ML15222A848

From kanterella
Jump to navigation Jump to search

ENT000637 - NUREG-1874, Recommended Screening Limits for Pressurized Thermal Shock (PTS) (March 2010)
ML15222A848
Person / Time
Site: Indian Point  Entergy icon.png
Issue date: 08/10/2015
From:
Entergy Nuclear Operations
To:
Atomic Safety and Licensing Board Panel
SECY RAS
References
RAS 28134, ASLBP 07-858-03-LR-BD01, 50-247-LR, 50-286-LR
Download: ML15222A848 (161)


Text

ENT000637 Submitted: August 10, 2015 NUREG-1874 Recommended Screening Limits for Pressurized Thermal Shock (PTS)

Office of Nuclear Regulatory Research

NUREG-1874 Recommended Screening Limits for Pressurized Thermal Shock (PTS)

Manuscript Completed: March 2007 Date Published: March 2010 Prepared by M.T. EricksonKirk 1 T.L. Dickson2 2

Oak Ridge National Laboratory Oak Ridge, TN 37831-6170 1

Office of Nuclear Regulatory Research

ii Abstract During plant operation, the walls of reactor pressure vessels (RPVs) are exposed to neutron radiation, resulting in localized embrittlement of the vessel steel and weld materials in the core area. If an embrittled RPV had a flaw of critical size and certain severe system transients were to occur, the flaw could propagate very rapidly through the vessel, resulting in a through-wall crack and challenging the integrity of the RPV. The severe transients of concern, known as pressurized thermal shock (PTS) events, are characterized by a rapid cooling of the internal RPV surface in combination with repressurization of the RPV. Advancements in its understanding and knowledge of materials behavior, its ability to model realistically plant systems and operational characteristics, and its ability to better evaluate PTS transients to estimate loads on vessel walls led the U.S. Nuclear Regulatory Commission to realize that the analysis conducted in the course of developing the PTS Rule in the 1980s contained significant conservatisms.

This report provides two options for using the updated technical basis described herein to develop PTS screening limits. Calculations reported herein show that the risk of through-wall cracking is low in all operating pressurized-water reactors, and current PTS regulations include considerable implicit margin.

Paperwork Reduction Act Statement The information collections contained in this NUREG are subject to the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.)., which were approved by the Office of Management and Budget, approval number 3150-0011.

Public Protection Notification The NRC may not conduct or sponsor, and a person is not required to respond to, a request for information or an information collection requirement unless the requesting document displays a currently valid OMB control number.

iii

iv Foreword The reactor pressure vessel (RPV) in a nuclear power plant is exposed to neutron radiation during normal operation. Over time, the vessel steel becomes more brittle in the region adjacent to the core. If a vessel had a preexisting flaw of critical size and certain severe system transients were to occur, this flaw could propagate rapidly through the wall of the vessel. The severe transients of concern, known as pressurized thermal shock (PTS) events, are characterized by a rapid cooling (i.e., thermal shock) of the internal RPV surface that may be combined with repressurization. Advancements in the state of knowledge in the more than 20 years since the U.S. Nuclear Regulatory Commission (NRC) promulgated its PTS Rule, (i.e.,

Title 10, Section 50.61, Fracture Toughness Requirements for Protection against Pressurized Thermal Shock Events, of the Code of Federal Regulations (10 CFR 50.61)) suggest that the embrittlement screening limits imposed by 10 CFR 50.61 are overly conservative. Therefore the NRC conducted a study to develop the technical basis for revising the PTS Rule in a manner consistent with the NRCs guidelines on risk-informed regulation. In early 2005, the Advisory Committee on Reactor Safeguards (ACRS) endorsed the staffs approach and its proposed technical basis. The staff documented the technical basis in an extensive set of reports (Section 4.1 of this report provides a complete list), which were then subjected to further internal reviews. Based on these reviews, the staff decided to modify certain aspects of the probabilistic calculations to refine and improve the model. This report documents these changes to the model and the results of an updated set of probabilistic calculations, which show the following:

For Plate-Welded Pressurized-Water Reactors (PWRs): Assuming that current operating conditions are maintained, the risk of PTS failure of the RPV is very low. Over 80 percent of operating PWRs have estimated through-wall cracking frequency (TWCF) values below 1x10-8/ry, even after 60 years of operation. After 40 years of operation the highest risk of PTS at any PWR is 2.0x10-7/ry. After 60 years of operation this risk increases to 4.3x10-7/ry. If the reference temperature screening limits proposed herein, which are based on limiting the yearly through wall cracking frequency to below a value of 1x10-6, are adopted, and if current operating practices are maintained then no plant will get within 30 F of the reference temperature limits within the first 40 years of operation. After 60 years of operation, the most embrittled plant will still be 17 F away from the reference temperature limits.

For Ring-Forged PWRs: Assuming that current operating conditions are maintained, the risk of PTS failure of the RPV is very low. All operating PWRs have estimated TWCF values below 1x10-8/ry, even after 60 years of operation. After 40 years of operation the highest risk of PTS at any PWR is 1.5x10-10/ry. After 60 years of operation this risk increases to 3.0x10-10/ry. If the reference temperature screening limits proposed herein, which are based on limiting the yearly through wall cracking frequency to below a value of 1x10-6, are adopted, and if current operating practices are maintained then no plant will get within 59 F of the reference temperature limits within the first 40 years of operation. After 60 years of operation, the most embrittled plant will still be 47 F away from the reference temperature limits.

These findings apply to all PWRs currently in operation in the United States. This report describes two options by which these findings can be incorporated into a revised version of 10 CFR 50.61.

Brian W. Sheron, Director Office of Nuclear Regulatory Research U.S. Nuclear Regulatory Commission v

vi Contents Abstract ........................................................................................................................................................iii Foreword ....................................................................................................................................................... v Contents ......................................................................................................................................................vii Executive Summary .....................................................................................................................................xi 1 Background and Objective.......................................................................................................... 1 2 Changes to the PTS Model.......................................................................................................... 3 2.1 RTNDT Epistemic Uncertainty Data Basis ................................................................................... 3 2.1.1 Review Finding ....................................................................................................................... 3 2.1.2 Model Change ......................................................................................................................... 3 2.2 FAVOR Sampling Procedures on RTNDT Epistemic Uncertainty ............................................... 4 2.2.1 Review Finding ....................................................................................................................... 4 2.2.2 Model Change ......................................................................................................................... 4 2.3 FAVOR Sampling Procedures on Other Variables..................................................................... 4 2.3.1 Review Finding ....................................................................................................................... 4 2.3.2 Model Change ......................................................................................................................... 4 2.4 Distribution of Repair Flaws....................................................................................................... 4 2.4.1 Review Finding ....................................................................................................................... 4 2.4.2 Model Change ......................................................................................................................... 5 2.5 Distribution of Underclad Flaws in Forgings.............................................................................. 7 2.5.1 Review Finding ....................................................................................................................... 7 2.5.2 Model Change ......................................................................................................................... 7 2.6 Embrittlement Trend Curve ........................................................................................................ 7 2.6.1 Review Finding ....................................................................................................................... 7 2.6.2 Model Change ......................................................................................................................... 7 2.7 LOCA Break Frequencies........................................................................................................... 7 2.7.1 Review Finding ....................................................................................................................... 7 2.7.2 Model Change ......................................................................................................................... 8 2.8 Temperature-Dependent Thermal Elastic Properties .................................................................. 8 2.8.1 Review Finding ....................................................................................................................... 8 2.8.2 Model Change ......................................................................................................................... 8 2.9 Upper-Shelf Fracture Toughness Model..................................................................................... 8 2.9.1 Review Finding ....................................................................................................................... 8 2.9.2 Model Change ......................................................................................................................... 8 2.10 Demonstration That the Flaws That Contribute to TWCF are Detectable by NDE Performed to ASME SC VIII Supplement 4 Requirements ......................................... 8 2.10.1 Review Finding................................................................................................................... 8 2.10.2 Reply................................................................................................................................... 8 3 PTS Screening Limits ............................................................................................................... 13 3.1 Overview................................................................................................................................... 13 3.2 Use of Plant-Specific Results to Develop Generic RT-Based Screening Limits ...................... 13 3.2.1 Justification of Approach ...................................................................................................... 13 3.2.2 Use of Reference Temperatures to Correlate TWCF ............................................................ 15 3.3 Plate-Welded Plants .................................................................................................................. 19 3.3.1 FAVOR 06.1 Results ............................................................................................................ 19 3.3.2 Estimation of TWCF Values and RT-Based Limits for Plate-Welded PWRs ...................... 25 3.3.3 Modification for Thick-Walled Vessels.................................................................................... 28 3.4 Ring-Forged Plants ................................................................................................................... 28 3.4.1 Embedded Flaw Sensitivity Study ........................................................................................ 29 vii

3.4.2 Underclad Flaw Sensitivity Study......................................................................................... 29 3.4.3 Modification for Thick-Walled Vessels ................................................................................ 31 3.5 Options for Regulatory Implementation of These Results........................................................ 31 3.5.1 Limitation on TWCF............................................................................................................. 32 3.5.2 Limitation on RT................................................................................................................... 42 3.6 Need for Margin........................................................................................................................ 47 3.6.1 Residual Conservatisms ........................................................................................................ 48 3.6.2 Residual Nonconservatisms .................................................................................................. 50 3.7 Summary ................................................................................................................................... 52 4 References................................................................................................................................. 55 4.1 PTS Technical Basis Citations.................................................................................................. 55 4.1.1 Summary ............................................................................................................................... 55 4.1.2 Probabilistic Risk Assessment .............................................................................................. 55 4.1.3 Thermal-Hydraulics .............................................................................................................. 55 4.1.4 Probabilistic Fracture Mechanics .......................................................................................... 56 4.2 Literature Citations ................................................................................................................... 58 Appendix A - Changes Requested Between FAVOR Version 05.1 and FAVOR Version 06.1.A-1 Appendix B - Review of the Literature on Subclad Flaws and a Technical Basis for Assigning Subclad Flaw Distributions.B-1 Appendix C - Sensitivity Study on an Alternative Embrittlement Trend Curve.C-1 Appendix D - Technical Basis for the Input Files to the FAVOR Code for Flaws in Vessel Forgings..D-1 viii

Figures Figure 1.1. Structure of documentation summarized by this report and by (EricksonKirk-Sum).

The citations for these reports in the text appear in italicized boldface to distinguish them from literature citations.............................................................................................. 1 Figure 2.1. Data on which the RTNDT epistemic uncertainty correction is based.................................. 3 Figure 2.2. Distribution of repair flaws in any weld repair cavity ........................................................ 6 Figure 2.3. Distribution of weld repair flaws through the vessel wall thickness .................................. 6 Figure 2.4. Flaw dimension and position descriptors adopted in FAVOR ........................................... 9 Figure 2.5. Distribution of through-wall position of cracks that initiate............................................... 9 Figure 2.6. Flaw depths that contribute to crack initiation probability in Beaver Valley Unit 1 when subjected to (left) medium- and large-diameter pipe break transients and (right) stuck-open valve transients at two different embrittlement levels......................... 10 Figure 2.7. Analysis of Palisades transients #65 (repressurization transient) and #62 (large-diameter primary-side pipe break transient) to illustrate what combinations of flaw size and location lead to non-zero conditional probabilities of crack initiation ....... 10 Figure 2.8. Probability of detection curve (Becker 02) ....................................................................... 11 Figure 3.1. TWCF distributions for Beaver Valley Unit 1 estimated for 32 EFPY and for a much higher level of embrittlement (Ext-B). At 32 EFPY the height of the zero bar is 62 percent................................................................................................................ 20 Figure 3.2. The percentile of the TWCF distribution corresponding to mean TWCF values at various levels of embrittlement......................................................................................... 20 Figure 3.3. Dependence of TWCF due to various transient classes on embrittlement as quantified by the parameter RTMAX-AW (curves are hand-drawn to illustrate trends)........ 23 Figure 3.4. Relationship between TWCF and RT due to various flaw populations (left: axial weld flaws, center: plate flaws, right: circumferential weld flaws). Eq. 3-5 provides the mathematical form of the fit curves shown here......................................................... 24 Figure 3.5. Graphical representation of Eqs. 3-5 and 3-6. The TWCF of the surface in both diagrams is 1x10-6. The top diagram provides a close-up view of the outermost corner shown in the bottom diagram. (These diagrams are provided for visualization purposes only; they are not a completely accurate representation of Eqs. 3-5 and 3-6 particularly in the very steep regions at the edges of the TWCF = 1x10-6 surface.) .. 26 Figure 3.6. Maximum RT-based screening criterion (1E-6 curve) for plate-welded vessels based on Eq. 3-6 (left: screening criterion relative to currently operating PWRs after 40 years of operation; right: screening criterion relative to currently operating PWRs after 60 years of operation). .............................................................................................. 27 Figure 3.7. Distribution of RPV wall thicknesses for PWRs currently in service (RVID2). This figure originally appeared as Figure 9.9 in NUREG-1806................................................................. 28 Figure 3.8. Effect of vessel wall thickness on the TWCF of various transients in Beaver Valley (all analyses at 60 EFPY). This figure originally appeared as Figure 9.10 in NUREG-1806............ 28 Figure 3.9. Relationship between TWCF and RT for forgings having underclad flaws..................... 30 Figure 3.10. Effect of vessel wall thickness on the TWCF of forgings having underclad flaws compared with results for plate-welded vessels (see Figure 3.7)...................................... 31 Figure 3.11. Estimated distribution of TWCF for currently operating PWRs using the procedure detailed in Section 3.5.1.................................................................................................... 37 Figure 3.12. Comparison of the distributions (red and blue histograms) of the various RT values characteristic of beltline materials in the current operating fleet projected to 48 EFPY with the TWCF vs. RT relationships (curves) used to define the proposed ix

PTS screening limits (see Figure 3.4 and Figure 3.9 for the original presentation of these relationships) ....................................................................................................... 41 Figure 3.13. Graphical comparison of the RT limits for plate-welded plants developed in Section 3.5.2 with RT values for plants at EOLE (from Table 3.3). The top graph is for plants having wall thickness of 9.5-in. and less, while the bottom graph is for vessels having wall thicknesses between 10.5 and 11.5 in............................ 47 Figure 3.14. Graphical comparison of the RT limits for ring-forged plants developed in Section 3.5.2 with RT values for plants at EOLE (from Table 3.3) ................................. 47 Tables Table 3.1. Summary of FAVOR 06.1 Results Reported in (Dickson 07b)........................................ 22 Table 3.2. Results of a Sensitivity Study Assessing the Effect of Underclad Flaws on the TWCF of Ring-Forged Vessels.............................................................................. 30 Table 3.3. RT and TWCF Values for Plate-Welded Plants Estimated Using the Procedure Described in Section 3.5.1 ............................................................................... 38 Table 3.4. RT and TWCF Values for Ring-Forged Plants Estimated Using the Procedure Described in Section 3.5.1 ............................................................................... 40 Table 3.5. RT Limits for PWRs ......................................................................................................... 46 Table 3.6. Non-Best-Estimate Aspects of the Models Used to Develop the RT-Based Screening Limits for PTS ................................................................................................. 51 Table 3.7. RT Limits for PWRs ......................................................................................................... 53 x

Executive Summary From 1999 through 2007, the U.S. Nuclear Regulatory Commission (NRC) conducted a study to develop the technical basis for revising the Pressurized Thermal Shock (PTS) Rule, as set forth in Title 10, Section 50.61, Fracture Toughness Requirements for Protection against Pressurized Thermal Shock Events, of the Code of Federal Regulations (10 CFR 50.61) in a manner consistent with the NRCs guidelines on risk-informed regulation. In early 2005, the Advisory Committee on Reactor Safeguards (ACRS) endorsed the staffs approach and its proposed technical basis. The staff documented the technical basis in an extensive set of reports (Section 4.1 of this report provides a complete list), which were then subjected to further internal reviews. Based on these reviews, the staff decided to modify certain aspects of the probabilistic calculations to refine and improve the model. This report documents these changes and the results of probabilistic calculations that provide the technical basis for the staffs development of a voluntary alternative to the PTS Rule.

This executive summary begins with a description of PTS, how it might occur, and its potential consequences for the reactor pressure vessel (RPV). This is followed by a summary of the current regulatory approach to PTS, which leads directly to a discussion of the motivations for conducting this project. Following this introductory information, the executive summary describes the approach used to conduct the study, and summarizes key findings and recommendations, which include a proposal for a revision to the PTS screening limits.

To provide a complete perspective on the current understanding of the risk of RPV failure arising from PTS, this executive summary draws not only on information presented in this report but also from the other technical basis reports listed in Section 4.1 of this report.

Description of PTS During the operation of a nuclear power plant, the RPV walls are exposed to neutron radiation, resulting in localized embrittlement of the vessel steel and weld materials in the area adjacent to the reactor core. If an embrittled RPV had an existing flaw of critical size and certain severe system transients were to occur, the flaw could propagate very rapidly through the vessel, resulting in a through-wall crack and challenging the integrity of the RPV. The severe transients of concern, known as PTS events, are characterized by a rapid cooling (i.e., thermal shock) of the internal RPV surface and downcomer, which may be followed by repressurization of the RPV. Thus, a PTS event poses a potentially significant challenge to the structural integrity of the RPV in a pressurized-water reactor (PWR).

A number of abnormal events and postulated accidents have the potential to thermally shock the vessel (either with or without significant internal pressure). These events include, among others, a pipe break in the primary pressure circuit, a stuck-open valve in the primary pressure circuit that later re-closes (causing re-pressurization of the primary), or a break of the main steamline. When such events are initiated by a break in the primary pressure circuit the water level drops as a result of leakage from the break. Automatic systems and operators provide makeup water in the primary system to prevent overheating of the fuel in the core. However, the makeup water is much colder than that held in the primary system. As a result, the temperature drop produced by rapid depressurization, coupled with the near-ambient temperature of the makeup water, produces significant thermal stresses in the hotter thick section steel wall of the RPV. For embrittled RPVs, these stresses could be sufficient to initiate a running crack, which could propagate all the way through the vessel wall. Such through-wall cracking of the RPV could result in core damage or, in rare cases, a large early release of radioactive material to the environment. Fortunately, the coincident occurrence of critical-size flaws, embrittled vessel steel and weld material, and a severe PTS transient is a very low-probability event. In fact, only a few operating PWRs are projected to even come close to the xi

current statutory limit (10 CFR 50.61) on the level of embrittlement during the first 40 years of operation assuming that current operating practices are maintained.

Current Regulatory Approach to PTS As set forth in 10 CFR 50.61, the PTS Rule requires licensees to monitor the embrittlement of their RPVs using a reactor vessel material surveillance program qualified under Appendix H, Reactor Vessel Material Surveillance Program Requirements, to 10 CFR Part 50, Domestic Licensing of Production and Utilization Facilities. The surveillance results are then used together with the formulae and tables in 10 CFR 50.61 to estimate the fracture toughness transition temperature (RTNDT) of the steels in the vessels beltline and how those transition temperatures increase as a result of irradiation damage that accumulates over the operational life of the vessel. For licensing purposes, 10 CFR 50.61 provides instructions on how to use these estimates of the effect of irradiation damage to estimate the value of RTNDT that will occur at end of license (EOL), a value called RTPTS. The screening limits provided in 10 CFR 50.61 restrict the maximum values of RTNDT permitted during the plants operational life to

+270 F (132 C) for axial welds, plates, and forgings, and +300 F (149 C) for circumferential welds.

These screening limits were selected based upon a limit of 5x10-6 events per year on the annual probability of developing a through-wall crack (RG 1.154). Should RTPTS exceed these screening limits, 10 CFR 50.61 requires the licensee to either take actions to keep RTPTS below the screening limits. These actions include implementing reasonably practicable flux reductions to reduce the embrittlement rate or by deembrittling the vessel by annealing (RG 1.162), or performing plant-specific analyses to demonstrate that operating the plant beyond the 10 CFR 50.61 screening limits does not pose an undue risk to the public (RG 1.154).

While no currently operating PWR has an RTPTS value that is projected to exceed the 10 CFR 50.61 screening limits before EOL, several plants are close to the limit (3 are within 2 F, while 10 are within 20 F). Those plants are likely to exceed the screening limits during the 20-year license renewal period that many operators are currently seeking or have already received. Moreover, some plants maintain their RTPTS values below the 10 CFR 50.61 screening limits by implementing flux reductions (low-leakage cores, ultra-low-leakage cores), which are fuel management strategies that can be economically deleterious in a deregulated marketplace. Thus, the 10 CFR 50.61 screening limits can restrict both the licensable and economic lifetime of PWRs.

Motivation for This Project It is now widely recognized that the state of knowledge and data limitations in the early 1980s necessitated conservative treatment of several key parameters and models used in the probabilistic calculations that provided the technical basis for the current PTS Rule. The most prominent of these conservatisms includes the following factors:

highly simplified treatment of plant transients (very coarse grouping of many operational sequences (on the order of 105) into very few groups (approximately 10), necessitated by limitations in the computational resources needed to perform multiple thermal-hydraulic (TH) calculations) lack of any significant credit for operator action characterization of fracture toughness using RTNDT, which has an intentional conservative bias use of a flaw distribution that places all flaws on the interior surface of the RPV, and, in general, contains larger flaws than those usually detected in service xii

a modeling approach that treated the RPV as if it were made entirely from the most brittle of its constituent materials (welds, plates, or forgings) a modeling approach that assessed RPV embrittlement using the peak fluence over the entire interior surface of the RPV These factors indicate the high likelihood that the current 10 CFR 50.61 PTS screening limits are unnecessarily conservative. Consequently, the NRC staff believes that reexamining the technical basis for these screening limits, based on a modern understanding of all the factors that influence PTS, would most likely provide strong justification for substantially relaxing these limits. For these reasons, the NRC undertook this study with the objective of developing the technical basis to support a risk-informed revision of the PTS Rule and the associated PTS screening limits.

Approach As illustrated in the following figure, three main models (shown as solid blue squares), taken together, permit estimation of the annual frequency of through-wall cracking in an RPV:

probabilistic risk assessment (PRA) event sequence analysis TH analysis probabilistic fracture mechanics (PFM) analysis Acceptance Criterion Probabilistic Estimation of Through-Wall Cracking Frequency for TWC Frequency Established consistent with Probabilistic Thermal PRA Event

  • 1986 Commission safety goal Fracture P(t), T(t), & Hydraulic Sequence Sequence policy statement Analysis HTC(t) Analysis Definitions Analysis (FAVOR) (RELAP) (SAPPHIRE)
  • RG1.174 Conditional Probability of Thru-Wall Screening Limit Cracking, CPTWC Development Yearly Frequency of [CPTWC]

Yearly Frequency of Thru-Wall x Cracking [freq]

Sequence Frequencies Thru-Wall Cracking freq Screening Limit Vessel damage, age, or operational metric Schematic showing how a probabilistic estimate of TWCF is combined with a TWCF acceptance criterion to arrive at a proposed revision of the PTS screening limit First, a PRA event sequence analysis is performed to postulate the sequences of events that may cause a PTS challenge to RPV integrity and to estimate the frequency with which such sequences might occur.

The event sequence definitions are then passed to a TH model that estimates the temporal variation of temperature, pressure, and heat-transfer coefficient in the RPV downcomer, which is characteristic of each sequence definition. These temperature, pressure, and heat-transfer coefficient histories are then passed to a PFM model that uses the TH output, along with other information concerning RPV design and construction materials, to estimate the time-dependent driving force to fracture produced by a particular event sequence. The PFM model then compares this estimate of fracture-driving force to the fracture toughness, or fracture resistance, of the RPV steel. Performing this comparison for many simulated vessels and xiii

flaws permits estimation of the probabilities that a crack could grow to sufficient size that it would penetrate all the way through the RPV wall (assuming that a particular sequence of events actually occurs).

The final step in the analysis involves a simple matrix multiplication of the probability distribution of through-wall cracking (from the PFM analysis) with the distribution of frequencies at which a particular event sequence could occur (as defined by the PRA analysis). This product establishes an estimate of the distribution of the annual frequency of through-wall cracking that could occur at a particular plant after a particular period of operation when subjected to a particular sequence of events. The annual frequency distribution of through-wall cracking is then summed for all event sequences to estimate the total annual frequency distribution of through-wall cracking for the vessel. Performance of such analyses for various operating lifetimes provides an estimate of how the distribution of annual frequency of through-wall cracking would vary over the lifetime of the plant.

Performance of the probabilistic calculations just described establishes the technical basis for a revised PTS Rule within an integrated systems analysis framework. The staffs approach considers a broad range of factors that influence the likelihood of vessel failure during a PTS event, while accounting for uncertainties in these factors across a breadth of technical disciplines. Two central features of this approach are a focus on the use of realistic input values and models (wherever possible), and an explicit treatment of uncertainties (using currently available uncertainty analysis tools and techniques). Thus, the current approach improves upon that employed in SECY-82-465, Pressurized Thermal Shock, dated November 23, 1982, which included intentional and unquantified conservatisms in many aspects of the analysis, and treated uncertainties implicitly by incorporating them into the models.

Key Findings The findings from this study are divided into five topical areas(1) the expected magnitude of the TWCF for currently anticipated operational lifetimes, (2) the material factors that dominate PTS risk, (3) the transient classes that dominate PTS risk, (4) the applicability of these findings (based on detailed analyses of three PWRs) to PWRs in general, and (5) the annual limit on TWCF established consistent with current guidelines on risk-informed regulation. In this summary, the conclusions are presented in boldface italic, while the supporting information is shown in regular type.

TWCF Magnitude for Currently Anticipated Operational Lifetimes The degree of PTS challenge is low for currently anticipated lifetimes and operating conditions.

o For Plate-Welded PWRs: Assuming that current operating conditions are maintained, the risk of PTS failure of the RPV is very low. Over 80 percent of operating PWRs have estimated TWCF values below 1x10-8/ry, even after 60 years of operation. After 40 years of operation the highest risk of PTS at any PWR is 2.0x10-7/ry. After 60 years of operation this risk increases to 4.3x10-7

/ry. If the RT screening limits proposed herein, which are based on limiting the yearly through wall cracking frequency to below a value of 1x10-6, are adopted, and if current operating practices are maintained then no plant will get within 30 F of the RT limits within the first 40 years of operation. After 60 years of operation, the most embrittled plant will still be 17 F away from the RT limits.

o For Ring-Forged PWRs: Assuming that current operating conditions are maintained, the risk of PTS failure of the RPV is very low. All operating PWRs have estimated TWCF values below 1x10-8/ry, even after 60 years of operation. After 40 years of operation the highest risk of PTS at any PWR is 1.5x10-10/ry. After 60 years of operation this risk increases to 3.0x10-10/ry. If the RT screening limits proposed herein, which are based on limiting the yearly through wall cracking xiv

frequency to below a value of 1x10-6, are adopted, and if current operating practices are maintained then no plant will get within 59 F of the RT limits within the first 40 years of operation. After 60 years of operation, the most embrittled plant will still be 47 F away from the RT limits.

Material Factors and Their Contributions to PTS Risk Axial flaws, and the toughness properties that can be associated with such flaws, control nearly all of the TWCF.

o Plate-Welded Vessels Axial flaws are much more likely than circumferential flaws to propagate through the RPV wall because the applied fracture-driving force increases continuously with increasing crack depth for an axial flaw. Conversely, circumferentially oriented flaws experience a driving-force peak mid-wall, providing a natural crack arrest mechanism. It should be noted that crack initiation from circumferentially oriented flaws is likely; only their through-wall propagation is much less likely (relative to axially oriented flaws).

The toughness properties that can be associated with axial flaws control nearly all of the TWCF. These include the toughness properties of plates and axial welds at the flaw locations.

Conversely, the toughness properties of both circumferential welds and forgings have little effect on the TWCF of plate-welded PWRs because these can be associated only with circumferentially oriented flaws.

o Ring-Forged Vessels As with plate-welded PWRs, axial flaws are again much more likely than circumferential flaws to propagate through the RPV wall. However, because there are no axial welds in ring-forged vessels, the axial flaws that can be associated with these welds are absent. However, for particular combinations of forging chemistry and cladding heat input, underclad cracks can form in the forging. As implied by the name, these cracks form in the forging just below the cladding layer, and they form perpendicular to the direction in which the clad weld layer was deposited (i.e., axially). Therefore, the toughness properties that can be associated with these axial flaws (i.e., that of the forging) control nearly all of the TWCF in ring-forged vessels.

Transients and Their Contributions to PTS Risk Transients involving primary-side faults are the dominant contributors to TWCF, while transients involving secondary-side faults play a much smaller role.

o The severity of a transient is controlled by a combination of three factors:

initial cooling rate, which controls the thermal stress in the RPV wall minimum temperature of the transient, which controls the resistance of the vessel to fracture pressure retained in the primary system, which controls the pressure stress in the RPV wall o The significance of a transient (i.e., how much it contributes to PTS risk) depends on these three factors and the likelihood that the transient will occur.

o The analysis considered transients in the following classes:

primary-side pipe breaks stuck-open valves on the primary side main steamline breaks xv

stuck-open valves on the secondary side feed-and-bleed steam generator tube rupture mixed primary and secondary initiators o Of these, transients in the first two categories were responsible for 90 percent or more of the PTS risk, while transients in the third category were responsible for nearly all of the remainder.

For medium- to large-diameter primary-side pipe breaks, the fast-to-moderate cooling rates and low downcomer temperatures (generated by rapid depressurization and emergency injection of low-temperature makeup water directly to the primary system) combine to produce a high-severity transient. Despite the moderate-to-low likelihood that these transients will occur, their severity (if they do occur) makes them significant contributors to the total TWCF.

For stuck-open primary-side valves that later reclose, the repressurization associated with valve reclosure coupled with low temperatures in the primary system combine to produce a high-severity transient. This, coupled with a high likelihood of transient occurrence, makes stuck-open primary-side valves that may later reclose significant contributors to the total TWCF.

The small or negligible contribution of all secondary-side transients (main steamline break, stuck-open secondary valves) results directly from the lack of low temperatures in the primary system. For these transients, the minimum temperature of the primary system for times of relevance is controlled by the boiling point of water in the secondary system (212 F (100 C) or above). At these temperatures, the fracture toughness of the embrittled RPV steel is still sufficiently high to resist vessel failure in most cases.

Applicability of These Findings to PWRs in General Credits for operator action, while included in the analysis, do not influence these findings in any significant way. Operator action credits can influence dramatically the risk-significance of individual transients. Therefore, a best estimate analysis needs to include appropriate credits for operator action because it is not possible to establish a priori if a particular transient will make a large contribution to the total risk. Nonetheless, the results of the analyses demonstrate that these operator action credits have a small overall effect on a plants total TWCF, for reasons detailed below.

o Medium- and Large-Diameter Primary-Side Pipe Breaks: No operator actions are modeled for any break diameter because, for these events, the safety injection systems do not fully refill the upper regions of the reactor coolant system. Consequently, operators would never take action to shut off the pumps.

o Stuck-Open Primary-Side Valves That May Later Reclose: The PRA model includes reasonable and appropriate credit for operator actions, such as throttling of the high-pressure injection (HPI) system. However, these credits have a small influence on the estimated values of vessel failure probability attributable to transients caused by a stuck-open valve in the primary pressure circuit (SO-1 transients) because the credited operator actions only prevent repressurization when SO-1 transients initiate from hot zero power (HZP) conditions and the operators act promptly (within 1 minute) to throttle the HPI. Complete removal of operator action credits from the model only increases slightly the total risk associated with SO-1 transients.

o Main Steamline Breaks: For the overwhelming majority of transients caused by a main steamline break, vessel failure is predicted to occur between 10 and 15 minutes after transient initiation because the thermal stresses associated with the rapid cooldown reach their maximum within this xvi

timeframe. Thus, all of the long-term effects (isolation of feedwater flow, timing of the high-pressure safety injection control) that can be influenced by operator actions have no effect on vessel failure probability because such factors influence the progression of the transient after failure has occurred (if it occurs at all). Only factors affecting the initial cooling rate (i.e., plant power level at time of transient initiation, break location inside or outside of containment) can influence the conditional probability of through-wall cracking (CPTWC), and operator actions do not influence these factors in any way.

Because the severity of the most significant transients in the dominant transient classes is controlled by factors that are common to PWRs in general, the TWCF results presented herein can be used with confidence to develop revised PTS screening criteria that apply to the entire fleet of operating PWRs.

o Medium- and Large-Diameter Primary-Side Pipe Breaks: For these break diameters, the fluid in the primary system cools faster than the wall of the RPV. In this situation, only the thermal conductivity of the steel and the thickness of the RPV wall control the thermal stresses and, thus, the severity of the fracture challenge. Perturbations in the fluid cooldown rate controlled by break diameter, break location, and season of the year do not play a significant role. Thermal conductivity is a physical property, so it is very consistent for all RPV steels, and the thicknesses of the three RPVs analyzed are typical of most PWRs. Consequently, the TWCF contribution of medium- to large-diameter primary-side pipe breaks is expected to be consistent from plant-to-plant and can be well represented for all PWRs by the analyses reported herein.

o Stuck-Open Primary-Side Valves That May Later Reclose: A major contributor to the risk-significance of SO-1 transients is the return to full system pressure once the valve recloses. The operating and safety relief valve pressures of all PWRs are similar. Additionally, as previously noted, operator action credits affect only slightly the total TWCF associated with this transient class.

o Main Steamline Breaks: Since main steamline breaks fail early (within 10-15 minutes after transient initiation), only factors affecting the initial cooling rate can have any influence on the CPTWC values. Operator actions do not influence these factors, which include the plant power level at event initiation and the location of the break (inside or outside of containment), in any way.

Sensitivity studies performed on the TH and PFM models to investigate the effect of credible model variations on the predicted TWCF values revealed that only vessel wall thickness was a factor so significant as to require modification of the baseline results for the three detailed study plants.

This finding resulted in the revised PTS screening limits being expressed as a function of RPV wall thickness.

An investigation of design and operational characteristics for five additional PWRs revealed no differences in sequence progression, sequence frequency, or plant TH response significant enough to call into question the applicability of the TWCF results from the three detailed plant analyses to PWRs in general.

An investigation of potential external initiating events (e.g., fires, earthquakes, floods) revealed that the contribution of those events to the total TWCF can be regarded as negligible.

xvii

Annual Limit on TWCF The current guidance provided by Regulatory Guide 1.174 for large early release is conservatively applied to setting an acceptable annual TWCF limit of 1x10-6 events/year.

o While many post-PTS accident progressions led only to core damage (which suggests a TWCF limit of 1x10-5 events/year in accordance with Regulatory Guide 1.174, Revision 1, An Approach for Using Probabilistic Risk Assessment in Risk-Informed Decisions on Plant-Specific Changes to the Licensing Basis, issued November 2002), uncertainties in the accident progression analysis led to the recommendation to adopt the more conservative limit of 1x10-6 events/year based on the large early release frequency.

Recommended Revision of the PTS Screening Limits The NRC staff recommends using different RT-metrics to characterize the resistance of an RPV to fractures initiating from different flaws at different locations in the vessel. Specifically, the staff recommends an RT for flaws occurring along axial weld fusion lines (RTMAX-AW), another for the embedded flaws occurring in plates (RTMAX-PL), a third for flaws occurring along circumferential weld fusion lines (RTMAX-CW), and a fourth for embedded and/or underclad cracks in forgings (RTMAX-FO).

