ML083190208

Final - Section B Operating Exam (Folder 3)

ML083190208
Person / Time
Site:	Limerick
Issue date:	12/05/2008
From:	Caruso J Operations Branch I
To:	Hunter J Exelon Generation Co
Hansell S
Shared Package
ML081060533	List: ML081840059 ML082890027 ML083181193 ML083181203 ML083181214 ML083181220 ML083190087 ML083190102 ML083190115 ML083190201 ML083190208 ML083190217 ML083220002 ML083520040 ML083650196 ML090260031
References
TAC U01745
Download: ML083190208 (93)

Text

NRC JPM A 2008 Limerick Operating Exam NRC JPM A - 2008 Limerick Operating Test Appendix C Job Performance Measure Form ES-C-I - Worksheet Facility: Limerick Task Title:

Perform Reactor Startup K/A

Reference:

201001 A2.04 (3.8, 3.9) Examinee: Job Performance Measure:

NRC JPM A NRC Examiner:

Date: Method of testins: Simulated Performance: Actual Performance:

X Classroom Simulator X Plant Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied. Initial Conditions:

0 Unit 1 is at 3% power and RPV pressure is 157 psig RPV level is 35 inches, being controlled by LIC-120 in automatic A plant startup is in progress per GP-2, Appendix 1, Reactor Startup and Heatup Control rods are being withdrawn per Control Rod Move Sheet Sequence 1 D:

LGS Sim U-1 .O on Step 17 The next rod move step is to withdraw Control Rod 10-43 There are no channel bow rods Initiating Cue: You are the Reactor Operator.

You have been directed to continue with the startup by withdrawing control rods in accordarice with the control rod move sheet.

Required Materials:

None General

References:

ON-1 07, CRD Problems ARC-MCR-108-F1, CRD Accumulator Trouble ARC-MCR-108-G4, CRD Drive Water Filter Hi Delta P ARC-MCR-108-H4, CRD Charging Water Low Pressure TS 3.1.3.5, Control Rod Scram Accumulators GP2 Appendix 1, Reactor Startup and Heatup, Revision 37 S46.6.C, Placing Alternate Control Rod Water Filter In Service, Revision 08 JPM Origination: New NRC JPM A - 2008 Limerick Operating Test 2 of 11 Appendix C Job Performance Measure Form ES-C-1 Worksheet Task Standard: Address the loss of CRD flow per ON-107 and respond to the subsequent resulting failure of two scram accumulators by tripping the reactor.

Alternate Path: Yes Time Critical: No Validation Time: 15 minutes JPM Setup Instructions: Summary Description of JPM: The applicant will continue the startup by withdrawing control rods per the move sheets.

The CRD drive water hi d/p annunciator will alarm 2 minutes after first rod notch out. The applicant respond per ARC and ON-107 and will direct placing the alternate drive water filter in service. Subsequently, the alternate drive water filter will also clog. During troubleshootinglinitial response, alarms will be received for low CR accumulator pressure.

An EO will be dispatched and will report of low nitrogen pressure in the CR accumulator.

A second accumulator will exhibit the same symptoms shortly thereafter.

The applicant will respond per ON-I07 and ultimately initiate a manual reactor scram. Simulator Setup:

1. 2. 3. 4. 5. 6. Reset to a startup IC at RPV pressure of approximately 157 psig with 1A CRD Pump in operation.

Set up Trigger 1 to activate on depressing Control Rod Notch Out Pushbutton C1 IA- S46 on 1 OC603 Panel (WLCSWDR).

Set up a Manual Trigger 2 to time down for accumulator troubles. Set up to actuate the drive water dip alarm (1 08 G-4) 1 minute after Trigger 1 is activated by closing the running CRD pump discharge valve using the remote function. Set up Malfunction MRC0016C for CR 22-35 Accumulator at 1 minute after Trigger 2 is activated. Set up Malfunction MRCOO16C for CR 46-19 Accumulator at 2minutes 45 seconds after Trigger 2 is activated.

NRC JPM A - 2008 Limerick Operating Test 3 OS11

- Appendix C Job Performance Measure Form ES-C Worksheet Simulator Tables: NRC JPM A - 2008 Limerick Operating Test 4efll Appendix C 2 Form ES-C-1 Performance Information Critical steps denoted with an asterisk Step Element Standard Comment I SatlUnsat NOTCH withdraw control Notch withdraws CRs 10- Note: rods per CR Move Sheet 43, xx-xx and xx-xx from Trigger 1 activates to start 1 Seq 1 D: LGS Sim U-I .O. 04 to 06. CRD trouble timing when notch withdraw Dushbutton is dewessed. Observes indications of Informs supervisor of high Note: high d/p, clogged drive water filter. filter d/p and alarm. CRD Pump discharge valve is closed by remote acknowledged. simulate drive water filter necessary, direct applicant clog.

to resDond to alarm. 2 Cue: Report function on trigger to ___ Refers to ARC-MCR-108- Refers to ARC. Informs G4, CRD Drive Water Filter supervisor of direction to Hi Delta P enter ON-107.

3 Cue: When informed of ARC direction, hand copy of ON-107 to applicant and direct him/her to perform the actions of ON-107. IF lA(B)P158, CRD Pump, is running but CRD drive flow is insufficient, THEN PERFORM one of the following as applicable:

1 2 4* PLACE alternate 1 B(A)F204, CRD Drive Water Filter, in service per S46.6. C.

PLACE alternate FV 1F002B(A), CRD Flow Control Valve, in service per S46.6.

B Directs EO to place alternate drive water filter in service per S46.6.C Booth operator: Respond as EO, obtain S46.6.C. After 1 minute, open discharge valve on running CRD pump (to simulate valving in the alternate drive water filter) and report back that alternate drive water filter is in service. Booth operator:

Aft e r another minute, reclose CRD pump discharge valve on ramp to simulate clogging of alternate drive water filter and initiate trigger to time down to accumulator alarms. NRC JPM A - 2008 Limerick Operating Test 5 of11 Appendix C 2 Form ES-C-1 Performance Information Step Element Standard Comment I SatIUnsat Observes indications of Informs supervisor of high Booth operator: high d/p, clogged drive Report that FIN team is water filter.

aware of filter problem paperwork to replace the filter with hi d/p. filter d/p and alarm. 5 and is expediting Responds to indications of Informs supervisor. Refers Accumulator Trouble.

6 1 St failed accumulator.

to ARC-MCR-108-F1, CRD ARC Actions: Performs ARC actions:

Booth operator: 1. Follow Tech. Spec If directed to investigate, 3.1.3.5, pertaining to Refers to TS report back as EO that control rod scram Dispatches EO to HCU cause of accumulator accumulators.

0 Investigates low N2 trouble is low nitrogen 2. Dispatch Operator to 0 Wtr not suspected pressure.

inspect HCU. 0 Chks spade connectors

3. IF Nitrogen pressure low THEN adjust per 547.8.8 AND investigate for leakage. 4. IF water is suspected 7 THEN blowdown instrument block using S47.8.B accumulator pressure reduction section as guidance.

5. IF HCU indications are normal THEN instruct operator to check spade connectors for looseness in HCU transponder box using S47.8.C Attachment 2 as a guide. NRC JPM A - 2008 Limerick Operating Test 6nfll Appendix C 2 Form ES-C-1 Performance Information 8 Step Element Standard Comment I SatlUnsat (Responds to 1 Acc Alarm Informs CRS of required Note: per ON-I 07) actions for single The ARC for accumulator 2.4 IF one CRD scram inoperable accumulator. trouble does not reference accumulator is inoperable, ON-I 07. However, ON-THEN PERFORM the Cue: 107 provides explicit following within 8 hour9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br />s: CRS acknowledges. guidance for addressing 1. RESTORE the accumulator inoperability.

The applicant is expected to perform ON-107 steps based on training and the fact that the applicant is already implementing the ON procedure for the drive water filter problem. inoperable accumulator to operable OR DECLARE associated control rod inoperable.

completed, THEN TAKE action to be in at least HOT SHUTDOWN within the next 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br />.

2. IF step [I] is not (Responds to 2"d Acc Contacts EO for local Booth operator:

Alarm per ON-107):

If directed to investigate, report back as EO that 2.5 IF more than one cause of accumulator CRD scram accumulator is trouble is low nitrogen inoperable THEN pressure. PERFORM the following: evaluation and refers to ON-I 07. 2.5.1 DECLARE the Informs CRS to declare associated control rods CRD associated with 2nd inoperable. accumulator inoperable.

10 Cue: CRS acknowledges.

NRC JPM A - 2008 Limerick Operating Test 7of11 Appendix C 2 Form ES-C-I Performance Information Step Element Standard Comment I Sat/Unsat

1. 2. 11 -- 2.5.2 IF the control rod Attempts to insert a associated with any inoperable CRD scram notch. accumulator is withdrawn, THEN immediately VERIFY at least one CRD pump is operating:

INSERT a withdrawn withdrawn control rod one control rod one notch. - OR IF loss of RMCS prevents control rod motion, THEN CHECK charging water header pressure 1 1400 psig on "CHARGING WATER PRESSURE" (PX) at *OC603. PSH-46*N600, Note: The selected rod will NOT insert. This action is used per procedure to define whether or not a CRD pump is operating.

If attempt is unsuccessful (and it will be), then applicant will understand NO CRD pumps are operating for the purpose of the subsequent IFlTHEN step in ON-107. Note: Applicant should pJ base hidher determination of CRD pump operating on the second part of this step because there is no loss of the RMCS. However, a check of the charging water header pressure will reveal low pressure.

~ -~ 2.5.3 IF no CRD pump is Not applicable.

Reactor operating AND reactor pressure is greater than or equal to 900 psig, THEN PERFORM the following:

1. START at least one CRD pump within 20 minutes OR manually SCRAM the reactor AND PLACE Reactor Mode Switch in 'ISH U TDO W N , " - OR T-101, as atmlicable.

pressure is < 900 psig.

12 - - AND ENTER T-I 00 NRC JPM A - 2008 Limerick Operating Test 8 of' 1 I Appendix C 2 Form ES-C-I Performance Information Step Element Standard Comment I Sat/Unsat 2.5.4 IF no CRD pump is Depresses scram operating AND reactor pushbuttons.

pressure is less than 900 psig, PERFORM the following:

1. Manually SCRAM the

?3* reactor - AND PLACE Reactor Mode Switch in "SHUT D 0 W N , " - OR T-101, as a mlica ble . - AND ENTER T-100 Cue: JPM is complete.

NRC JPM A - 2008 Limerick Operating Test 9 of11

- Appendix C 3 Form ES-C-1 Verification of Completion Job Performance Measure: NRC JPM A Examinee's Name: - Examiner's Name: Date Performed:

Number of Attempts: Time to Complete: Question Documentation:

Question:

Result: Satisfactory/Unsatisfactory Examiner's signature and date:

NRC JPM A - 2008 Limerick Operating Test 10 of 11

- Applicant JPM Cue Sheet Initial Conditions:

Unit 1 is at 3% power and RPV pressure is 151 psig RPV level is 60 inches, being controlled by LIC-120 in automatic A plant startup is in progress per GP-2, Appendix 1, Reactor Startup and Heatup Control rods are being withdrawn per Control Rod Move Sheet Sequence 1 D LGS Sim U-I .O on Step 17 The next rod move step is to withdraw Control Rod 10-43 There are no channel bow rods Initiating Cue: You are the Reactor Operator. You have been directed to continue with the startup by withdrawing control rods in accordance with the control rod move sheet. NRC JPM A - 2008 Limerick Operating Test NRC JPM 6 2008 Limerick Operating Exam NRC JPM B - 2008 Limerick Operating Test Appendix C Job Performance Measure Form ES-C-1 Worksheet - Facility: Limerick Task Title: Manually Initiate Core Spray Job Performance Measure: NRC JPM B WA

Reference:

295031 EAI.03 (4.4, 4.4) Examinee:

NRC Examiner:

Date: Method of testins:

Simulated Performance:

Classroom Actual Performance:

X Simulator X Plant Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied. Initial Conditions:

0 0 0 0 0 0 0 A seismic event has occurred, resulting in a LOCA with a loss of all offsite power. Reactor has scrammed, all rods inserted, all scram actions have been taken. Reactor vessel water level is minus (-)'l40" on Fuel Zone and lowering. Reactor pressure is 500 psig. Drywell pressure is 17 psig and rising.

