ML13273A037: Difference between revisions
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
StriderTol (talk | contribs) (StriderTol Bot change) |
||
(4 intermediate revisions by the same user not shown) | |||
Line 3: | Line 3: | ||
| issue date = 09/26/2013 | | issue date = 09/26/2013 | ||
| title = Fourth Ten-Year Inservice Inspection Plan, Request for Relief No. 13-ON-001 | | title = Fourth Ten-Year Inservice Inspection Plan, Request for Relief No. 13-ON-001 | ||
| author name = Batson S | | author name = Batson S | ||
| author affiliation = Duke Energy Carolinas, LLC | | author affiliation = Duke Energy Carolinas, LLC | ||
| addressee name = | | addressee name = | ||
Line 16: | Line 16: | ||
=Text= | =Text= | ||
{{#Wiki_filter:DUKE Scott L. Batson Vice President LI4LIR Ie Oconee | {{#Wiki_filter:DUKE Scott L. Batson Vice President LI4LIR Ie Oconee NuclearStation Duke Energy ONO1VP I 7800 RochesterHwy Seneca, SC 29672 September 26, 2013 o:f 864.873. | ||
864.873.3274 4208 Scott.Batson@duke-energy.com ATTN: Document Control Desk U. S. Nuclear Regulatory Commission 11555 Rockville Pike Rockville, Maryland 20852-2746 | |||
==Subject:== | ==Subject:== | ||
Duke Energy Carolinas, LLC Oconee Nuclear Station Unit 3 Docket No. 50-287 Fourth Ten-Year Inservice Inspection Plan Request for Relief No. 13-ON-001 Pursuant to 10 CFR 50.55a(g)(5)(iii), attached is a Request for Relief from the requirement to examine 100% of the volume specified by the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME Code), Section Xl, Rules for Inservice Inspection of Nuclear Power Plant Components, 1998 Edition with 2000 Addenda (as modified by Code Case N-460).The attached Request for Relief 13-ON-001 is to allow Duke Energy to take credit for the enclosed Table 1 list of limited ultrasonic examinations performed on welds associated with various systems and components during Unit 3 EOC26 refueling outage. The ultrasonic examination coverage of the subject Unit 3 welds did not meet the examination coverage requirements of Code Case N-460. The coverage examination obtained for each weld is provided in Attachment A of the relief request.Achievement of greater examination coverage for these welds is impractical due to piping/valve geometry and interferences. | Duke Energy Carolinas, LLC Oconee Nuclear Station Unit 3 Docket No. 50-287 Fourth Ten-Year Inservice Inspection Plan Request for Relief No. 13-ON-001 Pursuant to 10 CFR 50.55a(g)(5)(iii), attached is a Request for Relief from the requirement to examine 100% of the volume specified by the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME Code), Section Xl, Rules for Inservice Inspection of Nuclear Power Plant Components, 1998 Edition with 2000 Addenda (as modified by Code Case N-460). | ||
Therefore, Duke Energy requests that the NRC grant relief as authorized under 10 CFR 50.55(g)(6)(i). | The attached Request for Relief 13-ON-001 is to allow Duke Energy to take credit for the enclosed Table 1 list of limited ultrasonic examinations performed on welds associated with various systems and components during Unit 3 EOC26 refueling outage. The ultrasonic examination coverage of the subject Unit 3 welds did not meet the examination coverage requirements of Code Case N-460. The coverage examination obtained for each weld is provided in Attachment A of the relief request. | ||
Achievement of greater examination coverage for these welds is impractical due to piping/valve geometry and interferences. Therefore, Duke Energy requests that the NRC grant relief as authorized under 10 CFR 50.55(g)(6)(i). | |||
This submittal document contains no regulatory commitments. | This submittal document contains no regulatory commitments. | ||
Ifthere are any questions or further information is needed you may contact Corey Gray at (864)-873-6325. | |||
Sincerely, Scott L. Batson, Site Vice President Oconee Nuclear Station Attachment A www.duke-energy.com U. S. Nuclear Regulatory Commission September 26, 2013 Page 2 Xc w/att: Mr. Victor Mcree Region | Sincerely, Scott L. Batson, Site Vice President Oconee Nuclear Station Attachment A www.duke-energy.com | ||
Oconee Relief Request 13-ON-001 2.0 Weld # 3-PZR-WP26-1 2.1. ASME Code Component(s) | U. S. Nuclear Regulatory Commission September 26, 2013 Page 2 Xc w/att: Mr. Victor Mcree Region IIAdministrator U. S. Nuclear Regulatory Commission Marquis One Tower 245 Peachtree Center Ave., NE, Suite 1200 Atlanta, GA 30303-1257 Mr. Richard Guzman Project Manager (by electronic mail only) | ||
Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-1, Summary Number 03.B3.110.0009, and ASME Code Class 1.2.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda.2.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-l. | US Nuclear Regulatory Commission One White Flint North, Mail Stop O-8C2 11555 Rockville Pike Rockville MD 20852-2738 Xc w/o attachment Mr. Eddy Crowe NRC Senior Resident Inspector Oconee Nuclear Station Ms. Susan Jenkins Section Manager Division of Waste Management Bureau of Land and Waste Management SC Dept. of Health & Environment Control 2600 Bull St. | ||
2.4. Impracticality of Compliance Component configuration" Surface 1: Shell -Carbon steel* Surface 2: Sampling Nozzle -Carbon steel* Diameter: | Columbia, SC 29201 | ||
6.188 in.This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. | Oconee Unit 3 Relief Request 13-ON-001 3EOC-26 Limited Exam Coverage | ||
These requirements describe and are specific to scanning components in two axial and two circumferential directions. | |||
This component was scanned to the extent possible to meet these requirements. | Oconee Relief Request 13-ON-001 1.0 Scope of Relief Request Relief is requested pursuant to 10 CFR 50.55a(g)(5)(iii) for welds listed in Table 1. | ||
The aggregate coverage that was obtained is described and calculated from the following: | These welds were required to be examined in accordance with Inservice Inspection Plans for the following Units. | ||
Weld coverage using 45°, 60° & 700 shear waves for axial scans (SI, S2), and 450 & 60° shear waves for circ. scans (CW, CCW) obtained 12.3%coverage.Base material coverage using 45°, 60° & 70° shear wave for axial scans (SI) and 450 & 600 shear waves for circ, scans (CW, CCW) obtained 49.3% coverage.* 00 scan coverage obtained 29.1% coverage.* The aggregate coverage was calculated to be (12.3% + 49.3% + 29.1%)/3 = 30.2%The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is Impractical. | Oconee Nuclear Station - Unit 3 Fourth 10-Year Inservice Inspection Interval Interval Start Date: January 2, 2005 Table 1 Relief con Examination Weld ID Item/Summary Examination Reques; nit Performed Numbe Number Data Section umber (Refuelina Number Outaae) 2.0 3 3EOC26 3-PZR-WP26-1 03.1B3.110.0009 See Attachment A Pages 1-20 3.0 3 3EOC26 3-PZR-WP26-2 03.B3.110.0010 See Attachment A Pages 21-40 4.0 3 3EOC26 3-PZR-WP26-3 03.B3.110.0011 See Attachment A Pages 41-53 5.0 3 3EOC26 3-PZR-WP26-7 03.B3.110.0012 See Attachment A Pages 54-66 6.0 3 3EOC26 3-53A-15-26 03.1B9.11.0106 See Attachment A Pages 67-73 7.0 3 3EOC26 3CF-126-4 03.B9.11.0129 See Attachment A Pages 74-80 8.0 3 3EOC26 3-SGA-W69 03.C1.30.0002 See Attachment A Pages 81-96 Notes: | ||
Page 2 of 22 Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. | : 1. Duke Energy procedures require ASME Code, Section XI examinations that do not meet the requirements of Code Case N-460 to be marked "reject" for tracking purposes, regardless of whether indications were noted. Therefore, the limited exams in 13-ON-001 without indications were marked "reject" on data sheets. | ||
The achieved coverage did not meet the acceptance criteria of this Code Case.This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | : 2. Duke Energy has invoked Code Case N-663 which allows elimination of Code required surface exams for welds listed in Sections 6.0 and 7.0 of this Relief Request. | ||
No indications were recorded during this examination. | Page I of 22 | ||
The reject box is marked for internal tracking purposes of the coverage limitation only.2.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. | |||
Radiography (RT) is not a desired option because RT Is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. | Oconee Relief Request 13-ON-001 2.0 Weld # 3-PZR-WP26-1 2.1. ASME Code Component(s) Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-1, Summary Number 03.B3.110.0009, and ASME Code Class 1. | ||
The use of any other UT technique available would incur the same physical scanning limitations. | 2.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda. | ||
2.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.2.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0009 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | 2.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-l. | ||
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions.Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. | 2.4. Impracticality of Compliance Component configuration | ||
Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.Page 3 of 22 7. | " Surface 1: Shell - Carbon steel | ||
Oconee Relief Request 13-ON-001 2.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. | * Surface 2: Sampling Nozzle - Carbon steel | ||
The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006.Page 4 of 22 Oconee Relief Request 13-ON-001 3.0 Weld # 3-PZR-WP26-2 3.1. ASME Code Component(s) | * Diameter: NIA | ||
Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-2, Summary Number 03.B3.110.0010, and ASME Code Class 1.3.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda.3.3. Applicable Code Requirement | * Thickness: 6.188 in. | ||
/WB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-I. | This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), | ||
3.4. Impracticality of Compliance Component configuration" Surface 1: Shell -Carbon steel" Surface 2: Sampling Nozzle -Carbon steel* Diameter: | T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following: | ||
N/A" Thickness: | Weld coverage using 45°, 60° & 700 shear waves for axial scans (SI, S2), | ||
6.188 in.This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. | and 450 & 60° shear waves for circ. scans (CW, CCW) obtained 12.3% | ||
These requirements describe and are specific to scanning components in two axial and two circumferential directions. | coverage. | ||
This component was scanned to the extent possible to meet these requirements. | Base material coverage using 45°, 60° & 70° shear wave for axial scans (SI) and 450 & 600 shear waves for circ, scans (CW, CCW) obtained 49.3% coverage. | ||
The aggregate coverage that was obtained is described and calculated from the following: | * 00 scan coverage obtained 29.1% coverage. | ||
Weld coverage using 450, 600 & 700 shear waves for axial scans (S1, S2), and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 12.3%coverage.Base material coverage using 45*, 60° & 700 shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 49.3% coverage.* 00 scan coverage obtained 29.1% coverage.* The aggregate coverage was calculated to be (12.3% + 49.3% + 29.1%)/3 = 30.2%The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is impractical. | * The aggregate coverage was calculated to be (12.3% + 49.3% + 29.1%)/3 = 30.2% | ||
Page 5 of 22 Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. | The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is Impractical. | ||
The achieved coverage did not meet the acceptance criteria of this Code Case.This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | Page 2 of 22 | ||
No indications were recorded during this examination. | |||
The reject box is marked for internal tracking purposes of the coverage limitation only.3.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. | Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case. | ||
Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. | This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | ||
The use of any other UT technique available would incur the same physical scanning limitations. | No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only. | ||
3.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.3.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0010 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | 2.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. Radiography (RT) is not a desired option because RT Is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would incur the same physical scanning limitations. | ||
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions.Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. | 2.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014. | ||
Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.Page 6 of 22 Oconee Relief Request 13-ON-001 3.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. | 2.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0009 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda. | ||
The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006.Page 7 of 22 Oconee Relief Request 13-ON-001 4.0 Weld # 3-PZR-WP26-3 4.1. ASME Code Component(s) | The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | ||
Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-3, Summary Number 03. B3. 110.0011, and ASME Code Class 1.4.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda.4.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-l. | In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions. | ||
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds. | |||
Page 3 of 22 7. | |||
Oconee Relief Request 13-ON-001 2.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006. | |||
Page 4 of 22 | |||
Oconee Relief Request 13-ON-001 3.0 Weld # 3-PZR-WP26-2 3.1. ASME Code Component(s) Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-2, Summary Number 03.B3.110.0010, and ASME Code Class 1. | |||
3.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda. | |||
3.3. Applicable Code Requirement | |||
/WB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-I. | |||
3.4. Impracticality of Compliance Component configuration | |||
" Surface 1: Shell - Carbon steel | |||
" Surface 2: Sampling Nozzle - Carbon steel | |||
* Diameter: N/A | |||
" Thickness: 6.188 in. | |||
This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following: | |||
Weld coverage using 450, 600 & 700 shear waves for axial scans (S1, S2), | |||
and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 12.3% | |||
coverage. | |||
Base material coverage using 45*, 60° & 700 shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 49.3% coverage. | |||
* 00 scan coverage obtained 29.1% coverage. | |||
* The aggregate coverage was calculated to be (12.3% + 49.3% + 29.1%)/3 = 30.2% | |||
The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is impractical. | |||
Page 5 of 22 | |||
Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case. | |||
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | |||
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only. | |||
3.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would incur the same physical scanning limitations. | |||
3.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014. | |||
3.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0010 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda. | |||
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | |||
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions. | |||
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds. | |||
Page 6 of 22 | |||
Oconee Relief Request 13-ON-001 3.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006. | |||
Page 7 of 22 | |||
Oconee Relief Request 13-ON-001 4.0 Weld # 3-PZR-WP26-3 4.1. ASME Code Component(s) Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-3, Summary Number 03. B3. 110.0011, and ASME Code Class 1. | |||
4.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda. | |||
4.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-l. | |||
4.4. Impracticality of Compliance Component configuration | 4.4. Impracticality of Compliance Component configuration | ||
* Surface 1: Shell -Carbon steel" Surface 2: Sampling Nozzle -Carbon steel* Diameter. | * Surface 1: Shell - Carbon steel | ||
" Surface 2: Sampling Nozzle - Carbon steel | |||
6.188 in.This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. | * Diameter. NIA | ||
These requirements describe and are specific to scanning components in two axial and two circumferential directions. | " Thickness: 6.188 in. | ||
This component was scanned to the extent possible to meet these requirements. | This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following: | ||
The aggregate coverage that was obtained is described and calculated from the following: | * Weld coverage using 450 & 600 shear waves for axial scans (SI, S2), | ||
* Weld coverage using 450 & 600 shear waves for axial scans (SI, S2), and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 15.4%coverage.0 Base material coverage using 45° & 600 shear wave for axial scans (SI)and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 54.8%coverage.* 0° scan coverage obtained 33.8% coverage.* The aggregate coverage was calculated to be (15.4% + 54.8% + 33.8%)/3 = 34.7%The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is impractical. | and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 15.4% | ||
Page 8 of 22 Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. | coverage. | ||
The achieved coverage did not meet the acceptance criteria of this Code Case.This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | 0 Base material coverage using 45° & 600 shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 54.8% | ||
No indications were recorded during this examination. | coverage. | ||
The reject box is marked for internal tracking purposes of the coverage limitation only.4.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. | * 0° scan coverage obtained 33.8% coverage. | ||
Radiography (RT) is not a desired option because RT is limited In the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. | * The aggregate coverage was calculated to be (15.4% + 54.8% + 33.8%)/3 = 34.7% | ||
The use of any other UT technique available would Incur the same physical scanning limitations. | The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is impractical. | ||
4.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.4.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.63.110.0011 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | Page 8 of 22 | ||
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions.Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. | |||
Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.Page 9 of 22 Oconee Relief Request 13-ON-001 4.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. | Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case. | ||
The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006.Page 10 of 22 Oconee Relief Request 13-ON-001 5.0 Weld # 3-PZR-WP26-7 5.1. ASME Code Component(s) | This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | ||
Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-7, Summary Number 03.B3.110.0012, and ASME Code Class 1.5.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section Xl, 1998 Edition through the 2000 Addenda.5.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-I. | No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only. | ||
4.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. Radiography (RT) is not a desired option because RT is limited In the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would Incur the same physical scanning limitations. | |||
4.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014. | |||
4.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.63.110.0011 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda. | |||
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | |||
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions. | |||
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds. | |||
Page 9 of 22 | |||
Oconee Relief Request 13-ON-001 4.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006. | |||
Page 10 of 22 | |||
Oconee Relief Request 13-ON-001 5.0 Weld # 3-PZR-WP26-7 5.1. ASME Code Component(s) Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-7, Summary Number 03.B3.110.0012, and ASME Code Class 1. | |||
5.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section Xl, 1998 Edition through the 2000 Addenda. | |||
5.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-I. | |||
5.4. Impracticality of Compliance Component configuration | 5.4. Impracticality of Compliance Component configuration | ||
* Surface 1: Shell -Carbon steel* Surface 2: Sampling Nozzle -Carbon steel" Diameter: | * Surface 1: Shell - Carbon steel | ||
N/A* Thickness: | * Surface 2: Sampling Nozzle - Carbon steel | ||
6.188 in.This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. | " Diameter: N/A | ||
These requirements describe and are specific to scanning components in two axial and two circumferential directions. | * Thickness: 6.188 in. | ||
This component was scanned to the extent possible to meet these requirements. | This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following: | ||
The aggregate coverage that was obtained is described and calculated from the following: | Weld coverage using 450 & 600 shear waves for axial scans (S1, S2), | ||
Weld coverage using 450 & 600 shear waves for axial scans (S1, S2), and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 15.4%coverage.Base material coverage using 450 & 600 shear wave for axial scans (SI)and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 54.8%coverage.* 00 scan coverage obtained 33.8% coverage.* The aggregate coverage was calculated to be (15.4% + 54.8% + 33.8%)/3 = 34.7%The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to Page I! of 22 Oconee Relief Request 13-ON-001 sampling nozzle weld would have to be redesigned and replaced, which is impractical. | and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 15.4% | ||
The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. | coverage. | ||
The achieved coverage did not meet the acceptance criteria of this Code Case.This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | Base material coverage using 450 & 600 shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 54.8% | ||
No indications were recorded during this examination. | coverage. | ||
The reject box is marked for internal tracking purposes of the coverage limitation only.5.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. | * 00 scan coverage obtained 33.8% coverage. | ||
Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. | * The aggregate coverage was calculated to be (15.4% + 54.8% + 33.8%)/3 = 34.7% | ||
The use of any other UT technique available would incur the same physical scanning limitations. | The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to Page I! of 22 | ||
5.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.5.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0012 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section Xl, 1998 Edition with the 2000 Addenda.The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | |||
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions.Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. | Oconee Relief Request 13-ON-001 sampling nozzle weld would have to be redesigned and replaced, which is impractical. | ||
Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.Page 12 of 22 Oconee Relief Request 13-ON-001 5.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. | The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case. | ||
The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006.Page 13 of 22 Oconee Relief Request 13-ON-001 6.0 Weld # 3-53A-1 5-26 6.1. ASME Code Component(s) | This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | ||
Affected Unit 3 Piping Weld, Low Pressure Injection System, Pipe to Valve (3CF-11), Weld # 3-53A-15-26, Summary Number 03.B9.11.0106, and ASME Code Class 1.6.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda.6.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-J, Item Number B9.11 Figure IWB-2500-8 (c), 100% Volume Coverage of Examination Volume C-D-E-F.6.4, Impracticality of Compliance Component configuration: " Surface 1: Forged Stainless Steel Pipe" Surface 2: Cast Stainless Steel Valve* Diameter: | No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only. | ||
14.0 in.* Thickness: | 5.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would incur the same physical scanning limitations. | ||
1.250 in.This component was scanned manually with conventional methods. Scanning requirements are described in | 5.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014. | ||
These requirements describe and are specific to scanning components in two axial and two circumferential directions. | 5.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0012 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section Xl, 1998 Edition with the 2000 Addenda. | ||
This component was scanned to the extent possible to meet these requirements. | The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | ||
The aggregate coverage that was obtained is described and calculated from the following: | In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions. | ||
* 458 shear waves obtained 47.2% coverage in one axial direction ($1 -pipe)* 450 shear waves obtained 0% coverage in one axial direction (S2 -valve)* 450 shear waves obtained 50% coverage in one circ. direction (CW).* 45° shear waves obtained 50% coverage in one circ. direction (CCW).* The aggregate coverage was calculated to be (47.2% + 0% + 50% + 50%)14 = 36.8%* Best effort supplemental scanning was also performed using 600 refracted longitudinal waves for interrogation of the inner 1/3 of the wall thickness on the valve side, but is not qualified to be calculated into the above claimed coverage. | Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds. | ||
The supplemental refracted longitudinal waves were only used for interrogation in the axial direction per procedural direction. | Page 12 of 22 | ||
Supplemental scanning is not performed in the circumferential direction. | |||
Page 14 of 22 Oconee Relief Request 13-ON-001 The impracticality was caused by the taper configuration and cast stainless material of the valve which cannot be effectively interrogated by ultrasound. | Oconee Relief Request 13-ON-001 5.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006. | ||
Page 13 of 22 | |||
Oconee Relief Request 13-ON-001 6.0 Weld # 3-53A-1 5-26 6.1. ASME Code Component(s) Affected Unit 3 Piping Weld, Low Pressure Injection System, Pipe to Valve (3CF-11), | |||
Weld # 3-53A-15-26, Summary Number 03.B9.11.0106, and ASME Code Class 1. | |||
6.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda. | |||
6.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-J, Item Number B9.11 Figure IWB-2500-8 (c), 100% Volume Coverage of Examination Volume C-D-E-F. | |||
6.4, Impracticality of Compliance Component configuration: | |||
" Surface 1: Forged Stainless Steel Pipe | |||
" Surface 2: Cast Stainless Steel Valve | |||
* Diameter: 14.0 in. | |||
* Thickness: 1.250 in. | |||
This component was scanned manually with conventional methods. Scanning requirements are described in 10CFR.50.55a (b)(2)(xv)(A)(1). These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following: | |||
* 458 shear waves obtained 47.2% coverage in one axial direction | |||
($1 - pipe) | |||
* 450 shear waves obtained 0% coverage in one axial direction (S2 - valve) | |||
* 450 shear waves obtained 50% coverage in one circ. direction (CW). | |||
* 45° shear waves obtained 50% coverage in one circ. direction (CCW). | |||
* The aggregate coverage was calculated to be (47.2% + 0% + 50% + 50%)14 = 36.8% | |||
* Best effort supplemental scanning was also performed using 600 refracted longitudinal waves for interrogation of the inner 1/3 of the wall thickness on the valve side, but is not qualified to be calculated into the above claimed coverage. The supplemental refracted longitudinal waves were only used for interrogation in the axial direction per procedural direction. Supplemental scanning is not performed in the circumferential direction. | |||
Page 14 of 22 | |||
Oconee Relief Request 13-ON-001 The impracticality was caused by the taper configuration and cast stainless material of the valve which cannot be effectively interrogated by ultrasound. | |||
There are currently no examination techniques that have been qualified through Appendix VIII for examining cast stainless steel. Therefore no coverage could be obtained by scanning from the valve side. There was also a branch connection limiting the axial scan from the pipe side. In order to scan all of the volume for this weld, the valve and branch connection would have to be redesigned and replaced, which is impractical. | There are currently no examination techniques that have been qualified through Appendix VIII for examining cast stainless steel. Therefore no coverage could be obtained by scanning from the valve side. There was also a branch connection limiting the axial scan from the pipe side. In order to scan all of the volume for this weld, the valve and branch connection would have to be redesigned and replaced, which is impractical. | ||
The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. | The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. Therefore, the available coverage will not meet the acceptance criteria of this Code Case. | ||
