ML023040338

Part 2 of 4 - Course Outline for R-304-B and BWR Systems Lesson Plans

ML023040338
Person / Time
Site:	Browns Ferry
Issue date:	09/19/2002
From:	- No Known Affiliation
To:	Office of Nuclear Reactor Regulation
References
FOIA/PA-2002-0343
Download: ML023040338 (147)

Text

Revision Date BWR SYSTE, S LESSON PLAN A. RECIRCULATION SYSTEM B. REFERErNCES

1. BWR Systems 'Manual, Chapters 2.5 and 3.2

2. Recirculation System GEK'779, VoJ. II

3. Brown's Ferry Technical Specificatons5

4. Reference Card File 2.5

5. Operating Instructions C. OBJECTIVES Fullv understand the purpose of the system and its design basis

2. ;ajor system components and flow paths

3. Sicnificant system instrumentation and interlocks

. Relationships between the RecirculaT-ion System and other systems

. Technical Scecifications governing tne syste-i FurE D.St"cn

e. -rzvidss vari"-ie forced circulation of water zhrough the

-cors; azle -o ahi:heve hicher s.Ecific znereby Do;..:r and control flow niszribizicn to all cnanneis. Sy

,:Er,,in zne flow rate. different power densitieS can be acrieved and power level chanoed.

2. Coo.nents 8 Flow Path

-'c:*r opei'-=aec SC suc'. on

• -2

2) 'iariable speed pump

3) 'Iotor operated pump discharge valve

4) Jet pump ring header

5) Each loop supplies 10 jet pumps

6) Crosstie and crosstie bypass valves

7) Recirc System MG Set.

b.- Flow Paths (Fig. 2)

1) Recirc pump suction from reactor vessel downcomer region between groups of jet pumps

2) Two separate loops

3) Discharge of recirc pump passes through a flow element and is routed to a ring header (not a complete ring)

4) Flow from each recirc pump goes from ring header to reactor vessel via 5 riser pipes

5) internal to the reactor vessel each riser feeds two jet pump nozzles via a ram's head arrangement E) in the jet pumps the driving flow (from the recirc pumps) mixes with the driven or secondary flow from the vessel down corner region (j'ryer and separator drains olus feed flow) andr returns, via the jet pump diffuser zo -ne core inlet

- 1e n um.

7) The total recirculation system flow passes tnrough the core a, 90'. of fiow through fuel channels shis 10*: of flow by~asses fue' cue to desicred leakace.

flow prevents excessive voiding in the area of the LPRMI's and increases their accuracy.

l 0".: core `Io,, 102 .5 x 1lc. Ib/hr a; ' x 10 lb/hr is drivin- flow

-3 b) -.62 x 106 lb/hr is driven flow c) -,13.4 x 106 lb/hr of the above is taken as steam f.ow; this beino made up by feedvwater flow.

Recirculation ratio is 8/1 E. COMPONIET DESCRIPTION (Fig. 2)

1. Recirculation Loop Outlet

a. -.28" recirculation loop suction piping

2. Pump Suction Valve

a. 28" Gate Valve

b. Designed to open against a 50.psi differential. (Equivalent to the static head of water in the reactor vessel.)

3. Pump Discharge Valve

a. 28" Gate Valve

b. Designed to open against a 200 psi differential. (Equivalent to-about shutoff head of the recirculation pump.)

c. Originally this plant had a 4" bypass valve around the pump discharge valve. However, due to cracking problems found at various BWR facilities in the discharge valve bypass line many facilities including BFNP removed the bypass line and modified the recirculation pump starting sequence.

". .. er......,aicn Pumo and Motor

a. 2000 HP variable speed induction motor (4 pole, 345-1725 RPM at 11.5 to 57.5 HZ Supply frequency

b. Possible soeed range

1) Minimum Speed: 3A5 RPM - 11.5 HZ - 20%

2) M1aximum Speed: 1725 RPM - 57.5 HZ - 100'

3) Minimum Speedw: 483 RP-I - 16.1HZ - 28%

• ..s limited by sneed controller

• -4

c. Dump Flow Rating (design conditions **)

1) 12,650 GPM at 28U speed

2) 45,230 GPM at i10% speed

"* The Generator and Pump Motor are not designed to pump 100' rated flow when pumping cold water.

If attempt is made to do so a limiting condition of generator stator amps will be reached prior to attain ing 1000 speed.

d. Pump Motor Limits

1) Rated Voltage: 3920 VAC at 70V/HZ

2) Rated Current: 965 Amps

3) Maximum winding temperature 216°F

e. Restart Capabilities

1) Two consecutive starts allowed from motor ambient temperature

2) One start allowed from motor operating temperature

NOTE: Further starts require an intervening cooling period of 15 minutes.

f. Cooling Water Requirements

1) Suppiec by RESCAI

, M.ozor oiI cooer  !.S GP?

3, Pump seal assembly 47 GPM G. Ps': Seal Assembly (Fig. 3, 4 & 5) sealing i' Sea- car:ridge assembly consisTs of two sets of surfaces and breakdown bushing assemblies The =1 sea!

T b) The =2 seal

"-rs, nc,-- ,

ceratrnc rc--ionS eacn sel :-c,..zes

:,:: SI : :n:Bcros s Ur-ace

d) These sealing surfaces form two cavities from which the above oressures are measured.

(1) No. 1 cavity at reactor pressure (1000 psig @

rated)

(2) No. 2 cavity at 50. reactor pressure (500 psig

@ rated)

NOTE: Flow is controlled internally through the seal assembly so that these pressures are maintained.

2) Seal Purging a) Seal purge water from control rod drive system down stream of the supply filters keeps number one seal cavity clean by flowing out of the seal area, along the pump shaft, and into the recirculation system.

b) A flow of 2 1/2 to 3 GPII goes to each pump through a restricting orifice, flow regulator, and rotameter c) The ource reduces the possibility of seal damage due to ingesting dirt from an unclean piping system

3) Seal Flow a) During normal operation of the seal some flow through the seal assembly is reouired to allow each seal to accept i/2 of the oressure droD (normally 500= each).

(1) ' ormal flow set at .77 GP?"

(2) Passes through internal breakdown bushings to controlled seal leakoff line from =2 seal cavizV (2) All seal leakage routed to Dryweeli equi:menrz crair sunp.

") Seal Failure a- Failure of the =1 seal asserbly woulo allow increased flow to the `2 seal cavity, forcing the -2 seal to operate at a higher _"Pi.e.: >500 PSID.

-6 Failure of the *I seal will cause increased leakage

-1I.1 GPM through the controlled seal leakoff line (1) Alarms high at .9 GPM (2) Alarms low at .25 GPM b) Failure of the #2 seal would cause an increased leakage through the seal leak detection line downstream from the #2 seal (1) This condition alarms at .25 GPM. Normally there is zero flow c) Failure of both mechanical seals would result in a total leakage from the seal assembly of 60 GPM (maximum)

(1) The breakdown bushings limit the above total leakage d) Plugging the #1 R.O. would result in a reduction in *2 seal pressure and FS "A" alarming low e) Plugging the =2 R.O. would result in *2 seal pressure and FS "A" alarming low.

• ) Seal Cooling (Fig. 6) a) Due to the heat generated by the friction of tne" sealing surfaces and the leakage of reactor water through the seal assenbly, cooling is recuired.

b Cooilnc suo-lied by - CC, . systee '-7 G?' recuirs' c) Heat exchanger provided which surrounds the seal assembly d) Primary water is routed via:

(1) Hole in main pumm i~meller (2) Hydrostatic bearing (3) Post shaft-to-casing clearance

)rimEry

.. water circ:.ae* :nrouch heat exc-"an=r

.u~e s-ce to seal a:iC.':

(1) Auxiliary impeller mounted on main pump shaft just beWow the seal assemblies f) If RBCC, is lost to the pDuo and motor, the pumo should be tripped in -. l minute to prevent bearing and/or seal damage

5. Recirculation System ""- Sets (Fig. 7)

a. The recirculation pumps are driven by MG Sets, located in the turbine building on the turbine floor. The MG Set drive motor and generator are connected by a fluid coupler which controls the speed of the genirator and thus the pump motor.

b. Drive M6tor

1) 9000 HP - 6 pole - 1200 RPM Induction Motor

2) Maximum Current - 1125 Amps at 60.0 HZ (Gen. @ 57.5 HZ)

3) Rated voltage - 4160V AC

4) Maximum Winding Temperature - 2480F

c. Generator

1) Variable Frequency Generator (6 pole, 224-1150 RPM

@ 11.5 to 57.5 HZ)

2) Power Rating - 5985 KW at 56 HZ

3) Power Factor - 0.9 @ 50 HZ

": .ated Volit-:e - 3920'V AC z EZ V ,C at 57."

5C23

3) ,aximum Current 979 Amps E) ".aximum Wirdinc Te.-mperature 260 F

d. ,oltace Regulator and Excitation normal Ooeration N) a) The generator is excited by an AC exciter whose output is converted to DC via rotor mounted diodes and applied z-. :he -"ield via s!i: rincs. The exciter is dr.iven by the zn *'.. .- mr:,ozor "7ý Tnital :Start-,

-) Excitazion -s supplied Fro: the IZCV A-C. 60 K"

-ssential service bus.

3) Transfer to self excitation is time delayed following closure of the generator field breaker "f) The voltage regulation is supplied by a volts/HZ type regulator-which decreases the output voltage by 70V/,,Z as as the frequency is decreased.

5) Decreasing the frequency of the applied voltage on an AC induction motor lowers the power factor. Maintaining a constant voltage would require excessive amounts of excitation current which could cause overheating of the.

exciter and/or voltage regulator.

6) Thus the need to program the output voltage down with decreasing frequency.

7) The output of the generator is hard wired directly to the recirc pump motor.

a) The inertia of the rotating elements in the generator supplements the inertia of the recirc pump and motor to provide a coastdown of action or flywheel effect upon loss of station power.

b) The full flywheel effect depends on two factors 1I) Adequate generator excitation (2) Dependable fluid drive scoop tube control c) At least 10 seconds coastdown time is provided on a trip from EO*= speed or greater.

(*) Tie -rratns r'oirc flow Bcaszcown helps protect the fuel from excessive temoeratures following a loss of power

e. Fijid Czupler (Fir. )

i) Ooera~icn a) Four basic elements make up the fluid drive unit.

(1) Inpu: (driving) shaft (2) Output (driven) shaft I-%

, means of varying flIid level

b) The input shaft, impeller, impeller, imoeller casing, inner casing ana outer casing all rotate together at drive motor speed c) The runner and output snaft rotate togetner at a speed governed by the quantity of oil in the vortex and the load conditions d) The input and output rotating assemblies are supported on their respective sleeve bearings mounted in pillow blocks e) Hydraulic thrust is absorbed by Kingsbury thrust bearings included in above pillow blocks f) There is no mechanical connection between the input and output members g) Steady state operation (1) The impeller, which is directly connected to the prime mover, imparts its energy to the oil (2) The oil, flowing in its vortex (whirlpool) pattern, transmits its energy to the runner to drive the load (3) When the.working circuit of the iZzeller and runner is filled with oil, the drive is capatle of trans mitting maximum power with the least slip or differential speea between the impeller and runner P2 Ry introducing a movatie scoop zube into the casings, the amount of oii in the casings can be adfusted from Oull to ernty (0) Reaction to adjusqmenz is fast and smooth over a wide speed range.

h) Transien: operation (i) Oil enters the working oil circuit thrcugh ports in the inboard end of the impeller pillow clock (2) There is always a fixed quantity of oil entering the working circuit due to positive displacement oil pumps and orificing Mhe all is ac:eo Aon ty :hE ;TEeand :ent,-i "fucal force, 'orring a vcr:ex :atzern anc transmitting its force to tne runner

(4) The speed control scoop tube position controls the quantity of oil in the working circbit (5) The momentum of the rotating oil forces some of the oil out of the stationary scoop tube and into the oil reservoir. (Fig. 9)

(6) Insertion of the scoop tube into the vortex removes oil faster than it is being supplied, reducing the quantity of oil in the working circuit (7) This reduction of oil results in less coupling and a lower generator speed (8) If the scoop tube is now stopped, the rate of removal will equalize with the rate of supply and the quantity of oil in the working circuit stabilizes at some new, lesser amount (9) With scoop tube fully inserted --min. couoling With scoop tube fully retracted- max. coupling

2) Oil Supply System (Fig. i0) al in addition to the wcrkin; circuit, the oil su::iy system must provide:

(1) Cooling (2) Lubricating b) Three hal" caoacity, :csitive displacement 60 HP AC oil pumps rated at 5IA GPM and one KIM DC emergency oil pymp rated at 156 7M take suction from tie fluid coupler reservcir.

c) A relief valve at the discharge of the pump controls the discharge pressure by relieving back to the suction of the pump (0) This maintains a constanz pumpIna rate and allows a fixed quantity of oil to enter the working circuit d) The oil travels to an oil cooler. The cooled oil is returned to the fluid drive where a portion is passed through filters for lubrication of fluid drive motor and generator bearings e) If one of the oil pumps fails, the following sequence

-occurs:

(1) Time 0 - oil pressure drops to <30 psig (a) The standby A/C oil pumps auto starts (2) Time + 6 secs. - if oil pressure still 30 psig, (a) auto. trips AC oil pumps (if DC pump lined up to start)

(b) auto. trips of MIG drive motor

(.3) If pressure drops to 20' psig (or redundant 10 psig), the DC oil pump auto. starts (after 6 sec T.D.)

(a) The D. C. pump wr i provide fluid coupler bearing oil :ressure only for coastdown purposes fol*i"nc loss of the AC curs e~ps

7. Jet

a. FGn-tion

- ro,.vie maximum core flow with rinirmum external flow 2" Provide 2/3 core height "standpice" effect follo"ing a design break accident (Fig. il) a) Steam formed in the lower 2/3 of the core will flow upward, cooling the top portion of the core

-:;W n R-P xnr irn1 -rnal 7Arscon plan for c*Ea-l zT

b. Like centrifugal pumps, a jet pump converts velocity head into a pressure head. (Fig. 12)

1) Due to the convergent section of the driving flow nozzle, the driving flow is accelerated to a high velocity.

2) This in turn creates a low pressure in the throat area. Due to this pressure differential, the driven flow is accelerated and entrained with the driving flow stream

3) In the diffuser section, a further reduction in velocity

-is achieved and the resultant discharge pressure is developed

c. The performance of jet pumps is generally shown to be a function of the parameters defined below.

EOZZLE TH ,OAT C: LFUSE.

118 2 :J, ST ;!(PI -PC "CTI N F--C "

q .J7I -'

LCJ' 11 clw R,atio. M=the ratio of the driven mass flow (suct.cn flo;:) to the driving mass Io, through the nozzle Driven  : W1 1 6S x 10 --/Hr. 2 Driving 3A x 106 -/Hr 1

• - :u- -eace* (F'ic. 2j

a. Each recircuiation loe0 _-',:Scn1rge line terminazes in a 22" manifold or "ring he-acer" wnich encompasses the reactor vessel

b. Flow from each recirc pump is routed from the manifold to 5 - l2" jet punp risers. Each riser supplies driving flow to 2 jet pumps

c. The -ring header" is split by two valves

1) Installed to allow operation of all 20 jet pumps from one recirc pump a) Designed to minimize flux tilting which may result from single loop operation

2) Startup test results indicate operating pump may go into runout when the crosstie valves are opened due to doubling the flow area a) This reduces the pump discharge pressure which supplies the hydraulic force to the hydrostatic bearing (1) Internal pump damage may be the end result b) Therefore, operating procedures prevent openinc tho crosstie valves and only allow one crosstie bypass valve to be open to prevent overpressure N0TE: The- flux tilt was found to be minor in nature (3- )

d. The crosstie valves each have an equalizer valve

'.' They prevent a pressure buildup between the t.o crosstie valves

2) Pressure in a solid system will increase -ClO= per CF increase

..... Set Venrtiaticn System

a. -wo l00-. capacity ventilation axial fans supply cooling air to both !MG set drive motors and generators

b. There are no interlocks to prevent star:ing the MG set crive motor without vent fans. However, procedures require that at least one fan be operating whenever an MG set is running

.. * . :.. r , a' r-In*een,

.=-E -.o :.et'en'

e- -r ~Se-3 c*

o---- ... on- .Tof..--r ur e i -. . - -

F. I NSTRUME..TATI ON

1. Control Room

a. 902-4 panel Instrument iyoe Ranae 600OF 3 Recirc loop temperatures Recorder 00 70 x 1O3 GPM Indicators Recirc pump loop flows Recorder 0 70 x 1O GPM Indicators 0 80 x l1 =/hr Loop flows 0 8 xO10 #/hr Jet pumps 1,6,11,16 flows Indicators Multipoint 0 600 F Recirc pump & MG set temp. Recorder Multipoint 0 - 300 0 F Recirc drive motor & generator Recorder Status temps. 0 - 300 psid Recirc pump differential Indicator pressure Recirc pump power

1) generator current Indicator 0 1500 Amps Indicator 0 8000 KW

2) generator power 0 5.25 KV

3) generator voltage Indicator Indicator 0 1500 Amps Recirc 11G drive motor current Indicator Pump seal pressures

1) =1 Indicator 0 - 1500=

Indicator 0 - i500=

2) =2 Indicator 0 - 30 psid Jet pump flows (individual) Indicator 100 - 2500 rpm Recirc pump motor speed 20-100,:

Recirc !l set generator soeed Indicator instrument iyv~t Rance Rcorder 0 120 -sid Total ccre floi! 0 - EO Recorder Core oressure drop

c. 902-21 fiack panel Rance instrument 0 - 600°F Vessel bottom head Multipoint Recorder Drain temc.

2. Local

a. Reactor buildino Instrument Type Range Recirc pump seal pressures gages 0 - 1500 =:

3. Significant Interlocks, Trips and Alarms Item Set Point Functi on Recirc pump low AP >4 psid Allows start signal to be applied to 11/G set

>20%V Provides adequate Feedwater flow interlock sub cooling for recirc pump speeds up to l'IMY.

Recirc pump speed cannot be increased above minimum until interlock is cleared.

Cavitation may damage impeller Any feed pump Recirculation pump Recirc oump runback/speed liniter speed is runback

<20S rated flow and or limited to 75%:

vessel level so that the feed

>low levei water ccntrol svszem alarm '+27")

maintain or recover reactor water level upon loss of a reactor feed pump.

ec'rc discharge valve not Valve <90% Prevenzs increasing open recirc pump speed full open interlock above minimum unless valve is open.

Possible pump internal damace.

_- ... e - .o e~s  :,ur:.

noz starz or will trip if runninc.

Set Point Function Recirc pump trip -51.5" reactor Low water level water level NPSH for recirc pumps. Possible cavitation problems M/G oil pump auto start <30 psig Allows time for w/l sec. T.D. running oil pump to restore pressure. At the end of 1 sec., auto starts standby.

oil pump

<30 psig & After 6 secs., if 6 sec. T.D. oil pressure is still <30=, trips the recirc M/G set, and AC oil pumps (if DC pump lined up to start)

<20= or <10# Starts DC oil pump 6 sec. T.D.

v" M.! Detect seal failure Contro! seal low flow

--zrol -eal hi4C fIow Detect seal failure

.25 GPM Detect seal failure

=2 seal leak

. PST- 7 R#-!OAL

SUMMARY

. or-aI O:eration

a. -*m-umSpeed Operation 1, The limiting minimum recirculation pump speed has been established so that, with only one pump running, a su* icient flow will be produced zo minimize reactor vessel

a) Potentially high differential temperature can exist in the vessel bottom head Eeaion due to the CRD cooling water, injected at 70 - 90 F b) It is desired to keep the LT between the saturation temperature and the water from the vessel b8 ttom head drain drain to the cleanup system at a value <15 F and the between an igle and an operating recirculation loop at a value <50 F

2) To accomplish the above:

a) The minimum recirc pump speed is procedurally limited to 28' even though the fluid coupler could operate down to 20' b) The vessel bottom drain line was connected to the cleanup system for accurate temperature indication in the bottom head region.

(1) Drain valve has a drilled disc to allow flow at all times and prevent stagnation

3) A 'T between saturation temperature and the bottom head

-temperature is not limiting in itself. The stresses occur when starting an idle pump or increasing flow. Hot water now sPjeeps out the cold, producing an unconzrolled heatup.

a) Regions of primary concern are:

(1) CR% housing to stub tube welds (2) RV:-!zo RPV skirt welds b) in additicn, the cold water is swept up and through the core, producing a reactivity transient

b. "ax'mum Soeed ODeration

1) The recirculation pumrs are sized ard desi-cned for pu.ring reactor water at rated condizic-'ns, i.e.:

2) Rated core mass flow 102.5 x 106 lb/hr, can be achieved

• >G -*temperatures.

ar lower *.. However,

- .,: wil on curren: ' limits *

" - -rive to -cr and/cr.,r

"- en ..zr r.

aenro'¶r e:  ::c:

wa-E-r

3) By design the recirculation system is rated at 56.0 HZ.

However. zhe liriting speed is 57.5 HZ with the generator the limiting component

4) 100% core flow is normally achieved at approximately 90:

pump speed

c. Pump NPSH Requirements

1) NPSH is defined as a measure of the difference between the statij*vressure and the saturation pressure at the pump inlet

2) The static pressure is comprised of two effects (a) The height of the column of water above the pump (b) The amount- of subcooling at the eye of the pump

3) The recirc pumps are located approximately 60 feet below normal reactor operating level. This provides adequate IPSH-uring low power saturated operation

4) Feedwater flow provides the subcooling to the recirc pump suction when operating at higher power levels,-20F

@ 100': power condition

5) An interlock prevents increasing recirc pump speed above the minimum value (28%) unless at least 20% F.W. flow is present for subcooiing At full -ower, fes:

d. Single Loop Operaticn 2 Single loop oDeraticn is allowed, but the operator mus: ensure that the recirc loop flow for the loop wizrn the running pumo *iO% by reducing operating pump soeed

2) Additi"on:- lly, the ooerator rust ensure that opera:rin; pump Anos, motor winding temperature, bearing :empera:ures.

are all wi:nin allowable limits and motor vibration

3) When a running :ump trios. the discharge valve for that

) Aizws :ne :ure :0 ccme to rest.

riozec er S

-inutes oper h'e disCsarce valve as necessary t:

¶aint:ain loco zemperature

e. Starting an idle pump loop 0

1) If the pumD has been isolated and >50 F below reactor tenperature, open the suction valve, establish seal water supply, and throttle the discharge valve sufficiently to establish a heat up rate :100 F/hr

2) When the idle loop temperature is within 500F of reactor temperatur 8 and when vessel bottom head temperature'is within 145 F of reactor (saturation) temperature, shut the idle pump discharge valve

% 0

3) Establish fluid drive oil temperature !9O F with cooling water established to oil coolers

4) Ensure the operating pump *50% speed

5) Start the idle pump at minimum speed NOTES: (1) Do not start an idle recirc pump when APRrI's are at the rod block. Insert control rods as required to provide 5-8% power margin between APRM power and APRM rod block (2) The 50-: AT limit between the idle loop temperature and reactor temperature orevents a large uncontrolled thermal stress on the pump casing. Small internal components heat up and expand faster than the casing and pump drainage might otherwise occur.

Additionally it limits the cold water reactivity addition effect (3)The lL°F 4T lirii  :-. vessel botzcm nead temperature and reactor temoerature is based on limitino thermal stress on CRD housing to stub tube welds and -hermal stress on reactor vessel to suDDort skirt welds. if tne ILC ,T limit is exceeded, :he reac:or sa..ration teroerature must be lowered to reduce the CT.

(*) Restart limitations must be observed.

