify Auto Trigger #15 is ACTIVE | : 7. Verify Auto Trigger #15 is ACTIVE | ||
: 8. Freeze simulator and save IC. | : 8. Freeze simulator and save IC. | ||
Schedule Files: | Schedule Files: | ||
: 1. NRC JPM E U3 | : 1. NRC JPM E U3-Alt RPV Press Control RFP Min Flow.sch | ||
-Alt RPV Press Control RFP Min Flow.sch 2. NRC JPM E | : 2. NRC JPM E U3-Alt RPV Press Control RFP Min Flow RFPT Trip.evt 4 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/11/15 All Initial issue 5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
(OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | ||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. The Unit 3 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 3C. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to place 3A RFPT in alternate pressure control, as directed by 3-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig. | |||
6 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / UNSAT Step 1: | |||
[1] IF BOTH of the following exist: | |||
* Emergency RPV Depressurization is required, AND | |||
* Group 1 Isolation Signal exists, THEN EXIT this procedure and ENTER SAT EOI Appendix 11H. | |||
UNSAT Standard: N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | |||
Step 2: | |||
Job Performance Measure (JPM) | |||
Emergency RPV Depressurization is required, AND | |||
Standard: | |||
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | |||
[2] VERIFY MSIVs open. | [2] VERIFY MSIVs open. | ||
Standard: | SAT Standard: | ||
Verifies MSIVs OPEN | UNSAT Verifies MSIVs OPEN N/A 7 | ||
Job Performance Measure (JPM) | |||
-7 in. Hg. Standard: | STEP / STANDARD SAT / UNSAT Step 3: | ||
Verifies Hotwell Pressure at or below | [3] VERIFY Hotwell Pressure at or below -7 in. Hg. | ||
-7 in. Hg | SAT Standard: | ||
UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 4: | |||
[4] PLACE RFPTs in service as follows: | [4] PLACE RFPTs in service as follows: | ||
[4.1] VERIFY the following: | [4.1] VERIFY the following: | ||
[4.1.1] At least one condensate pump running. [4.1.2] At least one condensate booster pump running. [4.1.3] Condensate System aligned to supply suction to RFPs. Standard: | [4.1.1] At least one condensate pump running. | ||
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | SAT | ||
[4.1.2] At least one condensate booster pump running. | |||
[4.2] VERIFY Main Oil Pump running for each RFPT to be started. Standard: | [4.1.3] Condensate System aligned to supply suction to RFPs. | ||
Verifies main oil pump running for RFPT | UNSAT Standard: | ||
[4.3] VERIFY CLOSED 3-FCV-3-19, RFP | N/A Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | ||
Standard: | Step 5: | ||
VERIFY CLOSED 3-FCV-3-19, RFP | [4.2] VERIFY Main Oil Pump running for each RFPT to be started. | ||
SAT Standard: | |||
UNSAT Verifies main oil pump running for RFPT 3A N/A Step 6: Critical Step | |||
[4.3] VERIFY CLOSED 3-FCV-3-19, RFP 3A DISCHARGE VALVE. | |||
SAT Standard: | |||
UNSAT VERIFY CLOSED 3-FCV-3-19, RFP 3A DISCHARGE VALVE. | |||
N/A 8 | |||
Job Performance Measure (JPM) | |||
Standard: | STEP / STANDARD SAT / UNSAT Step 7: | ||
Depresses 3-HS-46-8A | [4.4] DEPRESS 3-HS-46-8A, RFPT 3A SPEED CONT RAISE/LOWER, Critical Step and VERIFY amber light is illuminated. | ||
[4.5] DEPRESS 3-HS-3-124A , RFPT | SAT Standard: | ||
Standard: | UNSAT Depresses 3-HS-46-8A N/A Step 8: | ||
Depresses 3 | [4.5] DEPRESS 3-HS-3-124A, RFPT 3A TRIP RESET. Critical Step Standard: SAT Depresses 3-HS-3-124A and resets RFPT Trip and verifies the 3-ZI UNSAT 123 LP Stop Valve and 3-ZI-127 HP Stop Valve comes OPEN. | ||
-HS-3-124A and resets RFPT Trip and verifies the 3 | N/A Step 9: | ||
-ZI | [4.6] PLACE 3-HS-46-112A RFPT 3A START/LOCAL ENABLE, in Critical Step START. | ||
-ZI-127 HP Stop Valve comes OPEN. | SAT Standard: | ||
UNSAT Places 3-HS-46-112A in START N/A Note to Examiner: | |||
[4.6] PLACE 3-HS-46-112A RFPT | RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10: | ||
Places 3-HS-46-112A in START | [4.7] CHECK RFPT 3A speed increases to approximately 600 rpm. | ||
RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10: | SAT Standard: | ||
Standard: | UNSAT Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 3-EOI-APPENDIX-11F. N/A CUE: | ||
Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 3-EOI-APPENDIX-11F. | US: Proceed as directed per 3-EOI-APPENDIX-11F. | ||
AO: Reports an oil leak of ~5 gpm on RFPT A bearings. | |||
9 | |||
Standard: | Job Performance Measure (JPM) | ||
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | STEP / STANDARD SAT / UNSAT Step 11: | ||
[1] IF BOTH of the following exist: | |||
* Emergency RPV Depressurization is required, AND | |||
* Group 1 Isolation Signal exists, THEN EXIT this procedure and ENTER EOI Appendix 11H. SAT UNSAT Standard: | |||
N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve. | |||
Step 12: | |||
[2] VERIFY MSIVs open. | |||
SAT Standard: | |||
UNSAT Verifies MSIVs OPEN N/A 10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 13: | |||
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. | |||
SAT Standard: | |||
-7 in. Hg. Standard: | UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 14: | ||
Verifies Hotwell Pressure at or below | |||
-7 in. Hg | |||
[4] PLACE RFPTs in service as follows: | [4] PLACE RFPTs in service as follows: | ||
[4.1] VERIFY the following: | [4.1] VERIFY the following: | ||
[4.1.1] At least one condensate pump running. [4.1.2] At least one condensate booster pump running. [4.1.3] Condensate System aligned to supply suction to RFPs. Standard: | [4.1.1] At least one condensate pump running. | ||
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | SAT | ||
[4.1.2] At least one condensate booster pump running. | |||
[4.1.3] Condensate System aligned to supply suction to RFPs. | |||
UNSAT Standard: | |||
N/A Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs. | |||
Step 15: | |||
[4.2] VERIFY Main Oil Pump running for each RFPT to be started. | |||
SAT Standard: | |||
UNSAT Verifies main oil pump running for RFPT 3B N/A Step 16: Critical Step | |||
[4.3] VERIFY CLOSED 3-FCV-3-12, RFP 3B DISCHARGE VALVE. | |||
SAT Standard: | |||
UNSAT VERIFY CLOSED 3-FCV-3-12, RFP 3B DISCHARGE VALVE. | |||
N/A 11 | |||
SAT | Job Performance Measure (JPM) | ||
[4. | STEP / STANDARD SAT / UNSAT Step 17: | ||
[4.4] DEPRESS 3-HS-46-9A, RFPT 3B SPEED CONT RAISE/LOWER, Critical Step and VERIFY amber light is illuminated. | |||
[4. | SAT Standard: | ||
Standard: | UNSAT Depresses 3-HS-46-9A N/A Step 18: | ||
[4.5] DEPRESS 3-HS-3-150A, RFPT 3B TRIP RESET. Critical Step Standard: SAT Depresses 3-HS-3-150A and verifies the 3-ZI-1-133 LP Stop Valve and 3- UNSAT FCV-135 HP Stop Valve comes OPEN. | |||
N/A Step 19: | |||
[4.6] PLACE 3-HS-46-138A, RFPT 3B START/LOCAL ENABLE, in Critical Step START. | |||
SAT Standard: | |||
UNSAT Places 3-HS-46-138A in START N/A Step 20: | |||
[4.7] CHECK RFPT 3B speed increases to approximately 600 rpm. | |||
SAT Standard: | |||
UNSAT Verifies RFPT 3B speed increases to approximately 600 rpm N/A 12 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 21: | |||
[4.8] VERIFY OPEN 3-FCV-3-13, RFP 3B MIN FLOW VALVE. Critical Step Standard: SAT Verifies 3-FCV-3-13 OPEN UNSAT N/A Step 21: | |||
CAUTION RFP discharge pressure is limited to below 1250 psig to avoid system damage. | |||
[4.9] PLACE 3-HS-46-9A, RFPT 3B SPEED CONT RAISE/LOWER in Critical Step RAISE to raise RFPT speed, maintaining discharge pressure less than 1250 psig. | |||
SAT Standard: | |||
UNSAT Raises RFPT speed using Manual Speed Control Handswitch, N/A maintaining discharge pressure <1250 psig as indicated on 3-PI-3-9A RFPT 3B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable). | |||
STOP TIME END OF TASK 13 | |||
Standard: | |||
Verifies 3-FCV-3-13 OPEN | |||
[4.9] PLACE 3-HS-46-9A, RFPT | |||
Raises RFPT speed using Manual Speed Control Handswitch, maintaining discharge pressure <1250 psig as indicated on 3-PI-3-9A RFPT 3B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable). | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. The Unit 3 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 3C. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to place 3A RFPT in alternate pressure control, as directed by 3-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig. | |||
14 | |||
Job Performance Measure (JPM) | |||
N2 MAKEUP TO PRIMARY CONTAINMENT WITH SITE: BFN JPM TITLE: | |||
2-EOI-APPENDIX-14A JPM NUMBER: 669 U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-77 Lineup nitrogen Makeup to primary TASK NUMBER / TASK TITLE(S): | |||
Containment IAW EOI-APPENDIX-14A K/A RATINGS: RO: 3.7SRO: 3.8 223001 Primary Containment System and Auxiliaries A2.04; Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT SYSTEM AND AUXILIARIES ; and K/A No. &STATEMENT: (b) based on those predictions, use procedures to correct, control, or mitigate the consequences ofthose abnormal conditions or operations: High containment/drywell hydrogen concentration RELATED PRA INFORMATION: None SAFETY FUNCTION: 5 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _669 U2__ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration. | |||
Job Performance Measure (JPM) | |||
JPM Number: | |||
_669 U2__ | |||
TASK STANDARD: | |||
Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 2-EOI-APPENDIX-14A VERIFICATION TIME: 15 min PERFORMANCE TIME: | ||
Procedure: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 285 | |||
: 1. Open Schedule File | : 1. Open Schedule File | ||
: 2. Open Event File | : 2. Open Event File | ||
: 3. Reset to IC | : 3. Reset to IC-28 and take out of freeze. | ||
-28 and take out of freeze. | |||
: 4. Man Scram Rx and place MS to SD. | : 4. Man Scram Rx and place MS to SD. | ||
: 5. Inhibit ADS & Open 6 ADS Valves. | : 5. Inhibit ADS & Open 6 ADS Valves. | ||
: 6. Fire Trigger 2 | Console | ||
: 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch in BYPASS per EOI APPDX 19 | : 6. Fire Trigger 2 Operator | ||
: 8. Place DW Vent in Service per EOI APPX 12 9. Wait for Group 6 schedule file to time out and alrms to settle | : 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch Instructions in BYPASS per EOI APPDX 19 | ||
: 8. Place DW Vent in Service per EOI APPX 12 | |||
: 9. Wait for Group 6 schedule file to time out and alrms to settle | |||
: 10. Freeze simulator and save IC. | : 10. Freeze simulator and save IC. | ||
Malfunctions Description Event Severity Delay Initial set | Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 2 100 0 Yes INSIDE DRYWELL TH23 FUEL CLADDING 2 100% 0 N/A DAMAGE RC08 RCIC STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE HP04 HPCI STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE CS04A CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV II RD01A CRD PUMP TRIP 1 N/A 0 N/A 2A RD01B CRD PUMP TRIP 1 N/A 0 N/A 2B FW01A CONDENSATE 1 N/A 0 N/A PUMP TRIP 2A FW01B CONDENSATE 1 N/A 0 N/A 3 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
PUMP TRIP 2B FW01C CONDENSATE 1 N/A 0 N/A PUMP TRIP 2C PC08 H2 IN DRYWELL_ 2 29 0 N/A PC09 OXYGEN IN 2 2.8 0 N/A DRYWELL_ | |||
PC10 H2 IN 2 18 0 N/A SUPPRESSION POOL_ | |||
PC11 OXYGEN IN 2 1.5 0 N/A SUPPRESSION POOL_ | |||
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLOXA554C9 DW EQUIP DRAIN 2 N/A N/A ON SUMP LEVEL ABNORMAL Schedule File(s): | |||
* JPM 669 U2 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.sch | |||
* Appendix\App. 8E.sch | |||
* JPM 669 U2 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.evt 4 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/15 All Initial issue 5 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
The Reactor is shutdown. | * The Reactor is shutdown. | ||
2-EOI-APPENDIX-12has been completed | * 2-EOI-APPENDIX-12has been completed | ||
PCIS Group 6 has been overridden per 2 | * 2-EOI-APPENDIX-19 has been completed. | ||
-EOI-APPENDIX- | * PCIS Group 6 has been overridden per 2-EOI-APPENDIX-8E. | ||
INITIATING CUES: | |||
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2-EOI-APPENDIX-14A beginning on step 2. | |||
6 | |||
Job Performance Measure (JPM) | |||
: | START TIME STEP / STANDARD SAT / UNSAT Step 1: | ||
: 2. MONITOR Drywell and Suppression Chamber H2 and O2concentrations on one or more of the following displays(2-EOI Appendix 19): | |||
- | SAT | ||
. | * 2-MON-76-110, H2/O2 ANALYZER (Panel 2-9-55) | ||
UNSAT | |||
* 2-XR-76-110, H2/O2 CONCENTRATION (Panel 2-9-54) | |||
N/A Standard: | |||
Verifies H2 and O2 concentrations Step 2: | |||
: 3. IF ................. Drywell/Suppression Chamber H2 /O2 analyzer is or becomes inoperable, SAT THEN ...........NOTIFY Chemistry Lab to sample Drywell andSuppression Chamber for H2 and O2 using CI-644. | |||
UNSAT Standard: | |||
N/A Verifies Drywell/Suppression Chamber H2 /O2 analyzers are Operable 7 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 3: | |||
4.WHEN ......... Drywell or Suppression Chamber H2 or O2 concentration is increasing,THEN ........... CONTINUE in this procedure. SAT Standard: UNSAT Observes a rise in Drywell H2 Concentration and continues with N/A procedure. | |||
Step 4: | |||
NOTE This procedure assumes that the normal makeup is from N2 Storage Tank B. | |||
SAT | |||
: 5. DISPATCH personnel to N2 Storage Tank B to CHECK 0-PI-76-331, UNSAT N2 TANK B PRESSURE INDICATOR between 160 and 190 psig. | |||
N/A Standard: | |||
Dispatches UO to verifyN2 Storage Tank B Pressure CUE: N2 Storage Tank B Pressure is reading 180 psig Step 5: | |||
: 6. DETERMINE area with highest H2 and/or O2 concentrations and Critical Step INFORM SRO. | |||
SAT Standard: | |||
UNSAT Correctly determines highest concentration is in the drywell and informs US N/A CUE: If asked about 15 minute sample time, state 15 minutes have elapsed 8 | |||
SAT | Job Performance Measure (JPM) | ||
: | STEP / STANDARD SAT / UNSAT Step 6: | ||
Critical Step | |||
: 7. VERIFY PCIS RESET (Panel 2-9-4). | |||
SAT Standard: | |||
UNSAT Verifies PCIS RESET on Panel 2-9-4 N/A Step 7: | |||
Standard: | Critical Step | ||
: | : 8. IF ................. It is desired to makeup N2 to the Suppression Chamber,THEN ...........CONTINUE in this procedure at Step 10. SAT Standard: UNSAT Correctly determine step is not applicable and proceeds to step 9. N/A Step 8: | ||
: 9. CONTROL Drywell H2 and O2 as follows: | |||
Critical Step | |||
: a. OPEN the following valves to admit N2 to Drywell (Panel 2-9-3): | |||
SAT | |||
* 2-FCV-76-18, DRYWELL N2 MAKEUP INBDISOLATION VLV | |||
* 2-FCV-76-17, PRI CTMT N2 MAKEUP OUTBDISOLATION VLV. UNSAT Standard: | |||
N/A OPENS 2-FCV-76-18, DRYWELL N2 MAKEUP INBD ISOLATION VLV & | |||
2-FCV-76-17, PRI CTMT N2 MAKEUP OUTBD ISOLATION VLV Step 9: | |||
: b. SLOWLY ADJUST 2-PC-76-14, DW/SUPPR CHBR N2 MU Critical Step PRESS CONTROL (Panel 2-9-3), to maintain flow > 55 and | |||
<60 scfm on 2-XR-76-14, DW/SUPPR CHBR N2 MAKEUP SAT FLOW/PRESS (Panel 2-9-3), or as directed by SRO if SAMG execution is in progress. | |||
UNSAT Standard: | |||
N/A Achieves a flowrate between 55-60 scfm and monitors Drywell Hydrogen Concentration Lowering 9 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 10: | |||
Job Performance Measure (JPM) | : c. CONTINUEN2 admission to the Drywell UNTIL Drywell H2 andO2 are SAT below desired values. | ||
UNSAT Standard: | |||
N/A Monitors Drywell Hydrogen Concentration Note to Examiner: Once satisfied with N2 Flow established between 55 - 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task. | |||
Standard: | |||
Monitors Drywell Hydrogen Concentration | |||
- 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task. | |||
Pass/ Fail Criteria: Establish N2 Flow> 55 scfm and H2 Concentration on a downward trend. | Pass/ Fail Criteria: Establish N2 Flow> 55 scfm and H2 Concentration on a downward trend. | ||
STOP TIME END OF TASK | STOP TIME END OF TASK 10 | ||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
The Reactor is shutdown. | * The Reactor is shutdown. | ||
2-EOI-APPENDIX-12 has been completed | * 2-EOI-APPENDIX-12 has been completed | ||
PCIS Group 6 has been overridden per 2 | * 2-EOI-APPENDIX-19 has been completed. | ||
-EOI-APPENDIX-8E. | * PCIS Group 6 has been overridden per 2-EOI-APPENDIX-8E. | ||
INITIATING CUES: | |||
INITIATING CUES | The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2-EOI-APPENDIX-14A beginning on step 2. | ||
: | 11 | ||
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2 | |||
-EOI-APPENDIX-14A beginning on step 2 | |||
TASK | Job Performance Measure (JPM) | ||
N2 MAKEUP TO PRIMARY CONTAINMENT WITH 3-SITE: BFN JPM TITLE: | |||
EOI-APPENDIX-14A JPM NUMBER: 670 U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-77 Lineup nitrogen Makeup to primary TASK NUMBER / TASK TITLE(S): | |||
Containment IAW EOI-APPENDIX-14A K/A RATINGS: RO: 3.7SRO: 3.8 223001 Primary Containment System and Auxiliaries A2.04; Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT SYSTEM AND AUXILIARIES ; and K/A No. &STATEMENT: (b) based on those predictions, use procedures to correct, control, or mitigate the consequences ofthose abnormal conditions or operations: High containment/drywell hydrogen concentration RELATED PRA INFORMATION: None SAFETY FUNCTION: 5 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _670 U3_ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration. | |||
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 3-EOI-APPENDIX-14A VERIFICATION TIME: | ||
Procedure: | PERFORMANCE TIME: | ||
COMMENTS: | COMMENTS: | ||
Additional comment sheets attached? YES ___ NO ___ | |||
Additional comment sheets attached? | RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | ||
SIGNATURE: ___________________________ DATE: __________ | |||
RESULTS: SATISFACTORY ____ | EXAMINER 2 | ||
UNSATISFACTORY ____ | |||
(Retain entire JPM for records) | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 285 | |||
: 1. Open Schedule File | : 1. Open Schedule File | ||
: 2. Open Event File | : 2. Open Event File | ||
: 3. Reset to IC | : 3. Reset to IC-28 and take out of freeze. | ||
-28 and take out of freeze. | |||
: 4. Man Scram Rx and place MS to SD. | : 4. Man Scram Rx and place MS to SD. | ||
: 5. Inhibit ADS & Open 6 ADS Valves. | : 5. Inhibit ADS & Open 6 ADS Valves. | ||
: 6. Fire Trigger 2 | Console | ||
: 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch in BYPASS per EOI APPDX 19 | : 6. Fire Trigger 2 Operator | ||
: 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch Instructions in BYPASS per EOI APPDX 19 | |||
: 8. Place DW Vent in Service per EOI APPX 12 | : 8. Place DW Vent in Service per EOI APPX 12 | ||
: 9. Wait for Group 6 schedule file to time out and alrms to settle | : 9. Wait for Group 6 schedule file to time out and alrms to settle | ||
: 10. Freeze simulator and save IC. | : 10. Freeze simulator and save IC. | ||
Malfunctions Description Event Severity Delay Initial set | Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 2 100 0 Yes INSIDE DRYWELL TH23 FUEL CLADDING 2 100% 0 N/A DAMAGE RC08 RCIC STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE HP04 HPCI STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE CS04A CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV II RD01A CRD PUMP TRIP 1 N/A 0 N/A 2A RD01B CRD PUMP TRIP 1 N/A 0 N/A 2B 3 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
FW01C CONDENSATE 1 N/A 0 N/A PUMP TRIP 2C PC08 H2 IN DRYWELL_ 2 29 0 N/A PC09 OXYGEN IN 2 2.8 0 N/A DRYWELL_ | |||
PC10 H2 IN 2 18 0 N/A SUPPRESSION POOL_ | |||
PC11 OXYGEN IN 2 1.5 0 N/A SUPPRESSION POOL_ | |||
Overrides Description Event Severity Delay Initial set ZLOXA554C9 DW EQUIP DRAIN 2 N/A N/A ON SUMP LEVEL ABNORMAL Schedule File(s): | |||
* JPM 669 U3 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.sch | |||
* Appendix\App. 8E.sch | |||
* JPM 669 U3 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.evt 4 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/15 All Initial issue 5 | |||
You are an Operator on Unit | Job Performance Measure (JPM) | ||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
3-EOI-APPENDIX-12 has been completed. | INITIAL CONDITIONS: | ||
3-EOI-APPENDIX-19 has been completed. | You are an Operator on Unit 3. | ||
PCIS Group 6 has been overridden per 3 | * The Reactor is shutdown. | ||
-EOI-APPENDIX- | * 3-EOI-APPENDIX-12 has been completed. | ||
* 3-EOI-APPENDIX-19 has been completed. | |||
* PCIS Group 6 has been overridden per 3-EOI-APPENDIX-8E. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 3-EOI-APPENDIX-14A beginning on step 2. | |||
6 | |||
Job Performance Measure (JPM) | |||
: | START TIME STEP / STANDARD SAT / UNSAT Step 1: | ||
: 3. MONITOR Drywell and Suppression Chamber H2 and O2concentrations on one or more of the following displays(3-EOI Appendix 19): | |||
. | SAT | ||
* 3-MON-76-110, H2/O2 ANALYZER (Panel 3-9-55) | |||
UNSAT | |||
* 3-XR-76-110, H2/O2 CONCENTRATION (Panel 3-9-54) | |||
N/A Standard: | |||
Verifies H2 and O2 concentrations Step 2: | |||
: 3. IF ................. Drywell/Suppression Chamber H2 /O2 analyzer is or becomes inoperable, SAT THEN ...........NOTIFY Chemistry Lab to sample Drywell UNSAT andSuppression Chamber for H2 and O2 using CI-644. | |||
N/A Standard: | |||
Verifies Drywell/Suppression Chamber H2 /O2 analyzers are Operable 7 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 3: | |||
: 4. WHEN ......... Drywell or Suppression Chamber H2 or O2 concentration is increasing,THEN ........... CONTINUE in this procedure. SAT Standard: UNSAT Observes a rise in Drywell H2 Concentration and continues with N/A procedure. | |||
Step 4: | |||
NOTE This procedure assumes that the normal makeup is from N2 Storage Tank B. | |||
SAT | |||
: 5. DISPATCH personnel to N2 Storage Tank B to CHECK 0-PI-76-331, UNSAT N2 TANK B PRESSURE INDICATOR between 160 and 190 psig. | |||
N/A Standard: | |||
Dispatches UO to verifyN2 Storage Tank B Pressure CUE: N2 Storage Tank B Pressure is reading 180 psig Step 5: | |||
: 6. DETERMINE area with highest H2 and/or O2 concentrations and Critical Step INFORM SRO. | |||
SAT Standard: | |||
UNSAT Correctly determines highest concentration is in the drywell and informs US N/A CUE: If asked about 15 minute sample time, state 15 minutes have elapsed 8 | |||
SAT | Job Performance Measure (JPM) | ||
: | STEP / STANDARD SAT / UNSAT Step 6: | ||
Critical Step | |||
: 7. VERIFY PCIS RESET (Panel 3-9-4). | |||
SAT Standard: | |||
UNSAT Verifies PCIS RESET on Panel 3-9-4 N/A Step 7: | |||
Critical Step | |||
: 8. IF ................. It is desired to makeup N2 to the Suppression Chamber,THEN ...........CONTINUE in this procedure at Step 10. SAT Standard: UNSAT Correctly determine step is not applicable and proceeds to step 9. N/A Step 8: | |||
: 9. CONTROL Drywell H2 and O2 as follows: | |||
Critical Step | |||
: a. OPEN the following valves to admit N2 to Drywell (Panel 3-9-3): | |||
SAT | |||
* 3-FCV-76-18, DRYWELL N2 MAKEUP INBDISOLATION VLV | |||
* 3-FCV-76-17, PRI CTMT N2 MAKEUP OUTBDISOLATION VLV. UNSAT Standard: | |||
N/A OPENS 3-FCV-76-18, DRYWELL N2 MAKEUP INBD ISOLATION VLV | |||
&3-FCV-76-17, PRI CTMT N2 MAKEUP OUTBD ISOLATION VLV Step 9: | |||
: b. SLOWLY ADJUST 3-PC-76-14, DW/SUPPR CHBR N2 MUPRESS Critical Step CONTROL (Panel 3-9-3), to maintain flow between 55 and60 scfm on 3-XR-76-14, DW/SUPPR CHBR N2 MAKEUPFLOW/PRESS (Panel 3-SAT 9-3), or as directed by SRO if SAMGexecution is in progress. | |||
UNSAT Standard: | |||
N/A Achieves a flowrate between 55-60 scfm and monitors Drywell Hydrogen Concentration Lowering 9 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 10: | |||
: c. CONTINUE N2 admission to the Drywell UNTIL Drywell H2 and O2 are below desired values. SAT Standard: UNSAT Monitors Drywell Hydrogen Concentration N/A Note to Examiner: Once satisfied with N2 Flow established between 55 - 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task. | |||
: | |||
Standard: | |||
Monitors Drywell Hydrogen Concentration | |||
- 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task. | |||
Pass/ Fail Criteria: Establish N2 Flow > 55 scfm and H2 Concentration on a downward trend. | Pass/ Fail Criteria: Establish N2 Flow > 55 scfm and H2 Concentration on a downward trend. | ||
STOP TIME END OF TASK | STOP TIME END OF TASK 10 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is shutdown. | |||
* 3-EOI-APPENDIX-12 has been completed. | |||
* 3-EOI-APPENDIX-19 has been completed. | |||
* PCIS Group 6 has been overridden per 3-EOI-APPENDIX-8E. | |||
INITIATING CUES: | |||
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 3-EOI-APPENDIX-14A beginning on step 2. | |||
11 | |||
Job Performance Measure (JPM) | |||
Restore Offsite Power to 4KV shutdown board at SITE: BFN JPM TITLE: | |||
PNL 9-23 JPM NUMBER: 631 U2 REVISION: 0 TASK SRO STA UO NAUO APPLICABILITY: | |||
U-082-NO-09 / Restore Offsite Power to 4KV TASK NUMBER / TASK TITLE(S): | |||
shutdown board at PNL 9-23 K/A RATINGS: RO 3.4 SRO 3.4 262001 A.C. Electrical Distribution A4.02 Ability to manually operate and/or monitor in the control room: Synchroscope, K/A STATEMENT: | |||
including understanding of running andincoming voltages RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 6 EVALUATION LOCATION: In -P la n t Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NATIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
: | OPERATOR: ________________________________ JPM Number: 631 U2 RO SRO DATE: _______ | ||
TASK STANDARD: Perform operations necessary to restore offsite power to 4KV SD BD A from 4KV SD BUS 1. | |||
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure 0-OI-82 VERIFICATION TIME: 15 Min PERFORMANCE TIME: | |||
COMMENTS: | |||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
SIMULATOR SETUP IC 28 Exam IC 286 Console 1. Reset to IC 28 and take out of freeze Operator 2. Start A EDG and parallel with offsite Instructions 3. Open 4-kV Shutdown Board A Breaker 1614 Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set 3 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. | |||
I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
No Inclement weather currently exists in the area 8 | * No Inclement weather currently exists in the area | ||
-OI-82, Standby Diesel Generator System. | * 8 hours ago, 4 KV Shutdown Board A was separated from Offsite Power in accordance with 0-OI-82, Standby Diesel Generator System. | ||
INITIATING CUE: | |||
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board A using the normal feeder breaker and remove DG A from parallel operation in accordance with 0-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23. | |||
4 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / | |||
UNSAT Step 1: | |||
0-OI-82 Standby Diesel Generator System Section 8.3 Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23 NOTE The following list of 4-kV shutdown board normal and alternate feeder breakers may be useful when performing this section: | |||
SAT | |||
__UNSAT Shutdown A B C D Board N/A Norm Feed Bkr 1614 1616 1718 1724 Alt Feed Bkr 1716 1714 1624 1618 | |||
[1] VERIFY 4-kV Shutdown Board A is being supplied power by its respective Diesel Generator as the only source of power. | |||
Standard: | |||
Verifies 4-kV Shutdown Board A is being supplied by DG A. | |||
Step 2: | |||
[2] VERIFY the associated 4kV shutdown board auto transfer lockout relay is tripped to MANUAL. | |||
Diesel Handswitch Name Handswitch Panel SAT No. | |||
4KV SD BD A UNSAT A 0-211-3EA 0-9-23-7 AUTO/LOCKOUT RESET N/A Standard: | |||
Verifies 4KV SD BD A AUTO/LOCKOUT RESET, HS-0-211-A, is tripped to manual. | |||
5 | |||
Job Performance Measure (JPM) | |||
- | STEP / STANDARD SAT / | ||
-kV Shutdown | UNSAT Step 3: | ||
- | [3] PLACE the synchroscope switch for the 4-kV shutdown board Critical Step feeder breaker that is to be paralleled with the Diesel Generator in ON. SAT Standard: UNSAT Places Synchroscope switch for 4-kV Shutdown Board A normal N/A feeder breaker 1614 to ON. | ||
Step 4: | |||
[4] VERIFY 4-kV Shutdown Bus 1(2) voltage is between 3950 Volts SAT and 4400 Volts and NOT undergoing abnormal voltage transients. | |||
UNSAT Standard: | |||
N/A Verifies 4-kV Shutdown Bus 1 voltage is between 3950 Volts and 4400 Volts and NOT undergoing abnormal voltage transients. | |||
Step 5: | |||
[5] VERIFY associated incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients. | |||
Shutdown Instrument Name Instrument No. Panel Bd SAT A or B GEN SYNC 0-SI-82-0AB 0-9-23-7 FREQUENCY UNSAT C or D GEN SYNC 0-SI-82-0CD 0-9-23-8 FREQUENCY N/A Standard: | |||
Verifies incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients using GEN SYNC FREQUENCY,0-SI-82-AB. | |||
6 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 6: | |||
CAUTION DO NOT parallel the Diesel Generators with an unstable offsite source or during inclementweather (e.g., lightning, heavy winds). | |||
SAT | |||
[6] IF 4-kV Shutdown Bus 1 (2) is experiencing abnormal voltage or UNSAT frequency conditions, THEN PERFORM the following: | |||
N/A Standard: | |||
STEP N/A Step 7: | |||
CAUTION Only one Unit 1 and 2 Diesel Generator at a time is allowed to be operated in parallel with system. | |||
[6] | |||
Standard: | |||
Critical Step | Critical Step | ||
[7] PULL and PLACE the associated Diesel Generator mode selector switch in PARALLELED WITH SYSTEM. SAT Diesel Handswitch Name Handswitch Panel UNSAT No. | |||
A DG A MODE SELECT 0-HS-82-A/5A 0-9-23-7 N/A Standard: | |||
Pulls DG A MODE SELECT switch 0-HS-82-A/5A and places it in PARALLELED WITH SYSTEM. | |||
7 | |||
Job Performance Measure (JPM) | |||
Diesel | STEP / STANDARD SAT / | ||
UNSAT Step 8: | |||
CAUTION Failure of the PARALLELED WITH SYSTEM light to illuminate in the following step could indicate that the DG is still in SINGLE UNIT operation and result in overload when the DG output breaker is closed. | |||
SAT UNSAT | |||
[8] RELEASE the Diesel Generator mode selector switch and OBSERVE PARALLELED WITH SYSTEM light illuminated. | |||
N/A Standard: | |||
Releases the Diesel Generator A mode selector switch, 0-HS A/5A and observesPARALLELED WITH SYSTEM light is illuminated. | |||
Step 9: | |||
[9] ADJUST Diesel Generator frequency using the associated Diesel Generator governor control switch to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction. | |||
Critical Step Diesel Handswitch Name Handswitch Panel No. SAT A DG A GOVERNOR 0-HS-82-A/3A 0-9-23-7 CONTROL UNSAT Standard: N/A AdjustsDiesel Generator A frequency using Diesel Generator governor control switch, 3-HS-82-A/3A, (in lower direction) to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction. | |||
8 | |||
SAT UNSAT N/A Step | Job Performance Measure (JPM) | ||
[ | STEP / STANDARD SAT / | ||
-kV shutdown board feeder breaker that | UNSAT Step 10: | ||
[10] USE the associated Diesel Generator voltage regulator control switch to match Diesel Generator and System voltages. | |||
Diesel Instrument Name Inst No. Panel DG A VOLT REGULATOR 0-HS-82-A/2A SAT CONT A GEN SYNC REF VOLTAGE 0-EI-82-AB 0-9-23-7 UNSAT SYSTEM SYNC REF 0-EI-211-0AB VOLTAGE N/A Standard: | |||
[ | Matches DG A voltage with system voltage using DG A VOLT REGULATOR CONT switch 0-HS-82-A/2A. | ||
Step 11: | |||
[11] WHEN the synchroscope needle is approximately 2 minutes on Critical Step the right hand side of the 12 o'clock position, THEN CLOSE the 4-kV shutdown board feeder breaker that is to be SAT paralleled with the Diesel Generator. | |||
UNSAT Standard: | |||
N/A Closesthe 4-kV shutdown board feeder breaker 1614 when the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position. | |||
Step 12: | |||
[12] PLACE the synchroscope switch for the 4-kV shutdown board SAT feeder breaker that was paralleled with the Diesel Generator in OFF. | |||
UNSAT Standard: | |||
N/A Places the synchroscope switch for BKR 1614 in OFF. | |||
9 | |||
toINCREASE kW and kVAR load, in increments of 100kWevery 15 minutes. | Job Performance Measure (JPM) | ||
Diesel Handswitch Name | STEP / STANDARD SAT / | ||
[13.3] STEP N/A [13.4] WHEN smoke becomes relatively clear, | UNSAT Step 13: | ||
NOTE If diesel operates greater than 4 hours at less than 50% load, the diesel should be loaded to full load for at least 30 minutes prior to engine shutdown. This will allow the engine to clean out any oil accumulations from the exhaust manifolds. | |||
[13] IF DG has been operating at a low-load condition (50%) for an extended period of time (4 hours) THEN PERFORM the following (Otherwise N/A): | |||
[13.1] USE the associated Diesel Generator's governor controlswitch and voltage regulator control switch toINCREASE kW and kVAR load, in increments of Critical Step 100kWevery 15 minutes. | |||
SAT Diesel Handswitch Name Hands Panel witch UNSAT No. | |||
DG A GOVERNOR CONTROL 0-HS-N/A 82-A/3A A 0-9-23-7 DG A VOLT REGULATOR 0-HS-CONTROL 82-A/2A | |||
[13.2] OBSERVE the exhaust stack smoke concentration from outside the DG room after each incremental increase. | |||
[13.3] STEP N/A | |||
[13.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible. | |||
[13.5] MAINTAIN 100% load for a minimum of 30 minutes. | [13.5] MAINTAIN 100% load for a minimum of 30 minutes. | ||
Standard: | Standard: | ||
Loads DG to 2600 kW and 1850 kVAR by using 0-HS-82-A/3A and 0-HS-82-A/2A handswitches. | |||
CUE: After first 100 kW load adjustment state 15 minutes have elapsed and no observable black smoke from exhaust stack for time compression and continue to full load. | |||
10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
Panel | UNSAT Step 14: | ||
Step | NOTE Lagging VARs should be maintained when adjusting kW load (rising or lowering). This may require kW load adjustment to be stopped periodically to allow for adjusting kVAR load. Once desired kW load is achieved, Illustration 1 should be referred to for determination of kVAR loading required to obtain a power factor (pf) of 0.8 lagging. Diesel generator kVAR load should then be adjusted to obtain a 0.8 pf lagging. IF system conditions will NOT permit the kVAR loading required to obtain a 0.8 pf lagging, kVAR load should be adjusted to the maximum kVAR lagging the system will allow. | ||
[15] | SAT UNSAT | ||
[14] USE the associated Diesel Generator's governor control switch and voltage regulator control switch to obtain desired kW and N/A kVAR load. | |||
Diesel Handswitch Name Handswitch No. Panel DG A GOVERNOR CONTROL 0-HS-82-A/3A A 0-9-23-7 DG A VOLT REGULATOR CONT 0-HS-82-A/2A Standard: | |||
Obtains desired kW and kVAR load using DG A Governor Control switch, 0-HS-82-A/3A and DG Volt Regulator Cont switch, 0-HS-82-A/2A. | |||
CUE: state 30 minutes have elapsed continue with procedure. | |||
Step 15: | |||
[15] MONITOR the offsite source that is paralleled with the Diesel Generator. SAT | |||
[16] IF abnormal voltage or frequency transients are experienced, UNSAT THEN N/A Standard: | |||
Step is N/A 11 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
UNSAT Step 16: | |||
[17] WHEN Parallel with System operation is no longer desired, THEN UNLOAD the Diesel Generator as follows: | |||
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVARlimit may result in a reverse power trip of the Diesel Generator output breaker. | CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVARlimit may result in a reverse power trip of the Diesel Generator output breaker. | ||
[17.1] | [17.1] USE the associated Diesel Generator's governor control Critical Step switch and voltage regulator control switch to reduce generator load to approximately 300 kW and SAT 250 kVAR: | ||
UNSAT Diesel Instrument Name Inst No. Panel N/A DG A GOVERNOR CONTROL 0-HS-82-A/3A DG A VOLTAGE 0-HS-82-A/2A A REGULATOR CONTROL 0-9-23-7 DG A KILOWATTS 0-JI-82-A/A DG A KILOVARS 0-VAR-82-A/A Standard: | |||
Unloads the DG to approximately 300 KW and 250 kVAR. | |||
Step 17 | |||
Panel A DG A BKR 1818 0-HS-211-A/ | [17.2] PLACE the associated Diesel Generator breaker control Critical Step switch in TRIP SAT Diesel Handswitch Name Handswitch No. Panel A DG A BKR 1818 0-HS-211-A/22A 0-9-23-7 UNSAT N/A Standard: | ||
Trips Diesel Generator breaker 1818. | |||
12 | |||
. | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 18: | |||
[17.3] PULL and PLACE the associated Diesel Generator mode Critical Step selector switch in SINGLE UNIT. | |||
SAT Diesel Handswitch Name Handswitch No. Panel A DG A MODE SELECT 0-HS-211-A/5A 0-9-23-7 UNSAT N/A Standard: | |||
Pulls and places 0-HS-211-A/5A to Single Unit. | |||
Step 19: | |||
[17.4] RELEASE the Diesel Generator mode selector switch and SAT OBSERVE the SINGLE UNIT light illuminated. | |||
UNSAT Standard: | |||
N/A Verifies Single Unit light illuminated. | |||
CUE: ANOTHER OPERATOR WILL CONTINUE FROM HERE STOP TIME END OF TASK 13 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | You are an Operator on Unit 2. | ||
No Inclement weather currently exists in the area 8 | * No Inclement weather currently exists in the area | ||
-OI-82, Standby Diesel Generator System. | * 8 hours ago, 4 KV Shutdown Board A was separated from Offsite Power in accordance with 0-OI-82, Standby Diesel Generator System. | ||
INITIATING CUE: | |||
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board A using the normal feeder breaker and remove DG A from parallel operation in accordance with 0-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23. | |||
14 | |||
Job Performance Measure (JPM) | |||
Restore Offsite Power to 4KV shutdown board at PNL 9-SITE: BFN JPM TITLE: | |||
23 U-3 JPM NUMBER: 631 REVISION: 0 TASK SRO STA UO NAUO APPLICABILITY: | |||
U-082-NO-09 / Restore Offsite Power to 4KV TASK NUMBER / TASK TITLE(S): | |||
shutdown board at PNL 9-23 K/A RATINGS: RO 3.4 SRO 3.4 262001 A.C. Electrical Distribution A4.02 Ability to manually operate and/or monitor in the control K/A STATEMENT: room: Synchroscope, including understanding of running and incoming voltages RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 6 EVALUATION LOCATION: In -P la n t Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
-OI-82 | OPERATOR: ________________________________ JPM Number: 631 RO SRO DATE: _______ | ||
TASK STANDARD: Perform operations necessary to restore offsite power to 4KV SD BD EC. | |||
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure 3-OI-82 VERIFICATION TIME: 15 Min PERFORMANCE TIME: | |||
COMMENTS: | |||
Additional comment sheets attached? YES ___ NO ___ | |||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
SIMULATOR SETUP IC 28 Exam IC 286 | |||
: 1. Reset to IC 28 and take out of freeze Console | |||
: 2. Start C EDG and parallel with offsite Operator | |||
: 3. Open 4-kV Shutdown Board 3EC Breaker 1338 Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Batch / Pref File(s): | |||
3 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. | |||
I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* No Inclement weather currently exists in the area | |||
* 8 hours ago, 4 KV Shutdown Board 3EC was separated from Offsite Power in accordance with 3-OI-82, Standby Diesel Generator System. | |||
INITIATING CUE: | |||
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board 3EC using the normal feeder breaker and remove DG 3C from parallel operation in accordance with 3-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23. | |||
4 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / | |||
UNSAT Step 1: | |||
3-OI-82 Standby Diesel Generator System Section 8.3 Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23 NOTE The following list of 4-kV shutdown board normal and alternate feeder breakers may be useful when performing this section: | |||
SAT UNSAT Shutdown 3EA 3EB 3EC 3ED Board N/A Norm Feed Bkr 1334 1336 1338 1342 Alt Feed Bkr 1726 1728 1626 1628 | |||
[1] VERIFY 4-kV Shutdown Board 3EC is being supplied power by its respective Diesel Generator as the only source of power. | |||
Standard: | |||
Verifies 4-kV Shutdown Board EC is being supplied by DG C Step 2: | |||
[2] VERIFY the associated 4kV shutdown board auto transfer lockout relay is tripped to MANUAL. | |||
SAT Diesel Handswitch Name Handswitch No. Panel 4KV SD BD 3EC 3-43-211- UNSAT 3C 3-9-23 AUTO/LOCKOUT RESET 3EC N/A Standard: | |||
Verifies 4KV SD BD 3EC AUTO/LOCKOUT RESET, 3-43-211-3EC, is tripped to manual. | |||
5 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
UNSAT Step 3: | |||
[3] PLACE the synchroscope switch for the 4-kV shutdown board Critical Step feeder breaker that is to be paralleled with the Diesel Generator in ON. SAT Standard: UNSAT Places Synchroscope switch for 4-kV Shutdown Board EC normal N/A feeder breaker 1338 to ON Step 4: | |||
[4] CHECK the applicable 4-kV unit board (4-kV bus tie board) | |||
SAT voltage is between 3950 VOLTS and 4400 VOLTS and NOT undergoing abnormal voltage transients. | |||
UNSAT Standard: | |||
N/A Verifies 4-kV Unit Board voltage is between 3950 Volts and 4400 Volts and NOT undergoing abnormal voltage transients. | |||
Step 5: | |||
[5] VERIFY associated incoming frequency is between 59 HERTZ and 61 HERTZ and NOT undergoing abnormal frequency transients. | |||
Shutdown Instrument Name Instrument No. Panel SAT Bd 3EA or GEN SYNC 3-SI-82-3AB 3-9-23 UNSAT 3EB FREQUENCY 3EC or GEN SYNC 3-SI-82-3CD 3-9-23 N/A 3ED FREQUENCY Standard: | |||
Verifies incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients using GEN SYNC FREQUENCY, 3-SI-82-CD . | |||
6 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
UNSAT Step 6: | |||
CAUTION DO NOT parallel the Diesel Generators with an unstable offsite source or during inclement weather (e.g., lightning, heavy winds). SAT UNSAT | |||
[6] IF 4-kV unit board (4-kV bus tie board) is experiencing abnormal voltage or frequency conditions, THEN PERFORM the following: N/A Standard: | |||
N/A Step 7: | |||
CAUTION Only one Unit 1 and 2 Diesel Generator at a time is allowed to be operated in parallel with system. | |||
Critical Step | |||
[7] PULL and PLACE the associated Diesel Generator mode SAT selector switch in PARALLELED WITH SYSTEM. | |||
UNSAT Diesel Handswitch Name Handswitch Panel No. | |||
N/A 3C DG 3C MODE SELECT 3-HS-82-3C/5A 3-9-23 Standard: | |||
Pulls DG 3C MODE SELECT switch 3-HS-82-3C/5A and places it in PARALLELED WITH SYSTEM 7 | |||
Job Performance Measure (JPM) | |||
: | STEP / STANDARD SAT / | ||
: | UNSAT Step 8: | ||
: 3 | CAUTION Failure of the PARALLELED WITH SYSTEM light to illuminate in the following step could indicate that the DG is still in SINGLE UNIT operation and result in overload when the DG output breaker is closed. SAT UNSAT | ||
[8] RELEASE the Diesel Generator mode selector switch and OBSERVE PARALLELED WITH SYSTEM light illuminated. N/A Standard: | |||
Releases the Diesel Generator 3C mode selector switch, 3-HS-82-3C/5C and observes PARALLELED WITH SYSTEM light is illuminated. | |||
Step 9: | |||
[9] ADJUST Diesel Generator frequency using the associated Diesel Generator governor control switch to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction. | |||
Critical Step Diesel Handswitch Name Handswitch Panel No. SAT 3C DG 3C GOVERNOR 3-HS-82-3C/3A 3-9-23 CONTROL UNSAT Standard: N/A Adjusts Diesel Generator 3C frequency using Diesel Generator governor control switch, 3-HS-82-3C/3A (in lower direction) to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction. | |||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 10: | |||
[10] USE the associated Diesel Generator voltage regulator control switch to match Diesel Generator and System voltages. | |||
Dies Instrument Name Inst No. Panel el SAT DG 3C VOLT REGULATOR 3-HS CONT 3C/2A UNSAT 3C GEN SYNC REF VOLTAGE 3-EI-82-3CD 3-9-23 SYSTEM SYNC REF 3-EI-211-VOLTAGE 3ECB/B N/A Standard: | |||
Matches DG C voltage with system voltage using DG 3C VOLT REGULATOR CONT switch 3-HS-82-3C/2A Step 11: | |||
[11] WHEN the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position, THEN Critical Step CLOSE the 4-kV shutdown board feeder breaker that is to be SAT paralleled with the Diesel Generator. | |||
UNSAT Standard: | |||
N/A Closes the 4-kV shutdown board normal feeder breaker 1338 when the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position. | |||
Step 12: | |||
[12] PLACE the synchroscope switch for the 4-kV shutdown board SAT feeder breaker that was paralleled with the Diesel Generator in OFF. UNSAT Standard: N/A Places the synchroscope switch for BKR 1338 in OFF 9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 13: | |||
[13] IF the normal feeder breaker is supplying the 4-kV shutdown board, THEN RESET the associated 4kV shutdown board auto transfer lockout Critical Step relay. | |||
SAT Diesel Handswitch Name Handswitch Panel No. | |||
UNSAT 3C 4KV SD BD 3EC 3-43-211-3EC 3-9-23 AUTO/LOCKOUT N/A RESET Standard: | |||
Resets 4KV SD BD 3EC Auto Transfer Lockout Relay Step 14: | |||
NOTE If diesel operates greater than 4 hours at less than 50% load, the diesel should be loaded to full load for at least 30 minutes prior to engine shutdown. This will allow the engine to clean out any oil accumulations from the exhaust manifolds. | |||
[14] IF DG has been operating at a low-load condition (50%) for an extended period of time (4 hours) THEN PERFORM the following (Otherwise N/A): Critical Step | |||
[14.1] USE the associated Diesel Generators governor control SAT switch and voltage regulator control switch to INCREASE kW and kVAR load, in increments of 100kW every 15 UNSAT minutes. | |||
N/A Diesel Handswitch Name Hands Panel witch No. | |||
DG 3C GOVERNOR CONTROL 3-HS-82-3C/3A 3C 3-9-23 DG 3C VOLT REGULATOR 3-HS-CONTROL 82-3C/2A 10 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / | |||
UNSAT Step 14 continued: | |||
[14.2] OBSERVE the exhaust stack smoke concentration from outside the DG room after each incremental increase. | |||
[14.3] STEP N/A | |||
[14.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible. | |||
[14.3] STEP N/A [14.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible. | |||
[14.5] MAINTAIN 100% load for a minimum of 30 minutes. | [14.5] MAINTAIN 100% load for a minimum of 30 minutes. | ||
Standard: | Standard: | ||
-HS-82-A/3A and 0-HS-82-A/2A handswitches. | Loads DG to 2600 kW and 1850 kVAR by using 0-HS-82-A/3A and 0-HS-82-A/2A handswitches. | ||
CUE: After first 100 kW load adjustment state | CUE: After first 100 kW load adjustment state 15 minutes have elapsed and no observable black smoke from exhaust stack for time compression and continue to full load. | ||
Step 15: | |||
[15] | NOTE VARs lagging should be maintained when adjusting kW load (rising or lowering). This may require kW load adjustment to be stopped periodically to allow for adjusting kVAR load. Once desired kW load is achieved, Illustration 1 should be referred to for determination of kVAR loading required to obtain a power factor (pf) of 0.8 lagging. Diesel generator kVAR load should then be adjusted to obtain a 0.8 pf lagging. IF system conditions will NOT permit the kVAR loading required to obtain a 0.8 pf lagging, kVAR load should be adjusted to SAT the maximum kVAR lagging the system will allow. | ||
Diesel Handswitch Name Handswitch No. | UNSAT | ||
Panel | [15] USE the associated Diesel Generator's governor control switch N/A and voltage regulator control switch to obtain desired kW and kVAR load. | ||
Diesel Handswitch Name Handswitch No. Panel DG 3C GOVERNOR 3-HS CONTROL 3C/3A 3C 3-9-23 DG 3C VOLT REGULATOR 3-HS CONT 3C/2A 11 | |||
[17] | Job Performance Measure (JPM) | ||
[18] | STEP / STANDARD SAT / | ||
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVAR limit may result in a reverse power trip of the Diesel Generator output breaker. | UNSAT Standard: | ||
[18.1] | Obtains desired kW and kVAR load using DG 3C Governor Control switch, 3-HS-82-3C/3A and DG Volt Regulator Control switch, 3-HS-82-3C/2A CUE: state 30 minutes have elapsed continue with procedure. | ||
Step 16: | |||
[16] MONITOR the offsite source that is paralleled with the Diesel Generator. SAT | |||
[17] IF abnormal voltage or frequency transients are experienced, UNSAT THEN N/A Standard: | |||
Step is N/A Step 17: | |||
[18] WHEN Parallel with System operation is no longer desired, THEN UNLOAD the Diesel Generator as follows: | |||
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVAR limit may result in a reverse power trip of the Diesel Generator output breaker. Critical Step SAT | |||
[18.1] USE the associated Diesel Generator's governor control switch and voltage regulator control switch to reduce UNSAT generator load to approximately 300 kW and 250 kVAR: N/A Diesel Instrument Name Inst No. Panel DG 3C GOVERNOR CONTROL 3-HS-82-3C/3A DG 3C VOLT REGULATOR 3-HS-82-3C/2A 3C 3-9-23 CONT DG 3C KILOWATTS 3-JI-82-3C/A DG 3C KILOVARS 3-VAR-82-3C/A 12 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / | |||
UNSAT Step 17 continued: | |||
. | Standard: | ||
Unloads the DG to approximately 300 KW and 250 kVAR Step 18: | |||
[18.2] PLACE the associated Diesel Generator breaker control Critical Step switch in TRIP. | |||
SAT Diesel Handswitch Name Handswitch No. Panel 3C DG 3C BKR 1832 3-HS-211- 3-9-23 UNSAT 3EC/10A N/A Standard: | |||
Trips breaker DG 3C BKR 1832 Step 19: | |||
[18.3] PULL and PLACE the associated Diesel Generator mode Critical Step selector switch in SINGLE UNIT. | |||
- | SAT Diesel Handswitch Name Handswitch No. Panel 3C DG 3C MODE SELECT 3-HS-82-3C/5A 0-9-23 UNSAT Standard: N/A Pulls and places 3-HS-82-3C/5A to Single Unit Step 20: SAT | ||
- | [18.4] RELEASE the Diesel Generator mode selector switch and UNSAT OBSERVE the SINGLE UNIT light illuminated. | ||
-23 | N/A Standard: | ||
Verifies Single Unit light illuminated CUE: ANOTHER OPERATOR WILL CONTINUE FROM HERE STOP TIME END OF TASK 13 | |||
- | |||
- | |||
- | |||
Job Performance Measure (JPM) | |||
Provide to Applicant INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* No Inclement weather currently exists in the area | |||
* 8 hours ago, 4 KV Shutdown Board 3EC was separated from Offsite Power in accordance with 3-OI-82, Standby Diesel Generator System. | |||
INITIATING CUE: | |||
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board 3EC using the normal feeder breaker and remove DG 3C from parallel operation in accordance with 3-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23. | |||
14 | |||
Job Performance Measure (JPM) | |||
SITE: BFN JPM TITLE: Respond to Off-Gas Post Treatment Radiation HI-HI-HI JPM NUMBER: 190 U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-066-AB-02 -Respond to Off-Gas Post Treatment TASK NUMBER / TASK TITLE(S): | |||
( | Radiation Hi-Hi-Hi K/A RATINGS: RO 2.9 SRO 3.2 271000 Offgas System: A2.16; Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those K/A STATEMENT: predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2) | ||
RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: N/A TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Validated by: | |||
Validator Date Approved by: | |||
Site Training Management Date Approved by: | |||
Site Training Program Owner Date 1 | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: 190 U2 RO SRO DATE: _______ | |||
TASK STANDARD: Respond to Off-Gas Post Treatment Radiation HI-HI-HI per 2-AOI-66-2 and/or 2-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-66-2, 2-ARP-9-4C/35 VALIDATION TIME: 15 Minutes PERFORMANCE TIME: | |||
: | COMMENTS: | ||
: | Additional comment sheets attached? YES ___ NO ___ | ||
: | RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | ||
- | SIGNATURE: ___________________________ DATE: __________ | ||
EXAMINER 2 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
SIMULATOR SETUP IC 28 Exam IC 287 | |||
: 1. Reset to IC 28 Console 2. Fire Manual Trigger 2 Operator 3. Fire Manual Trigger 1 Instructions 4. Station 2nd operator to respond to alarms Malfunctions Description Event Severity Delay Initial set TH23 FUEL CLADDING 1 50 N/A YES DAMAGE RM14C OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURERM 265A RM14D OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-266A Remotes Description Event Severity Delay Initial set OG06 Bypass FCV-66-28 2 N/A N/A BYP Post Treatment Hi-Hi-Hi Rad Isol Overrides Description Event Severity Delay Initial set ZAORI9014A RX BLDG AREA 1 2.5 N/A YES RAD ZAORI9017A RX BLDG AREA 1 2.6 N/A YES RAD ZAORM90265A 90-265 METER 1 6.0 N/A YES UPSCALE ZAORM90266A 90-266 METER 1 6.0 N/A YES UPSCALE ZAORR90135R1 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90135R2 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZLORM90265A_1 90-265 DRAW LITE 1 N/A N/A YES 3 | |||