Therefore, the available coverage will not meet the acceptance criteria of this Code Case.This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | ||
No indications were recorded during this examination. | No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only. | ||
The reject box is marked for internal tracking purposes of the coverage limitation only.6.5. Proposed Alternative and Basis for Use This weld was examined using procedures, equipment and personnel qualified in accordance with ASME Section XI, Appendix VIII. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws, and has not been qualified through performance demonstration. | 6.5. Proposed Alternative and Basis for Use This weld was examined using procedures, equipment and personnel qualified in accordance with ASME Section XI, Appendix VIII. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws, and has not been qualified through performance demonstration. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the cast stainless material. The use of any other UT technique available would incur the same physical scanning limitations. | ||
Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the cast stainless material. | 6.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014. | ||
The use of any other UT technique available would incur the same physical scanning limitations. | 6.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B9.11.0106 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda. | ||
6.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.6.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B9.11.0106 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | ||
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump monitoring ensure pressure boundary integrity by providing means to detect leakage and take prompt corrective actions.Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. | In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump monitoring ensure pressure boundary integrity by providing means to detect leakage and take prompt corrective actions. | ||
Based on the acceptable Page 15 of 22 | Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable Page 15 of 22 | ||
Oconee Relief Request 13-ON-001 results for the coverage completed by the volumetric examination, the pressure testing (V'-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.6.8 References None Page 16 of 22 Oconee Relief Request 13-ON-001 7.0 Weld # 3CF-1 26-4 7.1. ASME Code Component(s) | Oconee Relief Request 13-ON-001 results for the coverage completed by the volumetric examination, the pressure testing (V'-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds. | ||
Affected Unit 3 Piping Weld, Low Pressure Injection System, Pipe to Valve 3CF-14, Weld# 3CF-126-4, Summary Number 03.B9.11.0129, and ASME Code Class 1.7.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda.7.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-J, Item Number B9.11, Figure IWB-2500-8 (c), 100% Volume Coverage of Examination Volume C-D-E-F.7.4. Impracticality of Compliance Component configuration: | 6.8 References None Page 16 of 22 | ||
* Surface 1: Cast Stainless Steel Valve* Surface 2: Forged Stainless Steel Pipe* Diameter: | |||
14.0 in.* Thickness: | Oconee Relief Request 13-ON-001 7.0 Weld # 3CF-1 26-4 7.1. ASME Code Component(s) Affected Unit 3 Piping Weld, Low Pressure Injection System, Pipe to Valve 3CF-14, Weld | ||
1.250 in.This component was scanned manually with conventional methods. Scanning requirements are described in 10CFR.50.55a (b)(2)(xv)(A)(1). | # 3CF-126-4, Summary Number 03.B9.11.0129, and ASME Code Class 1. | ||
These requirements describe and are specific to scanning components in two axial and two circumferential directions. | 7.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda. | ||
This component was scanned to the extent possible to meet these requirements. | 7.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-J, Item Number B9.11, Figure IWB-2500-8 (c), 100% Volume Coverage of Examination Volume C-D-E-F. | ||
The aggregate coverage that was obtained is described and calculated from the following: | 7.4. Impracticality of Compliance Component configuration: | ||
* 45* shear waves obtained 0% coverage in one axial direction (S1 -valve)450 shear waves obtained 50% coverage in one axial direction (S2 -pipe)* 450 shear waves obtained 50% coverage in one circ. direction (CW).* 450 shear waves obtained 50% coverage in one circ. direction (CCW).* The aggregate coverage was calculated to be (0% + 50% + 50% + 50%)/4 = 37.5%* Best effort supplemental scanning was also performed using 600 refracted longitudinal waves for interrogation of the inner 1/3 of the wall thickness on the valve side, but is not qualified to be calculated into the above claimed coverage. | * Surface 1: Cast Stainless Steel Valve | ||
The supplemental refracted longitudinal waves were only used for interrogation in the axial direction per procedural direction. | * Surface 2: Forged Stainless Steel Pipe | ||
Supplemental scanning is not performed in the circumferential direction. | * Diameter: 14.0 in. | ||
Page 17 of 22... ....... .. .............. | * Thickness: 1.250 in. | ||
......... -- ..... .. .. ... .. .... ..... ..... | This component was scanned manually with conventional methods. Scanning requirements are described in 10CFR.50.55a (b)(2)(xv)(A)(1). These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following: | ||
* 45* shear waves obtained 0% coverage in one axial direction (S1 - valve) 450 shear waves obtained 50% coverage in one axial direction (S2 - pipe) | |||
* 450 shear waves obtained 50% coverage in one circ. direction (CW). | |||
* 450 shear waves obtained 50% coverage in one circ. direction (CCW). | |||
* The aggregate coverage was calculated to be (0% + 50% + 50% + 50%)/4 = 37.5% | |||
* Best effort supplemental scanning was also performed using 600 refracted longitudinal waves for interrogation of the inner 1/3 of the wall thickness on the valve side, but is not qualified to be calculated into the above claimed coverage. The supplemental refracted longitudinal waves were only used for interrogation in the axial direction per procedural direction. Supplemental scanning is not performed in the circumferential direction. | |||
Page 17 of 22 | |||
.... . . .... .. . .............. . . . . . . .. -- . . ... .. .. ... .. . ... . . ... . . . .. . .. ...-. . . . . . I | |||
Oconee Relief Request 13-ON-001 The impracticality was caused by the taper configuration and cast stainless material of the valve which cannot be effectively interrogated by ultrasound. | Oconee Relief Request 13-ON-001 The impracticality was caused by the taper configuration and cast stainless material of the valve which cannot be effectively interrogated by ultrasound. | ||
There are currently no examination techniques that have been qualified through Appendix VIII for examining cast stainless steel. Therefore no coverage could be obtained by scanning from the valve side. In order to scan all of the volume for this weld, the valve would have to be redesigned and replaced, which is impractical. | There are currently no examination techniques that have been qualified through Appendix VIII for examining cast stainless steel. Therefore no coverage could be obtained by scanning from the valve side. In order to scan all of the volume for this weld, the valve would have to be redesigned and replaced, which is impractical. | ||
The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. Therefore, the available coverage will not meet the acceptance criteria of this Code Case. | |||
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied. | |||
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only. | |||
7.5. Proposed Alternative and Basis for Use This weld was examined using procedures, equipment and personnel qualified in accordance with ASME Section XI, Appendix VIII. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws, and has not been qualified through performance demonstration. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the cast stainless material. The use of any other UT technique available would incur the same physical scanning limitations. | |||
7.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014. | |||
7.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B9.11.0129 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda. | |||
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity. | |||
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump monitoring ensure pressure boundary integrity by providing means to detect leakage and take prompt corrective actions. | |||
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable Page 18 of 22 | |||
Oconee Relief Request 13-ON-001 results for the coverage completed by the volumetric examination, the pressure testing (V'-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds. | |||
7.8 References None Page 19 of 22 | |||
........................................................ 71 | |||
Oconee Relief Request 13-ON-001 8.0 Weld # 3-SGA-W69 8.1. ASME Code Component(s) Affected Unit 3 Steam Generator A, Feedwater System, Tubesheet to Shell Weld | |||
# 3-SGA-W69 Summary Number 03.C1 .30.0002, and ASME Code Class 2. | |||
8.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section XI, 1998 Edition through the 2000 Addenda. | |||
8.3. Applicable Code Requirement IWC-2500, Table IWC-2500-1, Examination Category C-A, Item Number C1.30, Fig. IWC-2500-2, 100% Volume Coverage of Examination Volume E-F-G-H 8.4. Impracticality of Compliance Component configuration: | |||
* Surface 1: Shell - Carbon steel | |||
* Surface 2: Tubesheet - Carbon steel | |||
* Diameter: 148 in. | |||
* Thickness: 5.125 in. | |||
This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), | |||
T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following: | |||
" Near Surface coverage using 600 shear waves for axial scans (S1, S2), | |||
and 600 shear waves for circ. scans (CW, CCW) obtained 73.1% | |||
coverage | |||
" Weld coverage using 35c, 450 & 600 shear waves for axial scans (S1, $2), | |||
and 45' & 600 shear waves for circ. scans (CW, CCW) obtained 75.7% | |||
coverage. | |||
* Base material coverage using 35°, 45°& 60° shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 80.6% coverage. | |||
* 00 scan coverage obtained 73.1% coverage. | |||
" The aggregate coverage was calculated to be (73.1% + 75.7% + 80.6%+ 73.1)/4 = 75.6%. | |||
The impracticality was caused by four lateral restraints that did not allow scanning from the Surface 1, CW and CCW direction, and allowed only partial scanning from the Surface 2 direction. In order to scan all of the required volume Page 20 of 22 | |||
== Description:== | == Description:== | ||
.kqu to Shin System1 : 5O.. | |||
C*mponent-1.: IO 3 MW ,2,-7 Skae/Lnbth N/A a C81.1651 NA Uimittons: -Yos | |||
* see attached seet FiihTime: 1!225 1165 Finish Time: lZis Start Time: | |||
lastitament Setting. Seria No.: Search unit Axial Orltitatad Search Unit. | |||
Serial No.:; OOTdT N.:OIR93H Seia -ChecJ Cle~n Sga Sweep Path MunUfaCt..r. KRAUTKRAMER ManUkCbAurs KBA Md jCalIW .hV12, Reflector Aiplilbide % Divison | |||
*:.. M.d.l:USH.40 Si*e: .5x1.0 Shape:" L!! 1i" Cal.. ": E"Z. . o 1.00-12.0 Delay 14.0744 Range: 50 Preq.: 2.25 MHz Style: G"mma C&L 120 .419=2 1.0 70 4.0 2.0" | |||
.. .:...:,. V. k .16: Pu.sen High Exam Angle: 60 Sof Wamenji: ingia 1.5 a6 6.0 3.0"** | |||
0amp~g~. 1 Roj .0% Mode: Sheai ia a 13540'4/19/W20 2.0 40 U 4.0" Re.at: Autahigh. Freq.: 2.25 MHz Measured AMr , s - Coupaiat" Sla4r so 7.0 .s.* | |||
* ftrFixed: Mode: PE Wedge St ows C.l. Bateh 11225 ClraumferentW Orientated Search Unit Votae: fixed Othen Fuliwave: Type: ULTRAGEL- Calibration Silnl Sweep Search Unit Cable M.: Sonoticb Reflleto Amplikide Division Son h ON.~4~ .3 lM of Sound Path Te RO., . -, Exam B 41225 See~x Linearity port No.: L-124200 Lengh: *.." . No. Conn.."...-. .. Type: '.ULRI, LIi | |||
-Calibration Bl1ock Scan Coverage Mfg.; "" ontschi Block.-No. | |||
.Ca...ream .03. " U (J Deebeam | |||
" SCnW : 70.5- Rel,,n. ,loc RIieta ee/mulaaor Bock" | |||
. Icknes:.s 7 Di.: Fliat "CCW. Scand*,: 70.5 Gain Sia Se unPa SWNo.: 96452 Cal. 8ik. Temp;.; 70 Temp. Took: .MCNDEd40128 | |||
:.: :.-..,:* * .,* .:o]..- '... Exam".. | |||
.;: ---": ........- B*Ofao. ;" | |||
Type: ."- A_ | |||
RO IEPAS | |||
.dB Reflector. ~deV. Divison Camp | |||
.;. Temp. Temp. Tom 1 M:...NDE41a1Z. Surice Condition | |||
* As m,,und . S9A IrRadwsa so 4.2 .1 2.00" Recordable 16dc (s): yeas : o - (IfYe..*.R*ef uacadUltramac.Wnn*.Repo).. | |||
L. | |||
A"ccep | |||
.tala 0 Rej*ct. .2 Into [3. Comments: N/i Perpent 01, Coverage Obtained 90% | |||
M No Reviewed Previoua Data: Yes | |||
.... jJ .II; | |||
.... III* 7777 lure A f P | |||
.. :... ,. . .w i i!*N :::: -::i.: . . ..IA.*..:: . .; I::i;:i:* | |||
-,b 1:.. | |||
C.!".. | |||
[ O | |||
.:::.:~~~~~~~~~~~~~~ | |||
th e | |||
"...* .7..: : ........ AT TACO NEITA? | |||
?A6E *'r?Df 96, | |||
. | UT Calibratiorcamina | ||
* ND941= Outage No.: 03-218 Summ ary No.: 03.93&11O.002 kwwmeaw Rev.:- 7 Report No.: UTl4245 Work OrderW.: 01911420 Page: 3 of .'11 III Cod 11.912006A . Ca/Iutem: 3. | |||
-B-p1113.110 wingNo.:2: | |||
noia I. -CNo 0 Deacaptdoe N6=l. to $hell System ID: '50 C...ompnnt .:.....WP26 " StmaLapp: WA ThiclneaaOlarnater. C8.1 6.1881 NA Umnitalmon.: Yes - See ,Otsed ,,heet " Stait l imte: 1155 Finish Time: 12'25 I | |||
.u.e.. SetiG.s Search Un - - | |||
Sea. No.: o0TJXr Seral No.: 01PR.N.. Chec I " Axa Orwe!Atd Slearch Unit Caibrellon Signal Swep ound Path Manustcwuate KRAUTKRAMR.R Manudatkfrw KA.- inIU C31 '1035 4119120 Reolecr Ampliude 1 OlvIalon Moe:UN0Sies: _:=* s. *o | |||
.. | .Sxl.0 P: | ||
Shape:* , | |||
Rqe. hiker Cal Intr Cal.* 111 .111 In 80so 1.2 3A- | |||
"" ": .-14.0744 Range:. 2.0" Fmq. 2.6 MHz Style:, m 218 30 2.A ,s. | |||
An CaIWal: .1268 Pulaer~ High Exam Angle: so #of EmmdLunne.Unl Cl- | |||
.. .- 0% | |||
: | .Rject -11 C 13381 319 20 4.0 U." | ||
. | ________ Mode:____ Shear Rep. Rate: Aut-high Freq.: 225 MHz Measu.*d Angle'.O '. 0 ." Notch so5 00 is 6.0 7I 12.10"' | ||
16.8-Ftitat Fixed Mode: PE wed" StylS CaL Oatd 1111225 Ctemm~rmvs sOrtstatsd Search Unit I Vo taigoe: Fixed OtheW. Fuliw*ve . Type: ULTRAOnLI. L_ | |||
Sweep Ax. Gain (fd) 54.5 Crim Gain (dB 4.5"S Search Unit Cable. MW.: Semol.,, Reflector Amnlikude 1A OIVlSon Iound'Path t 9-ta I ScrenDiv.,..i.:;.":::Ex 2i In.of Sound Path Type: RG-174 """"225 Fxm S... lo" 11225 WA | |||
. | :i.ea"L tyReport No.: WL12-200 LenIlh 6 No. C " 0 Type: ULTRAGEL II | ||
-i~on e, Sean Coverage Mg.-: Sonee.'h' CaL Block No. 40338 UpatreamnQ DowMMstrem 60*9 nCI: 1.5 "" Refemancefflmulator Sleek Thickness 7 Die.: Flat CW & CCW0 Sewn d: 6-.5...s* ._ _ _ | |||
.".. Slt. Temp. remp.Tool T0 . MCNDE4OI2" Exrn Suitaee 0.D. Ty: ROMPAS a eletrAmpfltde % iiio Comp. Temp. 80 Temp.Tool MCNM540120. Surfac Conditlon: As ,out'"d so I 8 I Z IW 2iI Recordabli ndical"on(s): Y- Q No J (itYea. Ref. Atted Ultrasonic ,-dI*k=a Report) | |||
.9 20j a jus Res". | |||
.info | |||
. Accept Q Re"e [3. C.mmnbt A, " | |||
Percent Coverage P Obtained 90: No Rvwed Previous Data: | |||
E1aminer6 ei | |||
,.G41 ture ... . .gna Y"e DafaI R o Mj L./I | |||
*.. :. :.:,.:. * ... .. 4.. AITACH NEEMI/# | |||
MAE-59 If., | |||
% | U DUKE POWER COMPANY IS. LIMTATION REPORT Component.Weld ID: 3-PZR-WP26-7 Item No: 03B3.110.0012 remarks: | ||
.... 0NOEAG SCAN SURFACE0S.6.: BEAM.DIRECTtON DEG Due to nozzle cpnfluration. | |||
LIUMITED SCAN C0 1 0 2 I020cw 0 cow "FO L N/A. to L N/A INCHES FROM WO Too to -Beyond. | |||
ANGE: 00 45 0.60 other 6OS FROM'_0 DEG to38 DG O1..NO S.CAN SURFACE BEAM DIRECTION UMIMED SCAN 0 1 .0 2 I E 2 ow 0 ccw. | |||
. | FTROM L :___toI____ INCHES FROM W6 ____ to ___ __________ | ||
ANGLE..: 00 45 060 other F.ROM DGto DEG 0' ASCANNO SURFACE BEAM DIRECTION | |||
.. . | -LIMITEDSCAN .0 1 [1 2 .0 1 02.'[ Cw [Icw c FROM. L NIA to LN INCHES FROM WO to .,_od ANGLE: 0 0 0 45. 60 Other FROM DEG to -. DEG SINO SCAN SURFACE BEAM DIRECTION 00 060 *other DE_ | ||
.OLIMITEDSCAN 1 0 0 2. 20 cw.)ccw UT-12.62 IFROM L: _ _to L INCHES FROM WO " _ to Sketch(s)attached ANQGLE: Q:OO0 6 060 other FROM -DEGto DEG 0 A:PrepareB o11 DOW 04/10/12 Sheet 4 of X.ReviewedyN SAN Date: AM DECTins Q | |||
%j ATTACHMENTI " | |||
PA6*E ofBF | |||
iteimNo.:-03M.B3.1*OJ012 Prer Sampling Nozzle to Shell 0 | |||
:,Weid No. P26-7: sca lan. | |||
Nozzle Surface,2 Base Ml- &mied with 600, 60oNS and 450 as. | |||
I 600, 60ONS mid 45oCirc. | |||
" ' 3.1" | |||
:Shell Surff=e 1 | |||
* .- .. . , 1 1 ý 1 ATTACHNENTI 2e.*LT~ ~ 2' MAEýo OF Y&i | |||
Pressurizer 4S ing .Nozzle to ShelI 450& 600 | |||
..* . ... "O-0B3.UO.O.1-Scan.Plan WeldiNo..3-P.RW*26-7 Surfaw st Measured fm OD of Nozzle . F Nozzle | |||
.TotalArea Coverage %xaminedwith at least 2 angles from one direution.. LA, z-I A.cminto of 450 ,60& 60WNS angles vwe ued to obtain a Mamum amout of coverage. | |||
I 16.88" | |||
:I A1I" 1 450 | |||
-. 60 i...!:..4::::i. | |||
*urfac 1 ATTACHNEN IA-FA6EV( OF | |||
Items No.: 03.B311O0.0012 Pressurizer Saling No4etoShell | |||
ý:.Wel No.: WP26-7 Nozzle Total Weld Metal Examined with at least 2 nges from one direction. Surface 2 A combination of 45' and 600 angles were usedto obtain coverage. | |||
%Examined from Surface 1=7,015/ 11.413X 100=61,46%/." | |||
%Examined from SurfaceCW, and CCW- 0K. | |||
60P 450: | |||
K: | |||
I | |||
..Shell Surface 1 X N X X N X N X X X X % N'N" 1. 11 "Ill,% 11"N 1ý 11 I-7.015.s-Sin P4 . : -7* | |||
0o MW OZf~Ite | |||
ItemýpN............... *zr Slliflpliflg0NOZii* | |||
Pressuzer to Shell WeidNo.: WP267 .... | |||
Nozzle | |||
,-:, ,,,,, ,Total Base Metal Examined with at least 2 angles from one diSfonae A combination of 450 and 600 angles wee used to obtain covepe. | |||
%Examined = (24.45 + 5.705) / 44.87 x 100 = 67.2. | |||
? :::: i/ ..... | |||
___ 24.45 sq. in. | |||
ii ~~~~~H 45:0i:.: | |||
*T.T \.N N TTT 7N 5.705 *sq 4.. | |||
.. 2.. Prsudzer SaplngNoizl to SheIl 0 i" .. WeldNo. WP26-7 Base Metal Exmined wvith 600O and 450 ngldes. | |||
%Examined WOandl 450 19.03 /44.87 x, 100-= 42.4%. | |||
600nd45O~im scan 19.03 sq. in. | |||
Surface 1 11 NNN 1 X N X XXX XXýk 'INN XXXý1 XXIN | |||
"'I XXX'IN XXX | |||
'IN X -XX XXý | |||
'~G~Td 4 Wt12 A~L. | |||
TIACUMEIT k 0 PAl 9',. | |||
z o I e4No.1 3.B3M.11O.0012. | |||
Pessurizr P u..... | |||
N Sa*pf.Nozzle to Shell 9. | |||
Weld No. : VP26-7 | |||
.Base and Weld Metl- Examined with 00 angle.. | |||
%ExaminedO0 = 19.03/ 56.283 x 100 =33.ý/o.. | |||
19.03 sq. in. | |||
.. l : | |||
*Shell | |||
.. r: c .1..".,.,'. | |||
T T T IC\ -7 T KT | |||
* ~TTACIIKEMT k 2arOO1 95. | |||
PAIE~~5DF9~~ | |||
.PZRSamvlinif Nozzle to Shell %.of Coverage Item No.: 03.B3.110.0012 Weld No,: WP26-7 S.:: | |||
Sd~ | |||
Weld Coverage | |||
.~ | |||
Scan Aniefe % Coverage Obtained 0-Si 450 & 600 61.46 .~ a. | |||
S2. 450 & 600 0. | |||
Cw.. 450 & 600 .0 CCw 450 & 600 0 | |||
.*. . Total 61.46. | |||
15.4 61.46 -4= % Coverage Base Material Coverage | |||
. 2 I~c.* 450. & 600 | |||
.450 & 600 67.2. | |||
42.4 ToWal 109.6 109.6 + 2 = 54.8 % Coverage 00 Scan Coverage 33.8 % Coverage Aggregate Coverage = Weld + Base Material + 00 + 3 34.7 % Coverage Pag 2. | |||
nspector/Date | |||
. . . Page IL of l_*I. | |||
.-.... .' S. | |||
UT Calibratioamination ocon.. I 3 Procedure- PDI-UT-2 Outage No.: 03-20 Summary No.:: | |||
o3.B9.11i.01o6 Procedure Rev,: .E Rieort No.: UT-12463 i:*:!.*.:!: | |||
,iW :; | |||
* orkeco. | |||
181I Work Order No.: | |||
0195 Page: 1 of 7 CodeI 19082006A Catjitem: I4 /B9.11 Location: | |||
. rawin. No.' 34.*A-1 (1) | |||
== Description:== | == Description:== | ||
Pipe to Valve 3CF.11 System 1D: 53A Component ID: 3463A-1 $45 Size*gt: NIA ThicknesslDlameter. 88 11.250 114.0 U.. ita.. tio.. | |||
.... : Y*.. d sheet Start Time: 090 Filah Time: 1009 instruMent Settings Seatrh Unit AxIal Orteztatmd Search Unit Serial No.. 0242D3 Selal No.: OFtTJO Ch*Gks CaEIbrtion Signal Sweep Sound Path Manufacture. A-Ma-lacturer. KBA It Cal 0.40 4M -12 Reflector Amplitude % ODvlon Model: UsN40oSW $Sze: .5 Shape: Round i ., 1.2r Notch o 1.737 1ela y:- | |||
. Ir:::*i~~ . .0041 Range: .3.0" Fre,*- 225*. | |||
Frlq.. M; Style ComAp -*a*:*... jn 0.. 0ON6 412712012 | |||
:::i:: 2.251 Mz Style: Intr MCae: .1218: Pulser SqIuam Exam Anl: 45 # of Elerments: Single -inter. Cal.I ihl~n:: 5:00 Reject: 0% Mode: S1hear R.ep. | |||
. R , | |||
110er otge Aut*oht Fixed | |||
-40 F.M. | |||
Mode: | |||
Otfier. | |||
2.25 MHz PE. | |||
Fulkwave Measured Angle: | |||
Wedge Se: MSWQC 45 Cal. Bech Type; 11228 ULTRARIEL II i Circumferential Orientated Search Unit Cesibwaon signal Sweep A'..Gin 12.2 C(dB)Gain (dB):' | |||
Cic. 12.3 Search UnItCable Mill Sontec Reflector Anipilud % Divsion SonPa i Scen.i:.:.6 Dv.u - .3 In.of Sound Path Type: RG-174 Exam Batch 11225 See Axial Uneasily Reipo No.: L42-193 Len.th V ft Camt.. | |||
Soon Coverage 0 Type: | |||
Mfg.: | |||
ULTRAGEL , | |||
s"notee , | |||
I I I C.allbratlon Black CeE;Block No... P y-uA-O Uparew Q Downstream 1 Scan d: M R4ferc Bac3k Rferencel/1mulator Block Thlckness:* ..,37 -1.28" eDi.: Flat OW 0 CCW [ Scan dB: 24.3 Serial No.: 044743 d, AI Ampliud %Dison Refltor e | |||
*...CaL.8.lkLTemp...._ .Temp.3Tool: - .MCMDE40.1i2. _Exam.,u :_ _0J)._T . MP | |||
:Conq. Temp. so Temp. Tool: .MCtDE401ZS Suface Conditlon: As Ground R dable Indication(s): | |||
i.c: Yes Q No (IfYe Ra. Attached Ultrasonic Indletion Reope.) | |||
:Rasuts Accept Q Reject Ea Info ] Commens: PulIae Width 220 ns ill $e11on X) Exam | |||
:.--pentOf ove`Pge.Q4t4lned "90%: No " Revlewed Previous Data: No Ejoa**ý:': Level IýN Date Rovisow onto | |||
,.Day.J, 412712012 Level. 041 Date am Signature Date Steven V27IM2 Other Level WA Date RA 0829 14A ATTACHNNEJ,4-PAGEOF 96 | |||
UT Calibratilliamination | |||
" SiteJUnlt Oconee 1 3 Procedure: PDI4T-2 Outage No.: 0-.26 | |||
+:' :..:;.* .:.:. | |||
* Summary No.: Procedure Rev.: E Report No.: UT-12-963 | |||
. .:.: ... ; Wod.woope: IS! Work Order No.: .01955830 Page: 2 of 7 Cod. 1998r2000A CaiJItAm: 9-J 199.11 Location: | |||
aingo.: 3.A5 I) | |||
9-J 199.11 Location: aingo.: 3.A5 I) | |||
== Description:== | == Description:== | ||
pipe to Volvo 3CF.11 | |||
:Syftem ID: 53A Component ID: 341WSS15-26 Slzung: NIA ThknesalDIameter 5 11.250114.0 Umbltalona: Yea - see attached sheet . . . . .. .a.... I.. StaitTime: 1011 Finish Time: 1031 Search Unit Serlli No.: | |||
sinstrumant Sefttig 024213 Serial No.: 03-782 CaL Check I I Axil Olenlated Search Unit | |||
.. nufa .;u . . KRAUTKRAMER Manufacturer. RTD initialCal Model: USN,,60 SW Size.: 2(1!02) Shape: Rec, Inter. Cal. | |||
Do*a 12.0647 Rtange: 4.0 Freq.: 2.0 MHZ Style: IRL2 IMh Cal:ýitIZ4 Puter. SqUISTe .yam Angle: o #QofElementa. Dual Dampfing .00 IRjec11t . 1 Mode: Long. | |||
Rep. Rate:, Autohlgh Freq.: 2 MHz Measured Angle: 50 couplent Filter... PFled.' Mode: Dual Wedpe Style: Integral C.1. Batch: 11226 ClOcumfreindal Ordentated Search Unit oltage: 450 Other. Fulwa"ve. T, ULTRAGELU | |||
,pe: Calbration Signal Swee Sn | |||
-AX.Gah(dS) 51.3 Crc. Gain.(d) MIA Search Unit cable tfg.: Sonoatch Reflector Ampltude % Divlion WA | |||
: I $Green DIV. .4 W of Sound Path Type: RG. 174 xam Batch 11225 ea. l. | |||
* ::i:... ... No.:*.L*-L2-193 , i.li. No. Conn.- Type: ULTrAOEL 0 Celftration Block scaw Coverageh W: Sonotech Cat.":locic No. PDl-rT-TA-.O Upstream F] Downstrem a Scan dB: 54.0 Referanae Block Reframncelflnmulator Block Th-:i.ickn .37V 1.215 D-.. Fta Cw ] CCWO Scan dB: NIA werdl No. 04-8743 Gain ... Signwal Sweep Sound Path dB Reflector Ampitude % Division Ca-L9o Te*.T*.17. Temp. Tool: MCNIDEA412. Ewmn.S0we O.D.. rye: R*MPAS 4 - lRRIkii 1 -6 2:5- -1 0-Comp. Temp. 69. Temp. Tool: MCNDE40128 Surface ConldIonm . AsGround Recordable indicatlo,(s): Yes Q No Ea (If Yes. Ref. Attached Ultrasonic Indicatlon ReporLt.) | |||
Results: AcceptQ0 Reject~ 0Info Q Comments: Pulse Width: 250 ne initial Section )U Exam P.eretOf Coverage ObtAIned v 00%: No Reviewed Previous Data: No i | |||
ATTACIHEIT/ | |||
MAEa OF ?W, | |||
F: slteunit.. Oconie .. 3 UT( amination Procedure: NDE4-40 Outage No.: | |||
9 03-26 11.0106: | |||
summrayNo.: :03.1119. Prooedure Rev.: 010653 Report No.: UT-12-063 SI 0155 Workscope: Work Order No.: Page: 3 of 7 | |||
:Cod*:: : :- 1998000A CatLtem: B-J 139.11 Locatw. | |||
Drawing No.:. 3-63A15 (1) Doescption: Pipe to Valve 3CF-Il System ID: 5. . | |||
Component ID:b: 3411-1-2S6 slze,*,,h: MIA ThicknessDlameter 88 11.250114.0 umitalons:: Nome Stan Time: 0936 Finish Time: 0946 | |||
- ,. - I - I I~ | |||
InturuentM Settings; search unit cal Time bhUnit Date Axial Orientated Be SerWa No.: 024203 Serial No.: 57452-08724 Checks So Calibration Signal Swoop und Path M: wfdactuemr KRAITKRAMER Manufgctmr. KIA iM Cal 0935 4127/2I Reflector Amplitude % Division Mode,: *usN-40 SW Sie: S.MXComm Shape: Round foer. Cal. so 8W 6.1 1,23= | |||
9.i5 Rage... .2.0 Freq.: 4.0 MHz Stle: USES nter. Cal. | |||
* .MCVl.a. .2m0.. Pulser. square Exam Ang* .0 Sof Elamentso: Dual nar. CaL._" | |||
Dom1n: 5i0so: Reject: | |||
*0%* Mode: Long.. IaCcl 09471 4/=2/2 Rep. Rate:-:. Autjlilgh Freq.. .4 Mliz Me asured Angle: 0 Couplnnt F-tr...: Fixed Mode: Dual . Wedge Style: Integral C ai. Batch: 11225 Choumferential Orientated Search Unit Voltage: .450 Other: FultwaveT Yoe: ULTRAGEL I Caibratlon SIgnal Sweep ft Pt Ax.Gan (dB):-. .46.6. C Galn (dS): 46.6 bearch Unit Cable b us.: sonoteob Refle*to AmplWAIde % DivIsion Path een Div. la A"* I of Sound Path Type: RO..14E yzom Batch 11225 Unez eptNo.: L-..2-.,3 : *L,,igth: r No. Con.- 0 rype: ULTRAGEL il | |||
.a'labratIon Block.. Scn Coverage 4U: Sonotech CO. 8l.. ... No.. Component Upstrea Do.wstream 9 Scan dB: 40.6 Referencs Black Reforonce/Slmulatar Block | |||
*Thickness 125. DIa.: 14 CW 9 CCW Scan dB: 4.66 | |||
;erial No.: 044743 Gain SII %I Sweep I Sound Path dB I Retcleco 1AMD11JUde % Division | |||
*.Ccl.:81.Temp,. 77 Temp. Tool: MCNDE40128 Exam Surfac .0.D. 1 Camp. Temp. 63 Temp. Tool: UCND0140128 Surface Condition: As Ground rypo: ROMPAS 416"jW j | |||
-Recordable lndicatiorgs): Yes Q) Moe (if Yes. Rot, Attached Ultrasonic Indlicetion Reporl.) | |||
Reaulte: Accept Reject C Info 0 Comments: Initial Section Xl Exam PercenItOfCoverneg Obtalned 90%: Yes Reviewed Previous Data: No ATTACHNMINT A PA6E6.of OF? (o | |||
0 DUKE POWER COMPANY ISI LIMITATION REPORT Component/Weld ID: 3-53A-15-26 Item No: 03.119.11.0106 remarks: | |||
/ NO SCAN SURFACE BEAM DIRECTION No scan due to cast valve | |||
:E3 LIMITED SCAN 3 1 0 2 0 1 IC 2 N cw 0 cmw configuration. | |||
*FROM L N/A to L N/A INCHES FROM WO CL to Beyond ANGLE: 000 45 060 other FROM 0 DEGto 360 DEG 0 NO.SCAN SURFACE BEAM DIRECTION No scan due to location of | |||
:o I"UMITEDSCAN [0 11 02 [11 ( 2 C3 w D ccw Pipebranch. | |||
FROM L 4.0 to L 6.5 INCHES FROM WO 1.5" to Beyond ANGLE: Q 0 0 45 . 60 other FROM N/A DEGto N/A DEG o0 NO SCAN SURFACE BEAM DIRECTION E" LIMITEDSCAN 1 02 1 0 2O 0 cwC3 __w FROM L. to L INCHES FROM WO to ANGLE: 0 0 E] 45 0 60 other FROM - DEG to DEG | |||
: 0. NOSCAN SURFACE BEAM DIRECTION I IIII IBI o0 -UMITED SCAN r"1 I1 2 0 1 02 0ew 0ccw LUT.12-963 FROM L to L NCHES FROM WO _____ _____to _ _ _ _ _ | |||
Sketch(s) attached 4 D No | |||
.ANGLE: 000[ 5[106 ther FROM DEG to DEG 23 yes Pre.pared W Steve 04/27112 I Sheet 4 of 7 | |||
*Dat: | |||
q.~5.1 .. Authorized Inspector Date: | |||
ATTACHMENT Aq-OýZAe ~~M OAF(,, | |||
Suppler&I Report Report No.: 4 9 6 3 Page: 5 of 7 Summary No.: 03.69.11.0106 Examiner: Day, John. C. Level: I1-N Revlewlr: | |||
:Examiner. Dean, Steven Level: iI-N Site Review Z2/21 Date, Date: | |||
Other NIA Level: NIA ANII Review. | |||
Clom ments: Praoil for wed o3.53A-161-Sketch or Photo: | |||
L ATTACHMENT A PAIE7(IDF 716 | |||
ReportReport No.: | |||
Report: U 01-63 page: | |||
6 of 7 Summary.No.: 03.B9.11.4106 Examiner. Day, John, C. LeveL I14-N Reviewer Date: I Examiner Dean, Steven Level: "lN Site Review: 0 A1 Date: ____ | |||
Other NIA Level: WA ANII Review: Date: | |||
Comments: CoverageP t for weld 3463A-15-26. | |||
Sketch or Photo: | |||
ct-rcLuire46Cca t44-eY e | |||
2 .s/qq'xioo:S4_ , MS~ c1ve(4 ATTACHMENT / | |||
MAE 1-OF9~ | |||
Site/Unit Oconee I 3 Determination of Percent Coverage fo UT Examinations - Pipe i Procedure: PDI-UT-2 i r | |||
Outage No.: 03-25! | |||
I", | |||
40 Summary No.: 03.69.11.0106 Procedure Rev.: E Report No.: UT-,124-3 . 91. | |||
Workscope: I51 Work Order No.: 01965830 Page: 7 of 7 45S Scan 1 94.400 % Length X 50.000 % volume oflength 1100 47.200 % otal for can Scan 2 100.000 % Length X 0.000 % volme of length 10, 0.000 % total for Scan 2 Scan 3 100.000 % Length X 50.000 % volume of length / 101 50.000 % total for Scan 3 Scan 4 100.000 % Length X 50.000 % volurie of length I 0i . 50.000 % total for Scan 4 Add totals and divide by# scans 36.800 %totallfor4l deg (to be used for supplemental scans) | |||
The data to be listed below Is for coverage that was not obtained with the 45 deg sca.s Scan I % Length X _________ %volume | |||
% of length 1100 = _____ % totail for Scan I Scan 2 % Length X _______% %volume of length /100 a " total for Scan 2 Scan 3 % Length X _________ %volume | |||
% ofienglhlt u __1__0__= " total for Scan 3 Scan 4 %Length X _________%volumeoflength/100=______ " total for Scan 4 Percent comnilete coveram Add totals for each scan required and divide by # of scans to determine; | |||
. 36.800 % Total for complete exam Site Field Supervisor:. Date: | |||
I | |||
£i*I I,,i,,,,,, i ,i,, 7,, ,, l~)% 4 (pt. | |||
UT Calibratioiamination Outage No.: 0, | |||