These values can be estimated based mostly on the information in the NRCs Reactor Vessel Integrity Database (RVID). The staff also recommends using these different RT values together to characterize the fracture resistance of the vessels beltline region, recognizing that the probability of a vessel fracture initiating from different flaw populations varies considerably in response to factors that are both 400

-6 1x10 /ry TWCF limit understood and predictable. Correlations between these RT values and the TWCF attributable to 350 different flaw populations show little plant-to-plant Simplified Implementation RT 269F, and MAX-AW variability because of the general similarity of PTS 300 RT 356F, and MAX-PL RT + RT 538F.

challenges among plants. MAX-AW MAX-PL RTMAX-PL [oF]

250 This report proposes a formula to estimate the total Plate Welded Plants TWCF for a vessel based only on these RT values 200 at 48 EFPY (EOLE) and on the vessel wall thickness, and uses this formula to estimate the TWCF values for all 150 operating PWRs. Currently none of these estimates exceeds the 1x10-6/ry limit during either current or 100 extended (through 60 years) operations. One option that may be considered when implementing 50 these results in a revised version of 10 CFR 50.61 is to simply require licensees to ensure that these 0 TWCF estimates remain below the 1x10-6/ry limit. 0 50 100 150 200 250 300 An alternative implementation option is to use the equation presented herein that relates TWCF to the RTMAX-AW [oF]

various RT-metrics to transform the 1x10-6/ry limit Comparison of RT-based screening limits into limits on the various RT values. The staff has (curves or dashed lines) with assessment established candidate RT-based screening limits by points for operating plate-welded PWRs at setting the total TWCF equal to 1x10-6/ry. The figure EOLE. Limits are shown for vessels to the right graphically represents one set of these having wall thicknesses of 9.5 inches or screening limits along with an assessment of all less. This report provides similarly defined operating plate-welded PWRs relative to the limits for thicker vessels and for ring-proposed limits at the end of license extension (the forged vessels.

projected plant RT-values for EOLE reported in this figure are premised on the assumption that current xviii

operating practices are maintained). In this figure, the region of the graphs between the red locus and the origin has TWCF values below the 1x106/ry acceptance criterion, so the staff would consider these combinations of RTs to be acceptable and require no further analysis. By contrast, the region of the graph outside of either the red locus has TWCF values above the 1x10-6/yr acceptance criterion, indicating the need for additional analysis or other measures to justify continued plant operation. Clearly, operating PWRs will not exceed the 1x10 6/ry limit, even after 60 years of operation. This separation of operating plants from the screening limits contrasts markedly with the current regulatory situation in which several plants are within 1 F (0.5 C) of the screening limits set forth in 10 CFR 50.61 after only 40 years of operation.

Aside from relying on RT-metrics that differ from those currently used in 10 CFR 50.61, these proposed implementation options also differ from the current approach in terms of the absence of a margin term. Use of a margin term is appropriate to account for (at least approximately) factors that occur in application, but that were not considered in the analysis upon which the screening limits are based. For example, the current 10 CFR 50.61 margin term accounts for uncertainty in copper, nickel, and initial RTNDT values. However, the model adopted in this study explicitly considers uncertainty in all of these variables and models these uncertainties as being larger (a conservative representation) than would be appropriate in any plant-specific application. Consequently, use of the 10 CFR 50.61 margin term with the new screening limits proposed herein is inappropriate. In general, the following three reasons suggest that use of any margin term with the proposed screening limits is inappropriate:

(1) The TWCF values used to establish the screening limits are 95th percentile values.

(2) The results from the staffs three plant-specific analyses apply to PWRs in general.

(3) While certain aspects of the modeling cannot reasonably be represented as best estimates, there is, on balance, a conservative bias to these non-best-estimate aspects of the analysis because residual conservatisms in the model far outweigh residual nonconservatisms.

Assessing the Continued Appropriateness of the Recommended PTS Screening Limits As described in this and in companion reports, the screening limits the staff has recommended for PTS are premised on the view that the mathematical model of PTS we have described is an appropriate representation of PTS events, both in terms of the likelihood of their occurance as well and in terms of their effect on the RPV were they to occur. Because the appropriatness of the staffs model of PTS may change in the future due to changes in operating practice, changes in initiating event frequencies, changes in radiation damage mechanisms, and potential changes in other factors, the staff should periodically evaluate the PTS model described here for appropriateness. Should these evaluations reveal a significant departure between this model and physical reality then appropriate actions, if any, could be taken.

xix

xx Chapter 1 - Background and Objective In early 2005, the U.S. Nuclear Regulatory aspects of the probabilistic calculations to refine Commission (NRC) staff completed a series of and improve the model. The purpose of this reports detailing the technical basis for a risk- report is threefold(1) to document the changes informed revision of the pressurized thermal made to the PTS models based on the post-shock (PTS) Rule (Title 10, Section 50.61, ACRS reviews, (2) to report the results of the Fracture Toughness Requirements for new computations, and (3) to make Protection against Pressurized Thermal Shock recommendations on the use of these results to Events, of the Code of Federal Regulations revise screening limits for PTS. Chapter 2 of (10 CFR 50.61)). Figure 1.1 depicts these this report details changes to the model since reports; Section 4.1 includes the full references. publication of NUREG-1806 (EricksonKirk-Both an external peer review panel and the Sum) while Chapter 3 describes the results of Advisory Committee for Reactor Safeguards the calculations and recommendations on (ACRS) (ACRS 05) critiqued and approved the revised screening limits for PTS. This report reports (see Appendix B to NUREG-1806 does not provide a comprehensive summary of (EricksonKirk-Sum) for details). Following NRC activities undertaken over the last 7 years ACRS review, these reports were then subjected to develop the technical basis for a risk-informed to further internal reviews. Based on these revision to 10 CFR 50.61 (see (EricksonKirk-reviews, the staff decided to modify certain Sum) for these details).

Summary Report - NUREG-1806 PFM TH PRA Models, Validation, & Procedures

  • Procedures, Uncertainty, & Experimental
  • TH Model: Bessette, D., Thermal
  • Procedures & Uncertainty: Whitehead, Validation: EricksonKirk, M.T., et al., Hydraulic Analysis of Pressurized D.W., et al., PRA Procedures and Probabilistic Fracture Mechanics: Thermal Shock, NUREG/1809. Uncertainty for PTS Analysis, NUREG/CR-Models, Parameters, and Uncertainty 6859.

Treatment Used in FAVOR Version 04.1,

  • RELAP Procedures & Experimental NUREG-1807. Validation: Fletcher, C.D., et al.,
  • Uncertainty Analysis Methodology: Siu, N.,

RELAP5/MOD3.2.2 Gamma Assessment Uncertainty Analysis and Pressurized

  • FAVOR for Pressurized Thermal Shock Thermal Shock, An Opinion.
  • Theory Manual: Williams, P.T., et al., Applications, NUREG/CR-6857.

Fracture Analysis of Vessels - Oak

  • Experimental Benchmarks: Reyes, J.N.,

Ridge, FAVOR v04.1, Computer Code: et. al., Final Report for the OSU APEX-Theory and Implementation of CE Integral Test Facility, NUREG/CR-Algorithms, Methods, and 6856.

Correlations, NUREG/CR-6854.

  • Users Manual: Dickson, T.L., et al.,
  • Experimental Benchmarks: Reyes, J.N.,

Fracture Analysis of Vessels - Oak Scaling Analysis for the OSU APEX-CE Ridge, FAVOR v04.1, Computer Code: Integral Test Facility, NUREG/CR-6731.

Users Guide, NUREG/CR-6855.

  • Uncertainty: Chang, Y.H., et al., Thermal
  • V&V Report: Malik, S.N.M., FAVOR Hydraulic Uncertainty Analysis in Code Versions 2.4 and 3.1 Pressurized Thermal Shock Risk Verification and Validation Summary Assessment, NUREG/CR-6899.

Report, NUREG-1795.

  • Flaw Distribution: Simonen, F.A., et al.,

A Generalized Procedure for Generating Flaw-Related Inputs for the FAVOR Code, NUREG/CR-6817, Rev. 1.

  • Baseline: Dickson, T.L., et al.,
  • Baseline: Arcieri, W.C., et al., RELAP5
  • Beaver: Whitehead, D.W., et al., Beaver Electronic Archival of the Results of Thermal Hydraulic Analysis to Support Valley PTS PRA Pressurized Thermal Shock Analyses for PTS Evaluations for the Oconee-1, Beaver Valley, Oconee, and Palisades Beaver Valley-1, and Palisades Nuclear
  • Palisades: Whitehead, D.W., et al.,

ORNL/NRC/LTR-04/18.

  • Sensitivity Studies: Arcieri, W.C., et al.,

RELAP5/MOD3.2.2 Gamma Results for Palisades PTS PRA

  • Sensitivity Studies: EricksonKirk, M.T., Palisades 1D Downcomer Sensitivity
  • External Events: Kolaczkowski, A.M., et al.,

et al., Sensitivity Studies of the Study Estimate of External Events Contribution Probabilistic Fracture Mechanics Model to Pressurized Thermal Shock Risk Used in FAVOR Version 03.1, NUREG-

  • Consistency Check: Junge, M., PTS 1808. Consistency Effort
  • Generalization: Whitehead, D.W., et al.,

Generalization of Plant-Specific PTS Risk Results to Additional Plants Figure 1.1. Structure of documentation summarized by this report and by (EricksonKirk-Sum). The citations for these reports in the text appear in italicized boldface to distinguish them from literature citations.

1

2 Chapter 2 - Changes to the PTS Model Following ACRS review and acceptance of the 2.1.1 Review Finding staffs methodology for developing probabilistic estimates of the risk of through-wall cracking of From the descriptions of the parameters RTLB a pressurized-water reactor (PWR) vessel caused (lower bound reference temperature) and To by PTS (see the reports detailed in Section 4.1 of (fracture toughness reference temperature) this report), these reports were subjected to provided in the documentation, it seems that further internal reviews and quality control these two parameters should have a more checks. On the basis of these reviews, the NRC systematic relationship and, in particular, that staff decided that certain aspects of the RTLB should always be greater than or equal to probabilistic calculations should be refined or To. Nevertheless, Figure 2.1, which displays the improved. These aspects, which are listed data on which the RTNDT epistemic uncertainty below, are described in both the remainder of correction is based, shows that RTLB can be this chapter and in Appendix A to this report. considerably less than To. Is there a problem with our understanding of how RTLB and To Section 2.1: Data basis for the reference relate to one another, or is there some temperature nil ductility (RTNDT) epistemic inconsistency in the data shown in Figure 2.1?

uncertainty correction 50 Section 2.2: RTNDT epistemic uncertainty correction: sampling procedures 0 Section 2.3: Fracture Analysis of Vessels: -50 RT LB [ F]

Oak Ridge (FAVOR) computer code o

-100 sampling procedures on other variables Section 2.4: The distribution of flaws in -150 Data repair welds -200 RTLB = To Section 2.5: The distribution of subclad flaws in forgings -250

-200 -150 -100 -50 0 50 Section 2.6: The relationship used to predict o T o [ F]

embrittlement based on exposure and on composition variables Figure 2.1. Data on which the RTNDT epistemic Section 2.7: The upper-shelf fracture uncertainty correction is based toughness model Section 2.8: The temperature dependence of 2.1.2 Model Change thermal-elastic properties Section 2.9: Loss-of coolant accident The review correctly identifies that the data in (LOCA) break frequencies Figure 2.1 for which RTLB falls below To are erroneous. The change specification for the Additionally, while not resulting in a model Fracture Analysis of VesselsOak Ridge change, discussion is included in Section 2.10 (FAVOR) Code detailed in Appendix A discusses the ability of nondestructive provides a detailed explanation of the origins of examination (NDE) techniques to detect and size these erroneous data and develops a revised the flaws found to be risk-significant for PTS. epistemic uncertainty correction for RTNDT that does not rely on these data.

2.1 RTNDT Epistemic Uncertainty Data Basis 3

2.2 FAVOR Sampling Procedures on 2.3.2 Model Change RTNDT Epistemic Uncertainty The NRC performed a comprehensive review of 2.2.1 Review Finding the FAVOR uncertainty sampling strategy. On the basis of this review, the staff decided that, in addition to the RTNDT epistemic uncertainty The FAVOR code uses an RTNDT fracture discussed in Section 2.2, the uncertainty on the toughness indexing parameter and a Master following variables is more appropriately Curve Approach fracture toughness indexing sampled outside of the flaw loop, requiring a parameter (To) to estimate material toughness modification of FAVOR 04.1:

properties. The sampling of the RTNDT-To correction parameter in the Monte Carlo process (used in the FAVOR code), may affect the the unirradiated value of RTNDT variation that is seen in the results for the standard deviation on copper example plants. Currently the correction is standard deviation on nickel sampled inside the flaw loop so that each flaw is potentially assigned a different correction. It The FAVOR change specification details both may be more appropriate to sample the the rationale supporting these changes and how correction outside of the flaw loop so that the they are implemented in FAVOR Version 06.1.

correction is sampled once for each material for each vessel simulation. 2.4 Distribution of Repair Flaws 2.2.2 Model Change 2.4.1 Review Finding The review finding correctly identifies that it is To develop the sample flaw distributions as more appropriate to sample the uncertainty in input to the FAVOR code, Pacific Northwest the RTNDT-To correction parameter outside of the National Laboratory (PNNL) assumed that flaw loop (but still inside the vessel loop). The 2 percent of the volume of weld seams consisted previous sampling procedure simulated a degree of repair welds. The repair welds were assumed of uncertainty in the unirradiated fracture to be uniformly distributed through the toughness transition temperature that is submerged metal arc weld (SMAW) thickness.

unrealistic, a deficiency reconciled by the new Since repairs typically intersect the surface, it is sampling procedure. The FAVOR change possible that flaws associated with repairs would specification details both the rationale be preferentially located adjacent to the outside supporting this change and how it is diameter (OD) or inside diameter (ID) surfaces implemented in FAVOR Version 06.1. of the RPV. The extra flaws associated with repairs are typically located at the deepest point 2.3 FAVOR Sampling Procedures on of the repair. Examination of the repairs detailed Other Variables in Section 5.7 of NUREG/CR-6471, Volume 2, Characterization Of Flaws in U.S. Reactor Pressure Vessels: Density and Distribution of 2.3.1 Review Finding Flaw Indications in PVRUF, indicates the deepest part of the excavation cavity would be Similar to the comment made in Section 2.2.1 more often associated with the surface (or within regarding the location in FAVOR at which the 2 inches of the surface) than with the interior RTNDT epistemic uncertainty correction is regions of the plate or weld (Schuster 98).

sampled, the location of other sampled Accordingly, it seems reasonable to increase the parameters (e.g., copper, copper variability, proportion of the flaw distribution that should be nickel) may not be most appropriately placed attributed to weld repairs from the current within the flaw loop.

2 percent to some higher value. The higher value should be associated with the typical area 4

density of weld repair along weld seams. The with respect to the depth of the excavation current approach uses a 2-percent contribution, cavity. However, Figure 2.3 shows that weld which was chosen so that it would be a bound to repair areas occur with much higher frequency the observed 1.5-percent proportion of weld close to the surfaces of the vessel than they do at repair in the Pressure Vessel Research Users mid-wall thickness, as noted in Section 2.4.1.

Facility (PVRUF) vessel. The 1.5-percent value Taken together, this information indicates that a seems to have been calculated on a volume flaw from a weld repair is more likely to be basis. encountered close to the ID or OD surface than it is at the mid-wall thickness, a fact not well (1) What is the proportion of weld repair modeled by the approach adopted in FAVOR associated with the weld seams on the Version 04.1.

PVRUF vessel near the ID surface of the vessel on an area rather than a volume basis? FAVOR currently uses as input a blended flaw distribution for welds. The flaws placed in the (2) What is the expected or calculated effect of blended distribution are scaled in proportion to this change in the assumptions regarding the fusion area of the different welding repair flaw distributions on the TWCFs? processes used to fabricate the vessel. Because of this approach, it is not possible, without 2.4.2 Model Change significant recoding, to specify a through thickness distribution of repair weld flaws that is Regarding the first question in Section 2.4.1, it biased toward the surfaces while maintaining a is correctly noted that the judgment to include 2- random through-thickness distribution percent repair flaws in the flaw distribution used appropriate for submerged are weld (SAW) and in the baseline PTS analysis was made on the SMAW flaws. Therefore, to account for the basis that a 2-percent repair weld volume nonlinear through-thickness distribution of weld exceeded the proportional volume of weld flaws the 2-percent blending factor currently repairs to original fabrication welds observed in used for repair welds will be modified on the any of the PNNL work (the largest volume of following bases:

weld repairs relative to original fabrication welds was 1.5 percent). However, flaws in Only flaws within 3/8T of the inner diameter welds are almost always fusion-line flaws, can contribute to the vessel failure which suggests that their number scales in probability. Because PTS transients are proportion to weld fusion line area and not in dominated by thermal stresses, flaws buried proportion to weld volume. To address this in the vessel wall more deeply than 3/8T do issue, PNNL reexamined the relative proportion not have a high enough driving force/low of repair welds that occur on an area rather than enough fracture toughness to initiate.

on a volume basis. PNNL determined that the ratio of weld repair fusion area to original In Figure 2.3, 3/8T corresponds to 3 inches fabrication fusion area is 1.8 percent for the on the x-axis. The curve fit to the data PVRUF vessel. Thus, the input value of 2 indicates that 79 percent of all repair flaws percent used in the FAVOR calculations can still occur from 0 to 3/8T of the outer surfaces of be regarded as bounding. the vessel. Figure 2.3 also indicates that 7 percent of all repair flaws occur between Regarding the second question in Section 2.4.1, 5/8T and 1T from the outer surfaces of the FAVOR does assumes that a simulated flaw is vessel. Therefore 43 percent equally likely to occur at any location through (i.e., (79%+7%)/2) of all repair flaws occur the vessel wall thickness. Upon further between the ID and the 3/8T position in the consideration the staff has determined that this vessel wall.

model is incorrect for flaws occurring in repair welds. Figure 2.2 shows that if a flaw forms in a weld repair it is equally likely to occur anywhere 5

FAVORs current assumption of a random through-wall distribution of repair flaws To account for this underestimation, the 2-generates 37.5 percent of all repair flaws percent blend factor for repair welds will be between the ID and 3/8T. Thus, FAVOR increased in future analyses to 2.3 percent underestimates the 43-percent value based (i.e., 2%43/37.5) (see Appendix A).

on the data given above.

1 0.9 0.8 Cummulative distribution ( faction) 0.7 0.6 0.5 Random distribution of flaw locations 0.4 0.3 0.2 0.1 0

0.00 0.20 0.40 0.60 0.80 1.00 Depth of Flaw from Cavity Surface (fraction)

Weld Repair Mouth Weld Repair Root Figure 2.2. Distribution of repair flaws in any weld repair cavity 100%

NUREG/CR-6471, Vol.2 Percent of Repair 80% Repair made from ID (26 observations)

Repair made from OD (26 observations)

Combined (52 Observations)

Expon. (Combined (52 Observations))

60%

Excavations Extending to y = 1.1066e -0.558x R2 = 0.9773 40%

this Depth or Greater 20%

0%

0 1 2 3 4 5 6 7 8 Depth of Repair Excavation [inches]

Figure 2.3. Distribution of weld repair flaws through the vessel wall thickness 6

2.5 Distribution of Underclad Flaws in 2.6 Embrittlement Trend Curve Forgings 2.6.1 Review Finding 2.5.1 Review Finding FAVOR uses an embrittlement trend curve to Very shallow flaws were created on some forged estimate how transition temperature shift vessels by underclad cracking that occurred depends on both composition (copper, nickel, during or following the cladding process. What phosphorus) and exposure (flux, fluence, time) is the effect of underclad flaws on TWCF, and variables for the steels used in the beltline region how does this affect RT-based PTS screening of operating PWRs. Version 04.1 of FAVOR limits for ring-forged vessels? uses an embrittlement trend curve (Kirk 03) that differs from both the trend curve recommended 2.5.2 Model Change by the American Society for Testing and Materials (ASTM) (ASTM E900) as well as Dr. Fredric Simonen of PNNL performed a from the trend curve most recently literature review to establish a distribution for recommended by NRC contractors (Eason 07).

underclad flaws suitable for use within the Should the staff consider any revisions to the probabilistic fracture mechanics code FAVOR. trend curve adopted by FAVOR?

Appendix B is a report summarizing Dr. Simonens findings. When unfavorable 2.6.2 Model Change welding conditions (high-heat inputs) and material conditions (chemistries having high Both the embrittlement trend curve adopted in proportions of impurity elements) coincide, FAVOR Version 04.1 (Kirk 03) and the ASTM underclad cracks can appear in forgings. When E900 trend curve (ASTM E900) are based on an underclad cracks appear they do so as dense analysis of surveillance data available through arrays (typical intercrack spacing is 1 or 2 approximately 2001, whereas the trend curve millimeters). They will have depths on the order detailed in (Eason 07) features an analysis of all of 1 millimeter, but in rare cases can extend into surveillance data available through the ferritic steel of the RPV wall by as much as approximately 2004. For this reason, FAVOR 6 millimeters. Underclad cracks are oriented Version 06.1 will be based on the trend curve in perpendicular to the direction in which the weld (Eason 07), as detailed in the change cladding was deposited, which is to say axially specification (see Appendix A). A description in the vessel. While the conditions under which of the basis for this relationship is available underclad cracks form are not believed to typify elsewhere (Eason 07).

those characteristic of most or all of the 21 forged PWRs now in service, the staff was not Subsequent to the development of FAVOR 06.1, able to establish a criteria that could in accordance with the change specification in differentiate, with a high degree of confidence, Appendix A, Eason developed an alternative those vessels that are believed to be prone to embrittlement trend curve of a slightly underclad cracking from those that are not. For simplified form (Eason 07). The results reported this reason, the staff decided to perform in Appendix C demonstrate that the effect of this sensitivity studies at different levels of alternative trend curve on the TWCF values embrittlement using FAVOR, along with estimated by FAVOR is insignificant.

Dr. Simonens underclad flaw distribution on forged vessels. In these analyses the staff 2.7 LOCA Break Frequencies assumed that underclad cracks exist. Section 3.4 of this report summarizes the results of these 2.7.1 Review Finding sensitivity studies and uses these results to develop RT-based screening limits for forged Recently the NRC staff conducted an expert vessels. elicitation to update the LOCA break 7

frequencies needed as part of a risk-informed revision to 10 CFR 50.46, Acceptance Criteria 2.9.2 Model Change for Emergency Core Cooling Systems for Light-Water Nuclear Power Reactors. These The NRC staff believes that the FAVOR 06.1 frequencies were documented in NUREG-1829 model should incorporate these new results. As (Tregoning 05). Have the calculations detailed in Appendix A, FAVOR 06.1 adopts the documented by the various reports listed in latest findings on the upper-shelf fracture Section 4.1 used these most recent estimates of toughness model described in (EricksonKirk LOCA break frequencies? 06a) and (EricksonKirk 06b).

2.7.2 Model Change 2.10 Demonstration That the Flaws That Contribute to TWCF are The FAVOR 04.1 results used values for LOCA break frequencies that pre-dated the (Tregoning Detectable by NDE Performed

05) document. The FAVOR 06.1 results, which to ASME SC VIII Supplement 4 are detailed in Chapter 3, make use of the LOCA Requirements break frequencies from the (Tregoning 05) document. 2.10.1 Review Finding 2.8 Temperature-Dependent Thermal NUREG-1806 (EricksonKirk-Sum) indicates Elastic Properties that a low density of flaws is one major factor in keeping the total risk associated with PTS low.

2.8.1 Review Finding The state of knowledge of the flaw densities in the 70 individual PWR plants now in service is FAVOR 04.1 adopts temperature-invariant based primarily on detailed destructive thermal elastic properties despite well- examinations of a small number of welds and documented evidence, as reflected by American plates from four vessels (but mostly from two Society of Mechanical Engineers (ASME) vessels), coupled with expert elicitation and codes, that these properties depend on physical modeling. Another potential source of temperature. Is the FAVOR 04.1 model information on flaw density is the in-service appropriate? inspections performed at 10-year intervals on each operating vessel. It would be very helpful if those inspections could provide evidence to 2.8.2 Model Change support the assumptions in the current analysis.

Specifically, it is important to know the The NRC staff does not believe that the significance of a flaw to the FAVOR analysis FAVOR 04.1 model is appropriate.

(based on its size and through-wall location) as Temperature-dependent thermal elastic well as the probability of detection for those properties have been adopted in FAVOR 06.1, flaws found, based on the FAVOR analysis, to as detailed in Appendix A and in (Williams 07).

be risk significant.

2.9 Upper-Shelf Fracture Toughness 2.10.2 Reply Model Flaw Depths Important for PTS 2.9.1 Review Finding Figure 2.4, Figure 2.5, and Figure 2.6 originally Since FAVOR 04.1 was finalized, further work appeared in NUREG-1808 (EricksonKirk-SS) has been published on an upper-shelf fracture as Figures 4-3, 4-4, and 4-5, respectively.

toughness model for ferritic steels (EricksonKirk Collectively these figures demonstrate that the 06a; EricksonKirk 06b). Should the FAVOR flaws that contribute to PTS risk are (1) all 06.1 model incorporate these new results?

8

located within approximately 1 inch of the accomplish this. Subsequently, the NRC has vessel inner diameter and (2) almost invariably required the implementation of Appendix VIII, have a 2a (or through-wall extent) dimension of leading to the availability of improved data to 0.5 inch or less. document the effectiveness of the NDE for the flaws important to PTS. Supplement 4 of To examine the flaw size/location combinations Appendix VIII covers the clad-to-base metal that contribute to PTS risk in further detail, the region up to a depth of 1 inch or 10 percent of staff performed a series of deterministic analyses the vessel wall thickness, whichever is larger.

by locating flaws of various sizes axially in the Thus, Supplement 4 or Appendix VIII of the Palisades RPV. Analyses were performed of ASME Code addresses the flaw locations and both a repressurization transient (#65) and of a sizes of interest for PTS.

large-diameter primary-side pipe break transient

(#62) to address the two types of loadings that ID OD collectively are responsible for more than 90 percent of the PTS risk. Additionally, the staff tWALL performed analyses for embrittlement conditions ranging from those characteristic of current service to those that would be needed to produce a TWCF equal to the 1x10-6/ry limit. The results 2c of these analyses at 60 effective full-power years (EFPY) and at an embrittlement level characteristic of the 1x10-6/ry limit appear in Figure 2.7. Consistent with the conclusions L 2a based on the probabilistic analyses, these results also indicate that small flaws located close to the tCLAD ID will dominate PTS risk.

Figure 2.4. Flaw dimension and position Probability of Detection descriptors adopted in FAVOR Historically, the inspection of PWR vessels has been conducted from the ID. Before 1986, the

% of Flaws Predicted to Initiate 8

inspections were conducted with ultrasonic Beaver Valley at Ext-Bb testing that was quite unreliable for flaw sizes Palisades at Ext-Pb and locations important to PTS. Thus, these 6 examinations would be of little value when assessing the risk of vessel failure resulting from PTS. 4 In 1986, the ASME Code,Section XI, began to 2 require that the inspection of the vessel must be conducted using a technique that was effective for the ID near-surface zone of the vessel. This 0 new requirement was based on results from the 0.000 0.125 0.250 0.375 Program for Inspection of Steel Components Distance of Inner Crack Tip (PISC). PISC II showed that inspection from Clad/Base Interface, sensitivity needed to be increased from 50-percent distance amplitude correction (DAC) to L /twall 20-percent DAC and a special technique is Figure 2.5. Distribution of through-wall position required for this ID near-surface zone using the of cracks that initiate increased sensitivity. PISC II showed that a technique using 70 dual-L wave probes would 9

Figure 2.6. Flaw depths that contribute to crack initiation probability in Beaver Valley Unit 1 when subjected to (left) medium- and large-diameter pipe break transients and (right) stuck-open valve transients at two different embrittlement levels In a probabilistic analysis, almost all of the TWCF comes from this shaded region.

2.5 F limit ID at 10 -6 Re-pressurization Y OD transient FP

/ry TW 60E tWALL 2.0 a t C

L [inches]

1.5 2c CF limit at 10 /ry TW

-6 Large diameter 1.0 pipe break transient L 2a CPI 0 at 60 EFPY tCLAD 0.5 CPI > 0 0.0 0.0 0.5 1.0 1.5 2.0 2a [inches]

(note: c=6a)

Note: Each curve in the figure above divides the graph into two regions:

The region above each curve represents combinations of flaw location (L) and flaw size (2a) that cannot produce crack initiation for the embrittlement and loading conditions represented by the curve.

The region below each curve represents combinations of flaw location (L) and flaw size (2a) that produce some finite probability of crack initiation for the embrittlement and loading conditions represented by the curve.

Figure 2.7. Analysis of Palisades transients #65 (repressurization transient) and #62 (large-diameter primary-side pipe break transient) to illustrate what combinations of flaw size and location lead to non-zero conditional probabilities of crack initiation 10

In 2002, Becker documented the performance of For the foreseeable future (i.e., out to 60 inspectors that have gone through the years of operation) if an inspection were to Supplement 4 qualification process (Becker 02). be performed that inspection should focus Beckers paper describes the findings of the U.S. on detection of flaws having a through-wall Performance Demonstration Initiative (PDI), extent of 0.3-0.4 inches and larger because which has manufactured 20 RPV mockups that, these are the flaws that make the greatest in total, contain in excess of 300 flaws. Since its contribution to the non-zero probability of inception in 1994, the PDI has performed over crack initiation from PTS loading.

10 separate automated demonstrations as well as Performing RPV inspections in accordance numerous manual qualifications. The welds with ASME Code, Appendix VIII, examined include both shell welds and the more Supplement 4 requirements results in a 99-difficult to examine nozzle-to-shell and nozzle- percent or greater probability that such flaws inner-radius welds. Figure 2.8, digitized from can be detected.

Figure 2 of Beckers paper, shows the probability of detection as a function of crack If a vessel were to be embrittled to the point depth (here called through-wall extent) that it challenged the 1x10-6/ry limit on considering pooled data from both manual and TWCF and if an inspection were to be automated inspection processes. This performed that inspection should focus on probability of detection (POD) curve is based on detection of flaws having a through-wall results of passed plus failed candidates, which is extent of approximately 0.1 inch and larger standard industry practice. Inclusion of passed because these are the flaws that make the candidates only when deriving a POD curve is greatest contribution to the non-zero regarded as being overly optimistic; the probability of crack initiation from PTS inclusion of passed plus failed candidates is loading. Performing RPV inspections in taken to provide a lower-bound estimate of accordance with ASME Code, Appendix expected inspection performance. VIII, Supplement 4 requirements results in an 80-percent or greater probability that Summary such flaws can be detected.

Combining the information on POD from Figure Based on the information presented in this 2.8 with the information on the flaw sizes that section it seems highly likely that the flaw sizes are needed to produce non-zero crack initiation of importance to PTS can be detected if probabilities (Figure 2.5 through Figure 2.7) inspections are performed in accordance with leads to the following conclusions: ASME Code, Appendix VIII, Supplement 4 requirements.

100%

Probability of 80%

60%

Detection for ID Exam 40%

No samples had flaws with TWE < 0.1-in. POD curve is extrapolated below 0.1-in.

20% [Becker 2002]

0%

0.0 0.2 0.4 0.6 0.8 1.0 Through-Wall Extent [in]

Figure 2.8. Probability of detection curve (Becker 02) 11

12 Chapter 3 - PTS Screening Limits 3.1 Overview results. The first option places a limit on the estimated TWCF value while the second On the basis of the findings of the internal option places limits on the RT values reviews that Chapter 2 detailed, the NRC associated with the various steels from developed a change specification for FAVOR which the reactor beltline is constructed.

(see Appendix A). FAVOR Version 04.1, which These options are completely equivalent, as was used to develop the TWCF estimates they both derive directly from the results reported in NUREG-1806 (EricksonKirk-Sum), presented in Sections 3.3 and 3.4.

was revised in accordance with this specification to produce FAVOR Version 06.1 (Williams 07; 3.2 Use of Plant-Specific Results to Dickson 07a). Additionally, a special version of Develop Generic RT-Based FAVOR 06.1 was developed to run on the Oak Screening Limits Ridge National Laboratory super-computer cluster to facilitate efficient simulation of large This section first justifies the approach of using populations of underclad cracks. Detailed the results of plant-specific probabilistic results from the FAVOR Version 06.1 analyses analyses to develop RT-based screening limits of plate-welded and ring-forged vessels can be applicable to all U.S. PWRs. The section then found in (Dickson 07b). discusses the use of an RT approach to correlating the TWCF that occurs as a result of Information in this chapter is organized as various flaw populations. The section concludes follows: with a discussion of the need for margin when using the proposed approach.

Section 3.2 reviews the rationale first put forward in NUREG-1806 for using plant- 3.2.1 Justification of Approach specific TWCF versus RT results to develop RT-based screening limits useful for Chapter 8 of NUREG-1806 (EricksonKirk-assessing the PTS risk of any PWR currently Sum) estimates the variation of TWCF with operating in the United States. embrittlement level in the three study plants (Oconee Unit 1, Beaver Valley Unit 1, and Section 3.3 examines the FAVOR 06.1 Palisades). NUREG-1806 reported the results for Beaver Valley Unit 1, Oconee following major findings:

Unit 1, and Palisades (Dickson 07b).

Similarity to the FAVOR 04.1 results Only the most severe primary-side transients reported in NUREG-1806 is assessed, and (medium- to large-diameter pipe breaks and the FAVOR 06.1 results are used to stuck-open valves that later reclose) establish relationships between TWCF and contribute in any significant manner to the RT-metrics for plate-welded PWRs risk of vessel failure from PTS. At lower currently in operation. embrittlement levels stuck-open valves are the dominant risk contributors. However, at Section 3.4 examines the FAVOR results for the embrittlement levels needed to produce ring-forged vessels (Dickson 07b). These an estimated TWCF equal to the 10-6/ry results are used to establish relationships limit, medium- to large-diameter pipe breaks between TWCF and RT-metrics for ring- dominate.

forged PWRs currently in operation.