D11 and D13 Emergency Diesel Generators have tripped on ground fault. Suppression pool level is 21 feet and slowly lowering. Core spray has failed to automatically initiate. Initiating Cue: Shift Supervision directs you to manually initiate Core Spray System per S52.7.A. An additional RO is available to acknowledge alarms. Another RO has been briefed to perform SE-10 LOCA actions when the LOCA signal has been initiated.

Required Materials: S52.7.A, Manual Initiation After Failure Of Automatic Injection During A LOCA S52.7.8, Core Spray Injection with a Single Operable Pump General

References:

S52.7.A, Manual Initiation After Failure Of Automatic Injection During A LOCA, Rev.

009 332.7.8, Core Spray Injection with a Single Operable Pump, Rev. 9 JPM Origination: Modified Limerick Bank JPM 128, Rev.

000 Task Standard:

NRC JPM B - 2008 Limerick Operating Test 2 ol' 10

-~ Appendix C Job Performance Measure Form ES-C-1 Worksheet Core spray manually initiated and throttled per S52.7.A.

Alternate Path: Yes Time Critical:

No Validation Time: 8 minutes JPM Setup Instructions: Summary Description of JPM: A major seismic event has occurred, where Loop B Core Spray is the only available injection source during a small LOCA.

Loop A LPCl and CS are unavailable due to loss of power to Buses D11 and 013. RHR is unavailable because Loop B RHR Injection Isolatiorl Valves F017B and F017D are jammed closed. A slow suppression pool leak has lowered pool level to less than 22 feet. A large LOCA occurs at the moment the applicant initiates a manual CS initiation signal. Core Spray Pump ID fails to auto start and trips shortly after it is manually started.

RPV pressure is low enough (-200 psig) that Core Spray Pump B will be near runout conditions. Per S52.7.8, the applicant must throttle Loop B Core Spray Inboard Valve F037 to maintain core spray flow as close as possible to the maximum of 31 75 gpm while not exceeding the 3175 gpm limit in order to ensure pump runout (which could lead to pump damage) does not occur. Simulator Setup:

1. Reset to normal at-power IC. 2, Insert the following malfunctions:

a. MHP447B b. MRC466 c. MSL559 d. MFW244A e. MFW245A

f. MFW246A g. MV1237A h. MV1237B i. MV1237C j. MV1237D k. MCS183D I. MCSl82D m. MCS184A n. MRH174B 0. MRH174D p. MDG418A q. MDG418C r. MED261 s. MPC257 t. MRR440A HPCl Aux Oil Pump Trips inadvertent Trip of RClC Overspeed Mechanism SLC Injection Line Rupture Inside the Drywell Reactor Feed Pump A Trip Reactor Feed Pump B Trip Reactor Feed Pump C Trip Reference Leg 1 D004A Level Defect at 60 severity Reference Leg 1D004B Level Defect at 60 severity Reference Leg 1DOO4C Level Defect at 60 severity Reference Leg 1D004D Level Defect at 60 severity Core Spray Pump ID Fails to Auto Start Core Spray Pump 1 D Trips Core Spray Inboard Valve 1 F005 Fails As Is RHR Injection Valve (F017B) Fails As Is RHR Injection Valve (F017D) Fails As Is Diesel Generator D11 Trips Diesel Generator D13 Trips Loss of Offsite Power Supp Pool Leak to Reactor Enclosure at 20,000 gpm severity Recirc Loop A Rupture at 2% severity 3. Override annunciators as needed to provide seismic event alarms.

4. Operate SRVs as needed to reduce and control pressure at approximately 500 psig. 5. When indicated RPV level is approximately minus

(-)I 40, remove Malfunction MRR440A, Recirc Loop A Rupture. NRC JPM B - 2008 Limerick Operating Test 3 Ot'10 Appendix C Job Performance Measure Form ES-C-7 Worksheet

6. Reduce Malfunction MPC257 severity to 2,000 gpm when indicated suppression pool level is approx equal to 21 feet. 7. Set up Trigger 1 to activate on illumination of Core Spray Loop D LOCA Initiation indicating Lamp E21A-Sl7D on 10C601 Panel ( ZLOBl(7540)

). 8. Set up Malfunction MRR440A, Recirc Loop A Rupture at 50% severity on Trigger 1. 9. Set up Override on D124-G-D Supply Breaker Control Switch in CLOSE on Trigger 1 with 5 second delay to simulate operator performing SE-10 actions on LOCA initiation.

10. Set up Override on I OY202 Reset on Trigger 1 with 7 second delay to simulate operator performing SE-10 actions on LOCA initiation.

11. Acknowledge alarms and freeze simulator.

Simulator Tables: 114.?lfirricrrori Eicrrrrrury MallID MULID 1 Description

~ 2 CUneniVdue 1 JavuslVd~~e

] Rmplime I Aclime I Dactime ] Tiig MRC466 MFW244A Reactoi FeedpumpA Tiip Tiue MFW2464 MV1237A MV1237B MV1237C MVI237D MCSl83D MCSlB4A MAH174B MRH174D MDG4184 MDG418C MED261 MPC257 MRR440A MCS lB2D MHP447B HPCl Aux Oil Pump Trips True 000000 000000 000000 0 Inadvertent Trip 01 RClC Dverspeed Mechanism True on0000 000000 000000 0 MSL553 SLC lnleclion Line Ruptrne Inside the DryweU True 000000 000000 000000 0 oooooo oooooo uuueoo n MFW2454 Reactor FadDumD % TIID True 000000 000000 000000 0 WIS Reactor Feedpump C Trip Releience Leg IDOOM Level Delecl Reference Leg lDOO4B Level Delwct Reference Leg lDO04C Level Delect Relererce Leg 1D004D Level Delect Core Spray Pump 1D Fails toAuto Star1 Cote Spray lnlection Valva HV52 1 F005 Fails C RHR Valve HV51 1 F0178 Fails As is RHR Valve HV51 1F017D Fails As is Diesel Generator D11 Trips Diesel Generator 013 Trips Loss of Dflnite Power Leak Fim Suppression Pool (1 100 000 gprnl Recirculation Loop4 Rupture Core Spray Pump 1 D Trips True 60 60 60 60 1 iue True True True True True True 2000 50 1 iue 00 00 00 00 00 00 OD00 00 00 00 00 000000 000000 woo00 0000orJ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 DO 00 00 00 OD 00 00 00 00 00 00 00 00 OD00 00 00 00 00 00 00 00 00 00 00 0000 00 00 00 00 oooooo oomao 00 00 00 00 00 oa 000000 0 DUO000 G 000000 0 000000 0 u00000 0 00000u 0 000000 0 00Do00 0 000000 0 000000 0 00WD0 0 000000 0 OOOUOD 0 000000 1 000000 0 - iictuaiwue 1 OVOI~~~~V~IU~

1 nmptln4c I A~~~v~~ I [Ioctltfis 1 l~~t~ , 52 20224/CS Saieguaid Bus D124 G D Supply Bleakel Control Swltch CLOSE ON 000005 WOO00 52 20224/CS Saleguaid Bus 0124 G D Supply Breaker Control Switch NACLOSi OFF 000005 000000 1 52 202241CS Saleguard Bus D124 G D Supply Breaker Control Switch NATRIP OFF 000005 000000 1 52 20224/CS Safeguard Bus D124 G D SuppC Breaker Contiol Switch TRIP OFF 000005 000000 1 RESET ON 000007 000000 1 43 22422/CS Bieakei Trip RESET IOI 120VAC Panel 1W202 __-__ NRC JPM B - 2008 Limerick Operating Test 4 of 10 Form ES-C-I Appendix C 2 Performance I n f or ma t io n Critical steps denoted with an asterisk t Step Element Standard Comment I Sat/Unsat Not applicable TURN collar of the following MANUAL INITIATION pushbuttons to "ARM ED": a. (INITIATION l) E21- Rotates core spray manual S22A clockwise to the ARMED Dosition. Not critical since D11 de- S22A initiation pushbutton collar energized.

2 b. (INITIATION

2) E21- Rotates core spray manual S22B initiation pushbutton collar S22B clockwise to the ARMED Dosition.

3" C. (INITIATION

3) E21- Rotates core spray manual S22C clockwise to the ARMED position. Rotates core spray manual S22D initiation pushbutton collar Pump D will not auto start Not critical since D13 de- s22c initiation pushbutton collar energized.

4 d. (INITIATION

4) E21- Not critical since CS 5 S22D clockwise to the on init signal. Must be ARMED position. manually started. VERIFY the following Not applicable annunciator alarms:

DIV 1 CORE SPRAY MANUAL INITIATION Spray manual initiation SWITCH ARMED switch armed annunciators AND MANUAL INITIATION SWITCH ARMED, annunciator alarms on *I 3 COOL A DIV 2 CORE SPRAY MANUAL INITIATION Spray manual initiation SWITCH ARMED switch armed annunciators AND MANUAL INITIATION SWITCH ARMED, annunciator alarms on

• I 5 DIV 1 and DIV 3 Core are verified lit on 113 7 DIV 3 CORE SPRAY COOL A.

DIV 2 and DIV 4 Core are verified lit on 11 5 8 DIV 4 CORE SPRAY COOL B. NRC JPM B - 2008 Limerick Operating Test 5 of 10 Appendix C 2 Form ES-C-1 Performance Information Step Element Standard Comment

/ SatlUnsat

~ DEPRESS AND RELEASE NIA all four of the following 9 MANUAL INITIATION pushbuttons to initiate a. (INITIATION

1) E21- Momentarilly depresses Not critical since D11 de- Core Spray System:

_- S22A and then releases energized.

MANUAL INITIATION 10 pushbutton S22A. - b. (INITIATION

1) E21- Momentarilly depresses S22B and then releases MANUAL INITIATION pushbutton S22B.

1 I* C. (INITIATION

1) E21- Momentarilly depresses Not critical since D13 de- s22c and then releases energized.

MANUAL INITIATION nushbutton S22C.

12 13 d. (INITIATION 1) E21- Momentarilly depresses Not critical since CS S22D and then releases Pump D will not auto start MANUAL INITIATION on init signal.

Must be pushbutton S22D. manually started.

Cue: If necessary, inform applicant that another RO has been directed to perform SE-10 actions upon LOCA signal initiation. Start the "1 D" Core Spray Recognizes only 1 B Core Pump. Spray started. Informs However, step is critical supervisor and manually starts ID Core Spray Pump. established without Pump trips on start. since required two-pump operation could not be attempting a start. 14* ENSURE the following Core Spray Pump power. minimum flow bypass valves are open: -HV-52-*FU31A, MIN valve HV-52-1 F031 B is FLOW closed as expected with -HV-52-*FU31 B, MIN flow greater than 775 gpm FLOW after 3 second delay. Determines F031A has no Verifies minimum flow 15 NRC JPM B - 2008 Limerick Operating Test 6 of' 10 Appendix C 2 Form ES-C-1 Performance I nformat ion Step Element Standard Comment I SaWnsat ~~ ~ WHEN Reactor Pressure is Determines following between 435 to 475 psig, actions are required l6 THEN VERIFY the because pressure is following: already less than 435 psig.