.Oconee .. I .3 Procedure: *P01-UT-I Summary No.: 03.641.11.012 9 Procedum Rev. ik dN I.: | |||
r.T124*1 Woftccope: Work Order No.: 01958382 Page: 1 of 7 Code: 199112000A CLit~lem: B-J A119.11 Loectiace | |||
.Dmwng No.: 3CF-126 DeascrptIon: Pipe to VIve 30F-14 System ID:m S | |||
:.Compone.. ID:. | |||
. 3C. 2.. WA Thcknessa/Dieter: So I s.2 114.0 U~mitedona: Yes- 3eeAtached sheet S*tTime: 111I Finish Tlme 1200 | |||
:.:In..a. | |||
... w:..".t Seulnge Sewch Unit Sole!* No.: oO pl SeOWe No.: 8E0355 Ue niilerure,. GE Manufacturer GE Model: USN I0 8W Sie: . Shap Round | |||
. P W* - Range:.. Freq.: 2.25 MHz Style: Camp -aG Mu CAI .A1. 5 Puller S.quar 22mm Angle: 45 #o! Elementa: single | |||
: amp :i 00 :Rejc o0% Mode: shear Rep. Rate: Auatchlihl Freq 2.25 MHz Measud Angle: 4*S CoupIant* | |||
Fil:, Piked Modw. PE Wed"e Stwe: MSW4IC CadL Batoht 11225 Clrmmerentlal Orlienated Search Unit Voftw : 45.0 Oew. Fuhwave Type: ULTRAGEL II Cabeuflon sognl Sweep Sound Path Ax. Gal.(dB) . ISA. -hv. Gain (B):. I"A Search Unit Cale Mfg.: Sonotech Reflector Amplitude % Division | |||
; I SeenD. .3 i.Of Sound Path Type: RG - 174 l Se Axiad Exa Batch 11225 UneaityRqport No.: 195 Length: Ir No. Conn.: | |||
- Type: ULTRAGEL A Caswbran Block camCoverage Mfg.: sonotech Cad..BlockNo. PO1 Uputream Q3 Da*e:tm a --- CS- Reference Block ReferenceISimulator Block Thickcness .37V5 -1.25 Die.: Flat CW6 CCW0 4an dl: 26.4 rial No., C4.3S Gain | |||
,191 Leff.0.Sound Path CaL Bik.Temp. 74 Temp.-Tool: MCNDE40129 Examn Surface: 0.D. Twvn: ROMPAS 41.. I I p. | |||
.* .. -Comp Temp. 71 :Temp. Tool: MCNDE40129 Surfa Condili:. As Ground I - I Rcordable I"dileto**)c. | |||
Resubt Acceptj Yea 0 Re~ects No 5a (IfYes. Ref. Afached Ubwonicc Indication Reoi.) | |||
InIo C LH~ | |||
Percet Of Coege Obtaned o 0%: o,N wou Data: No MAE 7YOF 94 | |||
; :'a. UT Calibratlo~ aminai Outage No.: | |||
Procedure. PDI.T4T-0"9.11.0129 Proedure Rev.: Report No.: UT-12461 Wo.iscope. SIs Wok Order No- 019582 Page: 2 of 7 Code:. 1S9S9OOoA CadLmtem: B-J 189.11 Location: | |||
Orawnig No.: 30P4I Descdpdotn Pips to Valv 3CF-44 Component ID: 3*-F4 2 .. SbW.nt: WA Thtckanes .meter. s3311250114.0 UmL i"atin: Yea.3 atUached sheet Start Time: 1145 Fnish Time:. 1200 | |||
":o ... " " .~.. eaa...--- * . *.s-- * | |||
* sm. 0uun!9Iung mualull umui Cal. Thus Datw Axial OdntAWd Search Unit Serial No.: 023DPI Seri No.: 03-M82 Checki _ | |||
Calibetln SIgnal Sweep Sm s GU Manufacturer, RT i . 1 093 Reflector Amp&udo % ODalon Modek USN so0BI Site: 2( a Shape: Re Inter. Ca 4 O 1.25 Notch so 4.7 2AW De.ay "*72 Rang: w.. F-..r. .OMHZ stye: TRL2 lnter. CaL 114 21N | |||
-Mi Cavvil: .264 Puian N3UM Exam Angle 60 #of aemennte Dua OaM.Inpng Auchg 8 Fm; Ra.ced 2Mo 0% Mode: Lon0. | |||
FnlCl13218 162 Rep.Ra,,:. APPut,,.-,,e,, M, Measured Ange: so Fi,,a,, ed Mod: Dual. Wedge StyW Interal Cal. Batch: 11225 C111umfnrentldW Orbtd Search Unit | |||
. o.ge:V " . 480 Othoer Pulwave Type: ULTRAMELI Reflt*etr Ampllhde % Sio Path Ax. GWal (0) .19".3 Cre. Gain (ft) WA Search Unit Cable Mfg.: Sonots.h | |||
_Sr.n.A S . Path .174 Type:. R MIA | |||
*i:*j:::,i: | |||
* | |||
* on~=,::,,. *ds ummL. No. Conn- Exam Batch 1122 U:"ad-.,Report No-, " '2.o, Length: v Ccn Type: ULTMA*,, U Caibratloun Ceekverage' Mg- sonte | |||
__ __1___-__km__N__'_Tr-2 __O Upstream 0 Dom am 10 Scan dB: 64.3 Reference SBak RefornceISimutator Ilkck Thic.: ess .37V-10.2r | |||
* Oie: Flat CWQ CCWQ SmcdB: WA Sedal No.: 0473 ea'n AmIus SI ISogund d8 -IReflector I~oltd Se "m | |||
0Otwilon P" Ptath | |||
,..Cal.1iTemp. 74: 'Temp. Too . MCNe400129 Exam Surface: O0.. | |||
71 romp. Too: MC,4PEA4012 surfba ConIoc . Ground As I~ | |||
-:-" -"Cmp.!Temp. | |||
Recordable .IndctG8on(s): Yea El NOl1 (IfKYe, Rof. Attached U*ltascInllmon Repeat.) | |||
Re.. | |||
:A"e:Ita. 0 eject, 0 Cnfo Pu Wkdh: 22"na P.ercentOf Coverae ObtaOed i. 90*6 No NRevtwed Pretu$a Dat, No Ia Seton Xl e ATTACHMENT ef PA6E "OF ? & | |||
I UT Calibratio.amination a 3 Procedure: NDE-40O Outage No.: 03-26 Summary No.: 03.B9.11.0129 Procedure Rev., Report No.: UT-12-461 Wofia o o. Wok Order No.: Page: 3 of 7 199812000A CaLittem: B-J 159.11 Locstlon: | |||
Drawing No.: .3CF-120 0es30p0n: Pipe to Valve 3CF-14 System ID: 53A Componen* .. t-, 3C.264 SlzaLenqth: NIA ThkiknegaDismeter. SS 11.250114.0 Lkmftations:: :None SMt Time: 1105 Finish Time: 1200 Search Unit | |||
.:SelNo.: .023DPl Serial No 57463-1706 GE Mariufac hawr. KBA Mods*el: USN so0 SW t 3.5xl~mmn Shape: Round D.lay 8.18o Range: 2.V Freq.: 4.0 MHz SbI: MSE ' | |||
-M'U CalIer: .2252 Pulser Sut Exam A Via: 0 #of Elements: Dual Dam:.ng: .ej..t 500 0% Mode: Long. | |||
Rep.Rate: | |||
Rw Authigh Freq.: 4MHX Measumr dAngle: 0 Couptant | |||
. Plte. Pl-.ed Mode: Dual Wedge IStyle: ~Intg raI Cal. Batch: 11225 Circumferentil Orlintatad Search Unit Voltage:, 460 Other. Fuilwave Type: ULTRAGEL II Calibration Signal Sweep Sound Path Ax Gb ~ 30.1 | |||
-:); Quoc. Gain (dB): NIA Search Unit Cawl Mfv Sonotaoh Refetor Amplitude % Division N/A I $ear:, I. Kn:of SoundPath Type: RG -174 Exam Batch 11225 Un"a"ity Report N''o.: " L.. Length: 6 No. Conn.: 0 Type: ULTRAGJ II nock Scan Coverage. Mfg.: Sontach Cal. Blocl.No. Component Upstream [] Downstreasml ScandB: 42.7 Relmme S RrentsSce/Simulator Block T.h;+ | |||
ic::,imess 1125, Oin.: 14r CW- CCW [] Scan dB: NIA Serial No.: 044735 I | |||
* m , = __p__ GdaBI Roftector lAmcf'lntudeI1skp Sound Path | |||
--. | |||
* r I - i UflhIWA~ f....~ I .... I IIII I II | |||
* IIIII-- | |||
-Cmp.Te 7 Temp. Tool: MCN.E..2- Surface C*ondro,* As Grourd i II - i. | |||
Recodabe Idicaions): Yes Q No (If Yes. Ref. Attached Ultrasonic indication Report.) | |||
ReIUlts: Accpt | |||
" - Reject[ C In"to Comnmensts: Inith l Section XI Exam Pe . .rcent Cov,.. | |||
. e. Oted " 90 : Yaw Rav.owed*..evi.us Date: No AITACKNE11 A' PABE 7( IF 14 | |||
A. a DUKE POWER COMPANY ISI LIMITATION REPORT ComponentlWeld ID: 3CF-126-4 Item No: 03.9.11.0129 remarks: | |||
0 NO SCAN SURFACE BEAM DIRECTION Scan limtation due to DLIMITEDSCAN (01 02 01 2 S cw 0 ccw castvalve. | |||
FROM L. N/A to L N/A INCHES FROM WO CL to Beyond ANGLE: 00 0 45 0@ 60 other 60RL FROM 0 DEGto 360 DEG | |||
' NO SCAN SURFACE BEAM DIRECTION QLIMITEDSCANC I 0 2 0 1 [ 2 C cw 0 ccw FROM L | |||
* _to L INCHES FROM WO to ... | |||
ANGLE: 00 045 060 other FROM _ DEG to - DEG 13 NO SCAN SURFACE BEAM DIRECTION UMITED I SCAN 0 :102 ( 1 [1 2 Cw [cw FROM L to L INCHES FROM WO to ANGLE: 0.00 45 0o60 other FROM DEG to DEG | |||
__ ________________________ I ___ | |||
j NO SCAN SURFACE BEAM DIRECTION 0 LIMITED SCAN 010 2 [ 1 El 2 Cw Ccew UT-1 2-981 FROM L to L INCHES FROM WO to Sketch(s) attached 4 | |||
ANGE:00 50 pn o~er - FROM DEG to DG Z yes [ No Prepaed BY. David j | |||
ATTACHNENT I4 PABE'?? 804G' | |||
Supplelm Report Report No.: t I61 Page: S of 7 Summary No.: .3.89m.0129 Exminr: GWeOW. David M. 'Leveloys: 1141 Reviewer: Date:K7. | |||
Examner. Halglr T Level:U. Site Review: | |||
Othe" l LA r "Level: NWA ANDi Review: Date: | |||
: .Comments:" | |||
P/P16- Vol-vle Skeich or Photo: | |||
-S2-ATTACHNENI -1 PAIE ~D? | |||
Supple m Report Report No.: | |||
Page: 6 of 7 Summary Noi: 03.89.11.012 Examlner GrIebel. Davt A Level: i-N Revewea, AJ~ c4in~e,#~~ Date: | |||
f Level: f1-N Site Review: Date: | |||
Examiner Hagleir, Tarry, Othet WiA Level: NIA ANII Review. | |||
l C~ommenfts Thicknes &Profile | |||
-VWY25 Sketch or Photo: | |||
~ - | |||
= * | |||
. -- T NZ~ t~ | |||
ATTACUHEE!I i | |||
rIE??F9 ME* | |||
o | |||
Determination of Percent Cove rage for UT Examinations - Pipt Site/Unit Oconee I 3 Procedure: PDI-UT-2 Outage No.: | |||
Summary No.: 03.139.11.0129 Procedure Rev.: Ef Report No.: UT-12401 Worksoope: IsI Work Order No.: 0195838: Page: 7 of 7 45dea Scan I 100.000 %Length X 0.000 %volume of length II O= 0.000 % total forscan I Scan 2 100.000 % Length X 50.000 " volume of length /I DO 50.000 % total for Scan 2 Scan 3 100.000 % Length X 50.000 % volume of length 1I )O= 50.000 % total for Scan 3 Scan 4 100.000 % LengthX 50.000 %volume of length/ I DOa 50.000 % total for Scan 4 Add totals and divide by 0 scans 37.500 % total for4S deg Other deo - (to be used for supplemental scans) | |||
The data to be listed below Is for coverage that was not obtained with the 45 dog s Scan 1 " Length X_ %volume of length I 100 M %total for Scan I Scan 2 " Length X % volume of length I iO0 - %total forScan 2 Scan 3 %Length X % vokume oflengt i 100= _% total for Scan3 Scan 4 % Length X % volume of length I 100.ox% total for Scan 4 Percent cornigeto covemsa Add totals for each scan required and divide by # of scans to determine; 37.500 %Total for complete exam SIte Field Supetvlsor. ~i2 ,i11. - Dat r 4 a . ! * .. . | |||
I. | |||
UT Calibratio I na sAllount Ocoeeg I.. . 3 *NDI-610 Outao No- '_ -_ | |||
Sumnmary No.: 03M.C13002 Procedure Rev.: Report No-- UT-1.246 is' Work Order No.: Po*o: I of Code: 1....ooA ComJim: CA IC.3 'Lo _ | |||
ang No.: .... o~o-201.8-00.1 oesctonc Tubeah, t to SheU System 0D: 03 Cop qet;D 3,SGA.WU 6welliellgh: MIA Thaanesi~smeter. C31I29M2INA fvata lonh Yes -Se attached sheOt tot Tmo; 11O Finsh Time: 1410 Ins.iva.." Seotin ." Seao, unut l ., "D3 ia OUnied Search Unk S a! o.: .- .. OOW HDIC Seril No.: F2.8M. Checks -. | |||
XRAUTXRAMER Collu,,kxn Swnh SweeCp Sound Patn | |||
_____________ Ko - Relect. Amp*Itwde % Dedan Model USH4, Sime: 0.75 Shape S.,,d "lr11in so 1.0 1.07 Dda~. | |||
1.26 igo 1.0 Fmq.:. 2.25 M~z Sw~e: Ganuna .!! 2565 2A4 2A3 A",,! C4~ 9311 .. P"*.er k h E=m Ang*e: 0 Sao Et , ",, ,1,v.Cl. 1 318 35 36S 3A. | |||
ReJo 0% s - -K Lo. Final Cal 1 530 WI I Rep. Rate: A,1Kohgh feq.: 2R5 MHZ* Moesured Angle: 0 CLuplmut o:lt,: | |||
. . Fied Fxed Otow,. __t___ | |||
U...Pwaw Interal call Type: | |||
121w ULTRAG*RI. II Clr-urnfen"l | |||
=on SW" OrientatedS""Search Unit V | |||
A.Gain (do- :36A Cite. Gain (S)X WA search Unit Ci"o Mfg.: SONOTgeC Refleclor Aptds % oMalon - | |||
I Screen Div. 11.0 In.of Sound Path Type: RO . 174 Exam Batch 12125 NA unety ReWP ..: ... Lft w W.Cann-* o Type: ULTRAG. .-.- | |||
C m: ~Scan Coverage Mfg.: SONOTECH '_ _ | |||
-Ca. Blackb T.",lc"kn | |||
,"",m,,5.0:O | |||
.... 01"44o | |||
:':aIS.: ... _______ _ | |||
Upaliii 6a Downstream OWN ] . (COW - | |||
Scan dB: 434 Soan dB: NIA *Gata Peencei*Io~i O.: J ReIuitlek Sco17 Pu0 | |||
::Cal.SIlk TeMp. .-73 Temp. Took: MCD--131 x.am Surface: O.9. Sei p45°n | |||
:.. Temp. .74: Temp. Took MCNDM401. Swim.Conotdon: As.rd T -ne , P .:,0 Recordable Indlcation(s):* Yee No (if Yes. Ref. Afttahed Ultrasonic Indkcaton Report) ___ | |||
.Reoulta. Accept.r . Reject lwJe 0*Q*Cr-t BacIeln lost at 2. fro* weld tooedue to tubedot. | |||
iPecen Of CPeameOtie 0: N Reviewed Prev~ous Data: yes WA Ransom. reg .. | |||
Examiner:,-.. e IA.: Sonature Dole SU Di | |||
*' .. C,--. | |||
....... :/2 Other Leve U" WA natureDo atrDb ATTACIKNENI 4. | |||
II FABE'~( OF%~ | |||
UT CaIlbratIo Iriation Coon.. 1 Outage No. & M_ | |||
Summaay No.. oa~cis&om NeowdM Rov. * .7 Repet No.: UT-41417 Wadcaoope: lit Work Oero No.: Pass: 1 K. | |||
CaL~em: .A ,ct.so .1oallon Daciltn Tubestet to Shel System ID: o3 Component !D: 34, .W ,, iselfeangth: MIA Thloluesa~lemeter. iSI &12rI NIA lbiim. ions: Yes - Seeaattached sheets StanyTme: 1150 M~rall ie 1410 | |||
___________ I -. | |||
instrume.nt Sett.ngs Search Unit Cal. TIi. . Date Axh' Ortenteted Search Unit Seral o.:23P0 Sedla No.: 1.2910 Checks I . Calbaution Sgns.- SWOOP ISound Pamh Manybutstsre GE Manufacturer. KBA Inia cOl l.OM' 7M1201 Reflector Amplhide 7* DMIviio Mod " USH. so w Sim: X.01.0 Shape: Ra," 1 nter. C aL ___ 0_ | |||
_ M1 so 1.1 1.3.. | |||
. .737. | |||
La. Range: 1,-s Freq.: 2.25 MHz Style: C, Ma I nter..Cal. 1 *I I _________ 2.6 1.1W M^ CaWel: .1270 Pulser. Square Exam Angle: 35 8 it B Smento aY50 &9 C wIFe.Ce tl._ ,n_+, | |||
DamplW 5004 Reject 0% Moea: | |||
to Notch 100* U. L6.25 Rep. Rate: Auolg Freq.: 2.25 MHz Meassursd AngWe: 3? *514T 4., 6.4 7.60". | |||
Flfter Fixed Mode:"' P Wedge awtye: SW . Cal Sauch: .121"U SIlrcumfrentlal Orintatd Search UnIt Volt*a.: .450 Other. Fu.wave, Type: ULTRA2ELn'f Cuilbrmllon Signal.- Sweep Ax Ganin* do 30.0 CIMo Gain (45:o 30.0 Search Unit Cable Mfig. GONOT9CH: Reflecor Ampilbde Divison SudPath S ari - 1.2 in.of Sound Path Type: RG -174 WA Exm Batch 12CIS IhisWiy Report No.: 1.12-10 Lwnufw v... ft. Cams.: 0 Type: . ULTRA*tL I Sean Coverage . MUg.: SO-bTiE. | |||
C4 SlOck No. 2oT.240 Up*eam Downstrvewa ScaB:.44.0 Re,*erncelm mulator lock Thlkns . ~ . 'a CWG5 CCWfi Scan dB: 44.0 Sr o: 041 GaidiR lnra-iector l,.% .+SWOOI Sound Path | |||
.. Cal. BTemp. 73 Temp. Tool: MCNDE40131 EtmnSl O.u.e . Type: RQMIAS As Ground ,. . 19.6]r RadlueL 50 IA LOD, Comp. Temp. 74 Temp. Tool* MCNDE4OlI3 Surkae Conditlon: | |||
*: eco.dablelR IdicatIon(s). Yes Q No (If Yes. Ref. Attached Ultrasonic Indhcatn Report) | |||
Result:* Accept Q Reject | |||
* Info 0 Comments: Cafbratlon raefectors Virtifid uing dynamic scan. 3.. | |||
so.o Percent ..Of Covge lObtained 00%: No Rehlqed Prvous 0te . Yes Examiner Lewe /gn0Oae 04i Reviewe sw.ab" Dat Oats Level NA DIm flat NIA Ele~vew / * ~ J *~IO nAh 4 -- | |||
NIeA Leve wA ww-W Dale ~pCow Dals | |||
. e, .0. #./- | |||
HIA -d~ | |||
I | |||
.t~7 ~ -~ .. ., - .P.k~ | |||
~- | |||
AT TACOHEN TA-0 II 'PAIE 0 4 | |||
UT .Calibratloe mnt q SamýiyN. | |||
Oco '1.. .I | |||
* ND420 Outage N" OLCI.30.0002 PWrcekOr Rer-. 7 Report No. W21 | |||
'Work Ordeir No.:. | |||
liS *~3648 Pagp: __ofM__C11 11991120HA Ca.*lhm: C-A CI.25 domUos II 0M401.S-0001 m n , ktp c Tubahhet to Shill System. 10: 03 Component 0*: S.SG-W69 NIA t~~mltat 76.76 YsSeal sheets SWtTirs: 1153 Finlsah Time: 1410 | |||
* luabumen~ft Settngs Search Unitkl Axia Orientateol Search Unit Seial N.: No.. Serial Not: C | |||
..U:arufteboec 1CZJTKCAjER. Mauacue KRA Initial Cal 0931; 5171=20 CaI b n Signal Sweep Pat Reflector Amplitude % Divulop ud a Moc UNOStv. 1*1 Shape: 'Round inter. CaL__ I15 70 T 1.2 18.4" De: fer. 1..'w Ra ge:; | |||
e Sane Gamm Inter. CaL 1113 ; r 25oe9 2A 3.75 Md C.nVe: 1274 PUlsa. Hig05 Ao,- Inte - | |||
. ampng. .. 1K Reject 0%. Mode: shear. .n Cal 1542 Wr712 ID -oc lp 10in 4.8 7.45 Rtep. Rate: Antohgh Fr...: 2.25 Ha Meaud Ane 47 couple fit .aon 40 Uo LW Flitec wie Mode: P Wedge SWye *. owi Cal. uatdr, .1212 Clrcumferenftas Orientated Search Unit Votg: fied Other Pullmav Type: ULTRGE'LD Ax. Ga:in(dD) 44.2 Ckc. Gain (d.) 44.2 Search unit Cabl" Mfg. SONbiEC. | |||
I reasowY*3 1.5 in of Sound Patlh Tpe RG - 174 mfati 125 efctr AmplitDeI % Division SoundPat S :n..L.... y Report No.:; L-l Lg, VLo NO. CoWL 0 Type: ULTRAGME U Signal Sweep, Block 0.lbato soen coverage Mfg-. SONTUiR Ca.BokNo. .20T.2A0 Upstreami Dowvsneeamfo ScandB: SU Thilckness ..$A Diaz. Fla CW0 cow0 SqefldB. -u 6617- | |||
!ellN. Gain Signal &APSw S Path ElamO SS" .D. Tpe : :j!L RialMNo dB Reflector Ampltd %1 Divelet Cal. 9IL Tem p.: emp.. To k. | |||
T .73 NDE40131 | |||
.*...C r fItediusI so 0 IA I 2.gr | |||
.C"mp.Tep". 74 Te"p. Toolk MCHE.i'.:' Surface C*d.il. As Ground Recorda"bIueldlo*aion(s): Yes | |||
* No ' (ifYes, R*f. Attached Ultrasonicla lnloIM Report.) | |||
Re.: t::.. Accept : Reject Ea Info I Comments: CaWlbraton refneto Verified v u*ng dynamic san. | |||
Percent Of | |||
.Coverage Obtaine *,. 90%: | |||
No: Reviwed Previous Data: ..Yes | |||
:-i., , Revee ale | |||
_ .- Lev | |||
*i:i!i?:i Halger~ ony 575212 Examinrbr Level WZA d Sie'a other. Leel A SDgnbuaw Date Date NIA v | |||
* i-.iU ATTACUKEUT 19 MAE 9-3 Ff /, | |||
UTCalibrtionI~rinaflon U::. | |||
-... UDEm Outage No. - $ | |||
Suminay No.: _ _ 03.& ~1iOM02Procedure Rev-* 7 RepmtNo.. UT4248S? | |||
leiWodcOrder No-: oigmt Pap: 3 0, | |||
-od.c~ 190810M Cat.uim: CA 161.3011 Orwing No., 0I.21.-0001 | |||
== Description:== | |||
tubiaee to SheD System ID:. 03 pntID: 3.rA.WO r .. .I Skefu " WA Thicineagl* ama I.N"A. | |||
*,--n: Yes See, Wad - ,-'f .SW Tk,. 1155 Fish Time 1410 Insirnient Settings Search1 Unit ~ | |||
Serial No.: TJXT SOW No.; OLL CheckT* | |||
Mah~bwwf.ue K0UTCRAMER manufacimin: iCBA milal cal 0ae.517U1212 Rfeo Smpigna e Swee" U | |||
* Model:.. USNI | |||
________________SIM:_____ 1.0 -h. -on . we__ . | |||
so____ 1.3 -. | |||
2.8? | |||
:i:sy: s 17.=420 Range: " .0 FrTq.: 2.24MHz Style: Gonua Inter. Cal.5 2 so - - | |||
_V___eN.: | |||
A26-l- .... ExmAngl: so#Ofl .3 -w. 6Z.. . -a. a m*n S m 0 4. | |||
W 7O SWPAMh Sound | |||
_______ Rata_____ .5Mz Wu~lFe-Age Maued le: IWS Cal. I 20j. 41A____ WoL | |||
: 11. Scareen Di.12-067 f Pula.tih Son TypAnge: | |||
__O___ | |||
SO -of1lma4 a - | |||
Type:' asw 358 See___ _____ | |||
R.1ep.Repert No.:: -2.250 MHZ of V No | |||
________ a. CUpLmaant _______ | |||
DaExnm*aK .e-. 1, | |||
..... Scam Coverage MW. S0NbYrlCH | |||
. .. ;:Cll.. R.. tNo:L120 a.licuMock:. Iigli NO.0' 1.' .tpeU T .E.. ,,II. I *. | |||
Votage.: | |||
.e.: | |||
BlockNo. . | |||
_________ d e Flat 2_T___Upstream______ 1. S .d.B Typ: ULAU_dB._US I C1aiian S Ognal SWeepd Unck ras..Gain B 48.6 C Gain d 4w8,.5..g..~.. al M.. . d.B R lec Apiid,, % Division SCreL kTemp.n 7 Temp.0To MCIrI 0Son ExatSh Type ,O , UTyp, 1, S Aod"- | |||
A.., | |||
L | |||
.. s1.. Tap 73*m.To CU4OS mSrae Type: ROW.AS 42.0 r Radius so 1.0 &W c*mp. Trep. 74 Temp. Toot MCNOE4O13, Sure Condition: As Ground Re'ordable Indication(s)= Yes Q-' No*1 (IfYea. Ret. Aflached Ultrasoidc lndi*al.n Rape.*) | |||
Resuft AccW C] Reject [Z InIoQ Cotmnits: Callbrallon nefloctora verkied "sin dynamic seam. | |||
.Pertcent Of Coverage Obtained >80%: No Reviewed Previous Data: Yes Exeulrther Level. jie-PAN/r intueDt Day. oh... . 5*7.1202 | |||
[Examiner Lve WA SignatuviewDae IWA NSA',: | |||
,ter v WA Signature Data I CEI 1-,49 PA 0 | |||
UT Calibrati . Ilation ocanes I NbSd2 0gepmw 03I.0..0002 Procedure Rev.: I is' Work OrderNo.: 01956846 Page: 4 of- -4,(15 catftamn: C-A C1.30 La~Uoe: | |||
1.201.8-4001 Dascrlptlo ubeaheto Shell System :ID: 03 | |||
: ompon-nt 10: +-- GA-W ShtasA~noh- WA ThllheasD~mesn 0 125*1WAIN Li o: -"Se attached Staanybme:. 1315 Fbsh Time: .1410 | |||
- ________ U ~-. | |||
Search Unit. - I III II I I I CaL I Time Daft AxkW Odkaktotd Searc Unit Scula No.: 00TJixT Seal No-, 07M1L, check -.- Calibrallon signa Sweew Mmufacue,-~ KRAUTKRAMER Mantugwollge KSA kn"a Cod, 085W=712 OU Relotor Ampid % DImon aime 1.0 show. Rouand Itr a AO t__-_lo 1.8 .80 - | |||
Fmq.: L25 M-- Sl"'lemun.. | |||
ItrCa.13154 V=702 I * '__o-c:Ll _In. | |||
56 4.2 P2.Ir* | |||
I K".CaI~et .12167 Pwsew Wgi Exam Anqle s ot00flernmnt: Singl ! _______ 40 6GA 3.14* | |||
Dampln 1K Reieol 0% Mode: mew I 1555 iro¶20121 I-tail, 114?rSON 48 5.1 2A8r Rep. Rata Autohh -Preq. 2.25 MliX measured Agte 6 | |||
* Cupism | |||
- . Y. | |||
... Filtr Aixed MMe: Circumfuowl" Orienltatd Search Unit F Wedge Stli SINS COL Safti IM25 V~lae -Fixed Other. Fullmeee Caibraflon ftrud &we"P onPa Ax. Gain (dII): 4U. Cia Galn(,)c 46.0 Seach Unit Cal" Mfg...: SON Re1e,.,r AMplit % | |||
i ,,, ,Ison. . | |||
I Sren~v~ ':J~o Soflnd Pat Type: RG - 174. Exrn . 12, Linealy Rqport No.w:20 L .f.. Nv fotCo,.: 0 Type: UL1O.*L U Scan Coverage , mwg,: SONo'mc Ca~bratf on Block Of Soc*t No.1. 2OT.40. Ups&*a=n Downem O , Z Scan d: 620 S -ree ,Refegece/Skoulatr | |||
. I uI 81ocA o' | |||
Reference Bback 50 | |||
&hcnes DID.: Flat OW COW Sam do. 62. GaI I Sig- | |||
:Ca. 8kem p. +, 73 Tem Tool CD4O3 | |||
, .Ewen Swk,,, | |||
s ,,o.D.. - reulal No.: .08.1451 dB Reffectior Arple%I DMIel '" SoI | |||
___.s_Pam ryPe . , | |||
....T Cp.Temfp. 74 Temp Tool MCDdIA ¶ :.Srae odo: sGon Recf .l. Ac Ye Ref. aca IRdiajeotRepInt.) | |||
Reut: .Rjc | |||
:if Acp Comments: Cealtion efectoes Vrelied using dynaic s=am. 14T. | |||
SOD to OAX. 44.o dI. | |||
ParcantOf Coverm~ Obtained ; 0%: No . . ewe Previou Data: Yes C.AD~Jon Nao reiu & | |||
!nuAe Oeaes SORvewMop NIAA | |||
'D~e as1 | |||
:e oftbU NIA I&Z ATTACHNENT 4 PAGE gOF '?* | |||
DUKE POWER COMPANY ISl LIMITATION REPORT Component/Weld ID: 3-SGA-W69 Item No: 03.C1.30.0002 remarks: | |||
0 NO SCAN SURFACE BEAM DIRECTION Lateral Restraint #1 E- LIMITED SCAN [ 1 0 2 0@ 1: 0 . 2 cw C3 cow FROM L 2-12.5" to L 2+12.5" INCHES FROM WO, CL+3.0".. to Beybnd ANGLE: 000. 45 . 60 other 6ONS FROM N/A DEG to N/A, DEG 0 NO SCAN SURFACE BEAM DIRECTION Lateral RestraInt #1 | |||
:E LIMITED SCAN ED 1 0 2 [1 1. 0- 2..K cw 0 *ccw FROM L 2-12.5" to L 2+12.5" INCHES FROM WO. CL+2.0" to CL-2.O" ANGLE: 00@ 45 0 60 other 6ONS FROM" N/A DEGdto N/A DEG 0 NO SCAN SURFACE BEAM DIRECTION -Lateral Restraint #2 E- LIMITED SCAN 0 1 02 09 1.' 'S 2 .l cw 0 ccw FROM L 9-12.5" to L 9+12.5" INCHES FROM WO CL+3.0" to Beyond | |||
.ANGLE: 0 00 45 0 60 other 6ONS FROM. N/A DEG to N/A DEG 1Z. NO SCAN SURFACE BEAM DIRECTION Lateral Restraint #2 F1 LIMITED SCAN ED 1 02 01-'[l 2 Cw0ccw | |||
:.FROM. L 9-12.5" to L 9+12.5" INCHES FROM WO "%+2.00 to CL-2.0" *Sketch(s) attached ANGLE: '000 45080 othe " 60NS FROM- N/A DEG to N/LA,_ DEG I yes E' No Sheet 5 of 1i. | |||
. 7- OWt ATIACPHMENT 6ý-. | |||
0 0 MAE Y0f | |||
Oe B 1~ | |||
DUKE POWER COMANY ISI LIMITATION REPORT omtonentfWeldID: 3--SGAW69 Item No: O3.e1.30.0002 remarks: | |||
s NO SCAN SURFACE '.BEAM DIRECTION Lateal Res"taint #3; LIMITED SCAN I0 ( 2 Z- 2 cw@3cw cw __ | |||
FROM. L16-12.5' toL 16+12.5- INCHES FROM WO CL+3.0_ to BCynd.. | |||
ANGLE: 000 45 060 other 6ONS FROM N/A DEG to N/A DEG | |||
: 0. NO SCAN SURFACE BEAM DIRECTION Lateral Restralit #3 | |||
[] LIMITED SCAN 0 1 0. 2 3 t 0* 2 j@ cw 0 ccww FROM 16 4-12.5" toL 16+12.5' INCHES FROM WC: CL+2.0" to CL-2.0" ANGLE: 00 I045 .060 other 6ONS FROM N/A DEG to N/A DEG 0 NO SCAN SURFACE BEAM DIRECTION Lateral Restraint #4: | |||
[]LIMITED SCAN ;1 02 [Z I. ED 2 0 aw 3 ccw FROM L 24-12.5" to L 24+12.5" INCHES FROM WO: CL+3.0" to Bey0ad ANGLE: 00 | |||
ý130 45 060 other 60NS FROM., WA DEGto N/A DEG . | |||
*:1 NO SCAN SURFACE BEAM DIRECTION Laterai Restraint #4: - | |||
I::E]LIMITED.SCAN 1 I Z] 2 El ! F.[3 2.0 aw 0WI. =cw FROML' .24-12.5" to L 24+12.5" INCHES FROM WO _CL+2.0"' to CL-2.0" .Sketch(s)attached | |||
:ANLE*I :.!'0.0.0 45 [] 60 other 60NS FRO.M:-. N/A DEG to NIA'. DEG 0* yes " -13 No | |||
:Prepared: Gregory Ra!!som *al: '" Date. 05/07112 Sheet. 6 of 15 "dam Re.iewed .Authoiec B:A | |||
.. z Date: /,;_***' | |||
64,;7L."* :* | |||
spect6r: -. Date: el* Z' ATTAUNHENT~ | |||
DUKE POWER COMPANY ISI LIMITATION REPORT Component/Weld ID: 3-SGA-W69 Item No: 03.CI.30.0002 remarks: | |||
0NO SCAN SURFACE BEAM4 DIRECTION Latera Restrint #5 I LIMITED SCAN 0,1 02 10 .2 [1cw[ ccw FROM L 31-12.5m to L 31+12.5" INCHES FROM WO. CL+3.0". to .Bend ANGLE: 00.0 45 060 other 6ONS FROM N/A DEGto N/A DEG 0 NO SCAN SURFACE BEAM DIRECTION Lateral Restraint #5 | |||
.E] LIMITED SCAN 0,1 02 - 10 2 Scw*0 CCW FROM L 31-12.5" toL 31+12.5" INCHES FROMWO" -L+2.0 to CL-2.0" ANGLE: 000 45 10 60 other 60NS FROM N/A DEG to N/A DEG 0 NO SCAN SURFACE BEAM DIRECTION Lifting trunnion QLIMITED SCAN "I1 02 01 EJ20cw lccW FROM L 1-9" to L 1+9" INCHES FROM WO" CL+7.0 Jto Beyond _ | |||
ANGLE: 0 00 45 060 other N/A FROM N/A DEGto N/A DEG 0 NO SCAN SURFACE BEAM DIRECT.ON Lifting trunnion l LIMITED SCAN 0I-1 0 2 0 1.. E]"-"2 El cw I:.ccw .. | |||
FROM L 12-9" to L 12+9" INCHES FROM WO' CL+7.0" to Beyond Sketch(s) attached ANGLE: [J0Q 45 0 60 other N/A FROM N/A DEGto N/A. DEG 10 yes ' No Prepaed B. Gregory Ransom , ,V4 .v.I. .Date: 05/07/12 Sheet 7 of 15 | |||
°.. | |||
Reviewed By. Date, Authorized Inspectdr~ | |||
, _ 00t.: | |||
-: | |||
* I-N OZ. Z | |||
* -ATTACHNMENTI | |||
.PA6Ef'f.F' 4 . | |||
*1:. | |||
As 0, | |||
DUKE POWER C6W~ANY ISI LIMITATION REPORT ComponentWeld ID: 3-SGA-W69. Item No: :03.C130.0002 remarks: | |||
*0NO.SCAN SURFACE @EAM DIRECTION. Marway ILIMITEDSCAN 0i 2 Z- 1. [3 2 3 cw E .ccw SF'ROMlL7-10" .to L 7+10" INCHES FROM WD CL"7"" to Beyond ANGE: *0*45 *060 other FROM NIA DEG to N/A DEG ElNO SCAN SURFACE BEAM DIRECTION 0 .LIMITIED SCAN .IIE 02 | |||
] 51[JEl2[0Jcw Elccw ._ _ _ _ _ | |||
FROM L to L INCHES FROM WO "_ ._ to " '_ __.,. | |||
.ANGLE: .[10 045 0-60 other FROM. DEGto DEG El: NO SCAN SURFACE BiEAM DIRECTION 0 LIMITEDSCAN E01 [ 2 EI" t. 0 2 0c .. w __ __ __ | |||
FROM. L toL INCHES FROM WO to ANGLE: 0 0 0-45 0 ,60 other FROM. DEG to "___DEG i0E NO SCAN SURFACE 6EAM DIRECTION | |||
. LIMITED SCAN El [1r2 [" 2[1l cw C ccw FROM L to L INCHES FROM W0 to - Sketch(s) attached 4 | |||
ANGLE.: -0 5:D 060 other: FROM, DEG to. DEG 0 yes " No eeae..Ge"oryRansomn 0507/12 Sheet. 8 of 15 | |||
:::~le ... )7r=*:* .1/1 ZA,& Z .'-n:I Authorized ez*, InspecftcV.. .I re | |||
.Date: =- | |||
Reviewed, By ae: | |||
ATTACHNENT1 4 PAM[O OFft-0 | |||
Steam.. Generator Upu* besee Sel This scan limitation exist for 125" of weld lewth Weld No. ; 3-SGA-W69 Total Scan Coveage fOr 00 CW & (CCW Iten No. :.03.C1.30.0002" Scale 1"=2" e t OOdW&CoM I | |||
I... | |||
I. | |||
Base MdI ýe .34 sq. in. | |||
S Weld Mea A .ea=636 sq. in. | |||
Total | |||
,Are-=15.7sq. in. | |||
Stwa 1-. .besheet Surfce 2 - Shell | |||
: 00. C.W& CCW Coveiage - .- Y 1.7.sq..... x 12S"-19625 sq. in. 'I 15..7 sq..... | |||
* 465.. 73005..sq.uL a. | |||
1962.5 sq.in.- 7300.5 sq, in..= 5338 sq.in. | |||
(53 38 sq ini -7300.5 sq~In.)100=73.% of Weld e94:e Page-I-Of- ATTACOHEII.W 0 pA6 Eb F Pd | |||
Steam Generator Um&-rubeshet o Shell 4p This scan limitation exists for 125" -ofweld 1IM Weld No..: 3.SGA-W69 Total Scan Covdagp for Near Surface ItemNo. : 03.C1.30.0002. | |||
Scale I" = 21 | |||
[at=]a Riswin T 60P Surfce I - Tubesheet Surfam 2- Sll | |||
".!"a S:3.71 ;sq. | |||
in.mtotal Near surface volume 311* s. in. x465"= 1725.15 sq. in. | |||
3071 sq.in. x 125"= 463.75 sq. in. | |||
463 W...75,sq. ýin- 1725.15 sq. in--1261.4 sq. in. | |||
1261.4/1725.15 x: 100= 73.1 % | |||
Itspector//Date: | |||
M fF | |||
.Steam Generator Uppdrubesheet to Shell Ibis scan limitation exists fbr 125" of weld lenge.. Weld No. :3-SGA-W69 Total Scan Coverage for Weld Metal Item No.: 03.C030.0002 Scale I"= 2" LateralRe | |||
. . i. ii | |||
.:..Base Area 7T84 sq. in WeldMetal Area 4.17 sq. in. | |||
Total Exam Area 12.01 sq. in. | |||
Surface 1- Tubesheet Surface 2 - Shell 5 . | |||
*0 ..... | |||
* VM d Metal Covemge Wed..Metal Total Area..4.17 sq. i x 465".1939.05 sq. i*. | |||
S* Metal Total Area Not Sca*med=3.48 sq in. x 12 I.. | |||
,435 sq.dvi - 1939.05s.n.x154. | |||
T sq. i. -q9.05 (1::i0504.05 sq.inJl939.05 sq.m.)100 77.6%of W#ve hispector/Date: | |||
Page I Of IACNHEM I A' | |||
* , .V MAE & OF4~ | |||
0 :Steam Generator.ppi re..... .... o Shell .p This scan limitation exists. for 125" of weld length Weld No.: 3-SGA-W69 Total Scan Coverage f6r Weld Metal with 600 Item No." 03.CI.30.0002 2" " | |||
Scale 1 Lateral ResOW Base NMkal Area = 7.84 sq. in. | |||
:Weldl* .Area-=4.17sq. in. | |||
Total ExamArea= 12.01 sq. in 4-Surface 1- Tue Surface 2- Shell V.i 1d:Mta Coverage w/600 4..*,17 sq.. x 465"= 1939.05 sq.i 1..65 sq. in.weld metal not scanned x 125"=- 206.25 sq. iL 206.25,sq.in. -1939.05.sq.in.= 1732.8 sq.insobtained I.. | |||
I73-28 sq.inJ 1939.05:sq.in.)100- 89.4 %of vWd eli In'spector IDate: 2 PA e- | |||
/t ofjý AITACH NE NT t9 | |||
]~ PA6EY3' OFY6. | |||
0; .Steam Generator Upp~rubesheet ito Shell Tiis scan limitation exists for 125" of weld lenmgh Wed No.: 3-SGQ-W69' Total Scan Coverage for Base Metal Item No.: 03.C1.30.0002 Scale 1" = 2" | |||
* LateralResU~nt | |||
-. p | |||
.. ~ 4 f..a . .. **.. .;~*..*- | |||
Base Metal Are -7.84 sq. i. | |||
Weld MNetalArea =4.17 sq. in. | |||
Total ExaArea= 12.01 sq. in Surface 1 - Tubesheet Surface 2- Shell Base Mel CDvU-a 7..4 sq.irn x 465=-3645.6 sq.in. | |||
.5.18 sq. ih bsemetal not scaied x 2**= 647.5 sq. in. | |||
647.5 sq.in. 3645.6 sq.in.= 2998.1 sq.in*obaned | |||
.(2998.11 sq.inl 3645.6 sq.in.)10( 8.2 %of BM I. | |||
Vr~ector/Date t3 e~jofjýATTACHNENT A S. PA6Ey'OFf6; | |||
; | |||
- | |||
== | Steam Generator UArýueseto Shell a,' | ||
This scan limitation exits for 125"of weld leieh WeldNo.:: 3-SGA-W69 Total Scan Coverag. fOr Base.Metal with 600 Item No. : 03.C0.30.0002' Scale P = 2" La1er4R~strunt~ | |||
p BaseMea lArea*=784 sq. in. | |||
We-d Metal Area 4.17 sq. in. | |||
Totai l E ii4o ea.= 12.01 s% in Suri I1-Tubesheet Surface 2- Shell BaeM etal Coympa w/60P 7.4 sq.i. | |||
" k..4".3645.6 s.in. | |||
1.81sq"... oscanned x 125"= 226.25 sq. in. r I. | |||
226.25 sq~n 3645.6 sq An.= 3419.35 sq in~obitained (3.419.3.5 s7.inl 3645.6 s*n-i)1-393.8 % ofiBM lbspector /Date: | |||
Pgg'r f 4ýA 7A ER E'T | |||
0 Steam Generator Shell to Tubesheet Umitations Item No. 03.C1.30.0002 / Weld No. 3-SGA-W69 | |||
-~LU Total 00 Scan eraSe 73.1% . | |||
Near Surface Coveraep Scan Angles % Coverage Obtained S1 600 73.1 S2 60 73.1 C-W 60' ... 73.1" CWW 60W 73.1 Total Near Surface Aggregate Coverage = 292.4/4 73.1% | |||
Weld Coverage Scan Angles % Coverage Obtained 51 45, 6Q' . ".73.1. | |||
S2 450, 60 (77.6 +894)2=83.5 CW 350, 45*,* 60* 73.1" 0'' ."" Cww -450, .6 73.1 Total Weld Aggregate Coverage = 302.8/4 = 75.7% | |||
Base Metal coverage Scan Angles % Coverage Obtained S & S2 350, 450, 600 73.1 CW & CCW 450, 60° (82.2 + 93.8)/2 = 88.0 Total Base Metal Aggregate Coverage = 161.1/2 = 80.6 % | |||
Total Aogremate Coveraae= 73.1% + 73.1% =75.7% + 80.6 a 302.5/4 = 7:.% | |||
Inspector/ Date . S/" -7 / V- Paso-L-4zoff . | |||
PaeA}} | |||
/ Weld No. 3-SGA-W69 Total 00 Scan | |||
Date |
Latest revision as of 19:29, 25 February 2020
ML13273A037 | |
Person / Time | |
---|---|
Site: | Oconee ![]() |
Issue date: | 09/26/2013 |
From: | Batson S Duke Energy Carolinas |
To: | Document Control Desk, Office of Nuclear Reactor Regulation |
References | |
13-ON-001 | |
Download: ML13273A037 (122) | |
Text
DUKE Scott L. Batson Vice President LI4LIR Ie Oconee NuclearStation Duke Energy ONO1VP I 7800 RochesterHwy Seneca, SC 29672 September 26, 2013 o:f 864.873.