Severe secondary-side transients (e.g., a Section 3.5 combines the information in break of the main steamline) do not Sections 3.3 and 3.4 to produce two options contribute significantly to the risk of vessel for regulatory implementation of these failure from PTS. These transients have 13

extremely rapid initial cooling rates, which to-plant differences arising from different generate high thermal stresses close to the human responses is expected. (See vessel inner diameter. Nevertheless, the NUREG-1806, Section 8.5.2 for details.)

minimum temperature in the primary system that occurs during these transients, the Stuck-Open Primary-Side Valves: For this boiling point of water, is not low enough to class of transients to be risk significant two produce a significant risk of brittle fracture criteria must be met(1) the valve must in the RPV steel. Additionally, a remain stuck open long enough that the conservatism of the TH models adopted for temperature of the RCS inventory the main steamline break (MSLB) (i.e., not approaches that of the injection water and accounting for the fact that pressurization of (2) once the valve recloses the primary containment caused by the break will raise system must repressurize to the safety valve the boiling point of water by 30-40 F setpoint. Both of these parameters (injection above that assumed, 212 F, in the TH water temperature and safety valve setpoint analysis) suggests strongly that reported pressure) are input to the RELAP analysis TWCF values for this transient class and so are not influenced significantly by overestimate those that can actually occur. RELAP modeling uncertainties. Moreover, neither parameter varies much within the Collectively, these findings demonstrate that population of currently operating PWRs.

only the most severe transients contribute The modeling of this transient class reflects significantly to the estimated risk of RPV failure credible operator actions. These actions do caused by PTS. Information presented in alter some details of the predicted pressure NUREG-1806 demonstrates that the nature of and temperature transients and do vary these transient classes is not expected to vary somewhat based on the RPV vendor because greatly among the population of currently training programs are vendor specific.

operating PWRs. This information is Nevertheless, the analysis demonstrated that summarized below: most differences caused by operator actions do not appreciably influence the risk Medium- to Large-Diameter Primary-Side significance of the transient. Operator Pipe Breaks: To be risk significant the actions only matter if repressurization of the break diameter needs to exceed primary system can be prevented after valve approximately 5 inches. The similarity of reclosure. If the operator throttles injection PWR vessel sizes in the operating U.S. within 1 minute of being allowed, and if the reactor fleet suggests that different plants transient was initiated under HZP conditions will have nominally equivalent reactor then repressurization can be prevented.

coolant system (RCS) cooling rates for these Because HZP accounts for only a small large break diameters. Additionally, the percentage of the plants operating time, the cooling rate of the RCS inventory for these total effect of the modeled operator actions large breaks exceeds that achievable by the on the estimated risk significance of these RPV steel, which is limited by its thermal transients is small. (See NUREG-1806, conductivity of the vessel steel and does not Section 8.5.3 for details.)

vary from vessel to vessel because it is a physical property of the material. Main Steamline Breaks: As discussed Consequently, any small plant-to-plant earlier, even though these transients produce variability that may exist in RCS inventory an extremely rapid initial cooling rate of the cooling rate cannot be transmitted to the RCS inventory (as a result of the large break cooling rate of the RPV steel, which controls area) the minimum temperature of the RCS the thermal stresses in the RPV wall. The (the boiling point of water) is generally high only possible operator action in response to enough to ensure a high level of fracture such a large break is to maximize injection toughness in the vessel wall, thereby flow to keep the core covered, so no plant- preventing MSLB transients from 14

contributing significantly to the total TWCF As discussed in Section 8.4 of NUREG-1806, to estimated for a plant. The size of the main correlate and/or predict resistance of an RPV to steamline is sufficiently large that the fracture, information concerning the fracture cooling rate of the RPV wall is limited by resistance of the materials in the vessel at the the thermal conductivity of the vessel steel, location of the flaws in the vessel is needed. RT which does not vary from plant to plant. In values characterize the resistance of a ferritic the rare instance that through-wall cracking steel to cleavage crack initiation and arrest and does arise from an MSLB transient, it will to ductile crack initiation (EricksonKirk-PFM).

occur within 10-15 minutes after transient NUREG-1806 proposed both weighted and initiation, long before any operator actions maximum RT metrics. Weighted RT metrics can credibly be expected to occur, so plant- accounted for differences in weld length and specific operator action differences cannot plate volume between different plants, while be expected to alter the TWCF associated maximum RT metrics did not. However, with this transient class. (See NUREG- because of the similarities in the size of all 1806, Section 8.5.4 for details.) domestic PWRs, the weighted RT metrics did not provide significantly better correlations with With one small exception, the generalization the TWCF data than did the maximum RT study, in which the plant characteristics that metrics. Furthermore, maximum RT metrics can can influence PTS severity of five additional be estimated for all operating PWRs based high embrittlement plants were investigated, mostly on information currently contained validated these expectations. (See (Whitehead- within the NRCs RVID database (RVID2)

Gen) and Section 9.1 of NUREG-1806 for while weighted RT metrics require additional details.) The recommended PTS screening information from plant construction drawings.

limits presented in Section 3.5 account for this While this information is available, it is not exception. currently compiled for all plants in a single location. For these reasons, this report restricts In summary, the NRCs study demonstrates that its attention to maximum RT metrics.

risk-significant PTS transients do not have any Formulae for the three maximum RT metrics appreciable plant-specific differences within the proposed in NUREG-1806 (RTMAX-AW, RTMAX-population of PWRs currently operating in the PL, and RTMAX-CW) are repeated below (the United States. These findings motivate the algebraic expression of these formulae have development of generic screening limits that can been modified slightly from the form reported in be applied to all operating PWRs.

NUREG-1806 to improve clarity):

3.2.2 Use of Reference Temperatures to Correlate TWCF RTMAX-AW characterizes the resistance of the RPV to fracture initiating from flaws found along the axial weld fusion lines. It is evaluated using the following formula for each axial weld fusion line within the beltline region of the vessel (the part of the formula inside the

{}). The value of RTMAX-AW assigned to the vessel is the highest of the reference temperature values associated with any individual axial weld fusion line. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld and plate evaluated is also needed.

n AWFL MAX MAX AWFL(i)

RTNDT adj aw ( i )

T30adj aw( i ) t FL ,

(u )

Eq. 3-1 RTMAX AW i 1 adj pl ( i )

RTNDT ( u ) T30 adj pl ( i )

t FL where 15

nAWFL is the number of axial weld fusion lines in the beltline region of the vessel, i is a counter that ranges from 1 to nAWFL, tFL is the maximum fluence occurring on the vessel ID along a particular axial weld fusion line, adj aw ( i )

RTNDT (u ) is the unirradiated RTNDT of the weld adjacent to the ith axial weld fusion line, adj pl ( i )

RT NDT ( u ) is the unirradiated RTNDT of the plate adjacent to the ith axial weld fusion line, adj aw ( i )

T 30 is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the weld adjacent to the ith axial weld fusion line, and T30adj pl ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the plate adjacent to the ith axial weld fusion line.

RTMAX-PL characterizes the resistance of the RPV to fracture initiating from flaws in plates that are not associated with welds. It is evaluated using the following formula for each plate within the beltline region of the vessel. The value of RTMAX-PL assigned to the vessel is the highest of the reference temperature values associated with any individual plate. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld and plate evaluated is also needed.

n PL Eq. 3-2 RTMAX PL MAX RTNDT ( u ) T30 PL ( i ) PL ( i )

t MAX PL ( i )

i 1 where nPL is the number of plates in the beltline region of the vessel, i is a counter that ranges from 1 to nPL, t MAX PL (i )

is the maximum fluence occurring over the vessel ID occupied by a particular plate, PL ( i )

RTNDT (u ) is the unirradiated RTNDT of a particular plate, and T30PL (i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to t MAXPL (i )

of a particular plate.

RTMAX-CW characterizes the resistance of the RPV to fracture initiating from flaws found along the circumferential weld fusion lines. It is evaluated using the following formula for each circumferential weld fusion line within the beltline region of the vessel (the part of the formula inside the {}). Then the value of RTMAX-CW assigned to the vessel is the highest of the reference temperature values associated with any individual circumferential weld fusion line. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld, plate, and forging evaluated is also needed.

16

RTNDTadj cw ( i )

T30adj cw(i ) t FL ,

(u )

MAX MAX CWFL(i) RTNDT T30adj pl (i ) t FL ,

n CWFL adj pl ( i )

Eq. 3-3 RTMAXCW (u )

i 1 RT adj fo ( i ) T adj fo ( i ) t NDT ( u ) 30 FL where nCWFL is the number of circumferential weld fusion lines in the beltline region of the vessel, i is a counter that ranges from 1 to nCWFL, tFL is the maximum fluence occurring on the vessel ID along a particular circumferential weld fusion line, adj cw ( i )

RTNDT (u ) is the unirradiated RTNDT of the weld adjacent to the ith circumferential weld fusion line, adj pl ( i )

RT NDT ( u ) is the unirradiated RTNDT of the plate adjacent to the ith circumferential weld fusion line (if there is no adjacent plate this term is ignored),

adj fo ( i )

RTNDT (u ) is the unirradiated RTNDT of the forging adjacent to the ith circumferential weld fusion line (if there is no adjacent forging this term is ignored),

T30adj cw(i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the weld adjacent to the ith circumferential weld fusion line, T30adj pl ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the plate adjacent to the ith axial weld fusion line(if there is no adjacent plate this term is ignored), and T30adj fo (i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the forging adjacent to the ith axial weld fusion line(if there is no adjacent forging this term is ignored).

The T30 values in Eq. 3-1 to Eq. 3-3 are determined as follows:

Eq. 3-4 T30 MD CRP MD A1 0.001718TRCS 1 6.130PMn 2.471 te 1.100 CRP B 1 3.769 Ni 1.191 RCS T f Cu e , P g Cu e , Ni, te 543.1

The results reported in Appendix C demonstrate that the alternative form of this relationship presented in Chapter 7 of (Eason 07) has no significant effect on the TWCF values estimated by FAVOR.

17

1.140 x10 7 for forgings A 1.561x10 7 for plates 1.417 x10 7 for welds 102.3 for forgings 102.5 for plates in non - CE manufactured vessels B

135.2 for plates in CE manufactured vessels 155.0 for welds t for 4.3925 1010 te 4.3925 10 10 0.2595 10 t

for 4.3925 10 Note: Flux () is estimated by dividing fluence (t) by the time (in seconds) that the reactor has been in operation.

log t 1.1390Cue 0.4483Ni 18.12025 g Cue , Ni, te tanh 10 e 1 1 2 2 0.6287 0 for Cu 0.072 f Cue , P Cue 0.072 for Cu 0.072 and P 0.008 0.6679 Cu 0.072 1.359( P - 0.008)0.6679 for Cu 0.072 and P 0.008 e

0 for Cu 0.072 wt%

Cue Cu for Cu 0.072 wt%

0.370 for Ni 0.5 wt%

Max(Cue ) 0.2435 for 0.5 Ni 0.75 wt%

0.301 for Ni 0.75 wt% (all welds with L1092 flux)

NUREG-1806 proposes the use of these three The degree of irradiation damage suffered different RTs in recognition of the fact that the by the material at the flaw tips varies with probability of vessel fracture initiating from location in the vessel because of differences different flaw populations varies considerably in chemistry and fluence.

as a result of the following known factors:

These differences indicate that it is impossible Different regions of the vessel have flaw for a single RT value to represent accurately the populations that differ in size (weld flaws resistance of the RPV to fracture in the general are considerably larger than plate flaws),

case. Indeed, this is precisely the liability density (weld flaws are more numerous than associated with the RT value currently adopted plate flaws), and orientation (axial and by 10 CFR 50.61, the RTPTS. The RTPTS, as circumferential welds have flaws of defined in 10 CFR 50.61, is the maximum corresponding orientations, whereas RTNDT of any region in the vessel (a region is an plate flaws may be either axial or axial weld, a circumferential weld, a plate, or a circumferential). The driving force to forging) evaluated at the peak fluence occurring fracture depends both on flaw size and in that region. Consequently, the RTPTS value orientation, so different vessel regions currently assigned to a vessel may only experience different fracture-driving forces.

coincidentally correspond to the toughness 18

properties of the material region responsible for estimated relative to the current 10 CFR 50.61 the bulk of the TWCF, as illustrated by the procedure, which uses a single RT-metric following examples: (RTPTS).

Out of 71 operating PWRs, 14 have their RTPTS values established based on 3.3 Plate-Welded Plants circumferential weld properties (RVID2).

However, the results in NUREG-1806 show 3.3.1 FAVOR 06.1 Results that the probability of a vessel failing as a consequence of a crack in a circumferential Detailed results from the FAVOR 06.1 analyses weld is extremely remote because of the of Oconee Unit 1, Beaver Valley Unit 1, and lack of through-wall fracture driving force Palisades can be found in a separate report by associated with circumferentially oriented (Dickson 07b). Table 3.1 includes a summary of cracks. For these 14 vessels, the RTPTS these results, which have been reviewed and value is unrelated to any material that has found to be consistent in most respects with the any significant chance of causing vessel findings presented in NUREG-1806. This failure. section highlights two key findings that support the use of these results to develop RT-based Out of 71 operating PWRs, 32 have their screening limits applicable to all plate-welded RTPTS values established based on plate plants.

properties (RVID2). Certainly, plate properties influence vessel failure Characteristics of TWCF Distributions probability; however, the 10 CFR 50.61 practice of evaluating RTPTS at the peak Section 8.3.2 of NUREG-1806 reported that the fluence occurring in the plate is likely to TWCF distributions calculated previously by estimate a toughness value that cannot be FAVOR Version 04.1 were heavily skewed associated with any large flaws because the towards zero or very low values, and that this location of the peak fluence may not skewness occurs as a natural consequence of (1) correspond to an axial weld fusion line. the rarity of multiple unfavorable factors While the RTPTS value for these 32 vessels is combining to produce a high failure probability based on a material that significantly and (2) the fact that the distributions of both contributes to the vessel failure probability, cleavage crack initiation and cleavage crack it is likely that RTPTS has been overestimated arrest fracture toughness have finite lower (perhaps significantly so) because the bounds. Figure 3.1 demonstrates that the fluence assumed in the RTPTS calculation changes made to the FAVOR code (see does not correspond to the fluence at a likely Appendix A) have not qualitatively altered this flaw location. situation. However, as illustrated in Figure 3.2, Out of 71 operating PWRs, 15 have their the percentile of the TWCF distribution RTPTS values established based on axial corresponding to the mean TWCF value is lower weld properties (RVID2). It is only for for the FAVOR 06.1 results than it was for the these vessels that the RTPTS value is clearly FAVOR 04.1 results. The mean TWCF values associated with a material region that estimated using FAVOR 04.1 corresponded to contributes significantly to the vessel failure between the 90th and 99th percentile, depending probability and is evaluated at a fluence that on the level of embrittlement. Conversely, the is clearly associated with a potential location mean TWCF values estimated using FAVOR of large flaws. 06.1 corresponded to between the 80th and 99th percentile. The percentile associated with the For these reasons, the use of the three RT- mean TWCF has been reduced in FAVOR 06.1 metrics proposed here (RTMAX-AW, RTMAX-PL, and results for the following two reasons:

RTMAX-CW) is expected to increase the accuracy with which the TWCF in a vessel can be 19

(1) The change in the data basis for the RTNDT underestimated. Consequently, the following epistemic uncertainty correction (see Task sections of this report use 95th percentile TWCF 1.1 in the FAVOR change specification in values in the TWCF versus RT regressions. Use Appendix A) and the change in the of 95th percentile values makes the probability embrittlement trend curve (see Task 1.5 in that the TWCF is underestimated acceptably the FAVOR change specification in small (1 chance out of 20).

Appendix A) have increased the embrittlement level associated with each 35%

EFPY analyzed. This increase in Percent of Simulated Vessels 32 EFPY 30%

embrittlement reduces the TWCF percentile Ext-B associated with the mean along the same 25%

trend line established by the FAVOR 04.1 20%

analyses (see Figure 3.2). Indeed, the percentile associated with the mean should 15%

reduce with increased embrittlement 10%

because, for more embrittled materials, fewer zero failure probability vessels are 5%

simulated, leading to a less skewed 0%

distribution of TWCF.

zero

<= E-16 E-15 E-14 E-13 E-12 E-11 E-10 E-9 E-8 E-7 E-6 E-5 E-4 (2) The change in the RTNDT epistemic TWCF Value uncertainty sampling procedure (in FAVOR 04.1, the RTNDT epistemic uncertainty was Figure 3.1. TWCF distributions for Beaver sampled inside the flaw loop; in FAVOR Valley Unit 1 estimated for 32 06.1, this sampling was moved outside of EFPY and for a much higher level the flaw loopsee Task 1.3 in the FAVOR of embrittlement (Ext-B). At 32 EFPY the height of the zero bar change specification in Appendix A) has is 62 percent.

pushed more of the density of the TWCF distributions to occur in their upper tails, 100 thereby broadening them. This change was Percentile of Mean TWCF Value motivated by the observation that the 90 FAVOR 04.1 procedure simulated an 80 uncertainty in RTNDT for an individual 70 major-region of a simulated vessel (a major- 60 region is an individual weld, plate, or 50 Shaded Symbols: FAVOR 04.1 (NUREG-1806) forging) having a total range in excess of 40 Solid Symbols: FAVOR 06.1 150 F. This range is much larger than that (This Report) 30 measured in laboratory tests, so FAVOR Oconee 20 was modified to bring its simulations into Beaver Valley better accord with observations. 10 Palisades 0

NUREG-1806 uses mean TWCF values in the 100 200 300 400 TWCF versus RT regressions because the Maximum RT NDT Along Axial Weld o

percentile associated with the mean exceeded 90 Fusion Line [ F]

percent in all cases (see Figure 3.2). As explained earlier, this is no longer the case, and Figure 3.2. The percentile of the TWCF it is not appropriate to use 80th percentile distribution corresponding to mean TWCF values in the TWCF versus RT TWCF values at various levels of regressions because doing so would create too embrittlement high a chance (1 chance out of 5) that the TWCF associated with a particular RT value is 20

Dominant Transients RTMAX-AW, RTMAX-PL, and RTMAX-CW) and the TWCF resulting from their three respective flaw As reported in Section 8.5 of NUREG-1806 and populationsaxial fusion line flaws in axial summarized in Section 3.2.1 of this report, only welds, axial and circumferential flaws in plates, the most severe transients make any significant and circumferential flaws in circumferential contribution to the total estimated risk of welds. The following trends, demonstrated by through-wall cracking from PTS. Examination the data in this figure agree well with those of the results in (Dickson 07b) shows that the reported previously in Section 11.3.2 of risk-dominant transients listed in Tables 8.7, 8.8, NUREG-1806:

and 8.9 of NUREG-1806 also dominate the risk in the current (i.e., FAVOR 06.1) analyses. The TWCF produced by axial weld flaws dominates the PTS risk of plate-welded Figure 3.3 shows the dependence of the TWCF PWRs.

resulting from the two dominant transient classes (medium- to large-diameter primary-side The TWCF produced by plate flaws makes a pipe breaks, and stuck-open primary valves that more limited contribution to PTS risk than may later reclose) and of MSLBs on do axial weld flaws. This is because the embrittlement level (as quantified by RTMAX- plate flaws, while more numerous than axial AW). The trends in these figures agree well with weld flaws, are considerably smaller.

those reported previously in Section 8.5 of Additionally, half of the plate flaws are NUREG-1806, i.e.: oriented circumferentially and half are oriented axially.

Stuck-open primary-side valves dominate the TWCF at lower embrittlement levels. The TWCF produced by circumferential As embrittlement increases, medium- to flaws is essentially negligible. At the large-diameter primary-side pipe breaks highest RTMAX-CW currently expected for any become the dominant transients. In PWR after 60 years of operation (258 F or combination these transient classes 718R), circumferential weld flaws are constitute 90 percent or more of the total responsible for approximately 0.04 percent TWCF irrespective of embrittlement level. of the 1x10-6/ry TWCF limit proposed in Chapter 10 of NUREG-1806.

MSLBs are responsible for virtually all of the remaining risk of through-wall cracking. The equations of the curves in Figure 3.4 all It should, however, be remembered that the share the same form, which is as follows:

models of MSLBs are intentionally conservative. More accurate modeling of Eq. 3-5 MSLB transients is therefore expected to further reduce their perceived risk TWCF95 xx expm ln RTMAX xx RTTH xx b significance.

In Eq. 3-5, the 95 subscript denotes the 95th percentile; while the xx subscript indicates the None of the other transient classes (small- flaw population (xx is AW for axial weld flaws, diameter primary-side breaks, stuck-open CW for circumferential weld flaws, and PL for secondary valves, feed and bleed, steam plate flaws). The value RTTH-xx is a fitting generator tube rupture) are severe enough to coefficient that permits Eq. 3-5 to have a lower significantly contribute to the total TWCF. vertical asymptote on a semi-log plot. Values of temperature are expressed in absolute degrees Dominant Material Features (Rankine = Fahrenheit + 459.69) to prevent a logarithm from being taken of a negative Figure 3.4 shows the relationship between the number. Values of the best-fit coefficients for three RT metrics described in Section 3.2.2 (i.e.,

21

Table 3.1. Summary of FAVOR 06.1 Results Reported in (Dickson 07b)

TWCF Partitioned by TWCF Partitioned by Transient Class (% of th Flaw Population (% of 95 total TWCF)

RTMAX- RTMAX- RTMAX- MEAN Mean %ile of total TWCF)

Plant

%ile EFPY AW CW PL FCI TWCF Mean Primary Main o o o TWCF Primary Secondary

[ F] [ F] [ F] (/ry) (/ry) TWCF Axial Circ. Stuck- Steam-(/ry) Plates Pipe Stuck-Open Welds Welds Open line Breaks Valves Valves Breaks 1.10E- 1.69E- 3.54E-32 187 224 224 97.4 93.29 0.59 6.12 7.66 92.21 0.09 0.00 07 09 10 5.64E- 6.84E- 1.03E-Beaver 60 204 253 253 93.7 68.15 3.32 28.52 34.45 64.67 0.87 0.00 07 09 08 2.31E- 4.08E- 1.52E-Ext-A 221 284 284 87.2 53.88 5.30 40.83 49.25 47.63 3.08 0.00 06 08 07 1.44E- 5.73E- 2.45E-Ext-B 252 339 339 80.5 21.53 15.05 63.42 70.41 19.58 9.98 0.00 05 07 06 1.25E- 1.13E- 1.16E-32 163 183 75 98.8 100.00 0.00 0.00 0.01 99.99 0.00 0.00 09 09 13 2.84E- 2.15E- 5.35E-Oconee 60 179 198 87 98.2 100.00 0.00 0.00 0.11 99.88 0.00 0.00 09 09 11 3.19E- 2.84E- 4.63E-Ext-A 253 277 158 93.1 99.91 0.07 0.03 9.10 90.89 0.00 0.00 07 08 08 2.77E- 1.40E- 4.39E-Ext-B 298 326 206 86.7 98.96 0.68 0.36 35.65 64.36 0.00 0.00 06 07 07 1.46E- 1.59E- 2.50E-32 222 208 184 93.2 99.99 0.00 0.00 49.64 47.61 1.43 1.25 07 08 08 Palisades 4.64E- 7.85E- 1.96E-60 247 231 209 90.0 100.01 0.00 0.00 59.70 28.52 1.88 9.82 07 08 07 5.21E- 1.74E- 6.12E-Ext-A 322 302 286 81.5 99.84 0.02 0.14 80.60 10.02 2.94 6.29 06 06 06 4.70E- 2.49E- 8.37E-Ext-B 416 393 389 76.9 97.53 0.17 2.33 77.91 4.77 4.67 12.54 05 05 05 22

1.E-04 1.E-04 1.E-04 95th Percentile TWCF Due to Stuck-1.E-05 1.E-05 1.E-05 95th Percentile TWCF Due to Main 95 Percentile TWCF Due to 1.E-06 1.E-06 1.E-06 1.E-07 1.E-07 1.E-07 1.E-08 1.E-08 1.E-08 1.E-09 1.E-09 1.E-09 Primary Side Pipe Breaks 1.E-10 August 2006 1.E-10 August 2006 1.E-10 August 2006 Open Primary Valves Steam Line Breaks FAVOR 06.1 FAVOR 06.1 FAVOR 06.1 1.E-11 1.E-11 1.E-11 th 1.E-12 Beaver 1.E-12 Beaver 1.E-12 Beaver Oconee Oconee Oconee 1.E-13 Palisades 1.E-13 Palisades 1.E-13 Palisades 1.E-14 1.E-14 1.E-14 550 650 750 850 550 650 750 850 550 650 750 850 Max. RT AW [R] Max. RT AW [R] Max. RT AW [R]

Figure 3.3. Dependence of TWCF due to various transient classes on embrittlement as quantified by the parameter RTMAX-AW (curves are hand-drawn to illustrate trends) 23

1.E-03 1.E-03 1.E-03 August 2006 August 2006 August 2006 1.E-04 FAVOR 06.1 1.E-04 FAVOR 06.1 1.E-04 FAVOR 06.1 95 %ile TWCF - Axial Weld Flaws 95 %ile TWCF - Circ Weld Flaws 1.E-05 1.E-05 1.E-05 95 %ile TWCF - Plate Flaws 1.E-06 1.E-06 1.E-06 1.E-07 1.E-07 1.E-07 1.E-08 1.E-08 1.E-08 1.E-09 1.E-09 1.E-09 1.E-10 1.E-10 1.E-10 1.E-11 1.E-11 1.E-11 th Beaver Beaver Beaver th 1.E-12 1.E-12 th 1.E-12 Oconee Oconee Oconee Palisades Palisades Palisades 1.E-13 1.E-13 1.E-13 Fit Fit Fit 1.E-14 1.E-14 1.E-14 550 650 750 850 550 650 750 850 550 650 750 850 Max. RT AW [R] Max. RT PL [R] Max RT CW [R]

Figure 3.4. Relationship between TWCF and RT due to various flaw populations (left: axial weld flaws, center: plate flaws, right: circumferential weld flaws). Eq. 3-5 provides the mathematical form of the fit curves shown here.

24

each flaw population, established by least- only small contributions to the total TWCF95 at squares analysis of the data in Figure 3.4, are as high embrittlement levels.

follows:

Eqs. 3-5 and 3-6 define a relationship between Regressor Variable m b RTTH [R] RTMAX-AW, RTMAX-PL, and RTMAX-CW and the RTMAX-AW 5.5198 -40.542 616 resultant value of TWCF95. Eqs. 3-5 and 3-6 RTMAX-PL 23.737 -162.36 300 RTMAX-CW 9.1363 -65.066 616 may be represented graphically as illustrated in Figure 3.5; the TWCF of the surface shown is 1x10-6. Combinations of RTMAX-AW, RTMAX-PL, Below the value of RTTH-xx the value of and RTMAX-CW that lie inside the surface TWCF95-xx is undefined and should be taken as therefore have TWCF95 values below 1x10-6.

zero.

Eqs. 3-5 and 3-6 can be used, together with 3.3.2 Estimation of TWCF Values and values of RTMAX-AW, RTMAX-PL, and RTMAX-CW RT-Based Limits for Plate-Welded determined from information in the RVID PWRs database, to estimate the TWCF of any plate-welded PWR currently operating in the United Similar to the procedure described in NUREG- States. (See Section 3.3.3 for a necessary 1806, the fits to the TWCF95-xx versus RTMAX-xx modification to these formulae for RPVs having relationships shown in Figure 3.4 and quantified wall thicknesses above 9.5 inches.) These by Eq. 3-5 are combined to develop the calculations (see Section 3.5.1 for details) show following formula that can be used to estimate that no operating PWRs are expected to exceed the TWCF of any currently operating plate- or approach a TWCF of 1x10-6/ry after either 40 welded PWR in the United States: or 60 years of operation.

AW TWCF95 AW The two-dimensional version of the three-Eq. 3-6 TWCF95TOTAL PL TWCF95 PL dimensional graphical representation of Eq. 3-6 provided inFigure 3.5 can be used to develop CW TWCF95CW RT-based screening limits for plate-welded plants. As was done in NUREG-1806, RT limits Here the values of TWCF95-xx are estimated can be established by setting the total TWCF in using Eq. 3-5. The factors are introduced to Eq. 3-6 equal to the reactor vessel failure prevent underestimation of TWCF95 at low frequency acceptance criterion of 1x10-6 embrittlement levels from stuck-open valves on events/year proposed in Chapter 10 of that the primary side that may later reclose (see document. Plate vessels are made up of axial Chapter 9 of NUREG-1806). Values of are welds, plates, and circumferential welds, so in defined as follows: principle, flaws in all of these regions will contribute to the total TWCF. However, as If RTMAX-xx 625R, then = 2.5 revealed by the RT values reported in Table 3.3, If RTMAX-xx 875R, then = 1 the contribution of flaws in circumferential If 625R < RTMAX-xx < 875R then welds to TWCF is negligible. The highest RTMAX-CW anticipated for any currently operating 2.5 1.5 RTMAX xx 625 PWR after 60 years of operation (assuming 250 current operating conditions are maintained) is 258 F. At this embrittlement level flaws in Reduction of as embrittlement (RT) increases circumferential welds would contribute is justified because the generalization study only approximately 0.04 percent of the 1x10-6/ry revealed the potential for the severity of stuck- limit. In view of this very minor contribution of open valve transients to be slightly flaws in circumferential welds to the overall underrepresented, and stuck-open valves make risk, RT-based screening limits for plate-welded plants are developed as follows:

25

(2) Set TWCFTOTAL to the 1x10-6/ry limit

-8 (1) Set TWCF95-CW to 1x10 /ry (this proposed in Chapter 10 of NUREG-1806.

corresponds to an RTMAX-CW value of (3) Solve Eq. 3-6 to establish (RTMAX-AW, 312 F, which far exceeds the highest value RTMAX-PL) pairs that satisfy equality.

expected for any currently operating PWR after 60 years of operation.

Figure 3.5. Graphical representation of Eqs. 3-5 and 3-6. The TWCF of the surface in both diagrams is 1x10-6. The top diagram provides a close-up view of the outermost corner shown in the bottom diagram. (These diagrams are provided for visualization purposes only; they are not a completely accurate representation of Eqs. 3-5 and 3-6 particularly in the very steep regions at the edges of the TWCF = 1x10-6 surface.)

26

As illustrated in Figure 3.6, this procedure 3.3). Comparison of the assessment points for establishes the locus of (RTMAX-AW, RTMAX-PL) the individual plants to the (proposed) 1x10-6 pairs that define the horizontal cross-section of and (current) 5x10-6 limits in Figure 3.6 supports the three-dimensional surface depicted in Figure the following conclusions:

3.5 at an RTMAX-CW value of 312 F. In the region of the graph between the red loci and the The risk of PTS failure is low. Over 80 origin, the TWCF is below the 1x10-6 acceptance percent of operating PWRs have estimated criterion, so these combinations of RTMAX-AW TWCF values below 1x10-8/ry, even after 60 and RTMAX-PL would satisfy the 1x10 6/ry limit years of operation.

on TWCF. In the region of the graph outside of the red loci, the estimated TWCF exceeds the After 40 years of operation the highest risk 1x10-6/ry limit, indicating the need for additional of PTS at any PWR is 2.0x10-7/ry. After 60 analysis or other measures to justify continued years of operation this risk increases to plant operation. For reference, Figure 3.6 shows 4.3x10-7/ry.

loci corresponding to other TWCF values. Of particular interest is the 5x10-6 locus, which The current regulations assume that plants appears in dark green. A 5x10-6 TWCF limit have a TWCF risk of approximately corresponds to that viewed as being acceptable 5x10 6/ry when they are at the 10 CFR 50.61 according to the current version of Regulatory RTPTS screening limits. Contrary to the Guide 1.154, Format and Content of Plant- current situation in which several plants are Specific Pressurized Thermal Shock Safety thought to be within fractional degrees Analysis Reports for Pressurized Water Fahrenheit of these limits, the staffs Reactors, issued January 1987. calculations show that when realistic models are adopted no plant is closer than 53 F at Figure 3.6 also shows assessment points (blue EOL (40 F at end-of-license extension circles and blue triangles), one representing each (EOLE)) from exceeding the 5x10-6/ry limit plate-welded PWR after 40 and 60 years of implicit in RG 1.154.

operation. The coordinates (RTMAX-AW, RTMAX-PL) for each plant were estimated from information in the RVID database (see Table 400 5E-6 400 5E-6 1E-6 1E-6 350 350 1E-7 300 1E-7 300 RTMAX-PL [oF] RTMAX-PL [oF]

1E-8 1E-8 250 250 Plate Welded Plants Plate Welded Plants 200 at 32 EFPY (EOL) o 200 at 48 EFPY (EOLE) 40oF 53 F 17oF 150 30oF 150 100 100 50 50 0 0 0 50 100 150 200 250 300 0 50 100 150 200 250 300 RTMAX-AW [oF] RTMAX-AW [oF]

Figure 3.6. Maximum RT-based screening criterion (1E-6 curve) for plate-welded vessels based on Eq. 3-6 (left: screening criterion relative to currently operating PWRs after 40 years of operation; right: screening criterion relative to currently operating PWRs after 60 years of operation).

27

3.3.3 Modification for Thick-Walled Vessels 50 TWCF / TWCF for 7-7/8-in. Thic Figure 3.7 shows that the vast majority of PWRs 40 currently in service have wall thicknesses between 8 and 9.5 inches. The three vessels analyzed in detail 30 in this study are all in this range and thus represent the vast majority of the operating fleet. As discussed in Section 9.2.2.3 of NUREG-1806, the few PWRs 20 Beaver Valley Vessel at 60 EFP having thicker walls can be expected to experience higher TWCF than the thinner vessels analyzed here 10 (at equivalent embrittlement levels) because of the higher thermal stresses that occur in the thicker vessel 0 walls. Figure 3.8 reproduces the results of a 7 8 9 10 11 12 sensitivity study on wall thickness reported in Vessel Wall Thickness [in]

NUREG-1806. These results show that for PTS-BV9 - 16" Hot Leg Break dominant transients (the 16-inch hot leg break and BV56 - 4" Surge Line Break the stuck-open safety/relief valve) the TWCF in a BV102 - MSLB thick (11 to 11.5 inch) wall vessel will increase by BV126 - Stuck open SRV, re-closes after 100 minutes approximately a factor of 16 over the values presented in this report for vessels having wall Figure 3.8. Effect of vessel wall thickness thicknesses between 8 and 9.5 inches. To account for on the TWCF of various transients in this increased driving force to fracture in thick-walled Beaver Valley (all analyses at 60 EFPY).

vessels the staff recommends that the TWCF This figure originally appeared as Figure estimated by Eq. 3-6 be increased by a factor of 8 for 9.10 in NUREG-1806.

each inch of thickness by which the vessel wall exceeds 9.5 inches. Section 3.5 provides a formula 3.4 Ring-Forged Plants that formally implements this recommendation.

All three of the detailed study plants are plate-30 welded vessels. However, 21 of the currently 25 operating PWRs have beltline regions made of Number of PWRs ring forgings. As such, these vessels have no 20 axial welds. The lack of the large, axially oriented axial flaws from such vessels indicates 15 that they may have much lower values of TWCF than a comparable plate vessel of equivalent 10 embrittlement. However, forgings have a 5 population of embedded flaws that is particular in density and size to their method of 0 manufacture. Additionally, under certain rare 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 conditions forgings may contain underclad cracks that are produced by the deposition of the Vessel Wall Thickness [in] austenitic stainless steel cladding layer. Thus, to Figure 3.7. Distribution of RPV wall thicknesses for investigate the applicability of the results PWRs currently in service (RVID2). reported in Section 3.3 to forged vessels, the This figure originally appeared as staff performed a number of analyses on vessels Figure 9.9 in NUREG-1806. using properties (RTNDT(u), copper, nickel, phosphorus, manganese) and flaw populations appropriate to forgings. Appendices B and D detail the technical basis for the distributions of flaws used in these sensitivity studies.

28

3.4.1 Embedded Flaw Sensitivity Study by irradiation to t MAX FO ( i )

of a particular forging.

Appendix D describes the distribution of embedded forging flaws based on destructive 3.4.2 Underclad Flaw Sensitivity Study examination of an RPV forging (Schuster 02).

These flaws are similar in both size and density By May 1973 the causes of underclad cracking to plate flaws. A sensitivity study based on the were sufficiently well understood for the NRC to embedded forging flaw distribution described in issue Regulatory Guide 1.43, Control of Appendix D was described previously in Stainless Steel Weld Cladding of Low Alloy NUREG-1808 (EricksonKirk-SS) and will not Steel Components (RG 1.43). Vessels be repeated here. This study showed that the fabricated after this date would have had to similarities in flaw size and density between comply with the provisions of Regulatory Guide forgings and plates allow the relationship 1.43 and, therefore, should not be susceptible to between RTMAX-PL and TWCF95 (Eq. 3-6) to be underclad cracking. Vessels fabricated before used for forgings containing embedded flaws. 1973 may have been compliant as well because For forgings the RT metric is defined as follows: the causes of and remediation for underclad cracking were widely known before the issuance RTMAX-FO characterizes the resistance of the of the regulatory guide. Nevertheless, to provide RPV to fracture initiating from flaws in the information needed to support a forgings that are not associated with welds. It comprehensive revision of the PTS Rule the is evaluated using the following formula for NRC staff considered it necessary to establish each forging within the beltline region of the PTS screening limits for vessels containing vessel. The value of RTMAX-FO assigned to the underclad cracking for those situations in which vessel is the highest of the reference compliance with Regulatory Guide 1.43 cannot temperature values associated with any be demonstrated.

individual plate. In evaluating the T30 values in this formula the composition properties As discussed in detail in Appendix B, underclad reported in the RVID database are used for cracks occur as dense arrays of shallow cracks copper, nickel, and phosphorus. An extending into the vessel wall from the clad-to-independent estimate of the manganese basemetal interface to depths that are limited by content of each weld and plate evaluated is the extent of the heat-affected zone also needed. (approximately 0.08 inch (approximately 2 millimeters)). These cracks are oriented Eq. 3-7 normal to the direction of welding for clad n FO RTMAX FO MAX RTNDT ( u ) T30 FO ( i ) FO ( i )

t MAX FO ( i ) deposition, producing axially oriented cracks in i 1 the vessel beltline. They are clustered where the where passes of strip clad contact each other.

nFO is the number of forgings in the Underclad flaws are much more likely to occur beltline region of the vessel, in particular grades of pressure vessel steels that i is a counter that ranges from 1 to have chemical compositions that enhance the nFO, likelihood of cracking. Forging grades such as t MAX FO ( i )

is the maximum fluence occurring A508 are more susceptible than plate materials such as A533. High levels of heat input during over the vessel ID occupied by a the cladding process enhance the likelihood of particular forging, FO ( i )

underclad cracking.