Job Performance Measure (JPM) | |||
ZLORM90265A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_4 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_4 90-265 DRAW LITE 1 N/A N/A YES XA553A5 OG PRETREAT 1 N/A N/A YES RAD HI XA553A6 STACK GAS RAD 1 N/A N/A YES HI HI XA553A7 MSL RAD HI 1 N/A N/A YES XA553A13 STACK GAS RAD 1 N/A N/A YES HI XA553A27 MSL RAD HI HI 1 N/A N/A YES XA554C26 CARBON BED 1 N/A N/A YES VAULT RAD HI XA554C27 OG ANNUAL 1 N/A N/A YES RELEASE LIMIT EXCEEDED XA554C33 OG POST TREAT 1 N/A N/A YES RAD HI XA554C34 OG POST TREAT 1 N/A N/A YES RAD HI HI XA554C35 OG POST TREAT 1 N/A N/A YES RAD HI HIHI ZDIHS6628 66-28 VALVE 1 N/A N/A YES CLOSED ZAORR90265R1 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90265R2 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZAORR90160R1 OG PRETREAT 1 -2.0 N/A YES RECORDER UPSCALE XA554B2 RWCU FILTER 1 N/A N/A YES INLET CNDT HIGH Schedule File(s): JPM 190 U2 OG Post treat Rad HI HIHI 4 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are the Unit 2 Operator. Unit 2 is at 100% power. | You are the Unit 2 Operator. Unit 2 is at 100% power. | ||
INITIATING CUE: | |||
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 2-XA-55-4C, window 35. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / UNSAT Performance Step 1: | |||
SAT When directed, identify/obtain copy of ARP-9-4C, window 35. | |||
UNSAT Standard: | |||
N/A Obtains copy of 2-ARP-9-4C, window 35 Examiner Note: Candidate may recognize the annunciator as an entry condition and go directly to 2-AOI-66-2. In that event, continue at Performance Step 5. | |||
Performance Step 2: | |||
2-ARP-9-4C window 35 Operator Action: | |||
A. VERIFY alarm condition on the following | |||
* OFFGAS POST-TREATMENT RADIATION recorder, SAT 2-RR-90-265 on Panel 2-9-2. | |||
* OG POST-TREATMENT CHAN A RAD MON RTMR UNSAT radiationmonitor, 2-RM-90-266A on Panel 2-9-10. | |||
* OG POST-TREATMENT CHAN B RAD MON RTMR N/A radiationmonitor, 2-RM-90-265A on Panel 2-9-10. | |||
Standard: | |||
Verified alarm condition on 2-RR-90-265 and 2-RM-265/266. | |||
Performance Step 3: | |||
B. VERIFY OFF-GAS SYSTEM ISOLATION VALVE, 2-FCV- Critical Step 66-28 has the Mechanical Restraint DISENGAGED and 2-FCV-66-28 isCLOSED. SAT Standard: UNSAT Takes handswitch 2-FCV-66-28 to close and observes green light N/A illuminated and red light out. | |||
Cue: If asked, the Offgas Isolation Valve, 2-FCV-66-28 is NOT mechanically restrained. | |||
6 | |||
Job Performance Measure (JPM) | |||
- | STEP / STANDARD SAT / UNSAT Performance Step 4: | ||
- | C. REFER to 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-SAT Hi-Hi UNSAT Standard: | ||
N/A Refers to 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 5: | |||
2-AOI-66-2 4.0 OPERATOR ACTIONS 4.1 Immediate Actions Critical Step | |||
[1] IF scram has not occurred, THEN SAT PERFORM the following: | |||
UNSAT | |||
[1.1] IF core flow is above 60%, THEN N/A REDUCE core flow to between 50-60%. | |||
Standard: | |||
Reduced core flow to between 50-60% with recirc system. | |||
Performance Step 6: | |||
[1.2] MANUALLY SCRAM the Reactor. (Reference 2-AOI-100-1). | |||
Standard: | Standard: | ||
Critical Step | |||
* Depresses both SCRAM Pushbuttons | |||
* Places mode switch in shutdown SAT | |||
* Verifies All Rods in | |||
* Performs a Scram Announcement UNSAT o Rx Mode Switch Position: Shutdown N/A o Rod Position: All Full In o Reactor Water Level ____ & Trend ___ | |||
o Reactor Pressure ____ & Trend ___ | |||
o MSIV Position: OPEN o Rx Power: <5% | |||
Examiner Note: The scram report and referring to 2-AOI-100-1 are not considered critical. | |||
7 | |||
- | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT CUE: Proceed with subsequent actions of 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 7: | |||
4.2 Subsequent Actions | |||
[1] IF OFFGAS SYSTEM ISOLATION VALVE, 2-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN SAT DISENGAGE 2-FCV-066-0028 mechanical restraint by UNSAT rotating the restraining handwheel fully in the counterclockwisedirection, locally at the Stack. (Otherwise N/A N/A) | |||
Job Performance Measure (JPM) | |||
-AOI-66-2, Off-gas Post-treatment Radiation Hi | |||
-Hi-Hi Performance Step 7: | |||
[1] | |||
-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN DISENGAGE 2-FCV-066-0028 mechanical restraint by rotating the restraining handwheel fully in the | |||
Standard: | Standard: | ||
Verifies 2-FCV-66-28 is closed at panel 9 | Verifies that 2-FCV-066-0028 in NOT mechanically restrained. | ||
-53 by Verifying RED light above handswitch extinguished and GREEN light above handswitch illuminated. (May have already verified valve closed from the ARP). | Cue: 2-FCV-066 is NOT mechanically restrained. | ||
Performance Step 8: | |||
[3] | [2] VERIFY CLOSED OFFGAS SYSTEM ISOLATION VALVE, Critical Step 2-FCV-66-28 on Panel 2-9-53 or locally. | ||
Monitored radiation levels at Panel 9 | SAT Standard: | ||
-11. | UNSAT Verifies 2-FCV-66-28 is closed at panel 9-53 by Verifying RED light above handswitch extinguished and GREEN light above N/A handswitch illuminated. (May have already verified valve closed from the ARP). | ||
Examiner Note: May have already verified valve closed from the ARP Performance Step 9: | |||
[3] MONITOR area radiation levels at Panel: 2-9-11. SAT Standard: UNSAT Monitored radiation levels at Panel 9-11. N/A Cue: Another operator will monitor and evaluate Area Radiation Levels. | |||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-1. | STEP / STANDARD SAT / UNSAT Performance Step 10: | ||
[4] REFER TO EPIP-1 for emergency classification level and SAT response. | |||
UNSAT Standard; N/A Notifies SM to implement EPIP-1. | |||
Cue: The Shift Manager is implementing the EPIPs as needed. | |||
Performance Step 11: | Performance Step 11: | ||
[5] | [5] MONITOR the following parameters: | ||
A. MAIN STEAM LINE RADIATION, 2 | A. MAIN STEAM LINE RADIATION, 2-RR-90-135, Panel 2-9-2. | ||
-RR-90-135, | B. OFFGAS PRETREATMENT RADIATION 2-RR 157, Pnl 2-9-2. SAT C. OFFGAS POST-TREATMENT RADIATION 2RR- UNSAT 90-265, Pnl 2-9-2 N/A D. STACK GAS RADIATION, 0-RR-90-147, Unit 1 Panel 1-9-2. | ||
B. OFFGAS PRETREATMENT RADIATION 2 | Standard; Monitors 90-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147. | ||
-RR | Cue: As Unit 1 Operator, Stack Gas Radiation, 0-RR-90-147 is reading 5X10E6 cps. | ||
- | 9 | ||
-RR-90-147, Unit 1 Panel 1-9-2. Standard; Monitors | |||
-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147. | |||
-RR-90-147 is reading 5X10E6 cps. | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
[6] | STEP / STANDARD SAT / UNSAT Performance Step 12: | ||
-RR-90-266 on panel 2 2, THEN | [6] IF after five minutes from scram the Offgas Post Treatment activity is not less than 6 x 10E5 cps as indicated on OFFGASRADIATION recorder 2-RR-90-266 on panel 2 Critical Step 2, THEN SAT CLOSE all Main Steam Isolation Valves and Main Steam LineDrain Valves, 2-FCV-1-55 and 2-FCV-1-56. | ||
-FCV-1-55 and 2-FCV-1-56. Standard: | UNSAT Standard: | ||
-Gas Post Treatment activity is >6 X | N/A Recognizes that the Off-Gas Post Treatment activity is >6 X 10E5 and closes all Main Steam Isolation Valves and Main Steam Line Drain Valves (2-FCV-1-55/56) | ||
-FCV-1-55/56) | Cue: The Unit has been scrammed for 5 minutes. | ||
Acknowledge closing of MSIVs. | * Acknowledge closing of MSIVs. | ||
Examiner Note: | Examiner Note: Closing 1-55 and 1-56 is not considered critical. | ||
Closing 1-55 and 1-56 is not considered critical. | |||
Performance Step 13: | Performance Step 13: | ||
NOTE Placing additional Stack Dilution Air Fans in service should keep 0-RM-90-147and 0-RM-90-148 on scale. | |||
[7] PLACE STACK DILUTION FAN SEL control switch, SAT 2-XS-66-29, Panel 2-9-8, in OFF. | |||
UNSAT | |||
[8] START standby STACK DILUTION FAN 2B(2A) using controlswitch, 2-HS-66-31A(29A), Panel 2-9-8. N/A Standard: | |||
Places 2-XS-66-29 in OFF and Starts standby Stack Dilution fan 2B, using 2-HS-66-31A Cue: That completes this task. | |||
STOP TIME _______ | |||
END OF TASK 10 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
Job Performance Measure (JPM) | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are the Unit 2 Operator. Unit 2 is at 100% power. | You are the Unit 2 Operator. Unit 2 is at 100% power. | ||
INITIATING CUE: | |||
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 2-XA-55-4C, window 35. | |||
11 | |||
Job Performance Measure (JPM) | |||
SITE: BFN JPM TITLE: Respond to Off-Gas Post Treatment Radiation HI-HI-HI JPM NUMBER: 190 U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-066-AB-02 -Respond to Off-Gas Post Treatment TASK NUMBER / TASK TITLE(S): | |||
Radiation Hi-Hi-Hi K/A RATINGS: RO 2.9 SRO 3.2 271000 Offgas System: A2.16;Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the K/A STATEMENT: | |||
consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2) | |||
RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: N/A TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
Job Performance Measure (JPM) | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
Respond to Off | Validated by: | ||
-Gas Post Treatment Radiation HI | Validator Date Approved by: | ||
-HI-HI JPM NUMBER: | Site Training Management Date Approved by: | ||
190 U3 REVISION: 0 | Site Training Program Owner Date 1 | ||
SRO STA UO NAUO | |||
U-066-AB-02 -Respond to Off | |||
-Gas Post Treatment Radiation Hi | |||
-Hi-Hi K/A RATINGS: | |||
RO 2.9 | |||
271000 Offgas System | |||
: A2.16;Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2) | |||
N/A SAFETY FUNCTION: | |||
9 | |||
In-Plant | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
TASK STANDARD: | Job Performance Measure (JPM) | ||
Respond to Off | OPERATOR: ________________________________ JPM Number: 190 RO SRO DATE: _______ | ||
-Gas Post Treatment Radiation HI | TASK STANDARD: Respond to Off-Gas Post Treatment Radiation HI-HI-HI per 3-AOI-66-2 and/or 3-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: 3-AOI-66-2, 3-ARP-9-4C/35 VALIDATION TIME: 15 Minutes PERFORMANCE TIME: | ||
-HI-HI per 3-AOI-66-2 and/or 3-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: | COMMENTS: | ||
3-AOI-66-2, 3-ARP-9-4C/35 VALIDATION TIME: 15 Minutes | Additional comment sheets attached? YES ___ NO ___ | ||
COMMENTS: | RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records) | ||
SIGNATURE: ___________________________ DATE: __________ | |||
Additional comment sheets attached? | EXAMINER 2 | ||
RESULTS: SATISFACTORY ____ | |||
UNSATISFACTORY ____ | |||
(Retain entire JPM for records) | |||
SIGNATURE: ___________________________ | |||
DATE: __________ | |||
EXAMINER | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
SIMULATOR SETUP IC 28 Exam IC 288 | |||
: 1. Reset to IC 28 Console 2. Fire Manual Trigger 2 Operator 3. Fire Manual Trigger 1 Instructions 4. Station 2nd operator to respond to alarms Malfunctions Description Event Severity Delay Initial set TH23 FUEL CLADDING 1 50 N/A YES DAMAGE RM14C OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-265A RM14D OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-266A Remotes Description Event Severity Delay Initial set OG06 Bypass FCV-66-28 2 N/A N/A BYP Post Treatment Hi-Hi-Hi Rad Isol Overrides Description Event Severity Delay Initial set ZAORI9014A RX BLDG AREA 1 2.5 N/A YES RAD ZAORI9017A RX BLDG AREA 1 2.6 N/A YES RAD ZAORM90265A 90-265 METER 1 6.0 N/A YES UPSCALE ZAORM90266A 90-266 METER 1 6.0 N/A YES UPSCALE ZAORR90135R1 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90135R2 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZLORM90265A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_2 90-265 DRAW LITE 1 N/A N/A YES 3 | |||
Job Performance Measure (JPM) | |||
ZLORM90265A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_4 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_4 90-265 DRAW LITE 1 N/A N/A YES XA553A5 OG PRETREAT 1 N/A N/A YES RAD HI XA553A6 STACK GAS RAD 1 N/A N/A YES HI HI XA553A7 MSL RAD HI 1 N/A N/A YES XA553A13 STACK GAS RAD 1 N/A N/A YES HI XA553A27 MSL RAD HI HI 1 N/A N/A YES XA554C26 CARBON BED 1 N/A N/A YES VAULT RAD HI XA554C27 OG ANNUAL 1 N/A N/A YES RELEASE LIMIT EXCEEDED XA554C33 OG POST TREAT 1 N/A N/A YES RAD HI XA554C34 OG POST TREAT 1 N/A N/A YES RAD HI HI XA554C35 OG POST TREAT 1 N/A N/A YES RAD HI HIHI ZDIHS6628 66-28 VALVE 1 N/A N/A YES CLOSED ZAORR90265R1 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90265R2 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZAORR90160R1 OG PRETREAT 1 -2.0 N/A YES RECORDER UPSCALE XA554B2 RWCU FILTER 1 N/A N/A YES INLET CNDT HIGH Schedule File(s): JPM 190 U3 OG Post treat Rad HI HIHI 4 | |||
Job Performance Measure (JPM) | |||
IN-SIMULATOR: | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are the Unit 3 Operator. Unit 3 is at 100% power. | You are the Unit 3 Operator. Unit 3 is at 100% power. | ||
INITIATING CUE: | |||
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 3-XA-55-4C, window 35. | |||
5 | |||
Job Performance Measure (JPM) | |||
START TIME STEP / STANDARD SAT / UNSAT Performance Step 1: | |||
SAT When directed, identify/obtain copy of ARP-9-4C, window 35. | |||
UNSAT Standard: | |||
N/A Obtains copy of 3-ARP-9-4C, window 35 Examiner Note: Candidate may recognize the annunciator as an entry condition and go directly to 3-AOI-66-2. In that event, continue at Performance Step 5. | |||
Performance Step 2: | |||
3-ARP-9-4C window 35 Operator Action: | |||
A. VERIFY alarm condition on the following | |||
* OFFGAS POST-TREATMENT RADIATION recorder, SAT 3-RR-90-265 on Panel 3-9-2. | |||
* OG POST-TREATMENT CHAN A RAD MON RTMR UNSAT radiationmonitor, 3-RM-90-266A on Panel 3-9-10. | |||
* OG POST-TREATMENT CHAN B RAD MON RTMR N/A radiationmonitor, 3-RM-90-265A on Panel 3-9-10. | |||
Standard: | |||
Verified alarm condition on 3-RR-90-265 and 3-RM-265/266. | |||
Performance Step 3: | |||
B. VERIFY OFF-GAS SYSTEM ISOLATION VALVE, 3-FCV- Critical Step 66-28 has the Mechanical Restraint DISENGAGED and 3-FCV-66-28 isCLOSED. SAT Standard: UNSAT Takes handswitch 3-FCV-66-28 to close and observes green light N/A illuminated and red light out. | |||
Cue: If asked, the Offgas Isolation Valve, 3-FCV-66-28 is NOT mechanically restrained. | |||
6 | |||
Job Performance Measure (JPM) | |||
- | STEP / STANDARD SAT / UNSAT Performance Step 4: | ||
C. REFER to 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi SAT Standard: UNSAT Refers to 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi N/A Performance Step 5: | |||
3-AOI-66-2 4.0 OPERATOR ACTIONS 4.1 Immediate Actions Critical Step | |||
[1] IF scram has not occurred, THEN SAT PERFORM the following: | |||
UNSAT | |||
[1.1] IF core flow is above 60%, THEN N/A REDUCE core flow to between 50-60%. | |||
Standard: | |||
Reduced core flow to between 50-60% with recirc system. | |||
Performance Step 6: | |||
[1.2] MANUALLY SCRAM the Reactor. (Reference 3-AOI-100-1). | |||
Standard: | Standard: | ||
Critical Step | |||
* Depresses both SCRAM Pushbuttons | |||
* Places mode switch in shutdown SAT | |||
* Verifies All Rods in | |||
* Performs a Scram Announcement UNSAT o Rx Mode Switch Position: Shutdown N/A o Rod Position: All Full In o Reactor Water Level ____ & Trend ___ | |||
o Reactor Pressure ____ & Trend ___ | |||
o MSIV Position: OPEN o Rx Power: <5% | |||
Examiner Note: The scram report and referring to 3-AOI-100-1 are not considered critical. | |||
7 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT CUE: Proceed with subsequent actions of 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 7: | |||
4.2 Subsequent Actions | |||
[1] IF OFFGAS SYSTEM ISOLATION VALVE, 3-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN SAT DISENGAGE3-FCV-066-0028 mechanical restraint by UNSAT rotating the restraining handwheel fully in the counterclockwisedirection, locally at the Stack. (Otherwise N/A N/A) | |||
Job Performance Measure (JPM) | |||
-AOI-66-2, Off-gas Post-treatment Radiation Hi | |||
-Hi-Hi Performance Step 7: | |||
[1] | |||
Standard: | Standard: | ||
Verifies 3-FCV-66-28 is closed at panel 9 | Verifies that 3-FCV-066-0028 in NOT mechanically restrained. | ||
-53 by Verifying RED light above handswitch extinguished and GREEN light above handswitch illuminated. (May have already verified valve closed from the ARP). | Cue: 3-FCV-066 is NOT mechanically restrained. | ||
Performance Step 8: | |||
[3] | [2] VERIFY CLOSED OFFGAS SYSTEM ISOLATION VALVE, Critical Step 3-FCV-66-28 on Panel 3-9-53 or locally. | ||
3-9-11. Standard: | SAT Standard: | ||
Monitored radiation levels at Panel 9 | UNSAT Verifies 3-FCV-66-28 is closed at panel 9-53 by Verifying RED light above handswitch extinguished and GREEN light above N/A handswitch illuminated. (May have already verified valve closed from the ARP). | ||
-11. | Examiner Note: May have already verified valve closed from the ARP Performance Step 9: | ||
SAT | |||
[3] MONITOR area radiation levels at Panel: 3-9-11. | |||
UNSAT Standard: | |||
N/A Monitored radiation levels at Panel 9-11. | |||
Cue: Another operator will monitor and evaluate Area Radiation Levels. | |||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-1. | STEP / STANDARD SAT / UNSAT Performance Step 10: | ||
[4] REFER TO EPIP-1 for emergency classification level and SAT response. | |||
UNSAT Standard; N/A Notifies SM to implement EPIP-1. | |||
Cue: The Shift Manager is implementing the EPIPs as needed. | |||
Performance Step 11: | Performance Step 11: | ||
[5] | [5] MONITOR the following parameters: | ||
A. MAIN STEAM LINE RADIATION, 3-RR-90-135, | A. MAIN STEAM LINE RADIATION, 3-RR-90-135, Panel 3-9-2. | ||
B. OFFGAS PRETREATMENT RADIATION 3-RR | B. OFFGAS PRETREATMENT RADIATION 3-RR 157, Pnl3-9-2. SAT C. OFFGAS POST-TREATMENT RADIATION 3-RR- UNSAT 90-265, Pnl3-9-2 N/A D. STACK GAS RADIATION, 0-RR-90-147, Unit 1 Panel 1-9-2. | ||
-RR-90-147, Unit 1 Panel 1-9-2. Standard; Monitors | Standard; Monitors 90-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147. | ||
-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147. | Cue: As Unit 1 Operator, Stack Gas Radiation, 0-RR-90-147 is reading 5X10E6 cps. | ||
-RR-90-147 is reading 5X10E6 cps. | 9 | ||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
[6] | STEP / STANDARD SAT / UNSAT Performance Step 12: | ||
-Gas Post Treatment activity is >6 X | [6] IF after five minutes from scram the Offgas Post Treatment activity is not less than 6 x 10E5 cps as indicated on OFFGASRADIATION recorder 3-RR-90-265 on panel 3 2, THEN Critical Step CLOSE all Main Steam Isolation Valves and Main Steam SAT LineDrain Valves, 3-FCV-1-55 and 3-FCV-1-56. | ||
Acknowledge closing of MSIVs. | UNSAT Standard: | ||
N/A Recognizes that the Off-Gas Post Treatment activity is >6 X 10E5 and closes all Main Steam Isolation Valves and Main Steam Line Drain Valves (3-FCV-1-55/56) | |||
Cue: The Unit has been scrammed for 5 minutes. | |||
* Acknowledge closing of MSIVs. | |||
Examiner Note: Closing 1-55 and 1-56 is not considered critical. | Examiner Note: Closing 1-55 and 1-56 is not considered critical. | ||
Performance Step 13: | Performance Step 13: | ||
NOTE Placing additional Stack Dilution Air Fans in service should keep 0-RM-90-147and 0-RM-90-148 on scale. | |||
NOTE Placing additional Stack Dilution Air Fans in service should keep 0 | [7] PLACE STACK DILUTION FAN SEL control switch, SAT 3-XS-66-29, Panel 3-9-8, in OFF. | ||
-RM-90-147and 0-RM-90-148 on scale. | UNSAT | ||
[7] | [8] START standby STACK DILUTION FAN 3B(3A) using controlswitch, 3-HS-66-31A(29A), Panel 3-9-8. N/A Standard: | ||
[8] | Places 3-XS-66-29 in OFF and Starts standby Stack Dilution fan 3B, using 3-HS-66-31A Cue: That completes this task. | ||
Places 3-XS-66-29 in OFF and Starts standby Stack Dilution fan 3B, using 3-HS-66-31A | |||
STOP TIME ________ | STOP TIME ________ | ||
END OF TASK | END OF TASK 10 | ||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-SIMULATOR: | |||
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | INITIAL CONDITIONS: | ||
You are the Unit 3 Operator. Unit 3 is at 100% power. | You are the Unit 3 Operator. Unit 3 is at 100% power. | ||
INITIATING CUE: | |||
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 3-XA-55-4C, window 35. | |||
11 | |||
Job Performance Measure (JPM) | |||
SITE: BFN JPM TITLE: AUTOMATIC START FAILURE OF A & C FIRE PUMPS JPM NUMBER: 673 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-026-NO-01/ MONITOR AUTO START OF FIRE TASK NUMBER / TASK TITLE(S): | |||
PUMP K/A RATINGS: RO: 3.4 SRO: 3.4 286000 Fire Protection System A2.08; Ability to (a) predict the impacts of the following on the FIRE PROTECTION SYSTEM; K/A No. &STATEMENT: and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Failure to actuate when required RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 8 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by: | |||
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | |||
(See JPM Validation Checklist in NPG-SPP-17.8.2) | |||
Job Performance Measure (JPM) | Validated by: | ||
AUTOMATIC START FAILURE OF A & C FIRE | Validator Date Approved by: | ||
673 REVISION: | Site Training Management Date Approved by: | ||
SRO STA UO NAUO | Site Training Program Owner Date 1 | ||
U-026-NO-01/ MONITOR AUTO START OF FIRE PUMP | |||
RO: | |||
286000 Fire Protection System | |||
Risk Significant SAFETY FUNCTION: | |||
8 | |||
In-Plant | |||
ALTERNATE PATH (Y/N) | |||
Developed by: | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _673A___ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to manually start A, B and C Fire Pumps. | |||
Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 0-OI-26 VALIDATIONTIME:__15 min PERFORMANCE TIME: | ||
0-OI-26 | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 04/28/15 All Initial issue 3 | |||
Job Performance Measure (JPM) | |||
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 1. | |||
* The Reactor Power at 70% | |||
* A Fire Exists on B Reactor Feed Pump Lube Oil Reservoir. | |||
* Fire OPS has been dispatched to the scene. | |||
* Fire Pump B Tagged Out for Maintenance | |||
* A and C Fire Pumps failed to Auto Start. | |||
INITIATING CUES: | |||
The US directs you to start A and C Electric Fire Pumps per 0-OI-26 section 5.4. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
-XS-26-1 in EMERGENCY position, at the respective switchgear. | START TIME: | ||
Pump Board Compt A 4160V Shutdown Bd A 11 C 4160V Shutdown Bd C 10 | STEP / STANDARD SAT / UNSAT Step 1: | ||
-XS-26-3 in EMERGENCY position at 4160 Shutdown Board A, Compartment | [1] PLACE the FIRE PUMP A TRANSFER switch, 0-XS-26-1 in EMERGENCY position, at the respective switchgear. | ||
Critical Step Pump Board Compt A 4160V Shutdown Bd A 11 SAT C 4160V Shutdown Bd C 10 UNSAT Standard: | |||
11 | N/A Simulates placing FIRE PUMP A TRANSFER switch 0-XS-26-3 in EMERGENCY position at 4160 Shutdown Board A, Compartment 11 CUE: FIRE PUMP A TRANSFER switch 0-XS-26-1 is in the EMERGENCY position Step 2: | ||
-XS-26-1 is in the EMERGENCY position Step 2: | |||
Critical Step | Critical Step | ||
[2] CLOSE the breaker by placing the FIRE PUMP A CONTROL switch, 0-HS-26-1C to CLOSE. SAT Standard: UNSAT Simulates placing FIRE PUMP A CONTROL switch, 0-HS-26-1C N/A to CLOSE position. | |||
SAT | CUE: Breaker Red indicating light is ON with Green and Amber lights are OFF. | ||
Breaker Flag indicates CLOSED with Charging Spring indicating CHARGED. | |||
Step 3: | Step 3: | ||
[3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. Standard | [3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. SAT Standard UNSAT VERIFIES pump ammeter at breaker indicates between 25 and N/A 40 amps. | ||
CUE: FIRE PUMP A ammeter at breaker indicates 30 amps. | |||
5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Standard | Step 4: | ||
[1] PLACE the FIRE PUMP C TRANSFER switch, 0 | [4] PLACE the NORM/EMERG Switch in NORMAL. | ||
-XS-26-3 in EMERGENCY position, at the respective switchgear. | SAT Standard UNSAT PLACES the NORM/EMERG Switch in NORMAL for FIRE N/A PUMP A. | ||
Pump Board Compt A 4160V Shutdown Bd A 11 C 4160V Shutdown Bd C 10 | CUE: FIRE PUMP A NORM/EMERG Switch is in NORMAL Step 5: | ||
-XS-26-3 in EMERGENCY position at 4160 Shutdown Board C, Compartment | [1] PLACE the FIRE PUMP C TRANSFER switch, 0-XS-26-3 in EMERGENCY position, at the respective switchgear. | ||
Critical Step Pump Board Compt A 4160V Shutdown Bd A 11 SAT C 4160V Shutdown Bd C 10 UNSAT Standard: | |||
10 | N/A Simulates placing FIRE PUMP C TRANSFER switch 0-XS-26-3 in EMERGENCY position at 4160 Shutdown Board C, Compartment 10 CUE: FIRE PUMP C TRANSFER switch 0-XS-26-3 is in the EMERGENCY position Step 5: | ||
Critical Step | |||
-XS-26-3 is in the EMERGENCY position Step 5: | |||
[2] CLOSE the breaker by placing the FIRE PUMP C CONTROL switch, 0-HS-26-3C to CLOSE. | [2] CLOSE the breaker by placing the FIRE PUMP C CONTROL switch, 0-HS-26-3C to CLOSE. | ||
Standard: | SAT Standard: | ||
-HS-26-3C to CLOSE position. | UNSAT Simulates placing FIRE PUMP C CONTROL switch, 0-HS-26-3C N/A to CLOSE position. | ||
CUE: Breaker Red indicating light is ON with Green and Amber lights are OFF. | |||
Breaker Flag indicates CLOSED with Charging Spring indicating CHARGED. | |||
6 | |||
Job Performance Measure (JPM) | |||
Step 6: | |||
Job Performance Measure (JPM) | [3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. SAT Standard UNSAT VERIFIES pump ammeter at breaker indicates between 25 and N/A 40 amps. | ||
CUE: FIRE PUMP C ammeter at breaker indicates 30 amps. | |||
Step 7: | Step 7: | ||
[4] PLACE the NORM/EMERG Switch in NORMAL. | [4] PLACE the NORM/EMERG Switch in NORMAL. | ||
Standard | SAT Standard UNSAT PLACES the NORM/EMERG Switch in NORMAL for FIRE N/A PUMP C. | ||
CUE: FIRE PUMP C NORM/EMERG Switch is in NORMAL and this completes the JPM. | |||
Termination Criteria: When two Fire Pumps are in service the JPM is complete. | |||
STOP TIME: | STOP TIME: | ||
7 | |||
Job Performance Measure (JPM) | |||
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 1. | |||
* The Reactor Power at 70% | |||
* A Fire Exists on B Reactor Feed Pump Lube Oil Reservoir. | |||
* Fire OPS has been dispatched to the scene. | |||
* Fire Pump B Tagged Out for Maintenance | |||
* A and C Fire Pumps failed to Auto Start. | |||
INITIATING CUES: | |||
The US directs you to start A and C Electric Fire Pumps per 0-OI-26 section 5.2. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
ALIGNING EMERGENCY EECW MAKEUP TO SPENT SITE: BFN JPM TITLE: | |||
674 REVISION: 0 | FUEL POOL JPM NUMBER: 674 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-95/ Make-Up To SFP By EECW With TASK NUMBER / TASK TITLE(S): | ||
SRO STA UO NAUO | Fire Hose (Internal Make-Up) | ||
U-000-EM-95/ Make-Up To SFP By EECW With Fire Hose (Internal Make | K/A RATINGS: RO: 3.1 SRO: 3.3 233000 Fuel Pool Cooling and Clean-up; A2.02; Ability to (a) predict the impacts of the following on the FUEL POOL COOLING AND CLEAN-UP ; and (b) based on those K/A No. &STATEMENT: | ||
-Up) | predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Low pool level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | ||
RO: | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
233000 Fuel Pool Cooling and Clean | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
-up; A2.02; Ability to (a) predict the impacts of the following on the FUEL POOL COOLING AND | Validated by: | ||
Low pool level RELATED PRA INFORMATION: | Validator Date Approved by: | ||
Risk Significant SAFETY FUNCTION: | Site Training Management Date Approved by: | ||
9 | Site Training Program Owner Date 1 | ||
ALTERNATE PATH (Y/N) | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: __674__ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to align either North or South Headers of EECW to Unit 2 Spent Fuel Pool. | |||
Operator Fundamental evaluated: | |||
OF-2 Controlling plant evolutions and indications closely. | OF-2 Controlling plant evolutions and indications closely. | ||
OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | OF-5 Having a solid understanding of plant design, engineering principles, and sciences. | ||
PRA: NA REFERENCES/PROCEDURES NEEDED: | PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-78-1 VALIDATION TIME: 25 min PERFORMANCE TIME: | ||
2-AOI-78-1 VALIDATION TIME: | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 3 | |||
Job Performance Measure (JPM) | |||
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 2. | |||
* The Reactor is in cold shutdown | |||
* The Unit 2 Spent Fuel Pool water level is lowering. | |||
* Fire Protection is available to assist INITIATING CUES: | |||
The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3]. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
NORTH HDR SPLY TO EMER FUEL POOL MU, 1 | START TIME: | ||
-SHV-067-0792. SOUTH HDR SPLY TO EMER FUEL POOL MU, 1 | STEP / STANDARD SAT / UNSAT Step 1: | ||
-SHV-067-0793. Standard: | NOTES | ||
-SHV-067-0793 by demonstrating opening each valve | : 1) Hose straps are staged at the hoses at the following locations: | ||
* Unit 1/Unit 2 Reactor Bldg Stairwell, El. 621, R6 U Line (placed on hose to carry weight of charged hose lines). | |||
-SHV-067-0792 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1 | * Hose reel on the Refuel Floor, El. 664, R6 U Line (for use in securing hose ends as needed). | ||
-SHV-067-0793 is OPEN | : 2) Additional hose is stored in a cabinet located in Unit 1/Unit 2 Elevator Room, Reactor Bldg, El 595. | ||
Hoses are already connected, no tools required. | Critical Step CAUTION Performance of this attachment will degrade water chemistry in the SAT Spent Fuel Pool. | ||
UNSAT | |||
[3] UNLOCK and OPEN the following valves: | |||
N/A | |||
* NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792. | |||
* SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793. | |||
Standard: | |||
Simulates opening NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792 and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793 by demonstrating opening each valve counter-clockwise and breaking seal. | |||
CUE: NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793 is OPEN Located in stairwell between elevation 565 ft and 593 ft. Hoses are already connected, no tools required. | |||
5 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Step 3: | |||
[4] VERIFY charged hoses in stairwell are not obstructing stairway access and/or kinked. | |||
SAT | |||
[4.1] ADJUST hose straps, as necessary. | [4.1] ADJUST hose straps, as necessary. | ||
Standard: | UNSAT Standard: | ||
Hoses are already run along the stairwell. Applicant should verify hoses not kinked and connected. | N/A VERIFIES hoses in stairwell are not kinked Note to Examiner: Hoses are already run along the stairwell. Applicant should verify hoses not kinked and connected. | ||
Step 4: | Step 4: | ||
-SHV-067-0796 and route to Unit 2 Spent Fuel Pool (El 664 | [5] VERIFY hose connected from NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and route to Unit 2 Spent Fuel Pool Critical Step (El 664, Refuel Floor, R6-U Line). | ||
-U Line). Standard: | SAT Standard: | ||
-SHV-067-0796 and route to Unit 2 Spent Fuel Pool (El 664 | UNSAT VERIFY hose connected from NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and route to Unit 2 Spent N/A Fuel Pool (El 664, Refuel Floor, R6-U Line). | ||
-U Line). | Note to Examiner: Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. Hoses are already connected, no tools required. | ||
Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. | |||
Hoses are already connected, no tools required. | |||
Location: Refuel Floor Elevation 664 ft, R U Line. | Location: Refuel Floor Elevation 664 ft, R U Line. | ||
Step 5: | Step 5: | ||
-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664 | [6] VERIFY hose connected from SOUTH HDR SPLY TO EMER Critical Step FUEL POOL MU, 1-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664, Refuel Floor, R6-U Line) | ||
-U Line) | SAT Standard: | ||
-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664 | UNSAT VERIFY hose connected from SOUTH HDR SPLY TO EMER N/A FUEL POOL MU, 1-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664, Refuel Floor, R6-U Line) 6 | ||
-U Line) | |||
Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. | Job Performance Measure (JPM) | ||
Hoses are already connected, no tools required. | STEP / STANDARD SAT / UNSAT Note to Examiner: Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. Hoses are already connected, no tools required. | ||
Location: Refuel Floor Elevation 664 ft, R U Line. | Location: Refuel Floor Elevation 664 ft, R U Line. | ||
Step 6: | Step 6: | ||
NORTH HDR SPLY TO EMER FUEL POOL MU, 1 | [7] VERIFY OPEN the following valves (El 664, Refuel Floor, R6 U Line): | ||
-SHV-067-0796. SOUTH HDR SPLY TO EMER FUEL POOL MU, 1 | * NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-Critical Step 0796. | ||
-SHV-067-0797. Standard: | SAT | ||
-SHV-067-0797 by demonstrating opening each valve | * SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797. | ||
UNSAT Standard: | |||
-SHV-067-0796 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1 | N/A Simulates opening NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797 by demonstrating opening each valve counter-clockwise. | ||
-SHV-067-0797 is OPEN | CUE: NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797 is OPEN Location: Refuel Floor Elevation 664 ft, R U Line. | ||
Step 7: | Step 7: | ||
Standard: | [8] VERIFY charged hoses on the Refuel Floor are not kinked. | ||
SAT Standard: UNSAT VERIFY charged hoses on the Refuel Floor are not kinked N/A Termination Criteria: NORTH and SOUTH Header are aligned then the JPM is complete. State another operator will perform the remaining steps. | |||
STOP TIME: | |||
7 | |||
Job Performance Measure (JPM) | |||
Job Performance Measure (JPM) | Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | ||
INITIAL CONDITIONS: | |||
INITIAL CONDITIONS: | You are an Operator on Unit 2. | ||
* The Reactor is in cold shutdown | |||
You are an Operator on Unit 2. The Reactor is in cold shutdown The Unit 2 Spent Fuel Pool water level is lowering. | * The Unit 2 Spent Fuel Pool water level is lowering. | ||
Fire Protection is available to assist INITIATING CUES | * Fire Protection is available to assist INITIATING CUES: | ||
: | |||
The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3]. | The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3]. | ||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START UP AND SYNCHRONIZE UNIT 3 PREFERRED MMG SET JPM NUMBER: | START UP AND SYNCHRONIZE UNIT 3 PREFERRED SITE: BFN JPM TITLE: | ||
307 REVISION: 6 | MMG SET JPM NUMBER: 307 REVISION: 6 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): S-57C-NO-04 K/A RATINGS: RO: 2.5 SRO: 2.9 262002 Uninterruptable Power Supply (A.C./D.C.) A1.02; Ability to predict and/or monitor changes in parameters associated with K/A No. &STATEMENT: | ||
SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): | operating the UNINTERRUPTABLE POWER SUPPLY (A.C./D.C.) controls including: Motor generator outputs RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 6 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by: | ||
S-57C-NO-04 | Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1) | ||
RO: | (See JPM Validation Checklist in NPG-SPP-17.8.2) | ||
262002 Uninterruptable Power Supply (A.C./D.C.) A1.02; Ability to predict and/or monitor changes in parameters associated with operating the UNINTERRUPTABLE POWER SUPPLY (A.C./D.C.) controls including: | Validated by: | ||
Motor generator outputs RELATED PRA INFORMATION: | Validator Date Approved by: | ||
Risk Significant SAFETY FUNCTION: | Site Training Management Date Approved by: | ||
6 | Site Training Program Owner Date 1 | ||
In-Plant | |||
ALTERNATE PATH (Y/N) | |||
Developed by: | |||
Developer | |||
-SPP-17.8.1) | |||
-SPP-17.8.2) | |||
Validator | |||
Site Training Management Date | |||
Job Performance Measure (JPM) | |||
OPERATOR: ________________________________ JPM Number: _307___ | |||
RO SRO DATE: _______ | |||
TASK STANDARD: Perform operations necessary to Start-up and synchronize Unit Preferred MMG Set Operator Fundamental evaluated: | |||
OF-1 Monitoring plant indications and conditions closely. | OF-1 Monitoring plant indications and conditions closely. | ||
OF-2 Controlling plant Evolutions Precisely PRA: NA REFERENCES/PROCEDURES NEEDED: | OF-2 Controlling plant Evolutions Precisely PRA: NA REFERENCES/PROCEDURES NEEDED: 0-OI-57C VALIDATIONTIME: 25 min PERFORMANCE TIME: | ||
0-OI-57C VALIDATIONTIME: 25 min | COMMENTS: | ||
COMMENTS: | Additional comment sheets attached? YES ___ NO ___ | ||
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ | |||
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.) | |||
SIGNATURE: ___________________________ DATE: __________ | |||
EXAMINER 2 | |||
Job Performance Measure (JPM) | |||
Revision Summary Rev Effective Pages Description No. Date Affected 1 10/26/94 ALL GENERAL REVISION 2 05/07/95 ALL GENERAL REVISION FORMAT, PROCEDURE REVISION, ADDED 3 10/15/97 ALL PLANT WORK EXPECTATIONS TOUCH STAAR, SAFETY, AND 3-WAY COMM. | |||
PROCEDURE REVISION, FORMAT 4 11/10/99 ALL DOCUMENT 5 10/03/01 ALL PROCEDURE REVISION 6 04/28/15 ALL UPDATE TO NEW FORMAT 3 | |||
-WAY COMM. 4 11/10/99 ALL | |||
Job Performance Measure (JPM) | |||
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
INITIAL CONDITIONS: | |||
You are an Operator on Unit 3. | |||
* The Reactor is in cold shutdown | |||
* The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1. | |||
* Maintenance has been completed on the Unit 3 Unit Preferred MMG Set. | |||
INITIATING CUES: | |||
The SM directs you to start up and synchronize the Unit 3 Unit Preferred MMG Set as directed by 0-OI-57C per section 5.5 step 5.5[16]. | |||
NOTE: PERFORMER WILL NEED GGMKA KEY. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
4 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
START TIME: | |||
[16] PLACE UNIT 3 MMG OPERATING MODE, 3 | STEP / STANDARD SAT / UNSAT Step 1: | ||
-HS-252-02AB in AUTO. Standard: | NOTE Steps 5.5[16] through 5.5[26] are performed from Battery Board Room 2 UNIT PFD Sync. & Speed Control Panel. Critical Step SAT | ||
-HS-252-02AB in AUTO. | [16] PLACE UNIT 3 MMG OPERATING MODE, 3-HS-252-02AB in AUTO. | ||
UNSAT Standard: | |||
N/A VERIFIED/SIMULATED PLACING the Unit 3 MMG SET OPERATING MODE 3-HS-252-02AB in AUTO. | |||
Cue: The Unit 3 MMG SET OPERATING MODE 3-HS-252-02AB is in AUTO position. | |||
-HS-252-02AB is in AUTO position. | |||
Step 2: | Step 2: | ||
Critical Step | Critical Step | ||
[17] PLACE UNIT 3 MMG LOCAL-REMOTE CONTROL, 3-XS-252-02A in REMOTE. | |||
SAT UNSAT N/A Cue: | SAT Standard: | ||
-REMOTE CONTROL 3 | UNSAT SIMULATED PLACING the Unit 3 MMG SET LOCAL-REMOTE N/A CONTROL 3-XS-252-02A in the REMOTE position. | ||
-HS-252-02A is in the REMOTE position. | Cue: The Unit 3 MMG SET LOCAL-REMOTE CONTROL 3-HS-252-02A is in the REMOTE position. | ||
Step 3: | Step 3: | ||
[18] PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH SS | [18] PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE Critical Step SYNC SWITCH SS-7, 3-HS-252-03/SS-7 in ON. | ||
-7, 3-HS-252-03/SS-7 in ON. Standard: | SAT Standard: | ||
-7, 3-HS-252-03/SS-7, in the ON position. | UNSAT SIMULATED PLACING UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 3-HS-252-03/SS-7, in the ON N/A position. | ||
5 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Cue: The Unit 3 PFD SYSTEM GENERATOR SOURCE SYNC SS-7, SWITCH 3-HS-252-003/SS-7 is in the ON position. | |||
Job Performance Measure (JPM) | Step 4: | ||
-7, SWITCH 3-HS-252-003/SS-7 is in the ON position. Step 4: | NOTE MMG voltage and hertz are read as INCOMING. | ||
Critical Step | Critical Step | ||
[19] MATCH Incoming to Running AC volts using UNIT 3 MMG VOLTAGE ADJUST, 3-HS-252-02CD. SAT Standard: UNSAT SIMULATED MANIPULATING UNIT 3 MMG VOLTAGE ADJUST, N/A 3-HS 252-02CD until cued that incoming and running AC volts are matched. | |||
Cue: INCOMING and RUNNING VOLTAGES are EQUAL at 122 Volts Step 5: | |||
[20] ADJUST MMG speed using UNIT 3 MMG FREQUENCY ADJUST, 3-HS-252-02CF to obtain a synchroscope slowly rotating in the SLOW Critical Step (counter-clockwise) direction (10 to 15 second rotation) as indicated on SYNCHROSCOPE, 0-SCP-252-000A/B. | |||
SAT Standard: | |||
UNSAT SIMULATED ADJUSTING UNIT 3 MMG FREQUENCY ADJUST N/A 3-HS-252-02CF speed control switch until cued that synchroscope indicator rotating in the counterclockwise direction at 10 to 15 seconds per revolution. | |||
Cue: State: The Initial Synchroscope indicator is standing still at the 5 oclock position. | |||
Note: If student raises frequency the state: Synchroscope indicator is rotating in the CLOCKWISE direction at 12 seconds per revolution. | |||
Note: If student lowers frequency the state: Synchroscope indicator is rotating in the COUNTERCLOCKWISE direction at 12 seconds per revolution. | |||
6 | |||
Job Performance Measure (JPM) | |||
STEP / STANDARD SAT / UNSAT Step 6: | |||
NOTES | |||
: 1) Section 5.5[21] should be performed expeditiously (within about 15 seconds) to minimize the time AC Systems are paralleled to prevent tripping the MMG set. Voltage and amps is expected to fluctuate while the AC systems are paralleled and the MMG set will trip if the AC systems are paralleled for approximately 30 seconds. | |||
Job Performance Measure (JPM) | |||
: 2) If breaker 1001 trips, it must be reset with reset push button on the respective Unit Battery Board, Panel 10. | : 2) If breaker 1001 trips, it must be reset with reset push button on the respective Unit Battery Board, Panel 10. | ||
CAUTIONS 1) Voltage Oscillations may occur during Bus Power Transfers. | CAUTIONS | ||
: 1) Voltage Oscillations may occur during Bus Power Transfers. | |||
These oscillations are caused when two Power Supplies having separate Voltage Regulators try to maintain voltage control. | These oscillations are caused when two Power Supplies having separate Voltage Regulators try to maintain voltage control. | ||
Therefore, the time the Power Supplies are paralleled should be minimized as follows:[PER 64835] | Therefore, the time the Power Supplies are paralleled should be minimized as follows:[PER 64835] | ||
When transferring Bus power supplies from one MMG to another MMG. | * When transferring Bus power supplies from one MMG to Critical Step another MMG. | ||
When transferring Bus power supplies from one MMG with the unit preferred transformer. (Unit 2 has a Voltage Regulator Transformer which makes voltage oscillations more susceptible.) | * When transferring Bus power supplies from one MMG with the SAT unit preferred transformer. (Unit 2 has a Voltage Regulator Transformer which makes voltage oscillations more UNSAT susceptible.) | ||
N/A | |||
: 2) Minimize the number of Bus power supply transfers and only transfer Bus power supplies when absolutely necessary. | : 2) Minimize the number of Bus power supply transfers and only transfer Bus power supplies when absolutely necessary. | ||
: 3) During the transfer of Bus power supplies the affiliated RPS circuit protectors 1(2)C1 and/or 1(2)C2 may trip. | : 3) During the transfer of Bus power supplies the affiliated RPS circuit protectors 1(2)C1 and/or 1(2)C2 may trip. | ||
Start of Critical Step(s) | Start of Critical Step(s) | ||
[21] WHEN SYNCHROSCOPE, 0-SCP-252-000A/B is 5 minutes prior to 12 o'clock, in the SLOW counter-clockwise direction, THEN PERFORM the following expeditiously: | |||
[21.1] CLOSE UNIT 3 BKR 1001, using 0-HS-280-003/1001. | |||
[21.2] ENSURE CLOSED UNIT 3 BKR 1001. | |||
7 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
STEP / STANDARD SAT / UNSAT Standard( step 6 continued): | |||
-HS-252-003/1001 in the CLOSE position. | When cued synchroscope indicator at 5 minutes prior to 12 o'clock, SIMULATED PLACING 3-BKR 1001, 0-HS-252-003/1001 in the CLOSE position. | ||
NOTE: IT WOULD ASSIST THE EXAMINEE IF THE EVALUATOR WOULD USE HIS FINGER TO DEMONSTRATE INDICATOR POSITION ON THE SYNCHROSCOPE AS THE READINGS ARE ENUNCIATED. | NOTE: IT WOULD ASSIST THE EXAMINEE IF THE EVALUATOR WOULD USE HIS FINGER TO DEMONSTRATE INDICATOR POSITION ON THE SYNCHROSCOPE AS THE READINGS ARE ENUNCIATED. | ||
CUE: THE SYNCHROSCOPE INDICATOR IS AT 30 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 15 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 5 MINUTES BEFORE THE 12 O'CLOCK POSITION | CUE: THE SYNCHROSCOPE INDICATOR IS AT 30 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 15 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 5 MINUTES BEFORE THE 12 O'CLOCK POSITION. | ||
CUE: [WHEN CLOSED] UNIT 3 BREAKER 1001 BREAKER POSITION INDICATING LAMP CHANGED FROM ILLUMINATED GREEN TO ILLUMINATED RED. | |||
Step 7: | |||
[21.3] OPEN the UNIT 3)BKR 1002, using 0 | [21.3] OPEN the UNIT 3)BKR 1002, using 0-HS-280-003/1002. Critical Step End of Critical Step(s) SAT Standard: UNSAT SIMULATED UNIT 3 BKR 1002, 0-HS-282-003/1002in the OPEN N/A position. | ||
-HS-280-003/1002. | CUE: UNIT 3 BKR 1002, 0-HS-282-003/1002 IS IN THE OPEN POSITION WITH RED LIGHT ILLUMINATED. | ||
NOTE: DO NOT ALLOW THE EXAMINEE TO OPERATE THE AMMETER SELECTOR SWITCH FOR THE FOLLOWING STEP. | |||
Standard: | |||
-HS-282-003/1002 IS IN THE OPEN POSITION WITH RED LIGHT ILLUMINATED. | |||
NOTE: | |||
Step 8: | Step 8: | ||
[22] CHECK generator is loaded by observing | SAT | ||
-II-252-02C/1AMR L2 rise, "N" should be approximately the difference of L1& L2 (UNIT 3 MMG GENERATOR amps, 3-HS-252-02CH positions 1, 2, & 3 are respective to L1, L2 & N). | [22] CHECK generator is loaded by observing UNIT 3 MMG GENERATOR amps, 3-II-252-02C/1AMR L2 rise, "N" should be UNSAT approximately the difference of L1& L2 (UNIT 3 MMG GENERATOR amps, 3-HS-252-02CH positions 1, 2, & 3 are respective to L1, L2 & N). | ||
N/A 8 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Cue: L1, L2 , N AMPS INDICATIONS HAVE RISEN and L1-L2 = N. Note: Selector Switch positions are labeled as follows: Position 1 is L1, position 2 is L2 and Position 3 is N. | STEP / STANDARD SAT / UNSAT Standard: | ||
Step 9: | CHECKED amp indicators L1 MINUS L2 approximately equals n. | ||
-HS-280-003/1003 | Cue: L1, L2, N AMPS INDICATIONS HAVE RISEN and L1-L2 = N. | ||
-HS-282-003/1003. | Note: Selector Switch positions are labeled as follows: Position 1 is L1, position 2 is L2 and Position 3 is N. | ||
Step 9: | |||
-HS-280-003/1003 Position Indicating Lamp changed from illuminated RED to illuminated GREEN. | [23] ENSURE OPEN UNIT 3 BKR 1003, 0-HS-280-003/1003 SAT Standard: UNSAT VERIFIED ILLUMINATED GREEN position indicating light above 0- N/A HS-282-003/1003. | ||
Step 10: | Cue: Unit 3 Breaker 1003 0-HS-280-003/1003 Position Indicating Lamp changed from illuminated RED to illuminated GREEN. | ||
BACKUP SOURCE TO BAT BD 1 BKR 1003, 1 | Step 10: | ||
-FUDS-280-001/1003 | [24] On Unit 2 Unit Preferred MMG Set Local Control Panel, ENSURE OPEN the following fused disconnect switches: | ||
-FUDS-280-003/1003 Standard: | * BACKUP SOURCE TO BAT BD 1 BKR 1003, 1-FUDS-280-001/1003 SAT | ||
-FUDS-280-003/1003 in the OPEN POSITION. | * BACKUP SOURCE TO BAT BD 3 BKR 1003, 3-FUDS-280-UNSAT 003/1003 N/A Standard: | ||
At Unit 2 Unit Preferred MMG Set Local Control Panel VERIFIED 1-FUDS-280-001/1003 AND 3-FUDS-280-003/1003 in the OPEN POSITION. | |||
Cue: 1-FUDS-280-001/1003 and 3-FUDS-280-003/1003 are in the OPEN position. | |||
9 | |||
Job Performance Measure (JPM) | Job Performance Measure (JPM) | ||
Standard: | STEP / STANDARD SAT / UNSAT Step 11: | ||
[25] On Unit 3 Unit Preferred MMG Set Local Control Panel, ENSURE the BACKUP SOURCE TO BAT BD 2 BKR 1003, SAT 2-FUDS-280-002/1003 fused disconnect switch is open: | |||
UNSAT Standard: | |||
N/A On Unit 3 Unit Preferred MMG Set Local Control Panel, VERIFIED 2-FUDS-280-002/1003 in the OPEN position. | |||
Cue: 2-FUDS-280-002/1003 is in the OPEN position. | |||
Step 12: | Step 12: | ||
[26] On Battery Board 2: | [26] On Battery Board 2: | ||
PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH SAT SS-7, 1-HS-252-03/SS-7 in OFF. | |||
PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH SS-7, 1-HS-252-03/SS-7 in OFF. Standard: | UNSAT Standard: | ||
-7, 1-HS-252-03/SS-7 in the OFF position. | N/A SIMULATED PLACING UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 1-HS-252-03/SS-7 in the OFF position. | ||
-7, 1-HS-252-03/SS-7 is in the OFF position. | Cue: UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 1-HS-252-03/SS-7 is in the OFF position. | ||
Step 13: | Step 13: | ||
[27] On Battery Board 2: | [27] On Battery Board 2: | ||
Critical Step DEPRESS UNIT 3 MMG AC MOTOR START, 3-HS-252-02AD to return SAT to Normal AC power from DC drive. | |||
DEPRESS UNIT 3 MMG AC MOTOR START, 3-HS-252-02AD to return to Normal AC power from DC drive. Standard: | UNSAT Standard: | ||
N/A SIMULATED DEPRESSING and RELEASING UNIT 3 MMG AC MOTOR START , 3-HS-252-02AD pushbutton. | |||
Cue: [The AC motor Breaker Position Indicating Lamp changed from illuminated GREEN to illuminated RED. State Another Operator will continue with procedure and this will end the task. | |||
State Another Operator will continue with procedure and this will end the task. | |||
STOP TIME: | STOP TIME: | ||
10 | |||
INITIAL CONDITIONS: | Job Performance Measure (JPM) | ||
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete. | |||
You are an Operator on Unit 3. The Reactor is in cold shutdown The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1. | INITIAL CONDITIONS: | ||
Maintenance has been completed on the Unit 3 Unit Preferred MMG Set. | You are an Operator on Unit 3. | ||
* The Reactor is in cold shutdown | |||
INITIATING CUES | * The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1. | ||
* Maintenance has been completed on the Unit 3 Unit Preferred MMG Set. | |||
]. NOTE: | INITIATING CUES: | ||
The SM directs you to start up and synchronize the Unit 3 Unit Preferred MMG Set as directed by 0-OI-57C per section 5.5 step 5.5[16]. | |||
NOTE: PERFORMER WILL NEED GGMKA KEY. | |||
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT! | ||
11}} |
Latest revision as of 06:01, 5 February 2020
ML16049A071 | |
Person / Time | |
---|---|
Site: | Browns Ferry ![]() |
Issue date: | 02/18/2016 |
From: | Division of Reactor Safety II |
To: | Tennessee Valley Authority |
References | |
Download: ML16049A071 (226) | |
Text
SITE: BFN JPM TITLE: RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: 80A U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: RO: 3.2 SRO: 3.3 201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL K/A No. &STATEMENT: CONTROL SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Rod Drift Alarm RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 1 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: __80A__
TASK STANDARD: Perform operations necessary to respond to a Control Rod Drift In per 2-AOI-85-5.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-85-5, 2-AOI-100-1 VALIDATIONTIME: 18 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/10 All Initial issue Incorrect task number; changed to U-085-AB-05:
1 09/01/15 1 Incorrect malfunction numbers; rd07r0231, rd07r2223 & rd07r3031; Corrected 3
SIMULATOR SETUP IC 28 Exam IC 280
- Run schedule file:NRC JPM A U2 -Control Rod Drift In
- Verify all triggers and overrides are correct
- Place the simulator in RUN to ensure stable conditions Console
- Start Rod Display on RWM Screen Operator Instructions
- Provide Initial Rod Data Sheet -PRLOG
- When prompted by the examiner, INSERT - Event 1 to Drift Control Rod 02-31 into the core
- When prompted by the examiner, INSERT - Event 2 to Drift Control Rod Multiple Control Rods into the core Malfunctions Description Event Severity Delay Initial set rd07r0231 Drifts rod 02-31 into 1 NA 35 sec NA core rd07r2223 Drifts rod 22-23 into 2 NA 10 sec NA core rd07r3031 Drifts rod 30-31 into 2 NA 25 sec NA core rd07r4635 Drifts rod 46-35 into 2 NA 20 sec NA core rd07r2619 Drifts rod 26-19 into 2 NA 30 sec NA core rd07r3027 Drifts rod 30-27 into 2 NA 18 sec NA core rd07r5423 Drifts rod 54-23 into 2 NA 23 sec NA core rd07r2255 Drifts rod 22-55 into 2 NA 28 sec NA core 4
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): NRC JPM A U2 -Control Rod Drift In 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is at 100% power INITIATING CUES:
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods.