864.873.3274 4208 Scott.Batson@duke-energy.com ATTN: Document Control Desk U. S. Nuclear Regulatory Commission 11555 Rockville Pike Rockville, Maryland 20852-2746
Subject:
Duke Energy Carolinas, LLC Oconee Nuclear Station Unit 3 Docket No. 50-287 Fourth Ten-Year Inservice Inspection Plan Request for Relief No. 13-ON-001 Pursuant to 10 CFR 50.55a(g)(5)(iii), attached is a Request for Relief from the requirement to examine 100% of the volume specified by the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME Code), Section Xl, Rules for Inservice Inspection of Nuclear Power Plant Components, 1998 Edition with 2000 Addenda (as modified by Code Case N-460).
The attached Request for Relief 13-ON-001 is to allow Duke Energy to take credit for the enclosed Table 1 list of limited ultrasonic examinations performed on welds associated with various systems and components during Unit 3 EOC26 refueling outage. The ultrasonic examination coverage of the subject Unit 3 welds did not meet the examination coverage requirements of Code Case N-460. The coverage examination obtained for each weld is provided in Attachment A of the relief request.
Achievement of greater examination coverage for these welds is impractical due to piping/valve geometry and interferences. Therefore, Duke Energy requests that the NRC grant relief as authorized under 10 CFR 50.55(g)(6)(i).
This submittal document contains no regulatory commitments.
Ifthere are any questions or further information is needed you may contact Corey Gray at (864)-873-6325.
Sincerely, Scott L. Batson, Site Vice President Oconee Nuclear Station Attachment A www.duke-energy.com
U. S. Nuclear Regulatory Commission September 26, 2013 Page 2 Xc w/att: Mr. Victor Mcree Region IIAdministrator U. S. Nuclear Regulatory Commission Marquis One Tower 245 Peachtree Center Ave., NE, Suite 1200 Atlanta, GA 30303-1257 Mr. Richard Guzman Project Manager (by electronic mail only)
US Nuclear Regulatory Commission One White Flint North, Mail Stop O-8C2 11555 Rockville Pike Rockville MD 20852-2738 Xc w/o attachment Mr. Eddy Crowe NRC Senior Resident Inspector Oconee Nuclear Station Ms. Susan Jenkins Section Manager Division of Waste Management Bureau of Land and Waste Management SC Dept. of Health & Environment Control 2600 Bull St.
Columbia, SC 29201
Oconee Unit 3 Relief Request 13-ON-001 3EOC-26 Limited Exam Coverage
Oconee Relief Request 13-ON-001 1.0 Scope of Relief Request Relief is requested pursuant to 10 CFR 50.55a(g)(5)(iii) for welds listed in Table 1.
These welds were required to be examined in accordance with Inservice Inspection Plans for the following Units.
Oconee Nuclear Station - Unit 3 Fourth 10-Year Inservice Inspection Interval Interval Start Date: January 2, 2005 Table 1 Relief con Examination Weld ID Item/Summary Examination Reques; nit Performed Numbe Number Data Section umber (Refuelina Number Outaae) 2.0 3 3EOC26 3-PZR-WP26-1 03.1B3.110.0009 See Attachment A Pages 1-20 3.0 3 3EOC26 3-PZR-WP26-2 03.B3.110.0010 See Attachment A Pages 21-40 4.0 3 3EOC26 3-PZR-WP26-3 03.B3.110.0011 See Attachment A Pages 41-53 5.0 3 3EOC26 3-PZR-WP26-7 03.B3.110.0012 See Attachment A Pages 54-66 6.0 3 3EOC26 3-53A-15-26 03.1B9.11.0106 See Attachment A Pages 67-73 7.0 3 3EOC26 3CF-126-4 03.B9.11.0129 See Attachment A Pages 74-80 8.0 3 3EOC26 3-SGA-W69 03.C1.30.0002 See Attachment A Pages 81-96 Notes:
- 1. Duke Energy procedures require ASME Code,Section XI examinations that do not meet the requirements of Code Case N-460 to be marked "reject" for tracking purposes, regardless of whether indications were noted. Therefore, the limited exams in 13-ON-001 without indications were marked "reject" on data sheets.
- 2. Duke Energy has invoked Code Case N-663 which allows elimination of Code required surface exams for welds listed in Sections 6.0 and 7.0 of this Relief Request.
Page I of 22
Oconee Relief Request 13-ON-001 2.0 Weld # 3-PZR-WP26-1 2.1. ASME Code Component(s) Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-1, Summary Number 03.B3.110.0009, and ASME Code Class 1.
2.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code,Section XI, 1998 Edition through the 2000 Addenda.
2.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-l.
2.4. Impracticality of Compliance Component configuration
" Surface 1: Shell - Carbon steel
- Surface 2: Sampling Nozzle - Carbon steel
- Diameter: NIA
- Thickness: 6.188 in.
This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a),
T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following:
Weld coverage using 45°, 60° & 700 shear waves for axial scans (SI, S2),
and 450 & 60° shear waves for circ. scans (CW, CCW) obtained 12.3%
coverage.
Base material coverage using 45°, 60° & 70° shear wave for axial scans (SI) and 450 & 600 shear waves for circ, scans (CW, CCW) obtained 49.3% coverage.
- 00 scan coverage obtained 29.1% coverage.
- The aggregate coverage was calculated to be (12.3% + 49.3% + 29.1%)/3 = 30.2%
The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is Impractical.
Page 2 of 22
Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case.
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied.
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only.
2.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. Radiography (RT) is not a desired option because RT Is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would incur the same physical scanning limitations.
2.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.
2.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0009 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity.
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions.
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.
Page 3 of 22 7.
Oconee Relief Request 13-ON-001 2.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006.
Page 4 of 22
Oconee Relief Request 13-ON-001 3.0 Weld # 3-PZR-WP26-2 3.1. ASME Code Component(s) Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-2, Summary Number 03.B3.110.0010, and ASME Code Class 1.
3.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code,Section XI, 1998 Edition through the 2000 Addenda.
3.3. Applicable Code Requirement
/WB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-I.
3.4. Impracticality of Compliance Component configuration
" Surface 1: Shell - Carbon steel
" Surface 2: Sampling Nozzle - Carbon steel
- Diameter: N/A
" Thickness: 6.188 in.
This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following:
Weld coverage using 450, 600 & 700 shear waves for axial scans (S1, S2),
and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 12.3%
coverage.
Base material coverage using 45*, 60° & 700 shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 49.3% coverage.
- 00 scan coverage obtained 29.1% coverage.
- The aggregate coverage was calculated to be (12.3% + 49.3% + 29.1%)/3 = 30.2%
The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is impractical.
Page 5 of 22
Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case.
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied.
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only.
3.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would incur the same physical scanning limitations.
3.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.
3.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0010 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity.
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions.
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.
Page 6 of 22
Oconee Relief Request 13-ON-001 3.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006.
Page 7 of 22
Oconee Relief Request 13-ON-001 4.0 Weld # 3-PZR-WP26-3 4.1. ASME Code Component(s) Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-3, Summary Number 03. B3. 110.0011, and ASME Code Class 1.
4.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code,Section XI, 1998 Edition through the 2000 Addenda.
4.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-l.
4.4. Impracticality of Compliance Component configuration
- Surface 1: Shell - Carbon steel
" Surface 2: Sampling Nozzle - Carbon steel
- Diameter. NIA
" Thickness: 6.188 in.
This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following:
- Weld coverage using 450 & 600 shear waves for axial scans (SI, S2),
and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 15.4%
coverage.
0 Base material coverage using 45° & 600 shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 54.8%
coverage.
- 0° scan coverage obtained 33.8% coverage.
- The aggregate coverage was calculated to be (15.4% + 54.8% + 33.8%)/3 = 34.7%
The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to sampling nozzle weld would have to be redesigned and replaced, which is impractical.
Page 8 of 22
Oconee Relief Request 13-ON-001 The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case.
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied.
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only.
4.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. Radiography (RT) is not a desired option because RT is limited In the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would Incur the same physical scanning limitations.
4.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.
4.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.63.110.0011 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity.
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions.
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.
Page 9 of 22
Oconee Relief Request 13-ON-001 4.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006.
Page 10 of 22
Oconee Relief Request 13-ON-001 5.0 Weld # 3-PZR-WP26-7 5.1. ASME Code Component(s) Affected Unit 3 Pressurizer Sampling Nozzle to Heater Belt Shell, Reactor Coolant System, Weld # 3-PZR-WP26-7, Summary Number 03.B3.110.0012, and ASME Code Class 1.
5.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code, Section Xl, 1998 Edition through the 2000 Addenda.
5.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-D, Item Number B3.1 10 Fig. IWB-2500-7 (a), 100% Volume Coverage of Examination Volume A-B-C-D-E-F-G-H-I.
5.4. Impracticality of Compliance Component configuration
- Surface 1: Shell - Carbon steel
- Surface 2: Sampling Nozzle - Carbon steel
" Diameter: N/A
- Thickness: 6.188 in.
This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a), T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following:
Weld coverage using 450 & 600 shear waves for axial scans (S1, S2),
and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 15.4%
coverage.
Base material coverage using 450 & 600 shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 54.8%
coverage.
- 00 scan coverage obtained 33.8% coverage.
- The aggregate coverage was calculated to be (15.4% + 54.8% + 33.8%)/3 = 34.7%
The impracticality was caused by the weld taper configuration of the sampling nozzle to the shell that does not allow meaningful interrogation from the Surface 2 nozzle side. In order to scan all of the required volume for this weld, the shell to Page I! of 22
Oconee Relief Request 13-ON-001 sampling nozzle weld would have to be redesigned and replaced, which is impractical.
The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case.
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied.
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only.
5.5. Proposed Alternative and Basis for Use No substitution alternative for this weld is available which would provide better coverage. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would incur the same physical scanning limitations.
5.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.
5.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B3.110.0012 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section Xl, 1998 Edition with the 2000 Addenda.
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity.
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump and Reactor Building area radiation monitoring contribute to ensuring pressure boundary integrity by providing means to detect reactor coolant leakage and take prompt corrective actions.
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.
Page 12 of 22
Oconee Relief Request 13-ON-001 5.8. References Duke Energy Relief Request 05-ON-001 was approved by the NRC during the last inspection interval. The previous approved SE is documented in Accession Number ML060830291, No.TAC No.MC7308 dated April 17, 2006.
Page 13 of 22
Oconee Relief Request 13-ON-001 6.0 Weld # 3-53A-1 5-26 6.1. ASME Code Component(s) Affected Unit 3 Piping Weld, Low Pressure Injection System, Pipe to Valve (3CF-11),
Weld # 3-53A-15-26, Summary Number 03.B9.11.0106, and ASME Code Class 1.
6.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code,Section XI, 1998 Edition through the 2000 Addenda.
6.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-J, Item Number B9.11 Figure IWB-2500-8 (c), 100% Volume Coverage of Examination Volume C-D-E-F.
6.4, Impracticality of Compliance Component configuration:
" Surface 1: Forged Stainless Steel Pipe
" Surface 2: Cast Stainless Steel Valve
- Diameter: 14.0 in.
- Thickness: 1.250 in.
This component was scanned manually with conventional methods. Scanning requirements are described in 10CFR.50.55a (b)(2)(xv)(A)(1). These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following:
- 458 shear waves obtained 47.2% coverage in one axial direction
($1 - pipe)
- 450 shear waves obtained 0% coverage in one axial direction (S2 - valve)
- 450 shear waves obtained 50% coverage in one circ. direction (CW).
- 45° shear waves obtained 50% coverage in one circ. direction (CCW).
- The aggregate coverage was calculated to be (47.2% + 0% + 50% + 50%)14 = 36.8%
- Best effort supplemental scanning was also performed using 600 refracted longitudinal waves for interrogation of the inner 1/3 of the wall thickness on the valve side, but is not qualified to be calculated into the above claimed coverage. The supplemental refracted longitudinal waves were only used for interrogation in the axial direction per procedural direction. Supplemental scanning is not performed in the circumferential direction.
Page 14 of 22
Oconee Relief Request 13-ON-001 The impracticality was caused by the taper configuration and cast stainless material of the valve which cannot be effectively interrogated by ultrasound.
There are currently no examination techniques that have been qualified through Appendix VIII for examining cast stainless steel. Therefore no coverage could be obtained by scanning from the valve side. There was also a branch connection limiting the axial scan from the pipe side. In order to scan all of the volume for this weld, the valve and branch connection would have to be redesigned and replaced, which is impractical.
The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. Therefore, the available coverage will not meet the acceptance criteria of this Code Case.
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied.
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only.
6.5. Proposed Alternative and Basis for Use This weld was examined using procedures, equipment and personnel qualified in accordance with ASME Section XI, Appendix VIII. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws, and has not been qualified through performance demonstration. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the cast stainless material. The use of any other UT technique available would incur the same physical scanning limitations.
6.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.
6.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B9.11.0106 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity.
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump monitoring ensure pressure boundary integrity by providing means to detect leakage and take prompt corrective actions.
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable Page 15 of 22
Oconee Relief Request 13-ON-001 results for the coverage completed by the volumetric examination, the pressure testing (V'-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.
6.8 References None Page 16 of 22
Oconee Relief Request 13-ON-001 7.0 Weld # 3CF-1 26-4 7.1. ASME Code Component(s) Affected Unit 3 Piping Weld, Low Pressure Injection System, Pipe to Valve 3CF-14, Weld
7.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code,Section XI, 1998 Edition through the 2000 Addenda.
7.3. Applicable Code Requirement IWB-2500, Table IWB-2500-1, Examination Category B-J, Item Number B9.11, Figure IWB-2500-8 (c), 100% Volume Coverage of Examination Volume C-D-E-F.
7.4. Impracticality of Compliance Component configuration:
- Surface 1: Cast Stainless Steel Valve
- Surface 2: Forged Stainless Steel Pipe
- Diameter: 14.0 in.
- Thickness: 1.250 in.
This component was scanned manually with conventional methods. Scanning requirements are described in 10CFR.50.55a (b)(2)(xv)(A)(1). These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following:
- 45* shear waves obtained 0% coverage in one axial direction (S1 - valve) 450 shear waves obtained 50% coverage in one axial direction (S2 - pipe)
- 450 shear waves obtained 50% coverage in one circ. direction (CW).
- 450 shear waves obtained 50% coverage in one circ. direction (CCW).
- The aggregate coverage was calculated to be (0% + 50% + 50% + 50%)/4 = 37.5%
- Best effort supplemental scanning was also performed using 600 refracted longitudinal waves for interrogation of the inner 1/3 of the wall thickness on the valve side, but is not qualified to be calculated into the above claimed coverage. The supplemental refracted longitudinal waves were only used for interrogation in the axial direction per procedural direction. Supplemental scanning is not performed in the circumferential direction.
Page 17 of 22
.... . . .... .. . .............. . . . . . . .. -- . . ... .. .. ... .. . ... . . ... . . . .. . .. ...-. . . . . . I
Oconee Relief Request 13-ON-001 The impracticality was caused by the taper configuration and cast stainless material of the valve which cannot be effectively interrogated by ultrasound.
There are currently no examination techniques that have been qualified through Appendix VIII for examining cast stainless steel. Therefore no coverage could be obtained by scanning from the valve side. In order to scan all of the volume for this weld, the valve would have to be redesigned and replaced, which is impractical.
The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. Therefore, the available coverage will not meet the acceptance criteria of this Code Case.
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied.
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only.
7.5. Proposed Alternative and Basis for Use This weld was examined using procedures, equipment and personnel qualified in accordance with ASME Section XI, Appendix VIII. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws, and has not been qualified through performance demonstration. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the cast stainless material. The use of any other UT technique available would incur the same physical scanning limitations.
7.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.
7.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.B9.11.0129 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.
The system leakage test performed each refueling outage in accordance with Table IWB-2500-1, Examination Category B-P requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity.
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump monitoring ensure pressure boundary integrity by providing means to detect leakage and take prompt corrective actions.
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable Page 18 of 22
Oconee Relief Request 13-ON-001 results for the coverage completed by the volumetric examination, the pressure testing (V'-2) examinations required by Section XI, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.
7.8 References None Page 19 of 22
........................................................ 71
Oconee Relief Request 13-ON-001 8.0 Weld # 3-SGA-W69 8.1. ASME Code Component(s) Affected Unit 3 Steam Generator A, Feedwater System, Tubesheet to Shell Weld
- 3-SGA-W69 Summary Number 03.C1 .30.0002, and ASME Code Class 2.
8.2. Applicable Code Edition and Addenda ASME Boiler and Pressure Vessel Code,Section XI, 1998 Edition through the 2000 Addenda.
8.3. Applicable Code Requirement IWC-2500, Table IWC-2500-1, Examination Category C-A, Item Number C1.30, Fig. IWC-2500-2, 100% Volume Coverage of Examination Volume E-F-G-H 8.4. Impracticality of Compliance Component configuration:
- Surface 1: Shell - Carbon steel
- Surface 2: Tubesheet - Carbon steel
- Diameter: 148 in.
- Thickness: 5.125 in.
This component was scanned manually with conventional methods. Scanning requirements are described in ASME Section V, Article 4, T-441.1.2(a),
T-441.1.3, T-441.1.4, T-441.1.5, and T-441.1.6. These requirements describe and are specific to scanning components in two axial and two circumferential directions. This component was scanned to the extent possible to meet these requirements. The aggregate coverage that was obtained is described and calculated from the following:
" Near Surface coverage using 600 shear waves for axial scans (S1, S2),
and 600 shear waves for circ. scans (CW, CCW) obtained 73.1%
coverage
" Weld coverage using 35c, 450 & 600 shear waves for axial scans (S1, $2),
and 45' & 600 shear waves for circ. scans (CW, CCW) obtained 75.7%
coverage.
- Base material coverage using 35°, 45°& 60° shear wave for axial scans (SI) and 450 & 600 shear waves for circ. scans (CW, CCW) obtained 80.6% coverage.
- 00 scan coverage obtained 73.1% coverage.
" The aggregate coverage was calculated to be (73.1% + 75.7% + 80.6%+ 73.1)/4 = 75.6%.
The impracticality was caused by four lateral restraints that did not allow scanning from the Surface 1, CW and CCW direction, and allowed only partial scanning from the Surface 2 direction. In order to scan all of the required volume Page 20 of 22
Oconee Relief Request 13-ON-001 for this weld, the lateral supports would have to be redesigned and replaced, which is impractical.
The Oconee Inservice Inspection Plan allows the use of Code Case N-460, which requires greater than 90% volumetric coverage. The achieved coverage did not meet the acceptance criteria of this Code Case.
This relief request is specific to examination volume coverage limitations only. All other Code requirements were satisfied.
No indications were recorded during this examination. The reject box is marked for internal tracking purposes of the coverage limitation only.
8.5. Proposed Alternative and Basis for Use This weld was examined using procedures, equipment and personnel qualified in accordance with ASME Section XI, Appendix VIII. Radiography (RT) is not a desired option because RT is limited in the ability to detect service induced flaws, and has not been qualified through performance demonstration. Use of other manual or automated UT techniques, whether conventional or phased array, were considered, but would not increase coverage due to the limitation created by the component configuration. The use of any other UT technique available would incur the same physical scanning limitations.
8.6. Duration of Proposed Alternative This request is for the duration of the fourth inservice inspection interval, currently scheduled to end on July 15, 2014.
8.7. Justification for Granting Relief Ultrasonic examination of the weld for the item number 03.C1.30.0002 was conducted using personnel, equipment, and procedures qualified in accordance with ASME Section XI, 1998 Edition with the 2000 Addenda.
The system leakage test performed each period in accordance with Table IWC-2500-1, Examination Category C-H requires a VT-2 visual examination to detect evidence of leakage. This test and VT-2 examination provides additional assurance of pressure boundary integrity.
In addition to the above Code required examinations (volumetric and pressure test), Reactor Building Normal Sump monitoring ensure pressure boundary integrity by providing means to detect leakage and take prompt corrective actions.
Duke Energy has examined the weld to the maximum extent possible utilizing approved examination techniques and equipment. Based on the acceptable results for the coverage completed by the volumetric examination, the pressure testing (VT-2) examinations required by Section Xl, and the leakage monitoring, it is Duke's position that the combination of these examinations provides a reasonable assurance of the continued structural integrity of these welds.
Page 21 of 22
Oconee Relief Request 13-ON-001 8.8. References None.
Page 22 of 22
Attachment A to Relief Request 13-ON-001 UT Detail Data sheets from 3EOC-26 Limited Exam Coverage
UT Calibratioamination 3 d.. _. NDE-540 Omge No.: 03-26 SMwnay "o:w0.3. tJDE.640 110m" .Pmm~dg Rev-: RqIt No.: UT42441
ýzc.. Wm110p131I 5 SI Wodo.NowsuOrer Coda,19W00 Cetttm . 13.t Liaion:
Ormawhg NO,: SION.0 oipo:Nileto he Syale ID:o Ul801 SamU No.: OOJISeim No.; A152W I.. Dl Ia. AxIslOdenteledg-al Us*
_________________ Mestcal lis" 0 Ca~aden S"pe o
$WS e mwPa Reflactor Ampfbido S I Ohdon IIssD wS 1.50 lie1
- F kW oaL~ 1210 4l2012 W1sSOI 70 3.3 3W RaA.
Ras f Riq.: 2.25_M2z Anle:
Nfata WanCoplno 313 8D 6i5 m
- M
- ~~ ~ ~
P
~ ~5): ~Aiq ~NGa0~
it.Gi ideI1 Itga IU CaLBah wberod: 112
-SO" I
05 4 -~- IA I-I -
Ea ei fiCaiui
- o)2. t _________
CbWjmbrenW Oibnbftd $Gwch th*
Ch'eumfuu'enthl OulenWed Simh Unit U-I. -
b 2 Us hiooWAg . C WA. anwm&l
- Coamal.. signa PEhrgo Wede Catege Mi.
Cal. Sntee Rabaler AmpSlide % - a-WA __I I
.3Lokie 7 O l: P1m C O Con SearcCoA 55:
- T-s
- I -
- -- tmpComp U T mp.oot SmcNmg~
Pawic Cmye RG Go1n4 bhmm3glgw Weak am ,. --
Dateach 112 Nj(7f.W Tow waes Ripen~ UT40.47 for appileid Ihltwlom ATTACINEIT A pAi I air q*,
- !:iO DUKE POWER COMPANY 11S LIMITATION REPORT omipen.MWeld ID: 3-p.ZR-WP26-1 ItRm No: 03.3.110.0009 rmarks:
- NO SCAN SURFACE BEAM DIRECTION uto nozae coaguratln O LIMITEDSCAN 1D 02 [ 1 0 2 0 Cw ED ccw FROM* L"NA toL NIA INCHES FROM WO Toe to ,Beyond ANGLE: 0003 45 060 other FROM 0 DEGto 360 DEG 0 NO SCAN SURFACE BEAM DIRECTION E' UMITED.SCAN 0I1 0E2 0 1 2 ED cwEl __w FROM L to L INCHES FROM WO ,_ to ANGLE: 00 045 060 other - FROM DEG to DEG 0: NO SCAN SURFACE BEAM DIRECTION 0 uMITED SCAN 0I 10 2 0102 Ecw 0 ccw FROM L ____toL INCHES FROM WO .... t0
- .FROM .OEG,,to, DEG
" 7." " "'l
ýANGLE: _00045 060 othe g S .. . I
- NO SCAN SURFACE BEAM DIRECTION 0 LIMITED SCAN 0 10 2 01 [ic2 0 cw l-caw UT-12-941 FROM L. to L INCHES FRO? AWO to .Sketch(s) attached 4 -' No 00 ANGLE:..E 60 other__ FROM - DEG to DEG 0 yes
- . m -- +
a, u 1111. a I /
MAE '2.OF q 0
UT Calbratiosamination Oconee I 3 Proedum: Outrge No.: 03-20 Summazy No.: :OB3.11 IIEIi:*!::
- i, : i Wod oo .: o.009 ""Procedure Rev.: .7 *Repet No- UT.12-4?
. 92-
..
- Work Order No.: r...5 *4 IS OIMRAn
---. a -- --
i*~4 IIa.. .
Dra g :N6.
IS.,C DOWOpiln* Mazdae to Shell Systm ID :o : ,w0 CompoetI:3PRW2 UWWLOlg NIA ThkdmeaI0IAm~t- CS 16.188 1NA 618I1s6rament Settings. su I.la -ix'.
121 :
T~imeh 1312 Srial:No.: 1searesh Unit OOTJXTSeulal N0.: ,H2 ,7, 4 Ca Time Date Axial Odentated Search Unk
- MacujX" IRUKAER menua huer: KBA Cho
- ike Inital Cal 1049 4==0121 SCalibraatlon ReMeto Signl Amplikade %
wp Dvision Sound Path Moe:USN-40 Size: Inter. Cal.
.sxI.0 Shape: *et. li s0 Do l:ea
- 11.31 "R9zge: 15.0o Freq.: 1A 2.25-2.253 MHz Slyl: Inter. CaL 1233 412M201
- ]: .12" 8. Pwu.. . :
Gamma 35 3.0 4.70" igh E m.. ngle: Inter.
45 Oaf Elementr: Single 308 20 4.8 Dapkng 0%
.KRja 7.00" Mods: : Shear Cal 114131 4r20203_
PAP. RAWe Autohlgh FM.. Notch 1 11.6 6.80" 2.2*3 MHz IdAngle: 4. FaneB Ceuplodt 615 16 1 A0 12.20"
- xed ..
1:1:ii od&.. :PE Wedge Styl: aws Col. I ClrcuN~fereatlil Orientatedi Search Unit
.: . Ax athn (dB) :: Type: ULTRAGEL U Calibration Sigal Sweep
_463' Ci. Gain.(dS)f ...4.3 Search Unit Cable.. Aft.: Sonotw,. Reflector Ampdltude % DOvision Souhd Path
___ cee' Di 1.5 in;of Sound Path Type: RG - 174 WA "'
Exam Batch 11225 Uneasiy* Ret No.:
- _
- L1.42.=.2 6 No. onA 0 Type: ULTRAGEL II Sc8an Coverame " Muw:
- Cah!itlui-on Blo*k Sean Cowase sonoteci.
Cal.:. BlckNo. 40338 UpSRIn QDownstream , . Scan do: 6.3 Thilckniisa Reference Bloek Referenceimulmlator Block
...--... . Temp.:7.Tm. Ca Flat CW 0 CCW 0 scen do: 52.
P.7;: .MCiDE4012S- -n 0.
cwSurface:
. -: No.: 6-4M mp.Temp. do RfetrAptd Divoision 0emp.Took MCNDEO"* I2 SufAIc CondIsdlo.. A-Gound
- Recordable Indicts: Veag 0 No 0 (f Yes. ReL Attached Ultraonlc Indication Rtepeal).
Reut: Accept Reject0 Ino3 Commeft: NW tA OfC.o e e : No Rev.e..d Preom " :
fl.Nigntur E~Datee Reevewe Staufer Loafer, 6. 1201201Daf DO A412=012 .DaVd.
NIA Dt v
FA 6E '3 of J(
UT CaIlbrattbrQ~amrniation Ocorie :1 .3 IProcldure: *NDE.828 Outa No.: 0o-.6 Suimmary No-: .03.83.110.0=0 pmW6*nuo Rey.: Report No.: uT.1r24'
" 01858430 Pago: 2 of 10
.Cod:. -Y1920CA CatAtem: " ih 13In110 Locaton:
DmvAwng.No. I"l-CN3402 Description Nozzle to Shall SytmID: 5 Comiponnt 10: 3PZR-.WP2s-1 . Size/Lngth: 'WA ThIcklimssilameter. CS16.1881NA SUmitiolns: Yes .*Soattached sheet
'...___.______.... .. .__"__*_"____r____r __._-____,.__Tlmo. 1218 Finish TIme. , 1312 __
- .m_* ..... * *1.,,Jl,*l Search Unit Axial Oriested Search Unit Cal. Time . Dot Sorlal:
- No.:I : OT..T S.esia OIRSN " ChecksJ Calibration sogna Sweep Sound Path
- :Manulachir. KRAUTKRAMER . Manufac trer KBA 7nli;uICa 10531 412010112 Reflector Ampliud % DMivson Modal: " USN4O SI'ce: .Sn'.O Shape: R*e.t .5 80 2.0 1,_X" elay:. 14.07..- Range: Wo" Fr-mq Inter. C*l. 1.0 704.0 2.25 MHz Stye: Gamma.
... caweo r ug so _ 3e:Eleme Inter. Cal.
.1269 Putter Mighh ' E Am n.. 1.5 55 0.0 Sb" Final Cal 1415 4M20121
-Ompwng: . K Roject: 0% ... Mode: Shoea .2. a 8.
Rep. Ra.e: Autohigh Frq.: 2. Z NM* Measur : Couplet 114 5 7.0 3.42-Filter Fixed Mode: P.t Wedge Angle:- ,'~swoI SS CaL Batch: 11M22 Ckcumurentlal Ore "tas- Search Unk Voltgep: Fied: Other Ful.w.ve Type. ULTR.AGEL U 3oun path A. Gaifn (cB) 0.5 Clr. Gain (dBft Tn6. Search Unit Cable M onotech Sg Redactor TA4m Oika Divso 9 , -,,= .9 n.
RG - 174 See, PjAl Scren Div. A. of In. Sound Path Type: Exam Batch 11225 i' No. Conn-- ,v_0
.W l Report Ho: " 14 )No, 0 Length: Type: ULTWAGLNI Soon C movrage. Mfg.: Senotech Caltiratlon Block~
Cal. Black Mo. 40338 Upastral 0, Downstram a Sean A: 7. Referee,,,Simulator Block Si80na III cnes al 81kTen
.. 7
_p..-70 ,,w.-TO 01...
Fist EI -
CW EZ
.-E..msusm. fo,........0.0.
CCW 0 SWa dB:. 70.
Sedel No.: .9&W=52 I4 I.1 dBReflector jAmoWli*twd ivaown 39A r2 Radius, 1
'e
, ,' Pa
-04 2.00 4- C". .p;.Temp. 80 Temp. Tool: MCNDEOI402 Suiface Condition: At Grcund Recordable Ind~cation(s): Yea [3 No Ea (if Yes. ROEfAttached Ultravorde Inication. Report Results: Accept 0 Reject 0 into [Q *Commants: wxA S-,. .,. M~E £(OF f ý
W: eInt Ocoese 11 3 UT Callblatt-amInation Procedue: HOMO62 Outw No.:
Di 034.
03.33 o.1100,
- Summ ay No,- Procedure Rev.: ReplM No.: UT.12414T
.. . :....: " " .~ l " 019554M0 Workscope: Work Order No.: Page: 3 @1 16 1998=200A CmAtJem: S.D 163.110 Location:
Drawing No.: DescrIP11n.' Nozzle to Shell Component ID:.3PRW2. S/ALength: NIA ThiclmsuIblmeten. CS I6.161NA Um"italonsi Yea. S attached she StartTime: 1218 Finish Time: 1312 I I . - II In:sabomen Seanr ,ch Unit CaIL Tme. cots Axi Orrentated Serch Unit SerialoI : '.OOTJXT Se"al No.: OIR93N" Checks Calibration Signa Sweep SudPt
. n:- a:ur, . RAUTKPAMER Manufacturer KA "Refector Ampibde % )islo% _
... ... . 0Simz: .5X11.0 Shape: Reot. Inter. Cal.
DebT.* > 14.9? . Range:
- ': *::i:i;*~
.I* m'.*: *;:. .2.0" m.* , :*Fmq.m 3.25 2,211 MHzs Sy:
Smo. ,
..Gap. :mma Inter. Cal. 1255: 41201201 2M__ 30 2.6 SW MtCAW~t~2S Ple Wgh Exam Anigie: 60 Vof 116eqviea: Single - Cal. I -I
.Daiping': . K. '2" Rej: IFinal Cal 1 ¶4q*412001 Notch 60 5.0 12.10" Mods: Showr Re:. Rat*: Autoh" h Freq.: 2 heasured Aer e:60 . - Coup lant S16 7.0 Filter Fixed Modw. PE WedgeStyle. , w Cal. 5.ft . 11225 Cinumbnntereal Orientate search Unit Volage.Fie .Other: P..ulflavs TYPe: UILIRAGEL HI Caibraom SOWna Stwep Sound Path AyL.QGain (doft::54 " Oe Gain ("YS). .5 Search Unit Cable Wa: Senotech Reflector IArnyp~a % DiWhao
- ":"""...: ..::.-: Scr*a~v"::i2 .:"I.0 * ;..Soun~dPlll." .Type-W-.J I ~ u .5 jp f Bon ~h Tp:RG .174 NI-A Exam Batch .. 11225
-n..... Report No.: ....LI 2-200.L.ng.h.-r.N-...on.. 0 Type: U0.11AGEL If Rol _____m~ Boc Ce*"ibatlo S k 6Bloc.ck,,.,e.O
.: " onatch
- Cai.** SiocNai Up*s tream0Q Doenstreem 1 Scma doB: 66.5 .
Thcies 7 Di.: .,e-ia.*pAU CWE@
. _ CCW. ..0 Siam dS3
-_ 68.5
... m No.: ""4592
- . ...C A imp..-.oc':.- T .M~ ... .Ea - _ ROMrA-Sra F I -1 dB IRerIcW flbaeftItDivsionI~
~ -
CMA-. Te.rp. se rer.P.TCo: 10 .... MCN E46_.o 28 S.bdo n: As ound...
- r
-- *IWAl 8 I J I 2.oo-RecodablIlIndWeo(a)n it Yes 0 No 0 (ifYea, Re* Attacd Ultreeonlcindlcallon Report.)
- Re.u' ts:.:...
.. . A..c.;.. .t.. .... . .. - info t ,Comments: MIA Percet Ofoveros btane +;00%: +
No Reviewied Previous bata: :you .
