ML14120A337: Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(Created page by program invented by StriderTol)
Line 16: Line 16:


=Text=
=Text=
{{#Wiki_filter:CY-TM-1 70-300Exelon. Revision 3Page 1 of 209Nuclear Level 3 -Information UseOFFSITE DOSE CALCULATION MANUAL (ODCM)INTRODUCTION The OFFSITE DOSE CALCULATION MANUAL (ODCM) is a supporting document of theThree Mile Island Nuclear Station (TMI) Unit 1 and Unit 2 PDMS Technical Specifications andimplements TMI radiological effluent controls.
{{#Wiki_filter:CY-TM-1 70-300 Exelon. Revision 3 Page 1 of 209 Nuclear Level 3 -Information Use OFFSITE DOSE CALCULATION MANUAL (ODCM)INTRODUCTION The OFFSITE DOSE CALCULATION MANUAL (ODCM) is a supporting document of the Three Mile Island Nuclear Station (TMI) Unit 1 and Unit 2 PDMS Technical Specifications and implements TMI radiological effluent controls.
The ODCM contains the controls, bases, andsurveillance requirements for liquid and gaseous radiological effluents.
The ODCM contains the controls, bases, and surveillance requirements for liquid and gaseous radiological effluents.
In addition, the ODCMdescribes the methodology and parameters to be used in the calculation of off-site doses dueto radioactive liquid and gaseous effluents.
In addition, the ODCM describes the methodology and parameters to be used in the calculation of off-site doses due to radioactive liquid and gaseous effluents.
This document also describes the methodology used for calculation of the liquid and gaseous effluent monitoring instrumentation alarm/trip setpoints. Liquid and Gaseous Radwaste Treatment System configurations are also included.
This document also describes the methodology used for calculation of the liquid and gaseous effluent monitoring instrumentation alarm/trip set points. Liquid and Gaseous Radwaste Treatment System configurations are also included.The ODCM also is used to define the requirements for the TMI radiological environmental monitoring program (REMP) and contains a list and graphical description of the specific sample locations used in the REMP.The ODCM is maintained at the Three Mile Island (TMI) site for use as a reference guide and training document of accepted methodologies and calculations.
The ODCM also is used to define the requirements for the TMI radiological environmental monitoring program (REMP) and contains a list and graphical description of the specificsample locations used in the REMP.The ODCM is maintained at the Three Mile Island (TMI) site for use as a reference guide andtraining document of accepted methodologies and calculations.
Changes in the calculation methods or parameters will be incorporated into the ODCM to ensure the ODCM represents the present methodology in all applicable areas. Changes to the ODCM will be implemented in accordance with the TMI-1 and TMI-2 PDMS Technical Specifications.
Changes in the calculation methods or parameters will be incorporated into the ODCM to ensure the ODCM represents the present methodology in all applicable areas. Changes to the ODCM will be implemented inaccordance with the TMI-1 and TMI-2 PDMS Technical Specifications.
The ODCM follows the methodology and models suggested by NUREG-0133, and Regulatory Guide 1.109, Revision 1 for calculation of off-site doses due to plant effluent releases.Simplifying assumptions have been applied in this manual where applicable to provide a more workable document for implementation of the Radiological Effluent Controls requirements.
The ODCM follows the methodology and models suggested by NUREG-0133, and Regulatory Guide 1.109, Revision 1 for calculation of off-site doses due to plant effluent releases.
TMI implements the TMI Radiological Effluent Controls Program and Regulatory Guide 1.21, Revision 1 (Annual Radioactive Effluent Release Report) requirements by use of a computerized system used to determine TMI effluent releases and to update cumulative effluent doses.This procedure replaces 6610-PLN-4200.01.
Simplifying assumptions have been applied in this manual where applicable to provide a moreworkable document for implementation of the Radiological Effluent Controls requirements.
CY-TM-1 70-300 Revision 3 Page 2 of 209 TABLE OF CONTENTS PART I TMI-1 RADIOLOGICAL EFFLUENT CONTROLS Section Page 1.0 DEFINITIONS 13 Table 1-1, Frequency Notation 18 Map1.1, Gaseous Effluent Release Points and Liquid Effluent Outfall Locations 19 2.0 RADIOLOGICAL EFFLUENT CONTROLS AND BASES 20 2.1 Radioactive Effluent Instrumentation 20 2.1.1 Radioactive Liquid Effluent Instrumentation 20 Table 2.1-1, Radioactive Liquid Effluent Instrumentation 22 2.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 23 Table 2.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation 24 2.2 Radioactive Effluent Controls 30 2.2.1 Liquid Effluent Controls 30 2.2.2 Gaseous Effluent Controls 34 2.2.3 Total Radioactive Effluent Controls 41 3.0 SURVEILLANCES 44 3.1 Radioactive Effluent Instrumentation 44 3.1.1 Radioactive Liquid Effluent Instrumentation 44 Table 3.1-1, Radioactive Liquid Effluent Monitoring Instrumentation Surveillance Requirements 45 3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 47 Table 3.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 48 CY-TM-170-300 Revision 3 Page 3 of 209 TABLE OF CONTENTS (Cont'd)PART I TMI-1 RADIOLOGICAL EFFLUENT CONTROLS Section Page 3.2 Radiological Effluents 53 3.2.1 Liquid Effluents 53 Table 3.2-1, Radioactive Liquid Waste Sampling and Analysis Program 55 3.2.2 Gaseous Effluents 58 Table 3.2-2, Radioactive Gaseous Waste Sampling and Analysis Program 60 3.2.3 Total Radioactive Effluents 64 4.0 PART I REFERENCES 65 CY-TM-1 70-300 Revision 3 Page 4 of 209 TABLE OF CONTENTS (Cont'd)PART II TMI-2 RADIOLOGICAL EFFLUENT CONTROLS Section Page 1.0 DEFINITIONS 67 Table 1.1, Frequency Notation 70 2.0 CONTROLS AND BASES 71 2.1 Radioactive Effluent Instrumentation 71 2.1.1 Radioactive Liquid Effluent Instrumentation 71 2.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 71 Table 2.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation 73 2.2 Radioactive Effluent Controls 74 2.2.1 Liquid Effluent Controls 74 2.2.2 Gaseous Effluent Controls 78 2.2.3 Total Radioactive Effluent Controls 85 3.0 SURVEILLANCES 87 3.1 Radioactive Effluent Instrumentation 87 3.1.1 Radioactive Liquid Effluent Instrumentation 87 3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 87 Table 3.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 88 3.2 Radioactive Effluents 89 3.2.1 Liquid Effluents 89 Table 3.2-1, Radioactive Liquid Waste Sampling and Analysis Program 90 3.2.2 Gaseous Effluents 91 CY-TM-170-300 Revision 3 Page 5 of 209 TABLE OF CONTENTS (Cont'd)PART II TMI-2 RADIOLOGICAL EFFLUENT CONTROLS Section Paqe Table 3.2-2, Radioactive Gaseous Waste Sampling and Analysis Program 92 3.2.3 Total Radioactive Effluents 95 4.0 PART II REFERENCES 96 CY-TM-170-300 Revision 3 Page 6 of 209 TABLE OF CONTENTS (Cont'd)PART III EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES Section Pagqe 1.0 LIQUID EFFLUENT MONITORS 98 1.1 TMI-1 and TMI-2 Liquid Radiation Monitor Set Points 98 1.2 TMI Liquid Effluent Release Points and Liquid Radiation Monitor Data 99 1.3 Control of Liquid Releases 101 2.0 LIQUID EFFLUENT DOSE ASSESSMENT 106 2.1 Liquid Effluents  
TMI implements the TMI Radiological Effluent Controls Program and Regulatory Guide 1.21,Revision 1 (Annual Radioactive Effluent Release Report) requirements by use of acomputerized system used to determine TMI effluent releases and to update cumulative effluent doses.This procedure replaces 6610-PLN-4200.01.
-10 CFR 50 Appendix I 106 2.2 TMI Liquid Radwaste System Dose Calcs Once Per Month 107 2.3 Alternative Liquid Dose Calculational Methodology 108 3.0 TMI LIQUID EFFLUENT WASTE TREATMENT SYSTEM 113 3.1 TMI-1 Liquid Effluent Waste Treatment System 113 3.2 Operability of the TMI-1 Liquid Effluent Waste Treatment System 114 3.3 TMI-2 Liquid Effluent Waste Treatment System 114 4.0 GASEOUS EFFLUENT MONITORS 117 4.1 TMI-1 Noble Gas Monitor Set Points 117 4.2 TMI-1 Particulate and Radioiodine Monitor Set Points 119 4.3 TMI-2 Gaseous Radiation Monitor Set Points 120 4.4 TMI-1 Gaseous Effluent Release Points and Gaseous Radiation Monitor Data 121 4.5 TMI-2 Gaseous Effluent Release Points and Gaseous Radiation Monitor Data 123 4.6 Control of Gaseous Effluent Releases 124 CY-TM-1 70-300 Revision 3 Page 7 of 209 TABLE OF CONTENTS (Cont'd)PART III EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES Section Page 5.0 GASEOUS EFFLUENT DOSE ASSESSMENT 136 5.1 Gaseous Effluents  
CY-TM-1 70-300Revision 3Page 2 of 209TABLE OF CONTENTSPART I TMI-1 RADIOLOGICAL EFFLUENT CONTROLSSection Page1.0 DEFINITIONS 13Table 1-1, Frequency Notation 18Map1.1, Gaseous Effluent Release Points and Liquid Effluent Outfall Locations 192.0 RADIOLOGICAL EFFLUENT CONTROLS AND BASES 202.1 Radioactive Effluent Instrumentation 202.1.1 Radioactive Liquid Effluent Instrumentation 20Table 2.1-1, Radioactive Liquid Effluent Instrumentation 222.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 23Table 2.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation 242.2 Radioactive Effluent Controls 302.2.1 Liquid Effluent Controls 302.2.2 Gaseous Effluent Controls 342.2.3 Total Radioactive Effluent Controls 413.0 SURVEILLANCES 443.1 Radioactive Effluent Instrumentation 443.1.1 Radioactive Liquid Effluent Instrumentation 44Table 3.1-1, Radioactive Liquid Effluent Monitoring Instrumentation Surveillance Requirements 453.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 47Table 3.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 48 CY-TM-170-300 Revision 3Page 3 of 209TABLE OF CONTENTS (Cont'd)PART I TMI-1 RADIOLOGICAL EFFLUENT CONTROLSSection Page3.2 Radiological Effluents 533.2.1 Liquid Effluents 53Table 3.2-1, Radioactive Liquid Waste Sampling and Analysis Program 553.2.2 Gaseous Effluents 58Table 3.2-2, Radioactive Gaseous Waste Sampling and Analysis Program 603.2.3 Total Radioactive Effluents 644.0 PART I REFERENCES 65 CY-TM-1 70-300Revision 3Page 4 of 209TABLE OF CONTENTS (Cont'd)PART II TMI-2 RADIOLOGICAL EFFLUENT CONTROLSSection Page1.0 DEFINITIONS 67Table 1.1, Frequency Notation 702.0 CONTROLS AND BASES 712.1 Radioactive Effluent Instrumentation 712.1.1 Radioactive Liquid Effluent Instrumentation 712.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 71Table 2.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation 732.2 Radioactive Effluent Controls 742.2.1 Liquid Effluent Controls 742.2.2 Gaseous Effluent Controls 782.2.3 Total Radioactive Effluent Controls 853.0 SURVEILLANCES 873.1 Radioactive Effluent Instrumentation 873.1.1 Radioactive Liquid Effluent Instrumentation 873.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 87Table 3.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 883.2 Radioactive Effluents 893.2.1 Liquid Effluents 89Table 3.2-1, Radioactive Liquid Waste Sampling and Analysis Program 903.2.2 Gaseous Effluents 91 CY-TM-170-300 Revision 3Page 5 of 209TABLE OF CONTENTS (Cont'd)PART II TMI-2 RADIOLOGICAL EFFLUENT CONTROLSSection PaqeTable 3.2-2, Radioactive Gaseous Waste Sampling and Analysis Program 923.2.3 Total Radioactive Effluents 954.0 PART II REFERENCES 96 CY-TM-170-300 Revision 3Page 6 of 209TABLE OF CONTENTS (Cont'd)PART III EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES Section Pagqe1.0 LIQUID EFFLUENT MONITORS 981.1 TMI-1 and TMI-2 Liquid Radiation Monitor Set Points 981.2 TMI Liquid Effluent Release Points and Liquid Radiation Monitor Data 991.3 Control of Liquid Releases 1012.0 LIQUID EFFLUENT DOSE ASSESSMENT 1062.1 Liquid Effluents  
-Instantaneous Release Limits 136 5.1.1 Noble Gases 136 5.1.1.1 Total Body 136 5.1.1.2 Skin 137 5.1.2 lodines, Tritium and Particulates 138 5.2 Gaseous Effluents  
-10 CFR 50 Appendix I 1062.2 TMI Liquid Radwaste System Dose Calcs Once Per Month 1072.3 Alternative Liquid Dose Calculational Methodology 1083.0 TMI LIQUID EFFLUENT WASTE TREATMENT SYSTEM 1133.1 TMI-1 Liquid Effluent Waste Treatment System 1133.2 Operability of the TMI-1 Liquid Effluent Waste Treatment System 1143.3 TMI-2 Liquid Effluent Waste Treatment System 1144.0 GASEOUS EFFLUENT MONITORS 1174.1 TMI-1 Noble Gas Monitor Set Points 1174.2 TMI-1 Particulate and Radioiodine Monitor Set Points 1194.3 TMI-2 Gaseous Radiation Monitor Set Points 1204.4 TMI-1 Gaseous Effluent Release Points and Gaseous Radiation MonitorData 1214.5 TMI-2 Gaseous Effluent Release Points and Gaseous Radiation MonitorData 1234.6 Control of Gaseous Effluent Releases 124 CY-TM-1 70-300Revision 3Page 7 of 209TABLE OF CONTENTS (Cont'd)PART III EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES Section Page5.0 GASEOUS EFFLUENT DOSE ASSESSMENT 1365.1 Gaseous Effluents  
-10 CFR 50 Appendix I 139 5.2.1 Noble Gases 139 5.2.2 lodines, Tritium and Particulates 140 5.3 Gaseous Radioactive System Dose Calculations Once per Month 142 5.4 Alternative Gaseous Dose Calculational Methodology 143 6.0 TMI-1 GASEOUS EFFLUENT WASTE TREATMENT SYSTEM 165 6.1 Description of the TMI-1 Gaseous Radwaste Treatment System 165 6.2 Operability of the TMI-1 Gaseous Radwaste Treatment System 165 7.0 EFFLUENT TOTAL DOSE ASSESSMENT 167 8.0 TMINS RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM (REMP) 168 8.1 Monitoring Program Requirements 168 8.2 Land Use Census 171 8.3 Interlaboratory Comparison Program 173 9.0 PART III REFERENCES 191 CY-TM-1 70-300 Revision 3 Page 8 of 209 TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART III Section TABLES Table 1.1 Table 1.2 Table 2.1 Table 2.2 Table 4.1 Table 4.2 Table 4.3 Table 4.4 Table 4.5 Table 4.6 Table 5.2.1 Table 5.2.2 Table 5.2.3 Table 5.2.4 Table 5.3.1 Table 5.4.1 Table 5.4.2 Table 5.4.3 Table 5.4.4 Table 5.5.1 Paqe TMI Liquid Release Point and Liquid Radiation Monitor Data TMI-2 Sump Capacities Liquid Dose Conversion Factors (DCF): DFij Bioaccumulation Factors, BFi TMI-1 Gaseous Release Point and Gaseous Radiation Monitor Data TMI-2 Gaseous Release Point and Gaseous Radiation Monitor Data Dose Factors for Noble Gases and Daughters Atmospheric Dispersion Factors for Three Mile Island -Station Vent Atmospheric Dispersion Factors for Three Mile Island -Ground Release Dose Parameters for Radioiodines and Radioactive Particulate In Gaseous Effluents Pathway Dose Factors, Ri -Infant, Inhalation Pathway Dose Factors, Ri -Child, Inhalation Pathway Dose Factors, Ri -Teen, Inhalation Pathway Dose Factors, Ri -Adult, Inhalation Pathway Dose Factors, Ri -All Age Groups, Ground Plane Pathway Dose Factors, Ri -Infant, Grass-Cow-Milk Pathway Dose Factors, R -Child, Grass-Cow-Milk Pathway Dose Factors, Ri -Teen, Grass-Cow-Milk Pathway Dose Factors, Ri -Adult, Grass-Cow-Milk Pathway Dose Factors, Ri -Infant, Grass-Goat-Milk 102 103 109 112 125 126 127 128 129 130 144 145 146 147 148 149 150 151 152 153 CY-TM-1 70-300 Revision 3 Page 9 of 209 TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART III Section TABLES Table 5.5.2 Table 5.5.3 Table 5.5.4 Table 5.6.1 Table 5.6.2 Table 5.6.3 Table 5.6.4 Table 5.7.1 Table 5.7.2 Table 5.7.3 Table 5.7.4 Table 8.1 Table 8.2 Table 8.3 Table 8.4 Table 8.5 Table 8.6 Table 8.7 Table 8.8 Table 8.9 Table 8.10 Paaqe Pathway Dose Factors, Ri -Child, Grass-Goat-Milk Pathway Dose Factors, Ri -Teen, Grass-Goat-Milk Pathway Dose Factors, Ri -Adult, Grass-Goat-Milk Pathway Dose Factors, Ri -Infant, Grass-Cow-Meat Pathway Dose Factors, Ri -Child, Grass-Cow-Meat Pathway Dose Factors, R i -Teen, Grass-Cow-Meat Pathway Dose Factors, Ri -Adult, Grass-Cow-Meat Pathway Dose Factors, Ri -Infant, Vegetation Pathway Dose Factors, R 1 -Child, Vegetation Pathway Dose Factors, Ri -Teen, Vegetation Pathway Dose Factors, Ri -Adult, Vegetation Sample Collection and Analysis Requirements Reporting Levels for Radioactivity Concentrations in Environmental Samples Detection Capabilities for Environmental Sample Analysis TMINS REMP Station Locations  
-Instantaneous Release Limits 1365.1.1 Noble Gases 1365.1.1.1 Total Body 1365.1.1.2 Skin 1375.1.2 lodines, Tritium and Particulates 1385.2 Gaseous Effluents  
-Air Particulate and Air Iodine TMINS REMP Station Locations  
-10 CFR 50 Appendix I 1395.2.1 Noble Gases 1395.2.2 lodines, Tritium and Particulates 1405.3 Gaseous Radioactive System Dose Calculations Once per Month 1425.4 Alternative Gaseous Dose Calculational Methodology 1436.0 TMI-1 GASEOUS EFFLUENT WASTE TREATMENT SYSTEM 1656.1 Description of the TMI-1 Gaseous Radwaste Treatment System 1656.2 Operability of the TMI-1 Gaseous Radwaste Treatment System 1657.0 EFFLUENT TOTAL DOSE ASSESSMENT 1678.0 TMINS RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM (REMP) 1688.1 Monitoring Program Requirements 1688.2 Land Use Census 1718.3 Interlaboratory Comparison Program 1739.0 PART III REFERENCES 191 CY-TM-1 70-300Revision 3Page 8 of 209TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART IIISectionTABLESTable 1.1Table 1.2Table 2.1Table 2.2Table 4.1Table 4.2Table 4.3Table 4.4Table 4.5Table 4.6Table 5.2.1Table 5.2.2Table 5.2.3Table 5.2.4Table 5.3.1Table 5.4.1Table 5.4.2Table 5.4.3Table 5.4.4Table 5.5.1PaqeTMI Liquid Release Point and Liquid Radiation Monitor DataTMI-2 Sump Capacities Liquid Dose Conversion Factors (DCF): DFijBioaccumulation
: Factors, BFiTMI-1 Gaseous Release Point and Gaseous Radiation Monitor DataTMI-2 Gaseous Release Point and Gaseous Radiation Monitor DataDose Factors for Noble Gases and Daughters Atmospheric Dispersion Factors for Three Mile Island -Station VentAtmospheric Dispersion Factors for Three Mile Island -Ground ReleaseDose Parameters for Radioiodines and Radioactive Particulate In GaseousEffluents Pathway Dose Factors, Ri -Infant, Inhalation Pathway Dose Factors, Ri -Child, Inhalation Pathway Dose Factors, Ri -Teen, Inhalation Pathway Dose Factors, Ri -Adult, Inhalation Pathway Dose Factors, Ri -All Age Groups, Ground PlanePathway Dose Factors, Ri -Infant, Grass-Cow-Milk Pathway Dose Factors, R -Child, Grass-Cow-Milk Pathway Dose Factors, Ri -Teen, Grass-Cow-Milk Pathway Dose Factors, Ri -Adult, Grass-Cow-Milk Pathway Dose Factors, Ri -Infant, Grass-Goat-Milk 102103109112125126127128129130144145146147148149150151152153 CY-TM-1 70-300Revision 3Page 9 of 209TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART IIISectionTABLESTable 5.5.2Table 5.5.3Table 5.5.4Table 5.6.1Table 5.6.2Table 5.6.3Table 5.6.4Table 5.7.1Table 5.7.2Table 5.7.3Table 5.7.4Table 8.1Table 8.2Table 8.3Table 8.4Table 8.5Table 8.6Table 8.7Table 8.8Table 8.9Table 8.10PaaqePathway Dose Factors, Ri -Child, Grass-Goat-Milk Pathway Dose Factors, Ri -Teen, Grass-Goat-Milk Pathway Dose Factors, Ri -Adult, Grass-Goat-Milk Pathway Dose Factors, Ri -Infant, Grass-Cow-Meat Pathway Dose Factors, Ri -Child, Grass-Cow-Meat Pathway Dose Factors, Ri -Teen, Grass-Cow-Meat Pathway Dose Factors, Ri -Adult, Grass-Cow-Meat Pathway Dose Factors, Ri -Infant, Vegetation Pathway Dose Factors, R1 -Child, Vegetation Pathway Dose Factors, Ri -Teen, Vegetation Pathway Dose Factors, Ri -Adult, Vegetation Sample Collection and Analysis Requirements Reporting Levels for Radioactivity Concentrations in Environmental SamplesDetection Capabilities for Environmental Sample AnalysisTMINS REMP Station Locations  
-Air Particulate and Air IodineTMINS REMP Station Locations  
-Direct Radiation TMINS REMP Station Locations  
-Direct Radiation TMINS REMP Station Locations  
-Surface WaterTMINS REMP Station Locations  
-Surface Water TMINS REMP Station Locations  
-Aquatic SedimentTMINS REMP Station Locations  
-Aquatic Sediment TMINS REMP Station Locations  
-MilkTMINS REMP Station Locations  
-Milk TMINS REMP Station Locations  
-FishTMINS REMP Station Locations  
-Fish TMINS REMP Station Locations  
-Food Products154155156157158159160161162163164174180181184184186186187187187 CY-TM-1 70-300Revision 3Page 10 of 209TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART IIISectionMAPSPaqeMAP 8.1 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations within 1 Mile of the SiteMAP 8.2 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations within 5 miles of the SiteMAP 8.3 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Greater than 5 miles from the Site188189190FIGURESFigure 1.1Figure 1.2Figure 3.1Figure 3.2Figure 4.1Figure 4.2Figure 4.3Figure 4.4Figure 4.5Figure 6.1TMI-1 Liquid Effluent PathwaysTMI-2 Liquid Effluent PathwaysTMI-1 Liquid RadwasteTMI-1 Liquid Waste Evaporators TMI-1 Gaseous Effluent PathwaysTMI-1 Auxiliary and Fuel Handling Buildings Effluent PathwaysTMI-1 Reactor Building Effluent PathwayTMI-1 Condenser Offgas Effluent PathwayTMI-2 Gaseous Effluent Filtration System/Pathways Waste Gas System104105115116131132.133134135166 CY-TM-1 70-300Revision 3Page 11 of 209TABLE OF CONTENTS (Cont'd)PART IV REPORTING REQUIREMENTS Section Page1.0 TMI ANNUAL RADIOLOGICAL ENVIRONMENTAL OPERATING REPORT 1942.0 TMI ANNUAL RADIOACTIVE EFFLUENT RELEASE REPORT 1953.0 PART IV REFERENCES 197APPENDICES A. Pathway Dose Rate Parameter (Pi) 198B. Inhalation Pathway Dose Factor (Ri) 199C. Ground Plane Pathway Dose Factor (Ri) 200D. Grass-Cow-Milk Pathway Dose Factor (R1) 201E. Cow-Meat Pathway Dose Factor .(Ri) 203F. Vegetation Pathway Dose Factor (Ri) 205APPENDIX A -F REFERENCES 206 CY-TM-1 70-300Revision 3Page 12 of 209PART ITMI-1 RADIOLOGICAL EFFLUENT CONTROLS CY-TM-170-300 Revision 3Page 13 of 2091.0 DEFINITIONS The following terms are defined for uniform interpretation of these controls andsurveillances.
-Food Products 154 155 156 157 158 159 160 161 162 163 164 174 180 181 184 184 186 186 187 187 187 CY-TM-1 70-300 Revision 3 Page 10 of 209 TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART III Section MAPS Paqe MAP 8.1 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations within 1 Mile of the Site MAP 8.2 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations within 5 miles of the Site MAP 8.3 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Greater than 5 miles from the Site 188 189 190 FIGURES Figure 1.1 Figure 1.2 Figure 3.1 Figure 3.2 Figure 4.1 Figure 4.2 Figure 4.3 Figure 4.4 Figure 4.5 Figure 6.1 TMI-1 Liquid Effluent Pathways TMI-2 Liquid Effluent Pathways TMI-1 Liquid Radwaste TMI-1 Liquid Waste Evaporators TMI-1 Gaseous Effluent Pathways TMI-1 Auxiliary and Fuel Handling Buildings Effluent Pathways TMI-1 Reactor Building Effluent Pathway TMI-1 Condenser Offgas Effluent Pathway TMI-2 Gaseous Effluent Filtration System/Pathways Waste Gas System 104 105 115 116 131 132.133 134 135 166 CY-TM-1 70-300 Revision 3 Page 11 of 209 TABLE OF CONTENTS (Cont'd)PART IV REPORTING REQUIREMENTS Section Page 1.0 TMI ANNUAL RADIOLOGICAL ENVIRONMENTAL OPERATING REPORT 194 2.0 TMI ANNUAL RADIOACTIVE EFFLUENT RELEASE REPORT 195 3.0 PART IV REFERENCES 197 APPENDICES A. Pathway Dose Rate Parameter (Pi) 198 B. Inhalation Pathway Dose Factor (Ri) 199 C. Ground Plane Pathway Dose Factor (Ri) 200 D. Grass-Cow-Milk Pathway Dose Factor (R 1) 201 E. Cow-Meat Pathway Dose Factor .(Ri) 203 F. Vegetation Pathway Dose Factor (Ri) 205 APPENDIX A -F REFERENCES 206 CY-TM-1 70-300 Revision 3 Page 12 of 209 PART I TMI-1 RADIOLOGICAL EFFLUENT CONTROLS CY-TM-170-300 Revision 3 Page 13 of 209 1.0 DEFINITIONS The following terms are defined for uniform interpretation of these controls and surveillances.
1.1 Reactor Operating Conditions 1.1.1 Cold ShutdownThe reactor is in the cold shutdown condition when it is subcritical by atleast one percent delta k/k and Tavg is no more than 2000F. Pressure isdefined by Technical Specification 3.1.2.1.1.2 Hot ShutdownThe reactor is in the hot shutdown condition when it is subcritical by atleast one percent delta k/k and Tavg is at or greater than 5250F.1.1.3 Reactor CriticalThe reactor is critical when the neutron chain reaction is self-sustaining and Keff = 1.0.1.1.4 Hot StandbyThe reactor is in the hot standby condition when all of the following conditions exist:a. Tavg is greater than 5250Fb. The reactor is criticalc. Indicated neutron power on the power range channels is lessthan two percent of rated power. Rated power is defined inTechnical Specification Definition 1.1.1.1.5 Power Operation The reactor is in a power operating condition when the indicated neutronpower is above two percent of rated power as indicated on the powerrange channels.
