ML17333B066: Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(Created page by program invented by StriderTol)
Line 17: Line 17:


=Text=
=Text=
{{#Wiki_filter:DONALD C.COOK NUCLEAR PLANT UNIT 2 CYCLE 11 CORE OPERATING LIMITS REPORT (COLR)Revision 5 September 1997 97i0080032 970930 PDR ADOCK 05000316 R PDR COLR for DONALD C.COOK NUCLEAR PLANT UNIT 2 CYCLE 11-SEPTEMBER 1997 1.0 CORE OPERATING LIMITS REPORT This Core Operating Limits Report for Donald C.Cook Nuclear Plant Unit 2 Cycle 11 has been prepared in accordance with the requirements of Technical Specification 6.9.1.9.The Technical Specifications affected by this report are listed below: 3/4.1.1.4 3/4.1.3.1 3/4.1.3.4 3/4.1.3.5 3/4.1.3.6 3/4.2.1 3/4.2.2 3/4.2.3 3/4.2.6 Moderator Temperature Coefficient Movable Control Assemblies Group Height Rod Drop Time Shutdown Rod Insertion Limits Control Rod Insertion Limits Axial Flux Difference
{{#Wiki_filter:DONALD C. COOK NUCLEAR PLANT UNIT 2 CYCLE 11 CORE OPERATING LIMITSREPORT (COLR)
-(AFD)Heat Flux Hot Channel Factor-Fz(Z)Nuclear Enthalpy Hot Channel Factor-F"<<Allowable Power Level-(APL)Page 1 of 11 Revision 5 l l COLR for DONALD C.COOK NUCLEAR PLANT UNIT 2 CYCLE 11-SEPTEMBER 1997 The cycle-specific parameter limits for the specifications listed in Section 1.0 are presented in the following subsections.
Revision 5 September 1997 97i0080032 970930 PDR R
These limits have been developed using the NRC-approved methodologies specified in Technical Specification 6.9.1.9.2.1 Moderator Tem erature Coefficient (Specification 3/4.1.1.4) 2.1.1 The Moderator Temperature Coefficient (MTC)limits are: The BOL/ARO-MTC shall be less positive than the value given in Figure l.The EOL/ARO/RTP-MTC shall be less negative than-5.00E-4 b,k/k/'F.This limit is based on a Tavg program witll HFP vessel Tavg of 574 F where: ARO stands for All Rods Out BOL stands for Beginning of Cycle Life EOL stands for End of Cycle Life HFP stands for Hot Full Thermal Power RTP stands for Rated Thermal Power 2.1.2 The MTC Surveillance limit is: The 300 ppm/ARO/RTP-MTC should be less negative than or equal to-4.15E-4 hk/k/'F at a vessel Tavg of 574'F.Page 2 of 11 Revision 5 A COLR for DONALD C.COOK NUCLEAR PLANT UNIT 2 CYCLE 11-SEPTEMBER 1997 FIGURE 2 ROD BANK INSERTION LIMITS VERSUS THERMAL POWER FOUR-LOOP OPERATION 250 225 I-'(54.5, 231)103 STEP OVERLAP'200 I (10 0~189)z 0 i 175'I 150 I (BANK C)(0, 128)0 100 4 1 0 75'(BANK D)I, 50 25 0 9 I.,', (090)'l.!t I Q%IQ%2Q%3Q%4Q%5Q%6Q%7Q%S0%9Q%IPQ%RELATIVE POWER Page S of 11 Revision 5}}
ADOCK 05000316 PDR
 
COLR for DONALD C. COOK NUCLEAR PLANT UNIT 2 CYCLE 11 - SEPTEMBER 1997 1.0     CORE OPERATING LIMITS REPORT This Core Operating Limits Report for Donald C. Cook Nuclear Plant Unit 2 Cycle 11 has been prepared in accordance with the requirements of Technical Specification 6.9.1.9.
The Technical Specifications affected by this report are listed below:
3/4.1.1.4       Moderator Temperature Coefficient 3/4.1.3.1       Movable Control Assemblies Group Height 3/4.1.3.4       Rod Drop Time 3/4.1.3.5       Shutdown Rod Insertion Limits 3/4.1.3.6       Control Rod Insertion Limits 3/4.2.1         Axial Flux Difference (AFD) 3/4.2.2         Heat Flux Hot Channel Factor- Fz(Z) 3/4.2.3          Nuclear Enthalpy Hot Channel Factor F" <<
3/4.2.6          Allowable Power Level (APL)
Page 1 of 11 Revision 5
 
l COLR for DONALD C. COOK NUCLEARPLANT UNIT 2 CYCLE 11 - SEPTEMBER 1997 l
The cycle-specific parameter limits for the specifications listed in Section 1.0 are presented in the following subsections. These limits have been developed using the NRC-approved methodologies specified in Technical Specification 6.9.1.9.
2.1     Moderator Tem erature Coefficient (Specification 3/4.1.1.4) 2.1.1 The Moderator Temperature Coefficient (MTC) limits are:
The BOL/ARO-MTCshall be less positive than the value given in Figure         l.
The EOL/ARO/RTP-MTC shall be less negative than -5.00E-4 b,k/k/'F.
This limit is based on a Tavg program witllHFP vessel Tavg       of 574 F where: ARO stands for All Rods Out BOL stands for Beginning of Cycle Life EOL stands for End   of Cycle Life HFP stands for Hot Full Thermal Power RTP stands for Rated Thermal Power 2.1.2 The MTC Surveillance limit is:
The 300 ppm/ARO/RTP-MTC should be less negative than or equal to -4.15E-4 hk/k/'F at a vessel Tavg of 574'F.
Page 2 of 11 Revision 5
 