HV 52 *F005, Verifies HV-52-1 F005 is OUTBOARD, open. open 17 Note: L.oop A pumps are not running so F005 position verification not imDortant.

HV 52 *F037, INBOARD Verifies HV-52-1 F037 is l8 DISCHARGE.

oDen. 013817. NOTE: Recognizes only 1B CS Begins Alternate Path Two pump operation is required to prevent pump S52.7.B. damage due to run out. IF only one Core Spray Pump in a loop is running, THEN GO TO S52.7.8, Core Spray Injection with a Single Operable Pump. IF single operable Core Not applicable.

CS Pump Spray Pump in loop is not essential to maintain reactor level, 2o THEN PERFORM the following: 1. TRIP pump 2. EXIT procedure IF single operable Core Verifies pump has not run Note: SP level indicated Spray Pump in loop is >I hr. Verifies SP temp on L152-140A at 1OC626 essential to maintain ~198°F. Determines SP will continue to indicate reactor level, level is NOT > 22 feet. 23.6' due to the power THEN VERIFY all three of failures. Applicant will the following conditions for Informs supervisor that all need to realize this is not operation are satisfied: three conditions are NOT a valid indication based 21 1. Pump is run no longer met.

Pool level is c22 feet. on LR55-115 at 10C648 than one hour. (20.8') and also plant temperature less than 198°F. 3. Suppression pool level greater than 22 feet. Pump running. Refers to operation is essential.

2. Suppression pool computer (21')

NRC JPM B - 2008 Limerick Operating Test 7 of 10 Appendix C 2 Form ES-C-? - Performance Information Step Element Standard Comment I Sat/Unsat IF all three conditions are not met, THEN OBTAIN SSV approval AND THROTTLE HV 52 Requests approval to throttle HV-52-1 F037 to 3175 gpm on FI 1 R6016, FL, at panel 1 OC601. AND DISCHARGE to less than gpm.

3,775 gpm on FI 52 *RGOIA(B), FL, at panel *OC601. gpm to 3175 gpm] *F005(A Loop)/HV - '** *F037(0 Loop), Throttles flow to ~3175 [Acceptable range is 2900 Cue: JPM is comdete. NRC JPM B - 2008 Limerick Operating Test 8 oil0 3 Form ES-C-? Appendix C Verification of Completion Job Performance Measure:

NRC JPM B Examinee's Name: Exam ine r's Name: -- Date Performed:

Number of Attempts:

Time to Complete: Question Documentation:

Question:

Response:

Result: SatisfactorylUnsatisfactory Examiner's signature and date:

NRC JPM B - 2008 Limerick Operating Test 9 Of'lO

- Applicant JPM Cue Sheet Initial Conditions:

A seismic event has occurred, resulting in a LOCA with a loss of all offsite power Reactor has scrammed, all rods inserted, all scram actions have been taken. Reactor vessel water level is minus (-)140" on Fuel Zone and lowering.

Reactor pressure is 500 psig. Drywell pressure is 17 psig and rising. D11 and DI 3 Emergency Diesel Generators have tripped on ground fault. Suppression pool level is 21 feet and slowly lowering.

Core spray has failed to automatically initiate.

Initiating Cue: Shift Supervision directs you to manually initiate Core Spray System per S52.7.A. An additional RO is available to acknowledge alarms. Another RO has been briefed to perform SE-10 LOCA actions when the LOCA signal has been initiated.

NRC JPM B - 2008 Limerick Operating Test NRC JPM C 2008 Limerick Operating Exam NRC JPM C - 2008 Limerick Operating Test Appendix C Job Performance Measure Form ES-C-1 Worksheet Facility: Limerick Task Title: Open An MSlV WA

Reference:

239001 A2.03 (4.0, 4.2) Examinee: Job Performance Measure:

NRC JPM C NRC Examiner:

Date: Method of testing:

S i m u la t ed Perform a nce : Actual Performance:

X Classroom Simulator X Plant Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied. Initial Conditions:

0 Unit 1 is at 35% power. Outboard MSlV HV-41-1 F028B closed due to a rupture of the air exhaust line from the MSIV. The MSlV air exhaust line has been repaired.

A second RO is available to monitor reactor power. Initiating Cue: You have been directed to open the MSlV per 541.3.8. Required Materials:

None General

References:

S41.3.B, Reopening A Single Isolated MSIV, Revision 11 JPM Origination: New Task Standard: Reopen a spuriously closed MSlV at power Alternate Path: No Time Critical:

No Validation Time:

8 minutes JPM Setup Instructions:

NRC JPM C - 2008 Limerick Operating Test 2 of10

__~ Appendix C Job Performance Measure Form ES-C-1 Worksheet Summary Description of JPM: The applicant will open the MSIV in accordance with 541.3.8. Simulator Setup:

1. 2. 3. 4. 5. 6. Reset to approximately 35%

power. Insert Malfunction MMS064B to fail closed Inboard MSIV HV-41-1 F022B Place HV-41-1 F028B in TEST on 1 OC601. Remove Malfunction MMS064B. Allow plant to stabilize. Place simulator in Freeze. NRC JPM C - 2008 Limerick Operating Test 3 of. 10 Appendix C 2 Form ES-C Performance Information Critical steps denoted with an asterisk Step Element Standard Comment I SatlUnsat CAUTION Informs HP.

Steps 4.3.2 through 4.3.9 removes condensate from Cue: Main Steam lines prior to opening MSlV @JlJ placing Main Steam line inservice, - AND may change dose rates in the vicinity.

HP has been notified.

1 (Step 4.3.1) INFORM HP that the valves listed in step 4.3.2 will be operated AND another steam flow path is being established. (Step 4.3.2) ENSURE alignment of the System valves at panel "OC601: 0 HV-C-41-*F020, Main Ensure HV-C-41-1 F020 is 2 following Main Steam Steam Line Pressure open.

Equalizing Valve - OPEN 3* 0 HV-41-*42 Bypass Ensure HV-41 -1 42 is 4* Leakage Barrier Block open.

OPEN HV-41-*43 Bypass Ensure HV-41-143 is 5* Leakage Barrier Block open. OPEN NRC JPM C - 2008 Limerick Operating Test 4 01'10 Appendix C 2 Form ES-C-I - Performance Information Step Element Standard Comment I SatlUnsat CAUTION Reactor power must be closely monitored while performing steps 4.3.3 through 4.3.12. (Step 4.3.3) ALIGN the following Main Steam System valves to drain condensate from upstream AND downstream piping around outboard MSlV at panel *OC601: HV-41-*F016, Main Opens HV-41-1F016. Steam Drain -OPEN 7" 0 HV-41 -*FO19, Main Opens HV-41-1 FO19. 0 HV-41-*F021, Main Opens HV-41-1 F021. Steam Drain - OPEN Steam Drain To Cond - OPEN 8* 9 (Step 4.3.4) OPEN HV-01-*04, Main 1 OC653. (STARTUP DRAIN), at Dane1 *OC653. Opens HV-01-104 at Panel IO* Steam Line Startup Drain NRC JPM C - 2008 Limerick Operating Test 5of 10 Form ES-C-'1 Appendix C 2 Performance Information Step Element Standard Comment I SatlUnsat NOTE Cue: S06.1 .I U/*, Accessing If asked, inform applicant Information At The Feedwater Level Control

' System Operator Station, provides directions on how to access screens at FWLCS Operator Station.

that MSlV was NOT isolated IAW S41.3.C. 11 CAUTION 1. Only equipment associated with the main steam line with the MSlV being reopened is to be operated.

2. MSIV's are designed to open with no more than 200 psid. (Step 4.3.5) IF MSlV was not isolated in accordance with S41.3.C, Isolation of One Main Steam Line at Power (i.e. unplanned MSlV closure), THEN PERFORM the following:

1. DEPRESS white Depresses SINGLE SINGLE pushbutton on LIC-MI -*R600, Reactor Level Controller (MASTER, LV), at panel *OC603. 2. VERIFY white SINGLE pushbutton is lit on LIC- MI -*R600, Reactor Level Controller (MASTER, LV), at panel

• OC603. pushbutton on LIC-MI- 1 R600 on 1 OC603 12* Verifies SINGLE pushbutton is lit. 13 3. MARK steps 4.3.6.1, Marks steps as NIA. 14 4.3.6.2 and 4.3.6.3 as N/A AND CONTINUE.

NRC JPM C - 2008 Limerick Operating Test 6 oS10 Appendix C 2 Form ES-C-1 Performance Information SteD Element Standard Comment I SatIUnsat (Step 4.3.6) Not applicable.

VERIFY MSlV Test Mode Operator Station as follows.. . 15 is activated at FWLCS NOTE Closes HV-41-1 F022B The outboard MSlV should be opened soon after inboard MSlV is fully closed. (Step 4.3.7)

C, D), Inboard MSIV, at panel *OC601. (INBOARD) at Panel 1 OC601. 16* CLOSE HV-41-*F022A(B, (Step 4.3.8) Places handswitch in OPEN HV-41 -*F028A( B, C, AUTO for HV-41-1 F028B panel *OC601. 1 OC601 Observes valve 17* D), Outboard MSIV, at (OUTBOARD) at Panel open. (Step 4.3.9) Cue: WAIT 5 to 10 minutes 18 before proceeding to the next step to allow condensate to drain. 10 minutes have elapsed. (Step 4.3.10) Places handswitch in OPEN HV-41-*F022A(B, C, AUTO for HV-41-1 F022B 19* D), Inboard MSIV, at panel (INBOARD) at Panel *OC601. 1 OC601. Observes valve oDen. (Step 4.3.1 1) ALIGN the following Main Steam System drain directed by GP-2, Normal Plant Startup, at panel

• OC601: 20 valves, unless otherwise 0 HV-41-*F016, Main Closes HV-41-1F016.

HV-41 -*F019, Main Closes HV-41-1 FO19. Steam Drain- CLOSED Steam Drain - CLOSED 21

• 22* ~ -~ ~ 0 HV-41-*F021, Main Closes HV-41-1 F021 23* Steam Drain To Cond - CLOSED ~ NRC JPM C - 2008 Limerick Operating Test Appendix C 2 Form ES-C-1 Performance information Step Element Standard Comment I SatlUnsat (Step 4.3.12)

CLOSE HV-01-*04, Main 1 OC653. (STARTUP DRAIN), at panel *OC653. S06.1 .I U/*, Accessing Information At The Feedwater Level Control System Operator Station, provides directions on how to access screens at FWLCS Operator Station. Closes HV-01-104 at Panel 24* Steam Line Startup Drain NOTE CAUTION IF MSlV Test Mode is deactivated with an inboard 25 MSIVOR outboard MSlV closed, THEN an RPV level transient will occur. (Step 4.3.13) IF MSlV was not isolated in accordance with S41.3.C, Isolation of One Main Steam Line at Power (i.e. unplanned MSlV closure), THEN PERFORM the following: 1. DEPRESS white THREE pushbutton on LIC-MI- Controller (MASTER, LV), at panel *OC603. 2. VERIFY white THREE pushbutton is lit on LIC- Ml-*R600, Reactor Level Controller (MASTER, LV), at panel *OC603. Depresses THREE pushbutton on LIC-MI- 26* *R600, Reactor Level 1 R600 on Panel 1 OC603. Verifies THREE pushbutton is lit. 27 3. MARK step 4.3.14 as N/A AND CONTINUE Marks the step N/A.