RTNDT (u ) is the unirradiated RTNDT of a particular forging, and The NRC staff could find only limited T FO ( i )

30 is the shift in the Charpy V-Notch information in the literature concerning underclad crack size and density. This lack of 30-foot-pound (ft-lb) energy information on which to base the probabilistic (estimated using Eq. 3-4) produced 29

calculations exists because when underclad underclad cracks can initiate, their failure is cracking was discovered in the late 1960s and almost certain, and additional small increases in early 1970s the understandable focus of the embrittlement will lead to large increases in investigations performed at that time was to TWCF. Because of the steepness of the TWCF prevent the phenomena from occurring versus RTMAX-FO relationship, the staff made no altogether, not to characterize the size and attempt to develop a best fit to the results.

density of the resulting defects. Because of this Instead, the following bounding relationship lack of information, the flaw distribution (which also appears on Figure 3.9) is proposed:

detailed in Appendix B reflects conservative judgments. Eq. 3-8 TWCF95 FO 1.3 10 137 10 0.185RTMAX FO Hypothetical models of forged vessels were Table 3.2. Results of a Sensitivity Study Assessing constructed based on the existing models of the the Effect of Underclad Flaws on the TWCF of Beaver Valley Unit 1 and Palisades vessels. In Ring-Forged Vessels Analysis RTMAX-FO TWCF95 from Underclad these hypothetical forged vessels both the axial ID o

[ F] Flaws welds and the plates in the beltline region were BV 32 187.2 0 (see Note 1) combined and assigned the following properties, BV 60 205.8 0 (see Note 1) which are characteristic of the forging in Sequoyah Unit 1 (RVID2)copper = 0.13 BV 100 225.4 5.67E-11 percent, nickel = 0.76 percent, phosphorus = BV 200 261.2 2.35E-04 0.020 percent, manganese = 0.70 percent, Pal 32 193.0 0 (see Note 1)

RTNDT(u) = 73 F, upper-shelf energy = 72 ft-lbs Pal 60 209.9 0 (see Note 1)

(this forging was selected because it has among Pal200 263.2 3.92E-05 the most embrittlement sensitive properties of Pal 500 332.8 2.08E-04 any forging in the current operating fleet). Note 1: All TWCF was from circumferential weld Using these properties along with the underclad flaws in these analyses flaw distribution described in Appendix B, FAVOR analyses were conducted at a number of 1.E-03 different EFPY values to investigate the 1.E-04 variation of TWCF with embrittlement level.

95 %ile TWCF for Underclad Flaws Because of the extremely high density of 1.E-05 underclad flaws assumed by the Appendix B 1.E-06 flaw distribution, a super-computer cluster was used to perform these FAVOR analyses (see 1.E-07 (Dickson 07b) for a full description of the underclad flaw analysis). Table 3.2 and Figure 1.E-08 3.9 summarize the results of these analyses. The 1.E-09 rate of increase of TWCF with increasing embrittlement (as quantified by RTMAX-FO) 1.E-10 shown in Figure 3.9 for underclad cracks is 1.E-11 much more rapid than shown previously (see TWCF95 FO 1.3 10 137 100.185RTMAX FO Figure 3.4) for plate and weld flaws. The th 1.E-12 steepness of this slope occurs as a direct FAVOR Results consequence of the very high density of 1.E-13 Bound underclad cracks assumed in the analysis (the 1.E-14 mean crack-to-crack spacing is on the order of 550 650 750 850 millimeters). Because of this high density, it is a Max RT FO [R]

virtual certainty that an underclad crack will be simulated to occur in locations of high fluence Figure 3.9. Relationship between TWCF and RT and high stress. Thus, once the level of for forgings having underclad flaws embrittlement has increased to the point that the 30

3.4.3 Modification for Thick-Walled approach in regulations would be fully Vessels consistent with the technical basis information presented in this report, in NUREG-1806, and in As was the case for plate-welded vessels, the the other companion documents listed in effect of increased vessel wall thickness on the Section 4.1.

TWCF in ring-forged vessels must also be quantified. The sensitivity study presented It should be noted that Steps 1 and 2 are previously for plate-welded vessels (see Figure identical in both approaches. Additionally, 3.8) can be used to correct for thickness effects Step 2 uses the embrittlement trend curve from in forgings that have only embedded flaws (no the FAVOR 06.1 change specification underclad cracking) because of the similarity in (Appendix A). Eason has developed an both flaw density and flaw size between alternative embrittlement trend curve of a embedded flaws in forgings and plates. To slightly simplified form (Eason 07). The results investigate the magnitude of an appropriate reported in Appendix C demonstrate that the thickness correction for forgings containing effect of this alternative trend curve on the underclad cracks, the thickness of the TWCF values estimated by FAVOR is hypothetical forging based on the Beaver Valley insignificant. Thus, the equations in vessel was increased to 11 inches and the Appendix C could be adopted instead of the analysis was rerun using subclad cracks. Figure equations presented in Step 2 of Sections 3.5.1 3.10 presents the results of these analyses and and 3.5.2 without the need to change any other compares them with the results presented part of the procedure.

previously for plate-welded vessels (see Figure 3.7) as well as to the thickness correction Results from analyses of forged recommended in Section 3.3.3. This comparison vessels having subclad cracks.

demonstrates that the thickness correction recommended in Section 3.3.3 for plate-welded vessels can also be applied to ring-forged vessels that have underclad cracks.

Thickness correction 3.5 Options for Regulatory recommended in F Implementation of These Section 3.3.3 Results Any future revision of 10 CFR 50.61 must F

include a procedure by which licensees can demonstrate compliance with the 1x10-6/ry TWCF limit based on information that characterizes a particular plant. Sections 3.5.1 and 3.5.2 describe two completely equivalent approaches to achieving this goal, both based on the information presented so far in this chapter.

The first approach places a limit on TWCF of 1x10-6/ry, whereas the second approach places a Figure 3.10. Effect of vessel wall thickness on the limit on the maxima of the various RT values, or TWCF of forgings having underclad combinations thereof, which would produce a flaws compared with results for TWCF value at the limit of 1x10-6/ry. Equations plate-welded vessels (see Figure 3.7) presented elsewhere in this report are repeated in these sections for clarity. Adoption of either 31

3.5.1 Limitation on TWCF Step 1. Establish the plant characterization parameters, which include the following:

RTNDT(u) [ F] The unirradiated value of RTNDT. Needed for each weld, plate, and forging in the beltline region of the RPV.

Cu [weight percent] Copper content. Needed for each weld, plate, and forging in the beltline region of the RPV.

Ni [weight percent] Nickel content. Needed for each weld, plate, and forging in the beltline region of the RPV.

P [weight percent] Phosphorus content. Needed for each weld, plate, and forging in the beltline region of the RPV.

Mn [weight percent] Manganese content. Needed for each weld, plate, and forging in the beltline region of the RPV.

t [seconds] The amount of time the RPV has been in operation.

TRCS [ F] The average temperature of the RCS inventory in the beltline region under normal operating conditions.

tMAX [n/cm2] The maximum fluence on the vessel ID for each plate and forging in the beltline region of the RPV.

tFL [n/cm2/sec.] The maximum fluence occurring along each axial weld and circumferential weld fusion line. This value is needed for each axial weld and circumferential weld fusion line in the beltline region of the RPV.

Twall [inches] The thickness of the RPV wall, including the cladding.

Step 2. Estimate values of RTMAX-AW, RTMAX-PL, RTMAX-FO, and RTMAX-CW using the following formulae and the values of the characterization parameters from Step 1:

RTMAX-AW characterizes the resistance of the RPV to fracture initiating from flaws found along the axial weld fusion lines. It is evaluated using the following formula for each axial weld fusion line within the beltline region of the vessel (the part of the formula inside the {}). The value of RTMAX-AW assigned to the vessel is the highest of the reference temperature values associated with any individual axial weld fusion line. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld and plate evaluated is also needed.

n AWFL RTNDT adj aw ( i )

T30adj aw( i ) t FL ,

MAX MAX AWFL(i) (u )

RTNDT ( u ) T30 t FL RTMAX AW adj pl ( i ) adj pl ( i )

i 1 where nAWFL is the number of axial weld fusion lines in the beltline region of the vessel, i is a counter that ranges from 1 to nAWFL, tFL is the maximum fluence occurring on the vessel ID along a particular axial weld fusion line, adj aw ( i )

RTNDT (u ) is the unirradiated RTNDT of the weld adjacent to the ith axial weld fusion line, 32

adj pl ( i )

RTNDT (u ) is the unirradiated RTNDT of the plate adjacent to the ith axial weld fusion line, adj aw ( i )

T 30 is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the weld adjacent to the ith axial weld fusion line, and T30adj pl (i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the plate adjacent to the ith axial weld fusion line.

RTMAX-PL characterizes the resistance of the RPV to fracture initiating from flaws in plates that are not associated with welds. It is evaluated using the following formula for each plate within the beltline region of the vessel. The value of RTMAX-PL assigned to the vessel is the highest of the reference temperature values associated with any individual plate. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld and plate evaluated is also needed.

t MAX n PL RTMAX PL MAX RTNDT PL ( i )

( u ) T30 PL ( i ) PL ( i )

i 1 where nPL is the number of plates in the beltline region of the vessel, i is a counter that ranges from 1 to nPL, t MAX PL ( i )

is the maximum fluence occurring over the vessel ID occupied by a particular plate, PL ( i )

RTNDT (u ) is the unirradiated RTNDT of a particular plate, and T30PL ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to t MAX PL ( i )

of a particular plate.

RTMAX-FO characterizes the resistance of the RPV to fracture initiating from flaws in forgings that are not associated with welds. It is evaluated using the following formula for each forging within the beltline region of the vessel.

The value of RTMAX-FO assigned to the vessel is the highest of the reference temperature values associated with any individual plate. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld and plate evaluated is also needed.

n FO RTMAX FO MAX RTNDT ( u ) T30 FO ( i ) FO ( i )

t MAX FO ( i )

i 1 where nFO is the number of forgings in the beltline region of the vessel, i is a counter that ranges from 1 to nFO, t MAX FO ( i )

is the maximum fluence occurring over the vessel ID occupied by a particular forging, FO ( i )

RTNDT (u ) is the unirradiated RTNDT of a particular forging, and 33

T30FO ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to t MAX FO ( i )

of a particular forging.

RTMAX-CW characterizes the resistance of the RPV to fracture initiating from flaws found along the circumferential weld fusion lines. It is evaluated using the following formula for each circumferential weld fusion line within the beltline region of the vessel (the part of the formula inside the {}). Then the value of RTMAX-CW assigned to the vessel is the highest of the reference temperature values associated with any individual circumferential weld fusion line. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld, plate, and forging evaluated is also needed.

RTNDT adj cw ( i )

T30adj cw(i ) t FL ,

(u )

MAX MAX CWFL(i) RTNDT T30adj pl (i ) t FL ,

n CWFL adj pl ( i )

RTMAXCW (u )

i 1 RT adj fo ( i ) T adj fo ( i ) t NDT ( u ) 30 FL where nCWFL is the number of circumferential weld fusion lines in the beltline region of the vessel, i is a counter that ranges from 1 to nCWFL, tFL is the maximum fluence occurring on the vessel ID along a particular circumferential weld fusion line, adj cw ( i )

RTNDT (u ) is the unirradiated RTNDT of the weld adjacent to the ith circumferential weld fusion line, adj pl ( i )

RT NDT ( u ) is the unirradiated RTNDT of the plate adjacent to the ith circumferential weld fusion line (if there is no adjacent plate this term is ignored),

adj fo ( i )

RTNDT (u ) is the unirradiated RTNDT of the forging adjacent to the ith circumferential weld fusion line (if there is no adjacent forging this term is ignored),

T30adj cw(i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the weld adjacent to the ith circumferential weld fusion line, T30adj pl ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the plate adjacent to the ith axial weld fusion line(if there is no adjacent plate this term is ignored), and T30adj fo (i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the forging adjacent to the ith axial weld fusion line(if there is no adjacent forging this term is ignored).

34

The T30 values in the preceding equations are determined as follows  :

T30 MD CRP MD A1 0.001718TRCS 1 6.130PMn 2.471 te 1.100 T

CRP B 1 3.769 Ni 1.191 RCS f Cu e , P g Cu e , Ni, te 543.1 1.140x10 7 for forgings A 1.561x10 7 for plates 1.417 x10 7 for welds 102.3 for forgings 102.5 for plates in non - CE manufactured vessels B

135.2 for plates in CE manufactured vessels 155.0 for welds t for 4.3925 1010 te 4.3925 1010 0.2595 10 t

for 4.3925 10 Note: Flux () is estimated by dividing fluence (t) by the time (in seconds) that the reactor has been in operation.

log t 1.1390Cue 0.4483Ni 18.12025 g Cue , Ni, te tanh 10 e 1 1 2 2 0.6287 0 for Cu 0.072 f Cue , P Cue 0.072 for Cu 0.072 and P 0.008 0.6679 Cu 0.072 1.359( P - 0.008)0.6679 for Cu 0.072 and P 0.008 e

0 for Cu 0.072 wt%

Cue Cu for Cu 0.072 wt%

0.370 for Ni 0.5 wt%

Max(Cue ) 0.2435 for 0.5 Ni 0.75 wt%

0.301 for Ni 0.75 wt% (all welds with L1092 flux)

Step 3. Estimate the 95th percentile TWCF value for each of the axial weld flaw, plate flaw, circumferential weld flaw, and forging flaw populations using the RTs from Step 2 and the following formulae. RT must be expressed in degrees Rankine. The TWCF

The results reported in Appendix C demonstrate that the alternative form of this relationship presented in Chapter 7 of (Eason 07) has no significant effect on the TWCF values estimated by FAVOR. Thus, the equations in Appendix C could be used instead of the equations presented in Step 2 without the need to change any other part of the procedure.

35

contribution of a particular axial weld, plate flaw, circumferential weld, or forging is zero if either of the following conditions are met: (a) if the result of the subtraction from which the natural logarithm is taken is negative, or (b)if the beltline of the RPV being evaluated does not contain the product form in question.

TWCF95 AW exp5.5198 lnRTMAX AW 616 40.542 TWCF95 PL exp23.737 ln RTMAX PL 300 162.38 TWCF95CW exp9.1363 ln RTMAX CW 616 65.066 TWCF95 FO exp23.737 ln RTMAX FO 300 162.38 1.3 10 137 10 0.185RTMAX FO The factor = 0 if the forging is compliant with Regulatory Guide 1.43; otherwise = 1.

The factor is determined as follows:

If TWALL 91/2 -in, then = 1.

If 91/2 < TWALL < 111/2 -in, then = 1+ 8(TWALL - 91/2)

If TWALL 111/2 -in, then = 17.

Step 4. Estimate the total 95th percentile TWCF for the vessel using the following formulae (note that depending on the type of vessel in question certain terms in the following formula will be zero). TWCF95-TOTAL must be less than or equal to 1x10-6.

AW TWCF95 AW TWCF 95 PL TWCF95TOTAL PL CW TWCF95CW FO TWCF95 FO is determined as follows:

If RTMAX-xx 625R, then = 2.5 If 625R < RTMAX-xx < 875R then 2.5

1. 5 RTMAX xx 625 250 If RTMAX-xx 875R, then = 1 Table 3.3 and Table 3.4 provide the RTs and through EOLE the contribution of underclad TWCF95 values estimated by this procedure for cracks to the total TWCF of ring-forged plants is every currently operating PWR. In Table 3.4 estimated to be vanishingly small because, even TWCF95 values are reported for all ring-forged at EOLE, the embrittlement levels expected of vessels based on both the assumption that the ring forgings is low (at EOLE the highest underclad cracking can occur and on the RTMAX-FO of any ring-forged plant is 199 F).

assumption that underclad cracking cannot occur. No judgment regarding the incidence (or The graphs in Figure 3.11 summarize the TWCF not) of underclad cracking in any operating ring- values provided in these tables for all currently forged PWR is made in presenting these values. operating PWRs. Eighty-one percent of plate-However, these calculations do demonstrate that welded PWRs (100 percent of ring-forged for the embrittlement levels currently expected PWRs) have estimated TWCF95 values that are 36

two orders of magnitude or more below the operating nuclear RPV fleet are constructed.

1x10-6/ry regulatory limit (i.e., below 1x10-8/ry), This figure compares the histograms depicting even after 60 years of operation. After 40 years the distributions of the various RT values of operation the highest risk of PTS producing a characteristic of beltline materials in the current through-wall crack in any plate-welded PWR is operating fleet (projected to EOLE) to the 2.0x10-7/ry (for ring-forged PWRs this value is TWCF versus RT relationships used to define 1.5x10-10/ry). After 60 years of operation this the proposed PTS screening limits (see Figure risk increases to 4.3x10-7/ry (3.0x10-10/ry for 3.4 and Figure 3.9). These comparisons show ring-forged PWRs). Figure 3.12 provides a that the level of embrittlement in most plants is perspective on the relative contributions to the so low, even when projected to EOLE, that the total TWCF made by the various components estimated TWCF resulting from PTS is very, (axial welds, circumferential welds, plates, and very small.

forgings) from which the beltline regions of the Plate Welded Plants at 32 EFPY 14 Plate Welded Plants at 48 EFPY 14 Number of Currently Operating NumberAll ofCurrently Operating Ring Forged Plants at 32 EFPY Ring Forged Plants at 48 EFPY 12 12 2E-7 10 10 2E-7 to 4E-7 8 8 6 6 Power Reactors Power Reactors 4 4 2 2 0 0 elo E- w E 13 -1 elo E- w E 13 E- to E 12 -1 3 E- to E 12 -1

-1 3 E- to E 11 to 1 -1 2 E- to E 11 -1 2 E- E-10 1 0 to E- Eto 1 10 -1 0 E- E 9 to -9 E- E-9 to to 9 E- E 8

E- E to -8 E- E 8 to -8 B 7 to E--7 6 B E- E 7 to E--7 6

Estimated Yearly Through Wall Cracking Frequency Figure 3.11. Estimated distribution of TWCF for currently operating PWRs using the procedure detailed in Section 3.5.1 37

Table 3.3. RT and TWCF Values for Plate-Welded Plants Estimated Using the Procedure Described in Section 3.5.1 Values at 32 EFPY (EOL) Values at 48 EFPY (EOLE) 95th 95th Plant Name RTMAX-AW o RTMAX-CW RTMAX-AW o RTMAX-CW RTMAX-PL [ F] Percentile RTMAX-PL [ F] Percentile

[oF] [oF] [oF] [oF]

TWCF (/ry) TWCF (/ry)

ARKANSAS NUCLEAR 1 121.0 84.0 184.6 3.7E-14 128.7 92.0 193.4 1.0E-13 ARKANSAS NUCLEAR 2 97.9 97.9 97.9 1.3E-13 112.3 112.3 112.3 4.7E-13 BEAVER VALLEY 1 183.3 214.8 214.8 1.3E-09 194.0 230.1 230.1 4.9E-09 BEAVER VALLEY 2 95.4 114.4 114.4 5.7E-13 103.4 126.6 126.6 1.6E-12 CALLAWAY 1 84.7 84.9 84.9 3.8E-14 92.6 92.8 92.8 8.1E-14 CALVERT CLIFFS 1 196.6 149.8 149.8 4.2E-09 213.5 168.1 168.1 2.7E-08 CALVERT CLIFFS 2 174.1 174.1 174.1 1.1E-10 192.4 192.4 192.4 2.5E-09 CATAWBA 2 82.9 82.9 82.9 3.1E-14 90.2 90.2 90.2 6.3E-14 COMANCHE PEAK 1 60.3 60.3 60.3 3.1E-15 69.3 69.3 69.3 8.0E-15 COMANCHE PEAK 2 44.3 44.3 44.3 5.1E-16 52.0 52.0 52.0 1.2E-15 COOK 1 159.1 161.1 204.8 2.4E-11 174.2 175.1 220.1 1.2E-10 COOK 2 160.2 174.1 174.1 6.0E-11 171.9 188.1 188.1 1.8E-10 CRYSTAL RIVER 3 135.4 122.5 193.0 1.2E-12 143.8 130.4 201.8 2.4E-12 DIABLO CANYON 1 191.3 130.5 130.5 1.9E-09 207.6 144.1 144.1 1.5E-08 DIABLO CANYON 2 181.4 191.5 191.5 5.1E-10 193.6 205.0 205.0 3.2E-09 FARLEY 1 134.8 164.7 164.7 3.1E-11 147.5 183.1 183.1 1.1E-10 FARLEY 2 153.5 184.4 184.4 1.2E-10 167.1 203.6 203.6 4.2E-10 FORT CALHOUN 204.1 131.1 169.9 1.0E-08 221.6 149.3 187.7 5.6E-08 INDIAN POINT 2 199.3 208.4 208.4 6.5E-09 219.4 225.0 225.0 4.8E-08 INDIAN POINT 3 236.8 236.8 236.8 1.7E-07 249.9 249.9 249.9 3.8E-07 MCGUIRE 1 166.0 119.9 119.9 2.6E-12 176.0 128.7 128.7 8.6E-11 MILLSTONE 2 128.1 132.2 132.2 2.5E-12 139.4 144.2 144.2 6.6E-12 MILLSTONE 3 116.1 116.1 116.1 6.6E-13 128.8 128.8 128.8 1.9E-12 OCONEE 1 164.5 77.0 182.8 6.9E-13 174.4 84.3 191.9 5.3E-11 PALISADES 217.2 181.6 207.7 3.8E-08 237.2 200.4 227.5 1.7E-07 PALO VERDE 1 90.6 90.6 90.6 1.1E-12 101.9 101.9 101.9 3.2E-12 PALO VERDE 2 60.6 60.6 60.6 5.4E-14 71.9 71.9 71.9 1.8E-13 PALO VERDE 3 50.6 50.6 50.6 1.8E-14 61.9 61.9 61.9 6.2E-14 POINT BEACH 1 172.5 117.5 222.4 3.4E-11 185.7 125.6 238.8 7.9E-10 ROBINSON 2 136.8 141.8 199.8 5.6E-12 146.4 152.3 213.8 1.4E-11 SALEM 1 212.8 218.2 218.2 2.7E-08 225.9 232.0 232.0 8.0E-08 38

Values at 32 EFPY (EOL) Values at 48 EFPY (EOLE) 95th 95th Plant Name RTMAX-AW o RTMAX-CW RTMAX-AW o RTMAX-CW RTMAX-PL [ F] Percentile RTMAX-PL [ F] Percentile

[oF] [oF] [oF] [oF]

TWCF (/ry) TWCF (/ry)

SALEM 2 171.2 153.0 153.0 3.1E-11 185.7 166.7 166.7 7.9E-10 SEABROOK 79.4 79.4 79.4 2.2E-14 88.2 88.2 88.2 5.2E-14 SHEARON HARRIS 143.0 158.7 158.7 2.0E-11 150.8 169.8 169.8 4.4E-11 SONGS-2 133.8 133.8 133.8 2.9E-12 149.2 149.2 149.2 9.7E-12 SONGS-3 104.1 104.1 104.1 2.3E-13 118.5 118.5 118.5 8.1E-13 SOUTH TEXAS 1 42.4 47.6 47.6 7.5E-16 49.7 56.0 56.0 1.9E-15 SOUTH TEXAS 2 21.3 26.2 26.2 5.7E-17 28.3 34.4 34.4 1.6E-16 ST. LUCIE 1 158.2 143.4 143.4 6.2E-12 169.2 155.2 155.2 2.4E-11 ST. LUCIE 2 124.8 124.8 124.8 1.4E-12 136.0 136.0 136.0 3.4E-12 SUMMER 107.7 107.7 107.7 3.2E-13 119.4 119.4 119.4 8.7E-13 SURRY 1 239.2 138.7 198.7 2.0E-07 252.2 158.0 216.7 4.3E-07 SURRY 2 157.8 114.7 189.2 5.9E-13 169.8 133.3 207.2 1.4E-11 TMI-1 238.3 67.1 240.2 1.9E-07 247.7 74.3 249.4 3.3E-07 VOGTLE 1 72.5 72.5 72.5 1.1E-14 79.9 79.9 79.9 2.3E-14 VOGTLE 2 97.7 97.7 97.7 1.3E-13 108.4 108.4 108.4 3.4E-13 WATERFORD 3 73.6 73.6 73.6 1.2E-14 85.2 85.2 85.2 3.9E-14 WOLF CREEK 72.7 72.7 72.7 1.1E-14 80.0 80.0 80.0 2.4E-14 At 32 EFPY the fluence is the value reported in (RVID2) at EOL for the vessel ID. The 48 EFPY fluence is estimated as 1.5 times the 32 EFPY value.

Chemistry values are from (RVID2), except that manganese of 0.70 and 1.35 weight percent were used, respectively, for forgings and for welds/plates.

These defaults represent the approximate averages of the data used to establish the uncertainty distributions for FAVOR 06.1 (see Appendix A).

39

Table 3.4. RT and TWCF Values for Ring-Forged Plants Estimated Using the Procedure Described in Section 3.5.1 32 EFPY (EOL) 48 EFPY (EOLE) th 95 Percentile TWCF (/ry) 95th Percentile TWCF (/ry)

Plant Name RTMAX-FO RTMAX-CW without RTMAX-FO RTMAX-CW without with Underclad with Underclad

[oF] [oF] Underclad [oF] [oF] Underclad Cracking Cracking Cracking Cracking BRAIDWOOD 1 28.4 85.1 7.5E-17 7.5E-17 32.5 95.3 1.2E-16 1.2E-16 BRAIDWOOD 2 43.5 74.7 4.6E-16 4.6E-16 46.5 82.6 6.6E-16 6.6E-16 BYRON 1 70.7 70.7 9.2E-15 9.2E-15 77.5 77.5 1.8E-14 1.8E-14 BYRON 2 28.7 68.1 7.8E-17 7.8E-17 33.0 81.3 1.3E-16 1.3E-16 CATAWBA 1 41.1 41.1 3.5E-16 3.5E-16 46.2 46.2 6.4E-16 6.4E-16 DAVIS-BESSE 70.6 184.5 1.1E-14 1.1E-14 75.3 193.3 4.2E-14 4.2E-14 GINNA 187.2 196.6 1.4E-10 1.4E-10 195.4 209.8 2.5E-10 2.5E-10 KEWAUNEE 120.3 237.5 3.3E-11 3.3E-11 133.8 258.3 2.4E-10 2.4E-10 MCGUIRE 2 96.6 96.6 1.1E-13 1.1E-13 103.0 103.0 2.1E-13 2.1E-13 NORTH ANNA 1 159.1 159.1 2.0E-11 2.0E-11 168.4 168.4 4.0E-11 4.0E-11 NORTH ANNA 2 164.2 164.2 3.0E-11 3.0E-11 173.4 173.4 5.7E-11 5.7E-11 OCONEE 2 75.6 242.0 5.2E-11 5.2E-11 81.5 251.2 1.3E-10 1.3E-10 OCONEE 3 84.6 186.8 4.2E-14 4.2E-14 91.4 196.0 1.2E-13 1.2E-13 POINT BEACH 2 112.4 219.5 3.9E-12 3.9E-12 123.1 234.9 2.5E-11 2.5E-11 PRAIRIE ISLAND 1 85.1 125.4 3.9E-14 3.9E-14 101.1 148.4 1.7E-13 1.7E-13 PRAIRIE ISLAND 2 91.3 109.6 7.0E-14 7.0E-14 107.6 129.6 3.1E-13 3.1E-13 SEQUOYAH 1 187.3 187.3 1.5E-10 1.5E-10 198.6 198.6 3.0E-10 3.0E-10 SEQUOYAH 2 107.0 107.0 3.0E-13 3.0E-13 115.9 115.9 6.5E-13 6.5E-13 TURKEY POINT 3 102.2 215.8 2.2E-12 2.2E-12 108.9 230.1 1.4E-11 1.4E-11 TURKEY POINT 4 92.9 215.8 2.0E-12 2.0E-12 99.7 230.1 1.4E-11 1.4E-11 WATTS BAR 1 172.2 172.2 5.2E-11 5.2E-11 181.4 181.4 9.8E-11 9.8E-11 At 32 EFPY the fluence is the value reported in (RVID2) at EOL for the vessel ID. The 48 EFPY fluence is estimated as 1.5 times the 32 EFPY value.

Chemistry values are from (RVID2), except that manganese of 0.70 and 1.35 weight percent were used, respectively, for forgings and for welds/plates.

These defaults represent the approximate averages of the data used to establish the uncertainty distributions for FAVOR 06.1 (see Appendix A).

40

Beaver Beaver Beaver FAVOR 1.E-03 1.E-03 1.E-03 1.E-03 Oconee Results Oconee Oconee Bound Palisades 1.E-05 1.E-05 Palisades 1.E-05 Palisades 1.E-05 95th %ile TWCF - Axial Weld Flaws Fit 95 %ile TWCF for Underclad Flaws 95th %ile TWCF - Circ Weld Flaws Fit Fit 95th %ile TWCF - Plate Flaws 1.E-07 1.E-07 1.E-07 1.E-07 1.E-09 1.E-09 1.E-09 1.E-09 1.E-11 1.E-11 1.E-11 1.E-11 1.E-13 1.E-13 1.E-13 1.E-13 1.E-15 1.E-15 1.E-15 1.E-15 10 10 10 10

  1. of Plate # of Plate # of Plate # of Ring 1.E-17 8 1.E-17 8 1.E-17 8 1.E-17 8 6 6 6 6 1.E-19 1.E-19 1.E-19 th 1.E-19 4 4 Forged PWRs 4 4 1.E-21 2 Welded PWRs 1.E-21 2 Welded PWRs 1.E-21 2 Welded PWRs 1.E-21 2 0 0 0 0 1.E-23 1.E-23 1.E-23 1.E-23 450 550 650 750 850 450 550 650 750 850 450 550 650 750 850 450 550 650 750 850 Max RT AW [R] Max RT PL or RT FO [R] Max RT CW [R] Max RT FO [R]

10 10

  1. of Ring # of Ring 8 8 Histograms depict current estimates of RT 6 6 values at EOLE (48 EFPY) 4 4 2 Forged PWRs 2 Forged PWRs 0 0 475-500 525-550 575-600 625-650 675-700 475-500 525-550 575-600 625-650 675-700 Max. RT FO [R] Max. RT CW [R]

Figure 3.12. Comparison of the distributions (red and blue histograms) of the various RT values characteristic of beltline materials in the current operating fleet projected to 48 EFPY with the TWCF vs. RT relationships (curves) used to define the proposed PTS screening limits (see Figure 3.4 and Figure 3.9 for the original presentation of these relationships) 41

3.5.2 Limitation on RT Step 1. Establish the plant characterization parameters, which include the following:

RTNDT(u) [ F] The unirradiated value of RTNDT. Needed for each weld, plate, and forging in the beltline region of the RPV.

Cu [weight percent] Copper content. Needed for each weld, plate, and forging in the beltline region of the RPV.

Ni [weight percent] Nickel content. Needed for each weld, plate, and forging in the beltline region of the RPV.

P [weight percent] Phosphorus content. Needed for each weld, plate, and forging in the beltline region of the RPV.

Mn [weight percent] Manganese content. Needed for each weld, plate, and forging in the beltline region of the RPV.

t [seconds] The amount of time the RPV has been in operation.

TRCS [ F] The average temperature of the RCS inventory in the beltline region under normal operating conditions.

tMAX [n/cm2] The maximum fluence on the vessel ID for each plate and forging in the beltline region of the RPV.

tFL [n/cm2/sec.] The maximum fluence occurring along each axial weld and circumferential weld fusion line. This value is needed for each axial weld and circumferential weld fusion line in the beltline region of the RPV.

Twall [inches] The thickness of the RPV wall, including the cladding.

Step 2. Estimate values of RTMAX-AW, RTMAX-PL, RTMAX-FO, and RTMAX-CW using the following formulae and the values of the characterization parameters from Step 1:

RTMAX-AW characterizes the resistance of the RPV to fracture initiating from flaws found along the axial weld fusion lines. It is evaluated using the following formula for each axial weld fusion line within the beltline region of the vessel (the part of the formula inside the {}). The value of RTMAX-AW assigned to the vessel is the highest of the reference temperature values associated with any individual axial weld fusion line. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld and plate evaluated is also needed.

n AWFL RTNDT adj aw ( i )

T30adj aw(i ) t FL ,

MAX MAX AWFL(i) (u )

RTNDT ( u ) T30 t FL RTMAX AW adj pl ( i ) adj pl ( i )

i 1 where nAWFL is the number of axial weld fusion lines in the beltline region of the vessel, i is a counter that ranges from 1 to nAWFL, tFL is the maximum fluence occurring on the vessel ID along a particular axial weld fusion line, adj aw ( i )

RTNDT (u ) is the unirradiated RTNDT of the weld adjacent to the ith axial weld fusion line, 42

adj pl ( i )

RTNDT (u ) is the unirradiated RTNDT of the plate adjacent to the ith axial weld fusion line, adj aw ( i )

T 30 is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the weld adjacent to the ith axial weld fusion line, and T30adj pl (i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the plate adjacent to the ith axial weld fusion line.

RTMAX-PL characterizes the resistance of the RPV to fracture initiating from flaws in plates that are not associated with welds. It is evaluated using the following formula for each plate within the beltline region of the vessel. The value of RTMAX-PL assigned to the vessel is the highest of the reference temperature values associated with any individual plate. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld and plate evaluated is also needed.

t MAX n PL RTMAX PL MAX RTNDT PL ( i )

( u ) T30 PL ( i ) PL ( i )

i 1 where nPL is the number of plates in the beltline region of the vessel, i is a counter that ranges from 1 to nPL, t MAX PL ( i )

is the maximum fluence occurring over the vessel ID occupied by a particular plate, PL ( i )

RTNDT (u ) is the unirradiated RTNDT of a particular plate, and T30PL ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to t MAX PL ( i )

of a particular plate.

RTMAX-FO characterizes the resistance of the RPV to fracture initiating from flaws in forgings that are not associated with welds. It is evaluated using the following formula for each forging within the beltline region of the vessel.

The value of RTMAX-FO assigned to the vessel is the highest of the reference temperature values associated with any individual plate. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld and plate evaluated is also needed.

n FO RTMAX FO MAX RTNDT ( u ) T30 FO ( i ) FO ( i )

t MAX FO ( i )

i 1 where nFO is the number of forgings in the beltline region of the vessel, i is a counter that ranges from 1 to nFO, t MAX FO ( i )

is the maximum fluence occurring over the vessel ID occupied by a particular forging, FO ( i )

RTNDT (u ) is the unirradiated RTNDT of a particular forging, and 43

T30FO ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to t MAX FO ( i )

of a particular forging.

RTMAX-CW characterizes the resistance of the RPV to fracture initiating from flaws found along the circumferential weld fusion lines. It is evaluated using the following formula for each circumferential weld fusion line within the beltline region of the vessel (the part of the formula inside the {}). Then the value of RTMAX-CW assigned to the vessel is the highest of the reference temperature values associated with any individual circumferential weld fusion line. In evaluating the T30 values in this formula the composition properties reported in the RVID database are used for copper, nickel, and phosphorus. An independent estimate of the manganese content of each weld, plate, and forging evaluated is also needed.

