ML17264A977

Rev 11 to AP-RCP.1, RCP Seal Malfunction.

ML17264A977
Person / Time
Site:	Ginna
Issue date:	08/05/1997
From:	ROCHESTER GAS & ELECTRIC CORP.
To:
Shared Package
ML17264A976	List: ML17264A975 ML17264A977 ML17264A978 ML17264A979 ML17311A050
References
AP-RCP.1, NUDOCS 9708130125
Download: ML17264A977 (32)

Text

EOP: AP-RCP.1 TITLE: RCP SEAL MALFUNCTION REV 11 PAGE 1 of 10 ROCHESTER GAS AND ELECTRIC CORPORATION GINNA STATION CONTROLLED COPY NUMBER RESPONSIBLE AGER EFFECTIVE DATE CATEGORY 1.0 REVIEWED BY: 9708i30125 970805 PDR ADOCK 05000244 PDR EOP: AP-RCP.1 RCP SEAL MALFUNCTION REV 11 PAGE 2 of 10 A.PURPOSE-This procedure provides the instructions necessary to diagnose and to respond to a reactor coolant pump seal malfunction.

B.ENTRY CONDITIONS/SYMPTOMS 1.ENTRY CONDITIONS

-This procedure is entered from: a.E-3, STEAM GENERATOR TUBE RUPTURE, or b.ES-l.l, SI TERMINATION, or c.ES-1.2, POST LOCA COOLDOWN AND DEPRESSURIZATION, or d.ECA-0.1, LOSS OF ALL AC POWER RECOVERY WITHOUT SI REQUIRED, or e.ECA-2.1, UNCONTROLLED DEPRESSURIZATION OF BOTH STEAM GENERATORS, or f.ECA-3.1, SGTR WITH LOSS OF REACTOR COOLANT-SUBCOOLED RECOVERY DESIRED, or g.ECA-3.2, SGTR WITH LOSS OF REACTOR COOLANT-SATURATED RECOVERY DESIRED,.or h.ECA-3.3, SGTR WITHOUT PRESSURIZER PRESSURE CONTROL, or i.FR-I.1, RESPONSE TO HIGH PRESSURIZER LEVEL, when RCP seal malfunction is indicated.

2.SYMPTOMS-The symptoms of RCP SEAL MALFUNCTION are;a.Annunciator B-17(18), RCP A(B)No.1 SEAL HI-LO FLOW 5.0 GPM 1.0 , lit, or b.Annunciator B-9(10), RCP A(B)LABYR SEAL LO DIFF PRESS 15" H20, lit, or c.Annunciator B-3(4), RCP A(B)STAND PIPE HI LEVEL+1 FT, lit, or Continued on next page AP-RCP.1 RCP SEAL MALFUNCTION REV: 11 PAGE 3 of 10 2.SYMPTOMS (cont)d.Annunciator B-ll(12), RCP A(B)STAND PIPE LO LEVEL-4 FT, lit, or e.Annunciator B-25(26), RCP A(B)No.1 SEAL LO DIFF PRESS 220 PSID, lit, or f.Annunciator B-l(2), RCP A(B)No.1 SEAL OUT HI TEMP 200'F, lit, or, g.Annunciator A-7(15), RCP A(B)CCW RETURN HIGH TEMP OR LOW FLOW, lit.

EOP: AP-RCP.1 TITLE: RCP SEAL MALFUNCTION REV 11 PAGE 4 of 10 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED CAUTION o IF, AT ANY TIME DURING THIS PROCEDURE, A'EACTOR TRIP OR SI OCCURS, E-O, REACTOR TRIP OR SAFETY INJECTION, SHALL BE PERFORMED.

o IF ANY RCP IS TRIPPED, THEN SHUTDOWN MARGIN REQUIREMENTS SHOULD BE VERIFIED (REFER TO 0-3.1, BORON CONCENTRATION FOR XENON FREE ALL RODS IN MOST REACTIVE ROD STUCK OUT SHUTDOWN MARGIN).o IF A RCP IS SECURED BECAUSE OF A SEAL MALFUNCTION, IT SHOULD NOT BE RESTARTED UNTIL THE CAUSE OF THE MALFUNCTION HAS BEEN DETERMINED AND CORRECTED.