1.1 Reactor Operating Conditions 1.1.1 Cold Shutdown The reactor is in the cold shutdown condition when it is subcritical by at least one percent delta k/k and Tavg is no more than 200 0 F. Pressure is defined by Technical Specification 3.1.2.1.1.2 Hot Shutdown The reactor is in the hot shutdown condition when it is subcritical by at least one percent delta k/k and Tavg is at or greater than 525 0 F.1.1.3 Reactor Critical The reactor is critical when the neutron chain reaction is self-sustaining and Keff = 1.0.1.1.4 Hot Standby The reactor is in the hot standby condition when all of the following conditions exist: a. Tavg is greater than 5250F b. The reactor is critical c. Indicated neutron power on the power range channels is less than two percent of rated power. Rated power is defined in Technical Specification Definition 1.1.1.1.5 Power Operation The reactor is in a power operating condition when the indicated neutron power is above two percent of rated power as indicated on the power range channels.
Rated power is defined in Technical Specification Definition 1.1.
Rated power is defined in Technical Specification Definition 1.1.
CY-TM-1 70-300Revision 3Page 14 of 2091.1.6 Refueling ShutdownThe reactor is in the refueling shutdown condition when, even with allrods removed, the reactor would be subcritical by at least one percentdelta k/k and the coolant temperature at the decay heat removal pumpsuction is no more than 1400F. Pressure is defined by Technical Specification 3.1.2. A refueling shutdown refers to a shutdown toreplace or rearrange all or a portion of the fuel assemblies and/or controlrods.1.1.7 Refueling Operation An operation involving a change in core geometry by manipulation offuel or control rods when the reactor vessel head is removed.1.1.8 Refueling IntervalThe time between normal refuelings of the reactor.
CY-TM-1 70-300 Revision 3 Page 14 of 209 1.1.6 Refueling Shutdown The reactor is in the refueling shutdown condition when, even with all rods removed, the reactor would be subcritical by at least one percent delta k/k and the coolant temperature at the decay heat removal pump suction is no more than 140 0 F. Pressure is defined by Technical Specification 3.1.2. A refueling shutdown refers to a shutdown to replace or rearrange all or a portion of the fuel assemblies and/or control rods.1.1.7 Refueling Operation An operation involving a change in core geometry by manipulation of fuel or control rods when the reactor vessel head is removed.1.1.8 Refueling Interval The time between normal refuelings of the reactor. This is defined as once per 24 months.1.1.9 Startup The reactor shall be considered in the startup mode when the shutdown margin is reduced with the intent of going critical.1.1.10 Tave Tave is defined as the arithmetic average of the coolant temperatures in the hot and cold legs of the loop with the greater number of reactor coolant pumps operating, if such a distinction of loops can be made.1.1.11 Heatup -Cooldown Mode The heatup-cooldown mode is the range of reactor coolant temperature greater than 200OF and less than 5250F.1.2 Operable A system, subsystem, train, component or device, shall be OPERABLE or have OPERABILITY when it is capable of performing it's specified function(s), and when all necessary attendant instrumentation, controls, electrical power, cooling or seal water, lubrication or other auxiliary equipment that are required for the system, subsystem, train, component, or device to perform its function(s), are also capable of performing their related support function(s).
This is defined asonce per 24 months.1.1.9 StartupThe reactor shall be considered in the startup mode when the shutdownmargin is reduced with the intent of going critical.
1.3 Instrument Channel An instrument channel is the combination of sensor, wires, amplifiers, and output devices, which are connected for the purpose of measuring the value of a CY-TM-1 70-300 Revision 3 Page 15 of 209 process variable, for the purpose of observation, control, and/or protection.
1.1.10 TaveTave is defined as the arithmetic average of the coolant temperatures inthe hot and cold legs of the loop with the greater number of reactorcoolant pumps operating, if such a distinction of loops can be made.1.1.11 Heatup -Cooldown ModeThe heatup-cooldown mode is the range of reactor coolant temperature greater than 200OF and less than 5250F.1.2 OperableA system, subsystem, train, component or device, shall be OPERABLE or haveOPERABILITY when it is capable of performing it's specified function(s),
An instrument channel may be either analog or digital.1.4 Instrumentation Surveillance 1.4.1 Channel Test A CHANNEL TEST shall be the injection of a simulated signal into the channel as close to the sensor as practical to verify OPERABILITY, including alarm and/or trip functions.
andwhen all necessary attendant instrumentation,  
1.4.2 Channel Check A CHANNEL CHECK shall be the qualitative assessment of channel behavior during operation by observation.
: controls, electrical power, coolingor seal water, lubrication or other auxiliary equipment that are required for thesystem, subsystem, train, component, or device to perform its function(s),
This determination shall include, where possible, comparison of the channel indication and/or status with other indications and/or status derived from independent instrumentation channels measuring the same parameter.
arealso capable of performing their related support function(s).
1.4.3 Source Check A SOURCE CHECK shall be the qualitative assessment of channel response when the channel sensor is exposed to a radioactive source.1.4.4 Channel Calibration An instrument CHANNEL CALIBRATION is a test, and adjustment (if necessary), to establish that the channel output responds with acceptable range and accuracy to known values of the parameter, which the channel measures, or an accurate simulation of these values.Calibration shall encompass the entire channel, including equipment actuation, alarm, or trip and shall be deemed to include the channel test.1.5 Dose Equivalent 1-131 The DOSE EQUIVALENT 1-131 shall be that concentration of 1-131 (microcurie/gram), which alone would produce the same thyroid dose as the quantity and isotopic mixture of 1-131, 1-132, I-133, 1-134, and 1-135 actually present. The thyroid dose conversion factors used for this calculation shall be those listed in Table III of TID 14844, "Calculation of Distance Factors for Power and Test Reactor Sites". [Or in Table E-7 of NRC Regulatory Guide 1.109, Revision 1, October, 1977.]
1.3 Instrument ChannelAn instrument channel is the combination of sensor, wires, amplifiers, and outputdevices, which are connected for the purpose of measuring the value of a CY-TM-1 70-300Revision 3Page 15 of 209process variable, for the purpose of observation,  
CY-TM-170-300 Revision 3 Page 16 of 209 1.6 Offsite Dose Calculation Manual (ODCM)The OFFSITE DOSE CALCULATION MANUAL (ODCM) contains the methodology and parameters used in the calculation of offsite doses resulting from radioactive gaseous and liquid effluent, in the calculation of gaseous and liquid effluent monitoring Alarm/Trip Setpoints,.
: control, and/or protection.
and in the conduct of the Radiological Environmental Monitoring Program. The ODCM also contains (1)the Radiological Effluent Controls, (2) the Radiological Environmental Monitoring Program and (3) descriptions of the information that should be included in the Annual Radiological Environmental Operating and Annual Radioactive Effluent Release Reports.1.7 Gaseous Radwaste Treatment The GASEOUS RADWASTE TREATMENT SYSTEM is the system designed and installed to reduce radioactive gaseous effluent by collecting primary coolant system off gases from the primary system and providing for delay or holdup for the purpose of reducing the total radioactivity prior to release to the environment.
Aninstrument channel may be either analog or digital.1.4 Instrumentation Surveillance 1.4.1 Channel TestA CHANNEL TEST shall be the injection of a simulated signal into thechannel as close to the sensor as practical to verify OPERABILITY, including alarm and/or trip functions.
1.8 Ventilation Exhaust Treatment System A VENTILATION EXHAUST TREATMENT SYSTEM is any system designed and installed to reduce gaseous radioiodine or radioactive material in particulate form in effluent by passing ventilation or vent exhaust gases through charcoal absorbers and/or HEPA filters for the purpose of removing iodine or particulates from the gaseous exhaust system prior to the release to the environment.
1.4.2 Channel CheckA CHANNEL CHECK shall be the qualitative assessment of channelbehavior during operation by observation.
Engineered Safety Feature (ESF) atmospheric cleanup systems are not considered to be VENTILATION EXHAUST TREATMENT SYSTEMS.1.9 Purge -Purging PURGE or PURGING is the controlled process of discharging air or gas from a confinement to maintain temperature, pressure, humidity, concentration or other operating conditions in such a manner that replacement air or gas is required to purify the confinement.
This determination shallinclude, where possible, comparison of the channel indication and/orstatus with other indications and/or status derived from independent instrumentation channels measuring the same parameter.
1.10 Venting VENTING is the controlled process of discharging air as gas from a confinement to maintain temperature, pressure, humidity, concentration or other operating conditions in such a manner that replacement air or gas is not provided.
1.4.3 Source CheckA SOURCE CHECK shall be the qualitative assessment of channelresponse when the channel sensor is exposed to a radioactive source.1.4.4 Channel Calibration An instrument CHANNEL CALIBRATION is a test, and adjustment (ifnecessary),
Vent used in system name does not imply a VENTING process.1.11 Member(s) of the Public MEMBER OF THE PUBLIC means any individual except when that individual is receiving an occupational dose.
to establish that the channel output responds withacceptable range and accuracy to known values of the parameter, whichthe channel measures, or an accurate simulation of these values.Calibration shall encompass the entire channel, including equipment actuation, alarm, or trip and shall be deemed to include the channel test.1.5 Dose Equivalent 1-131The DOSE EQUIVALENT 1-131 shall be that concentration of 1-131(microcurie/gram),
CY-TM-170-300 Revision 3 Page 17 of 209 1.12 Site Boundary The SITE BOUNDARY used as the basis for the limits on the release of gaseous effluents is as defined in Section 2.1.2.2 and shown on Figure 2.1-3 of the TMI-1 FSAR. This boundary line includes portions of the Susquehanna River surface between the east bank of the river and Three Mile Island and between Three Mile Island and Shelley Island.The SITE BOUNDARY used as the basis for the limits on the release of liquid effluents is as shown in Figure 1.1 in Part I of this ODCM.1.13 Frequency Notation The FREQUENCY NOTATION specified for the performance of Surveillance Requirements shall correspond to the intervals defined in Table 1-1. All Surveillance Requirements shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% of the surveillance interval.
which alone would produce the same thyroid dose as thequantity and isotopic mixture of 1-131, 1-132, I-133, 1-134, and 1-135 actuallypresent.
The 25% extension applies to all frequency intervals with the exception of "F." No extension is allowed for intervals designated "F." 1.14 Occupational Dose OCCUPATIONAL DOSE means the dose received by an individual in the course of employment in which the individual's assigned duties involve exposure to radiation or to radioactive material from licensed and unlicensed sources of radiation, whether in the possession of the licensee or other person.Occupational dose does not include doses received from background radiation, from any medical administration the individual has received; from exposure to individuals administered radioactive material and released under 10CFR35.75, from voluntary participation in medical research programs, or as a member of the public.
The thyroid dose conversion factors used for this calculation shall bethose listed in Table III of TID 14844, "Calculation of Distance Factors for Powerand Test Reactor Sites". [Or in Table E-7 of NRC Regulatory Guide 1.109,Revision 1, October, 1977.]
CY-TM-1 70-300 Revision 3 Page 18 of 209 Table 1-1 Frequency Notation Notation Frequency S Shiftly (once per 12 hours)D Daily (once per 24 hours)W Weekly (once per 7 days)M Monthly (once per 31 days)Q Quarterly (once per 92 days)S/A Semi-Annually (once per 184 days)R Refueling Interval (once per 24 months)P S/U Prior to each reactor startup, if not done during the previous 7 days P Completed prior to each release N/A (NA) Not applicable E Once per 18 months F Not to exceed 24 months Bases Section 1.13 establishes the limit for which the specified time interval for Surveillance Requirements may be extended.
CY-TM-170-300 Revision 3Page 16 of 2091.6 Offsite Dose Calculation Manual (ODCM)The OFFSITE DOSE CALCULATION MANUAL (ODCM) contains themethodology and parameters used in the calculation of offsite doses resulting from radioactive gaseous and liquid effluent, in the calculation of gaseous andliquid effluent monitoring Alarm/Trip Setpoints,.
It permits an allowable extension of the normal surveillance interval to facilitate surveillance scheduling and consideration of plant operating conditions that may not be suitable for conducting the surveillance; e.g., transient conditions or other ongoing surveillance or maintenance activities.
and in the conduct of theRadiological Environmental Monitoring Program.
It also provides flexibility to accommodate the length of a fuel cycle for surveillances that are specified to be performed at least once each REFUELING INTERVAL.
The ODCM also contains (1)the Radiological Effluent  
It is not intended that this provision be used repeatedly as a convenience to extend surveillance intervals beyond that specified for surveillances that are not performed once each REFUELING INTERVAL.
: Controls, (2) the Radiological Environmental Monitoring Program and (3) descriptions of the information that should be included in theAnnual Radiological Environmental Operating and Annual Radioactive EffluentRelease Reports.1.7 Gaseous Radwaste Treatment The GASEOUS RADWASTE TREATMENT SYSTEM is the system designedand installed to reduce radioactive gaseous effluent by collecting primary coolantsystem off gases from the primary system and providing for delay or holdup forthe purpose of reducing the total radioactivity prior to release to the environment.
Likewise, it is not the intent that REFUELING INTERVAL surveillances be performed during power operation unless it is consistent with safe plant operation.
1.8 Ventilation Exhaust Treatment SystemA VENTILATION EXHAUST TREATMENT SYSTEM is any system designed andinstalled to reduce gaseous radioiodine or radioactive material in particulate formin effluent by passing ventilation or vent exhaust gases through charcoalabsorbers and/or HEPA filters for the purpose of removing iodine or particulates from the gaseous exhaust system prior to the release to the environment.
Engineered Safety Feature (ESF) atmospheric cleanup systems are notconsidered to be VENTILATION EXHAUST TREATMENT SYSTEMS.1.9 Purge -PurgingPURGE or PURGING is the controlled process of discharging air or gas from aconfinement to maintain temperature,  
: pressure, humidity, concentration or otheroperating conditions in such a manner that replacement air or gas is required topurify the confinement.
1.10 VentingVENTING is the controlled process of discharging air as gas from a confinement to maintain temperature,  
: pressure, humidity, concentration or other operating conditions in such a manner that replacement air or gas is not provided.
Ventused in system name does not imply a VENTING process.1.11 Member(s) of the PublicMEMBER OF THE PUBLIC means any individual except when that individual isreceiving an occupational dose.
CY-TM-170-300 Revision 3Page 17 of 2091.12 Site BoundaryThe SITE BOUNDARY used as the basis for the limits on the release of gaseouseffluents is as defined in Section 2.1.2.2 and shown on Figure 2.1-3 of the TMI-1FSAR. This boundary line includes portions of the Susquehanna River surfacebetween the east bank of the river and Three Mile Island and between Three MileIsland and Shelley Island.The SITE BOUNDARY used as the basis for the limits on the release of liquideffluents is as shown in Figure 1.1 in Part I of this ODCM.1.13 Frequency NotationThe FREQUENCY NOTATION specified for the performance of Surveillance Requirements shall correspond to the intervals defined in Table 1-1. AllSurveillance Requirements shall be performed within the specified time intervalwith a maximum allowable extension not to exceed 25% of the surveillance interval.
The 25% extension applies to all frequency intervals with the exception of "F." No extension is allowed for intervals designated "F."1.14 Occupational DoseOCCUPATIONAL DOSE means the dose received by an individual in the courseof employment in which the individual's assigned duties involve exposure toradiation or to radioactive material from licensed and unlicensed sources ofradiation, whether in the possession of the licensee or other person.Occupational dose does not include doses received from background radiation, from any medical administration the individual has received; from exposure toindividuals administered radioactive material and released under 10CFR35.75, from voluntary participation in medical research  
: programs, or as a member of thepublic.
CY-TM-1 70-300Revision 3Page 18 of 209Table 1-1Frequency NotationNotation Frequency S Shiftly (once per 12 hours)D Daily (once per 24 hours)W Weekly (once per 7 days)M Monthly (once per 31 days)Q Quarterly (once per 92 days)S/A Semi-Annually (once per 184 days)R Refueling Interval (once per 24 months)P S/U Prior to each reactor startup, if not doneduring the previous 7 daysP Completed prior to each releaseN/A (NA) Not applicable E Once per 18 monthsF Not to exceed 24 monthsBasesSection 1.13 establishes the limit for which the specified time interval for Surveillance Requirements may be extended.
It permits an allowable extension of the normal surveillance interval to facilitate surveillance scheduling and consideration of plant operating conditions thatmay not be suitable for conducting the surveillance; e.g., transient conditions or other ongoingsurveillance or maintenance activities.
It also provides flexibility to accommodate the length ofa fuel cycle for surveillances that are specified to be performed at least once eachREFUELING INTERVAL.
It is not intended that this provision be used repeatedly as aconvenience to extend surveillance intervals beyond that specified for surveillances that arenot performed once each REFUELING INTERVAL.  
: Likewise, it is not the intent thatREFUELING INTERVAL surveillances be performed during power operation unless it isconsistent with safe plant operation.
The limitation of Section 1.13 is based on engineering judgment and the recognition that the most probable result of any particular surveillance being performed is the verification of conformance with the Surveillance Requirements.
The limitation of Section 1.13 is based on engineering judgment and the recognition that the most probable result of any particular surveillance being performed is the verification of conformance with the Surveillance Requirements.
Thisprovision is sufficient to ensure that the reliability ensured through surveillance activities is notsignificantly degraded beyond that obtained from the specified surveillance interval.
This provision is sufficient to ensure that the reliability ensured through surveillance activities is not significantly degraded beyond that obtained from the specified surveillance interval.
CY-TM-1 70-300Revision 3Page 19 of 209Map 1.1Gaseous Effluent Release Points and Liquid Effluent Outfall Locations CY-TM-1 70-300Revision 3Page 20 of 2092.0 RADIOLOGICAL EFFLUENT CONTROLS AND BASES2.1 Radioactive Effluent Instrumentation 2.1.1 Radioactive Liquid Effluent Instrumentation CONTROL:The radioactive liquid effluent monitoring instrumentation channelsshown in Table 2.1-1 shall be OPERABLE with their alarm/trip setpoints set to ensure that the limits of Control 2.2.1.1 are not exceeded.
CY-TM-1 70-300 Revision 3 Page 19 of 209 Map 1.1 Gaseous Effluent Release Points and Liquid Effluent Outfall Locations CY-TM-1 70-300 Revision 3 Page 20 of 209 2.0 RADIOLOGICAL EFFLUENT CONTROLS AND BASES 2.1 Radioactive Effluent Instrumentation 2.1.1 Radioactive Liquid Effluent Instrumentation CONTROL: The radioactive liquid effluent monitoring instrumentation channels shown in Table 2.1-1 shall be OPERABLE with their alarm/trip setpoints set to ensure that the limits of Control 2.2.1.1 are not exceeded.
Thealarm/trip setpoints of these channels shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:
The alarm/trip setpoints of these channels shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:
At all times *ACTION:a. With a radioactive liquid effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required bythe above control, immediately suspend the release ofradioactive liquid effluent monitored by the affected channel ordeclare the channel inoperable.
At all times *ACTION: a. With a radioactive liquid effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required by the above control, immediately suspend the release of radioactive liquid effluent monitored by the affected channel or declare the channel inoperable.
: b. With less than the minimum number of radioactive liquideffluent monitoring instrumentation channels  
: b. With less than the minimum number of radioactive liquid effluent monitoring instrumentation channels OPERABLE, take the ACTION shown in Table 2.1 -1. Exert best efforts to return the instrumentation to OPERABLE status within 30 days and, if unsuccessful, explain in the next Annual Effluent Release Report why the inoperability was not corrected in a timely manner.For WDL-FT-84, and RM-L-6, operability is not required when discharges are positively controlled through the closure of WDL-V-257.
: OPERABLE, take the ACTION shown in Table 2.1 -1. Exert best efforts toreturn the instrumentation to OPERABLE status within 30days and, if unsuccessful, explain in the next Annual EffluentRelease Report why the inoperability was not corrected in atimely manner.For WDL-FT-84, and RM-L-6, operability is notrequired when discharges are positively controlled through the closure of WDL-V-257.
For RM-L-12 and associated IWTS/IWFS flow interlocks, operability is not required when discharges are positively controlled through the closure of IW-V-72, 75 and IW-V-280, 281.For SR-FT-146, operability is not required when discharges are positively controlled through the closure of WDL-V-257, IW-V-72, 75 and IW-V-280, 281.
For RM-L-12 and associated IWTS/IWFS flowinterlocks, operability is not required whendischarges are positively controlled through theclosure of IW-V-72, 75 and IW-V-280, 281.For SR-FT-146, operability is not required whendischarges are positively controlled through theclosure of WDL-V-257, IW-V-72, 75 and IW-V-280, 281.
CY-TM-1 70-300 Revision 3 Page 21 of 209 BASES The radioactive liquid effluent instrumentation is provided to monitor and control, as applicable, the releases of radioactive materials in liquid effluent during actual or potential releases.
CY-TM-1 70-300Revision 3Page 21 of 209BASESThe radioactive liquid effluent instrumentation is provided to monitor andcontrol, as applicable, the releases of radioactive materials in liquideffluent during actual or potential releases.
The alarm/trip setpoints for these instruments shall be calculated in accordance with NRC approved methods in the ODCM to ensure that the alarm/trip will occur prior to exceeding ten times the effluent concentrations of 10 CFR Part 20.
The alarm/trip setpoints forthese instruments shall be calculated in accordance with NRC approvedmethods in the ODCM to ensure that the alarm/trip will occur prior toexceeding ten times the effluent concentrations of 10 CFR Part 20.
CY-TM-170-300 Revision 3 Page 22 of 209 Table 2.1-1 Radioactive Liquid Effluent Instrumentation Minimum Channels Operable Instrument ACTION 1. Gross Radioactivity Monitors Providing Automatic Termination of Release a. Unit 1 Liquid Radwaste Effluent Line (RM-L6)b. IWTS/IWFS Discharge Line (RM-L12)2. Flow Rate Measurement Devices a. Unit 1 Liquid Radwaste Effluent Line (WDL-FT-84)
CY-TM-170-300 Revision 3Page 22 of 209Table 2.1-1Radioactive Liquid Effluent Instrumentation MinimumChannelsOperableInstrument ACTION1. Gross Radioactivity MonitorsProviding Automatic Termination of Releasea. Unit 1 Liquid Radwaste Effluent Line (RM-L6)b. IWTS/IWFS Discharge Line (RM-L12)2. Flow Rate Measurement Devicesa. Unit 1 Liquid Radwaste Effluent Line (WDL-FT-84)
: b. Station Effluent Discharge (SR-FT-146) 1 1 18 20 1 1 21 21 Table Notation ACTION 18 With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases may continue, provided that prior to initiating a release: 1. At least two independent samples are analyzed in accordance with Surveillances 3.2.1.1.1 and 3.2.1.1.2 and;2. At least two technically qualified members of the Unit staff independently verify the release rate calculations and verify the discharge valve lineup.3. The TMI Plant Manager shall approve each release. Otherwise, suspend release of radioactive effluents via this pathway.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may commence or continue provided that grab samples are collected and analyzed for gross radioactivity (beta or gamma) at a limit of detection of at least lx10-7 microcuries/ml, prior to initiating a release and at least once per 12 hours during release.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, radioactive effluent releases via this pathway may continue, provided the flow rate is estimated at least once per 4 hours during actual releases.
: b. Station Effluent Discharge (SR-FT-146) 111820112121Table NotationACTION 18With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, effluent releases may continue, provided thatprior to initiating a release:1. At least two independent samples are analyzed in accordance withSurveillances 3.2.1.1.1 and 3.2.1.1.2 and;2. At least two technically qualified members of the Unit staff independently verify the release rate calculations and verify the discharge valve lineup.3. The TMI Plant Manager shall approve each release.
Pump curves may be used to estimate flow.ACTION 20 ACTION 21 CY-TM-1 70-300 Revision 3 Page 23 of 209 2.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation CONTROL: The radioactive gaseous process and effluent monitoring instrumentation channels shown in Table 2.1-2 shall be OPERABLE with their alarm/trip setpoints set to ensure that the limits of Control 2.2.2.1 are not exceeded.
Otherwise, suspend release of radioactive effluents via this pathway.With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, effluent releases via this pathway maycommence or continue provided that grab samples are collected and analyzedfor gross radioactivity (beta or gamma) at a limit of detection of at least lx10-7microcuries/ml, prior to initiating a release and at least once per 12 hours duringrelease.With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, radioactive effluent releases via this pathwaymay continue, provided the flow rate is estimated at least once per 4 hoursduring actual releases.
The alarm/trip setpoints of these channels shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:
Pump curves may be used to estimate flow.ACTION 20ACTION 21 CY-TM-1 70-300Revision 3Page 23 of 2092.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation CONTROL:The radioactive gaseous process and effluent monitoring instrumentation channels shown in Table 2.1-2 shall be OPERABLE withtheir alarm/trip setpoints set to ensure that the limits of Control 2.2.2.1are not exceeded.
As shown in Table 2.1-2 ACTION: a. With a radioactive gaseous process or effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required by the above control, immediately suspend the release of radioactive effluent monitored by the affected channel or declare the channel inoperable.
The alarm/trip setpoints of these channels shall bedetermined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:
: b. With less than the minimum number of radioactive gaseous process or effluent monitoring instrumentation channels OPERABLE, take the ACTION shown in Table 2.1-2. Exert best efforts to return the instrumentation to OPERABLE status within 30 days and, if unsuccessful, explain in the next Annual Effluent Release Report why the inoperability was not corrected in a timely manner.BASES The radioactive gaseous effluent instrumentation is provided to monitor and control, as applicable, the releases of radioactive materials in gaseous effluent during actual or potential releases.
As shown in Table 2.1-2ACTION:a. With a radioactive gaseous process or effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required by the above control, immediately suspend therelease of radioactive effluent monitored by the affectedchannel or declare the channel inoperable.
The alarm/trip setpoints for these instruments shall be calculated in accordance with NRC approved methods in the ODCM to provide reasonable assurance that the annual releases are within the limits specified in 10 CFR 20.1301.The low range condenser offgas noble gas activity monitors also provide data for determination of steam generator primary to secondary leakage rate. Channel operability requirements are based on an AmerGen letter#5928-06-20449, "Request to Revise Condenser Vent System Low Range Noble Gas Monitor Operability Requirements", Pamela B. Cowan to U.S.N.R.C., May 25, 2006.
: b. With less than the minimum number of radioactive gaseousprocess or effluent monitoring instrumentation channelsOPERABLE, take the ACTION shown in Table 2.1-2. Exertbest efforts to return the instrumentation to OPERABLE statuswithin 30 days and, if unsuccessful, explain in the next AnnualEffluent Release Report why the inoperability was notcorrected in a timely manner.BASESThe radioactive gaseous effluent instrumentation is provided to monitorand control, as applicable, the releases of radioactive materials ingaseous effluent during actual or potential releases.
CY-TM-1 70-300 Revision 3 Page 24 of 209 Table 2.1-2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUM CHANNEL INSTRUMENT OPERABLE APPLICABILITY ACTION 1. Waste Gas Holdup System a. Noble Gas Activity Monitor (RM-A-7) 1 25 B. Effluent System Flow Rate Measuring Device (WDG-FT-123) 1 261 2. Waste Gas Holdup System Explosive Gas Monitoring System a. Hydrogen Monitor (CA-G-1A/B) 2 ** 30 b. Oxygen Monitor (CA-G-1A/B) 2 ** 30 3. Containment Purge Monitoring System a. Noble Gas Activity Monitor (RM-A-9) 1 # 27 b. Iodine Sampler (RM-A-9) 1 # 31 c. Particulate Sampler (RM-A-9) 1 # 31 d. Effluent System Flow Rate Measuring Device (AH-FR-148A, AH-FR-148B) 1 # 26 e. Sampler Flow Rate Monitor (RM-FI-1231) 1 # 26 4. Condenser Vent System a. Low Range Noble Gas Activity Monitor (RM-A-5Lo or RM-A-15) 1## 32 CY-TM-1 70-300 Revision 3 Page 25 of 209 Table 2.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUM CHANNEL INSTRUMENT OPERABLE APPLICABILITY ACTION 5. Auxiliary and Fuel Handling Building Ventilation System a. Noble Gas Activity Monitor (RM-A-8) or (RM-A-4 and RM-A-6) 1
The alarm/trip setpoints for these instruments shall be calculated in accordance withNRC approved methods in the ODCM to provide reasonable assurance that the annual releases are within the limits specified in 10 CFR20.1301.The low range condenser offgas noble gas activity monitors also providedata for determination of steam generator primary to secondary leakagerate. Channel operability requirements are based on an AmerGen letter#5928-06-20449, "Request to Revise Condenser Vent System LowRange Noble Gas Monitor Operability Requirements",
* 27 b. Iodine Sampler (RM-A-8 or (RM-A-4 and RM-A-6) 1
Pamela B. Cowanto U.S.N.R.C.,
* 31 c. Particulate Sampler (RM-A-8 or (RM-A-4 and RM-A-6) 1
May 25, 2006.