Exm~e Lve ~ainature Date Reviewer Signature 8 StufrLesterE.! 1021 Exmnr LvlDaeSt eiwswgatb" Date Othar..I" SDat WreeAvi 1021 ATTIIAM11iU A I'PA6E,5OF I (.o
UT Callbratir0 amination Oconse Procedmeure... NDE460 Outag N.l " 0346
$am:na:w y No.: .B3.110.0000 P rede Re" 7 Rep No.: UT"12447 owOope:c 181I :. WoikOrdor.No.:
01935420 Page; 4 Of 18 Cdm. *4 .1 - .. Cat.em: 10 Locadm N . ,,,,0,,,"0"Deal,* ,-ac.itg . .. N aS . o sholp Syst' : : ""so ComponentfID:
".. .. WPll "l Wg Thlclmew0lametern CS i.i A
!i1 "-atlons:None - . . StetTIMe: 1218 FInIsh TIme: 1312
- .. - U - I F Instriuient Setffng. Search Unit Axl Oreatead Search Unit S.ea.,No.*: , ,OOTJT Serts. No.: ___ 21,87,__ __"
CaOMMtON. SkInal S"We So0nn~ Path IntdCaLCall fI'ns 1100 M41201112Da.te Reefctwr Amplu40 , DIimeon
-Model: USN.40 S.:e: lXI Sh*pe: ARud Inter. Col. - - 114T SON W7 2.1 air Dela...y.:.....:... 19.018. Ran2.:2.2 . * -Me: MHz .smnt" MIr. CaL 1308 , 2 IlZ SOH 20 4.0 11.1v
.. "C.lVe'I .1268 P..-
e : High .. um Ang.e: 70 Sof _-S , =ne. Cal.
3Wr SOH 10160 "".A ...lai D:mpba,. ,
- 11,,ct:
- 0% . od: Shear FKS:Cid 1W2 IDmaNt 20. 76. 21".
Rep.q R~ts, DdItbgh: F"X14 2.25 lmo AngiS0 4*rON .. 10: 9O. 1. 60.'
-- Fer" : Fiox Mdo: " PE wedge Style: " Ws- Otrumfent 9Qatalad Search Unit Voltge: Fixed Othier. Fuliwa Type: ULTRA*EL In Caiatkn
- T,' -
"" Sinl
. - Swepo.- "
A- Gain (013X.nB) 661--.5 . Gai (dB "NIA Search Unit Cable : Ufg--. Sonotech Rfletor Amplitue % Divson rudPt
- .:Smn.0 2, 0 n " SII9d"P.th Type: RG-174- Exam Batch 11228 Lie AltyRepeat Noi.: Let. W No. Cwm.:.. - Typ. ULTRAGEL n
Calbaslon Blca.""j Coverage .Mfg: Son.te.. .
cal. o':" N. .'. ...." ... .pstream 0 ow In @ Si : " .5 RefrerncellMulator Block Ref*ernce Block Thi-.ci". ss " 7. W.a.: Cw"
-CaLi em--707em.*-ToeL -MCND4OI2- Flat
..- m4rbc:- .
CCW ] Scann
.. dS: WA D...o..- *'
-.. e IYPW No.:.
- - fln.
649
- iWA I
I F-I dBI Reflector IArZW9 %
r n IM~ ._
~l 49.3 ZRadWs 90 Q.T 2.W
,:,: ,,.,," Te*0,,'
mp. ,0, Temp. To : m.n., surface Co*b*t,,Ai,- . ,u -
Reor-dote Indleavon(s): Yes. [3 No. (I Yes. Ref. Attached Ultasonic Mcalcit Repmd.
Q esi. '-.. ..Ac ept E, R.-eject In.o e*rcn :*IX CovferaoObtia.ed 90%' .. No Re.iewed Previous Dat: .Y'.
AITACHNEN] A
.AME ý IF II,
F.
DUKE POWER COMPANY ISI LIMITATION 'REP Component/Weld ID: 3-PZR-WP26-1 Item No: 03.B3.110.0009 :remarks:
0NO SCAN SURFACE BEAM DIRECTION Due to nozzle configuration.
0 LIMITED SCAN ] 1 0@ 2 0 1 [] 2 0 cw 0 co FROM L N/A to L N/A .. INCHES FROM WO Toe: to Beyond _-
ANGLE: 0 0 .45. I 60 other GONS FROM 0 DEG to 360 DEG 0 NOSCAN SURFACE BEAM DIRECTION Due to nozzle configurtion.
'0-IMITED SCAN 01 .1 2 OO 2. *w ccw FROM L NIA to L N/A .INCHES FROM WO Toe to .Beyond ANGLE:. 00 0_14V 08.:60 the r 70 FROM ;0 DEG to :360 DEG
- 1 0 NO SCAN. SURFACE
- BEAMDIRECTION 0I I 0 2 0 1. 2 0 cw 0 cow
.FROM L _._*. toL. INCHES FROMWO " to CANGLE: 45 60 other FROM -
DEG to -
DEG I I NO SCAN:
...... SURFACE BEAM.DIRECTION 0iIMITED.. SCAN 01 .02 C"1.0"2`0 w 0wccw. UT-12-947
- to"L" . . INCHES FROMW WO ___. to Sketch(s) attached 000. . .4 ANGLE: 5 0 60 other FROM :DEG to __ DEG 0yes 0 Dew: 04120/12 Sheet~ 5 of 18 Au Date:
- ~~~A-**I "- I~e nsPecOA{
ATTACINENE tj.
MAE 7 OF Ij4
item No: 03.B3.11.0009 Pressurizer almno NoMe to Shell 450& 600 0 Wed No&: 3-PZR-V, 2W1:
lqlnfnacp Tliqtlqnr' eiiiewm 1 f n Nozzle Total Area Coverage Exmined with at least 2 angles from ome ection. Surface 2 A combination of 450& 600 angles were used t obtain maximmn amout of coverage.
"l ".'.." *'... *.
16.88"
.i
'12 .4t".
45 a -
- . -I Shell Surface 1 r T, T T t t %T ý , , K r, r T, K, T, , x x x x I -- - - - - - - - -
k e e 6 of Is *?ATACIElgi A
Ite No: 0i3.1O040069 Presurizer S lingNozzle to Shel HMr. Shell p
- ,::ii:*Weld No.::i 3-PR-W26-1l:. .
ScanPlan.
Acombination of 60*& 700 angles were usedto obtain a maximum amout of covrage on tae surm.fce. Nozzle Surface2
" 19.72" e
PageioflS ATTACUNEIT A .e24", W-c. IJ-r-1 -'7i.
4 mu FARS 9 or Up
Iteim No.w: no.B.lO0 PressrizetSm plin Nwzle tSheHl Weld N&:.: WP26-1 scan Plan Nozzle Surface 2
- Base MeW Examined with 600, 60ONS and 450nles.
600, 60°NS and.45°Chc scan 3.1"
-I
,,,l Shel
~.* ***x x N*x~
N XX " X~X N .N .N .N .N .N .N .X .N TA CNN[M ITA
-TT eIG va
itemNo:3B31O09 Weld No.: 3-.PZR-W26.-
P uzer S&Iing Noze to Shel Mr. Shell Sc Plan e
-. ii-n..'
Ba..M ta-amine with 600, 60oNS arnd 450 an..
Nozzle Surface 2 6 0 esnd 450Circ. scan Shell Sur ace Page,*~i
- 9of:* 1i8 AITTACHONEIT A- Li-f i2L- "-'7'
St*eR W No.: 03B.11O.0009 Pressrier SlinýýNe to Shell WedONo. WP261
- Total Weld Meta Examined with at least 2 aingles, rom one direction.
A combination of 450 and 600 angles ere used to obtain COv.erage
%Examined from Surface =7.015/l1.413 x100=61.46%.
64.3% of leno*x 61.46%ofvolume = 39.52%o f total' SI weld coverage
% Examined from Surface 2, CW,4 and CCW = O0/w Unpered surfae was present for 18" of 28" of total weld circ 18128x 100 64.3%
45._
I Shell Surface I
- X%, X TX , X. K%Kx X T xX T - v .1. -V .V ATTACHRNF -
- 10 o~ I.7.015sq. im./ ~eu~h ~f -7 MAE 17,OF J(,
Item N.' : . 0* 110.000 9. Pressurizer.Smp.i "Nozeto Shell HMr. Shell e Weld N0.:3FRW6-i-A combination of 600& 70. angles mere used to obtain a dkimum armonut of coverage on tapped surfa. Nozzle
%Exani.ned 600 and 700 =3.03 11.413 x 100f26..55%. Surface 2 I, 06 35.7% ofle x 26.55% of volume = 9.48% of total SI weld coveW."
60 Tapered..sre was present for 10" of 28";obftotal weld 028x 100 =35.716
)
41, I Shell 1 Surface i'.*;i..=
Pagei ,,, ,8 x* ' xx -x x Nxx x x xx x x1x 11 xx.
/
.3.03.sq.in.-
ATTACIIMEUT A'~'~-~
PASEV'3DE ck,
Item No, 3.3llO0 Pressurizer SamplingNozzle to Shell WedN M.: WP26-1
-Total Base Metal Examined with at least 2 angles -fromone direction.
A combination of 450 and 600 angles were uased to obtin covwege.
%Examined (24.45 + 5.705) 144.87 x 100'= 67.2%.".
643% of le.gth x 67.2% ofvolume = 43.21% of total Sl base metal cverage.
- tapered surface was present fr 18" of 28"of tal weld idiumfere 18 /28 x 100 =64.3% 60 '
450.
...... I 24.4* sq. in.
Shell Surac 1
- eLZ ori2 18 5.705 s.inAUEI..
Weld No.
..03;B3.flO.0009 Preurizer 6apl0 Nozle to Shel Hr.Shell e
ý3-PZr-WP26-1
- 60& 70 aes were used to obtain a maxinm amout of Acnof corVae on t*ppered sur&c.. No27Ie
%e a j600 700 24.22/45.83 x 00- 52.850/o.. Sirfkce2 35 7h* of length x 52.85* of volýme = l .*7o of tot Si coverage.
600 :Tapered sufaqce vs present for 10" of 28" .ofttal wemld chamferenc 10/28x100=35.7% '. "
o:.Shell 162sq. in. 6-..--,.NE,
.Page.. ' i.
0:
Item No.: 03.E3UO.0009 Pressurier S n Nozeto Shell Weld No:WP26-
- Base Metal Thamined with 60" aij 450
% mined 60and 450 = 19.03 / 44.87 x 100 42.4%.
643% of length x 42.4% of volume = 27.26% of total CW/CCW coverage Untapered sface was present for 18" of 28" oftotal weld .Iduuv=6LLA0f 18/28x 100=64.3%
60nd 45°01c. scan 19.03 sq. in.*"
Shell Surac 1
\:XX -' ~ X XX ~ X ~ X X X X '. X X X X X XX X X Xl X. X. X. XX
. i Xi X i Xi Xi Xi Xi XJ X 1 I 14 o~'88 44r- MAE 1ý OF 5(,
0
!Item No: (3.ifO.00 *:*
9
~~ *
- NoPressurizerSg to Shell . Shl Weld No.:. 3-PZ-WP26-1
%Examined 45 and 600 11.85/45.83'x10= 86%/.
- 35.7% ofl x 25.86% of volume =9.23%.of total CW/ COW coverage Noz*e eed surface present for 10" of 28" of tothl weld r Surface 2
. 10 28 100. 35.7%
o
- -ag.
,..:60ind 45*Circ scan / Fl:..
- . .*.S..:..:::~~I
. !.s.:
- ..s- . . . . . ... . . . . .. *..
~
?i;:ii~i:.i Sh. .-
iii!ii!!?
- w. "'
. . . -. . }. * :
t,-'.:.\.,.:.. \ N \ X x. T . T*.\ T .. ,x
. ..... '.. . : . . .A T T A CH.
i:,*/ *::: :*:i :sq . .M NO::: ,0;* fi B? . PA61 hOEII
Weidi:oi,:!i*,
WP26-!:
Item No..: 103B1O.0009 If i ra Nozzle to Shell' Base and Weld Metal Examined with 00 an&'ll
%Ex:m.ndO- 0 =19.03/56.283x100=33.8%"*
64.363% ofllegthx33.8% ofvolume= 21.73%6ftotal 0,coverage, U.ntapered
" surtfie was t for 18" of 28" oftotal weld cderence 18/28x100=64.3%
no
.i-.
- I 19.03 sq. in.
Surface 1 X NX K T. IZ--Z K K It ICK ICT K X-r K \ (z tcoeebvith r tJ.C>.j ATTACHNEIT A Cp4r i IDIaC i Ub Iw
Pressurzr fti zZle to Shel Mr. Shell F
Weld N&.: .... 3-...'
.... :.:..... !,..:f:... :
JMW% PExained wmi 0111.85/57.24 x 1oo00.7 .
..35.7% of length x 20.3% of volume = 7.39 % of total 00 coverage*
Taperedsf was present for 10" of 28" Of total weld cirumference
.10/ 28 x 100 35.7%*/
.1
- !::Shell
[ II t - - - -
I I . . .I . N N x -1 11 N
__J -f.
11.85 sq h,.
AIIACflMENT 4 Page ' of is -7 PAUE fq OFI&
PZR Sampli]if Nozzle to. Shell % of Coveragee d
109 Item No.: 03.93.110.0( Weld No. : WP26-I Weld Coverase * * .. ... LL
- =r
=
Stan n % Coveraee Obtained ca S1 450 & 600 39.52 +
SI 60P & 700 9.48 =
S1 Aggre! ate 49 S2 450& 0 600 0 CW 450 & 600 CCW 450& 0 Total S 49 49 +4~. 12.3 % Coverage
.... 'ase Material Coverame Si 450k& *: 43.21%,
S1 600 & i709 18.87 CW & CCW on ta,per 9.23 CW&CCW on fli~t 27.26 Total 98.6%
98.60% +2= 49.3 % Coverage 00 Scan Coverage 21.73 + 7.39 29.1 % Coverage Aggregate Coverage = Weld + Base Material +00 + 3 30.2 % Coveraie
. ,p I Date:
ctor ,-
- Page.... L Ab Inspector Dat.B Page Lgý of ES:
UT Calibrat l&mlnatlon su nit: Ocorm.. I1 3. .Procedure: ?~D544O Outage No-, 03U.
i* :*: *:*iWoikacopels:
- .:* S Report No,: UT-12-46.
'SI WoricOrder No-. 01955420 Page: I of
- 2.
Code.:. 1 = 00rooA Catltam: V" 183.110: L.cao:
Drewing No. : *IU-OCN 02 .eaalpt* Nowl to Shell C ooe ID: 3.PZR.wp26-2 " .-. e-gt . MIA . . CSl .1561NA mlta*t*,lo: Y . ed shiet*d,
-Beb.t .": Finish e ixis SearchnUnit l a' If.cre . Dabt I Axa Orlentated Search Unit Serial No.: IOTJT*
. Serial No.: J10022tSP) C lIbralton Si pe Sweep Sou n P ath Manuactirsr~ KRAOTI(RAM ER Manulctiur:* KBA Reflector Amplude % Dll.on S,, 1.0 Shape: R-... lieSBON to 1.50 lW Frq.1MHz 'Intr.cat.j~ , .231 msoi" tOH 70 =a 3.3 .-' &-
ars Style Gamma ft al.... : .133 Piler High Usam Angle: 0 aotU~menwi Single K.
Iapng ROct .0% Final Cal 1410 47201212 Mode: Long. -
Rep. Rateh,: rmTJz F'"oeq..: Meaured AnOl:. VI"A Couplant-
- Fitter. Fixed. 'mode. Pt Wedge Style: Intmigral SCal, Batch: 11225 CRecmfena OrmentaeSearch vn Voltage:, ." ie ..... O-e-u . F-:..,uli ve Type: uLRA 11
,EL Caibmilen Signal Swee096 Ax. Gi*n.d*) 32.
. Ciro.:G .R .in . MIA Reflector Amplitude % Divlls" ondPt Search UnIt Cable SMfg.: Sn*otchh
_-Sý*. 1VI.0 bof Sound Path~ Type: FIRG-174' MIA
.fxam Batchl 11225
- Uneaifty ReportNo.: *2, Lkeh S" No.Comm. 0 Type: ULTRAGEL 11 Scan Coverage ' "g.: Sonota, Calibration Slack
,al. Bloici No. 40338 upstrezio Downsteami Scan415 4.8.0 RaetarncaefSimulator Block Reference Blok Th.nijmsa 7 - la.: Flat .. CWO COW(:] Scan.d: NIA 1.. DI ....
,-.,Y.. .... * ,-.. . . _ __A ,a . .: 964= edalfafln .a.nlhAnmfotlt .1 DOZsion i SudPt
- .......... #%UEWKU i ,1 5 .. 0 1i1.0 1 Camp..Temp. so Temp. Tool: MC.MD*40128 Swic Cnsl,* li*o: As Ground ecorda-le (atio.n(): YesQO No B (WYe Ref. Attached Ulraonlc Wka"mR t.)
Reiult*m: Accept C Reject info - . " Comments: Referene Report UT-12446 for applicable limitation -
data.
ecetO C Obtaed 0%: No Reviewed Previous Data. .,.
" ATTACHNE-T /
PA6E It Of it
D TI)UKE POWER COMPANY ISI LIMITATION REPORT -.
ComponentlWeld ID: 3-PZR-WP26-2 Item No: 03.B3.110.0010 remarks:
0 NO SCAN SURFACE BEAM DIRECTION Due to nozzle configuration
. LIMITED SCAN E0 1 0 2 C9 2Z .1 w ccw FROM :L. N/A to L N/A INCHES FROMWO..W Toe. to Beyond
- _"_,,
ANGLE: 0.0 [0 45 .060 other FROM ..DEGto 360 DEG-
.:4 0 NO SCAN SURFACE BEAM DIRECTION 0L LIMITED.SCAN 031 0 2 [11.[12O' (3cw [*ccw _ _ _ _ _
.FROM' L ____to L___ INCHES FROM WO _ ___to ___
- ANGLE: .00 045 60 other FROM DEG to DEG N SCAN 10 SURFACE BEAM DIRECTION:
0 LIMITED SCAN 03 1 0 2 1'. D 2 3 cw . ccw
.FROM L to L INCHES FROM WO. to ANGLE: 45 . 0 000 other FROM, DEG to -DEG , "
o NO SCAN SURFACE BEAM DIRECTION C LIMITED SCAN E01 0 2 E 2Q [-ccw cw UT-12-M4 FROM L ... .. to L INCHES FROM WO " to Sketch(s) attached 4
ANGLE: .0 0 5 060. other FROM DEG to DEG 0 yes QNo.
Sheet. 2 of 2 I. Date:
ATTACHHEITA 0i PA6E2ZOfH.
0
UT Calbrati aminationw SOcnee 'Procedure: ND2o Ou" ge.No.: 03.26 NoProcedure -2 Rev.:" 7 R No., Uiro124 ii Code: ajtm oain Daraw"N.II.OCN3.u0 Descrdption: N.'we to shoo System 10:; $0 CompdeI 1D,ý .MrWP144 .aw. ,i MrLethA T"' nuter CS! 6.1861 NA Lirnita*io*
ons : **i; ao: mtl hee*m StaT 111s Finish Tane: 1213 Infru:Aq*t:Set ag - : -. Search Uni, - -
. Cats Axial Orle.t.t..d Search Unit
. eiSal No.: O.,i.T , .26704 Serial No.: Checks Callbral11n s inlow an, 7.A 7777-m
.al KRAUTCRAME.R .r Manufact... n, I. I. Cal 1049 412
- 212 Reat. Amp,.l.de S Sweep Division 1STM - ..
Mod. USN 4o Size: . I.o Shape:: R t.. Inter. C.. 1/11 s0 1.4 2 .25 '
ea . *. i:-;11.31 an : 1.0=" .2.25 MHz Style: Gam a ier.Cal. 1133 ' 3520A01 C.... .f P Exa. Angle: 45 #o.. em..nis: I Csý 1I Inte 31 h.036- 4 7 Damping: .K R*CL Ao 0% : an--- Shea, O ._l- .. _ i .6 ,.60" Rep. RaW. AutOhigh Fq.: 22 ~ Meapsurd AnP.ige________ Coupwaa VII 46 6L0 2.201 F:: ! ilt * .i Fixed Mode: P*!Ee:..... Wedge Style: SWS: C atch: 1 . rcu rntl Orientated Sewh Unit.
,Volt*' ge: Fixed Other- :.* Fudiwave* . .* Type ULRAGiELII " Calbration Signal Sweep Ax.-Gsin(dS): 463 CLt. Glaln.1(dS: 4.2. Seaamh Unit Cable . Mfg.- so'notach Rellectur Amp~wde % DivisonSon &
.-. S*c*n isoundvP.t =? 1. Inof Type: RG. 174. . .. tc " -'A-_-_'_.__"____. --
fa Btc 11225 Llneaiy* t Report o.4.: LI,2.20 Length: r No. Conn., 0. Type:. ULTRAGEL - -.-
- CaL-:* COL lbratlefi Sl338 B~k*.-Temnp.-70-:-Temp.-Toolt.--MODB401zS-----ESzr*ua~m: upte~ ....-- Cowntar~geOJ, Mig.-
nSReeenetlckhernoirua
.- ,-:-_._._ ,I"1,,- ' lc .
Thcý Wa CC W 8Md- GL3ro Sleeanelcorlnptd slow Sleap k o ndPt Thic es.. e. Fla .. .Y . .. - .n~_ Serial No.: 96452 Clomp. Temp. 80 Temnp. Tool. UCH0140126 Surface Condftowu An Grewi..! Wauu O A 2.0 Recordable IndIcation(s): Yes " M No (IfYe Ref. Attached Ultrasonic Indication Repot)
Reslts41"64:Accept .e)sc 1 info " Commlhen: WA Percent Of CoverageObtain*ed 0%:
W No N Revird Previous Data: Ye...
Stauffer. Lest. " . .4.... . .
'*.. -.IW.A!.:
ri.Sbl, David.. .e7**'-
. . . . .- < ., ,. .. . . * . .._h ,l Oer LvlN/A .5 -Date NRtla Dale 0ATTACHNEUIiA
?A 6E23 OF1C
- i:*Slte:
i nl nee:
UT Calibrationamlnatlon 13 Procedure: KDE4S20 ONuboo No.: 03.0 03.891110.0010 PricedureRv.: Report No.: UT-12448 QUMiii SyW..
.181 Worc Order No.: o106i420 POgW: 2 of Is ICoe: 1928I2000A
- Cat/Itm: 84- 53.110.':"IIIi Drabng .No.: iSI-OCNS-002. Descuiption: Nozzle to Shell Sytm III :II10I Com~poent D: 43-Zr-WP26.2 Stoe/laenth WA Thlcknessarnslemea CSJIO.IUINA U*Lmltain :Yes.-See ttichod lheet , StaotTbe: 1118 Finish Time: 1213 Instrument Settings Search Unif*. T~e Dt AxIal Oead Search Unit
. - . , No.: . OOTJXT Serial No.: DIR93N Ch:eks Caibratlon Signal Sweep Soun P t Y:Manufacturec. KRAVTKRAMER Manufacturer K13A Mal Cal ION 4 212.. Reflector Amplitude % Diuson M o:d....
-_ USN-4O Sus: fixI.0 Shape: mRebt. Itertt Cal. Its 80 1.2 1A4 Delay, 14.0W44 Range: 2-.0* m-.: 5 MHz Style: ,mm. AnW.lCaL 1153 4121012012 218 30 L.6 .5.5r jm'tWtleL .126 Pubwer High ExmAngle 60 0 ofa 21 20 4.o s0 "
itr Camnt:.l8nl 141i 1021 a:I.
o upn: 1K .,Reject: 014 Mode: Shear ",, Noch s60. 5O 12.10 .
Rep:Rate. Auitomigh Freq.: 225 MHz Meamured Anql. 6
- Couplant .5514 7.0 lUG' F:::l?: :Fixed Mode: PE Wedge Style: SIS . Cal. atch: 11225 CftumfmntlM Orlentaed Search Unit i..:::
Vjý:
- v oitage: e (dB
- d : O1W.
Fixed. 5;"
Puliwave T.YPe: ULTRAGrn. 8I Calbratlon Sign" SweeP A. Gain U5.: Cie. Gain (dB)
SdB 5. Search Unit Cabl ,. Mfg.: Senetot Amplitude % DlvlSlon
- 1. S. Dv. . 2.5 In.of SoundPath WA Type: RO. 174 . , Exam a 11225 jk:lna:ty Report No.: L,,2-200 Length: V No. Conn.: 0 Type: ULTRAGELI' Soan Covmeage Sonota"h.
UMg.:
Calibration Block COLIa.Boc No. 4"33 .Upstream Do cwntream "dai. .u5 R n.ferencllmulaor Slkof Thlcka- 7 : ,Die.: FIat CW o CCW0 Seanidl.w.i ~ 942 Gain Sina I Seep Sound Pai
... I : 1. 'am*,,,*" '* m- T"Inl- Seria No. 964 -IdB RlelrAn&oe 1Dvso unuua*
37 r'R u so A .
C-mp. Temp.
Recordab le lnditl*n(,):
Rea6UltE:
60 Temp.Tol:
Accept. Q Yes Q R6je1M MCND03401 28 No [
Info Surface Condition:
Q)
As rendam (if Yes. Ref. Attached Ul*t*rsIc Indlitgn Report.)
Commnwts: NMI
+i'-1 .8I I+
PerentOf'..C o .eraO.:..:ie.d::9%,No"eie.
- iou.Date'"_*_"_" Pre.
-?A6EŽ'1 flFU
- 0.
UT Calibraticamination-
- ,: ýi1. . . .... . *. . . .
P S4GIIeJInt ()*ones SProcedure: MNbme. Outag No.: 0.2.3 .
Summary No.: 03.133.110.01010 Oromdure Rev.- Repor No.: U74.l2448 Waricacops:
- I!Y;
- .Iyl' /i..i...; .?;.i.i ..
IT"" **""fl.,*
Code: .:.Cattem:
Loca:.m.
om.oe...: 3.P W.... --
NIbA ThlIC eluilametenI C i681 NA Umltaia: ;IYeaSee attached heit :. """Stea Time 1118 Fbidah Ti*me 1213 I.:.jrI entrSuetlngts .. Se h Unit' - U pp _____________________________________________
Seirl,, No.: y0TjXT Seoral No.: oIRMN . . WWJ TimeO Date Axial Orientated! Search Unit -
Matuiefucturar. KeR .. .. -chocks 1148, In',er.-CaL -10,,01 u m ,. . cal~braition Signal
. _% wei D~vesn.
Model:: USN40 Iniia Cal 1053 41201201 Reflector Ampgkbid % OlVial Ieat Site: .5x1.0 Shape:
- Re.t.
- " Freq.: 2.25 Mz .0 2.0 1x M C" : .. .1268 . Pueer.
Gamma S..UCal., 1.0 70 4.0 .
High E., gimeA: g 1 of E . e ingle Intr. Cal. 114. r -
Damping: Relct 0%uore _____________ of 1.1 55 9.0 3.0" tlngI Cal 14181 41201201 20 40 1
. Rep. Rat:. 4Autohighh .. Freql: 2.25 Mll Measred Angle: Be * 'r ul.r e. .Otr" FFMter 15T so 7.0 3.42-Fixed Mode: j. -PE_ Wedge Style: Sws Voltagme Fixed Other CaL Batch: CIrcumfornell.Orluutdd Search Unit ,
" Fuliwave 11225 A."GaLc(d): 56.5.. C. Gain (dn) 6.5 Sa Type: ULTWAOL 0 Calbratbio Signa % sweep Unit Cable Reflector Amplitude Divalon W Path I &:Men...- Div.. . S.unda.*.h Type: R. 174 .SeeAxial iUneauity Repott Na: L-12.266 Uzm Batch 11225 Lonotu . No. Con,. .
yype: ULTRABIEL U
,. ll" .. .o"b , . k . . *.n ge ... "a . Mlg*- .S-oncsch cal.Block No. .40338 Upstream QDownstream R Sea dB: 70.5 h".!i:m10 .7 I. .:. Fla CW I Reference loeek Rference8llmullaor Bloek CCw 0 Soon 4e: 70.5
". Soft No.: 96"522 'ea nm s* n " sw e p
- . '. ". . " e Camp-Temp. ad.. Temp.-Took MCNDEAOI28 SmpstoCondlllon: Aernl
'I -.A~J Reflector
.*IJ& I*r- MIIMIIII lAzupitude1111
%I Division I ~
i AI "1]1 i e* H
-- l-. I I
- I I I I
RecordableInd' t yesQ. N0 (if Yes. Ro. Attached Ulhresi Indication Repl") I I I I I I 1 11 t t .' .
Reslts Reject: .e ,,,nfo . I I I I Comments: WA*
P
..:erenm0t
.:: OfCoveg mm:Obtined >:, 0.%.": .... No... . Raviawad
,,. 0,,ln. *lt~
Level lUdSinturypapWpe 90%:te o aa Exa.inerLevel .
E m . b w;.. . .... .-.. :.' . .... ::. .....,.
......... Davi -:~~~~
....... . .,...'Stm * .- -* . I---
. . ,: Al - .IlO% ... RSit l J. 1 mt e Dl
-.:.*,=*
Otheffr 1* ....dLM;":*evet l lm NI '.
- T.- / i . *"+m . . /. Dt. .. . . T* -- * .,_ ,, " - o~
rNI .M. l.
.sgntr
..... . :...... . . DoSP...:.:.... ,N. rwmolw" .
WAWM in u i i+; ;.i:*.:";.i ii:!+ .:..;"
Al IAEHNHLUI A-PA6EZO8Fj&
UT Calibratioralmination I Summary No.: o03Z .110.0010 I 3~Procedume P Rv'.
- N0EPOO 7
Outage No-,.
ReportNo.:
03-26.
UT12446 Wokscope- 18m.W#ik Order : 01055420 Page: 4 of * .18 Cde- ': " " 190 2000A C.aL/iem: 0 11 10 oI.ais: "'
Dring N-. 1S1CN302 De....pto: NeIs to She I.
System ID:
80 . *"
Componnt ID: 3-PZR-WP2e-" . SIuenath WA ThickneaelDlameter. CS I 6.15 IRNA LUmlItatons: None , StatTime: 111 Fnish Tme: 1213, Instrument Settings Search Unit "T Axial Orientated Search Unit.
Serial No.; O0TJXT SehiiNo.: F21r74 C-"nks Calibration Signal Sweep 'Sound Path Manufaclurer KRAUT..RAMR ,==12 Manufacturer KAaE 100. Reflector Ampitudl % Oivslon
,M i ," . USN4 " Sie.: lxI Shape: ".nRo d te. l.
1/4T SDH s0 2.1 8.5"*
elay: 19.118. Range.-: 26.00i Fq.: 2.5 MHz sw.a ,aau, -Cs . 1- = 012 1/2" SN 20" 4.0 1.10""
MdUCalWOl .126 Pulser High Exam Angle: 70 0 of Elementin. S!ingle- Inr"Cal. 314T SDH 1010 6.$ 16.30"
-- - - - - I - = I -
bampirvg IK. Reject: 0% Mode: Sheaaral125£2021 ID MNa 20 7.6 2l.WO' Re. Rtoe:po Autei Freq.: 2.25 M.z .M Angie. 70 Couplat 014T SON 1 10 1 0.4 26.60 Fllfitr- Fitxd Mode: mPE Wedge SWl: SIS ;Ca. SBach 11225 Cireumbront Orientated Search Unit Voe:v, F owe.
hixed Fulevo T.yfpe.: ULTGL it Calbron sw Swe so pa Ax. -Gain (dft- .667.5 0 .8CIc. Gain (415: W NA Search Unit Cable Mf. IVteec Reflector Amplitude %~ DI Path ScenIv 2.80 B .In. of Sound Path Type: RG 174- . gxm Batch~ 1122t WA LineaityiRpolNo.: . ..12-00 La1g4": " No.Co.:
C . Tye ULTRAGELU Calibration Block Scan C-,ra" ... Snte
- ik.' . N______o. 40338 Upeatm Q Domstrem Ea Sean d,,: 05 i -k, R*af*enceflhlulator Weoek
.7
.ik tmaI r Tmft , f, r lTl Thfd unuwnr Fl*
Pla m
,... CWr R.m*,,,l CCWO Scan n
-*"..e., N.: dB IRefletrAmltue% DWIOMonSun Pt I qua *~nuuuuuI uw
-. tI .-
U., I
~ --
£.UV aw U.1 . 4rw SCamp..Temp 601 1 Temp. Tool: MCNDE4012S Sur*f*ae Condition: As Greund.
Recordable Indication(s): Yes Q No (IfYes Ref. Attached Ulrasol lndic R""w.)
lcoi Resul:o Acce.pt.o Reject , info C] Commen 6s6.0 801) ref. 620 to achieve secondary DAC 314" Q 60%
PercentOf Coverag Obtakind*0 0%: No Reviewed Previous Data: Yes: 514T Q 10%1775 primtery ref. notch to "AC.
ATTACHMENT A MPAE N DF'?'
F DUKE POWER CIOMANY ISI LIMITATION. REPORT ___
omponent/eld.ID: 3-PZR, WP26-2 Item No: 03.B3.1iO0100 remarks:
0 NO SCAN SURFACE BEAM'DIRECTION Due to nozzle configuration.
LIMITED SCAN [I1 1 091 0cw [K__m.
FROM L: NiA to L N/A INCHES FROM WO Toet. to Beyond ANGLE:. 50 0 45 0 60 other 6ONS FROM 0 DEGto 360 DEG
.0 NO SCAN SURFACE PE-AM DIRECTION Due to nozzle oonfiguration.
0LIMITED SCAN 031 .02 0 1 O 2.cw 0ccw _ _ _ _ _
FROM L N/A to L N/A INCHES FROM WO: Toe.: to Beyond _
ýANGLE: .0 0 C] 45 [5 60 other 70 FROM. 0 DEGto 360 DEG C NO.SCAN StJRFACE BEAM DIRECTION.
- o. LIMITED SCAN I' I 02 01 C cw
.- E cow FROM L .. _" toL___..__ INCHES FROM WO .____" to '_,
ANGLE: 47-0 0 45 060 ot r FROM "DEG to DEG
..**. -.. NO. SCAN SURFACE SBEAM'DIRECTION 0 .1.0 2.V ,* 13cw LIiMITED"SCAN [I 1 E2 UT-I2-948 FROI MAL "_ toL INCHES FROM WO _ to. Sketch(s) attached
- 4 ANG~LE: 0*0:.0 5 .. ther FROM. DEG to DEG 0 yes. r No Prepa .:4t2M12 Sheet 5 of 18 I'.
Authoized lrnsp"?,ý, Datw:
AITACRKERI ft FA6EZ'76Fq<,
Item No.:4 03.b3.11O.OO SS Nozze tShell Htr.Shell
" -~scanPlan:
~e~of IS M~E 23SOF 5&b
hei. .No.:e '30B3.11O.OO10
.Pressu r S1.g Nozde to Shell 450& 600 0 Weld No.: 3PRW2- ScarOPiat Suffice Distance Measuread from OD of Nozzle Nozzle
-. '"Total Area Coverage xamined with at least.2 angies firomone direction. Surface o'2 k A combinatin*of 450O 600 angles were used to obtain a maxnium amout of
- ,:"i.*.i.-.:.":"'.'
.cove..ri."a.g..e.*
16.88"
".12.41"-
'i I
I AN 50\ I I
I 45Q. 6600 NiSN, I I
Surface.1.
VN T I\ T IZN N N x 7 N I IN N
- ATIACUNEIT 4 Pae7 ofJ8 LIT-PAGE2?D F 9 4-
It6mNo..
