ML20055C918
| ML20055C918 | |
| Person / Time | |
|---|---|
| Site: | 07105971 |
| Issue date: | 10/10/1980 |
| From: | Tenorio J, Zimmerman D GENERAL ELECTRIC CO. |
| To: | |
| Shared Package | |
| ML20055C908 | List: |
| References | |
| PROC-801010, NUDOCS 9006280390 | |
| Download: ML20055C918 (2) | |
Text
- - _.
f GENERALOJ ELECTRIC "is n
IRRADI ATION PROCESSING OPERATION RADIOACTIVE PRODUCTS AND SERVICES o
OPERATING PROCEDURE nEvisioN CASK /F N SECfl0N:
CHAPTER:
XVII.
MADUB4ANCE 0.
Nameplates i
1.
Purpose g
M g
7b define the method for the inspection and mintenance of the cask and/or fireshield nameplates.
=
8
[
'si 2.
Special Rcquirements E
a.
The nameplate will be marked with the nodel identification p{
ntrnber specified in the NRC Certificate of Compliance and other
{
information required by the NRO/IM regulations.
I i
d k
b.
The Senior Engineer-Licensing will approve all nameplate U
drawings prior to purchase or first use.
881I c.
Nameplate material shall be brass, stainless steel, or altraintn.
h cm y
4 d.
Nameplates will be attached to the cask by welding and to the y,
fireshield by welding, brazing, or mechnical fasteners, e.g.,
I rivets, screws.
w l
I s a g[
E E
e.
Nameplates will be inspected prior to each shipnent and the Q
j inspection documented on "Fireshield Checksheet", R-7 ad " Cask Shipping Checksheet", R-8.
a.
3 Inspection Procedure kh C
a.
Verify that the nameplate information is legible and rot BD
-)-
covered or otherwise obliterated, b.
Carefully remove any labels or label adhesive from rnmeplate.
g Do not damage the rameplate.
9006280390 900621 z'
g l8 DR ADOCK 0710 1
h
$hy DATE 15$UED 10/10/80 SUPERSEDES ISSUE PAGE OF g
y 2
E E 3E ll @))
ISSUED SY1 J.I. Ibnori DATED:
REVIEW D ATE _t/91
- _.s SENERAllm3 ELECTRIC
="'
r
\\
%)
IRRADI ATION PR'OCE551NO OPER ATION 4
RADIOACTIVE PRODUCTS & SERVICES OPERATING PROCEDURE i
asCTioN CHAPTgn II. CASK /FIRESHIELD PAI!nBWJCE O.
Nameplates 3.
Inspection Procedure (continued)
I c.
Check that rameplate is attached securely:
- 1) Cask nameplates must be welded tre entire length of each side.
- 2) Fireshield rameplates need only four attactment points - one at each corner.
d.
Nameplates must rot be loose, bent, or otherwise damaged.
i Verify that the nameplate locaticr1 on the wooden fireshield is 90' away from e.
forklift openings in the pallet.
f.
Verify that the rameplate location en the large casks is approximately 45' away from cask lifting ears.
- 4. Irsta11ation a.
Obta$n necessary rameplate from RP&S Analyst or Custodian, I
b.
Weld the nameplate on tre cask using appropriate weld rod for tie material.
Nameplates must be attached to the cask in an area approximately 45' away from c.
cask lifting ears to prevent damage to rameplate fran forklift.
d.
Attach the rameplate to the fireshield using one of the following corner attactnent methods:
- 1) Wooden Fireshield - 4 corner attachment with wood screws.
- 2) Metal Fireshield - Sheet metal screws L
- Rivets
- Tack welds j-
- Nuts and bolts L
e.
Location must be 90 away frcin pallet opening on the woodel fireshield.
Becord nameplate change in the Cask PM Iogbook.
0 pass 2 op 2 IATsissuso 10/10/80 sueenssoas issus IW navision wo.
- issuno svi J.I. 7bnorio oATaos
-