* 31 d. Effluent System Flow Rate Measuring Devices (AH-FR-149 and 1
CY-TM-1 70-300Revision 3Page 24 of 209Table 2.1-2Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUMCHANNELINSTRUMENT OPERABLE APPLICABILITY ACTION1. Waste Gas Holdup Systema. Noble Gas Activity Monitor (RM-A-7) 1 25B. Effluent System Flow Rate Measuring Device (WDG-FT-123) 1 2612. Waste Gas Holdup System Explosive Gas Monitoring Systema. Hydrogen Monitor (CA-G-1A/B) 2 ** 30b. Oxygen Monitor (CA-G-1A/B) 2 ** 303. Containment Purge Monitoring Systema. Noble Gas Activity Monitor (RM-A-9) 1 # 27b. Iodine Sampler (RM-A-9) 1 # 31c. Particulate Sampler (RM-A-9) 1 # 31d. Effluent System Flow Rate Measuring Device (AH-FR-148A, AH-FR-148B) 1 # 26e. Sampler Flow Rate Monitor (RM-FI-1231) 1 # 264. Condenser Vent Systema. Low Range Noble Gas Activity Monitor (RM-A-5Lo or RM-A-15) 1## 32 CY-TM-1 70-300Revision 3Page 25 of 209Table 2.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUMCHANNELINSTRUMENT OPERABLE APPLICABILITY ACTION5. Auxiliary and Fuel Handling Building Ventilation Systema. Noble Gas Activity Monitor (RM-A-8) or (RM-A-4 and RM-A-6) 1
* 26 AH-FR-1 50)e. Sampler Flow Rate Monitor (RM-FI-1230 or RM-A-4\FI and RM-A-6\FI) 1 26 6. Fuel Handling Building ESF Air Treatment System a. Noble Gas Activity Monitor (RM-A-14 or suitable equivalent) 1 .... 27,33 b. Iodine Cartridge N/A(2) .... 31,33 c. Particulate Filter N/A(2) .... 31,33 d. Effluent System Flow (AH-UR-1 104A/B) 1 .... 26,33 e. Sampler Flow Rate Monitor (RM-A-14FI14) 1 26,33 NOTE 2: No instrumentation channel is provided.
* 27b. Iodine Sampler (RM-A-8 or (RM-A-4 and RM-A-6) 1
However, for determining operability, the equipment named must be installed and functional or the ACTION applies.
* 31c. Particulate Sampler (RM-A-8 or (RM-A-4 and RM-A-6) 1
CY-TM-1 70-300 Revision 3 Page 26 of 209 Table 2.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUM CHANNEL INSTRUMENT OPERABLE APPLICABILITY ACTION 7. Chemical Cleaning Building Ventilation System a. Noble Gas Activity Monitor (ALC RM-1-18) 1(3) 27 b. Iodine Sampler (ALC RM-1-18) 1(3) 31 c. Particulate Sampler (ALC RM-1-18) 1 31 8. Waste Handling and Packaging Facility Ventilation System a. Particulate Sampler (WHP-RIT-1) 1 31 9. Respirator and Laundry Maintenance Facility Ventilation System a. Particulate Sampler (RLM-RM-1) 1 31 NOTE 3: Channel only required when liquid radwaste is moved or processed within the facility.
* 31d. Effluent System Flow Rate Measuring Devices (AH-FR-149 and 1
CY-TM-1 70-300 Revision 3 Page 27 of 209 Table 2.1-2 (Cont'd)Table Notation-* At all times-** During waste gas holdup system operation-**
* 26AH-FR-1 50)e. Sampler Flow Rate Monitor (RM-FI-1230 or RM-A-4\FI and RM-A-6\FI) 1 266. Fuel Handling Building ESF Air Treatment Systema. Noble Gas Activity Monitor (RM-A-14 or suitable equivalent) 1 .... 27,33b. Iodine Cartridge N/A(2) .... 31,33c. Particulate Filter N/A(2) .... 31,33d. Effluent System Flow (AH-UR-1 104A/B) 1 .... 26,33e. Sampler Flow Rate Monitor (RM-A-14FI14) 1 26,33NOTE 2: No instrumentation channel is provided.  
* Operability is not required when discharges are positively controlled through the closure of WDG-V-47 or where RM-A-8, AH-FT-149 and AH-FT-150 are operable and RM-A-8 is capable of automatic closure of WDG-V-47 During Fuel Handling Building ESF Air Treatment System Operation-# At all times during containment purging-# At all times when condenser vacuum is established
: However, for determining operability, the equipment named must beinstalled and functional or the ACTION applies.
-### During operation of the ventilation system ACTION 25 With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, the contents of the tank may be released to the environment provided that prior to initiating the release: 1. At least two independent samples of the tank's contents are analyzed in accordance with Table 3.2-2, Item A, and 2. At least two technically qualified members of the Unit staff independently verify the release rate calculations and verify the discharge valve lineup.3. The TMI Plant Manager shall approve each release. Otherwise, suspend release of radioactive effluent via this pathway.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may continue provided the flow rate is estimated at least once per 4 hours.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may continue provided grab samples are taken at least once per 12 hours and the initial samples are analyzed for gross activity (gamma scan) within 24 hours after the channel has been declared inoperable.
CY-TM-1 70-300Revision 3Page 26 of 209Table 2.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUMCHANNELINSTRUMENT OPERABLE APPLICABILITY ACTION7. Chemical Cleaning Building Ventilation Systema. Noble Gas Activity Monitor (ALC RM-1-18) 1(3) 27b. Iodine Sampler (ALC RM-1-18) 1(3) 31c. Particulate Sampler (ALC RM-1-18) 1 318. Waste Handling and Packaging Facility Ventilation Systema. Particulate Sampler (WHP-RIT-1) 1 319. Respirator and Laundry Maintenance Facility Ventilation Systema. Particulate Sampler (RLM-RM-1) 1 31NOTE 3: Channel only required when liquid radwaste is moved or processed within the facility.
If RM-A-9 is declared inoperable, see also Technical Specification 3.5.1, Table 3-5.1, Item C.3.f.ACTION 26 ACTION 27 CY-TM-1 70-300 Revision 3 Page 28 of 209 Table 2.1-2 Notations (Cont'd)ACTION 30 1.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, a grab sample shall be collected and analyzed for the inoperable gas channel(s) at least once per 24 hours. With both channels inoperable, a grab sample shall be collected and analyzed for the inoperable gas channel(s):
CY-TM-1 70-300Revision 3Page 27 of 209Table 2.1-2 (Cont'd)Table Notation-* At all times-** During waste gas holdup system operation
ACTION 31 ACTION 32 (a) at least once per 4 hours during degassing operations.(b) at least once per 24 hours during other operations (e.g. Feed and Bleed).2. If the inoperable gas channel(s) is not restored to service within 14 days, a special report shall be submitted to the Regional Administrator of the NRC Region I Office and a copy to the Director, Office of Inspection and Enforcement within 30 days of declaring the channel(s) inoperable.
-**
The report shall describe (a) the cause of the monitor inoperability, (b) action being taken to restore the instrument to service, and (c) action to be taken to prevent recurrence.
* Operability is not required when discharges are positively controlled through the closure of WDG-V-47 or whereRM-A-8, AH-FT-149 and AH-FT-150 are operable andRM-A-8 is capable of automatic closure of WDG-V-47During Fuel Handling Building ESF Air Treatment SystemOperation
With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may continue provided that within four hours after the channel has been declared inoperable, samples are continuously collected with auxiliary sampling equipment.
-# At all times during containment purging-# At all times when condenser vacuum is established
With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may continue for up to 14 days, provided that grab samples are taken and analyzed.If the primary-to-secondary leak rate was unstable*, or was indicating an increasing trend at the initial time when there was no operable channel of the Condenser Vent System Low Range Noble Gas Activity Monitor, analyze grab samples of the reactor coolant system and Condenser OffGas once every 4 hours to provide an indication of primary-to-secondary leakage. Subsequent sample frequency shall be in accordance with Table 1 based on the last sample result. Otherwise, analyze grab samples of the reactor coolant system and Condenser OffGas to provide an indication of primary-to-secondary leakage at the minimum frequency indicated in Table 1, below:
-### During operation of the ventilation systemACTION 25With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, the contents of the tank may be released tothe environment provided that prior to initiating the release:1. At least two independent samples of the tank's contents are analyzed inaccordance with Table 3.2-2, Item A, and2. At least two technically qualified members of the Unit staff independently verify the release rate calculations and verify the discharge valve lineup.3. The TMI Plant Manager shall approve each release.
CY-TM-170-300 Revision 3 Page 29 of 209 Table 2.1-2 Notations (Cont'd)Table 1 Minimum Frequency of Grab Samples When No Condenser Vent System Low Range Noble Gas Activity Monitor is Operable Existing Total Primary-to-Secondary Leak Rate Frequency of Grab Samples (based on last monitor reading or sample result)0 to < 5 GPD Once per 24 hours 5 to < 30 GPD Once per 12 hours 30 to < 75 GPD Once per 4 hours 75 GPD or greater Place the unit in at least HOT STANDBY within the next 6 hours, and at least HOT SHUTDOWN within the following 6 hours, and at least COLD SHUTDOWN within the subsequent 24 hours.*Unstable is defined as > 10% increase during a 1 hour period, as stated in the EPRI Guidelines.
Otherwise, suspend release of radioactive effluent via this pathway.With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, effluent releases via this pathway maycontinue provided the flow rate is estimated at least once per 4 hours.With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, effluent releases via this pathway maycontinue provided grab samples are taken at least once per 12 hours and theinitial samples are analyzed for gross activity (gamma scan) within 24 hours afterthe channel has been declared inoperable.
If RM-A-9 is declared inoperable, seealso Technical Specification 3.5.1, Table 3-5.1, Item C.3.f.ACTION 26ACTION 27 CY-TM-1 70-300Revision 3Page 28 of 209Table 2.1-2Notations (Cont'd)ACTION 30 1.With the number of channels OPERABLE less than required by theMinimum Channels OPERABLE requirement, a grab sample shall becollected and analyzed for the inoperable gas channel(s) at least onceper 24 hours. With both channels inoperable, a grab sample shall becollected and analyzed for the inoperable gas channel(s):
ACTION 31ACTION 32(a) at least once per 4 hours during degassing operations.
(b) at least once per 24 hours during other operations (e.g. Feedand Bleed).2. If the inoperable gas channel(s) is not restored to service within 14 days,a special report shall be submitted to the Regional Administrator of theNRC Region I Office and a copy to the Director, Office of Inspection andEnforcement within 30 days of declaring the channel(s) inoperable.
Thereport shall describe (a) the cause of the monitor inoperability, (b) actionbeing taken to restore the instrument to service, and (c) action to betaken to prevent recurrence.
With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, effluent releases via this pathway maycontinue provided that within four hours after the channel has been declaredinoperable, samples are continuously collected with auxiliary samplingequipment.
With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, effluent releases via this pathway maycontinue for up to 14 days, provided that grab samples are taken and analyzed.
If the primary-to-secondary leak rate was unstable*,
or was indicating anincreasing trend at the initial time when there was no operable channel of theCondenser Vent System Low Range Noble Gas Activity  
: Monitor, analyze grabsamples of the reactor coolant system and Condenser OffGas once every4 hours to provide an indication of primary-to-secondary leakage.
Subsequent sample frequency shall be in accordance with Table 1 based on the last sampleresult. Otherwise, analyze grab samples of the reactor coolant system andCondenser OffGas to provide an indication of primary-to-secondary leakage atthe minimum frequency indicated in Table 1, below:
CY-TM-170-300 Revision 3Page 29 of 209Table 2.1-2Notations (Cont'd)Table 1Minimum Frequency of Grab Samples When No Condenser Vent System Low RangeNoble Gas Activity Monitor is OperableExisting TotalPrimary-to-Secondary Leak Rate Frequency of Grab Samples(based on last monitor readingor sample result)0 to < 5 GPD Once per 24 hours5 to < 30 GPD Once per 12 hours30 to < 75 GPD Once per 4 hours75 GPD or greater Place the unit in at least HOT STANDBY within thenext 6 hours, and at least HOT SHUTDOWN withinthe following 6 hours, and at least COLDSHUTDOWN within the subsequent 24 hours.*Unstable is defined as > 10% increase during a 1 hour period, as stated in the EPRIGuidelines.
Condenser Vent System Low Range Noble Gas Activity Monitor inoperable channels should be restored to operability as rapidly as practical.
Condenser Vent System Low Range Noble Gas Activity Monitor inoperable channels should be restored to operability as rapidly as practical.
After 14 days, if one OPERABLE channel is not returned to service, within Ihour, the provisions of Technical Specification 3.0.1 apply, as if thisControl were a Tech Spec Limiting Condition for Operation.
After 14 days, if one OPERABLE channel is not returned to service, within I hour, the provisions of Technical Specification 3.0.1 apply, as if this Control were a Tech Spec Limiting Condition for Operation.
ACTION 33With the number of channels OPERABLE less than required by the MinimumChannels OPERABLE requirement, either restore the inoperable channel toOPERABLE status within 7 days, or prepare and submit a special report within30 days outlining the action(s) taken, the cause of the inoperability, and plansand schedule for restoring the system to OPERABLE status.
ACTION 33 With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, either restore the inoperable channel to OPERABLE status within 7 days, or prepare and submit a special report within 30 days outlining the action(s) taken, the cause of the inoperability, and plans and schedule for restoring the system to OPERABLE status.
CY-TM-170-300 Revision 3Page 30 of 2092.2 Radioactive Effluent Controls2.2.1 Liquid Effluent Controls2.2.1.1 Liquid Effluent Concentration CONTROL:The concentration of radioactive material released at anytimefrom the unit to unrestricted areas shall be limited to ten timesthe concentrations specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2, Column 2 for radionuclides other thandissolved or entrained noble gases. For dissolved orentrained noble gases, the concentration shall be limited to3E-3 uCi/cc total activity.
CY-TM-170-300 Revision 3 Page 30 of 209 2.2 Radioactive Effluent Controls 2.2.1 Liquid Effluent Controls 2.2.1.1 Liquid Effluent Concentration CONTROL: The concentration of radioactive material released at anytime from the unit to unrestricted areas shall be limited to ten times the concentrations specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2, Column 2 for radionuclides other than dissolved or entrained noble gases. For dissolved or entrained noble gases, the concentration shall be limited to 3E-3 uCi/cc total activity.APPLICABILITY:
APPLICABILITY:
At all times ACTION: With the concentration of radioactive material released from the unit to unrestricted areas exceeding the above limits, immediately restore concentrations within the above limits.BASES This control is provided to ensure that the concentration of radioactive materials released in liquid waste effluent from the unit to unrestricted areas will be less than ten times the concentration levels specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2. This limitation provides additional assurance that the levels of radioactive materials in bodies of water outside the site will not result in exposures with (1) the Section II.A design objectives of Appendix 1, 10 CFR Part 50, to a MEMBER OF THE PUBLIC and (2) the limits of 10 CFR Part 20.1301 to the population.
At all timesACTION:With the concentration of radioactive material released fromthe unit to unrestricted areas exceeding the above limits,immediately restore concentrations within the above limits.BASESThis control is provided to ensure that the concentration ofradioactive materials released in liquid waste effluent from theunit to unrestricted areas will be less than ten times theconcentration levels specified in 10 CFR Part20.1001-20.2401, Appendix B, Table 2. This limitation provides additional assurance that the levels of radioactive materials in bodies of water outside the site will not result inexposures with (1) the Section II.A design objectives ofAppendix 1, 10 CFR Part 50, to a MEMBER OF THE PUBLICand (2) the limits of 10 CFR Part 20.1301 to the population.
The concentration limit for noble gases is based upon the assumption the Xe-1 35 is the controlling radioisotope and its MPC in air (submersion) was converted to an equivalent concentration in water using the methods described in International Commission on Radiological Protection (ICRP)Publication  
The concentration limit for noble gases is based upon theassumption the Xe-1 35 is the controlling radioisotope and itsMPC in air (submersion) was converted to an equivalent concentration in water using the methods described inInternational Commission on Radiological Protection (ICRP)Publication  
: 2.
: 2.
CY-TM-170-300 Revision 3Page 31 of 2092.2.1.2 Liquid Effluent DoseCONTROLThe dose or dose commitment to a MEMBER OF THEPUBLIC from radioactive materials in liquid effluents releasedfrom the unit to the SITE BOUNDARY shall be limited:a. During any calendar quarter to less than or equal to1.5 mrem to the total body and to less than or equalto 5 mrem to any organ.b. During any calendar year to less than or equal to3 mrem to the total body and to less than or equal to10 mrem to any organ.APPLICABILITY:
CY-TM-170-300 Revision 3 Page 31 of 209 2.2.1.2 Liquid Effluent Dose CONTROL The dose or dose commitment to a MEMBER OF THE PUBLIC from radioactive materials in liquid effluents released from the unit to the SITE BOUNDARY shall be limited: a. During any calendar quarter to less than or equal to 1.5 mrem to the total body and to less than or equal to 5 mrem to any organ.b. During any calendar year to less than or equal to 3 mrem to the total body and to less than or equal to 10 mrem to any organ.APPLICABILITY:
At all timesACTION:a. With the calculated dose from the release ofradioactive materials in liquid effluents exceeding any of the above limits, prepare and submit to theNRC Region I Administrator within 30 days, aSpecial Report, which identifies the cause(s) forexceeding the limit(s),
At all times ACTION: a. With the calculated dose from the release of radioactive materials in liquid effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report, which identifies the cause(s) for exceeding the limit(s), and defines the corrective actions to be taken to reduce the releases of radioactive materials in liquid effluents during the remainder of the current calendar quarter and during the subsequent 3 calendar quarters so that the cumulative dose or dose commitment to any individual from such releases during these four calendar quarters is within 3 mrem to the total body and 10 mrem to any organ. This Special Report shall also include (1) the result of radiological analyses of the drinking water source, and (2) the radiological impact on finished drinking water supplies with regard to the requirements of 40 CFR 141, Safe Drinking Water Act.
and defines the corrective actions to be taken to reduce the releases ofradioactive materials in liquid effluents during theremainder of the current calendar quarter andduring the subsequent 3 calendar quarters so thatthe cumulative dose or dose commitment to anyindividual from such releases during these fourcalendar quarters is within 3 mrem to the total bodyand 10 mrem to any organ. This Special Reportshall also include (1) the result of radiological analyses of the drinking water source, and (2) theradiological impact on finished drinking watersupplies with regard to the requirements of 40 CFR141, Safe Drinking Water Act.
CY-TM-1 70-300 Revision 3 Page 32 of 209 BASES This control and associated action is provided to implement the requirements of Sections II.A, Ill.A, and IV.A of Appendix I, 10 CFR Part 50. The Control implements the guides set forth in Section II.A of Appendix I. The ACTION statements provide the required operating flexibility and at the same time implement the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive material in liquid effluents will be kept "as low as is reasonably achievable".
CY-TM-1 70-300Revision 3Page 32 of 209BASESThis control and associated action is provided to implement the requirements of Sections II.A, Ill.A, and IV.A of Appendix I,10 CFR Part 50. The Control implements the guides set forthin Section II.A of Appendix I. The ACTION statements providethe required operating flexibility and at the same timeimplement the guides set forth in Section IV.A of Appendix I toassure that the releases of radioactive material in liquideffluents will be kept "as low as is reasonably achievable".
Also, for fresh water sites with drinking water supplies which can be potentially affected by plant operations, there is reasonable assurance that the operation of the facility will not result in radionuclide concentrations in the finished drinking water that are in excess of the requirements of 10 CFR 20.The dose calculations in the ODCM implement the requirements in Section III.A. of Appendix I that conformance with the guides of Appendix I is to be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.
Also, for fresh water sites with drinking water supplies whichcan be potentially affected by plant operations, there isreasonable assurance that the operation of the facility will notresult in radionuclide concentrations in the finished drinkingwater that are in excess of the requirements of 10 CFR 20.The dose calculations in the ODCM implement therequirements in Section III.A. of Appendix I that conformance with the guides of Appendix I is to be shown by calculational procedures based on models and data such that the actualexposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.
The equations specified in the ODCM for calculating the doses due to the actual release rates of radioactive materials in liquid effluents are consistent with the methodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October, 1977, and Regulatory Guide 1.113,"Estimating Aquatic Dispersion of Effluents from Accidental and Routine Reactor Releases for the Purpose of Implementing Appendix I," April, 1977. NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.113.
Theequations specified in the ODCM for calculating the doses dueto the actual release rates of radioactive materials in liquideffluents are consistent with the methodology provided inRegulatory Guide 1.109, "Calculation of Annual Doses to Manfrom Routine Releases of Reactor Effluents for the Purpose ofEvaluating Compliance with 10 CFR Part 50, Appendix I,"Revision 1, October, 1977, and Regulatory Guide 1.113,"Estimating Aquatic Dispersion of Effluents from Accidental and Routine Reactor Releases for the Purpose ofImplementing Appendix I," April, 1977. NUREG-0133 provides methods for dose calculations consistent withRegulatory Guides 1.109 and 1.113.
CY-TM-170-300 Revision 3 Page 33 of 209 2.2.1.3 Liquid Radwaste Treatment System CONTROL: The appropriate portions of the liquid radwaste treatment system shall be used to reduce the radioactive materials in liquid wastes prior to their discharge when the projected doses due to the liquid effluent from the unit to unrestricted areas would exceed 0.06 mrem to the total body or 0.2 mrem to any organ in any calendar month.APPLICABILITY:
CY-TM-170-300 Revision 3Page 33 of 2092.2.1.3 Liquid Radwaste Treatment SystemCONTROL:The appropriate portions of the liquid radwaste treatment system shall be used to reduce the radioactive materials inliquid wastes prior to their discharge when the projected dosesdue to the liquid effluent from the unit to unrestricted areaswould exceed 0.06 mrem to the total body or 0.2 mrem to anyorgan in any calendar month.APPLICABILITY:
At all times ACTION: a. With radioactive liquid waste being discharged without treatment and in excess of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which includes the following information:
At all timesACTION:a. With radioactive liquid waste being discharged without treatment and in excess of the above limits,prepare and submit to the NRC Region IAdministrator within 30 days, a Special Reportwhich includes the following information:
: 1. Explanation of why liquid radwaste was being discharged without treatment, identification of any inoperable equipment or subsystems, and the reason for inoperability, 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and, 3. A summary description of action(s) taken to prevent a recurrence BASES The requirement that the appropriate portions of this system be used, when specified, provides assurance that the releases of radioactive materials in liquid effluents will be kept as low as is reasonably achievable.
: 1. Explanation of why liquid radwaste wasbeing discharged without treatment, identification of any inoperable equipment or subsystems, and the reason forinoperability,
This control implements the requirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50 and the design objective given in Section II.D of Appendix I to 10 CFR Part 50. The intent of Section ll.D. is to reduce effluents to as low as is reasonably achievable in a cost effective manner. This control satisfies this intent by establishing a dose limit which is a small fraction (25%) of Section II.A of Appendix 1, 10 CFR Part 50 dose requirements.
: 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and,3. A summary description of action(s) takento prevent a recurrence BASESThe requirement that the appropriate portions of this systembe used, when specified, provides assurance that the releasesof radioactive materials in liquid effluents will be kept as low asis reasonably achievable.
This margin, a factor of 4, constitutes a reasonable reduction.
This control implements therequirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50 and the design objective given in Section II.D of Appendix I to 10 CFR Part 50. Theintent of Section ll.D. is to reduce effluents to as low as isreasonably achievable in a cost effective manner. This controlsatisfies this intent by establishing a dose limit which is a smallfraction (25%) of Section II.A of Appendix 1, 10 CFR Part 50dose requirements.
CY-TM-1 70-300 Revision 3 Page 34 of 209 2.2.1.4 Liquid Holdup Tanks CONTROL The quantity of radioactive material contained in each of the following tanks shall be limited to less than or equal to 10 curies, excluding tritium and dissolved or entrained noble gases.a. Outside temporary tank APPLICABILITY:
This margin, a factor of 4, constitutes areasonable reduction.
At all times.ACTION: a. With the quantity of radioactive material in any of the above listed tanks exceeding the above limit, immediately suspend all additions of radioactive material to the tank and within 48 hours reduce the tank contents to within the limit.BASES Restricting the quantity of radioactive material contained in the specified tanks provides assurance that in the event of an uncontrolled release of the tanks' contents, the resulting concentrations would be less than the limits of 10 CFR Part 20.1001-20-20.2401, Appendix B, Table 2, Column 2, at the nearest potable water supply and the nearest surface water supply in an unrestricted area.2.2.2 Gaseous Effluent Controls 2.2.2.1 Gaseous Effluent Dose Rate CONTROL: The dose rate due to radioactive materials released in gaseous effluent from the site shall be limited to the following:
CY-TM-1 70-300Revision 3Page 34 of 2092.2.1.4 Liquid Holdup TanksCONTROLThe quantity of radioactive material contained in each of thefollowing tanks shall be limited to less than or equal to 10curies, excluding tritium and dissolved or entrained noblegases.a. Outside temporary tankAPPLICABILITY:
: a. For noble gases: less than or equal to 500 mrem/yr to the total body and less than or equal to 3000 mrem/yr to the skin, and b. For 1-131, 1-133, tritium and all radionuclides in particulate form with half lives greater than 8 days: less than or equal to 1500 mrem/yr to any organ.APPLICABILITY:
At all times.ACTION:a. With the quantity of radioactive material in any ofthe above listed tanks exceeding the above limit,immediately suspend all additions of radioactive material to the tank and within 48 hours reduce thetank contents to within the limit.BASESRestricting the quantity of radioactive material contained in thespecified tanks provides assurance that in the event of anuncontrolled release of the tanks' contents, the resulting concentrations would be less than the limits of 10 CFR Part20.1001-20-20.2401, Appendix B, Table 2, Column 2, at thenearest potable water supply and the nearest surface watersupply in an unrestricted area.2.2.2 Gaseous Effluent Controls2.2.2.1 Gaseous Effluent Dose RateCONTROL:The dose rate due to radioactive materials released ingaseous effluent from the site shall be limited to the following:
At all times CY-TM-1 70-300 Revision 3 Page 35 of 209 ACTION: With the release rate(s) exceeding the above limits, immediately decrease the release rate to comply with the above limit(s).BASES The control implements the requirement in Technical Specification (6.8.4.b (7). This specification is provided to ensure that the dose from radioactive materials in gaseous effluents at and beyond the SITE BOUNDARY will be within the annual dose limits of 10 CFR Part 20. The annual dose limits are the doses associated with 10 times the concentrations of 10 CFR Part 20, Appendix B, Table 2, Column 1. These limits provide reasonable assurance that radioactive material discharged in gaseous effluents will not result in the exposure of a MEMBER OF THE PUBLIC, either within or outside the SITE BOUNDARY, to annual average concentrations exceeding the limits specified in Appendix B, Table 2 of 10 CFR Part 20.1302. For MEMBERS OF THE PUBLIC who may at times be within the SITE BOUNDARY, the occupancy of the MEMBER OF THE PUBLIC will be sufficiently low to compensate for any increase in the atmospheric diffusion factor above that for the exclusion area boundary.