RTNDT adj cw ( i )

T30adj cw(i ) t FL ,

(u )

MAX MAX CWFL(i) RTNDT T30adj pl (i ) t FL ,

n CWFL adj pl ( i )

RTMAX CW (u )

i 1 RT adj fo ( i ) T adj fo ( i ) t NDT ( u ) 30 FL where nCWFL is the number of circumferential weld fusion lines in the beltline region of the vessel, i is a counter that ranges from 1 to nCWFL, tFL is the maximum fluence occurring on the vessel ID along a particular circumferential weld fusion line, adj cw ( i )

RTNDT (u ) is the unirradiated RTNDT of the weld adjacent to the ith circumferential weld fusion line, adj pl ( i )

RT NDT ( u ) is the unirradiated RTNDT of the plate adjacent to the ith circumferential weld fusion line (if there is no adjacent plate this term is ignored),

adj fo ( i )

RTNDT (u ) is the unirradiated RTNDT of the forging adjacent to the ith circumferential weld fusion line (if there is no adjacent forging this term is ignored),

T30adj cw( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the weld adjacent to the ith circumferential weld fusion line, T30adj pl ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the plate adjacent to the ith axial weld fusion line(if there is no adjacent plate this term is ignored), and T30adj fo ( i ) is the shift in the Charpy V-Notch 30-foot-pound (ft-lb) energy (estimated using Eq. 3-4) produced by irradiation to tFL of the forging adjacent to the ith axial weld fusion line(if there is no adjacent forging this term is ignored).

44

The T30 values in the preceding equations are determined as follows § :

T30 MD CRP MD A1 0.001718TRCS 1 6.130PMn 2.471 te 1.100 T

CRP B 1 3.769 Ni 1.191 RCS f Cu e , P g Cu e , Ni, te 543.1 1.140x10 7 for forgings A 1.561x10 7 for plates 1.417 x10 7 for welds 102.3 for forgings 102.5 for plates in non - CE manufactured vessels B

135.2 for plates in CE manufactured vessels 155.0 for welds t for 4.3925 1010 te 4.3925 1010 0.2595 10 t

for 4.3925 10 Note: Flux () is estimated by dividing fluence (t) by the time (in seconds) that the reactor has been in operation.

log t 1.1390Cue 0.4483Ni 18.12025 g Cue , Ni, te tanh 10 e 1 1 2 2 0.6287 0 for Cu 0.072 f Cue , P Cue 0.072 for Cu 0.072 and P 0.008 0.6679 Cu 0.072 1.359( P - 0.008)0.6679 for Cu 0.072 and P 0.008 e

0 for Cu 0.072 wt%

Cue Cu for Cu 0.072 wt%

0.370 for Ni 0.5 wt%

Max(Cue ) 0.2435 for 0.5 Ni 0.75 wt%

0.301 for Ni 0.75 wt% (all welds with L1092 flux)

Step 3. Compare the RTs from Step 2 to the limits in Table 3.5. The limits on RTMAX-CW given in this table correspond to a TWCF95 limit of 1x10-8/ry, not 1x10-6/ry. This more restrictive limit was imposed to enable a simple two-dimensional representation of the

§ The results reported in Appendix C demonstrate that the alternative form of this relationship presented in Chapter 7 of (Eason 07) has no significant effect on the TWCF values estimated by FAVOR. Thus, the equations in Appendix C could be used instead of the equations presented in Step 2 without the need to change any other part of the procedure.

45

multidimensional relationship between the various RT values and TWCF95 illustrated inFigure 3.5 while not unduly diminishing the resulting 1x10-6/ry limits placed on RTMAX-AW and RTMAX-PL. Adoption of this lower limit for the TWCF produced by circumferential welds is not expected to have any practical impact because the highest projected values RTMAX-CW at EOLE are 250 F and 258 F for plate-welded and ring-forged plants (respectively), both of which are well below the limits on RTMAX-CW that appear in Table 3.5. Should changes in operations or other unforeseen changes that develop in the future increase a value of RTMAX-CW above the Table 3.5 limits, the licensee could always assess its plant using the approach that places a limit on TWCF described in Section 3.5.1.

Table 3.5. RT Limits for PWRs Limit on RT value for different values of TWALL [F]

RT Value >9.5 in., >10.5 in.,

9.5 in.

10.5 in. 11.5 in.

RTMAX-AW 269 230 222 RTMAX-PL 356 305 293 RTMAX-AW + RTMAX-PL 538 476 445 RTMAX-CW (see note below) 312 277 269 For RPVs complying with RG 1.43 356 305 293 RTMAX-FO For RPVs not complying with RG 246 241 239 1.43

-8 Note: The limit on RTMAX-CW corresponds to a TWCF value of 10 /ry. Should these limits on RTMAX-CW be exceeded, the RTMAX-AW, RTMAX-PL, RTMAX-FO, and RTMAX CW values should be used, along with Eq. 3-6, to estimate the total TWCF value. This total TWCF should be limited to 1x10-6.

Figure 3.13 and Figure 3.14 provide a graphical welded plants and 100 percent for ring-forged comparison of (1) the RT limits expressed in plants at EOL). At EOLE, 17 F separates the Table 3.5, (2) the RT limits derived from most embrittled plate-welded plant from these Eqs. 3-6 and 3-8, and (3) the RT values for screening limits (this number increases to 30 F operating PWRs at EOLE taken from Table 3.3 at EOL). For ring-forged plants at EOLE, 47 F and Table 3.4. These graphs show that 85 separates the most embrittled plant from the percent of all plate-welded plants and 90 percent most restrictive screening limit (the number of all ring-forged plants are 50 F or more away increases to 59 F at EOL).

from the proposed RT screening limits at EOLE (these numbers increase to 94 percent for plate-46

400 400 1x10-6/ry TWCF limit 350 350 Simplified Implementation RTMAX-AW 269F, and 1x10-6/ry TWCF limit 300 RTMAX-PL 356F, and 300 RTMAX-AW + RTMAX-PL 538F.

RTMAX-PL [oF] RTMAX-PL [oF]

250 250 Simplified Implementation RTMAX-AW 222F, and Plate Welded Plants RTMAX-PL 293F, and 200 at 48 EFPY (EOLE) 200 RTMAX-AW + RTMAX-PL 445F.

150 150 Palo Verde 1, 2, and 3 at 48 EFPY (EOLE) 100 100 50 50 0 0 0 50 100 150 200 250 300 0 50 100 150 200 250 300 o o RTMAX-AW [ F] RTMAX-AW [ F]

Figure 3.13. Graphical comparison of the RT limits for plate-welded plants developed in Section 3.5.2 with RT values for plants at EOLE (from Table 3.3). The top graph is for plants having wall thickness of 9.5-in. and less, while the bottom graph is for vessels having wall thicknesses between 10.5 and 11.5 in.

400 3.6 Need for Margin TWCF = 1x10-6/ry limit if in compliance with Reg. Guide 1.43 350 Aside from relying on different RT-metrics, the PTS screening limits proposed in Section 3.5 300 differ from the current 10 CFR 50.61 RTPTS TWCF = 1x10-6/ry RTMAX-FO [oF]

limit if not in compliance with Reg. Guide 1.43 screening limits by the absence of a margin 250 term. Use of a margin term is appropriate to account (at least approximately) for factors that TWCF = 1x10-8/ry limit 200 Ring Forged Plants occur in application that were not considered in 150 at 48 EFPY (EOLE) the analyses upon which these proposed screening limits are based. For example, the 100 10 CFR 50.61 margin term accounts for uncertainty in copper, nickel, and initial RTNDT.

50 However, as discussed in detail by (EricksonKirk-PFM), the NRC model explicitly 0

considers uncertainty in all of these variables 0 50 100 150 200 250 300 and represents these uncertainties as being larger o

RTM AX-CW [ F] (a conservative representation) than would be characteristic of any plant-specific assessment Figure 3.14. Graphical comparison of the RT limits for ring-forged plants application. Consequently, use of the developed in Section 3.5.2 with RT 10 CFR 50.61 margin term with the screening values for plants at EOLE (from limits proposed in this report would be Table 3.3) inappropriate.

The following additional reasons suggest that use of any margin term with the proposed screening limits is inappropriate:

47

(1) The TWCF values used to establish the early release in all circumstances. As screening limits represent 95th percentile discussed in Chapter 10 of NUREG-1806 values. through-wall cracking of the RPV is likely to lead to core damage, but large early (2) Information presented in Chapter 9 of release is unlikely for two reasons: (1)

NUREG-1806 (EricksonKirk-Sum) and because of reactor safety systems and the summarized in Section 3.2.1 herein multiple barriers that block radioactive demonstrates that the results from the three release to the environment plant-specific analyses apply to PWRs in (e.g., containment), and (2) because if a general.

through wall crack were to develop it would It is correct that certain aspects of the models happen when the temperature and pressure used to establish the proposed PTS limits cannot in the primary circuit are low, both of which be considered as best estimates. On balance, produce a low system energy. Current there is a conservative bias to these non-best- guidelines on core damage frequency estimate aspects of the analysis, as discussed in provided by Regulatory Guide 1.174 and the the following section. Option 3 framework for risk-informing 10 CFR Part 50 suggest a reactor vessel Throughout this project, every effort has been failure frequency limit of 1x10-5 made to perform a best estimate analysis. events/reactor year (RG1.174). Changing Nonetheless, comparison of the analytical from a 1x10-6 to a 1x10-5 limit would models used to assess risk with the actual increase all of the proposed RT limits situation being assessed reveals that certain by between 50 and 60 F (between 28 and features of that situation have not been 33 C).

represented as realistically as possible. These parts of the model may be judged as providing In the PRA model either a conservative representation (i.e., tending In the PRA binning process, if there was a to increase the estimated TWCF) or a question about what bin to place a particular nonconservative representation (i.e., tending to scenario in, the scenario was intentionally decrease the estimated TWCF) relative to the binned in a conservative manner. Thus, the actual situation in service. Table 3.6 loading severity has a tendency toward summarizes these conservatisms and being overestimated.

nonconservatisms, which are discussed in In the PRA model greater detail in Section 3.6.1 and Section 3.6.2, External initiating events. As detailed in respectively. This discussion does not include Section 9.4 of NUREG-1806 and in factors that the models do not accurately (Kolaczkowski-Ext), the NRCs analysis has represent when these inaccuracies have been not considered the potential for a PTS demonstrated to not significantly influence the transient to be started by an initiating event TWCF results. This information demonstrates external to the plant (e.g., fire, earthquake).

that, on balance, more conservatisms than The bounding analyses performed nonconservatisms remain in the model, demonstrate that this would increase the suggesting the appropriateness of applying the TWCF values reported herein by at most a proposed screening limits without an additional factor of 2. However, the bounding nature margin term.

of the NRCs external events analysis suggests strongly that the actual effect of 3.6.1 Residual Conservatisms ignoring the contribution of external initiating events is much smaller than 2 In the reactor vessel failure frequency limit times.

The reactor vessel failure frequency limit of The temperature of water held in the safety 1x10-6 events/reactor year was established injection accumulators was assumed to be based on the assumption that through-wall 60 F (15.6 C). These accumulators are cracking of the RPV will produce a large 48

inside containment and so exist at more readily than do flaws of infinite length temperatures of 80-90 F (26.7-32.2 C) because of systematic differences in the in the winter and above 110 F (43.3 C) through-wall variation of crack-driving in the summer. This conservative estimate force. Because of this approximation, the of injection water temperature increases the NRC model tends to overestimate the magnitude of the thermal stresses that occur likelihood of through-wall cracking.

during of pipe breaks and reduces the As detailed in Section 4.2.3.1.3 of fracture resistance of the vessel steel. (EricksonKirk-PFM) and in (English 02),

When a main steamline breaks inside of the adopted FAVOR model of how fluence containment, the release of steam from the attenuates through the RPV wall is break pressurizes the containment structure conservative relative to experimental data to approximately 50 pounds per square inch As detailed in Section 4.2.2.2 of (psi) (335 kilopascals (kPa). Consequently, (EricksonKirk-SS) and in Appendix E the minimum temperature for MSLBs is to (EricksonKirk-PFM), the statistical bounded by the boiling point of water at distributions of copper, nickel, phosphorus, approximately 50 psi (335 kPa), or and RTNDT sampled by FAVOR approximately 260 F (126.7 C). However, overestimate the degree of uncertainty in the NRCs secondary-side breaks do not these variables relative to what can actually account for pressurization of containment, exist in any particular weld, plate, or so the minimum temperature calculated by forging.

RELAP for these transients is 212 F (100 C), or approximately 50 F (28 C) too While the FAVOR model corrects (on cold. This conservative estimate of the average) for the systematic conservative bias minimum temperature associated with an in RTNDT, the model overestimates the MSLB increases the magnitude of the uncertainty associated with the fracture thermal stresses and reduces the fracture toughness transition temperature metric.

resistance of the vessel steel. In the flaw model In the fracture model In the experimental data upon which the Once a circumferential crack initiates, it is flaw distribution is based, all detected assumed to instantly propagate 360 around defects were modeled as being crack-like the vessel wall. However, full and, therefore, potentially deleterious to the circumferential propagation is highly fracture integrity of the vessel. However, unlikely because of the azimuthal variation many of these defects are actually in fluence, which causes alternating regions volumetric rather than planar, making them of more embrittled and less embrittled either benign or, at a minimum, much less of material to exist circumferentially around a challenge to the fracture integrity of the the vessel wall. Thus, the NRC model tends vessel. Thus, the NRC model overestimates to overestimate the extent of cracking the seriousness of the defect population in initiated from circumferentially oriented RPV materials, which leads to overly defects because it ignores this natural crack pessimistic assessments of the fracture arrest mechanism. resistance of the vessel.

Once an axial flaw initiates, it is assumed to instantly become infinitely long. In reality, it only propagates to the length of an axial shell course (approximately 8 to 12 feet (approximately 2.4 to 3.7 meters)), at which point, it encounters tougher material and arrests. Even though a shell course is very long, flaws of finite length tend to arrest 49

FAVOR incorporates an interdependence oxidation is more than compensated for by between initiation and arrest fracture the conservatism of establishing a TWCF toughness values premised on physical limit based on LERF when many accident arguments (see Sections 5.3.1.1 and 5.3.1.2 sequences can only plausibly result in core of (EricksonKirk-PFM)). While the staff damage.

believes these models are appropriate, this In the PRA model view is not universally held (see reviewer comment 40D in Appendix B of NUREG- External initiating events. As detailed in 1806). The alternative model, with no Section 9.4 of NUREG-1806 and in interdependence between initiation and (Kolaczkowski-Ext), the NRCs analysis has arrest fracture toughness values, would not considered the potential for a PTS reduce the estimated values of TWCF. transient to be started by an initiating event external to the plant (e.g., fire, earthquake).

As detailed in Section 9.2.2.1 of NUREG- The bounding analyses performed 1806, the NRC has simulated levels of demonstrate that this would increase the irradiation damage beyond those occurring TWCF values reported herein by at most a over currently anticipated lifetimes using the factor of 2. However, the bounding nature most conservative available techniques. of the NRCs external events analysis suggests strongly that the actual effect of 3.6.2 Residual Nonconservatisms ignoring the contribution of external initiating events is much smaller than 2 In the reactor vessel failure frequency limit times.

Air oxidation. The large early release In the fracture model frequency (LERF) criterion provided in Through-wall chemistry layering.

Regulatory Guide 1.174, which was used to As detailed in (EricksonKirk-PFM),

establish the 1x10-6/ry TWCF limit, assumes FAVOR models the existence of a gradient source terms that do not reflect scenarios of properties through the thickness of the where fuel cooling has been lost, exposing RPV because of through-wall changes in the fuel rods to air (rather than steam).

copper content. These copper content Should such a situation arise, some portion changes arise from the fact that, given the of the reactor fuel would eventually be large volume of weld metal needed to fill an oxidized in an air environment, which would RPV weld, manufacturers used weld wire result in release fractions for key fission from multiple weld wire spools (having products (ruthenium being of primary different amounts of copper coating) to concern) that may be significantly (e.g., a completely fill the groove. The model factor of 20) larger than those associated adopted in FAVOR resamples the mean with fuel oxidation in steam environments.

copper content of the weld at the 1/4T, 1/2T, These larger release fractions could lead to and 3/4T locations through the thickness.

larger numbers of prompt fatalities than This resampling increases the probability of predicted for non-PTS risk-significant crack arrest because it allows the simulation scenarios. Nonetheless, the accident of less irradiation-sensitive materials, which progression event tree (APET) developed in could arrest the running crack before it fails Chapter 10 of NUREG-1806 demonstrates the vessel. If these weld layers did not occur that the number of scenarios in which air in a real vessel, the TWCF would increase oxidation is possible is extremely small, relative to those reported herein by a small certainly far smaller than the number of factor (approximately 2.5 based on the scenarios in which only core damage (not limited sensitivity studies performed).

LERF) is the only plausible outcome. Thus, the nonconservatism introduced by not explicitly considering the potential for air 50

Table 3.6. Non-Best-Estimate Aspects of the Models Used to Develop the RT-Based Screening Limits for PTS Situation Potential Conservatism in the Analytical Model The model assumes that all failures produce a large early release; however, in the accident progression event tree (APET) (Ch. 10, NUREG-1806), most sequences lead only to core damage.

An initiated axial crack is assumed to instantly propagate to infinite length.

In reality, the crack length will be finite and limited to the length of a single shell course because the cracks will most likely arrest when they If the vessel fails, what happens next?

encounter higher toughness materials in either the adjacent circumferential welds or plates.

o An initiated circumferential crack is assumed to instantly propagate 360 around the vessel ID. In reality, the crack length is limited because the azimuthal fluence variation places strips of tougher material in the path of the extending crack.

How the many possible PTS initiators are binned, and how TH transients are When uncertainty of how to bin existed, consistently conservative selected to represent each bin to the decisions were made.

PFM analysis The minimum temperature of an MSLB inside containment is modeled as approximately 50 F (28 C) colder than it can actually be because o

Characterization of secondary-side containment pressurizes as a result of the steam escaping from the break.

failures Stuck-open valves on the secondary side are conservatively modeled in Palisades.

Through-wall attenuation of neutron Attenuation is assumed to be more significant than measured in damage experiments.

Model of material unirradiated The statistical distributions sampled produce more uncertainty than could toughness and chemical composition ever occur in a specific weld, plate, or forging.

variability Correction for systematic conservative Model corrects for mean bias, but overrepresents uncertainty in RTNDT.

bias in RTNDT All defects found were assumed to be planar.

Flaw model Systematically conservative judgments were made when developing the flaw distribution model.

Interdependency of between initiation Model employed allows all initiated flaws a chance to propagate into the toughness and arrest toughness vessel.

Most conservative approach taken (increasing time vs. increasing Extrapolation of irradiation damage unirradiated RTNDT).

Situation Potential Nonconservatism in the Analytical Model If the vessel fails, what The potential for air oxidation has been ignored.

happens next?

The potential for external events (e.g., fires, earthquakes) initiating PTS transients has not been modeled explicitly. A conservative bounding analysis estimates the effect of External PTS initiators external events to be at most a factor of 2 increase in TWCF, but the likely increase is expected to be much less than 2 times.

Through-wall chemistry Model assumes that the mean level of copper can change 4 times through the vessel layering wall thickness. If copper layering is not present, the TWCF would increase.

51

3.7 Summary herein, that estimates the total TWCF from the RT values for the materials in the RPV This report presents the results of FAVOR 06.1 beltlineRT values that can be determined from calculations, compares them to the FAVOR 04.1 information in the NRCs RVID database, and results presented in NUREG-1806, and uses the surveillance program information (to develop an new results to propose two options for estimate for manganese content). Table 3.7 implementing these findings in a revision of the provides the recommended RT limits (i.e.,

PTS Rule (10 CFR 50.61). Changes made in implementation option 2. Assuming that current FAVOR 06.1 have placed a greater density in operating practices are maintained, the status of the upper tails of the TWCF distributions, currently operating PWRs relative to these limits resulting in the agencys adoption of the 95th is as follows:

percentile of the TWCF distribution for use in the analyses that produced the recommended For plate-welded PWRs implementation options. Nevertheless, as was The risk of PTS failure of the RPV is very reported previously in NUREG-1806, the NRC low. Over 80 percent of operating PWRs again finds that only the most severe transient have estimated TWCF values below 1x10-8 classes (i.e., medium- to large-diameter primary- /ry at EOLE.

side pipe breaks, valves on the primary side that stick open and may suddenly reclose later) At EOL the highest risk of PTS at any PWR contribute significantly to the TWCF. The is 2.0x10-7/ry. At EOLE this risk increases minor plant-to-plant variation of the thermal to 4.3x10-7/ry.

hydraulic characteristics of such transients cannot significantly alter the stresses borne by Eighty-five percent of all plants are 50 F or the vessel wall, and thus cannot significantly more away from the proposed RT screening alter the TWCF. Thus, the results presented limits at EOLE (this number increases to 94 herein can be regarded as being generally percent at EOL).

applicable to all PWRs currently operating in the United States. Also, the current results reinforce At EOLE, 17 F separates the most the finding from NUREG-1806 that it is the embrittled plant from these screening limits material properties associated with axially (this number increases to 30 F at EOL).

oriented flaws that dominate PTS risk. Thus, the embrittlement properties of axial welds and For ring-forged PWRs plates in plate-welded vessels and of forgings in The risk of PTS failure of the RPV is very ring-forged vessels are the most important low. All operating PWRs have estimated indicators of PTS risk. Conversely, the much TWCF values below 1x10-8/ry at EOLE.

lower probability that cracks initiated from circumferentially oriented flaws will propagate At EOL the highest risk of PTS at any PWR through wall makes the embrittlement properties is 1.5x10-10/ry. At EOLE this risk increases of circumferential welds much less important to 3.0x10-10/ry.

contributors to the total PTS risk.

Ninety percent of all plants are 50 F or The two recommended implementation options more away from the most restrictive of the include either (1) limiting the TWCF estimated proposed RT screening limits at EOLE (this for an operating plant to a total value no greater number increases to 100 percent at EOL).

than 1x10-6/ry or (2) limiting RT values of the various materials in the RPV beltline so that At EOLE 47 F separates the most their total TWCF is not permitted to exceed embrittled plant from these screening limits 1x10-6/ry. These options are completely (this number increases to 59 F at EOL).

equivalent and interchangeable because they are both based on the same formula, provided 52

Table 3.7. RT Limits for PWRs Limit on RT value for different values of TWALL [F]

RT Value 9.5 in. >9.5 in., 10.5 in. >10.5 in., 11.5 in.

RTMAX-AW 269 230 222 RTMAX-PL 356 305 293 RTMAX-AW + RTMAX-PL 538 476 445 RTMAX-CW (see note below) 312 277 269 RTMAX- For RPVs complying with RG 1.43 356 305 293 FO For RPVs not complying with RG 1.43 246 241 239 Note: The limit on RTMAX-CW corresponds to a TWCF value of 10-8/ry. Should these limits on RTMAX-CW be exceeded the RTMAX-AW, RTMAX-PL, RTMAX-FO, and RTMAX-CW values should be used, along with Eq. 3-6, to estimate the total TWCF value. This total TWCF should be limited to 1x10-6.

53

54 Chapter 4 - References 4.1 PTS Technical Basis Citations The following three sections provide the citations that, together with this report, comprise the technical basis for risk-informed revision of the PTS Rule. When these reports are cited in the text, the citations appear in italicized boldface to distinguish them from the related literature citations.

4.1.1 Summary EricksonKirk-Sum EricksonKirk, M.T., et al., Technical Basis for Revision of the Pressurized Thermal Shock (PTS) Screening Limits in the PTS Rule (10 CFR 50.61): Summary Report, NUREG-1806, U.S. Nuclear Regulatory Commission.

4.1.2 Probabilistic Risk Assessment Kolaczkowski-Oco Kolaczkowski, A.M., et al., Oconee Pressurized Thermal Shock (PTS) Probabilistic Risk Assessment (PRA), September 28, 2004, available in the NRCs Agencywide Documents Access and Management System (ADAMS) under Accession #ML042880452.

Kolaczkowski-Ext Kolaczkowski, A. et al., Estimate of External Events Contribution to Pressurized Thermal Shock (PTS) Risk, Letter Report, October 1, 2004, available in ADAMS under Accession #ML042880476.

Siu 99 Siu, N., Uncertainty Analysis and Pressurized Thermal Shock: An Opinion, U.S. Nuclear Regulatory Commission, 1999, available in ADAMS under Accession #ML992710066.

Whitehead-PRA Whitehead, D.L. and A.M. Kolaczkowski, PRA Procedures and Uncertainty for PTS Analysis, NUREG/CR-6859, U.S. Nuclear Regulatory Commission, December 31, 2004.

Whitehead-BV Whitehead, D.L., et al., Beaver Valley Pressurized Thermal Shock (PTS) Probabilistic Risk Assessment (PRA),September 28, 2004, available in ADAMS under Accession #ML042880454.

Whitehead-Gen Whitehead, D.W., et al., Generalization of Plant-Specific Pressurized Thermal Shock (PTS) Risk Results to Additional Plants, October 14, 2004, available in ADAMS under Accession

  1. ML042880482.

Whitehead-Pal Whitehead, D.L., et al., Palisades Pressurized Thermal Shock (PTS)

Probabilistic Risk Assessment (PRA), October 6, 2004, available in ADAMS under Accession #ML042880473.

4.1.3 Thermal-Hydraulics Arcieri-Base Arcieri, W.C., R.M. Beaton, C.D. Fletcher, and D.E. Bessette, RELAP5 Thermal-Hydraulic Analysis to Support PTS Evaluations for the Oconee-1, Beaver Valley-1, and Palisades Nuclear Power 55

Plants, NUREG/CR-6858, U.S. Nuclear Regulatory Commission, September 30, 2004.

Arcieri-SS Arcieri, W.C., et al., RELAP5/MOD3.2.2 Gamma Results for Palisades 1D Downcomer Sensitivity Study, August 31, 2004, available in ADAMS under Accession #ML061170401.

Bessette Bessette, D.E., Thermal-Hydraulic Evaluations of Pressurized Thermal Shock, NUREG-1809, U.S. Nuclear Regulatory Commission, May 30, 2005.

Chang Chang, Y.H., K. Almenas, A. Mosleh, and M. Pour-Gol, Thermal-Hydraulic Uncertainty Analysis in Pressurized Thermal Shock Risk Assessment: Methodology and Implementation on Oconee-1, Beaver Valley, and Palisades Nuclear Power Plants, NUREG/CR-6899, U.S. Nuclear Regulatory Commission.

Fletcher Fletcher, C.D., D.A. Prelewicz, and W.C., Arcieri, RELAP5/MOD3.2.2 Assessment for Pressurized Thermal Shock Applications, NUREG/CR-6857, U.S. Nuclear Regulatory Commission, September 30, 2004.

Junge PTS Consistency Effort, Staff Letter Report to file, October 1, 2004, available in ADAMS under Accession #ML042880480.

Reyes-APEX Reyes, J.N., et al., Final Report for the OSU APEX-CE Integral Test Facility, NUREG/CR-6856, U.S. Nuclear Regulatory Commission, December 16, 2004.

Reyes-Scale Reyes, J.N., et al., Scaling Analysis for the OSU APEX-CE Integral Test Facility, NUREG/CR-6731, U.S. Nuclear Regulatory Commission, November 30, 2004.

4.1.4 Probabilistic Fracture Mechanics Dickson-Base Dickson, T.L., and S. Yin, Electronic Archival of the Results of Pressurized Thermal Shock Analyses for Beaver Valley, Oconee, and Palisades Reactor Pressure Vessels Generated with the 04.1 Version of FAVOR, ORNL/NRC/LTR-04/18, October 15, 2004, available in ADAMS under Accession #ML042960391 Dickson-UG Dickson, T.L., and P.T. Williams, Fracture Analysis of Vessels Oak Ridge, FAVOR v04.1, Computer Code: Users Guide, NUREG/CR-6855, U.S. Nuclear Regulatory Commission, October 21, 2004.

EricksonKirk-PFM EricksonKirk, M.T., Probabilistic Fracture Mechanics: Models, Parameters, and Uncertainty Treatment Used in FAVOR Version 04.1, NUREG-1807, U.S. Nuclear Regulatory Commission, January 26, 2005.

EricksonKirk-SS EricksonKirk, M.T., et al., Sensitivity Studies of the Probabilistic Fracture Mechanics Model Used in FAVOR Version 03.1, NUREG-1808, U.S. Nuclear Regulatory Commission, November 30, 2004.

56

Kirk 12-02 EricksonKirk, M.T., Technical Basis for Revision of the Pressurized Thermal Shock (PTS) Screening Limits in the PTS Rule (10 CFR 50.61), December 2002, available in ADAMS under Accession #ML030090626.

Malik Malik, S.N.M., FAVOR Code Versions 2.4 and 3.1: Verification and Validation Summary Report, NUREG-1795, U.S. Nuclear Regulatory Commission, October 31, 2004.

Simonen Simonen, F.A., S.R. Doctor, G.J. Schuster, and P.G. Heasler, A Generalized Procedure for Generating Flaw Related Inputs for the FAVOR Code, NUREG/CR-6817, Rev. 1, U.S. Nuclear Regulatory Commission, October 2003, available in ADAMS under Accession

  1. ML051790410.

Williams Williams, P.T., and T.L. Dickson, Fracture Analysis of Vessels Oak Ridge, FAVOR v04.1: Computer Code: Theory and Implementation of Algorithms, Methods, and Correlations, NUREG/CR-6854, U.S.

Nuclear Regulatory Commission, October 21, 2004.

57

4.2 Literature Citations 10 CFR 50.61 Title 10, Section 50.61, Fracture Toughness Requirements for Protection against Pressurized Thermal Shock Events, of the Code of Federal Regulations, promulgated June 26, 1984.

10 CFR 50 App. H Appendix H to Part 50, Reactor Vessel Material Surveillance Program Requirements, of the Code of Federal Regulations, promulgated December 31, 2003.

ACRS 05 ACRSR-2116, Letter from Graham Wallis to Luis Reyes entitled Pressurized Thermal Shock (PTS) Reevaluation Project: Technical Basis for Revision of the PTS Screening Criterion in the PTS Rule, available in ADAMS under Accession # ML050730177.

ASME S4 AVIII ASME Boiler and Pressure Vessel Code,Section XI, Division I, 1989 Edition, 1989 Addenda, Appendix VIII, Supplement 4.

ASTM E900 ASTM E900-02, Standard Guide for Predicting Radiation-Induced Transition Temperature Shift in Reactor Vessel Materials, American Society for Testing and Materials, Philadelphia, Pennsylvania, 2002.

Becker 02 Becker, L., Reactor Pressure Vessel Inspection Reliability, Proceedings of the Joint EC-IAEA Technical Meeting on Improvements in In-Service Inspection Effectiveness, Petten, Netherlands, November 2002.

Dickson 07a Dickson, T.L., P. T. Williams, and S. Yin, Fracture Analysis of VesselsOak Ridge FAVOR, v06.1, Computer Code: Users Guide, ORNL/TM-2007/0031, Oak Ridge Natinoal Laboratory, 2007.

Dickson 07b Dickson, T.L., and S. Yin, Electronic Archival of the Results of Pressurized Thermal Shock Analyses for Beaver Valley, Oconee, and Palisades Reactor Pressure Vessels Generated with the 06.1 Version of FAVOR, ORNL/NRC/LTR-07/04.

Eason 07 Eason, E.D., G.R. Odette, R.K. Nanstad, and T. Yamamoto, A Physically Based Correlation of Irradiation-Induced Transition Temperature Shifts for RPV Steels, Oak Ridge National Laboratory, ORNL/TM-2006/530.

English 02 English, C., and W. Server, Attenuation in US RPV SteelsMRP-56, Electric Power Research Institute, June 2002.

EricksonKirk 06a EricksonKirk, Mark and Marjorie EricksonKirk, An Upper-Shelf Fracture Toughness Master Curve for Ferritic Steels, International Journal of Pressure Vessels and Piping 83 (2006) 571-583.

EricksonKirk 06b EricksonKirk, Marjorie and Mark EricksonKirk, The Relationship between the Transition and Upper-Shelf Fracture Toughness of Ferritic Steels, Fatigue Fract Engng Mater Struct 29 (2006) 672-684.

Kirk 03 Kirk, Mark, Cayetano Santos, Ernest Eason, Joyce Wright, and G.

Robert Odette, Updated Embrittlement Trend Curve for Reactor Pressure Vessel Steels, Transactions of the 17th International 58

Conference on Structural Mechanics in Reactor Technology (SMiRT 17), Prague, Czech Republic, August 17-22, 2003.

RG 1.43 Regulatory Guide 1.43, Control of Stainless Steel Weld Cladding of Low Alloy Steel Components, May 1973, ADAMS Accession No. ML003740095.

RG 1.162 Regulatory Guide 1.162, Thermal Annealing of Reactor Pressure Vessel Steels, U.S. Nuclear Regulatory Commission, February 1996.

RG 1.154 Regulatory Guide 1.154, Format and Content of Plant-Specific Pressurized Thermal Shock Safety Analysis Reports for Pressurized-Water Reactors, U.S. Nuclear Regulatory Commission, November 2002.

RG 1.174 Rev 1 Regulatory Guide 1.174, Rev. 1, An Approach for Using Probabilistic Risk Assessment in Risk-Informed Decisions on Plant-Specific Changes to the Licensing Basis, U.S. Nuclear Regulatory Commission, January 1987.

RVID2 Reactor Vessel Integrity Database, Version 2.1.1, U.S. Nuclear Regulatory Commission, July 6, 2000.

Schuster 02 Schuster, G.J., Technical Letter ReportJCN-Y6604Validated Flaw Density and Distribution within Reactor Pressure Vessel Base Metal Forged Rings, Pacific Northwest National Laboratory, for U.S. Nuclear Regulatory Commission, December 20, 2002.

Schuster 98 Schuster, G.J., S.R. Doctor, S.L. Crawford, and A.F. Pardini, 1998, Characterization of Flaws in U.S. Reactor Pressure Vessels:

Density and Distribution of Flaw Indications in PVRUF, NUREG/CR-6471, Vol. 2, U.S. Nuclear Regulatory Commission, Washington, D.C.

Tregoning 05 Tregoning, R., and P. Scott, Estimating Loss-of-Coolant Accident (LOCA) Frequencies through the Elicitation Process, NUREG-1829, U.S. Nuclear Regulatory Commission, June 2005.

Williams 07 Williams, P.T., T.L. Dickson, and S. Yin, Fracture Analysis of VesselsOak Ridge FAVOR, v06.1, Computer Code: Theory and Implementation of Algorithms, Methods, and Correlations, ORNL/TM-2007/0030, Oak Ridge Natinoal Laboratory, 2007.

59

60 APPENDIX A CHANGES REQUESTED BETWEEN FAVOR VERSION 05.1 AND FAVOR VERSION 06.1

24 March 2006 MEMORANDUM From: Mark EricksonKirk, NRC/RES To: Terry Dickson, ORNL Concurrence: Jennifer Uhle, NRC/RES Shah Malik, NRC/RES Bob Hardies, NRC/NRR Steve Long, NRC/NRR Barry Elliott, NRC/NRR Lambros Lois, NRC/NRR cc: B. Richard Bass, ORNL Subj: Changes requested between FAVOR Version 05.1 and FAVOR Version 06.1

Dear Terry:

As you are aware, over the past eight months staff from the NRCs Office of Nuclear Reactor Regulation (NRR) have reviewed the technical basis RES has proposed for a risk-informed revision of the pressurized thermal shock (PTS) rule (10 CFR 50.61). As a consequence of this review, I am requesting that ORNL take the following actions:

1. Make certain changes to FAVOR 05.1.
2. Issue a new version of FAVOR, Version 06.1, including revisions to both the Theory and the Users manuals.
3. Re-analyze the base-case for the three study plants (Oconee Unit 1, Beaver Valley Unit 1, and Palisades) using certain new input data and issue the results to the NRC.
4. Perform sensitivity studies to assess the effects of subclad cracking on the through wall cracking frequency associated with forged vessels and issue the results to the NRC.