6
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
NOTE
- 1) Problem details of any control rod issues observed during the performance of this surveillance must be recorded on Attachment 3 for further review and possible corrective maintenance. Slow/fast rod movements or settle times should be noted in the remarks section.
- 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1.
CAUTIONS
- 1) Any mispositioned control rod events will be dispositioned by following the direction contained within 2-AOI-85-7.
- 2) If a control rod moves unexpectedly one notch beyond its intended Critical Step position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. SAT
N/A 7.3 Exercising a Partially Withdrawn Control Rod
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40.
[2] OBSERVE the following for selected control rod:
- CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED.
- CHECK white light on the Full Core Display is ILLUMINATED.
- CHECK Rod Out Permit light is ILLUMINATED.
Standard:
Selects a withdrawn control rod Note to Examiner: May select any partially withdrawn control rod in any order 7
STEP / STANDARD SAT / UNSAT Step 2:
[3] INSERT control rod one notch by performing the following:
Critical Step
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN andRELEASE. SAT
[3.2] OBSERVE control rod settles into the desired position UNSAT andROD SETTLE light extinguishes.
N/A Standard:
Inserts withdrawn control rod one notch Step 3:
[4] WITHDRAW selected control rod one notch by performing the following: Critical Step
[4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD OUT NOTCHand RELEASE. SAT
[4.2] OBSERVE control rod settles into the desired position and UNSAT ROD SETTLE light extinguishes.
N/A Standard:
Withdraws withdrawn control rod one notch Step 4:
[5] DOCUMENT completion of control rod test as follows:
[5.1] PERFORMER
- INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the SAT control rodjust exercised to document proper movement and CRD latching. UNSAT
[5.2] Concurrent Verifier (CV) N/A
- ENSURE rod inserted and returned to its original position.
- INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised.
8
STEP / STANDARD SAT / UNSAT Standard:
Initials Attachment 1 for exercised control rod and continues to exercise rods.
Note to Examiner:
- Perform above actions for @ least two control rods.
- When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #1 for Control Rod 02-31 Drift In Note to Simulator Booth Operator:
- When directed by examiner insert trigger #1 for 02-31 Control Rod Drift In.
Step 5:
Performer recognizes control rod 02-31 drift in and responds per 2-AOI-85-5.
[2] IF a Control Rod is moving from its intended position without Critical Step operator actions, THEN INSERT the Control Rod to position 00 using CONTINUOUS IN. (Otherwise N/A) SAT
[3] IF a Control Rod Block occurs during rod insertion due to Rod UNSAT Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above.
(Otherwise N/A) N/A Standard:
Responds per 2-AOI-85-5 and inserts control rod 02-31 to full in position as indicated by position 00 indication.
CUE: When report to US, state Respond per 2-AOI-85-5, Control Rod Drift In.
Step 6:
[4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod SAT pattern.
UNSAT Standard:
Candidate notifies Reactor Engineer to Evaluate Core N/A Thermal limits and Preconditioning Limits for the current Control Rod Pattern Cue: Understand Reactor Engineering notified to evaluate Core Thermal andPreconditioning Limits 9
STEP / STANDARD SAT / UNSAT Step 7:
[5] IF another Control Rod Drift occurs before Reactor Engineering completes the evaluation,
[6] CHECK Thermal Limits on ICS (RUNMON). UNSAT Note to NRC Examiner: Step [6] performed by Reactor N/A Engineering.
Standard:
Reviews step and asks for guidance from US or RE CUE: As Shift Manager, state RE has evaluated Core Thermal and Preconditioning Limits and has determined that the Control Rod Exercise may continue and that any other Control Rod Drift will be considered the first.
Student will continue with Control Rod Exercise.
Step 8:
7.3 Exercising a Partially Withdrawn Control Rod
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. Critical Step
[2] OBSERVE the following for selected control rod: SAT
- CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. UNSAT
- CHECK white light on the Full Core Display is ILLUMINATED.
- CHECK Rod Out Permit light is ILLUMINATED. N/A Standard:
Selects a withdrawn control rod 10
STEP / STANDARD SAT / UNSAT Step 9:
[3] INSERT control rod one notch by performing the following:
Critical Step
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN SAT andRELEASE.
UNSAT
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes.
N/A Standard:
Inserts withdrawn control rod one notch Step 10:
[4] WITHDRAW selected control rod one notch by performing the Critical Step following:
[4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD SAT OUT NOTCHand RELEASE.
UNSAT
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes.
N/A Standard:
Withdraws withdrawn control rod one notch Note to Examiner:
When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #2 for Multiple Control Rods Drifting In Step 11:
Multiple Control Rods Drifting In Critical Step Standard:
Recognizes Multiple Control Rods Drift into the Core and Manually SAT Scrams the Reactor per 2-AOI-85-5.
UNSAT
- Depresses both SCRAM Pushbuttons
- Places mode switch in shutdown N/A
- Verifies All Rods in 11
STEP / STANDARD SAT / UNSAT Step 11 continued:
- Performs a Scram Announcement Critical Step o Rx Mode Switch Position: Shutdown o Rod Position: All Full In SAT o Reactor Water Level ____ & Trend ___
o Reactor Pressure ____ & Trend ___ UNSAT o MSIV Position: OPEN o Rx Power: <5% N/A Termination Criteria: REPEAT BACK SCRAM REPORT THEN STATE, THIS COMPLETES THE JPM. THAT WILL BE ALL FOR NOW, ANOTHER OPERATOR WILL CONTINUE IN 2-AOI-100-1.
STOP TIME:
12
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is at 100% power INITIATING CUES:
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods.
13
SITE: BFN JPM TITLE: RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: 80A U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: RO: 3.2 SRO: 3.3 201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL CONTROL SYSTEM ; and (b) based on K/A No. &STATEMENT:
those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations:
Rod Drift Alarm RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 1 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _80A U3_
TASK STANDARD: Perform operations necessary to respond to a Control Rod Drift In per 3-AOI-85-5.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: 3-AOI-85-5, 3-AOI-100-1 VALIDATIONTIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/10 All Initial issue Incorrect task number; changed to U-085-AB-05:
1 05/11/15 1 Incorrect malfunction numbers; rd07r0231, rd07r2223 & rd07r3031; Corrected 3
SIMULATOR SETUP IC 28 Exam IC 280
- Run schedule file: NRC JPM A U3 -Control Rod Drift In
- Verify all triggers and overrides are correct
- Place the simulator in RUN to ensure stable conditions Console Operator
- Start Rod Display on RWM Screen Instructions
- Provide Initial Rod Data Sheet -PRLOG
- When prompted by the examiner, INSERT - Event 1 to Drift Control Rod 02-31 into the core
- When prompted by the examiner, INSERT - Event 2 to Drift Control Rod Multiple Control Rods into the core Malfunctions Description Event Severity Delay Initial set rd07r0231 Drifts rod 02-31 into 1 NA 35 sec NA core rd07r2223 Drifts rod 22-23 into 2 NA 10 sec NA core rd07r3031 Drifts rod 30-31 into 2 NA 25 sec NA core rd07r4635 Drifts rod 46-35 into 2 NA 20 sec NA core rd07r2619 Drifts rod 26-19 into 2 NA 30 sec NA core rd07r3027 Drifts rod 30-27 into 2 NA 18 sec NA core rd07r5423 Drifts rod 54-23 into 2 NA 23 sec NA core rd07r2255 Drifts rod 22-55 into 2 NA 28 sec NA core 4
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): NRC JPM A U3 -Control Rod Drift In 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is at 100% power INITIATING CUES:
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods.
6
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
NOTE
- 1) Problem details of any control rod issues observed during the performance of this surveillance must be recorded on Attachment 3 for further review and possible corrective maintenance. Slow/fast rod movements or settle times should be noted in the remarks section.
- 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1.
CAUTIONS
- 3) Any mispositioned control rod events will be dispositioned by following the direction contained within 3-AOI-85-7.
- 4) If a control rod moves unexpectedly one notch beyond its intended Critical Step position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. SAT
N/A 7.3 Exercising a Partially Withdrawn Control Rod
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 3-XS-85-40.
[2] OBSERVE the following for selected control rod:
- CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED.
- CHECK white light on the Full Core Display is ILLUMINATED.
- CHECK Rod Out Permit light is ILLUMINATED.
Standard:
Selects a withdrawn control rod Note to Examiner: May select any partially withdrawn control rod in any order 7
STEP / STANDARD SAT / UNSAT Step 2:
[3] INSERT control rod one notch by performing the following:
Critical Step
[3.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD IN andRELEASE. SAT
[3.2] OBSERVE control rod settles into the desired position UNSAT andROD SETTLE light extinguishes.
N/A Standard:
Inserts withdrawn control rod one notch Step 3:
[4] WITHDRAW selected control rod one notch by performing the following: Critical Step
[4.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD OUT NOTCHand RELEASE. SAT
[4.2] OBSERVE control rod settles into the desired position and UNSAT ROD SETTLE light extinguishes.
N/A Standard:
Withdraws withdrawn control rod one notch Step 4:
[5] DOCUMENT completion of control rod test as follows:
[5.1] PERFORMER
- INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the SAT control rodjust exercised to document proper movement and CRD latching. UNSAT
[5.2] Concurrent Verifier (CV) N/A
- ENSURE rod inserted and returned to its original position.
- INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised.
8
STEP / STANDARD SAT / UNSAT Standard:
Initials Attachment 1 for exercised control rod and continues to exercise rods.
Note to Examiner:
- Perform above actions for @ least two control rods.
- When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #1 for Control Rod 02-31 Drift In Note to Simulator Booth Operator:
- When directed by examiner insert trigger #1 for 02-31 Control Rod Drift In.
Step 5:
Performer recognizes control rod 02-31 drift in and responds per 3-AOI-85-5.
[2] IF a Control Rod is moving from its intended position without Critical Step operator actions, THEN INSERT the Control Rod to position 00 using CONTINUOUS IN. (Otherwise N/A) SAT
[3] IF a Control Rod Block occurs during rod insertion due to Rod UNSAT Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above.
(Otherwise N/A) N/A Standard:
Responds per 3-AOI-85-5 and inserts control rod 02-31 to full in position as indicated by position 00 indication.
CUE: When report to US, state Respond per 3-AOI-85-5, Control Rod Drift In.
Step 6:
[4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod SAT pattern.
UNSAT Standard:
Candidate notifies Reactor Engineer to Evaluate Core N/A Thermal limits and Preconditioning Limits for the current Control Rod Pattern Cue: Understand Reactor Engineering notified to evaluate Core Thermal andPreconditioning Limits 9
STEP / STANDARD SAT / UNSAT Step 7:
[5] IF another Control Rod Drift occurs before Reactor Engineering completes the evaluation,
[6] CHECK Thermal Limits on ICS (RUNMON). UNSAT Note to NRC Examiner: Step [6] performed by Reactor N/A Engineering.
Standard:
Reviews step and asks for guidance from US or RE CUE: As Shift Manager, state RE has evaluated Core Thermal and Preconditioning Limits and has determined that the Control Rod Exercise may continue and that any other Control Rod Drift will be considered the first.
Student will continue with Control Rod Exercise.
Step 8:
7.3 Exercising a Partially Withdrawn Control Rod
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. Critical Step
[2] OBSERVE the following for selected control rod: SAT
- CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. UNSAT
- CHECK white light on the Full Core Display is ILLUMINATED.
- CHECK Rod Out Permit light is ILLUMINATED. N/A Standard:
Selects a withdrawn control rod 10
STEP / STANDARD SAT / UNSAT Step 9:
[3] INSERT control rod one notch by performing the following:
Critical Step
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN SAT andRELEASE.
UNSAT
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes.
N/A Standard:
Inserts withdrawn control rod one notch Step 10:
[4] WITHDRAW selected control rod one notch by performing the Critical Step following:
[4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD SAT OUT NOTCHand RELEASE.
UNSAT
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes.
N/A Standard:
Withdraws withdrawn control rod one notch Note to Examiner:
When satisfied with the number of rod manipulations direct Simulator BoothOperator to insert trigger #2 for Multiple Control Rods Drifting In Step 11:
Multiple Control Rods Drifting In Standard: Critical Step Recognizes Multiple Control Rods Drift into the Core and Manually Scrams the Reactor per 3-AOI-85-5. SAT
- Depresses both SCRAM Pushbuttons UNSAT
- Places mode switch in shutdown
- Verifies All Rods in N/A 11
STEP / STANDARD SAT / UNSAT Step 11 continued:
Critical Step
- Performs a Scram Announcement o Rx Mode Switch Position: Shutdown SAT o Rod Position: All Full In o Reactor Water Level ____ & Trend ___ UNSAT o Reactor Pressure ____ & Trend ___
o MSIV Position: OPEN N/A o Rx Power: <5%
Termination Criteria: repeat back scram report then state, this completes the JPM. That will be all for now, another operator will continue in 2-AOI-100-1 STOP TIME:
12
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is at 100% power INITIATING CUES:
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods.
13
SITE: BFN JPM TITLE: EHC Auto Cooldown JPM NUMBER: 276 U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-NO-32 Perform Reactor Cooldown TASK NUMBER / TASK TITLE(S): U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: RO: 3.9 SRO: 3.9 239001Main and Reheat Steam System: A4.09 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 4 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _276 U2 RO SRO DATE: _______
TASK STANDARD: Perform operations necessary to initiate an Auto Cooldown with Turbine Bypass Valves.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-OI-47 VALIDATIONTIME: 4 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 06/19/12 All Initial issue 1 07/22/15 All General revision & re-format 3
SIMULATOR SETUP IC 40 Exam IC 281
Console Operator Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): None 4
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves.
INITIATING CUES:
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 2-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6].
5
START TIME:
STEP / STANDARD SAT / UNSAT Step 1: SAT
[6] VERIFY EHC is in Pressure Control using 2-HS-47-204. UNSAT N/A Standard:
Observes light on for EHC Pressure Control on 2-HS-47-204.
Step 2:
[7] On the EHC Work Station on Panel 9-7:
[7.1] SELECT Main Menu from the toolbar at bottom of the screen. Critical Step
[7.2] SELECT Log In on Display Screen and ENTER OPS SAT for name and OPS for Password.
UNSAT
[7.3] SELECT Auto Cooldown from list of function on the screen. N/A Standard:
Candidate logs into EHC workstation and selects Auto Cooldown from the list of functions on the screen.
Step 3:
[8] On the Auto Cooldown Display Screen CHECK the following are displayed.
- Turbine Tripped or All Valves Closed - indicates Reset.
- Rx Press Ctrl - indicates Reset. UNSAT Standard: N/A
- Candidate checks the Turbine Tripped or All Valves Closed
-indicates Reset.
- Candidate checks Rx Press Ctrl - indicates Reset.
6
STEP / STANDARD SAT / UNSAT Step 4:
[9] On the Auto Cooldown Screen SET the desired Final Pressure for cooldown as follows:
[9.1] SELECT the block above the FINAL PRESSURE Critical Step TARGET.
[9.2] ENTER the desired pressure using the Display Screen or Key Board.
UNSAT
[9.3] WHEN desired Pressure is entered SELECT OK N/A Standard:
Candidate sets the desired final target pressure of 20psig (given in initial conditions).
Step 5:
[10] WHEN Cooldown is ready to commence, THEN
[10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary)
Critical Step
[10.2] DEPRESS the START button on the Auto Cooldown Display Screen. SAT
[11] WHEN Caution Are You Sure You Want to Initiate Auto UNSAT Cooldown? appears N/A SELECT Yes Screen Button to start the cooldown.
Standard:
Candidate depresses START and acknowledges YES to commence auto cooldown.
7
STEP / STANDARD SAT / UNSAT Step 6:
[12] CHECK the following:
- EHC PRESSURE SETPOINT, 2-PI-47-162, is lowering.
- EHC AUTO COOLDOWN displays IN PROGRESS SAT Standard: UNSAT Candidate monitors EHC pressure and the auto cooldown is IN N/A PROGRESS.
Cue: The Unit Supervisor directs you to adjust the Final Pressure Target to 100 psig.
Step 7:
[13] IF it is desired to change the Final Pressure Target, THEN On the Auto Cooldown Screen.
[13.1] SELECT the block above the FINAL PRESSURE TARGET Critical Step
[13.2] ENTER the desired pressure using the Display SAT Screen or Key Board.
UNSAT
[13.3] WHEN desired Pressure is entered SELECT OK N/A Standard:
Candidate adjusts FINAL PRESSURE TARGET to 100 psig and recommences the auto cooldown.
Evaluator Cue: Another operator will continue to monitor the cooldown. This completes your task.
STOP TIME:
8
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves.
INITIATING CUES:
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 2-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6].
9
SITE: BFN JPM TITLE: EHC Auto Cooldown JPM NUMBER: 276 U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-NO-32 Perform Reactor Cooldown TASK NUMBER / TASK TITLE(S): U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: RO: 3.9 SRO: 3.9 239001Main and Reheat Steam System: A4.09 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 4 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _276 U3_
TASK STANDARD: Perform operations necessary to initiate an Auto Cooldown with Turbine Bypass Valves.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 3-OI-47 VALIDATIONTIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 06/19/12 All Initial issue 1 07/22/15 All General revision & re-format 3
SIMULATOR SETUP IC 40 Exam IC 281
Console Operator Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): None 4
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves.
INITIATING CUES:
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 3-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6].
5
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
[6] VERIFY EHC is in Pressure Control using 3-HS-47-204. SAT UNSAT Standard:
N/A Observes light on for EHC Pressure Control on 3-HS-47-204.
Step 2:
[7] On the EHC Work Station on Panel 9-7:
[7.1] SELECT Main Menu from the toolbar at bottom of the screen. Critical Step
[7.2] SELECT Log In on Display Screen and ENTER OPS SAT for name and OPS for Password.
UNSAT
[7.3] SELECT Auto Cooldown from list of function on the screen. N/A Standard:
Candidate logs into EHC workstation and selects Auto Cooldown from the list of functions on the screen.
Step 3:
[8] On the Auto Cooldown Display Screen CHECK the following are displayed.
- Turbine Tripped or All Valves Closed - indicates Reset.
- Rx Press Ctrl - indicates Reset. UNSAT Standard: N/A
- Candidate checks the Turbine Tripped or All Valves Closed
-indicates Reset.
- Candidate checks Rx Press Ctrl - indicates Reset.
6
Step 4:
[9] On the Auto Cooldown Screen SET the desired Final Pressure for cooldown as follows:
[9.1] SELECT the block above the FINAL PRESSURE Critical Step TARGET.
[9.2] ENTER the desired pressure using the Display Screen or Key Board.
UNSAT
[9.3] WHEN desired Pressure is entered SELECT OK N/A Standard:
Candidate sets the desired final target pressure of 20psig (given in initial conditions).
Step 5:
[10] WHEN Cooldown is ready to commence, THEN
[10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary)
Critical Step
[10.2] DEPRESS the START button on the Auto Cooldown Display Screen. SAT
[11] WHEN Caution Are You Sure You Want to Initiate Auto UNSAT Cooldown? appears N/A SELECT Yes Screen Button to start the cooldown.
Standard:
Candidate depresses START and acknowledges YES to commence auto cooldown.
7
Step 6:
[12] CHECK the following:
- EHC PRESSURE SETPOINT, 3-PI-47-162, is lowering.
- EHC AUTO COOLDOWN displays IN PROGRESS SAT Standard: UNSAT Candidate monitors EHC pressure and the auto cooldown is IN N/A PROGRESS.
Cue: The Unit Supervisor directs you to adjust the Final Pressure Target to 100 psig.
Step 7:
[13] IF it is desired to change the Final Pressure Target, THEN On the Auto Cooldown Screen.
[13.1] SELECT the block above the FINAL PRESSURE TARGET Critical Step
[13.2] ENTER the desired pressure using the Display SAT Screen or Key Board.
UNSAT
[13.3] WHEN desired Pressure is entered SELECT OK N/A Standard:
Candidate adjusts FINAL PRESSURE TARGET to 100 psig and recommences the auto cooldown.
Evaluator Cue: Another operator will continue to monitor the cooldown. This completes your task.
STOP TIME:
8
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves.
INITIATING CUES:
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 3-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6].
9
LOSS OF REFERENCE APRM TO ROD BLOCK SITE: BFN JPM TITLE:
MONITOR JPM NUMBER: 672A U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-085-AL-03 RESPOND TO CONTROL ROD TASK NUMBER / TASK TITLE(S):
WITHDRAWL BLOCK K/A RATINGS: RO: 3.1 SRO: 3.3 215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures K/A No. &STATEMENT:
to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR-3,4,5 RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 7 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _672A U2_
TASK STANDARD: Perform operations necessary to bypass an APRM Channel and clear a Control Rod Block from Rod Block Monitoring System.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-OI-85, 2-OI-92B, 2-ARP-9-5A, 2-SR-3.1.3.5(A)
VALIDATIONTIME: 16 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 3
SIMULATOR SETUP IC 39 Exam IC 282
- Reset to IC-39 to ~ 30% Reactor Power
- Open Event File: NRC JPM C U2 -RBM APRM Fail Downscale.evt Malfunctions Description Event Severity Delay Initial set NM07L3233C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-33-C NM07L4025B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-25-B NM07L4033D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-33-D NM07L0817B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-17-B NM07L4017B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-17-B NM07L4041D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-41-D NM07L4049B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-49-B NM07L4057B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-57-B NM07L4817C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-17-C NM07L4825C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-25-C NM07L4833A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-33-A NM07L4841A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-41-A NM07L4849C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-49-C NM07L0825B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-25-B 4
NM07L0833D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-33-D NM07L0841D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-41-D NM07L0849B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-49-B NM07L2409B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-09-B NM07L2417D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-17-D NM07L2425D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-25-D NM07L2433B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-33-B NM07L2449D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-49-D NM07L2457D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-57-D NM07L1617C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-17-C NM07L1625C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-25-C NM07L1633A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-33-A NM07L1641A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-41-A NM07L1649C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-49-C NM07L1657C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-57-C NM07L1609A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-09-A NM07L3209C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-09-C NM07L3217A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-17-A NM07L3225A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-25-A NM07L3249A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-49-A NM07L3257A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-57-A NM07L4009D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-09-D NM07L4809A LPRM AMPLIFIER 15 0 N/A N/A 5
FAILURE 48-09-A NM07L5617D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-17-D NM07L5633B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-33-B NM07L5641B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-41-B NM07L3241C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-41-C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLO4631LGREENT(1) Control Rod 46-31 15 0 N/A N/A GREEN INDICATION Schedule File(s):
Event File: NRC JPM C U2 -RBM APRM Fail Downscale.evt; <TRIGGER id="15" description="APRM Ch 2 Fail Downscale">ZLO4631LGREENT(1) == 0</TRIGGER>
Schedule File: NRC JPM C U2 -RBM APRM Fail Downscale.sch 6
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is at 30% power
- Startup Sequence Control Rod Movement Data Sheet 2-SR-3.1.3.5(A) completed through group 57.
- No Control Rods are Fast Notching INITIATING CUES:
The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14-31.
7
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
Step 2:
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT
- THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A)
N/A Standard:
Determines that step in N/A Step 3:
[3] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED 8
STEP / STANDARD SAT / UNSAT Step 4:
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 5:
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 6:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
9
STEP / STANDARD SAT / UNSAT Step 7:
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT
- THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A)
N/A Standard:
Determines that step in N/A Step 8:
[3] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 9:
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing 10
STEP / STANDARD SAT / UNSAT Step 10:
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 11:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
Step 12:
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT
- THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A)
N/A Standard:
Determines that step in N/A 11
STEP / STANDARD SAT / UNSAT Step 13:
[3] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 14:
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 15:
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 12
STEP / STANDARD SAT / UNSAT Note to Examiner: This begins the Alternate Path section of JPM Simulator Booth Operator: Insert Event Trigger #1 to fail APRM 2 Downscale.
Step 16:
APRM Sensor/Trip Point:
DOWNSCALE/
APRM Downscale: <= 5%
OPRM INOP OPRM Inop: Less than 23 operable cells 4
Sensor Location:
Control Room Panel 2-9-14.
Probable Cause:
A. Unbypassed APRM channel at or below sensor set point.
B. SI or SR in progress.
C. Unit shutdown (Mode 3 or 4). Critical Step D. Failed sensor.
SAT Automatic Action: UNSAT A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only)
N/A Operator Action:
A. DETERMINE which APRM/OPRM channel is downscale/inop.
B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 2-OI-92B.
13
STEP / STANDARD SAT / UNSAT Step 16(continued)
CONTROL ROD Sensor/Trip Point:
WITHDRAWAL Relays: 3A-K1 Nuclear Instrumentation BLOCK 3A-K2 Refuel Equipment in Use High Level in Scram Discharge 7 Volume Scram Discharge Volume High Water Level Bypass Rx Mode Switch in SHUTDOWN PRNM (ANY APRM OPRM or RBM)
Sensor Location:
Panel 2-9-28 Elevation 593' Aux Instr Room Probable Cause:
A. One or more sensors at or above set point.
B. Malfunction of sensor.
C. Control rod drop accident Automatic Action:
Rod withdrawal block Operator Action:
A. DETERMINE initiating condition from corresponding rod withdrawal block alarm(s) and REFER TO operator action for alarm(s).
Standard:
Reference 2-ARP-9-5A and identifies APRM Ch 2 is down scale and proceeds to bypass APRM Ch 2 per 2-OI-92B CUE: Respond as stated in Alarm Response Instruction and Bypass APRM Ch 2 per 3-OI-92B.
14
STEP / STANDARD SAT / UNSAT Step 17:
NOTES
- 1) Only one APRM/OPRM in each trip system can be bypassed at a time.
- 2) All operations are performed on Panel 2-9-5 unless specifically stated otherwise.
- 3) In order to prevent inadvertent rod withdrawal block or Reactor scram while operating APRM BYPASS selector switch, Verify that the BLUE BYPASSED lights on Panel 9-14 Voters are extinguished prior to selecting any other channel to be bypassed. After bypassing a channel, the applicable BLUE BYPASSED status lights on Panel 9-14 Voters are required to be illuminated prior to testing, operating, or working on that channel. SAT UNSAT 6.1 Bypassing APRM/OPRM Channel N/A CAUTION
[QA/C] SPP-10.4 requires approval of the Plant Manager or his designee prior to any planned operation with APRMs bypassed unless bypassing is specifically allowed within approved procedures.
[ISE-HPS-92-RO1]
[1] REVIEW all precautions and limitations. REFER TO Section 3.0.
Standard:
Demonstrates reviewing precautions and limitations section 3.0.
Step 18:
Critical Step
[2] PLACE APRM BYPASS, 2-HS-92-7B/S3, to desired channel to be bypassed. SAT Standard: UNSAT PLACE APRM BYPASS, 2-HS-92-7B/S3, to APRM CH 2 N/A 15
STEP / STANDARD SAT / UNSAT Step 19:
[3] CHECK BLUE BYPASSED lights illuminated on Panel 2-9-14 Voters. SAT Standard: UNSAT Observes BLUE BYPASS light illuminated on Panel 2-9-14 for N/A APRM CH 2.
Step 20:
[4] VERIFY white bypass light on Panel 2-9-5 is illuminated. SAT Standard: UNSAT Observes WHITE BYPASS light illuminated on Panel 2-9-5. N/A Note to Examiner: If needed, cue student to proceed with actions required to continue rod movements. Student may continue at step 21 or 24.
Step 21:
6.6.2 Actions Required During and Following Control Rod Withdrawal (continued)
[6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN SAT PERFORM the following at the Unit Supervisors discretion to UNSAT REINITIALIZE the RBM:
N/A
[6.1] PLACE CRD POWER, 2-HS-85-46 in the OFF position to deselect the Control Rod.
Standard:
CRD POWER, 2-HS-85-46 in the OFF position.
16
STEP / STANDARD SAT / UNSAT Step 22:
[6.2] PLACE CRD POWER, 2-HS-85-46, in the ON position.
UNSAT Standard:
N/A PLACED CRD POWER, 2-HS-85-46, in the ON position.
Step 23:
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and SAT PERFORM applicable section for Control Rod withdrawal.
UNSAT Standard:
N/A Continues with Control Rod Movement CUE: Proceed with Control Rod Movement.
Step 24:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
17
STEP / STANDARD SAT / UNSAT Step 25:
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT
- THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A)
N/A Standard:
Determines that step in N/A Step 26:
[3] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 27:
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing 18
STEP / STANDARD SAT / UNSAT Step 28:
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Termination Criteria: When Control Rod is at position 04, state End of Task STOP TIME:
19
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is at 30% power
- Startup Sequence Control Rod Movement Data Sheet 2-SR-3.1.3.5(A) completed through group 57.
INITIATING CUES:
The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14-31.
20
LOSS OF REFERENCE APRM TO ROD BLOCK SITE: BFN JPM TITLE:
MONITOR JPM NUMBER: 672A U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-085-AL-03 RESPOND TO CONTROL ROD TASK NUMBER / TASK TITLE(S):
WITHDRAWL BLOCK K/A RATINGS: RO: 3.1 SRO: 3.3 215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures K/A No. &STATEMENT:
to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR-3,4,5 RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 7 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _672A U3_
TASK STANDARD: Perform operations necessary to bypass an APRM Channel and clear a Control Rod Block from Rod Block Monitoring System.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 3-OI-85, 3-OI-92B, 3-ARP-9-5A, 3-SR-3.1.3.5(A)
VALIDATIONTIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 04/30/15 All Initial issue 3
SIMULATOR SETUP IC 39 Exam IC 282
- Reset IC-39to ~ 30% Reactor Power
- Open Event File: NRC JPM C U3 -RBM APRM Fail Downscale.evt Malfunctions Description Event Severity Delay Initial set NM07L3233C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-33-C NM07L4025B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-25-B NM07L4033D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-33-D NM07L0817B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-17-B NM07L4017B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-17-B NM07L4041D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-41-D NM07L4049B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-49-B NM07L4057B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-57-B NM07L4817C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-17-C NM07L4825C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-25-C NM07L4833A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-33-A NM07L4841A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-41-A NM07L4849C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-49-C NM07L0825B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-25-B 4
NM07L0833D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-33-D NM07L0841D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-41-D NM07L0849B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-49-B NM07L2409B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-09-B NM07L2417D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-17-D NM07L2425D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-25-D NM07L2433B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-33-B NM07L2449D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-49-D NM07L2457D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-57-D NM07L1617C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-17-C NM07L1625C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-25-C NM07L1633A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-33-A NM07L1641A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-41-A NM07L1649C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-49-C NM07L1657C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-57-C NM07L1609A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-09-A NM07L3209C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-09-C NM07L3217A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-17-A NM07L3225A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-25-A NM07L3249A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-49-A NM07L3257A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-57-A NM07L4009D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-09-D NM07L4809A LPRM AMPLIFIER 15 0 N/A N/A 5
FAILURE 48-09-A NM07L5617D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-17-D NM07L5633B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-33-B NM07L5641B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-41-B NM07L3241C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-41-C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLO4631LGREENT(1) Control Rod 46-31 15 0 N/A N/A GREEN INDICATION Schedule File(s):
Event File: NRC JPM C U3 -RBM APRM Fail Downscale.evt; <TRIGGER id="15" description="APRM Ch 2 Fail Downscale">ZLO4631LGREENT(1) == 0</TRIGGER>
Schedule File: NRC JPM C U3 -RBM APRM Fail Downscale.sch 6
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is at 30% power
- Startup Sequence Control Rod Movement Data Sheet 3-SR-3.1.3.5(A) completed through group 58.
INITIATING CUES:
The US has directed you to raise Reactor Power to 40% per 3-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 59; Control Rod 22-39.
7
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
Step 2:
[2] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 3:
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing 8
STEP / STANDARD SAT / UNSAT Step 4:
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 5:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
Step 6:
[2] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED 9
STEP / STANDARD SAT / UNSAT Step 7:
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 8:
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 9:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
10
STEP / STANDARD SAT / UNSAT Step 10:
[2] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 11:
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 12:
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 11
STEP / STANDARD SAT / UNSAT Note to Examiner: This begins the Alternate Path section of JPM Simulator Booth Operator: Insert Event Trigger #1 to fail APRM 2 Downscale.
Step 13:
APRM Sensor/Trip Point:
DOWNSCALE/
APRM Downscale: <= 5%
OPRM INOP OPRM Inop: Less than 23 operable cells 4
Sensor Location:
Control Room Panel 3-9-14.
Probable Cause:
A. Unbypassed APRM channel at or below sensor set point.
B. SI or SR in progress.
C. Unit shutdown (Mode 3 or 4). Critical Step D. Failed sensor.
SAT Automatic Action: UNSAT A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only)
N/A Operator Action:
A. DETERMINE which APRM/OPRM channel is downscale/inop.
B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 3-OI-92B.
12
STEP / STANDARD SAT / UNSAT Step 13(continued)
CONTROL ROD Sensor/Trip Point:
WITHDRAWAL Relays:3A-K1 Nuclear Instrumentation BLOCK 7 3A-K2 Refuel Equipment in Use High Level in Scram Discharge Volume Scram Discharge Volume High Water Level Bypass Rx Mode Switch in SHUTDOWN PRNM (ANY APRM OPRM or RBM)
Sensor Location:
Panel 3-9-28 Elevation 593' Aux Instr Room Probable Cause:
A. One or more sensors at or above set point.
B. Malfunction of sensor.
C. Control rod drop accident Automatic Action:
Rod withdrawal block Operator Action:
A. DETERMINE initiating condition from corresponding rod withdrawalblock alarm(s) and REFER TO operator action for alarm(s).
Standard:
Reference 3-ARP-9-5A and identifies APRM Ch 2 is down scale and proceeds to bypass APRM Ch 2 per 3-OI-92B CUE:Respond as stated in Alarm Response Instruction and Bypass APRM Ch 2 per 3-OI-92B.
13
STEP / STANDARD SAT / UNSAT Step 14:
NOTES
- 1) Only one APRM/OPRM in each trip system can be bypassed at a time.
- 2) All operations are performed on Panel 3-9-5 unless specifically stated otherwise.
- 3) In order to prevent inadvertent rod withdrawal block or Reactor scram while operating APRM BYPASS selector switch, Verify that the BLUE BYPASSED lights on Panel 9-14 Voters are extinguished prior to selecting any other channel to be bypassed. After bypassing a channel, the applicable BLUE BYPASSED status lights on Panel 9-14 Voters are required to be illuminated prior to testing, operating, or working on that channel. SAT UNSAT 6.1 Bypassing APRM/OPRM Channel N/A CAUTION
[QA/C] SPP-10.4 requires approval of the Plant Manager or his designee prior to any planned operation with APRMs bypassed unless bypassing is specifically allowed within approved procedures.
[ISE-HPS-92-RO1]
[1] REVIEW all precautions and limitations. REFER TO Section 3.0.
Standard:
Demonstrates reviewing precautions and limitations section 3.0.
CUE: If asked per note 2 above, Panel 9-14 Voter BLUE LIGHTS are extinguished.
Step 15:
Critical Step
[2] PLACE APRM BYPASS, 3-HS-92-7B/S3, to desired channel to be bypassed. SAT Standard: UNSAT PLACE APRM BYPASS, 3-HS-92-7B/S3, to APRM CH 2 N/A 14
STEP / STANDARD SAT / UNSAT Step 16:
[3] CHECK BLUE BYPASSED lights illuminated on Panel 3-9-14 Voters. SAT Standard: UNSAT Simulates observing BLUE BYPASS light illuminated on Panel 3- N/A 9-14 for APRM CH 2.
Cue: Blue Light is illuminated on Panel 3-9-14 for APRM CH 2.
Step 17:
[4] VERIFY white bypass light on Panel 3-9-5 is illuminated. SAT Standard: UNSAT Observes WHITE BYPASS light illuminated on Panel 3-9-5. N/A Note to NRC Examiner: If needed, cue student to proceed with actions required to continue rod movements.Student may continue at step 18 or 21.
Step 18:
6.6.2 Actions Required During and Following Control Rod Withdrawal (continued)
[6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN SAT PERFORM the following at the Unit Supervisors discretion to UNSAT REINITIALIZE the RBM:
N/A
[6.1] PLACE CRD POWER, 3-HS-85-46 in the OFF position to deselect the Control Rod.
Standard:
CRD POWER, 3-HS-85-46 in the OFF position.
15
STEP / STANDARD SAT / UNSAT Step 19:
[6.2] PLACE CRD POWER, 3-HS-85-46, in the ON position.