(5) Once :he .jusz szarted pump A v increases >5 psid, its discharge valve will start to open by an automatic jogging circuit xiu which will get tne valve o~enwihn*senc

2. Abnormal operation

a. Operation with pumps at different speeds (Fig. 13)

1) Operating instructions limit pump speed mismatch during normal operat.ions as follows:

Power Level Speed Mismatch

<80 <35%

>80%, <22%

a) Large mismatches could cause flow-induced vibration of the lower speed jet pump risers (Region I of figure 13)

(1) The vibration results from turbulence generated by the sheer forces between the driving flow stream and the reversed secondary flo%! (Fig. 14).

Excessive vibrazion could cause faticue failure of the jet pump riser braces.

2) Region 2 of Fig. 13 is prohibited because of instability in fluid coupler

3) Region 3 of Fig. i3 is a transient region. Operation is allowed during pump restart only

b. Recirculation pump seal failure Sf only one seal fails, operation of the vump con-i,-,ue unt-"l. a pianned shutdo';r.

2 If the other seal leakage becomes excessive, shut the ou-.p down and isolate it

3) Check dryweli atmosphere conditions and leakage raze to ver7- pump isoia:ion

c. "solated loop

""ihen changing temperature in an isolated loop, the; ccoldown rate (or heatup rate) should be controlled to .30 F/hr.

This is a primary system limitation. The most limiting

/ - is -,he rscr. z c:--._:nc n in :h4-

d. Shutdown cooling mode of RHR

1) BFNP operating instructions call for securing the recirculation pump prior to starting RHR pumps to intiate shutodcvn cooling on that loop

2) There will be thermal stresses on the RHR line which ties into the recirculation pump discharge line and on the inlet riser nozzle penetrations to the jet pumps NOTE: See Dresden Lesson Plan on Recirculation System for a discussion of the condition where recirculation pumps are left running while shutdown cooling is in effect.

H. RELATIONSHIPS WITH OTHER SYSTEMS (Fig. 2)

1. Recirc loop "A" provides a suction path and both loops provide a discharge path for the residual heat removal system

2. Recirc loops A & B flow elements serve as inputs to the APRM and RBE flo.: biased circuits 3... RS.W cools recirculation pump seals and recirculation pump motor oil L. CRD hydraulic system provides seal purging water to the number one seal cavity

5. The reactor water cleanup system takes suction from the RHR suc:ion Dioe emanatinc in the "A' reirculation looo 3

""-c,-. he....

7n= :r-rv ssvsrv c-an be sarmied frc he ' retir ,-:

EcHUC~LSPECIFICATI O01,S I JeC. .z:~s

a. When.ever the-e is recirculation flcw .irh the reaczor ir.

-.ne sr or run nodes wiztoth recirculatior. pu':s r;nnlnc, *uo coerabilizv shall Le checked dail. by pu:

veri'vina that the following two conditions do not occur S imultarneously:

.'hen the two recirculation looos have a flow imbalance

-=-"" r -e-': * :r -sr*

2) The indicated value of core flow rate varies from the value derived from loop flow measurements by more than IOi 3 The difuser to lower plenum di-iferential pressure readino on an individual jet pump varies from the mean of all jet pump differential pressures by more than 10%

b. Additionally, when ooerating with one recirculation pump with th6e equalizer valves closed, the diffuser to lower plenum differential pressure shall be checked daily, and

"-the differential pressure of an individual jet pump in a Iooo shall not vary from the mean of all jet pump differential pressures in that loop by more than 10%

c. The operator would check 1) above by comparing recirc pump speed vs. recirc pump flow. For example, 90% pump speed normally corresponds to 100% flow in each pump. If one pump indicated 130% flow, it could indicate a possible failed jet pump in that loop

d. Since the core the.mal power-core flow relationship has been determined very accurately, the operator can derive core flow by finding the thermal power and, using the power to flow map, find the expected core flow. Comparing this value to the total core flow allows him to check 2) above

e. Both 1) and 3) or 2) and 3) occurring simultaneously is indicative of a failed jet pump riser or nozzle

f. Concern for jet pump operability is not for total vessel flow but rather for ECCS considera-ions

' Riser f-zilure ..,oid e-:CsE a larcer imaximum flo,. area for tne rmaximum credible accident 2: Low pressure ECCS systeins would of necessity have to be of larger capacity to acco.-cdate the increased blowdown rate and consequent more rapic uncovering of tne core

._. Rec.rca!;tion Pump Flow .,ismatch

a. '...enever Doth recirculazion pumms are in steady state operation,

. speeds shall be maintained within 22!: of each other when power level is greater than EC0 and within 35c.'; of each other

...,hen power level is less than 8C:.

b. :f mismatch limit cannot be met, one recirculation pump shall be tripped

c. Tne reactor shall not be operated with one recirculation loop out of service for more than 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />

d. Following one pump operation, the discharge valve of the idle pump may not be opened unless the operating pump speed <50%

NIOTE: Although the technical specification for flow mismatch was was originally provided for LPCI loop selection criteria, it still applies for jet pump vibration criteria criteria

3. Temperature limitations

a. The pump in an idle recirc loop shall not be started unless the temperatures of the coolnt within the idle loop and operating loop are within 50 8 F of each other.

b. The recirc pumps shall not be started unless coolant saturation temperature and vessel bottom head drain temperature are within 145°F.

Revi s ion Date _____________

BWR SYSTEMS LESSON PLAN A. MAIN STEAM SYSTEM B. REFERENCES

1. BWR Systems Manual Chapter 2.6

2. Brown's Ferry Nuclear Plant. FSAR Section 4.4, 4.5, 4.6, 4.11

3. Brown's Ferry Nuclear Plant Technical Specifications

4. Flow Diagrams 47W801-1 Mechanical Control Diagramr 47W610-1 Mechanical Logic Diagram 4714611-1

5. Reference Card File 2.6 C. OBJECTIVES

1. Fullyunderstand the purpose of the system and its design basis

2. ilajor system components and flow paths

3. Significant system instrumentation and interlocks Relationships between 'lain Steam System and other systems

". Technical Soecificazions ccvernig -he system

.GENERL DESCRIPTIOfI

i. Desicn Sasis

a. To cordoct steam :rz,' the r*e:.tr vessel ',hrcu*nl :he crn-ainmenz to the turbine - cenerazor.

b. To prevent uncontrolled release of prirary steam to t6e environs.

c. To assist in limiting pressure in the nuclear steam ceneration sys-em.

e. To provide Steam to HPCI and RCiC

2. Components (Figure 1)

a. Steam lines

b. Safety valves

c. Safety/relief valve

d. Flow restrictor

e. M1ain steam isolation valves (MSIV's)

f. Main steam line, HPCI steam line, and RCIC steam line drains and drain valves

g. Pressure equalizing header

h. Bypass valves (covered in Turbine Lesson Plan)

i. Turbine stop valves (covered in Turbine Lesson plan)

j. Turbine control valves (covered in Turbine Lesson Plan)

3. Flow Paths

a. Main Steam lines

1) 4 lines

2) Rates steam flow is 3.34 x 106 ./hr./line

b. Reactor head vent

c. Safety valves

d. Safety/Relief Valves

e. zTeam line :z H:C! turbine

f. S:ea line :o R1C^ zurbine

a. Szeam line drains l) Above seat

2) Selcw seat

h. HPCI and RCIC drains

i. Pressure equalizing header

.Steam to turbine

k. Bypass steam to condenser

1. Balance of plant steam requirements

1) Off-Gas system (RECHAR) a) SJAE Supply.(Ist and 2nd Stage b) SJAE Supply (3rd Stage) c) Off-gas pre-heater

2) Turbine driven reactor feedwater pumps

3) Gland sealing steam E. CflIPONENT DESCRIPTION

1. Steam Lines

a. Design Basis

1) To conduct steam from the reactor vessel through the primary containment to the steam turbine

2) To accommodate operational stresses, such as in ternal pressures. without a failure which could lead to a release of radioactivity in excess of the- cuideline values in 10 CFR 100.

3) The main steam lines within the D-4*av.. containment are t' witnszand zhe effects o an earthcuake with out a failure which could lead to a release of radioaczivizy in excess of the guideline values in 10 CFR 100.

a) P:rtions of the m.in steam lines are desicnazed Seismic Category +/- an- should be cesicned :o ;'2th szand zhe effects of tne safe shuzdown Earthquake (SSE).

a) From the outermost conzainment isolation valve up to but not including, the turbine stop valves b) Inter-connected Diping 2-1/2 inches or larger c : av

o arnd j~1/2 r- ,= ~ -- ~s

=-:tner nor-.=- , f ht '

_aZic closure .urin*.C ces of nA ,,S reactor ooeration.

b. Four 26" carbon steel steam lines used to:

1) Permit turbine stop valve and main steam isolation vai,,e -estino during ol ant operation wit, n-*.i.,

amount of load reouction.

2) Limit differential pressure on reactor internals under assumed accident conditions including a reptured steam line

3) Limit inventory loss on steam line break.

4) Permit high power operation with one line isolated.

5) Permit utilization of bypass valves (common header)

2. Reactor Head Vent

a. Operating vent

1) From reactor head to "c" main steam line. Con tinuous vent of non-condensibles which might other wise accumulate in the head area during pcwer operation.

a) Flow caused by small pressure drop bet....een tne vessel and the steam line.

b. Cooldown vent

" Fr or, reactor head to .' equipment drain s*-Z.

"/e,.zs *cn-condensinles durinc zccldcwn ..  :=r.

steam ,ines have Deen flooded and :ne reazcer ce pressuri zed.

2_. S*-'e-..

, , .'alves

" "'ocn b-a-ss Tne 7 sa'ety valves are designed to orever.: n 'Je oressurizing the nuclear steam supply sysn-r :o prevenz failure cf the nuclear syszem :rc.cess barrie- due to pressure.

_ .e'--s n *ress*'re is

-- aZs :-. ",'s-.e : -= .

code*e a zransienz over-:rss.re

condition of 10' (I) 1250 + 10f: (1250) = 1250 + 125 = 1375 psig c)The highest pressure in the primary system wifl be at the lowest elevation due to system pressure + the static water head. The highest pressure point will occur at the bottom of the vessel. Because the pressure is not monitored at this point; it cannot be directly determined if this safety limit has been violated. Also, because of the potentially varying head level and flow pressure drops, an equivalent pressure cannot be a prior; determined for a pressure monitor higher in the vessel.

2. The total safety and safety/relief valve capacity has been established to meet the overpressure protection criteria of the ASIE code.

a)The worst overpressure transient

1) 3-second closure of all MSIV's neglecting the direct scram (valve position scram)

2) ,,aximum vessel pressure of 1303 psio if a pressure scram is assumed

3) Maximum vessel pressure of 1260 psig if a neutron flux scram is assumed

4) Number of installed valves that must open to limit peak pressure to 1350 psig (25 psig margin)

(a) 7 valves must open if a neutron flux scram is assumed (b) 10 valves must ooen if a pressure scram, is assumed

3. The distribution of the recuired capacity between safety valves and safety/relief valves must be sucn that-the safety/relief valves shall prevent the operning of the safety valves d-ring pressure transients which are responsiblyv eynec.e-d during the i e-,,,E of zne r-iant l) A turDire trip from rated power wiz,.

bypass valve failure to open (assuming tur-ine trip scram) is the nost severe aDnormal operational transient resulting directly in a reactor coolant system Dressure increase.

b) High pressure switch activates a DC solenoid which admits air pressure to a remote operator.

3) Auto Depressurization a) To provide automatic depressurization for small breaks in the nuclear system so that the LPCI made of RHR and the core spray system can operate to protect the fuel barrier b) Opening action is the same as for the relief function c) 6 Safety/Relief valves operate in the ADS mode.

c. Valve Set points

1) A valves 0 1090 psig Capacity 800,000 lb/hr each

2) t valves @ 1090 psig Capacity 808,000 lb/hr. each

3) 3 valves @ 1100 psig Capacity 815,000 lh/hr each

d. Blowdown :ath

1) Individually piped to the suppression pool below the minimum water level

2) Vacuum breaker provided to allow entry of dry well air i.nto the relief line to prevent water from the suppression pool, from being "pulled" up, into the relief line upon completion of blowdown when the steam in the relief line condenses. Subsequent reopening of the valve with its relief line partially filled with water could overpressurize the relief line.

e. Valve Actuation

1) Self -actuation (safety mode) (Figure 5) a) Pressure senses a-- ilot sensing part (2)

S ows () is fcrced to the ri ct Bel if se oint is reached.

) M~oring pilot vaive disc (3) d) Allowing pressure to be transferred zc the second stage piston (2) which is forced down.

e) This vents the pressure from the top of the main valve piston (12).

-f) Venting is via second stage disc (10) and cut main v- ,,e _-i.estsr, ".,e.s.i  ;'i-'.

- P_ -

h) Dressure differential is created because of the small size of the main valve piston orifice (13) compared to the main valve piston vent (15).

i) Reaczor steam pressure tnen lifts the main valve piston (12) and the main valve disc (14).

j) Steam flows out and is piped to the suppression pool k) When steam pressure is =50 psig below set point, the pilot setpoint adjust spring (4) forces the .pilot valve closed (3).

• I) Second stage disc closes (10).

m) Pressure equalizes .across main valve piston (12).

n) Spring force closes main valve disc (14).

o) If the bellows ruptures, a pressure switch alarms at 1E0.= (5).

Pilot actuation (,Manual) a) DC solenoid admits air pressure to remote air actuator (7).

b) This pdshes down on second stage piston .(6),

c) Which unequalizes pressure across main valve piston (12) as above.

d) The solenoid is actuated by:

(1) hich Dressure - Set pressure (n'oz aDcIcal*E to Brown's Ferry)

(2) manual demand (3) "automatic blowdown demand.

ell The p*ressure sensi nga f.;v111 is. bsurdorn tube. ;f re-ctcr nressure rez.ches -;^,es-: pressure. it activa--es a sE,::'

to enercize the soienc*i.

f) of -he 6 Safety/Relief valves provided for ADS is nEach equipped with an air accumulator and check valve arrange ment. These accumulators are provided to assure that the valves can "e held one,. -o.low'inc failure of the air

' -- acZu je . as, , n he are si :eCc c:z=-. r

".-cnt ai for a -i,..* Of fiVe va:e- oe:..,S or nol;din- the valve -=en for 3 -s, . Accumu;a-ors are nut no- required for the relief valves no- used for ADS

. Stea-, Line Flow Restrictors

a. Purpose i) Limit flow during steam line rupture to --2001 ofrated line flow.

2) Limit the loss of coolant from the Reactor vessel following a steam line rupture outside the primary containment to the ex tent the vessel level does not fall below the top of the core within the MSIV closure time.

3) Limit thetP across core internals by restricting flow.

4) Provides mechanism for measuring steam flow.

a) indication b) input to reactor level control system.

5) Provides input to the primary containment isolation system.

b. Venturi-type restrictor. Pressure drop of-lO psi across the restrictor at full flow.

6. Main Steam Isolation Valves

a. Each steam line has two isolation valves - one inside and one outside the primary containment.

b. Purpose

1) Prevent exceeding radiation release rates in excess of IOCFRIO0 guidelines in the even't of a steaim line break outside of primiary containment.

2.; Limits inventory loss during a steam line break accident. Helps maintain clad integrity by preventing core from uncovering.

c. V;-'.\*ie description

'.: "4or c-s-onents aj air cylinder b) nydraulic dashpot c) speed control valve d) closing springs e' vale .sea:

-i c .r.

-" Dist valve se-t

- 10 -

2) Open valve operation a) Air supplied to underside of air operator piston causes piston and stem to move upward against spring pressure.

b) Stem lifts pilot valve first - 1/2 inch (1) equalizes upstream and downstream pressures through balancing orifice c) Upper portion of pilot makes contact with main valve body, and lifts the main valve off its seat to a full open position.

d) Valve designed to open against 200psid differential (100 psid differential by procedure)

3) Close valve operation a) Air supplied to top of air operat6r piston plus spring force causes valve to close.

b) Valve closure speed set by throttle valve on hydraulic dashpot.

in - 5 seconds.

(I) "(a) closes Valve Fast enough (5 seconds) to prevent gross release of fission products to the environs.

(b) Slow enough (3 seconds) to minimize the severity of the pressure transient resulting from isola tion.

.1' Characteristics a) Air to open.

b) Air and/or spring to close.

oj .ave f closed on loss cf air.

OnE AC And One DC solencid operated valve conzrcls aiz supply.

e) Each valve has an accumulator - check valve arrangement to supply air on loss of pneumatic supply pressure.

-a ; r* - , S S IE . I/e r, E . r, E rvwe I i y S e*.. C sP-*

• va v-es .jppiied. y r,e .o.r. r r*

- I, -

5) Air system open valve operation a) Air is supplied to air operating cylinder through an air ooerated control valve.

b) The air-operated control valves are controlled by the AC or DC solenoid operated valve.

(1) If either solenoid valve is energized, the control valves will be positioned to:

(a) supply air to underside of air operated piston.

(b) bleed off 'air from the top of the piston.

• (2) Working against spring force, air opens valve.

(3) 250 V DC supplied by battery.

(4) 120 V AC supplied by an RPS bus.

6) Air system close valve operation a) De-energizing both solenoid valves will cut-off air supply to the control valve operators causing the control valves to:

(1) supply air to top of air operator piston.

(2) bleed off air from underside of piston.

(3) Air pressure and spring force close the isolation valve.

7, Test operation a) Depressing the test pushbotton for 1A -'ain Steam Isolation Valve causes:

(I) The -est soionoid valve to energze resutino.r, air being supplied to the test control valve operator.

(2) The test control valve positions to stop the air supply to the underside of the iMSiV air ocerator piston and slowly bleed the remaining air through a needle valve.

( 7T e va'.i;e slc':v :I sE . EIS r r.-_

(4) The valve will go to the full closed position if the test pushbutton is held depressed

• 5) When :=e test push tu:ton is relex.sed, the tesz solenoid valve de-energized and air is again supplied to t-he underside of the HSIV air operator piston to open the valve (b) If the test pushbutton is held down, the valve will close in 45 - 60 seconds.

(c) Testing a valve at full power might result in high steam flow in the other three lines. It is therefore necessary to reduce reactor power to S 70% of rates power prior to testing.

8) MSIV Control Logic (for MSIV 203 -1A) - Does not Apply to Brown's Ferry a) ;Normal operation (valve open)

(1) GRI osolation contacts closed.

(2) IIlA & 112A relays energized and sealed in.

(3) Control relay CRIA de-energized.

(-L) Control switch in auto-open position (contacts closed).

(5) 120V AC & 125V DC solenoids energized.

(') Air supplied to air operator to cper M57S7.

L) Close operation (0) Control switch contacts open.

(2) De-enercized 120V Ar 12A5V C solenoids.

I Air s-p.i-.* zo air c:erator to close "'.

c) -esz operation (1) if the M1SiV is full open, momentarily depressing test pushbutton enercizes CRLA and the test valve so erc;i .

- 13 -

(2) CRlA provides the following functions:

(a) seals itself and t-he test valve solenoid throuah LSIA.

(b) de-energizes 120V AC solenoid.

(c) de-energizes 125V DC solenoid.

(3) When the MSIV reaches the 90% open position, LSIA opens.

(a) This de-energizes CRIA and the circuit returns to a normal configuration with the MSIV open.

.(4) Holding the test pushbutton down continuously acts as a bypass of LSIA and the MSIV will slowly close.

d) GR I Isolation (1) Arranged in a one-out-of-two twice logic, the 106 acontacts open on Group I isolation and cause:

(a) 112A & IlIA relays to de-energize, sealing in isolation.

(b) 120V AC and 125V DC solenoids to de-energize.

(c) Test valve solenoid to de-energize (if energized)

(d) Air supplied to operator to close valve (along with spring pressure in 3 - 5 seconds.

(e) To reset af:er GR I isolation has cleared, turn the main Steam isolation reset sw.,itch zo ener-ize octh intoard and outboard valves.

(f) 100A contact closes and picks up zthe 112A re lay, and allows the 120V AC & 125'V DC solenoids to pick up, opening the ýMSIV.

";N Si"ral which cause au-:cma:i: clos.=re of "SV's are:

Ej Low-low reac:or water level (4901) (Tech Spec 49**1 b) Main steam line high radiation (3 x normal 103. radiation level)

-e.-nr. . , , -- . .-c. 2

d) High steam flow in any main steam line (140%) (Tech Spec I*0*).

• ... u_ '825

_ * ...... equalizinc header pressure osi)

' Low -pressure (1) bypassed in all modes except run.

f) Manual

10) Reasons for isolation signals:

a) 490" reactor water level (1) Low enough to prevent spurious initiation.

(2) High enough to initiate isolation (and ECCS) so that:

(a) .no melting of the fuel cladding occurs.

(b) post accident cooling may be accomplished and the guidelines are not violated.

N:ote: IOCFR1O0 cuidelines define an exclusion area so that any individual on the site boundary for 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> immediately following the onset of fission product release would not receive a total radiation dose of greater than 25 Rem whole body or 300 Rem to the thyroid.

b) 3 x normal high radiation (1) de-ec: gross fue! failures (2 prevent exceeding "OCFI100 Cuid~rines c) 200,F steam tunnel higrh temperature (I) detect small (15 9pm) steam leaks in steam tunnel.

pro) prvi.e backu- hirh szeam fcw isoIaticn on aarce breaks outside ccntainment.

prevent exceedin- 10 CFRIOG cuideiines.

d) lAOI steam flow

-. -; - _c -=.,

.,,-.. r, .r unc-icr.::r ah

.' s- i - r- -,

s---an isclatiorn . C-Oe5, lEi- tne -ass invent-cry lo-ss s-jcn -a-:

- 15 -

(a) fuel is not uncovered.

(b) fuel temperatures remain less than 1000 F (c)- IOCFR1O0 guidelines are not exceeded.

e) . steam line pressure with mode switch in Run (1) protects against a failure of a pressure regulator which would cause the control and/or bypass valves to open.

(a) limits inventory loss so fuel is not uncovered 0 (b) peak clad temper.atures are much less than 1500 F.

(c) There will be no fission products available for release other than those in the reactor coolant, therefore 10 CFR100 guidelines will not be ex ceeded.

(2) Prevents rapid depressurization and subsequent cool down of the reactor vessel at rates exceeding the design rate of change at vessel temperature.

7. Steam Line Drains line

a. A drain line is provided at the low point of each main steam as follows:

1) upstream of the inboard isolation valves.

2) downstream of the outboard isolation valves.

b. Line Draining

) A combined ;0 valves (25 valve) is Frovided for the above if sea- drain lines for rapid draining of -he steam lines flooded.

2) Drains go to the main condenser.

3) !hen plant is o;era:ir,;, crain path is throug; crie,:es to tne condenser.

if

4) Each downstream drain line has an isolation valve so that at power, its drain an individual line has to be isolated valve can be opened.

a) Prevents t isclated line -rcon filling uo -nith con

e

-asS-0-ni-'- --

• -16

c. Drain valves also have equalizing function.

1) Recovery from main steam isolation a) check common drain line to condenser closed (58 valve) b) open outboard isolation valves.

c) open drain valve 457 d) open drain valve #56 e) open drain valve #55 to pressurize the main steam piping and equalize around the inboard isolation valves.

Sf) open inboard isolation valves when pressures equalize (within 100 psid).

g) open drain valve #58 "Note: Turbine drain lines will be covered in turbine lesson plan.

N',ote6: NPCI, RCiC drain lines will be covered in their respective lesson plans.

8. HPCI Steam-Line

a. 1'" line off the "B" main steam line

b. Supplies steam to the HPCI turbine

9. RCIC Steam Line

a. 3" line off the "C" main szeam line

c. Supplies steam to the RC:C :urbine

!l. Pressure Equalizing Header

a. Smaller pressure transients experienced when testincgSi's and

-- rbine s:c- aEnt con.roi valves.