: a. For noble gases: less than or equal to 500 mrem/yrto the total body and less than or equal to 3000mrem/yr to the skin, andb. For 1-131, 1-133, tritium and all radionuclides inparticulate form with half lives greater than 8 days:less than or equal to 1500 mrem/yr to any organ.APPLICABILITY:
The specified release rate limits restrict, at all times, the corresponding gamma and beta dose rates above background to a MEMBER OF THE PUBLIC at or beyond the SITE BOUNDARY to less than or equal to 500 mrem/year to the total body, or to less than or equal to 3000 mrem/year to the skin. These release rate limits also restrict, at all times, the corresponding thyroid dose rate above background to a child via the inhalation pathway to less than or equal to 1500 mrem/year (NUREG 1301).2.2.2.2 Gaseous Effluents Dose-Noble Gases CONTROL: The air dose due to noble gases released in gaseous effluents from the unit to areas at and beyond the SITE BOUNDARY shall be limited to the following:
At all times CY-TM-1 70-300Revision 3Page 35 of 209ACTION:With the release rate(s) exceeding the above limits,immediately decrease the release rate to comply with theabove limit(s).
: a. During any calendar quarter: less than or equal to 5 mrad for gamma radiation and less than or equal to 10 mrad for beta radiation  
BASESThe control implements the requirement in Technical Specification (6.8.4.b (7). This specification is provided toensure that the dose from radioactive materials in gaseouseffluents at and beyond the SITE BOUNDARY will be withinthe annual dose limits of 10 CFR Part 20. The annual doselimits are the doses associated with 10 times theconcentrations of 10 CFR Part 20, Appendix B, Table 2,Column 1. These limits provide reasonable assurance thatradioactive material discharged in gaseous effluents will notresult in the exposure of a MEMBER OF THE PUBLIC, eitherwithin or outside the SITE BOUNDARY, to annual averageconcentrations exceeding the limits specified in Appendix B,Table 2 of 10 CFR Part 20.1302.
: and, CY-TM-1 70-300 Revision 3 Page 36 of 209 b. During any calendar year: less than or equal to 10 mrad for gamma radiation and less than or equal to 20 mrad for beta radiation.
For MEMBERS OF THEPUBLIC who may at times be within the SITE BOUNDARY, the occupancy of the MEMBER OF THE PUBLIC will besufficiently low to compensate for any increase in theatmospheric diffusion factor above that for the exclusion areaboundary.
The specified release rate limits restrict, at alltimes, the corresponding gamma and beta dose rates abovebackground to a MEMBER OF THE PUBLIC at or beyond theSITE BOUNDARY to less than or equal to 500 mrem/year tothe total body, or to less than or equal to 3000 mrem/year tothe skin. These release rate limits also restrict, at all times,the corresponding thyroid dose rate above background to achild via the inhalation pathway to less than or equal to 1500mrem/year (NUREG 1301).2.2.2.2 Gaseous Effluents Dose-Noble GasesCONTROL:The air dose due to noble gases released in gaseous effluents from the unit to areas at and beyond the SITE BOUNDARYshall be limited to the following:
: a. During any calendar quarter:
less than or equal to 5mrad for gamma radiation and less than or equal to10 mrad for beta radiation  
: and, CY-TM-1 70-300Revision 3Page 36 of 209b. During any calendar year: less than or equal to 10mrad for gamma radiation and less than or equal to20 mrad for beta radiation.
APPLICABILITY:
APPLICABILITY:
At all timesACTION:a. With the calculated air dose from radioactive noblegases in gaseous effluents exceeding any of theabove limits, prepare and submit to the NRC RegionI Administrator within 30 days, a Special Reportwhich identifies the cause(s) for exceeding thelimit(s) and defines the corrective actions that havebeen taken to reduce the releases and the proposedcorrective actions to be taken to assure thatsubsequent releases will be in compliance with theabove limits.BASESThis control applies to the release of radioactive materials ingaseous effluents from TMI-I.This control and associated action is provided to implement the requirements of Section II.B, III.A and IV.A of Appendix I,10 CFR Part 50. The Control implements the guides set forthin Section 1l.B of Appendix I. The ACTION statements providethe required operating flexibility and at the same timeimplement the guides set forth in Section IV.A of Appendix I toassure that the releases of radioactive material in gaseouseffluents will be kept "as low as is reasonably achievable."
At all times ACTION: a. With the calculated air dose from radioactive noble gases in gaseous effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit(s) and defines the corrective actions that have been taken to reduce the releases and the proposed corrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.BASES This control applies to the release of radioactive materials in gaseous effluents from TMI-I.This control and associated action is provided to implement the requirements of Section II.B, III.A and IV.A of Appendix I, 10 CFR Part 50. The Control implements the guides set forth in Section 1l.B of Appendix I. The ACTION statements provide the required operating flexibility and at the same time implement the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive material in gaseous effluents will be kept "as low as is reasonably achievable." The Surveillance Requirements implement the requirements in Section III.A of Appendix I that conformance with the guides of Appendix I be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through the appropriate pathways is unlikely to be substantially underestimated.
The Surveillance Requirements implement the requirements inSection III.A of Appendix I that conformance with the guides ofAppendix I be shown by calculational procedures based onmodels and data such that the actual exposure of a MEMBEROF THE PUBLIC through the appropriate pathways is unlikelyto be substantially underestimated.
The dose calculation methodology and parameters established in the ODCM for calculating the doses due to the actual release rates of radioactive noble gases in gaseous effluents are consistent with the methodology provided in Regulatory Guide 1.109,"Calculation of Annual Doses to Man from Routine Release of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977 and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in CY-TM-170-300 Revision 3 Page 37 of 209 Routine Releases from Light-Water Cooled Reactors", Revision 1, July 1977. The ODCM equations provided for determining the air doses at and beyond the SITE BOUNDARY are based upon the historical average atmospheric conditions.
The dose calculation methodology and parameters established in the ODCM forcalculating the doses due to the actual release rates ofradioactive noble gases in gaseous effluents are consistent with the methodology provided in Regulatory Guide 1.109,"Calculation of Annual Doses to Man from Routine Release ofReactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in CY-TM-170-300 Revision 3Page 37 of 209Routine Releases from Light-Water Cooled Reactors",
NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.111.2.2.2.3 Dose -Iodine-131, Iodine-133, Tritium, and Radionuclides in Particulate Form CONTROL: The dose to a MEMBER OF THE PUBLIC from Iodine-1 31, Iodine-133, Tritium, and all radionuclides in particulate form with half-lives greater than 8 days, in gaseous effluents released from the unit to areas at and beyond the SITE BOUNDARY shall be limited to the following:
Revision 1, July 1977. The ODCM equations provided fordetermining the air doses at and beyond the SITEBOUNDARY are based upon the historical averageatmospheric conditions.
: a. During any calendar quarter: less than or equal to 7.5 mrem to any organ, and b. During any calendar year: less than or equal to 15 mrem to any organ.APPLICABILITY:
NUREG-0133 provides methods fordose calculations consistent with Regulatory Guides 1.109and 1.111.2.2.2.3 Dose -Iodine-131, Iodine-133,  
At all times ACTION:.With the calculated dose from the release of Iodine-131, Iodine-1 33, Tritium, and radionuclides in particulate form with half-lives greater than 8 days, in gaseous effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit and defines the corrective actions that have been taken to reduce the releases and the proposed corrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.BASES This control applies to the release of radioactive materials in gaseous effluents from TMI-I.This control and associated action is provided to implement the requirements of Section II.C, III.A and IV.A of Appendix I, 10 CFR Part 50. The Controls are the guides set forth in CY-TM-1 70-300 Revision 3 Page 38 of 209 Section II.C of Appendix I. The ACTION statement provides the required operating flexibility and at the same time implements the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive materials in gaseous effluents will be kept "as low as is reasonably achievable." The ODCM calculational methods specified in the surveillance requirements implement the requirements in Section III.A of Appendix I that conformance with the guides of Appendix I be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.
: Tritium, and Radionuclides inParticulate FormCONTROL:The dose to a MEMBER OF THE PUBLIC from Iodine-1 31,Iodine-133,  
The ODCM calculational methodology and parameters for calculating the doses due to the actual release rates of the subject materials are consistent with the methodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October, 1977 and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors" Revision 1, July, 1977. These equations also provide for determining the actual doses based upon the historical average atmospheric conditions.
: Tritium, and all radionuclides in particulate formwith half-lives greater than 8 days, in gaseous effluents released from the unit to areas at and beyond the SITEBOUNDARY shall be limited to the following:
The release rate controls for iodine-131, iodine-133, tritium and radionuclides in particulate form with half lives greater than 8 days are dependent upon the existing radionuclide pathways to man, in areas at and beyond the SITE BOUNDARY.
: a. During any calendar quarter:
The pathways that were examined in the development of these calculations were: 1) individual inhalation of airborne radionuclides, 2) deposition of radionuclides onto green leafy vegetation with subsequent consumption by man, 3) deposition onto grassy areas where milk animals and meat producing animals graze with consumption of the milk and meat by man, and 4) deposition on the ground with subsequent exposure of man.2.2.2.4 Gaseous Radwaste Treatment System CONTROL The GASEOUS RADWASTE TREATMENT SYSTEM and the VENTILATION EXHAUST TREATMENT SYSTEM shall be OPERABLE.
less than or equal to7.5 mrem to any organ, andb. During any calendar year: less than or equal to 15mrem to any organ.APPLICABILITY:
The appropriate portions of the GASEOUS RADWASTE TREATMENT SYSTEM shall be used to reduce radioactive materials in the gaseous waste prior to their discharge when the monthlyprojected gaseous effluent air doses due to untreated gaseous effluent releases from the unit CY-TM-1 70-300 Revision 3 Page 39 of 209 would exceed 0.2 mrad for gamma radiation and 0.4 mrad for beta radiation.
At all timesACTION:.With the calculated dose from the release of Iodine-131, Iodine-1 33, Tritium, and radionuclides in particulate form withhalf-lives greater than 8 days, in gaseous effluents exceeding any of the above limits, prepare and submit to the NRCRegion I Administrator within 30 days, a Special Report whichidentifies the cause(s) for exceeding the limit and defines thecorrective actions that have been taken to reduce the releasesand the proposed corrective actions to be taken to assure thatsubsequent releases will be in compliance with the abovelimits.BASESThis control applies to the release of radioactive materials ingaseous effluents from TMI-I.This control and associated action is provided to implement the requirements of Section II.C, III.A and IV.A of Appendix I,10 CFR Part 50. The Controls are the guides set forth in CY-TM-1 70-300Revision 3Page 38 of 209Section II.C of Appendix I. The ACTION statement providesthe required operating flexibility and at the same timeimplements the guides set forth in Section IV.A of Appendix Ito assure that the releases of radioactive materials in gaseouseffluents will be kept "as low as is reasonably achievable."
The appropriate portions of the VENTILATION EXHAUST TREATMENT SYSTEM shall be used to reduce radioactive materials in gaseous waste prior to their discharge when the monthly projected doses due to gaseous effluent releases from the site would exceed 0.3 mrem to any organ.APPLICABILITY:
The ODCM calculational methods specified in the surveillance requirements implement the requirements in Section III.A ofAppendix I that conformance with the guides of Appendix I beshown by calculational procedures based on models and datasuch that the actual exposure of a MEMBER OF THE PUBLICthrough appropriate pathways is unlikely to be substantially underestimated.
At all times ACTION: a. With the GASEOUS RADWASTE TREATMENT SYSTEM and/or the VENTILATION EXHAUST TREATMENT SYSTEM inoperable for more than a month or with gaseous waste being discharged without treatment and in excess of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which includes the following information:
The ODCM calculational methodology andparameters for calculating the doses due to the actual releaserates of the subject materials are consistent with themethodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of ReactorEffluents for the Purpose of Evaluating Compliance with 10CFR Part 50, Appendix I," Revision 1, October, 1977 andRegulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in RoutineReleases from Light-Water-Cooled Reactors" Revision 1, July,1977. These equations also provide for determining the actualdoses based upon the historical average atmospheric conditions.
: 1. Identification of the inoperable equipment or subsystems and the reason for inoperability, 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and 3. A summary description of action(s) taken to prevent a recurrence BASES The use of the GASEOUS RADWASTE TREATMENT SYSTEM and the VENTILATION EXHAUST TREATMENT SYSTEM ensures that gaseous effluents are treated as appropriate prior to release to the environment.
The release rate controls for iodine-131, iodine-133, tritium and radionuclides in particulate form withhalf lives greater than 8 days are dependent upon the existingradionuclide pathways to man, in areas at and beyond theSITE BOUNDARY.
The appropriate portions of this system provide reasonable assurance that the releases of radioactive materials in gaseous effluents will be kept "as low as is reasonably achievable." This control implements the requirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50, and the design objectives given in Section II.D of Appendix I to 10 CFR Part 50. The specified limits governing the use of appropriate portions of the systems were specified as a suitable fraction of the guide set forth in Sections II.B and II.C of Appendix 1, 10 CFR Part 50, for gaseous effluents.
The pathways that were examined in thedevelopment of these calculations were: 1) individual inhalation of airborne radionuclides,  
CY-TM-1 70-300 Revision 3 Page 40 of 209 2.2.2.5 Explosive Gas Mixture CONTROL The concentration of oxygen in the Waste Gas Holdup System shall be limited to less than or equal to 2% by volume whenever the concentration of hydrogen in the Waste Gas Holdup System is greater than or equal to 4% by volume.AVAILABILITY:
: 2) deposition ofradionuclides onto green leafy vegetation with subsequent consumption by man, 3) deposition onto grassy areas wheremilk animals and meat producing animals graze withconsumption of the milk and meat by man, and 4) deposition on the ground with subsequent exposure of man.2.2.2.4 Gaseous Radwaste Treatment SystemCONTROLThe GASEOUS RADWASTE TREATMENT SYSTEM and theVENTILATION EXHAUST TREATMENT SYSTEM shall beOPERABLE.
At all times ACTION: Whenever the concentration of hydrogen in the Waste Gas Holdup System is greater than or equal to 4% by volume, and: a. The concentration of oxygen in the Waste Gas Holdup System is greater than 2% by volume, but less than 4% by volume, without delay, begin to reduce the oxygen concentration to within its limit.b. The concentration of oxygen in the Waste Gas Holdup System is greater than or equal to 4% by volume, immediately suspend additions of waste gas to the Waste Gas Holdup System and without delay, begin to reduce the oxygen concentration to within its limit.BASES: Based on experimental data (Reference 1), lower limits of flammability for hydrogen is 5% and for oxygen is 5% by volume. Therefore, if the concentration of either gas is kept below it lower limit, the other gas may be present in higher amounts without the danger of an explosive mixture.Maintaining the concentrations of hydrogen and oxygen such that an explosive mixture does not occur in the waste gas holdup system provides assurance that the release of radioactive materials will be controlled in conformance with the requirements of General Design Criterion 60 of Appendix A to 10 CFR 50.REFERENCES (1) Bulletin 503, Bureau of Mines; Limits of Flammability of Gases and Vapors CY-TM-1 70-300 Revision 3 Page 41 of 209 2.2.2.6 Waste Gas Decay Tanks CONTROL: The quantity of radioactivity contained in each waste gas decay tank shall be limited to less than or equal to 8800 curies noble gases (considered as Xe-1 33).APPLICABILITY:
The appropriate portions of the GASEOUSRADWASTE TREATMENT SYSTEM shall be used to reduceradioactive materials in the gaseous waste prior to theirdischarge when the monthlyprojected gaseous effluent airdoses due to untreated gaseous effluent releases from the unit CY-TM-1 70-300Revision 3Page 39 of 209would exceed 0.2 mrad for gamma radiation and 0.4 mrad forbeta radiation.
At all times ACTION: a. With the quantity of radioactive material in any waste gas decay tank exceeding the above limit, immediately suspend all additions of radioactive material to the tank and within 48 hours reduce the tank contents to within the limit.BASES Restricting the quantity of radioactivity contained in each waste gas decay tank provides assurance that in the event of an uncontrolled release of the tanks contents, the resulting total body exposure to a MEMBER OF THE PUBLIC at the nearest exclusion area boundary will not exceed 0.5 rem.This is consistent with Standard Review Plan 15.7.1, "Waste Gas System Failure." 2.2.3 Total Radioactive Effluent Controls 2.2.3.1 Total Dose CONTROL: The annual (calendar year) dose or dose commitment to any MEMBER OF THE PUBLIC, due.to releases of radioactivity and to radiation from uranium fuel cycle sources shall be limited to less than or equal to 25 mrem to the total body or any organ except the thyroid, which shall be limited to less than or equal to 75 mrem.APPLICABILITY:
The appropriate portions of the VENTILATION EXHAUST TREATMENT SYSTEM shall be used to reduceradioactive materials in gaseous waste prior to their discharge when the monthly projected doses due to gaseous effluentreleases from the site would exceed 0.3 mrem to any organ.APPLICABILITY:
At all times ACTION: With the calculated dose from the release of radioactive materials in liquid or gaseous effluents exceeding twice the limits of Controls 2.2.1.2.a, 2.2.1.2.b, 2.2.2.2.a, 2.2.2.2.b, 2.2.2.3.a, or, 2.2.2.3.b, calculations should be made including CY-TM-1 70-300 Revision 3 Page 42 of 209 direct radiation contributions from the unit and from outside storage tanks to determine whether the above limits of Control 2.2.3.1 have been exceeded.
At all timesACTION:a. With the GASEOUS RADWASTE TREATMENT SYSTEM and/or the VENTILATION EXHAUSTTREATMENT SYSTEM inoperable for more than amonth or with gaseous waste being discharged without treatment and in excess of the above limits,prepare and submit to the NRC Region IAdministrator within 30 days, a Special Reportwhich includes the following information:
If such is the case, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which defines the corrective action to be taken to reduce subsequent releases to prevent recurrence of exceeding the above limits and includes the schedule for achieving conformance with the above limits. This Special Report, as defined in 10 CFR Part 20.2203(b), shall include an analysis which estimates the radiation exposure (dose) to a MEMBER OF THE PUBLIC from uranium fuel cycle sources, including all effluent pathways and direct radiation, for the calendar year that includes the release(s) covered by this report. It shall also describe levels of radiation and concentrations of radioactive material involved, and the cause of the exposure levels or concentrations.
: 1. Identification of the inoperable equipment or subsystems and the reason forinoperability,
If the estimated dose(s) exceed the above limits, and if the release condition resulting in violation of 40 CFR 190 has not already been corrected, the Special Report shall include a request for a variance in accordance with the provisions of 40 CFR 190.Submittal of the report is considered a timely request, and a variance is granted until staff action on the request is complete.BASES This control is provided to meet the dose limitations of 40 CFR Part 190 that have been incorporated into 10 CFR Part 20.1301(d).
: 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and3. A summary description of action(s) takento prevent a recurrence BASESThe use of the GASEOUS RADWASTE TREATMENT SYSTEM and the VENTILATION EXHAUST TREATMENT SYSTEM ensures that gaseous effluents are treated asappropriate prior to release to the environment.
This control requires the preparation and submittal of a Special Report whenever the calculated doses from plant generated radioactive effluents and direct radiation exceed 25 mrem to the total body or any organ, except the thyroid, which shall be limited to less than or equal to 75 mrem. For sites containing up to 4 reactors, it is highly unlikely that the resultant dose to a MEMBER OF THE PUBLIC will exceed the dose limits of 40 CFR Part 190 if the individual reactors remain within twice the dose design objectives of Appendix I, and if direct radiation doses from the reactor units and outside storage tanks are kept small. The Special Report will describe a course of action that should result in the limitation of the annual dose to a MEMBER OF THE PUBLIC to within the 40 CFR Part 190 limits. For the purposes of the Special Report, it may be assumed that the dose commitment to the member of the public from other uranium fuel cycle sources is negligible, with the exception that dose contributions from other nuclear fuel cycle facilities at the same site or within a radius of 8 km must be CY-TM-170-300 Revision 3 Page 43 of 209 considered.
Theappropriate portions of this system provide reasonable assurance that the releases of radioactive materials ingaseous effluents will be kept "as low as is reasonably achievable."
If the dose to any member of the public is estimated to exceed the requirements of 40 CFR Part 190, the Special Report with a request for a variance (provided the release conditions resulting in violation of 40 CFR Part 190 have not already been corrected) in accordance with the provisions of 40 CFR Part 190.11 and 10 CFR Part 20.2203(b), is considered to be a timely request and fulfills the requirements of 40 CFR Part 190 until NRC staff action is completed.
This control implements the requirements of 10CFR Part 50.36a, General Design Criterion 60 of Appendix Ato 10 CFR Part 50, and the design objectives given in SectionII.D of Appendix I to 10 CFR Part 50. The specified limitsgoverning the use of appropriate portions of the systems werespecified as a suitable fraction of the guide set forth inSections II.B and II.C of Appendix 1, 10 CFR Part 50, forgaseous effluents.
The variance only relates to the limits of 40 CFR Part 190, and does not apply in any way to the other requirements for dose limitation of 10 CFR Part 20, as addressed in Controls 2.2.1.1 and 2.2.2.1. An individual is not considered a MEMBER OF THE PUBLIC during any period in which he/she is engaged in carrying out any operation that is part of the nuclear fuel cycle.
CY-TM-1 70-300Revision 3Page 40 of 2092.2.2.5 Explosive Gas MixtureCONTROLThe concentration of oxygen in the Waste Gas Holdup Systemshall be limited to less than or equal to 2% by volumewhenever the concentration of hydrogen in the Waste GasHoldup System is greater than or equal to 4% by volume.AVAILABILITY:
CY-TM-1 70-300 Revision 3 Page 44 of 209 3.0 SURVEILLANCES 3.1 Radioactive Effluent Instrumentation 3.1.1 Radioactive Liquid Effluent Instrumentation Surveillance Requirements 3.1.1.1 Each radioactive liquid effluent monitoring instrumentation channel shall be demonstrated OPERABLE by performance of the CHANNEL CHECK, SOURCE CHECK, CHANNEL CALIBRATION, AND CHANNEL TEST operations during the MODES and at the frequencies shown in Table 3.1-1.
At all timesACTION:Whenever the concentration of hydrogen in the Waste GasHoldup System is greater than or equal to 4% by volume, and:a. The concentration of oxygen in the Waste GasHoldup System is greater than 2% by volume, butless than 4% by volume, without delay, begin toreduce the oxygen concentration to within its limit.b. The concentration of oxygen in the Waste GasHoldup System is greater than or equal to 4% byvolume, immediately suspend additions of wastegas to the Waste Gas Holdup System and withoutdelay, begin to reduce the oxygen concentration towithin its limit.BASES:Based on experimental data (Reference 1), lower limits offlammability for hydrogen is 5% and for oxygen is 5% byvolume. Therefore, if the concentration of either gas is keptbelow it lower limit, the other gas may be present in higheramounts without the danger of an explosive mixture.Maintaining the concentrations of hydrogen and oxygen suchthat an explosive mixture does not occur in the waste gasholdup system provides assurance that the release ofradioactive materials will be controlled in conformance with therequirements of General Design Criterion 60 of Appendix A to10 CFR 50.REFERENCES (1) Bulletin 503, Bureau of Mines; Limits of Flammability of Gasesand Vapors CY-TM-1 70-300Revision 3Page 41 of 2092.2.2.6 Waste Gas Decay TanksCONTROL:The quantity of radioactivity contained in each waste gasdecay tank shall be limited to less than or equal to 8800 curiesnoble gases (considered as Xe-1 33).APPLICABILITY:
CY-TM-1 70-300 Revision 3 Page 45 of 209 Table 3.1-1 Radioactive Liquid Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL INSTRUMENT CHECK CHECK CALIBRATION
At all timesACTION:a. With the quantity of radioactive material in anywaste gas decay tank exceeding the above limit,immediately suspend all additions of radioactive material to the tank and within 48 hours reduce thetank contents to within the limit.BASESRestricting the quantity of radioactivity contained in eachwaste gas decay tank provides assurance that in the event ofan uncontrolled release of the tanks contents, the resulting total body exposure to a MEMBER OF THE PUBLIC at thenearest exclusion area boundary will not exceed 0.5 rem.This is consistent with Standard Review Plan 15.7.1, "WasteGas System Failure."
: 1. Radioactivity Monitors Providing Alarm and Automatic Isolation a. Unit 1 Liquid Radwaste Effluents Line (RM-L-6)b. IWTS/IWFS Discharge Line (RM-L-12)2. Flow Rate Monitors a. Unit 1 Liquid Radwaste Effluent Line (WDL-FT-84)
2.2.3 Total Radioactive Effluent Controls2.2.3.1 Total DoseCONTROL:The annual (calendar year) dose or dose commitment to anyMEMBER OF THE PUBLIC, due.to releases of radioactivity and to radiation from uranium fuel cycle sources shall belimited to less than or equal to 25 mrem to the total body orany organ except the thyroid, which shall be limited to lessthan or equal to 75 mrem.APPLICABILITY:
At all timesACTION:With the calculated dose from the release of radioactive materials in liquid or gaseous effluents exceeding twice thelimits of Controls 2.2.1.2.a, 2.2.1.2.b, 2.2.2.2.a, 2.2.2.2.b, 2.2.2.3.a, or, 2.2.2.3.b, calculations should be made including CY-TM-1 70-300Revision 3Page 42 of 209direct radiation contributions from the unit and from outsidestorage tanks to determine whether the above limits of Control2.2.3.1 have been exceeded.
If such is the case, prepare andsubmit to the NRC Region I Administrator within 30 days, aSpecial Report which defines the corrective action to be takento reduce subsequent releases to prevent recurrence ofexceeding the above limits and includes the schedule forachieving conformance with the above limits. This SpecialReport, as defined in 10 CFR Part 20.2203(b),
shall include ananalysis which estimates the radiation exposure (dose) to aMEMBER OF THE PUBLIC from uranium fuel cycle sources,including all effluent pathways and direct radiation, for thecalendar year that includes the release(s) covered by thisreport. It shall also describe levels of radiation andconcentrations of radioactive material  
: involved, and the causeof the exposure levels or concentrations.
If the estimated dose(s) exceed the above limits, and if the release condition resulting in violation of 40 CFR 190 has not already beencorrected, the Special Report shall include a request for avariance in accordance with the provisions of 40 CFR 190.Submittal of the report is considered a timely request, and avariance is granted until staff action on the request iscomplete.
BASESThis control is provided to meet the dose limitations of 40 CFRPart 190 that have been incorporated into 10 CFR Part20.1301(d).
This control requires the preparation andsubmittal of a Special Report whenever the calculated dosesfrom plant generated radioactive effluents and direct radiation exceed 25 mrem to the total body or any organ, except thethyroid, which shall be limited to less than or equal to 75mrem. For sites containing up to 4 reactors, it is highlyunlikely that the resultant dose to a MEMBER OF THEPUBLIC will exceed the dose limits of 40 CFR Part 190 if theindividual reactors remain within twice the dose designobjectives of Appendix I, and if direct radiation doses from thereactor units and outside storage tanks are kept small. TheSpecial Report will describe a course of action that shouldresult in the limitation of the annual dose to a MEMBER OFTHE PUBLIC to within the 40 CFR Part 190 limits. For thepurposes of the Special Report, it may be assumed that thedose commitment to the member of the public from otheruranium fuel cycle sources is negligible, with the exception that dose contributions from other nuclear fuel cycle facilities at the same site or within a radius of 8 km must be CY-TM-170-300 Revision 3Page 43 of 209considered.
If the dose to any member of the public isestimated to exceed the requirements of 40 CFR Part 190, theSpecial Report with a request for a variance (provided therelease conditions resulting in violation of 40 CFR Part 190have not already been corrected) in accordance with theprovisions of 40 CFR Part 190.11 and 10 CFR Part20.2203(b),
is considered to be a timely request and fulfills therequirements of 40 CFR Part 190 until NRC staff action iscompleted.
The variance only relates to the limits of 40 CFRPart 190, and does not apply in any way to the otherrequirements for dose limitation of 10 CFR Part 20, asaddressed in Controls 2.2.1.1 and 2.2.2.1.
An individual is notconsidered a MEMBER OF THE PUBLIC during any period inwhich he/she is engaged in carrying out any operation that ispart of the nuclear fuel cycle.