UNSAT Standard:
N/A PLACED CRD POWER, 3-HS-85-46, in the ON position.
Step 20:
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and SAT PERFORM applicable section for Control Rod withdrawal.
UNSAT Standard:
N/A Continues with Control Rod Movement Cue:If asked,Proceed with Control Rod Movement.
Step 21:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
16
STEP / STANDARD SAT / UNSAT Step 22:
[2] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 23:
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 24:
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Termination Criteria: When Control Rod is at position 04, state End of Task STOP TIME:
17
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is at 30% power
- Startup Sequence Control Rod Movement Data Sheet 3-SR-3.1.3.5(A) completed through group 58.
INITIATING CUES:
The US has directed you to raise Reactor Power to 40% per 3-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 59; Control Rod 22-39.
18
Job Performance Measure (JPM) 2-EOI APPENDIX-6E INJECTION SUBSYSTEM LINEUP SITE: BFN JPM TITLE:
CS SYSTEM II JPM NUMBER: 257A U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-35/ Lineup Injection Subsystem-Core TASK NUMBER / TASK TITLE(S): Spray Loop I(II) in Accordance with EOI Appendix 6D(E)
K/A RATINGS: RO: 3.9 SRO: 3.9 209001 Low Pressure Core Spray SystemA4.08 Ability to K/A No. &STATEMENT: manually operate and/or monitor in thecontrol room: Reactor water level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 2 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _257A U2_
TASK STANDARD: Perform operations necessary to identify and corrects Inboard and Outboard Injection Valve lineup in order to inject water into the RPV with Core Spray System II to recover level Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-EOI APPENDIX-6E VALIDATIONTIME: 8 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 12/06/10 All Initial issue 1 04/27/15 All General revision & re-format 3
SIMULATOR SETUP IC 28 Exam IC 283
- 1. Open Schedule File
- 2. Open Event File
- 3. Reset to IC-28and take out of freeze.
- 4. CLOSE 2-FCV-75-51 Console
- 5. OPEN 2-FCV-75-53 Operator
Instructions
- 7. Open 6 ADS Valves.
- 8. Wait until various alarms with Supp Pool Temp High come in to save IC.
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 15 75% 5 Yes INSIDE DRYWELL CS04A CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV II CS02B CS INBOARD 15 N/A N/A Yes INJECTION VALVE AUTO OPENING FAILURE (FCV 53)
RH06A RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV I RH06B RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV II RC01 RCIC TURBINE TRIP 15 N/A N/A Yes SYSTEM FAILURE HP04 HPCI STEAM 15 N/A N/A Yes SUPPLY VALVE AUTO OPENING FAILURE FW01A CONDENSATE 15 N/A 10 Yes PUMP TRIP 2A 4
FW01B CONDENSATE 15 N/A 10 Yes PUMP TRIP 2B FW01C CONDENSATE 15 N/A 10 Yes PUMP TRIP 2C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): JPM 257A U2 Core Spray Alt Inj.sch Event File(s): JPM 257A U2 Core Spray Alt Inj.evt 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is Shutdown
- RPV Water Level is lowering slowly.
- 1-EOI-1 has been entered and followed to RC-L6.
INITIATING CUES:
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above
(-)162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II.
6
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
Location: Unit 2 Control Room Attachments: 1. NPSH Monitoring
[1] VERIFY OPEN the following valves:
- 2-FCV-75-30, CORE SPRAY PUMP 2B SUPPR POOL SUCT UNSAT VLV
- 2-FCV-75-39, CORE SPRAY PUMP 2D SUPPR POOL SUCT N/A VLV Standard:
Verifies2-FCV-75-30 and 2-FCV-75-39 are open.
Step 2:
[1] (continued)VERIFY OPEN the following valves: Critical Step
- 2-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. SAT UNSAT Standard:
N/A Recognizes 2-FCV-75-51 is closed and 2-FCV-75-53 is open, valve closes 2-FCV-75-53 and Opens 2-FCV-75-51.
Note to Examiner: Student will realignper OPDP-8 Conduct of Ops or OI-75, Core Spray System line up.
7
STEP / STANDARD SAT / UNSAT Step 3:
[2] VERIFY CLOSED 2-FCV-75-50, CORE SPRAY SYS II SAT TESTVALVE.
UNSAT Standard:
N/A Verifies 2-FCV-75-50 closed Step 4:
Critical Step
[3] VERIFY CS Pump 2B and/or 2D running.
SAT Standard:
UNSAT Starts Core Pumps 2B and/or 2D N/A (Only starting one pump is Critical, the second pump is optional).
Step 6:
[4] WHEN RPV pressure is below 450 psig, THEN Critical Step THROTTLE2-FCV-75-53, CORE SPRAY SYS II INBDINJECT VALVE, SAT as necessary to control injection at or below4000 gpm per pump.
UNSAT Standard:
N/A Verifies pressure < 450 psig and opens 2-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or
<8000 gpm for 2 pumps).
Step 7:
CAUTION Continuous operation with inadequate NPSH may result in pump damage or pump inoperability.
[5] MONITOR Core Spray Pump NPSH using Attachment 1.
UNSAT Standard:
Operator comparesCore Spray Pump flow rate with Suppression N/A Pool temperature and Suppression Pool pressure and Determined adequate NPSH.
Termination Criteria: Once rector Water Level is > TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure.
STOP TIME:
8
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is Shutdown
- RPV Water Level is lowering slowly.
- 1-EOI-1 has been entered and followed to RC-L6.
INITIATING CUES:
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above 162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II.
9
Job Performance Measure (JPM) 3-EOI APPENDIX-6E INJECTION SUBSYSTEM LINEUP SITE: BFN JPM TITLE:
CS SYSTEM II JPM NUMBER: 257A U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-35/ Lineup Injection Subsystem-Core TASK NUMBER / TASK TITLE(S): Spray Loop I(II) in Accordance with EOI Appendix 6D(E)
K/A RATINGS: RO: 3.9 SRO: 3.9 209001 Low Pressure Core Spray System A4.08 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor water level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 2 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _257A U3_
TASK STANDARD: Perform operations necessary to identify and corrects Inboard and Outboard Injection Valve lineup in order to inject water into the RPV with Core Spray System II to recover level Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 3-EOI APPENDIX-6E VALIDATIONTIME: 5 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 12/06/10 All Initial issue 1 04/27/15 All General revision & re-format 3
SIMULATOR SETUP IC 28 Exam IC 283
- 1. Open Schedule File
- 2. Open Event File
- 3. Reset to IC-28 and take out of freeze.
- 4. CLOSE 2-FCV-75-51 Console
- 5. OPEN 2-FCV-75-53 Operator
Instructions
- 7. Open 6 ADS Valves.
- 8. Wait until various alarms with Supp Pool Temp High come in to save IC.
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 15 75% 5 Yes INSIDE DRYWELL CS04A CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV II CS02B CS INBOARD 15 N/A N/A Yes INJECTION VALVE AUTO OPENING FAILURE (FCV 53)
RH06A RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV I RH06B RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV II RC01 RCIC TURBINE TRIP 15 N/A N/A Yes SYSTEM FAILURE HP04 HPCI STEAM 15 N/A N/A Yes SUPPLY VALVE AUTO OPENING FAILURE FW01A CONDENSATE 15 N/A 10 Yes PUMP TRIP 3A 4
FW01B CONDENSATE 15 N/A 10 Yes PUMP TRIP 3B FW01C CONDENSATE 15 N/A 10 Yes PUMP TRIP 3C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): JPM 257A U3 Core Spray Alt Inj.sch Event File(s): JPM 257A U3 Core Spray Alt Inj.evt 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is Shutdown
- RPV Water Level is lowering slowly.
- 1-EOI-1 has been entered and followed to RC-L6.
INITIATING CUES:
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above
(-)162 inches (TAF) using Core Spray System II as directed by 3-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II.
6
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
Location: Unit 3 Control Room Attachments: 1. NPSH Monitoring
[1] VERIFY OPEN the following valves:
- 3-FCV-75-30, CORE SPRAY PUMP 3B SUPPR POOL SUCT UNSAT VLV
- 3-FCV-75-39, CORE SPRAY PUMP 3D SUPPR POOL SUCT N/A VLV Standard:
Verifies3-FCV-75-30 and 3-FCV-75-39 are open.
Step 2:
Critical Step
[1] (continued) VERIFY OPEN the following valves:
- 3-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE.
SAT UNSAT Standard:
N/A Recognizes 3-FCV-75-51 is closed and 3-FCV-75-53 is open, closes 3-FCV-75-53 and Opens 3-FCV-75-51.
Note to Examiner: Student will realignper OPDP-8 Conduct of Ops or OI-75, Core Spray System line up.
7
STEP / STANDARD SAT / UNSAT Step 3:
[2] VERIFY CLOSED 3-FCV-75-50, CORE SPRAY SYS II TEST SAT VALVE.
UNSAT Standard:
N/A Verifies 3-FCV-75-50 closed Step 4:
Critical Step
[3] VERIFY CS Pump 3B and/or 3D running.
SAT Standard:
UNSAT Starts Core Pumps 3B and/or 3D (Only starting one pump is N/A Critical, the second pump is optional).
Step 6:
[4] WHEN RPV pressure is below 450 psig, THEN Critical Step THROTTLE 3-FCV-75-53, CORE SPRAY SYS II INBDINJECT VALVE, SAT as necessary to control injection at or below4000 gpm per pump.
UNSAT Standard:
N/A Verifies pressure < 450 psig and opens 3-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or
<8000 gpm for 2 pumps).
Step 7:
CAUTION Continuous operation with inadequate NPSH may result in pump damage or pump inoperability.
[5] MONITOR Core Spray Pump NPSH using Attachment 1.
UNSAT Standard:
Operator compares Core Spray pump flow rate with Suppression N/A Pool temperature and Suppression Pool pressure and Determined adequate NPSH.
Termination Criteria: Once rector Water Level is > TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure.
STOP TIME:
8
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is Shutdown
- RPV Water Level is lowering slowly.
- 1-EOI-1 has been entered and followed to RC-L6.
INITIATING CUES:
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level using Core Spray System II as directed by 3-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. Directed level band is +2 to +51 inches.
9
Job Performance Measure (JPM) 2-EOI Appendix-11F Alternate RPV Pressure Control SITE: BFN JPM TITLE:
Systems: RFPT On Minimum Flow JPM NUMBER: 670A U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-58 Lineup Alternate RPV Pressure Control TASK NUMBER / TASK TITLE(S): Systems- RFPT on Minimum Flow IAW EOI Appendix 11F K/A RATINGS: RO: 3.6SRO: 3.6 239001 Main and Reheat Steam System A1.01 Ability to predict and/or monitor changes in parameters associated with K/A No. &STATEMENT:
operating the MAIN ANDREHEAT STEAM SYSTEM controls including: Main steam pressure RELATED PRA INFORMATION: None SAFETY FUNCTION: 3 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _670A U2_
TASK STANDARD: Perform operations necessary to necessary to place one RFPT in pressure control as directed by 2-EOI Appendix-11F.
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 2-EOI-APPENDIX-11F VERIFICATION TIME: 12 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 284 Malfunctions Description Event Severity Delay Initial set fw15a SPURIOUS RFP 15 N/A 0 N/A BEARING LOW OIL PRESSURE tc03a-j Fail Bypass Valves 1 0% 0 N/A closed ad01e 20 SRV 1-31 stuck open 1 20% 0 N/A 20%
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Initial Setup:
- 1. Reset to IC 28
- 2. Manually Scram RX
- 3. Trip 2A and 2B RFPT
- 5. Insert Manual Trigger #1
- 7. Verify Auto Trigger #15 is ACTIVE
- 8. Freeze simulator and save IC.
Schedule Files:
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 4
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 2C.
INITIATING CUES:
The Unit Supervisor directs you to place 2A RFPT in alternate pressure control, as directed by 2-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig.
5
START TIME STEP / STANDARD SAT / UNSAT Step 1:
[1] IF BOTH of the following exist:
- Emergency RPV Depressurization is required, AND
- Group 1 Isolation Signal exists, THEN SAT EXIT this procedure and ENTER EOI Appendix 11H. UNSAT N/A Standard:
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve.
Step 2:
[2] VERIFY MSIVs open.
UNSAT Standard:
N/A Verifies MSIVs OPEN 6
STEP / STANDARD SAT / UNSAT Step 3:
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. SAT Standard: UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 4:
[4] PLACE RFPTs in service as follows:
[4.1] VERIFY the following:
[4.1.1] At least one condensate pump running.
[4.1.2] At least one condensate booster pump running.
UNSAT
[4.1.3] Condensate System aligned to supply suction toRFPs.
N/A Standard:
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs.
Step 5:
[4.2] VERIFY Main Oil Pump running for each RFPT to bestarted. SAT Standard: UNSAT Verifies main oil pump running for RFPT 2A N/A Step 6:
Critical Step
[4.3] VERIFY CLOSED 2-FCV-3-19, RFP 2ADISCHARGE VALVE.
SAT Standard:
UNSAT VERIFY CLOSED 2-FCV-3-19, RFP 2A DISCHARGE VALVE.
N/A 7
STEP / STANDARD SAT / UNSAT Step 7:
Critical Step
[4.4] DEPRESS 2-HS-46-8A RFPT 2A SPEED CONT RAISE/LOWER, and VERIFY amber lightis illuminated. SAT Standard: UNSAT Depresses 2-HS-46-8A N/A Step 8:
[4.5] DEPRESS 2-HS-3-124A, RFPT 2A TRIP RESET. Critical Step Standard: SAT Depresses 2-HS-3-124A and verifies the 2-Z1-1-123 LP Stop Valve and UNSAT 2-Z1-127 HP Stop Valve comes OPEN.
N/A Step 9:
Critical Step
[4.6] PLACE 2-HS-46-112A RFPT 2A START/LOCAL ENABLE, in START. SAT Standard: UNSAT Places 2-HS-46-112A in START N/A Note to Examiner:
RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10:
Critical Step
[4.7] CHECK RFPT 2A speed increases to approximately 600 rpm.
SAT Standard:
UNSAT Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 2-EOI-APPENDIX-11F. N/A CUE:
US: Proceed as directed per 2-EOI-APPENDIX-11F.
AO: Reports an oil leak of ~5 gpm on RFPT A bearings.
8
STEP / STANDARD SAT / UNSAT Step 11:
[1] IF BOTH of the following exist:
- Emergency RPV Depressurization is required, AND
UNSAT Standard: N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve.
Step 12:
[2] VERIFY MSIVs open. SAT Standard: UNSAT Verifies MSIVs OPEN N/A 9
STEP / STANDARD SAT / UNSAT Step 13:
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. SAT Standard: UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 14:
[4] PLACE RFPTs in service as follows:
[4.1] VERIFY the following:
[4.1.1] At least one condensate pump running.
[4.1.2] At least one condensate booster pump running.
UNSAT
[4.1.3] Condensate System aligned to supply suction toRFPs.
N/A Standard:
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs.
Step 15:
[4.2] VERIFY Main Oil Pump running for each RFPT to be started. SAT Standard: UNSAT Verifies main oil pump running for RFPT 2B N/A Step 16:
Critical Step
[4.3] VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE.
SAT Standard:
UNSAT VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE.
N/A 10
STEP / STANDARD SAT / UNSAT Step 17:
Critical Step
[4.4] DEPRESS 2-HS-46-9A, RFPT 2BSPEED CONT RAISE/LOWER, and VERIFY amber light is illuminated. SAT Standard: UNSAT Depresses 2-HS-46-9A N/A Step 18:
Critical Step
[4.5] DEPRESS 2-HS-3-150A, RFPT 2B TRIP RESET.
SAT Standard:
UNSAT Depresses 2-HS-3-150A and verifies the 2-ZI-1-133 LP Stop Valve and 2-FCV-135 HP Stop Valve comes OPEN. N/A Step 19:
Critical Step
[4.6] PLACE 2-HS-46-138A, RFPT 2B START/LOCAL ENABLE, in START. SAT Standard: UNSAT Places 2-HS-46-138A in START N/A Step 20:
[4.7] CHECK RFPT 2B speed increases to approximately 600 rpm. SAT Standard: UNSAT Verifies RFPT 2B speed increases to approximately 600 rpm N/A 11
STEP / STANDARD SAT / UNSAT Step 21:
[4.8] VERIFY OPEN 2-FCV-3-13, RFP2B MIN FLOW VALVE. SAT Standard: UNSAT Verifies 2-FCV-3-13 OPEN N/A Step 21:
CAUTION RFP discharge pressure is limited to below 1250 psig to avoid system damage.
[4.9] PLACE 2-HS-46-9A, RFPT 2B SPEED CONT RAISE/LOWER in Critical Step RAISE to raise RFPT speed, maintaining discharge pressure less than 1250 psig. SAT Standard: UNSAT Raises RFPT speed using Manual Speed Control Handswitch, N/A maintaining discharge pressure <1250 psig as indicated on 2-PI-3-9A RFPT 2B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable).
STOP TIME END OF TASK 12
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 2C.
INITIATING CUES:
The Unit Supervisor directs you to place 2A RFPT in alternate pressure control, as directed by 2-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig.
13
Job Performance Measure (JPM) 3-EOI Appendix-11F Alternate RPV Pressure Control SITE: BFN JPM TITLE:
Systems: RFPT On Minimum Flow JPM 670A JPM NUMBER: REVISION: 0 U3 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-58 Lineup Alternate RPV Pressure Control TASK NUMBER / TASK TITLE(S): Systems- RFPT on Minimum Flow IAW EOI Appendix 11F K/A RATINGS: RO: 3.6 SRO: 3.6 239001 Main and Reheat Steam System A1.01 Ability to predict and/or monitor changes in parameters associated with K/A No. & STATEMENT:
operating the MAIN AND REHEAT STEAM SYSTEM controls including: Main steam pressure RELATED PRA INFORMATION: None SAFETY FUNCTION: 3 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _______
TASK STANDARD: Perform operations necessary to necessary to place one RFPT in pressure control as directed by 3-EOI Appendix-11F.
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 3-EOI-APPENDIX-11F VERIFICATION TIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 284 Malfunctions Description Event Severity Delay Initial set fw15a SPURIOUS RFP 15 N/A 0 N/A BEARING LOW OIL PRESSURE tc03a-j Fail Bypass Valves 1 0% 0 N/A closed ad01e SRV 1-31 stuck open 1 26% 0 N/A Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set 3
Initial Setup:
- 1. Reset to IC 28
- 2. Manually Scram RX
- 3. Trip 2A and 2B RFPT
- 5. Insert Manual Trigger #1
- 7. Verify Auto Trigger #15 is ACTIVE
- 8. Freeze simulator and save IC.
Schedule Files:
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/11/15 All Initial issue 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3. The Unit 3 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 3C.
INITIATING CUES:
The Unit Supervisor directs you to place 3A RFPT in alternate pressure control, as directed by 3-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig.
6
START TIME STEP / STANDARD SAT / UNSAT Step 1:
[1] IF BOTH of the following exist:
- Emergency RPV Depressurization is required, AND
UNSAT Standard: N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve.
Step 2:
[2] VERIFY MSIVs open.
SAT Standard:
UNSAT Verifies MSIVs OPEN N/A 7
STEP / STANDARD SAT / UNSAT Step 3:
[3] VERIFY Hotwell Pressure at or below -7 in. Hg.
SAT Standard:
UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 4:
[4] PLACE RFPTs in service as follows:
[4.1] VERIFY the following:
[4.1.1] At least one condensate pump running.
[4.1.2] At least one condensate booster pump running.
[4.1.3] Condensate System aligned to supply suction to RFPs.
UNSAT Standard:
N/A Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs.
Step 5:
[4.2] VERIFY Main Oil Pump running for each RFPT to be started.
SAT Standard:
UNSAT Verifies main oil pump running for RFPT 3A N/A Step 6: Critical Step
[4.3] VERIFY CLOSED 3-FCV-3-19, RFP 3A DISCHARGE VALVE.
SAT Standard:
UNSAT VERIFY CLOSED 3-FCV-3-19, RFP 3A DISCHARGE VALVE.
N/A 8
STEP / STANDARD SAT / UNSAT Step 7:
[4.4] DEPRESS 3-HS-46-8A, RFPT 3A SPEED CONT RAISE/LOWER, Critical Step and VERIFY amber light is illuminated.
SAT Standard:
UNSAT Depresses 3-HS-46-8A N/A Step 8:
[4.5] DEPRESS 3-HS-3-124A, RFPT 3A TRIP RESET. Critical Step Standard: SAT Depresses 3-HS-3-124A and resets RFPT Trip and verifies the 3-ZI UNSAT 123 LP Stop Valve and 3-ZI-127 HP Stop Valve comes OPEN.
N/A Step 9:
[4.6] PLACE 3-HS-46-112A RFPT 3A START/LOCAL ENABLE, in Critical Step START.
SAT Standard:
UNSAT Places 3-HS-46-112A in START N/A Note to Examiner:
RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10:
[4.7] CHECK RFPT 3A speed increases to approximately 600 rpm.
SAT Standard:
UNSAT Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 3-EOI-APPENDIX-11F. N/A CUE:
US: Proceed as directed per 3-EOI-APPENDIX-11F.
AO: Reports an oil leak of ~5 gpm on RFPT A bearings.
9
STEP / STANDARD SAT / UNSAT Step 11:
[1] IF BOTH of the following exist:
- Emergency RPV Depressurization is required, AND
- Group 1 Isolation Signal exists, THEN EXIT this procedure and ENTER EOI Appendix 11H. SAT UNSAT Standard:
N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve.
Step 12:
[2] VERIFY MSIVs open.
SAT Standard:
UNSAT Verifies MSIVs OPEN N/A 10
STEP / STANDARD SAT / UNSAT Step 13:
[3] VERIFY Hotwell Pressure at or below -7 in. Hg.
SAT Standard:
UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 14:
[4] PLACE RFPTs in service as follows:
[4.1] VERIFY the following:
[4.1.1] At least one condensate pump running.
[4.1.2] At least one condensate booster pump running.
[4.1.3] Condensate System aligned to supply suction to RFPs.
UNSAT Standard:
N/A Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs.
Step 15:
[4.2] VERIFY Main Oil Pump running for each RFPT to be started.
SAT Standard:
UNSAT Verifies main oil pump running for RFPT 3B N/A Step 16: Critical Step
[4.3] VERIFY CLOSED 3-FCV-3-12, RFP 3B DISCHARGE VALVE.
SAT Standard:
UNSAT VERIFY CLOSED 3-FCV-3-12, RFP 3B DISCHARGE VALVE.
N/A 11
STEP / STANDARD SAT / UNSAT Step 17:
[4.4] DEPRESS 3-HS-46-9A, RFPT 3B SPEED CONT RAISE/LOWER, Critical Step and VERIFY amber light is illuminated.
SAT Standard:
UNSAT Depresses 3-HS-46-9A N/A Step 18:
[4.5] DEPRESS 3-HS-3-150A, RFPT 3B TRIP RESET. Critical Step Standard: SAT Depresses 3-HS-3-150A and verifies the 3-ZI-1-133 LP Stop Valve and 3- UNSAT FCV-135 HP Stop Valve comes OPEN.
N/A Step 19:
[4.6] PLACE 3-HS-46-138A, RFPT 3B START/LOCAL ENABLE, in Critical Step START.
SAT Standard:
UNSAT Places 3-HS-46-138A in START N/A Step 20:
[4.7] CHECK RFPT 3B speed increases to approximately 600 rpm.
SAT Standard:
UNSAT Verifies RFPT 3B speed increases to approximately 600 rpm N/A 12
STEP / STANDARD SAT / UNSAT Step 21:
[4.8] VERIFY OPEN 3-FCV-3-13, RFP 3B MIN FLOW VALVE. Critical Step Standard: SAT Verifies 3-FCV-3-13 OPEN UNSAT N/A Step 21:
CAUTION RFP discharge pressure is limited to below 1250 psig to avoid system damage.
[4.9] PLACE 3-HS-46-9A, RFPT 3B SPEED CONT RAISE/LOWER in Critical Step RAISE to raise RFPT speed, maintaining discharge pressure less than 1250 psig.
SAT Standard:
UNSAT Raises RFPT speed using Manual Speed Control Handswitch, N/A maintaining discharge pressure <1250 psig as indicated on 3-PI-3-9A RFPT 3B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable).
STOP TIME END OF TASK 13
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3. The Unit 3 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 3C.
INITIATING CUES:
The Unit Supervisor directs you to place 3A RFPT in alternate pressure control, as directed by 3-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig.
14
N2 MAKEUP TO PRIMARY CONTAINMENT WITH SITE: BFN JPM TITLE:
2-EOI-APPENDIX-14A JPM NUMBER: 669 U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-77 Lineup nitrogen Makeup to primary TASK NUMBER / TASK TITLE(S):
Containment IAW EOI-APPENDIX-14A K/A RATINGS: RO: 3.7SRO: 3.8 223001 Primary Containment System and Auxiliaries A2.04; Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT SYSTEM AND AUXILIARIES ; and K/A No. &STATEMENT: (b) based on those predictions, use procedures to correct, control, or mitigate the consequences ofthose abnormal conditions or operations: High containment/drywell hydrogen concentration RELATED PRA INFORMATION: None SAFETY FUNCTION: 5 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _669 U2__
TASK STANDARD: Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration.
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 2-EOI-APPENDIX-14A VERIFICATION TIME: 15 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 285
- 1. Open Schedule File
- 2. Open Event File
- 3. Reset to IC-28 and take out of freeze.
Console
- 6. Fire Trigger 2 Operator
- 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch Instructions in BYPASS per EOI APPDX 19
- 9. Wait for Group 6 schedule file to time out and alrms to settle
- 10. Freeze simulator and save IC.
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 2 100 0 Yes INSIDE DRYWELL TH23 FUEL CLADDING 2 100% 0 N/A DAMAGE RC08 RCIC STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE HP04 HPCI STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE CS04A CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV II RD01A CRD PUMP TRIP 1 N/A 0 N/A 2A RD01B CRD PUMP TRIP 1 N/A 0 N/A 2B FW01A CONDENSATE 1 N/A 0 N/A PUMP TRIP 2A FW01B CONDENSATE 1 N/A 0 N/A 3
PUMP TRIP 2B FW01C CONDENSATE 1 N/A 0 N/A PUMP TRIP 2C PC08 H2 IN DRYWELL_ 2 29 0 N/A PC09 OXYGEN IN 2 2.8 0 N/A DRYWELL_
PC10 H2 IN 2 18 0 N/A SUPPRESSION POOL_
PC11 OXYGEN IN 2 1.5 0 N/A SUPPRESSION POOL_
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLOXA554C9 DW EQUIP DRAIN 2 N/A N/A ON SUMP LEVEL ABNORMAL Schedule File(s):
- JPM 669 U2 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.sch
- Appendix\App. 8E.sch
- JPM 669 U2 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.evt 4
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/15 All Initial issue 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is shutdown.
- 2-EOI-APPENDIX-12has been completed
- 2-EOI-APPENDIX-19 has been completed.
- PCIS Group 6 has been overridden per 2-EOI-APPENDIX-8E.
INITIATING CUES:
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2-EOI-APPENDIX-14A beginning on step 2.
6
START TIME STEP / STANDARD SAT / UNSAT Step 1:
- 2. MONITOR Drywell and Suppression Chamber H2 and O2concentrations on one or more of the following displays(2-EOI Appendix 19):
- 2-MON-76-110, H2/O2 ANALYZER (Panel 2-9-55)
UNSAT
- 2-XR-76-110, H2/O2 CONCENTRATION (Panel 2-9-54)
N/A Standard:
Verifies H2 and O2 concentrations Step 2:
- 3. IF ................. Drywell/Suppression Chamber H2 /O2 analyzer is or becomes inoperable, SAT THEN ...........NOTIFY Chemistry Lab to sample Drywell andSuppression Chamber for H2 and O2 using CI-644.
UNSAT Standard:
N/A Verifies Drywell/Suppression Chamber H2 /O2 analyzers are Operable 7
STEP / STANDARD SAT / UNSAT Step 3:
4.WHEN ......... Drywell or Suppression Chamber H2 or O2 concentration is increasing,THEN ........... CONTINUE in this procedure. SAT Standard: UNSAT Observes a rise in Drywell H2 Concentration and continues with N/A procedure.
Step 4:
NOTE This procedure assumes that the normal makeup is from N2 Storage Tank B.
- 5. DISPATCH personnel to N2 Storage Tank B to CHECK 0-PI-76-331, UNSAT N2 TANK B PRESSURE INDICATOR between 160 and 190 psig.
N/A Standard:
Dispatches UO to verifyN2 Storage Tank B Pressure CUE: N2 Storage Tank B Pressure is reading 180 psig Step 5:
- 6. DETERMINE area with highest H2 and/or O2 concentrations and Critical Step INFORM SRO.
SAT Standard:
UNSAT Correctly determines highest concentration is in the drywell and informs US N/A CUE: If asked about 15 minute sample time, state 15 minutes have elapsed 8
STEP / STANDARD SAT / UNSAT Step 6:
Critical Step
- 7. VERIFY PCIS RESET (Panel 2-9-4).
SAT Standard:
UNSAT Verifies PCIS RESET on Panel 2-9-4 N/A Step 7:
Critical Step
- 8. IF ................. It is desired to makeup N2 to the Suppression Chamber,THEN ...........CONTINUE in this procedure at Step 10. SAT Standard: UNSAT Correctly determine step is not applicable and proceeds to step 9. N/A Step 8:
- 9. CONTROL Drywell H2 and O2 as follows:
Critical Step
- a. OPEN the following valves to admit N2 to Drywell (Panel 2-9-3):
- 2-FCV-76-18, DRYWELL N2 MAKEUP INBDISOLATION VLV
N/A OPENS 2-FCV-76-18, DRYWELL N2 MAKEUP INBD ISOLATION VLV &
2-FCV-76-17, PRI CTMT N2 MAKEUP OUTBD ISOLATION VLV Step 9:
- b. SLOWLY ADJUST 2-PC-76-14, DW/SUPPR CHBR N2 MU Critical Step PRESS CONTROL (Panel 2-9-3), to maintain flow > 55 and
<60 scfm on 2-XR-76-14, DW/SUPPR CHBR N2 MAKEUP SAT FLOW/PRESS (Panel 2-9-3), or as directed by SRO if SAMG execution is in progress.
UNSAT Standard:
N/A Achieves a flowrate between 55-60 scfm and monitors Drywell Hydrogen Concentration Lowering 9
STEP / STANDARD SAT / UNSAT Step 10:
- c. CONTINUEN2 admission to the Drywell UNTIL Drywell H2 andO2 are SAT below desired values.
UNSAT Standard:
N/A Monitors Drywell Hydrogen Concentration Note to Examiner: Once satisfied with N2 Flow established between 55 - 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task.
Pass/ Fail Criteria: Establish N2 Flow> 55 scfm and H2 Concentration on a downward trend.
STOP TIME END OF TASK 10
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is shutdown.
- 2-EOI-APPENDIX-12 has been completed
- 2-EOI-APPENDIX-19 has been completed.
- PCIS Group 6 has been overridden per 2-EOI-APPENDIX-8E.
INITIATING CUES:
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2-EOI-APPENDIX-14A beginning on step 2.
11
N2 MAKEUP TO PRIMARY CONTAINMENT WITH 3-SITE: BFN JPM TITLE:
EOI-APPENDIX-14A JPM NUMBER: 670 U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-77 Lineup nitrogen Makeup to primary TASK NUMBER / TASK TITLE(S):
Containment IAW EOI-APPENDIX-14A K/A RATINGS: RO: 3.7SRO: 3.8 223001 Primary Containment System and Auxiliaries A2.04; Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT SYSTEM AND AUXILIARIES ; and K/A No. &STATEMENT: (b) based on those predictions, use procedures to correct, control, or mitigate the consequences ofthose abnormal conditions or operations: High containment/drywell hydrogen concentration RELATED PRA INFORMATION: None SAFETY FUNCTION: 5 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _670 U3_
TASK STANDARD: Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration.
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 3-EOI-APPENDIX-14A VERIFICATION TIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 285
- 1. Open Schedule File
- 2. Open Event File
- 3. Reset to IC-28 and take out of freeze.
Console
- 6. Fire Trigger 2 Operator
- 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch Instructions in BYPASS per EOI APPDX 19
- 9. Wait for Group 6 schedule file to time out and alrms to settle
- 10. Freeze simulator and save IC.
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 2 100 0 Yes INSIDE DRYWELL TH23 FUEL CLADDING 2 100% 0 N/A DAMAGE RC08 RCIC STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE HP04 HPCI STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE CS04A CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV II RD01A CRD PUMP TRIP 1 N/A 0 N/A 2A RD01B CRD PUMP TRIP 1 N/A 0 N/A 2B 3
FW01C CONDENSATE 1 N/A 0 N/A PUMP TRIP 2C PC08 H2 IN DRYWELL_ 2 29 0 N/A PC09 OXYGEN IN 2 2.8 0 N/A DRYWELL_
PC10 H2 IN 2 18 0 N/A SUPPRESSION POOL_
PC11 OXYGEN IN 2 1.5 0 N/A SUPPRESSION POOL_
Overrides Description Event Severity Delay Initial set ZLOXA554C9 DW EQUIP DRAIN 2 N/A N/A ON SUMP LEVEL ABNORMAL Schedule File(s):
- JPM 669 U3 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.sch
- Appendix\App. 8E.sch
- JPM 669 U3 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.evt 4
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/15 All Initial issue 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is shutdown.
- 3-EOI-APPENDIX-12 has been completed.
- 3-EOI-APPENDIX-19 has been completed.
- PCIS Group 6 has been overridden per 3-EOI-APPENDIX-8E.
INITIATING CUES:
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 3-EOI-APPENDIX-14A beginning on step 2.
6
START TIME STEP / STANDARD SAT / UNSAT Step 1:
- 3. MONITOR Drywell and Suppression Chamber H2 and O2concentrations on one or more of the following displays(3-EOI Appendix 19):
- 3-MON-76-110, H2/O2 ANALYZER (Panel 3-9-55)
UNSAT
- 3-XR-76-110, H2/O2 CONCENTRATION (Panel 3-9-54)
N/A Standard:
Verifies H2 and O2 concentrations Step 2:
- 3. IF ................. Drywell/Suppression Chamber H2 /O2 analyzer is or becomes inoperable, SAT THEN ...........NOTIFY Chemistry Lab to sample Drywell UNSAT andSuppression Chamber for H2 and O2 using CI-644.
N/A Standard:
Verifies Drywell/Suppression Chamber H2 /O2 analyzers are Operable 7
STEP / STANDARD SAT / UNSAT Step 3:
- 4. WHEN ......... Drywell or Suppression Chamber H2 or O2 concentration is increasing,THEN ........... CONTINUE in this procedure. SAT Standard: UNSAT Observes a rise in Drywell H2 Concentration and continues with N/A procedure.
Step 4:
NOTE This procedure assumes that the normal makeup is from N2 Storage Tank B.
- 5. DISPATCH personnel to N2 Storage Tank B to CHECK 0-PI-76-331, UNSAT N2 TANK B PRESSURE INDICATOR between 160 and 190 psig.
N/A Standard:
Dispatches UO to verifyN2 Storage Tank B Pressure CUE: N2 Storage Tank B Pressure is reading 180 psig Step 5:
- 6. DETERMINE area with highest H2 and/or O2 concentrations and Critical Step INFORM SRO.
SAT Standard:
UNSAT Correctly determines highest concentration is in the drywell and informs US N/A CUE: If asked about 15 minute sample time, state 15 minutes have elapsed 8
STEP / STANDARD SAT / UNSAT Step 6:
Critical Step
- 7. VERIFY PCIS RESET (Panel 3-9-4).
SAT Standard:
UNSAT Verifies PCIS RESET on Panel 3-9-4 N/A Step 7:
Critical Step
- 8. IF ................. It is desired to makeup N2 to the Suppression Chamber,THEN ...........CONTINUE in this procedure at Step 10. SAT Standard: UNSAT Correctly determine step is not applicable and proceeds to step 9. N/A Step 8:
- 9. CONTROL Drywell H2 and O2 as follows:
Critical Step
- a. OPEN the following valves to admit N2 to Drywell (Panel 3-9-3):
- 3-FCV-76-18, DRYWELL N2 MAKEUP INBDISOLATION VLV
N/A OPENS 3-FCV-76-18, DRYWELL N2 MAKEUP INBD ISOLATION VLV
&3-FCV-76-17, PRI CTMT N2 MAKEUP OUTBD ISOLATION VLV Step 9:
- b. SLOWLY ADJUST 3-PC-76-14, DW/SUPPR CHBR N2 MUPRESS Critical Step CONTROL (Panel 3-9-3), to maintain flow between 55 and60 scfm on 3-XR-76-14, DW/SUPPR CHBR N2 MAKEUPFLOW/PRESS (Panel 3-SAT 9-3), or as directed by SRO if SAMGexecution is in progress.
UNSAT Standard:
N/A Achieves a flowrate between 55-60 scfm and monitors Drywell Hydrogen Concentration Lowering 9
STEP / STANDARD SAT / UNSAT Step 10:
- c. CONTINUE N2 admission to the Drywell UNTIL Drywell H2 and O2 are below desired values. SAT Standard: UNSAT Monitors Drywell Hydrogen Concentration N/A Note to Examiner: Once satisfied with N2 Flow established between 55 - 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task.
Pass/ Fail Criteria: Establish N2 Flow > 55 scfm and H2 Concentration on a downward trend.
STOP TIME END OF TASK 10
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is shutdown.
- 3-EOI-APPENDIX-12 has been completed.
- 3-EOI-APPENDIX-19 has been completed.
- PCIS Group 6 has been overridden per 3-EOI-APPENDIX-8E.
INITIATING CUES:
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 3-EOI-APPENDIX-14A beginning on step 2.
11
Restore Offsite Power to 4KV shutdown board at SITE: BFN JPM TITLE:
PNL 9-23 JPM NUMBER: 631 U2 REVISION: 0 TASK SRO STA UO NAUO APPLICABILITY:
U-082-NO-09 / Restore Offsite Power to 4KV TASK NUMBER / TASK TITLE(S):
shutdown board at PNL 9-23 K/A RATINGS: RO 3.4 SRO 3.4 262001 A.C. Electrical Distribution A4.02 Ability to manually operate and/or monitor in the control room: Synchroscope, K/A STATEMENT:
including understanding of running andincoming voltages RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 6 EVALUATION LOCATION: In -P la n t Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NATIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: 631 U2 RO SRO DATE: _______
TASK STANDARD: Perform operations necessary to restore offsite power to 4KV SD BD A from 4KV SD BUS 1.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure 0-OI-82 VERIFICATION TIME: 15 Min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 286 Console 1. Reset to IC 28 and take out of freeze Operator 2. Start A EDG and parallel with offsite Instructions 3. Open 4-kV Shutdown Board A Breaker 1614 Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set 3
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed.
I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- No Inclement weather currently exists in the area
- 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> ago, 4 KV Shutdown Board A was separated from Offsite Power in accordance with 0-OI-82, Standby Diesel Generator System.
INITIATING CUE:
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board A using the normal feeder breaker and remove DG A from parallel operation in accordance with 0-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23.
4
START TIME STEP / STANDARD SAT /
UNSAT Step 1:
0-OI-82 Standby Diesel Generator System Section 8.3 Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23 NOTE The following list of 4-kV shutdown board normal and alternate feeder breakers may be useful when performing this section:
__UNSAT Shutdown A B C D Board N/A Norm Feed Bkr 1614 1616 1718 1724 Alt Feed Bkr 1716 1714 1624 1618
[1] VERIFY 4-kV Shutdown Board A is being supplied power by its respective Diesel Generator as the only source of power.
Standard:
Verifies 4-kV Shutdown Board A is being supplied by DG A.
Step 2:
[2] VERIFY the associated 4kV shutdown board auto transfer lockout relay is tripped to MANUAL.
Diesel Handswitch Name Handswitch Panel SAT No.
4KV SD BD A UNSAT A 0-211-3EA 0-9-23-7 AUTO/LOCKOUT RESET N/A Standard:
Verifies 4KV SD BD A AUTO/LOCKOUT RESET, HS-0-211-A, is tripped to manual.
5
STEP / STANDARD SAT /
UNSAT Step 3:
[3] PLACE the synchroscope switch for the 4-kV shutdown board Critical Step feeder breaker that is to be paralleled with the Diesel Generator in ON. SAT Standard: UNSAT Places Synchroscope switch for 4-kV Shutdown Board A normal N/A feeder breaker 1614 to ON.
Step 4:
[4] VERIFY 4-kV Shutdown Bus 1(2) voltage is between 3950 Volts SAT and 4400 Volts and NOT undergoing abnormal voltage transients.
UNSAT Standard:
N/A Verifies 4-kV Shutdown Bus 1 voltage is between 3950 Volts and 4400 Volts and NOT undergoing abnormal voltage transients.
Step 5:
[5] VERIFY associated incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients.
Shutdown Instrument Name Instrument No. Panel Bd SAT A or B GEN SYNC 0-SI-82-0AB 0-9-23-7 FREQUENCY UNSAT C or D GEN SYNC 0-SI-82-0CD 0-9-23-8 FREQUENCY N/A Standard:
Verifies incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients using GEN SYNC FREQUENCY,0-SI-82-AB.
6
STEP / STANDARD SAT /
UNSAT Step 6:
CAUTION DO NOT parallel the Diesel Generators with an unstable offsite source or during inclementweather (e.g., lightning, heavy winds).
[6] IF 4-kV Shutdown Bus 1 (2) is experiencing abnormal voltage or UNSAT frequency conditions, THEN PERFORM the following:
N/A Standard:
STEP N/A Step 7:
CAUTION Only one Unit 1 and 2 Diesel Generator at a time is allowed to be operated in parallel with system.
Critical Step
[7] PULL and PLACE the associated Diesel Generator mode selector switch in PARALLELED WITH SYSTEM. SAT Diesel Handswitch Name Handswitch Panel UNSAT No.
A DG A MODE SELECT 0-HS-82-A/5A 0-9-23-7 N/A Standard:
Pulls DG A MODE SELECT switch 0-HS-82-A/5A and places it in PARALLELED WITH SYSTEM.
7
STEP / STANDARD SAT /
UNSAT Step 8:
CAUTION Failure of the PARALLELED WITH SYSTEM light to illuminate in the following step could indicate that the DG is still in SINGLE UNIT operation and result in overload when the DG output breaker is closed.
SAT UNSAT
[8] RELEASE the Diesel Generator mode selector switch and OBSERVE PARALLELED WITH SYSTEM light illuminated.
N/A Standard:
Releases the Diesel Generator A mode selector switch, 0-HS A/5A and observesPARALLELED WITH SYSTEM light is illuminated.
Step 9:
[9] ADJUST Diesel Generator frequency using the associated Diesel Generator governor control switch to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction.
Critical Step Diesel Handswitch Name Handswitch Panel No. SAT A DG A GOVERNOR 0-HS-82-A/3A 0-9-23-7 CONTROL UNSAT Standard: N/A AdjustsDiesel Generator A frequency using Diesel Generator governor control switch, 3-HS-82-A/3A, (in lower direction) to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction.
8
STEP / STANDARD SAT /
UNSAT Step 10:
[10] USE the associated Diesel Generator voltage regulator control switch to match Diesel Generator and System voltages.
Diesel Instrument Name Inst No. Panel DG A VOLT REGULATOR 0-HS-82-A/2A SAT CONT A GEN SYNC REF VOLTAGE 0-EI-82-AB 0-9-23-7 UNSAT SYSTEM SYNC REF 0-EI-211-0AB VOLTAGE N/A Standard:
Matches DG A voltage with system voltage using DG A VOLT REGULATOR CONT switch 0-HS-82-A/2A.
Step 11:
[11] WHEN the synchroscope needle is approximately 2 minutes on Critical Step the right hand side of the 12 o'clock position, THEN CLOSE the 4-kV shutdown board feeder breaker that is to be SAT paralleled with the Diesel Generator.
UNSAT Standard:
N/A Closesthe 4-kV shutdown board feeder breaker 1614 when the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position.
Step 12:
[12] PLACE the synchroscope switch for the 4-kV shutdown board SAT feeder breaker that was paralleled with the Diesel Generator in OFF.
UNSAT Standard:
N/A Places the synchroscope switch for BKR 1614 in OFF.
9
STEP / STANDARD SAT /
UNSAT Step 13:
NOTE If diesel operates greater than 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> at less than 50% load, the diesel should be loaded to full load for at least 30 minutes prior to engine shutdown. This will allow the engine to clean out any oil accumulations from the exhaust manifolds.
[13] IF DG has been operating at a low-load condition (50%) for an extended period of time (4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br />) THEN PERFORM the following (Otherwise N/A):
[13.1] USE the associated Diesel Generator's governor controlswitch and voltage regulator control switch toINCREASE kW and kVAR load, in increments of Critical Step 100kWevery 15 minutes.
SAT Diesel Handswitch Name Hands Panel witch UNSAT No.
DG A GOVERNOR CONTROL 0-HS-N/A 82-A/3A A 0-9-23-7 DG A VOLT REGULATOR 0-HS-CONTROL 82-A/2A
[13.2] OBSERVE the exhaust stack smoke concentration from outside the DG room after each incremental increase.
[13.3] STEP N/A
[13.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible.
[13.5] MAINTAIN 100% load for a minimum of 30 minutes.
Standard:
Loads DG to 2600 kW and 1850 kVAR by using 0-HS-82-A/3A and 0-HS-82-A/2A handswitches.
CUE: After first 100 kW load adjustment state 15 minutes have elapsed and no observable black smoke from exhaust stack for time compression and continue to full load.
10
STEP / STANDARD SAT /
UNSAT Step 14:
NOTE Lagging VARs should be maintained when adjusting kW load (rising or lowering). This may require kW load adjustment to be stopped periodically to allow for adjusting kVAR load. Once desired kW load is achieved, Illustration 1 should be referred to for determination of kVAR loading required to obtain a power factor (pf) of 0.8 lagging. Diesel generator kVAR load should then be adjusted to obtain a 0.8 pf lagging. IF system conditions will NOT permit the kVAR loading required to obtain a 0.8 pf lagging, kVAR load should be adjusted to the maximum kVAR lagging the system will allow.
SAT UNSAT
[14] USE the associated Diesel Generator's governor control switch and voltage regulator control switch to obtain desired kW and N/A kVAR load.
Diesel Handswitch Name Handswitch No. Panel DG A GOVERNOR CONTROL 0-HS-82-A/3A A 0-9-23-7 DG A VOLT REGULATOR CONT 0-HS-82-A/2A Standard:
Obtains desired kW and kVAR load using DG A Governor Control switch, 0-HS-82-A/3A and DG Volt Regulator Cont switch, 0-HS-82-A/2A.
CUE: state 30 minutes have elapsed continue with procedure.
Step 15:
[15] MONITOR the offsite source that is paralleled with the Diesel Generator. SAT
[16] IF abnormal voltage or frequency transients are experienced, UNSAT THEN N/A Standard:
Step is N/A 11
STEP / STANDARD SAT /
UNSAT Step 16:
[17] WHEN Parallel with System operation is no longer desired, THEN UNLOAD the Diesel Generator as follows:
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVARlimit may result in a reverse power trip of the Diesel Generator output breaker.
[17.1] USE the associated Diesel Generator's governor control Critical Step switch and voltage regulator control switch to reduce generator load to approximately 300 kW and SAT 250 kVAR:
UNSAT Diesel Instrument Name Inst No. Panel N/A DG A GOVERNOR CONTROL 0-HS-82-A/3A DG A VOLTAGE 0-HS-82-A/2A A REGULATOR CONTROL 0-9-23-7 DG A KILOWATTS 0-JI-82-A/A DG A KILOVARS 0-VAR-82-A/A Standard:
Unloads the DG to approximately 300 KW and 250 kVAR.
Step 17
[17.2] PLACE the associated Diesel Generator breaker control Critical Step switch in TRIP SAT Diesel Handswitch Name Handswitch No. Panel A DG A BKR 1818 0-HS-211-A/22A 0-9-23-7 UNSAT N/A Standard:
Trips Diesel Generator breaker 1818.
12
STEP / STANDARD SAT /
UNSAT Step 18:
[17.3] PULL and PLACE the associated Diesel Generator mode Critical Step selector switch in SINGLE UNIT.
SAT Diesel Handswitch Name Handswitch No. Panel A DG A MODE SELECT 0-HS-211-A/5A 0-9-23-7 UNSAT N/A Standard:
Pulls and places 0-HS-211-A/5A to Single Unit.
Step 19:
[17.4] RELEASE the Diesel Generator mode selector switch and SAT OBSERVE the SINGLE UNIT light illuminated.
UNSAT Standard:
N/A Verifies Single Unit light illuminated.
CUE: ANOTHER OPERATOR WILL CONTINUE FROM HERE STOP TIME END OF TASK 13
Provide to Applicant INITIAL CONDITIONS:
You are an Operator on Unit 2.
- No Inclement weather currently exists in the area
- 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> ago, 4 KV Shutdown Board A was separated from Offsite Power in accordance with 0-OI-82, Standby Diesel Generator System.
INITIATING CUE:
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board A using the normal feeder breaker and remove DG A from parallel operation in accordance with 0-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23.
14
Restore Offsite Power to 4KV shutdown board at PNL 9-SITE: BFN JPM TITLE:
23 U-3 JPM NUMBER: 631 REVISION: 0 TASK SRO STA UO NAUO APPLICABILITY:
U-082-NO-09 / Restore Offsite Power to 4KV TASK NUMBER / TASK TITLE(S):
shutdown board at PNL 9-23 K/A RATINGS: RO 3.4 SRO 3.4 262001 A.C. Electrical Distribution A4.02 Ability to manually operate and/or monitor in the control K/A STATEMENT: room: Synchroscope, including understanding of running and incoming voltages RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 6 EVALUATION LOCATION: In -P la n t Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: 631 RO SRO DATE: _______
TASK STANDARD: Perform operations necessary to restore offsite power to 4KV SD BD EC.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure 3-OI-82 VERIFICATION TIME: 15 Min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 286
- 1. Reset to IC 28 and take out of freeze Console
- 2. Start C EDG and parallel with offsite Operator
- 3. Open 4-kV Shutdown Board 3EC Breaker 1338 Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Batch / Pref File(s):
3
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed.