N -. HUM Pruriz to Shell Wed-No.. . P26-2 S611 Plan
,,,Base Metal Examined with 60, 60NS an 4506*
600, 60 0NS and 450Ci.sc.
3."-
Shell Surface 1 ATTACHMEIT A-
.~ 8"'~
FARE 3o Ofq (
0 i .
PzrSaffpln-Nozzle to Shell Htr.Shell e
WedNo.: 3-MZ-IAI26-Base Mea Examined with 600, 60°NS, and 450 a**.
SrNozale Surac 2 2.4" Surface 1
~eu ~-4 ~"
- AIJACHMENI A-ae of i 'JT
- P IE91. F9r(
Item No.: 03...*.
.. 01. urizer ling.Nozeto Shell WeldNo.: W2-
/. .? ...- * . .: . . ..
Total Weld Metal Examined with at least 2.angles from ohe direction. Nozzle A combination of 450 and 600 angles were used to obt*ncOVerage. Surfac 2
%Examined from Surface 1 7.015 11.413 x 100=61.46%/o.
64.3% of length x 61.46% of volume = 39.52% of total Si weld coverage
%Examined from Surface 2, CW, and CCW=6.
Untape.ed surface wa present for 18" of 28" oftotal weld'circumiaence, 18/28x 100=64.3%
600 ACO IShell Surface I
.~
~e~v~k ~
7.Ol~q~in./ ATTACOMENT,7 7.015E in. sq.,
0
&o be r~
Item No, 011-0.1O0 .P'ssuzerS Noze to Shell Mr. SheO" p Weld No. : 3-PZ-WP6-2 Si`.MW A combination of 600& 700 angles were used to obtain a maximimanamout of coverage on tappered surface. Nozzle
%Examined 60* and 70* =3.03 /11.413 x 100= 26.55%. Surface 2 600 i 35.7%,o of lengthx 26.55% of volume = 9.48%/of total Si weldpoverage.*
.Tapered surf.ace was present for 10" of 28" ofotal, weldd cuferenc 10"28 x 10 =35.7%
- .i.
I:
II I
Shell
.Surfce 1
ý:'% N N . NN-.N 1, 1, X, N. N X NN 1 1. N
~/
- " 3.U Page.' of. .:
MAE 33'OFY~41
Pressurizer * "
-to
,S iP6 iel.
. WedNo.: WP26-2
- Nozzle OUrIacc Z Total Base Metal Examined with at least 2 angles from one direction.
A combination of 450 and 600 angles vere used-to obtain coverage.
% Examined.= (24.45 + 5.705) / 44.87 x 100 = 67.2%..
64.3% of length x 67.2% of volume = 43.21% of-total Si base metal coverage..
Untalpred surface was present for 18" of 28" of ttal ,elddircumference 18 /28 x 100 =64.3% .60
~45".*
24.45 so. in.**_
24.4-5-so. in.
Shell
". rf...
. .!1 f
~e~wd 4 yo-.. 5.705 sq. / AITACIHNEITA Qw.4 1%
Ii Pressurizer SAmPh -NozIe to Shell Mr. Shell 0'
Veld Nob: 3- IPZRWP2
.Acombination of 600& 700 angles were usedto obtain a axinumamout of c:-:overago Surface.
e on %tppered Nozle Surface2
% Examined 600 and 700 =24.22 / 45.83x 100*= 52.85%.
.357%of letx 52.85% of volume = 18.87%of toa Si coverage.
600. Ta s .e pr for 10, of 28* ' of total weld c*cumfenc I S/2%8 x*100 =35.7%
I K
Shefl S*.r. ce 1 1.60 sq. in. qA1TACfKE.'l .At age~fl t2ý,evv PABE35-9f'z6
Iten 0B3.1O.O1OPressurizerk No: Samli- gN~l to.Sheil Wed:".:
Ite : .
N.....o. . . .3 ... .3 . . A ,
.P26-2 Nozzle Surfaice 2 Base Metal Examined with 60* and 450 angles.
%Examined 6O0and 450 =19.03 /44.87 x 100 =42.40/c.
64.3% of length x 42.4% of volume = 27.26% oftotal CW/CCW ooverage
- Untapered surface was present for 18" of 28"?ftotal wedcue c
- i!':*:i(
- : - .-. 181[28 x100=64.3% .,: .:
- Wan : 0.~45°Cir. scan 19.03 sq. in.
- ~~~T .E :-1
- N..- 1.
- ~~~~~~. .. .. 6E..*.... CF'.O NNN XN,N &Z: 3'"
N
eO
,
- i I fItemýN 3B.OO10 Press0r"N**A Nozzeto Shell MrLShell W0id No.: 3-PZ-M&26-
%:j0/5O(:()O *45o/d60* 1l.85o**
11..5/45.83x100 =25.86 *oA.
,35.7%/~,of length x 25.86% of volume =9.23%of totla CW/ .CCWcoverage Nozzle Tapered surfaewas present for 10" of 28" of total weld cirdafrwence Surface 2 10 /28 x 100 =35.7%
6O0 and 45Ol r scan i
i-i Shell 11.85 sq. irL ae ofý ISe C1G t%:,t9 ATTACHRENUI A MAE 37 OF
N.:U3B3 Ite 10OOl Pressurizer SipiiNo leto S iell Weld No.: WP26-132 Base Metal Examined with 600 and 450 anW
%/oExaminedwith 00 = 19.03/56.283 x 100=33.8%.
64.3% of length x 33.8% of volume =21.73% of total 0' coverage Untpered-surface was present for 18" of 28" oftotal weld iu 18 /28 x 100 =64.3%
,I 19.03 sq. in.
Shell Sur~face 1j N N. N X X .X X ' . .N .N .N .N X N .N 1~. ATTACHMENT A U. ~ lB PA6E 3ODFO
ltem'o.:03.33.110.0010 Pressuzer Nozzle to Shell Hr. Shel D Weld No.: 3-PZR-WP26-2
%Exarni*ed with0= 1.85 / 57.24x 100'-20.7/%.
35.7%/a of length x.20.7% of volume 7.39.%:of total 00 coverage. Nozzle Tapered surface was present for 10 of 28" of toalweldc Surface 2 10 / 28 x 100 =35.7%
O*scan.
Shell
- S :1~c 11.85 sq. in.'
PageOf It ~ATTACHHNET 4
- ~Ct MAE 3' Of -1ý
PZR Samglin2 Nozzle to Shell % of Coverage Item No.: 03.B3.110.0010 .Weld No. : WP26-2 a-LLI Weld Coverage I&I Gfl I
Scan Anele % Covermee Obtail'
%. . . . p loer. ......
Mvu Si 450 & 600 39.52 +
SI 600 & 70P 9.48 =
..S1 Aggregate 49 S2 45° & 60P Cw 450 & 600 0 ccw 450 & 600 490 Total 49.
49 +4= 12.3 % Coverage Base Material Coveraee
" "S 450&600 *.43.21%
SI .600 & 700 18.87 CW & CCW on taper 9.23 CW & CCW on flat 27.26 Total 9&6%
98.60% 2= 49.3 % Coverage 00 Scan Coverage 21.73 +7.39
-- 29._ % Coverage Aggregate Coverage = Weld + Base Material + 00 3 30.2 % Coveraee
- . n h...I .
£LA~jJ~~LUR I jJGL~ ff AE~ij~
- 1'-2" I~
.- . 7 c -.. Page 19 of 16 i.i * .
.i? :,,
UT Calibr2 kam~hition 3 Procedure: #%D403W Outg No-- 03o .-
!:!;iii::*
!/! li* *;ii~i!iWor; Summrnny *lcac op:
No.: , 03..3.110.0011 Pocdureftav-.. pmt No.: UT.-1244 181 Weak Ord&r No.: 1sa 4 - 5*
Code: 191"a.120M L Caltsmer: 3-0 )"l10 i6t~a iSI-OCN 3-M.0 d..ngNo.: Descplpqon Nbxle toShie.l System. ID: A0 Compnen ID 3-PR-W264SkoLenglft WA Th~nSMIs1Dmatsr~ CS 16.18181 NA Umttos See attached shgot
-e.S StartTime: 1103 Finish Time 114
- ... amen. Settings Search Unit Serial No.*: . ' JXT "e... NO.: J19022*1CPhecks Axial Orlentdod Search Unit
- -. UTKRAujILn'., ."i 110261 4-M oW12 Calibravon Signal Sweep Path Model: A I.
Reftetor AmpAd*e % Division' sta.* 1.0 Shape: : CRoud aIl.." L.
80Iw.
3.0m.. Range: 10.0" preq.: 2.25 MHz Gamm " Cstyle
. 4t 12 I/e SON so .o 180
..2/8 SOH4 7O 3.3 IX Mi Ct . ..... .u . . High Exam A-..ngl: 0 -of ....... ,nle r t.
VIT8VIIH 6S E_0D" vsmplng .IC
.*te Rejeti Lon Final Cal .120 4I.W1MO21 70O 658D~
R."
.Rate: Autohigh Freq.:. 2.25 MHz Measured Angle: N/A *. -- I -- I couplant.
Fler! Fixed M*ad: PE Wedg St*e Integral Cal. Batch.
I : i .
11225 Circumferential Orientated Search Unit Votge: Fixed- Other. Funfwve" Type: ULTRAGEL It I I Ax..GA..(d) 32.0 Cird. "ainjd8). .N Search Unit Cable Mf*.: Sonotech Calibration I S Sweep Division 30%intl Path
. Screen.Di .=1.0 mof Sound Path Type: RG.174.
e ExamBatch 11223
.... .....wsulReot
. . No.:ix...
. ' .. . . .. .0,* V.. No. Cor.* Type: UI.TRAGEL U
..C.librat.on.B.o.k.S.....
... . B ... .*.. er.. - o ci*. Block ft. . . 40,38 Upstream Downstream a Scan dB: 48.0 ,
- ReferenceBlc RefereneeSilmulnlor Block Thickmnes 7 Die.: Fiat OWE,) CCW: ScaO.: WA Cal. BIl.Te.,mp. 70 Temp. Tool:
-SealINo.: . 9452 GdBIdReflector ~Ampltud. %I Owaaen Sound Path MCNDu28 c Exam Sfboe*: 0.*.
Camp. Terp. Temp. Tool: :MCNDE412U 'Surfae.CondWon: As Ground . BWs m Uw .01 10 Recordable Indicatlon(s) Yes Q No 1 (i Yes, Ref. Attached Ultrasoni rde W60on Repoit)j Reu~lt: Acpt. Q Reject Into QComments: R. fermnce Report UT-12450 for applicalfe limilation did of.c..cov.erw d 0%: No Reviewed Previous Data: Yel.
....... ... -Rev"iew Site Ad:i beI*:,Oa: W::.
othffi!:::,!;:;*,* LOW.::::
WA:::,
'00 AIM DaW: AKI ,Piwe.w*,*J.
PA6Eq BF q4-
a ab
....-DUKE POWER COMPANY ISI LIMITATION'REPORT.
Component/Weld ID: 3-PZR-WP26-3 Item No: :03.33.110,0011 remarks:
" NO SCAN SURFACE BEAM DIRECTION DWe to nozzle configuration
" LIMITEDSCAN 0 1 02 *"1 -2 cw' ccw FROM .L. N/A to L N/A INCHES FROM WO Toew to Beyond ANGLE:::: 0D0- 45 0.600 other FROM 0 DEG to 360 DEG.,
O NOSCAN SURFACE BEAM DIRECTION O"LIMITED SCAN 0 1 ['2 E1 2.: cw D .cew FROM L to.L INCHES FROM WO. to
- ANGLE: .0 0 0 45. 060 other FROM' DEG to DEG o NO SCAN SURFACE BEAM DIRECTION CLIMITED SCAN C]1 5 2 0 1'1 i. [Icw. Ccw
.FROM L _ _ to L INCHES FROM WO. "
_._"-_"_to- I_"_"
ANGLE: D0:0045 060 other FROM. DEGto " DEG 0 NO SCAN SURFACE BEAM DIRECTION QLIMITED SCAN 0 1 0.2 -. 0 1 r2' cw. C]cw UT-12-49 FROM L to L INCHES FROM WO '___"" to ._Sketch(s) attached
-ANG.LE: 0:0 .]5.0 60 other FROM-
- DEG to DEG Is yes 0: No.'-
Propared By,.y.**.
- Lester,* *a*Level: III .Date: 04"*12 -"Sheet'2 o 'f
.2 A.ITACHNEI A-0 MEAGE
UT CallbratitLjamInatlon S SlteiUnit. Oconee 3 Ouhta No.: 03-26 542 Summary No.: 03A,&110.0.011 P oedure Roy.: Report No.: UT-I4O50 Workwo*.: 1.
5is Work Order No.: ' 01i Page" 1 of '1 Co6e: 199 812000A Caiitem: .. 5.0 13.11" Loatcon:
Drawing No.: .SI-OCN3-002 Doealom. Noaiie to Shll,
-System ID: So Comnporwe*nt.,: 3PzR-WP26-. "N..Il.engk WA Thlckna/alqemete 0816.1161 NA Umitaution: Y.sSe" s ,lat*t*ahdsheet. Start Tim: 1108 Finish TIme: 1148
- Instrumento Seage0 Search Unit Se~a o. OTJXT 5njljft4: H26734 Choc-
~ Calibration .Signal SAwep 8 u a KRAUTKRAMER Munufactur. Ti li Cl11030 4111201 RtflecWe Amplitude % Division
.... .... U....Sie:~ . . Sape:. - ac.a. " .a 1 Its i0 IA 1wr Delay 11.31. Range: 15. Freq. 225 MHz Style: GaIIoi1 3w1 3.0 70 MU. Ca" et: .A268 P*,ae, High Exam Angle: 45 Sof laants,: mingle I!Lnte . -. -
31 I 20 4 ,8 " 7.0o Daimnping: 1AK... Reject: ... 0% mMo*a I. 411r12012 Nlotch I 36 6.6 S,8O" Rep.ft t.:.Autohah .. Feq.: :2.5 M Measured Angle, 45
" s 'i $-.: I=2W Filtana. .- .. Fixed Mods: .. PE Wedge Style: SWa. Cal. Bitch; t*225 ¢Ckouberantlal Orbenttd Seach Unit iVoge: .. Fixed Other. Fultw5ve *. . -'Type: ULTRAGEL I1 A:c.IGain (dB) 48.3 CIsc Gain (dB) CIoraIon sinaw Sweep or 46.3 Search Unit Cable Mi.: Sonotach Reflector Aupi % O a .lo ,
_.ad. .
I roahf Div 1.5 Sound Path Type., R -174 Exm Bitch . 11225
.Uns Report No.::
n a..t.yily L.-12.200 ...-JZ V. No. Conn.- 0 Type: ULTRAGEL I Calibration Blwoc us" C w.30. ft: $Sonotech Ca.L:B.40
. . N... ."...":... upstream Q Downstream Ea Scan do: ; * , IO Referenasil~lmulator Block T-hi::.:
kn;am* ' T "Dla.:
- Fisto* CW* CCW2 Scan do: 62.3 S . "4822 Gain ' Signal SI See sound~PAM CaJ. B. Temp. 70 Temp. Tool: .MCNDE40128 Exam Surface: O.D8..* U-.
Comnp. Tep. 180Temp. Tool:: dCNODE40I28 36 2Rad lus s_ 4 '.0 Surface Condflor As'Groud R*crlendlctiton(i): Yeas No Ea (If Yes. Ref. Altached Ultasulat lIndlooaal Repart.) .
Results,
- Acce Rl.eje:
pct Into 0* . - Commints: NA Percent Coverage
- f Otaed*f* Go%0: No Reviewed Previous Data- " Y"s "
Exam.I . . . .. ... .a. . . Sa Review Grlel*d*t ii M. 41.112012 01A NM.
- NIA-.
LeVA Ither
. Sig RD I jI *4).....tu.L~I%.
Re"vie PAGE q3OF 144
UT Callbratiorcamination Oconee .1 3 Procedum, O No.: 0341 Summary No.: 0s.3.0110.00111 Procedure Rec Report No.: UT-.21"5 Workacope: 181 Wo*kOrder No.. 011115420 Page 2
- of II.
Codex 119=82000A C Dt tItem: NshOl.oSha
- s:
Otawing No.: : mISICN31402 Descripton: N=e to shel Sysemu.l 1 5.0
'Component ID: 3.PZR4.WP-3 'SlLeneft, NIA ThlCI Slea TimeUNI C4 16.1 88 IN Umitatlone Yea -S.30attched shee,t *start Time: 11108 Finish Time: 1148 MINOR ii urn I F i.:.;: .5. ...i:: - -Insr ment etinge sarch Unit -
I Seral No.: .OOTJXT Serial NM 01R1N...
Manuticturer ~ IRAUTKRAMER Manufac I<;KBA,
.,I,.0 Shape: Reft.
Oe! ? 1:4.044 Range: 5A " F " -. .2 ,MHzSy: Gammi MID eIVeI: .1268 PulW. High Exam' ,g. so #of Elements, single K
Aang Rj*eaf 0% Made: Shear Rep i.*tt.. :..Autohlgh Freq" 2.5 MHz Mesauf dAngle: 60 Allter Fixed Mode: PE Wedge SWS CaL.Batch 11225 . Circumfoeretil Odentated Seamh Unit Voltage: Fixed Other Fuhiwave Type: ULTRAGEL . Calibration. sown Sweep un Pth Ax.
- Gain (dS*) -56.5 c. Gain (d,): 56.5 Search Unit Cable "M. .4 U"ftEW.II Reflector Amplitde DMalon 1:..Scree. . n Di. In.of Sound Path Type: RG -174 Ermn Batch 11225 S.. Axial _ _J S'e.'ty Repodt No.: Lo12-200 V No. 6mn.: 6 -Type:. ULTRAGEL II Cal;.. ..Bt.okN..u Calibratlon block sra Scan Coverage ca .7. sroet"Ih cai. WoNo. 40338 0 puhi3,Downstream S0, dO: Referenc.l.*.Ik Refelnc*l~lmulater Block.
Thikn-w, 7 ie.: Flat CW, CCWl o,,di,. 70.5 s ,,,o. ______ Gain Signal Swe oudPt CaL W:k Co. p. Temp.
Temp. 70 Temp. TOOL, RecordabeIndication(s):
80 Temp. Toto:
Yes Q MCNVI40I211 MCNDE40o28 No Exam Surface:
Surface Condo=
O.D.
As Ground (if Ye, Ref. Attached UlasoncIndldReo.i T
"'l""rn1t' 39A *_Radlu, 60 4.2 12.06
- eeultk Accept Q Reject 0 IfQt " . Cemimantr w p4
- Percent Of CoverageObtained :> 90%: No Revie Previoua s Cat: .Yes.
i~mir Level DwSgauefatb Revewlý Signsture Dabe StlaufflelrDv': Leste, Exmaminer 1M.
Level IN 114d Sluohir m 4/111,/1013 0015 8*
b*~i Signatue 3o ' iltl Oatm Orlebel. David M.
- 901W 411202iI O rLe - l MIA
.a 'a. re
. NI.e
/v D-/-OW:
vi.. .
.. V
- A~TACUMEI1 4-
- +:, :
':." ..' i:y.:..
(ii 4 S
UT Callbratilfkamination pig "UN SltoIUnlt: Oconee I 3 NDE42O Outage No.: o340" Summry No.: :- o3.53.11.00o11+
Proced.
J Rev.: Repast No.:
Workacope:
- " ." ".. * . i81 . w rdio,,.:
Wor
- 7 0.im -t UT.12-S50
,-9 ,~
..- Work
, O.,..r.N..
- .AWO --- ,l Code. :IB:o.
199812 114 Ca 1.t¶o Looalon . "
Oto.wng No.. I81-OCN3.002 O:sstlft. Nozzle to Shell SysemID so 3.PZRW-.. Spon...: SheLength: MI Thldomneaulan*eter. CS 1I6.118111A Ya.i "a attached shee
.Um.t.ona: Sta'tThw 1108 Fish Tim" 114 Instrument Settings Search Unitk ME . --'TM CaL illl.l'1*
TM a. Date Axial Odlentated Search Unit SIN.]: ; 001.JXO T
.Sera No.: oIR93N chec k . . . ., Calllbrllon Caflbrto ,o ,,.*SWOOP
,uP l* ll Man_ _ __ _______e__ _ ta Cal *05 4119W2r12 I*l*dePSCI r Amp % Owlon "
- M~ode SzlimusNS.0 WSiz: Shape: Rel ' so.... 1.2 6L4r D2 Freq.: 2.25 MHz Se Inater. Cal. Ila$ 4110 201..
MUCa~L 168 Pdsr High E~mAul Emn Angle.
o So lmna ingle Cal._ ____ --
Damin: 1K RejeL& 0 Mode:
so.a Sheer of_.. ",mols
..3Notc 90 60 4.0 9I5" 12.10 Rej;. at Atohigh Freq.: 2.26 MHz Measured A*gle: to l 6 Is,,"* 7.0 1.i Filter:. Fixed Mode: PE Wedge Style: - W8.. - ,' aLBatch: 11lCsmsntl Orlenated Search Uni V.og .ullwaiteFe Other Type: ULTRAGEL 1i CajibraiJon sweep AXGain d3)X- 5,4.5 C. G(In (d0):: .54. Search Unit Cabe M . .enetech __o____ _ _% -on sc:agý Dlv. i 21 --
2.5 L+ot : -Sound
, . ......Path Type: RG - 174 a m Batchl 125 11225 A Unealy RePort No.: -.12.oo Lingth: w' No. Conn. e0 LAEL "
NO. .f:* n Block Scan Coverage . Mf: Sonotech Ca..4.
___wI__a_____ ,tok,___ _ cwB: 6.'.m Re-fn Rolnte2ncSlmulnOr Block*
~Cl Te 9k7 Tm.Tol Obi,"i TW .O CNDE4OI2U Excam Surfs"e: C 240.0.
S6"B: --1RWeeSraNo NW " 9652 "mIlI dEB elco RelereS.eed AinofUtde n I OMalon:1e S4IdP" Comp. 1ýmp.. 8 Temp. Took 'MCN.ED0128 Su .rface Condition: As Ground 3I9rR o . -
RscordaWe Indicatlon(s):'Y Yes Q No t (lIt es. Ref. Mac~had Ultmaonic lndlostlon kepedj
!* ? koc 00 Reec f.ia 0 Co nsf: MIA Pement Ofovege Obaed50% . No RevewedPrevious Dat: . Yes sintr' aeSignaueDt e, ai M, Ire Signatue Oats
'Dvi 401.9,111012.
Dab
- Uanat DataANOeIew S s D-at
.. : Laval... .WA.
- Pats ATTACHMENT A-P. ARJE(5OFI&'6
0**.*.* ..
DUKE POWER COMPANY ISI LIMITATION- RZPORT.
Component/Weld I: 3-PZR-WP26-3 -item No::- 03.B3.110.0011 0 NO SCAN SURFACE BEAM DIRECTION El LIMITED SCAN 0 1 02 0*10"D2 O;]cw[;<ocw FROM. L N/A to, L N/A INCHES FROM WO: Toe to Beyond ANGLE:. 0 .0 45 060 other 60NS FROM -.0 DEG to 360 DEG.
.. NO SCAN SURFACE BEAM DIRECTION 0 LIMITEDSCAN 1 0 2 0 0 2.. 0 w:Cccw FROM L to L INCHES FROM WO to " , _ .,
ANGLE: 00 0] 45 0] 60 other FROM DEG to -DEG C NO SCAN SURFACE BEAM bIRECTION 0 LIMITED SCAN lI 0 2 01: rC]-
2 fl cowcw
[3 FROM L to L INCHES FROM WO '"_*_" to ""_."
ANGLE: 0 El 45 0[160 other FROM DEG to DEG 0 NO SCAN JRFACE BEAM DIRECTION
]
El LIMITED SCAN C [ 1 i... D E2 . Dcaw , UT-12450 FROM L to L INCHES FROM WO to Sketch(s) attached 4 .0
,ANGLE: 000 5 03.60 olthe rt FROM DEG to DEG. yes 0 No :
III ATTACHMENT eqt-
Pressurier i Noze to Shell 450& 600 e Itei No.: 03.B3.O. 11..
Scan Plaf Weld No.: 3-PZR-WP26-3 srac Diti*c M*,asued ro OTIof Nonle w
bzZe E; Total Area Coverage Examined with at least 2 angles f.Qm one direction. rface" S.
A com*binationof 450, 600&60 0NS angles we*.e*us.to:oe btainama),:mu arot of
.. ,covage.
.. .. ,. . ... , , , , *.. ., , ,16 .8 8" 12.41.": I
.. 450 /
450 '600&60N
- " :6:" .:"i.: . :.*:':'"*
00*.. :: " .3 ~-
i*,,*i****
ii:'::*
- ,i: ...:::*::IL 17- ......
... S.u!*
rf*hell 1e ATTACINEUI 17 If er A
Item No.::... . .U.. Presurze Sa*)InbNozzletoShell d No*o.:: WP26-3.. ScnPlan' SBase Metal Examined with 600,: 60NS and 45?
600 60)(NS[ an 4S0 Cire
.4 Surface I 4
\<1N\ -' ý".'X-X N*N XX NX' XXX
". 1, Xý "" XX X X " X X X N X X X N N X" 11 -
WETACUMEI.I P.(O.i4'~Ar-I
It "INo.: 03B 110.0011 P.Ri.n.zer SN0"Z'e to She."
p° W: No".:.WP&-.3 NozIe
-Weld Metal Examined with at least 2 angles from one d:ec.o. Surface 2
.:A combinaton of 450 and 600 angles were usbd to obtW cove=rag.
%Exained fromSurfie 1 = 7.015/ 11.413 x .1.=61.46%.
%.Examined.f-oSurface 2, OW and CCW.=/ "
674.
Surape. 11
-ATTAC jN9jp in PABE 4~DF q~,
vT-
... Pressurizer S N. to She
- .'.Weid:No.:: WP26-3 Nozzle F= Total Base Metal Examined with at least 2 aiýie from one directSioane A combination of 45 n0
- w4 e w()e used to obtain coverago&
%Examined =(24.45 + 5.705) /44.87 x 100 =67.20/.
.. . . I.
i-;:~ -~) " .. ~ of.
- 450 99'
ItemI Weld
-o.:WP26-3 Pressurizer ,,n,,igNoIeto Shell e il Base Meta Examined with 600 and 450 MI'
% xm~ined 6O0and 450 19.03 /44.87 x 100 =4140/o.
0 6 *w45O*fc sca
.19.03 sq. in Shell Surac 1:.I
- X , 1. 1, ATTAHNI ENIT PAO6E~t DFIq %epoA
?ItI*No.:: 03.B110.0011 PrurizerS pngNozzle to Shell Weld...
N.:WP26-3 Nozzle Surface 2
"-.I i "Baseand Weld Metal Examined with 00 angle.
%ExaminedO° =19.03 /56.283x 100 33.8*%..
0.0 19.03 sq. in .
- m *
...ShelU Surface 1 ATTACBIhOA-
~%-1O~r~ I~
0
- O.ii! PAHEýtOF9c,
ttNpShell % f C Nle ~Verage, PZR- Samnf~
ItemNo.: 03.B.11O.0011. 1*#qd No. :WP26-3 Weld Coveraee S.b.
La.h Scan % Covermee Obtained "a I-Si 450 & 60* 61.46 am
$S2 450 & 600 0 Cw 450 & 600 0 ccw 450 &600 0 Total .61.46 61.46 .44= 15.4 Base Matemal Coverase Si 450 & 600 67.2 U cw. Ccw 45*- 600...
Total 42.4
... .. *10o9.6 -
109.6 - 2 = 54.8 % Coverage 00 Scan Coverage .33.8 % Coverage Aggregate Coverage = Weld + Base Material +00f .3
. : , :- . i; 34i.
" i.7 ' . , .- d m.-?s
%Covetaige I.. pe.. to Date..-: ~i%
UT Calibratio*4amlnation
.3 Proedr NDE.40O Outage No.: 03-40 Summary No.: 03.53.110. 001 2 __ PrqcidurM Rev.: 5 Report No.: UT-124I1 Wo..:*cope: 181 Work Onr No.: 019"a42 Page: 1 .of 2 Code:~ 199=000A Dedplt: I- o JM3.110 D: aw.ngNo.: .. i81-0CN3402 System to: 60 CImpollnlnt !PZR-Wl26*
D i 7 S .e/lngth: N/A ThlgimeoslarWamter. CS I6LIN I NA Umitatons,: Yea.- Seeatt*t hed sheet Stat Tlme: 1135 FiihaTkw: 1225 I --
" a.mnent
. . SetUnp search Unit - -" -
. ... NJXT' Axia Orientated Search Unit SerlI No.: J, Checks Manuiactumrer KRAAJTIRAMkR h"aCale11025n09= Ca~lbration Signal Sweep.SudO RsleCWe AmplMtud % Division Mode. : USN4. size: 1.0 Shape: Rund In eay 1.0359 Range: - ow.
10.0" Fre - M~.z Stle d e ICal. -"
I Inter. Cal. 12= 411WM20 li/S DH 2IM DH s0 To 1.10 3.3 1.4w 3r.
.. 2 Pul.e. High Em Ang: 0 9 of Elmwft: iine-.i 3il 8DN 66 I 5.00 D.mpn: 1.K Rebject 0% Mode: Long.
Rep.ý Rate.: Autdolgh Freq.. 2-25*MR Measured An _ _ ' Coupln'
".'"".F . Fixed. Mode: PE Wedge style:. " Ing Col. Batch: 11225 Choumfersentil 0entdd Serch Unit
.. .. - : .. , O ther goltg: FieF~r ullwave . Type: ULTRASBI. V Ax. Gain (dB): 32.0 Cm.Gean (dly WA Search Unit Cable Mw: Snetech RaORclecr Ampitude % Diviason
. "Screenv. in. ot BoundPath Type: RG - 174 EamBatch 11225 N/A o"110_. "
.L.Repo.t . No.: Length: V No. Conn.:: 0 Type. ULTRA.L OlRaftrannSIgulsow a Sloep Sw~oop Soun 00t CadlibrationSea Coverage.Uon Sonoteo.h cal. Block Io Thcicka ness:
f Dwp 4033$
Fiat FlCa Upstream Downstream 2- "'adBd: 48.0
- d. .-
- Setal~.:
Rfm lk 646=
c-0 %I*,-
Rsferncelmunator Bloc:
"*o I *
- Son Path
- '. Cal. .TSoTmp. 70 Temp.Tool: MCNoEa4028 ExamSurfawe: 0.0. " 12.5, SI II** No-o 1A *t*
COmp.1Tm. so Temp. Tool: MCMDEdOI28 Surface ConC5110mt As TYre: R0UP Recordablelndlcatlon(s). Yes Q No I .(IY", Rad. achad Ultrasonic IlodcA Report.)
R*.o-_ Accept Q Reject [ Into: "0.Ocinmeniw Sal erence Repoft 0 UT.12-12 fer appl*cable mIa ..
Percnt:OfCoveragObtained2,90*%: No Reviewed Previou Data: -Yea.
0 -. PA6E~yffqOF,
0,i~e~i D DUKE. POWETR COMPANY ISI LIMITATION REPORT_
iCOmponsntiWeld ,D: 3-PZR-WP2 -7 item No: 03B3.11060012 remarks:
O SCAN. SURFACE BEAM DIRECTION Dueto nozzle configuration El. LiMTEDSCAN I1 CD2 ED1" 1.2 0Cw. ccw _________
FROMW LN/A toL .N/A INCHES FROM;WO0 Toe to Beyond ANGLE:.: 0 00 45 060 other FROM- DEG to 360 DEG S0.NO.:SCAN . SURFACE BEAM DIRECTION "ILIMITEDSCAN .0 1 0D 2 0.1. C3.1 O [_3. cw_ __
.FROM .L ._: " toLL INCHES FROMWO. .to.
ANGLI 0.045 0 60 other FROM DEG to - DEG 0 N...ASURFACE .. BEAM DIRECTION QLIMITEDSCAN"El" 02 E}..['-3.2 [3,ww.-_
...FROM L _-toL t L INCHES FROM WO" _ . to "
ANGLE: :0 0 45.45 E60 other FROM, DEGto DEG
- )SCAN :.St JRFACE BEAM DIRECTION.
OLI MitED SCAN 0i:: 1 02 R 0E 2 2.-" to"C UT-12-951
- ~i*:!:
- R:
iev::
- qewed:
FROM ::N L __ __ to L .INCHES FROM WO._____ to ___
Sketch(s) attached 00*:'0 '460rl60
... 0,ther 7ANGLE: ther FROM DEG to DEG Oyes 13No' Prepared E AT TACH HEN I /I-PA6E5:51F q<.
UT Callbratloriamination .0.
SlteUnlt; Ocense 1 NOE4302 &OtPe No-: 03-36
- 1Summary No.: ____"_ .1edw Rev.: '
032S3.110"002 7 Repot No.C: UT.124"
- wrlmscope: lea. W~itl Ordei No.:i 0t19543l0 .pawe I of 11 Code : lW0* DA Cam:
c199 * .110oLemlo X& "
ra.ngN0.".: "II.)lM-0"02 ODscuiptlon N.i*z to o" "
System ID: 50 Component IP.: "IA S÷ M. ThldMasi~amets: Cs ISSINA Umtton: Yes- "e.tachedshetst Tim 1155 Finish Thme: 1226.
in*:-::,...:."
strum :::i:s FUnit- Se* Unit . .. T ime D f Axial Ortentated Seamch Unit Seulal No.: WrJXT Seial No.: H2679 Chc Ma.nufactunw. KRAUTRAMER MpAnufacturer Ca' rtn Signal Sw Sop peuh KBA Initia Cal 1030 Reflcto AmllpAude % Dhvslon Model:USN40 ie .a, Shape: Pea.. COL.
In3 81 1A 2"2 Delay : 1.1 Rang: 15.- Freq.: .5 MHz Stle: .'Gamma-e.a 1 1 1 215 35 , 4.70V
' C. .1265 Pulsar. High m Angle: .4 #of Ebniet.s nter.Cal. 3 20 4.1 7.L0
.. ,: 1K Reject: 0% d.: ser na .4 . 1 ' Not 36 U 9.L0D
. I: . Aui-talvigh Freq: 2.25 MHz Maued Anl: 4" ." Coupoot 01 It. U 1.2.W Filt Ftwed Moft Pe Wedge Style: sws CaL* Satch: 11225 V.lt96,: Fixed Othe Fulwave .Ype ULTR..EL It A"..Gain.(dB): 4.3
..I.. Screen Dlv. u 1..
Ckr. Gain ():
In.of Sound Path 46.3 Type:
Seairch Unit Cable ..
R0-174. :
.g.:
"mnB*.
Sooteh 11225 I~
Une:art, 14o0t6No.: ,..'-200 L 6 No. Con'.: ryp: ULT-RAOEL I
- ..,_ . __._.__*__._*_.*.*....... Type ____:____o_.
Cf-bretSoau Snek .CovCmgo . ,ig: Sonot,..
Cal. Biloc No. .40M Upstrelam Q Downtream 6a dSW6t 3 ..