28 ~~ ~ Cue: JPM is complete. - NRC JPM C - 2008 Limerick Operating Test 8 oflo

- Form ES-C-1 Appendix C 3 Verification of Corn p le t i o n Job Performance Measure:

NRC JPM C Examinee's Name: Examiner's Name: Date Performed:

Number of Attempts:

Time to Complete:

Question Documentation:

Question:

Response:

Result: Satisfactory/Unsatisfactory Examiner's signature and date:

NRC JPM C - 2008 Limerick Operating Test 9 of10 Applicant JPM Cue Sheet - Initial Conditions:

0 0 0 0 Unit 1 is at 35% power. Outboard MSlV HV-41-1 F028B closed due to a rupture of the air exhaust line from the MSIV. The MSlV air exhaust line has been repaired.

A second RO is available to monitor reactor power. Initiating Cue:

You have been directed to open the MSlV per S41.3.B. NRC JPM C - 2008 Limerick Operating Test NRC JPM D 2008 Limerick Operating Exam NRC JPM D - 2008 Limerick Operating Test Appendix C 2 Form ES-C-1 Performance Information Facility: Limerick Task Title: Manually Start HPCl Job Performance Measure: NRC JPM D WA

Reference:

206000 A2.06 (3.3, 3.5) Examinee: NRC Examiner:

Date: Method of testing: Si m u I a t ed Perform an ce : Classroom Actual Performance:

X Simulator X Plant Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied.

Initial e e 0 e e e e e e e e Cond it ions:

Unit 1 is at 100% power No equipment is out of service Steam Leak Detection System is available Suppression Pool Cooling is in service HPCl Oil Reservoir is filled to high in the normal operating range on sightglass HPCI is lined-up for automatic operation per S55.1 .A Reactor Enclosure Equipment Compartment Exhaust is in service ST-6-060-390-1 is currently being performed by the Reactor Operator No maintenance has been performed on the Turbine oil system or governor control system No water was drained from any part of the system The Vibration Monitoring System is in service Initiating Cue: You are directed by Shift Supervision to place Unit 1 HPCl in full flow test, CST to CST, with pump discharge pressure at least 120 psig greater than reactor pressure, using the manuai quick start method for a 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> PMT per S55.1 .D. Required Materials:

S55.1 .D, HPCl System Full Flow Functional Test, Rev. 34, with prerequisites signed off. Genera I Ref e re n ces : S55.1.D, HPCI System Full Flow Functional Test, Rev.

34 HU-AA-104-101, Procedure Use and Adherence, Rev 03 NRC JPM D - 2008 Limerick Operating Test Page 2 of' 9 Appendix C 2 Form ES-C-1 Perform a nce I n fo r mat io n JPM Origination: Modified Limerick Bank JPM 19 Revision 008 Task Standard:

Starts HPCl in full flow test (CST to CST) lineup, with pump discharge pressure at least 120 psig greater than reactor pressure, using manual quick start method. Trips turbine within 3 minutes after start due to lack of min flow protection.

Alternate Path: Yes Time Critical: No Validation Time:

7 minutes JPM Setup Instructions: Summary Description of JPM: The applicant is directed to perform full flow HPCl test from CST back to CST. Helshe will partially align HPCl full flow path back to CST by opening Condensate Return Valve HV 1 FOI 1. Min Flow Valve HV-55-1 F012 is in normal pre-start closed position, but is failed as- is, such that it will not open when demanded by pump discharge pressure

>I25 psig and pump flow 650 gpm. The applicant will start the HPCl turbine and, per procedure, will attempt to open HPCl Test Loop Shutoff HV-55-1 F008 to establish full flow conditions. However, the valve is thermally bound and will not open. The applicant will announce unexpected indications and will attempt to open Min Flow Valve HV-55-1 F012. Per precautions, HPCl is not allowed to run without min flow protection for greater than 60 seconds. The applicant will recognize the challenge to this limitation and trip the HPCl turbine within 3 minutes from the time pump discharge pressure exceeds 125 psig.

The 3 minute time limit was established based on a response time of no more than 3 times the value stated in the precaution.

A 3 minute response is reasonable as a maximum acceptable time, given the procedural emphasis on actions to attempt to open the F008 full flow line isolation valve.

As soon as the applicant realizes F008 is not going to open, it is expected they will assess the pump alignment, determine the min flow valve is closed and trip the HPCl pump. Simulator Setup:

1. 2. 3. 4. 5. 6. 7. 8. Reset to a full power IC Place Suppression Pool Cooling in service Place B Loop ESW in service Override HPCl Min Flow Valve HV55-1 FO12 indicating lights (green-ON, red-OFF) to indicate valve closed.

Override HPCl Test Bypass to CST, HV55-1 F008 handswitch to PTS. Override HPCl Pump Disch Pressure Indication (P155-1R601) to 1500 on trigger

1. Activate trigger I on HPCl speed 2 4500 (HPNT >= 4500). Acknowledge alarms and freeze simulator.

NRC JPM D - 2008 Limerick Operating Test Page 3 of9

~ Appendix C 2 Form ES-C-1 Performance Information Critical steps denoted with an asterisk Step Element Standard Comment I SatlUnsat Not applicable IF required to limit Suppression Pool temperature anytime during this procedure, then refer to S51.8.A Suppression Pool Cooling Operation (Startup and Shutdown) and Level Control, and PLACE Suppression Pool Cooling Mode of RHR System in Service If Vibration Monitoring Not applicable System is available, then verify in service Cue: Vibration Monitoring system is in service. Ensure the following valves Verifies valves closed by are CLOSED: position indication:

HV-55-1 F071, "HPCIIRCIC Green lights ON 2 Flush Line to Suppression Pool" (TEST OUTBOARD)

HV-55-1 F008, "Test Loop Red lights OFF 3 Shutoff" (TEST ISOL) HV-55-1 FOI 1, "HPCVRCIC Test Return to CST" (CONDENSATE RETURN)

Loop Isolation"(TEST 0 HV-49-1 F022, "RCIC Test ISOL) Open HV-55-*F011, Places handswitch in 4* Condensate Return. OPEN. Observes valve indicates full open. Takes handswitch to start. 10P216 indicates running. START 1 OP0216, " Ba ro m e t r ic Con denser Vacuum Pump" (VACUUM PUMP). NRC JPM D - 2008 Limerick Operating Test Page 4 of9 Appendix C 2 Form ES-C-1 Performance Information Step Element Standard Comment

/ SatlUnsat Monitor Suppression Pool Not applicable. temperature per ST-6-060- 390-1, Suppression Pool Temperature Check.

Cue: ST-6-060-390-1 is being performed by an additional operator.

INFORM HP of changing to HPCl System start. ENSURE FIC-55-*R600, FIC-55-1 R600 MIA selector "HPCI Pump Discharge switch in the "A" position.

to 5600 gpm in "AUTO" 1 R600 set between 5,500 and 5,700 GPM. Make Plant Announcement Plant Announcement for for HPCI startup. HPCl startup performed. Simultaneously open HV- Simultaneously positions Examiner Note:

55-1 FOOI, "HPCI Steam handswitches. HV Begin timer when FOO1 Supply" (INLET) AND Start handswitch is placed in Pump" (AUX OIL PUMP). When Sl-56-161, "Turbine Speed" (S), starts to go up, then immediately throttle open HV-55-1 F008, "HPCI Test Loop Shutoff" (TEST ISOL), until desired flow is obtained, while maintaining

turbine speed greater than 6 HP notified HPCI start is 7 radiological conditions due imminent.

8 Flow Controller" (FL), set Flow controller FlC IF001 is open and 10P213 lo* 1 OP213, "Auxiliary Oil is running. OPEN. Start time: Observes speed increase. Immediately opens F008 Valve. Maintains speed

> 2200 rpm.

1 I* 2,200 rpm. - NRC JPM D - 2008 Limerick Operating Test Page 5 01'9 Appendix C 2 Form ES-C-1 Performance Information Step Element Standard Comment I SatlUnsat Recognizes pump flow is Observes pump flow is not Note: not increasing. increasing. Informs Will not be able to supervisor. establish flow because Cue: Acknowledge report.

1 F008 is thermally bound and will not move. 12 13* Note: (Procedure Use and Adherence)

Step 3.1.7 requires test procedure stopped at current step because procedure cannot be performed as written (cannot get flow to increase) and because continuation would result in an unsafe condition (running pump without min flow). H U-AA- 1 04- 1 0 1 Attempts to open Min Flow Observes min flow valve Note: Valve HV-55-1 F012. F012 is not open. Informs F012 is failed closed, supervisor.

Attempts to however by design it open HV-55-1 F012. should automatically open at e550 gpm with disch Cue: Acknowledge report. pressure

> 125 psig.

S55.1 .D, Precaution 3.7 states in part, "Operator action may be required to open HV-55-1 F012, MIN FLOW valve". NRC JPM D - 2008 Limerick Operating Test Page 6 01'9

-~ Appendix C 2 Form ES-C-1 Performance Information Step Element Standard Comment I Sat/Unsat within 3 minutes and 10 "Do not allow HPCl to seconds after opening operate without min flow 1 Fool Steam Supply protection for greater than Valve. 60 seconds." (S55.1 .D, Step 3.7). Takes Cue: applicant approximately 10 seconds recommends tripping HPCl for HPCl discharge turbine, then acknowledge pressure to increase to > report and direct the 125 psig following the applicant to trip the HPCl positioning of 1 FOOI turbine. handswitch to open. Trips the HPCl turbine. Trips the HPCl turbine Note: 14* Examiner Note:

Stop time: Elapsed time from 1 Fool handswitch operation must be approximately 5 I90 seconds (1 0 seconds for pump discharge pressure to increase 1 125psigand 180seconds to respond to the abnormal flow indications by tripping the HPCl pump). NRC JPM D - 2008 Limerick Operating Test Page 7 o 9 Appendix C 3 Form ES-C-I Verification of Completion Job Performance Measure:

NRC JPM D Examinee's Name: - Examiner's Name: - Date Performed:

Number of Attempts:

Time to Complete: Question Documentation:

Question:

Response:

Result: Satisfactory/Unsatisfactory Examiner's signature and date:

NRC JPM D - 2008 Limerick Operating Test Page 8 of'9 Applicant JPM Cue Sheet Initial Conditions:

Unit 1 is at 100% power No equipment is out of service Steam Leak Detection System is available Suppression Pool Cooling is in service HPCl Oil Reservoir is filled to high in the normal operating range on sightglass HPCl is lined-up for automatic operation per S55.1 .A Reactor Enclosure Equipment Compartment Exhaust is in service ST-6-060-390-1 is currently being performed by the Reactor Operator No maintenance has been performed on the Turbine oil system or governor control system No water was drained from any part of the system The Vibration Monitoring System is in service Initiating Cue: You are directed by Shift Supervision to place Unit 1 HPCl in full flow test, CST to CST, with pump discharge pressure at least 120 psig greater than reactor pressure, using the manual quick start method for a 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> PMT per S55.1 .D. NRC JPM D - 2008 Limerick Operating Test NRC JPM E 2008 Limerick Operating Exam NRC JPM E - 2008 Limerick Operating Test Appendix C Job Performance Measure Form ES-C-1 Worksheet Facility: Limerick Task Title: Initiate Containment Spray Job Performance Measure: NRC JPM E WA

Reference:

226001 A4.03 (3.5, 3.4) Examinee: NRC Examiner:

Date: Method of testing:

Si m u la ted Performance

Actual Performance:

X Classroom Simulator X Plant Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied. Initial Conditions:

e e The reactor is shutdown due to a large steam leak inside primary containment. Reactor water level is being maintained by the RO using S/U level control. Cooling water is not required to the Post LOCA Recombiners and the HV57-168A valve has been verified closed. 1A and 1B RHR Pumps have both tripped. Initiating Cue:

You are directed by Shift Supervision to establish to initiate drywell spray using the fire protection system cross-tie per T-225. Required Materials: Copy of T-225, Startup And Shutdown Of Suppression Pool And Drywell Spray Operation General

References:

T-225, Startup And Shutdown Of Suppression Pool And Drywell Spray Operation, Rev. 20 JPM Origination: Modified Limerick Bank JPM 32, Rev. 005 Task Standard: Establish Drywell Spray with Fire Water Alternate Path: No Time Critical: No Validation Time: 10 min JPM Setup Instructions:

NRC JPM E - 2008 Limerick Operating Test 2 of l?