I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- No Inclement weather currently exists in the area
- 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> ago, 4 KV Shutdown Board 3EC was separated from Offsite Power in accordance with 3-OI-82, Standby Diesel Generator System.
INITIATING CUE:
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board 3EC using the normal feeder breaker and remove DG 3C from parallel operation in accordance with 3-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23.
4
START TIME STEP / STANDARD SAT /
UNSAT Step 1:
3-OI-82 Standby Diesel Generator System Section 8.3 Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23 NOTE The following list of 4-kV shutdown board normal and alternate feeder breakers may be useful when performing this section:
SAT UNSAT Shutdown 3EA 3EB 3EC 3ED Board N/A Norm Feed Bkr 1334 1336 1338 1342 Alt Feed Bkr 1726 1728 1626 1628
[1] VERIFY 4-kV Shutdown Board 3EC is being supplied power by its respective Diesel Generator as the only source of power.
Standard:
Verifies 4-kV Shutdown Board EC is being supplied by DG C Step 2:
[2] VERIFY the associated 4kV shutdown board auto transfer lockout relay is tripped to MANUAL.
SAT Diesel Handswitch Name Handswitch No. Panel 4KV SD BD 3EC 3-43-211- UNSAT 3C 3-9-23 AUTO/LOCKOUT RESET 3EC N/A Standard:
Verifies 4KV SD BD 3EC AUTO/LOCKOUT RESET, 3-43-211-3EC, is tripped to manual.
5
STEP / STANDARD SAT /
UNSAT Step 3:
[3] PLACE the synchroscope switch for the 4-kV shutdown board Critical Step feeder breaker that is to be paralleled with the Diesel Generator in ON. SAT Standard: UNSAT Places Synchroscope switch for 4-kV Shutdown Board EC normal N/A feeder breaker 1338 to ON Step 4:
[4] CHECK the applicable 4-kV unit board (4-kV bus tie board)
SAT voltage is between 3950 VOLTS and 4400 VOLTS and NOT undergoing abnormal voltage transients.
UNSAT Standard:
N/A Verifies 4-kV Unit Board voltage is between 3950 Volts and 4400 Volts and NOT undergoing abnormal voltage transients.
Step 5:
[5] VERIFY associated incoming frequency is between 59 HERTZ and 61 HERTZ and NOT undergoing abnormal frequency transients.
Shutdown Instrument Name Instrument No. Panel SAT Bd 3EA or GEN SYNC 3-SI-82-3AB 3-9-23 UNSAT 3EB FREQUENCY 3EC or GEN SYNC 3-SI-82-3CD 3-9-23 N/A 3ED FREQUENCY Standard:
Verifies incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients using GEN SYNC FREQUENCY, 3-SI-82-CD .
6
STEP / STANDARD SAT /
UNSAT Step 6:
CAUTION DO NOT parallel the Diesel Generators with an unstable offsite source or during inclement weather (e.g., lightning, heavy winds). SAT UNSAT
[6] IF 4-kV unit board (4-kV bus tie board) is experiencing abnormal voltage or frequency conditions, THEN PERFORM the following: N/A Standard:
N/A Step 7:
CAUTION Only one Unit 1 and 2 Diesel Generator at a time is allowed to be operated in parallel with system.
Critical Step
[7] PULL and PLACE the associated Diesel Generator mode SAT selector switch in PARALLELED WITH SYSTEM.
UNSAT Diesel Handswitch Name Handswitch Panel No.
N/A 3C DG 3C MODE SELECT 3-HS-82-3C/5A 3-9-23 Standard:
Pulls DG 3C MODE SELECT switch 3-HS-82-3C/5A and places it in PARALLELED WITH SYSTEM 7
STEP / STANDARD SAT /
UNSAT Step 8:
CAUTION Failure of the PARALLELED WITH SYSTEM light to illuminate in the following step could indicate that the DG is still in SINGLE UNIT operation and result in overload when the DG output breaker is closed. SAT UNSAT
[8] RELEASE the Diesel Generator mode selector switch and OBSERVE PARALLELED WITH SYSTEM light illuminated. N/A Standard:
Releases the Diesel Generator 3C mode selector switch, 3-HS-82-3C/5C and observes PARALLELED WITH SYSTEM light is illuminated.
Step 9:
[9] ADJUST Diesel Generator frequency using the associated Diesel Generator governor control switch to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction.
Critical Step Diesel Handswitch Name Handswitch Panel No. SAT 3C DG 3C GOVERNOR 3-HS-82-3C/3A 3-9-23 CONTROL UNSAT Standard: N/A Adjusts Diesel Generator 3C frequency using Diesel Generator governor control switch, 3-HS-82-3C/3A (in lower direction) to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction.
8
STEP / STANDARD SAT /
UNSAT Step 10:
[10] USE the associated Diesel Generator voltage regulator control switch to match Diesel Generator and System voltages.
Dies Instrument Name Inst No. Panel el SAT DG 3C VOLT REGULATOR 3-HS CONT 3C/2A UNSAT 3C GEN SYNC REF VOLTAGE 3-EI-82-3CD 3-9-23 SYSTEM SYNC REF 3-EI-211-VOLTAGE 3ECB/B N/A Standard:
Matches DG C voltage with system voltage using DG 3C VOLT REGULATOR CONT switch 3-HS-82-3C/2A Step 11:
[11] WHEN the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position, THEN Critical Step CLOSE the 4-kV shutdown board feeder breaker that is to be SAT paralleled with the Diesel Generator.
UNSAT Standard:
N/A Closes the 4-kV shutdown board normal feeder breaker 1338 when the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position.
Step 12:
[12] PLACE the synchroscope switch for the 4-kV shutdown board SAT feeder breaker that was paralleled with the Diesel Generator in OFF. UNSAT Standard: N/A Places the synchroscope switch for BKR 1338 in OFF 9
STEP / STANDARD SAT /
UNSAT Step 13:
[13] IF the normal feeder breaker is supplying the 4-kV shutdown board, THEN RESET the associated 4kV shutdown board auto transfer lockout Critical Step relay.
SAT Diesel Handswitch Name Handswitch Panel No.
UNSAT 3C 4KV SD BD 3EC 3-43-211-3EC 3-9-23 AUTO/LOCKOUT N/A RESET Standard:
Resets 4KV SD BD 3EC Auto Transfer Lockout Relay Step 14:
NOTE If diesel operates greater than 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> at less than 50% load, the diesel should be loaded to full load for at least 30 minutes prior to engine shutdown. This will allow the engine to clean out any oil accumulations from the exhaust manifolds.
[14] IF DG has been operating at a low-load condition (50%) for an extended period of time (4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br />) THEN PERFORM the following (Otherwise N/A): Critical Step
[14.1] USE the associated Diesel Generators governor control SAT switch and voltage regulator control switch to INCREASE kW and kVAR load, in increments of 100kW every 15 UNSAT minutes.
N/A Diesel Handswitch Name Hands Panel witch No.
DG 3C GOVERNOR CONTROL 3-HS-82-3C/3A 3C 3-9-23 DG 3C VOLT REGULATOR 3-HS-CONTROL 82-3C/2A 10
STEP / STANDARD SAT /
UNSAT Step 14 continued:
[14.2] OBSERVE the exhaust stack smoke concentration from outside the DG room after each incremental increase.
[14.3] STEP N/A
[14.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible.
[14.5] MAINTAIN 100% load for a minimum of 30 minutes.
Standard:
Loads DG to 2600 kW and 1850 kVAR by using 0-HS-82-A/3A and 0-HS-82-A/2A handswitches.
CUE: After first 100 kW load adjustment state 15 minutes have elapsed and no observable black smoke from exhaust stack for time compression and continue to full load.
Step 15:
NOTE VARs lagging should be maintained when adjusting kW load (rising or lowering). This may require kW load adjustment to be stopped periodically to allow for adjusting kVAR load. Once desired kW load is achieved, Illustration 1 should be referred to for determination of kVAR loading required to obtain a power factor (pf) of 0.8 lagging. Diesel generator kVAR load should then be adjusted to obtain a 0.8 pf lagging. IF system conditions will NOT permit the kVAR loading required to obtain a 0.8 pf lagging, kVAR load should be adjusted to SAT the maximum kVAR lagging the system will allow.
UNSAT
[15] USE the associated Diesel Generator's governor control switch N/A and voltage regulator control switch to obtain desired kW and kVAR load.
Diesel Handswitch Name Handswitch No. Panel DG 3C GOVERNOR 3-HS CONTROL 3C/3A 3C 3-9-23 DG 3C VOLT REGULATOR 3-HS CONT 3C/2A 11
STEP / STANDARD SAT /
UNSAT Standard:
Obtains desired kW and kVAR load using DG 3C Governor Control switch, 3-HS-82-3C/3A and DG Volt Regulator Control switch, 3-HS-82-3C/2A CUE: state 30 minutes have elapsed continue with procedure.
Step 16:
[16] MONITOR the offsite source that is paralleled with the Diesel Generator. SAT
[17] IF abnormal voltage or frequency transients are experienced, UNSAT THEN N/A Standard:
Step is N/A Step 17:
[18] WHEN Parallel with System operation is no longer desired, THEN UNLOAD the Diesel Generator as follows:
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVAR limit may result in a reverse power trip of the Diesel Generator output breaker. Critical Step SAT
[18.1] USE the associated Diesel Generator's governor control switch and voltage regulator control switch to reduce UNSAT generator load to approximately 300 kW and 250 kVAR: N/A Diesel Instrument Name Inst No. Panel DG 3C GOVERNOR CONTROL 3-HS-82-3C/3A DG 3C VOLT REGULATOR 3-HS-82-3C/2A 3C 3-9-23 CONT DG 3C KILOWATTS 3-JI-82-3C/A DG 3C KILOVARS 3-VAR-82-3C/A 12
STEP / STANDARD SAT /
UNSAT Step 17 continued:
Standard:
Unloads the DG to approximately 300 KW and 250 kVAR Step 18:
[18.2] PLACE the associated Diesel Generator breaker control Critical Step switch in TRIP.
SAT Diesel Handswitch Name Handswitch No. Panel 3C DG 3C BKR 1832 3-HS-211- 3-9-23 UNSAT 3EC/10A N/A Standard:
Trips breaker DG 3C BKR 1832 Step 19:
[18.3] PULL and PLACE the associated Diesel Generator mode Critical Step selector switch in SINGLE UNIT.
SAT Diesel Handswitch Name Handswitch No. Panel 3C DG 3C MODE SELECT 3-HS-82-3C/5A 0-9-23 UNSAT Standard: N/A Pulls and places 3-HS-82-3C/5A to Single Unit Step 20: SAT
[18.4] RELEASE the Diesel Generator mode selector switch and UNSAT OBSERVE the SINGLE UNIT light illuminated.
N/A Standard:
Verifies Single Unit light illuminated CUE: ANOTHER OPERATOR WILL CONTINUE FROM HERE STOP TIME END OF TASK 13
Provide to Applicant INITIAL CONDITIONS:
You are an Operator on Unit 3.
- No Inclement weather currently exists in the area
- 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> ago, 4 KV Shutdown Board 3EC was separated from Offsite Power in accordance with 3-OI-82, Standby Diesel Generator System.
INITIATING CUE:
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board 3EC using the normal feeder breaker and remove DG 3C from parallel operation in accordance with 3-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23.
14
SITE: BFN JPM TITLE: Respond to Off-Gas Post Treatment Radiation HI-HI-HI JPM NUMBER: 190 U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-066-AB-02 -Respond to Off-Gas Post Treatment TASK NUMBER / TASK TITLE(S):
Radiation Hi-Hi-Hi K/A RATINGS: RO 2.9 SRO 3.2 271000 Offgas System: A2.16; Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those K/A STATEMENT: predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2)
RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: N/A TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: 190 U2 RO SRO DATE: _______
TASK STANDARD: Respond to Off-Gas Post Treatment Radiation HI-HI-HI per 2-AOI-66-2 and/or 2-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-66-2, 2-ARP-9-4C/35 VALIDATION TIME: 15 Minutes PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 287
- 1. Reset to IC 28 Console 2. Fire Manual Trigger 2 Operator 3. Fire Manual Trigger 1 Instructions 4. Station 2nd operator to respond to alarms Malfunctions Description Event Severity Delay Initial set TH23 FUEL CLADDING 1 50 N/A YES DAMAGE RM14C OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURERM 265A RM14D OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-266A Remotes Description Event Severity Delay Initial set OG06 Bypass FCV-66-28 2 N/A N/A BYP Post Treatment Hi-Hi-Hi Rad Isol Overrides Description Event Severity Delay Initial set ZAORI9014A RX BLDG AREA 1 2.5 N/A YES RAD ZAORI9017A RX BLDG AREA 1 2.6 N/A YES RAD ZAORM90265A 90-265 METER 1 6.0 N/A YES UPSCALE ZAORM90266A 90-266 METER 1 6.0 N/A YES UPSCALE ZAORR90135R1 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90135R2 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZLORM90265A_1 90-265 DRAW LITE 1 N/A N/A YES 3
ZLORM90265A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_4 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_4 90-265 DRAW LITE 1 N/A N/A YES XA553A5 OG PRETREAT 1 N/A N/A YES RAD HI XA553A6 STACK GAS RAD 1 N/A N/A YES HI HI XA553A7 MSL RAD HI 1 N/A N/A YES XA553A13 STACK GAS RAD 1 N/A N/A YES HI XA553A27 MSL RAD HI HI 1 N/A N/A YES XA554C26 CARBON BED 1 N/A N/A YES VAULT RAD HI XA554C27 OG ANNUAL 1 N/A N/A YES RELEASE LIMIT EXCEEDED XA554C33 OG POST TREAT 1 N/A N/A YES RAD HI XA554C34 OG POST TREAT 1 N/A N/A YES RAD HI HI XA554C35 OG POST TREAT 1 N/A N/A YES RAD HI HIHI ZDIHS6628 66-28 VALVE 1 N/A N/A YES CLOSED ZAORR90265R1 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90265R2 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZAORR90160R1 OG PRETREAT 1 -2.0 N/A YES RECORDER UPSCALE XA554B2 RWCU FILTER 1 N/A N/A YES INLET CNDT HIGH Schedule File(s): JPM 190 U2 OG Post treat Rad HI HIHI 4
IN-SIMULATOR:
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are the Unit 2 Operator. Unit 2 is at 100% power.
INITIATING CUE:
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 2-XA-55-4C, window 35.
5
START TIME STEP / STANDARD SAT / UNSAT Performance Step 1:
SAT When directed, identify/obtain copy of ARP-9-4C, window 35.
UNSAT Standard:
N/A Obtains copy of 2-ARP-9-4C, window 35 Examiner Note: Candidate may recognize the annunciator as an entry condition and go directly to 2-AOI-66-2. In that event, continue at Performance Step 5.
Performance Step 2:
2-ARP-9-4C window 35 Operator Action:
A. VERIFY alarm condition on the following
- OFFGAS POST-TREATMENT RADIATION recorder, SAT 2-RR-90-265 on Panel 2-9-2.
- OG POST-TREATMENT CHAN A RAD MON RTMR UNSAT radiationmonitor, 2-RM-90-266A on Panel 2-9-10.
- OG POST-TREATMENT CHAN B RAD MON RTMR N/A radiationmonitor, 2-RM-90-265A on Panel 2-9-10.
Standard:
Verified alarm condition on 2-RR-90-265 and 2-RM-265/266.
Performance Step 3:
B. VERIFY OFF-GAS SYSTEM ISOLATION VALVE, 2-FCV- Critical Step 66-28 has the Mechanical Restraint DISENGAGED and 2-FCV-66-28 isCLOSED. SAT Standard: UNSAT Takes handswitch 2-FCV-66-28 to close and observes green light N/A illuminated and red light out.
Cue: If asked, the Offgas Isolation Valve, 2-FCV-66-28 is NOT mechanically restrained.
6
STEP / STANDARD SAT / UNSAT Performance Step 4:
C. REFER to 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-SAT Hi-Hi UNSAT Standard:
N/A Refers to 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 5:
2-AOI-66-2 4.0 OPERATOR ACTIONS 4.1 Immediate Actions Critical Step
[1] IF scram has not occurred, THEN SAT PERFORM the following:
UNSAT
[1.1] IF core flow is above 60%, THEN N/A REDUCE core flow to between 50-60%.
Standard:
Reduced core flow to between 50-60% with recirc system.
Performance Step 6:
[1.2] MANUALLY SCRAM the Reactor. (Reference 2-AOI-100-1).
Standard:
Critical Step
- Depresses both SCRAM Pushbuttons
- Places mode switch in shutdown SAT
- Verifies All Rods in
- Performs a Scram Announcement UNSAT o Rx Mode Switch Position: Shutdown N/A o Rod Position: All Full In o Reactor Water Level ____ & Trend ___
o Reactor Pressure ____ & Trend ___
o MSIV Position: OPEN o Rx Power: <5%
Examiner Note: The scram report and referring to 2-AOI-100-1 are not considered critical.
7
STEP / STANDARD SAT / UNSAT CUE: Proceed with subsequent actions of 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 7:
4.2 Subsequent Actions
[1] IF OFFGAS SYSTEM ISOLATION VALVE, 2-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN SAT DISENGAGE 2-FCV-066-0028 mechanical restraint by UNSAT rotating the restraining handwheel fully in the counterclockwisedirection, locally at the Stack. (Otherwise N/A N/A)
Standard:
Verifies that 2-FCV-066-0028 in NOT mechanically restrained.
Cue: 2-FCV-066 is NOT mechanically restrained.
Performance Step 8:
[2] VERIFY CLOSED OFFGAS SYSTEM ISOLATION VALVE, Critical Step 2-FCV-66-28 on Panel 2-9-53 or locally.
SAT Standard:
UNSAT Verifies 2-FCV-66-28 is closed at panel 9-53 by Verifying RED light above handswitch extinguished and GREEN light above N/A handswitch illuminated. (May have already verified valve closed from the ARP).
Examiner Note: May have already verified valve closed from the ARP Performance Step 9:
[3] MONITOR area radiation levels at Panel: 2-9-11. SAT Standard: UNSAT Monitored radiation levels at Panel 9-11. N/A Cue: Another operator will monitor and evaluate Area Radiation Levels.
8
STEP / STANDARD SAT / UNSAT Performance Step 10:
[4] REFER TO EPIP-1 for emergency classification level and SAT response.
UNSAT Standard; N/A Notifies SM to implement EPIP-1.
Cue: The Shift Manager is implementing the EPIPs as needed.
Performance Step 11:
[5] MONITOR the following parameters:
A. MAIN STEAM LINE RADIATION, 2-RR-90-135, Panel 2-9-2.
B. OFFGAS PRETREATMENT RADIATION 2-RR 157, Pnl 2-9-2. SAT C. OFFGAS POST-TREATMENT RADIATION 2RR- UNSAT 90-265, Pnl 2-9-2 N/A D. STACK GAS RADIATION, 0-RR-90-147, Unit 1 Panel 1-9-2.
Standard; Monitors90-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147.
Cue: As Unit 1 Operator, Stack Gas Radiation, 0-RR-90-147 is reading 5X10E6 cps.
9
STEP / STANDARD SAT / UNSAT Performance Step 12:
[6] IF after five minutes from scram the Offgas Post Treatment activity is not less than 6 x 10E5 cps as indicated on OFFGASRADIATION recorder 2-RR-90-266 on panel 2 Critical Step 2, THEN SAT CLOSE all Main Steam Isolation Valves and Main Steam LineDrain Valves, 2-FCV-1-55 and 2-FCV-1-56.
UNSAT Standard:
N/A Recognizes that the Off-Gas Post Treatment activity is >6 X 10E5 and closes all Main Steam Isolation Valves and Main Steam Line Drain Valves (2-FCV-1-55/56)
Cue: The Unit has been scrammed for 5 minutes.
- Acknowledge closing of MSIVs.
Examiner Note: Closing 1-55 and 1-56 is not considered critical.
Performance Step 13:
NOTE Placing additional Stack Dilution Air Fans in service should keep 0-RM-90-147and 0-RM-90-148 on scale.
[7] PLACE STACK DILUTION FAN SEL control switch, SAT 2-XS-66-29, Panel 2-9-8, in OFF.
UNSAT
[8] START standby STACK DILUTION FAN 2B(2A) using controlswitch, 2-HS-66-31A(29A), Panel 2-9-8. N/A Standard:
Places 2-XS-66-29 in OFF and Starts standby Stack Dilution fan 2B, using 2-HS-66-31A Cue: That completes this task.
STOP TIME _______
END OF TASK 10
Provide to Applicant IN-SIMULATOR:
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are the Unit 2 Operator. Unit 2 is at 100% power.
INITIATING CUE:
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 2-XA-55-4C, window 35.
11
SITE: BFN JPM TITLE: Respond to Off-Gas Post Treatment Radiation HI-HI-HI JPM NUMBER: 190 U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-066-AB-02 -Respond to Off-Gas Post Treatment TASK NUMBER / TASK TITLE(S):
Radiation Hi-Hi-Hi K/A RATINGS: RO 2.9 SRO 3.2 271000 Offgas System: A2.16;Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the K/A STATEMENT:
consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2)
RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: N/A TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: 190 RO SRO DATE: _______
TASK STANDARD: Respond to Off-Gas Post Treatment Radiation HI-HI-HI per 3-AOI-66-2 and/or 3-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: 3-AOI-66-2, 3-ARP-9-4C/35 VALIDATION TIME: 15 Minutes PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 288
- 1. Reset to IC 28 Console 2. Fire Manual Trigger 2 Operator 3. Fire Manual Trigger 1 Instructions 4. Station 2nd operator to respond to alarms Malfunctions Description Event Severity Delay Initial set TH23 FUEL CLADDING 1 50 N/A YES DAMAGE RM14C OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-265A RM14D OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-266A Remotes Description Event Severity Delay Initial set OG06 Bypass FCV-66-28 2 N/A N/A BYP Post Treatment Hi-Hi-Hi Rad Isol Overrides Description Event Severity Delay Initial set ZAORI9014A RX BLDG AREA 1 2.5 N/A YES RAD ZAORI9017A RX BLDG AREA 1 2.6 N/A YES RAD ZAORM90265A 90-265 METER 1 6.0 N/A YES UPSCALE ZAORM90266A 90-266 METER 1 6.0 N/A YES UPSCALE ZAORR90135R1 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90135R2 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZLORM90265A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_2 90-265 DRAW LITE 1 N/A N/A YES 3
ZLORM90265A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_4 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_4 90-265 DRAW LITE 1 N/A N/A YES XA553A5 OG PRETREAT 1 N/A N/A YES RAD HI XA553A6 STACK GAS RAD 1 N/A N/A YES HI HI XA553A7 MSL RAD HI 1 N/A N/A YES XA553A13 STACK GAS RAD 1 N/A N/A YES HI XA553A27 MSL RAD HI HI 1 N/A N/A YES XA554C26 CARBON BED 1 N/A N/A YES VAULT RAD HI XA554C27 OG ANNUAL 1 N/A N/A YES RELEASE LIMIT EXCEEDED XA554C33 OG POST TREAT 1 N/A N/A YES RAD HI XA554C34 OG POST TREAT 1 N/A N/A YES RAD HI HI XA554C35 OG POST TREAT 1 N/A N/A YES RAD HI HIHI ZDIHS6628 66-28 VALVE 1 N/A N/A YES CLOSED ZAORR90265R1 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90265R2 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZAORR90160R1 OG PRETREAT 1 -2.0 N/A YES RECORDER UPSCALE XA554B2 RWCU FILTER 1 N/A N/A YES INLET CNDT HIGH Schedule File(s): JPM 190 U3 OG Post treat Rad HI HIHI 4
IN-SIMULATOR:
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are the Unit 3 Operator. Unit 3 is at 100% power.
INITIATING CUE:
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 3-XA-55-4C, window 35.
5
START TIME STEP / STANDARD SAT / UNSAT Performance Step 1:
SAT When directed, identify/obtain copy of ARP-9-4C, window 35.
UNSAT Standard:
N/A Obtains copy of 3-ARP-9-4C, window 35 Examiner Note: Candidate may recognize the annunciator as an entry condition and go directly to 3-AOI-66-2. In that event, continue at Performance Step 5.
Performance Step 2:
3-ARP-9-4C window 35 Operator Action:
A. VERIFY alarm condition on the following
- OFFGAS POST-TREATMENT RADIATION recorder, SAT 3-RR-90-265 on Panel 3-9-2.
- OG POST-TREATMENT CHAN A RAD MON RTMR UNSAT radiationmonitor, 3-RM-90-266A on Panel 3-9-10.
- OG POST-TREATMENT CHAN B RAD MON RTMR N/A radiationmonitor, 3-RM-90-265A on Panel 3-9-10.
Standard:
Verified alarm condition on 3-RR-90-265 and 3-RM-265/266.
Performance Step 3:
B. VERIFY OFF-GAS SYSTEM ISOLATION VALVE, 3-FCV- Critical Step 66-28 has the Mechanical Restraint DISENGAGED and 3-FCV-66-28 isCLOSED. SAT Standard: UNSAT Takes handswitch 3-FCV-66-28 to close and observes green light N/A illuminated and red light out.
Cue: If asked, the Offgas Isolation Valve, 3-FCV-66-28 is NOT mechanically restrained.
6
STEP / STANDARD SAT / UNSAT Performance Step 4:
C. REFER to 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi SAT Standard: UNSAT Refers to 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi N/A Performance Step 5:
3-AOI-66-2 4.0 OPERATOR ACTIONS 4.1 Immediate Actions Critical Step
[1] IF scram has not occurred, THEN SAT PERFORM the following:
UNSAT
[1.1] IF core flow is above 60%, THEN N/A REDUCE core flow to between 50-60%.
Standard:
Reduced core flow to between 50-60% with recirc system.
Performance Step 6:
[1.2] MANUALLY SCRAM the Reactor. (Reference 3-AOI-100-1).
Standard:
Critical Step
- Depresses both SCRAM Pushbuttons
- Places mode switch in shutdown SAT
- Verifies All Rods in
- Performs a Scram Announcement UNSAT o Rx Mode Switch Position: Shutdown N/A o Rod Position: All Full In o Reactor Water Level ____ & Trend ___
o Reactor Pressure ____ & Trend ___
o MSIV Position: OPEN o Rx Power: <5%
Examiner Note: The scram report and referring to 3-AOI-100-1 are not considered critical.
7
STEP / STANDARD SAT / UNSAT CUE: Proceed with subsequent actions of 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 7:
4.2 Subsequent Actions
[1] IF OFFGAS SYSTEM ISOLATION VALVE, 3-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN SAT DISENGAGE3-FCV-066-0028 mechanical restraint by UNSAT rotating the restraining handwheel fully in the counterclockwisedirection, locally at the Stack. (Otherwise N/A N/A)
Standard:
Verifies that 3-FCV-066-0028 in NOT mechanically restrained.
Cue: 3-FCV-066 is NOT mechanically restrained.
Performance Step 8:
[2] VERIFY CLOSED OFFGAS SYSTEM ISOLATION VALVE, Critical Step 3-FCV-66-28 on Panel 3-9-53 or locally.
SAT Standard:
UNSAT Verifies 3-FCV-66-28 is closed at panel 9-53 by Verifying RED light above handswitch extinguished and GREEN light above N/A handswitch illuminated. (May have already verified valve closed from the ARP).
Examiner Note: May have already verified valve closed from the ARP Performance Step 9:
[3] MONITOR area radiation levels at Panel: 3-9-11.
UNSAT Standard:
N/A Monitored radiation levels at Panel 9-11.
Cue: Another operator will monitor and evaluate Area Radiation Levels.
8
STEP / STANDARD SAT / UNSAT Performance Step 10:
[4] REFER TO EPIP-1 for emergency classification level and SAT response.
UNSAT Standard; N/A Notifies SM to implement EPIP-1.
Cue: The Shift Manager is implementing the EPIPs as needed.
Performance Step 11:
[5] MONITOR the following parameters:
A. MAIN STEAM LINE RADIATION, 3-RR-90-135, Panel 3-9-2.
B. OFFGAS PRETREATMENT RADIATION 3-RR 157, Pnl3-9-2. SAT C. OFFGAS POST-TREATMENT RADIATION 3-RR- UNSAT 90-265, Pnl3-9-2 N/A D. STACK GAS RADIATION, 0-RR-90-147, Unit 1 Panel 1-9-2.
Standard; Monitors90-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147.
Cue: As Unit 1 Operator, Stack Gas Radiation, 0-RR-90-147 is reading 5X10E6 cps.
9
STEP / STANDARD SAT / UNSAT Performance Step 12:
[6] IF after five minutes from scram the Offgas Post Treatment activity is not less than 6 x 10E5 cps as indicated on OFFGASRADIATION recorder 3-RR-90-265 on panel 3 2, THEN Critical Step CLOSE all Main Steam Isolation Valves and Main Steam SAT LineDrain Valves, 3-FCV-1-55 and 3-FCV-1-56.
UNSAT Standard:
N/A Recognizes that the Off-Gas Post Treatment activity is >6 X 10E5 and closes all Main Steam Isolation Valves and Main Steam Line Drain Valves (3-FCV-1-55/56)
Cue: The Unit has been scrammed for 5 minutes.
- Acknowledge closing of MSIVs.
Examiner Note: Closing 1-55 and 1-56 is not considered critical.
Performance Step 13:
NOTE Placing additional Stack Dilution Air Fans in service should keep 0-RM-90-147and 0-RM-90-148 on scale.
[7] PLACE STACK DILUTION FAN SEL control switch, SAT 3-XS-66-29, Panel 3-9-8, in OFF.
UNSAT
[8] START standby STACK DILUTION FAN 3B(3A) using controlswitch, 3-HS-66-31A(29A), Panel 3-9-8. N/A Standard:
Places 3-XS-66-29 in OFF and Starts standby Stack Dilution fan 3B, using 3-HS-66-31A Cue: That completes this task.
STOP TIME ________
END OF TASK 10
Provide to Applicant IN-SIMULATOR:
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are the Unit 3 Operator. Unit 3 is at 100% power.
INITIATING CUE:
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 3-XA-55-4C, window 35.
11
SITE: BFN JPM TITLE: AUTOMATIC START FAILURE OF A & C FIRE PUMPS JPM NUMBER: 673 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-026-NO-01/ MONITOR AUTO START OF FIRE TASK NUMBER / TASK TITLE(S):
PUMP K/A RATINGS: RO: 3.4 SRO: 3.4 286000 Fire Protection System A2.08; Ability to (a) predict the impacts of the following on the FIRE PROTECTION SYSTEM; K/A No. &STATEMENT: and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Failure to actuate when required RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 8 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _673A___
TASK STANDARD: Perform operations necessary to manually start A, B and C Fire Pumps.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 0-OI-26 VALIDATIONTIME:__15 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 04/28/15 All Initial issue 3
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 1.
- The Reactor Power at 70%
- A Fire Exists on B Reactor Feed Pump Lube Oil Reservoir.
- Fire OPS has been dispatched to the scene.
- Fire Pump B Tagged Out for Maintenance
- A and C Fire Pumps failed to Auto Start.
INITIATING CUES:
The US directs you to start A and C Electric Fire Pumps per 0-OI-26 section 5.4.
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
4
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
[1] PLACE the FIRE PUMP A TRANSFER switch, 0-XS-26-1 in EMERGENCY position, at the respective switchgear.
Critical Step Pump Board Compt A 4160V Shutdown Bd A 11 SAT C 4160V Shutdown Bd C 10 UNSAT Standard:
N/A Simulates placing FIRE PUMP A TRANSFER switch 0-XS-26-3 in EMERGENCY position at 4160 Shutdown Board A, Compartment 11 CUE: FIRE PUMP A TRANSFER switch 0-XS-26-1 is in the EMERGENCY position Step 2:
Critical Step
[2] CLOSE the breaker by placing the FIRE PUMP A CONTROL switch, 0-HS-26-1C to CLOSE. SAT Standard: UNSAT Simulates placing FIRE PUMP A CONTROL switch, 0-HS-26-1C N/A to CLOSE position.
CUE: Breaker Red indicating light is ON with Green and Amber lights are OFF.
Breaker Flag indicates CLOSED with Charging Spring indicating CHARGED.
Step 3:
[3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. SAT Standard UNSAT VERIFIES pump ammeter at breaker indicates between 25 and N/A 40 amps.
CUE: FIRE PUMP A ammeter at breaker indicates 30 amps.
5
Step 4:
[4] PLACE the NORM/EMERG Switch in NORMAL.
SAT Standard UNSAT PLACES the NORM/EMERG Switch in NORMAL for FIRE N/A PUMP A.
CUE: FIRE PUMP A NORM/EMERG Switch is in NORMAL Step 5:
[1] PLACE the FIRE PUMP C TRANSFER switch, 0-XS-26-3 in EMERGENCY position, at the respective switchgear.
Critical Step Pump Board Compt A 4160V Shutdown Bd A 11 SAT C 4160V Shutdown Bd C 10 UNSAT Standard:
N/A Simulates placing FIRE PUMP C TRANSFER switch 0-XS-26-3 in EMERGENCY position at 4160 Shutdown Board C, Compartment 10 CUE: FIRE PUMP C TRANSFER switch 0-XS-26-3 is in the EMERGENCY position Step 5:
Critical Step
[2] CLOSE the breaker by placing the FIRE PUMP C CONTROL switch, 0-HS-26-3C to CLOSE.
SAT Standard:
UNSAT Simulates placing FIRE PUMP C CONTROL switch, 0-HS-26-3C N/A to CLOSE position.
CUE: Breaker Red indicating light is ON with Green and Amber lights are OFF.
Breaker Flag indicates CLOSED with Charging Spring indicating CHARGED.
6
Step 6:
[3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. SAT Standard UNSAT VERIFIES pump ammeter at breaker indicates between 25 and N/A 40 amps.
CUE: FIRE PUMP C ammeter at breaker indicates 30 amps.
Step 7:
[4] PLACE the NORM/EMERG Switch in NORMAL.
SAT Standard UNSAT PLACES the NORM/EMERG Switch in NORMAL for FIRE N/A PUMP C.
CUE: FIRE PUMP C NORM/EMERG Switch is in NORMAL and this completes the JPM.
Termination Criteria: When two Fire Pumps are in service the JPM is complete.
STOP TIME:
7
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 1.
- The Reactor Power at 70%
- A Fire Exists on B Reactor Feed Pump Lube Oil Reservoir.
- Fire OPS has been dispatched to the scene.
- Fire Pump B Tagged Out for Maintenance
- A and C Fire Pumps failed to Auto Start.
INITIATING CUES:
The US directs you to start A and C Electric Fire Pumps per 0-OI-26 section 5.2.
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
8
ALIGNING EMERGENCY EECW MAKEUP TO SPENT SITE: BFN JPM TITLE:
FUEL POOL JPM NUMBER: 674 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-95/ Make-Up To SFP By EECW With TASK NUMBER / TASK TITLE(S):
Fire Hose (Internal Make-Up)
K/A RATINGS: RO: 3.1 SRO: 3.3 233000 Fuel Pool Cooling and Clean-up; A2.02; Ability to (a) predict the impacts of the following on the FUEL POOL COOLING AND CLEAN-UP ; and (b) based on those K/A No. &STATEMENT:
predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Low pool level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: __674__
TASK STANDARD: Perform operations necessary to align either North or South Headers of EECW to Unit 2 Spent Fuel Pool.
Operator Fundamental evaluated:
OF-2 Controlling plant evolutions and indications closely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-78-1 VALIDATION TIME: 25 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 3
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is in cold shutdown
- The Unit 2 Spent Fuel Pool water level is lowering.
- Fire Protection is available to assist INITIATING CUES:
The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3].
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
4
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
NOTES
- 1) Hose straps are staged at the hoses at the following locations:
- Unit 1/Unit 2 Reactor Bldg Stairwell, El. 621, R6 U Line (placed on hose to carry weight of charged hose lines).
- Hose reel on the Refuel Floor, El. 664, R6 U Line (for use in securing hose ends as needed).
- 2) Additional hose is stored in a cabinet located in Unit 1/Unit 2 Elevator Room, Reactor Bldg, El 595.
Critical Step CAUTION Performance of this attachment will degrade water chemistry in the SAT Spent Fuel Pool.
UNSAT
[3] UNLOCK and OPEN the following valves:
N/A
- NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792.
- SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793.
Standard:
Simulates opening NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792 and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793 by demonstrating opening each valve counter-clockwise and breaking seal.
CUE: NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793 is OPEN Located in stairwell between elevation 565 ft and 593 ft. Hoses are already connected, no tools required.
5
STEP / STANDARD SAT / UNSAT Step 3:
[4] VERIFY charged hoses in stairwell are not obstructing stairway access and/or kinked.
[4.1] ADJUST hose straps, as necessary.
UNSAT Standard:
N/A VERIFIES hoses in stairwell are not kinked Note to Examiner: Hoses are already run along the stairwell. Applicant should verify hoses not kinked and connected.
Step 4:
[5] VERIFY hose connected from NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and route to Unit 2 Spent Fuel Pool Critical Step (El 664, Refuel Floor, R6-U Line).
SAT Standard:
UNSAT VERIFY hose connected from NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and route to Unit 2 Spent N/A Fuel Pool (El 664, Refuel Floor, R6-U Line).
Note to Examiner: Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. Hoses are already connected, no tools required.
Location: Refuel Floor Elevation 664 ft, R U Line.
Step 5:
[6] VERIFY hose connected from SOUTH HDR SPLY TO EMER Critical Step FUEL POOL MU, 1-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664, Refuel Floor, R6-U Line)
SAT Standard:
UNSAT VERIFY hose connected from SOUTH HDR SPLY TO EMER N/A FUEL POOL MU, 1-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664, Refuel Floor, R6-U Line) 6
STEP / STANDARD SAT / UNSAT Note to Examiner: Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. Hoses are already connected, no tools required.
Location: Refuel Floor Elevation 664 ft, R U Line.
Step 6:
[7] VERIFY OPEN the following valves (El 664, Refuel Floor, R6 U Line):
- NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-Critical Step 0796.
- SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797.
UNSAT Standard:
N/A Simulates opening NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797 by demonstrating opening each valve counter-clockwise.
CUE: NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797 is OPEN Location: Refuel Floor Elevation 664 ft, R U Line.
Step 7:
[8] VERIFY charged hoses on the Refuel Floor are not kinked.
SAT Standard: UNSAT VERIFY charged hoses on the Refuel Floor are not kinked N/A Termination Criteria: NORTH and SOUTH Header are aligned then the JPM is complete. State another operator will perform the remaining steps.
STOP TIME:
7
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is in cold shutdown
- The Unit 2 Spent Fuel Pool water level is lowering.
- Fire Protection is available to assist INITIATING CUES:
The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3].
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
8
START UP AND SYNCHRONIZE UNIT 3 PREFERRED SITE: BFN JPM TITLE:
MMG SET JPM NUMBER: 307 REVISION: 6 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): S-57C-NO-04 K/A RATINGS: RO: 2.5 SRO: 2.9 262002 Uninterruptable Power Supply (A.C./D.C.) A1.02; Ability to predict and/or monitor changes in parameters associated with K/A No. &STATEMENT:
operating the UNINTERRUPTABLE POWER SUPPLY (A.C./D.C.) controls including: Motor generator outputs RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 6 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _307___
TASK STANDARD: Perform operations necessary to Start-up and synchronize Unit Preferred MMG Set Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant Evolutions Precisely PRA: NA REFERENCES/PROCEDURES NEEDED: 0-OI-57C VALIDATIONTIME: 25 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 1 10/26/94 ALL GENERAL REVISION 2 05/07/95 ALL GENERAL REVISION FORMAT, PROCEDURE REVISION, ADDED 3 10/15/97 ALL PLANT WORK EXPECTATIONS TOUCH STAAR, SAFETY, AND 3-WAY COMM.
PROCEDURE REVISION, FORMAT 4 11/10/99 ALL DOCUMENT 5 10/03/01 ALL PROCEDURE REVISION 6 04/28/15 ALL UPDATE TO NEW FORMAT 3
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is in cold shutdown
- The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1.
- Maintenance has been completed on the Unit 3 Unit Preferred MMG Set.
INITIATING CUES:
The SM directs you to start up and synchronize the Unit 3 Unit Preferred MMG Set as directed by 0-OI-57C per section 5.5 step 5.5[16].
NOTE: PERFORMER WILL NEED GGMKA KEY.
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
4
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
NOTE Steps 5.5[16] through 5.5[26] are performed from Battery Board Room 2 UNIT PFD Sync. & Speed Control Panel. Critical Step SAT
[16] PLACE UNIT 3 MMG OPERATING MODE, 3-HS-252-02AB in AUTO.
UNSAT Standard:
N/A VERIFIED/SIMULATED PLACING the Unit 3 MMG SET OPERATING MODE 3-HS-252-02AB in AUTO.
Cue: The Unit 3 MMG SET OPERATING MODE 3-HS-252-02AB is in AUTO position.
Step 2:
Critical Step
[17] PLACE UNIT 3 MMG LOCAL-REMOTE CONTROL, 3-XS-252-02A in REMOTE.
SAT Standard:
UNSAT SIMULATED PLACING the Unit 3 MMG SET LOCAL-REMOTE N/A CONTROL 3-XS-252-02A in the REMOTE position.
Cue: The Unit 3 MMG SET LOCAL-REMOTE CONTROL 3-HS-252-02A is in the REMOTE position.
Step 3:
[18] PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE Critical Step SYNC SWITCH SS-7, 3-HS-252-03/SS-7 in ON.
SAT Standard:
UNSAT SIMULATED PLACING UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 3-HS-252-03/SS-7, in the ON N/A position.
5
STEP / STANDARD SAT / UNSAT Cue: The Unit 3 PFD SYSTEM GENERATOR SOURCE SYNC SS-7, SWITCH 3-HS-252-003/SS-7 is in the ON position.
Step 4:
NOTE MMG voltage and hertz are read as INCOMING.
Critical Step
[19] MATCH Incoming to Running AC volts using UNIT 3 MMG VOLTAGE ADJUST, 3-HS-252-02CD. SAT Standard: UNSAT SIMULATED MANIPULATING UNIT 3 MMG VOLTAGE ADJUST, N/A 3-HS 252-02CD until cued that incoming and running AC volts are matched.
Cue: INCOMING and RUNNING VOLTAGES are EQUAL at 122 Volts Step 5:
[20] ADJUST MMG speed using UNIT 3 MMG FREQUENCY ADJUST, 3-HS-252-02CF to obtain a synchroscope slowly rotating in the SLOW Critical Step (counter-clockwise) direction (10 to 15 second rotation) as indicated on SYNCHROSCOPE, 0-SCP-252-000A/B.
SAT Standard:
UNSAT SIMULATED ADJUSTING UNIT 3 MMG FREQUENCY ADJUST N/A 3-HS-252-02CF speed control switch until cued that synchroscope indicator rotating in the counterclockwise direction at 10 to 15 seconds per revolution.
Cue: State: The Initial Synchroscope indicator is standing still at the 5 oclock position.
Note: If student raises frequency the state: Synchroscope indicator is rotating in the CLOCKWISE direction at 12 seconds per revolution.
Note: If student lowers frequency the state: Synchroscope indicator is rotating in the COUNTERCLOCKWISE direction at 12 seconds per revolution.
6
STEP / STANDARD SAT / UNSAT Step 6:
NOTES
- 1) Section 5.5[21] should be performed expeditiously (within about 15 seconds) to minimize the time AC Systems are paralleled to prevent tripping the MMG set. Voltage and amps is expected to fluctuate while the AC systems are paralleled and the MMG set will trip if the AC systems are paralleled for approximately 30 seconds.
- 2) If breaker 1001 trips, it must be reset with reset push button on the respective Unit Battery Board, Panel 10.
CAUTIONS
- 1) Voltage Oscillations may occur during Bus Power Transfers.
These oscillations are caused when two Power Supplies having separate Voltage Regulators try to maintain voltage control.
Therefore, the time the Power Supplies are paralleled should be minimized as follows:[PER 64835]
- When transferring Bus power supplies from one MMG to Critical Step another MMG.
- When transferring Bus power supplies from one MMG with the SAT unit preferred transformer. (Unit 2 has a Voltage Regulator Transformer which makes voltage oscillations more UNSAT susceptible.)
N/A
- 2) Minimize the number of Bus power supply transfers and only transfer Bus power supplies when absolutely necessary.
- 3) During the transfer of Bus power supplies the affiliated RPS circuit protectors 1(2)C1 and/or 1(2)C2 may trip.
Start of Critical Step(s)
[21] WHEN SYNCHROSCOPE, 0-SCP-252-000A/B is 5 minutes prior to 12 o'clock, in the SLOW counter-clockwise direction, THEN PERFORM the following expeditiously:
[21.1] CLOSE UNIT 3 BKR 1001, using 0-HS-280-003/1001.
[21.2] ENSURE CLOSED UNIT 3 BKR 1001.
7
STEP / STANDARD SAT / UNSAT Standard( step 6 continued):
When cued synchroscope indicator at 5 minutes prior to 12 o'clock, SIMULATED PLACING 3-BKR 1001, 0-HS-252-003/1001 in the CLOSE position.
NOTE: IT WOULD ASSIST THE EXAMINEE IF THE EVALUATOR WOULD USE HIS FINGER TO DEMONSTRATE INDICATOR POSITION ON THE SYNCHROSCOPE AS THE READINGS ARE ENUNCIATED.
CUE: THE SYNCHROSCOPE INDICATOR IS AT 30 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 15 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 5 MINUTES BEFORE THE 12 O'CLOCK POSITION.
CUE: [WHEN CLOSED] UNIT 3 BREAKER 1001 BREAKER POSITION INDICATING LAMP CHANGED FROM ILLUMINATED GREEN TO ILLUMINATED RED.
Step 7:
[21.3] OPEN the UNIT 3)BKR 1002, using 0-HS-280-003/1002. Critical Step End of Critical Step(s) SAT Standard: UNSAT SIMULATED UNIT 3 BKR 1002, 0-HS-282-003/1002in the OPEN N/A position.
CUE: UNIT 3 BKR 1002, 0-HS-282-003/1002 IS IN THE OPEN POSITION WITH RED LIGHT ILLUMINATED.
NOTE: DO NOT ALLOW THE EXAMINEE TO OPERATE THE AMMETER SELECTOR SWITCH FOR THE FOLLOWING STEP.
Step 8:
[22] CHECK generator is loaded by observing UNIT 3 MMG GENERATOR amps, 3-II-252-02C/1AMR L2 rise, "N" should be UNSAT approximately the difference of L1& L2 (UNIT 3 MMG GENERATOR amps, 3-HS-252-02CH positions 1, 2, & 3 are respective to L1, L2 & N).
N/A 8
STEP / STANDARD SAT / UNSAT Standard:
CHECKED amp indicators L1 MINUS L2 approximately equals n.
Cue: L1, L2, N AMPS INDICATIONS HAVE RISEN and L1-L2 = N.
Note: Selector Switch positions are labeled as follows: Position 1 is L1, position 2 is L2 and Position 3 is N.
Step 9:
[23] ENSURE OPEN UNIT 3 BKR 1003, 0-HS-280-003/1003 SAT Standard: UNSAT VERIFIED ILLUMINATED GREEN position indicating light above 0- N/A HS-282-003/1003.
Cue: Unit 3 Breaker 1003 0-HS-280-003/1003 Position Indicating Lamp changed from illuminated RED to illuminated GREEN.
Step 10:
[24] On Unit 2 Unit Preferred MMG Set Local Control Panel, ENSURE OPEN the following fused disconnect switches:
- BACKUP SOURCE TO BAT BD 1 BKR 1003, 1-FUDS-280-001/1003 SAT
- BACKUP SOURCE TO BAT BD 3 BKR 1003, 3-FUDS-280-UNSAT 003/1003 N/A Standard:
At Unit 2 Unit Preferred MMG Set Local Control Panel VERIFIED 1-FUDS-280-001/1003 AND 3-FUDS-280-003/1003 in the OPEN POSITION.
Cue: 1-FUDS-280-001/1003 and 3-FUDS-280-003/1003 are in the OPEN position.
9
STEP / STANDARD SAT / UNSAT Step 11:
[25] On Unit 3 Unit Preferred MMG Set Local Control Panel, ENSURE the BACKUP SOURCE TO BAT BD 2 BKR 1003, SAT 2-FUDS-280-002/1003 fused disconnect switch is open:
UNSAT Standard:
N/A On Unit 3 Unit Preferred MMG Set Local Control Panel, VERIFIED 2-FUDS-280-002/1003 in the OPEN position.
Cue: 2-FUDS-280-002/1003 is in the OPEN position.
Step 12:
[26] On Battery Board 2:
PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH SAT SS-7, 1-HS-252-03/SS-7 in OFF.
UNSAT Standard:
N/A SIMULATED PLACING UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 1-HS-252-03/SS-7 in the OFF position.
Cue: UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 1-HS-252-03/SS-7 is in the OFF position.
Step 13:
[27] On Battery Board 2:
Critical Step DEPRESS UNIT 3 MMG AC MOTOR START, 3-HS-252-02AD to return SAT to Normal AC power from DC drive.
UNSAT Standard:
N/A SIMULATED DEPRESSING and RELEASING UNIT 3 MMG AC MOTOR START , 3-HS-252-02AD pushbutton.
Cue: [The AC motor Breaker Position Indicating Lamp changed from illuminated GREEN to illuminated RED. State Another Operator will continue with procedure and this will end the task.
STOP TIME:
10
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is in cold shutdown
- The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1.
- Maintenance has been completed on the Unit 3 Unit Preferred MMG Set.
INITIATING CUES:
The SM directs you to start up and synchronize the Unit 3 Unit Preferred MMG Set as directed by 0-OI-57C per section 5.5 step 5.5[16].
NOTE: PERFORMER WILL NEED GGMKA KEY.