I'. Bypass valves

a. valves with _2: relief capacity (total)

I) Discharge into the main condenser via pressure reducing orifices.

a. St=ean jet air e=ect:rs

- 17 -

1) Ist and 2nd stage SJAE Supply 200 psig

2) 3rd stage SJAE Supply 200 psig

b. ECHAR off-gas pre-heater

1) 250 psig steam supply for pre-heater

c. Gland seal steam

1) Pressure control valve supplies 3.50 turbine shaft sealing steam.

d. Turbine driven Reactor feedwater pumps

1) 6" Supply line

2) Supplies high pressure steam for Reactor Feedwater pump turbines, A, B, & C

13. Turbine Stop Valves & Control Valves

a. Covered in Turbine & Electro Hydraulic Control Lesson Plans F. IMSTRUMENTATION

1. Control Room Indications Instrument Type Range Steam line flow 4 indicators 0 - 4 x 106 16/ hr Total steam flow recorder 0 - 16 x !06 16 Ohr Turbine throttle pressure 1 indicator 0 - 1200-'

• Safety & relief valve multipoint 0 - 6000 F temperatures recorder Main* SZ*ET line 1 meter 0 - 106 mrihr radiation 1 recorder (6 decade log scal*)

0

-Steam tunnel temnerature recorder 0 - 600 F

• Lccated on back panels

- 10 -

2. Local Indications

a. Turbine building Instrument Type Ranoe Main steam header gages 6- 1200o pressure transmitters 0 - 1200#

EHC pressure

3. Significant Interlocks, Trips and Alarms Item Setpoint Function Safety &,relief valve 1500 F Indicates possible leak high temperature alarm age past valve. Verifies valve open.

140% of rated Initiates Group I isolation Main steam line high flow steam line flow Indicates possible break outside containment.

Main steam line high Alarm 1-1/2 x Alarm alerts operator of normal trip 3x possible fuel damage. Trip radiation 1) Group 1 isolation normal (;formal is initiates average reading 2) Secures .echanical vacuum 100f power) pump and valving

3) Isolates Condenser air tray

4) Closes off-gas system stack isolation valve

.oni tor Al arm Trim

.~-90-1 36 637 Mr/hr -1275 Mr/hr RI-90-1 37 -637 1Mr/hr 1020 RM-90-1 38 '637 ,,r/Hr 2705 1275 PI-Ir-129

• 537 M1r/Hr low pressure Alarm & Trip Tf mode switch is run

",air. se. initiates Grcup i isola tion. Prote::s aa-rinst raPie cooldow.n due to failure of pressure regulator.

901! open Scram reactor on certain

![-i- stea- isolation

<'-:.Z and -cze closure.

switch not in Run.)

- 19 -

Instrument Type angae Steam tunnel high Alarm 1500F Alarm alerts operator to zen erat, re Trip 19"°F possible steam leak in tunnel. Trip initiates Group I isolation, indi cates steam leak in tunnel outside of contain ment.

G. OPERATIONAL

SUMMARY

1. Normal Operation

a. All MSIVI's open.

b. All safety, relief and safety/relief valves closed.

c. All drain valves closed except 57 and 59 valves

1) provides continuous low point drain path

d. Bypass valves closed.

2. Operation with Isolation Valves Closed

a. Closure of one main steam line will never cause a scram.

b. Closure of 2 main steam lines may cause a half-scram

c. Closure of 3 or more steam lines will always cause a scram.

d. Reference to Reactor Protective System Lesson Plan.

Note: Scram occurs due to isolation valve closure if reactor pressure is 1055# or if mode switch is in Run.

3.Grou: i "sol aio n

a. t.:cn receiot of a Group i isolation signal, these valves will aj:oma-icaily close:

1' all RS!V's 2j --E & =56 main steam drain valves

2) Reactor water sam'.,e line

.2 -'*i* resJlzinc fre n'.-..' clcsure

1 *,.=

an  : ,7- close (foil . ",S-

51. --. ,, an-= osi-i -n.

closed or open.

- 20

a. Relief valves may sometimes be used to control pressure when isolated.

a. O:erator should alternate relief valves every 5 minutes.

,; .,ra:er In suppression pool may overheat locally.

a) Could damage the coating on the inner surface of the suppression pool.

b) Could release free steam to the torus.

5. Do not allow steam lines to become flooded when Reactor is hot due to possible lifting of safety valves and relief valves.

H. RELATIONSHIPS WITH OTHER SYSTEMS

1. Main steam system is part of primary containment.

2. Steam flow signal provided to:

.a. Reactor level control system.

b. Primary containment isolation logic.

S3. Limit switc~hes on 1SIV's provide position input to the Reactor Protective System.

_1. Main steam radia-ion monitor provides signal to:

a. Primary containment isolation logic.

b. PReac-or protective system.

c. Cff-cas isolation logic.

pressure Press-re equalizing header is source for turbine EHC system sicnal.

-.a'ar:e of p,ant steam supplies:

. f-c-as ystem

is-t and 2nd stace SJAE 2; 3rd stage SJAE

.-.- ,, etoreeahet=-rer

-. *ine ýriven Reactor -f=ec"...ae ,*um,,s.

c. Gland seal steam

d. MPCI turbine

e. RCiC turbine

7. Safety-relief Valves

a. Part of the Emergency Core Cooling System (6 S/RV part of ADS)

1) Required to reduce pressure to permit low pressure systems to inject into the vessel.

8. Bypass steam to condenser

9. Air Supplies

a. Drywell control air supplies the inboard SMIV's and the Target Rock Safety & Relief valves.

b. Control air system supplies the outboard MSIV's RPS bus supplies 120V AC solenoid valves for MSIV's.

250V DC battery supplies 250V DC solenoid valves for MSIV's.

"TECHNICAL SPECIFICATIONS

1. MSIV closure scram shall be -IM! valve closure from full open.

a. This scram anticipates the pressure and flux transients which occur when the valves close.

b. Automatically bypassed if i055;4 steam line pressure and mode switch not in Run.

i) Plant is stable if 3055= with -¶S!V's closed.

2. -Main steam low pressure initiation of Group I isolation shall be a25::.

- the oressure reculator fails in a manner which causes rapid cepressurization, excessive cool dz'irn rates may be enccuntered.

b. Automatically bypassed in any mode switch position except R.un.

1) Allows plant to heat up and pressurize.

Ei n St-E- line hich radia:i:n set:oint shall e -i-3 x nor-a!

. :ni-ia:es Grouo I i-sclazicn.

b. Scrams reactor (direct scram).

- 22

c. Alarm shall be 1-1/2 x normal.

d. Normal is background radiation level at rated power.

e. "solates off-gas system

4. High flow main steam isolation shall be 140% of rated steam flow for that line.

.a. Isolates a break outside containment and limits radioactive release to the environs.

b. Conserves reactor coolant inventory.

c. Prevents excessive P across core internals.

5. Steam tunnel high temperature isolation shall be 2000 F.

a large

a. Isolates small break outside containment before it becomes one.

"b. .Acis as back-up to i-0.' steam flow isolation.

top of

6. Reactor Low-low water level trip setpoint is 129.7" above the the active fuel. (-38" on instrument)

a. Isolates main steam isolation valves to conserve inventory.

irradiated fuel

7. Maximum allowable reactor coolant system pressure with in the vessel is 1250e - 101! transient overpressure.

a. 1250-:. + 125= = 1375=

b. Highest pressure in vessel is in ztto-, head region.

c. Pressure is sensed in steam dome region.

li.it is in

d. The recirculation system piping's tr-Ansient pressure Cxcess of 1375 psig.

plar.s.