CY-TM-1 70-300Revision 3Page 44 of 2093.0 SURVEILLANCES 3.1 Radioactive Effluent Instrumentation 3.1.1 Radioactive Liquid Effluent Instrumentation Surveillance Requirements 3.1.1.1 Each radioactive liquid effluent monitoring instrumentation channel shall be demonstrated OPERABLE by performance ofthe CHANNEL CHECK, SOURCE CHECK, CHANNELCALIBRATION, AND CHANNEL TEST operations during theMODES and at the frequencies shown in Table 3.1-1.
CY-TM-1 70-300Revision 3Page 45 of 209Table 3.1-1Radioactive Liquid Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNELINSTRUMENT CHECK CHECK CALIBRATION
: 1. Radioactivity Monitors Providing Alarm and Automatic Isolation
: a. Unit 1 Liquid Radwaste Effluents Line (RM-L-6)b. IWTS/IWFS Discharge Line (RM-L-12)
: 2. Flow Rate Monitorsa. Unit 1 Liquid Radwaste Effluent Line (WDL-FT-84)
: b. Station Effluent Discharge (SR-FT-146)
: b. Station Effluent Discharge (SR-FT-146)
DDD(3)D(3)PPN/AN/AR(2)R(2)RRCHANNELTESTQ(1)Q(1)QQ CY-TM-1 70-300Revision 3Page 46 of 209Table 3.1-1 (Cont'd)Table Notation(1) The CHANNEL TEST shall also demonstrate that automatic isolation of this pathwayand control room alarm annunciation occurs if the following condition exists:1. Instrument indicates measured levels above the high alarm/trip setpoint.
D D D(3)D(3)P P N/A N/A R(2)R(2)R R CHANNEL TEST Q(1)Q(1)Q Q CY-TM-1 70-300 Revision 3 Page 46 of 209 Table 3.1-1 (Cont'd)Table Notation (1) The CHANNEL TEST shall also demonstrate that automatic isolation of this pathway and control room alarm annunciation occurs if the following condition exists: 1. Instrument indicates measured levels above the high alarm/trip setpoint.(Includes  
(Includes  
-circuit failure)2. Instrument indicates a down scale failure. (Alarm function only.) (Includes  
-circuit failure)2. Instrument indicates a down scale failure.  
-circuit failure)3. Instrument controls moved from the operate mode (Alarm function only).(2) The initial CHANNEL CALIBRATION for radioactivity measurement instrumentation shall be performed using one or more of the reference standards certified by the National Institute of Standards and Technology or using standards that have been obtained from suppliers that participated in measurement assurance activities with NIST. These standards should permit calibrating the system over its intended range of energy and measurement range. For subsequent CHANNEL CALIBRATION, sources that have been related to the initial calibration should be used. (Operating plants may substitute previously established calibration procedures for this requirement)
(Alarm function only.) (Includes  
(3) CHANNEL CHECK shall consist of verifying indication of flow during periods of release.CHANNEL CHECK shall be made at least once daily on any day on which continuous, periodic, or batch releases are made.
-circuit failure)3. Instrument controls moved from the operate mode (Alarm function only).(2) The initial CHANNEL CALIBRATION for radioactivity measurement instrumentation shall be performed using one or more of the reference standards certified by theNational Institute of Standards and Technology or using standards that have beenobtained from suppliers that participated in measurement assurance activities withNIST. These standards should permit calibrating the system over its intended range ofenergy and measurement range. For subsequent CHANNEL CALIBRATION, sourcesthat have been related to the initial calibration should be used. (Operating plants maysubstitute previously established calibration procedures for this requirement)
CY-TM-170-300 Revision 3 Page 47 of 209 3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 3.1.2.1 Each radioactive gaseous process or effluent monitoring instrumentation channel shall be demonstrated OPERABLE by performance of the CHANNEL CHECK, SOURCE CHECK, CHANNEL CALIBRATION, and CHANNEL TEST operations at the frequencies shown in Table 3.1-2.
(3) CHANNEL CHECK shall consist of verifying indication of flow during periods of release.CHANNEL CHECK shall be made at least once daily on any day on which continuous,
CY-TM-1 70-300 Revision 3 Page 48 of 209 Table 3.1-2 Radioactive Gaseous Process and Effluent Monitorinq Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNEL INSTRUMENT CHECK CHECK CALIBRATION TEST APPLICABILITY
: periodic, or batch releases are made.
: 1. Waste Gas Holdup System a. Noble Gas Activity Monitor (RM-A7) P P E(3) Q(1)b. Effluent System Flow Rate Measuring Device (WDG-FT-123)
CY-TM-170-300 Revision 3Page 47 of 2093.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 3.1.2.1 Each radioactive gaseous process or effluent monitoring instrumentation channel shall be demonstrated OPERABLEby performance of the CHANNEL CHECK, SOURCE CHECK,CHANNEL CALIBRATION, and CHANNEL TEST operations at the frequencies shown in Table 3.1-2.
P N/A E Q 2. Waste Gas Holdup System Explosive Gas Monitoring System a. Hydrogen Monitor (CA-G-1A/B)
CY-TM-1 70-300Revision 3Page 48 of 209Table 3.1-2Radioactive Gaseous Process and Effluent Monitorinq Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNELINSTRUMENT CHECK CHECK CALIBRATION TEST APPLICABILITY
: 1. Waste Gas Holdup Systema. Noble Gas Activity Monitor (RM-A7) P P E(3) Q(1)b. Effluent System Flow Rate Measuring Device (WDG-FT-123)
P N/A E Q2. Waste Gas Holdup System Explosive Gas Monitoring Systema. Hydrogen Monitor (CA-G-1A/B)
D N/A Q(4) M **b. Oxygen Monitor (CA-G-1A/B)
D N/A Q(4) M **b. Oxygen Monitor (CA-G-1A/B)
D N/A Q(5) M **3. Containment Purge Vent Systema. Noble Gas Activity Monitor (RM-A9) D P E(3) M(1) #b. Iodine Sampler (RM-A9) W N/A N/A N/A #c. Particulate Sampler (RM-A9) W N/A N/A N/A #d. Effluent System Flow Rate Measuring Device (AH-FR-148)
D N/A Q(5) M **3. Containment Purge Vent System a. Noble Gas Activity Monitor (RM-A9) D P E(3) M(1) #b. Iodine Sampler (RM-A9) W N/A N/A N/A #c. Particulate Sampler (RM-A9) W N/A N/A N/A #d. Effluent System Flow Rate Measuring Device (AH-FR-148)
D N/A E Q #e. Sampler Flow Rate Monitor (RM-FI-1231)
D N/A E Q #e. Sampler Flow Rate Monitor (RM-FI-1231)
D N/A E N/A #4. Condenser Vent Systema. Noble Gas Activity Monitor (RM-A5 and Suitable Equivalent  
D N/A E N/A #4. Condenser Vent System a. Noble Gas Activity Monitor (RM-A5 and Suitable Equivalent  
-D M E(3) Q(2)See Table 2.1-2, Item 4.a)
-D M E(3) Q(2)See Table 2.1-2, Item 4.a)
CY-TM-1 70-300Revision 3Page 49 of 209Table 3.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNELINSTRUMENT
CY-TM-1 70-300 Revision 3 Page 49 of 209 Table 3.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNEL INSTRUMENT
: 5. Auxiliary and Fuel Handling Building Ventilation Systema. Noble Gas Activity Monitor (RM-A8) or (RM-A4 and RM-A6)b. Iodine Sampler (RM-A8) or (RM-A4 and RM-A6)c. Particulate Sampler (RM-A8) or (RM-A4 and RM-A6)d. System Effluent Flow Rate Measurement Devices (AH-FR-149 andAH-FR-1 50)e. Sampler Flow Rate Monitor (RM-FI-1230 or RM-A-4\FI and RM-A-6\FI)
: 5. Auxiliary and Fuel Handling Building Ventilation System a. Noble Gas Activity Monitor (RM-A8) or (RM-A4 and RM-A6)b. Iodine Sampler (RM-A8) or (RM-A4 and RM-A6)c. Particulate Sampler (RM-A8) or (RM-A4 and RM-A6)d. System Effluent Flow Rate Measurement Devices (AH-FR-149 and AH-FR-1 50)e. Sampler Flow Rate Monitor (RM-FI-1230 or RM-A-4\FI and RM-A-6\FI)
: 6. Fuel Handling Building ESF Air Treatment Systema. Noble Gas Activity Monitor (RM-A14)b. System Effluent Flow Rate (AH-UR-1104 A/B)c. Sampler Flow Rate Measurement Device (RM-A-14FI14)
: 6. Fuel Handling Building ESF Air Treatment System a. Noble Gas Activity Monitor (RM-A14)b. System Effluent Flow Rate (AH-UR-1104 A/B)c. Sampler Flow Rate Measurement Device (RM-A-14FI14)
CHECK CHECK CALIBRATION TESTDWWDDDDDMN/AN/AN/AN/AMN/AN/AE(3)N/AN/AEER(3)RRQ(1)N/AN/AQN/AAPPLICABILITY Q(2)QQ CY-TM-1 70-300Revision 3Page 50 of 209Table 3.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNELINSTRUMENT
CHECK CHECK CALIBRATION TEST D W W D D D D D M N/A N/A N/A N/A M N/A N/A E(3)N/A N/A E E R(3)R R Q(1)N/A N/A Q N/A APPLICABILITY Q(2)Q Q CY-TM-1 70-300 Revision 3 Page 50 of 209 Table 3.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNEL INSTRUMENT
: 7. Chemical Cleaning Building Ventilation Systema. Noble Gas Activity Monitor (ALC RM-1-18)b. Iodine Sampler (ALC RM-1-18)c. Particulate Sampler (ALC RM-1-18)8. Waste Handling and Packaging Facility Ventilation Systema. Particulate Sampler (WHP-RIT-1)
: 7. Chemical Cleaning Building Ventilation System a. Noble Gas Activity Monitor (ALC RM-1-18)b. Iodine Sampler (ALC RM-1-18)c. Particulate Sampler (ALC RM-1-18)8. Waste Handling and Packaging Facility Ventilation System a. Particulate Sampler (WHP-RIT-1)
: 9. Respirator and Laundry Maintenance Ventilation Systema. Particulate Sampler (RLM-RM-1)
: 9. Respirator and Laundry Maintenance Ventilation System a. Particulate Sampler (RLM-RM-1)
CHECK CHECK CALIBRATION TEST AlPPLICABILITY DWWDMN/AN/AWE(3)N/AN/ASAQ(2)N/AN/AWD WSA W CY-TM-170-300 Revision 3Page 51 of 209Table 3.1-2 (Cont'd)Table Notation* At all times** During waste gas holdup system operation Operability is not required when discharges are positively controlled through theclosure of WDG-V-47, or where RM-A-8, AH-FT-149, and AH-FT-150 areoperable and RM-A-8 is capable of automatic closure of WDG-V-47During Fuel Handling Building ESF Air Treatment System Operation
CHECK CHECK CALIBRATION TEST Al PPLICABILITY D W W D M N/A N/A W E(3)N/A N/A SA Q(2)N/A N/A W D W SA W CY-TM-170-300 Revision 3 Page 51 of 209 Table 3.1-2 (Cont'd)Table Notation* At all times** During waste gas holdup system operation Operability is not required when discharges are positively controlled through the closure of WDG-V-47, or where RM-A-8, AH-FT-149, and AH-FT-150 are operable and RM-A-8 is capable of automatic closure of WDG-V-47 During Fuel Handling Building ESF Air Treatment System Operation# At all times during containment purging## At all times when condenser vacuum is established
# At all times during containment purging## At all times when condenser vacuum is established
### During operation of the ventilation system (1) The CHANNEL TEST shall also demonstrate that automatic isolation of this pathway for the Auxiliary and Fuel Handling Building Ventilation System, the supply ventilation is isolated and control room alarm annunciation occurs if the following condition exists: 1. Instrument indicates measured levels above the high alarm/trip setpoint (Includes circuit failure).2. Instrument indicates a down scale failure (Alarm function only) (Includes circuit failure).3. Instrument controls moved from the operate mode (Alarm function only).(2) The CHANNEL TEST shall also demonstrate that control room alarm annunciation occurs if any of the following conditions exist: 1 Instrument indicates measured levels above the alarm setpoint. (includes circuit failure)2. Instrument indicates a down scale failure (includes circuit failure).3. Instrument controls moved from the operate mode.
### During operation of the ventilation system(1) The CHANNEL TEST shall also demonstrate that automatic isolation of this pathway forthe Auxiliary and Fuel Handling Building Ventilation System, the supply ventilation isisolated and control room alarm annunciation occurs if the following condition exists:1. Instrument indicates measured levels above the high alarm/trip setpoint (Includes circuit failure).
CY-TM-170-300 Revision 3 Page 52 of 209 Table 3.1-2 NOTATIONS (Cont'd)(3) The initial CHANNEL CALIBRATION for radioactivity measurement instrumentation shall be performed using one or more of the reference standards certified by the National Institute of Standards and Technology or using standards that have been obtained from suppliers that participate in measurement assurance activities with NIST.These standards should permit calibrating the system over its intended range of energy and measurement range. For subsequent CHANNEL CALIBRATION, sources that have been related to the initial calibration should be used. (Operating plants may substitute previously established calibration procedures for this requirement.)
: 2. Instrument indicates a down scale failure (Alarm function only) (Includes circuitfailure).
(4) The CHANNEL CALIBRATION shall include the use of standard gas samples containing a nominal: 1. One volume percent hydrogen, balance nitrogen, and 2. Four volume percent hydrogen, balance nitrogen (5) The CHANNEL CALIBRATION shall include the use of standard gas samples containing a nominal: 1. One volume percent oxygen, balance nitrogen, and 2. Four volume percent oxygen, balance nitrogen CY-TM-170-300 Revision 3 Page 53 of 209 3.2 Radiological Effluents 3.2.1 Liquid Effluents SURVEILLANCE REQUIREMENTS 3.2.1.1 Concentration 3.2.1.1.1 The radioactivity content of each batch of radioactive liquid waste shall be determined prior to release, by sampling and analysis in accordance with Table 3.2-1. The results of pre-release analyses shall be used with the calculational methods in the ODCM to assure that the concentration at the point of release is maintained within the limits of Control 2.2.1.1.3.2.1.1.2 Post-release analysis of samples composited from batch releases shall be performed in accordance with Table 3.2-1. The results of the previous post-release analysis shall be used with the calculational methods in the ODCM to assure that the concentrations at the point of release were maintained within the limits of Control 2.2.1.1.3.2.1.1.3 The radioactivity concentration of liquids discharged from continuous release points shall be determined by collection and analysis of samples in accordance with Table 3.2-1. The results of the analysis shall be used with the calculational methods of the ODCM to assure that the concentration at the point of release is maintained within the limits of Control 2.2.1.1.3.2.1.2 Dose Calculations 3.2.1.2.1 Cumulative dose contributions from liquid effluents shall be determined in accordance with the Offsite Dose Calculation Manual (ODCM) at least once a month.3.2.1.3 Liquid Waste Treatment 3.2.1.3.1 Doses due to liquid releases shall be projected at least once a month, in accordance with the ODCM.
: 3. Instrument controls moved from the operate mode (Alarm function only).(2) The CHANNEL TEST shall also demonstrate that control room alarm annunciation occurs if any of the following conditions exist:1 Instrument indicates measured levels above the alarm setpoint.  
CY-TM-170-300 Revision 3 Page 54 of 209 3.2.1.4 Liquid Holdup Tanks 3.2.1.4.1 The quantity of radioactive material contained in each of the tanks specified in Control 2.2.1.4 shall be determined to be within the limit by analyzing a representative sample of the tank's content weekly when radioactive materials are being added to the tank.
(includes circuitfailure)2. Instrument indicates a down scale failure (includes circuit failure).
CY-TM-170-300 Revision 3 Page 55 of 209 Liquid Release Type A.1 Batch Waste Release Tanks (Note Table 3.2-1 Radioactive Liquid Waste Sampling and Analysis Program Sampling Minimum Analysis Frequency Frequency Type of Acti d) P P H Each Batch Each Batch Principal GammE II-1 Dissolved and F (Gamma Emi P M Gross Each Batch Composite (Note b)P Q Sr-89 Ii Each Batch Composite (Note b) Fe Continuous W Principal Gamma (Note c) Composite (Note c) I1 Grab Sample M Dissolved and Er M (Gamma Emitter Continuous M H (Note c) Composite (Note c) Gross Continuous Q Sr-89 (Note c) Composite (Note c' Fe A.2 Continuous Releases (Note e)ivity Analysis-3 Emitters (Note f)131 Entrained Gases tters) (Note g)alpha Sr-90-55 Emitters (Note f)31Gases;) (Note g)-3 alpha Sr-90-55 I Lower Limit of Detection (LLD)(p.Ci/ml) (Note a)1 xl0-5 5 x 10-7 1 x 106 1 xl0s 1 x10-7 5 x 10-8 1 x 106 5 X10-7 I x 10 1 x 10-5 1 x 10-1 x l0i 7 5 x 108 1 x 106.1-I..... r. ..... \ ......
: 3. Instrument controls moved from the operate mode.
* CY-TM-170-300 Revision 3 Page 56 of 209 Table 3.2-1 (Cont'd)Table Notation a. The LLD is defined, for purposes of this surveillance, as the smallest concentration of radioactive material in a sample that will yield a net count above system background that will be detected with 95% probability with 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):
CY-TM-170-300 Revision 3Page 52 of 209Table 3.1-2NOTATIONS (Cont'd)(3) The initial CHANNEL CALIBRATION for radioactivity measurement instrumentation shall be performed using one or more of the reference standards certified by theNational Institute of Standards and Technology or using standards that have beenobtained from suppliers that participate in measurement assurance activities with NIST.These standards should permit calibrating the system over its intended range of energyand measurement range. For subsequent CHANNEL CALIBRATION, sources thathave been related to the initial calibration should be used. (Operating plants maysubstitute previously established calibration procedures for this requirement.)
4.66 Sb LLD =E x V x 2.22 x 106 x Y x exp (-AAt)Where: LLD is the "a priori" lower limit of detection as defined above (as microcurie per unit mass or volume)Sb is the standard deviation of the background counting rate or of the counting rate of a blank sample as appropriate (as counts per minute)E is the counting efficiency (as counts per disintegration)
(4) The CHANNEL CALIBRATION shall include the use of standard gas samplescontaining a nominal:1. One volume percent hydrogen, balance nitrogen, and2. Four volume percent hydrogen, balance nitrogen(5) The CHANNEL CALIBRATION shall include the use of standard gas samplescontaining a nominal:1. One volume percent oxygen, balance nitrogen, and2. Four volume percent oxygen, balance nitrogen CY-TM-170-300 Revision 3Page 53 of 2093.2 Radiological Effluents 3.2.1 Liquid Effluents SURVEILLANCE REQUIREMENTS 3.2.1.1 Concentration 3.2.1.1.1 The radioactivity content of each batch ofradioactive liquid waste shall be determined prior torelease, by sampling and analysis in accordance with Table 3.2-1. The results of pre-release analyses shall be used with the calculational methods in the ODCM to assure that theconcentration at the point of release is maintained within the limits of Control 2.2.1.1.3.2.1.1.2 Post-release analysis of samples composited frombatch releases shall be performed in accordance with Table 3.2-1. The results of the previouspost-release analysis shall be used with thecalculational methods in the ODCM to assure thatthe concentrations at the point of release weremaintained within the limits of Control 2.2.1.1.3.2.1.1.3 The radioactivity concentration of liquids discharged from continuous release points shall be determined by collection and analysis of samples in accordance with Table 3.2-1. The results of the analysis shallbe used with the calculational methods of theODCM to assure that the concentration at the pointof release is maintained within the limits of Control2.2.1.1.3.2.1.2 Dose Calculations 3.2.1.2.1 Cumulative dose contributions from liquid effluents shall be determined in accordance with the OffsiteDose Calculation Manual (ODCM) at least once amonth.3.2.1.3 Liquid Waste Treatment 3.2.1.3.1 Doses due to liquid releases shall be projected atleast once a month, in accordance with the ODCM.
CY-TM-170-300 Revision 3Page 54 of 2093.2.1.4 Liquid Holdup Tanks3.2.1.4.1 The quantity of radioactive material contained ineach of the tanks specified in Control 2.2.1.4 shallbe determined to be within the limit by analyzing arepresentative sample of the tank's content weeklywhen radioactive materials are being added to thetank.
CY-TM-170-300 Revision 3Page 55 of 209Liquid Release TypeA.1 Batch Waste Release Tanks (NoteTable 3.2-1Radioactive Liquid Waste Sampling and Analysis ProgramSampling Minimum AnalysisFrequency Frequency Type of Actid) P P HEach Batch Each Batch Principal GammEII-1Dissolved and F(Gamma EmiP M GrossEach Batch Composite (Note b)P Q Sr-89IiEach Batch Composite (Note b) FeContinuous W Principal Gamma(Note c) Composite (Note c) I1Grab Sample M Dissolved and ErM (Gamma EmitterContinuous M H(Note c) Composite (Note c) GrossContinuous Q Sr-89(Note c) Composite (Note c' FeA.2 Continuous Releases (Note e)ivity Analysis-3Emitters (Note f)131Entrained Gasestters) (Note g)alphaSr-90-55Emitters (Note f)31 Gases;) (Note g)-3alphaSr-90-55ILower Limit ofDetection (LLD)(p.Ci/ml)  
(Note a)1 xl0-55 x 10-71 x 1061 xl0s1 x10-75 x 10-81 x 1065 X10-7I x 101 x 10-51 x 10-1 x l0i75 x 1081 x 106.1-I..... r. ..... \ ......
* CY-TM-170-300 Revision 3Page 56 of 209Table 3.2-1 (Cont'd)Table Notationa. The LLD is defined, for purposes of this surveillance, as the smallestconcentration of radioactive material in a sample that will yield a net count abovesystem background that will be detected with 95% probability with 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):
4.66 SbLLD =E x V x 2.22 x 106 x Y x exp (-AAt)Where:LLD is the "a priori" lower limit of detection as defined above (as microcurie perunit mass or volume)Sb is the standard deviation of the background counting rate or of the countingrate of a blank sample as appropriate (as counts per minute)E is the counting efficiency (as counts per disintegration)
V is the sample size (in units of mass or volume)2.22 E6 is the number of disintegrations per minute per microcurie Y is the fractional radiochemical yield (when applicable)
V is the sample size (in units of mass or volume)2.22 E6 is the number of disintegrations per minute per microcurie Y is the fractional radiochemical yield (when applicable)
X is the radioactive decay constant for the particular radionuclide, andAt is the elapsed time between midpoint of sample collection and time of countingTypical values of E, V, Y and At shall be used in the calculation It should be recognized that the LLD is defined as an "a priori" (before the fact)limit representing the capability of a measurement system and not as an "aposteriori" (after the fact) limit for a particular measurement
X is the radioactive decay constant for the particular radionuclide, and At is the elapsed time between midpoint of sample collection and time of counting Typical values of E, V, Y and At shall be used in the calculation It should be recognized that the LLD is defined as an "a priori" (before the fact)limit representing the capability of a measurement system and not as an "a posteriori" (after the fact) limit for a particular measurement
: b. A composite sample is one in which the quantity of liquid sampled is proportional to the quantity of liquid waste discharged and in which the method of samplingemployed results in a specimen which is representative of the liquids released CY-TM-1 70-300Revision 3Page 57 of 209Table 3.2-1 Notations (Cont'd)c. To be representative of the quantities and concentrations of radioactive materials in liquid effluent, samples shall be collected continuously in proportion to the rateof flow of the effluent stream. Prior to analyses, all samples taken for thecomposite shall be thoroughly mixed in order for the composite sample to berepresentative of the effluent released. A batch release is the discharge of liquid wastes of a discrete volume. Prior tosampling for analyses, each batch shall be isolated, and be thoroughly mixed, bya method described in the ODCM, to assure representative sampling.
: b. A composite sample is one in which the quantity of liquid sampled is proportional to the quantity of liquid waste discharged and in which the method of sampling employed results in a specimen which is representative of the liquids released CY-TM-1 70-300 Revision 3 Page 57 of 209 Table 3.2-1 Notations (Cont'd)c. To be representative of the quantities and concentrations of radioactive materials in liquid effluent, samples shall be collected continuously in proportion to the rate of flow of the effluent stream. Prior to analyses, all samples taken for the composite shall be thoroughly mixed in order for the composite sample to be representative of the effluent release d. A batch release is the discharge of liquid wastes of a discrete volume. Prior to sampling for analyses, each batch shall be isolated, and be thoroughly mixed, by a method described in the ODCM, to assure representative sampling.e. A continuous release is the discharge of liquid wastes of a non- discrete volume;e.g., from a volume or system that has an input flow during the continuous release.f. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:
: e. A continuous release is the discharge of liquid wastes of a non- discrete volume;e.g., from a volume or system that has an input flow during the continuous release.f. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:
Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99, Cs-134, Cs-137, Ce-141, and Ce-144. This list does not mean that only these nuclides are to be considered.
Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99,Cs-134, Cs-137, Ce-141, and Ce-144. This list does not mean that only thesenuclides are to be considered.
Other gamma peaks that are identifiable, together with those of the above nuclides, shall also be analyzed and reported in the Annual Radioactive Effluent Release Report pursuant to TS 6.9.4.g. The gamma emitters for which the LLD specification applies exclusively are the following radionuclides:
Other gamma peaks that are identifiable, togetherwith those of the above nuclides, shall also be analyzed and reported in theAnnual Radioactive Effluent Release Report pursuant to TS 6.9.4.g. The gamma emitters for which the LLD specification applies exclusively are thefollowing radionuclides:
Kr-87, Kr-88, Xe-133, Xe-133m, and Xe-135. This list does not mean that only these nuclides are to be considered.
Kr-87, Kr-88, Xe-133, Xe-133m, and Xe-135. This listdoes not mean that only these nuclides are to be considered.
Other gamma peaks that are identifiable, together with those of the above nuclides, shall also be analyzed and reported in the Annual Effluent Release Report pursuant to T.S.6.9.4.
Other gammapeaks that are identifiable, together with those of the above nuclides, shall alsobe analyzed and reported in the Annual Effluent Release Report pursuant to T.S.6.9.4.
CY-TM-1 70-300 Revision 3 Page 58 of 209 3.2.2 Gaseous Effluents SURVEILLANCE REQUIREMENTS 3.2.2.1 Dose Rates 3.2.2.1.1 The dose rate due to noble gases in gaseous effluents shall be determined to be within the limits of Control 2.2.2.1 .a in accordance with the methods and procedures of the ODCM.3.2.2.1.2 The dose rate of radioactive materials, other than noble gases, in gaseous effluents shall be determined to be within the limits of Control 2.2.2.1.b in accordance with methods and procedures of the ODCM by obtaining representative samples and performing analyses in accordance with the sampling and analysis program, specified in Table 3.2-2.3.2.2.2 Dose, Noble Gas 3.2.2.2.1 Cumulative dose contributions from noble gas effluents for the current calendar quarter and current calendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM) monthly.3.2.2.3 Dose, Iodine-131, Iodine-1 33, Tritium, and Radionuclides in Particulate Form 3.2.2.3.1 Cumulative dose contributions from Iodine-1 31, Iodine-133, Tritium, and radionuclides in particulate form with half lives greater than 8 days for the current calendar quarter and current calendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM)monthly.3.2.2.4 Gaseous Waste Treatment 3.2.2.4.1 Doses due to gaseous releases from the unit shall be projected monthly in accordance with the ODCM.