Appendix C Job Performance Measure Form ES-C-1 Worksheet Summary Description of JPM:

The applicant is directed to spray the drywell using fire water.

The applicant will perform Section 4.7 to align fire water for drywell spray. This JPM has applicant perform different actions than those performed during Part C scenarios.

Use of fire water requires operation of the F0486, F003B and F004B valves and also includes fire protection system verifications. Simulator Setup:

1. Reset the simulator to IC 17. 2. Insert Steam Leak in Drywell - Malfunction MMS067 at 2000 gprn. 3. The following actions should be taken: a. Mode switch to SHUTDOWN b. Insert SRM's

& IRM's c. Line up Condensate System to STARTUP level control with 138A in AUTO d. Bypass and restore D/W Cooling 4. Reduce the steam leak to 300 gpm when drywell pressure reaches 25 psig. NOTE: This will keep reactor pressure high enough to prevent the LOCA signal from coming in while the JPM is being performed.

5. Set up Malfunction MRHl71 B to trip 1 B RHR Pump on Manual Trigger

1. 6. Set up Remote RTR267 for YES to open FW cross-tie on Manual Trigger

2. 7. Acknowledge and reset Alarms and FREEZE the simulator. Simulator Tables

Maffrrrrcrtorr Strrrirrwry k4alf ID Mull ID Descfiplim

~~?.i&t\l&r:

--] T.ipetValue

-[Rmdime ] 4ctime- ] Dactime 1 Trig MMS067 Steam Leak m Diywell(0 5000 gpm) 300 00oow 000000 000000 0 MRH1718 RHR Pump IS Trips True 0000Do 000000 000000 1 ,~-~ I --,- -I^__- ~ --__I- I im&e- I Acme ] Tiic iayat v,, YES 000000 000000 2 -~ RTR267 T 225 Fue Wale, Ciorslie to RHR NRC JPM E - 2008 Limerick Operating Test 3 of0

~ Appendix C 2 Form ES-C-1 Performance Information Critical steps denoted with an asterisk Ster, Element Standard Comment I SatlUnsat ENSURE the following Refers to Section 4.7 of T-1 valves closed: 225, Fire Water Crosstie. HV-51-1 F004B, 1 B RHR 2* Pump Suction PClV (SUCTION B) Closes valve.

e e 3 e HV-51-1 F0068, 1 B RHR Pp S/D Clg Suct Intertie Vlv (SUCTION B) Shutdown Clg Injection PClV (OUTBOARD)

Cntmt Spray Line Outboard PClV (OUTBOARD) LPCl lnj PClV (OUTBOARD) Verifies valves closed.

HV-51-1F015B, 1B HV-51-1F016B, 1B RHR HV-51-1 F017B, 1 B RHR HV-51-1 F024B, 1 B RHR Pp Full Flow Test 4* Return Vlv (SUPP POOL CLG B) Closes valve. HV-51-1 F027B, 1 B RHR Supp Pool Spray Line PClV (SUPP POOL SPRAY) Verifies valve is closed HV-51-1 F0476, I B RHR 6* Htx Shell Side Inlet Vlv (INLET) Closes valve. HV-51-1 F048B, 1 B RHR Htx Shell Side 7* Bypass Vlv (HEAT EXCH BYPASS) Closes valve. 051-1 F098, Cond Trans Fill lsol Vlv to closed. R11-253) Cue: (ATTACHMENT 6)

Valve is closed. Directs EO to verify valve 8 1A & 1B RHR LOOPS (402-NRC JPM E - 2008 Limerick Operating Test 4of9 Appendix C 2 Form ES-C-1 Perfor ma nce I n fo r mat ion Step Element Standard Comment I SatlUnsat PERFORM the following in Directs EO to perform Booth operator:

402-R16-253 local fire water alignment. Activate Manual Trigger #2 (ATTACHMENT 5): 1. CONNECT hose at 51-1 179, 1 B RHR Fire Protection Crosstie Connection Drain directed.

Valve AND Route to drain THEN CYCLE 51 -1 179 open AND closed to ensure piping vented. 2. CONNECT hose at 22-1 430, Fire Protection/RHR Interconnect ion Drain Valve AND Route to drain THEN CYCLE 22-1430 open AND closed to ensure piping vented. 3. CONNECT hose to fitting downstream of 22-1 429, Fire Protection/RHR Interconnect ion Isolation Valve. of hose to 51 -1 178, 1 B RHR Fire Protection Crosstie Connection Isolation Valve. to locally align fire water. Report back as EO that fire water aligned as 9* 4. CONNECT other end

5. OPEN 22-1429. 6. OPEN 51 -1 178. NRC JPM E - 2008 Limerick Operating Test 5 of9 Appendix C 2 Form ES-C-I - Perfor ma nce I nfo r mat ion Step Element Standard Comment I SatlUnsat Step is critical for SRO applicants only. REQUEST SSV verify D/W pressure and Note: drywell temperature AND drywell pressure are on SAFE side of Drywell Spray Initiation Limit curve per T-I 02, Primary Containment Control OR drywell. SAMP-1, RPV and Primary Containment Flooding Control. You are directed to temperature readings are given to the CRS prior to Spraying and confirmation is received from the CRS that it is Safe to spray the Cue for SRO Applicant: determine if on safe side of Drywell Spray Initiation Curve. 1 o* Cue for RO Applicant: Request drywell temperature and pressure. After being given D/W temperature and pressure readings, state that it is safe to spray the drywell. Verifies pumps tripped. Turns fans OFF. Trip Reactor Recirc Pumps. REMOVE Drywell Cooling Fans from service by placing all 16 Drywell Cooler Fan switches to OFF. MONITOR Drywell Drywell pressure is PERFORM the following to initiate LOCA signal for B Loop: Place El 1A-S61 B, INITIATION, switch for B 15* Loop operation at panel 1 O?C601 (Main Control Room) to "ARM". 12* l3 pressure.

observed.

14 Places switch in ARM. ~~ ~ DEPRESS AND RELEASE Depresses and releases 16* El 1A-S61B. switch. ~~~~~ ~ VERIFY LOOP B 17 INJECTION white indicating light Lit. Verifies white light lit.

NRC JPM E - 2008 Limerick Operating Test 6 of 0 Appendix C 2 Form ES-C-1 Performance Information Step Element Standard Comment I SatlUnsat OPEN HV-51-1F021B, IB RHR Cntmt Spray Line Inboard PCIV, (INBOARD) RHR Cntmt Spray Line Outboard PCIV, (OUTBOARD), at 10C601. ENSURE OOP512, Motor Driven Fire Pump, OR

' OOP511, Diesel Driven Fire Pump, running. Cue: JPM is complete.

Per Step 4.7.10, opens va I ves . 18* AND HV-51-1FO16B, 16 Verifies Motor OR Diesel Driven Fire Pump running.

NRC JPM E - 2008 Limerick Operating Test Appendix C 3 Form ES-C-1 Verification of Completion Job Performance Measure:

NRC JPM E Examinee's Name:

Examiner's Name: - Date Performed:

Number of Attempts:

Time to Complete:

Question Documentation:

Question:

Response: Res u I t : Sat i sf a c t o r y! U n s a t i sf a c t o r y Examiner's signature and date:

NRC JPM E - 2008 Limerick Operating Test 8 :Jf 9 Applicant JPM Cue Sheet Initial Conditions:

0 The reactor is shutdown due to a large steam leak inside primary containment. Reactor water level is being maintained by the RO using S/U level control. Cooling water is not required to the Post LOCA Recombiners and the HV57- 168A valve has been verified closed. 1A and 1B RHR Pumps have both tripped Initiating Cue: You are directed by Shift Supervision to establish to initiate drywell spray using the fire protection system cross-tie per T-225.

NRC JPM E - 2008 Limerick Operating Test NRC JPM F 2008 Limerick Operating Exam NRC JPM F - 2008 Limerick Operating Test Appendix C Job Performance Measure Form ES-C Worksheet Facility:

Limerick Task Title: Transfer Loads to Unit Aux Trans Job Performance Measure:

NRC JPM F K/A

Reference:

262001 A4.04 (3.6, 3.7)

Examinee:

NRC Examiner:

Date: Method of testing: Simulated Performance:

Classroom Actual Performance:

X Simulator X Plant Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied.

Initial Conditions:

0 GP-2 is being performed on Unit 1. 1 I and 12 Unit Auxiliary Busses are being powered from offsite sources. Initiating Cue:

You are directed by Shift Supervision to transfer house loads for Unit 1 to the Unit Aux. Transformer per S91.6.A.

Required Materials:

None General

References:

S91.6.A, Transferring House Loads To Unit Auxiliary Transformer, Rev. 15 JPM Origination: Limerick Bank JPM 25, Rev. 004 Task Standard:

11 and 12 Unit Auxiliary Busses being supplied by the Main Generator Alternate Path: No Time Critical:

No Validation Time: 10 minutes JPM Setup Instructions:

Simulator Setup: 1. Reset simulator to any power IC. 2. Transfer 11 and 12 busses to offsite.

NRC JPM F - 2008 Limerick Operating Test 2 of 8

- Appendix C Job Performance Measure Form ES-C-1 Worksheet - 3. Ensure that only one 13.2 kV aux bus is selected for fast transfer to a given offsite source. NRC JPM F - 2008 Limerick Operating Test 3 ot 8 Appendix C 2 Form ES-C-? .- Perform an ce I n f o rm a t i o n Critical steps denoted with an asterisk SteD Element Standard Comment / Sat/Unsat Obtain current revision of S91.6.A. obtained.

Current revision of S91.6.A Cue: Provide copy of S91.6.A to applicant after applicant demonstrates the ability to locate the current revision of the Procedure. Determining section to perform. Refers to Section 4.2. Perform the appropriate section as follows: 1. Perform Section 4.2 to 2 transfer 11 Aux Bus 2. Perform Section 4.3 to transfer 12 Aux Bus. 3. Perform Section 4.4 to transfer 21 Aux. Bus. 4. Perform Section 4.5 to transfer 22 Aux Bus. Place 225-1 01 13/SS 3" synchronization switch to ON. Verify incoming voltmeter read approximately 1 1 OV. IF incoming / running voltages differ by greater than 8 volts, THEN adjust startup bus voltage to obtain less than 8 volts difference. Places Sync Switch to ON. Observes that V/I-UAS and approximately 1 1 OV. Observes that V/I-UAS and V/R-UAS voltages are within 8 volts of each other. 4 AND running voltmeter VIR-UAS are both CLOSE and HOLD 252- 101 13/CS, Aux Feed. Holds 252-1 01 13/CS in CLOSE when incoming and running voltages are both approximately 1 10 and within 8 volts of each other. 6* NRC JPM F - 2008 Limerick Operating Test 4of8 Atmendix C 2 Form ES-C-1 Performance Information Step Element Standard Comment I SatlUnsat When 252-1 01 13/CS, A'ux Releases 252-101 13C Feed indicates closed, then when Aux.