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
11
SITE: BFN JPM TITLE: RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: 80A U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: RO: 3.2 SRO: 3.3 201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL K/A No. &STATEMENT: CONTROL SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Rod Drift Alarm RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 1 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: __80A__
TASK STANDARD: Perform operations necessary to respond to a Control Rod Drift In per 2-AOI-85-5.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-85-5, 2-AOI-100-1 VALIDATIONTIME: 18 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/10 All Initial issue Incorrect task number; changed to U-085-AB-05:
1 09/01/15 1 Incorrect malfunction numbers; rd07r0231, rd07r2223 & rd07r3031; Corrected 3
SIMULATOR SETUP IC 28 Exam IC 280
- Run schedule file:NRC JPM A U2 -Control Rod Drift In
- Verify all triggers and overrides are correct
- Place the simulator in RUN to ensure stable conditions Console
- Start Rod Display on RWM Screen Operator Instructions
- Provide Initial Rod Data Sheet -PRLOG
- When prompted by the examiner, INSERT - Event 1 to Drift Control Rod 02-31 into the core
- When prompted by the examiner, INSERT - Event 2 to Drift Control Rod Multiple Control Rods into the core Malfunctions Description Event Severity Delay Initial set rd07r0231 Drifts rod 02-31 into 1 NA 35 sec NA core rd07r2223 Drifts rod 22-23 into 2 NA 10 sec NA core rd07r3031 Drifts rod 30-31 into 2 NA 25 sec NA core rd07r4635 Drifts rod 46-35 into 2 NA 20 sec NA core rd07r2619 Drifts rod 26-19 into 2 NA 30 sec NA core rd07r3027 Drifts rod 30-27 into 2 NA 18 sec NA core rd07r5423 Drifts rod 54-23 into 2 NA 23 sec NA core rd07r2255 Drifts rod 22-55 into 2 NA 28 sec NA core 4
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): NRC JPM A U2 -Control Rod Drift In 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is at 100% power INITIATING CUES:
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods.
6
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
NOTE
- 1) Problem details of any control rod issues observed during the performance of this surveillance must be recorded on Attachment 3 for further review and possible corrective maintenance. Slow/fast rod movements or settle times should be noted in the remarks section.
- 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1.
CAUTIONS
- 1) Any mispositioned control rod events will be dispositioned by following the direction contained within 2-AOI-85-7.
- 2) If a control rod moves unexpectedly one notch beyond its intended Critical Step position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. SAT
N/A 7.3 Exercising a Partially Withdrawn Control Rod
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40.
[2] OBSERVE the following for selected control rod:
- CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED.
- CHECK white light on the Full Core Display is ILLUMINATED.
- CHECK Rod Out Permit light is ILLUMINATED.
Standard:
Selects a withdrawn control rod Note to Examiner: May select any partially withdrawn control rod in any order 7
STEP / STANDARD SAT / UNSAT Step 2:
[3] INSERT control rod one notch by performing the following:
Critical Step
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN andRELEASE. SAT
[3.2] OBSERVE control rod settles into the desired position UNSAT andROD SETTLE light extinguishes.
N/A Standard:
Inserts withdrawn control rod one notch Step 3:
[4] WITHDRAW selected control rod one notch by performing the following: Critical Step
[4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD OUT NOTCHand RELEASE. SAT
[4.2] OBSERVE control rod settles into the desired position and UNSAT ROD SETTLE light extinguishes.
N/A Standard:
Withdraws withdrawn control rod one notch Step 4:
[5] DOCUMENT completion of control rod test as follows:
[5.1] PERFORMER
- INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the SAT control rodjust exercised to document proper movement and CRD latching. UNSAT
[5.2] Concurrent Verifier (CV) N/A
- ENSURE rod inserted and returned to its original position.
- INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised.
8
STEP / STANDARD SAT / UNSAT Standard:
Initials Attachment 1 for exercised control rod and continues to exercise rods.
Note to Examiner:
- Perform above actions for @ least two control rods.
- When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #1 for Control Rod 02-31 Drift In Note to Simulator Booth Operator:
- When directed by examiner insert trigger #1 for 02-31 Control Rod Drift In.
Step 5:
Performer recognizes control rod 02-31 drift in and responds per 2-AOI-85-5.
[2] IF a Control Rod is moving from its intended position without Critical Step operator actions, THEN INSERT the Control Rod to position 00 using CONTINUOUS IN. (Otherwise N/A) SAT
[3] IF a Control Rod Block occurs during rod insertion due to Rod UNSAT Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above.
(Otherwise N/A) N/A Standard:
Responds per 2-AOI-85-5 and inserts control rod 02-31 to full in position as indicated by position 00 indication.
CUE: When report to US, state Respond per 2-AOI-85-5, Control Rod Drift In.
Step 6:
[4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod SAT pattern.
UNSAT Standard:
Candidate notifies Reactor Engineer to Evaluate Core N/A Thermal limits and Preconditioning Limits for the current Control Rod Pattern Cue: Understand Reactor Engineering notified to evaluate Core Thermal andPreconditioning Limits 9
STEP / STANDARD SAT / UNSAT Step 7:
[5] IF another Control Rod Drift occurs before Reactor Engineering completes the evaluation,
[6] CHECK Thermal Limits on ICS (RUNMON). UNSAT Note to NRC Examiner: Step [6] performed by Reactor N/A Engineering.
Standard:
Reviews step and asks for guidance from US or RE CUE: As Shift Manager, state RE has evaluated Core Thermal and Preconditioning Limits and has determined that the Control Rod Exercise may continue and that any other Control Rod Drift will be considered the first.
Student will continue with Control Rod Exercise.
Step 8:
7.3 Exercising a Partially Withdrawn Control Rod
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. Critical Step
[2] OBSERVE the following for selected control rod: SAT
- CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. UNSAT
- CHECK white light on the Full Core Display is ILLUMINATED.
- CHECK Rod Out Permit light is ILLUMINATED. N/A Standard:
Selects a withdrawn control rod 10
STEP / STANDARD SAT / UNSAT Step 9:
[3] INSERT control rod one notch by performing the following:
Critical Step
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN SAT andRELEASE.
UNSAT
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes.
N/A Standard:
Inserts withdrawn control rod one notch Step 10:
[4] WITHDRAW selected control rod one notch by performing the Critical Step following:
[4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD SAT OUT NOTCHand RELEASE.
UNSAT
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes.
N/A Standard:
Withdraws withdrawn control rod one notch Note to Examiner:
When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #2 for Multiple Control Rods Drifting In Step 11:
Multiple Control Rods Drifting In Critical Step Standard:
Recognizes Multiple Control Rods Drift into the Core and Manually SAT Scrams the Reactor per 2-AOI-85-5.
UNSAT
- Depresses both SCRAM Pushbuttons
- Places mode switch in shutdown N/A
- Verifies All Rods in 11
STEP / STANDARD SAT / UNSAT Step 11 continued:
- Performs a Scram Announcement Critical Step o Rx Mode Switch Position: Shutdown o Rod Position: All Full In SAT o Reactor Water Level ____ & Trend ___
o Reactor Pressure ____ & Trend ___ UNSAT o MSIV Position: OPEN o Rx Power: <5% N/A Termination Criteria: REPEAT BACK SCRAM REPORT THEN STATE, THIS COMPLETES THE JPM. THAT WILL BE ALL FOR NOW, ANOTHER OPERATOR WILL CONTINUE IN 2-AOI-100-1.
STOP TIME:
12
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is at 100% power INITIATING CUES:
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods.
13
SITE: BFN JPM TITLE: RESPOND TO A CONTROL ROD DRIFT IN JPM NUMBER: 80A U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): U-085-AB-05/ Respond to a Control Rod Drift In K/A RATINGS: RO: 3.2 SRO: 3.3 201002 Reactor Manual Control System A2.02; Ability to (a) predict the impacts of the following on the REACTOR MANUAL CONTROL SYSTEM ; and (b) based on K/A No. &STATEMENT:
those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations:
Rod Drift Alarm RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 1 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _80A U3_
TASK STANDARD: Perform operations necessary to respond to a Control Rod Drift In per 3-AOI-85-5.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: 3-AOI-85-5, 3-AOI-100-1 VALIDATIONTIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/10 All Initial issue Incorrect task number; changed to U-085-AB-05:
1 05/11/15 1 Incorrect malfunction numbers; rd07r0231, rd07r2223 & rd07r3031; Corrected 3
SIMULATOR SETUP IC 28 Exam IC 280
- Run schedule file: NRC JPM A U3 -Control Rod Drift In
- Verify all triggers and overrides are correct
- Place the simulator in RUN to ensure stable conditions Console Operator
- Start Rod Display on RWM Screen Instructions
- Provide Initial Rod Data Sheet -PRLOG
- When prompted by the examiner, INSERT - Event 1 to Drift Control Rod 02-31 into the core
- When prompted by the examiner, INSERT - Event 2 to Drift Control Rod Multiple Control Rods into the core Malfunctions Description Event Severity Delay Initial set rd07r0231 Drifts rod 02-31 into 1 NA 35 sec NA core rd07r2223 Drifts rod 22-23 into 2 NA 10 sec NA core rd07r3031 Drifts rod 30-31 into 2 NA 25 sec NA core rd07r4635 Drifts rod 46-35 into 2 NA 20 sec NA core rd07r2619 Drifts rod 26-19 into 2 NA 30 sec NA core rd07r3027 Drifts rod 30-27 into 2 NA 18 sec NA core rd07r5423 Drifts rod 54-23 into 2 NA 23 sec NA core rd07r2255 Drifts rod 22-55 into 2 NA 28 sec NA core 4
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): NRC JPM A U3 -Control Rod Drift In 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is at 100% power INITIATING CUES:
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods.
6
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
NOTE
- 1) Problem details of any control rod issues observed during the performance of this surveillance must be recorded on Attachment 3 for further review and possible corrective maintenance. Slow/fast rod movements or settle times should be noted in the remarks section.
- 2) Section 7.3 is performed for all Partially Withdrawn Control Rods and performance of steps is represented by initialing the appropriate CRD exercised on Attachment 1.
CAUTIONS
- 3) Any mispositioned control rod events will be dispositioned by following the direction contained within 3-AOI-85-7.
- 4) If a control rod moves unexpectedly one notch beyond its intended Critical Step position, notify Unit Supervisor, obtain Unit Supervisor concurrence and return the rod to its intended position. SAT
N/A 7.3 Exercising a Partially Withdrawn Control Rod
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 3-XS-85-40.
[2] OBSERVE the following for selected control rod:
- CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED.
- CHECK white light on the Full Core Display is ILLUMINATED.
- CHECK Rod Out Permit light is ILLUMINATED.
Standard:
Selects a withdrawn control rod Note to Examiner: May select any partially withdrawn control rod in any order 7
STEP / STANDARD SAT / UNSAT Step 2:
[3] INSERT control rod one notch by performing the following:
Critical Step
[3.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD IN andRELEASE. SAT
[3.2] OBSERVE control rod settles into the desired position UNSAT andROD SETTLE light extinguishes.
N/A Standard:
Inserts withdrawn control rod one notch Step 3:
[4] WITHDRAW selected control rod one notch by performing the following: Critical Step
[4.1] PLACE CRD CONTROL SWITCH, 3-HS-85-48 in ROD OUT NOTCHand RELEASE. SAT
[4.2] OBSERVE control rod settles into the desired position and UNSAT ROD SETTLE light extinguishes.
N/A Standard:
Withdraws withdrawn control rod one notch Step 4:
[5] DOCUMENT completion of control rod test as follows:
[5.1] PERFORMER
- INITIAL Attachment 1 (Control Rod Exercise Data Sheet) in thebox corresponding to the control rod coordinates for the SAT control rodjust exercised to document proper movement and CRD latching. UNSAT
[5.2] Concurrent Verifier (CV) N/A
- ENSURE rod inserted and returned to its original position.
- INITIAL Attachment 2 (Control Rod Concurrent Verifier (CV)Check) in the box corresponding to the control rod coordinates forthe rod just exercised.
8
STEP / STANDARD SAT / UNSAT Standard:
Initials Attachment 1 for exercised control rod and continues to exercise rods.
Note to Examiner:
- Perform above actions for @ least two control rods.
- When satisfied with the number of rod manipulations direct Simulator Booth Operator to insert trigger #1 for Control Rod 02-31 Drift In Note to Simulator Booth Operator:
- When directed by examiner insert trigger #1 for 02-31 Control Rod Drift In.
Step 5:
Performer recognizes control rod 02-31 drift in and responds per 3-AOI-85-5.
[2] IF a Control Rod is moving from its intended position without Critical Step operator actions, THEN INSERT the Control Rod to position 00 using CONTINUOUS IN. (Otherwise N/A) SAT
[3] IF a Control Rod Block occurs during rod insertion due to Rod UNSAT Worth Minimizer, THEN BYPASS the RWM per step 4.2[1] above.
(Otherwise N/A) N/A Standard:
Responds per 3-AOI-85-5 and inserts control rod 02-31 to full in position as indicated by position 00 indication.
CUE: When report to US, state Respond per 3-AOI-85-5, Control Rod Drift In.
Step 6:
[4] NOTIFY the Reactor Engineer to Evaluate Core Thermal Limits and Preconditioning Limits for the current Control Rod SAT pattern.
UNSAT Standard:
Candidate notifies Reactor Engineer to Evaluate Core N/A Thermal limits and Preconditioning Limits for the current Control Rod Pattern Cue: Understand Reactor Engineering notified to evaluate Core Thermal andPreconditioning Limits 9
STEP / STANDARD SAT / UNSAT Step 7:
[5] IF another Control Rod Drift occurs before Reactor Engineering completes the evaluation,
[6] CHECK Thermal Limits on ICS (RUNMON). UNSAT Note to NRC Examiner: Step [6] performed by Reactor N/A Engineering.
Standard:
Reviews step and asks for guidance from US or RE CUE: As Shift Manager, state RE has evaluated Core Thermal and Preconditioning Limits and has determined that the Control Rod Exercise may continue and that any other Control Rod Drift will be considered the first.
Student will continue with Control Rod Exercise.
Step 8:
7.3 Exercising a Partially Withdrawn Control Rod
[1] SELECT desired control rod by DEPRESSING appropriate CRD ROD SELECT pushbutton 2-XS-85-40. Critical Step
[2] OBSERVE the following for selected control rod: SAT
- CHECK CRD ROD SELECT pushbutton is brightly ILLUMINATED. UNSAT
- CHECK white light on the Full Core Display is ILLUMINATED.
- CHECK Rod Out Permit light is ILLUMINATED. N/A Standard:
Selects a withdrawn control rod 10
STEP / STANDARD SAT / UNSAT Step 9:
[3] INSERT control rod one notch by performing the following:
Critical Step
[3.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD IN SAT andRELEASE.
UNSAT
[3.2] OBSERVE control rod settles into the desired position andROD SETTLE light extinguishes.
N/A Standard:
Inserts withdrawn control rod one notch Step 10:
[4] WITHDRAW selected control rod one notch by performing the Critical Step following:
[4.1] PLACE CRD CONTROL SWITCH, 2-HS-85-48 in ROD SAT OUT NOTCHand RELEASE.
UNSAT
[4.2] OBSERVE control rod settles into the desired position and ROD SETTLE light extinguishes.
N/A Standard:
Withdraws withdrawn control rod one notch Note to Examiner:
When satisfied with the number of rod manipulations direct Simulator BoothOperator to insert trigger #2 for Multiple Control Rods Drifting In Step 11:
Multiple Control Rods Drifting In Standard: Critical Step Recognizes Multiple Control Rods Drift into the Core and Manually Scrams the Reactor per 3-AOI-85-5. SAT
- Depresses both SCRAM Pushbuttons UNSAT
- Places mode switch in shutdown
- Verifies All Rods in N/A 11
STEP / STANDARD SAT / UNSAT Step 11 continued:
Critical Step
- Performs a Scram Announcement o Rx Mode Switch Position: Shutdown SAT o Rod Position: All Full In o Reactor Water Level ____ & Trend ___ UNSAT o Reactor Pressure ____ & Trend ___
o MSIV Position: OPEN N/A o Rx Power: <5%
Termination Criteria: repeat back scram report then state, this completes the JPM. That will be all for now, another operator will continue in 2-AOI-100-1 STOP TIME:
12
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is at 100% power INITIATING CUES:
The Unit Supervisor directs you to perform Surveillance 3.1.3.3 step 7.3, Control Rod Exercise Test for Withdrawn Control Rods, for partially withdrawn control rods.
13
SITE: BFN JPM TITLE: EHC Auto Cooldown JPM NUMBER: 276 U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-NO-32 Perform Reactor Cooldown TASK NUMBER / TASK TITLE(S): U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: RO: 3.9 SRO: 3.9 239001Main and Reheat Steam System: A4.09 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 4 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _276 U2 RO SRO DATE: _______
TASK STANDARD: Perform operations necessary to initiate an Auto Cooldown with Turbine Bypass Valves.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-OI-47 VALIDATIONTIME: 4 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 06/19/12 All Initial issue 1 07/22/15 All General revision & re-format 3
SIMULATOR SETUP IC 40 Exam IC 281
Console Operator Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): None 4
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves.
INITIATING CUES:
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 2-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6].
5
START TIME:
STEP / STANDARD SAT / UNSAT Step 1: SAT
[6] VERIFY EHC is in Pressure Control using 2-HS-47-204. UNSAT N/A Standard:
Observes light on for EHC Pressure Control on 2-HS-47-204.
Step 2:
[7] On the EHC Work Station on Panel 9-7:
[7.1] SELECT Main Menu from the toolbar at bottom of the screen. Critical Step
[7.2] SELECT Log In on Display Screen and ENTER OPS SAT for name and OPS for Password.
UNSAT
[7.3] SELECT Auto Cooldown from list of function on the screen. N/A Standard:
Candidate logs into EHC workstation and selects Auto Cooldown from the list of functions on the screen.
Step 3:
[8] On the Auto Cooldown Display Screen CHECK the following are displayed.
- Turbine Tripped or All Valves Closed - indicates Reset.
- Rx Press Ctrl - indicates Reset. UNSAT Standard: N/A
- Candidate checks the Turbine Tripped or All Valves Closed
-indicates Reset.
- Candidate checks Rx Press Ctrl - indicates Reset.
6
STEP / STANDARD SAT / UNSAT Step 4:
[9] On the Auto Cooldown Screen SET the desired Final Pressure for cooldown as follows:
[9.1] SELECT the block above the FINAL PRESSURE Critical Step TARGET.
[9.2] ENTER the desired pressure using the Display Screen or Key Board.
UNSAT
[9.3] WHEN desired Pressure is entered SELECT OK N/A Standard:
Candidate sets the desired final target pressure of 20psig (given in initial conditions).
Step 5:
[10] WHEN Cooldown is ready to commence, THEN
[10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary)
Critical Step
[10.2] DEPRESS the START button on the Auto Cooldown Display Screen. SAT
[11] WHEN Caution Are You Sure You Want to Initiate Auto UNSAT Cooldown? appears N/A SELECT Yes Screen Button to start the cooldown.
Standard:
Candidate depresses START and acknowledges YES to commence auto cooldown.
7
STEP / STANDARD SAT / UNSAT Step 6:
[12] CHECK the following:
- EHC PRESSURE SETPOINT, 2-PI-47-162, is lowering.
- EHC AUTO COOLDOWN displays IN PROGRESS SAT Standard: UNSAT Candidate monitors EHC pressure and the auto cooldown is IN N/A PROGRESS.
Cue: The Unit Supervisor directs you to adjust the Final Pressure Target to 100 psig.
Step 7:
[13] IF it is desired to change the Final Pressure Target, THEN On the Auto Cooldown Screen.
[13.1] SELECT the block above the FINAL PRESSURE TARGET Critical Step
[13.2] ENTER the desired pressure using the Display SAT Screen or Key Board.
UNSAT
[13.3] WHEN desired Pressure is entered SELECT OK N/A Standard:
Candidate adjusts FINAL PRESSURE TARGET to 100 psig and recommences the auto cooldown.
Evaluator Cue: Another operator will continue to monitor the cooldown. This completes your task.
STOP TIME:
8
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves.
INITIATING CUES:
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 2-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6].
9
SITE: BFN JPM TITLE: EHC Auto Cooldown JPM NUMBER: 276 U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-NO-32 Perform Reactor Cooldown TASK NUMBER / TASK TITLE(S): U-000-NO-34 Perform a Reactor Cooldown from Hot Standby Conditions K/A RATINGS: RO: 3.9 SRO: 3.9 239001Main and Reheat Steam System: A4.09 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor pressure RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 4 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _276 U3_
TASK STANDARD: Perform operations necessary to initiate an Auto Cooldown with Turbine Bypass Valves.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 3-OI-47 VALIDATIONTIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 06/19/12 All Initial issue 1 07/22/15 All General revision & re-format 3
SIMULATOR SETUP IC 40 Exam IC 281
Console Operator Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): None 4
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves.
INITIATING CUES:
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 3-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6].
5
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
[6] VERIFY EHC is in Pressure Control using 3-HS-47-204. SAT UNSAT Standard:
N/A Observes light on for EHC Pressure Control on 3-HS-47-204.
Step 2:
[7] On the EHC Work Station on Panel 9-7:
[7.1] SELECT Main Menu from the toolbar at bottom of the screen. Critical Step
[7.2] SELECT Log In on Display Screen and ENTER OPS SAT for name and OPS for Password.
UNSAT
[7.3] SELECT Auto Cooldown from list of function on the screen. N/A Standard:
Candidate logs into EHC workstation and selects Auto Cooldown from the list of functions on the screen.
Step 3:
[8] On the Auto Cooldown Display Screen CHECK the following are displayed.
- Turbine Tripped or All Valves Closed - indicates Reset.
- Rx Press Ctrl - indicates Reset. UNSAT Standard: N/A
- Candidate checks the Turbine Tripped or All Valves Closed
-indicates Reset.
- Candidate checks Rx Press Ctrl - indicates Reset.
6
Step 4:
[9] On the Auto Cooldown Screen SET the desired Final Pressure for cooldown as follows:
[9.1] SELECT the block above the FINAL PRESSURE Critical Step TARGET.
[9.2] ENTER the desired pressure using the Display Screen or Key Board.
UNSAT
[9.3] WHEN desired Pressure is entered SELECT OK N/A Standard:
Candidate sets the desired final target pressure of 20psig (given in initial conditions).
Step 5:
[10] WHEN Cooldown is ready to commence, THEN
[10.1] VERIFY Reactor Pressure is stable and being controlled by EHC Pressure Control with at least one Bypass Valve opened. (Adjust setpoint as necessary)
Critical Step
[10.2] DEPRESS the START button on the Auto Cooldown Display Screen. SAT
[11] WHEN Caution Are You Sure You Want to Initiate Auto UNSAT Cooldown? appears N/A SELECT Yes Screen Button to start the cooldown.
Standard:
Candidate depresses START and acknowledges YES to commence auto cooldown.
7
Step 6:
[12] CHECK the following:
- EHC PRESSURE SETPOINT, 3-PI-47-162, is lowering.
- EHC AUTO COOLDOWN displays IN PROGRESS SAT Standard: UNSAT Candidate monitors EHC pressure and the auto cooldown is IN N/A PROGRESS.
Cue: The Unit Supervisor directs you to adjust the Final Pressure Target to 100 psig.
Step 7:
[13] IF it is desired to change the Final Pressure Target, THEN On the Auto Cooldown Screen.
[13.1] SELECT the block above the FINAL PRESSURE TARGET Critical Step
[13.2] ENTER the desired pressure using the Display SAT Screen or Key Board.
UNSAT
[13.3] WHEN desired Pressure is entered SELECT OK N/A Standard:
Candidate adjusts FINAL PRESSURE TARGET to 100 psig and recommences the auto cooldown.
Evaluator Cue: Another operator will continue to monitor the cooldown. This completes your task.
STOP TIME:
8
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Plant has been shutdown in preparation for a refueling outage. The Main Turbine is tripped. Reactor Water Level is stable and under control. Reactor Pressure is stable and being controlled by bypass valves.
INITIATING CUES:
The Unit Supervisor directs you to commence an Auto Cooldown to 20 psig in accordance with 3-OI-47, Turbine-Generator System, Section 8.1.2, starting at step [6].
9
LOSS OF REFERENCE APRM TO ROD BLOCK SITE: BFN JPM TITLE:
MONITOR JPM NUMBER: 672A U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-085-AL-03 RESPOND TO CONTROL ROD TASK NUMBER / TASK TITLE(S):
WITHDRAWL BLOCK K/A RATINGS: RO: 3.1 SRO: 3.3 215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures K/A No. &STATEMENT:
to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR-3,4,5 RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 7 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _672A U2_
TASK STANDARD: Perform operations necessary to bypass an APRM Channel and clear a Control Rod Block from Rod Block Monitoring System.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-OI-85, 2-OI-92B, 2-ARP-9-5A, 2-SR-3.1.3.5(A)
VALIDATIONTIME: 16 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 3
SIMULATOR SETUP IC 39 Exam IC 282
- Reset to IC-39 to ~ 30% Reactor Power
- Open Event File: NRC JPM C U2 -RBM APRM Fail Downscale.evt Malfunctions Description Event Severity Delay Initial set NM07L3233C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-33-C NM07L4025B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-25-B NM07L4033D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-33-D NM07L0817B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-17-B NM07L4017B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-17-B NM07L4041D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-41-D NM07L4049B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-49-B NM07L4057B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-57-B NM07L4817C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-17-C NM07L4825C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-25-C NM07L4833A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-33-A NM07L4841A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-41-A NM07L4849C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-49-C NM07L0825B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-25-B 4
NM07L0833D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-33-D NM07L0841D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-41-D NM07L0849B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-49-B NM07L2409B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-09-B NM07L2417D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-17-D NM07L2425D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-25-D NM07L2433B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-33-B NM07L2449D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-49-D NM07L2457D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-57-D NM07L1617C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-17-C NM07L1625C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-25-C NM07L1633A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-33-A NM07L1641A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-41-A NM07L1649C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-49-C NM07L1657C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-57-C NM07L1609A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-09-A NM07L3209C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-09-C NM07L3217A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-17-A NM07L3225A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-25-A NM07L3249A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-49-A NM07L3257A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-57-A NM07L4009D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-09-D NM07L4809A LPRM AMPLIFIER 15 0 N/A N/A 5
FAILURE 48-09-A NM07L5617D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-17-D NM07L5633B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-33-B NM07L5641B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-41-B NM07L3241C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-41-C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLO4631LGREENT(1) Control Rod 46-31 15 0 N/A N/A GREEN INDICATION Schedule File(s):
Event File: NRC JPM C U2 -RBM APRM Fail Downscale.evt; <TRIGGER id="15" description="APRM Ch 2 Fail Downscale">ZLO4631LGREENT(1) == 0</TRIGGER>
Schedule File: NRC JPM C U2 -RBM APRM Fail Downscale.sch 6
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is at 30% power
- Startup Sequence Control Rod Movement Data Sheet 2-SR-3.1.3.5(A) completed through group 57.
- No Control Rods are Fast Notching INITIATING CUES:
The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14-31.
7
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
Step 2:
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT
- THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A)
N/A Standard:
Determines that step in N/A Step 3:
[3] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED 8
STEP / STANDARD SAT / UNSAT Step 4:
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 5:
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 6:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
9
STEP / STANDARD SAT / UNSAT Step 7:
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT
- THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A)
N/A Standard:
Determines that step in N/A Step 8:
[3] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 9:
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing 10
STEP / STANDARD SAT / UNSAT Step 10:
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 11:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
Step 12:
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT
- THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A)
N/A Standard:
Determines that step in N/A 11
STEP / STANDARD SAT / UNSAT Step 13:
[3] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 14:
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 15:
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 12
STEP / STANDARD SAT / UNSAT Note to Examiner: This begins the Alternate Path section of JPM Simulator Booth Operator: Insert Event Trigger #1 to fail APRM 2 Downscale.
Step 16:
APRM Sensor/Trip Point:
DOWNSCALE/
APRM Downscale: <= 5%
OPRM INOP OPRM Inop: Less than 23 operable cells 4
Sensor Location:
Control Room Panel 2-9-14.
Probable Cause:
A. Unbypassed APRM channel at or below sensor set point.
B. SI or SR in progress.
C. Unit shutdown (Mode 3 or 4). Critical Step D. Failed sensor.
SAT Automatic Action: UNSAT A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only)
N/A Operator Action:
A. DETERMINE which APRM/OPRM channel is downscale/inop.
B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 2-OI-92B.
13
STEP / STANDARD SAT / UNSAT Step 16(continued)
CONTROL ROD Sensor/Trip Point:
WITHDRAWAL Relays: 3A-K1 Nuclear Instrumentation BLOCK 3A-K2 Refuel Equipment in Use High Level in Scram Discharge 7 Volume Scram Discharge Volume High Water Level Bypass Rx Mode Switch in SHUTDOWN PRNM (ANY APRM OPRM or RBM)
Sensor Location:
Panel 2-9-28 Elevation 593' Aux Instr Room Probable Cause:
A. One or more sensors at or above set point.
B. Malfunction of sensor.
C. Control rod drop accident Automatic Action:
Rod withdrawal block Operator Action:
A. DETERMINE initiating condition from corresponding rod withdrawal block alarm(s) and REFER TO operator action for alarm(s).
Standard:
Reference 2-ARP-9-5A and identifies APRM Ch 2 is down scale and proceeds to bypass APRM Ch 2 per 2-OI-92B CUE: Respond as stated in Alarm Response Instruction and Bypass APRM Ch 2 per 3-OI-92B.
14
STEP / STANDARD SAT / UNSAT Step 17:
NOTES
- 1) Only one APRM/OPRM in each trip system can be bypassed at a time.
- 2) All operations are performed on Panel 2-9-5 unless specifically stated otherwise.
- 3) In order to prevent inadvertent rod withdrawal block or Reactor scram while operating APRM BYPASS selector switch, Verify that the BLUE BYPASSED lights on Panel 9-14 Voters are extinguished prior to selecting any other channel to be bypassed. After bypassing a channel, the applicable BLUE BYPASSED status lights on Panel 9-14 Voters are required to be illuminated prior to testing, operating, or working on that channel. SAT UNSAT 6.1 Bypassing APRM/OPRM Channel N/A CAUTION
[QA/C] SPP-10.4 requires approval of the Plant Manager or his designee prior to any planned operation with APRMs bypassed unless bypassing is specifically allowed within approved procedures.
[ISE-HPS-92-RO1]
[1] REVIEW all precautions and limitations. REFER TO Section 3.0.
Standard:
Demonstrates reviewing precautions and limitations section 3.0.
Step 18:
Critical Step
[2] PLACE APRM BYPASS, 2-HS-92-7B/S3, to desired channel to be bypassed. SAT Standard: UNSAT PLACE APRM BYPASS, 2-HS-92-7B/S3, to APRM CH 2 N/A 15
STEP / STANDARD SAT / UNSAT Step 19:
[3] CHECK BLUE BYPASSED lights illuminated on Panel 2-9-14 Voters. SAT Standard: UNSAT Observes BLUE BYPASS light illuminated on Panel 2-9-14 for N/A APRM CH 2.
Step 20:
[4] VERIFY white bypass light on Panel 2-9-5 is illuminated. SAT Standard: UNSAT Observes WHITE BYPASS light illuminated on Panel 2-9-5. N/A Note to Examiner: If needed, cue student to proceed with actions required to continue rod movements. Student may continue at step 21 or 24.
Step 21:
6.6.2 Actions Required During and Following Control Rod Withdrawal (continued)
[6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN SAT PERFORM the following at the Unit Supervisors discretion to UNSAT REINITIALIZE the RBM:
N/A
[6.1] PLACE CRD POWER, 2-HS-85-46 in the OFF position to deselect the Control Rod.
Standard:
CRD POWER, 2-HS-85-46 in the OFF position.
16
STEP / STANDARD SAT / UNSAT Step 22:
[6.2] PLACE CRD POWER, 2-HS-85-46, in the ON position.
UNSAT Standard:
N/A PLACED CRD POWER, 2-HS-85-46, in the ON position.
Step 23:
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and SAT PERFORM applicable section for Control Rod withdrawal.
UNSAT Standard:
N/A Continues with Control Rod Movement CUE: Proceed with Control Rod Movement.
Step 24:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 2-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
17
STEP / STANDARD SAT / UNSAT Step 25:
[2] IF selected control rod has been identified as a fast notching control rod by engineering, THEN SAT
- THROTTLE OPEN 2-PCV-085-0023 CRD, CRD DRIVE WATER PRESS CONTROL VLV, to as low as 180 psid using 2-HS UNSAT 23A. (Otherwise N/A)
N/A Standard:
Determines that step in N/A Step 26:
[3] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 27:
[4] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing 18
STEP / STANDARD SAT / UNSAT Step 28:
[5] PLACE CRD CONTROL SWITCH, 2-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[6] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 2-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Termination Criteria: When Control Rod is at position 04, state End of Task STOP TIME:
19
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is at 30% power
- Startup Sequence Control Rod Movement Data Sheet 2-SR-3.1.3.5(A) completed through group 57.
INITIATING CUES:
The US has directed you to raise Reactor Power to 40% per 2-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 58; Control Rod 14-31.
20
LOSS OF REFERENCE APRM TO ROD BLOCK SITE: BFN JPM TITLE:
MONITOR JPM NUMBER: 672A U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-085-AL-03 RESPOND TO CONTROL ROD TASK NUMBER / TASK TITLE(S):
WITHDRAWL BLOCK K/A RATINGS: RO: 3.1 SRO: 3.3 215002 Rod Block Monitor System A2.03; Ability to (a) predict the impacts of the following on the ROD BLOCK MONITOR SYSTEM ; and (b) based on those predictions, use procedures K/A No. &STATEMENT:
to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of associated reference APRM channel: BWR-3,4,5 RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 7 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _672A U3_
TASK STANDARD: Perform operations necessary to bypass an APRM Channel and clear a Control Rod Block from Rod Block Monitoring System.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant evolutions precisely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 3-OI-85, 3-OI-92B, 3-ARP-9-5A, 3-SR-3.1.3.5(A)
VALIDATIONTIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 04/30/15 All Initial issue 3
SIMULATOR SETUP IC 39 Exam IC 282
- Reset IC-39to ~ 30% Reactor Power
- Open Event File: NRC JPM C U3 -RBM APRM Fail Downscale.evt Malfunctions Description Event Severity Delay Initial set NM07L3233C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-33-C NM07L4025B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-25-B NM07L4033D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-33-D NM07L0817B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-17-B NM07L4017B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-17-B NM07L4041D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-41-D NM07L4049B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-49-B NM07L4057B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-57-B NM07L4817C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-17-C NM07L4825C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-25-C NM07L4833A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-33-A NM07L4841A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-41-A NM07L4849C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 48-49-C NM07L0825B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-25-B 4
NM07L0833D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-33-D NM07L0841D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-41-D NM07L0849B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 08-49-B NM07L2409B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-09-B NM07L2417D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-17-D NM07L2425D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-25-D NM07L2433B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-33-B NM07L2449D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-49-D NM07L2457D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 24-57-D NM07L1617C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-17-C NM07L1625C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-25-C NM07L1633A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-33-A NM07L1641A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-41-A NM07L1649C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-49-C NM07L1657C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-57-C NM07L1609A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 16-09-A NM07L3209C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-09-C NM07L3217A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-17-A NM07L3225A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-25-A NM07L3249A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-49-A NM07L3257A LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-57-A NM07L4009D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 40-09-D NM07L4809A LPRM AMPLIFIER 15 0 N/A N/A 5
FAILURE 48-09-A NM07L5617D LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-17-D NM07L5633B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-33-B NM07L5641B LPRM AMPLIFIER 15 0 N/A N/A FAILURE 56-41-B NM07L3241C LPRM AMPLIFIER 15 0 N/A N/A FAILURE 32-41-C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLO4631LGREENT(1) Control Rod 46-31 15 0 N/A N/A GREEN INDICATION Schedule File(s):
Event File: NRC JPM C U3 -RBM APRM Fail Downscale.evt; <TRIGGER id="15" description="APRM Ch 2 Fail Downscale">ZLO4631LGREENT(1) == 0</TRIGGER>
Schedule File: NRC JPM C U3 -RBM APRM Fail Downscale.sch 6
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is at 30% power
- Startup Sequence Control Rod Movement Data Sheet 3-SR-3.1.3.5(A) completed through group 58.
INITIATING CUES:
The US has directed you to raise Reactor Power to 40% per 3-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 59; Control Rod 22-39.
7
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
Step 2:
[2] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 3:
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing 8
STEP / STANDARD SAT / UNSAT Step 4:
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 5:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
Step 6:
[2] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED 9
STEP / STANDARD SAT / UNSAT Step 7:
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 8:
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Step 9:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
10
STEP / STANDARD SAT / UNSAT Step 10:
[2] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 11:
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 12:
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 11
STEP / STANDARD SAT / UNSAT Note to Examiner: This begins the Alternate Path section of JPM Simulator Booth Operator: Insert Event Trigger #1 to fail APRM 2 Downscale.
Step 13:
APRM Sensor/Trip Point:
DOWNSCALE/
APRM Downscale: <= 5%
OPRM INOP OPRM Inop: Less than 23 operable cells 4
Sensor Location:
Control Room Panel 3-9-14.
Probable Cause:
A. Unbypassed APRM channel at or below sensor set point.
B. SI or SR in progress.
C. Unit shutdown (Mode 3 or 4). Critical Step D. Failed sensor.
SAT Automatic Action: UNSAT A. Rod withdrawal block with Rx Mode Sw. in RUN.(APRM only)
N/A Operator Action:
A. DETERMINE which APRM/OPRM channel is downscale/inop.
B. IF APRM failed downscale, THEN BYPASS channel. REFER TO 3-OI-92B.
12
STEP / STANDARD SAT / UNSAT Step 13(continued)
CONTROL ROD Sensor/Trip Point:
WITHDRAWAL Relays:3A-K1 Nuclear Instrumentation BLOCK 7 3A-K2 Refuel Equipment in Use High Level in Scram Discharge Volume Scram Discharge Volume High Water Level Bypass Rx Mode Switch in SHUTDOWN PRNM (ANY APRM OPRM or RBM)
Sensor Location:
Panel 3-9-28 Elevation 593' Aux Instr Room Probable Cause:
A. One or more sensors at or above set point.
B. Malfunction of sensor.
C. Control rod drop accident Automatic Action:
Rod withdrawal block Operator Action:
A. DETERMINE initiating condition from corresponding rod withdrawalblock alarm(s) and REFER TO operator action for alarm(s).
Standard:
Reference 3-ARP-9-5A and identifies APRM Ch 2 is down scale and proceeds to bypass APRM Ch 2 per 3-OI-92B CUE:Respond as stated in Alarm Response Instruction and Bypass APRM Ch 2 per 3-OI-92B.
13
STEP / STANDARD SAT / UNSAT Step 14:
NOTES
- 1) Only one APRM/OPRM in each trip system can be bypassed at a time.
- 2) All operations are performed on Panel 3-9-5 unless specifically stated otherwise.
- 3) In order to prevent inadvertent rod withdrawal block or Reactor scram while operating APRM BYPASS selector switch, Verify that the BLUE BYPASSED lights on Panel 9-14 Voters are extinguished prior to selecting any other channel to be bypassed. After bypassing a channel, the applicable BLUE BYPASSED status lights on Panel 9-14 Voters are required to be illuminated prior to testing, operating, or working on that channel. SAT UNSAT 6.1 Bypassing APRM/OPRM Channel N/A CAUTION
[QA/C] SPP-10.4 requires approval of the Plant Manager or his designee prior to any planned operation with APRMs bypassed unless bypassing is specifically allowed within approved procedures.
[ISE-HPS-92-RO1]
[1] REVIEW all precautions and limitations. REFER TO Section 3.0.
Standard:
Demonstrates reviewing precautions and limitations section 3.0.
CUE: If asked per note 2 above, Panel 9-14 Voter BLUE LIGHTS are extinguished.
Step 15:
Critical Step
[2] PLACE APRM BYPASS, 3-HS-92-7B/S3, to desired channel to be bypassed. SAT Standard: UNSAT PLACE APRM BYPASS, 3-HS-92-7B/S3, to APRM CH 2 N/A 14
STEP / STANDARD SAT / UNSAT Step 16:
[3] CHECK BLUE BYPASSED lights illuminated on Panel 3-9-14 Voters. SAT Standard: UNSAT Simulates observing BLUE BYPASS light illuminated on Panel 3- N/A 9-14 for APRM CH 2.
Cue: Blue Light is illuminated on Panel 3-9-14 for APRM CH 2.
Step 17:
[4] VERIFY white bypass light on Panel 3-9-5 is illuminated. SAT Standard: UNSAT Observes WHITE BYPASS light illuminated on Panel 3-9-5. N/A Note to NRC Examiner: If needed, cue student to proceed with actions required to continue rod movements.Student may continue at step 18 or 21.
Step 18:
6.6.2 Actions Required During and Following Control Rod Withdrawal (continued)
[6] IF Control Rod movement was stopped to keep from exceeding a RBM setpoint or was caused by a RBM Rod Block, THEN SAT PERFORM the following at the Unit Supervisors discretion to UNSAT REINITIALIZE the RBM:
N/A
[6.1] PLACE CRD POWER, 3-HS-85-46 in the OFF position to deselect the Control Rod.
Standard:
CRD POWER, 3-HS-85-46 in the OFF position.
15
STEP / STANDARD SAT / UNSAT Step 19:
[6.2] PLACE CRD POWER, 3-HS-85-46, in the ON position.
UNSAT Standard:
N/A PLACED CRD POWER, 3-HS-85-46, in the ON position.
Step 20:
[6.3] IF desired, THEN CONTINUE to withdrawal Control Rods and SAT PERFORM applicable section for Control Rod withdrawal.
UNSAT Standard:
N/A Continues with Control Rod Movement Cue:If asked,Proceed with Control Rod Movement.
Step 21:
Critical Step
[1] SELECT the desired control rod by depressing the appropriate CRD ROD SELECT pushbutton, 3-XS-85-40.
SAT Standard:
UNSAT Selects Control Rod by depressing CRD ROD SELECT N/A pushbutton.
16
STEP / STANDARD SAT / UNSAT Step 22:
[2] OBSERVE the following for the selected control rod:
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED SAT
- Rod Out Permit light ILLUMINATED UNSAT Standard:
N/A VERIFIES
- CRD ROD SELECT pushbutton is brightly ILLUMINATED
- White light on the Full Core Display ILLUMINATED
- Rod Out Permit light ILLUMINATED Step 23:
[3] VERIFY Rod Worth Minimizer is operable and LATCHED into the SAT correct ROD GROUP when the Rod Worth Minimizer is enforcing UNSAT Standard:
N/A STEP is N/A due to Rod Block Monitor is Enforcing Step 24:
[4] PLACE CRD CONTROL SWITCH, 3-HS-85-48, in ROD OUT NOTCH, and RELEASE.
Critical Step
[5] OBSERVE the control rod settles into the desired position and SAT the ROD SETTLE light extinguishes.
UNSAT Standard:
N/A PLACED CRD CONTROL SWITCH, 3-85-48 in ROD OUT NOTCH position and RELEASED control switch to move Control Rod to Position 04 as indicated on Full Core Display.
Note to Examiner: Step is repeated to get Control Rod to Position 04 Termination Criteria: When Control Rod is at position 04, state End of Task STOP TIME:
17
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is at 30% power
- Startup Sequence Control Rod Movement Data Sheet 3-SR-3.1.3.5(A) completed through group 58.
INITIATING CUES:
The US has directed you to raise Reactor Power to 40% per 3-SR-3.1.3.5(A) in preparation for placing Feedwater Heaters and Moisture Separator Drain System in service. Start on Group 59; Control Rod 22-39.
18
Job Performance Measure (JPM) 2-EOI APPENDIX-6E INJECTION SUBSYSTEM LINEUP SITE: BFN JPM TITLE:
CS SYSTEM II JPM NUMBER: 257A U2 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-35/ Lineup Injection Subsystem-Core TASK NUMBER / TASK TITLE(S): Spray Loop I(II) in Accordance with EOI Appendix 6D(E)
K/A RATINGS: RO: 3.9 SRO: 3.9 209001 Low Pressure Core Spray SystemA4.08 Ability to K/A No. &STATEMENT: manually operate and/or monitor in thecontrol room: Reactor water level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 2 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _257A U2_
TASK STANDARD: Perform operations necessary to identify and corrects Inboard and Outboard Injection Valve lineup in order to inject water into the RPV with Core Spray System II to recover level Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-EOI APPENDIX-6E VALIDATIONTIME: 8 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 12/06/10 All Initial issue 1 04/27/15 All General revision & re-format 3
SIMULATOR SETUP IC 28 Exam IC 283
- 1. Open Schedule File
- 2. Open Event File
- 3. Reset to IC-28and take out of freeze.
- 4. CLOSE 2-FCV-75-51 Console
- 5. OPEN 2-FCV-75-53 Operator
Instructions
- 7. Open 6 ADS Valves.
- 8. Wait until various alarms with Supp Pool Temp High come in to save IC.
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 15 75% 5 Yes INSIDE DRYWELL CS04A CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV II CS02B CS INBOARD 15 N/A N/A Yes INJECTION VALVE AUTO OPENING FAILURE (FCV 53)
RH06A RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV I RH06B RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV II RC01 RCIC TURBINE TRIP 15 N/A N/A Yes SYSTEM FAILURE HP04 HPCI STEAM 15 N/A N/A Yes SUPPLY VALVE AUTO OPENING FAILURE FW01A CONDENSATE 15 N/A 10 Yes PUMP TRIP 2A 4
FW01B CONDENSATE 15 N/A 10 Yes PUMP TRIP 2B FW01C CONDENSATE 15 N/A 10 Yes PUMP TRIP 2C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): JPM 257A U2 Core Spray Alt Inj.sch Event File(s): JPM 257A U2 Core Spray Alt Inj.evt 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is Shutdown
- RPV Water Level is lowering slowly.
- 1-EOI-1 has been entered and followed to RC-L6.
INITIATING CUES:
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above
(-)162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II.
6
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
Location: Unit 2 Control Room Attachments: 1. NPSH Monitoring
[1] VERIFY OPEN the following valves:
- 2-FCV-75-30, CORE SPRAY PUMP 2B SUPPR POOL SUCT UNSAT VLV
- 2-FCV-75-39, CORE SPRAY PUMP 2D SUPPR POOL SUCT N/A VLV Standard:
Verifies2-FCV-75-30 and 2-FCV-75-39 are open.
Step 2:
[1] (continued)VERIFY OPEN the following valves: Critical Step
- 2-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE. SAT UNSAT Standard:
N/A Recognizes 2-FCV-75-51 is closed and 2-FCV-75-53 is open, valve closes 2-FCV-75-53 and Opens 2-FCV-75-51.
Note to Examiner: Student will realignper OPDP-8 Conduct of Ops or OI-75, Core Spray System line up.
7
STEP / STANDARD SAT / UNSAT Step 3:
[2] VERIFY CLOSED 2-FCV-75-50, CORE SPRAY SYS II SAT TESTVALVE.
UNSAT Standard:
N/A Verifies 2-FCV-75-50 closed Step 4:
Critical Step
[3] VERIFY CS Pump 2B and/or 2D running.
SAT Standard:
UNSAT Starts Core Pumps 2B and/or 2D N/A (Only starting one pump is Critical, the second pump is optional).
Step 6:
[4] WHEN RPV pressure is below 450 psig, THEN Critical Step THROTTLE2-FCV-75-53, CORE SPRAY SYS II INBDINJECT VALVE, SAT as necessary to control injection at or below4000 gpm per pump.
UNSAT Standard:
N/A Verifies pressure < 450 psig and opens 2-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or
<8000 gpm for 2 pumps).
Step 7:
CAUTION Continuous operation with inadequate NPSH may result in pump damage or pump inoperability.
[5] MONITOR Core Spray Pump NPSH using Attachment 1.
UNSAT Standard:
Operator comparesCore Spray Pump flow rate with Suppression N/A Pool temperature and Suppression Pool pressure and Determined adequate NPSH.
Termination Criteria: Once rector Water Level is > TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure.
STOP TIME:
8
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is Shutdown
- RPV Water Level is lowering slowly.
- 1-EOI-1 has been entered and followed to RC-L6.
INITIATING CUES:
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above 162 inches (TAF) using Core Spray System II as directed by 2-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II.
9
Job Performance Measure (JPM) 3-EOI APPENDIX-6E INJECTION SUBSYSTEM LINEUP SITE: BFN JPM TITLE:
CS SYSTEM II JPM NUMBER: 257A U3 REVISION: 1 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-35/ Lineup Injection Subsystem-Core TASK NUMBER / TASK TITLE(S): Spray Loop I(II) in Accordance with EOI Appendix 6D(E)
K/A RATINGS: RO: 3.9 SRO: 3.9 209001 Low Pressure Core Spray System A4.08 Ability to K/A No. &STATEMENT: manually operate and/or monitor in the control room: Reactor water level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 2 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _257A U3_
TASK STANDARD: Perform operations necessary to identify and corrects Inboard and Outboard Injection Valve lineup in order to inject water into the RPV with Core Spray System II to recover level Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 3-EOI APPENDIX-6E VALIDATIONTIME: 5 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 12/06/10 All Initial issue 1 04/27/15 All General revision & re-format 3
SIMULATOR SETUP IC 28 Exam IC 283
- 1. Open Schedule File
- 2. Open Event File
- 3. Reset to IC-28 and take out of freeze.
- 4. CLOSE 2-FCV-75-51 Console
- 5. OPEN 2-FCV-75-53 Operator
Instructions
- 7. Open 6 ADS Valves.
- 8. Wait until various alarms with Supp Pool Temp High come in to save IC.
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 15 75% 5 Yes INSIDE DRYWELL CS04A CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 15 N/A N/A Yes LOGIC POWER FAILURE DIV II CS02B CS INBOARD 15 N/A N/A Yes INJECTION VALVE AUTO OPENING FAILURE (FCV 53)
RH06A RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV I RH06B RHR LOGIC POWER 15 N/A N/A Yes FAILURE DIV II RC01 RCIC TURBINE TRIP 15 N/A N/A Yes SYSTEM FAILURE HP04 HPCI STEAM 15 N/A N/A Yes SUPPLY VALVE AUTO OPENING FAILURE FW01A CONDENSATE 15 N/A 10 Yes PUMP TRIP 3A 4
FW01B CONDENSATE 15 N/A 10 Yes PUMP TRIP 3B FW01C CONDENSATE 15 N/A 10 Yes PUMP TRIP 3C Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Schedule File(s): JPM 257A U3 Core Spray Alt Inj.sch Event File(s): JPM 257A U3 Core Spray Alt Inj.evt 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is Shutdown
- RPV Water Level is lowering slowly.