For further information consult R"S =nd ?C1S Lesson

. a---v Valve Sezpoints

a. Safety valves - 2 valves 9l,250 psig "33 ,al"es ? 105 :,SZ vvs.-,15

~~~~ j )s I 3; 3Valves 3 1,125 :Sic

c. Bases

1) The total safety/relief valve capacity has been established to meet the overpressure protection criteria of the ASME Code.

2) The distribution of the required capacity between safety/

relief valves and safety valves has been set so that the safety relief valves will prevent opening of the safety valves during normal plant isolations and load rejections.

9. When more than one valve, safety or safety/relief, is known to be failed, an orderly shutdown shall be initiated and the reactor depressurized to less than 105 psig within 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />.

10. At least one safety valve and approximately one-half of all safety/

relief valves shall be bench-checked or replaced with a bench checked valve each operating cycle. All 13 valves (2 safety and com 11 safety/relief) will have been checked or replaced upon the pletion of every second cycle.

shall be

11. Once during each operating cycle, each relief valve valve indicate manually opened until thermocouples downstream of the steam is flowing from the valve.

be con

12. The integrity of the relief/safety valve bellows shall tinuously monitored.

insoected each

13. At least one 'relief valve shall be disassembled and operating cycle.

System 1L. Five of the six valves of the Automatic Depressurization shall ne operable:

a) pricr to a startup from a cold condition or, vessel and b) -!henever there is irradiated fuel in the reactor psic, exce-,t as the reactor vessel oressure is greater than 105 15 and 1E.,

snecified in requirements of autc"at -C.eratin*o I. Tf -v.O ADS valves are known to be inc"paDe not to exceed 30 the reactor may remain in operation for a period days, provided the HPCi system is operabie.

of automatic

16. If more than two ADS valves are known to be incapable a period not to in operation for overation, the reactor may remain 7 r. .  : S C e H..CC h*'a n r.er sn C;, .-E 1 . f enzs-15 ar., 16 cannc t L*e e E eir 7ir red,. ce t ini-iated and the react-or vessel pressure sh.l, be osig or less within 2L hours.

Revision Date BWR SYSTEMS LESSON PLAN m*.AIN! TUPDBINE.

B. REFERENCES

1. BWR Systems Manual Chapter 2.6

2. Browns Ferry FSAR Chapter 11.2

3. Browns Ferry 01's 47 and 3

4. Peach Bottom BWR Discussions Chapter 6.3 C. -10iECTIVES

1. General Description

2. Flow Paths; Steam and Auxiliaries

3. a.Jor Components

4. Auxiliary Systems

5. Turbine Trips

6. Reac-or Scrams Originating w.ith the Turbine

7. Technical Specifications Associated with Turbine and Auxiliaries D. BRIEF DESCRIPTI*N

1. Purpcse:

To c:rvert thermodynamic energy of the reactor szeam into mechanical enervy :o drive the main generator.

2. Sasi Descorption (Fi-ure. 1'

a. cmne high pressure (HP) section as A.,

b. -hree low pressure (LP) sections identified consecutively 3, and C from the HP seczion to the generator.

c. icrn rsm

S- 2

d. Tandem-compound, Six-flow I) Tandem-compound means that each section is aliened on the same shaft and'zhat stea.m !eaves the HIP section before ex pansion is complete and then goes through one or more LP sections.

2) Six-flow means that the steam enters at the middle of the LP turbines and flows in both directions.

e. Ion-reheat; steam is not reheated before returning to LP turbines.

f. Last stage buckets in the low pressure turbine are 43"

g. Approximate steam conditions:

1) 950 psig throttle pressure at

2) 13.37 x 106 lb./hr. steam flow with

-3) 0.281: moisture against a maximum L) Back oressure of 2" Ho absolute in the main condenser.

3. Steam Flow Path

a. From four imain steam lines (2!") to

b. Turbine Throttle (2a")

c. 'E" lines to byoass valves fro. throttle (9 valves 2E"' design capacity)

d. - " lines to

1) Off-Gas Preheaters

- jr-*ne -i-h Pressure Steam "hrott-es "7 --ea tcr Peed Dump Seal Steam 7eGulators

-) Steam let Air Ejector .ecuiators

e. Thrcugh main stop valves to

-ss' s- -*c. JA,.. *S -

g. Through the contVl valves

h. Through the high pressure turbine

i. Exhausts to the moisture separators (6)

1) Extraction steam from B1 and C1 crossover lines supply reactor feed pump turbine low pressure steam throttles (250 - 275 psig setpoint).

six

j. Dried steam is admitted to the low pressure turbine through combined intermediate valves (CIV's).

k. Low pressure turbine exhausts to the main condenser.

for

1. Extraction steam is drawn from various low pressure stages feedwater heaters.

4. Other Tandem Mounted Components

a. Generator, a four pol, 1,280 !IVA at .9 power faczor, hydrogen cooled with liquid stator coolant.

b. Exciter, a four pole, 2635 KUI, air cooled, 0.97 power factor, system.

60 cps, wye conniected, alter ev (alternator) excitation

5. Other Components

a. Low pressure relief valves

1) Set at 250 - 275 psig ccntrol valves

2) Protect :he L? turbine casing if the main stop and remain open and the CIV stop valves slam shu-.

b. Bearings

1) TIIeive spherical seat- journal bearings middle

2) A taoered-land thrust bearing mounted at the fixed standard.

z,?,PONENJT DE3CRIPTIONr Z.

1. Turbine Stoo Vailves (Figure 2)

S° "*n . - °

b.

Purpose:

These are emergency valves and function to :rotect the turtine from fault conditions such as overspeed which could be caused by

1) Failure of the control valves or,

2) Generator trip.

c. Construction

1) All four stop valves are welded together at the below-seat equalizer and thus have interconnected flow paths.

2) Each valve is controlled by an operator at the bottom of the valve via the Electro Hydraulic Control System (EHC).

3) Hydraulically operated open and clcsed, spring loaded closed.

4) Valve Number 2: (Figure 3) a) Has an internally mounted pilot valve used for admitting steam to warm the steam chest.

b) Also used to equalize the pressure across the stop valves orior to opening as tne valves are designed to open only if the L.P across them is <130 psig (=13% of rated steam, pressure).

2. Turbine Control alaves (Figure 4)

a. uantity is L.

b.

Purpose:

To reaulate the steam to the turbine within the cama'il'tv of the reacocr to sj;pv seam tCrie*,, on-rciiir, reactor

ressjre.

£" Aisc Drovides -ne control for rollirn, syncnronizinc and loading of the machine.

c. Construcoionf:

1 Valv;es are weldced directly to t~eir res;ective st; ,'7ives

• al*; via the E-rc *ysm .

3) Hydraulicially operated open and closed, spring loaded closed.

.) Balanced with internal poopet and balance chamber.

a) When steam is admitted to the steam chest some passes between the valve and valve skirt to pressurize the balance chamber.

b) During valve operation the internal pilot (poppet) valve moves less than 20 mils.

i. Steam is bled-past the stem and out the pilot valve seat to the outlet reducing balance chamber pressure.

ii. The valve then opens against less back pressure.

3. Combined Intermediate Valves (CIV's) (Figure 5)

a. Quantity is six (6)'.

b. .Purocse:

1) To protect the turbine from overspeeding during a generator trip or load reject (Load dump).

valves

2) The overspeed might occur even if the stop and control in the moisture sepa close due to flashing of t1e moisture, drops within the turbine, rators, to steam when the pressure the con oiping and moiszure separators due to the vacuum in denser.

c. Construction i ) Two valves in one:

a) Intercept valve t' Stoc valve 2 :ntercept Valve A-) Balanced sieeve type holes

i. Steam pressure is equalized across the valve, by throuch the mid-valve plate, balancina the valve.

Si.*.e~ve - a n.: a C/. .", - r

b) Variable position valve that regulates turbine speed during overspeed conditions.

i. Slow increase in speed.

aa. Remains full open until -1051 overspeed.

bb. Ramps closed and is full closed at-107$ overspeed.

cc. Begins to re-open at -102% overspeed, decreasing.

ii. Fast increase in ipeed.

aa. Begins to ramp closed 102% overspeed.

bb. Begins to re-open at-'lO2%overspeed, decreasing.

c) Normally full open valves.

i. Ramp open when turbine speed is selected.

ii. Valves Al, Bl, and Cl open first.

iii. Valves A2, B2, and C2 begin to open when valves Al, 1BI and'Cl just reach the open position and valves A2, B2, and C2 will close smoothly when valve Al, B1, and Cl close below half stroke.

3) Stop Valves a) Unbalanced Disc - Ecual pressure across the ',alve is noz required as the valve is ei-her full open or full shut.

b) Closes on a turbine trip.

c) Strictly an emergency valve.

11 Each valve is controlled by an on-erator a- tottor o' :he val ye.

-} Hydraulically operated open and closed, spring loaded closed.

4. Associated Valve Equipment 2=ke Strair*ers

_ ur:ose is to oreven: -inie:ion o- foreign _ a-erIal -. rcj:;

.alves to -urbine.

re-o;ed fo,,owir.: ;-.--al z'Jr*_I:e  ::rS-'2 .

"11 Usually available for re-installation following maintenance.

b. Valve Linkage

1) On all valves except bypasses.

2) Purpose is to provide valve control as valve parts are differ entially expanding and contracting during heatup or cooldown.

5. Turbine Inlet Relief Valves (Low Pressure Relief Valves)

a. Quantity is 6.

b.

Purpose:

Protect the turbine low pressure piping and moisture separators the from overpressure which would occur if the CIV's failed in closed direction with steam still being supplied to the high pressure turbine.

c. *Pressure setpoint is 250 - 275 psig.

d. Discharge of the valves is piped to the main condenser.

6. Extraction Non-Return Valves (Figure 6)

a. rantity: (9) to One on each extraction steam line from the LP turbine section zhe 1, 2, and 3 feedwater heaters in each string (A, B, and C)

b. :yr~ose:

when the To protect the turbine from overspeed which might occur and subsequent lowering of oressure in the zuroine is trip-ed results in

-urine and hW:aers (due to vacuum in the condenser) of fasnine of the moisture in the heaters to s-eam and passage and Cn to

=is szeam back inWo tSe turbine, thrcogh the bla-ing

ne condenser (forE ir. fee;:ater system L?).

c. S:nstruction

1) Ordinary check valve S'Ai zyline- on th-e Ysc .

kCse=M i~cV " tst U: Out C? ths "!Q-!!

_ "-!r .... relzac  ::  :

nc:z--. 040 *z

a: usr-ra

". A!hen turbine.trios, air is bled off from Whe air cylinder path.

- alowin; e disc to fall:artiaill crcwn into the flow

f r....5 s E fl.:cw

':a Cccur" She di: slams sn-.

7. Bypass Valves (Figures 7 and 8)

a. ý,uantitj is 9.

b. Bypass capacity is 25% by design.

c.

Purpose:

1) To permit establishing a flow of steam to the condenser in preparation for rolling and loading the machine.

2) Also handles excess steam while unloading the machine or duri.ng a turbine trip (a't low power).

3) Used for passing steam to the condenser on a reactor cool down for decay heat removal.

d. Construction l) Physically located above the turbine throttle. (Figure 9) a) Numbers refer to opening sequence.

b) Discharge is to condenser through pressure reducing orifices.

c) All bypass valve inlets are welded zogezher forming a header.

2) Valve Assembly (Figure 8) a) -re operated sequer.tiai!y -y EHC oil pressure.

aal-,es b) Flow path is from inlet header to main condenser:

Turbine Valve Lineups:

See Ta-ie I.

-. Hich Pressure Turbine Section (Figure 9)

a. Sonsists cf:

i) Front Standard (1)

"-j Stear. inet

- ( "urtine - i"s"

-g-

4) Exhaust to moisture separator (17, 18, and 19)

5) Journal bearings (2 &,lO)

6) Thrust bearing (12)

7) Thrust bearing wear detector (11)

8) Coupling to LP (15) four lines

b. Steam is admitted to the turbine admission bowl through the turbine.

at equal circumferential -intervals at the center of This. is called full arc admission.

c. Each end has six stages.

tips. Drains

d. Each stage has moisture removal by annuli at blade internally to last stage.

provides the only

• e. A journal bearing at each end of the HP section for the rotor. Mformal bearing oil temperature is

-vertical support 0

1500 - 160 F.

psig and 14.s' moisture

f. Steam exhausts to the moisture separators 192 goes to six moisture separators.

10. Thrust Bearing 3 between the HP and first LP

a. Located between journal bearings 2 &

turbine (A). (Middle standard)

b. =uroose:

and generator rotor in To prevent any axial motion of the turbine rotating blades and order to mainzain proper' clearances bet-..ieen stationary diaphragms.

c. :xiai thrus- can occur, for example, due to imbalanced steam ex

-raction.

on the bearing %.,ill detect

d. A thrust bearing wear detector locate, in either direction and excessive thrust bearina wear (1-.025")

wiill trip the turbine. (Operation covered in G.A.a:)

thrust bearing by seoarate

e. 3-earing oil at 25 osi is fed into the

.- .s orr . :-, e ra-*a rise BI.c., - t1 e-cee-

- 10 -

Each thrust plate contains two thermocouples embedded in the plate backing metal. These thermocouples serve as an additional tempera ture indicating device for the bearing.

Normal temperatures 140 - 175°F 125 - 150OF (Unloaded plate)

High temperature alarm 180OF Maximum operating 190OF

11. Front Standard

a. Located on the end of the high pressure turbine.

b.

Purpose:

To house various turbine control components such as:

1) Hydraulic trip system

2) Auxiliary control rotor gears assembly

3) Mechanical trip and reset device

-1) Oil trip and reset valve

5) Overspeed trip device

6) Eleczronic low speed switch

7) Speed sensin-g head E' t'ain oil pump

9) Torque shaft, levers 10" Shell expansion deteczors

.) -ifferential exoansion detectors

12) Oil caces and valves

13) Shaft Groundinc Device--This device consis-s of a sprinn-loaded flood lubricated shoe witn silver ribbon inserts. These spring loaded shoes run on the turoine stub shaft extension, on the front _tandard. The oil film is thin enough so -hat an adecuae

°- -.

C'"* ----. - ,-----_-£ r ._ ------------

r.ccd

-.'- r .'c'~~~~~~~~~--- ,':---,*_zT --

.coronen:s wili be discussec i detail with h-e -*C Sstem.

12. Moisture Separator

a. -here are six units.

b.

Purpose:

To remove moisture from the steam before entry to the low pressure turbine.

c. Moisture Removal Section

1) Peerless type moisture removal sections.

2) "Fish hooks" remove moisture which is piped to the moisture separator drain tank. (Same principle as for reactor vessel steam drier assembly.)

3) Dry steam passes to the low pressure turbine.

13. -Low Dressure Turbine Sections C (Figure 10)

a. Consists of:

1) Journal bearings (20, 28) 2') Eight stagis (7 through WL)

3) Atmospheric relief diaphragms Moisture removal annuli M) (30)

- -otcr coupling (27)

b. -here are three LP sections.

'nits are designated A, B, and C starting from the HP end. Each c.

section has eight stages (7 :O.rsugn lz). Last stage Wiading is

d. SOeM- is av.it-e- ZO each LP :-*rire in two lines throu-h te

e. Exnaust is to the individual sec-ions of the main condenser.

V rYer casing heods the stazicra.ry diaohrags.

1:Vannels sMan :0 W~E ccrn:erser ard provices a neans Hsealing

-. e ' zcr _-ha7-.

c.ensr ressure-

4- --------------..

- 12

h. Moisture Removal

.) Each stage has a moisture removal annu'-s.

2) The collected moisture drains to the feedwater heaters at designated points.

i. Overpressure Protection

1) Each of the outer casings- has two azmospheric relief diaphragms.

2)

Purpose:

To protect the exhaust heed and main condenser from overpressure and which, for example, would occur if condenser vacuum was lost steam continued to be sent to the turbine.

3) Consists of a copper-silver alloy sheet.

• ) Under normal conditions with the condenser at vacuum, the dia phragm is dished inward.

diaphragm 5" On overpressure of 5 osid from within the exhaust, the a cutting knife thereby opening the is forced outward against exhaust of up to rated steam flow.

relief diap'hragm permitting 1-1. Turning Gear

a. Located between the last LP turbine (C) and the generator.

b. 'urpose:

is shu-dcwn 7o sI-c-,i ro-ate the reac-or a: 3 to E r=m -. en machine

o orevent rotor bowing.

c.

Description:

• . A: -,otor d-ivir: a ::in-n :-ear that meshes :i-b

-he 2,

.ur:,ine shaft tu I ear.

d. E-gce.Enz - Disencacement reacnes 0 rpm i) Automatically engages on coast down when machine to an air air by operating a solenoid air valve which oorts "Ca".e, -z*.':] ' enca*--' '-a cze-:*i2- "f -.- e sam,, sz'.rc: 3 E bC Ve.

=n be i en2a-4/ l~ via so'enoiý direct.ly ccnected aen be - lar.-aly ,. . . .

th~e ,ana: ,ever.

- 13 -

4) Can be manually engaged locally with a wrerch on the squared end of the external projection of the torque shaft engaging.

.mechani sm.

5) Automatically disengages upon rolling of turbine.

e. Interlocked to prevent operations unless bearing oil header pressure is>lO psig.

4 gpm

f. Receives constant lubrication from the bearing oil header at through a restricting orifice when header is pressurized.

15. Control -Room Instrumentation Item Device Rance a.

Turbine Throttle Pressure (2) Indicator 0 - 1500 psig a.

b. Steam Chest Pressure indicator 0 - 1500 psig

c. Turbine Speed Indicator 0 - 2500 rpm Recorder 0 - 5000

d. Turbine Speed/Valve Position I) Red Pen Turbine Speed/Control Valve Opening 0

2) Slack Pen Bypass Valve Opening 0 - 1300" Indicators 0 - Ioo:t

e. ':alve Position "2 One fcr Each StoC, Control in" -:e=ia-e Stop, internediaze

.Control, and Bypass Valve Lbration; Eccentricity

,,:rbine Recorder 0 - 15 mils f.

S-bi ne T=-:er-ature, Di fferenti-1

'Ccr. Rcor-er Pt - 1 0 I) Shell Expansion

2) Differential Expansion Pt - 2 0 - 0.5" 7nsrorn

_-,e-. i*.*. - -_ - - - -

T-  : T:*- . :

- 14 -

.. TURBINE .aUXTLIARY SYSTEVIS

1. Exhaust Oood Spray System

a. Purpose During machine startup or at low loads, steam flow to the last few stages of the low pressure section is so low that:

1) Little cooling of the blading is provided by the steam and

2) The blades in the last 1 - 2 sections are actually pumpi.ng the steam through the machine (not designed as pumps).

and This result in significant heating of the last stage blading inner casing.

of Some cooling must be provided in order to prevent distortion radial and axial shaft to casing clearances.

Problem is worsened if have sionificant non-condensables in steam.

b. Brief Description System consists of:

I) Temoerature sensors in the A & C low pressure hoods to detect hich temperature conditions. The highest reading detector con trols the automatic spray system.

spray

2) An air ooerated, temperature controlled automatic.. the val Je that controls the flow flow of derniner3iized water from tC s,-=,...

cn , ,,-s**- is i'- cpm at 100 ;sig with "loaxi-um no load on the turbine.

the

3) A mozor operated bypass valve is provided for bypassing auzc-.,atic spray valve in the evenz of its failure.

C1 IT13 is -i r no not use bypass valve if exhaust hood temperature and turbine-generator is "eaded.

hood, L) Spray nozzles that spray down into the turbine exhaustc Irovide .oonl:

indirect

,c the I =dinc or casin'. aný thus

,rurert air is used z-o.r syszem control

- 15 -

c. Control Room Instrumentation iter,Tevice Rance Exhaust Hood Temperature (3) Indicators 0 - 3000F.

d. Significant Interlocks

1) Automatic Temperature Control Valve 0

a) Begins to open at.120 F.

.*b) Is full open at 2000F.

2) Alarms in Control Room at 1750F.

3) Turbine is tripped at 2250F.

2. Turbine Lube Oil System (Figure 11)

a. 'Purpose To supply oil to the followinc:

1) Turbine and generator bearings

2) Thrust bearing and thrust bearing wear detector

3) Overspeed trip reset

) Oil to test the mechanical overspeed trip device 5' Turning gear

b. Brief Description (Figure 11)

Consists of the following components:

a) 'ain lube oil tank

2) ",ain shaft oil pumpL (rSOP)

3) Oil driven booster pump

-, s .31.ic

-c p ui,,

(S

.rn: n ceAr oi -m T*:

4" -_-ercency _earing oil pumr E*

7, searing lift ;ups

- 16 -

3) Oil coolers

""apor extractor

10) Oil purifier and purifier pump

11) Clean and dirty lube oil storage tanks and transfer pumps

c. Flow Path

1) Prior to Rolling Turbine a) Turning gear is engaged and turning.

b) TGOP is providing lube oil to bearings at'-"40 psig at the tank.

c) Lift pumps are providing high pressure lifting oil at bottom of bearings.

4 d) Motor suction pump is running providing' 20 psig at MSOP bearing lubrication.

2) When Turbine is on Line (At speed) a) MS.OP provides oil at 225 psig to booster bypass and baffler valves.

b) Booster baffler reduces the oil pressure to the oil driven turbine of the booster pump to.-l15 psig.

) Oil exiting the turla-ine enrý of the Durp coes to :ýe coolers

.hen on to the bearing heacer-'-40 psig at the tank.

d) Raw cooling water to the oil coolers is :hermocouple con 0 F. of the trolled to maintain oil tem.nerature at 100 ou:

coo ir.

e) Oi1 from the boos-er punp sup1,ies oil -o the suc:'cn .,

the MS'OP at-20 Dsig.

f)otor suczion pump, turn.ing :ear cii punp, emergency :earing oil pump and lift pumps are off.

' ,ri-* urti ,,_ "o a 2-c.,-- 7:7; :.i. -Lrt '- -r".

"-. ' 'I aUtOIati.-ii/ cae -  :] -  :  : -:.z:;or.

-o raintain suction pressure to "K0? to prevent :ara:=.

1 TGOP w.!l autoratica-l/ st-ar: a--:l::" : ' -arinc he-ad

-res__'re to -reven- 5earir,:a.aC.

• -17

d. Component Description

1) gain Lube Oil Tank Capacityi a) Operating Level 11,450 gallons b) Backflow to tank when shut down 3,500 gallons c) Total System capacity 14,950 gallons

2) M~ain Shaft Oil Pump (MSOP) a)

Purpose:

In conjunction with the turbine driven booster pump, satisfy all lube oil requirements while the machine is at speed without reliance upon electrical power.

b) Located in the front standard.

c) Double suction, single stage, centrifugal pump driven at 1800 rpm by the main turbine shaft.

d) Provides adequate oil pressure and flow sufficient to meet lubrication requirements when at 90'. of rated speed.

e) Discharge pressure is,-225 psig to the booster pump.

2) Oil Driven Booster Pumo and Baffler Valves a)

Purpose:

in conjunction with :ne X.501P, provide complete oil supply

• ,.ihouz relianc- upon eaectricai power when the machine is on the line.

l) Pump has two functional sections:

7urtine end:

Drive pump end and also provides low pressure oil to the bearing header at 50 psig at tank level.

2) Pump end:

~-cvides oil "- u:-'cr :f "- st .2S T~e *ocs-er baffier ,,'.'e :rovide-s 'cr prc;er aJus-menl CT 1ieflow to the bccsrer pu-.p turine.

- Te *ooster affier *b:ass valve contrcls oil fow to the

- 18 -

4) Motor Suction Pump (MSP) a)

Purpose:

To provide oil to the MSOP, to provide adequate suction pressure, whenever the turbine is at<90% of rated speed.

b)

Description:

A 60 Hp. AC motor driven centrifugal pump having a discharge pressure of-'40 psig.

c0 Power Supply:

480V AC Unit Board lB. A bus not normally supplied by the diesel generator.

d) Starting: Auto if Main shaft oil pump suction pressure

<10 psig.

5) Turning Gear Oil Pumo (TGOP) a)

Purpose:

To provide oil to turbine bearings and lift pumps when machine is not at speed.

b)

Description:

A 60 Hp- AC motor driven centrifugal pump having a discharge pressure of--40 psig.

c) Power Supply:

480V AC Shutdown Board IB. From a bus which can be energized by the diesel-generator.

c Starting: `uzo when pressure at tank<15 psig. c

5) E-ercer.cv Bearina Oil F:mm (EBOP) aj

Purpose:

bearings in To provide lube oil to the turbine and generator the event of a loss of all AC power.

ith a A aO 'J ., 35I.A, DC sincle s-,age cenzrifucal puo:,

discnarce cressure f,-30 :sig.

- 19 -

c) Power Supply:,

DC From 250V DC Battery Bus 4 normally, alternate 250V Eattery ous i.

d) Starting: "Auto if TGOP discharge<l0 psig.

7) Bearing Lift Puwos a)

Purpose:

bearing To provide high pressure oil at the bottom of each the rotor up off the bearing-'3 - 5 mils to physically lift the turning gear, in order to reduce when the machine is on rotor/blade chatter and turning gear torque.

b)

Description:

pumps Five 10 Hp.*AC motors drive 10 positive displacement (one for each turbine bearing).

c) Power Supply:

i. Pumps 1-6 from 480V AC RMOV Board 1A.

ii. Pumps 7-10 from A8OV AC RMOV Board B.

generator.

iii. From a tus which can be energized by the diesel d) Suction source for pumps is bearing oil head2.'

e) Startinc:  :-,os auto start when turning gear engages and star-s performrance

.OTE

Operation cf the pumps will not affect rotor be pump ooerability at speed, and it is recommended that lift pumps should Generally lift checked at least once per month.

be ocerated any time turbine soeed is 200 rm and at all If on turning cear and cne

.*.en the u'i

is on turnina cear. be left pumps are not available, the unit may or more lift nor is no shaft chatter, on turning gear as long as there exists ant current. if chatter excessive :urniing gear motor a--f oil tempera:res W are 3-90OF the unit should be taken ing gear and rotated 1800 every i-s-minutes.

E' C"^  ! rs

-j.;ose

!etween

-o -,.irtair t'he lube oil bearing inlet temoeratbre 0o.-

b)

Description:

i. Two 100q capacity coolers, each submerged in the oil tank.

ii. Cooled by raw cooling water at 3500 gpm maximum design flow on the tube side.

9) Vapor Extractor a)

Purpose:

Removal of saturated air above the oil in the tank promotes

-evaporation of any water in the oil and reduces moisture condensation and accompanying rust in the system.

b)

Description:

i. A 5 Hp. AC motor driven fan takes suction from top of lube oil tank and exhausts to Turbine Building roof after passing through an oil mist eliminator.

ii. Maintains 1/2 to 1-1/2" H2 0 vacuum.

c) Power .Supply:

4$OV AV turbine building ventilations board IA

13) Bulk Lube Oil Storage and Transfer (P&ID M-4i) a) Lube Oil Purifier

i.

Purpose:

To provide continuous cleanup of the 1u'e cil.

ii.

Description:

&a. One lOO1: systems bb. Rotary gear tyoe lube oil pumps and cenzrifuse type purifier.

cc. Capacity 1000 callons per hour

-0.sOo

'10 :aiicr  :,

ii. Sz.orace 'or i-7edia-:y- avaiIate -- ear. 'ube oil.

c) Dirty Lube Oil Storage Tank

i. 30,000 gallon capacity ii. Storage for spent oil prior to offsite shipment for.

reprocessing or for purifying.

d) Lube Oil Transfer Pump

i.

Purpose:

To transfer oil fromtankto tank within the lube oil system..

ii.

Description:

aa. Two 5 Hp. AC motor driven pumps bb. Dis'charge 100 gpm each iii. Power Supply:

480V AC turbine building ventilation board 1A

e. Control Room Instrumentation Item Device Range t) Bearing Oil Header Pressure indicator 0 - 100 psig

2) Lube Oil Tank Pressure indicator 0 - 100 psia

.3 Shaf- 3eaiing System

a.

Purpose:

To provide sealing for the high-and lov; pressure turbine rotors

-o prevent:

i, Radioactive steam from entering the Turbine Building, and

2)  ?'on-condensables from entering the condenser.

b. Brief

Description:

-r bies.r ar~z -e :-e

. ':re r-

• ":res~jre