The purpose of this memorandum is to document in detail the particular tasks you are requested to take within each of these actions, and (in the case of changes made to the FAVOR code) document the technical basis for the requested changes.

Should you have any questions or require clarification of any of the points made herein, please do not hesitate to contact me by email addressed to both mtk@nrc.gov and to markericksonkirk@verizon.net, or by telephone to 301-415-6015.

Many thanks, Mark T EricksonKirk A-1

Action 1: Change FAVOR 05.1 Note: Information provided at the beginning of each of the following tasks establishes the technical basis/motivation for the requested change to FAVOR. At the end of each task writeup, the specific requested change can be found in a box highlighted, as is this one, in pink.

Task 1.1 Change in the data basis for RTEPISTEMIC Question 1: Tables 4.1 and 4.2 in NUREG-1807 provide information on materials for which both RTNDT and To are known. It is only the information in Table 4.2 that is eventually used in FAVOR because it is only for this subset of materials for which enough KIc data are available to establish a RTLB value. There is a discrepancy between the To value given in these tables for HSST Plate 03 (shaded in gold in the tables). Table 4.1 gives a value of -21 F, while Table 4.2 gives a value of +31 F. What is the reason for the discrepancy?

Answer 1: The values were calculated from different sets of KJc data, which is the reason they are different. However, the +31 F value in Table 4.2 is not considered valid per ASTM E1921 procedures because all of the KJc values were measured at a temperature that is more than 90 F below To. The value of -21 F, which is valid per ASTM E1921, should therefore be used.

Action: In the FAVOR Theory manual (Table 10), change the value of To for HSST Plate 03 to -21 F, and change the resultant RTNDT-To value to +41 F.

A-2

Table 4.1 Summary of Unirradiated RPV Materials Having Both RTNDT and To Values Available Product Material RTNDT RTNDT - To Author Year Spec To [°F]

Form Designation [°F] [°F]

Iwadate, T. 1983 A508 Cl. 3 -54 -13 41 Marston, T.U. 1978 A508 Cl. 2 -6 65 71 Marston, T.U. 1978 Forging A508 Cl. 2 -60 51 111 VanDerSluys, W.A. 1994 A508 Cl. 3 -154 -22 132 Marston, T.U. 1978 A508 Cl. 2 -124 50 174 McGowan, J.J. 1988 A533B Cl. 1 HSST 02 -8 0 8 Marston, T.U. 1978 A533B Cl. 1 HSST 02 -17 0 17 Marston, T.U. 1978 A533B Cl. 1 HSST 01 -2 20 22 Ahlf, Jurgen 1989 A533B Cl. 1 HSST 03 -21 20 41 Onizawa, Kunio 1999 A533B Cl. 1 -99 -31 68 Ishino, S. 1988 Generic Plate -81 -13 68 CEOG 1998 A533B Cl. 1 -85 -15 70 Link, Richard 1997 Plate A533B Cl. 1 HSST 14A -70 10 80 McCabe, D.E. 1992 A533B Cl. 1 HSST 13A -110 -9.4 100 Onizawa, Kunio 1999 A533B Cl. 1 -152 -49 103 Ishino, S. 1988 Generic Plate -131 -22 109 CEOG 1998 A533B Cl. 1 -133 5 138 Marston, T.U. 1978 A533B Cl. 1 -74 65 139 Morland, E 1990 A533B Cl. 1 -142 5 147 Ingham, T. 1989 A533B Cl. 1 -154 5 159 Ishino, S. 1988 -39 -58 -19 Ishino, S. 1988 -98 -76 22 CEOG 1998 -126 -80 46 Ramstad, R.K. 1992 HSST 73W -78 -29.2 48 McCabe, D.E. 1994 Midland Nozzle -32 27 59 Ramstad, R.K. 1992 HSST 72W -70 -9.4 60 CEOG 1998 -138 -60 78 CEOG 1998 -136 -50 86 Weld Williams. 1998 Kewaunee 1P3571 -144 -50 94 McCabe, D.E. 1994 Midland Beltline -70 27 97 Marston, T.U. 1978 -105 0 105 CEOG 1998 -139 -20 119 CEOG 1998 -157 -30 127 CEOG 1998 -186 -50 136 CEOG 1998 -189 -50 139 Williams, J. 1998 -203 -50 153 Table 4.2 Three Reference Transition Temperatures Defined Using the ORNL 99/27 KIc Database A-3

Property Material Product Sample Reference Temperatures Uncert. Terms Set ID Description Form Size RTNDT(u) T0 RTLB RTNDT(u) - RTLB T0 N (°F) (°F) (°F) (°F) (°F) 1 HSST 01 Weld 8 0 -105 -64.3 105 64.3 2 A533 Cl. 1 Weld 8 0 -57 10.9 57 -10.9 3 HSST 01 Plate 17 20 -1 -77.8 21 97.8 4 HSST 03 Plate 9 20 31 -71.5 -11 91.5 5 A533 Cl. 1 Plate 13 65 -74 -121.4 139 186.4 6 HSST 02 Plate 69 0 -17 -2.1 17 2.1 7 A533B Weld 10 -45 -151 -187.2 106 142.2 8 A533B Weld/HA 6 0 -132 -162.4 132 162.4 Z

9 A508 Cl. 2 Forging 12 50 -124 -97.6 174 147.6 10 A508 Cl. 2 Forging 9 51 -60 0.9 111 50.1 11 A508 Cl. 2 Forging 10 65 -55 10.4 120 54.6 12 HSSI 72W Weld 12 -9.4 -70 -15.4 60.6 6 13 HSSI 73W Weld 10 -29.2 -78 -67.6 48.8 38.4 14 HSST 13A Plate 43 -9.4 -109 -42.6 99.6 33.2 15 A508 Cl. 3 Forging 6 -13 -46 -11.3 33 -1.7 16 Midland Nozzle Weld 6 52 -34 from -37.4 86 89.4 other sources 17 Midland Weld 2 23 -71 from -58.9 94 81.9 Beltline other sources 18 Plate 02 4th Irr. Plate 4 0 -8 from -62.3 8 62.3 other sources A-4

Question 2: When the RTLB data in Table 4.2 are plotted versus To (using the corrected value of To identified in Question 1), the plot shown below results. (Note that three To values have been added to the original table for materials 16-18; these values are backed in blue.) Is there a reason why 7 of the data points have RTLB values that are lower than To (these data are indicated in red print in Table 4.2 above), while 11 of the values have RTLB values higher than To?

50 0

-50 RT LB [ F]

o

-100

-150 Data RTLB = To

-200

-250

-200 -150 -100 -50 0 50 o

T o [ F]

Answer 2: The figure at the top of the next page, which is taken from the FAVOR 04.1 Theory Manual, indicates that RTLB is established for a particular data set using the following procedure:

1. Identify a set of ASTM E399 valid KIc data for which you want to identify RTLB and for which RTNDT is known.
2. Plot the KIc data, and also plot the ASME KIc curve located using RTNDT.
3. Shift the ASME KIc curve downward by 9.5 ksiin. and call this curve the Adjusted Lower Bound ASME KIc Curve.
4. Shift the Adjusted Lower Bound ASME KIc Curve leftward until it intersects the first measured KIc value. Call the amount by which the curve has been translated RTLB.
5. RTLB is now defined as RTLB = RTNDT - RTLB.

A-5

For data sets such as those shown in the figure above (i.e., those having KIc values measured over a range of temperatures), the RTLB value will always exceed the To value. This is illustrated in the figure at the top of the next page, where 100 KJc values are randomly simulated over the temperature range of -150 C T-To +75 C. The 11 actual sets of data for which RTLB exceeds To all have KIc values measured over a wide range of temperatures and so can be expected to have RTLB > To. We used the Master Curve to simulate 100 data sets of 100 KJc values over the temperature range of -150 C T-To +75 C (-270 F T-To +135 F). The 100 simulated RTLB values estimated from these simulated data exceeded To by, on average, 38 F (with a standard deviation of 19 F). This simulated amount by which RTLB exceeds To is in good agreement with the 11 actual data sets for which RTLB exceeds To by 41 F (on average). From this analysis, we draw the following conclusions:

RTLB should exceed To.

For well-populated data sets where KIc or KJc values are measured in transition, RTLB will be estimated to exceed To.

The average amount by which RTLB exceeds To for the 11 data sets shown in black type in Table 4.2 is in good agreement with our simulation based on the Master Curve.

A-6

250 KJc simulated based on MC 2.5% MC Bound Median MC 200 KJc [MPa*m0.5]

97.5% MC Bound RTLB Curve, RTLB = To + 25C 150 100 50 0

-200 -150 -100 -50 0 50 100 T-T o [oC]

The seven data sets shown in red type in Table 4.2 do not have measured KIc values distributed over a wide range of temperatures. In general, the measured KIc values for all five data sets fall in a range of temperatures between -111 C T-To -83 C (-200 F T-To -150 F). As illustrated by the simulation shown below, this places all of the measured KIc data very close to the lower shelf and causes the estimated value of RTLB to fall below To. To investigate the degree to which RTLB can be expected to fall below To for data sets of this type, we used the Master Curve to simulate 100 data sets of 20 KJc values over the temperature range of -111 C T-To -83 C (-200 F T-To -150 F). The 100 simulated RTLB values estimated from these simulated data fell below To by, on average, 77 F (with a standard deviation of 49 F). This simulated amount by which RTLB falls below To is well within one standard deviation of the seven actual data sets that have only KIc values on the lower shelf. These data sets, shown in red type in Figure 4.2, have RTLB values that fall below To by 43 F (on average). From this analysis, we draw the following conclusions:

250 KJc simulated based on MC 2.5% MC Bound Median MC 200 KJc [MPa*m ]

97.5% MC Bound 0.5 RTLB Curve, RTLB = To -45C 150 100 50 0

-200 -150 -100 -50 0 50 100 T-T o [oC]

RTLB will fall below To if the only KIc data available for analysis lie on or near the lower shelf.

A-7

The result RTLB < To is anomalous. It arises as a consequence of a limited amount of data that lie only on the lower shelf and, therefore, does not capture the temperature dependence inherent to transition fracture. RTLB < To does not reflect anything intrinsic about the material that should be simulated in FAVOR. Moreover, the KIc values estimated when RTLB falls below To become nonconservative at higher temperatures.

The data sets shown in red type in Table 4.2 should therefore not be used in the estimation of the RTEPISTEMIC value sampled in FAVOR to represent the difference between a known value of RTNDT and a simulated value of RTLB.

The plot below shows the relationship (or lack thereof) between RTLB and RTNDT for the 11 data sets in black type shown in Table 4.2. For purposes of illustration only, a nonparametric CDF derived from these data is also shown on the next page.

Action: Modify the data basis for the RTEPISTEMIC distribution used by FAVOR. The data used to establish the RTEPISTEMIC distribution should include only those data sets from Table 4.2 (see pages 4 and 5 of this memorandum) for which RTLB > To. Also, include the three new To values given for materials 16, 17, and 18 in the FAVOR Theory manual. The analysis methodology used to establish the RTEPISTEMIC distribution from these data should be the same as that used currently.

50 0

RTLB [ F]

o

-50

-100

-150

-100 -50 0 50 100 o

RT NDT [ F]

A-8

1.00 Cumulative Probability 0.75 0.50 0.25 0.00

-50 0 50 100 150 200 o

RT EPISTEMIC = RT NDT - RT LB [ F]

Task 1.2 Change in where the uncertainty in RTNDT(u) is sampled in the FAVOR looping structure The uncertainty assigned to a value of RTNDT(u) is a variable input to FAVOR. In practice, RTNDT(u) uncertainty is only assigned a nonzero value when the input value of RTNDT(u) is determined by the so-called generic method. In FAVOR Version 05.1, RTNDT(u) uncertainty is sampled inside of both the flaw and the vessel loops. Because FAVOR simulates the existence of hundreds of thousands of flaws in a particular major region in a particular vessel, the current sampling strategy implies that RTNDT(u) can vary point-wise throughout any one weld, plate, or forging. This simulation is inconsistent with the ASME definition of RTNDT(u). Per ASME, the value of RTNDT(u) assigned to a particular weld, plate, or forging must be the highest of any value calculated from all of the Charpy V-notch and nil-ductility temperature measurements made for the weld, plate, or forging in question. Per ASME, RTNDT(u) should therefore be single-valued for each major region in each simulated vessel.

Action: To reconcile this problem, ORNL is requested to modify the location where the RTNDT(u) uncertainty is sampled in FAVOR. RTNDT(u) uncertainty should be sampled inside of the vessel loop, but outside of the flaw loop.

Task 1.3 Change in where RTEPISTEMIC is sampled in the FAVOR looping structure The FAVOR program includes a series of nested FORTRAN DO-loops that are used to perform a Monte Carlo simulation. Of these, the outermost loop is called the vessel loop. Immediately inside the vessel loop is the flaw loop. In FAVOR Version 05.1, a new value of RTEPISTEMIC is sampled from the RTEPISTEMIC distribution for each new flaw simulated. The sampled RTEPISTEMIC value is used to estimate the reference temperature for the fracture toughness transition curve in the following way:

RTIrradiated RTNDT ( u ) RTEPISTEMIC RTSHIFT Cu , Ni, P, t For any particular simulated vessel, hundreds of thousands of individual flaws may be simulated to exist within a particular weld, plate, or forging (i.e., within what FAVOR refers to as a major region). Thus, A-9

the uncertainty simulated by FAVOR Version 05.1 in the RTIrradiated value will be as large as the uncertainty in RTEPISTEMIC, which, as shown by the graph at the top of the preceding page, can have a total range exceeding 150 F. This range is much larger than that measured in laboratory tests when fracture toughness samples were removed from different areas of a weld, plate, or forging.

Action: To reconcile this problem (i.e., that FAVOR 05.1 simulates an uncertainty on RTIrradiated that exceeds that measured in laboratory experiments), ORNL is requested to modify the location where the RTEPISTEMIC distribution is sampled in FAVOR. RTEPISTEMIC should be sampled inside of the vessel loop, but outside of the flaw loop.

No changes to the FAVOR code should be made inside the flaw loop to simulate the uncertainty associated with RTIrradiated. Once the actions requested in Tasks 1.2 and 1.3 are taken, there will be no uncertainty simulated within the flaw loop in either of the following variables, RTNDT(u) and RTEPISTEMIC.

However, there is uncertainty within the flaw loop in the RTShift value. This uncertainty arises as a consequence of uncertainties simulated in the Cu, Ni, P, and fluence values. The graph below shows the effect of these simulated uncertainties on the resultant uncertainty in RTShift and, consequently, the resultant uncertainty in RTIrradiated. It can be observed that, except at low mean copper values, FAVOR simulates more uncertainty in RTShift (and, consequently, in RTIrradiated) than is reflected in either the data from which Eason derived the embrittlement shift model or than is characteristic of uncertainty in the To reference temperature (ASTM E1921). If FAVOR simulates a negative RTShift value, it instead sets the RTShift used in the calculation to zero, which is why the simulated uncertainty in the low copper shift values is so small. The general overestimation by FAVOR of the uncertainty in RTShift occurs because information on chemical composition uncertainty from many sources had to be 60 Mean Cu = 0.05 Standard Deviation of 1000 Simulated combined to obtain enough data to Mean Cu = 0.10 Mean Cu = 0.20 establish a distribution (see discussion in 50 Mean Cu = 0.30 Appendix D of NUREG-1807). This Standard deviation of Eason m odel for w elds procedure tends to overestimate the Shift Values [ F]

variability in chemical composition that 40 o would characterize any individual weld.

30 Because of these factors, there is no need to add logic inside the flaw loop to simulate the uncertainty associated with RTIrradiated; 20 this uncertainty is already accounted for in FAVOR by simulating uncertainties in the 10 values of Cu, Ni, P, and fluence used in the calculations.

0 Action: No action is required. The above 0 1 2 3 4 5 comment was inserted for clarity. 19 2 Fluence / 10 [n/cm ]

Task 1.4 Change in where the standard deviation on copper and on nickel is sampled in the FAVOR looping structure The two figures below are taken from Appendix D of NUREG-1807. These graphs (and the related text in NUREG-1807 Appendix D) provide the technical basis for the standard deviation of both copper and nickel within a particular sub-region (i.e., within a particular weld). To be consistent with this data basis, FAVOR should sample these standard deviations once per major weld region in each simulated vessel.

A-10

This, however, is not what is done in FAVOR 05.1. FAVOR 05.1 simulates the Cu and Ni standard deviations inside of both the flaw and the vessel loops. The effect of this sampling protocol is that the standard deviation of Cu and Ni is modeled as varying point-wise throughout a particular weld.

Action: ORNL is requested to modify the location where the standard deviation on Cu and Ni for welds is sampled in FAVOR. The standard deviations for Cu and for Ni should be sampled inside of the vessel loop, but outside of the flaw loop.

Task 1.5 Change the embrittlement trend curve (RTShift equation)

Action: Add the following embrittlement trend curve as an option to FAVOR. Note that the units of TTS are F. The technical basis for this equation is currently being documented by Nanstad, Eason, and Odette and should be available in April 2006.

TTS MDterm CRPterm MDterm A1 0.001718TRCS 1 6.130PMn 2.471 te 1.100 T

CRPterm B 1 3.769 Ni1.191 RCS f Cu e , P g Cu e , Ni,te 543.1 1.140x10 7 for forgings A 1.561x10 7 for plates 1.417 x10 7 for welds 102.3 for forgings 102.5 for plates in non - CE manufactured vessels B

135.2 for plates in CE manufactured vessels 155.0 for welds A-11

t for 4.3925 1010 te 4.3925 1010 0.2595 10 t

for 4.3925 10 Note: The relationship for te is limited as follows: te = MAX(3t).

log t 1.1390Cue 0.4483Ni 18.12025 g Cue , Ni, te tanh 10 e 1 1 2 2 0.6287 0 for Cu 0.072 f Cue , P Cue 0.072 for Cu 0.072 and P 0.008 0.6679 Cu 0.072 1.359( P - 0.008)0.6679 for Cu 0.072 and P 0.008 e

0 for Cu 0.072 wt%

Cue Cu for Cu 0.072 wt%

0.370 for Ni 0.5 wt%

Max(Cue ) 0.2435 for 0.5 Ni 0.75 wt%

0.301 for Ni 0.75 wt% (all welds with L1092 flux)

The following items should be noted when implementing this formula in FAVOR:

Flux () is estimated by dividing fluence (t) by the time (in seconds) associated with the analysis. Time is calculated from EFPY.

The effective fluence (te) is limited to a maximum value of three times the fluence (i.e., 3t).

When estimating values of TTS for an embedded flaw having a crack-tip located z inches from the ID, the values flux () and fluence (t) at location z should be estimated as follows before the effective fluence (te) at location z is calculated:

1. ID fluence: ID , determined from the BNL fluence map t
2. ID flux: ID ID , where t is determined from EFPY t
3. Fluence at z: t z t ID exp 0.24 z
4. Flux at z: z ID exp 0.24 z t z for z 4.3925 1010 t e ( z )

0.2595

5. Effective fluence at z: 4.3925 1010 10 t z for z 4.3925 10 t e ( z ) MAX3 t z Task 1.6 Manganese sampling protocols and uncertainty In order to complete Task 1.5, information on the uncertainty in Mn data and sampling protocols for these data is needed. Mn data were obtained from the following sources:

A-12

1. Combustion Engineering Owners Group, Fracture Toughness Characterization of C-E RPV Materials, Draft Report, Rev. 0, CE NSPD-1118, 1998.
2. VanDerSluys, W.A., Seeley, R.R., and Schwabe, J.E., An Investigation of Mechanical Properties and Chemistry within a Thick MnMoNi Submerged Arc Weldment, Electric Power Research Institute Report, EPRI NP-373, February 1977.
3. Stelzman, W.J., Berggren, R.G., and Jones, T.N. Jr., ORNL Characterization of HSST Program Plates 01, 02, and 03, NUREG/CR-4092, March 1985.
4. Wang, J.A., Analysis of the Irradiation Data for A302B and A533B Correlation Monitor Materials, NUREG/CR-6413, November 1995.
5. Fyfitch, S., and Pegram, J.W., Reactor Vessel Weld Metal Chemical Composition Variability Study, B&W Nuclear Technologies Report, BAW-2220, June 1995.

These citations contained enough repeated measurements of Mn to enable estimation of the variability in Mn at both a global and a local level. Global and local variability are defined as follows:

Global variability occurs over an area referred to as a region in FAVOR. A region is any individual weld, plate, or forging. Regions have ID areas on the order of 102 to 103 square inches.

Local variability occurs over an area referred to as a sub-region in FAVOR. A sub-region is completely contained within a region and corresponds to an area of the vessel that has within it relatively minor variation in fluence. Sub-regions have ID areas on the order of 100 to 101 square inches.

Appendix D of NUREG-1807 provides a more complete description of how FAVOR simulates global and local variability in composition variables.

The data from these four citations are summarized in the table and the figure below. Based on this information, the following conclusions can be made:

The variability (standard deviation) of Mn is approximately independent of mean Mn level.

The local variability of welds is less than the global variability of welds.

The global variability of forgings is less than that of welds and plates. The global and local variability of forgings is approximately equal.

Regarding sampling/resampling protocols, the following shall be implemented in FAVOR for Mn:

The distinction between region and sub-region uncertainty that is currently made with regard to sampling of Cu, Ni, and P shall now also be made for Mn.

The recommendations of Task 1.4 for Cu and Ni shall be applied to Mn as well.

For welds, Cu, Ni, and P are resampled from the global (or region) uncertainty in the IGA Propagation Sub-Model each time the propagating crack extends past a 1/4T boundary. These same protocols shall be followed for resampling Mn in welds.

Global or Mn Product Number of Mn Mean Citation Data ID Local Standard Form Measurements Mn Variability Deviation NUREG/CR-4092 Plate 01-K Plate Global 9 1.356 0.095 Plate 01-MU Plate Global 3 1.403 0.032 Plate 02-FB Plate Global 3 1.490 0.010 A-13

Global or Mn Product Number of Mn Mean Citation Data ID Local Standard Form Measurements Mn Variability Deviation Plate 03-E Plate Global 5 1.348 0.052 B, OS, F1 Forging Local 4 0.648 0.005 B, 1/4, F1 Forging Local 5 0.644 0.005 A, 1/2, F1 Forging Local 5 0.636 0.011 A, 3/4, F1 Forging Local 4 0.648 0.010 A, IS, F1 Forging Local 4 0.650 0.008 All F1 Data Forging Global 22 0.645 0.009 B, OS, F2 Forging Local 2 0.720 0.014 B, 1/4, F2 Forging Local 3 0.737 0.006 A, 1/2, F2 Forging Local 3 0.740 0.017 EPRI NP-373 A, 3/4, F2 Forging Local 3 0.760 0.010 All F2 Data Forging Global 13 0.736 0.020 Flux A Weld Global 15 1.415 0.021 Flux B Weld Global 11 1.554 0.048 B, OS, W Weld Local 10 1.548 0.028 B, 1/4, W Weld Local 9 1.494 0.017 A, 1/2, W Weld Local 6 1.445 0.010 A, 3/4, W Weld Local 4 1.423 0.022 A, IS, W Weld Local 2 1.390 0.014 A302B Plate Global 4 1.375 0.037 HSST-01 Plate Global 16 1.392 0.090 NUREG/CR-6413 HSST-02 Plate Global 10 1.479 0.053 HSST-03 Plate Global 6 1.333 0.059 27204-B03 Weld Global 13 1.292 0.038 12008/13253-C08 Weld Global 13 1.282 0.078 3P7317-T07 Weld Global 13 1.452 0.043 90136-G11 Weld Global 13 1.067 0.034 33A277-D08 Weld Global 13 1.153 0.038 83637-N10 Weld Global 13 1.509 0.057 10137-E08 Weld Global 13 1.291 0.048 CE NPSD 944-P 33A277-C19 Weld Global 13 1.220 0.055 Rev. 2 27204-B03 Weld Local 5 1.264 0.018 12008/13253-C08 Weld Local 5 1.266 0.011 3P7317-T07 Weld Local 5 1.448 0.013 90136-G11 Weld Local 5 1.096 0.023 33A277-D08 Weld Local 5 1.162 0.024 83637-N10 Weld Local 5 1.498 0.008 10137-E08 Weld Local 5 1.274 0.015 33A277-C19 Weld Local 5 1.184 0.017 BAW-2220 10137 Weld Global 20 1.132 0.089 21935 Weld Global 7 1.489 0.050 20291/12008 Weld Global 29 1.252 0.079 33A277 Weld Global 38 1.136 0.093 10137 Plate Global 12 1.259 0.057 21935 Plate Global 7 1.404 0.067 A-14

Global or Mn Product Number of Mn Mean Citation Data ID Local Standard Form Measurements Mn Variability Deviation 20291/12008 Plate Global 17 1.341 0.101 33A277 Plate Global 24 1.348 0.088 Plate - Global 0.10 Mn Standard Deviation Forging - Global Forging - Local Weld - Global 0.08 Weld - Local 0.06 0.04 0.02 0.00 0.6 0.8 1.0 1.2 1.4 1.6 Mean Mn Actions: Model variability in Mn at both the global and local level by sampling from distributions as described in the following table. The original data used to generate these values will be supplied to ORNL for further analysis.

Regarding sampling/resampling protocols, the following shall be implemented in FAVOR for Mn:

The distinction between region and sub-region uncertainty that is currently made with regard to sampling of Cu, Ni, and P shall now also be made for Mn.

The recommendations of Task 1.4 for Cu and Ni shall be applied to Mn as well.

For welds, Cu, Ni, and P are resampled from the global (or region) uncertainty in the IGA Propagation Sub-Model each time the propagating crack extends past a 1/4T boundary. These same protocols shall be followed for resampling Mn in welds.

Condition Value Global Variability Global Variability Global Variability in Forgings and in Plates in Welds Local Variability in all Product Forms Mean Standard Deviation 0.0617 0.0551 0.0141 Standard Deviation of 0.0278 0.0217 0.0063 Standard Deviations A-15

Task 1.7 Change coefficients in upper-shelf model Work has continued in developing a model of upper-shelf fracture toughness and in establishing the relationship between upper-shelf and transition fracture toughness. As a result of this ongoing development work, some of the coefficients in the upper-shelf fracture toughness model implemented in FAVOR need to be changed, as detailed below.

Eq. 19: The 50.1 and 0.794 coefficients used in Eq. 19 (current version below) should be changed to 48.843 and 0.7985, respectively. The data supporting this change are given after the equation.

200 150 100 Fit to All Static Data TUS = 0.7985*To + 48.843 TUS [ C]

50 R2 = 0.9812 o

0 All Static Old

-50 New Linde 80

-100 Dynamic Linear (All Static)

-150

-200 -150 -100 -50 0 50 100 150 200 o

T o [ C]

Eq. 21: The 2.09 coefficient used in Eq. 21 (current version below) should be changed to 1.75. The data supporting this change are given after the equation.

A-16

1000 Old New 750 ZA Fit to Data, alpha=1.75 JIc - JIc(288) [kJ/m ]

2 500 250 0

-250

-150 -100 -50 0 50 100 150 200 250 300 o

Temperature [ C]

Eq. 23: The 62.023 and -0.0048 coefficients used in Eq. 23 (current version below) should be changed to 51.199 and -0.0056, respectively. The data supporting this change are given after the equation.

100 Standard Deviation of JIc 80 y = 51.199e -0.0056x R2 = 0.862 60 Values [kJ/m2]

40 20 0

-150 -100 -50 0 50 100 150 200 250 300 o

Temperature [ C]

A-17

Task 1.8 Enhance output Modify FAVOR as necessary to enable the user to output the following results for each vessel iteration:

the RTEPISTEMIC value sampled for that vessel iteration for each T-H transient simulated for that vessel for that vessel iteration:

the number of axial cracks that initiated the number of circumferential cracks that initiated the CPCI for axial cracks the CPCI for circumferential cracks the CPTWC for axial cracks the CPTWC for circumferential cracks the TWCF contribution from each T-H transient for that vessel iteration Also, modify FAVOR to print out values of RTMAX-AW, RTMAX-PL, and RTMAX-CW for each major region in the vessel beltline. Formulas for each value, taken from Eq. 8-1 through Eq. 8-3 of NUREG-1806, are as follows:

RTMAX-AW is evaluated for each of the axial weld fusion lines using the following formula.

In the formula, the symbol tFL refers to the maximum fluence occurring along a particular axial weld fusion line, and T30 is the shift in the Charpy V-notch 30 ft-lb energy produced by irradiation at tFL.

RTMAX AW MAX RT NDT ( u ) T30 plate plate t FL , RTNDT ( u ) T30 axialweld axialweld t FL RTMAX-CW is evaluated for each of the circumferential weld fusion lines using the following formula. In the formula, the symbol tMAX refers to the maximum fluence occurring over the ID in the vessel beltline region, and T30 is the shift in the Charpy V-notch 30 ft-lb energy produced by irradiation at tMAX.

RTMAX CW MAX RT NDT ( u ) T30 plate plate t MAX , RT NDT ( u ) T30 circweld circweld t MAX RTMAX-PL is evaluated for each plate using the following formula. In the formula, the symbol tMAX refers to the maximum fluence occurring over the ID in the vessel beltline region, and T30 is the shift in the Charpy V-notch 30 ft-lb energy produced by irradiation at tMAX.

RTMAX PL RTNDT ( u ) T30 plate plate t MAX Task 1.9 Temperature-dependent thermal-elastic properties In FAVOR Version 05.1 (and previous versions), the thermal-elastic material properties (Youngs Modulus, Poissons Ratio, and the coefficient of thermal expansion) were modeled conservatively as being temperature-invariant properties. The 06.1 version of FAVOR should be modified to implement temperature dependencies in these properties as described in the following reference:

M. Niffengger, The Proper Use of Thermal Expansion Coefficients in Finite Element Calculations, Laboratory for Safety and Accident Research, Paul Scherrer Institute, Wurenlingen, Switzerland.

A-18

Also, the clad-base stress free reference temperature and the through-wall weld residual stress profile models used in FAVOR Version 05.1 (and previous versions) were estimated assuming temperature-invariant thermal-elastic material properties (for information on this estimation, see T.L. Dickson, W.J.

McAfee, W.E. Pennell, and P.T. Williams, Evaluation of Margins in the ASME Rules for Defining the P-T Curve for an RPV, NUREG/CP-0166, Oak Ridge National Laboratory, Oak Ridge, Tennessee, Proceedings of the Twenty-Sixth Water Reactor Safety Meeting 1, 1999, pp. 47-72). For consistency, the FAVOR model for the clad-base stress free reference temperature should be rederived using temperature-dependent thermal-elastic material properties.

A-19

Action 2: Issue FAVOR Version 06.1 Once the tasks requested under Action 1 are complete and all consistency checks and internal software verifications have been performed, ORNL is requested to issue a new version of FAVOR, which will be designated as Version 06.1. Revised versions of the Theory manual, the users manual, example problems, and the distribution disks will be issued to the NRC project monitor for review and comment. All manuals will be prepared in NUREG/CR format.

After the manuals have been modified to address the NRC project monitors comments, they shall be re-issued and distributed to individuals/organizations taking part in the verification and validation (V&V) effort. Following V&V, any errors, inconsistencies, and anomalies identified will be fixed (subject to concurrence of the project monitor), and the manuals will be revised and re-issued.

A-20

Action 3: Reanalyze the Base-Case for the Three Study Plants Using FAVOR 06.1 Input: Repeat the analyses documented in ORNL/NRC/LTR-04/18 using FAVOR Version 06.1. Prior to performing this analysis, the input files should be changed only in the following manner:

1. Change the initiating event frequencies for primary side pipe breaks to be consistent with the information provided in NUREG-1829. Alan Kolaskowski of SAIC will provide the necessary input files.
2. Ensure that the global fluence uncertainty is coded as 11.8% and local fluence uncertainty is coded as 5.6% in the input files.
3. The embrittlement trend curve described in Task 1.4 should be selected. Input values of Mn for the various plates, forgings, and welds in the three study plants are detailed in the table appearing at the end of Action 3.
4. Change the current percentage of repair flaws in the flaw distribution from 2% to 2.3%.

Basis for Item 4: NRR correctly points out that the decision to include 2% repair flaws in the flaw distribution used in the baseline PTS analysis was a judgment made on the basis that a 2% repair weld volume exceeded the proportional volume of weld repairs to original fabrication welds observed in any of PNNLs work (the largest volume of weld repairs relative to original fabrication welds was 1.5%).

However, flaws in welds are almost always fusion line flaws, which suggests that their number scales in proportion to weld fusion line area, not in proportion to weld volume. To address this, RES tasked PNNL to reexamine the relative proportion of repair welds that occur on an area rather than a volume basis.

PNNL determined that the ratio of weld repair fusion area to original fabrication fusion area is 1.8% for the PVRUF vessel. Thus, the input value of 2% used in the FAVOR calculations can still be regarded as bounding.

FAVOR makes the assumption that a simulated flaw is equally likely to occur at any location through the vessel wall thickness. During discussions between RES and NRR staff regarding the technical basis information developed by RES, NRR questioned the validity of this assumption for the case of flaws associated with weld repairs. After further consideration, RES has determined that this assumption is incorrect, as evidenced by the following information. The figure below shows that if a flaw forms in a weld repair, it is equally likely to occur anywhere with respect to the depth of the excavation cavity.

However, the second figure below shows weld repair areas occur with much higher frequency close to the surfaces of the vessel then they do at mid-wall thickness. Taken together, this information indicates that a flaw due to a weld repair is more likely to be encountered close to the ID or OD surface than it is at the mid-wall thickness.

A-21

1 0.9 0.8 Cummulative distribution ( faction) 0.7 0.6 0.5 Random distribution of flaw locations 0.4 0.3 0.2 0.1 0

0.00 0.20 0.40 0.60 0.80 1.00 Depth of Flaw from Cavity Surface (fraction)

Weld Repair Mouth Weld Repair Root 100%

NUREG/CR-6471, Vol.2 Percent of Repair 80% Repair made from ID (26 observations)

Repair made from OD (26 observations)

Combined (52 Observations)

Expon. (Combined (52 Observations))

60%

Excavations Extending to y = 1.1066e -0.558x R2 = 0.9773 40%

this Depth or Greater 20%

0%

0 1 2 3 4 5 6 7 8 Depth of Repair Excavation [inches]

FAVOR currently uses as input a blended flaw distribution for welds. The flaws placed in the blended distribution are scaled in proportion to the fusion area of the different welding processes used in the vessel. Because of this approach, it is not possible to specify a through thickness distribution of repair weld flaws that is biased toward the surfaces while maintaining a random through thickness distribution of SAW and SMAW weld flaws. Therefore, to account for the nonlinear through thickness distribution of weld flaws the 2% blending factor currently used for repair welds will be modified on the following basis:

In FAVOR, only flaws within 3/8T of the inner diameter can contribute to the vessel failure probability. Because PTS transients are dominated by thermal stresses, flaws buried in the vessel wall more deeply than 3/8T do not have a high enough driving force/low enough fracture toughness to initiate.

A-22

On the graph above, 3/8T corresponds to 3 in. The curve fit to the data on this graph indicates that 79% of all repair flaws occur within from 0 to 3/8T of the outer surfaces of the vessel. The figure above also indicates that 7% of all repair flaws occur between 5/8T and 1T from the outer surfaces of the vessel. Therefore, 43% ((79%+7%)/2) of all repair flaws occur between the ID and the 3/8T position in the vessel wall.

FAVORs current assumption of a random through-wall distribution of repair flaws indicates that 37.5% of all repair flaws occur between the ID and the 3/8T position in the vessel wall. Thus, FAVOR underestimates the 43% value based on the data given above.

To account for this underestimation, the 2% blend factor for repair welds will be increased to 2.3% (i.e., 2%43/37.5).

Output: Document the results of the PFM analyses performed with FAVOR 06.1 in the same format as that used in ORNL/NRC/LTR-04/18 and provide to the NRC project monitor for review and comment. Additionally, as soon as it is practicable after the FAVOR analyses are complete, and preferably in advance of issuance of the electronic archive letter report, provide results in MS Excel spreadsheets to the NRC project monitor for analysis.