CY-TM-1 70-300Revision 3Page 58 of 2093.2.2 Gaseous Effluents SURVEILLANCE REQUIREMENTS 3.2.2.1 Dose Rates3.2.2.1.1 The dose rate due to noble gases in gaseouseffluents shall be determined to be within the limitsof Control 2.2.2.1 .a in accordance with the methodsand procedures of the ODCM.3.2.2.1.2 The dose rate of radioactive materials, other thannoble gases, in gaseous effluents shall bedetermined to be within the limits of Control2.2.2.1.b in accordance with methods andprocedures of the ODCM by obtaining representative samples and performing analyses inaccordance with the sampling and analysisprogram, specified in Table 3.2-2.3.2.2.2 Dose, Noble Gas3.2.2.2.1 Cumulative dose contributions from noble gaseffluents for the current calendar quarter and currentcalendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL(ODCM) monthly.3.2.2.3 Dose, Iodine-131, Iodine-1 33, Tritium, and Radionuclides inParticulate Form3.2.2.3.1 Cumulative dose contributions from Iodine-1 31,Iodine-133,  
CY-TM-170-300 Revision 3 Page 59 of 209 3.2.2.5 Explosive Gas Mixture 3.2.2.5.1 The concentrations of hydrogen and oxygen in the waste gas holdup system shall be determined to be within the limits of Control 2.2.2.5 by monitoring the waste gases in the Waste Gas Holdup System with the hydrogen and oxygen monitors covered in Table 2.1-2 of Control 2.1.2.3.2.2.6 Waste Gas Decay Tank 3.2.2.6.1 The concentration of radioactivity contained in the vent header shall be determined weekly. If the concentration of the vent header exceeds 10.7 gCi/cc, daily samples shall be taken of each waste gas decay tank being added to, to determine if the tank(s) is less than or equal to 8800 Ci/tank.
: Tritium, and radionuclides in particulate form with half lives greater than 8 days for thecurrent calendar quarter and current calendar yearshall be determined in accordance with theOFFSITE DOSE CALCULATION MANUAL (ODCM)monthly.3.2.2.4 Gaseous Waste Treatment 3.2.2.4.1 Doses due to gaseous releases from the unit shallbe projected monthly in accordance with the ODCM.
CY-TM-170-300 Revision 3 Page 60 of 209 Table 3.2-2 Radioactive Gaseous Waste Sampling and Analysis Program Minimum Lower Limit of Sampling Analysis Type of Activity Detection (LLD)Gaseous Release Type Frequency Frequency Analysis piCi/ml) (Note a)P EhaP Principal Gamma 1 A. Waste Gas Decay Tank Grab Sample Each Tank Emitters (Note g)B. Containment Purge H-3 1 x 10-6 P (Note b)Each P (Note b) Each Principal Gamma Purge Grab Sample Purge Emitters (Note g) 1 X 10.C. Auxiliary and Fuel Handling Building H-3 1 x10.6 Air Treatment System M (Notes c, e) Grab Sample M Principal Gamma 1 Emitters (Note g) 1 x 10 D. Fuel Handling Building ESF Air Treatment System M (during System M (during H-3 1 x 10-6 Operation)
CY-TM-170-300 Revision 3Page 59 of 2093.2.2.5 Explosive Gas Mixture3.2.2.5.1 The concentrations of hydrogen and oxygen in thewaste gas holdup system shall be determined to bewithin the limits of Control 2.2.2.5 by monitoring thewaste gases in the Waste Gas Holdup System withthe hydrogen and oxygen monitors covered in Table2.1-2 of Control 2.1.2.3.2.2.6 Waste Gas Decay Tank3.2.2.6.1 The concentration of radioactivity contained in thevent header shall be determined weekly. If theconcentration of the vent header exceeds10.7 gCi/cc, daily samples shall be taken of eachwaste gas decay tank being added to, to determine if the tank(s) is less than or equal to 8800 Ci/tank.
System Principal Gamma Grab Sample Operation)
CY-TM-170-300 Revision 3Page 60 of 209Table 3.2-2Radioactive Gaseous Waste Sampling and Analysis ProgramMinimum Lower Limit ofSampling Analysis Type of Activity Detection (LLD)Gaseous Release Type Frequency Frequency Analysis piCi/ml)  
Emitters (Note g) 1 x 10-4 Ex as Nt )H-3 1 x10-6 E. Condenser Vacuum Pumps Exhaust (Note h) M (Note h) M Principal Gamma Grab Sample (Note h) Emitters (Note g) 1 x 10-4 F. Chemical Cleaning Building Air Treatment System MH-3 1 x 1r0i M (Notel1) M Principal Gamma Grab Sample Emitters (Note g) 1x 10-4 G. Waste Handling and Packaging Facility See Section I See Section I See Section I See Section I Air Treatment System of this table of this table of this table of this table H. Respirator and Laundry Maintenance Facility See Section I See Section I See Section I See Section I Air Treatment System of this table of this table of this table , of this table CY-TM-170-300 Revision 3 Page 61 of 209 Table 3.2-2 (Cont'd)Radioactive Gaseous Waste Sampling and Analysis Program Lower Limit of I Sampling Minimum Analysis Type of Activity Detection (LLD)Gaseous Release Type Frequency Frequency Analysis (pCi/ml) (Note a)All Release Types as Listed Above in B, C, D, F, G, and H (During System Operation)
(Note a)PEhaP Principal Gamma 1A. Waste Gas Decay Tank Grab Sample Each Tank Emitters (Note g)B. Containment Purge H-3 1 x 10-6P (Note b)Each P (Note b) Each Principal GammaPurge Grab Sample Purge Emitters (Note g) 1 X 10.C. Auxiliary and Fuel Handling Building H-3 1 x10.6Air Treatment System M (Notes c, e) GrabSample M Principal Gamma 1Emitters (Note g) 1 x 10D. Fuel Handling Building ESF Air Treatment System M (during System M (during H-3 1 x 10-6Operation)
Continuous W (Note d) 1-131 1 X 10-12 (Note f) Charcoal Sample : 1 0 (Note i) ___Principal Gamma Continuous W (Note d) Emitters (Note g) 1x10 1 1 (Note f) Particulate (1-131, Others)Q Continuous Composite Gross Alpha 1 x .10"11 (Note f) Particulate Sample Q Continuous Composite Sr-89, Sr-90 1 x 10-11 (Note f) Particulate Sample Continuous Noble Gas 1 X, (Note f) Beta or Gamma Noble Gases , 1 x 10.6 J, Condenser Vent Stack Continuous Iodine Continuous W (Note d) 1-131 1 x 10-12 Sampler (Note j) (Note k) Charcoal Sample CY-TM-1 70-300 Revision 3 Page 62 of 209 Table 3.2-2 (Cont'd)Table Notation a. The LLD is defined, for purposes of this surveillance, as the smallest concentration of radioactive material in a sample that will yield a net count above system background that will be detected with 95% probability with 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):
System Principal GammaGrab Sample Operation)
4.66Sb LLD =E xV x2.22 x 106 x Y xexp(-kAt)
Emitters (Note g) 1 x 10-4Ex as Nt )H-3 1 x10-6E. Condenser Vacuum Pumps Exhaust (Note h) M (Note h) M Principal GammaGrab Sample (Note h) Emitters (Note g) 1 x 10-4F. Chemical Cleaning Building Air Treatment System MH-3 1 x 1r0iM (Notel1)
Where: LLD is the "a priori" lower limit of detection as defined above (as microcurie per unit mass or volume)Sb is the standard deviation of the background counting rate or of the counting rate of a blank sample as appropriate (as counts per minute)E is the counting efficiency (as counts per disintegration)
M Principal GammaGrab Sample Emitters (Note g) 1x 10-4G. Waste Handling and Packaging Facility See Section I See Section I See Section I See Section IAir Treatment System of this table of this table of this table of this tableH. Respirator and Laundry Maintenance Facility See Section I See Section I See Section I See Section IAir Treatment System of this table of this table of this table , of this table CY-TM-170-300 Revision 3Page 61 of 209Table 3.2-2 (Cont'd)Radioactive Gaseous Waste Sampling and Analysis ProgramLower Limit ofI Sampling Minimum Analysis Type of Activity Detection (LLD)Gaseous Release Type Frequency Frequency Analysis (pCi/ml)  
(Note a)All Release Types as Listed Above in B, C, D, F, G,and H (During System Operation)
Continuous W (Note d) 1-131 1 X 10-12(Note f) Charcoal Sample : 1 0(Note i) ___Principal GammaContinuous W (Note d) Emitters (Note g) 1x1011(Note f) Particulate (1-131, Others)QContinuous Composite Gross Alpha 1 x .10"11(Note f) Particulate SampleQContinuous Composite Sr-89, Sr-90 1 x 10-11(Note f) Particulate SampleContinuous Noble Gas 1 X,(Note f) Beta or Gamma Noble Gases , 1 x 10.6J, Condenser Vent Stack Continuous Iodine Continuous W (Note d) 1-131 1 x 10-12Sampler (Note j) (Note k) Charcoal Sample CY-TM-1 70-300Revision 3Page 62 of 209Table 3.2-2 (Cont'd)Table Notationa. The LLD is defined, for purposes of this surveillance, as the smallestconcentration of radioactive material in a sample that will yield a net count abovesystem background that will be detected with 95% probability with 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):
4.66SbLLD =E xV x2.22 x 106 x Y xexp(-kAt)
Where: LLD is the "a priori" lower limit of detection as defined above (as microcurie perunit mass or volume)Sb is the standard deviation of the background counting rate or of the countingrate of a blank sample as appropriate (as counts per minute)E is the counting efficiency (as counts per disintegration)
V is the sample size (in units of mass or volume)2.22 E6 is the number of disintegrations per minute per microcurie Y is the fractional radiochemical yield (when applicable)
V is the sample size (in units of mass or volume)2.22 E6 is the number of disintegrations per minute per microcurie Y is the fractional radiochemical yield (when applicable)
X is the radioactive decay constant for the particular radionuclide, andAt is the elapsed time between midpoint of sample collection and time ofcounting.
X is the radioactive decay constant for the particular radionuclide, and At is the elapsed time between midpoint of sample collection and time of counting.Typical values of E, V, Y and At shall be used in the calculation.
Typical values of E, V, Y and At shall be used in the calculation.
It should be recognized that the LLD is defined as an "a priori" (before the fact)limit representing the capability of a measurement system and not as an "a posteriori" (after the fact) limit for a particular measurement.
It should be recognized that the LLD is defined as an "a priori" (before the fact)limit representing the capability of a measurement system and not as an "aposteriori" (after the fact) limit for a particular measurement.
: b. Sampling and analysis shall also be performed following shutdown, startup, or THERMAL POWER change exceeding 15 percent of RATED THERMAL POWER within one hour, unless (1) analysis shows that the DOSE EQUIVALENT 1-131 concentration in the primary coolant has not increased more than a factor of 3; and (2) the noble gas activity monitor shows that effluent activity has not increased by more than a factor of 3.c. Tritium grab samples from the spent fuel pool area shall be taken at least once per 24 hours when the refueling canal is flooded.
: b. Sampling and analysis shall also be performed following  
CY-TM-170-300 Revision 3 Page 63 of 209 Table 3.2-2 Notations (Cont'd)d. Charcoal cartridges and particulate filters shall be changed at least once per 7 days and analyses shall be completed within 48 hours after changing (or after removal from sampler).e. Tritium grab samples shall be taken weekly from the spent fuel pool area whenever spent fuel is in the spent fuel pool.f. The ratio of the sample flow rate to the sampled stream flow rate shall be known for the time period covered by each dose or dose rate calculation made in accordance with Controls 2.2.2.1, 2.2.2.2, and 2.2.2.3.g. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:
: shutdown, startup, orTHERMAL POWER change exceeding 15 percent of RATED THERMALPOWER within one hour, unless (1) analysis shows that the DOSEEQUIVALENT 1-131 concentration in the primary coolant has not increased morethan a factor of 3; and (2) the noble gas activity monitor shows that effluentactivity has not increased by more than a factor of 3.c. Tritium grab samples from the spent fuel pool area shall be taken at least onceper 24 hours when the refueling canal is flooded.
Kr-87, Kr-88, Xe-1 33, Xe-1 33m, Xe-1 35 and Xe-1 38 for gaseous emissions and Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99, Cs-1 37, Ce-141 and Ce-144 for particulate emissions.
CY-TM-170-300 Revision 3Page 63 of 209Table 3.2-2 Notations (Cont'd)d. Charcoal cartridges and particulate filters shall be changed at least once per 7days and analyses shall be completed within 48 hours after changing (or afterremoval from sampler).
This list does not mean that only these nuclides are to be considered.
: e. Tritium grab samples shall be taken weekly from the spent fuel pool areawhenever spent fuel is in the spent fuel pool.f. The ratio of the sample flow rate to the sampled stream flow rate shall be knownfor the time period covered by each dose or dose rate calculation made inaccordance with Controls 2.2.2.1, 2.2.2.2, and 2.2.2.3.g. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:
Other gamma peaks that are identifiable, together with those of the above nuclides, shall also be analyzed and reported in the Annual Radioactive Effluent Release Report pursuant to TS 6.9.4.h. Applicable only when condenser vacuum is established.
Kr-87, Kr-88, Xe-1 33, Xe-1 33m, Xe-1 35 andXe-1 38 for gaseous emissions and Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99,Cs-1 37, Ce-141 and Ce-144 for particulate emissions.
Sampling and analysis shall also be performed following shutdown, startup, or a THERMAL POWER change exceeding 15 percent of RATED THERMAL POWER within one hour unless (1) analysis shows that the DOSE EQUIVALENT 1-131 concentration in the primary coolant has not increased more than a factor of 3; and (2) the noble gas activity monitor shows that effluent activity has not increased by more than a factor of 3.Gross Alpha, Sr-89, and Sr-90 analyses do not apply to the Fuel Handling Building ESF Air Treatment System.j. If the Condenser Vent Stack Continuous Iodine Sampler is unavailable, then alternate sampling equipment will be placed in service within 48 hours or a report will be prepared, and submitted within 30 days from the time the sampler is found or made inoperable, which identifies (a) the cause of the inoperability, (b) the action taken to restore representative sampling capability, (c) the action taken to prevent recurrence, and (d) quantification of the release via the pathway during the period and comparison to the limits prescribed by Control 2.2.2.1.b.
This list does not meanthat only these nuclides are to be considered.
Other gamma peaks that areidentifiable, together with those of the above nuclides, shall also be analyzed andreported in the Annual Radioactive Effluent Release Report pursuant to TS 6.9.4.h. Applicable only when condenser vacuum is established.
Sampling and analysisshall also be performed following  
: shutdown, startup, or a THERMAL POWERchange exceeding 15 percent of RATED THERMAL POWER within one hourunless (1) analysis shows that the DOSE EQUIVALENT 1-131 concentration inthe primary coolant has not increased more than a factor of 3; and (2) the noblegas activity monitor shows that effluent activity has not increased by more than afactor of 3.Gross Alpha, Sr-89, and Sr-90 analyses do not apply to the Fuel HandlingBuilding ESF Air Treatment System.j. If the Condenser Vent Stack Continuous Iodine Sampler is unavailable, thenalternate sampling equipment will be placed in service within 48 hours or a reportwill be prepared, and submitted within 30 days from the time the sampler is foundor made inoperable, which identifies (a) the cause of the inoperability, (b) theaction taken to restore representative sampling capability, (c) the action taken toprevent recurrence, and (d) quantification of the release via the pathway duringthe period and comparison to the limits prescribed by Control 2.2.2.1.b.
: k. Applicable only when condenser vacuum is established.
: k. Applicable only when condenser vacuum is established.
: 1. Applicable when liquid radwaste is moved or processed within the facility.
: 1. Applicable when liquid radwaste is moved or processed within the facility.m. Iodine samples only required in the Chemical Cleaning Building when TMI-1 liquid radwaste is stored or processed in the facility.
: m. Iodine samples only required in the Chemical Cleaning Building when TMI-1liquid radwaste is stored or processed in the facility.
CY-TM-1 70-300 Revision 3 Page 64 of 209 3.2.3 Total Radioactive Effluents 3.2.3.1 Dose Calculation 3.2.3.1.1 Cumulative annual dose contributions from liquid and gaseous effluents shall be determined in accordance with Surveillances 3.2.1.2.1, 3.2.2.2.1, and 3.2.2.3.1, including direct radiation contributions from the Unit and from outside storage tanks, and in accordance with the methodology contained in the ODCM.
CY-TM-1 70-300Revision 3Page 64 of 2093.2.3 Total Radioactive Effluents 3.2.3.1 Dose Calculation 3.2.3.1.1 Cumulative annual dose contributions from liquid andgaseous effluents shall be determined in accordance withSurveillances 3.2.1.2.1, 3.2.2.2.1, and 3.2.2.3.1, including direct radiation contributions from the Unit and fromoutside storage tanks, and in accordance with themethodology contained in the ODCM.
CY-TM-170-300 Revision 3 Page 65 of 209 4.0 PART I REFERENCES 4.1 Title 10, Code of Federal Regulations, "Energy" 4.2 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routing Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I, "Revision 1, October 1977 4.3 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-50 4.4 TMI-1 FSAR CY-TM-1 70-300 Revision 3 Page 66 of 209 PART II TMI-2 RADIOLOGICAL EFFLUENT CONTROLS CY-TM-1 70-300 Revision 3 Page 67 of 209 PART II Definitions
CY-TM-170-300 Revision 3Page 65 of 2094.0 PART I REFERENCES 4.1 Title 10, Code of Federal Regulations, "Energy"4.2 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from RoutingReleases of Reactor Effluents for the Purpose of Evaluating Compliance with 10CFR Part 50, Appendix I, "Revision 1, October 19774.3 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-504.4 TMI-1 FSAR CY-TM-1 70-300Revision 3Page 66 of 209PART IITMI-2 RADIOLOGICAL EFFLUENT CONTROLS CY-TM-1 70-300Revision 3Page 67 of 209PART IIDefinitions


==1.0 DEFINITIONS==
==1.0 DEFINITIONS==
DEFINED TERMS1.1 The DEFINED TERMS of this section appear in capitalized type and areapplicable throughout Part II of the ODCM.PDMS1.2 Post-Defueling Monitored Storage (PDMS) is that condition where TMI-2defueling has been completed, the core debris removed from the reactor duringthe clean-up period has been shipped off-site, and the facility has been placed ina stable, safe, and secure condition.
DEFINED TERMS 1.1 The DEFINED TERMS of this section appear in capitalized type and are applicable throughout Part II of the ODCM.PDMS 1.2 Post-Defueling Monitored Storage (PDMS) is that condition where TMI-2 defueling has been completed, the core debris removed from the reactor during the clean-up period has been shipped off-site, and the facility has been placed in a stable, safe, and secure condition.
ACTION1.3 ACTION shall be those additional requirements specified as corollary statements to each control and shall be part of the controls.
ACTION 1.3 ACTION shall be those additional requirements specified as corollary statements to each control and shall be part of the controls.OPERABLE -OPERABILITY 1.4 A system, subsystem, train, component or device shall be OPERABLE or have OPERABILITY when it is capable of performing its specified function(s).
OPERABLE  
Implicit in this definition shall be the assumption that all necessary attendant instrumentation, controls, normal and emergency electrical power sources, cooling or seal water, lubrication or other auxiliary equipment, that are required for the system, subsystem, train, component or device to perform its function(s), are also capable of performing their related support function(s).
-OPERABILITY 1.4 A system, subsystem, train, component or device shall be OPERABLE or haveOPERABILITY when it is capable of performing its specified function(s).
CHANNEL CALIBRATION 1.5 A CHANNEL CALIBRATION shall be the adjustment, as necessary, of the channel output such that it responds with necessary range and accuracy to known values of the parameter, which the channel monitors.
Implicitin this definition shall be the assumption that all necessary attendant instrumentation,  
The CHANNEL CALIBRATION shall encompass the entire channel including the sensor and alarm and/or trip functions, and shall include the CHANNEL FUNCTIONAL TEST. CHANNEL CALIBRATION may be performed by any series of sequential, overlapping or total channel steps such that the entire channel is calibrated.
: controls, normal and emergency electrical power sources,cooling or seal water, lubrication or other auxiliary equipment, that are requiredfor the system, subsystem, train, component or device to perform its function(s),
CY-TM-1 70-300 Revision 3 Page 68 of 209 CHANNEL CHECK 1.6 A CHANNEL CHECK shall be the qualitative assessment of channel behavior during operation by observation.
are also capable of performing their related support function(s).
This determination shall include, where possible, comparison of the channel indication and/or status with other indications and/or status derived from independent instrument channels measuring the same parameter.
CHANNEL CALIBRATION 1.5 A CHANNEL CALIBRATION shall be the adjustment, as necessary, of thechannel output such that it responds with necessary range and accuracy toknown values of the parameter, which the channel monitors.
CHANNEL FUNCTIONAL TEST 1.7 A CHANNEL FUNCTIONAL TEST shall be: a. Analog channels -the injection of a simulated signal into the channel as close to the primary sensor as practicable to verify OPERABILITY including alarm and/or trip functions.
The CHANNELCALIBRATION shall encompass the entire channel including the sensor andalarm and/or trip functions, and shall include the CHANNEL FUNCTIONAL TEST. CHANNEL CALIBRATION may be performed by any series of sequential, overlapping or total channel steps such that the entire channel is calibrated.
: b. Bistable channels -the injection of a simulated signal into the channel sensor to verify OPERABILITY including alarm and/or trip functions.
CY-TM-1 70-300Revision 3Page 68 of 209CHANNEL CHECK1.6 A CHANNEL CHECK shall be the qualitative assessment of channel behaviorduring operation by observation.
SOURCE CHECK 1.8 A SOURCE CHECK shall be the qualitative assessment of channel response when the channel sensor is exposed to a radioactive source.COMPOSITE SAMPLE 1.9 A COMPOSITE SAMPLE is a combination of individual samples obtained at regular intervals over a time period. Either the volume of each individual sample is proportional to the flow rate discharge at the time of sampling or the number of equal volume samples is proportional to the time period used to produce the composite.
This determination shall include, wherepossible, comparison of the channel indication and/or status with otherindications and/or status derived from independent instrument channelsmeasuring the same parameter.
GRAB SAMPLE 1.10 A GRAB SAMPLE is an individual sample collected in less than fifteen minutes.BATCH RELEASE 1.11 A BATCH RELEASE is the discharge of fluid waste of a discrete volume.CONTINUOUS RELEASE 1.12 A CONTINUOUS RELEASE is the discharge of fluid waste of a non-discrete volume, e.g., from a volume or system that has an input flow during the CONTINUOUS RELEASE.
CHANNEL FUNCTIONAL TEST1.7 A CHANNEL FUNCTIONAL TEST shall be:a. Analog channels  
CY-TM-170-300 Revision 3 Page 69 of 209 SITE BOUNDARY 1.13 The SITE BOUNDARY used as the basis for the limits on the release of gaseous effluents is as defined in Section 2.1.2.2 and shown on Figure 2.1-3 of the TMI-1 FSAR. This boundary line includes portions of the Susquehanna River surface between the east bank of the river and Three Mile Island and between Three Mile Island and Shelley Island.The SITE BOUNDARY used as the basis for the limits on the release of liquid effluents is as shown in Figure 1.1 in Part I of this ODCM.FREQUENCY NOTATION 1.14 The FREQUENCY NOTATION specified for the performance of Surveillance Requirements shall correspond to the intervals defined in Table 1.1. All Surveillance Requirements shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% of the surveillance interval.
-the injection of a simulated signal into the channel asclose to the primary sensor as practicable to verify OPERABILITY including alarm and/or trip functions.
CY-TM-170-300 Revision 3 Page 70 of 209 TABLE 1.1 Frequency Notation NOTATION FREQUENCY S (Shiftly)D (Daily)W (Weekly)M (Monthly)Q (Quarterly)
: b. Bistable channels  
-the injection of a simulated signal into the channelsensor to verify OPERABILITY including alarm and/or trip functions.
SOURCE CHECK1.8 A SOURCE CHECK shall be the qualitative assessment of channel responsewhen the channel sensor is exposed to a radioactive source.COMPOSITE SAMPLE1.9 A COMPOSITE SAMPLE is a combination of individual samples obtained atregular intervals over a time period. Either the volume of each individual sampleis proportional to the flow rate discharge at the time of sampling or the number ofequal volume samples is proportional to the time period used to produce thecomposite.
GRAB SAMPLE1.10 A GRAB SAMPLE is an individual sample collected in less than fifteen minutes.BATCH RELEASE1.11 A BATCH RELEASE is the discharge of fluid waste of a discrete volume.CONTINUOUS RELEASE1.12 A CONTINUOUS RELEASE is the discharge of fluid waste of a non-discrete volume, e.g., from a volume or system that has an input flow during theCONTINUOUS RELEASE.
CY-TM-170-300 Revision 3Page 69 of 209SITE BOUNDARY1.13 The SITE BOUNDARY used as the basis for the limits on the release of gaseouseffluents is as defined in Section 2.1.2.2 and shown on Figure 2.1-3 of the TMI-1FSAR. This boundary line includes portions of the Susquehanna River surfacebetween the east bank of the river and Three Mile Island and between Three MileIsland and Shelley Island.The SITE BOUNDARY used as the basis for the limits on the release of liquideffluents is as shown in Figure 1.1 in Part I of this ODCM.FREQUENCY NOTATION1.14 The FREQUENCY NOTATION specified for the performance of Surveillance Requirements shall correspond to the intervals defined in Table 1.1. AllSurveillance Requirements shall be performed within the specified time intervalwith a maximum allowable extension not to exceed 25% of the surveillance interval.
CY-TM-170-300 Revision 3Page 70 of 209TABLE 1.1Frequency NotationNOTATIONFREQUENCY S (Shiftly)
D (Daily)W (Weekly)M (Monthly)
Q (Quarterly)
SA (Semi-Annually)
SA (Semi-Annually)
A (Annually)
A (Annually)
EN.A.At least once per 12 hoursAt least once per 24 hoursAt least once per 7 daysAt least once per 31 daysAt least once per 92 daysAt least once per 184 daysAt least once per 12 monthsAt least once per 18 monthsNot applicable Completed prior to each releaseP CY-TM-170-300 Revision 3Page 71 of 2092.0 CONTROLS AND BASES2.0.1 Controls and ACTION requirements shall be applicable during theconditions specified for each control.2.0.2 Adherence to the requirements of the Control and/or associated ACTION within the specified time interval shall constitute compliance with the control.
E N.A.At least once per 12 hours At least once per 24 hours At least once per 7 days At least once per 31 days At least once per 92 days At least once per 184 days At least once per 12 months At least once per 18 months Not applicable Completed prior to each release P CY-TM-170-300 Revision 3 Page 71 of 209 2.0 CONTROLS AND BASES 2.0.1 Controls and ACTION requirements shall be applicable during the conditions specified for each control.2.0.2 Adherence to the requirements of the Control and/or associated ACTION within the specified time interval shall constitute compliance with the control. In the event the Control is restored prior to expiration to the specified time interval, completion of the ACTION statement is not required.2.0.3 In the event the Control and associated ACTION requirements cannot be satisfied because of circumstances in excess of those addressed in the Control, initiate appropriate actions to rectify the problem to the extent possible under the circumstances, and submit a special report to the Commission pursuant to TMI-2 PDMS Technical Specification (Tech.Spec.) Section 6.8.2 within 30 days, unless otherwise specified.
In the event the Control is restored prior to expiration tothe specified time interval, completion of the ACTION statement is notrequired.
2.1 Radioactive Effluent Instrumentation 2.1.1 Radioactive Liquid Effluent Instrumentation Radioactive Liquid Effluent Instrumentation is common between TMI-1 and TMI-2. Controls, applicability, and actions are specified in ODCM Part I, Control 2.1.1 2.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation CONTROL: The radioactive gaseous process and effluent monitoring instrumentation channels shown in Table 2.1-2 shall be OPERABLE with their alarm/trip setpoints set to ensure that the limits of Control 2.2.2.1 are not exceeded.
2.0.3 In the event the Control and associated ACTION requirements cannotbe satisfied because of circumstances in excess of those addressed inthe Control, initiate appropriate actions to rectify the problem to theextent possible under the circumstances, and submit a special report tothe Commission pursuant to TMI-2 PDMS Technical Specification (Tech.Spec.) Section 6.8.2 within 30 days, unless otherwise specified.