NOTE;o If a Reactor trip is iTIitiated while performing Step 1, transition to E-0 should occur while completing subsequent actions of the step.o Total¹1 Seal Flow is defined as the sum of indicated¹1 Seal Leakoff Flow and RCDT leak rate (PPCS Point ID L1003, 3.2 gal/8 in the normal operating range).1 Check Total$1 Seal Leakaff Flows-LESS THAN 8.0 GPM IF a¹1 Seal Failure is verified by a decrease in Labyr Seal Diff Pressure OR increasing Seal Inlet/Outlet temps, THEN perform the following:

a.IF reactor trip breakers closed, THEN trip the reactor.b.Trip the affected RCP(s).c.Allow 4 minutes for pump coast down, THEN close affected RCP(s)seal disch valve.~RCP A, AOV-270A~RCP B, AOV-270B d.IF reactor trip was NOT required, THEN go to Step 4.

EOP: AP-RCP.1 RCP SEAL MALFUNCTION REV 11 PAGE 5 of 10 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED 2 Check RCP Seal Return Valve Alignment:

a.RCP seal return isolation valve, MOV-313-OPEN a.Perform the following:

1)Ensure CI reset.2)Ensure both trains of XY relays for RCP seal return isolation valve, MOV-313, reset.3)Open RCP seal return isolation valve, MOV-313.IF MOV-313 can NOT be opened, THEN dispatch AO to AUX BLDG with RWST area key to check valve and breaker locally (breaker MCC C position 13J).b.Verify RCP seal disch valves OPEN~RCP A, AOV-270A~RCP B, AOV-270B b.Manually open valves.IF valves can NOT be opened, THEN verify IA aligned to CNMT and go to Step 3.

I 0 f EOP: AP-RCP.1 TITLE: RCP SEAL MALFUNCTXON REV 11 PAGE 6 of 10 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED V NOTE: o If a reactor trip is initiated while performing Step 3, transition to E-0 should occur while completing subsequent actions of the step.o The 0.8 GPM limit for¹1 seal flow applies when the RCS is at normal operating pressure.Refer to Figure RCP SEAL LEAKOFF and consult plant staff for guidance if the RCS is at reduced pressure.3 Check Total gl Seal Flow-BETWEEN 0.8 GPM AND 6.0 GPM IF¹1 Seal Inlet and Outlet temperatures are increasing, THEN perform the following:

a.IF reactor trip breakers closed, THEN trip the reactor.b.Trip the affected RCP(s).c.Allow 4 minutes for pump coast down, THEN close affected RCP(s)seal disch valve.~RCP A)AOV-270A~RCP B)AOV-270B IF¹1 Seal Inlet and Outlet temperatures are stable, THEN perform the following while continuing with this procedure.

o IF total¹1 Seal Flow greater than 6.0 gpm, THEN maintain seal injection flow rate of 9.0 GPM or greater to the affected RCP.o IF total¹1 Seal flow exceeds 8.0 GPM OR Seal Inlet/Outlet temperatures begin to increase, THEN return to Step 1.o Prepare for orderly pump shutdown by placing the plant in Hot Shutdown using 0-2.1, NORMAL SHUTDOWN TO HOT SHUTDOWN.o Secure the affected RCP with 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br />.

EOP: AP-RCP.1 RCP SEAL MALFUNCTION REV 11 PAGE 7 of 10 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED NOTE: Attachment RCP DIAGNOSTICS may be used to aid in diagnosis.

4 Check RCP Cooling: o Annunciator A-7, RCP A CCW RETURN HIGH TEMP OR LOW FLOW-EXTINGUISHED o Annunciator A-15, RCP B CCW RETURN HIGH TEMP OR LOW FLOW-EXTINGUISHED Perform the following:

a.Verify RCP CCW supply and return valves open.~RCP A, MOV-749A and MOV-759A~RCP B, MOV-749B and MOV>>759B b.En'sure open CCW outlet valves from RCP thermal barriers.~RCP A, AOV-754A~RCP B, AOV-754B 5 Check RCP g2 Seal Indications:

o Annunciator B-3, RCP A STANDPIPE HI LEVEL+1 FT-EXTINGUISHED' Annunciator B-4, RCP B STANDPIPE HI LEVEL+1 FT-EXTINGUISHED IF affected RCP¹1 seal leakoff flow decreasing, THEN failure of¹2 seal may be indicated.