Feed indicates 7* release 252-10113C/CS.

closed. Red light lit, green light out. Verifies 10/11 and 20/11 feeds OPEN. Verify 252-1 01 02/CS, 10/11 Feed AND 252- 10106/CS, 20/11 Feed OPEN Acknowledge Alarm 175 Depresses alarm GENl F1 acknowledge pushbutton. Place 225-101 13/SS OFF. Ensure 252-1 01 02/CS, 10/11 Feed AND 252- 101 06/CS, 20/11 Feed in NORMAL AFTER TRIP Reset Alarm 125 GEN 1 Place 243-101/CS, Fast Transfer Select to 10-1 1 Place 225-1 021 3/SS synchronization switch to ON. Inserts synch switch handle and turns clockwise to ON position then releases.

Observes that V/I-UAS and 15 and running voltmeter read V/R-UAS voltages are both approximately 1 IOV. Holds 252-1 021 3/Cs in CLOSE when incoming and running voltages are both approximately 110 and within 8 volts of each other. Releases 252-1021 3/CS Sync Switch 225-101 13/SS 10 synchronization switch to handle OFF Verifies 252-1 01 02/CS and AND 252-10106/CS in NORMAL AFTER TRIP. Depresses Reset l2 F1 Push button. Places 243-101/CS in IO- 11 position.

Refers to Section 4.4. 14* Verify incoming voltmeter approximately 1 1 OV. Close and hold 252-1021 3/CS, Aux Feed. WHEN 252-1 021 3/CS, Aux release 252-1 021 3/CS.

closed. 17* Feed indicates closed, then when AUX. FEED indicates 16* Acknowledge alarm 125 Depress alarm l8 GEN 1 F-24. acknowledge pushbutton.

NRC JPM F - 2008 Limerick Operating Test 5of8 Appendix C 2 Form ES-C-q Performance Information Step Element Standard Comment I SatIUnsat - ~~ __ ~ __ Verify 252-1 02021CS, 1011 2 Feed and 252- 10206/CS, 20/12 Feed open. Place 225-1 021 31SS OFF. Verifies 1011 2 and 2011 2 feeds open. Places 225-1 021 3/SS 20 Synchronization Switch to handle in OFF. Ensure 252-1 0202/CS, 10/12 Feed and 252- NORMAL AFTER TRIP. Verifies 252-1 0202/CS AND 252-102061CS in 21 10206/CS, 2011 2 Feed in NORMAL AFTER TRIP. ~ ~ ~~ __ ~ ~ Place 243-1 021CS, Fast Cue: JPM is complete.

Places 242-1021CS in 20- 22* Transfer Select to 20-12 12 position.

NRC JPM F - 2008 Limerick Operating Test 6of8

___~ - ~ ~~~ ~ Appendix C 3 Form ES-C-'I Verification of Completion Job Performance Measure: NRC JPM F Examinee's Name: Examiner's Name:

-_ Date Performed:

Number of Attempts:

Time to Complete: Question Documentation:

Response:

Result: Satisfactory/Unsatisfactory Examiner's signature and date: NRC JPM F - 2008 Limerick Operating Test 7of8

- Applicant JPM Cue Sheet Initial Conditions:

0 0 GP-2 is being performed on Unit 1 11 and 12 Unit Auxiliary Busses are being powered from offsite sources Initiating Cue: You are directed by Shift Supervision to transfer house loads for Unit 1 to the Unit Aux. Transformer per S91.6.A.

NRC JPM F - 2008 Limerick Operating Test NRC JPM G 2008 Limerick Operating Exam NRC JPM G - 2008 Limerick Operating Test Appendix C Job Performance Measure Form ES-C-'I - Worksheet Facility:

Limerick Task Title: Align RECW For Drywell Cooling Job Performance Measure: NRC JPM G WA

Reference:

400000 K1.02 (3.2, 3.4) E!xaminee:

NRC Examiner:

Date: Method of testing: Si m u I a t ed Perform a n ce : Actual Performance:

X Classroom Simulator X Plant Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied.

Initial Conditions:

0 0 0 0 0 DW Chilled Water has been lost due to trips on both Drywell Chiller Units. The reactor was manually scrammed.

DW temperature is 148°F and rising. DW pressure is 1.8 psig and rising. The CRS has entered T-I 02, Primary Containment Control.

RWCU has been shutdown per S.44.2.A, Reactor Water Cleanup Shutdown.

Initiating Cue: You are directed by Shift Supervision to align RECW operation to cool the drywell, using A Loop first per S13.6.D. Required Materials:

None General

References:

T-I 02, Primary Containment Control Bases, Rev.

22 S13.6.D, RECW Operation with Loss of Drywell Chilled Water, Rev. 14 S44.2.A, Reactor Water Cleanup Shutdown, Rev. 23 ARC-MCR-118-H5, REAC ENCL COOLING WATER HEAD TANK HI/LO LEVEL JPM Origination:

New NRC JPM G - 2008 Limerick Operating Test 2 of 10 Appendix C Job Performance Measure Form ES-C-1 Worksheet Task Standard:

Leaking DW Loop A is isolated from RECW. RECW is aligned to cool the drywell using DW Loop B. Alternate Path: Yes Time Critical:

No Validation Time: 10 minutes JPM Setup Instructions:

Summary Description of JPM: Both drywell chiller units have tripped and efforts to restore have been unsuccessful.

The reactor has been manually scrammed.

Drywell temperature is 148°F and rising. The applicant is directed to align RECW to the A Loop of the drywell chill water system.

When aligned, the Loop will begin leaking inside primary containment. The applicant will recognize multiple indications of RECW leakage and recognize the challenge to the RECW system. The applicant will isolate Loop A Drywell Cooling from RECW and then align RECW to Loop B Drywell Chill Water. JPM is complete when the leak is isolated and the drywell is being cooled by RECW via the B Loop. Simulator Setup:

1. 2. 3. 4. 5. 6. 7. 8. Reset the simulator to any at-power IC Insert Malfunctions MPC482A and MPC482B to trip DW Chillers Manually scram the reactor, take immediate scram actions. Trip both RRPs.

Allow DW temperature to rise to 148°F. Shutdown RWCU per S44.2.A. Set up [malfunctionshemotes to simulate DW Loop leak on RECW, automatically triggered off of switch actions described in SI 3.6.D Step 4.2.8 "PLACE HSS 121A, Loop Drywell Water Source Mode Switch (LOOP), in RE CLG WTR"] a. b. C. d. e. f. Malfunction MPC500B, Drywell Chill Water Leak Loop B (30%) triggered when HSS-87-121A in RE CLG WTR. Remote Function RCW034, RECW Head Tank Drain Valve to OPEN triggered when HSS-87-121A in RE CLG WTR. Time delayed overrides on RECW Head Tank alarm and system pressure instrument, triggered when HSS-87-121A in RE CLG WTR position. Time delayed override on pump motor indicating lights to indicate motor is running. Time delayed override on pump handswitch to stop to simulate pump cavitating and no longer providing flow to system.

Malfunction MCW483A or B to trip the running RECW pump, as appropriate, and remove override on pump indicating lights. Freeze simulator NRC JPM G - 2008 Limerick Operating Test 3 of 10

- Appendix C 2 Form ES-C-1 Perfor ma nce 1 nf orma t i on Critical steps denoted with an asterisk Step Element Standard Comment I Sat/Unsat Obtain a current revision of SI 3.6.D, RECW Operation With Loss of Drywell Chilled Water Obtains a current revision of SI 3.6.0. 2 Reviews precautions.

Reviews precautions.

Cue: If necessary, inform applicant that Precaution 3.1 does not apply to the current plant condition.

Shift manager has confirmed that alignment of RECW cooling to the drywell is required by T- 102. (Step 4.2.1)

Not applicable.

RWCU SHUTDOWN RWCU system already shutdown. system per S44.2.A, Reactor Water Cleanup Cue: Shutdown.

If necessary, inform applicant that RWCU has already been shutdown IAW S44.2.A. (Step 4.2.2) Closes HV-13-102.

CLOSE HV-13-*02, 4* Cooling Water to Reactor Bu i Id i ng I solation (S U PP LY ISOL). (Step 4.2.3) Not applicable IF loss of instrument air prohibits closure of HV *02, SUPPLY ISOL,THEN CLOSE 13-*039, RECW Header Valve to RWCU Non-Regen Heat Exchanger.

NRC JPM G - 2008 Limerick Operating Test 4 of 10 Appendix C 2 Form ES-C-1 Step Element Performance Information Standard Comment / SatlUnsat (Step 4.2.4) Not applicable.

Block CLOSE the following sample point isolation Cue: valves: If asked, a clearance is the sample point isolation.

You are directed to continue.

6 being processed to block HV-51-*F080A, RHR Blocks HV-51-1 F080A Sample Line Downstream closed. Isolation (SAMPLE OUTBOARD) HV-51 -*F080B, Main Blocks HV-51-1 F080B Steam Line Outboard closed.

Sample (SAMPLE OUTBOARD) HV-41 -*F085, RHR Blocks HV-41-1 F085 Sample Line Downstream closed.

Isolation (DRAIN SAMPLE OUTBOARD)

HV-43-*F020, Recirc Blocks HV-43-1 F020 10 Sample Line Outboard closed. Isolation (SAMPLE) 023-1246, FW to Rx Sump Blocks 023-1246 closed.

l1 Is01 Vlv (Step 4.2.5) Directs EO to close Booth operator: CLOSE the following following breakers: Close breakers locally breakers:

D114-R-C-15 using Remote Function 12* D*14-R-C-15 (124A) D114-R-C-19 RPC306.

D*l4-R-C-19 (1 24B) D114-R-C-16 D*l4-R-C-I 6 (1 25A) D114-R-C-20 Report breakers are D*l4-R-C-20 (1 258) closed. (Step 4.2.7) Not applicable.

13 IF required THEN BYPASS isolations Der GP-8.5. NRC JPM G - 2008 Limerick Operating Test 5 of10 Appendix C 2 Form ES-C-11 Performance Information Step Element Standard Comment I SatlUnsat (Step 4.2.8) Places HSS-87-121A in RE Note: PLACE HSS-87-*21A(B), CLG WTR position for The RECW leak into the Loop Drywell Water LOOP A. Verifies valves drywell through the Loop Source Mode Switch indicate flow path open A Drywell Cooling line will (LOOP), in "RE CLG WTR" from RECW and closed be simulated by initiating for loop to be supplied by from Chill Water. a Loop B (not Loop A) RECW AND VERIFY the leak triggered when HSS- 12* following:

87-121A is placed in RE 0 Red indicating lights CLG WTR position.

RECW IN AND RECW OUT Lit 0 Green indicating lights CHLD WTR IN AND CHLD WTR OUT Lit (Step 4.2.9)

Verifies valves open:

VERIFY Drywell Isolation LOOP A HS-87-128 indicating lights DRYWELL OUTLET Lit for loop to be supplied by RECW. Loop A( B) (LOOP) red LOOP B HS-87-122 13 INLET AND DRYWELL LOOP A HS-87-*28 LOOP B HS-87-*22 (Step 4.2. IO) Not applicable.

IF RECW flow is insufficient for adequate 14 cooling, THEN PLACE standby RECW Heat Exchanger in service AND Responds to RECW Head Refers to ARC for Alarm Note: Tank level alarm. Panel 118 Window H-5, THIS BEGINS THE REAC ENCL COOLING ALTERNATE PATH. WATER HEAD TANK HllLO LEVEL. Cue: If necessary, direct applicant to respond to alarms. 15 NRC JPM G - 2008 Limerick Operating Test 6 of 10 Awendix C 2 Form ES-C-I Performance I nf or mat i o n Step Element Standard Comment I SatlUnsat 16 ~ Verify RECW Head Tank 1 OT201 level locally using LG-13-101.