A-23

Table of plant-specific input values for use in FAVOR calculations revised to include mean Mn values. This table will appear as Appendix D in the FAVOR Theory manual and as Appendix C in NUREG-1807.

RTNDT(u) [oF] Composition(2)

Product Form Heat Beltline flow(u) USE(u)

[ksi] RTNDT(u) RTNDT(u) (u) [ft-lb]

Cu Ni P Mn Method Value Value Beaver Valley 1, (Designer: Westinghouse, Manufacturer: CE)

Coolant Temperature = 547 F, Vessel Thickness = 7-7/8 in.

C4381-1 INTERMEDIATE SHELL B6607-1 83.8 MTEB 5-2 43 0 0.14 0.62 0.015 1.4 90 C4381-2 INTERMEDIATE SHELL B6607-2 84.3 MTEB 5-2 73 0 0.14 0.62 0.015 1.4 84 PLATE C6293-2 LOWER SHELL B7203-2 78.8 MTEB 5-2 20 0 0.14 0.57 0.015 1.3 84 C6317-1 LOWER SHELL B6903-1 72.7 MTEB 5-2 27 0 0.2 0.54 0.01 1.31 80 305414 LOWER SHELL AXIAL WELD 20-714 75.3 Generic -56 17 0.337 0.609 0.012 1.44 98 LINDE 1092 WELD 305424 INTER SHELL AXIAL WELD 19-714 79.9 Generic -56 17 0.273 0.629 0.013 1.44 112 LINDE 0091 WELD 90136 CIRC WELD 11-714 76.1 Generic -56 17 0.269 0.07 0.013 0.964 144 Oconee 1, (Designer and Manufacturer: B&W)

Coolant Temperature = 556 F, Vessel Thickness = 8.44-in.

AHR54 B&W FORGING LOWER NOZZLE BELT (4) 3 31 0.16 0.65 0.006 (5) 109 (ZV2861) Generic B&W C2197-2 INTERMEDIATE SHELL (4) 1 26.9 0.15 0.5 0.008 1.28 81 Generic B&W C2800-1 LOWER SHELL (4) 1 26.9 0.11 0.63 0.012 1.4 81 Generic PLATE B&W C2800-2 LOWER SHELL 69.9 1 26.9 0.11 0.63 0.012 1.4 119 Generic B&W C3265-1 UPPER SHELL 75.8 1 26.9 0.1 0.5 0.015 1.42 108 Generic B&W C3278-1 UPPER SHELL (4) 1 26.9 0.12 0.6 0.01 1.26 81 Generic INTERMEDIATE SHELL AXIAL WELD B&W LINDE 80 WELD 1P0962 79.4 -5 19.7 0.21 0.64 0.025 1.38 70 SA-1073 Generic INT./UPPER SHL CIRC WELD (OUTSIDE B&W 299L44 (4) -7 20.6 0.34 0.68 (3) 1.573 81 39%) WF-25 Generic NOZZLE BELT/INT. SHELL CIRC WELD B&W 61782 (4) -5 19.7 0.23 0.52 0.011 1.404 80 SA-1135 Generic INT./UPPER SHL CIRC WELD (INSIDE ASME NB-71249 76.4 10 0 0.23 0.59 0.021 1.488 67 61%) SA-1229 2331 UPPER/LOWER SHELL CIRC WELD SA- B&W 72445 (4) -5 19.7 0.22 0.54 0.016 1.436 65 1585 Generic B&W 8T1762 LOWER SHELL AXIAL WELDS SA-1430 75.5 -5 19.7 0.19 0.57 0.017 1.48 70 Generic B&W 8T1762 UPPER SHELL AXIAL WELDS SA-1493 (4) -5 19.7 0.19 0.57 0.017 1.48 70 Generic A-24

RTNDT(u) [oF] Composition(2)

Product Form Heat Beltline flow(u) USE(u)

[ksi] RTNDT(u) RTNDT(u) (u) [ft-lb]

Cu Ni P Mn Method Value Value 75.5 B&W 8T1762 LOWER SHELL AXIAL WELDS SA-1426 -5 19.7 0.19 0.57 0.017 1.48 70 Generic Palisades, (Designer and Manufacturer: CE)

Coolant Temperature = 532 F, Vessel Thickness = 81/2 in.

A-0313 D-3803-2 (4) MTEB 5-2 -30 0 0.24 0.52 0.01 1.35 87 B-5294 D-3804-3 (4) MTEB 5-2 -25 0 0.12 0.55 0.01 1.27 73 ASME NB-C-1279 D-3803-3 (4) -5 0 0.24 0.5 0.011 1.293 102 2331 PLATE ASME NB-C-1279 D-3803-1 74.7 -5 0 0.24 0.51 0.009 1.293 102 2331 ASME NB-C-1308A D-3804-1 (4) 0 0 0.19 0.48 0.016 1.235 72 2331 C-1308B D-3804-2 (4) MTEB 5-2 -30 0 0.19 0.5 0.015 1.235 76 LINDE 0124 WELD 27204 CIRC. WELD 9-112 76.9 Generic -56 17 0.203 1.018 0.013 1.147 98 34B009 LOWER SHELL AXIAL WELD 3-112A/C 76.1 Generic -56 17 0.192 0.98 (3) 1.34 111 LOWER SHELL AXIAL WELDS 3-LINDE 1092 WELD W5214 72.9 Generic -56 17 0.213 1.01 0.019 1.315 118 112A/C INTERMEDIATE SHELL AXIAL WELDS W5214 72.9 Generic -56 17 0.213 1.01 0.019 1.315 118 2-112 A/C Notes:

(1) Information taken from the July 2000 release of the NRCs Reactor Vessel Integrity (RVID2) database.

(2) These composition values are as reported in RVID2 for Cu, Ni, and P and as reported in RPVDATA for Mn. In FAVOR calculations, these values should be treated as the central tendency of the Cu, Ni, P, and Mn distributions detailed in Appendix D.

(3) No values of phosphorus are recorded in RVID2 for these heats. A generic value of 0.012 should be used, which is the mean of 826 phosphorus values taken from the surveillance database used by Eason et al. to calibrate the embrittlement trend curve.

(4) No strength measurements are available in PREP4 for these heats (PREP). A value of 77 ksi should be used, which is the mean of other flow strength values reported in this appendix.

(5) No values of manganese strength in RPVDATA for these heats (ref). A generic value of 0.80 should be used, which is the mean value of manganese for forgings taken from the surveillance database used by Eason et al. to calibrate the embrittlement trend curve.

A-25

Action 4: Perform Sensitivity Studies on Subclad Cracking In the spring of 2006, FAVOR 06.1 will be modified to run on the ORNL supercomputer cluster. At that time, ORNL is requested to work with the NRC project monitor to define a set of PFM analyses that can be used to quantify the effect of subclad cracks on TWCF. It is anticipated that the total scope of the effort will include approximately 8-10 PFM analyses (likely two plants, each run at 4 to 5 different EFPY). Reporting of results is needed to the same level of detail as was done for the subclad cracking sensitivity study performed by ORNL using FAVOR Version 05.1.

A-26

APPENDIX B REVIEW OF THE LITERATURE ON SUBCLAD FLAWS AND A TECHNICAL BASIS FOR ASSIGNING SUBCLAD FLAW DISTRIBUTIONS

TECHNICAL LETTER REPORT Review of the Literature on Subclad Flaws and a Technical Basis for Assigning Subclad Flaw Distributions PNNL Project Number: 43565 JCN Y6604 Task 4: Flaw Density and Distribution in RPVs F.A. Simonen February 2005 W.E. Norris, NRC Project Manager Prepared for Division of Engineering Technology Office of Nuclear Regulatory Research U.S. Nuclear Regulatory Commission DOE Contract DE-AC06-76RLO 1830 NRC JCN Y6604 Pacific Northwest National Laboratory P.O. Box 999 Richland, WA 99352 B-1

Review of Literature on Subclad Flaws and Technical Basis for Assigning Subclad Flaw Distributions F.A. Simonen Pacific Northwest National Laboratory Richland, Washington January 31, 2005 Introduction Pacific Northwest National Laboratory (PNNL) has assisted the U.S. Nuclear Regulatory Commission (NRC) in the efforts to revise the Pressurized Thermal Shock (PTS) Rule. In this role PNNL has provided Oak Ridge National Laboratory (ORNL) with inputs for the FAVOR code to describe distributions of fabrication flaws in reactor pressure vessels. These inputs, consisting of computer files, have been important to probabilistic fracture mechanics calculations with FAVOR. The flaw inputs have addressed seam welds, cladding and base metal materials, but had excluded subclad flaws associated with the heat-affected zone (HAZ) from the welding processes used to deposit stainless steel cladding to the inner surface of the vessel.

To address concerns expressed by a peer review committee, ORNL was requested by NRC to evaluate the potential contribution of subclad flaws to reactor pressure vessel failure. Based on information in available documents, PNNL estimated the number and sizes of subclad flaws in a forged pressure vessel, and provided input files to ORNL for sensitivity calculations. These sensitivity calculations predicted that subclad flaws could contribute significantly to calculated vessel failure probabilities. PNNL was then requested to continue its review of the literature for additional information on subclad flaws and to propose a refined basis for inputs to the FAVOR code.

The major sections of the present report:

1. describe the technical basis for the original subclad flaw input files that PNNL provided to ORNL for use with the FAVOR code
2. summarize results of a literature review performed by PNNL for information on characteristics of subclad flaws
3. propose and describe an improved method for generating distributions for subclad flaws and present results of example calculations
4. recommend future work to improve the flaw distribution model and the simulation of subclad flaws by the FAVOR code References (as listed at the conclusion of this report) provide information on a range of topics, including the metallurgical mechanisms that cause subclad cracks, measures that can prevent cracking, and fracture mechanics calculations that have evaluated the significance of subclad cracks. The main focus in the present report is on the characteristics of observed subclad flaws and more specifically on available data and prior estimates of the sizes and numbers of subclad flaws.

Technical Basis for Prior Subclad Flaw Distributions For welds, base metal, and cladding, PNNL has examined material and has used the data on observed flaws in the different material types to establish statistical distributions for the numbers and sizes of flaws.

However, none of the examined material showed evidence of subclad flaws. Therefore, the numbers and sizes of subclad flaws for a vessel susceptible to such cracking were estimated from a preliminary review B-2

of the literature. The primary source was a comprehensive paper summarizing European work during the 1970s (A. Dhooge et al., 1978). This paper was based mainly on experience with vessel cracking in Europe and subsequent research programs conducted during the 1970s. The paper was considered to be relevant to U.S. concerns with older vessels that may have been fabricated with European practices.

The survey of the literature showed that subclad cracks:

1. are shallow flaws extending into the vessel wall from the clad-to-base metal interface, and 4 mm is cited as a bounding through-wall depth dimension
2. have orientations normal to the direction of welding for clad deposition, giving axial cracks in a vessel beltline
3. occur as dense arrays of small cracks extending into the vessel wall
4. extend to depths limited by the depth of the heat-affected zone Figures in the cited paper show networks of cracks with flaw depths estimated from a micrograph being significantly less than the cited bounding 4-mm depth. The cracks extended perpendicular to the direction of welding and were clustered where the passes of the strip clad overlapped. Subclad flaws were said to be much more likely to occur in grades of pressure vessel steels that have chemical compositions that enhance the likelihood of cracking. Forging grades such as A508 are more susceptible than plate materials such as A533. High levels of heat inputs during the cladding process also enhance the likelihood of subclad cracking. Other details of the cladding process are also important, such as single-layer versus two-layer cladding.

The number of cracks per unit area of vessel inner surface was estimated from Figure 1, taken from the Dhooge paper. Cracking was shown to occur in bands estimated to have a width of 4 mm. This dimension was used to estimate the bounding lengths of subclad cracks. The longest individual cracks in Figure 1 were about 2 mm versus the 4-mm width dimension of the zone of cracking. Counting the number of cracks pictured in a small region of vessel surface gave a crack density of 80,512 flaws per square meter.

Figure 1 Location and Orientation of Underclad Crack; (a) Transverse Section; (b) Plan View of Cracks B-3

The flaw input files as provide to ORNL were based on the following assumptions:

1. The crack depth dimensions were described by a uniform statistical distribution from 0 to 4 mm with no cracks greater than 4 mm in depth.
2. The crack lengths were also described by a uniform statistical distribution. Like the assumption for flaws in seam welds, the amount by which flaw lengths exceed their corresponding depth dimension was taken to be a uniform distribution from 0 to 4 mm. Thus, the extreme length for a flaw with a depth dimension of 4 mm was 8 mm. The 4-mm deep flaws therefore had lengths ranging from 4 to 8 mm (aspect ratios from 1:1 to 2:1). Flaws with depths of 1 mm had lengths ranging from 1 mm to 5 mm (aspect ratios from 1:1 to 5:1).
3. The flaw density expressed as flaws per unit area was converted (for purposes of the FAVOR code) to flaws per unit volume using the total volume of metal in the vessel wall.
4. The file prepared for FAVOR assumed that the code would simulate flaws for the total vessel wall thickness, rather than just the Category 1 and 2 regions, which address only the inner three-eighths of the wall thickness. ORNL then accounted for this concern during the FAVOR calculations.

A very large number of flaws (> 130,000) per vessel was predicted based on the photograph of one small area of a vessel surface. The implication was that this area was representative of the entire vessel.

Although it is possible that subclad flaws can occur nonuniformly in patches of the vessel surface, it is generally understood that flaws occur in a widespread manner. Large numbers of flaws have been reported when the proper conditions for subclad cracking have existed. Based on PNNLs limited review of documents, it was therefore difficult to justify reductions of the estimated flaw density. However, sensitivity calculations should be performed to see if refinement of the estimated flaw density has a significant effect on the FAVOR calculations.

The estimated depth dimensions of the subclad flaws were thought to be conservative. The depth of 4 mm was based on statements regarding bounding flaw depths, with no other evidence such as micrographs or data on measured depth dimensions presented. The depth of 4 mm could be an estimate for the size of the heat-affected zone, which was then taken as a limitation on flaw depth. Alternatively, the 4-mm depth could be the extreme depth of some observed subclad flaws. The preliminary review showed some examples from metallography of subclad flaws, which showed only flaws of much smaller depths (< 2 mm). It is therefore suggested that sensitivity studies assumed subclad flaws with a bounding depth of 2 mm. The resulting FAVOR calculations included only flaws in the first bin corresponding to sizes 0 to 1 percent of the vessel wall thickness and predicted only small contribution for subclad flaws to vessel failure probabilities.

In summary, PNNLs preliminary estimates of subclad flaw distributions were based on a rather limited review of available literature, with a particular focus on the Dhooge 1978 paper. It was recommended that the scope of the literature review be expanded to seek sources of additional information. PNNL also proposed to review notes from past sessions with expert elicitation panels that have addressed reactor vessel fabrication and flaw distributions for the NRC. The critical need was information on the depth dimensions of subclad flaws. It was possible that the depth dimension of 4 mm is uncharacteristic of most subclad flaws, but is rather a bounding dimension based on consideration of heat-affected zones. It was possible that this depth has also been used in the literature for deterministic fracture mechanics calculations and could therefore reflect the conservative nature of inputs used for such calculations.

B-4

Results of Literature Review Individual papers and reports are summarized below.

Welding Research Council Bulletin No. 197 During the early 1970s, data on subclad cracking were assembled by the Task Group on Underclad Cracking under the Subcommittee on Thermal and Mechanical Effects of the Fabrication Division of the Pressure Vessel Research Committee. The following paragraphs from the report of the Task Group are extracted from Welding Research Council Bulletin No. 197 (Vinckier and Pense, 1974).

Underclad cracks were defined as intergranular separations no less than about 3 mm (0.12 in.) deep and 3 mm (0.12 in.) long found in the coarse-grained heat-affected zone of low-alloy steels underneath the weld-cladding overlay. Grain-boundary decohesions of sizes less than this were also included in the investigation. They are generally produced during postweld heat treatment. The combination of three factors that promote underclad cracking are a susceptible microstructures, a favorable residual-stress pattern and a thermal treatment bringing the steel into a critical temperature region, usually between 600 °C (1112 and 1202 °F) where creep ductility is low. Weld-overlay cladding with high-heat input processes provides the susceptible microstructure and residual-stress pattern, particularly where weld passes overlap, and postweld heat treatment provides the critical temperature.

High-heat-input weld-overlay techniques tend to increase the incidence of underclad cracks. Most underclad cracking was found in SA508 Class 2 steel forgings with some forged material chemical compositions found to be more sensitive than others. These forgings were clad with one-layer submerged-arc strip electrodes or multi-electrode processes. It was not reported in SA533 Grade B plate, nor was it produced when multilayer overlay processes were used.

Underclad cracking can be reduced or eliminated by a variety of means, but the most feasible appears to be by using a two-layer cladding technique, controlling welding process variables (e.g., low-heat-input weld processes) or renormalizing the sensitive heat-affected-zone region prior to postweld heat treatment. Control of welding process variables alone may not prevent all grain-boundary decohesions. Another solution would be to use materials that do not show the combination of a susceptible microstructure and low creep ductility or, where feasible, eliminate the thermal postweld heat-treatment cycle.

Other significant findings were:

Underclad cracking can include less severe manifestations of the same damage mechanisms as underclad cracks, but in the form of incipient cracks, microcracks, intergranular separations, pores, etc.

Underclad cracks are restricted to overlap of the clad passes and occur in the pattern and orientation as indicated in Figure 2.

Fracture mechanics evaluations established that subclad flaws with dimensions of 5 mm by 10 mm are not critical to safe operation.

Underclad cracking was widely reported in an industry survey as occurring in SA 508 Class 2 forgings. No cases of cracking were reported for SA 533 Grade B. One case of cracking was reported for SA 508 Class 3 consisting of separations less than 0.1-mm deep.

B-5

For purposes of the present review, it is noted that WRC Bulletin 197 has no information on reported depths of underclad cracks. There was, however, much discussion of the factors that govern the susceptibility of materials to underclad cracking along with descriptions of the material selections and welding procedures that can prevent underclad cracking.

Figure 2 Section of Clad Plate Showing Cracks French Work Underclad cracking has been observed in a number of reactor pressure vessels fabricated for French nuclear power plants. The French evaluation methods and requirements for vessel integrity (Pellissier Tanon et al., 1990; Buchalet et al., 1990; ASME, 1993; Moinereau et al., 2001) are based on several categories of reference defects. These defects address different defect locations, different mechanisms for the origin of defects, and a range of probabilities of defect occurrence. One of the categories is that of underclad defects, which are defects that have been of particular concern to French vessels. In terms of occurrence probabilities, the French evaluations have defined the following three defect classes.

Envelope defectsthose that have actually been observed during manufacturing, but with a size that cannot be exceeded realistically (1>P>10-2).

Exceptional defectsthose of the same type as envelope defects, but with a larger size to cover all the largest defects even seen in large primary circuit components (10-2>P10-4).

Conventional defectcovers configurations of very low probability (P<10-4).

Figure 3 shows the full scope of reference defects, with only the underclad crack being of interest to this discussion. For the envelope category, the underclad defect has a 3-mm through-wall dimension and a length of 60 mm. For the exceptional category, the underclad defect has a 6-mm through-wall dimension and a length of 60 mm.

Many of the original source documents for the French requirements were not available for the present review. However, ASME Section XI, with support by EPRI, has issued reports that provide information that is otherwise available only from the French literature. These ASME sources permitted the current review to be completed.

The French characterization of flaws was not specifically formulated for use in probabilistic fracture mechanics calculations, but has rather been used in France for deterministic calculations. The following B-6

discussion nevertheless provides some interpretations in the context of inputs for probabilistic calculations such as with the FAVOR code.

The probability values as cited above do not define units as needed to estimate flaw frequencies in terms of flaws per unit area or flaws per unit volume. The French publications imply that that probability values can be interpreted as the probability of having one or more flaws of the given sizes in a beltline vessel weld. This definition is difficult to apply to underclad cracks because these cracks occur in base metal rather than in welds. However, forged vessels such as those applicable to the French experience would have at most two circumferential welds in the beltline. It was therefore assumed that the probabilities can be treated as flaws per vessel. With this interpretation:

A flaw distribution for underclad cracks would have a maximum flaw depth of 3 mm and maximum flaw length of 60 mm. The probability range of 1>P>10-2 can be interpreted to mean that between 1 percent to 100 percent of a population of vessel welds would be subject to underclad cracking.

The probability range of 10-2>P10-4 can be interpreted to mean that between 1 percent to 0.01 percent of the vessels with underclad cracks will have a maximum flaw depth of 6 mm.

The probability of P<10-4 can be interpreted to mean that one vessel in 10,000 would have a fabrication surface flaw that extends through the entire clad and then into the base metal to give a total flaw depth of 13.5 mm. Such a flaw is outside the scope of the present discussion of underclad cracking, but has been addressed by ORNL as a low probability surface flaw.

Sensitivity studies by ORNL for underclad flaws were performed for maximum flaw depths of 2 mm and 4 mm. The 4-mm flaw is conservative in the context of the French work, because the French work could only support the assumption of a 3-mm maximum flaw depth. Uncertainty analyses could consider flaw depths as great as 6 mm, but this flaw depth should be weighted by a factor of 10-2 to 10-4 in constructing an uncertainty distribution.

It was noted that the French work used information on fabrication flaws collected from European manufacturers of vessels. For the underclad flaws, the exceptional defect depth of 6 mm came from considerations of the repair of underclad cracks. The French work indicated that the orientations of underclad cracks are expected to be longitudinal and that the use of a two-layer cladding will minimize the likelihood of underclad cracking.

Westinghouse Submittals Two topic reports from Westinghouse Electric were submitted to NRC to address the impact of underclad cracks on reactor pressure vessel integrity (Mager et al., 1971; Bamford and Rishel, 2000). The most recent report revisits concerns for underclad cracking to cover the period of license extension from 40 years to 60 years, and concludes that underclad cracks are of no concern relative to structural integrity of the reactor pressure vessel for a period of 60 years. Both the 1971 and 2000 WCAP reports were reviewed by NRC staff. A regulatory guide on weld cladding was issued (NRC, 1972). The NRC review of WCAP-15338 resulted in a request for addition information (NRC, 2002a) and a safety evaluation report (NRC, 2002b).

Because the 1971 Westinghouse report and RG 1.43 were not available to PNNL, the review was limited to the 2000 WCAP report and NRCs response to this report. Only limited information for estimating flaw distributions for PTS evaluations was found in the Westinghouse and NRC documents. The main focus was on deterministic fracture mechanics evaluations that covered such issues as fatigue crack growth, with no attention given to PTS evaluations. The fracture mechanics calculations assumed deterministic sizes of underclad cracks, with little documentation for the flaw size assumptions.

The 2000 WCAP report reviews the history of underclad cracking, including 1970 reports of reheat cracking and 1979 experience with cold cracking. Early reports of reheat cracks were limited in the B-7

United States with vessels fabricated by the Rotterdam Dockyard Manufacturing Company. Cold cracking was limited to a select group of six U.S. vessels. Reheat cracking has occurred with single-layer cladding using high heat input welding onto ASME SA-508 Class 2 forgings. The cracks are numerous and are confined to a depth of 0.125 inch (3 mm) and a width of 0.4 inch (10 mm).

Circumferential Direction: 1, 2, 8, 10, 11 Longitudinal Direction: 3, 4, 5, 6, 7, 9, 12 Figure 3 Reference Defects for Vessel Beltline from French Evaluations (dimensions in mm)

Cold cracking has been reported for ASME SA-508 Class 3 forgings after deposition of the second or third layer of cladding. Crack depths have varied from 0.007 inch (0.2 mm) to 0.295 inch (7.5 mm) and lengths have varied from 0.078 inch (2 mm) to 0.59 inch (15 mm). The WCAP reports indicate that cold cracking has not been observed in the vessel beltline, but rather at other locations such as nozzle bore regions. No occurrences of underclad cracks have been reported for plate materials or for SA-533B, SA-302E, or SA-302B forging materials.

B-8

NRC Expert Panels Two expert panels were formed as part of an NRC project during the 1990s to address concerns with flaws in reactor pressure vessels. The overall objective of this project was to review and expand the technical basis of the flaw distribution model of the PRODIGAL computer code (Chapman and Simonen, 1998) as developed in the United Kingdom by Rolls Royce and Associates. A meeting during 1994 focused on flaws in vessel seam welds. A followup meeting during 1996 focused on clad region flaws, including a discussion of underclad cracking. Although the experts provided useful and interesting insights and information on underclad cracking, the input from the experts was insufficient to provide the quantitative inputs needed to model underclad cracking in the PRODIGAL computer code.

The minutes of the two meetings (Simonen, 1994; Simonen, 1996) along with informal notes were reviewed. The following insights were expressed by the experts during the meetings:

Underclad cracking should be addressed from the standpoints of two timeframes, (1) cracking when the clad is deposited by welding and (2) cracking when a post-weld heat treatment is performed.

Reheat cracks can occur in coarse grained regions of 508 steel when post-weld heat treatment is performed.

Reheat cracks occur in clusters and have small depths of about 1 mm that cover the clad surface of the forging.

Reheat cracks form in the base metal and not in weld fill material. Reheat cracks never extend into the cladding material.

There should be no interaction of underclad cracks with other cracks due to lack of side wall fusion.

There is little reason for interaction between underclad cracks and previous HAZ cracks.

Post-weld reheat cracks can also occur along the HAZ of the side wall of the weld fill. The occurrence of underclad cracks would often be correlated with HAZ along the sidewall.

The same metallurgical cracking phenomena can occur for both underclad cracks and HAZ cracks with both occurring during stress relief post-weld heat treatment. Cracking is likely to occur (if it does occur) both as underclad and as HAZ, because the composition of the material is susceptible.

Some heats of material will be more susceptible than others due to material differences. The primary variable is chemical composition, and the occurrence of cracking is not much impacted by heat inputs.

Cracking actually occurs during post-weld heat treatment. The locations of cracks are related to weld beads.

The PRODIGAL weld simulation model could account for the compositions of forgings (508), and this information could be used to establish susceptibilities to underclad cracking. Utilities know forging composition, which could be used with a method described in an ASME paper which describes Nakwuma Number as the basis to predict susceptibility to reheat cracking (Horiya et al.,

1985).

A Framatome case of cold cracking (H2 cracking) was described that gives cracks parallel to the surface as an example of underclad cracks due to the heat inputs used in cladding. This cracking occurs only if there is a second layer of clad applied without preheat. B&W and CE were aware of the potential problem, which can occur in both the 533 and 508 materials, but is less likely to occur in weld metal. Cracking will also be in the form of a lack of bonding of the clad to base metal.

B-9

2000 Vessel Flaw Expert Judgment Elicitation The NRC has funded a number of efforts to re-evaluate the guidance and criteria in the Code of Federal Regulations as it relates to reactor vessel integrity, specifically pressurized thermal shock, which challenges the integrity of the reactor pressure vessels inner wall. One element of the re-evaluation required an accurate estimate of fabrication flaws, and this identified the need for the development of a generalized flaw distribution for domestic reactor pressure vessels. In order to develop the flaw distribution and resolve technical issues for which scientific uncertainty existed, an expert judgment process was used. The expert judgment process assisted the NRC staff in developing a generalized flaw distribution for domestic vessels, which has been used as input into probabilistic fracture mechanics calculations.

Although underclad cracking was not specifically addressed by the elicitation, some of the discussions with the experts provided some information of interest. The following remarks were compiled from detailed notes taken during interviews with the experts:

Other experts should address underclad cracking. It is estimated that there is a 1 in 50 probability of conditions for underclad cracking.

508 Class 2 materials had some problems with lack of bonding of clad to base metal. U.S. vessels did not have bonding problems with Class 2. The U.S. Navy stayed with the Class 2 material. The French changed to 508 Class 3.

One expert believed that Babcock and Wilcox had some cases of underclad cracking.

There can be underclad cracks for single-layer clad if the heat input is too high. There can also be underclad cracks with a two-layer clad without heat treatment between layers.

One expert had concerns with underclad cracks in 508 forgings. An EPRI report on French experience was mentioned.

Only 508 forgings are susceptible to underclad cracking reheat cracks. One of the experts did research and wrote a NUREG for NRC/ORNL about 7 years ago.

No reheat underclad cracking has been reported for plate materials. None of the experts was aware of H2 underclad cracking for plates. One expert estimated relative probabilities for underclad cracks for plates versus forgings.

Canonico/ORNL Report on Underclad Cracking Canonico (1977) reviews research on reheat cracks and the significance of such cracks to the integrity of reactor pressure vessels. The focus is on cracking in the heat-affected zones of seam welds rather than on underclad cracking. This report provides no specific information on the dimensions of cracks observed in nuclear vessels.

Frederick and Hernalsteen Frederick and Hernalsteen (1981) summarize experience with underclad cracking and evaluations of the significance of these cracks to vessel integrity. The information provided in this paper does not add to what is available in other more comprehensive review papers such at WRC Bulletin 197.

Dhooge et al.

Dhooge et al. (1978) provide an extensive review of experience and research in the area of reheat cracking in nuclear reactor pressure vessels, both underclad cracks and cracking of structural welds. The paper emphasizes European experience and research. Topics covered in the review paper are B-10

(1) incidence of cracking, (2) mechanism of cracking, (3) detection of reheat cracking, (4) tests for reheat cracking, (5) control of reheat cracking, and (6) significance of reheat cracking to structural integrity.

Figure 1 from Dhooge et al. (1978) shows the typical locations and orientations of underclad cracks.

Cracks occur only at locations that are heated twice by welding or, as in Figure 1, the areas of the overlap zone of the cladding weld passes. In this zone, the material is heated to a critical temperature by the second pass. The following paragraph on the sizes of underclad cracks is quoted:

The underclad cracks range in size from the short grain boundary separations only a few austenitic grains long and deep (0.2 mm) to a maximum of about 10 mm long and 4 mm deep. The usual depth is about 2.5 mm or less, the depth beneath the fusion boundary being governed by the depth of the grain coarsened HAZ and thus principally by the particular cladding procedure.

The Dhooge-reported incidence of cracking is consistent with the conclusions of WRC Bulletin 197.

Dolby and Saunders Dolby and Saunders note that subclad cracks often refer to conditions such as grain boundary separations or decohesions and in other cases to a series of micro voids. Therefore the term crack is subject to interpretation. A topical report issued by Babcock and Wilcox (Ayres et al., 1972) is cited for information on crack depth dimensions. Maximum reported depths of cracking are 4 mm, but depths are usually 2.5 mm or less, being governed by the extent of the heat-affected zone.

Other Papers A number of other papers are listed as references to the report. These papers were reviewed, but were found to provide little information that is important to the focus of the present report or to repeat and reinforce information from the other papers that have been discussed above.

Subclad Crack Sensitivity Study Input files for subclad flaw distributions were used by Oak Ridge National Laboratory and NRC staff to perform a sensitivity study (EricksonKirk, 2004). This sensitivity study was formulated as follows:

1. One set of forging properties was selected based on the Sequoyah 1 and Watts Bar 1 RPVs (RVID2).
2. One hypothetical model of a forged vessel was constructed based on an existing model of the Beaver Valley vessel. The hypothetical forged vessel was constructed by removing the axial welds and combining these regions with the surrounding plates to make a forging. This forging was assigned the properties from Step 1.
3. A FAVOR analysis of each vessel/forging combination from Steps 1 and 2 were analyzed at three embrittlement levels, 32 EFPYs, 60 EFPYs, and Ext-B. Thus, a total of three FAVOR analyses were performed (1 material property definition x 1 vessel definition x 3 embrittlement levels).

At 32 and 60 EFPYs, the through-wall crack frequency (TWCF) of the forging vessels was ~0.2 percent and 18 percent of the plate welded vessels. However, at the much higher embrittlement level represented by the Ext-B condition, the forging vessels had TWCF values 10 times higher than that characteristic of plate welded vessels at an equivalent level of embrittlement. While these very high embrittlement levels are unlikely to be approached in the foreseeable future, these results indicate that a more detailed assessment of vessel failure probabilities associated with subclad cracks would be warranted should a subclad cracking prone forging ever in the future be subjected to very high embrittlement levels.

B-11

The subclad flaws for the sensitivity study of Table 1 assigned half of the flaws to have depths of 4 percent of the vessel wall thickness and the remaining flaws to have depths of 2 percent of the vessel wall thickness. Calculations for these flaw depths predicted substantial contributions from subclad flaws, whereas other calculations (not reported in NUREG-1808) for a bounding flaw depth of 2 percent of the vessel wall predicted small contribution of subclad flaws to vessel failure frequencies.

It is noted here that the flaw input files used for the ORNL/NRC flaw sensitivity calculations had an error that understated the estimated number of subclad flaws by a factor of about 25. Details of this error and the correction of this problem are described below. The net effect would tend to underestimate the effects of subclad flaws on calculated failure frequencies for embrittled forged vessels.

Table 1 Results of Subclad Crack Sensitivity Study Forging TWCF Forging FCI Ratio Base Subclad Ratio EFPY Base FCI Subclad Subclad TWCF Flaws Subclad FCI /Base TWCF /Base 32 1.56E-7 1.60E-8 0.10 1.40E-9 2.57E-12 0.0018 60 5.66E-7 9.60E8 0.17 6.15E-9 1.09E-9 0.18 Ext-Bb 9.00E-6 1.31E-5 1.46 3.81E7 3.95E-6 10.37 The baseline for all analyses was Beaver Valley as reported by [EricksonKirk, 2004b].

Proposed Flaw Distribution Model The updated flaw distribution model includes:

1. a correction to the equation that converts flaw density from flaws per unit area to flaws per unit volume of vessel material
2. changes to parameters of the flaw distribution using insights from the literature review along with a treatment of the uncertainties in estimating these parameters The proposed model has been implemented into the PNNL flaw distribution algorithm. The results of example calculations are described below. The discussion concludes with recommendations for further development of the model.

Corrections for Flaw Density PNNL determined that flaw input files used for the ORNL/NRC flaw sensitivity had an error that understated the number of subclad flaws by a factor of about 25. An error was made in converting flaw rates from flaws per unit area of vessel surface to an equivalent number of flaws per unit volume of forging material. The effect of the underestimated flaw densities has not been evaluated by comparison calculations with the FAVOR code. However, even the incorrect density assigned a very large number of subclad flaws, such that each sub-region of the vessel inner surface was predicted to have several subclad flaws. Whereas predicted failure frequencies are in most cases roughly proportional to the number of flaws in the vessel, this trend should saturate at very high levels of flaw density. In this case, all regions of the vessel with lower bound toughness levels will have one or more subclad flaws of bounding size.

The primary conclusion drawn from the results of Table 1 should not change for a corrected version of the flaw input file. That is, subclad flaws can substantially increase failure frequencies for embrittled forged vessels, and more detailed evaluations should be performed if such vessels become of concern to future vessel integrity evaluations.

B-12

Flaw Distribution Parameters This section describes a proposed model for subclad cracks in the beltline regions of reactor pressure vessels. The model is based on the information described above and also addresses uncertainties in knowledge of the underclad cracks that could exist in a specific vessel. The model includes the following parameters:

1. flaw frequency expressed in terms of flaws per unit area of the vessel inner surface
2. the maximum (or bounding) through-wall depth dimension of the subclad flaws
3. the conditional distribution of the through-wall depth dimensions expressed as a fraction of the bounding depth dimension
4. the conditional distribution of the length dimensions of the subclad flaws It is assumed that vessel specific evaluations have been performed based on considerations of material/welding parameters (and possibly of inspection findings) to establish whether there is a potential for subclad cracking for the vessel of concern. For purposes of the preliminary model, this occurrence probability has been assigned to be one. As the flaw distribution model is further refined, expert judgment could be applied to better estimate a probability of subclad cracking for each given vessel.