Continue plant operation while closely monitoring RCP seal indications.

EOP.AP-RCP.1 TITLE: RCP SEAL MALFUNCTION REV: 11 PAGE 8 of 10 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED CAUTION REDUCING CHARGING FLOW'WILL RESULT IN INCREASING REGEN HX OUTLET TEMPERATURE.

6 Check RCP Labyrinth Seal D/Ps-GREATER THAN 15 INCHES OF MATER Perform the following:

a.Ensure open CCW outlet valves from RCP thermal barriers.~RCP A, AOV-754A~RCP B, AOV-754B b.Verify seal injection flow greater than 5 GPM for affected RCP.c.Adjust HCV-142 as necessary.

d.Dispatch AO to check seal injection filter D/P.e.Check CCW surge tank level stable.IF level increasing, THEN go to AP-CCW.l, LEAKAGE INTO THE COMPONENT COOLING LOOP.7 Check RCP g3 Seal Indications:

o Annunciator B-ll, RCP A STAND PIPE LO LEVEL-4FT-EXTINGUISHED o Annunciator B-12, RCP B STAND PIPE LO LEVEL-4FT-EXTINGUISHED Check CNMT radiation monitors normal.~R-11~R-12 IF RCP standpipe level low and CNMT radiation'increasing, THEN¹3 seal leakage increase is probable.Continue plant operation while closely monitoring RCP seal indications.

1'l F.OP: AP-RCP.1 LITLE: RCP SEAL MALFUNCTION REV 11 PAGE 9 of 10 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED NOTE: In the absence of other seal failure indications, an elevated¹1 seal outlet temperature may indicate pump bearing damage.*8 Monitor Plant Conditions:

a.RCP¹1 seal flow o Total¹1 seal leakoff flow-LESS THAN 6.0 GPM o Total¹1 seal flow-GREATER THAN 0.8 GPM a.IF affected RCP running, THEN return to Step 1.IF NOT, THEN perform the follow'ing:

1)Monitor affected RCP (Refer to Attachment RCP DIAGNOSTICS).

b.RCP¹1 Seal Flow-WITHIN THE NORMAL OPERATING RANGE OF FIGURE RCP SEAL LEAKOFF 2)Consult Plant Staff to determine if cooldown required.b.Perform the following:

o Ensure seal injection flow exceeds¹1 seal leakoff flow.o Refer to S-2.1, Reactor Coolant Pump Operation.

o Consult plant staff for further instructions.

c.RCP¹1 seal outlet temperatures LESS THAN 215'ND STABLE d.RCS leakage-NORMAL (Refer to leakage surveillance sheet)c.IF pump bearing damage is suspected, THEN notify plant staff and expedite shutdown of the affected RCP.IF NOT, THEN return tc Step 1.d.Perform the following:

1)Calculate RCS leakrate.2)Refer to ITS section 3.4e13.

AP-RCP.1 T RCP SEAL MALFUNCTION REV: 11 PAGE 10 of 10 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED NOTE: Refer to 0-9.3, NRC IMMEDIATE NOTIFICATION, for reporting requirements.

9 Notify Higher Supervision-END-EOP: AP-RCP.1 TITLE: RCP SEAL MALFUNCTION REV: 11 PAGE 1 of 1 AP-RCP.1 APPENDIX LIST TITLE r 1)FIGURE RCP SEAL LEAKOFF 2)ATTACHMENT RCP DIAGNOSTICS PAGES EOP: AP-RCP.1 T!ZLE: RCP SEAL MALFUNCTION REV: 11 PAGE 1 of 1 FIGURE RGP SEAL LEAKOFF O'I SEAL LEAK RATE (GPM)6 LEAK RATE INCREMENTS 0.2 GPH NORMAL OPERATING RANGE DP INCREMENTS 50 PSI 250 500 750 1000 1250 1500 1750 2000 2250 2500 81 SEAL DP (RCS PRESS-VCT PRESS)PSI EOP: ,P-TURB.5'f ITLE: RAPID LOAD REDUCTION REV'PAGE 1 of 11 ROCHESTER GAS AND ELECTRIC CORPORATION GINNA STATION CONTROLLED COPY NUMBER TECHNICAL REVIEW RES 0 SIBLE MANAGER EFFECTIVE DATE CATEGORY 1.0 REVIEWED BY:

0 EOP: 'P-TURB.5 RAPID LOAD REDUCTION REV: 1 PAGE 2 of 11 A.PURPOSE B.ENTRY CONDITIONS/SYMPTOMS 1.ENTRY CONDITIONS

-This procedure is entered from a.The SS has determined that a rapid load reduction is required.