. .t i turzine dc -'o -r c-:-acz.in aar,d-.

sseczions e hi:-r :."urbine-_"

~.-FP

- 22

c. Components

1) Steam Seal Regulator Assembly (Figure lA) a) Steam seal feed valve, air operated b) Steam seal bypass feed valve, motor operated c) Steam seal unloading valve, air operated d) Steam seal unloading bypass valve, motor operated operated e)' Steam seal supply from main steam header motor f) Steam seal supply from aux. boiler motor operated g) Relief valves (4) h) Steam seal header

2) Gland Seal Condensers (2) (one Shown)

3) Steam Packing Exhausters (2)

L) Labyrinth-type Turbine Shaft Packing a) Pressure Packing (Figure 12)

i. Pressure Packing (Figure 12)

First leak off is to extraction steam line to the HP ii.

feedwater heaters.

iii. Seal steam header at A psia.

aa. Supplied by steam seal feed valve during startup and at licht loads.

HP br. R1aintainEd at hiah loads oy leak through from unloading valve.

turbine and action cf seal s iv. Gland Seal Exhaust Vent aa. Held at slight vacuum by gland seal exhauster

- 23 -

b) Vacuum Packing (Figure 13)

i. Used on LP turbine only.

ii. Gland seal from seal steam header to reduce air in leakage.

iii. Gland exhaust; vacuum maintained by gland exhauster to remove air in-leakage and seal steam leaking back.

d. Flow Paths (Figure 14) l} .Shutdown to 300 psig Reactor Pressure a) Steam is supplied to the steam seal feed valve from the house auxiliary boiler.

i. An air operated pressure control valve.

ii. Reduces pressure to 4 psig downstream of valve.

iii. Valve fails open on loss of signal or air b) A steam seal bypass feed valve is provided bypassing the steam seal feed valve during low pressure steam supply conditions (<250 psig).

NOTE: The steam seal feed valve is designed for rated pressure operation and therefore will not provide adequate seal steam pressure (A psig) until throttle pressure is

2EC psig.

c) Sealing steam is applied to :he high and low pressure tur bine shaft seals (Figure 12 and 13).

d) A oland exhauster fan provides a vacuum of 5" HWO to the shaft seal to prevent steam leaking into the Turbine Building.

e) -he exhausted mixture of steam, moisture and air is routed to a gland seal condenser to condense all the steam and re-urn the condensate to the main condenser.

f) The gland seal condenser is cooled by the Condensate System.

The non-condensables

7) are routed to the Offgas System for 2_ O.eraEion from 7:0 zsia reactor pressure to low oower zurbine opera-i ons a) Same-as above except sealina steam is from main s:ea- line

3) Hiah Power Operation the exhaust a) As reactor power increases, steam pressure at 0f .he high pressure turoine increases.

its way outward b) Steam from within the turbine now forces the steam to increase past the inner packing and attempts seal header pressure beyond 4 psig.

control valve c) Eventually, the steam seal supply pressure and the for this leakage, completely closes to comoensate to maintain steam seal unloading valve opens as required 4 psig on the header. (Steam unloading valve fails closed

-if diaphragm breaks.)

to the A5, B5, d) The steam seal unloading valve discharges extraction lines (from and C5 low pressure feedwater heater turbine 12th stage).

is provided around the e) A steam seal bypass unloading valve it should fail steam seal unloading valve in the event closed.

the high pressure f) in this mode of operation, steam from low pressure for the shaft seals is the sealing steam turbine section seals.

the relief valve g) Should the pressure control valves fail, Manual pressure.

will maintain seal system at a safe the bypass possible with control .of pressure is then valves.

e. Control Room instrum~enrtation Device Rance "Item indicator 0 - 10 psig

) Steam Seal Header Pressure 0 - 331 H2 0

2) a*rc Exhauster Suction Pressure indicator TURBTi PORTECi

. ,D REACTOR SCRAM INSTRU:OENITATIOi 1OO,

1. Turbine Trips

.. -. ay'. -. r:.r.e vaes

1f 0.c~ec ,_,ce- r.ine _

vaes.

,a) and subsequent clcsin; tri o of the exzrat:-ion relay du'-,, LP for va.'ves a---C,*

o al- conto~led *y it 'See fe-cwa"-

b. Turbine Trips Trip Setpoint Reason for Trip High reactor water To prevent moisture ca.rryover level from the reactor into the tur bine.

Prevent loss of control of the Low EHC control oil turbine.

pressure <1100 psig Low Turbine Trip System Seals in turbine trip.

oil pressure <800 psig

>0.035" Wear greater than this amount High thrust bearing wear is abnormal and is indicative wear of incipient bearing failure.

110% Turbine blading will fail due

- Mechanical overspeed to high centrifugal force if speed is too great.

112% Backup protection for the 110%'

Backup electrical overspeed trip.

overspeed To prevent damage to lasz stag.

High LP exhaust hood 225 F. blading and inner casing due temperature to overheating, overstressing and possible misalignment.

Cool ant Prevents overheatino of the Loss of Stator cooling Pressure generator szator windings.

if cenerator amos >7726

<13 psig OR Cool ant Temoerature

>950C

<105 psig Indicative of failure of .SC.

0o,../ ,Su discharce a broken oil line or loss of

@ >1300 RPM oil supply to X.SOP. Continuec operations could damage the pump or result in a l-ss of all oil.

rCE Z -SUre -- -C--.

luce oil -_- s:-e', . ic -*-,

operation -.oul c -:..Ye sult in wioed main cearings and possible damage to the machine.

Trios SetDoint Reason for Trip Loss of both speed EHC system required at least one speed signal zo be able feedback signals if to control the turbine valves.

turbine >100 RPM Indicative of loss of heat Loss of condenser sink. Turbine is not designed vacuum <19" Hg to operate at low vacuum con ditions. Operations at low pressure may result in heating of turbine blading and a con denser and low pressure turbine overpressure conditions result ing in rupture of the atmos pheric relief diaphragms.

10 mils Prevents damage of turbine High vibration components.

Prevents condensate from back Moisture separator Hi level ing up into the separator and drain tank high level possibly carrying over into the low pressure turbines.

Protects turbine from conse Low bearing oil tank quences of a loss of lube oil.

level Protects turbine from over Generator electrical speeding when load is sudden or main transformer ly removed from generator.

faul ts: 26 devices Senerazor Differential G'

2) Main Transformer Differential or Sudden Pressure

2) Generazor Backup Relay, Field Failure, or Trnasformer Feeder Differential S)

Station Service Transformer Differential , Overcurrent, Sudden Pressure, or Neutral Over-Current Generator Breaker Failure Relay G)

~enerazor Naegative Phase Secuence

" enr-rSra 2 'enerazor Over-Current

Trips Set;oint Reason for Trip Remote electrical For operator use in the event

.rip Pushbutton he detects a potentially dan gerous condition.

Local mechanical For tripping turbine at the trip Lever machine.

2. Generator - Load Reject

a. Definition:

electrical A greater than 40% mismatch between the main generator output and turbine power.

crossover pressure.

Comparison is made between stator amps and turbine

b. Causes of a Load-Reject breakers. (OCB's)

1) Manual opening of main generator output circuit grounded.

2) An "open" in the grid without any lines being result in a generator 0TE: Any automatic trip of the OCB's will trip rather than a generator load reject.

by lst stage pressure)

c. Results of a Load Reject at <30% Power (measured by the fast acting

1) Turbine control valves are tripped closed solenoids. (Reactor does not scram').

to acceot steam that

2) Bypass valves open within their capacity was going to the turbine.

back toward zero load.

3) EHC load selector begins running is <*-:.

Control valves partially re-open when load-mismatchwincage losses.

and machine to continue carrying house lcacs load-reject condition is B) Load selector runback stops when the cleared.

at 1800- RPM due to the

6) EHC system will control turbine speed in E-C ores entation).

EHC s-:e" c*,tr'i netw-'ork. (Discussed of the generator since Z There will DE no volta per cycle trip charge excitation as re joltage reculator will autc-t-rcally quired.

10) This condition should not be maintained for any significant will period since at low loads, the exhaust hood temperature rise and the last stage blades are subject to moisture erosion.

3. Reactor Scrams from the Turbine

a. There are only two scrams originating with the turbine.*

b. 1) Main stop valves <90% full open (bypassed <30% power as measured by Ist stage pressure).

2) Generator-load reject (bypassed <30% power as measured by 1st stage pressure).

b. Main Stop Valves <90% Full Open

1) Scram initiated by valve position limit switches.

2) Anticipates the pressure, neutron and heat flux increase caused by the rapid closure of the turbine stop valves.

3) BADC CABD logic identical to MSIV closures.

c. Generator-Load Reject solenoids

1) Scram initiated by limit switches on the fast acting of the turbine control valves.

flux

2) Anticipates the rapid increase in pressure and neutron the turbine control valves due resulting fr.om fast closure of to a load rejection.

3) Res:onse to load reject Turbine control valves are tripped closed by the fast acting a) solenoids and reactor scrams.

b) All bypass valves open to accept steam that was going to

-ne turbine.

load.

c) EHC load selector beings running back toward zero to carry the d) Turbine will shortly run out of steam necessary heat de house-loads and windage losses as the reactor decay creases.

g a s:raE, "r t _-s

. :res-; .neratE

his szra-m is considered to be

cwer as sensed -vy Ist stage pressure; out razner than :urbine oriented.

H'-'C

e) Control valves will eventually end up full open yet the turbine will coast down.

f) !ssuming that the voltage regulator is still in automatic, the the excitation will be automatically increased to hold rated output voltage.

(volts/

g) The generator will eventually trip on overexcitation cycle trip) to protect the main transformer.

h) The generator trip causes a turbine trip.

4. Control .Room Turbine Protection Monitors

a. Thrust Bearing Wear Detector (Figure 15) 1)

Purpose:

a) To protect turbine internals by tripping the turbine on excessive thrust bearing wear or loss of lube oil bearing header pressure.

b) Detect gradual wear of both thrust bearing plates.

2) Construction:

a) A hydraulically balanced follower piston.

direct b) A pilot valve is attached to the follower piston to oil to and from pressure switches during normal operation.

switches c) A sliding bushing that directs oil to the pressure during tests.

3) Operation:

a constant a) Once initially adjusted the probe tip will maintain

-.:istance from the thrust collar.

i. Oil flows from the bearing header to the top of the and follower piston, through the calibrated orifice out the probe tip to an atmospheric drain.

ii. The follower piston is balanced with half the initial oil pressure on the probe side of the piston.

orifice and rne prCDe tip cil gap.

b) Changing thrust would cause the rotor to move changing the gap between the probe tip and thrust collar. ,

i. This produces a change in oil pressure and unbalances the follower piston.

upon ii. The follower piston moves up or down, dependent moved, to rebalance the oil which direction the shaft pressure across the piston.

iii. Movement of the following piston positions the pilot valve.

is iv. If movement is excessive,.in either direction, oil causing ported from one of two redundant pressure switches a turbine trip.

4) Test of Thrust Bearing Wear labeled a) Accomplished by continuously pushing two pushbuttons Turbine End and Generator End on Panel 7.

gear in b) This energizes a test motor which drives the driven Figure 15.

to its previous c) Allows comparison of thrust collar position position am the same load.

but applies d) Going to "test" defeats the turbine trip circuits to the test motor circuits.

the pressure switch contacts "Test" -oves the sliding bushing in one direction *il until e) Whose ccnlacis is oorted from one of the pressure switches is the stop the test motor. The position of the bushing output indicated in the control room.

remotely f) 3jtput is calibrated in mils ooth locally and previous readings no (control rccm) and can be compared to detect thru.st bearing wear.

b. Vibration Recorder and Detector turbine shafz motion i) Purpose is to measure the magnitude of the in a plane perpendicular to its axis.

.se :uen, zurbine :a*,Se.

vibrazion is excessive: >i0 mils.

Trips turbine if

2) Construction a) One detector per bearing b) A shaft riding detector mounted vertically to the turbine shaft axis:

i. A seismically suspended wound coil in a permanent magnet field provides the output signal.

ii. Output is calibrated in mils.

3) Alarms at 5 mils.

4) Turbine trip at 10 mils, can by bypassed at Turbine Supervisory Instrument cabinet in the Auxiliary Electric Room.

c. Eccentricity Recorder and Detector straight

1) Purpose is to indicate and record the degree of shaft ness (bow).

2) Shares the same recorder as the Vibration Detector.

3) Conistruction:

a) An air gap pickup mounted in the front standard on either side of a steel ring attached to the turbine stub shaft b) Any change in shaft straightness will alternately increase and decrease the air gap between the shaft ring and detectors.

c) The changing air gap increases and decreases the moedance characteristics of the detector which is eleczronically converted to a signal that is displayed on the recorder.

d) Output is calibrated in mils.

o. -*rzine Expansion and Temperature Recorder i' Expansion (Figure 16) heating a) Purpose is to measure shell and rotor expansion wnile contact up to warn the operator of possible metal to metal within the turbine.

ýrfr .ex-: or c-.z tetr~n he r:-::,' ard nz SlEll are To expand an- con-rac-.

,ree The LC snells, ceneratcr stator and thrus: bearing are fixed in place.

c) Recorder points

i. Pt. 1: Shell Expansion, 0- 1.0" toward Upscale on the recorder shows shell expansion the front standard.

ii. Pt. 2: Differential Expansion, 0- 5" is.greater Recorder upscale indicates shell expansion than rotor expansion.

iii. Pt. 3: Rotor Expansion, 0 - 2.0" toward the Recorder upscale sliows rotor expansion is generator.

d) Shell Expansion Detector to a fixed

i. Measures expansion 6f HP shell relative point on the floor at the front standard.

positions an ii. As the shell moves a mechanical linkage changing armature between two opposite facing coils their impedance.

to cor iii. The coil outputs are converted electronically resoond to position; calibrated in inches.

e) Di.fferential Expansion Detector expansion between

i. Purpose is to measure the differential the HP shell and rotor.

ii. !Vounted in the front standard.

of a collar iii. Employs an air gap detector on either side on the turbine rotor.

is supplied, iv. During a plant sTartup as sealing steam than the the rotor tends to heat and expand faster toward zero.

shell and hence recorder indication moves equalize, the

v. As the turbine is rolled and temperature moves toward mid shell expands and recorder indication scale.

vi. 'Normal cold position is mid-scale.

-o Exarnsion 7cr Dezec_:r measures rotor

i. Similar to differential exoansion but rela-ive -to a fixed exoansion toward the cenerator

oi.,-r on the floor.

ii. The detector is an air gap measuring device using a rotor collar at the generator end.

iii. Output is calibrated to read in inches.

H. TURBINE OPERATIONAL

SUMMARY

1. Normal Operations:

Will be covered during the control room phase.

'2. Operating Limitations

a. Conirol Valve Warming Limitations (Figure 17) tem

1) Procedurally limited to curve AT inside to outside metal perature.

rolling the

2) Should be essentially at full temperature prior to turbine to prevent too fast a heatup and possible overstress rolling.

of the metal due to greatly increased steam flow during

b. High Pressure Shell Temperature Differential to preven t Limited to +150 F. z.T inside to outside metal temperatures 0

excessive thermal stress.

and possible To prevent large T's, excessive differential expansion to tempera is not up high vibration on a startup of a turbine that ture, the following restrictions apply:

Classification HP Turbine Temperature Acceleration Iniziai Loading Range Rate Loading Rate Classification r

• up to 250 0 F. 60 RPM/min. 3c' *Hold foi Cold Turbine proceed as in steady state.

3:' Proceed as

';arm Turbine 250 to 350°F 90 RPM-'/mi n. in steady state.

-* R '.,-ir Srreceed as

-.'C - - *: .

Snste%. V 0

-Vcws metal :enerat.re to equalize and exhaust hoods zo coot .o <125 F.

f I

- 34 temp. <200 0 F)

I) If starting up a cold turbine (first stage bowl synchronizing hold unit at near rated speed for one hour before to arid.

c. Steady-state Load Changes (Figure 18) times.

1) Stay within 150 F. AT limitation at all 0

power increases

2) Figure 18 shows time limitations applied for both and decreases. (The curved lines are values for the lowest load involved in the change).

Example No. 1:

and it is If the turbine is at 30% power steady state power increase must desired to increase power to 90%, the be made over 14 minutes.

Example No. 2:

and you If the turbine is at 60-" power, steady state time limi want to increase power to 90.%, there are no tempera tations (as the HP shell is already near maximum ture).

(This is tne normal flow control, load following range of operations.)

Example No. 3:

and you want If the turbine is at 100" power, steady state be made decrease must to decrease power to 40':, the power over a 10 .inute period.

turbine on rate NOTE: There are no restrictions from the oT power change between 60% and 100!; power.

a high pressure feeder

d. ,eazer Out of Service Limitations - Whenever load to 70%.

at heater stri-ng is isolated reduce turbine specific amount'of steam to

1) The turbine is designed to pass a the feedwater heaters to heat the feedwater.

the steam

.o flow through

2) Whenke - heaters

-. rbine are taken

ýo,,-jns t rea- out hrf service, c- I t of ,--

hee:!_ -=,..

ex4-racion lines i.creases.

t.e..

u: ';,out::

Th i increase zhe ;c;:er r c, L,sea by -rne turine and blades downszream, increase the Icading on the diaDnra-cms turbine.

Oarticularly cn -he last stage of zhe

Revision Date BWR SYSTEMS LESSON PLAN

-. t1 .* *.. . i r*'

, I 6 .s ..# i .iA REFERENCES 1.

1. Boiling Water Reactor Systems Manual Chapter 2.7

2. Peach Bottom BWR Discussions 7.6

3. High Pressure Coolant Insertion Pump Turbine Drive Technical Manual (GEK-15545)

4. Browns Ferry Nuclear' Plant Final, Design Report

5. General Electric BWR Thermal Analysis Basis (GETAB) NEDO-l0958

6. Brov.ns Ferry Unit -l'and,-:2 Technical Specifications S. 0O-JECTI','ES ,

• S1. Full'y understand the purposeof-the system and its design objectives.

2. Know major system componentsý,and their:relationship to each other.

3. Lear,. signifiCant'system instrumerntatiOfn, setpoints and interlocks.

Understand automati'c actions in the system..

TecriC:Ai Srec'fications -associated with system.

_. *- .'r.L -E-* 5C TT PT O!

wate r

-a .z _*-u.tne reactor vessel wirh preheated, derinerahi:ed.

-%: rate ecuivalent to the steam generation raze.

6 "13.33 x 10 -/hr. rated feed4.ater flow 7.c' provide an injection oath for:

. -. * - -- ^ *",, )"TI

,'eactor ..ore ISOIa-.iUII £,uuII'I. X~-'

'-ich >essure Coolant iniec-ion-'HD.

• "  :.ter Cleanup 0

2. Components and Flow Path

a. 2-r=n-- (7icure 1 ,*

1) Main Condenser. Hotwell (3)

2) Condensate Pumps (3)

3) Steam Jet Air Ejector (SJAE) Condensers (2)

4) Gland Seal Exhauster Condenser (1)

5) Off-Gas Condenser (1)

6) Filter/Demineralizers (9)

7) Condensate Booster Pumps (3)

8) Low Pressure Feedwater Heater Strings (3) a) Drain Coolers b) A, B, C, Heaters (5, 4, 3)

9) Reactor Feedwater Pumps (3)

10) Start-Up Bypass Valve (11 1l) High Pressure Feedwater Heater Strings (3)

12) Fee:water Scarters A)

-w*:ers in parentneses indic:ae number of eac. ... ren.

b. Condensame Flcw Path (Figure I) 11 Main condenser hotwell orovides NPSH for condensa:e ;u.ps.

2) Makeup to hotwell provided by the Condensaze So:-ge Tank (CST).

3) Tao offs on the condensate ounD discharge commonline provide for turbine exhaust hood sprays.

" C*c-ensae nex- flows znrougn the tube sie o0:

a) Both-Steam'Jet-AirEjector (SJAE) Condensers

1 he Gland Sea! Wxauster COr-.Er-se (1) Equipped with an air operated flow controlled

- * --bypass valve; c) The Off Gas Condenser V5) nCondensate then passesinto the, condensate filter/deminer alizers a) .8Wdemineralizersirequired for 100 flow b) Bypass valve can'handle 33%

,(l)~ Auto-opens if 0P-across any filter >45 psid

6) Excess water in the condenser is rejected to the CST just downstream-of the demineralizer.

7)- A tap off-just.down-stream of-the 'demineralizers provides a backup means of pressurizing the gland seal system.

a). Normal suoply is from the Gland Seal System Hea

-Tank b) Details-of the Gland Seal.System are prcvided in the Condenser and Circulating ,ater Lesson Plan.

2) ,cndensate booster -ures increase the system pressure to zrcvide "h to the reactor feec zuJ.s.

9) 'Tap-offs after Vhe-ooster pump provide:

"01 lecirculation'to Main Condenser (1 Provides minimum-flow required for the S.VE condenser to operate efficiently.

(2) Also provides minimum flow requirement for condensate and booster pumps.

(V -'llows-cler.nuo of condense- vci.-e befcre operating (short cycle).

,- S.-actoiine -e Ye iee- a...

._O;S.

n .=s7=*

leac-tor feed* wa-er pum,, seal water flow.

10) '.'ain flow path aoes through tube side of 3 parallel strings of low pressure feedwater heaters.

c. FeecG.,ater Flow ?azh (Figure 1)

1) Reactor feed pumps take a suction from the discharge of the low pressure feedwater heaters.

2) Each feed pump discharge can be pumped through a motor operated discharge valve or recirculated back to the main condenser.

3) *The feed pumps can be bypassed during periods of low reactor pressure (startup) which is not sufficient to run the reactor feed pump turbine.

a) Startup bypass valve can be automatically controlled by reactor level.

-) The high Dressure heaters are next.

a) 3 strings of two heaters arranged in parallel.

b) Flow is through tube side.

c) A "Long Cycle" Recirculaticn Valve on the cown stream side of each high pressure heater allows filling and venting during startuo.

"51 Feed flcw now splits into two lines before penetra:-ing co.nal r.-ent.

-ac, line has 2 cnecK v=aves. The check valves ac- as

ri-ary containment isoiation valves.

- .e "'line contains a tap-in from the cleanuo system ret-rn line and tne RCiCtnein-ec-ion line. 7he ine tap-in from

-zn=ins'a .-PC. injection Vne.

a)  :-oth lines have thermal sleeves to minnimze stress.

£) Once inside containment. each line solits acain into 3 lines, before penetrating the vessel to supply 5 se_;ara=te ee':ate rs soar:ers.

- ~ P7 S..... " -en '" -CC "S 'i L:jre 3

a. Purpose I) Collects Condensate from "a) Main Turbine Exhaust Steam -'

• b) Bypass Valve Exhaust Steam c) Reactor Feed Pump-ExhaustfSteam*

d), Various Dra'in' LCines- such -as:

(1) Main Steam Lines (2) RCIC Steam Line

,(3) HPCI Steam Line (4) Steam Jet Air Ejector Condenser f(5) Gland Exhauster Condenser (6) Off Gas 'Condenser (7)' Gland Seal System (8) etc.

2) Retains condensate for about 2 minutes to allow decay of 6 ).

short lived-activity (Nl 3' ?rovides NJPSH for ccndensate c ,m.ps.

a) Capacity 3 minutes of full power operation

b. Construction -: "

i) Locatec at zhe bottom of each condenser snell

2) incorporates--reheating and deaerating features

-a) FMost de"ration 6ccurs in'tube bundles but lower Sbcndle and hotwel1 further deaerate I ong`.tudirnaily diviced into 'vc, seczions- ri.n

'ccl lection trays.

"' ,eh.ea-.Z S coils 6eiow col ecticn :rav

a) Provide dearate steam at low steam flows from main steam system.

Pipes distribute portions of exhaust szeam to :elow collection trays during high steam flows.

6) All three hotwells interconnected by 30" crossover pipe for pressure and level equalizing.

7) Each hotwell has a separate condensate outlet to a common suction header for all condensate pumps.

c. Op&ration

1) Steam Flow Path a) Steam exhausting from the low pressure turbine flows over condensing tubes and is condensed by the circula ting water flowing through the condenser tubes.

b) The condensate formed by the steam condensation collects in the collecting trays of the hotwell.

c) Portions of the tu-bine shaft exhaust steam are routed by ducting to an area below the collectioi trays where it is disbursed to flow out through holes in the collection trays and be condensed.

1) This is called reheat steam.

', :earaL,*n a) The coilectinQ trays nave holes tnrcugh whicn :on densate flows to tne condensate pumP suction port.

This type of flow zents to atomize the condensate increasino its surface area fcr hea- transfer.

b) -ne reneat steam *frc. above discussion) flowing u:

through the collection tray strikes the downward flowinc condensate flashing the condensaze to steam and liberate noncondensables to the condenser air removable system. The reheat stea-, is concensed in the process.

1 bring low steam flow conditions (szartuo) steam from,

re .-,ain szeam heacer :an be ad-i:zed :- the reheaz

. 1:'

Z2 -0 1' - - - ": O- -. I

-7

3) Condensate Flow Path

-- r z

=round baffle plates before reaching the concensate pump suction lines.

(1)Provides deJ minute holdup time to allow for decay of N' (2) Provides storage space for 90,000 gallons of water, -at*a normal level of 27".

4) LevelControl -

• a Makeup .. .

(1) Normal through 114" level control valves from

'CST.

n-(a) Valve controlled by level indicating coi troller normally set to open valve when in level falls about 6", from normal ('-21" hotwel I).

(2) Emergency-makeup from CST through 10" motor operated level control valve.

"(a) Operator manually controls valve frorm control room.

(3: Low level alar "15" in hctweil.

3) Reject "a) -4orrmal-throuch 114 level control valve to CST

',I)Valve cont'olled by lievel indicazing conzrollers set to open-valve when level rises about 6" from normal (-.33" in hotwell) b) Emergency reject to CST through 10" Motor oDerated level control 'ialve.

"room.

eve: r' 3'

d) Condensate oumps provide driving force for reject.

prior to returning to CST.

(1) Eliminates impurities from leakage of condenser tubes during shutdown periods.

2. Condensate Pumps

a. Three Condensate Pumping Units

1) *Each unit consists of one condensate pump and motor.

a) Each motor is 900 hp., 3 phase,,60 Hertz, 4160 volt induction motor with a speed of 1800 RPM.

b) Power supplies are from unit Boards IA, 1B, and IC respectively for pumps 1A, 1B, and 1C.