- 1-EOI-1 has been entered and followed to RC-L6.
INITIATING CUES:
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level above
(-)162 inches (TAF) using Core Spray System II as directed by 3-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II.
6
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
Location: Unit 3 Control Room Attachments: 1. NPSH Monitoring
[1] VERIFY OPEN the following valves:
- 3-FCV-75-30, CORE SPRAY PUMP 3B SUPPR POOL SUCT UNSAT VLV
- 3-FCV-75-39, CORE SPRAY PUMP 3D SUPPR POOL SUCT N/A VLV Standard:
Verifies3-FCV-75-30 and 3-FCV-75-39 are open.
Step 2:
Critical Step
[1] (continued) VERIFY OPEN the following valves:
- 3-FCV-75-51, CORE SPRAY SYS II OUTBD INJECT VALVE.
SAT UNSAT Standard:
N/A Recognizes 3-FCV-75-51 is closed and 3-FCV-75-53 is open, closes 3-FCV-75-53 and Opens 3-FCV-75-51.
Note to Examiner: Student will realignper OPDP-8 Conduct of Ops or OI-75, Core Spray System line up.
7
STEP / STANDARD SAT / UNSAT Step 3:
[2] VERIFY CLOSED 3-FCV-75-50, CORE SPRAY SYS II TEST SAT VALVE.
UNSAT Standard:
N/A Verifies 3-FCV-75-50 closed Step 4:
Critical Step
[3] VERIFY CS Pump 3B and/or 3D running.
SAT Standard:
UNSAT Starts Core Pumps 3B and/or 3D (Only starting one pump is N/A Critical, the second pump is optional).
Step 6:
[4] WHEN RPV pressure is below 450 psig, THEN Critical Step THROTTLE 3-FCV-75-53, CORE SPRAY SYS II INBDINJECT VALVE, SAT as necessary to control injection at or below4000 gpm per pump.
UNSAT Standard:
N/A Verifies pressure < 450 psig and opens 3-FCV-75-53 and commences injection. (And verify flow <4000 gpm for 1 pump or
<8000 gpm for 2 pumps).
Step 7:
CAUTION Continuous operation with inadequate NPSH may result in pump damage or pump inoperability.
[5] MONITOR Core Spray Pump NPSH using Attachment 1.
UNSAT Standard:
Operator compares Core Spray pump flow rate with Suppression N/A Pool temperature and Suppression Pool pressure and Determined adequate NPSH.
Termination Criteria: Once rector Water Level is > TAF JPM may be terminated. IF student fails to recover reactor water level above TAF (-162 inches), it will be considered a failure.
STOP TIME:
8
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is Shutdown
- RPV Water Level is lowering slowly.
- 1-EOI-1 has been entered and followed to RC-L6.
INITIATING CUES:
The Unit Supervisor directs you to inject water into the RPV to restore RPV water level using Core Spray System II as directed by 3-EOI Appendix-6E, Injection Subsystems Lineup Core Spray System II. Directed level band is +2 to +51 inches.
9
Job Performance Measure (JPM) 2-EOI Appendix-11F Alternate RPV Pressure Control SITE: BFN JPM TITLE:
Systems: RFPT On Minimum Flow JPM NUMBER: 670A U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-58 Lineup Alternate RPV Pressure Control TASK NUMBER / TASK TITLE(S): Systems- RFPT on Minimum Flow IAW EOI Appendix 11F K/A RATINGS: RO: 3.6SRO: 3.6 239001 Main and Reheat Steam System A1.01 Ability to predict and/or monitor changes in parameters associated with K/A No. &STATEMENT:
operating the MAIN ANDREHEAT STEAM SYSTEM controls including: Main steam pressure RELATED PRA INFORMATION: None SAFETY FUNCTION: 3 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _670A U2_
TASK STANDARD: Perform operations necessary to necessary to place one RFPT in pressure control as directed by 2-EOI Appendix-11F.
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 2-EOI-APPENDIX-11F VERIFICATION TIME: 12 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 284 Malfunctions Description Event Severity Delay Initial set fw15a SPURIOUS RFP 15 N/A 0 N/A BEARING LOW OIL PRESSURE tc03a-j Fail Bypass Valves 1 0% 0 N/A closed ad01e 20 SRV 1-31 stuck open 1 20% 0 N/A 20%
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Initial Setup:
- 1. Reset to IC 28
- 2. Manually Scram RX
- 3. Trip 2A and 2B RFPT
- 5. Insert Manual Trigger #1
- 7. Verify Auto Trigger #15 is ACTIVE
- 8. Freeze simulator and save IC.
Schedule Files:
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 4
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 2C.
INITIATING CUES:
The Unit Supervisor directs you to place 2A RFPT in alternate pressure control, as directed by 2-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig.
5
START TIME STEP / STANDARD SAT / UNSAT Step 1:
[1] IF BOTH of the following exist:
- Emergency RPV Depressurization is required, AND
- Group 1 Isolation Signal exists, THEN SAT EXIT this procedure and ENTER EOI Appendix 11H. UNSAT N/A Standard:
Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve.
Step 2:
[2] VERIFY MSIVs open.
UNSAT Standard:
N/A Verifies MSIVs OPEN 6
STEP / STANDARD SAT / UNSAT Step 3:
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. SAT Standard: UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 4:
[4] PLACE RFPTs in service as follows:
[4.1] VERIFY the following:
[4.1.1] At least one condensate pump running.
[4.1.2] At least one condensate booster pump running.
UNSAT
[4.1.3] Condensate System aligned to supply suction toRFPs.
N/A Standard:
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs.
Step 5:
[4.2] VERIFY Main Oil Pump running for each RFPT to bestarted. SAT Standard: UNSAT Verifies main oil pump running for RFPT 2A N/A Step 6:
Critical Step
[4.3] VERIFY CLOSED 2-FCV-3-19, RFP 2ADISCHARGE VALVE.
SAT Standard:
UNSAT VERIFY CLOSED 2-FCV-3-19, RFP 2A DISCHARGE VALVE.
N/A 7
STEP / STANDARD SAT / UNSAT Step 7:
Critical Step
[4.4] DEPRESS 2-HS-46-8A RFPT 2A SPEED CONT RAISE/LOWER, and VERIFY amber lightis illuminated. SAT Standard: UNSAT Depresses 2-HS-46-8A N/A Step 8:
[4.5] DEPRESS 2-HS-3-124A, RFPT 2A TRIP RESET. Critical Step Standard: SAT Depresses 2-HS-3-124A and verifies the 2-Z1-1-123 LP Stop Valve and UNSAT 2-Z1-127 HP Stop Valve comes OPEN.
N/A Step 9:
Critical Step
[4.6] PLACE 2-HS-46-112A RFPT 2A START/LOCAL ENABLE, in START. SAT Standard: UNSAT Places 2-HS-46-112A in START N/A Note to Examiner:
RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10:
Critical Step
[4.7] CHECK RFPT 2A speed increases to approximately 600 rpm.
SAT Standard:
UNSAT Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 2-EOI-APPENDIX-11F. N/A CUE:
US: Proceed as directed per 2-EOI-APPENDIX-11F.
AO: Reports an oil leak of ~5 gpm on RFPT A bearings.
8
STEP / STANDARD SAT / UNSAT Step 11:
[1] IF BOTH of the following exist:
- Emergency RPV Depressurization is required, AND
UNSAT Standard: N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve.
Step 12:
[2] VERIFY MSIVs open. SAT Standard: UNSAT Verifies MSIVs OPEN N/A 9
STEP / STANDARD SAT / UNSAT Step 13:
[3] VERIFY Hotwell Pressure at or below -7 in. Hg. SAT Standard: UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 14:
[4] PLACE RFPTs in service as follows:
[4.1] VERIFY the following:
[4.1.1] At least one condensate pump running.
[4.1.2] At least one condensate booster pump running.
UNSAT
[4.1.3] Condensate System aligned to supply suction toRFPs.
N/A Standard:
Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs.
Step 15:
[4.2] VERIFY Main Oil Pump running for each RFPT to be started. SAT Standard: UNSAT Verifies main oil pump running for RFPT 2B N/A Step 16:
Critical Step
[4.3] VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE.
SAT Standard:
UNSAT VERIFY CLOSED 2-FCV-3-12, RFP 2B DISCHARGE VALVE.
N/A 10
STEP / STANDARD SAT / UNSAT Step 17:
Critical Step
[4.4] DEPRESS 2-HS-46-9A, RFPT 2BSPEED CONT RAISE/LOWER, and VERIFY amber light is illuminated. SAT Standard: UNSAT Depresses 2-HS-46-9A N/A Step 18:
Critical Step
[4.5] DEPRESS 2-HS-3-150A, RFPT 2B TRIP RESET.
SAT Standard:
UNSAT Depresses 2-HS-3-150A and verifies the 2-ZI-1-133 LP Stop Valve and 2-FCV-135 HP Stop Valve comes OPEN. N/A Step 19:
Critical Step
[4.6] PLACE 2-HS-46-138A, RFPT 2B START/LOCAL ENABLE, in START. SAT Standard: UNSAT Places 2-HS-46-138A in START N/A Step 20:
[4.7] CHECK RFPT 2B speed increases to approximately 600 rpm. SAT Standard: UNSAT Verifies RFPT 2B speed increases to approximately 600 rpm N/A 11
STEP / STANDARD SAT / UNSAT Step 21:
[4.8] VERIFY OPEN 2-FCV-3-13, RFP2B MIN FLOW VALVE. SAT Standard: UNSAT Verifies 2-FCV-3-13 OPEN N/A Step 21:
CAUTION RFP discharge pressure is limited to below 1250 psig to avoid system damage.
[4.9] PLACE 2-HS-46-9A, RFPT 2B SPEED CONT RAISE/LOWER in Critical Step RAISE to raise RFPT speed, maintaining discharge pressure less than 1250 psig. SAT Standard: UNSAT Raises RFPT speed using Manual Speed Control Handswitch, N/A maintaining discharge pressure <1250 psig as indicated on 2-PI-3-9A RFPT 2B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable).
STOP TIME END OF TASK 12
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2. The Unit 2 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 2C.
INITIATING CUES:
The Unit Supervisor directs you to place 2A RFPT in alternate pressure control, as directed by 2-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig.
13
Job Performance Measure (JPM) 3-EOI Appendix-11F Alternate RPV Pressure Control SITE: BFN JPM TITLE:
Systems: RFPT On Minimum Flow JPM 670A JPM NUMBER: REVISION: 0 U3 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-58 Lineup Alternate RPV Pressure Control TASK NUMBER / TASK TITLE(S): Systems- RFPT on Minimum Flow IAW EOI Appendix 11F K/A RATINGS: RO: 3.6 SRO: 3.6 239001 Main and Reheat Steam System A1.01 Ability to predict and/or monitor changes in parameters associated with K/A No. & STATEMENT:
operating the MAIN AND REHEAT STEAM SYSTEM controls including: Main steam pressure RELATED PRA INFORMATION: None SAFETY FUNCTION: 3 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _______
TASK STANDARD: Perform operations necessary to necessary to place one RFPT in pressure control as directed by 3-EOI Appendix-11F.
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 3-EOI-APPENDIX-11F VERIFICATION TIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 284 Malfunctions Description Event Severity Delay Initial set fw15a SPURIOUS RFP 15 N/A 0 N/A BEARING LOW OIL PRESSURE tc03a-j Fail Bypass Valves 1 0% 0 N/A closed ad01e SRV 1-31 stuck open 1 26% 0 N/A Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set 3
Initial Setup:
- 1. Reset to IC 28
- 2. Manually Scram RX
- 3. Trip 2A and 2B RFPT
- 5. Insert Manual Trigger #1
- 7. Verify Auto Trigger #15 is ACTIVE
- 8. Freeze simulator and save IC.
Schedule Files:
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/11/15 All Initial issue 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3. The Unit 3 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 3C.
INITIATING CUES:
The Unit Supervisor directs you to place 3A RFPT in alternate pressure control, as directed by 3-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig.
6
START TIME STEP / STANDARD SAT / UNSAT Step 1:
[1] IF BOTH of the following exist:
- Emergency RPV Depressurization is required, AND
UNSAT Standard: N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve.
Step 2:
[2] VERIFY MSIVs open.
SAT Standard:
UNSAT Verifies MSIVs OPEN N/A 7
STEP / STANDARD SAT / UNSAT Step 3:
[3] VERIFY Hotwell Pressure at or below -7 in. Hg.
SAT Standard:
UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 4:
[4] PLACE RFPTs in service as follows:
[4.1] VERIFY the following:
[4.1.1] At least one condensate pump running.
[4.1.2] At least one condensate booster pump running.
[4.1.3] Condensate System aligned to supply suction to RFPs.
UNSAT Standard:
N/A Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs.
Step 5:
[4.2] VERIFY Main Oil Pump running for each RFPT to be started.
SAT Standard:
UNSAT Verifies main oil pump running for RFPT 3A N/A Step 6: Critical Step
[4.3] VERIFY CLOSED 3-FCV-3-19, RFP 3A DISCHARGE VALVE.
SAT Standard:
UNSAT VERIFY CLOSED 3-FCV-3-19, RFP 3A DISCHARGE VALVE.
N/A 8
STEP / STANDARD SAT / UNSAT Step 7:
[4.4] DEPRESS 3-HS-46-8A, RFPT 3A SPEED CONT RAISE/LOWER, Critical Step and VERIFY amber light is illuminated.
SAT Standard:
UNSAT Depresses 3-HS-46-8A N/A Step 8:
[4.5] DEPRESS 3-HS-3-124A, RFPT 3A TRIP RESET. Critical Step Standard: SAT Depresses 3-HS-3-124A and resets RFPT Trip and verifies the 3-ZI UNSAT 123 LP Stop Valve and 3-ZI-127 HP Stop Valve comes OPEN.
N/A Step 9:
[4.6] PLACE 3-HS-46-112A RFPT 3A START/LOCAL ENABLE, in Critical Step START.
SAT Standard:
UNSAT Places 3-HS-46-112A in START N/A Note to Examiner:
RFPT A will Trip due to Low Bearing Oil Pressure at > 350 RPM Step 10:
[4.7] CHECK RFPT 3A speed increases to approximately 600 rpm.
SAT Standard:
UNSAT Operator responds to RFPT A Trip and reports to US and begins to use B RFP for RPV Pressure Control per 3-EOI-APPENDIX-11F. N/A CUE:
US: Proceed as directed per 3-EOI-APPENDIX-11F.
AO: Reports an oil leak of ~5 gpm on RFPT A bearings.
9
STEP / STANDARD SAT / UNSAT Step 11:
[1] IF BOTH of the following exist:
- Emergency RPV Depressurization is required, AND
- Group 1 Isolation Signal exists, THEN EXIT this procedure and ENTER EOI Appendix 11H. SAT UNSAT Standard:
N/A Verifies that a Group 1 Isolation signal Does Not exist by observing illuminated RED PCIS Group I lights and/or Verified MSIVs are open by observing illuminated RED valve position indicating lights for each valve.
Step 12:
[2] VERIFY MSIVs open.
SAT Standard:
UNSAT Verifies MSIVs OPEN N/A 10
STEP / STANDARD SAT / UNSAT Step 13:
[3] VERIFY Hotwell Pressure at or below -7 in. Hg.
SAT Standard:
UNSAT Verifies Hotwell Pressure at or below -7 in. Hg N/A Step 14:
[4] PLACE RFPTs in service as follows:
[4.1] VERIFY the following:
[4.1.1] At least one condensate pump running.
[4.1.2] At least one condensate booster pump running.
[4.1.3] Condensate System aligned to supply suction to RFPs.
UNSAT Standard:
N/A Verifies one condensate pump and one condensate booster pump running, verifies condensate system aligned to supply suction to RFPs.
Step 15:
[4.2] VERIFY Main Oil Pump running for each RFPT to be started.
SAT Standard:
UNSAT Verifies main oil pump running for RFPT 3B N/A Step 16: Critical Step
[4.3] VERIFY CLOSED 3-FCV-3-12, RFP 3B DISCHARGE VALVE.
SAT Standard:
UNSAT VERIFY CLOSED 3-FCV-3-12, RFP 3B DISCHARGE VALVE.
N/A 11
STEP / STANDARD SAT / UNSAT Step 17:
[4.4] DEPRESS 3-HS-46-9A, RFPT 3B SPEED CONT RAISE/LOWER, Critical Step and VERIFY amber light is illuminated.
SAT Standard:
UNSAT Depresses 3-HS-46-9A N/A Step 18:
[4.5] DEPRESS 3-HS-3-150A, RFPT 3B TRIP RESET. Critical Step Standard: SAT Depresses 3-HS-3-150A and verifies the 3-ZI-1-133 LP Stop Valve and 3- UNSAT FCV-135 HP Stop Valve comes OPEN.
N/A Step 19:
[4.6] PLACE 3-HS-46-138A, RFPT 3B START/LOCAL ENABLE, in Critical Step START.
SAT Standard:
UNSAT Places 3-HS-46-138A in START N/A Step 20:
[4.7] CHECK RFPT 3B speed increases to approximately 600 rpm.
SAT Standard:
UNSAT Verifies RFPT 3B speed increases to approximately 600 rpm N/A 12
STEP / STANDARD SAT / UNSAT Step 21:
[4.8] VERIFY OPEN 3-FCV-3-13, RFP 3B MIN FLOW VALVE. Critical Step Standard: SAT Verifies 3-FCV-3-13 OPEN UNSAT N/A Step 21:
CAUTION RFP discharge pressure is limited to below 1250 psig to avoid system damage.
[4.9] PLACE 3-HS-46-9A, RFPT 3B SPEED CONT RAISE/LOWER in Critical Step RAISE to raise RFPT speed, maintaining discharge pressure less than 1250 psig.
SAT Standard:
UNSAT Raises RFPT speed using Manual Speed Control Handswitch, N/A maintaining discharge pressure <1250 psig as indicated on 3-PI-3-9A RFPT 3B (Only Critical if exceeds 1250 psig, any pressure <1250 psig is acceptable).
STOP TIME END OF TASK 13
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3. The Unit 3 reactor has scrammed and the turbine bypass valves are not responding for pressure control due to a loss of EHC fluid. EOI-1 has been followed to RC/P-4. Reactor water level control is in automatic on RFPT 3C.
INITIATING CUES:
The Unit Supervisor directs you to place 3A RFPT in alternate pressure control, as directed by 3-EOI-APPENDIX-11F and lower Reactor Pressure to low in the pressure band of 800 to 1000 psig.
14
N2 MAKEUP TO PRIMARY CONTAINMENT WITH SITE: BFN JPM TITLE:
2-EOI-APPENDIX-14A JPM NUMBER: 669 U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-77 Lineup nitrogen Makeup to primary TASK NUMBER / TASK TITLE(S):
Containment IAW EOI-APPENDIX-14A K/A RATINGS: RO: 3.7SRO: 3.8 223001 Primary Containment System and Auxiliaries A2.04; Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT SYSTEM AND AUXILIARIES ; and K/A No. &STATEMENT: (b) based on those predictions, use procedures to correct, control, or mitigate the consequences ofthose abnormal conditions or operations: High containment/drywell hydrogen concentration RELATED PRA INFORMATION: None SAFETY FUNCTION: 5 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _669 U2__
TASK STANDARD: Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration.
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 2-EOI-APPENDIX-14A VERIFICATION TIME: 15 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 285
- 1. Open Schedule File
- 2. Open Event File
- 3. Reset to IC-28 and take out of freeze.
Console
- 6. Fire Trigger 2 Operator
- 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch Instructions in BYPASS per EOI APPDX 19
- 9. Wait for Group 6 schedule file to time out and alrms to settle
- 10. Freeze simulator and save IC.
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 2 100 0 Yes INSIDE DRYWELL TH23 FUEL CLADDING 2 100% 0 N/A DAMAGE RC08 RCIC STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE HP04 HPCI STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE CS04A CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV II RD01A CRD PUMP TRIP 1 N/A 0 N/A 2A RD01B CRD PUMP TRIP 1 N/A 0 N/A 2B FW01A CONDENSATE 1 N/A 0 N/A PUMP TRIP 2A FW01B CONDENSATE 1 N/A 0 N/A 3
PUMP TRIP 2B FW01C CONDENSATE 1 N/A 0 N/A PUMP TRIP 2C PC08 H2 IN DRYWELL_ 2 29 0 N/A PC09 OXYGEN IN 2 2.8 0 N/A DRYWELL_
PC10 H2 IN 2 18 0 N/A SUPPRESSION POOL_
PC11 OXYGEN IN 2 1.5 0 N/A SUPPRESSION POOL_
Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set ZLOXA554C9 DW EQUIP DRAIN 2 N/A N/A ON SUMP LEVEL ABNORMAL Schedule File(s):
- JPM 669 U2 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.sch
- Appendix\App. 8E.sch
- JPM 669 U2 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.evt 4
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/15 All Initial issue 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is shutdown.
- 2-EOI-APPENDIX-12has been completed
- 2-EOI-APPENDIX-19 has been completed.
- PCIS Group 6 has been overridden per 2-EOI-APPENDIX-8E.
INITIATING CUES:
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2-EOI-APPENDIX-14A beginning on step 2.
6
START TIME STEP / STANDARD SAT / UNSAT Step 1:
- 2. MONITOR Drywell and Suppression Chamber H2 and O2concentrations on one or more of the following displays(2-EOI Appendix 19):
- 2-MON-76-110, H2/O2 ANALYZER (Panel 2-9-55)
UNSAT
- 2-XR-76-110, H2/O2 CONCENTRATION (Panel 2-9-54)
N/A Standard:
Verifies H2 and O2 concentrations Step 2:
- 3. IF ................. Drywell/Suppression Chamber H2 /O2 analyzer is or becomes inoperable, SAT THEN ...........NOTIFY Chemistry Lab to sample Drywell andSuppression Chamber for H2 and O2 using CI-644.
UNSAT Standard:
N/A Verifies Drywell/Suppression Chamber H2 /O2 analyzers are Operable 7
STEP / STANDARD SAT / UNSAT Step 3:
4.WHEN ......... Drywell or Suppression Chamber H2 or O2 concentration is increasing,THEN ........... CONTINUE in this procedure. SAT Standard: UNSAT Observes a rise in Drywell H2 Concentration and continues with N/A procedure.
Step 4:
NOTE This procedure assumes that the normal makeup is from N2 Storage Tank B.
- 5. DISPATCH personnel to N2 Storage Tank B to CHECK 0-PI-76-331, UNSAT N2 TANK B PRESSURE INDICATOR between 160 and 190 psig.
N/A Standard:
Dispatches UO to verifyN2 Storage Tank B Pressure CUE: N2 Storage Tank B Pressure is reading 180 psig Step 5:
- 6. DETERMINE area with highest H2 and/or O2 concentrations and Critical Step INFORM SRO.
SAT Standard:
UNSAT Correctly determines highest concentration is in the drywell and informs US N/A CUE: If asked about 15 minute sample time, state 15 minutes have elapsed 8
STEP / STANDARD SAT / UNSAT Step 6:
Critical Step
- 7. VERIFY PCIS RESET (Panel 2-9-4).
SAT Standard:
UNSAT Verifies PCIS RESET on Panel 2-9-4 N/A Step 7:
Critical Step
- 8. IF ................. It is desired to makeup N2 to the Suppression Chamber,THEN ...........CONTINUE in this procedure at Step 10. SAT Standard: UNSAT Correctly determine step is not applicable and proceeds to step 9. N/A Step 8:
- 9. CONTROL Drywell H2 and O2 as follows:
Critical Step
- a. OPEN the following valves to admit N2 to Drywell (Panel 2-9-3):
- 2-FCV-76-18, DRYWELL N2 MAKEUP INBDISOLATION VLV
N/A OPENS 2-FCV-76-18, DRYWELL N2 MAKEUP INBD ISOLATION VLV &
2-FCV-76-17, PRI CTMT N2 MAKEUP OUTBD ISOLATION VLV Step 9:
- b. SLOWLY ADJUST 2-PC-76-14, DW/SUPPR CHBR N2 MU Critical Step PRESS CONTROL (Panel 2-9-3), to maintain flow > 55 and
<60 scfm on 2-XR-76-14, DW/SUPPR CHBR N2 MAKEUP SAT FLOW/PRESS (Panel 2-9-3), or as directed by SRO if SAMG execution is in progress.
UNSAT Standard:
N/A Achieves a flowrate between 55-60 scfm and monitors Drywell Hydrogen Concentration Lowering 9
STEP / STANDARD SAT / UNSAT Step 10:
- c. CONTINUEN2 admission to the Drywell UNTIL Drywell H2 andO2 are SAT below desired values.
UNSAT Standard:
N/A Monitors Drywell Hydrogen Concentration Note to Examiner: Once satisfied with N2 Flow established between 55 - 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task.
Pass/ Fail Criteria: Establish N2 Flow> 55 scfm and H2 Concentration on a downward trend.
STOP TIME END OF TASK 10
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is shutdown.
- 2-EOI-APPENDIX-12 has been completed
- 2-EOI-APPENDIX-19 has been completed.
- PCIS Group 6 has been overridden per 2-EOI-APPENDIX-8E.
INITIATING CUES:
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 2-EOI-APPENDIX-14A beginning on step 2.
11
N2 MAKEUP TO PRIMARY CONTAINMENT WITH 3-SITE: BFN JPM TITLE:
EOI-APPENDIX-14A JPM NUMBER: 670 U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-77 Lineup nitrogen Makeup to primary TASK NUMBER / TASK TITLE(S):
Containment IAW EOI-APPENDIX-14A K/A RATINGS: RO: 3.7SRO: 3.8 223001 Primary Containment System and Auxiliaries A2.04; Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT SYSTEM AND AUXILIARIES ; and K/A No. &STATEMENT: (b) based on those predictions, use procedures to correct, control, or mitigate the consequences ofthose abnormal conditions or operations: High containment/drywell hydrogen concentration RELATED PRA INFORMATION: None SAFETY FUNCTION: 5 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _670 U3_
TASK STANDARD: Perform operations necessary to establish Nitrogen Makeup to Primary Containment and lower Primary Containment Hydrogen Concentration.
Operator Fundamental evaluated: Monitoring plant conditions and indications closely and controlling plant evolutions precisely.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure: 3-EOI-APPENDIX-14A VERIFICATION TIME:
PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 285
- 1. Open Schedule File
- 2. Open Event File
- 3. Reset to IC-28 and take out of freeze.
Console
- 6. Fire Trigger 2 Operator
- 7. Place H2/O2 Analyzer in service with H2/O2 ISOL BYP Keylock Switch Instructions in BYPASS per EOI APPDX 19
- 9. Wait for Group 6 schedule file to time out and alrms to settle
- 10. Freeze simulator and save IC.
Malfunctions Description Event Severity Delay Initial set TH22 COOLANT LEAK 2 100 0 Yes INSIDE DRYWELL TH23 FUEL CLADDING 2 100% 0 N/A DAMAGE RC08 RCIC STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE HP04 HPCI STEAM 1 N/A 0 N/A SUPPLY VALVE AUTO OPENING FAILURE CS04A CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV I CS04B CORE SPRAY 1 N/A 0 N/A LOGIC POWER FAILURE DIV II RD01A CRD PUMP TRIP 1 N/A 0 N/A 2A RD01B CRD PUMP TRIP 1 N/A 0 N/A 2B 3
FW01C CONDENSATE 1 N/A 0 N/A PUMP TRIP 2C PC08 H2 IN DRYWELL_ 2 29 0 N/A PC09 OXYGEN IN 2 2.8 0 N/A DRYWELL_
PC10 H2 IN 2 18 0 N/A SUPPRESSION POOL_
PC11 OXYGEN IN 2 1.5 0 N/A SUPPRESSION POOL_
Overrides Description Event Severity Delay Initial set ZLOXA554C9 DW EQUIP DRAIN 2 N/A N/A ON SUMP LEVEL ABNORMAL Schedule File(s):
- JPM 669 U3 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.sch
- Appendix\App. 8E.sch
- JPM 669 U3 N2 Makeup to Primary Containment 2-EOI-APPENDIX-14A.evt 4
Revision Summary Rev Effective Pages Description No. Date Affected 0 05/27/15 All Initial issue 5
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is shutdown.
- 3-EOI-APPENDIX-12 has been completed.
- 3-EOI-APPENDIX-19 has been completed.
- PCIS Group 6 has been overridden per 3-EOI-APPENDIX-8E.
INITIATING CUES:
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 3-EOI-APPENDIX-14A beginning on step 2.
6
START TIME STEP / STANDARD SAT / UNSAT Step 1:
- 3. MONITOR Drywell and Suppression Chamber H2 and O2concentrations on one or more of the following displays(3-EOI Appendix 19):
- 3-MON-76-110, H2/O2 ANALYZER (Panel 3-9-55)
UNSAT
- 3-XR-76-110, H2/O2 CONCENTRATION (Panel 3-9-54)
N/A Standard:
Verifies H2 and O2 concentrations Step 2:
- 3. IF ................. Drywell/Suppression Chamber H2 /O2 analyzer is or becomes inoperable, SAT THEN ...........NOTIFY Chemistry Lab to sample Drywell UNSAT andSuppression Chamber for H2 and O2 using CI-644.
N/A Standard:
Verifies Drywell/Suppression Chamber H2 /O2 analyzers are Operable 7
STEP / STANDARD SAT / UNSAT Step 3:
- 4. WHEN ......... Drywell or Suppression Chamber H2 or O2 concentration is increasing,THEN ........... CONTINUE in this procedure. SAT Standard: UNSAT Observes a rise in Drywell H2 Concentration and continues with N/A procedure.
Step 4:
NOTE This procedure assumes that the normal makeup is from N2 Storage Tank B.
- 5. DISPATCH personnel to N2 Storage Tank B to CHECK 0-PI-76-331, UNSAT N2 TANK B PRESSURE INDICATOR between 160 and 190 psig.
N/A Standard:
Dispatches UO to verifyN2 Storage Tank B Pressure CUE: N2 Storage Tank B Pressure is reading 180 psig Step 5:
- 6. DETERMINE area with highest H2 and/or O2 concentrations and Critical Step INFORM SRO.
SAT Standard:
UNSAT Correctly determines highest concentration is in the drywell and informs US N/A CUE: If asked about 15 minute sample time, state 15 minutes have elapsed 8
STEP / STANDARD SAT / UNSAT Step 6:
Critical Step
- 7. VERIFY PCIS RESET (Panel 3-9-4).
SAT Standard:
UNSAT Verifies PCIS RESET on Panel 3-9-4 N/A Step 7:
Critical Step
- 8. IF ................. It is desired to makeup N2 to the Suppression Chamber,THEN ...........CONTINUE in this procedure at Step 10. SAT Standard: UNSAT Correctly determine step is not applicable and proceeds to step 9. N/A Step 8:
- 9. CONTROL Drywell H2 and O2 as follows:
Critical Step
- a. OPEN the following valves to admit N2 to Drywell (Panel 3-9-3):
- 3-FCV-76-18, DRYWELL N2 MAKEUP INBDISOLATION VLV
N/A OPENS 3-FCV-76-18, DRYWELL N2 MAKEUP INBD ISOLATION VLV
&3-FCV-76-17, PRI CTMT N2 MAKEUP OUTBD ISOLATION VLV Step 9:
- b. SLOWLY ADJUST 3-PC-76-14, DW/SUPPR CHBR N2 MUPRESS Critical Step CONTROL (Panel 3-9-3), to maintain flow between 55 and60 scfm on 3-XR-76-14, DW/SUPPR CHBR N2 MAKEUPFLOW/PRESS (Panel 3-SAT 9-3), or as directed by SRO if SAMGexecution is in progress.
UNSAT Standard:
N/A Achieves a flowrate between 55-60 scfm and monitors Drywell Hydrogen Concentration Lowering 9
STEP / STANDARD SAT / UNSAT Step 10:
- c. CONTINUE N2 admission to the Drywell UNTIL Drywell H2 and O2 are below desired values. SAT Standard: UNSAT Monitors Drywell Hydrogen Concentration N/A Note to Examiner: Once satisfied with N2 Flow established between 55 - 60 scfm with a downward trend on H2 Concentration in the Drywell. End of task.
Pass/ Fail Criteria: Establish N2 Flow > 55 scfm and H2 Concentration on a downward trend.
STOP TIME END OF TASK 10
Provide to Applicant IN-SIMULATOR: I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is shutdown.
- 3-EOI-APPENDIX-12 has been completed.
- 3-EOI-APPENDIX-19 has been completed.
- PCIS Group 6 has been overridden per 3-EOI-APPENDIX-8E.
INITIATING CUES:
The Unit Supervisor directs you to lower Hydrogen Concentration by performing 3-EOI-APPENDIX-14A beginning on step 2.
11
Restore Offsite Power to 4KV shutdown board at SITE: BFN JPM TITLE:
PNL 9-23 JPM NUMBER: 631 U2 REVISION: 0 TASK SRO STA UO NAUO APPLICABILITY:
U-082-NO-09 / Restore Offsite Power to 4KV TASK NUMBER / TASK TITLE(S):
shutdown board at PNL 9-23 K/A RATINGS: RO 3.4 SRO 3.4 262001 A.C. Electrical Distribution A4.02 Ability to manually operate and/or monitor in the control room: Synchroscope, K/A STATEMENT:
including understanding of running andincoming voltages RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 6 EVALUATION LOCATION: In -P la n t Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NATIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: 631 U2 RO SRO DATE: _______
TASK STANDARD: Perform operations necessary to restore offsite power to 4KV SD BD A from 4KV SD BUS 1.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure 0-OI-82 VERIFICATION TIME: 15 Min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 286 Console 1. Reset to IC 28 and take out of freeze Operator 2. Start A EDG and parallel with offsite Instructions 3. Open 4-kV Shutdown Board A Breaker 1614 Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set 3
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed.
I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- No Inclement weather currently exists in the area
- 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> ago, 4 KV Shutdown Board A was separated from Offsite Power in accordance with 0-OI-82, Standby Diesel Generator System.
INITIATING CUE:
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board A using the normal feeder breaker and remove DG A from parallel operation in accordance with 0-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23.
4
START TIME STEP / STANDARD SAT /
UNSAT Step 1:
0-OI-82 Standby Diesel Generator System Section 8.3 Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23 NOTE The following list of 4-kV shutdown board normal and alternate feeder breakers may be useful when performing this section:
__UNSAT Shutdown A B C D Board N/A Norm Feed Bkr 1614 1616 1718 1724 Alt Feed Bkr 1716 1714 1624 1618
[1] VERIFY 4-kV Shutdown Board A is being supplied power by its respective Diesel Generator as the only source of power.
Standard:
Verifies 4-kV Shutdown Board A is being supplied by DG A.
Step 2:
[2] VERIFY the associated 4kV shutdown board auto transfer lockout relay is tripped to MANUAL.
Diesel Handswitch Name Handswitch Panel SAT No.
4KV SD BD A UNSAT A 0-211-3EA 0-9-23-7 AUTO/LOCKOUT RESET N/A Standard:
Verifies 4KV SD BD A AUTO/LOCKOUT RESET, HS-0-211-A, is tripped to manual.
5
STEP / STANDARD SAT /
UNSAT Step 3:
[3] PLACE the synchroscope switch for the 4-kV shutdown board Critical Step feeder breaker that is to be paralleled with the Diesel Generator in ON. SAT Standard: UNSAT Places Synchroscope switch for 4-kV Shutdown Board A normal N/A feeder breaker 1614 to ON.
Step 4:
[4] VERIFY 4-kV Shutdown Bus 1(2) voltage is between 3950 Volts SAT and 4400 Volts and NOT undergoing abnormal voltage transients.
UNSAT Standard:
N/A Verifies 4-kV Shutdown Bus 1 voltage is between 3950 Volts and 4400 Volts and NOT undergoing abnormal voltage transients.
Step 5:
[5] VERIFY associated incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients.
Shutdown Instrument Name Instrument No. Panel Bd SAT A or B GEN SYNC 0-SI-82-0AB 0-9-23-7 FREQUENCY UNSAT C or D GEN SYNC 0-SI-82-0CD 0-9-23-8 FREQUENCY N/A Standard:
Verifies incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients using GEN SYNC FREQUENCY,0-SI-82-AB.
6
STEP / STANDARD SAT /
UNSAT Step 6:
CAUTION DO NOT parallel the Diesel Generators with an unstable offsite source or during inclementweather (e.g., lightning, heavy winds).
[6] IF 4-kV Shutdown Bus 1 (2) is experiencing abnormal voltage or UNSAT frequency conditions, THEN PERFORM the following:
N/A Standard:
STEP N/A Step 7:
CAUTION Only one Unit 1 and 2 Diesel Generator at a time is allowed to be operated in parallel with system.
Critical Step
[7] PULL and PLACE the associated Diesel Generator mode selector switch in PARALLELED WITH SYSTEM. SAT Diesel Handswitch Name Handswitch Panel UNSAT No.
A DG A MODE SELECT 0-HS-82-A/5A 0-9-23-7 N/A Standard:
Pulls DG A MODE SELECT switch 0-HS-82-A/5A and places it in PARALLELED WITH SYSTEM.
7
STEP / STANDARD SAT /
UNSAT Step 8:
CAUTION Failure of the PARALLELED WITH SYSTEM light to illuminate in the following step could indicate that the DG is still in SINGLE UNIT operation and result in overload when the DG output breaker is closed.
SAT UNSAT
[8] RELEASE the Diesel Generator mode selector switch and OBSERVE PARALLELED WITH SYSTEM light illuminated.
N/A Standard:
Releases the Diesel Generator A mode selector switch, 0-HS A/5A and observesPARALLELED WITH SYSTEM light is illuminated.
Step 9:
[9] ADJUST Diesel Generator frequency using the associated Diesel Generator governor control switch to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction.
Critical Step Diesel Handswitch Name Handswitch Panel No. SAT A DG A GOVERNOR 0-HS-82-A/3A 0-9-23-7 CONTROL UNSAT Standard: N/A AdjustsDiesel Generator A frequency using Diesel Generator governor control switch, 3-HS-82-A/3A, (in lower direction) to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction.
8
STEP / STANDARD SAT /
UNSAT Step 10:
[10] USE the associated Diesel Generator voltage regulator control switch to match Diesel Generator and System voltages.
Diesel Instrument Name Inst No. Panel DG A VOLT REGULATOR 0-HS-82-A/2A SAT CONT A GEN SYNC REF VOLTAGE 0-EI-82-AB 0-9-23-7 UNSAT SYSTEM SYNC REF 0-EI-211-0AB VOLTAGE N/A Standard:
Matches DG A voltage with system voltage using DG A VOLT REGULATOR CONT switch 0-HS-82-A/2A.
Step 11:
[11] WHEN the synchroscope needle is approximately 2 minutes on Critical Step the right hand side of the 12 o'clock position, THEN CLOSE the 4-kV shutdown board feeder breaker that is to be SAT paralleled with the Diesel Generator.
UNSAT Standard:
N/A Closesthe 4-kV shutdown board feeder breaker 1614 when the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position.
Step 12:
[12] PLACE the synchroscope switch for the 4-kV shutdown board SAT feeder breaker that was paralleled with the Diesel Generator in OFF.
UNSAT Standard:
N/A Places the synchroscope switch for BKR 1614 in OFF.
9
STEP / STANDARD SAT /
UNSAT Step 13:
NOTE If diesel operates greater than 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> at less than 50% load, the diesel should be loaded to full load for at least 30 minutes prior to engine shutdown. This will allow the engine to clean out any oil accumulations from the exhaust manifolds.
[13] IF DG has been operating at a low-load condition (50%) for an extended period of time (4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br />) THEN PERFORM the following (Otherwise N/A):
[13.1] USE the associated Diesel Generator's governor controlswitch and voltage regulator control switch toINCREASE kW and kVAR load, in increments of Critical Step 100kWevery 15 minutes.
SAT Diesel Handswitch Name Hands Panel witch UNSAT No.
DG A GOVERNOR CONTROL 0-HS-N/A 82-A/3A A 0-9-23-7 DG A VOLT REGULATOR 0-HS-CONTROL 82-A/2A
[13.2] OBSERVE the exhaust stack smoke concentration from outside the DG room after each incremental increase.
[13.3] STEP N/A
[13.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible.
[13.5] MAINTAIN 100% load for a minimum of 30 minutes.
Standard:
Loads DG to 2600 kW and 1850 kVAR by using 0-HS-82-A/3A and 0-HS-82-A/2A handswitches.
CUE: After first 100 kW load adjustment state 15 minutes have elapsed and no observable black smoke from exhaust stack for time compression and continue to full load.
10
STEP / STANDARD SAT /
UNSAT Step 14:
NOTE Lagging VARs should be maintained when adjusting kW load (rising or lowering). This may require kW load adjustment to be stopped periodically to allow for adjusting kVAR load. Once desired kW load is achieved, Illustration 1 should be referred to for determination of kVAR loading required to obtain a power factor (pf) of 0.8 lagging. Diesel generator kVAR load should then be adjusted to obtain a 0.8 pf lagging. IF system conditions will NOT permit the kVAR loading required to obtain a 0.8 pf lagging, kVAR load should be adjusted to the maximum kVAR lagging the system will allow.
SAT UNSAT
[14] USE the associated Diesel Generator's governor control switch and voltage regulator control switch to obtain desired kW and N/A kVAR load.
Diesel Handswitch Name Handswitch No. Panel DG A GOVERNOR CONTROL 0-HS-82-A/3A A 0-9-23-7 DG A VOLT REGULATOR CONT 0-HS-82-A/2A Standard:
Obtains desired kW and kVAR load using DG A Governor Control switch, 0-HS-82-A/3A and DG Volt Regulator Cont switch, 0-HS-82-A/2A.
CUE: state 30 minutes have elapsed continue with procedure.
Step 15:
[15] MONITOR the offsite source that is paralleled with the Diesel Generator. SAT
[16] IF abnormal voltage or frequency transients are experienced, UNSAT THEN N/A Standard:
Step is N/A 11
STEP / STANDARD SAT /
UNSAT Step 16:
[17] WHEN Parallel with System operation is no longer desired, THEN UNLOAD the Diesel Generator as follows:
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVARlimit may result in a reverse power trip of the Diesel Generator output breaker.
[17.1] USE the associated Diesel Generator's governor control Critical Step switch and voltage regulator control switch to reduce generator load to approximately 300 kW and SAT 250 kVAR:
UNSAT Diesel Instrument Name Inst No. Panel N/A DG A GOVERNOR CONTROL 0-HS-82-A/3A DG A VOLTAGE 0-HS-82-A/2A A REGULATOR CONTROL 0-9-23-7 DG A KILOWATTS 0-JI-82-A/A DG A KILOVARS 0-VAR-82-A/A Standard:
Unloads the DG to approximately 300 KW and 250 kVAR.
Step 17
[17.2] PLACE the associated Diesel Generator breaker control Critical Step switch in TRIP SAT Diesel Handswitch Name Handswitch No. Panel A DG A BKR 1818 0-HS-211-A/22A 0-9-23-7 UNSAT N/A Standard:
Trips Diesel Generator breaker 1818.
12
STEP / STANDARD SAT /
UNSAT Step 18:
[17.3] PULL and PLACE the associated Diesel Generator mode Critical Step selector switch in SINGLE UNIT.
SAT Diesel Handswitch Name Handswitch No. Panel A DG A MODE SELECT 0-HS-211-A/5A 0-9-23-7 UNSAT N/A Standard:
Pulls and places 0-HS-211-A/5A to Single Unit.
Step 19:
[17.4] RELEASE the Diesel Generator mode selector switch and SAT OBSERVE the SINGLE UNIT light illuminated.
UNSAT Standard:
N/A Verifies Single Unit light illuminated.
CUE: ANOTHER OPERATOR WILL CONTINUE FROM HERE STOP TIME END OF TASK 13
Provide to Applicant INITIAL CONDITIONS:
You are an Operator on Unit 2.
- No Inclement weather currently exists in the area
- 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> ago, 4 KV Shutdown Board A was separated from Offsite Power in accordance with 0-OI-82, Standby Diesel Generator System.
INITIATING CUE:
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board A using the normal feeder breaker and remove DG A from parallel operation in accordance with 0-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23.
14
Restore Offsite Power to 4KV shutdown board at PNL 9-SITE: BFN JPM TITLE:
23 U-3 JPM NUMBER: 631 REVISION: 0 TASK SRO STA UO NAUO APPLICABILITY:
U-082-NO-09 / Restore Offsite Power to 4KV TASK NUMBER / TASK TITLE(S):
shutdown board at PNL 9-23 K/A RATINGS: RO 3.4 SRO 3.4 262001 A.C. Electrical Distribution A4.02 Ability to manually operate and/or monitor in the control K/A STATEMENT: room: Synchroscope, including understanding of running and incoming voltages RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 6 EVALUATION LOCATION: In -P la n t Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: 631 RO SRO DATE: _______
TASK STANDARD: Perform operations necessary to restore offsite power to 4KV SD BD EC.
PRA: NA REFERENCES/PROCEDURES NEEDED: Procedure 3-OI-82 VERIFICATION TIME: 15 Min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 286
- 1. Reset to IC 28 and take out of freeze Console
- 2. Start C EDG and parallel with offsite Operator
- 3. Open 4-kV Shutdown Board 3EC Breaker 1338 Instructions Malfunctions Description Event Severity Delay Initial set Remotes Description Event Severity Delay Initial set Overrides Description Event Severity Delay Initial set Batch / Pref File(s):
3
IN-SIMULATOR: I will explain the initial conditions and state the task to be performed.
I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- No Inclement weather currently exists in the area
- 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> ago, 4 KV Shutdown Board 3EC was separated from Offsite Power in accordance with 3-OI-82, Standby Diesel Generator System.
INITIATING CUE:
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board 3EC using the normal feeder breaker and remove DG 3C from parallel operation in accordance with 3-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23.
4
START TIME STEP / STANDARD SAT /
UNSAT Step 1:
3-OI-82 Standby Diesel Generator System Section 8.3 Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23 NOTE The following list of 4-kV shutdown board normal and alternate feeder breakers may be useful when performing this section:
SAT UNSAT Shutdown 3EA 3EB 3EC 3ED Board N/A Norm Feed Bkr 1334 1336 1338 1342 Alt Feed Bkr 1726 1728 1626 1628
[1] VERIFY 4-kV Shutdown Board 3EC is being supplied power by its respective Diesel Generator as the only source of power.
Standard:
Verifies 4-kV Shutdown Board EC is being supplied by DG C Step 2:
[2] VERIFY the associated 4kV shutdown board auto transfer lockout relay is tripped to MANUAL.
SAT Diesel Handswitch Name Handswitch No. Panel 4KV SD BD 3EC 3-43-211- UNSAT 3C 3-9-23 AUTO/LOCKOUT RESET 3EC N/A Standard:
Verifies 4KV SD BD 3EC AUTO/LOCKOUT RESET, 3-43-211-3EC, is tripped to manual.
5
STEP / STANDARD SAT /
UNSAT Step 3:
[3] PLACE the synchroscope switch for the 4-kV shutdown board Critical Step feeder breaker that is to be paralleled with the Diesel Generator in ON. SAT Standard: UNSAT Places Synchroscope switch for 4-kV Shutdown Board EC normal N/A feeder breaker 1338 to ON Step 4:
[4] CHECK the applicable 4-kV unit board (4-kV bus tie board)
SAT voltage is between 3950 VOLTS and 4400 VOLTS and NOT undergoing abnormal voltage transients.
UNSAT Standard:
N/A Verifies 4-kV Unit Board voltage is between 3950 Volts and 4400 Volts and NOT undergoing abnormal voltage transients.
Step 5:
[5] VERIFY associated incoming frequency is between 59 HERTZ and 61 HERTZ and NOT undergoing abnormal frequency transients.
Shutdown Instrument Name Instrument No. Panel SAT Bd 3EA or GEN SYNC 3-SI-82-3AB 3-9-23 UNSAT 3EB FREQUENCY 3EC or GEN SYNC 3-SI-82-3CD 3-9-23 N/A 3ED FREQUENCY Standard:
Verifies incoming frequency is between 59 Hertz and 61 Hertz and NOT undergoing abnormal frequency transients using GEN SYNC FREQUENCY, 3-SI-82-CD .
6
STEP / STANDARD SAT /
UNSAT Step 6:
CAUTION DO NOT parallel the Diesel Generators with an unstable offsite source or during inclement weather (e.g., lightning, heavy winds). SAT UNSAT
[6] IF 4-kV unit board (4-kV bus tie board) is experiencing abnormal voltage or frequency conditions, THEN PERFORM the following: N/A Standard:
N/A Step 7:
CAUTION Only one Unit 1 and 2 Diesel Generator at a time is allowed to be operated in parallel with system.
Critical Step
[7] PULL and PLACE the associated Diesel Generator mode SAT selector switch in PARALLELED WITH SYSTEM.
UNSAT Diesel Handswitch Name Handswitch Panel No.
N/A 3C DG 3C MODE SELECT 3-HS-82-3C/5A 3-9-23 Standard:
Pulls DG 3C MODE SELECT switch 3-HS-82-3C/5A and places it in PARALLELED WITH SYSTEM 7
STEP / STANDARD SAT /
UNSAT Step 8:
CAUTION Failure of the PARALLELED WITH SYSTEM light to illuminate in the following step could indicate that the DG is still in SINGLE UNIT operation and result in overload when the DG output breaker is closed. SAT UNSAT
[8] RELEASE the Diesel Generator mode selector switch and OBSERVE PARALLELED WITH SYSTEM light illuminated. N/A Standard:
Releases the Diesel Generator 3C mode selector switch, 3-HS-82-3C/5C and observes PARALLELED WITH SYSTEM light is illuminated.
Step 9:
[9] ADJUST Diesel Generator frequency using the associated Diesel Generator governor control switch to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction.
Critical Step Diesel Handswitch Name Handswitch Panel No. SAT 3C DG 3C GOVERNOR 3-HS-82-3C/3A 3-9-23 CONTROL UNSAT Standard: N/A Adjusts Diesel Generator 3C frequency using Diesel Generator governor control switch, 3-HS-82-3C/3A (in lower direction) to obtain a synchroscope needle rotation of one revolution every 15 to 20 seconds in the SLOW direction.