,...D
- ,, . *11 i e.: Fe CW C CW....2 ' No.: -1 15=1
- C*a.k Temp. .70 Temp. Toot MCtNDE.4OI2 Exm Surtfac: O.Dy 'TYPC*I ROMPA4S
- k .. ":-.". *".:. , .. ..- " *.:--.:
- Camp. Temp. 8o Temp. Toot MCNDE4OI28 Surf"ace Cond,,r As Grounid
.. s.ordab1sInduletlon(s): Ye Q No Ea (IfYe. Ref. Afttchad Ultrasonic uIndlollon Report.)
Resuft Accept Q Reject Ea Info [ 3 Comments: WA Percent Of Coverage Obtained *090%: No Reveid PrAous Date: y. .
PHM5~ OFIO
UT CalibratI1 amination oClonee. / 3 N0E420 Outege No.: .03-.21.
Summary No.: 03.83.11o.0012 Piocedure Rev. .7 Report No-: UT-12-52 ISI WoekOrder No.. 01I55420 Poeg: 2: of .11 code: " . " C~atJIsm: PO5.1 Drawn No.: ....... l OCNS ,002
Description:
.kqu to Shin System1 : 5O..
C*mponent-1.: IO 3 MW ,2,-7 Skae/Lnbth N/A a C81.1651 NA Uimittons: -Yos
- see attached seet FiihTime: 1!225 1165 Finish Time: lZis Start Time:
lastitament Setting. Seria No.: Search unit Axial Orltitatad Search Unit.
Serial No.:; OOTdT N.:OIR93H Seia -ChecJ Cle~n Sga Sweep Path MunUfaCt..r. KRAUTKRAMER ManUkCbAurs KBA Md jCalIW .hV12, Reflector Aiplilbide % Divison
- .. M.d.l:USH.40 Si*e: .5x1.0 Shape:" L!! 1i" Cal.. ": E"Z. . o 1.00-12.0 Delay 14.0744 Range: 50 Preq.: 2.25 MHz Style: G"mma C&L 120 .419=2 1.0 70 4.0 2.0"
.. .:...:,. V. k .16: Pu.sen High Exam Angle: 60 Sof Wamenji: ingia 1.5 a6 6.0 3.0"**
0amp~g~. 1 Roj .0% Mode: Sheai ia a 13540'4/19/W20 2.0 40 U 4.0" Re.at: Autahigh. Freq.: 2.25 MHz Measured AMr , s - Coupaiat" Sla4r so 7.0 .s.*
- ftrFixed: Mode: PE Wedge St ows C.l. Bateh 11225 ClraumferentW Orientated Search Unit Votae: fixed Othen Fuliwave: Type: ULTRAGEL- Calibration Silnl Sweep Search Unit Cable M.: Sonoticb Reflleto Amplikide Division Son h ON.~4~ .3 lM of Sound Path Te RO., . -, Exam B 41225 See~x Linearity port No.: L-124200 Lengh: *.." . No. Conn.."...-. .. Type: '.ULRI, LIi
-Calibration Bl1ock Scan Coverage Mfg.; "" ontschi Block.-No.
.Ca...ream .03. " U (J Deebeam
" SCnW : 70.5- Rel,,n. ,loc RIieta ee/mulaaor Bock"
. Icknes:.s 7 Di.: Fliat "CCW. Scand*,: 70.5 Gain Sia Se unPa SWNo.: 96452 Cal. 8ik. Temp;.; 70 Temp. Took: .MCNDEd40128
- .: :.-..,:* * .,* .:o]..- '... Exam"..
.;: ---": ........- B*Ofao. ;"
Type: ."- A_
RO IEPAS
.dB Reflector. ~deV. Divison Camp
.;. Temp. Temp. Tom 1 M:...NDE41a1Z. Surice Condition
- As m,,und . S9A IrRadwsa so 4.2 .1 2.00" Recordable 16dc (s): yeas : o - (IfYe..*.R*ef uacadUltramac.Wnn*.Repo)..
L.
A"ccep
.tala 0 Rej*ct. .2 Into [3. Comments: N/i Perpent 01, Coverage Obtained 90%
M No Reviewed Previoua Data: Yes
.... jJ .II;
.... III* 7777 lure A f P
.. :... ,. . .w i i!*N :::: -::i.: . . ..IA.*..:: . .; I::i;:i:*
-,b 1:..
C.!"..
[ O
.:::.:~~~~~~~~~~~~~~
th e
"...* .7..: : ........ AT TACO NEITA?
?A6E *'r?Df 96,
UT Calibratiorcamina
- ND941= Outage No.: 03-218 Summ ary No.: 03.93&11O.002 kwwmeaw Rev.:- 7 Report No.: UTl4245 Work OrderW.: 01911420 Page: 3 of .'11 III Cod 11.912006A . Ca/Iutem: 3.
-B-p1113.110 wingNo.:2:
noia I. -CNo 0 Deacaptdoe N6=l. to $hell System ID: '50 C...ompnnt .:.....WP26 " StmaLapp: WA ThiclneaaOlarnater. C8.1 6.1881 NA Umnitalmon.: Yes - See ,Otsed ,,heet " Stait l imte: 1155 Finish Time: 12'25 I
.u.e.. SetiG.s Search Un - -
Sea. No.: o0TJXr Seral No.: 01PR.N.. Chec I " Axa Orwe!Atd Slearch Unit Caibrellon Signal Swep ound Path Manustcwuate KRAUTKRAMR.R Manudatkfrw KA.- inIU C31 '1035 4119120 Reolecr Ampliude 1 OlvIalon Moe:UN0Sies: _:=* s. *o
.Sxl.0 P:
Shape:* ,
Rqe. hiker Cal Intr Cal.* 111 .111 In 80so 1.2 3A-
"" ": .-14.0744 Range:. 2.0" Fmq. 2.6 MHz Style:, m 218 30 2.A ,s.
An CaIWal: .1268 Pulaer~ High Exam Angle: so #of EmmdLunne.Unl Cl-
.. .- 0%
.Rject -11 C 13381 319 20 4.0 U."
________ Mode:____ Shear Rep. Rate: Aut-high Freq.: 225 MHz Measu.*d Angle'.O '. 0 ." Notch so5 00 is 6.0 7I 12.10"'
16.8-Ftitat Fixed Mode: PE wed" StylS CaL Oatd 1111225 Ctemm~rmvs sOrtstatsd Search Unit I Vo taigoe: Fixed OtheW. Fuliw*ve . Type: ULTRAOnLI. L_
Sweep Ax. Gain (fd) 54.5 Crim Gain (dB 4.5"S Search Unit Cable. MW.: Semol.,, Reflector Amnlikude 1A OIVlSon Iound'Path t 9-ta I ScrenDiv.,..i.:;.":::Ex 2i In.of Sound Path Type: RG-174 """"225 Fxm S... lo" 11225 WA
- i.ea"L tyReport No.: WL12-200 LenIlh 6 No. C " 0 Type: ULTRAGEL II
-i~on e, Sean Coverage Mg.-: Sonee.'h' CaL Block No. 40338 UpatreamnQ DowMMstrem 60*9 nCI: 1.5 "" Refemancefflmulator Sleek Thickness 7 Die.: Flat CW & CCW0 Sewn d: 6-.5...s* ._ _ _
.".. Slt. Temp. remp.Tool T0 . MCNDE4OI2" Exrn Suitaee 0.D. Ty: ROMPAS a eletrAmpfltde % iiio Comp. Temp. 80 Temp.Tool MCNM540120. Surfac Conditlon: As ,out'"d so I 8 I Z IW 2iI Recordabli ndical"on(s): Y- Q No J (itYea. Ref. Atted Ultrasonic ,-dI*k=a Report)
.9 20j a jus Res".
.info
. Accept Q Re"e [3. C.mmnbt A, "
Percent Coverage P Obtained 90: No Rvwed Previous Data:
E1aminer6 ei
,.G41 ture ... . .gna Y"e DafaI R o Mj L./I
- .. :. :.:,.:. * ... .. 4.. AITACH NEEMI/#
MAE-59 If.,
U DUKE POWER COMPANY IS. LIMTATION REPORT Component.Weld ID: 3-PZR-WP26-7 Item No: 03B3.110.0012 remarks:
.... 0NOEAG SCAN SURFACE0S.6.: BEAM.DIRECTtON DEG Due to nozzle cpnfluration.
LIUMITED SCAN C0 1 0 2 I020cw 0 cow "FO L N/A. to L N/A INCHES FROM WO Too to -Beyond.
ANGE: 00 45 0.60 other 6OS FROM'_0 DEG to38 DG O1..NO S.CAN SURFACE BEAM DIRECTION UMIMED SCAN 0 1 .0 2 I E 2 ow 0 ccw.
FTROM L :___toI____ INCHES FROM W6 ____ to ___ __________
ANGLE..: 00 45 060 other F.ROM DGto DEG 0' ASCANNO SURFACE BEAM DIRECTION
-LIMITEDSCAN .0 1 [1 2 .0 1 02.'[ Cw [Icw c FROM. L NIA to LN INCHES FROM WO to .,_od ANGLE: 0 0 0 45. 60 Other FROM DEG to -. DEG SINO SCAN SURFACE BEAM DIRECTION 00 060 *other DE_
.OLIMITEDSCAN 1 0 0 2. 20 cw.)ccw UT-12.62 IFROM L: _ _to L INCHES FROM WO " _ to Sketch(s)attached ANQGLE: Q:OO0 6 060 other FROM -DEGto DEG 0 A:PrepareB o11 DOW 04/10/12 Sheet 4 of X.ReviewedyN SAN Date: AM DECTins Q
%j ATTACHMENTI "
PA6*E ofBF
iteimNo.:-03M.B3.1*OJ012 Prer Sampling Nozzle to Shell 0
- ,Weid No. P26-7: sca lan.
Nozzle Surface,2 Base Ml- &mied with 600, 60oNS and 450 as.
I 600, 60ONS mid 45oCirc.
" ' 3.1"
- Shell Surff=e 1
- .- .. . , 1 1 ý 1 ATTACHNENTI 2e.*LT~ ~ 2' MAEýo OF Y&i
Pressurizer 4S ing .Nozzle to ShelI 450& 600
..* . ... "O-0B3.UO.O.1-Scan.Plan WeldiNo..3-P.RW*26-7 Surfaw st Measured fm OD of Nozzle . F Nozzle
.TotalArea Coverage %xaminedwith at least 2 angles from one direution.. LA, z-I A.cminto of 450 ,60& 60WNS angles vwe ued to obtain a Mamum amout of coverage.
I 16.88"
- I A1I" 1 450
-. 60 i...!:..4::::i.
- urfac 1 ATTACHNEN IA-FA6EV( OF
Items No.: 03.B311O0.0012 Pressurizer Saling No4etoShell
ý:.Wel No.: WP26-7 Nozzle Total Weld Metal Examined with at least 2 nges from one direction. Surface 2 A combination of 45' and 600 angles were usedto obtain coverage.
%Examined from Surface 1=7,015/ 11.413X 100=61,46%/."
%Examined from SurfaceCW, and CCW- 0K.
60P 450:
K:
I
..Shell Surface 1 X N X X N X N X X X X % N'N" 1. 11 "Ill,% 11"N 1ý 11 I-7.015.s-Sin P4 . : -7*
0o MW OZf~Ite
ItemýpN............... *zr Slliflpliflg0NOZii*
Pressuzer to Shell WeidNo.: WP267 ....
Nozzle
,-:, ,,,,, ,Total Base Metal Examined with at least 2 angles from one diSfonae A combination of 450 and 600 angles wee used to obtain covepe.
%Examined = (24.45 + 5.705) / 44.87 x 100 = 67.2.
? :::: i/ .....
___ 24.45 sq. in.
ii ~~~~~H 45:0i:.:
- T.T \.N N TTT 7N 5.705 *sq 4..
.. 2.. Prsudzer SaplngNoizl to SheIl 0 i" .. WeldNo. WP26-7 Base Metal Exmined wvith 600O and 450 ngldes.
%Examined WOandl 450 19.03 /44.87 x, 100-= 42.4%.
600nd45O~im scan 19.03 sq. in.
Surface 1 11 NNN 1 X N X XXX XXýk 'INN XXXý1 XXIN
"'I XXX'IN XXX
'IN X -XX XXý
'~G~Td 4 Wt12 A~L.
TIACUMEIT k 0 PAl 9',.
z o I e4No.1 3.B3M.11O.0012.
Pessurizr P u.....
N Sa*pf.Nozzle to Shell 9.
Weld No. : VP26-7
.Base and Weld Metl- Examined with 00 angle..
%ExaminedO0 = 19.03/ 56.283 x 100 =33.ý/o..
19.03 sq. in.
.. l :
- Shell
.. r: c .1..".,.,'.
T T T IC\ -7 T KT
- ~TTACIIKEMT k 2arOO1 95.
PAIE~~5DF9~~
.PZRSamvlinif Nozzle to Shell %.of Coverage Item No.: 03.B3.110.0012 Weld No,: WP26-7 S.::
Sd~
Weld Coverage
.~
Scan Aniefe % Coverage Obtained 0-Si 450 & 600 61.46 .~ a.
S2. 450 & 600 0.
Cw.. 450 & 600 .0 CCw 450 & 600 0
.*. . Total 61.46.
15.4 61.46 -4= % Coverage Base Material Coverage
. 2 I~c.* 450. & 600
.450 & 600 67.2.
42.4 ToWal 109.6 109.6 + 2 = 54.8 % Coverage 00 Scan Coverage 33.8 % Coverage Aggregate Coverage = Weld + Base Material + 00 + 3 34.7 % Coverage Pag 2.
nspector/Date
. . . Page IL of l_*I.
.-.... .' S.
UT Calibratioamination ocon.. I 3 Procedure- PDI-UT-2 Outage No.: 03-20 Summary No.::
o3.B9.11i.01o6 Procedure Rev,: .E Rieort No.: UT-12463 i:*:!.*.:!:
,iW :;
- orkeco.
181I Work Order No.:
0195 Page: 1 of 7 CodeI 19082006A Catjitem: I4 /B9.11 Location:
. rawin. No.' 34.*A-1 (1)
Description:
Pipe to Valve 3CF.11 System 1D: 53A Component ID: 3463A-1 $45 Size*gt: NIA ThicknesslDlameter. 88 11.250 114.0 U.. ita.. tio..
.... : Y*.. d sheet Start Time: 090 Filah Time: 1009 instruMent Settings Seatrh Unit AxIal Orteztatmd Search Unit Serial No.. 0242D3 Selal No.: OFtTJO Ch*Gks CaEIbrtion Signal Sweep Sound Path Manufacture. A-Ma-lacturer. KBA It Cal 0.40 4M -12 Reflector Amplitude % ODvlon Model: UsN40oSW $Sze: .5 Shape: Round i ., 1.2r Notch o 1.737 1ela y:-
. Ir:::*i~~ . .0041 Range: .3.0" Fre,*- 225*.
Frlq.. M; Style ComAp -*a*:*... jn 0.. 0ON6 412712012
- i:: 2.251 Mz Style: Intr MCae: .1218: Pulser SqIuam Exam Anl: 45 # of Elerments: Single -inter. Cal.I ihl~n:: 5:00 Reject: 0% Mode: S1hear R.ep.
. R ,
110er otge Aut*oht Fixed
-40 F.M.
Mode:
Otfier.
2.25 MHz PE.
Fulkwave Measured Angle:
Wedge Se: MSWQC 45 Cal. Bech Type; 11228 ULTRARIEL II i Circumferential Orientated Search Unit Cesibwaon signal Sweep A'..Gin 12.2 C(dB)Gain (dB):'
Cic. 12.3 Search UnItCable Mill Sontec Reflector Anipilud % Divsion SonPa i Scen.i:.:.6 Dv.u - .3 In.of Sound Path Type: RG-174 Exam Batch 11225 See Axial Uneasily Reipo No.: L42-193 Len.th V ft Camt..
Soon Coverage 0 Type:
Mfg.:
ULTRAGEL ,
s"notee ,
I I I C.allbratlon Black CeE;Block No... P y-uA-O Uparew Q Downstream 1 Scan d: M R4ferc Bac3k Rferencel/1mulator Block Thlckness:* ..,37 -1.28" eDi.: Flat OW 0 CCW [ Scan dB: 24.3 Serial No.: 044743 d, AI Ampliud %Dison Refltor e
- ...CaL.8.lkLTemp...._ .Temp.3Tool: - .MCMDE40.1i2. _Exam.,u :_ _0J)._T . MP
- Conq. Temp. so Temp. Tool: .MCtDE401ZS Suface Conditlon: As Ground R dable Indication(s):
i.c: Yes Q No (IfYe Ra. Attached Ultrasonic Indletion Reope.)
- Rasuts Accept Q Reject Ea Info ] Commens: PulIae Width 220 ns ill $e11on X) Exam
- .--pentOf ove`Pge.Q4t4lned "90%: No " Revlewed Previous Data: No Ejoa**ý:': Level IýN Date Rovisow onto
,.Day.J, 412712012 Level. 041 Date am Signature Date Steven V27IM2 Other Level WA Date RA 0829 14A ATTACHNNEJ,4-PAGEOF 96
UT Calibratilliamination
" SiteJUnlt Oconee 1 3 Procedure: PDI4T-2 Outage No.: 0-.26
+:' :..:;.* .:.:.
- Summary No.: Procedure Rev.: E Report No.: UT-12-963
. .:.: ... ; Wod.woope: IS! Work Order No.: .01955830 Page: 2 of 7 Cod. 1998r2000A CaiJItAm: 9-J 199.11 Location:
aingo.: 3.A5 I)
Description:
pipe to Volvo 3CF.11
- Syftem ID: 53A Component ID: 341WSS15-26 Slzung: NIA ThknesalDIameter 5 11.250114.0 Umbltalona: Yea - see attached sheet . . . . .. .a.... I.. StaitTime: 1011 Finish Time: 1031 Search Unit Serlli No.:
sinstrumant Sefttig 024213 Serial No.: 03-782 CaL Check I I Axil Olenlated Search Unit
.. nufa .;u . . KRAUTKRAMER Manufacturer. RTD initialCal Model: USN,,60 SW Size.: 2(1!02) Shape: Rec, Inter. Cal.
Do*a 12.0647 Rtange: 4.0 Freq.: 2.0 MHZ Style: IRL2 IMh Cal:ýitIZ4 Puter. SqUISTe .yam Angle: o #QofElementa. Dual Dampfing .00 IRjec11t . 1 Mode: Long.
Rep. Rate:, Autohlgh Freq.: 2 MHz Measured Angle: 50 couplent Filter... PFled.' Mode: Dual Wedpe Style: Integral C.1. Batch: 11226 ClOcumfreindal Ordentated Search Unit oltage: 450 Other. Fulwa"ve. T, ULTRAGELU
,pe: Calbration Signal Swee Sn
-AX.Gah(dS) 51.3 Crc. Gain.(d) MIA Search Unit cable tfg.: Sonoatch Reflector Ampltude % Divlion WA
- I $Green DIV. .4 W of Sound Path Type: RG. 174 xam Batch 11225 ea. l.
- ::i:... ... No.:*.L*-L2-193 , i.li. No. Conn.- Type: ULTrAOEL 0 Celftration Block scaw Coverageh W: Sonotech Cat.":locic No. PDl-rT-TA-.O Upstream F] Downstrem a Scan dB: 54.0 Referanae Block Reframncelflnmulator Block Th-:i.ickn .37V 1.215 D-.. Fta Cw ] CCWO Scan dB: NIA werdl No. 04-8743 Gain ... Signwal Sweep Sound Path dB Reflector Ampitude % Division Ca-L9o Te*.T*.17. Temp. Tool: MCNIDEA412. Ewmn.S0we O.D.. rye: R*MPAS 4 - lRRIkii 1 -6 2:5- -1 0-Comp. Temp. 69. Temp. Tool: MCNDE40128 Surface ConldIonm . AsGround Recordable indicatlo,(s): Yes Q No Ea (If Yes. Ref. Attached Ultrasonic Indicatlon ReporLt.)
Results: AcceptQ0 Reject~ 0Info Q Comments: Pulse Width: 250 ne initial Section )U Exam P.eretOf Coverage ObtAIned v 00%: No Reviewed Previous Data: No i
ATTACIHEIT/
MAEa OF ?W,
F: slteunit.. Oconie .. 3 UT( amination Procedure: NDE4-40 Outage No.:
9 03-26 11.0106:
summrayNo.: :03.1119. Prooedure Rev.: 010653 Report No.: UT-12-063 SI 0155 Workscope: Work Order No.: Page: 3 of 7
- Cod*:: : :- 1998000A CatLtem: B-J 139.11 Locatw.
Drawing No.:. 3-63A15 (1) Doescption: Pipe to Valve 3CF-Il System ID: 5. .
Component ID:b: 3411-1-2S6 slze,*,,h: MIA ThicknessDlameter 88 11.250114.0 umitalons:: Nome Stan Time: 0936 Finish Time: 0946
- ,. - I - I I~
InturuentM Settings; search unit cal Time bhUnit Date Axial Orientated Be SerWa No.: 024203 Serial No.: 57452-08724 Checks So Calibration Signal Swoop und Path M: wfdactuemr KRAITKRAMER Manufgctmr. KIA iM Cal 0935 4127/2I Reflector Amplitude % Division Mode,: *usN-40 SW Sie: S.MXComm Shape: Round foer. Cal. so 8W 6.1 1,23=
9.i5 Rage... .2.0 Freq.: 4.0 MHz Stle: USES nter. Cal.
- .MCVl.a. .2m0.. Pulser. square Exam Ang* .0 Sof Elamentso: Dual nar. CaL._"
Dom1n: 5i0so: Reject:
- 0%* Mode: Long.. IaCcl 09471 4/=2/2 Rep. Rate:-:. Autjlilgh Freq.. .4 Mliz Me asured Angle: 0 Couplnnt F-tr...: Fixed Mode: Dual . Wedge Style: Integral C ai. Batch: 11225 Choumferential Orientated Search Unit Voltage: .450 Other: FultwaveT Yoe: ULTRAGEL I Caibratlon SIgnal Sweep ft Pt Ax.Gan (dB):-. .46.6. C Galn (dS): 46.6 bearch Unit Cable b us.: sonoteob Refle*to AmplWAIde % DivIsion Path een Div. la A"* I of Sound Path Type: RO..14E yzom Batch 11225 Unez eptNo.: L-..2-.,3 : *L,,igth: r No. Con.- 0 rype: ULTRAGEL il
.a'labratIon Block.. Scn Coverage 4U: Sonotech CO. 8l.. ... No.. Component Upstrea Do.wstream 9 Scan dB: 40.6 Referencs Black Reforonce/Slmulatar Block
- Thickness 125. DIa.: 14 CW 9 CCW Scan dB: 4.66
- erial No.
- 044743 Gain SII %I Sweep I Sound Path dB I Retcleco 1AMD11JUde % Division
- .Ccl.:81.Temp,. 77 Temp. Tool: MCNDE40128 Exam Surfac .0.D. 1 Camp. Temp. 63 Temp. Tool: UCND0140128 Surface Condition: As Ground rypo: ROMPAS 416"jW j
-Recordable lndicatiorgs): Yes Q) Moe (if Yes. Rot, Attached Ultrasonic Indlicetion Reporl.)
Reaulte: Accept Reject C Info 0 Comments: Initial Section Xl Exam PercenItOfCoverneg Obtalned 90%: Yes Reviewed Previous Data: No ATTACHNMINT A PA6E6.of OF? (o
0 DUKE POWER COMPANY ISI LIMITATION REPORT Component/Weld ID: 3-53A-15-26 Item No: 03.119.11.0106 remarks:
/ NO SCAN SURFACE BEAM DIRECTION No scan due to cast valve
- E3 LIMITED SCAN 3 1 0 2 0 1 IC 2 N cw 0 cmw configuration.
- FROM L N/A to L N/A INCHES FROM WO CL to Beyond ANGLE: 000 45 060 other FROM 0 DEGto 360 DEG 0 NO.SCAN SURFACE BEAM DIRECTION No scan due to location of
- o I"UMITEDSCAN [0 11 02 [11 ( 2 C3 w D ccw Pipebranch.
FROM L 4.0 to L 6.5 INCHES FROM WO 1.5" to Beyond ANGLE: Q 0 0 45 . 60 other FROM N/A DEGto N/A DEG o0 NO SCAN SURFACE BEAM DIRECTION E" LIMITEDSCAN 1 02 1 0 2O 0 cwC3 __w FROM L. to L INCHES FROM WO to ANGLE: 0 0 E] 45 0 60 other FROM - DEG to DEG
- 0. NOSCAN SURFACE BEAM DIRECTION I IIII IBI o0 -UMITED SCAN r"1 I1 2 0 1 02 0ew 0ccw LUT.12-963 FROM L to L NCHES FROM WO _____ _____to _ _ _ _ _
Sketch(s) attached 4 D No
.ANGLE: 000[ 5[106 ther FROM DEG to DEG 23 yes Pre.pared W Steve 04/27112 I Sheet 4 of 7
- Dat:
q.~5.1 .. Authorized Inspector Date:
ATTACHMENT Aq-OýZAe ~~M OAF(,,
Suppler&I Report Report No.: 4 9 6 3 Page: 5 of 7 Summary No.: 03.69.11.0106 Examiner: Day, John. C. Level: I1-N Revlewlr:
- Examiner. Dean, Steven Level: iI-N Site Review Z2/21 Date, Date:
Other NIA Level: NIA ANII Review.
Clom ments: Praoil for wed o3.53A-161-Sketch or Photo:
L ATTACHMENT A PAIE7(IDF 716
ReportReport No.:
Report: U 01-63 page:
6 of 7 Summary.No.: 03.B9.11.4106 Examiner. Day, John, C. LeveL I14-N Reviewer Date: I Examiner Dean, Steven Level: "lN Site Review: 0 A1 Date: ____
Other NIA Level: WA ANII Review: Date:
Comments: CoverageP t for weld 3463A-15-26.
Sketch or Photo:
ct-rcLuire46Cca t44-eY e
2 .s/qq'xioo:S4_ , MS~ c1ve(4 ATTACHMENT /
MAE 1-OF9~
Site/Unit Oconee I 3 Determination of Percent Coverage fo UT Examinations - Pipe i Procedure: PDI-UT-2 i r
Outage No.: 03-25!
I",
40 Summary No.: 03.69.11.0106 Procedure Rev.: E Report No.: UT-,124-3 . 91.
Workscope: I51 Work Order No.: 01965830 Page: 7 of 7 45S Scan 1 94.400 % Length X 50.000 % volume oflength 1100 47.200 % otal for can Scan 2 100.000 % Length X 0.000 % volme of length 10, 0.000 % total for Scan 2 Scan 3 100.000 % Length X 50.000 % volume of length / 101 50.000 % total for Scan 3 Scan 4 100.000 % Length X 50.000 % volurie of length I 0i . 50.000 % total for Scan 4 Add totals and divide by# scans 36.800 %totallfor4l deg (to be used for supplemental scans)
The data to be listed below Is for coverage that was not obtained with the 45 deg sca.s Scan I % Length X _________ %volume
% of length 1100 = _____ % totail for Scan I Scan 2 % Length X _______% %volume of length /100 a " total for Scan 2 Scan 3 % Length X _________ %volume
% ofienglhlt u __1__0__= " total for Scan 3 Scan 4 %Length X _________%volumeoflength/100=______ " total for Scan 4 Percent comnilete coveram Add totals for each scan required and divide by # of scans to determine;
. 36.800 % Total for complete exam Site Field Supervisor:. Date:
I
£i*I I,,i,,,,,, i ,i,, 7,, ,, l~)% 4 (pt.
UT Calibratioiamination Outage No.: 0,
.Oconee .. I .3 Procedure: *P01-UT-I Summary No.: 03.641.11.012 9 Procedum Rev. ik dN I.:
r.T124*1 Woftccope: Work Order No.: 01958382 Page: 1 of 7 Code: 199112000A CLit~lem: B-J A119.11 Loectiace
.Dmwng No.: 3CF-126 DeascrptIon: Pipe to VIve 30F-14 System ID:m S
- .Compone.. ID:.
. 3C. 2.. WA Thcknessa/Dieter: So I s.2 114.0 U~mitedona: Yes- 3eeAtached sheet S*tTime: 111I Finish Tlme 1200
- .:In..a.
... w:..".t Seulnge Sewch Unit Sole!* No.: oO pl SeOWe No.: 8E0355 Ue niilerure,. GE Manufacturer GE Model: USN I0 8W Sie: . Shap Round
. P W* - Range:.. Freq.: 2.25 MHz Style: Camp -aG Mu CAI .A1. 5 Puller S.quar 22mm Angle: 45 #o! Elementa: single
- amp :i 00 :Rejc o0% Mode: shear Rep. Rate: Auatchlihl Freq 2.25 MHz Measud Angle: 4*S CoupIant*
Fil:, Piked Modw. PE Wed"e Stwe: MSW4IC CadL Batoht 11225 Clrmmerentlal Orlienated Search Unit Voftw : 45.0 Oew. Fuhwave Type: ULTRAGEL II Cabeuflon sognl Sweep Sound Path Ax. Gal.(dB) . ISA. -hv. Gain (B):. I"A Search Unit Cale Mfg.: Sonotech Reflector Amplitude % Division
- I SeenD. .3 i.Of Sound Path Type
- RG - 174 l Se Axiad Exa Batch 11225 UneaityRqport No.: 195 Length: Ir No. Conn.:
- Type: ULTRAGEL A Caswbran Block camCoverage Mfg.: sonotech Cad..BlockNo. PO1 Uputream Q3 Da*e:tm a --- CS- Reference Block ReferenceISimulator Block Thickcness .37V5 -1.25 Die.: Flat CW6 CCW0 4an dl: 26.4 rial No., C4.3S Gain
,191 Leff.0.Sound Path CaL Bik.Temp. 74 Temp.-Tool: MCNDE40129 Examn Surface: 0.D. Twvn: ROMPAS 41.. I I p.
.* .. -Comp Temp. 71 :Temp. Tool: MCNDE40129 Surfa Condili:. As Ground I - I Rcordable I"dileto**)c.
Resubt Acceptj Yea 0 Re~ects No 5a (IfYes. Ref. Afached Ubwonicc Indication Reoi.)
InIo C LH~
Percet Of Coege Obtaned o 0%: o,N wou Data: No MAE 7YOF 94
- 'a. UT Calibratlo~ aminai Outage No.:
Procedure. PDI.T4T-0"9.11.0129 Proedure Rev.: Report No.: UT-12461 Wo.iscope. SIs Wok Order No- 019582 Page: 2 of 7 Code:. 1S9S9OOoA CadLmtem: B-J 189.11 Location:
Orawnig No.: 30P4I Descdpdotn Pips to Valv 3CF-44 Component ID: 3*-F4 2 .. SbW.nt: WA Thtckanes .meter. s3311250114.0 UmL i"atin: Yea.3 atUached sheet Start Time: 1145 Fnish Time:. 1200
":o ... " " .~.. eaa...--- * . *.s-- *
- sm. 0uun!9Iung mualull umui Cal. Thus Datw Axial OdntAWd Search Unit Serial No.: 023DPI Seri No.: 03-M82 Checki _
Calibetln SIgnal Sweep Sm s GU Manufacturer, RT i . 1 093 Reflector Amp&udo % ODalon Modek USN so0BI Site: 2( a Shape: Re Inter. Ca 4 O 1.25 Notch so 4.7 2AW De.ay "*72 Rang: w.. F-..r. .OMHZ stye: TRL2 lnter. CaL 114 21N
-Mi Cavvil: .264 Puian N3UM Exam Angle 60 #of aemennte Dua OaM.Inpng Auchg 8 Fm; Ra.ced 2Mo 0% Mode: Lon0.
FnlCl13218 162 Rep.Ra,,:. APPut,,.-,,e,, M, Measured Ange: so Fi,,a,, ed Mod: Dual. Wedge StyW Interal Cal. Batch: 11225 C111umfnrentldW Orbtd Search Unit
. o.ge:V " . 480 Othoer Pulwave Type: ULTRAMELI Reflt*etr Ampllhde % Sio Path Ax. GWal (0) .19".3 Cre. Gain (ft) WA Search Unit Cable Mfg.: Sonots.h
_Sr.n.A S . Path .174 Type:. R MIA
- i:*j:::,i:
- on~=,::,,. *ds ummL. No. Conn- Exam Batch 1122 U:"ad-.,Report No-, " '2.o, Length: v Ccn Type: ULTMA*,, U Caibratloun Ceekverage' Mg- sonte
__ __1___-__km__N__'_Tr-2 __O Upstream 0 Dom am 10 Scan dB: 64.3 Reference SBak RefornceISimutator Ilkck Thic.: ess .37V-10.2r
- Oie: Flat CWQ CCWQ SmcdB: WA Sedal No.: 0473 ea'n AmIus SI ISogund d8 -IReflector I~oltd Se "m
0Otwilon P" Ptath
,..Cal.1iTemp. 74: 'Temp. Too . MCNe400129 Exam Surface: O0..
71 romp. Too: MC,4PEA4012 surfba ConIoc . Ground As I~
-:-" -"Cmp.!Temp.
Recordable .IndctG8on(s): Yea El NOl1 (IfKYe, Rof. Attached U*ltascInllmon Repeat.)
Re..
- A"e:Ita. 0 eject, 0 Cnfo Pu Wkdh: 22"na P.ercentOf Coverae ObtaOed i. 90*6 No NRevtwed Pretu$a Dat, No Ia Seton Xl e ATTACHMENT ef PA6E "OF ? &
I UT Calibratio.amination a 3 Procedure: NDE-40O Outage No.: 03-26 Summary No.: 03.B9.11.0129 Procedure Rev., Report No.: UT-12-461 Wofia o o. Wok Order No.: Page: 3 of 7 199812000A CaLittem: B-J 159.11 Locstlon:
Drawing No.: .3CF-120 0es30p0n: Pipe to Valve 3CF-14 System ID: 53A Componen* .. t-, 3C.264 SlzaLenqth: NIA ThkiknegaDismeter. SS 11.250114.0 Lkmftations:: :None SMt Time: 1105 Finish Time: 1200 Search Unit
.:SelNo.: .023DPl Serial No 57463-1706 GE Mariufac hawr. KBA Mods*el: USN so0 SW t 3.5xl~mmn Shape: Round D.lay 8.18o Range: 2.V Freq.: 4.0 MHz SbI: MSE '
-M'U CalIer: .2252 Pulser Sut Exam A Via: 0 #of Elements: Dual Dam:.ng: .ej..t 500 0% Mode: Long.
Rep.Rate:
Rw Authigh Freq.: 4MHX Measumr dAngle: 0 Couptant
. Plte. Pl-.ed Mode: Dual Wedge IStyle: ~Intg raI Cal. Batch: 11225 Circumferentil Orlintatad Search Unit Voltage:, 460 Other. Fuilwave Type: ULTRAGEL II Calibration Signal Sweep Sound Path Ax Gb ~ 30.1
-:); Quoc. Gain (dB): NIA Search Unit Cawl Mfv Sonotaoh Refetor Amplitude % Division N/A I $ear:, I. Kn:of SoundPath Type: RG -174 Exam Batch 11225 Un"a"ity Report No.: " L.. Length: 6 No. Conn.: 0 Type: ULTRAGJ II nock Scan Coverage. Mfg.: Sontach Cal. Blocl.No. Component Upstream [] Downstreasml ScandB: 42.7 Relmme S RrentsSce/Simulator Block T.h;+
ic::,imess 1125, Oin.: 14r CW- CCW [] Scan dB: NIA Serial No.: 044735 I
- m , = __p__ GdaBI Roftector lAmcf'lntudeI1skp Sound Path
--.