2) Each pump is rated at -5.4 x 106/hr. (330; of rated flow, 10,830 GPM).

a) The above ratings are based on normal operations, runout ratings allow two pumps in runout to supply 92& of rated plant condensate flow.

3) The only pump trips or electric interlocks associated with condensate pumps are electrical fault trips.

"11 Ru'-s have mecrarical seals with sea! water beinc swncliec

-,-r tne pLMp discharge ba:Lec ap 0y the gland Sea! zan,.

5) &.1 WumD bearings are water lubricated while the drive motor has its own oil reservoirs for the motor tnrust and Icurna bearincs.

a) Pump mo:or jacket is cooled by Raw Cooling Water.

3. Steam Jet Air Ejeczor Condensers

a. Each condenser is sized to pass rated condensate flow for air ejector requirements through the tube side.

b. Only one condenser is necessary for full power operation.

1-) Both normally valved in because of the automatic start features associated with the Standby Air Ejectors.

c. -.e, s%-.e rans go : oncea:E cra'n tark .ia 'cc, se--s.

4. Gland Seal Steam Condenser

a. condenses steam from the gland seal steam s ystem.

-b. Shellside of condenser~maintained at slight negative pressure by steam packing exhauster.. -. .

c. Drains go to condensate drain tank via:loop seal.

5. Off-Gas Condenser . *-

a. Cools0 superheated discharge of the recombiner from o*800OF to

<1 30 F.

b. Shell side drains go to condensate drain tank via loop seal.

6. Heat Exchanger Flow Balancing Valve

a. SJAE Condensers, Gland Seal Steam Condenser, and Offgas Condenser are all in parallel condensate flow paths.

b. Each of thne above heat exchangers presents a different resistance to flow with a corresponding probability that the heat exchafger with the least resistance during periods of low flow-would rob the remaining heat exchangers.

c. G'.and Ze_, Ccn-enser orese nts .,os- n.ioinaflew restricticn.

d. -low blancingvalve auto control,fiow through valve based tc excess..ofthat required-for-Gland Seal Condenser.

1 Assures most limiting cor.ponent has sufficient flow.

2, Air Operated Valve .ormally Run in-Auto

3) Controller is Local

7. Condensate Filter/Demineralizers Sa.->.Maintains purity of the reactor feedwazer by removing disso"vec

""and susz.ended-solids which resul: from co-rosion in the con

.a.. e"  :, -_re mair, ccncenser.

1) Reduces damage to components due to chemical and corrosive attack.

7' :ýeducs the fouiing of hear transfer ur, =s_

3) Reduces impuri.ties available for activation.

Al) Reduces the consequences of condenser tube leaks.

b. In order to meet these requirements, condensate filter/

demineralizer effluents will be maintained within the following specifications:

Lbading Effluent Total Dissolved Solids <.l..mho/cm*

(Conductivity) pH at 250C <6-8*

Suspended Solids <5 ppb Total Iron <5 ppb Total-Copper <2 ppb Dissolved Silica <5 ppb Chlorides <10 ppb*

l) Conductivity is measured since it is a very good indicator or most imourities.

2) '.etallic impurities are Vimitea to prevent excessi e Dlating out on the fuel cladding surfaces and to reduce the amount of activation products.

1' Silicate (SiO,) is maintained z5 ppb because it 'ini carry over inr.zne main steam sYstem and pla:e cu: :n the turbine bladinc.

- iimts in this table are based on Fil-er/Demin. caoacizy anc are

-=_-_ ~on a saole at the -ilter/Demin. e-luenz. items wi-h :he asterisks

--. e , -d later.

- 11 -

4) Chlorides are maintained low enough to limit the possi bility of chloride stress corrosion.

A) eI' Dnb chl ,iorides are very dif-icul- -c -e-ure.

therefore chlorites out of the con*ensa-e cem.ineralizer are maintained low enough to keep reactor water chlorides from exceeding their specification.

"c. Nine full flow condensate polishing filter/demineralizers known as Powdex (a Graver Corp. Trade Name) are connected in parallel are used as ion'exchange mediums and filtering agents (Figure 3).

.J) Eight are required for full flow operation, the ninth beina ,standby- unit.

'- 2) Each-filter/Demineralizer is:

a) 196' diameter 6'6" high b) 302 woven nylon filter elements (septums) representing 800 ft 2 of filter area (I) Elemernts replaceable through manhole on top (2) 'Elements supported by vertical rods c) Flow enters shell at bottom, flows through septums with filter' demin acent on them, and exits through lower tube sheet to unit outlet.

0 C.,, Desicn pressure 700 Dsi a: 15 F

-,* zFlter/iemineralizer -Ace' a) Graver~product-called powdex

'I! Powdered cation and anion exchance resin in.

nydrogen ano nydrcxyi form (2) 'Uniformly coated by orecoat system to 1/4" on septums

'(3) Serves dual function as filtering and demineralizing aacent'

( 'on-recenerable enc .-nen exjancec N' ', is ::_rocesseC

-A ,r---C;-E--- 1S------S-

- 12 -

b) Solka-fIloc I. Gra'.'er Corp.. .ae -or ce!iu!cs `-i er F -r ing agent.

(2) Only used on a few units during reactor startuD to remove large amount of suspended solids.

c) Resin Expiration (1) Conductivity at effluent >l,,mho/cm (a) Conductivity cells at inlet and effluent of system monitor efficiency of all units each has an effluent conductivity cell.

Each cond. cell has the following alarms.

i. Hi conductivity any vessel effluent

.3 micro mho local ii. Hi conductivity system effluent .3 micro mho local iii. Hi conductivity system effluent .5 micro mho local iv. Any local alarm causes cond. demin.

alarm in control room.

"(b) :nica-es ion exc-,ance :acaci:v liii:e

-ny n, ,,1ter.'demin. witn a 2E -sid pressure orcc.

(a) Hi-h -P indicates restriction zo flow caused yv 4ilterinc process and reDresents a potential 73r se_**um ca.a.e.

"i. *laron system -P -'0 .sid local. and control room.

ii. A system -P >45 psid auto ooens,derin.

bypass valve whicn will orcvice 1/3 of rated condensate flow.

'" -prox-azeiv a -week cvc!e.

=s

(1) Each unit 'eqUipped ýwith 'a 60 GPMN holdinr u.-.,D.

2,n

• i '*' - un*

o,-,c*' 'r.,'- d r,:. -s _o V0 G2r, to maintain flcw tnrouch uniz ano 1 from failing off prevent filter/demin.-acent septums.-'-"

(a) If coat on septums not maintained it must be re-established-prior to unit use to prevent demin./filter agent from being pumped'to reactor-vessel.

..(3) Local alarm pump failure if unit flow drops to 45 GPM,

" e) 'Precoat and Backwash System F -

(1) Precoat necessary to establish filter/demin.

agent t6-,1/4" onseptums prior to unit use.

(2) Precoat System'Pump and Tank Arrangement (a) 'Pump 5 slurry of powdex resin to units from precoat-tank -at 1185 GPM and 100OF

':conditions.

(b)-'Tanks .(2)-- 54" diameter 60" high mixes "resins-with 1/2 HP mixer (3) Backwash-systemrair and condensate mixture to flush seen: oowdex to backwash -eceive-r. --an in radwas-e.

() Back%:*ashihg and precoating are all automatic one-unitfis placed out of service ano the back

-wash/reccat process 's selected locally.

'-a) Holdirc pump w'ill auto hold the ;recoaz until unit is valved-back in.

) Resin Trap (Figurec4) a) -Strainer in unit -effluent lines serves as resin trap

,-- rCatches particulates tha- -ic.z iash tnroucn if seotum

- c, - -a rossed strAiner -.E r,-ireC and aIarmed hich i ccntrci room. "

- 14 -

d. Flow Balancing System (Figure d) 11 Each fiiler/de.in. should carry ecuai 'icw .

2) Each filter/demin. unit presents different flow restrictio6 because the condition of their resin charges vary - i.e.,

they were rek'newed at different time intervals

3) Equipment The equipment which comprises the flow balancing system consists of the following items.

a) (Indicating flow'controller (complete with pneumatic transmitter and orifice plate) for each Powdex vessel.

The controllers have pneumatically adjustable setpoint and proportional-plus-reset mode of pneumatic control.

b) Control valve at the outlet of each Powdex unit. This valve is positioned by the signal from its respective flow controller.

c) A combination of high-signal selector relays connected so that the final output is that flow controller outout which has the highest flow.

d) The master indicating controller - this controller has a manually-adjusted setpoint and proportional-plus reset mode of pneumatic control. It measures the flow signal at the output of the high-signal selector relays.

This is ir.dication of valve positicn for tne ccntrol valve whicn is widest o:-en. The master ccnz..-:. er maintains the set degree of valve opening ny simultan eously aajusting the idertical setpoints of the flow controllers. in actual fact, the master controller is controlling -he output flew of that vessel flcw con troller with tVe greatest out*ut.

4) Method of Operation a) The master controller should have its control point set for the widest valve ovening which is consistent with allowing the valve to maintain flow control. 80 zercent ovening accears to be a good star:-ng .oi'nt.

Dernaps greater opening will be possible 00i-h good control. N" tne flcw controller with greazes- u:.-ut a ower senc'.nz snould ce used for the -as.e: c:n

-ro ler.-

- 15 -

b) With two or morePowdexvessels in service, the one with the greatest loss of filtered matter on its element "will-recuire he ceatest cecree of control valve c:eenrnr. OCher ?c,wzex-uri~s will have .ne-r cuet valves open to a lesser degree to obtain the same flow iate.

c) The combination~of high-signal selector relays transmit to the master controller the signal which indicates the

"-signal level f 'the vessel flow controller with the highest output flow.

S--fIf'this -signal 'is-below the setpoint of the master con troller, the'ojtput of the master controller will increase. -This'output is connected as the setpoint signal of all the flow controllers for the Powdex vessels

'in'service. Increasing the setpoint of the flow con

-trollers'dauses'their output flows to rise.

The over-all effect of the aforementioned action is to have the most exhaustec powdex vessel with its control "valve opened to the amount set upon the master controller,

-'and the control Valves'for the less exhausted vessels throttled closed-to-some'extent, to maintain an e-ual flow through all-the-vessels which are on stream.

d) Aswill be explained later.; sometines the initial chance

'ol vessel flow controller' output is in the direction oopositd to that called for by the plant load change.

It is thd function of the master controller to react

as:er to the flcw con-roile- to react -asze, to the

w c ---

I o;" conzroller out:'t CnZ_ .r....o... ha r, ac-s to modify valve pcsi&ns. The r,e: eifecz is to "rmodify flow controller setocint to agree with the plant load, with necligible 6hance of valve position.

The best conzroilernmode settincs can be esta'Iisherl nly thr~uch o ex-erience.

'eratino Usually.

"Graver Powoexsystems are eouipped with flow balancing.

the controllers are started-with the following se-.tingst

-. 4-Prooortional Band -I00":

Reset - 0.!-minutes per repea-t, 7 ow r'..r*on1ers :

- 16 -

b) Plant Flow Decrease

.hen olant flow rate decreases, the vessel flow goes o., :ne setpoint. Wr.is caues :ne oegirn nnc cf an increase in controller output w.hich is sensed by the master controller, which decreases its output to lower the setpoint of the vessel flow controllers to restore the desired output signal.

c) Increases Solids on Filter Elements As the Powdex vessels progress through their service runs, the coating on the elements will provide in creasing resistance to flow.- This is a gradual, but unavoidable change.

For those vessels which. are not the most exhausted, an increase in element resistance will cause the flow controllers to open the control valve enough to main tain flow at the setpoint.

Usually, it is the most exhausted vessel where the element resistance is building up the fastest. The control valve of this vessel is open wide as the flow balancing system allows. Therefore, the overall ores sure Toss from inlet header to outlet header will gradually increase. The plant feedwater control makes up for this, by performing the necessary action in the direction of increasing flcw to counteract the increase of pressure loss across the Powdex systems. The result of these actions in the direction of flow increase (see secvicn 5) al). abo'e) is Ina th:e ccn:rol valves V less-exnausted vessels wii tnrottie slighztv in order to T-aintain balance of flow with the most-exhausted vessel.

The overall increase of pressure loss Ohrougn the Tcswdex system is lirimed si-ol' by placing cn zne stream a freshly preccated vessel which has oeen standinc by. Some systems allow partial ocening of a bypass (see specific instructions for your inszal lation). The exhausten vessel is then removed frcm service for re-coating, after which it is usually olaced on standby.

2. Coneensate -ocs-er Dumos (Figure !;

a. '.-:s Drcvis "MH for Reac:cr Feecwa.-er .*rs

. -.- Dump recirc.valv*Ie control ied automatically by flow oster controller at the discharge of the condensate pump.

I) Acts as minimum flow vaive for; conae nsa:e pLps, con "densate-booster pumps, SJAE-condensers, off gas condenser, and gland exhauster condenser.

c. 'Motr

-1) 1750 horsepower, 4160 volt, 60 cycle, 3 phase a) Pump 1A from 4160 V unit Board IA b) Pump IB from 4160 V unit Board I1 c) Pump IC from 4160 V unit Board 1C

2) 'Journal Bearing Aa Force feed lubricazed by Booster pumo auxiliary oil system .

"3) Pump Trips "a) Eiectrical fault' b)

• rczion pressure<E-psig decreasing .for-5 seconas

,i) Alarm at <15 psig decreasing r Ierng lube oil pressure <10 *si_- cecre=sir., f7Zr

.: <7 psi 9 alarm and auto start (if associ-ae:

booster pump running) of-auxiliarv oil our:

(a) -Auxiliary-oil pu-.o should res-ore zearing lube oil *,-*,sure :o creater 7-an - 0 .-- I before 5'-second .time delay nas ex:irec.

) Pump Start"InteiockS'- -

a) Pump cafi be started or stopped locally (with push 1,utl:ons) or re:note in zne control roc7..

4; ,,tncne, soitzh in'-.azes a

""- - T-'z

- 18 -

(1) Auxiliary oil pump auto starts during the 25 seconds if not all ready running.

(2) if auxi iari oil cur, *s r.nnnc,- r.et z seconr timer. is bypassed and the booster pump will auto start in 15 seconds if:

(a) Condensate booster pump suction pressure is

>10 psig and; (b) Booster pump bearing oil pressure is >7 psig.

d. Pumps

1) Centrifugal, 10,800 GPM/per pump, at 450 psig

2) 3 pumps are normally required for 100% operation, however, the pumps are rated such that 2 pumps at run out conditions will provide 92% condensate flow.

"3)  ;.'echanical Seals

a. Supolied by Running Pump A*) Radial and. Thrust Bearing Force Feed Lubricated

e. Lubrication System - each condensate booster pump has its own lubricating oil system consisting of:

1) An Attached Main Oil Pump Z\ 'entrif-."a, p*.c pressure -.

praC~e 25 osi

2) A" "?,Z Welectric motor driven cen-rifugal auxiliary oil a) /ischarre Pressure %-25 psig b) rup Starts (1) Manual from local start stop switches (2) Automatically if:

(a) The associated ccnoensate bccster pumo is running and bcoster pump nearinc oil

-- i9 -

"(b) *The associated condensate booster pump is started .or, Si. ,ime'deiay a~iows auxiliary oil

'pump:to'develop bearing oil pressure before condensate booster pump starts (c) Any condensate pump is started and there C are'no condensate booster pumps running

-)- Pump Stops

.(1) Manual from Local Stop Switches 3),'15 gallon Oil'Reservoirr

4) Oil Cooler a) 'ReqOires-Raw-Cooling Water

9. Feedwaer Heaters and Drains

a. :urpose "1)"Improves overall plantefficiency factor.

2) Provides path for moisture removal from turbine stages.

"3 Three strings (A, B, and C) keeps tube velocity within lim'its and provides reasonable beater size.

"-:- s.u ru c t oin

-!) "-V" Low Pressure'(LP) Heaters (Ficure 5) a) Horizcnt-.-I U-tube heat exchancer with intecral drain cooler secti on (1) Drain cooler Drovides two functions:

(a) Raises feedwater temperature so less

-. - "

• extraction steam required.

,D) Lowers (subcccl--s crairs to -reven:

flashing in transit zo next neater.

- -*a '-cc-:e -. nSice rCK r- . .. rc-

• et] *ee

-. *b.*

a) , cr -'ai* Is.

eec;aterr ow -ath

(1) Feedwater enters at the bottom of the hea-er, into a ,rater box.

(,-)

2 .rivi-er plate fsrces the feec.ater i.nzo tie stainless steel U-tubes.

(3) After'passing through the tube sheet, the feed water is first heated by the drain cooling section, cooling the drains.

(4) Upon leaving the drain cooler zone, the feedwater acts as a condensing mechanism for the extraction steam.

(5) Returning through the tube sheet, the feedwater exits at the top of the heater and flows into the "3" heater.

(6) Feedwater outlet temperature is --239°F at full povier.

c) Extraction Steam Flow Path (Figure 7)

(1) "4" heater extraction steam is taken from the tenth stace of the L.P. turbine and passes into the heater throuch two ifnlet ports '2" szear.

lines).

(a) 1oisture from the turbine is carried ,qith the extraction steam.

,-'-he are areate~sccnzinz - :n the turbine is running as :-,e only v-alves in the extraction lines are mechanical :beCK valves which prevent reverse flow.

. -oince-en: plates deflect the steam as it enzers.

7:rc .:g r:.e s tea .*; o fio.oa out an* ccr.n over .nhe coolin: water tubes where it is condense. trans fe-rirc its heat t:o the feedwater.

(3) The condensed stean joins with the other e<traction drains. flowing zoward tne drain cooler seczion.

d)  :,rain -,ow Path (Figure-:

• .e~d :

• I*'.- -, - - ,'e

---

-e_.: -  :*.r . - :r d of the drai.s c:~eo':h dais-ýsh a -:ý=" ene as enter neend. ':

-=

J

- 21 (2) Condensed extraction steam joins the drains.

t,

aen tne cctr3ned drains re7

h nE :-ran 5 c ;er section,-they are-sucked up into tne cooler by a siphoning action, flow around a series of baffles and exit through the.drains outlet to the flash tank.2 (4) The'level of drains inside the heater is normally maintained by controlling the amount of drain flow to the'flash tank.

-(5):-The drain cooler section is completely filled with drains,'acting as a water-to-water heat exchanger.

e) Air, together with fission products and other non-con

-desnible-gases, enters with the extraction steaer and cascaded drains.

(i)- If these gases are not removed, increased corrosion could result-..The heaters could also become air bound, decreasing heater efficiency.

(2) Removal-of. these non-condensibles is accomolished by air vent lines.

%a) Orificed vent lines provide continuous degassing to the main condenser.

Nc

• cminal hezt eyc~ancer S.ne'l side Dressure 2.7 psia.

2) "3' Lcw Pressure Heaters

--' *--:-iaily-the-sme as "'" heaters with the follc'-."nc e'ceotions:

-. 'I (Figure S)ccme Heater:drains

-into ,*," frcm "2" heaters and flow heaters.

(2) Extraction steam comes from the 8th stage of zne

"-LP (Ficure .)-turbine.

(a TTherefore.- the " heaters ooerate at a

"'-ferent t--,.--,re 'd :--eSrE t, c! ,a-c.~er  :.:- e-oeraz-re to =

ii. Nominal heat exchancer shell side Dressure -.69.4 Dsi, (b) Valves in Exzraczion Line

i. Air operated extraction nonreturn line auto shuts on all turbine trips ii. Motor operated extraction nonreturn line auto closes of cp heater string condensate iso. valves close.

(3) Heat exchangers locatedAheater bay of turbine building outside of main condenser shell

3) "2" High Pressure Heaters (Figure 6) a) Vertical, U-tube heat exchanger with integral drain cooler section.

(1) Drain cooler Drovides same function as in "4' heater.

(2) Vertical heater installed due to space limitations and tube removal caoability.

(3) Located in Heater Bay of Turbir.m Buildin.

b) Feedwater Flow Path

1) Feedwater enters :ne boztom of t'.e he;.  :,a:ce, and flows upwar-.

.. rc.sh the tube sice -ne drain cooler secticn.

'2, Passing out of the drain cooler. -ne =eed;.;Iater acts as a condensina -iechanism for ex:r--:-ion steam.

(3) Returning through the zube sheet, feedwater exits at the bott.om of tne heater into tne feec'ater return header.

"') Feedwater outlet zemperature -.3300° at fuli power.

c) Extraction Stear Flow '-ath (Figure 7)

"-.23 -

(1) Extraction steam and moisture from the L.P.

turbine-seventh stage enters the heater at the bozzo- and flcvws Up.ear" vi-' :

-(2) Tube ,support plates direct steam onto the cooling water tubes.

(3)-. Condensed steam-flows down the condensate lane

-. *and mixes with-the moisture separator drains and the drains from the #1 heater drain cooler.

"(4)'-Valvesin Extraction Line

- --.(a) LAir operated extraction nonreturn line

-auto shut on all turbine trips (b) Motor 4operated~extraction nonreturn line auto close if L.P. heater string condensate isolation valves close.

d) Drain Flow Path (Figure 8)

(1) Drains from the moisture separator drain tank and from the =1 heater drain cooler enter

through the drains inlet nozzle and mix with Ithe extraction co6dens-ate.

(2) -This -mixture then flows downward and into a

-drain cooler section.

(3*) Baffles-in the drain coo'er fcrc -.he crains to-take a circuizous rcuze to zne crairs cuzlez.

.(;)

-- -"2"-heater drains cascade into the "3" heaters Al) level control- system maintains the drain cooler full by controlling tnse amount of drain ficw to the "3' neater.

e) Air and non-condensibles are removed by vent Llnes.

.() Nominal,,heai.exchanger shell side pressure -.ll psia reG Le.,

-2" 'I" '-ich Pressure e e-,_e-.

- aŽ- -sseit~a~ll h sa~e~as "2'.' he-ze~s wi-n wne -'cw'..irc

- 94 (1) There are no drains coming into these heat exchangers from a higher pressure heater.

(2) Extraction steam comes from cross around steam-to the moisture separators.

(a) Therefore, the "I" heaters operate at a different temperature and pressure than the "2" heaters.

i. Feedwater exit temperature to the vessel -. 377 0 F (100%l power) ii. Nominal heat exchanger shell side pressure -. 200 psia

5) "5" Low Pressure Heaters a) Essentially the same as A1heaters with the following exceptions:

(1) There are no heater drains cascading into the "5" heaters.

(2) Extraction steam is taken from the twielfth stage of the L.P. turbine.

(a) Therefore, the "5" heater operates at lower temperatures and pressures.

(3) The '5" hea:-e doces not have an integral drain cooler. .-n ex-ernai .drain cooler Drcices t-is function. An internal drain cooler would have made the "5" heaters tco big.

(A) The "5" heaters are ahways in service i-" -he turbine is ooera:ing. There are no extraction val ves.

(5) Since there are no cascading drains into the "5" heaters, the only drains are condensed extraction steam. These drains, along with uncondensed extraction steam, are pioed to the flash "ark.

7;-a 1. ,.,,-ate _="es&a4,.t cco e"s are rus Mnsice :,,e neck* :neSa:O;a:e

-nz-.ý -.C) -~

snace an~d rin-imze :;ioinc runs.

(7) Feedwater outlet termperature 183 F at full power.

- ~,) *o,.nai heat eAchancer shell side pres-urp.

3) Flash Tank Operation (Figure 8)

"a)All *heater drainsIare combined in the flash tank and flowintothe drain cooler.

Any.drains

_,b) -- 'from which flash and any uncondensed steam the "5" heaters is routed back to the "5" heater.

"c) "The'drain'cooler is a water-to-water heat exchanger which increases the temperature of the feedwater.

0 at full power.

Feedwater inlet iemperature is`-003 F 0 F at full power.

Feedwater outlet temperature .is -,130

c. Operation of Heaters and Drains

"- Heater condensate'drains flow from'the highest pressure heaters towards the lowest pressure heaters, achieving a cascading effect (Figure 8).

2) "Condcens'ate "drai'ned from the moisture separator drain tanks is routed to the shell side of heater "2" by a separator

-drain. tank level controller and moisture separator drain

. pumps.. Codensatefrom'heater "'" is also airected to heater "2"-level controlle'r.

2 The level controller fer heateer "2" drains condensate 1o heat%..er Y'". leve', conzroller fPr hea-er "' tra'ns czrcer sate to heater-*" anl,e-e! controller for neater drains condensate to the flash tank.

-) Steam flashincg from the cOshdeniate side drained into the

-Elash tank is routed to the sheI of neater

=-o -ne

" 7- flasn'zank, level :cnzroller drains condensate "The

-main notwdell byway of the "E" heater external drain

- cooler.  :

one E) Extraction ste-am is recuired to force the --rains fron "heater to the next..

-rsa ti'sfactory perfo'rmance cf feedwazer ,eaters. the i) tre level is too nign. heater effici-nC'/ 0di.

if cec,,ease anc concersate 7ýa- tacK u' n tv, -=rnine.

b) If the level is too low, proper subcooiing of the drains is lost.

(1) This causes flashing in the drain line to the dcwns-tream heater.

(a) Water hammer-in the drain line and level oscillators in-the downstream heater results.

'Note: Flashina of'drains will occur normally, but only after passing through the level control valve, where pressure is reduced.

8) Heater Level Control.

a) The "3" heater arrangement is typical of the level control system.

b) Drains from the upstream "2" heater flow through a level control valve (LCV) into the "3" heater.

(1) This LCV is controlled by an air signal from, the "2" heater level control system.

(2) if the "2" heater level changes, the LC7 is opened to pass rmore or less condensate flow to maintain "2" heater level.

(3) Since "2" heater drains will flash a~ter -assing throuah :*e Oe. -he valve is Isc-=ted ve,, close Mo the '3" neater.

c) "3" heater drains flow through the "3" heater level control valve into the "I" heater.

.This L'V is ccnzrlied by an air sional fr-.

.he "3" heater level control system,.

%2) Level changes in the "3" heater are compensazed by opening or closing the LCV.

ý3) An emergency drain valve is provided in the event ..ore dr=-n caoacity is needed on :re drains from heaters 2, 4, the drain cooler.

and '-.re o*-'t-, seý,=arazn:r drz.*, t'Lz.

- 27 -

d). As an example of heater level control operation, assumea 'level 'increase in "2" heater.

"27 he*er LC" would open tc decrease the "level: -

(2) 'Iflevel continued to increase, M2" heaterr

...... ' emergency drain valve-would begin to open

"' '- (3) "If'ltvel reaRche the-high level switch setpoint', "th'e'feedwater inlet and outlet

.valve of the affected high pressure feed

. W. ater-string would close to isolate the leak.--f

-(a)' C16sing the high pressure feedwater string isolation valves from the feed water-system causes the affected 1 and 2 heater motor operated extraction non retuhn valves-to close isolating steam "from-the affected:heater (See Systems Manual-Fig6re 2.7-2 for Extraction Valves).

(C b) Thel'reiponse-to 'increasing level in heater "1" is much the same as heater "2" with the exceptibn of the fact that heater "I" has no emergency drain valve.

"(4)- The ednd result is':

(a) "l"'and "2"'heater motor operated extraction

-nonreturn valve is cIosed and heater 2" eAxraction t--ass is coe (hea:ze "I" has no extraction bypassnvalve).

(b) M2" heater LCV is full open.

(c) All "2" heater drains -low into main :on "denser vialemergency drain valve ;r ;o

.3 heater via LCV.