8
STEP / STANDARD SAT /
UNSAT Step 10:
[10] USE the associated Diesel Generator voltage regulator control switch to match Diesel Generator and System voltages.
Dies Instrument Name Inst No. Panel el SAT DG 3C VOLT REGULATOR 3-HS CONT 3C/2A UNSAT 3C GEN SYNC REF VOLTAGE 3-EI-82-3CD 3-9-23 SYSTEM SYNC REF 3-EI-211-VOLTAGE 3ECB/B N/A Standard:
Matches DG C voltage with system voltage using DG 3C VOLT REGULATOR CONT switch 3-HS-82-3C/2A Step 11:
[11] WHEN the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position, THEN Critical Step CLOSE the 4-kV shutdown board feeder breaker that is to be SAT paralleled with the Diesel Generator.
UNSAT Standard:
N/A Closes the 4-kV shutdown board normal feeder breaker 1338 when the synchroscope needle is approximately 2 minutes on the right hand side of the 12 o'clock position.
Step 12:
[12] PLACE the synchroscope switch for the 4-kV shutdown board SAT feeder breaker that was paralleled with the Diesel Generator in OFF. UNSAT Standard: N/A Places the synchroscope switch for BKR 1338 in OFF 9
STEP / STANDARD SAT /
UNSAT Step 13:
[13] IF the normal feeder breaker is supplying the 4-kV shutdown board, THEN RESET the associated 4kV shutdown board auto transfer lockout Critical Step relay.
SAT Diesel Handswitch Name Handswitch Panel No.
UNSAT 3C 4KV SD BD 3EC 3-43-211-3EC 3-9-23 AUTO/LOCKOUT N/A RESET Standard:
Resets 4KV SD BD 3EC Auto Transfer Lockout Relay Step 14:
NOTE If diesel operates greater than 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> at less than 50% load, the diesel should be loaded to full load for at least 30 minutes prior to engine shutdown. This will allow the engine to clean out any oil accumulations from the exhaust manifolds.
[14] IF DG has been operating at a low-load condition (50%) for an extended period of time (4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br />) THEN PERFORM the following (Otherwise N/A): Critical Step
[14.1] USE the associated Diesel Generators governor control SAT switch and voltage regulator control switch to INCREASE kW and kVAR load, in increments of 100kW every 15 UNSAT minutes.
N/A Diesel Handswitch Name Hands Panel witch No.
DG 3C GOVERNOR CONTROL 3-HS-82-3C/3A 3C 3-9-23 DG 3C VOLT REGULATOR 3-HS-CONTROL 82-3C/2A 10
STEP / STANDARD SAT /
UNSAT Step 14 continued:
[14.2] OBSERVE the exhaust stack smoke concentration from outside the DG room after each incremental increase.
[14.3] STEP N/A
[14.4] WHEN smoke becomes relatively clear, CONTINUE to load DG engine to 100% if possible.
[14.5] MAINTAIN 100% load for a minimum of 30 minutes.
Standard:
Loads DG to 2600 kW and 1850 kVAR by using 0-HS-82-A/3A and 0-HS-82-A/2A handswitches.
CUE: After first 100 kW load adjustment state 15 minutes have elapsed and no observable black smoke from exhaust stack for time compression and continue to full load.
Step 15:
NOTE VARs lagging should be maintained when adjusting kW load (rising or lowering). This may require kW load adjustment to be stopped periodically to allow for adjusting kVAR load. Once desired kW load is achieved, Illustration 1 should be referred to for determination of kVAR loading required to obtain a power factor (pf) of 0.8 lagging. Diesel generator kVAR load should then be adjusted to obtain a 0.8 pf lagging. IF system conditions will NOT permit the kVAR loading required to obtain a 0.8 pf lagging, kVAR load should be adjusted to SAT the maximum kVAR lagging the system will allow.
UNSAT
[15] USE the associated Diesel Generator's governor control switch N/A and voltage regulator control switch to obtain desired kW and kVAR load.
Diesel Handswitch Name Handswitch No. Panel DG 3C GOVERNOR 3-HS CONTROL 3C/3A 3C 3-9-23 DG 3C VOLT REGULATOR 3-HS CONT 3C/2A 11
STEP / STANDARD SAT /
UNSAT Standard:
Obtains desired kW and kVAR load using DG 3C Governor Control switch, 3-HS-82-3C/3A and DG Volt Regulator Control switch, 3-HS-82-3C/2A CUE: state 30 minutes have elapsed continue with procedure.
Step 16:
[16] MONITOR the offsite source that is paralleled with the Diesel Generator. SAT
[17] IF abnormal voltage or frequency transients are experienced, UNSAT THEN N/A Standard:
Step is N/A Step 17:
[18] WHEN Parallel with System operation is no longer desired, THEN UNLOAD the Diesel Generator as follows:
CAUTION When unloading the Diesel Generator, failure to slowly approach the 300 kW/250 kVAR limit may result in a reverse power trip of the Diesel Generator output breaker. Critical Step SAT
[18.1] USE the associated Diesel Generator's governor control switch and voltage regulator control switch to reduce UNSAT generator load to approximately 300 kW and 250 kVAR: N/A Diesel Instrument Name Inst No. Panel DG 3C GOVERNOR CONTROL 3-HS-82-3C/3A DG 3C VOLT REGULATOR 3-HS-82-3C/2A 3C 3-9-23 CONT DG 3C KILOWATTS 3-JI-82-3C/A DG 3C KILOVARS 3-VAR-82-3C/A 12
STEP / STANDARD SAT /
UNSAT Step 17 continued:
Standard:
Unloads the DG to approximately 300 KW and 250 kVAR Step 18:
[18.2] PLACE the associated Diesel Generator breaker control Critical Step switch in TRIP.
SAT Diesel Handswitch Name Handswitch No. Panel 3C DG 3C BKR 1832 3-HS-211- 3-9-23 UNSAT 3EC/10A N/A Standard:
Trips breaker DG 3C BKR 1832 Step 19:
[18.3] PULL and PLACE the associated Diesel Generator mode Critical Step selector switch in SINGLE UNIT.
SAT Diesel Handswitch Name Handswitch No. Panel 3C DG 3C MODE SELECT 3-HS-82-3C/5A 0-9-23 UNSAT Standard: N/A Pulls and places 3-HS-82-3C/5A to Single Unit Step 20: SAT
[18.4] RELEASE the Diesel Generator mode selector switch and UNSAT OBSERVE the SINGLE UNIT light illuminated.
N/A Standard:
Verifies Single Unit light illuminated CUE: ANOTHER OPERATOR WILL CONTINUE FROM HERE STOP TIME END OF TASK 13
Provide to Applicant INITIAL CONDITIONS:
You are an Operator on Unit 3.
- No Inclement weather currently exists in the area
- 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> ago, 4 KV Shutdown Board 3EC was separated from Offsite Power in accordance with 3-OI-82, Standby Diesel Generator System.
INITIATING CUE:
The Unit Supervisor has directed you to restore offsite power to 4KV Shutdown Board 3EC using the normal feeder breaker and remove DG 3C from parallel operation in accordance with 3-OI-82, Section 8.3, Restoring Offsite Power to 4-kV Shutdown Board at Panel 9-23.
14
SITE: BFN JPM TITLE: Respond to Off-Gas Post Treatment Radiation HI-HI-HI JPM NUMBER: 190 U2 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-066-AB-02 -Respond to Off-Gas Post Treatment TASK NUMBER / TASK TITLE(S):
Radiation Hi-Hi-Hi K/A RATINGS: RO 2.9 SRO 3.2 271000 Offgas System: A2.16; Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those K/A STATEMENT: predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2)
RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: N/A TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: 190 U2 RO SRO DATE: _______
TASK STANDARD: Respond to Off-Gas Post Treatment Radiation HI-HI-HI per 2-AOI-66-2 and/or 2-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-66-2, 2-ARP-9-4C/35 VALIDATION TIME: 15 Minutes PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 287
- 1. Reset to IC 28 Console 2. Fire Manual Trigger 2 Operator 3. Fire Manual Trigger 1 Instructions 4. Station 2nd operator to respond to alarms Malfunctions Description Event Severity Delay Initial set TH23 FUEL CLADDING 1 50 N/A YES DAMAGE RM14C OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURERM 265A RM14D OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-266A Remotes Description Event Severity Delay Initial set OG06 Bypass FCV-66-28 2 N/A N/A BYP Post Treatment Hi-Hi-Hi Rad Isol Overrides Description Event Severity Delay Initial set ZAORI9014A RX BLDG AREA 1 2.5 N/A YES RAD ZAORI9017A RX BLDG AREA 1 2.6 N/A YES RAD ZAORM90265A 90-265 METER 1 6.0 N/A YES UPSCALE ZAORM90266A 90-266 METER 1 6.0 N/A YES UPSCALE ZAORR90135R1 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90135R2 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZLORM90265A_1 90-265 DRAW LITE 1 N/A N/A YES 3
ZLORM90265A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_4 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_4 90-265 DRAW LITE 1 N/A N/A YES XA553A5 OG PRETREAT 1 N/A N/A YES RAD HI XA553A6 STACK GAS RAD 1 N/A N/A YES HI HI XA553A7 MSL RAD HI 1 N/A N/A YES XA553A13 STACK GAS RAD 1 N/A N/A YES HI XA553A27 MSL RAD HI HI 1 N/A N/A YES XA554C26 CARBON BED 1 N/A N/A YES VAULT RAD HI XA554C27 OG ANNUAL 1 N/A N/A YES RELEASE LIMIT EXCEEDED XA554C33 OG POST TREAT 1 N/A N/A YES RAD HI XA554C34 OG POST TREAT 1 N/A N/A YES RAD HI HI XA554C35 OG POST TREAT 1 N/A N/A YES RAD HI HIHI ZDIHS6628 66-28 VALVE 1 N/A N/A YES CLOSED ZAORR90265R1 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90265R2 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZAORR90160R1 OG PRETREAT 1 -2.0 N/A YES RECORDER UPSCALE XA554B2 RWCU FILTER 1 N/A N/A YES INLET CNDT HIGH Schedule File(s): JPM 190 U2 OG Post treat Rad HI HIHI 4
IN-SIMULATOR:
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are the Unit 2 Operator. Unit 2 is at 100% power.
INITIATING CUE:
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 2-XA-55-4C, window 35.
5
START TIME STEP / STANDARD SAT / UNSAT Performance Step 1:
SAT When directed, identify/obtain copy of ARP-9-4C, window 35.
UNSAT Standard:
N/A Obtains copy of 2-ARP-9-4C, window 35 Examiner Note: Candidate may recognize the annunciator as an entry condition and go directly to 2-AOI-66-2. In that event, continue at Performance Step 5.
Performance Step 2:
2-ARP-9-4C window 35 Operator Action:
A. VERIFY alarm condition on the following
- OFFGAS POST-TREATMENT RADIATION recorder, SAT 2-RR-90-265 on Panel 2-9-2.
- OG POST-TREATMENT CHAN A RAD MON RTMR UNSAT radiationmonitor, 2-RM-90-266A on Panel 2-9-10.
- OG POST-TREATMENT CHAN B RAD MON RTMR N/A radiationmonitor, 2-RM-90-265A on Panel 2-9-10.
Standard:
Verified alarm condition on 2-RR-90-265 and 2-RM-265/266.
Performance Step 3:
B. VERIFY OFF-GAS SYSTEM ISOLATION VALVE, 2-FCV- Critical Step 66-28 has the Mechanical Restraint DISENGAGED and 2-FCV-66-28 isCLOSED. SAT Standard: UNSAT Takes handswitch 2-FCV-66-28 to close and observes green light N/A illuminated and red light out.
Cue: If asked, the Offgas Isolation Valve, 2-FCV-66-28 is NOT mechanically restrained.
6
STEP / STANDARD SAT / UNSAT Performance Step 4:
C. REFER to 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-SAT Hi-Hi UNSAT Standard:
N/A Refers to 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 5:
2-AOI-66-2 4.0 OPERATOR ACTIONS 4.1 Immediate Actions Critical Step
[1] IF scram has not occurred, THEN SAT PERFORM the following:
UNSAT
[1.1] IF core flow is above 60%, THEN N/A REDUCE core flow to between 50-60%.
Standard:
Reduced core flow to between 50-60% with recirc system.
Performance Step 6:
[1.2] MANUALLY SCRAM the Reactor. (Reference 2-AOI-100-1).
Standard:
Critical Step
- Depresses both SCRAM Pushbuttons
- Places mode switch in shutdown SAT
- Verifies All Rods in
- Performs a Scram Announcement UNSAT o Rx Mode Switch Position: Shutdown N/A o Rod Position: All Full In o Reactor Water Level ____ & Trend ___
o Reactor Pressure ____ & Trend ___
o MSIV Position: OPEN o Rx Power: <5%
Examiner Note: The scram report and referring to 2-AOI-100-1 are not considered critical.
7
STEP / STANDARD SAT / UNSAT CUE: Proceed with subsequent actions of 2-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 7:
4.2 Subsequent Actions
[1] IF OFFGAS SYSTEM ISOLATION VALVE, 2-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN SAT DISENGAGE 2-FCV-066-0028 mechanical restraint by UNSAT rotating the restraining handwheel fully in the counterclockwisedirection, locally at the Stack. (Otherwise N/A N/A)
Standard:
Verifies that 2-FCV-066-0028 in NOT mechanically restrained.
Cue: 2-FCV-066 is NOT mechanically restrained.
Performance Step 8:
[2] VERIFY CLOSED OFFGAS SYSTEM ISOLATION VALVE, Critical Step 2-FCV-66-28 on Panel 2-9-53 or locally.
SAT Standard:
UNSAT Verifies 2-FCV-66-28 is closed at panel 9-53 by Verifying RED light above handswitch extinguished and GREEN light above N/A handswitch illuminated. (May have already verified valve closed from the ARP).
Examiner Note: May have already verified valve closed from the ARP Performance Step 9:
[3] MONITOR area radiation levels at Panel: 2-9-11. SAT Standard: UNSAT Monitored radiation levels at Panel 9-11. N/A Cue: Another operator will monitor and evaluate Area Radiation Levels.
8
STEP / STANDARD SAT / UNSAT Performance Step 10:
[4] REFER TO EPIP-1 for emergency classification level and SAT response.
UNSAT Standard; N/A Notifies SM to implement EPIP-1.
Cue: The Shift Manager is implementing the EPIPs as needed.
Performance Step 11:
[5] MONITOR the following parameters:
A. MAIN STEAM LINE RADIATION, 2-RR-90-135, Panel 2-9-2.
B. OFFGAS PRETREATMENT RADIATION 2-RR 157, Pnl 2-9-2. SAT C. OFFGAS POST-TREATMENT RADIATION 2RR- UNSAT 90-265, Pnl 2-9-2 N/A D. STACK GAS RADIATION, 0-RR-90-147, Unit 1 Panel 1-9-2.
Standard; Monitors90-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147.
Cue: As Unit 1 Operator, Stack Gas Radiation, 0-RR-90-147 is reading 5X10E6 cps.
9
STEP / STANDARD SAT / UNSAT Performance Step 12:
[6] IF after five minutes from scram the Offgas Post Treatment activity is not less than 6 x 10E5 cps as indicated on OFFGASRADIATION recorder 2-RR-90-266 on panel 2 Critical Step 2, THEN SAT CLOSE all Main Steam Isolation Valves and Main Steam LineDrain Valves, 2-FCV-1-55 and 2-FCV-1-56.
UNSAT Standard:
N/A Recognizes that the Off-Gas Post Treatment activity is >6 X 10E5 and closes all Main Steam Isolation Valves and Main Steam Line Drain Valves (2-FCV-1-55/56)
Cue: The Unit has been scrammed for 5 minutes.
- Acknowledge closing of MSIVs.
Examiner Note: Closing 1-55 and 1-56 is not considered critical.
Performance Step 13:
NOTE Placing additional Stack Dilution Air Fans in service should keep 0-RM-90-147and 0-RM-90-148 on scale.
[7] PLACE STACK DILUTION FAN SEL control switch, SAT 2-XS-66-29, Panel 2-9-8, in OFF.
UNSAT
[8] START standby STACK DILUTION FAN 2B(2A) using controlswitch, 2-HS-66-31A(29A), Panel 2-9-8. N/A Standard:
Places 2-XS-66-29 in OFF and Starts standby Stack Dilution fan 2B, using 2-HS-66-31A Cue: That completes this task.
STOP TIME _______
END OF TASK 10
Provide to Applicant IN-SIMULATOR:
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are the Unit 2 Operator. Unit 2 is at 100% power.
INITIATING CUE:
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 2-XA-55-4C, window 35.
11
SITE: BFN JPM TITLE: Respond to Off-Gas Post Treatment Radiation HI-HI-HI JPM NUMBER: 190 U3 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-066-AB-02 -Respond to Off-Gas Post Treatment TASK NUMBER / TASK TITLE(S):
Radiation Hi-Hi-Hi K/A RATINGS: RO 2.9 SRO 3.2 271000 Offgas System: A2.16;Ability to (a) predict the impacts of the following on the OFFGAS SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the K/A STATEMENT:
consequences of those abnormal conditions or operations: Loss of offgas system loop seals (2.9/3.2)
RELATED PRA INFORMATION: N/A SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: N/A TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: 190 RO SRO DATE: _______
TASK STANDARD: Respond to Off-Gas Post Treatment Radiation HI-HI-HI per 3-AOI-66-2 and/or 3-ARP-9-4C/35 PRA: NA REFERENCES/PROCEDURES NEEDED: 3-AOI-66-2, 3-ARP-9-4C/35 VALIDATION TIME: 15 Minutes PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____ (Retain entire JPM for records)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
SIMULATOR SETUP IC 28 Exam IC 288
- 1. Reset to IC 28 Console 2. Fire Manual Trigger 2 Operator 3. Fire Manual Trigger 1 Instructions 4. Station 2nd operator to respond to alarms Malfunctions Description Event Severity Delay Initial set TH23 FUEL CLADDING 1 50 N/A YES DAMAGE RM14C OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-265A RM14D OFFGAS RAD 1 1E6 CPS N/A YES MONITOR FAILURE RM-90-266A Remotes Description Event Severity Delay Initial set OG06 Bypass FCV-66-28 2 N/A N/A BYP Post Treatment Hi-Hi-Hi Rad Isol Overrides Description Event Severity Delay Initial set ZAORI9014A RX BLDG AREA 1 2.5 N/A YES RAD ZAORI9017A RX BLDG AREA 1 2.6 N/A YES RAD ZAORM90265A 90-265 METER 1 6.0 N/A YES UPSCALE ZAORM90266A 90-266 METER 1 6.0 N/A YES UPSCALE ZAORR90135R1 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90135R2 90-135 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZLORM90265A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_2 90-265 DRAW LITE 1 N/A N/A YES 3
ZLORM90265A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90265A_4 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_1 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_2 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_3 90-265 DRAW LITE 1 N/A N/A YES ZLORM90266A_4 90-265 DRAW LITE 1 N/A N/A YES XA553A5 OG PRETREAT 1 N/A N/A YES RAD HI XA553A6 STACK GAS RAD 1 N/A N/A YES HI HI XA553A7 MSL RAD HI 1 N/A N/A YES XA553A13 STACK GAS RAD 1 N/A N/A YES HI XA553A27 MSL RAD HI HI 1 N/A N/A YES XA554C26 CARBON BED 1 N/A N/A YES VAULT RAD HI XA554C27 OG ANNUAL 1 N/A N/A YES RELEASE LIMIT EXCEEDED XA554C33 OG POST TREAT 1 N/A N/A YES RAD HI XA554C34 OG POST TREAT 1 N/A N/A YES RAD HI HI XA554C35 OG POST TREAT 1 N/A N/A YES RAD HI HIHI ZDIHS6628 66-28 VALVE 1 N/A N/A YES CLOSED ZAORR90265R1 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 1 ZAORR90265R2 90-265 RECORDER 1 6.0 N/A YES UPSCALE PEN 2 ZAORR90160R1 OG PRETREAT 1 -2.0 N/A YES RECORDER UPSCALE XA554B2 RWCU FILTER 1 N/A N/A YES INLET CNDT HIGH Schedule File(s): JPM 190 U3 OG Post treat Rad HI HIHI 4
IN-SIMULATOR:
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are the Unit 3 Operator. Unit 3 is at 100% power.
INITIATING CUE:
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 3-XA-55-4C, window 35.
5
START TIME STEP / STANDARD SAT / UNSAT Performance Step 1:
SAT When directed, identify/obtain copy of ARP-9-4C, window 35.
UNSAT Standard:
N/A Obtains copy of 3-ARP-9-4C, window 35 Examiner Note: Candidate may recognize the annunciator as an entry condition and go directly to 3-AOI-66-2. In that event, continue at Performance Step 5.
Performance Step 2:
3-ARP-9-4C window 35 Operator Action:
A. VERIFY alarm condition on the following
- OFFGAS POST-TREATMENT RADIATION recorder, SAT 3-RR-90-265 on Panel 3-9-2.
- OG POST-TREATMENT CHAN A RAD MON RTMR UNSAT radiationmonitor, 3-RM-90-266A on Panel 3-9-10.
- OG POST-TREATMENT CHAN B RAD MON RTMR N/A radiationmonitor, 3-RM-90-265A on Panel 3-9-10.
Standard:
Verified alarm condition on 3-RR-90-265 and 3-RM-265/266.
Performance Step 3:
B. VERIFY OFF-GAS SYSTEM ISOLATION VALVE, 3-FCV- Critical Step 66-28 has the Mechanical Restraint DISENGAGED and 3-FCV-66-28 isCLOSED. SAT Standard: UNSAT Takes handswitch 3-FCV-66-28 to close and observes green light N/A illuminated and red light out.
Cue: If asked, the Offgas Isolation Valve, 3-FCV-66-28 is NOT mechanically restrained.
6
STEP / STANDARD SAT / UNSAT Performance Step 4:
C. REFER to 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi SAT Standard: UNSAT Refers to 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi N/A Performance Step 5:
3-AOI-66-2 4.0 OPERATOR ACTIONS 4.1 Immediate Actions Critical Step
[1] IF scram has not occurred, THEN SAT PERFORM the following:
UNSAT
[1.1] IF core flow is above 60%, THEN N/A REDUCE core flow to between 50-60%.
Standard:
Reduced core flow to between 50-60% with recirc system.
Performance Step 6:
[1.2] MANUALLY SCRAM the Reactor. (Reference 3-AOI-100-1).
Standard:
Critical Step
- Depresses both SCRAM Pushbuttons
- Places mode switch in shutdown SAT
- Verifies All Rods in
- Performs a Scram Announcement UNSAT o Rx Mode Switch Position: Shutdown N/A o Rod Position: All Full In o Reactor Water Level ____ & Trend ___
o Reactor Pressure ____ & Trend ___
o MSIV Position: OPEN o Rx Power: <5%
Examiner Note: The scram report and referring to 3-AOI-100-1 are not considered critical.
7
STEP / STANDARD SAT / UNSAT CUE: Proceed with subsequent actions of 3-AOI-66-2, Off-gas Post-treatment Radiation Hi-Hi-Hi Performance Step 7:
4.2 Subsequent Actions
[1] IF OFFGAS SYSTEM ISOLATION VALVE, 3-FCV-066-0028has been mechanically restrained open due to plant conditionsTHEN SAT DISENGAGE3-FCV-066-0028 mechanical restraint by UNSAT rotating the restraining handwheel fully in the counterclockwisedirection, locally at the Stack. (Otherwise N/A N/A)
Standard:
Verifies that 3-FCV-066-0028 in NOT mechanically restrained.
Cue: 3-FCV-066 is NOT mechanically restrained.
Performance Step 8:
[2] VERIFY CLOSED OFFGAS SYSTEM ISOLATION VALVE, Critical Step 3-FCV-66-28 on Panel 3-9-53 or locally.
SAT Standard:
UNSAT Verifies 3-FCV-66-28 is closed at panel 9-53 by Verifying RED light above handswitch extinguished and GREEN light above N/A handswitch illuminated. (May have already verified valve closed from the ARP).
Examiner Note: May have already verified valve closed from the ARP Performance Step 9:
[3] MONITOR area radiation levels at Panel: 3-9-11.
UNSAT Standard:
N/A Monitored radiation levels at Panel 9-11.
Cue: Another operator will monitor and evaluate Area Radiation Levels.
8
STEP / STANDARD SAT / UNSAT Performance Step 10:
[4] REFER TO EPIP-1 for emergency classification level and SAT response.
UNSAT Standard; N/A Notifies SM to implement EPIP-1.
Cue: The Shift Manager is implementing the EPIPs as needed.
Performance Step 11:
[5] MONITOR the following parameters:
A. MAIN STEAM LINE RADIATION, 3-RR-90-135, Panel 3-9-2.
B. OFFGAS PRETREATMENT RADIATION 3-RR 157, Pnl3-9-2. SAT C. OFFGAS POST-TREATMENT RADIATION 3-RR- UNSAT 90-265, Pnl3-9-2 N/A D. STACK GAS RADIATION, 0-RR-90-147, Unit 1 Panel 1-9-2.
Standard; Monitors90-135, 157, and 265. Calls Unit 1 operator for a reading on 0-RR-90-147.
Cue: As Unit 1 Operator, Stack Gas Radiation, 0-RR-90-147 is reading 5X10E6 cps.
9
STEP / STANDARD SAT / UNSAT Performance Step 12:
[6] IF after five minutes from scram the Offgas Post Treatment activity is not less than 6 x 10E5 cps as indicated on OFFGASRADIATION recorder 3-RR-90-265 on panel 3 2, THEN Critical Step CLOSE all Main Steam Isolation Valves and Main Steam SAT LineDrain Valves, 3-FCV-1-55 and 3-FCV-1-56.
UNSAT Standard:
N/A Recognizes that the Off-Gas Post Treatment activity is >6 X 10E5 and closes all Main Steam Isolation Valves and Main Steam Line Drain Valves (3-FCV-1-55/56)
Cue: The Unit has been scrammed for 5 minutes.
- Acknowledge closing of MSIVs.
Examiner Note: Closing 1-55 and 1-56 is not considered critical.
Performance Step 13:
NOTE Placing additional Stack Dilution Air Fans in service should keep 0-RM-90-147and 0-RM-90-148 on scale.
[7] PLACE STACK DILUTION FAN SEL control switch, SAT 3-XS-66-29, Panel 3-9-8, in OFF.
UNSAT
[8] START standby STACK DILUTION FAN 3B(3A) using controlswitch, 3-HS-66-31A(29A), Panel 3-9-8. N/A Standard:
Places 3-XS-66-29 in OFF and Starts standby Stack Dilution fan 3B, using 3-HS-66-31A Cue: That completes this task.
STOP TIME ________
END OF TASK 10
Provide to Applicant IN-SIMULATOR:
I will explain the initial conditions and state the task to be performed. I will provide initiating cues and reports on other actions when directed by you. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's Correct". (OR "That's Incorrect", if applicable). When you have completed your assigned task, you will say, "my task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are the Unit 3 Operator. Unit 3 is at 100% power.
INITIATING CUE:
The Unit Supervisor directs you to respond to an OFF-GAS POST TREATMENT RADIATION HI-HI-HI annunciator, 3-XA-55-4C, window 35.
11
SITE: BFN JPM TITLE: AUTOMATIC START FAILURE OF A & C FIRE PUMPS JPM NUMBER: 673 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-026-NO-01/ MONITOR AUTO START OF FIRE TASK NUMBER / TASK TITLE(S):
PUMP K/A RATINGS: RO: 3.4 SRO: 3.4 286000 Fire Protection System A2.08; Ability to (a) predict the impacts of the following on the FIRE PROTECTION SYSTEM; K/A No. &STATEMENT: and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Failure to actuate when required RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 8 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) Y Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _673A___
TASK STANDARD: Perform operations necessary to manually start A, B and C Fire Pumps.
Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 0-OI-26 VALIDATIONTIME:__15 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 04/28/15 All Initial issue 3
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 1.
- The Reactor Power at 70%
- A Fire Exists on B Reactor Feed Pump Lube Oil Reservoir.
- Fire OPS has been dispatched to the scene.
- Fire Pump B Tagged Out for Maintenance
- A and C Fire Pumps failed to Auto Start.
INITIATING CUES:
The US directs you to start A and C Electric Fire Pumps per 0-OI-26 section 5.4.
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
4
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
[1] PLACE the FIRE PUMP A TRANSFER switch, 0-XS-26-1 in EMERGENCY position, at the respective switchgear.
Critical Step Pump Board Compt A 4160V Shutdown Bd A 11 SAT C 4160V Shutdown Bd C 10 UNSAT Standard:
N/A Simulates placing FIRE PUMP A TRANSFER switch 0-XS-26-3 in EMERGENCY position at 4160 Shutdown Board A, Compartment 11 CUE: FIRE PUMP A TRANSFER switch 0-XS-26-1 is in the EMERGENCY position Step 2:
Critical Step
[2] CLOSE the breaker by placing the FIRE PUMP A CONTROL switch, 0-HS-26-1C to CLOSE. SAT Standard: UNSAT Simulates placing FIRE PUMP A CONTROL switch, 0-HS-26-1C N/A to CLOSE position.
CUE: Breaker Red indicating light is ON with Green and Amber lights are OFF.
Breaker Flag indicates CLOSED with Charging Spring indicating CHARGED.
Step 3:
[3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. SAT Standard UNSAT VERIFIES pump ammeter at breaker indicates between 25 and N/A 40 amps.
CUE: FIRE PUMP A ammeter at breaker indicates 30 amps.
5
Step 4:
[4] PLACE the NORM/EMERG Switch in NORMAL.
SAT Standard UNSAT PLACES the NORM/EMERG Switch in NORMAL for FIRE N/A PUMP A.
CUE: FIRE PUMP A NORM/EMERG Switch is in NORMAL Step 5:
[1] PLACE the FIRE PUMP C TRANSFER switch, 0-XS-26-3 in EMERGENCY position, at the respective switchgear.
Critical Step Pump Board Compt A 4160V Shutdown Bd A 11 SAT C 4160V Shutdown Bd C 10 UNSAT Standard:
N/A Simulates placing FIRE PUMP C TRANSFER switch 0-XS-26-3 in EMERGENCY position at 4160 Shutdown Board C, Compartment 10 CUE: FIRE PUMP C TRANSFER switch 0-XS-26-3 is in the EMERGENCY position Step 5:
Critical Step
[2] CLOSE the breaker by placing the FIRE PUMP C CONTROL switch, 0-HS-26-3C to CLOSE.
SAT Standard:
UNSAT Simulates placing FIRE PUMP C CONTROL switch, 0-HS-26-3C N/A to CLOSE position.
CUE: Breaker Red indicating light is ON with Green and Amber lights are OFF.
Breaker Flag indicates CLOSED with Charging Spring indicating CHARGED.
6
Step 6:
[3] CHECK pump ammeter at breaker indicates between 25 and 40 amps. SAT Standard UNSAT VERIFIES pump ammeter at breaker indicates between 25 and N/A 40 amps.
CUE: FIRE PUMP C ammeter at breaker indicates 30 amps.
Step 7:
[4] PLACE the NORM/EMERG Switch in NORMAL.
SAT Standard UNSAT PLACES the NORM/EMERG Switch in NORMAL for FIRE N/A PUMP C.
CUE: FIRE PUMP C NORM/EMERG Switch is in NORMAL and this completes the JPM.
Termination Criteria: When two Fire Pumps are in service the JPM is complete.
STOP TIME:
7
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 1.
- The Reactor Power at 70%
- A Fire Exists on B Reactor Feed Pump Lube Oil Reservoir.
- Fire OPS has been dispatched to the scene.
- Fire Pump B Tagged Out for Maintenance
- A and C Fire Pumps failed to Auto Start.
INITIATING CUES:
The US directs you to start A and C Electric Fire Pumps per 0-OI-26 section 5.2.
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
8
ALIGNING EMERGENCY EECW MAKEUP TO SPENT SITE: BFN JPM TITLE:
FUEL POOL JPM NUMBER: 674 REVISION: 0 TASK APPLICABILITY: SRO STA UO NAUO U-000-EM-95/ Make-Up To SFP By EECW With TASK NUMBER / TASK TITLE(S):
Fire Hose (Internal Make-Up)
K/A RATINGS: RO: 3.1 SRO: 3.3 233000 Fuel Pool Cooling and Clean-up; A2.02; Ability to (a) predict the impacts of the following on the FUEL POOL COOLING AND CLEAN-UP ; and (b) based on those K/A No. &STATEMENT:
predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Low pool level RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 9 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: __674__
TASK STANDARD: Perform operations necessary to align either North or South Headers of EECW to Unit 2 Spent Fuel Pool.
Operator Fundamental evaluated:
OF-2 Controlling plant evolutions and indications closely.
OF-5 Having a solid understanding of plant design, engineering principles, and sciences.
PRA: NA REFERENCES/PROCEDURES NEEDED: 2-AOI-78-1 VALIDATION TIME: 25 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 0 09/01/15 All Initial issue 3
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is in cold shutdown
- The Unit 2 Spent Fuel Pool water level is lowering.
- Fire Protection is available to assist INITIATING CUES:
The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3].
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
4
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
NOTES
- 1) Hose straps are staged at the hoses at the following locations:
- Unit 1/Unit 2 Reactor Bldg Stairwell, El. 621, R6 U Line (placed on hose to carry weight of charged hose lines).
- Hose reel on the Refuel Floor, El. 664, R6 U Line (for use in securing hose ends as needed).
- 2) Additional hose is stored in a cabinet located in Unit 1/Unit 2 Elevator Room, Reactor Bldg, El 595.
Critical Step CAUTION Performance of this attachment will degrade water chemistry in the SAT Spent Fuel Pool.
UNSAT
[3] UNLOCK and OPEN the following valves:
N/A
- NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792.
- SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793.
Standard:
Simulates opening NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792 and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793 by demonstrating opening each valve counter-clockwise and breaking seal.
CUE: NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0792 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0793 is OPEN Located in stairwell between elevation 565 ft and 593 ft. Hoses are already connected, no tools required.
5
STEP / STANDARD SAT / UNSAT Step 3:
[4] VERIFY charged hoses in stairwell are not obstructing stairway access and/or kinked.
[4.1] ADJUST hose straps, as necessary.
UNSAT Standard:
N/A VERIFIES hoses in stairwell are not kinked Note to Examiner: Hoses are already run along the stairwell. Applicant should verify hoses not kinked and connected.
Step 4:
[5] VERIFY hose connected from NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and route to Unit 2 Spent Fuel Pool Critical Step (El 664, Refuel Floor, R6-U Line).
SAT Standard:
UNSAT VERIFY hose connected from NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and route to Unit 2 Spent N/A Fuel Pool (El 664, Refuel Floor, R6-U Line).
Note to Examiner: Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. Hoses are already connected, no tools required.
Location: Refuel Floor Elevation 664 ft, R U Line.
Step 5:
[6] VERIFY hose connected from SOUTH HDR SPLY TO EMER Critical Step FUEL POOL MU, 1-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664, Refuel Floor, R6-U Line)
SAT Standard:
UNSAT VERIFY hose connected from SOUTH HDR SPLY TO EMER N/A FUEL POOL MU, 1-SHV-067-0797 and route to Unit 2 Spent Fuel Pool (El 664, Refuel Floor, R6-U Line) 6
STEP / STANDARD SAT / UNSAT Note to Examiner: Hoses will be simulated routed to Unit 2 Spent Fuel Pool. Any route to the Unit 2 Spent Fuel Pool is acceptable. Hoses are already connected, no tools required.
Location: Refuel Floor Elevation 664 ft, R U Line.
Step 6:
[7] VERIFY OPEN the following valves (El 664, Refuel Floor, R6 U Line):
- NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-Critical Step 0796.
- SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797.
UNSAT Standard:
N/A Simulates opening NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797 by demonstrating opening each valve counter-clockwise.
CUE: NORTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0796 is OPEN and SOUTH HDR SPLY TO EMER FUEL POOL MU, 1-SHV-067-0797 is OPEN Location: Refuel Floor Elevation 664 ft, R U Line.
Step 7:
[8] VERIFY charged hoses on the Refuel Floor are not kinked.
SAT Standard: UNSAT VERIFY charged hoses on the Refuel Floor are not kinked N/A Termination Criteria: NORTH and SOUTH Header are aligned then the JPM is complete. State another operator will perform the remaining steps.
STOP TIME:
7
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 2.
- The Reactor is in cold shutdown
- The Unit 2 Spent Fuel Pool water level is lowering.
- Fire Protection is available to assist INITIATING CUES:
The Unit Supervisor directs you to align EECW Makeup to Unit 2 Spent Fuel Pool per 2-AOI-78-1 Attachment 2 starting at step [3].
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
8
START UP AND SYNCHRONIZE UNIT 3 PREFERRED SITE: BFN JPM TITLE:
MMG SET JPM NUMBER: 307 REVISION: 6 TASK APPLICABILITY: SRO STA UO NAUO TASK NUMBER / TASK TITLE(S): S-57C-NO-04 K/A RATINGS: RO: 2.5 SRO: 2.9 262002 Uninterruptable Power Supply (A.C./D.C.) A1.02; Ability to predict and/or monitor changes in parameters associated with K/A No. &STATEMENT:
operating the UNINTERRUPTABLE POWER SUPPLY (A.C./D.C.) controls including: Motor generator outputs RELATED PRA INFORMATION: Risk Significant SAFETY FUNCTION: 6 EVALUATION LOCATION: In-Plant Simulator Control Room Lab Other - List APPLICABLE METHOD OF TESTING: Discussion Simulate/Walkthrough Perform TIME FOR COMPLETION: NA TIME CRITICAL (Y/N) N ALTERNATE PATH (Y/N) N Developed by:
Developer Date (Ensure validator is briefed on exam security per NPG-SPP-17.8.1)
(See JPM Validation Checklist in NPG-SPP-17.8.2)
Validated by:
Validator Date Approved by:
Site Training Management Date Approved by:
Site Training Program Owner Date 1
OPERATOR: ________________________________ JPM Number: _307___
TASK STANDARD: Perform operations necessary to Start-up and synchronize Unit Preferred MMG Set Operator Fundamental evaluated:
OF-1 Monitoring plant indications and conditions closely.
OF-2 Controlling plant Evolutions Precisely PRA: NA REFERENCES/PROCEDURES NEEDED: 0-OI-57C VALIDATIONTIME: 25 min PERFORMANCE TIME:
COMMENTS:
Additional comment sheets attached? YES ___ NO ___
RESULTS: SATISFACTORY ____ UNSATISFACTORY ____
IF UNSAT results are obtained THEN Retain entire JPM for records.(Otherwise just retain this page.)
SIGNATURE: ___________________________ DATE: __________
EXAMINER 2
Revision Summary Rev Effective Pages Description No. Date Affected 1 10/26/94 ALL GENERAL REVISION 2 05/07/95 ALL GENERAL REVISION FORMAT, PROCEDURE REVISION, ADDED 3 10/15/97 ALL PLANT WORK EXPECTATIONS TOUCH STAAR, SAFETY, AND 3-WAY COMM.
PROCEDURE REVISION, FORMAT 4 11/10/99 ALL DOCUMENT 5 10/03/01 ALL PROCEDURE REVISION 6 04/28/15 ALL UPDATE TO NEW FORMAT 3
IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is in cold shutdown
- The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1.
- Maintenance has been completed on the Unit 3 Unit Preferred MMG Set.
INITIATING CUES:
The SM directs you to start up and synchronize the Unit 3 Unit Preferred MMG Set as directed by 0-OI-57C per section 5.5 step 5.5[16].
NOTE: PERFORMER WILL NEED GGMKA KEY.
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
4
START TIME:
STEP / STANDARD SAT / UNSAT Step 1:
NOTE Steps 5.5[16] through 5.5[26] are performed from Battery Board Room 2 UNIT PFD Sync. & Speed Control Panel. Critical Step SAT
[16] PLACE UNIT 3 MMG OPERATING MODE, 3-HS-252-02AB in AUTO.
UNSAT Standard:
N/A VERIFIED/SIMULATED PLACING the Unit 3 MMG SET OPERATING MODE 3-HS-252-02AB in AUTO.
Cue: The Unit 3 MMG SET OPERATING MODE 3-HS-252-02AB is in AUTO position.
Step 2:
Critical Step
[17] PLACE UNIT 3 MMG LOCAL-REMOTE CONTROL, 3-XS-252-02A in REMOTE.
SAT Standard:
UNSAT SIMULATED PLACING the Unit 3 MMG SET LOCAL-REMOTE N/A CONTROL 3-XS-252-02A in the REMOTE position.
Cue: The Unit 3 MMG SET LOCAL-REMOTE CONTROL 3-HS-252-02A is in the REMOTE position.
Step 3:
[18] PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE Critical Step SYNC SWITCH SS-7, 3-HS-252-03/SS-7 in ON.
SAT Standard:
UNSAT SIMULATED PLACING UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 3-HS-252-03/SS-7, in the ON N/A position.
5
STEP / STANDARD SAT / UNSAT Cue: The Unit 3 PFD SYSTEM GENERATOR SOURCE SYNC SS-7, SWITCH 3-HS-252-003/SS-7 is in the ON position.
Step 4:
NOTE MMG voltage and hertz are read as INCOMING.
Critical Step
[19] MATCH Incoming to Running AC volts using UNIT 3 MMG VOLTAGE ADJUST, 3-HS-252-02CD. SAT Standard: UNSAT SIMULATED MANIPULATING UNIT 3 MMG VOLTAGE ADJUST, N/A 3-HS 252-02CD until cued that incoming and running AC volts are matched.
Cue: INCOMING and RUNNING VOLTAGES are EQUAL at 122 Volts Step 5:
[20] ADJUST MMG speed using UNIT 3 MMG FREQUENCY ADJUST, 3-HS-252-02CF to obtain a synchroscope slowly rotating in the SLOW Critical Step (counter-clockwise) direction (10 to 15 second rotation) as indicated on SYNCHROSCOPE, 0-SCP-252-000A/B.
SAT Standard:
UNSAT SIMULATED ADJUSTING UNIT 3 MMG FREQUENCY ADJUST N/A 3-HS-252-02CF speed control switch until cued that synchroscope indicator rotating in the counterclockwise direction at 10 to 15 seconds per revolution.
Cue: State: The Initial Synchroscope indicator is standing still at the 5 oclock position.
Note: If student raises frequency the state: Synchroscope indicator is rotating in the CLOCKWISE direction at 12 seconds per revolution.
Note: If student lowers frequency the state: Synchroscope indicator is rotating in the COUNTERCLOCKWISE direction at 12 seconds per revolution.
6
STEP / STANDARD SAT / UNSAT Step 6:
NOTES
- 1) Section 5.5[21] should be performed expeditiously (within about 15 seconds) to minimize the time AC Systems are paralleled to prevent tripping the MMG set. Voltage and amps is expected to fluctuate while the AC systems are paralleled and the MMG set will trip if the AC systems are paralleled for approximately 30 seconds.
- 2) If breaker 1001 trips, it must be reset with reset push button on the respective Unit Battery Board, Panel 10.
CAUTIONS
- 1) Voltage Oscillations may occur during Bus Power Transfers.
These oscillations are caused when two Power Supplies having separate Voltage Regulators try to maintain voltage control.
Therefore, the time the Power Supplies are paralleled should be minimized as follows:[PER 64835]
- When transferring Bus power supplies from one MMG to Critical Step another MMG.
- When transferring Bus power supplies from one MMG with the SAT unit preferred transformer. (Unit 2 has a Voltage Regulator Transformer which makes voltage oscillations more UNSAT susceptible.)
N/A
- 2) Minimize the number of Bus power supply transfers and only transfer Bus power supplies when absolutely necessary.
- 3) During the transfer of Bus power supplies the affiliated RPS circuit protectors 1(2)C1 and/or 1(2)C2 may trip.
Start of Critical Step(s)
[21] WHEN SYNCHROSCOPE, 0-SCP-252-000A/B is 5 minutes prior to 12 o'clock, in the SLOW counter-clockwise direction, THEN PERFORM the following expeditiously:
[21.1] CLOSE UNIT 3 BKR 1001, using 0-HS-280-003/1001.
[21.2] ENSURE CLOSED UNIT 3 BKR 1001.
7
STEP / STANDARD SAT / UNSAT Standard( step 6 continued):
When cued synchroscope indicator at 5 minutes prior to 12 o'clock, SIMULATED PLACING 3-BKR 1001, 0-HS-252-003/1001 in the CLOSE position.
NOTE: IT WOULD ASSIST THE EXAMINEE IF THE EVALUATOR WOULD USE HIS FINGER TO DEMONSTRATE INDICATOR POSITION ON THE SYNCHROSCOPE AS THE READINGS ARE ENUNCIATED.
CUE: THE SYNCHROSCOPE INDICATOR IS AT 30 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 15 MINUTES BEFORE THE 12 O'CLOCK POSITION. THE SYNCHROSCOPE INDICATOR IS AT 5 MINUTES BEFORE THE 12 O'CLOCK POSITION.
CUE: [WHEN CLOSED] UNIT 3 BREAKER 1001 BREAKER POSITION INDICATING LAMP CHANGED FROM ILLUMINATED GREEN TO ILLUMINATED RED.
Step 7:
[21.3] OPEN the UNIT 3)BKR 1002, using 0-HS-280-003/1002. Critical Step End of Critical Step(s) SAT Standard: UNSAT SIMULATED UNIT 3 BKR 1002, 0-HS-282-003/1002in the OPEN N/A position.
CUE: UNIT 3 BKR 1002, 0-HS-282-003/1002 IS IN THE OPEN POSITION WITH RED LIGHT ILLUMINATED.
NOTE: DO NOT ALLOW THE EXAMINEE TO OPERATE THE AMMETER SELECTOR SWITCH FOR THE FOLLOWING STEP.
Step 8:
[22] CHECK generator is loaded by observing UNIT 3 MMG GENERATOR amps, 3-II-252-02C/1AMR L2 rise, "N" should be UNSAT approximately the difference of L1& L2 (UNIT 3 MMG GENERATOR amps, 3-HS-252-02CH positions 1, 2, & 3 are respective to L1, L2 & N).
N/A 8
STEP / STANDARD SAT / UNSAT Standard:
CHECKED amp indicators L1 MINUS L2 approximately equals n.
Cue: L1, L2, N AMPS INDICATIONS HAVE RISEN and L1-L2 = N.
Note: Selector Switch positions are labeled as follows: Position 1 is L1, position 2 is L2 and Position 3 is N.
Step 9:
[23] ENSURE OPEN UNIT 3 BKR 1003, 0-HS-280-003/1003 SAT Standard: UNSAT VERIFIED ILLUMINATED GREEN position indicating light above 0- N/A HS-282-003/1003.
Cue: Unit 3 Breaker 1003 0-HS-280-003/1003 Position Indicating Lamp changed from illuminated RED to illuminated GREEN.
Step 10:
[24] On Unit 2 Unit Preferred MMG Set Local Control Panel, ENSURE OPEN the following fused disconnect switches:
- BACKUP SOURCE TO BAT BD 1 BKR 1003, 1-FUDS-280-001/1003 SAT
- BACKUP SOURCE TO BAT BD 3 BKR 1003, 3-FUDS-280-UNSAT 003/1003 N/A Standard:
At Unit 2 Unit Preferred MMG Set Local Control Panel VERIFIED 1-FUDS-280-001/1003 AND 3-FUDS-280-003/1003 in the OPEN POSITION.
Cue: 1-FUDS-280-001/1003 and 3-FUDS-280-003/1003 are in the OPEN position.
9
STEP / STANDARD SAT / UNSAT Step 11:
[25] On Unit 3 Unit Preferred MMG Set Local Control Panel, ENSURE the BACKUP SOURCE TO BAT BD 2 BKR 1003, SAT 2-FUDS-280-002/1003 fused disconnect switch is open:
UNSAT Standard:
N/A On Unit 3 Unit Preferred MMG Set Local Control Panel, VERIFIED 2-FUDS-280-002/1003 in the OPEN position.
Cue: 2-FUDS-280-002/1003 is in the OPEN position.
Step 12:
[26] On Battery Board 2:
PLACE UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH SAT SS-7, 1-HS-252-03/SS-7 in OFF.
UNSAT Standard:
N/A SIMULATED PLACING UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 1-HS-252-03/SS-7 in the OFF position.
Cue: UNIT 3 PFD SYSTEM GENERATOR SOURCE SYNC SWITCH, SS-7, 1-HS-252-03/SS-7 is in the OFF position.
Step 13:
[27] On Battery Board 2:
Critical Step DEPRESS UNIT 3 MMG AC MOTOR START, 3-HS-252-02AD to return SAT to Normal AC power from DC drive.
UNSAT Standard:
N/A SIMULATED DEPRESSING and RELEASING UNIT 3 MMG AC MOTOR START , 3-HS-252-02AD pushbutton.
Cue: [The AC motor Breaker Position Indicating Lamp changed from illuminated GREEN to illuminated RED. State Another Operator will continue with procedure and this will end the task.
STOP TIME:
10
Provide to Applicant IN-PLANT: I will explain the initial conditions and state the task to be performed. ALL STEPS WILL BE SIMULATED. Do NOT operate any plant equipment. Touch STAAR may be carried out to the point of touching a label. If it becomes necessary to physically touch a control switch, use a non-conductive pointing device. I will provide initiating cues and indicate any steps to be discussed. When you complete the task successfully, the objective for this job performance measure will be satisfied. When your task is given, you will repeat the task and I will acknowledge "That's correct" (or That's incorrect", if applicable). When you have completed your assigned task, you will say, "My task is complete" and I will acknowledge that your task is complete.
INITIAL CONDITIONS:
You are an Operator on Unit 3.
- The Reactor is in cold shutdown
- The Unit 3 Unit Preferred Bus is being supplied from the Unit 3 Unit Preferred Transformer in accordance with Section 8.1.
- Maintenance has been completed on the Unit 3 Unit Preferred MMG Set.
INITIATING CUES:
The SM directs you to start up and synchronize the Unit 3 Unit Preferred MMG Set as directed by 0-OI-57C per section 5.5 step 5.5[16].
NOTE: PERFORMER WILL NEED GGMKA KEY.
CAUTION: DO NOT OPERATE ANY PLANT EQUIPMENT!
11