- r I - i UflhIWA~ f....~ I .... I IIII I II
- IIIII--
-Cmp.Te 7 Temp. Tool: MCN.E..2- Surface C*ondro,* As Grourd i II - i.
Recodabe Idicaions): Yes Q No (If Yes. Ref. Attached Ultrasonic indication Report.)
ReIUlts: Accpt
" - Reject[ C In"to Comnmensts: Inith l Section XI Exam Pe . .rcent Cov,..
. e. Oted " 90 : Yaw Rav.owed*..evi.us Date: No AITACKNE11 A' PABE 7( IF 14
A. a DUKE POWER COMPANY ISI LIMITATION REPORT ComponentlWeld ID: 3CF-126-4 Item No: 03.9.11.0129 remarks:
0 NO SCAN SURFACE BEAM DIRECTION Scan limtation due to DLIMITEDSCAN (01 02 01 2 S cw 0 ccw castvalve.
FROM L. N/A to L N/A INCHES FROM WO CL to Beyond ANGLE: 00 0 45 0@ 60 other 60RL FROM 0 DEGto 360 DEG
' NO SCAN SURFACE BEAM DIRECTION QLIMITEDSCANC I 0 2 0 1 [ 2 C cw 0 ccw FROM L
- _to L INCHES FROM WO to ...
ANGLE: 00 045 060 other FROM _ DEG to - DEG 13 NO SCAN SURFACE BEAM DIRECTION UMITED I SCAN 0 :102 ( 1 [1 2 Cw [cw FROM L to L INCHES FROM WO to ANGLE: 0.00 45 0o60 other FROM DEG to DEG
__ ________________________ I ___
j NO SCAN SURFACE BEAM DIRECTION 0 LIMITED SCAN 010 2 [ 1 El 2 Cw Ccew UT-1 2-981 FROM L to L INCHES FROM WO to Sketch(s) attached 4
ANGE:00 50 pn o~er - FROM DEG to DG Z yes [ No Prepaed BY. David j
ATTACHNENT I4 PABE'?? 804G'
Supplelm Report Report No.: t I61 Page: S of 7 Summary No.: .3.89m.0129 Exminr: GWeOW. David M. 'Leveloys: 1141 Reviewer: Date:K7.
Examner. Halglr T Level:U. Site Review:
Othe" l LA r "Level: NWA ANDi Review: Date:
- .Comments:"
P/P16- Vol-vle Skeich or Photo:
-S2-ATTACHNENI -1 PAIE ~D?
Supple m Report Report No.:
Page: 6 of 7 Summary Noi: 03.89.11.012 Examlner GrIebel. Davt A Level: i-N Revewea, AJ~ c4in~e,#~~ Date:
f Level: f1-N Site Review: Date:
Examiner Hagleir, Tarry, Othet WiA Level: NIA ANII Review.
l C~ommenfts Thicknes &Profile
-VWY25 Sketch or Photo:
~ -
= *
. -- T NZ~ t~
ATTACUHEE!I i
rIE??F9 ME*
o
Determination of Percent Cove rage for UT Examinations - Pipt Site/Unit Oconee I 3 Procedure: PDI-UT-2 Outage No.:
Summary No.: 03.139.11.0129 Procedure Rev.: Ef Report No.: UT-12401 Worksoope: IsI Work Order No.: 0195838: Page: 7 of 7 45dea Scan I 100.000 %Length X 0.000 %volume of length II O= 0.000 % total forscan I Scan 2 100.000 % Length X 50.000 " volume of length /I DO 50.000 % total for Scan 2 Scan 3 100.000 % Length X 50.000 % volume of length 1I )O= 50.000 % total for Scan 3 Scan 4 100.000 % LengthX 50.000 %volume of length/ I DOa 50.000 % total for Scan 4 Add totals and divide by 0 scans 37.500 % total for4S deg Other deo - (to be used for supplemental scans)
The data to be listed below Is for coverage that was not obtained with the 45 dog s Scan 1 " Length X_ %volume of length I 100 M %total for Scan I Scan 2 " Length X % volume of length I iO0 - %total forScan 2 Scan 3 %Length X % vokume oflengt i 100= _% total for Scan3 Scan 4 % Length X % volume of length I 100.ox% total for Scan 4 Percent cornigeto covemsa Add totals for each scan required and divide by # of scans to determine; 37.500 %Total for complete exam SIte Field Supetvlsor. ~i2 ,i11. - Dat r 4 a . ! * .. .
I.
UT Calibratio I na sAllount Ocoeeg I.. . 3 *NDI-610 Outao No- '_ -_
Sumnmary No.: 03M.C13002 Procedure Rev.: Report No-- UT-1.246 is' Work Order No.: Po*o: I of Code: 1....ooA ComJim: CA IC.3 'Lo _
ang No.: .... o~o-201.8-00.1 oesctonc Tubeah, t to SheU System 0D: 03 Cop qet;D 3,SGA.WU 6welliellgh: MIA Thaanesi~smeter. C31I29M2INA fvata lonh Yes -Se attached sheOt tot Tmo; 11O Finsh Time: 1410 Ins.iva.." Seotin ." Seao, unut l ., "D3 ia OUnied Search Unk S a! o.: .- .. OOW HDIC Seril No.: F2.8M. Checks -.
XRAUTXRAMER Collu,,kxn Swnh SweeCp Sound Patn
_____________ Ko - Relect. Amp*Itwde % Dedan Model USH4, Sime: 0.75 Shape S.,,d "lr11in so 1.0 1.07 Dda~.
1.26 igo 1.0 Fmq.:. 2.25 M~z Sw~e: Ganuna .!! 2565 2A4 2A3 A",,! C4~ 9311 .. P"*.er k h E=m Ang*e: 0 Sao Et , ",, ,1,v.Cl. 1 318 35 36S 3A.
ReJo 0% s - -K Lo. Final Cal 1 530 WI I Rep. Rate: A,1Kohgh feq.: 2R5 MHZ* Moesured Angle: 0 CLuplmut o:lt,:
. . Fied Fxed Otow,. __t___
U...Pwaw Interal call Type:
121w ULTRAG*RI. II Clr-urnfen"l
=on SW" OrientatedS""Search Unit V
A.Gain (do- :36A Cite. Gain (S)X WA search Unit Ci"o Mfg.: SONOTgeC Refleclor Aptds % oMalon -
I Screen Div. 11.0 In.of Sound Path Type: RO . 174 Exam Batch 12125 NA unety ReWP ..: ... Lft w W.Cann-* o Type: ULTRAG. .-.-
C m: ~Scan Coverage Mfg.: SONOTECH '_ _
-Ca. Blackb T.",lc"kn
,"",m,,5.0:O
.... 01"44o
- ':aIS.: ... _______ _
Upaliii 6a Downstream OWN ] . (COW -
Scan dB: 434 Soan dB: NIA *Gata Peencei*Io~i O.: J ReIuitlek Sco17 Pu0
- Cal.SIlk TeMp. .-73 Temp. Took: MCD--131 x.am Surface: O.9. Sei p45°n
- .. Temp. .74: Temp. Took MCNDM401. Swim.Conotdon: As.rd T -ne , P .:,0 Recordable Indlcation(s):* Yee No (if Yes. Ref. Afttahed Ultrasonic Indkcaton Report) ___
.Reoulta. Accept.r . Reject lwJe 0*Q*Cr-t BacIeln lost at 2. fro* weld tooedue to tubedot.
iPecen Of CPeameOtie 0: N Reviewed Prev~ous Data: yes WA Ransom. reg ..
Examiner:,-.. e IA.: Sonature Dole SU Di
- ' .. C,--.
....... :/2 Other Leve U" WA natureDo atrDb ATTACIKNENI 4.
II FABE'~( OF%~
UT CaIlbratIo Iriation Coon.. 1 Outage No. & M_
Summaay No.. oa~cis&om NeowdM Rov. * .7 Repet No.: UT-41417 Wadcaoope: lit Work Oero No.: Pass: 1 K.
CaL~em: .A ,ct.so .1oallon Daciltn Tubestet to Shel System ID: o3 Component !D: 34, .W ,, iselfeangth: MIA Thloluesa~lemeter. iSI &12rI NIA lbiim. ions: Yes - Seeaattached sheets StanyTme: 1150 M~rall ie 1410
___________ I -.
instrume.nt Sett.ngs Search Unit Cal. TIi. . Date Axh' Ortenteted Search Unit Seral o.:23P0 Sedla No.: 1.2910 Checks I . Calbaution Sgns.- SWOOP ISound Pamh Manybutstsre GE Manufacturer. KBA Inia cOl l.OM' 7M1201 Reflector Amplhide 7* DMIviio Mod " USH. so w Sim: X.01.0 Shape: Ra," 1 nter. C aL ___ 0_
_ M1 so 1.1 1.3..
. .737.
La. Range: 1,-s Freq.: 2.25 MHz Style: C, Ma I nter..Cal. 1 *I I _________ 2.6 1.1W M^ CaWel: .1270 Pulser. Square Exam Angle: 35 8 it B Smento aY50 &9 C wIFe.Ce tl._ ,n_+,
DamplW 5004 Reject 0% Moea:
to Notch 100* U. L6.25 Rep. Rate: Auolg Freq.: 2.25 MHz Meassursd AngWe: 3? *514T 4., 6.4 7.60".
Flfter Fixed Mode:"' P Wedge awtye: SW . Cal Sauch: .121"U SIlrcumfrentlal Orintatd Search UnIt Volt*a.: .450 Other. Fu.wave, Type: ULTRA2ELn'f Cuilbrmllon Signal.- Sweep Ax Ganin* do 30.0 CIMo Gain (45:o 30.0 Search Unit Cable Mfig. GONOT9CH: Reflecor Ampilbde Divison SudPath S ari - 1.2 in.of Sound Path Type: RG -174 WA Exm Batch 12CIS IhisWiy Report No.: 1.12-10 Lwnufw v... ft. Cams.: 0 Type: . ULTRA*tL I Sean Coverage . MUg.: SO-bTiE.
C4 SlOck No. 2oT.240 Up*eam Downstrvewa ScaB:.44.0 Re,*erncelm mulator lock Thlkns . ~ . 'a CWG5 CCWfi Scan dB: 44.0 Sr o: 041 GaidiR lnra-iector l,.% .+SWOOI Sound Path
.. Cal. BTemp. 73 Temp. Tool: MCNDE40131 EtmnSl O.u.e . Type: RQMIAS As Ground ,. . 19.6]r RadlueL 50 IA LOD, Comp. Temp. 74 Temp. Tool* MCNDE4OlI3 Surkae Conditlon:
- eco.dablelR IdicatIon(s). Yes Q No (If Yes. Ref. Attached Ultrasonic Indhcatn Report)
Result:* Accept Q Reject
- Info 0 Comments: Cafbratlon raefectors Virtifid uing dynamic scan. 3..
so.o Percent ..Of Covge lObtained 00%: No Rehlqed Prvous 0te . Yes Examiner Lewe /gn0Oae 04i Reviewe sw.ab" Dat Oats Level NA DIm flat NIA Ele~vew / * ~ J *~IO nAh 4 --
NIeA Leve wA ww-W Dale ~pCow Dals
. e, .0. #./-
HIA -d~
I
.t~7 ~ -~ .. ., - .P.k~
~-
AT TACOHEN TA-0 II 'PAIE 0 4
UT .Calibratloe mnt q SamýiyN.
Oco '1.. .I
- ND420 Outage N" OLCI.30.0002 PWrcekOr Rer-. 7 Report No. W21
'Work Ordeir No.:.
liS *~3648 Pagp: __ofM__C11 11991120HA Ca.*lhm: C-A CI.25 domUos II 0M401.S-0001 m n , ktp c Tubahhet to Shill System. 10: 03 Component 0*: S.SG-W69 NIA t~~mltat 76.76 YsSeal sheets SWtTirs: 1153 Finlsah Time: 1410
- luabumen~ft Settngs Search Unitkl Axia Orientateol Search Unit Seial N.: No.. Serial Not: C
..U:arufteboec 1CZJTKCAjER. Mauacue KRA Initial Cal 0931; 5171=20 CaI b n Signal Sweep Pat Reflector Amplitude % Divulop ud a Moc UNOStv. 1*1 Shape: 'Round inter. CaL__ I15 70 T 1.2 18.4" De: fer. 1..'w Ra ge:;
e Sane Gamm Inter. CaL 1113 ; r 25oe9 2A 3.75 Md C.nVe: 1274 PUlsa. Hig05 Ao,- Inte -
. ampng. .. 1K Reject 0%. Mode: shear. .n Cal 1542 Wr712 ID -oc lp 10in 4.8 7.45 Rtep. Rate: Antohgh Fr...: 2.25 Ha Meaud Ane 47 couple fit .aon 40 Uo LW Flitec wie Mode: P Wedge SWye *. owi Cal. uatdr, .1212 Clrcumferenftas Orientated Search Unit Votg: fied Other Pullmav Type: ULTRGE'LD Ax. Ga:in(dD) 44.2 Ckc. Gain (d.) 44.2 Search unit Cabl" Mfg. SONbiEC.
I reasowY*3 1.5 in of Sound Patlh Tpe RG - 174 mfati 125 efctr AmplitDeI % Division SoundPat S :n..L.... y Report No.:; L-l Lg, VLo NO. CoWL 0 Type: ULTRAGME U Signal Sweep, Block 0.lbato soen coverage Mfg-. SONTUiR Ca.BokNo. .20T.2A0 Upstreami Dowvsneeamfo ScandB: SU Thilckness ..$A Diaz. Fla CW0 cow0 SqefldB. -u 6617-
!ellN. Gain Signal &APSw S Path ElamO SS" .D. Tpe : :j!L RialMNo dB Reflector Ampltd %1 Divelet Cal. 9IL Tem p.: emp.. To k.
T .73 NDE40131
.*...C r fItediusI so 0 IA I 2.gr
.C"mp.Tep". 74 Te"p. Toolk MCHE.i'.:' Surface C*d.il. As Ground Recorda"bIueldlo*aion(s): Yes
- No ' (ifYes, R*f. Attached Ultrasonicla lnloIM Report.)
Re.: t::.. Accept : Reject Ea Info I Comments: CaWlbraton refneto Verified v u*ng dynamic san.
Percent Of
.Coverage Obtaine *,. 90%:
No: Reviwed Previous Data: ..Yes
- -i., , Revee ale
_ .- Lev
- i:i!i?:i Halger~ ony 575212 Examinrbr Level WZA d Sie'a other. Leel A SDgnbuaw Date Date NIA v
- i-.iU ATTACUKEUT 19 MAE 9-3 Ff /,
UTCalibrtionI~rinaflon U::.
-... UDEm Outage No. - $
Suminay No.: _ _ 03.& ~1iOM02Procedure Rev-* 7 RepmtNo.. UT4248S?
leiWodcOrder No-: oigmt Pap: 3 0,
-od.c~ 190810M Cat.uim: CA 161.3011 Orwing No., 0I.21.-0001
Description:
tubiaee to SheD System ID:. 03 pntID: 3.rA.WO r .. .I Skefu " WA Thicineagl* ama I.N"A.
- ,--n: Yes See, Wad - ,-'f .SW Tk,. 1155 Fish Time 1410 Insirnient Settings Search1 Unit ~
Serial No.: TJXT SOW No.; OLL CheckT*
Mah~bwwf.ue K0UTCRAMER manufacimin: iCBA milal cal 0ae.517U1212 Rfeo Smpigna e Swee" U
- Model:.. USNI
________________SIM:_____ 1.0 -h. -on . we__ .
so____ 1.3 -.
2.8?
- i:sy: s 17.=420 Range: " .0 FrTq.: 2.24MHz Style: Gonua Inter. Cal.5 2 so - -
_V___eN.:
A26-l- .... ExmAngl: so#Ofl .3 -w. 6Z.. . -a. a m*n S m 0 4.
W 7O SWPAMh Sound
_______ Rata_____ .5Mz Wu~lFe-Age Maued le: IWS Cal. I 20j. 41A____ WoL
- 11. Scareen Di.12-067 f Pula.tih Son TypAnge:
__O___
SO -of1lma4 a -
Type:' asw 358 See___ _____
R.1ep.Repert No.:: -2.250 MHZ of V No
________ a. CUpLmaant _______
DaExnm*aK .e-. 1,
..... Scam Coverage MW. S0NbYrlCH
. .. ;:Cll.. R.. tNo:L120 a.licuMock:. Iigli NO.0' 1.' .tpeU T .E.. ,,II. I *.
Votage.:
.e.:
BlockNo. .
_________ d e Flat 2_T___Upstream______ 1. S .d.B Typ: ULAU_dB._US I C1aiian S Ognal SWeepd Unck ras..Gain B 48.6 C Gain d 4w8,.5..g..~.. al M.. . d.B R lec Apiid,, % Division SCreL kTemp.n 7 Temp.0To MCIrI 0Son ExatSh Type ,O , UTyp, 1, S Aod"-
A..,
L
.. s1.. Tap 73*m.To CU4OS mSrae Type: ROW.AS 42.0 r Radius so 1.0 &W c*mp. Trep. 74 Temp. Toot MCNOE4O13, Sure Condition: As Ground Re'ordable Indication(s)= Yes Q-' No*1 (IfYea. Ret. Aflached Ultrasoidc lndi*al.n Rape.*)
Resuft AccW C] Reject [Z InIoQ Cotmnits: Callbrallon nefloctora verkied "sin dynamic seam.
.Pertcent Of Coverage Obtained >80%: No Reviewed Previous Data: Yes Exeulrther Level. jie-PAN/r intueDt Day. oh... . 5*7.1202
[Examiner Lve WA SignatuviewDae IWA NSA',:
,ter v WA Signature Data I CEI 1-,49 PA 0
UT Calibrati . Ilation ocanes I NbSd2 0gepmw 03I.0..0002 Procedure Rev.: I is' Work OrderNo.: 01956846 Page: 4 of- -4,(15 catftamn: C-A C1.30 La~Uoe:
1.201.8-4001 Dascrlptlo ubeaheto Shell System :ID: 03
- ompon-nt 10: +-- GA-W ShtasA~noh- WA ThllheasD~mesn 0 125*1WAIN Li o: -"Se attached Staanybme:. 1315 Fbsh Time: .1410
- ________ U ~-.
Search Unit. - I III II I I I CaL I Time Daft AxkW Odkaktotd Searc Unit Scula No.: 00TJixT Seal No-, 07M1L, check -.- Calibrallon signa Sweew Mmufacue,-~ KRAUTKRAMER Mantugwollge KSA kn"a Cod, 085W=712 OU Relotor Ampid % DImon aime 1.0 show. Rouand Itr a AO t__-_lo 1.8 .80 -
Fmq.: L25 M-- Sl"'lemun..
ItrCa.13154 V=702 I * '__o-c:Ll _In.
56 4.2 P2.Ir*
I K".CaI~et .12167 Pwsew Wgi Exam Anqle s ot00flernmnt: Singl ! _______ 40 6GA 3.14*
Dampln 1K Reieol 0% Mode: mew I 1555 iro¶20121 I-tail, 114?rSON 48 5.1 2A8r Rep. Rata Autohh -Preq. 2.25 MliX measured Agte 6
- Cupism
- . Y.
... Filtr Aixed MMe: Circumfuowl" Orienltatd Search Unit F Wedge Stli SINS COL Safti IM25 V~lae -Fixed Other. Fullmeee Caibraflon ftrud &we"P onPa Ax. Gain (dII): 4U. Cia Galn(,)c 46.0 Seach Unit Cal" Mfg...: SON Re1e,.,r AMplit %
i ,,, ,Ison. .
I Sren~v~ ':J~o Soflnd Pat Type: RG - 174. Exrn . 12, Linealy Rqport No.w:20 L .f.. Nv fotCo,.: 0 Type: UL1O.*L U Scan Coverage , mwg,: SONo'mc Ca~bratf on Block Of Soc*t No.1. 2OT.40. Ups&*a=n Downem O , Z Scan d: 620 S -ree ,Refegece/Skoulatr
. I uI 81ocA o'
Reference Bback 50
&hcnes DID.: Flat OW COW Sam do. 62. GaI I Sig-
- Ca. 8kem p. +, 73 Tem Tool CD4O3
, .Ewen Swk,,,
s ,,o.D.. - reulal No.: .08.1451 dB Reffectior Arple%I DMIel '" SoI
___.s_Pam ryPe . ,
....T Cp.Temfp. 74 Temp Tool MCDdIA ¶ :.Srae odo: sGon Recf .l. Ac Ye Ref. aca IRdiajeotRepInt.)
Reut: .Rjc
- if Acp Comments: Cealtion efectoes Vrelied using dynaic s=am. 14T.
SOD to OAX. 44.o dI.
ParcantOf Coverm~ Obtained ; 0%: No . . ewe Previou Data: Yes C.AD~Jon Nao reiu &
!nuAe Oeaes SORvewMop NIAA
'D~e as1
- e oftbU NIA I&Z ATTACHNENT 4 PAGE gOF '?*
DUKE POWER COMPANY ISl LIMITATION REPORT Component/Weld ID: 3-SGA-W69 Item No: 03.C1.30.0002 remarks:
0 NO SCAN SURFACE BEAM DIRECTION Lateral Restraint #1 E- LIMITED SCAN [ 1 0 2 0@ 1: 0 . 2 cw C3 cow FROM L 2-12.5" to L 2+12.5" INCHES FROM WO, CL+3.0".. to Beybnd ANGLE: 000. 45 . 60 other 6ONS FROM N/A DEG to N/A, DEG 0 NO SCAN SURFACE BEAM DIRECTION Lateral RestraInt #1
- E LIMITED SCAN ED 1 0 2 [1 1. 0- 2..K cw 0 *ccw FROM L 2-12.5" to L 2+12.5" INCHES FROM WO. CL+2.0" to CL-2.O" ANGLE: 00@ 45 0 60 other 6ONS FROM" N/A DEGdto N/A DEG 0 NO SCAN SURFACE BEAM DIRECTION -Lateral Restraint #2 E- LIMITED SCAN 0 1 02 09 1.' 'S 2 .l cw 0 ccw FROM L 9-12.5" to L 9+12.5" INCHES FROM WO CL+3.0" to Beyond
.ANGLE: 0 00 45 0 60 other 6ONS FROM. N/A DEG to N/A DEG 1Z. NO SCAN SURFACE BEAM DIRECTION Lateral Restraint #2 F1 LIMITED SCAN ED 1 02 01-'[l 2 Cw0ccw
- .FROM. L 9-12.5" to L 9+12.5" INCHES FROM WO "%+2.00 to CL-2.0" *Sketch(s) attached ANGLE: '000 45080 othe " 60NS FROM- N/A DEG to N/LA,_ DEG I yes E' No Sheet 5 of 1i.
. 7- OWt ATIACPHMENT 6ý-.
0 0 MAE Y0f
Oe B 1~
DUKE POWER COMANY ISI LIMITATION REPORT omtonentfWeldID: 3--SGAW69 Item No: O3.e1.30.0002 remarks:
s NO SCAN SURFACE '.BEAM DIRECTION Lateal Res"taint #3; LIMITED SCAN I0 ( 2 Z- 2 cw@3cw cw __
FROM. L16-12.5' toL 16+12.5- INCHES FROM WO CL+3.0_ to BCynd..
ANGLE: 000 45 060 other 6ONS FROM N/A DEG to N/A DEG
- 0. NO SCAN SURFACE BEAM DIRECTION Lateral Restralit #3
[] LIMITED SCAN 0 1 0. 2 3 t 0* 2 j@ cw 0 ccww FROM 16 4-12.5" toL 16+12.5' INCHES FROM WC: CL+2.0" to CL-2.0" ANGLE: 00 I045 .060 other 6ONS FROM N/A DEG to N/A DEG 0 NO SCAN SURFACE BEAM DIRECTION Lateral Restraint #4:
[]LIMITED SCAN ;1 02 [Z I. ED 2 0 aw 3 ccw FROM L 24-12.5" to L 24+12.5" INCHES FROM WO: CL+3.0" to Bey0ad ANGLE: 00
ý130 45 060 other 60NS FROM., WA DEGto N/A DEG .
- 1 NO SCAN SURFACE BEAM DIRECTION Laterai Restraint #4: -
I::E]LIMITED.SCAN 1 I Z] 2 El ! F.[3 2.0 aw 0WI. =cw FROML' .24-12.5" to L 24+12.5" INCHES FROM WO _CL+2.0"' to CL-2.0" .Sketch(s)attached
- ANLE*I :.!'0.0.0 45 [] 60 other 60NS FRO.M:-. N/A DEG to NIA'. DEG 0* yes " -13 No
- Prepared: Gregory Ra!!som *al: '" Date. 05/07112 Sheet. 6 of 15 "dam Re.iewed .Authoiec B:A
.. z Date: /,;_***'
64,;7L."* :*
spect6r: -. Date: el* Z' ATTAUNHENT~
DUKE POWER COMPANY ISI LIMITATION REPORT Component/Weld ID: 3-SGA-W69 Item No: 03.CI.30.0002 remarks:
0NO SCAN SURFACE BEAM4 DIRECTION Latera Restrint #5 I LIMITED SCAN 0,1 02 10 .2 [1cw[ ccw FROM L 31-12.5m to L 31+12.5" INCHES FROM WO. CL+3.0". to .Bend ANGLE: 00.0 45 060 other 6ONS FROM N/A DEGto N/A DEG 0 NO SCAN SURFACE BEAM DIRECTION Lateral Restraint #5
.E] LIMITED SCAN 0,1 02 - 10 2 Scw*0 CCW FROM L 31-12.5" toL 31+12.5" INCHES FROMWO" -L+2.0 to CL-2.0" ANGLE: 000 45 10 60 other 60NS FROM N/A DEG to N/A DEG 0 NO SCAN SURFACE BEAM DIRECTION Lifting trunnion QLIMITED SCAN "I1 02 01 EJ20cw lccW FROM L 1-9" to L 1+9" INCHES FROM WO" CL+7.0 Jto Beyond _
ANGLE: 0 00 45 060 other N/A FROM N/A DEGto N/A DEG 0 NO SCAN SURFACE BEAM DIRECT.ON Lifting trunnion l LIMITED SCAN 0I-1 0 2 0 1.. E]"-"2 El cw I:.ccw ..
FROM L 12-9" to L 12+9" INCHES FROM WO' CL+7.0" to Beyond Sketch(s) attached ANGLE: [J0Q 45 0 60 other N/A FROM N/A DEGto N/A. DEG 10 yes ' No Prepaed B. Gregory Ransom , ,V4 .v.I. .Date: 05/07/12 Sheet 7 of 15
°..
Reviewed By. Date, Authorized Inspectdr~
, _ 00t.:
-:
- I-N OZ. Z
- -ATTACHNMENTI
.PA6Ef'f.F' 4 .
- 1:.
As 0,
DUKE POWER C6W~ANY ISI LIMITATION REPORT ComponentWeld ID: 3-SGA-W69. Item No: :03.C130.0002 remarks:
- 0NO.SCAN SURFACE @EAM DIRECTION. Marway ILIMITEDSCAN 0i 2 Z- 1. [3 2 3 cw E .ccw SF'ROMlL7-10" .to L 7+10" INCHES FROM WD CL"7"" to Beyond ANGE: *0*45 *060 other FROM NIA DEG to N/A DEG ElNO SCAN SURFACE BEAM DIRECTION 0 .LIMITIED SCAN .IIE 02
] 51[JEl2[0Jcw Elccw ._ _ _ _ _
FROM L to L INCHES FROM WO "_ ._ to " '_ __.,.
.ANGLE: .[10 045 0-60 other FROM. DEGto DEG El: NO SCAN SURFACE BiEAM DIRECTION 0 LIMITEDSCAN E01 [ 2 EI" t. 0 2 0c .. w __ __ __
FROM. L toL INCHES FROM WO to ANGLE: 0 0 0-45 0 ,60 other FROM. DEG to "___DEG i0E NO SCAN SURFACE 6EAM DIRECTION
. LIMITED SCAN El [1r2 [" 2[1l cw C ccw FROM L to L INCHES FROM W0 to - Sketch(s) attached 4
ANGLE.: -0 5:D 060 other: FROM, DEG to. DEG 0 yes " No eeae..Ge"oryRansomn 0507/12 Sheet. 8 of 15
- ~le ... )7r=*:* .1/1 ZA,& Z .'-n:I Authorized ez*, InspecftcV.. .I re
.Date: =-
Reviewed, By ae:
ATTACHNENT1 4 PAM[O OFft-0
Steam.. Generator Upu* besee Sel This scan limitation exist for 125" of weld lewth Weld No. ; 3-SGA-W69 Total Scan Coveage fOr 00 CW & (CCW Iten No. :.03.C1.30.0002" Scale 1"=2" e t OOdW&CoM I
I...
I.
Base MdI ýe .34 sq. in.
S Weld Mea A .ea=636 sq. in.
Total
,Are-=15.7sq. in.
Stwa 1-. .besheet Surfce 2 - Shell
- 00. C.W& CCW Coveiage - .- Y 1.7.sq..... x 12S"-19625 sq. in. 'I 15..7 sq.....
- 465.. 73005..sq.uL a.
1962.5 sq.in.- 7300.5 sq, in..= 5338 sq.in.
(53 38 sq ini -7300.5 sq~In.)100=73.% of Weld e94:e Page-I-Of- ATTACOHEII.W 0 pA6 Eb F Pd
Steam Generator Um&-rubeshet o Shell 4p This scan limitation exists for 125" -ofweld 1IM Weld No..: 3.SGA-W69 Total Scan Covdagp for Near Surface ItemNo. : 03.C1.30.0002.
Scale I" = 21
[at=]a Riswin T 60P Surfce I - Tubesheet Surfam 2- Sll
".!"a S:3.71 ;sq.
in.mtotal Near surface volume 311* s. in. x465"= 1725.15 sq. in.
3071 sq.in. x 125"= 463.75 sq. in.
463 W...75,sq. ýin- 1725.15 sq. in--1261.4 sq. in.
1261.4/1725.15 x: 100= 73.1 %
Itspector//Date:
M fF
.Steam Generator Uppdrubesheet to Shell Ibis scan limitation exists fbr 125" of weld lenge.. Weld No. :3-SGA-W69 Total Scan Coverage for Weld Metal Item No.: 03.C030.0002 Scale I"= 2" LateralRe
. . i. ii
.:..Base Area 7T84 sq. in WeldMetal Area 4.17 sq. in.
Total Exam Area 12.01 sq. in.
Surface 1- Tubesheet Surface 2 - Shell 5 .
- 0 .....
- VM d Metal Covemge Wed..Metal Total Area..4.17 sq. i x 465".1939.05 sq. i*.
S* Metal Total Area Not Sca*med=3.48 sq in. x 12 I..
,435 sq.dvi - 1939.05s.n.x154.
T sq. i. -q9.05 (1::i0504.05 sq.inJl939.05 sq.m.)100 77.6%of W#ve hispector/Date:
Page I Of IACNHEM I A'
- , .V MAE & OF4~
0 :Steam Generator.ppi re..... .... o Shell .p This scan limitation exists. for 125" of weld length Weld No.: 3-SGA-W69 Total Scan Coverage f6r Weld Metal with 600 Item No." 03.CI.30.0002 2" "
Scale 1 Lateral ResOW Base NMkal Area = 7.84 sq. in.
- Weldl* .Area-=4.17sq. in.
Total ExamArea= 12.01 sq. in 4-Surface 1- Tue Surface 2- Shell V.i 1d:Mta Coverage w/600 4..*,17 sq.. x 465"= 1939.05 sq.i 1..65 sq. in.weld metal not scanned x 125"=- 206.25 sq. iL 206.25,sq.in. -1939.05.sq.in.= 1732.8 sq.insobtained I..
I73-28 sq.inJ 1939.05:sq.in.)100- 89.4 %of vWd eli In'spector IDate: 2 PA e-
/t ofjý AITACH NE NT t9
]~ PA6EY3' OFY6.
0; .Steam Generator Upp~rubesheet ito Shell Tiis scan limitation exists for 125" of weld lenmgh Wed No.: 3-SGQ-W69' Total Scan Coverage for Base Metal Item No.: 03.C1.30.0002 Scale 1" = 2"
- LateralResU~nt
-. p
.. ~ 4 f..a . .. **.. .;~*..*-
Base Metal Are -7.84 sq. i.
Weld MNetalArea =4.17 sq. in.
Total ExaArea= 12.01 sq. in Surface 1 - Tubesheet Surface 2- Shell Base Mel CDvU-a 7..4 sq.irn x 465=-3645.6 sq.in.
.5.18 sq. ih bsemetal not scaied x 2**= 647.5 sq. in.
647.5 sq.in. 3645.6 sq.in.= 2998.1 sq.in*obaned
.(2998.11 sq.inl 3645.6 sq.in.)10( 8.2 %of BM I.
Vr~ector/Date t3 e~jofjýATTACHNENT A S. PA6Ey'OFf6;
Steam Generator UArýueseto Shell a,'
This scan limitation exits for 125"of weld leieh WeldNo.:: 3-SGA-W69 Total Scan Coverag. fOr Base.Metal with 600 Item No. : 03.C0.30.0002' Scale P = 2" La1er4R~strunt~
p BaseMea lArea*=784 sq. in.
We-d Metal Area 4.17 sq. in.
Totai l E ii4o ea.= 12.01 s% in Suri I1-Tubesheet Surface 2- Shell BaeM etal Coympa w/60P 7.4 sq.i.
" k..4".3645.6 s.in.
1.81sq"... oscanned x 125"= 226.25 sq. in. r I.
226.25 sq~n 3645.6 sq An.= 3419.35 sq in~obitained (3.419.3.5 s7.inl 3645.6 s*n-i)1-393.8 % ofiBM lbspector /Date:
Pgg'r f 4ýA 7A ER E'T
0 Steam Generator Shell to Tubesheet Umitations Item No. 03.C1.30.0002 / Weld No. 3-SGA-W69
-~LU Total 00 Scan eraSe 73.1% .
Near Surface Coveraep Scan Angles % Coverage Obtained S1 600 73.1 S2 60 73.1 C-W 60' ... 73.1" CWW 60W 73.1 Total Near Surface Aggregate Coverage = 292.4/4 73.1%
Weld Coverage Scan Angles % Coverage Obtained 51 45, 6Q' . ".73.1.
S2 450, 60 (77.6 +894)2=83.5 CW 350, 45*,* 60* 73.1" 0 ."" Cww -450, .6 73.1 Total Weld Aggregate Coverage = 302.8/4 = 75.7%
Base Metal coverage Scan Angles % Coverage Obtained S & S2 350, 450, 600 73.1 CW & CCW 450, 60° (82.2 + 93.8)/2 = 88.0 Total Base Metal Aggregate Coverage = 161.1/2 = 80.6 %
Total Aogremate Coveraae= 73.1% + 73.1% =75.7% + 80.6 a 302.5/4 = 7:.%
Inspector/ Date . S/" -7 / V- Paso-L-4zoff .
PaeA