A COLR for DONALD C. COOK NUCLEAR PLANT UNIT 2 CYCLE 11 - SEPTEMBER 1997 FIGURE 2 ROD BANKINSERTION LIMITSVERSUS THERMALPOWER FOUR-LOOP OPERATION 250 I
                                                    -'(54.5, 231) 103 STEP OVERLAP     '
225 200 (10 0~189)
I I
175 z               'I         (BANKC) 0 i
150 (0, 128) 0 100 4                     1 0
                                          '(BANKD)         I, 75 l
9 50
                                                                .! t I                        I 25
                            '
              ., ',   (090) 0 Q%   IQ%         2Q% 3Q% 4Q%     5Q%       6Q%     7Q%     S0%     9Q%       IPQ%
RELATIVE POWER Page S of 11 Revision 5}}

Revision as of 13:05, 22 October 2019

Rev 5 to DC Cook Nuclear Plant Unit 2 Cycle 11 Colr.
ML17333B066
Person / Time
Site: Cook American Electric Power icon.png
Issue date: 09/30/1997
From:
INDIANA MICHIGAN POWER CO.
To:
Shared Package
ML17333B065 List:
References
NUDOCS 9710080032
Download: ML17333B066 (4)


Text

DONALD C. COOK NUCLEAR PLANT UNIT 2 CYCLE 11 CORE OPERATING LIMITSREPORT (COLR)

Revision 5 September 1997 97i0080032 970930 PDR R

ADOCK 05000316 PDR

COLR for DONALD C. COOK NUCLEAR PLANT UNIT 2 CYCLE 11 - SEPTEMBER 1997 1.0 CORE OPERATING LIMITS REPORT This Core Operating Limits Report for Donald C. Cook Nuclear Plant Unit 2 Cycle 11 has been prepared in accordance with the requirements of Technical Specification 6.9.1.9.

The Technical Specifications affected by this report are listed below:

3/4.1.1.4 Moderator Temperature Coefficient 3/4.1.3.1 Movable Control Assemblies Group Height 3/4.1.3.4 Rod Drop Time 3/4.1.3.5 Shutdown Rod Insertion Limits 3/4.1.3.6 Control Rod Insertion Limits 3/4.2.1 Axial Flux Difference (AFD) 3/4.2.2 Heat Flux Hot Channel Factor- Fz(Z) 3/4.2.3 Nuclear Enthalpy Hot Channel Factor F" <<

3/4.2.6 Allowable Power Level (APL)

Page 1 of 11 Revision 5

l COLR for DONALD C. COOK NUCLEARPLANT UNIT 2 CYCLE 11 - SEPTEMBER 1997 l

The cycle-specific parameter limits for the specifications listed in Section 1.0 are presented in the following subsections. These limits have been developed using the NRC-approved methodologies specified in Technical Specification 6.9.1.9.

2.1 Moderator Tem erature Coefficient (Specification 3/4.1.1.4) 2.1.1 The Moderator Temperature Coefficient (MTC) limits are:

The BOL/ARO-MTCshall be less positive than the value given in Figure l.

The EOL/ARO/RTP-MTC shall be less negative than -5.00E-4 b,k/k/'F.

This limit is based on a Tavg program witllHFP vessel Tavg of 574 F where: ARO stands for All Rods Out BOL stands for Beginning of Cycle Life EOL stands for End of Cycle Life HFP stands for Hot Full Thermal Power RTP stands for Rated Thermal Power 2.1.2 The MTC Surveillance limit is:

The 300 ppm/ARO/RTP-MTC should be less negative than or equal to -4.15E-4 hk/k/'F at a vessel Tavg of 574'F.

Page 2 of 11 Revision 5

A COLR for DONALD C. COOK NUCLEAR PLANT UNIT 2 CYCLE 11 - SEPTEMBER 1997 FIGURE 2 ROD BANKINSERTION LIMITSVERSUS THERMALPOWER FOUR-LOOP OPERATION 250 I

-'(54.5, 231) 103 STEP OVERLAP '

225 200 (10 0~189)

I I

175 z 'I (BANKC) 0 i

150 (0, 128) 0 100 4 1 0

'(BANKD) I, 75 l

9 50

.! t I I 25

'

., ', (090) 0 Q% IQ% 2Q% 3Q% 4Q% 5Q% 6Q% 7Q% S0% 9Q% IPQ%

RELATIVE POWER Page S of 11 Revision 5