The alarm/trip setpoints of these channels shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:
2.1 Radioactive Effluent Instrumentation 2.1.1 Radioactive Liquid Effluent Instrumentation Radioactive Liquid Effluent Instrumentation is common between TMI-1and TMI-2. Controls, applicability, and actions are specified in ODCMPart I, Control 2.1.12.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation CONTROL:The radioactive gaseous process and effluent monitoring instrumentation channels shown in Table 2.1-2 shall be OPERABLE withtheir alarm/trip setpoints set to ensure that the limits of Control 2.2.2.1are not exceeded.
As shown in Table 2.1-2 ACTION: a. With a radioactive gaseous process or effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required by the above control, immediately suspend the release of radioactive effluent monitored by the affected channel or declare the channel inoperable.
The alarm/trip setpoints of these channels shall bedetermined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:
CY-TM-1 70-300 Revision 3 Page 72 of 209 b. With less than the minimum number of radioactive gaseous process or effluent monitoring instrumentation channels OPERABLE, take the ACTION shown in Table 2.1-2. Exert best efforts to return the instrumentation to OPERABLE status within 30 days and, if unsuccessful, explain in the next Annual Effluent Release Report why the inoperability was not corrected in a timely manner.BASES The radioactive gaseous effluent instrumentation is provided to monitor and control, as applicable, the releases of radioactive materials in gaseous effluent during actual or potential releases.
As shown in Table 2.1-2ACTION:a. With a radioactive gaseous process or effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required by the above control, immediately suspend therelease of radioactive effluent monitored by the affectedchannel or declare the channel inoperable.
The alarm/trip setpoints for these instruments shall be calculated in accordance with NRC approved methods in the ODCM to provide reasonable assurance that the annual releases are within the limits specified in 10 CFR 20.1301.
CY-TM-1 70-300Revision 3Page 72 of 209b. With less than the minimum number of radioactive gaseousprocess or effluent monitoring instrumentation channelsOPERABLE, take the ACTION shown in Table 2.1-2. Exertbest efforts to return the instrumentation to OPERABLE statuswithin 30 days and, if unsuccessful, explain in the next AnnualEffluent Release Report why the inoperability was notcorrected in a timely manner.BASESThe radioactive gaseous effluent instrumentation is provided to monitorand control, as applicable, the releases of radioactive materials ingaseous effluent during actual or potential releases.
CY-TM-170-300 Revision 3 Page 73 of 209 Table 2.1-2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUM CHANNELS INSTRUMENT OPERABLE APPLICABILITY ACTION 1. Containment Purge Monitoring System a. Noble Gas Activity Monitor (2HP-R-225) 1 NOTE 1 NOTE 2 b. Particulate Monitor (2HP-R-225) 1 NOTE 1 NOTE 2 c. Effluent System Flow Rate Measuring Device (2AH-FR-5907 Point 1) 1 NOTE 1 NOTE 3 2. Station Ventilation System a. Noble Gas Activity Monitor (2HP-R-219) or (2HP-R-219A) 1 NOTE 1 NOTE 2 b. Particulate Monitor (2HP-R-219) or (2HP-R-219A) 1 NOTE 1 NOTE 2 c. Effluent System Flow Rate Monitoring Device (2AH-FR-5907 Point 6) 1 NOTE 1 NOTE 3 NOTES: 1. During operation of the monitored system.2. With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, secure Reactor Building Purge if in progress.3. With flow rate monitoring instrumentation out of service, flow rates from the Auxiliary (2AH-FR-5907 Point 2), Fuel Handling (2AH-FR-5907 Point 4), Soiled Exhaust System (2AH-FR-5907 Point 5), and Reactor Buildings (2AH-FR-5907 Point 1) may be summed individually.
The alarm/trip setpoints for these instruments shall be calculated in accordance withNRC approved methods in the ODCM to provide reasonable assurance that the annual releases are within the limits specified in 10 CFR20.1301.
CY-TM-170-300 Revision 3Page 73 of 209Table 2.1-2Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUMCHANNELSINSTRUMENT OPERABLE APPLICABILITY ACTION1. Containment Purge Monitoring Systema. Noble Gas Activity Monitor (2HP-R-225) 1 NOTE 1 NOTE 2b. Particulate Monitor (2HP-R-225) 1 NOTE 1 NOTE 2c. Effluent System Flow Rate Measuring Device (2AH-FR-5907 Point 1) 1 NOTE 1 NOTE 32. Station Ventilation Systema. Noble Gas Activity Monitor (2HP-R-219) or (2HP-R-219A) 1 NOTE 1 NOTE 2b. Particulate Monitor (2HP-R-219) or (2HP-R-219A) 1 NOTE 1 NOTE 2c. Effluent System Flow Rate Monitoring Device (2AH-FR-5907 Point 6) 1 NOTE 1 NOTE 3NOTES:1. During operation of the monitored system.2. With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, secureReactor Building Purge if in progress.
: 3. With flow rate monitoring instrumentation out of service, flow rates from the Auxiliary (2AH-FR-5907 Point 2), FuelHandling (2AH-FR-5907 Point 4), Soiled Exhaust System (2AH-FR-5907 Point 5), and Reactor Buildings (2AH-FR-5907 Point 1) may be summed individually.
Under these conditions, the flow rate monitoring device is considered operable.
Under these conditions, the flow rate monitoring device is considered operable.
Ifthe flow rates cannot be summed individually, they may be estimated using the maximum design flow for the exhaustfans, and the reporting requirements of Control 2.1.2.b are applicable.
If the flow rates cannot be summed individually, they may be estimated using the maximum design flow for the exhaust fans, and the reporting requirements of Control 2.1.2.b are applicable.
CY-TM-170-300 Revision 3Page 74 of 2092.2 Radioactive Effluent Controls2.2.1 Liquid Effluent Controls2.2.1.1 Liquid Effluent Concentration CONTROL:The concentration of radioactive material released at anytimefrom the unit to unrestricted areas shall be limited to ten timesthe concentrations specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2, Column 2.APPLICABILITY:
CY-TM-170-300 Revision 3 Page 74 of 209 2.2 Radioactive Effluent Controls 2.2.1 Liquid Effluent Controls 2.2.1.1 Liquid Effluent Concentration CONTROL: The concentration of radioactive material released at anytime from the unit to unrestricted areas shall be limited to ten times the concentrations specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2, Column 2.APPLICABILITY:
At all timesACTION:With the concentration of radioactive material released fromthe unit to unrestricted areas exceeding the above limits,immediately restore concentrations within the above limits.BASESThis control is provided to ensure that the concentration ofradioactive materials released in liquid waste effluent from theunit to unrestricted areas will be less than ten times theconcentration levels specified in 10 CFR Part20.1001-20.2401, Appendix B, Table 2. These Controlspermit flexibility under unusual conditions, which maytemporarily result in higher than normal releases, but stillwithin ten times the concentrations, specified in 10 CFR 20. Itis expected that by using this flexibility under unusualconditions, and exerting every effort to keep levels ofradioactive material in liquid wastes as low as practicable, theannual releases will not exceed a small fraction of the annualaverage concentrations specified in 10 CFR 20. As a result,this Control provides reasonable assurance that the resulting annual exposure to an individual in off-site areas will notexceed the design objectives of Section II.A of Appendix I to10 CFR Part 50, which were established as requirements forthe cleanup of TMI-2 in the NRC's Statement of Policy of April27, 1981.
At all times ACTION: With the concentration of radioactive material released from the unit to unrestricted areas exceeding the above limits, immediately restore concentrations within the above limits.BASES This control is provided to ensure that the concentration of radioactive materials released in liquid waste effluent from the unit to unrestricted areas will be less than ten times the concentration levels specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2. These Controls permit flexibility under unusual conditions, which may temporarily result in higher than normal releases, but still within ten times the concentrations, specified in 10 CFR 20. It is expected that by using this flexibility under unusual conditions, and exerting every effort to keep levels of radioactive material in liquid wastes as low as practicable, the annual releases will not exceed a small fraction of the annual average concentrations specified in 10 CFR 20. As a result, this Control provides reasonable assurance that the resulting annual exposure to an individual in off-site areas will not exceed the design objectives of Section II.A of Appendix I to 10 CFR Part 50, which were established as requirements for the cleanup of TMI-2 in the NRC's Statement of Policy of April 27, 1981.
CY-TM-1 70-300Revision 3Page 75 of 2092.2.1.2 Liquid Effluent DoseCONTROLThe dose or dose commitment to a MEMBER OF THEPUBLIC from radioactive materials in liquid effluents releasedfrom the unit to the SITE BOUNDARY shall be limited:a. During any calendar quarter to less than or equal to1.5 mrem to the total body and to less than or equalto 5 mrem to any organ.b. During any calendar year to less than or equal to 3mrem to the total body and to less than or equal to10 mrem to any organ.APPLICABILITY:
CY-TM-1 70-300 Revision 3 Page 75 of 209 2.2.1.2 Liquid Effluent Dose CONTROL The dose or dose commitment to a MEMBER OF THE PUBLIC from radioactive materials in liquid effluents released from the unit to the SITE BOUNDARY shall be limited: a. During any calendar quarter to less than or equal to 1.5 mrem to the total body and to less than or equal to 5 mrem to any organ.b. During any calendar year to less than or equal to 3 mrem to the total body and to less than or equal to 10 mrem to any organ.APPLICABILITY:
At all timesACTION:a. With the calculated dose from the release ofradioactive materials in liquid effluents exceeding any of the above limits, prepare and submit to theNRC Region I Administrator within 30 days, aSpecial Report which identifies the cause(s) forexceeding the limit(s) and defines the corrective actions to be taken to reduce the releases ofradioactive materials in liquid effluents during theremainder of the current calendar quarter andduring the subsequent 3 calendar quarters so thatthe cumulative dose or dose commitment to anyindividual from such releases during these fourcalendar quarters is within 3 mrem to the total bodyand 10 mrem to any organ. This Special Reportshall also include (1) the result of radiological analyses of the drinking water source, and (2) theradiological impact on finished drinking watersupplies with regard to the requirements of 40 CFR141, Safe Drinking Water Act.
At all times ACTION: a. With the calculated dose from the release of radioactive materials in liquid effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit(s) and defines the corrective actions to be taken to reduce the releases of radioactive materials in liquid effluents during the remainder of the current calendar quarter and during the subsequent 3 calendar quarters so that the cumulative dose or dose commitment to any individual from such releases during these four calendar quarters is within 3 mrem to the total body and 10 mrem to any organ. This Special Report shall also include (1) the result of radiological analyses of the drinking water source, and (2) the radiological impact on finished drinking water supplies with regard to the requirements of 40 CFR 141, Safe Drinking Water Act.
CY-TM-1 70-300Revision 3Page 76 of 209BASESThis Control requires that the dose to offsite personnel belimited to the design objectives of Appendix I of 10 CFR Part50. This will assure the dose received by the public duringPDMS is equivalent to or less than that from a normaloperating reactor.
CY-TM-1 70-300 Revision 3 Page 76 of 209 BASES This Control requires that the dose to offsite personnel be limited to the design objectives of Appendix I of 10 CFR Part 50. This will assure the dose received by the public during PDMS is equivalent to or less than that from a normal operating reactor. The limits also assure that the environmental impacts are consistent with those assessed in NUREG-0683, the TMI-2 Programmatic Environmental Impact Statement (PEIS). The ACTION statements provide the required flexibility under unusual conditions and at the same time implement the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive material in liquid effluents will be kept "as low as is reasonably achievable".
The limits also assure that theenvironmental impacts are consistent with those assessed inNUREG-0683, the TMI-2 Programmatic Environmental ImpactStatement (PEIS). The ACTION statements provide therequired flexibility under unusual conditions and at the sametime implement the guides set forth in Section IV.A ofAppendix I to assure that the releases of radioactive materialin liquid effluents will be kept "as low as is reasonably achievable".
The dose calculations in the ODCM implement the requirements in Section lIlA.. of Appendix I that conformance with the guides of Appendix I is to be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.
The dose calculations in the ODCM implement the requirements in Section lIlA.. of Appendix I thatconformance with the guides of Appendix I is to be shown bycalculational procedures based on models and data such thatthe actual exposure of a MEMBER OF THE PUBLIC throughappropriate pathways is unlikely to be substantially underestimated.
The equations specified in the ODCM for calculating the doses due to the actual release rates of radioactive materials in liquid effluents are consistent with the methodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October, 1977, and Regulatory Guide 1.113, "Estimating Aquatic Dispersion of Effluents from Accidental and Routine Reactor Releases for the Purpose of Implementing Appendix I," April, 1977.NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.113.
The equations specified in the ODCM forcalculating the doses due to the actual release rates ofradioactive materials in liquid effluents are consistent with themethodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of ReactorEffluents for the Purpose of Evaluating Compliance with 10CFR Part 50, Appendix I," Revision 1, October, 1977, andRegulatory Guide 1.113, "Estimating Aquatic Dispersion ofEffluents from Accidental and Routine Reactor Releases forthe Purpose of Implementing Appendix I," April, 1977.NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.113.
CY-TM-1 70-300 Revision 3 Page 77 of 209 2.2.1.3 Liquid Radwaste Treatment System CONTROL: The appropriate portions of the liquid radwaste treatment system shall be used to reduce the radioactive materials in liquid wastes prior to their discharge when the projected doses due to the liquid effluent from the unit to unrestricted areas would exceed 0.06 mrem to the total body or 0.2 mrem to any organ in any calendar month.APPLICABILITY:
CY-TM-1 70-300Revision 3Page 77 of 2092.2.1.3 Liquid Radwaste Treatment SystemCONTROL:The appropriate portions of the liquid radwaste treatment system shall be used to reduce the radioactive materials inliquid wastes prior to their discharge when the projected dosesdue to the liquid effluent from the unit to unrestricted areaswould exceed 0.06 mrem to the total body or 0.2 mrem to anyorgan in any calendar month.APPLICABILITY:
At all times ACTION: a. With radioactive liquid waste being discharged without treatment and in excess of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which includes the following information:
At all timesACTION:a. With radioactive liquid waste being discharged without treatment and in excess of the above limits,prepare and submit to the NRC Region IAdministrator within 30 days, a Special Reportwhich includes the following information:
: 1. Explanation of why liquid radwaste was being discharged without treatment, identification of any inoperable equipment or subsystems, and the reason for inoperability, 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and, 3. A summary description of action(s) taken to prevent a recurrence.
: 1. Explanation of why liquid radwaste wasbeing discharged without treatment, identification of any inoperable equipment or subsystems, and the reason forinoperability,
BASES The requirement that the appropriate portions of this system (shared with TMI-1) be used, when specified, provides assurance that the releases of radioactive materials in liquid effluents will be kept as low as is reasonably achievable.
: 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and,3. A summary description of action(s) takento prevent a recurrence.
This control implements the requirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50 and the design objective given in Section II.D of Appendix I to 10 CFR Part 50. The intent of Section ll.D. is to reduce effluents to as low as is reasonably achievable in a cost effective manner. This control satisfies this intent by establishing a dose limit which is a small fraction (25%) of Section II.A of Appendix 1, 10 CFR Part 50 dose requirements.
BASESThe requirement that the appropriate portions of this system(shared with TMI-1) be used, when specified, providesassurance that the releases of radioactive materials in liquideffluents will be kept as low as is reasonably achievable.
Thiscontrol implements the requirements of 10 CFR Part 50.36a,General Design Criterion 60 of Appendix A to 10 CFR Part 50and the design objective given in Section II.D of Appendix I to10 CFR Part 50. The intent of Section ll.D. is to reduceeffluents to as low as is reasonably achievable in a costeffective manner. This control satisfies this intent byestablishing a dose limit which is a small fraction (25%) ofSection II.A of Appendix 1, 10 CFR Part 50 dose requirements.
This margin, a factor of 4, constitutes a reasonable reduction.
This margin, a factor of 4, constitutes a reasonable reduction.
CY-TM-1 70-300Revision 3Page 78 of 2092.2.2 Gaseous Effluent Controls2.2.2.1 Gaseous Effluent Dose RateCONTROL:The dose rate due to radioactive materials released ingaseous effluent from the site shall be limited to the following:
CY-TM-1 70-300 Revision 3 Page 78 of 209 2.2.2 Gaseous Effluent Controls 2.2.2.1 Gaseous Effluent Dose Rate CONTROL: The dose rate due to radioactive materials released in gaseous effluent from the site shall be limited to the following:
: a. For noble gases: less than or equal to 500 mrem/yrto the total body and less than or equal to 3000mrem/yr to the skin, andb. For tritium and all radionuclides in particulate formwith half lives greater than 8 days: less than orequal to 1500 mrem/yr to any organ.APPLICABILITY:
: a. For noble gases: less than or equal to 500 mrem/yr to the total body and less than or equal to 3000 mrem/yr to the skin, and b. For tritium and all radionuclides in particulate form with half lives greater than 8 days: less than or equal to 1500 mrem/yr to any organ.APPLICABILITY:
At all times.ACTION:With the release rate(s) exceeding the above limits,immediately decrease the release rate to comply with theabove limit(s).
At all times.ACTION: With the release rate(s) exceeding the above limits, immediately decrease the release rate to comply with the above limit(s).
CY-TM-1 70-300Revision 3Page 79 of 209BASESThe control provides reasonable assurance that the annualdose at the SITE BOUNDARY from gaseous effluent from allunits on the site will be within the annual dose limits of 10 CFRPart 20 for unrestricted areas. At the same time, theseControls permit flexibility under unusual conditions, which maytemporarily result in higher than the design objective levels,but still within the dose limits specified in 10 CFR 20 andwithin the design objectives of Appendix I to 10 CFR 50. It isexpected that using this flexibility under unusual conditions, and by exerting every effort to keep levels of radioactive material in gaseous wastes as low as practicable, the annualreleases will not exceed a small fraction of the annual doselimits specified in 10 CFR 20 and will not result in doses whichexceed the design objectives of Appendix I to 10 CFR 50,which were endorsed as limits for the cleanup of TMI-2 by theNRC's Statement of Policy of April 27, 1981. These gaseousrelease rates provide reasonable assurance that radioactive material discharged in gaseous effluent will not result in theexposure of a MEMBER OF THE PUBLIC in an unrestricted area, either within or outside the SITE BOUNDARY, to annualaverage concentrations exceeding the values specified inAppendix B, Table 2 of 10 CFR Part 20. For MEMBERS OFTHE PUBLIC who may at times be within the SITEBOUNDARY, the occupancy of the MEMBER OF THEPUBLIC will be sufficiently low to compensate for any increasein the atmospheric diffusion factor above that for the exclusion area boundary.
CY-TM-1 70-300 Revision 3 Page 79 of 209 BASES The control provides reasonable assurance that the annual dose at the SITE BOUNDARY from gaseous effluent from all units on the site will be within the annual dose limits of 10 CFR Part 20 for unrestricted areas. At the same time, these Controls permit flexibility under unusual conditions, which may temporarily result in higher than the design objective levels, but still within the dose limits specified in 10 CFR 20 and within the design objectives of Appendix I to 10 CFR 50. It is expected that using this flexibility under unusual conditions, and by exerting every effort to keep levels of radioactive material in gaseous wastes as low as practicable, the annual releases will not exceed a small fraction of the annual dose limits specified in 10 CFR 20 and will not result in doses which exceed the design objectives of Appendix I to 10 CFR 50, which were endorsed as limits for the cleanup of TMI-2 by the NRC's Statement of Policy of April 27, 1981. These gaseous release rates provide reasonable assurance that radioactive material discharged in gaseous effluent will not result in the exposure of a MEMBER OF THE PUBLIC in an unrestricted area, either within or outside the SITE BOUNDARY, to annual average concentrations exceeding the values specified in Appendix B, Table 2 of 10 CFR Part 20. For MEMBERS OF THE PUBLIC who may at times be within the SITE BOUNDARY, the occupancy of the MEMBER OF THE PUBLIC will be sufficiently low to compensate for any increase in the atmospheric diffusion factor above that for the exclusion area boundary.
The specified release rate limits restrict, at alltimes, the corresponding gamma and beta dose rates abovebackground to a MEMBER OF THE PUBLIC at or beyond theSITE BOUNDARY to less than or equal to 500 mrem/year tothe total body or to less than or equal to 3000 mrem/year tothe skin. The absence of iodine ensures that thecorresponding thyroid dose rate above background to a childvia the inhalation pathway is less than or equal to 1500mrem/yr (NUREG 1301), thus there is no need to specify doserate limits for these nuclides.
The specified release rate limits restrict, at all times, the corresponding gamma and beta dose rates above background to a MEMBER OF THE PUBLIC at or beyond the SITE BOUNDARY to less than or equal to 500 mrem/year to the total body or to less than or equal to 3000 mrem/year to the skin. The absence of iodine ensures that the corresponding thyroid dose rate above background to a child via the inhalation pathway is less than or equal to 1500 mrem/yr (NUREG 1301), thus there is no need to specify dose rate limits for these nuclides.
CY-TM-170-300 Revision 3Page 80 of 2092.2.2.2 Gaseous Effluents Dose-Noble GasesCONTROL:The air dose due to noble gases released in gaseous effluents from the unit to areas at and beyond the SITE BOUNDARYshall be limited to the following:
CY-TM-170-300 Revision 3 Page 80 of 209 2.2.2.2 Gaseous Effluents Dose-Noble Gases CONTROL: The air dose due to noble gases released in gaseous effluents from the unit to areas at and beyond the SITE BOUNDARY shall be limited to the following:
: a. During any calendar quarter:
: a. During any calendar quarter: less than or equal to 5 mrad for gamma radiation and less than or equal to 10 mrad for beta radiation and, b. During any calendar year: less than or equal to 10 mrad for gamma radiation and less than or equal to 20 mrad for beta radiation.
less than or equal to 5mrad for gamma radiation and less than or equal to10 mrad for beta radiation and,b. During any calendar year: less than or equal to 10mrad for gamma radiation and less than or equal to20 mrad for beta radiation.
APPLICABILITY:
APPLICABILITY:
At all times.ACTION:a. With the calculated air dose from radioactive noblegases in gaseous effluents exceeding any of theabove limits, prepare and submit to the NRC RegionI Administrator within 30 days, a Special Reportwhich identifies the cause(s) for exceeding thelimit(s) and defines the corrective actions that havebeen taken to reduce the releases and the proposedcorrective actions to be taken to assure thatsubsequent releases will be in compliance with theabove limits.BASESThis control applies to the release of radioactive materials ingaseous effluents from TMI-2.
At all times.ACTION: a. With the calculated air dose from radioactive noble gases in gaseous effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit(s) and defines the corrective actions that have been taken to reduce the releases and the proposed corrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.BASES This control applies to the release of radioactive materials in gaseous effluents from TMI-2.
CY-TM-1 70-300Revision 3Page 81 of 209.This control and associated action is provided to implement the requirements of Section 1I.B, III.A and IV.A of Appendix I,10 CFR Part 50. The Control implements the guides set forthin Section II.B of Appendix I. The ACTION statements provideflexibility under unusual conditions and at the same timeimplement the guides set forth in Section IV.A of Appendix I toassure that the releases of radioactive material in gaseouseffluents will be kept "as low as is reasonably achievable."
CY-TM-1 70-300 Revision 3 Page 81 of 209.This control and associated action is provided to implement the requirements of Section 1I.B, III.A and IV.A of Appendix I, 10 CFR Part 50. The Control implements the guides set forth in Section II.B of Appendix I. The ACTION statements provide flexibility under unusual conditions and at the same time implement the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive material in gaseous effluents will be kept "as low as is reasonably achievable." The Surveillance Requirements implement the requirements in Section III.A of Appendix I that conformance with the guides of Appendix I be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through the appropriate pathways is unlikely to be substantially underestimated.
The Surveillance Requirements implement the requirements inSection III.A of Appendix I that conformance with the guides ofAppendix I be shown by calculational procedures based onmodels and data such that the actual exposure of a MEMBEROF THE PUBLIC through the appropriate pathways is unlikelyto be substantially underestimated.
The dose calculation methodology and parameters established in the ODCM for calculating the doses due to the actual release rates of radioactive noble gases in gaseous effluents are consistent with the methodology provided in Regulatory Guide 1.109,"Calculation of Annual Doses to Man from Routine Release of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977 and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water Cooled Reactors," Revision 1, July 1977. The ODCM equations provided for determining the air doses at and beyond the SITE BOUNDARY are based upon the historical average atmospheric conditions.
The dose calculation methodology and parameters established in the ODCM forcalculating the doses due to the actual release rates ofradioactive noble gases in gaseous effluents are consistent with the methodology provided in Regulatory Guide 1.109,"Calculation of Annual Doses to Man from Routine Release ofReactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents inRoutine Releases from Light-Water Cooled Reactors,"
NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.111.2.2.2.3 Dose -Iodine-131, Iodine-133, Tritium, and Radionuclides In Particulate Form CONTROL: The dose to a MEMBER OF THE PUBLIC from Tritium and all radionuclides in particulate form with half lives greater than 8 days, in gaseous effluents released from the unit to areas at and beyond the SITE BOUNDARY shall be limited to the following:
Revision 1, July 1977. The ODCM equations provided fordetermining the air doses at and beyond the SITEBOUNDARY are based upon the historical averageatmospheric conditions.
: a. During any calendar quarter: less than or equal to 7.5 mrem to any organ, and b. During any calendar year: less than or equal to 15 mrem to any organ.
NUREG-0133 provides methods fordose calculations consistent with Regulatory Guides 1.109and 1.111.2.2.2.3 Dose -Iodine-131, Iodine-133,  
CY-TM-1 70-300 Revision 3 Page 82 of 209 APPLICABILITY:
: Tritium, and Radionuclides InParticulate FormCONTROL:The dose to a MEMBER OF THE PUBLIC from Tritium and allradionuclides in particulate form with half lives greater than 8days, in gaseous effluents released from the unit to areas atand beyond the SITE BOUNDARY shall be limited to thefollowing:
At all times.ACTION: With the calculated dose from the release of Tritium and radionuclides in particulate form with half lives greater than 8 days, in gaseous effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit and defines the corrective actions that have been taken to reduce the releases and the proposed corrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.
: a. During any calendar quarter:
CY-TM-1 70-300 Revision 3 Page 83 of 209 BASES This control applies to the release of radioactive materials in gaseous effluents from TMI-2.This control and associated action is provided to implement the requirements of Section II.C, III.A and IV.A of Appendix I, 10 CFR Part 50. The Controls are the guides set forth in Section II.C of Appendix I. The ACTION statement provides flexibility during unusual conditions and at the same time implements the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive materials in gaseous effluents will be kept "as low as is reasonably achievable." The ODCM calculational methods specified in the surveillance requirements implement the requirements in Section III.A of Appendix I that conformance with the guides of Appendix I be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.
less than or equal to7.5 mrem to any organ, andb. During any calendar year: less than or equal to 15mrem to any organ.
The ODCM calculational methodology and parameters for calculating the doses due to the actual release rates of the subject materials are consistent with the methodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October, 1977 and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors," Revision 1, July, 1977. These equations also provide for determining the actual doses based upon the historical average atmospheric conditions.
CY-TM-1 70-300Revision 3Page 82 of 209APPLICABILITY:
The release rate controls for iodine-131, iodine-133, tritium and radionuclides in particulate form with half lives greater than 8 days are dependent upon the existing radionuclide pathways to man, in areas at and beyond the SITE BOUNDARY.
At all times.ACTION:With the calculated dose from the release of Tritium andradionuclides in particulate form with half lives greater than 8days, in gaseous effluents exceeding any of the above limits,prepare and submit to the NRC Region I Administrator within30 days, a Special Report which identifies the cause(s) forexceeding the limit and defines the corrective actions thathave been taken to reduce the releases and the proposedcorrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.
The pathways that were examined in the development of these calculations were: 1) individual inhalation of airborne radionuclides, 2) deposition of radionuclides onto green leafy vegetation with subsequent consumption by man, 3) deposition onto grassy areas where milk animals and meat producing animals graze with consumption of the milk and meat by man, and 4) deposition on the ground with subsequent exposure of man. The absence of iodines at the site eliminates the need to specify dose limits for these nuclides.