EOP: P-TURB.5[ITl.E: RAPID LOAD REDUCTION REV: 1 PAGE 3 of 11 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED*************

x*x*x*x**x*x x***************

CAUTION o IF AT ANY TIME DURING THIS PROCEDURE, A REACTOR TRIP OR SI OCCURS, THEN E-O, REACTOR TRIP OR SAFETY INJECTION, SHALL BE PERFORMED.

o IF MAIN FEEDWATER FLOW SHOULD DECREASE TO 25%OF FULL POWER VALUE (.825 E+6 LBM/HR)PRIOR TO THE AMSAC SYSTEM AUTOMATICALLY BLOCKING, THEN A TURBINE TRIP AND AUX FEED PUMPS START COULD RESULT.********x*******x x x x*x x x x x*x x**x*x****x**

NOTE: o This procedure is intended for use when the required load reduction rate is)1%/min.o A maximum continuous load reduction rate of)5%/min would not normally be used unless otherwise directed by the Shift Supervisor.

• 1 Initiate Load Reduction a.Verify ROD CONTROL BANK SELECTOR SWITCH is in AUTOMATIC a.IF Auto Rod Control is inoperable OR Manual Control is desired, THEN perform the following:

1)Place ROD CONTROL BANK SELECTOR SWITCH to MANUAL.b.Reduce turbine load using Auto Turbine EH Control if desired 1)Select desired rate on thumbwheel 2)Insert Rods as necessary to match Tavg and Tref.b.IF Auto Control is inoperable OR Manual Control, is desired, THEN reduce turbine load in manual as desired.2)Reduce the setter to the desired load 3)Depress the GO button c.Verify Steam Dump operating in auto, as required c.Place Steam Dump in manual and operate as necessary.

EOP: P-TURB.5 TITLE: RAPID LOAD REDUCTION REV 1 PAGE 4 of 11 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED***********x x x x*x**x***x**x x x x x x x*x x*x*x x CAUTION EXTREME AND RAPID ROD MOTION TO MITIGATE TAVG SWINGS MAY RESULT IN LARGE POWER EXCURSIONS AND SHOULD BE AVOIDED.**************x x x x x****x*x x*x x x x x*x x x*x*x 2 Monitor RCS Tavg o Tavg-GREATER THAN 545'F o Tavg-LESS THAN 578'F Verify AUTO control rod motion as required.IF NOT, THEN place rod control bank selector switch to MANUAL and adjust control rods as necessary.

IF Tavg is outside limits AND CANNOT be controlled, THEN trip the reactor and go to E-O, REACTOR TRIP OR SAFETY INJECTION.

NOTE: A thumb rule for initial boron addition is-2 gal/0 load reduction.

3 Add Boric Acid As Necessary To: o Maintain or return a Flux to the target band o Maintain control rods above insertion limits o Match Tavg and Tref o Compensate for xenon EOP: P-TURB.5 TlTLE: RAPID LOAD REDUCTION REV: l PAGE 5 of ll STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED NOTE: It is permissible to operate RCPs for limited periods without seal injection, provided CCW is being supplied to the thermal barriers.4 Check IA Available To CNMT o IA pressure->60 psig o Instr Air to CN>lT Isol Valve, AOV-5392-OPEN Control PRZR level and pressure and follows: I o Adjust load reduction rate o Ensure control rods are moving to control Tavg o Secure charging pumps if necessary o Operate proportional and backup heaters as required 5 Monitor Plant Parameters-CONTROLLING AT OR TRENDING TO PROGRAM VALUES~PRZR Pressure~PRZR Level~S/G Level IF any parameter is approaching a trip setpoint AND CANNOT be controlled, THEN trip the reactor and go to E-O, REACTOR TRIP OR SAFETY INJECTION.