(d) Since one high pressure heater is isolated, the fee'd~,aer o:emDerature leaving thaz heater'string will be icwered.

281 (e) The inlet feedwater temoerature to the vessel will also be slightly lower.

(f) Feedwa:er flow in one unaffecteC hign pres sure feedwater heaters will increase when the isolation occurs.. This produces a larger At between feedwater temperature and extrac tion steam temperature, increasing the heat transfer across the remaining high pressure

- -heater tubes.

_-(g) The remaining high pressure heaters will "work" harder (require more extraction steam) partially compensating for the loss of the high pressure heater string.

9) Remaining Level Control Features a) Increasing level responses in heaters "3" and "4" are-similar to 1 and 2 except the high level response isolates the affected low pressure feed water string to cause an isolation of the string and the heater "3" motor operated extraction nonreturn valves.

(1) There are no controllable extraction nonreturn valves on heaters "A" and "5".

(2) Heater "3" has no emergency drain valve.

b) Heater "5" affects its level control through the flash tank level ccnzrollers.

c/ Flash tank level control af-e:os a normal ar,* _e.

gency drain from the drain cooler.

d) Moisture separator drain tank nich level effects:

(1) Level control valve to '2 heater first (2) Emergency crain to main condenser second (3) Turbine trio and air operated extraction non return valve isolation on "1", "2" and "Y heaters third.

Revision BWR SYSTEM LESScOC'_ PLA-NW A. REACTOR WATER CLEANUP SYSTEM B. REFERENCES

1. BWR Systems Manual Chapter- 2.8:,

2. Brown's Ferry Reactor Water Cleanup System Process instrumentation GEK'- 3d533".

3. Brown's Ferry Operation and Maintenance GEK " 779 L Brown's Ferry Leak Detection System GEK - 32559 Z. FNP -Flow Diagrams 47W010, 47W837 BFNM Mechanical Control Diagram 47W6iO-690 BF:IP M, echanical Logic Diagram 47W611-69

6. BFIP Technical Specifications 7.,,Reference Card File 2.8 C. OBJECTI VES The components of the system . . .

~.Flow :azi trouch hi E- s::s em

".. L1ir-ations on the system -

Svs~e- canz-ol o and ocer'ation' of the system

1. Purzose hne Reactor '.a-er Cleanup Svsze' serves :he fo;,owin

• fur. czions: s . . *"  :

..a -Reduces impurities within the water anc tAierefore reducIes rT.e the-deoos~ition of- impurities on 'the Fuel sur-ace.

trars*e' fron-th, Fuel. , "

O lc cess

..... rc there---,r to eiT-her :ne condenser hotwel 1 or ra'asze.

c. c. 'r,,s--.... . :-e -- rj--... sources.

sec-r*,c '= -cary  :-tor:= r-dia-ion

-2

d. Control the concentration of fission products in the feactor orimary system.

e. Maintains high reactor water purity to limit chemical and corrosive action.

2. System Description (Figure 1)

a. Provides continuous mechanical filtration and chemical demineralization of reactor water.

b. Components

1) Recirculation pumps (2)

2) Filter - Demineralizers (2)

3) Regenerative Heat Exchange (3)

) won-regenerative Heat Exchange (2)

5) Valves a) 1Iotor operated valves inside the containment.

b) '.otor operated valves outside the containment.

c) Slowdown flow control valves.

3. :Io, Pa:n (Ficure 1)

a. *,c-icn - Taken from the "A" recirc loop suction line and

ne RPV botzom head drain (to monitor bottom head water

.oera:ure, to prevent temperature stratification in the

oztom head.,which could cause thermal stresses in the RV

coczm ieadand in the CRD stab tubes, and to remove crud

'r:r the bottom of the vessel). The sucticn ro-ir7 is

-..cn to z:e RHR - Shutdown Coolinc mode.

b. :solation valves - Inboard and outnoard oi the primary containmert for the system inlet.

c. C/U Recirc Purps - two 50% capacity pumps.

• . 9ea: Exchancers

• eceer~e~tive seat Exchancers - 3.

'Ze£ce zem;era-ure rom *3z:= to -33:2

".2i ?on-recenerative heat exchangers "- 2 "(Peouce temperature "fur-her from 233'F to l200 F)

e. -iiier-demineralizers

1) Two (50% capacity) used to maintain reactor water purity.

Although the majority of the impurities are removed by the condensate demineralizers, the reactor acts as a concentratorof the remaining impurities. These "are removed by the cleanip system'filter-demineralizers.

.2) Fiiter-demineralize'r6ypass- 'line-l0O% 0capacity f.- Sample Stations

ý(Conductivity measured)-before and after the filter demineralizers

g. Return through the Regenerative Heat Exchann6ers- (temperature increased i form 120OF to 4340 F) to a thermal sleeve in the feedwater lines and into the"RPV>, Check va-lves on feedwater line provide containment isolation.

h. -B1lowdo%,wn path to main condenser or Radwaste.

i. Flow Control

- Constant volumetric flow zhrough the filter-demineralizers.

7Flow control valve and controller for blowdown.

-'. East ".s - s os . Ce-r it n

a. -teactor power operation, - normal water quality.

S.

Szar7-u! -- main*ain water level during n ,lant heatjp.

S . Rec-or blowdown ooeration level:controi wheni not steaLinc.

d. o:'-*0-Standby

e. e ueeliing - react.,c city vwaterý ualI y

a. t: overco7-e -P of sys-e-, line losses, Dressure drc:s

.'s:-- ecuismenz andinfec: re-urn water int.o zte feed-

b. Two - 50: capacity, horizontal, electric motor driven, centri fucal pumps with mechanical seals. Rated flow is 0U-pm eacn.

c. Pump design Data Number Required ................ 2 Capacity (Each) .................... 50%

Discharge Flow (gpm/pump) . .......... ... 180 "Design Temperature (OF)...... . ........ 575 Design Pressure (psig) ............. ... 1450 Discharge Head at Rated Flow (ft) .... ...... 500

d. Normal flows and temperatures 2 pumps, 2F/D units 1 pump, 1 F/D unit 270 opm 135 gpm Temp. from reactor 532CF Temp. to N4on-regex. HX 2330F Temp. from Non-regen. HX 120OF Temo. return to Reactor e3:F

e. rcerazed from tne -ain ccnzr!z" room

f. Pump bearing and seal cooling provided by RSCCW

c. Pumos designed :o o:erate in narallel-system- o.erati.on can continje a: reducec flow wi.- one pump out of servize.

h. F"uto trios

0) inlet isolation valves (I and/or 2) not full open 2' Outlet isolation valve (12) full closed

". Hign oearing cooling water temoerature >VaO°F

-4) Low Recirc pump flow < 30 gpm.

a. Regenerative (RHX) heat exchangers

1) Used to reduce reactor water temperature to avoid excessive demand on the closed cooling water system and minimize heat losses from the reactor system.

2) Cooling medimum is cleanup system return flow to the reactor-shellside (thus improving the system heat cycle).

"3) Design Data Reactor Coolant Flow Rate (lb/hr) ....... 133,300

'Shell Side Pressure (psig) ..... ........ 1,450 Shell Side Temperature (SF) ........ 575 Tube Side Pressure (psig) .... ......... 1,A50 Tube Side Temperature ........... ...... 575

4) Relief valves on shell and tube side provide overpressure protection.

b. Non-regenerative (IIRHX) heat exchanger

., Used to reduce reaczor water temoerature u tc erar~e ievels fcr the resin ,a:eria, used in :-e fire, Ce71ineraliizers.

2` Cooling meaiurn is R7,CC, (sheliside) 3' Desicn data Reactor Coolant Flow Rate (ib/hr). ..... 33.30 Shell Side Pressure.(psig). ........ .... .150 Shell Side Temperature .... .... ...... 370 Tube Side Pressure (psi" ).. . . . . . ....

-Lu"e _ise Te-era-.re r  : . . . . . . . . .

1) Relief valve on tube side provides for heat excnancer isolation protection.

3. Filter - Demineralizers (Figure 2)

a. Used to maintain water purity by mechanical and chemical filtration.- They remove insoluble solid particles and dissloved solids from the water.

b. Two - dual purposes, 50% capacity units of the pressure per coat type which use finely ground mixed ion exchange medium. The filer/demineralizers operate in parallel at 50%ý of the total system capacity.

c. The rapid ion exchange rates at the finely ground resin, requires the use of only a thin pre coat and facilitates greater utilization of the ultimate capacities of the resin. Powdex demineralizer resin is not regenerated. (Solka Floc is not always used under the powdex because powdex is usually a sufficient filtration medium alone - Brown's Ferry doesn't use Solka Floc.)

d. Desion Data Number Required ...................... 2 Capacity (each) ...... ............... .0 Flow Rate/unit (lb/hr) .... ........... 6,650 E,,,uent Conductivily (_:no max) 0.1

-ffluenz......... ................... .. 5 to 7.5 EI-fuent.insolubles (ppb). .......... .<...

.es'gn Temperature ICF). ...... ........... 15C Design Pressure (psic) ........... . .... .

Maximum expected time to remove a unit from service, backwash, Dre coat, and return to service (minutes) ........ ..... 60

e. nnzernai construction 1' Fine Steel mesn . iter ele.ents (sectu') aztac=e: :j a tube sheet..

2) Resin mixture (weight basis)

Cazion : Anion = 2 : 1

f. Filter - Demineralizer effluent specifications Conductivity <0.1.-mho/cm pH 7.0 *- 0.5 Insolubles <lppb (residue on O.OQ5 Micron filter paper)

Chlorides

. - Influent Effluent 200 - lQ00ppb 80' removal

<200ppb 90,: removal

a. Maximum pressure drop (inlet to outlet nozzles)

Clean 5 psid Dirty. 20 psid Alarm 25 psid Automatic isolation 40 psid (effluent valve) miarm

h. Bacl.wasn and precoating required 4if:

I" F/D Differential pressure high : 21-25_psi'd 2', F ' Z,`1ifferentiai cressure Icu : 1 psid

,incicative of possible failed filzer eiemen.t).

3) Effluent conductivity > 0.1 -*mno/c-1 a) hnfluent conductivity <0.1 .mho/cm 0 2G4C Effluent conductivity > 0.1 -.mho/cm @ 25:C

' influent conductivity :-!,.0 _mho/c- S 25C

pH 5.5 to 7.5 Insolubles el opb Silica OF > I.0 Chlorides < 50 ppb AP 20 psig (Decontamination factor (DF) = influent value/effluent "value) c) During startup mode of operation conductivity may exceed 0.1 imho/cm for short periods of time as long as the reactor vessel water quality remains within the limits defined in the technical specifications

i. Post Strainers

.1) Provided to prevent carryover into the reactor system of filter or resin material due to filter element failure.

2) Designed to withstand shutoff head of the cleanup recirculation pumps.

3) Pressure drop clean <5 Alarm 20 psid Automatic Isolazion 20 nsid (F/D effluent valve)

P

?osz strainer backwashing required if differential pressure

=cross it exceeds r -i'=:" 5p psid.

j. £ackwash and precoating done frcm local panel.

1; Automatic or manual sequencing "7) Interlocks allow only one filzer demineralizer to be recoated at a time.

3) Holding DLMp Provided to mainzain :ne filter cnarce unzil tne unit is in service.

o) Pump will auto start if flow through the filter drops to -.0.8 gpm/ft toprevent the precoat from dropping off :he Filter ele-er-s.

4) Elapsed time (expected maximum) - to remove unit from service, backwash, precoat and return to service - 60 minutes.

"k. Flow Control Valve

1) Maintains constant flow r.ate through each filter-demineralizer for varying pressure drops.

2) Set at a local filter - demineralizer control station.

3) Normal Flow is 135 gpm

4. Valves

a. inboard and outboard system inlet. valves are part of the PCIS.

iThe*primary purpose of system isolation valves is to prevent uncovering.the core and limit the radiological dose if the cleanup pipe breaks.

b. All valves are AC powered-exceot the system suction outboard valve (=2 valve) which is 250 VDC.

c. Flow-control valve to radwaste/main condenser (-15 valve)

I) Resrticting orifice upstream prevents excessive blowdown in the event zheFCV failc ooen. Bypassed for low pressure concizions.

2 Upstream pressure-switcn closes FCV or. low pressure tc prevent araining the entire RWCU system piping in a si~hon action to the main condenser cr r=dwasze.

3) Downstream pressure switch closes FCV on hich pressure to-protect the downstream low pressure piping.

.INSTRUME..,,jTATON .

1. Control Room Instruments

a. c.'ow indicazors

- 10 -

1) Cleanup return flow to main condenser or radwaste 0-300 gpm

2) ýiiter Demineralizer "A" flow 0-150 GPm

3) Filter Demineralizer "B" flow 0-150 gpm

b. Pressure indicator, Regen. HX inlet 0-1500 psig

c. Temperature Indicators (1 indicator with selector switch) 0-600'F

1) Reactor water (inlet to RHX, tube side)

2) "Regen. Heat Exchange outlet (tube side)

3) Non-Regen. Heat exchanger Outlet (tube side)

4) Return to feedwater line

d. Conductivity recorders

1) Reactor Water Cleanup before Demin "A" and "B" (1 pen recorder) 1-10 microm hos/cm

2) Reactor Water Cleanup after Demin "A" and "B" (2 oen recorder) 0-1 microm-hos/cm Red - Demineralizer "A" Black - Demnineralizer "B"

2. Sample Station

a. Samples taken at outlet of eacn filzer-demineralizer.

b. :ressure control valves reduce system pressure for use in the samoie station. Caoable o. maintaining continuous flow :hrough each sam'ple point at any cleanup system operating temperature.

c. Constant temperature for zne sampled process fluid.

d. Sample is discharged to clean radwaste.

e. -Ilso sample influent header to filter demineralizers. Difference between infiuent and effluent will determine the filter!

demineralizer efficiency.

Sionificant Alarms, Interlocks, and Trip logic

a. Syszem iolatior. on :ne folVowinc (closure o' inboard ane ouztoard inlet iscaztion valves (=1 and =2) and :ne return Isolation valve (=12) )

-Lzo reactor c .ae' lv_. -"

2) High Temperature'outlet non-regenerative heat exchange 130°F (Alarm also) 3; Szand*v Liquid Control in--i:azed

4) High temperature in areas occupied by cleanup system.equipment 1 10-120°F

5) High temperature in .floordrains in areas occupied by cleanup

• system equipment ll{-120*F "b. Recirculation pump trips-

"1) Inlet Isolation valve (#1) not fully open.

2) Inlet Isolation valve (."2) not fully open.

3) Reactor return isolation valve (-12) fully closed.

a) Pump flow low <30 apm (5sec TD on startup)

5) Pump cooling water outlet High temperature (RECtW I'-O*F.

c. Filter Demineralizers

1) Flow (Local) a) Alarm on low .flow 2

b) Holding-pump auto starts at ý-0.8 gpm/ft

) Differential pressure (Local) a) FilIter-Demineralizer (1) Alarm on high differential pressure @ 25 psid (2) Closed FIT effIluent -valve @ 20 psid

3) Conductivity a) Alarm on FID inlet conductivity @ micro rnho/cm b) Alarm on FfD unit outlet conductivity @ 0.1 -irco mho/cm

d. 3io'-:down (Local)

-'Iarm and closure of drain rio,." corol va,;:e "pic.

2) Alarm and closure of drain flow control valve @ 140 psig.

A Le agge Isolation

a. 8 thermocouples (RTD) located near Cleanup system equipment to monitor the ar6a temperature.

1) Alarm on Panel 9-3 on high temperature-llO° 2O0 F

2) Isolate cleanup system at 1+-2 ---2*O0F

b. 8 temperature switches lecated in floor drains serving cleanup system equipment. Isolate cleanup system 11O0 -120*F G. OPERATIONAL

SUMMARY

1. Modes of Cleanup System Operation

a. Reactor Power Operation - Normal

1) Design bais for the sizing of the Regenerative heat exchanger and main pump discharge piping.

2) Equipment Status Main pumps operating RHX under full load NRHX under partial load Filter-demineralizers ocerating No blowdown

b. S:artup Ocerations i) During plant Startup and heatup at a maximnu raze of l00-F per hour, the reactor water volume will "swell." Additional wazer will be introduced to the reactor from the control rod drive system flow to the reactor. To accomodate tnis increase in vessel water inventory, the cleanuD system is used to discharge reactor water to the main condenser or radwaste.

2) The system drain line restricting orifice bypass valve is c:e. at low reactor pressures.

3) The biowdown rate.is lirited by the Following factors:

Filzer-demineralizer inlet water temperature, RBCCW return temperature and heat exchanger cooling water fs; raze.

S4) The cleanup system removes cantrol rod drive water and "swell" water~from the reactor until reactor temperature reaches lO0-F-above the saturation temperature .for themain turbine seal setpoint pressure; at which time this Water will be removed as steam by blowdown to the main condenser.

5) Equipment Status Main pumps in operation RHX under-partial load NRHX under maximum-startup load Filter-demineralizers in service CRD input and system ekpansion discharged to radwaste or main condenser.

c. lciwdown Operations

1) Design basis for.sizing the blowdown 1l'ne restricting orifice and flow control valve.

2 Cold blowdown a) Can blowdown up .to ::'e capacity of the drain FCV to ra dwa ste---the-con denSe r-...........

t) ECuipment Statuý Main pumps in operation Heat exchangers uncer litzle load Filzer-demineralizers in operation Drain FCV in operation

-ct blc;,ioown a" The "yszeM wi have a res-r~ic-_eG !¢.. " because Gf Lte -imvi:azions on -he maximum a;:owa:ze oulet temperat-ure

-.o R W.. On the she!' side of the -R.XA.c the filt r

_'inera 1er i-le:.*.at---"------

b) If blowdown is in progress with the moderator at 5,510 F with no flow returning to the reactor, System Flow rate must be limited to within the cooling capacity of tne NRRHX.

c) The percent of total system flow blowdcwn must be adjusted to stay within the temperature limitations on the F/D and on the NRHX RBCCW outlet - if the total system flow must be adjusted to operated within the temperature limitations.

d) Equipment Status Main pump (s) operating RHX under no load (entire flow to radwaste/condenser)

NRHX under full load Drain FCV in operation

4) Blowdown to main condenser is the preferred point to limit the duty on the liquid waste processing facilities.

d. Hot Standby

1) Same as Hot blowdown above

2) Minimum NPSH for pumps

e. Refueling Operations I) maximun bypass a) Can be used to blowdown refueling (reactor) wazer, thus with blowdown moce. this oceration shall also covern the blowdown flow conzrol valve sizing.

b) Eýquipment Status Both main pumps operating RHX under no load NRHX under no load Filzer-demineraiizers in operation 3rain FCV in ooeration

.nzire flow discharae to radwaste or -,ain condenser

2) Refuel mode a) in conjunction with-fuel pool cooling and cleanup provides continuous cleaning oF reactor water during refueling.

b) Thd*system may be used to assist in heat removal if required.

c) Equipment Status Main pumps in operation RHX~under no'load' NRHX under no load Filter-demineralizers in operation FCV operational - No blowdown

2. Filter - Demineralizer Basis Operation

a. Filter-demineralizer

1) Two 50 percent capacity, parallel-operated filter demirneralizer units are provided.

2) They are pressure precoat type usiný finely ground, non recenerable, mixed cation and anion-ion exchange resins.

b. Service Cycles

1) The ooeratino'service cycle of a filter-cemineralizer is zer-iinazed either by a nigh pressure drop across the unit or by exhaustion of th'e ion exchange resins. Normally, pressure drop limits the-run "jength except during an abnormal condenser leak.

12)-4hen.-an operating unit's service cycle-is terminated, the unit is isolated byýclosure'of the outiet'valves whil the parallel unit remains in service.

c. Backwash I) The out of filter-demineralizer service re-ove is backwashed a

"ater

,nd tc all of tne soent resins anc

!ccumula-ed insoluDle mazeriaL. Tnis is accomolished wizi the use of an air blast injected into the filzer ce;ineraiizer to dislodce the precoat. Condensate is Then

• um'ec inzo the filter-demineralizer tnroucn the outlez

line. The backwashing process efficiently removes these materials with a minimum volume of water from the condensate system.

2) Sackwash water drains to the cleanup backwash receiving tank. Vent lines from the filter-demineralizer are routed to the backwash receiving tank.

3) The mixture of water and 5 pent resins is pumped to the cleanup phase separator tank of the radwaste system.

d. Precoating

1) After the backwashing-step, the filter-demineralizer is precoated by circulating a slurry of freshly prepared, finely ground, mixed resins from the precoat tank onto the stainless steel holding elements (septum).

2) The slurry deposits evenly on the elements while the water returns to the-precoat tank. Recirculation is continued until the return water is clear.

3) A holding pump is started which will maintain the filter demineralizer cake in place, after which the precoat pump is removed from service and associated valving is closed

4) The unit is then ready to be placed in service by opening the inlet and outlet valves, after which the holding pump is removed from service automatically as flow increases.

5% The holding pump for each filter-demineralizer unit is automatically restarted if tne filier/demineralizer outlet flow drops below 25 gpm. This insures a flow through the filter/demineralizer at all times and prevents the precoat from falling off the element.

. EL ATIO'SX'S WTTH OTHER SYSTE 1 S Reactor Building Closed Cooling Water System which supOlies cooling wazee to the non-recenerative heat exchangers and RWCU recirculation pumos.

2. Primary Containment Isolation System which provides for automatic closure of the RWCU system isolation valves.

- 17 -

3. Radwaste facilities which-are'used to collect wiater from the RWCUJblowdo.'n and spent, resins from the filter-demineralizers.

• . The ""recirculation'loop and the reactor vessel which supply water to the RWCU system.

5. Feedwater line which supplies a return path to the vessel for the processed water. t

6. -The 'Area Leak Detection-System~which provides-an isolation signal for'the RWCU.

7. Standby Liquid Control System which causes isolation of the RWCU upon its in.itiation.

I.ý- TECHNICAL SPECIFICATIONS -- *,

I. Coolant Chemistry - Limiting Conditions for Operation a.-' Prior'to startup'and at Steamina rates less'than 100,00

" -lb/hr the following limits "shall -apply

1) Conductivity 1 - 2.0 micro mho/cm @ 25CC.

2) Chloride 0.1 ppm

b. At Steaming rates greater than 100,000 lb/hr, the following limits shall apply

1) Conductivity 1.0 micro mho/cm @ 25'C.

2) Chloride 0.2 ppm

c. -A: Steamingo rates greater'than 100,000 ib'inr, the reactor water cuality mryyexceed the above.specification only for the time limits~specified below. Exceeding those time limits of -:ne "foliowinbgmaximum quality.1iiits shall be cause for

,-'acing the reactor in the cold shutdown condition.

I) ConductiVity'tiime'eabove 1 micro mho/cm @ 25°C.

-- 2 weeks/year Maximum Limit 10 micro mho/cm @ 25-C.

2) Chloride concentration time abcve 0.2 ppm - 2 weeks/year Maximum Limit-0.5 ppm.

3' -he reacto shall e'shutdcarr, if ýH 5. E or >:..6 'or a "our veriod.

d. When the reactor is not pressurized except during startup, the reactor water shall be maintained within the following limits.

1) Conductivity - 10 micro mho/cm @ 25%C.

2) Chloride - 0.5 ppm

3) pH shall be between 5.3 and 8.6

e. ýWhen the time limits or maximum conductivity or chloride concentration limits are exceeded, an-orderly shutdown shall be initiated immediately. The reactor shall be brought to the cold shutdown condition as rapidly as cooldown rate permits.

f. Whenever the reactor is critical, the limits on acitivity concentrations in the reactorcoolant shall not exceed the equilibrinm valve of 3.2 pCi/gm of dose equivalent 1-131.

This limit may be exceeded following power transients for a maximum of 48 hours5.555556e-4 days <br />0.0133 hours <br />7.936508e-5 weeks <br />1.8264e-5 months <br />. During this acitivity transient the iodine concentrations shall not exceed 26 :Ci/gm whenever the reactor is critical. The reactor shall not be operated more than 5 percent of its yearly power operation under this exception for the equilibrinm activity limits. If the iodine concentration in the coolantexceeds 26 -.Ci/gm, the reactor shall be shutdown, and the steam line isolation valves shall be closed irmnediately.

2. Coolant Chemistry - Surveillance Requirements

a. Reactor coolant shall be continuoly monitored for conductivity.

1) Whenever the continuous conductivity monitor is inoperable and the condensate demineralizers are bypassed, a sample of reactor coolant shall be analyzed for conductivity every A nours. If the condensate demineralizers are in service, a sample of reactor coolant shall be analyzed for conductivity every 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br />.

2) Once a week the continous monitor shall be checked with an in-line flow cell. This in-line conductivity calibration shall be performed ever 2a hours whenever tne reactor coolant conductivity is 51.0 micro mho/cm @ 25°C.

b. During Startup prior to pressurizing the reactor above atmospheric oressure, measurements of reactor water quality shall te perlorr.ed to show confor.ance with I.!.s above

c., Whenever-the reactor is.operating.(including hot Standby conditions, measurements of reactor water quality shall be performed according to the-following schedule:

1) Chloride ion content shall be measured.at least once every 96 hours0.00111 days <br />0.0267 hours <br />1.587302e-4 weeks <br />3.6528e-5 months <br />.

-- 2j) Chloride ion content shall be measured at least every whenever 8 hour9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br />smho/cm reactor conductivity'is >1.0 "micro @ 25°C

3) A sample of primary coolant shall be measured for pH at

-least once every,8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> whenever the ,reactor coolant eonductivity-is >1.0 micro mho/cm @25°C.

.,d.  :'Whenever the reactor is not-pressurized, a-sample of the reactor coolant shall be analyzed at least'every 96 hours0.00111 days <br />0.0267 hours <br />1.587302e-4 weeks <br />3.6528e-5 months <br /> for chloride ion content and pH..

'e. During equilibrium-power operation onisotopic analysis, including quantitative measurements for~at'least 1-131, 1-132, 1-133, and i-134 shall be performed monthly on a coolant liquid sample.

f. Additional coolantonesamples shall be taken whenever the reactor activity exceeds percent of the equilibrium concentration specified in I.l.f-above and one of thefollowing conditions are met:

1) During Star.tup _

2) Following a significant power chance Ta change exceeding lr-:

of rated power in less than 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br />),

3) Following an increase in-the ofTf-as leve, exceeding IC,CO0

.Ci/sec (at the SJAE) within a a8 hour period.

4) Whenever the equilibrium iodine limit specified in l.l.f is exceeded the'addition coolant liquid saiples shall le taken at 4 hour4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> intervals for LI8 hours, or until a stable iodine concentration below the limiting vaie (3.2 -r-m) is established. However, at least 3 consecutive samples shall be taken in all cases. An isotopic analysis shall be performed for each sample, and quan titative measurements made to determine the dose ecuivalent 1-131 concentration.

if the zotal iodine activity of the sample is celow 0.- 'cm, an isotopic a.a.ysi s :o de-errine *cui'&Cflt 1-I31 is'not required.

. Coolant Chemistry Limits Bases