Maximum Through-Wall Dimensions of CracksThis parameter defines the bounding depth dimension for the subclad cracks in a given simulated vessel. As described below, a conditional depth distribution is also defined for the individual cracks. The conditional depth distribution is truncated at the bounding crack depth. The model features a bounding flaw depth dimension for each simulated vessel. This bounding depth is assumed to be related to details of the cladding procedure (e.g., heat inputs for the welding process) along with the susceptibility of the vessels forging material to subclad cracking (e.g.,

the chemistry of the vessel specific heat of material).

Figure 4 shows the assumed distribution function for the bounding flaw depth dimension. Vessel-to-vessel variability for the bounding crack depth is addressed by using the French work (Pellissier Tanon et al., 1990; Buchalet et al., 1990; ASME, 1993; Moinereau et al., 2001) and the paper by Dolby and Saunders (1977) for guidance. On this basis, the probability for the maximum depth being greater than 3 mm is assigned to be less than 10-1 (envelope defect of Figure 3), and the probability of the defect being greater than 6 mm is assigned to be two orders of magnitude less (less than 10-3 for the exceptional defect of Figure 3). The distribution of bounding flaw depths (Figure 4) is described by uniform distribution of the logarithm of the probability over the range of 0-6 mm.

1.E+01 Probability Greater Than Depth 1.E+00 1.E-01 1.E-02 1.E-03 1.E-04 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 Bounding Flaw Depth, mm Figure 4 Probabilities for Bounding Depth of Subclad Flaws B-13

Conditional Flaw Depth DistributionThe conditional distribution of depth dimensions of subclad flaws for a given vessel is assumed to be relatively uniform and is described by a uniform distribution over the range of 50 percent to 100 percent of the bounding size as shown by Figure 5. This assumption is the same as for the prior input files provided to ORNL/NRC for the sensitivity calculations for subclad flaws.

The uniform distribution is a reflection of the lack of information on measured flaw depth dimensions.

The approach therefore conservatively assigns a large fraction of the flaws to have depth dimensions equal to about the bounding dimension.

1.2 1.0 Probability Greater Than Depth 0.8 0.6 0.4 0.2 0.0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 Flaw Depth/Bounding Flaw Depth Figure 5 Conditional Depth Distributions of Subclad Flaws Maximum Length Dimensions of CracksThe envelope and exceptional defects of Figure 3 were first considered the basis for a conditional distribution for flaw length dimensions. With this approach, the probability of a defect with a 60-mm length would be assigned as 10-2 for both a 3-mm and 6-mm bounding depth of flaw. This approach (based on the 60-mm length) would be significantly more conservative than that for the prior flaw input files of the ORNL/NRC sensitivity calculations for subclad flaws. The French publications provide no data or rationale for the 60-mm flaw length, whereas other publications show subclad flaws (see Figure 1) that have lengths much less than 60 mm. Furthermore, discussions of the mechanisms of subclad cracking state that flaws are confined to the overlap region of the heat-affected zones of adjacent passes of the strips of cladding. This mechanistic model would also give flaw lengths much less than the 60-mm (2.4-inch) flaw of the French publications.

The length distribution of Figure 6 as adopted for the updated model was the same as that assumed for the prior ORNL/NRC sensitivity calculations. A uniform distribution was used to simulate the numerical differences between the flaw length and depth dimensions. The uniform distribution ranged from 0 mm to 5 mm. For each category (or bin) of the flaw depth dimension, the generated input files for FAVOR have a distribution table for flaw aspect ratios.

Number of Cracks per Unit Area of Vessel Inner SurfaceThe past PNNL estimate for the frequency of underclad cracks was 80,512 flaws per square meter. This density was derived from an analysis of the flaws shown in Figure 1, which was then assumed to depict a region of a vessel surface with a severe case of subclad cracking. This density was treated as a conservative or upper bounding estimate of the flaw occurrence frequency with the lower bound assigned to an order of magnitude less as a lower bound estimate. It was assumed that the distribution function was a uniform distribution for the logarithm of the flaw frequency between these bounding values. Figure 7 shows the resulting distribution of flaw frequency.

B-14

1.2 1.0 Probability Greater Than Value 0.8 0.6 0.4 0.2 0.0 0 1 2 3 4 5 Flaw Length minus Flaw Depth, mm Figure 6 Conditional Distributions for Flaw Length 1.2 Probability Greater Than Density 1.0 0.8 0.6 0.4 0.2 0.0 0 20,000 40,000 60,000 80,000 100,000 Flaws per Square Meter Figure 7 Flaw Frequency Distribution Example Calculations The proposed flaw distribution model was implemented into a computer program, and an output file is provided as an appendix to this report. This output has results for the first 10 of the 1000 simulated vessels that are addressed by the full input file for the FAVOR code. Significant differences were seen in the predicted flaw distributions compared to the prior PNNL work. A large part of these differences came from correcting the original conversion from flaws per unit area to flaws per unit volume.

Table 2 summarizes results from both the prior model (Tables 2a through 2d) and the updated model (Tables 2e and 2f). Results are presented both in terms of flaw density (flaws per cubic foot) and total number of flaws in a vessel considering only the beltline region (assuming a surface area of 627 square feet corresponding to a vessel in a typical FAVOR calculation). The flaws are further categorized in terms of their through-wall depth dimensions (0-2 mm, 2-4 mm, and 4-6 mm). Table 2 shows very large numbers for subclad flaws, ranging up to a few million flaws per vessel. This means that if even a small fraction of the vessel inner surface is exposed to the peak levels of embrittling neutron fluence, these local regions will still have thousands of subclad flaws. It is therefore expected that the effect of flaw density B-15

on vessel failure frequency will become insensitive to flaw density. Failure frequency will then become more sensitive to the simulated bounding sizes of the subclad flaws.

Table 2(f) illustrates some significant aspects of the new proposed model relative to the prior model. For example, only vessel #8 of the first 10 simulated vessels has any flaws with depth dimensions greater than 2 mm. The sensitivity calculations performed by ORNL with FAVOR predicted zero failure probability for a 2-mm flaw depth, even though many 2-mm flaws were present in the beltline regions. Therefore, only 1 of the 10 vessels of Table 5(f) would have a 2-4 mm flaw, and only these vessels would be expected to fail. In contrast, for the prior flaw distribution of Table 2(d), all vessels had many 4-mm flaws, and a large fraction of the simulated vessels were predicted to fail.

B-16

Table 2 Summary of Results for Subclad FlawsPrior Model Versus Proposed Model (a) Prior Model - Uncorrected Values (Flaws per Cubic Foot)

Flaw Depth Dimension Total 0-2 mm 2-4 mm 4-6 mm 456 233 223 0 (b) Prior Model - Uncorrected Values (Flaws per Vessel)

Flaw Depth Dimension Total 0-2 mm 2-4 mm 4-6 mm 190,608 97,394 93,214 0 (c) Prior Model - Corrected Values (Flaws per Cubic Foot)

Flaw Depth Dimension Total 0-2 mm 2-4 mm 4-6 mm 10,958 5,599 5,359 0 (d) Prior Model - Corrected Values (Flaws per Vessel)

Flaw Depth Dimension Total 0-2 mm 2-4 mm 4-6 mm 4,580,310 2,340,378 2,239,932 0 (e) Proposed Model (Flaws per Cubic Foot)

Flaw Depth Dimension Total 0-2 mm 2-4 mm 4-6 mm Average of 1000 Vessels 6,329 5,444 850 35 Vessel #1 5,580 5,580 0 0 Vessel #2 10,701 10,701 0 0 Vessel #3 4,272 4,272 0 0 Vessel #4 8,312 8,312 0 0 Vessel #5 2,554 2,554 0 0 Vessel #6 10,615 10,615 0 0 Vessel #7 6,351 6,351 0 0 Vessel #8 1,784 1,606 178 0 Vessel #9 1,190 1,190 0 0 Vessel #10 7,718 7,718 0 0 (f) Proposed Model (Flaws per Vessel)

Flaw Depth Dimension Total 0-2 mm 2-4 mm 4-6 mm Average of 1000 Vessels 2,645,522 2,275,592 355,300 14,630 Vessel #1 2,332,440 2,332,440 0 0 Vessel #2 4,473,018 4,473,018 0 0 Vessel #3 1,785,696 1,785,696 0 0 Vessel #4 3,474,416 3,474,416 0 0 Vessel #5 1,067,572 1,067,572 0 0 Vessel #6 4,437,070 4,437,070 0 0 Vessel #7 2,654,718 2,654,718 0 0 Vessel #8 745,712 671,308 74,404 0 Vessel #9 497,420 497,420 0 0 Vessel #10 3,226,124 3,226,124 0 0 B-17

References ASME. 1993. White Paper on Reactor Vessel Integrity Requirements for Level A and B Conditions, EPRI TR-100251, prepared by ASME Section XI Task Group on Reactor Pressure Vessel Integrity Requirements, prepared for ASME Section XI Working Group on Operating Plant Criteria, published by Electric Power Research Institute.

Ayres, P.S., et al. 1972. Babcock and Wilcox, Topical Report, BAW-10012-A, October 1972.

Bamford, W., and R.D. Rishel. 2000. A Review of Cracking Associated with Weld Deposited Cladding in Operating PWR Plants, WCAP-15338, Westinghouse Electric Company, Pittsburgh, Pennsylvania, March 2000.

Buchalet, C., W.L. Server, and T.J. Griesbach. 1990. U.S. and French Approaches to Reactor Vessel Integrity, prepared for the 1990 ASME Pressure Vessel and Piping Conference, Nashville, Tennessee, June 1990.

Canonico, D.A. 1977. Significance of Reheat Cracks to the Integrity of Pressure Vessels for Light-Water Reactors, ORNL/NUREG-15, prepared by Oak Ridge National Laboratory for the NRC.

Canonico, D.A. 1979. Significance of Reheat Cracks to the Integrity of Pressure Vessels for Light-Water Reactors, Welding Research Supplement to the Welding Journal, May 1979.

Chapman, O.J.V., and F.A. Simonen. 1998. RR-PRODIGALA Model for Estimating the Probabilities of Defects in Reactor Pressure Vessel Welds, NUREG/CR-5505, prepared by Pacific Northwest Laboratory the NRC, October 1998.

Dhooge, A., R.E. Dolby, J. Sebille, R. Steinmetz, and A.G. Vinckier. 1978. A Review of Work Related to Reheat Cracking in Nuclear Reactor Pressure Vessel Steels, International Journal of Pressure Vessels and Piping, Vol. 6, 1978, pp. 329-409.

Dolby, R.E., and G.G. Saunders. 1977. Underclad Cracking in Nuclear Vessel SteelsPart 1 Occurrence and Mechanism of Cracking, Metal Construction, Vol. 9, No. 12, pp. 562-566, December 1977.

Dolby, R.E., and G.G. Saunders. 1978. Underclad Cracking in Nuclear Vessel SteelsPart 2 Detection and Control of Underclad Cracking, Metal Construction, Vol. 9, No. 12, pp. 20-24, January 1978.

Dumont, P., M. Bieth, and J.P. Launay. 1987. French Developments in the Ultrasonic Examination of Pressure Vessels, International Journal of Pressure Vessels and Piping, Vol. 28, pp. 19-23.

EricksonKirk, M., et al. 2004. Technical Basis for Revision of the Pressurized Thermal Shock (PTS)

Screening Limit in the PTS Rule (10 CFR 50.61): Summary Report, NUREG-1806.

EricksonKirk, M., T. Dickson, T. Mintz, and F. Simonen. 2004. Sensitivity Studies of the Probabilistic Fracture Mechanics Model Used in FAVOR, NUREG-1808 (available Febuary 2010).

Frederick, G., and P. Hernalsteen. 1981. Underclad Cracking in PWR Reactor Vessels, AIM International Meeting: Modern Electric Power Stations, Liege, Paper 20.

Gonnet, B. 1982. How Framatome Has Dealt with the Cracking Problem, Nuclear Engineering International, Vol. 27, No. 322, January 1982, pp. 21-24.

Horiya, T., T. Takeda, and K. Yamata. 1985. Study of Underclad Cracking in Nuclear Reactor Vessel Steels, ASME Journal of Pressure Vessel Technology, Vol. 107, February 1985, pp. 30-35.

Jackson, D.A., and L. Abramson. 2000. Report on the Preliminary Results of the Expert Judgment Process for the Development of a Methodology for a Generalized Flaw Size and Density Distribution for Domestic Reactor Pressure Vessels, MEB-00-01, PRAB-00-01, NRC, September 2000.

B-18

Lauerova, D., M. Brumovsky, P. Simpanen, and J Kohopaa. 2003. Problems of Underclad Type Defects in Reactor Pressure Vessel Integrity Evaluation, Transactions of the 17th International Conference on Structural Mechanics in Reactor Technology (SMIT 17), Paper #G02-2, Prague, Czech Republic, August 17-22, 2003.

Lopez, H.F. 1987. Underclad Cracking of Pressure Vessel Steels for Light-Water Reactors, Scripta Metallurgica, Vol. 21, pp. 753-758.

Mager, T.R., B. Landerman, and Kubit. 1971. Reactor Vessels and Weld Cladding, Westinghouse Electric, WCAP-7733, July 1971.

Moinereau, D., G. Bezdikian, and C. Faidy. 2001. Methodology for the Pressurized Thermal Shock Evaluation: Recent Improvements in French RPV PTS Assessment, International Journal of Pressure Vessels and Piping, Vol. 78, pp. 69-83.

Pellissier Tanon, A., J. Grandemange, B. Houssin, and C. Buchalet. 1990. French Verification of PWR Vessel Integrity, EPRI NP-6713, prepared by Framatome, Paris, France, for Electric Power Research Institute, February 1990.

Simonen, F.A. 1994. Meeting MinutesNRC Flaw Distribution WorkshopDecember 7-8, 1994, Rockville, Maryland, prepared for the NRC by Pacific Northwest National Laboratory.

Simonen, F.A. 1996. Meeting MinutesNRC Meeting on Clad Region FlawsJuly 29-30, 1996, Rockville, Maryland, prepared for the NRC by Pacific Northwest National Laboratory.

NRC. 2002a. Information Supporting WOG Request for Modification of NRC Safety Evaluation of WCAP-15338, NRC, June 2002.

NRC. 2002b. Safety Evaluation of the Office of Nuclear Reactor Regulation Topical Report WCAP-15338A Review of Cracking Associated with Weld Deposited Cladding in Operating Pressurized Water Reactor (PWR) Plants Westinghouse Owners Group, NRC, September 25, 2002.

NRC. 1972. Control of Stainless Steel Weld Cladding of Low-Alloy Steel Components, Regulatory Guide 1.43.

NRC. 2002. Information Supporting WOG Request for Modification of NRC Safety Evaluation of WCAP-15338, NRC, June 2002.

NRC. 2002. Safety Evaluation of the Office of Nuclear Reactor Regulation Topical Report WCAP-15338A Review of Cracking Associated with Weld Deposited Cladding in Operating Pressurized Water Reactor (PWR) Plants Westinghouse Owners Group, NRC, September 25, 2002.

Vinckier, A.G., and A.W. Pense. 1974. A Review of Underclad Cracking in Pressure-Vessel Components, Welding Research Council Bulletin No. 197, Welding Research Council, New York, August 1974.

Wilkie, T. 1980. Cracks in French Pressure Vessels Pose no Danger, Nuclear Engineering International, Vol. 25, No. 294, January 1982, pp. 27-29.

B-19

Example Output from Proposed Subclad Model GENERATION OF FLAW DISTRIBUTION INPUT FILE FOR THE ORNL FAVOR CODE NAME OF REGION = SUBCLAD FLAWS JANUARY 3, 2005 WELD FLAW/FT^3 PVRUF BEAVER VALLEY NUMBER OF SUBREGIONS = 1 UNCERTAINTY CALCULATION NUMBER OF MONTE CARLO SIMULATIONS = 1000 VESSEL TOTAL WALL THICKNESS (MM) = 203.99 ENGLISH UNITS - FLAWS PER FT^2 OR FLAWS PER FT^3 WELD DENSITY OPTION - FLAWS PER UNIT VOLUME BASE_METAL APPROXIMATION NOT USED OUTPUT FILE REFORMATED FOR INPUT TO ORNL FAVOR CODE SUBREGION NUMBER 1 VOLUME FRACTION = 1.0000 PVRUF VESSEL PARAMETERS SAW (SUBMERGED METAL ARC WELD)

BEAD SIZE (MM) = 4.76 FACTOR ON FLAW FREQUENCIES = 1.0000 (DEFAULT = 1.0)

CLAD THICKNESS(MM) = .0000 (USED ONLY FOR CLAD)

CLAD BEAD WIDTH (MM) = .0000 (USED ONLY FOR CLAD)

NUMBER OF CLAD LAYERS = 0 (USED ONLY FOR CLAD)

TRUNCATION ON FLAW DEPTH (MM) = 100.0000 B-20

FLAW DISTRIBUTION FOR SIMULATION NUMBER 1 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .55808E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-21

FLAW DISTRIBUTION FOR SIMULATION NUMBER 2 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .10701E+05 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-22

FLAW DISTRIBUTION FOR SIMULATION NUMBER 3 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .42724E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-23

FLAW DISTRIBUTION FOR SIMULATION NUMBER 4 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .83129E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-24

FLAW DISTRIBUTION FOR SIMULATION NUMBER 5 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .25543E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-25

FLAW DISTRIBUTION FOR SIMULATION NUMBER 6 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .10615E+05 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-26

FLAW DISTRIBUTION FOR SIMULATION NUMBER 7 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .63516E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-27

FLAW DISTRIBUTION FOR SIMULATION NUMBER 8 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .16060E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .17877E+03 19.124 19.124 38.248 23.504 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-28

FLAW DISTRIBUTION FOR SIMULATION NUMBER 9 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .11909E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-29

FLAW DISTRIBUTION FOR SIMULATION NUMBER 10 N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .77182E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-30

LARGEST OF EACH ELEMENT FOR 1000 SIMULATIONS N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .11167E+05 100.000 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .10106E+05 100.000 19.124 38.248 23.504 .000 .000 .000 .000 .000 .000 .000 3 .61631E+04 100.000 31.873 36.253 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-31

MEDIAN OF EACH ELEMENT FOR 1000 SIMULATIONS N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .53317E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-32

MEAN OF EACH ELEMENT FOR 1000 SIMULATIONS N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .54444E+04 8.247 6.247 12.494 24.989 24.989 23.034 .000 .000 .000 .000 .000 2 .84989E+03 76.707 5.508 11.015 6.769 .000 .000 .000 .000 .000 .000 .000 3 .35210E+02 98.637 .637 .725 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 99.999 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-33

SMALLEST OF EACH ELEMENT FOR 1000 SIMULATIONS N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .00000E+00 6.375 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 2 .00000E+00 19.124 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 31.873 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-34

25TH PERCENTILE OF EACH ELEMENT FOR 1000 SIMULATIONS N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .27131E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 19.124 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-35

75TH PERCENTILE OF EACH ELEMENT FOR 1000 SIMULATIONS N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .80896E+04 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .37132E+03 100.000 19.124 38.248 23.504 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-36

5TH PERCENTILE OF EACH ELEMENT FOR 1000 SIMULATIONS N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .92667E+03 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .00000E+00 19.124 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-37

95TH PERCENTILE OF EACH ELEMENT FOR 1000 SIMULATIONS N FLAWS/FT**3 1.0-1.25 1.25-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.0 6.0-8.0 8.0-10.0 10.0-15.0 >15.0 1 .10661E+05 6.375 6.375 12.749 25.499 25.499 23.504 .000 .000 .000 .000 .000 2 .51625E+04 100.000 19.124 38.248 23.504 .000 .000 .000 .000 .000 .000 .000 3 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 4 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 5 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 6 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 7 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 8 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 9 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 10 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 11 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 12 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 13 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 14 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 15 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 16 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 17 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 18 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 19 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 20 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 21 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 22 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 23 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 24 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 25 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 26 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 27 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 28 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 29 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 30 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 31 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 32 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 33 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 34 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 35 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 36 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 37 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 38 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 39 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 40 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 41 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 42 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 43 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 44 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 45 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 46 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 47 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 48 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 49 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 50 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 51 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 52 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 53 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 54 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 55 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 56 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 57 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 58 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 59 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 60 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 61 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 62 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 63 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 64 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 65 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 66 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 67 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 68 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 69 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 70 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 71 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 72 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 73 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 74 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 75 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 76 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 77 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 78 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 79 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 80 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 81 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 82 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 83 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 84 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 85 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 86 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 87 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 88 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 89 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 90 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 91 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 92 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 93 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 94 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 95 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 96 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 97 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 98 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 99 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 100 .00000E+00 100.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 B-38

APPENDIX C SENSITIVITY STUDY ON AN ALTERNATIVE EMBRITTLEMENT TREND CURVE

Sensitivity Study on an Alternative Embrittlement Trend Curve Subsequent to the development of FAVOR Version 06.1 as per the change specification in Appendix A, Eason developed an alternative embrittlement trend curve of a slightly simplified form (Eason 07). This alternative relationship is very similar in form to that which appears as Eq. 3-4 in the main text of this report, and is provided below for reference.

Eq. C-1 T30 MD CRP MD A1 0.001718TRCS 1 6.13PMn 2.47 te CRP B 1 3.77 Ni 1.191 f Cu , P g Cu , Ni, t e e e 1.140 x10 7 for forgings A 1.561x10 7 for plates 1.417 x10 7 for welds 102.3 for forgings 102.5 for plates in non - CE manufactured vessels B

135.2 for plates in CE manufactured vessels 155.0 for welds t for 4.39 1010 t e 4.39 10 10 0.2595 10 t

for 4.39 10 Note: Flux () is estimated by dividing fluence (t) by the time (in seconds) that the reactor has been in operation.

log t 1.139Cu e 0.448 Ni 18.120 g Cu e , Ni, t e tanh 10 e 1 1 2 2 0.629 0 for Cu 0.072 f Cu e , P Cu e 0.072 for Cu 0.072 and P 0.008 0.668 Cu 0.072 1.359( P - 0.008)0.668 for Cu 0.072 and P 0.008 e

0 for Cu 0.072 wt%

Cu e minCu , MaxCu e for Cu 0.072 wt%

Max(Cu e ) 0.243 for Linde 80 welds, and 0.301 for all other materials.

Since FAVOR 06.1 had been coded and the through-wall cracking frequency (TWCF) values reported in Table 3.1 had been calculated before the development of Eq. C-1 there was a need to assess the effect, if any, of using Eq. C-1 instead of Eq. 3-4 in the FAVOR calculations. Eq. C-1 was therefore coded into C-1

FAVOR, and four different embrittlement conditions, as summarized in Table C.1, were analyzed. In Figure C.1, the TWCF and reference temperature (RT) values from Table C.1 are compared to the baseline results from FAVOR 06.1 (Figure 3.4). This comparison shows that changing from the Eq. 3-4 to the Eq. C-1 trend curve does not produce any significant effect on the TWCF values estimated by FAVOR and, consequently, has no significant effect on the TWCF and RT screening limits proposed in the main body of this report.

Table C.1. FAVOR TWCF Results Using Eq. F-1 for the Embrittlement Trend Curve RT Values [oF]  % TWCF due to 95th Percentile TWCF Condition Axial Circ RTAW- RTPL- RTCW- Plate Axial Weld Weld Total Plate Circ Weld MAX MAX MAX Flaws Weld Flaws Flaws BV200 251 339 339 21.77 66.79 11.44 2.82E-06 6.14E-07 1.88E-06 3.23E-07 PAL 500 421 391 397 97.42 2.35 0.23 9.09E-05 8.86E-05 2.14E-06 2.09E-07 OCO32 160 74 179 100.00 0.00 0.00 2.16E-15 2.16E-15 0 0 OCO1000 294 205 322 99.12 0.28 0.60 3.69E-07 3.66E-07 1.03E-09 2.21E-09 C-2

1.E-03 1.E-03 1.E-03 August 2006 August 2006 Beaver 1.E-04 FAVOR 06.1 1.E-04 FAVOR 06.1 1.E-04 Oconee 95 %ile TWCF - Axial Weld Flaws 95 %ile TWCF - Circ Weld Flaws 1.E-05 1.E-05 1.E-05 95 %ile TWCF - Plate Flaws Palisades 1.E-06 1.E-06 1.E-06 Fit 1.E-07 1.E-07 1.E-07 Alternate Trend Curve 1.E-08 1.E-08 1.E-08 1.E-09 1.E-09 1.E-09 1.E-10 Beaver 1.E-10 1.E-10 Beaver 1.E-11 Oconee 1.E-11 1.E-11 Oconee 1.E-12 Palisades th 1.E-12 Palisades 1.E-12 th th 1.E-13 Fit 1.E-13 Fit 1.E-13 Alternate August 2006 1.E-14 1.E-14 Alternate 1.E-14 Trend Curve FAVOR 06.1 Trend Curve 1.E-15 1.E-15 1.E-15 550 650 750 850 550 650 750 850 550 650 750 850 Max. RT AW [R] Max. RT PL [R] Max RT CW [R]

Figure C.1. FAVOR 06.1 baseline results from Figure 3.4 compared with TWCF values estimated using Eq. C-1 (red circles)

C-3

C-4 APPENDIX D TECHNICAL BASIS FOR THE INPUT FILES TO THE FAVOR CODE FOR FLAWS IN VESSEL FORGINGS

Technical Basis for the Input Files to the FAVOR Code for Flaws in Vessel Forgings F.A. Simonen Pacific Northwest National Laboratory Richland, Washington July 28, 2004 Pacific Northwest National Laboratory (PNNL) has been funded by the U.S. Nuclear Regulatory Commission (NRC) to generate data on fabrication flaws that exist in reactor pressure vessels (RPVs).

Work has focused on flaws in welds, but with some attention also to flaws in the base metal regions.

Data from vessel examinations, along with insights from an expert judgment elicitation (MEB-00-01) and from applications of the PRODIGAL flaw simulation model (NUREG/CR-5505, Chapman et al., 1998),

have been used to generate input files (see NUREG/CR-6817, Simonen et al., 2003) for probabilistic fracture mechanics calculations performed with the FAVOR code by Oak Ridge National Laboratory.

NUREG/CR-6817 addresses only flaws in plate materials and provided no guidance for estimating the numbers and sizes of flaws in forging materials. More recent studies have examined forging material, which has provided data on flaws that were detected and sized in the examined material. At the request of NRC staff, PNNL has used these more recent data to supplement insights from the expert judgment elicitation to generate FAVOR code input files for forging flaws. The discussion below describes the technical basis and results for the forging flaw model.

Nature of Base Metal Flaws PNNL examined material from some forging material from a Midland vessel as described by Schuster (2002). The forging was made during 1969 by Ladish. Examined material included only part of the forging that had been removed from the top of the forged ring as scrap not intended for the vessel. This material was expected to have more than the average flaw density, and as such may contribute to the conservatism of any derived flaw distribution.

Figures 1 and 2 show micrographs of small flaws in plate and forging materials. These flaws are inclusions rather than porosity or voids. They are also not planar cracks. Therefore, their categorization as simple planar or volumetric flaws is subject to judgment. The plate flaw of Figure 1 has many sharp and crack-like features, whereas such features are not readily identified for the particular forging flaw seen in Figure 2. It should, however, be emphasized that the PNNL examined only a limited volume of both plate and forging material and found very few flaws in examined material. It is not possible to generalize from such a small sample of flaws. Accordingly, the flaw model makes assumptions that may be somewhat conservative, due to the limited data on the flaw characteristics.

Flaw Model for Forging Flaws The model for generating distributions of forging flaws for the FAVOR code uses the same approach as that for modeling plate flaws as described in NUREG/CR-6817. The quantitative results of the expert elicitation are used along with available data from observed forging flaws. The flaw data were used as a sanity check on the results of the expert elicitation. Figure 3 summarizes results of the expert elicitation. Each expert was asked to estimate ratios between flaw densities in base metal compared to the corresponding flaw densities observed in the weld metal of the PVRUF vessel. Separate ratios were requested for plate material and forging material.

D-1

As indicated in Figure 3, the parameters for forging flaws are similar to those for plate flaws. The forging and plate models used the same factor of 0.1 for the density of small flaws (flaws with through-wall dimensions less than the weld bead size of the PVRUF vessel). The density of large flaws in forging material is somewhat greater than the density of flaws in plate material. The factor of 0.025 for the flaw density is replaced by a factor of 0.07 for forging flaws. A truncation level of 0.11 mm is used for both plate and forging flaws. As described in the next section, the data from forging examinations show that these factors are consistent with the available data. It is noted that the assumption for the 0.07 factor is supported by only a single data point corresponding to the largest observed forging flaw (with a depth dimension of 4 mm).

The factors of 0.1 and 0.07 came from the recommendations from the expert elicitation on vessel flaws.

As noted below, the very limited data from PNNLs examinations of forging material show that these factors are consistent with the data, although the 0.07 factor is supported by only one data point for an observed forging flaw with a 4-mm depth dimension.

Comparison with Data on Observed Flaws The PNNL examinations of vessel materials included both plate materials and forging materials. For plate flaws less than 4 mm in through-wall depth dimension, Figure 4 shows data from NUREG/CR-6817 that show frequencies for plate flaws. Also shown for comparison are the flaw frequencies for the welds of the PVRUF and Shoreham vessels. This plot confirmed results of the expert judgment elicitation (Figure 4) and indicated (1) there are fewer flaws in plate material than in weld material, and (2) there is about a 10:1 difference in flaw frequencies for plates versus welds.

PNNL generated the data on flaws in forgings after preparation of NUREG/CR-6817. Forging data are presented in Figures 5 and 6 along with the previous data for flaws in the PVRUF plate material. There is qualitative agreement with the results of the expert judgment elicitation (Figure 4), which indicates that (1) plate and forging materials have similar frequencies for small (2 mm) flaws, and (2) forging material have higher flaw frequencies for larger (> 4 mm) flaws.

Inputs for FAVOR Code Figure 7 compares the flaw frequencies for plates and forgings that were provided to ORNL as input files for the FAVOR code. This plot shows mean frequencies from an uncertainty distribution as described by the flaw input files. It is seen that the curves for plate and forging flaws are identical for small flaws, but show differences for the flaws larger than 3% of the vessel wall thickness. Also seen is the effect of truncating the flaw distribution at a depth of 11 mm (about 5% of the wall thickness).

D-2

References Jackson, D.A., and L. Abramson, 2000. Report on the Preliminary Results of the Expert Judgment Process for the Development of a Methodology for a Generalized Flaw Size and Density Distribution for Domestic Reactor Pressure Vessel, MED-00-01, PRAB-00-01, U.S. Nuclear Regulatory Commission.

Schuster, G.J., 2002. Technical Letter ReportJCN-Y6604Validated Flaw Density and Distribution Within Reactor Pressure Vessel Base Metal Forged Rings, prepared by Pacific Northwest National Laboratory for U.S. Nuclear Regulatory Commission, December 20, 2002.

Simonen, F.A., S.R. Doctor, G.J. Schuster, and P.G. Heasler, 2003. A Generalized Procedure for Generating Flaw-Related Inputs for the FAVOR Code, NUREG/CR-6817, Rev. 1, prepared by Pacific Northwest National Laboratory for U.S. Nuclear Regulatory Commission.

Figure 1 Small Flaw in Plate Material Figure 2 Small Flaw in Forging Material D-3

Figure 3 Relative Flaw Densities of Base Metal Compared to Weld Metal as Estimated by Expert Judgment Process (from Jackson and Abramson, 2000) 100,000 C:\FLAWDATA\ORNL-FLAW-002.XLS PVRUF Base Metal Flaw Rate- per cubic meter 10,000 Average of Base Metal Hope Creek 1,000 PVRUF Weld Shoreham Weld 100 Shoreham River Bend Base Metal Base Metal 10 1

0 2 4 6 8 10 12 14 Flaw Depth, mm Figure 4 Flaw Frequencies for Plate Materials with Comparisons to Data for Weld Flaws D-4

1.E+04 Cumulative Density 1.E+03 (per cubic meter) 1.E+02 0 1 2 3 4 5 Through-wall size (mm)

PVRUF plate 109-1,2,5 109-1,2 Figure 5 Validated Flaw Density and Size Distribution for Three Forging Specimens (cumulative flaw density is the number of flaws per cubic meter of equal or greater size) 1.E+04 Cumulative Density 1.E+03 (per cubic meter) 1.E+02 0 1 2 3 4 5 6 Through-wall size (mm)

PVRUF plate 109-5 109-1 109-2 Figure 6 Average of Validated Cumulative Flaw Density for Forging Material, A508 D-5

1.E+02 1.E+01 Flaws per Cubic Foot 1.E+00 Forging 1.E-01 Plate 1.E-02 0 1 2 3 4 5 6 Flaw Depth Dimension, Percent of Wall Figure 7 Comparison of Flaw Distributions for Forging and Plate D-6

D-7 NRC FORM 335 U.S. NUCLEAR REGULATORY COMMISSION 1. REPORT NUMBER (9-2004) (Assigned by NRC, Add Vol., Supp., Rev.,

NRCMD 3.7 and Addendum Numbers, if any.)

BIBLIOGRAPHIC DATA SHEET (See instructions on the reverse) NUREG-1874

2. TITLE AND SUBTITLE 3. DATE REPORT PUBLISHED Recommended Screening Limits for Pressurized Thermal Shock (PTS) MONTH YEAR March 2010
4. FIN OR GRANT NUMBER
5. AUTHOR(S) 6. TYPE OF REPORT 1 2 M.T. EricksonKirk and T.L. Dickson Technical
7. PERIOD COVERED (Inclusive Dates) 1-2005 to 2-2007
8. PERFORMING ORGANIZATION - NAME AND ADDRESS (If NRC, provide Division, Office or Region, U.S. Nuclear Regulatory Commission, and mailing address; if contractor, provide name and mailing address.)

1 Division of Fuel, Engineering, and Radiological Research, Office of Nuclear Regulatory Research, U.S. Nuclear Regulatory Commission, Washington, DC 20555-0001 2

Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6075

9. SPONSORING ORGANIZATION - NAME AND ADDRESS (If NRC, type "Same as above"; if contractor, provide NRC Division, Office or Region, U.S. Nuclear Regulatory Commission, and mailing address.)

Division of Fuel, Engineering, and Radiological Research, Office of Nuclear Regulatory Research, U.S. Nuclear Regulatory Commission, Washington, DC 20555-0001

10. SUPPLEMENTARY NOTES
11. ABSTRACT (200 words or less)

During plant operation, the walls of reactor pressure vessels (RPVs) are exposed to neutron radiation, resulting in localized embrittlement of the vessel steel and weld materials in the core area. If an embrittled RPV had a flaw of critical size and certain severe system transients were to occur, the flaw could very rapidly propagate through the vessel, resulting in a through-wall crack and challenging the integrity of the RPV. The severe transients of concern, known as pressurized thermal shock (PTS),

are characterized by a rapid cooling (i.e., thermal shock) of the internal RPV surface in combination with repressurization of the RPV. Advancements in our understanding and knowledge of materials behavior, our ability to realistically model plant systems and operational characteristics, and our ability to better evaluate PTS transients to estimate loads on vessel walls led the U.S.

Nuclear Regulatory Commission (NRC) to realize that the earlier analysis, conducted in the course of developing the PTS Rule in the 1980s, contained significant conservatisms.

This report provides two options for using the updated technical basis described herein to develop PTS screening limits.

Calculations reported herein show that the risk of through-wall crackin is low in all operating pressurized-water reactors, and current PTS regulations include consderble implicit margin.

12. KEY WORDS/DESCRIPTORS (List words or phrases that will assist researchers in locating the report.) 13. AVAILABILITY STATEMENT Pressurized thermal shock, reactor pressure vessel, probabilistic fracture mechanics unlimited
14. SECURITY CLASSIFICATION (This Page) unclassified (This Report) unclassified
15. NUMBER OF PAGES
16. PRICE NRC FORM 335 (9-2004) PRINTED ON RECYCLED PAPER