NOTE: The load reduction should not be delayed to perform the remaining steps.6 Check If Condensate Booster Pumps Should Be Secured a.Power<65%OR Trim Valve V-9508G indicates>80%open a.Go to Step 13.b.Place the auto condensate booster pump to the trip position c.Stop one condensate booster pump d.WHEN the condensate system stabilizes, THEN stop the remaining condensate booster pump EOP: 'P-TURB.5 I'I TLE: RAPID LOAD REDUCTION REV: 1 PAGE 6 of 11 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED 7 Check If One MFW Pump Should Be Secured a.Power<50%a.Go to Step 13.b.Verify at least one MFWP Seal Booster pump in service b.Notify AO to start one MFWP Seal Booster pump c.Two MFW Pumps running c.Go to Step 8.d.Close discharge valve for the pump to be secured~MFW Pump A-MOV-3977~MFW Pump B-MOV-3976 e.Stop the desired MFW Pump f.Close the secured MFW pump recirc valve by placing the control switch in pull stop g.Close the service water block valve to the secured MFW pump oil cooler~MFW Pump A-V-4701~MFW Pump B-V-4702 8 Verify Trim Valves Controlling Condensate System Pressure in Auto (300-375 PSIG)Place controller in manual and adjust pressure as necessary EOP: P-TURB.5 T,I TLE: RAPID LOAD REDUCTION REV: 1 PAGE 7 of 11 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED 9 Check ANSAC System Status a.Power<35%(-150 psig first stage pressure)b.Verify AMSAC Auto Block Status Light is ON a.Go to Step 13.b.Place AMSAC Manual Block switch to the BLOCK position 10 Check Heater Drain Tank Pump Status a.Generator load<175 MWe b.Stop one Heater Drain Tank Pump c.WHEN Heater Drain Tank level control is stable, THEN stop the second Heater Drain Tank Pump a.Go to Step 13.11 Check FW Flow Bypass Vlv Status a.Power<30%b.FW Flow Bypass Vlvs in AUTO~HCV-480~HCV-481 a.Go to Step 13.b.Perform the following:

1)Slowly open the FW Flow Bypass Vlvs while verifying the associated FW Reg Vlv compensates by closing slightly 2)Place FW Flow Bypass Vlvs in AUTO EOP: P-TURB.5 RAPID LOAD REDUCTION REV 1 PAGE 8 of 11 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED 12 Align Systems For Low Power Operation a.Power<30%a.Go to Step 13.b.Place AOU-3959, CNDST Bypass Ulv to CLOSE c.Place LC-107, Hotwell Level Control, to MANUAL d.Generator load<100 MWe e.Open turbine drain valves d.Go to Step 13.13 Evaluate Plant Status a.Power stable at desired level a.IF power)20%and further reduction is required, THEN continue load reduction and return to Step 6.IF power<20%and further reduction is required, THEN refer to procedure 0-2.1, NORMAL SHUTDOWN TO HOT SHUTDOWN.

EOP: P-TURB.5 jITLE: RAPID LOAD REDUCTION REV: 1 PAGE 9 of 11 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED 14 Establish Stable Plant Conditions:

a.Tavg-TRENDING TO TREF a.Perform the following:

1)Verify AUTO control rod motion as, required.IF NOT, THEN place rod control bank selector switch to MANUAL and adjust control rods as necessary.

2)Borate if required for power reduction.

b.PRZR pressure-TRENDING TO 2235 PSIG b.Verify proper operation of PRZR heaters and spray OR take manual control of PRZR pressure controller 431K.IF PRZR pressure can NOT be controlled, THEN refer to AP-PRZR.1, ABNORMAL PRESSURIZER PRESSURE.c.PRZR level-TRENDING TO PROGRAM c.Verify proper operation of charging pump speed controllers OR take manual control of speed controllers to control PRZR level.d.Rod insertion limit alarms EXTINGUISHED d.Borate as necessary and withdraw control rods to clear insertion limit alarms (refer to affected rod bank alarm response procedures if necessary).

e.Narrow range S/G levels TRENDING TO PROGRAM LEVEL e.Ensure MFW regulating valves controlling in AUTO, OR control feedwater in MANUAL.