Directs EO to check level locally. Booth operator: Report back as EO that level is 11 inches and lowering approximately 6 inches every 30 seconds. If asked, report that demin water supply valve LV 101 is fully opened. ~~ - ~~ IF losing excessive water inventory, THEN have Operator walkdown system to check for leaks.

Directs EO to walkdown system looking for leaks.

18* ~ __ ~ ~~~~ Recognizes likely leak Isolates the leak from Booth operator:

location is on Loop A of RECW by placing HSS Remove Malfunction for Drywell Cooling and 121A in the DWCW Loop B leak (MPC500B) isolates Loop A Drywell position. after handswitch is Cooling Loop from RECW. returned to DWCW Cue: position.

If necessary, CRS should ask applicant to identify the location of the leak and take necessary actions to isolate and to maintain the RECW system.

Booth operator:

Booth operator:

Report as EO, RECW Head Tank level is rising. Restore normal RECW indications (Head Tank Level Alarm, system pressure).

NRC JPM G - 2008 Limerick Operating Test 7 of 10 Appendix C 2 Form ES-C-'I Perform a nce I n f or mat i o n Step Element Standard Comment I Sat/Unsat (Step 4.2.11)

IF other Drywell Chilled Water loop is needed, *21 B(A), Loop Drywell Water Source Mode Switch (LOOP), in RE CLG WTR AND VERIFY the following:

Red indicating lights RECW IN AND RECW Green indicating lights CHLD WTR IN AND CHLD WTR OUT Lit. Drywell Isolation Loop B(A) (LOOP) red indicating lights DRYWELL INLET

&lJ DRYWELL OUTLET Lit.

THEN PLACE HSS 19" OUT Lit. - LOOP A HS-87-*28 - LOOP B HS-87-*22 Places HSS-87-121 B, Loop Drywell Water Source Mode Switch (LOOP) in RE CLG WTR position and verifies proper indicating lights.

Cue: If necessary, cue the applicant to proceed with establishing drywell cooling by having the CRS ask applicant to report the status of establishing d rywel I cooling with RECW. If necessary, direct applicant to continue with the procedure to establish drywell cooling.

Cue: JPM is complete.

NRC JPM G - 2008 Limerick Operating Test 8 of 10 Appendix C 3 Form ES-C-I Verification of Completion Job Performance Measure:

NRC JPM G Examinee's Name: - Examiner's Name:

Date Performed:

Number of Attempts:

Time to Complete: Question Documentation:

Question:

Response: ~~ ~ ~~ ~ ~~ ~ ~~ Result: SatisfactorylUnsatisfactory Examiner's signature and date:

NRC JPM G - 2008 Limerick Operating Test 9of 10

- - Applicant JPM Cue Sheet Initial Conditions:

0 0 0 0 0 DW Chilled Water has been lost due to trips on both Drywell Chiller Units.

The reactor was manually scrammed.

DW temperature is 148°F and rising. DW pressure is 1.8 psig and rising. The CRS has entered T-102, Primary Containment Control. RWCU has been shutdown per S.44.2.A, Reactor Water Cleanup Shutdown. Initiating Cue:

You are directed by Shift Supervision to align RECW operation to cool the drywell, using A Loop first per SI 3.6.0. NRC JPM G - 2008 Limerick Operating Test NRC JPM H 2008 Limerick Operating Exam NRC JPM H - 2008 Limerick Operating Test Appendix C Job Performance Measure Form ES-C-'I Worksheet

-- Facility: Limerick Task Title: Control Room Ventilation High Radiation Reset Job Performance Measure: NRC JPM H KIA

Reference:

290003 A4.01 (3.2, 3.2) Examinee:

Date: Method of testing: Simulated Performance:

Classroom NRC Examiner:

Actual Performance:

X Simulator X Plant Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues. When you complete the task successfully, the objective for this job performance measure will be satisfied. Initial Conditions: Manual Control Room ventilation high rad isolation was inhibited in response to instrument failure Repairs are complete and all rad alarms are clear Initiating Cue:

You are directed by Shift Supervision to reset the Control room HVAC high radiation isolations per S78.7.A Required Materials:

None General

References:

S78.7.A, Control Room HVAC system Restoration from an Isolation, Revision 14 JPM Origination: Limerick Bank JPM 74, Rev. 01 1 Task Standard:

Control room HVAC High Radiation isolation reset with CREFAS aligned for normal automatic operation Alternate Path: No Time Critical:

No Validation Time: 15 minutes JPM Setup Instructions:

NRC JPM H - 2008 Limerick Operating Test 2of7 Appendix C Job Performance Measure Worksheet Form ES-C-% Simulator Setup:

1. 2. 3. 4. 5. 6. 7. 8. Place the HS-78-017A,B,C and D keylock switches to RESET Rotate the arming collars for HSS-78-017A,B,C and D to RAD. Place the HS-78-017A,B,C and S keylock switches to AUTO Depress the pushbuttons on HSS-78-017A,B,C and D Leave HSS-078-017A,B,C, and D collars in RAD Ensure the HI RAD ISLN light lit and the CHLOR ISLN NOT lit for all four isolation channels.

Remove the four PA2235 keys from HS-78-017A,B,C and D. Reset any annunciators that will reset NRC JPM H - 2008 Limerick Operating Test 3 of7 Appendix C 2 Form ES-C-'I Performance Information Critical steps denoted with an asterisk Step Element Standard Comment I Sat/Unsat IF required THEN manually NIA ACKNOWLEDGE chlorine detectors locally at detector (625-08-350).

IF required, THEN RESET toxic chemical alarms per S78.1 .F, Alignment of Toxic Chemical Detection System for Normal Operation.

NIA ~ - IF required, THEN NIA ACKNOWLEDGE radiation condition by de pres sing ACK on RM-11 console, MCR. 3 PLACE the following control room Isolation Valve Reset keylock Switches to "RESET": NIA HS-78-017C, RESET C Places HS-78-017C is in RESET 4a * ~ ~~ ~~ ~~~~~

HS-78-017A, RESET A HS-78-017B, RESET 6 Places HS-78-017A is in RESET Places HS-78-017B is in RESET 4b* 4c* ~ HS-78-017D, RESET D Places HS-78-017D IS in RESET ENSURE the following NIA Note: collar left in RAD control room Isolation valve per Main Rad Isolation 5 Trip Switches to "NOR": procedure S78.8.A.

Not critical to enable reset but required by procedure 4d

• HSS-78-017C, TRIP C Places HSS-78-017C in NOR 5a HSS-78-017C, TRIP A 5b Places HSS-78-017A in NOR HSS-78-017C, TRIP B 5c Places HSS-78-017B in NOR NRC JPM H - 2008 Limerick Operating Test 4of7 Appendix C 2 Form ES-C-'I Performance Information SteD Element Standard Comment I Sat/Unsat HSS-78-017C, TRIP D 5d Places HSS-78-017D in NOR ~ ~~~~ PLACE the following N/A Control Room Isolation Valve Reset Keylock Switches to AUTO: HS-78-017C, RESET C HS-78-017C, RESET A HS-78-017C, RESET B HS-78-017C, RESET D Places HS-78-017C in AUTO Places HS-78-017A in AUTO Places HS-78-0178 in AUTO Places HS-78-017D in AUTO 6a 6b 6c 6d ~~~ ~ VERIFY status of N/A AIR FAN A (B) as follows If a single subsystem N/A isolation remains, THEN verify OAVl27 or OB1 27 is running as appropriate If all subsystems reset, THEN verify OAVl27 and OB127 are NOT running 7 OA(B)VI 27, EMERGENCY 7a OAVl27 and OBVl27 are not running. (Cue: you can stop here. You have met the termination criteria for this JPM) 7b NRC JPM H - 2008 Limerick Operating Test 5of7 Appendix C 3 Form ES-C-1 Verification of Completion Job Performance Measure:

NRC JPM H Examinee's Name: - Examiner's Name: - Date Performed:

Number of Attempts:

Time to Complete: Question Documentation:

Question:

Response: Res u It : Satisfactory/

U n s a t i sf a c t o r y Examiner's signature and date:

NRC JPM H - 2008 Limerick Operating Test 6 of7 Applicant JPM Cue Sheet Initial Conditions: Manual Control Room ventilation high rad isolation was inhibited in response to instrument failure Repairs are complete and all rad alarms are clear Initiating Cue: You are directed by Shift Supervision to reset the Control room HVAC high radiation isolations per S78.7.A. All prerequisites are met. NRC JPM H - 2008 Limerick Operating Test NRC JPM I 2008 Limerick Operating Exam NRC JPM I - 2008 Limerick Operating Test Form ES-C-'I Appendix C Job Performance Measure Worksheet

_- Facility: Limerick Task Title:

Alt Injection From The Fire System K/A

Reference:

295031 EA1.08 (3.8, 3.9) Examinee: NRC Examiner: Job Performance Measure:

NRC JPM I Date: Method of testing:

Simulated Performance:

X Actual Performance: Classroom Simulator Plant X Read to the examinee:

I will explain the initial conditions, which steps t simulate or di uss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied. Initial Conditions:

Unit 2 reactor level is low and injection is being established Reactor pressure is 50 psig The Motor Driven Fire Pump is out of service and unavailable Initiating Cue:

Shift Supervision directs you to perform T-244 to supply Fire Water to increase Unit 2 reactor level. Required Materials: BL-840 Key for T-225 Hose Storage Cabinet (475-R17-253) General

References:

T-244, Alternate Injection from the Fire System, Rev. 14 JPM Origination: Limerick Bank JPM 260, Rev. 006 Task Standard: Backup Diesel Driven Fire Pump started locally. Alternate Path:

No Time Critical:

No Validation Time: 23 min JPM Setup Instructions: NRC JPM I - 2008 Limerick Operating Test 2 of6 Appendix C 2 Form ES-C-1 "_ Performance Information Critical steps denoted with an asterisk Step Element Standard Comment / SatlUnsat 1 Obtain current revision of Unit 2 T-244. T-244 obtained.

Current revision of Unit 2 2 Obtain necessary Necessary tools/equipment Tools/Equipment from Unit obtained.

2 T-225 Hose Storage Cabinet(475-R17-253), BL- 840 key required.

Cue: You have the necessary tools/equipment in your possession. CONNECT hose at 51- 21 79 2A RHWFire Protection Interconnection Drain Vlv. AND ROUTE to drain THEN CYCLE 51- 2179 open AND closed to ensure pipe vented. Connects hose at 51-2179 AND routes to drain.

51-21 79 cycled to vent pipe. 3* Cue: Connected as described. CONNECT hose at 22- 2430 Fire Protection/RHR Interconnection Isolation Vlv AND ROUTE to drain Connects hose at 22-2430 AND routes to drain. 22-2430 cycled to vent pipe. THEN CYCLE 22-2430 4* open AND closed to ensure pipe vented.

Cue: Connected as described. CONNECT hose to fitting downstream of 22-2429, Fire ProtectiodRHR 2429. Interconnection Isolation Connects one end of hose to downstream side of 22- 5* Valve. Cue: Connected as described.

NRC JPM I - 2008 Limerick Operating Test 3 of6 Appendix C 2 Form ES-C Perform an ce I n f orm a t i o n Step Element Standard Comment I SatlUnsat CONNECT other end of hose to 51-2178, 2A RHR Fire Protection Crosstie Connect ion kola t ion Va Ive . Connects other end of hose to 51-2178. 6* Cue: Connected as described. OPEN 22-2429 Turns 22-2429 handwheel Cue: Valve handwheel clockwise direction and StODS. f u II y counterclockwise . 7* turns in the counter- UNLOCK AND OPEN 51- 21 78 fully counterclockwise.