a. The reactor chemistry limits are established to prevent damage to the materials in the primary system which are primarily 304 stainless steel and Zie*aloy cladding.

b. The limit on chloride concentration is to prevent stress corrosion craking'of the stainless steel. For stress corrosion cracking to occur, chlorides and oxygen must be present.

The lower the oxygen concentration, the higher the chloride concentration can be before stress corrosion cracking will occur. Boiling within the reactor results in degeneration of the reactor water. During steaming operation of <100,000 lbs/hr and during'startup, there is not much degeneration taking place and the dissolved oxygen content of the cooling water may be high. Therefore, to assure that no stress corrosion' cracking takes place, a more stringent limit is placed on chloride concentration under these low steaming conditions.

c. When conductivity is in its proper range, pH and chloride and other impurities affecting conductivity will be within limits. When conductivity becomes abnormal, then chloride measurements are made to determine whether or not they are also out of their normal operating valves. Significant changes in conductivity provide the operator with a warning mechanism so he can investigate.

d. The major benefit of cold shutdown is to reduce the temperature dependent corrosion rates and provide time for the cleanup system to re-establish the purity of the reactor coolant.

e. The equilibrium coolant iodine activity limit represents a computed dose to the thyroid of 36 rem at the exclusion distance during the 2 hour2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> period following a steam line break.

f. The maximum activity limit durina a short term transient is established from consideration of a maximum iodine inhalation dose less than 300 rem.

NOTE: Vendor fuel worranties also contain coolant che'm'.istry limits which may be more strigent than the Tecnnical Specifications.

IIIIlit 1-1 lIIN hil1"

16) )AMPI E r0l CON ~I I I ~ DIMIN)I 1 I7 WYitAt OF1 ZI IAmn AO)

I-~ ~ -- -

8110411 LOND I m No. 69

%Ysi live OfI III ',A ALARAM fit It It OLMIN IN I 111,10111t) of fit ifrn, OLmIN oIICII .IMCI(

< CA\

I it FRO SA~lrtI pI.

STATION= FE AIREA I EAK I)EUCLI:IN ARESAFloon DRAIN LEAK TIETEC11ON FIGMIE 1. Reoacto~r Waifi Cluioilis SYslemn

Revision Date BWR SYSTEMS LESSON PLA!N

?--.;A,,R -,E! OrC,,.ROL SYSTE>M B. REFERENCES

1. BWR Systems Manual, Chapter 3.1

-2. GEK 32550- Feedwater Control System- Brown's Ferry

3. System Discussion 7.6 - Reactor Feed Pump and Turbine Drive Peach Bottom "A4. "System'Description 32-2 -'Feedwater Control System and Feed

"-Pump'Tuurbine - Brunswickf

". GEK 779 -"Volume 10- Instruction Manuals for Vendor Supplied "Equi6ment - Brown's Ferry

5. Operating irszruczion 3 - Reactor Feedwater System - Brown's Ferry

7. Svste:.., Diagra's - Brown's Ferry

a. -7;:510 - ,5 - Mechanical Control Diacram.

b. E1T;'1- 2. -'16 - Mechanical Logic Diagrars

c. 4*E PRFD Schematic Diacrams C. Z, I - .

Jr* s:-nd ho-.; system contrbis reactor-water level durinc bozh s-ea:.' saze and transient ccnoizicns.

. -=.rn v"rious .cdes of operazicn and w..hen eAch is a- cy-c.

3. Learn significant system instrumentation,_and interlocks.

Know reiationships between the level control system and other v.

syster's.

=Die e 1o cescribe sysTeri respcnse zo instrum,,entation failures.

-ic tur,

a. Automatically controls the flow of feedwater into the reactor vessel to maintain vesseT water level'within pre-determined levels during al :-odes of plan-- ooera-aion.

1) Required Level.s Determined by:

a) Requirement of Steam Separators (1) Limits Carryover and Carryunder.*

(a) Carryover is inefficient removal of moisture resulting from high vessel level. May damage turbine blading.

(b) Carryunder is caused by low water level allowing uncovering of separator skirt.

Steam from the separators is entrained in the downcomer flow and may cause decreased core subcooling and/or jet oump or recirc pump cavitation.

b) Prevent Uncovering the Core.

2. Modes of Operation

a. Manual

1) Valve Control - used from 0 psi g to approximately 350 psig.

2) Pumo Control- used from 350 osic to approximately I0' Dower.

D. Sincle Element - Automatic "ode

1) Level Controi Only. Only autoratic mode available to byoass valve, also available for RFP Auto-Controls.

c. Three Elements - Automatic I.ode

1) Level, steam flow, feed flow. Anticipates level change due to steam flow-feed flow mismatch.

2) Usually in operation between 10;-" and 100%' power.

31 Only available for RFP Controls.

• ..Sr~o, n -- *'ieure i)

a. Sz-rtuo yvoass alve

1) Controlled by air signal from an electropneumatic (E/Pb

- converteri. ,

2i Operates on level control only for automatic operat'n 3). Varying position of valve(slkchanges feedwater flow which in turn changes reactor water lever

b. Turbine DrivenReactorFeedwater Pumps

.Q) Controlled by Hydraulic System which positions turbinm "Vontrol val vesi

2) Hydraulics System controlled by FWCS to vary pump speed,

. -controlling ratelof feedwater flow.

c. Manual/Auto (M/A) Transfer Stations

1) -One for each RFP turbine

2) Provides a manual demand signal to the turbine speed controls, or

3) Provides automatic control signals from the master

• controller.-to thi turbine speed controls.

d. Master Coptrollers Provides electrical control signal to the .- /A stations; either manual or automatic (automatic described below).

2& C'erazor aUjusts desirea oerazing level wi., set;oinZ

3) Controller comoares-desired level to actual level if in single element control.

U) if they are not the same, controller outout will vary to correct the error.

) Controller comoares desired'level to modified level signal

- if in 3 element, control.

a) 'Steam Flow Z feed flow mismatch signal provides anticimatory level change feature even though actual level may not have changed..

b) If desired level and modified level signals are not the same, controller outout will change to correct

-. e, error.

5) Bypass valve levels controller is level control only.

a) Controller compares actual level to desired level.

(1) If they are not the same, controller output will vary until the error is corrected.

e. Vessel Level vs Flow Error Netwol

1) Modifies level signal based on steam flow - feed flowA condi ti on..

a) If steam flow and~feed flow are equivalent, modifie&

signal wily' correspond to actual-level signa31 b) If steam-flow exceeds feed flow, the modified signal.'

will be less than the aftual°eVel signal.

c) If feed flow exceeds steam flow, the modified signal.

will'be greater than the actual level signal.

f. Steam Flow - Feed Flow Comoarator SCompares total steam flow to total feeGwater flow.

2) If they, are the sate, conara-or outDuz is scme constar:

amssnt.

3; if steam flOw exceeas feed flow, comoara:or output will.

increase.

1) I feed flow e.<ceeds steam flow, ccrparaecr output will decrease.

g. Reaczor 7essel Level Instrumernts

1) Two level transmitters are available via a selector switch, a third transmitter is also used for turbine trio logic.

2) Each level inszrument is oressure (density) ccmoensated.

-- 4

"h. Feedwater Flow Instruments r flow signals =,e sent :o a su-n-c

-,, e.

network for a total feed flow signal.

2)- Feedwater flow signals are density compensated.

%--i.. Steam Flow.-Instrument I) All four steam flow signals are sent to a summing network for a total steam.-flow signal.

2) -Each-flow signal is pressure (density)',compensated.

E. COMPONENT DESCRIPTION

1. Reactor Water Level (Figure 2)

a. 3 Independent Sensors," differentialbpressure transmitters connected to water reference condensing chambers within the, drv,.,ell. 1 of 2 is selected to-be-used in the feedwater control circuitry.

b. Transmitter outputs 10-50 ma,:corresponding to -a level range of 0-60 inches (from inst. zero) is indicated in the control rocm.

c. -'essure compensated-to correct for water density chances Oevel described by differential pressure is related to a

"-.lil of curves whose zero points and slooe chances with

re-s-jre,. -ressire sicnal is aniec to a level correc-:icr T:.r Irocer cc-:Densazion anc inoica:e: in zine con E_-'er roi rcom.

d. Level is also indicatea on 1 pen of a two pen recorder.

' ,.hizhever chanrei is selected as inout the "level

on-rol s/szem -is aso .the channel recorded.

2' Vessel hich anr& low level alarms from the Ievel selected.

, . Level .interlocks and computer -i nputs are from the level channel selected. - - .. .

2.- Veisei-Szear, Flow (Ficure 3)

a. Four steam flow AP transmitters send sicnals via souare root converters to individual steam flow meters in the control room.

b. Pressure Compensation

1) 2nd input to square root converter is pressure from the primary (high) tap of the differential pressure trans mitter. This signal is used tocorrect for changes in steam density as a function of pressure.

c. All four signals summed by total steam-flow summer.

d. Total steam flow signal serves as input to:

1) Level Program Limiter

2) Steam Flow - Feed Flow Error Network 3)' Control Room Total Steam Flow recorder.

I) RWMI Bypass Control Feedwater Flow (Ficure 4): Consisting of 2 individual fiow _P transmi tzers.

a. Each flow signal displayed on CR meters.

b. Both sicnais summed by feedwa-er ficvt summer.

c. Total feedwater flow sional serves as inout tc:

] : F~ow,-Feed :,cw Error :*e-..ork F*.

2) CR Feed Flcw Integrator

3) CR Feed Flow Recorder

-,) Recirc P.umo tJPSH interloc.,

5) ,. *.d

d. temperature Compensation - density chances in feedwater corrected in a multiplier/divider unit.

e. Flow eiements are located beyond the last H.P. heater to

'.-ir'_-_e =ll ie=,-ce sourCes or -ýIow recirculation -;ow inc flna, 7eez'.----, f, 7w-as:,re-n-

A* Feedwater Reaulating Start up Bypass Valve Control (Figure 5),

The bypass valve disc position is controlled by a valve

-)

"operator.

2) Increasing the air pressure applied, to the top of the valve diaphragm closesthe valve against spring pressure.

-- 3) Bleeding off the air pressure* alloW.*'s the valve to open.

4) The air pressure is controlled by a positioner, which in turn is controlled by a small (3- 15#) air signal "from the I/P c6hnerter.

5) The I/P converter output is changed by yarying the valve controller output iignal.

6) The positioner output pressure passes through an air lock valve.

"7) Low instrument air supply pressure (<65=) will cause t.te spring loaded air lock valve to'close.

8) This interrupts the positioner signal and "locks" the air in the valve operator.

9) The valve will not move until sufficient'suoply pressure is available to open the air lock valve.

, t.Fhe oosit-cne- is de-anOinc a fUll c:-r, va"VE

"%wnen air pressure is regainec; the valve will open rapidly,(unless already open).

. Reactor Feed Pump Turbine, Controls (Figure 6) 61 1 rbine speed is de-:errined aT by the cosition of tne :-riFary

=ilot valve bushing. ° '

1) The primary pilot valve bushing is set-by an electric/-",

hydraulic positioner, - the pressure relay pistcn.,;

2) The pressure relay siston is controlled by one of t'io speed changers - the M1otor Gear Unit ('MGU) or Motor' Soeed Changer '(MSC).

Z; The ,.MGU can control turoine spEed 'rom %90 -z.: -5 RPM and is controlled by the fee-water control system.

4) The MSC can control. turbine, speed.from 0 to -,5500 RPM.

and is manually controlled from the control room at either a hich or a low speed chancaS

5) The,!inkage arrangement which.positions the primary pilot" valve busing is a low'v'aluesele'tOr, 'sd that the'lowest' demanid-'sinal from the&MSC or-4IGU W1ill be in control. * '

6) The turbine speed governor, positions the primary pilot valve within its bushing, supplying hydraulic pressure to the primary piston. The reset relay provides feed back to the primary pilot valve bushing for stable oper ation.

7) The primary piston controls the'secondary operating cylinder which positions the turbine control valves.

8) The turbine control valves,(5',low.pressure and one high pressure) aire sequentially opein ed'by' Tiift rods and a liftt beam to admit steam to the turbine. The lift rods are positioned by the 'secondary operating cylinder and are arrange to: 1) Sequentially open the low pressure valves via the lift beam and 2) open the high pressure valve after the last low pressure valve has opened beyond its effective .flow area.

6. in order to understand the electrical portion of the control system, it is necessary to discuss General Electric '.leasurerent and Control (GE/MAC) devices.-,

a. -aci device in a G-!.-..*C ccnzrol system nas an inourt and cutout.

b. " fulll rnce deflection of :ne in.-, sicnal ;roduces an ou:z rancing from 10-50 miIliiamps T--haa*.

1) >maintaining a 10 ma minimum output allows detection-of an electrical failure in the device.

2) irini-um, input signal procuces a 10 .a Outout.

3) A maximum input signal produces a 50 ma output.

c. For example:

i) The reactor vessel level instrument operates cn a .P sional reoresenting 0 - 60" of level.

2) A transducer converts-the 0 - 60" AP sional into a 10 50 na outout signal.

3) T., the reactor water level is 0" (or less), the trans ducer output -is 10 ma.

4) If the wvter level is 33", the transducer output is "32maf( 3=3x-40 ma + 10 ma).-

"5) If the water level !is 60" (or greater), the transducer output is 50 ma.

6) Since a 60" level input change produces a 40 ma output "change, every 3" level change-causes a 2 ma output change.

"d.,-When two'different signals ,are compared, such as steam and feed flow, mismatches between them~may be either positive or negative, i.e.,: steam flow may exceed feed flow (posi t-ive) or feed flow may~exceed steam flow (negative).

e. To allow positive-and negative signals in a device whose out put is always a positive current (10 50 ma), biasing is ermpioyed.

S

f. The bias signal acts as a reference point. Any output creater than the normal bias signal is considered positive.

ny'output less than'the bias signal is-considered negative.

g. For example: (Figure 7)

"The s-eam .low vs. fee- :o,: ccmcarator u-ilizes a s~j-nminc

e;I-ce to dezermine if a fic,q misr.atcn exists.

2, Feed Flow Equals Steam Flow a) If-steam.-fiow-and-feed flow are ecual, tne first sum7er-outout is zero.

-b) The amplifier output is zero.

c) The second summer, adds-the amplifier output and a bias signal.

U1 The bias sicnal is 32-ma (normally).

1) , 2 C-:ý=rxtor cut:put i"

3) FeedFlow Exceeds Steam Flow a T7he first sur7er cu:zu- ,ould :e re-Eazve.

b) This error signal is amplified and sent to the second summer.

c) The negative error signal and the 32 ma bias are added, resulting in a comparator output of <32 ma, which is considered a negative output.

4) Steam Flow Exceeds Feed Flow a) The first summer output would be positive.

b) .This error signal is amplified and sent to the second summer.

c) The positive error signal and the 32 ma bias are added, resulting in a comparator output of >32 ma which is considered a positive output.

h. The mAster level controller is an integrating amplifier.

(Figure 8)

1) The reactor level (or modified reaczor level) is com pared zo a desired level as determined by a setpoint adjust tape.

2) :f they are different. an error siSnai is ge.e-ated and sent :o tWe inzesr:or.

31 The integrator response is shown in Figure 9.

a) A positive error signal into the inzegrazor will cause integrator out:ut to increase until the error signal is cancelled.

b) A negative error signal into the i-tegrazor will cause integrator output to decrease until the error-signal is cancelled.

c) In the absence of any error signal, inzegrator outcut remains constant.

s s,... in Fi, ure 0 . :. v is -a e i r a

.s.cn Manle Aeve .

- 11 -

a) The need for level program is determined during startup testing.

Sb) If used, the program will decrease the operating level at '.-.2"/% rated steam flow; designed to reduce moisture carryover to the main turbine.

c) The program will only be used at power levels above programming limiter setpoint.

d) If installed on currently operating plants, the amplifier modifies at 0/!, rated steam flow with

.the limiter set at 00 steam flow.' (Design for

-use with BWR/6 -systems.)

7. Operation of Feedwater Control System a.' Normal Operation (Figurell).

1i Manual/Auto (M/A) Transfer Stations a) Manual Position (1) The input signal from the master controller is -removed from the circuit.

(2) Control .is from manual control potentiometer.

b) Auto Position

(, The ouzput of tne maszer conzrolier is :assed directly tnrouch -he s:azion -o

-'.:.ransfer the function-cenerator and 1/F converters.

(2) The manual control potentiometer is discon nected- frci- zhe circuit.

c) Ealance Positicn (I) Exactly the s~ae as autonatic insofar as

,"'control-is concerned.

2) Master Controller and Valve Level Controller

lanual Position M.

- 12 -

(1) The output of the maszer controller is the signal from the manual control potentiometer.

(2) The level error signal is disconnected from the outpu-t.of the controller.

b) Auto Position (1) The-output is a signal proportional to desired feedwater flow.

.c) Balance Position (1) Same as auto insofar as control is concerned.

3) RFP Turbine Controls a) During normal operation; the MSC is placed at its High Speed Stops so that the FWCS can control the

!.'GU over its entire speed range.

S) Single Element Control a' A level signal is compared to a desired setpoint in the master controller or valve level controller.

b) If they are the same, the signals cancel each other and no error exists at the input to the intecrator.

c) If there is no error signal, the intecrtor outout is constan;.

d. T7he magnituce of the inzec,'azor ouzout is depencent upon the feedwazer flow de-.and.

e) For examole, assume the following plant conditions:

(Sypass Val ie Operation il ustrated)

T'e olanz is starting up.

".ery little steam flow is required.

The CRD system flow is exactly balancing steam demand.

Reactor water level is stable at 33".

Setpoint taoe is demanding 0(33").

the valve level controller is in auto.

- 13 -

(1) A 33" level signal, is represented by a 32 ma input signal *to the master controller su.mer.

'2' This is exaczlyo-t cd by te

.tare input of 32 ma.

(3) The output of the summer is zero.

(4) The integrator output is at the minimum value of 10 ma.

(5) . 10 ma is applied to the !/P converters, telling the regulating valve to stay. closed.

f) Now assume these conditions:

The plant is still starting up.

CRD reject flow is adjusted greater than CRD flow.

-Reactor-water level has begun to decrease.

Setpoint tape is'demanding 0(33").

SValve level controller is in auto.

(1) As soon as level begins to decrease, a positive error signal. is generated by the summer.

(2) The integrator output begins to ramp uoward.

i3) The increased output causes the feedwater regulating bypass valve to open.

(" 0oeninc the feedwater byvass valve causesre-:'rns an increase in fees flow and r-eactr levei

,o normal.

(5' When reactor level returns to normal, the error signal no longer exists.

(6) with no error signal, the integrator atoutouzsc'e szops ramoing uov,:ard anc stabilize-s new positive value.

(7) The final :result: Steam flow and feed flow are increased: Reactor level is at 33". Integrator outputis >10 ma and the feedwater regulating bypass valve is open slightly.

- 14 -

A) Three Element Control (Ficure 11) (Master Controller Operation Only) a) Steady State Operazion (1) Total steam flow is compared to total feed flow.

(2) At steady state, they are equal and no error signal is generated.

(3) Comparator output is the bias signal (32 ma).

(4) This signal is compared to reactor level.

(5) Normal 33" water level produces 32 ma.

(6) Since both inputsignals are 30 ma, no error signal is generated or amplified.

(7) Level vs. flow error network outpuz is the bias (32 ma).

(8) With the level control mode switch in 3 element control, the 32 ma is sent to the master control ler.

(9) It is corpared to the desired level as deter mined by the set:oint tape and any error is sent to the intecrator.

. ste y state.

.. zc:ual level and -:ire" -eve!

': nor-ally 3' -o-a :heef.re no

(-2 ma, error sicnal is cenerated.

(11) integrator outout will remain constant unless an error signal -s sensed on the inout.

(-2) If integrator cu:-ut is constant, fee;.aze" pu.-,o turbine speed is constant.

b) Steam Flow Exceeds Feed Flow

1) This condition generates a positive error signal ir  :-

(2) The error signal is amplified and summed with the 32 ma bias signal, resulting in a signal

>32 ma.

(3) The level vs. flow error network compares this

-signal 'to the 32 0mna level signal.

(4) A negative error isngenerated, amplified and summed with the 32 ma bias signal, resulting in an output <32 ma. (Modified level signal)

(5) The master controller:compares this modified level signal-with the.32 ma desired level input.

"(6) The resultant positive error signal causes the integrator output to increase.

(7) The feedwater pump turbine(s) increase in speed and feed flow increases until it matches steam flow.

(6) When steam flow and feed flow are equal, the comparator output is 320ma.

(9) Assuming reactoY water level has not changed, the two 32 ma signals-cancel and the error network output is 32 rna.*

(10), This output is identical to zhe desired le'eil and no error signal is generated.

'11) The inteorator cunut 071 s;:: ir"reaslrg since the input errcr signal has We-! =:CE'ec.

i2) Final result: Steam:riow and feed flow are equal, reactor water level is 32", integrator outputliswat some new, higher value and the feed;ater purp twrbines are a: a hicher soeed.

c) Feed Flow Exceeds Steam Flow

'(1) Same asb) except some signs are changed.

.=,levelY 17n cre-se s:-e,':4 a cefore .-e-ur,. *.:. c

' si: as-ec ncz :ochange Ar E r~cse of this cisc.~ss; cn.

- 16 -

5) Bypass Valve Control a) Essentially identical to single element control

.. l.stra. ed'.

b) Normally used for plant start-ups.

b. Abnormal Operation

1) Steam Leak Detection Device (Figure 12) a) ,Compares total steam flowwith Ist stage turbine oressure (a measure of turbine steam flow).

b) A predetermined mismatch actuates an alarm unit.

c) Mismatch annunciation time delayed for 30 seconds.

d) Turbine first stage pressure is indicated on a recorder as turbine steam flow.

2) Loss of Signal (Note: The following assumptions are made with gain of all amos = 1.0) a) Loss of one steam flow input (at lOOS-power, 3 element control)

(1) Total steam flow now indicates 75-t (actual steam flow still 1O00:).

52' Total feed flcw s til 1I00' z 25%r.isma*.ch sensec in fow ccmcarator.

'4) 25:. mismatcn results in a -10 ma error sicnai.

t5; Amolified by 1.0 and summed with 32 ma.

resultant cutout cf flow ccmoa~ator is 22 ma.

(6) Level vs. flow error network comoares zhis signal with normal 33" (32 ma) level signal.

(7) Result is +10 ma error signal, which is summed with 32 ma -or a resultant output of 42 ma.

-17 -

S:- (8).  ?.Master controller summer compares 12 ma with 32 ma. Result is -10 ma error signal sent to intecrator.

.(9) Integrator output decreases to attempt to

- rectify error: signal.

(10)" Feedwater.pump turbines decrease speed,-reducing feedwater flow.

(il)" Although steam f.loiv indication has changed, actual steam flow has not.

(12) Feed-flowjis now less than steam flow and vessel le'vel beginsto decrease.

(13) Thedecreasing.'vessel.level input signal to the level vs flow error netviork begins to offset the erroneous steam flow signal.

(lA) When actual vessel level has decreased to 18",

(a 15"jlevel change) the level input to the level vs. flow error, network is 22 ma (18 x 2 3"ma + 10 ma).

(15) This exactly balances the 22 ma from the steam net

-flow - feed flow comparator and the error "work output returns te 32 ma.

(16)_ Hovever, since an actual steam flow - feed flow mismatch still exisT.zs reaczor level continues

o cecrease.

"(17) This~creates a necative error sicn=-i in tne

.error nezwork, resulting in an ouztut 5f <32 ma.

with 0 18)1T-he- astercontroi er summer compal-es this the desired 32 ma, and a oositive error sional is developed.

(19) Integrator output begins to increase.

until feed (20) Feedwater pump turbines increase soeed flow and steam flow are again equal (at 100%

each -

- 18 -

(21) Reactor vwater level stabilizes at 18".

"(22) Finae result:

Reactor pow-er'is 100,;.

Reactor water level is 18".

Steam flow and feed flow are both 100'.

"Total steam flow'signal is only 75%.

b) Complete loss of steam flow signal (@ 100% power, 3 element control)

(1) Error signal would drive steam flow vs. feed flow comparator output to a minimum signal (10 ma).

(2) Level would have' to decrease below the scram setpoint to compensate for this flow error.

(3) Reactor would scram zn low water level.

c) Loss of one feedwater flow input (100.-' Dower, 3 element control)

(1) Since there are 2 feedwater flow elerent, the loss of one inout corresponds to a 50%' loss of feedwater signal.

(2) The resultant flow error demands more feedwater

!Ow.

level begins to increase.

(4) A 30" level increase (to +62") would offset the flow error and return feedwater flow :o 110:-.

(5) Since the main turnine and RFP's trips at

+54", the transient will result in a scram.

d) Complete loss of feedwater flow input (at I00" po-aer, three element control)

(1) The large flow error will cause level to increase

-o "-- " .,,,hen -In ---- in r trim *esu, tina in a scr=..

- 19 -

e) Loss of level input (100% power, 3 element control)

(1) Essentially the same As zero level.

(2) Master controller output tries to increase level by increasing feedwater pump turbine speed to maximum.

(3) Level will increase until RFP's and main turbine trip at +54".

f) Loss of control signal to turbine speed controls (1) Would cause reduction of speed to low speed stops of Motor Gear Unit (MGU) for RFP turbine affected.

(2) Control signal failure alarm unit (Figure 12) monitors signal and trips if it falls below the normal range (10-50 ma). Normally set at -A ma.

(3) Results in interruption of power to the MGU (lockup) which fails "as is", thus turbine speed is fixed.

(L) Control of the turbine (manual only) can be regained by lowering the motor speed chancer (MMC) until it is the lower demand value, then energizing a hydraulic jack solenoid.

(5) The hydraulic jack will use turbine controi oii pressure to r.ove zne HGU to its high speed stops, allowing the MSC full rance speed control of the RFPT.

(6) The signal failure is a seal-in function and must be manually reset wien zýe control sicnai is available. Ncte: The .I'GU demand from the

./A station must be run to demand full scale (HSS) of the MGU before resetting.

g) High Reactor Vessel Water Level (1) For turbine protection, turbine trips are initi ated on high water level.