EOP: P-TURB.5 TITLE: RAPID LOAD REDUCTION REV'PAGE 10 of 11 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED 15 Establish Normal Plant Conditions:

a.Verify EH control in OPER PAN and IMP IN b.Verify steam dump controller, HC-484, in AUTO at 1005 psig c.Verify annunciator G-15, STEAM DUMP ARMED-EXTINGUISHED a.IF conditions requiring manual operation have cleared, THEN place EH in OPER PAN and IMP IN.c.IF Tavg within 6'F of Tref, THEN perform the following:

1)Ensure steam dump valves closed.d.Verify PRZR presssure control in AUTO 2)Reset steam dump.d.Place PRZR pressure control in AUTO as desired.~431K master controller

~PRZR spray valve controllers

~PRZR heater controllers e.Verify PRZR level control in AUTO)e.Place one charging pump speed controller in AUTO if desired.f.Verify Rod Control Selector Switch in AUTO f.Place Rod Control Selector Switch in AUTO if desired.NOTE: Refer to 0-9.3, NRC IMMEDIATE NOTIFICATION, for reporting requirements.

16 Notify Higher Supervision FOP: P-TURB.5%1TLE: RAPID LOAD REDUCTION REV 1 PAGE 11 of 11 STEP ACTION/EXPECTED RESPONSE RESPONSE NOT OBTAINED 17 Refer to 0-5.1, LOAD REDUCTIONS, for additional"guidance 18 Return To Procedure Or Guidance In Effect-END-

I~P EOIa: ATT-9.0 TITLE: ATTACHMENT LETDOWN REV: 5 PAGE 1 of 1 Superintendent

.Y~.I nate 7 A'i A)The following conditions must be met to place either normal or excess letdown in service: o IA to CNMT-ESTABLISHED Q CCW-IN SERVICE o PRZR level-GREATER THAN 13%B)Establish Normal Letdown: 1.Establish charging line flow to REGEN Hx-GREATER THAN 20 gpm.2.Place the following switches to CLOSE: o Letdown orifice valves (AOV-200A, AOV-200B, and AOV-202)o AOV-427, loop B cold leg to REGEN Hx 3.Place letdown controllers in MANUAL at 40%open: o Temperature control valve, TCV-130 o Pressure control valve, PCV-135 4.Verify AOV-371, letdown isolation valve-OPEN.5.Open loop B cold leg to REGEN Hx, AOV-427.6.Open one 40 gpm letdown orifice valve (AOV-200A or AOV-200B).

7.Place TCV-130 in AUTO at 105'F.8.Place PCV-135 in AUTO at 250 psig.9.Adjust charging pump speed and HCV-142 as necessary to stablizie PRZR level and maintain RCP labyrinth seal D/P.C)IF normal letdown can NOT be established, THEN establish excess letdown: 1.Place AOV-312 to NORMAL.2.Ensure CCW from excess letdown Hx, (AOV-745)-OPEN.3.Open excess letdown isolation valve AOV-310.4.Slowly open HCV-123 to maintain excess letdown temperature less than 195'F and pressure less than 100 psig.1 5.Adjust charging pump speed as necessary to stabilize PRZR level and maintain RCP labyrinth.seal D/P.

Distribution Sheet Distri-.txt~Hi$PP>/~a~~Priority: Normal From: E-RIDS1 Action Recipients:

RidsNrrPMGVissing Copies: 0 OK Internal Recipients:

RidsRgn1 MailCenter RidsNrrDipmEphp Rids Mana ger IRO DHa an Fl E CENTER Ol Dennis Hagan External Recipients:

0 1 1 0 0 0 OK OK OK Paper Copy Paper Copy OK Total Copies: Item: ADAMS Document Library: ML ADAMS" HQNTAD01 ID'03719331:1

Subject:

Revision 22 to Ginna Station Emergency Plan Implementing Procedure 5-2.Body: ADAMS DISTRIBUTION NOTIFICATION.

Electronic Recipients can RIGHT CLICK and OPEN fhe first Attachment to View the Document in ADAMS.The Document may also be viewed by searching for Accession Number ML003719331

~A045-OR Submittal:

Emergency Preparedness Plans, Implementing Procedures, Corre Page 1 spondence Distri>>2.txt Docket: 05000244 Page 2