8* Cue: Handwheel turns in counterclockwise direction and stops. Turns 51-2178 handwheel START available Fire Not Applicable Pump: ~- ~~~ - - ~ ~~ IF starting OOP512, Motor Driven Fire Pump, THEN DEPRESS HS-22-002-1 at OOC650 (Main Control starts. Recognize from task conditions that the Motor Driven Fire Pump is unavailable and proceed to 10 Room) AND VERIFY pump Step 4.2.2. Cue: If asked, reply that MDFP is not available. IF starting OOP511, Diesel Driven Fire Pump, THEN DEPRESS HS-22-6-1 at DDFP. OOC650 (Main Control Room) AND VERIFY pump is running. Contacts main control room and requests start of Cue: MCR reports the Diesel Driven Fire Pump is running Cue: JPM is complete.

NRC JPM I - 2008 Limerick Operating Test 4 of 6 Appendix C 3 Form ES-C-1 .- Verification of Completion Job Performance Measure:

NRC JPM I Examinee's Name: - Examiner's Name: - Date Performed:

Number of Attempts:

Time to Complete:

Question Documentation:

Question:

Response:

Result: Satisfactory/Unsatisfactory Examiner's signature and date: NRC JPM I - 2008 Limerick Operating Test 5 of6 Applicant JPM Cue Sheet Initial Conditions:

0 0 0 Unit 2 reactor level is low and injection is being established Reactor pressure is 50 psig The Motor Driven Fire Pump is out of service and unavailable Initiating Cue: Shift Supervision directs you to perform T-244 to supply Fire Water to increase Unit 2 reactor level.

NRC JPM I - 2008 Limerick Operating Test NRC JPM J 2008 Limerick Operating Exam NRC JPM J - 2008 Limerick Operating Test Appendix C Job Performance Measure Form ES-C-I Worksheet

-- Facility:

Limerick Task Title: Transfer RWST to CST KIA

Reference:

203000 A2.04 (3.5, 3.6) Examinee: Job Performance Measure: NRC JPM J NRC Examiner:

Date: Method of testing: Simulated Performance:

X Actual Performance:

Classroom Simulator Plant X Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues.

When you complete the task successfully, the objective for this job performance measure will be satisfied.

Initial Conditions:

A station blackout has occurred. Procedure E-I, Loss of All AC Power (Station Blackout), is being implemented. Initiating Cue:

You are directed to initiate gravity feed from the RWST to #I CST in accordance with E-I, Step 3.20. There is sufficient RWST inventory for this transfer.

Required Materials:

Pages from E-I, Loss of All AC Power (Station Blackout) containing Step 3.20. General

References:

E-I, Loss of All AC Power (Station Blackout), Rev.

033 JPM Origination:

New Task Standard:

Initiate gravity feed from the U1 RWST to the U1 CST. Alternate Path:

No Time Critical:

No Validation Time: 5 min JPM Setup Instructions:

None NRC JPM J - 2008 Limerick Operating Test 2of5 Appendix C 2 Form ES-C-'1 Perfor ma nce I n f or mat ion Critical steps denoted with an asterisk Step Element Standard Comment

/ SatlUnsat

~ ENSURE 08-0008 closed.

Cue: Valve is closed. Verifies 08-0008 is closed.

1 ENSURE 08-0029 closed.

Cue: Valve is closed. ALIGN the following Not applicable valves: Verifies 08-0029 is closed. 2 _- 3 1. 08-0001, Tie Between Opens 08-0001.

RWST and Manifold - 4* OPEN Cue: Valve is open.

2. 08-0003, Tie Between Opens 08-0003. #I CST and Manifold 5* - OPEN Cue: Valve is open. 3. 08-0004, Manifold Opens 08-0004. Stop Valve - OPEN 6* Cue: Valve is open. You hear flow noise. Inform control room that gravity feed has been initiated from RWST to #I CST. Cue: JPM is comdete. Informs control room. NRC JPM J - 2008 Limerick Operating Test 3 of 5 Appendix C 3 Form ES-C-'I Verification of Completion Job Performance Measure:

NRC JPM J Examinee's Name:

-- Examiner's Name: -- Date Performed:

Number of Attempts:

Time to Complete: Question Documentation:

Question:

Response:

Result: Satisfactory/Unsatisfactory Examiner's signature and date: NRC JPM J - 2008 Limerick Operating Test 4of."

Applicant JPM Cue Sheet Initial Conditions:

A station blackout has occurred. Procedure E-I , Loss of All AC Power (Station Blackout), is being implemented.

Initiating Cue: You are directed to initiate gravity feed from the RWST to #I CST in accordance with E-I , Step 3.20. There is sufficient RWST inventory for this transfer.

NRC JPM J - 2008 Limerick Operating Test NRC JPM K 2008 Limerick Operating Exam NRC JPM K - 2008 Limerick Operating Test Job Performance Measure Form ES-C-I Appendix C Worksheet Facility: Limerick Task Title: Supply Emer Power to RClC Isolation Job Performance Measure: NRC JPM K WA

Reference:

600000 AK3.04 (2.8, 3.4) Examinee:

NRC Examiner:

Date: Method of testing: Simulated Performance:

X Actual Performance: Classroom Simulator Plant X Read to the examinee:

I will explain the initial conditions, which steps to simulate or discuss, and provide initiating cues. When you complete the task successfully, the objective for this job performance measure will be satisfied.

I nitia I Conditions:

A fire in the Main Control Room has required evacuation and control of the plant from the RSP. Division 3 power is not available.

RClC is required but has failed to inject. HV-49-2F007, RClC Main Steam Supply Inboard PClV has NO position indication. Personnel are stationed at the RSP.

0 0 0 0 Initiating Cue:

You are directed to supply Div 1 power to HV-49-2F007, in preparation for placing Unit 2 RClC in service from the RSP in accordance with SE-1, Section 4.3.8 Reactor Level Control. Required Materials: SE-1, Remote Shutdown, Pages 14 & 15, Step 4.3.8 General

References:

SE-1, Remote Shutdown, Rev.

59 JPM Origination: Limerick Bank JPM 0250, Rev. 007 Task Standard:

Division 1 power supplied to HV-49-2F007, RClC Main Steam Supply Inboard PClV Alternate Path: No Time Critical: No Validation Time: 5 min NRC JPM K - 2008 Limerick Operating Test 20f8 Appendix C Job Performance Measure Form ES-C-1 Worksheet JPM Setup Instructions:

Inform Unit 2 Main Control Room that Terminal Box 20TB49-2F007 will be opened for training. Ensure locked valve entry is made. NRC JPM K - 2008 Limerick Operating Test 3 of8 Appendix C 2 Form ES-C-1 Performance Information Critical steps denoted with an asterisk Step Element Standard Comment

/ Sat/Unsat ~~ ~ Obtain current revision of SE-1, Remote Shutdown.

Cue: Provide a copy of SE-1 CAUTION Steps 4.3.8.1 through 4.3.8.7 are Prompt Actions, requiring completion within 14 minutes. Not applicable 1 NOTE Step 4.3.8 indicates HV- 49-*F007 has failed closed. - IF the following conditions exist: Div 3 power has been disrupted RClC fails to inject on manual auto start signal HV-49-*F007 has no position indica tion - THEN PERFORM the following to supply Div 1 power to HV-49-2F007, - AND PLACE RClC in service: (Step 4.3.8.1) Opens D234-R-E-13 (Unit OPEN D*34-R-E-13. (Unit 2: 475-R13-253) 1 : 402-R15-253, Unit 2: 3* 475-R13-253).

Cue: D234-R-E-13 is 0136317. NRC JPM K - 2008 Limerick Operating Test 4of8 Atmendix C 2 Form ES-C-1 Performance Information Step Element Standard Comment I SatlUnsat NOTE Obtains a screwdriver and A screwdriver AND LV-*00 LV-200 key. SIMULATES key are required for step unlocking and opening 4.3.8.2. Terminal Box 20TB49- 2F007 (Unit 2: 475-R14- (Step 4.3.8.2) 253). UNLOCK AND OPEN 4* terminal box *OTB49- Cue: *F007 Terminal box is unlocked (Unit 1: 402-R15-253, Unit and opened.

Cue: If asked, inform applicant that both lamps are out in the cabinet.

2: 475-R14-253).

Note: Normal power is de- energized (the reason for the task) and the alternate power supply breaker has not been closed yet).

The lamps indicate the status of power just upstream of the molded case breakers in the cabinet. (Step 4.3.8.3) Places 43-CB22313, Note: PLACE 43-CB22313, Manual Transfer Switch in USE PHOTO of cabinet. Manual Transfer Switch EMERGENCY. Applicant Do not open cabinet. (located in terminal box simulates pulling down on *OTB491 *F007), the red handle lever.

in EMERGENCY.

5* Cue: Switch is in the DOWN position.

Cue: If asked, lights remain OUT. (Step 4.3.8.4) Unlocks and closes D214-UNLOCK R-C-31, RClC Main Steam AND CLOSE D*14-R-C-31, Inboard PClV RClC Main Steam lnbd 6* PClV (EMERGENCY (Unit 2: 580-R17-283)

POWER). (Unit 1: 506- R11-283 Unit 2: 580-R17-Cue: 283) D214-R-C-31 is closed. (EMERGENCY POWER) (Step 4.3.8.5) OPEN HV-49-*F007 Calls operator at 20C201 and directs him to open (INBOARD) at *OC201 HV-49-2F007.

7* Cue: Operator reports HV 2F007 is open.

NRC JPM K - 2008 Limerick Operating Test 5of8 Appendix C 2 Form ES-C-I Step Element Performance Information Standard Comment I SatlUnsat (Step 4.3.8.6) Locks open D214-R-C-31 LOCK OPEN D*14-R-C-3II Cue: D214-R-C-31 is open. 8* 9* (Step 4.3.8.7) Returns 43-CB22313, RETURN 43-CB22313, Manual Transfer Switch, NORMAL. to NORMAL. Manual Transfer Switch, to Cue: 43-CB22313, Manual Transfer Switch is in the UP position.

Cue: Both lights are still out. Informs operator at RSP that procedure directs Step 4.3.3. (Step 4.3.8.8) PLACE RCIC in service lo* per step 4.3.3 placing RCIC in service per Cue: JPM is complete.

NRC JPM K - 2008 Limerick Operating Test 6of8 Appendix C 3 Form ES-C-1 Verification of Completion Job Performance Measure: NRC JPM K Examinee's Name: Examiner's Name: Date Performed:

Number of Attempts:

Time to Complete: Question Documentation:

Question: - ~ ~~ Response: - ~ ~ ~ ~ ~~ ~~ Result: Satisfactory/Unsatisfactory Examiner's signature and date:

NRC JPM K - 2008 Limerick Operating Test 7 of8 Applicant JPM Cue Sheet Initial Conditions:

0 0 0 0 0 A fire in the Main Control Room has required evacuation and control of the plant from the RSP.

Division 3 power is not available.

RClC is required but has failed to inject. HV-49-2F007, RClC Main Steam Supply Inboard PClV has NO position indication.

Personnel are stationed at the RSP. Initiating Cue: You are directed to supply Div 1 power to HV-49-2F007, in preparation for placing Unit 2 RClC in service from the RSP in accordance with SE-1, Section 4.3.8 Reactor Level Control. NRC JPM K - 2008 Limerick Operating Test