CY-TM-1 70-300Revision 3Page 83 of 209BASESThis control applies to the release of radioactive materials ingaseous effluents from TMI-2.This control and associated action is provided to implement the requirements of Section II.C, III.A and IV.A of Appendix I,10 CFR Part 50. The Controls are the guides set forth inSection II.C of Appendix I. The ACTION statement providesflexibility during unusual conditions and at the same timeimplements the guides set forth in Section IV.A of Appendix Ito assure that the releases of radioactive materials in gaseouseffluents will be kept "as low as is reasonably achievable."
CY-TM-1 70-300 Revision 3 Page 84 of 209 2.2.2.4 Ventilation Exhaust Treatment System CONTROL The VENTILATION EXHAUST TREATMENT SYSTEM shall be OPERABLE.
The ODCM calculational methods specified in the surveillance requirements implement the requirements in Section III.A ofAppendix I that conformance with the guides of Appendix I beshown by calculational procedures based on models and datasuch that the actual exposure of a MEMBER OF THE PUBLICthrough appropriate pathways is unlikely to be substantially underestimated.
The appropriate portions of the VENTILATION EXHAUST TREATMENT SYSTEM shall be used to reduce radioactive materials in gaseous waste prior to their discharge when the monthly projected doses due to gaseous effluent releases from the site would exceed 0.3 mrem to any organ.APPLICABILITY:
The ODCM calculational methodology andparameters for calculating the doses due to the actual releaserates of the subject materials are consistent with themethodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of ReactorEffluents for the Purpose of Evaluating Compliance with 10CFR Part 50, Appendix I," Revision 1, October, 1977 andRegulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in RoutineReleases from Light-Water-Cooled Reactors,"
At all times.ACTION: a. With the VENTILATION EXHAUST TREATMENT SYSTEM inoperable for more than a month or with gaseous waste being discharged without treatment and in excess of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which includes the following information:
Revision 1,July, 1977. These equations also provide for determining theactual doses based upon the historical average atmospheric conditions.
: 1. Identification of the inoperable equipment or subsystems and the reason for inoperability, 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and 3. A summary description of action(s) taken to prevent a recurrence.
The release rate controls for iodine-131, iodine-133, tritium and radionuclides in particulate form withhalf lives greater than 8 days are dependent upon the existingradionuclide pathways to man, in areas at and beyond theSITE BOUNDARY.
BASES The use of the VENTILATION EXHAUST TREATMENT SYSTEM ensures that gaseous effluents are treated as appropriate prior to release to the environment.
The pathways that were examined in thedevelopment of these calculations were: 1) individual inhalation of airborne radionuclides,  
The appropriate portions of this system provide reasonable assurance that the releases of radioactive materials in gaseous effluents will be kept "as low as is reasonably achievable." This control implements the requirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50, and the design objectives given in Section II.D of Appendix I to 10 CFR Part 50. The specified limits governing the use of appropriate portions of the systems were CY-TM-170-300 Revision 3 Page 85 of 209 specified as a suitable fraction of the guide set forth in Sections II.B and II.C of Appendix 1, 10 CFR Part 50, for gaseous effluents.
: 2) deposition ofradionuclides onto green leafy vegetation with subsequent consumption by man, 3) deposition onto grassy areas wheremilk animals and meat producing animals graze withconsumption of the milk and meat by man, and 4) deposition on the ground with subsequent exposure of man. Theabsence of iodines at the site eliminates the need to specifydose limits for these nuclides.
2.2.3 Total Radioactive Effluent Controls 2.2.3.1 Total Dose CONTROL: The annual (calendar year) dose or dose commitment to any MEMBER OF THE PUBLIC, due to releases of radioactivity and to radiation from uranium fuel cycle sources shall be limited to less than or equal to 25 mrem to the total body or any organ except the thyroid, which shall be limited to less than or equal to 75 mrem.APPLICABILITY:
CY-TM-1 70-300Revision 3Page 84 of 2092.2.2.4 Ventilation Exhaust Treatment SystemCONTROLThe VENTILATION EXHAUST TREATMENT SYSTEM shallbe OPERABLE.
At all times.ACTION: With the calculated dose from the release of radioactive materials in liquid or gaseous effluents exceeding twice the limits of Controls 2.2.1.2.a, 2.2.1.2.b, 2.2.2.2.a, 2.2.2.2.b, 2.2.2.3.a, or, 2.2.2.3.b, calculations should be made including direct radiation contributions from the unit and from outside storage tanks to determine whether the above limits of Control 2.2.3.1 have been exceeded.
The appropriate portions of theVENTILATION EXHAUST TREATMENT SYSTEM shall beused to reduce radioactive materials in gaseous waste prior totheir discharge when the monthly projected doses due togaseous effluent releases from the site would exceed 0.3mrem to any organ.APPLICABILITY:
If such is the case, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which defines the corrective action to be taken to reduce subsequent releases to prevent recurrence of exceeding the above limits and includes the schedule for achieving conformance with the above limits. This Special Report, as defined in 10 CFR Part 20.2203(b), shall include an analysis which estimates the radiation exposure (dose) to a MEMBER OF THE PUBLIC from uranium fuel cycle sources, including all effluent pathways and direct radiation, for the calendar year that includes the release(s) covered by this report. It shall also describe levels of radiation and concentrations of radioactive material involved, and the cause of the exposure levels or concentrations.
At all times.ACTION:a. With the VENTILATION EXHAUST TREATMENT SYSTEM inoperable for more than a month or withgaseous waste being discharged without treatment and in excess of the above limits, prepare andsubmit to the NRC Region I Administrator within 30days, a Special Report which includes the following information:
If the estimated dose(s) exceed the above limits, and if the release condition resulting in violation of 40 CFR 190 has not already been corrected, the Special Report shall include a request for a variance in accordance with the provisions of 40 CFR 190.Submittal of the report is considered a timely request, and a variance is granted until staff action on the request is complete.
: 1. Identification of the inoperable equipment or subsystems and the reason forinoperability,
CY-TM-1 70-300 Revision 3 Page 86 of 209 BASES This control is provided to meet the dose limitations of 40 CFR Part 190 that have been incorporated into 10 CFR Part 20.1301(d).
: 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and3. A summary description of action(s) takento prevent a recurrence.
This control requires the preparation and submittal of a Special Report whenever the calculated doses from plant generated radioactive effluents and direct radiation exceed 25 mrem to the total body or any organ, except the thyroid, which shall be limited to less than or equal to 75 mrem. For sites containing up to 4 reactors, it is highly unlikely that the resultant dose to a MEMBER OF THE PUBLIC will exceed the dose limits of 40 CFR Part 190 if the individual reactors remain within twice the dose design objectives of Appendix I, and if direct radiation doses from the reactor units and outside storage tanks are kept small. The Special Report will describe a course of action that should result in the limitation of the annual dose to a MEMBER OF THE PUBLIC to within the 40 CFR Part 190 limits. For the purposes of the Special Report, it may be assumed that the dose commitment to the member of the public from other uranium fuel cycle sources is negligible, with the exception that dose contributions from other nuclear fuel cycle facilities at the same site or within a radius of 8 km must be considered.
BASESThe use of the VENTILATION EXHAUST TREATMENT SYSTEM ensures that gaseous effluents are treated asappropriate prior to release to the environment.
If the dose to any member of the public is estimated to exceed the requirements of 40 CFR Part 190, the Special Report with a request for a variance (provided the release conditions resulting in violation of 40 CFR Part 190 have not already been corrected), in accordance with the provisions of 40 CFR Part 190.11 and 10 CFR Part 20.2203(b), is considered to be a timely request and fulfills the requirements of 40 CFR Part 190 until NRC staff action is completed.
Theappropriate portions of this system provide reasonable assurance that the releases of radioactive materials ingaseous effluents will be kept "as low as is reasonably achievable."
The variance only relates to the limits of 40 CFR Part 190, and does not apply in any way to the other requirements for dose limitation of 10 CFR Part 20, as addressed in Controls 2.2.1.1 and 2.2.2.1. An individual is not considered a MEMBER OF THE PUBLIC during any period in which he/she is engaged in carrying out any operation that is part of the nuclear fuel cycle.
This control implements the requirements of 10CFR Part 50.36a, General Design Criterion 60 of Appendix Ato 10 CFR Part 50, and the design objectives given in SectionII.D of Appendix I to 10 CFR Part 50. The specified limitsgoverning the use of appropriate portions of the systems were CY-TM-170-300 Revision 3Page 85 of 209specified as a suitable fraction of the guide set forth inSections II.B and II.C of Appendix 1, 10 CFR Part 50, forgaseous effluents.
CY-TM-170-300 Revision 3 Page 87 of 209 3.0 SURVEILLANCES 3.0.1 Surveillance Requirements shall be applicable during the conditions specified for individual Controls unless otherwise stated in an individual Surveillance Requirement.
2.2.3 Total Radioactive Effluent Controls2.2.3.1 Total DoseCONTROL:The annual (calendar year) dose or dose commitment to anyMEMBER OF THE PUBLIC, due to releases of radioactivity and to radiation from uranium fuel cycle sources shall belimited to less than or equal to 25 mrem to the total body orany organ except the thyroid, which shall be limited to lessthan or equal to 75 mrem.APPLICABILITY:
The Surveillance Requirements shall be performed to demonstrate compliance with the OPERABILITY requirements of the Control.3.0.2 Each Surveillance Requirement shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% of the surveillance interval.3.0.3 Failure to perform a Surveillance Requirement within the time interval specified in Section 3.0.2 shall constitute non-compliance with OPERABILITY requirements for a Control. The time limits of the ACTION requirements are applicable at the time it is identified that a Surveillance Requirement has not been performed.
At all times.ACTION:With the calculated dose from the release of radioactive materials in liquid or gaseous effluents exceeding twice thelimits of Controls 2.2.1.2.a, 2.2.1.2.b, 2.2.2.2.a, 2.2.2.2.b, 2.2.2.3.a, or, 2.2.2.3.b, calculations should be made including direct radiation contributions from the unit and from outsidestorage tanks to determine whether the above limits of Control2.2.3.1 have been exceeded.
The ACTION requirements may be delayed for up to 24 hours to permit completion of the surveillance when the allowable outage time limits of the ACTION requirements are less than 24 hours. Surveillance Requirements do not have to be performed on inoperable equipment.
If such is the case, prepare andsubmit to the NRC Region I Administrator within 30 days, aSpecial Report which defines the corrective action to be takento reduce subsequent releases to prevent recurrence ofexceeding the above limits and includes the schedule forachieving conformance with the above limits. This SpecialReport, as defined in 10 CFR Part 20.2203(b),
3.1 Radioactive Effluent Instrumentation 3.1.1 Radioactive Liquid Effluent Instrumentation SURVEILLANCE REQUIREMENTS 3.1.1.1 Radioactive Liquid Effluent Instrumentation is common between TMI-1 and TMI-2. Surveillances for this instrumentation are specified in ODCM Part I, Surveillance 3.1.1.3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation SURVEILLANCE REQUIREMENTS 3.1.2.1 Each radioactive gaseous process or effluent monitoring instrumentation channel shall be demonstrated OPERABLE by performance of the CHANNEL CHECK, SOURCE CHECK, CHANNEL CALIBRATION, and CHANNEL TEST operations at the frequencies shown in Table 3.1-2.
shall include ananalysis which estimates the radiation exposure (dose) to aMEMBER OF THE PUBLIC from uranium fuel cycle sources,including all effluent pathways and direct radiation, for thecalendar year that includes the release(s) covered by thisreport. It shall also describe levels of radiation andconcentrations of radioactive material  
CY-TM-1 70-300 Revision 3 Page 88 of 209 Table 3.1-2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL CHECK INSTRUMENT
: involved, and the causeof the exposure levels or concentrations.
: 1. Containment Purge Monitoring System a. Noble Gas Activity Monitor (2HP-R-225)
If the estimated dose(s) exceed the above limits, and if the release condition resulting in violation of 40 CFR 190 has not already beencorrected, the Special Report shall include a request for avariance in accordance with the provisions of 40 CFR 190.Submittal of the report is considered a timely request, and avariance is granted until staff action on the request iscomplete.
CY-TM-1 70-300Revision 3Page 86 of 209BASESThis control is provided to meet the dose limitations of 40 CFRPart 190 that have been incorporated into 10 CFR Part20.1301(d).
This control requires the preparation andsubmittal of a Special Report whenever the calculated dosesfrom plant generated radioactive effluents and direct radiation exceed 25 mrem to the total body or any organ, except thethyroid, which shall be limited to less than or equal to 75mrem. For sites containing up to 4 reactors, it is highlyunlikely that the resultant dose to a MEMBER OF THEPUBLIC will exceed the dose limits of 40 CFR Part 190 if theindividual reactors remain within twice the dose designobjectives of Appendix I, and if direct radiation doses from thereactor units and outside storage tanks are kept small. TheSpecial Report will describe a course of action that shouldresult in the limitation of the annual dose to a MEMBER OFTHE PUBLIC to within the 40 CFR Part 190 limits. For thepurposes of the Special Report, it may be assumed that thedose commitment to the member of the public from otheruranium fuel cycle sources is negligible, with the exception that dose contributions from other nuclear fuel cycle facilities at the same site or within a radius of 8 km must beconsidered.
If the dose to any member of the public isestimated to exceed the requirements of 40 CFR Part 190, theSpecial Report with a request for a variance (provided therelease conditions resulting in violation of 40 CFR Part 190have not already been corrected),
in accordance with theprovisions of 40 CFR Part 190.11 and 10 CFR Part20.2203(b),
is considered to be a timely request and fulfills therequirements of 40 CFR Part 190 until NRC staff action iscompleted.
The variance only relates to the limits of 40 CFRPart 190, and does not apply in any way to the otherrequirements for dose limitation of 10 CFR Part 20, asaddressed in Controls 2.2.1.1 and 2.2.2.1.
An individual is notconsidered a MEMBER OF THE PUBLIC during any period inwhich he/she is engaged in carrying out any operation that ispart of the nuclear fuel cycle.
CY-TM-170-300 Revision 3Page 87 of 2093.0 SURVEILLANCES 3.0.1 Surveillance Requirements shall be applicable during the conditions specified for individual Controls unless otherwise stated in an individual Surveillance Requirement.
The Surveillance Requirements shall beperformed to demonstrate compliance with the OPERABILITY requirements of the Control.3.0.2 Each Surveillance Requirement shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% ofthe surveillance interval.
3.0.3 Failure to perform a Surveillance Requirement within the time intervalspecified in Section 3.0.2 shall constitute non-compliance withOPERABILITY requirements for a Control.
The time limits of theACTION requirements are applicable at the time it is identified that aSurveillance Requirement has not been performed.
The ACTIONrequirements may be delayed for up to 24 hours to permit completion ofthe surveillance when the allowable outage time limits of the ACTIONrequirements are less than 24 hours. Surveillance Requirements do nothave to be performed on inoperable equipment.
3.1 Radioactive Effluent Instrumentation 3.1.1 Radioactive Liquid Effluent Instrumentation SURVEILLANCE REQUIREMENTS 3.1.1.1 Radioactive Liquid Effluent Instrumentation is commonbetween TMI-1 and TMI-2. Surveillances for thisinstrumentation are specified in ODCM Part I,Surveillance 3.1.1.3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation SURVEILLANCE REQUIREMENTS 3.1.2.1 Each radioactive gaseous process or effluent monitoring instrumentation channel shall be demonstrated OPERABLE byperformance of the CHANNEL CHECK, SOURCE CHECK,CHANNEL CALIBRATION, and CHANNEL TEST operations at the frequencies shown in Table 3.1-2.
CY-TM-1 70-300Revision 3Page 88 of 209Table 3.1-2Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNELCHECKINSTRUMENT
: 1. Containment Purge Monitoring Systema. Noble Gas Activity Monitor (2HP-R-225)
: b. Particulate Sampler (2HP-R-225)
: b. Particulate Sampler (2HP-R-225)
CHANNELCALIBRATION EN/ACHANNELFUNCTIONAL TESTMN/AAPPLICABILITY NOTE 1NOTE 1Dw2. Station Ventilation Monitoring Systema. Noble Gas Activity Monitor (2HP-R-219) and (2HP-R-219A)
CHANNEL CALIBRATION E N/A CHANNEL FUNCTIONAL TEST M N/A APPLICABILITY NOTE 1 NOTE 1 D w 2. Station Ventilation Monitoring System a. Noble Gas Activity Monitor (2HP-R-219) and (2HP-R-219A)
: b. Particulate Sampler (2HP-R-219) and (2HP-R-219A)
: b. Particulate Sampler (2HP-R-219) and (2HP-R-219A)
NOTES:1. During operation of the monitored system.DwEN/AMN/ANOTE 1NOTE 1 CY-TM-170-300 Revision 3Page 89 of 2093.2 Radioactive Effluents 3.2.1 Liquid Effluents SURVEILLANCE REQUIREMENTS 3.2.1.1 Concentration 3.2.1.1.1 The radioactivity content of each batch ofradioactive liquid waste shall be determined bysampling and analysis in accordance with Table3.2-1. The results of analyses shall be used withthe calculational methods in the ODCM to assurethat the concentration at the point of release ismaintained within the limits of Control 2.2.1 .1.3.2.1.1.2 Analysis of samples composited from batchreleases shall be performed in accordance withTable 3.2-1. The results of the analysis shall beused with the calculational methods in the ODCM toassure that the concentrations at the point ofrelease were maintained within the limits of Control2.2.1.1.3.2.1.1.3 The radioactivity concentration of liquids discharged from continuous release points shall be determined by collection and analysis of samples in accordance with Table 3.2-1. The results of the analysis shallbe used with the calculational methods of theODCM to assure that the concentration at the pointof release is maintained within the limits of Control2.2.1.1.3.2.1.2 Dose Calculations 3.2.1.2.1 Cumulative dose contributions from liquid effluents shall be determined in accordance with the OffsiteDose Calculation Manual (ODCM) at least once amonth.3.2.1.3 Dose Projections 3.2.1.3.1 Doses due to liquid releases shall be projected atleast once a month, in accordance with the ODCM.
NOTES: 1. During operation of the monitored system.D w E N/A M N/A NOTE 1 NOTE 1 CY-TM-170-300 Revision 3 Page 89 of 209 3.2 Radioactive Effluents 3.2.1 Liquid Effluents SURVEILLANCE REQUIREMENTS 3.2.1.1 Concentration 3.2.1.1.1 The radioactivity content of each batch of radioactive liquid waste shall be determined by sampling and analysis in accordance with Table 3.2-1. The results of analyses shall be used with the calculational methods in the ODCM to assure that the concentration at the point of release is maintained within the limits of Control 2.2.1 .1.3.2.1.1.2 Analysis of samples composited from batch releases shall be performed in accordance with Table 3.2-1. The results of the analysis shall be used with the calculational methods in the ODCM to assure that the concentrations at the point of release were maintained within the limits of Control 2.2.1.1.3.2.1.1.3 The radioactivity concentration of liquids discharged from continuous release points shall be determined by collection and analysis of samples in accordance with Table 3.2-1. The results of the analysis shall be used with the calculational methods of the ODCM to assure that the concentration at the point of release is maintained within the limits of Control 2.2.1.1.3.2.1.2 Dose Calculations 3.2.1.2.1 Cumulative dose contributions from liquid effluents shall be determined in accordance with the Offsite Dose Calculation Manual (ODCM) at least once a month.3.2.1.3 Dose Projections 3.2.1.3.1 Doses due to liquid releases shall be projected at least once a month, in accordance with the ODCM.
CY-TM-170-300 Revision 3Page 90 of 209TABLE 3.2-1Radioactive Liquid Waste Sampling and Analysis Program (4, 5)A. Liquid ReleasesSampling Frequency Type of Detectable Activity Analysis Concentration (3)P Individual Gamma 5E-7 &#xfd;LCi/ml (2)Each Batch H-3 1 E-5 &#xfd;tCi/mlQ Gross Alpha 1 E-7 JLCi/mlQuarterly Composite (1) Sr-90 5E-8 jtCi/mlNOTES:(1) A COMPOSITE SAMPLE is one in which the quantity of liquid sampled is proportional to the quantity of liquid waste discharged from the plant.(2) For certain mixtures of gamma emitters, it may not be possible to measureradionuclides in concentrations near this sensitivity limit when other nuclides arepresent in the sample in much greater concentrations.
CY-TM-170-300 Revision 3 Page 90 of 209 TABLE 3.2-1 Radioactive Liquid Waste Sampling and Analysis Program (4, 5)A. Liquid Releases Sampling Frequency Type of Detectable Activity Analysis Concentration (3)P Individual Gamma 5E-7 &#xfd;LCi/ml (2)Each Batch H-3 1 E-5 &#xfd;tCi/ml Q Gross Alpha 1 E-7 JLCi/ml Quarterly Composite (1) Sr-90 5E-8 jtCi/ml NOTES: (1) A COMPOSITE SAMPLE is one in which the quantity of liquid sampled is proportional to the quantity of liquid waste discharged from the plant.(2) For certain mixtures of gamma emitters, it may not be possible to measure radionuclides in concentrations near this sensitivity limit when other nuclides are present in the sample in much greater concentrations.
Under these circumstances, itwill be more appropriate to calculate the concentrations of such radionuclides usingmeasured ratios with those radionuclides, which are routinely identified and measured.
Under these circumstances, it will be more appropriate to calculate the concentrations of such radionuclides using measured ratios with those radionuclides, which are routinely identified and measured.(3) The detectability limits for radioactivity analysis are based on the technical feasibility and on the potential significance in the environment of the quantities released.
(3) The detectability limits for radioactivity analysis are based on the technical feasibility and on the potential significance in the environment of the quantities released.
For some nuclides, lower detection limits may be readily achievable and when nuclides are measured below the stated limits, they should also be reported.(4) The results of these analyses should be used as the basis for recording and reporting the quantities of radioactive material released in liquid effluents during the sampling period. In estimating releases for a period when analyses were not performed, the average of the two adjacent data points spanning this period should be used. Such estimates should be included in the effluent records and reports; however, they should be clearly identified as estimates, and the method used to obtain these data should be described.
Forsome nuclides, lower detection limits may be readily achievable and when nuclides aremeasured below the stated limits, they should also be reported.
(5) Deviations from the sampling/analysis regime will be noted in the report specified in ODCM Part IV.
(4) The results of these analyses should be used as the basis for recording and reporting the quantities of radioactive material released in liquid effluents during the samplingperiod. In estimating releases for a period when analyses were not performed, theaverage of the two adjacent data points spanning this period should be used. Suchestimates should be included in the effluent records and reports;  
CY-TM-1 70-300 Revision 3 Page 91 of 209 3.2.2 Gaseous Effluents SURVEILLANCE REQUIREMENTS 3.2.2.1 Dose Rates 3.2.2.1.1 The dose rate due to noble gases in gaseous effluents shall be determined to be within the limits of Control 2.2.2.1 .a in accordance with the methods and procedures of the ODCM.3.2.2.1.2 The dose rate of radioactive materials, other than noble gases, in gaseous effluents shall be determined to be within the limits of Control 2.2.2.1.b in accordance with methods and procedures of the ODCM by obtaining representative samples and performing analyses in accordance with the sampling and analysis program, specified in Table 3.2-2.3.2.2.2 Dose, Noble Gas 3.2.2.2.1 Cumulative dose contributions from noble gas effluents for the current calendar quarter and current calendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM) monthly.3.2.2.3 Dose, Tritium and Radionuclides In Particulate Form 3.2.2.3.1 Cumulative dose contributions from Tritium and radionuclides in particulate form with half lives greater than 8 days for the current calendar quarter and current calendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM) monthly.3.2.2.4 Ventilation Exhaust Treatment 3.2.2.4.1 Doses due to gaseous releases from the unit shall be projected monthly in accordance with the ODCM.
: however, they shouldbe clearly identified as estimates, and the method used to obtain these data should bedescribed.
CY-TM-1 70-300 Revision 3 Page 92 of 209 TABLE 3.2-2 Radioactive Gaseous Waste Sampling and Analysis Program (3)SAMPLING TYPE OF DETECTABLE SAMPLE FREQUENC ACTIVITY CONCENTRATION SAMPLE POINT TYPE Y ANALYSIS (1)(a)P H-3 1 E-6 pCi/cc Reactor Building Purge Gas Individual Releases Each Purge Gamma Emitters 1E-4 tCi/cc (2)M H-3 1E-6 gCi/cc Unit Exhaust Vent Release Gas Individual Points Monthly Gamma Emitters 1 E-4 gtCi/cc (2)W Individual (b) 1E-10 pCi/cc (2)Weekly Gamma Emitters M Particulate Monthly Sr-90 1 E-1 1 p.Ci/cc s Composite M Monthly Gross Alpha Mnhy Emitters 1 E-1 1 gCi/cc Composite Indv. Gam ma 1E 10 g ic 2 Reactor Building Breather SA Emitters (b) E- Ci/cc (2)Particulate SAEitr(b Semi-Annual Sr-90 1 E-1 1 gCi/cc ly Gross Alpha 1 E-1 1 pCi/cc Emitters 1E-11_____i/cc (1) The above detectability limits are based on technical feasibility and on the potential significance in the environment of the quantities released.
(5) Deviations from the sampling/analysis regime will be noted in the report specified inODCM Part IV.
For some nuclides, lower detection limits may be readily achievable and when nuclides are measured below the stated limits, they should also be reported.(2) For certain mixtures of gamma emitters, it may be possible to measure radionuclides at levels near their sensitivity limits when other nuclides are present in the sample at much higher levels. Under these circumstances, it will be more appropriate to calculate the levels of such radionuclides using observed ratios in the gaseous component in the reactor coolant for those radionuclides which are measurable.
CY-TM-1 70-300Revision 3Page 91 of 2093.2.2 Gaseous Effluents SURVEILLANCE REQUIREMENTS 3.2.2.1 Dose Rates3.2.2.1.1 The dose rate due to noble gases in gaseouseffluents shall be determined to be within the limitsof Control 2.2.2.1 .a in accordance with the methodsand procedures of the ODCM.3.2.2.1.2 The dose rate of radioactive materials, other thannoble gases, in gaseous effluents shall bedetermined to be within the limits of Control2.2.2.1.b in accordance with methods andprocedures of the ODCM by obtaining representative samples and performing analyses inaccordance with the sampling and analysisprogram, specified in Table 3.2-2.3.2.2.2 Dose, Noble Gas3.2.2.2.1 Cumulative dose contributions from noble gaseffluents for the current calendar quarter and currentcalendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL(ODCM) monthly.3.2.2.3 Dose, Tritium and Radionuclides In Particulate Form3.2.2.3.1 Cumulative dose contributions from Tritium andradionuclides in particulate form with half livesgreater than 8 days for the current calendar quarterand current calendar year shall be determined inaccordance with the OFFSITE DOSECALCULATION MANUAL (ODCM) monthly.3.2.2.4 Ventilation Exhaust Treatment 3.2.2.4.1 Doses due to gaseous releases from the unit shallbe projected monthly in accordance with the ODCM.
(3) Deviations from the sampling and analysis regime will be noted in the report specified in ODCM Part IV.
CY-TM-1 70-300Revision 3Page 92 of 209TABLE 3.2-2Radioactive Gaseous Waste Sampling and Analysis Program (3)SAMPLING TYPE OF DETECTABLE SAMPLE FREQUENC ACTIVITY CONCENTRATION SAMPLE POINT TYPE Y ANALYSIS (1)(a)P H-3 1 E-6 pCi/ccReactor Building Purge Gas Individual Releases Each Purge Gamma Emitters 1E-4 tCi/cc (2)M H-3 1E-6 gCi/ccUnit Exhaust Vent Release Gas Individual Points Monthly Gamma Emitters 1 E-4 gtCi/cc (2)W Individual (b) 1E-10 pCi/cc (2)Weekly Gamma EmittersMParticulate Monthly Sr-90 1 E-1 1 p.Ci/ccs Composite MMonthly Gross AlphaMnhy Emitters 1 E-1 1 gCi/ccComposite Indv. Gam ma 1E 10 g ic 2Reactor Building Breather SA Emitters (b) E- Ci/cc (2)Particulate SAEitr(bSemi-Annual Sr-90 1 E-1 1 gCi/ccly Gross Alpha 1 E-1 1 pCi/ccEmitters 1E-11_____i/cc (1) The above detectability limits are based on technical feasibility and on the potential significance in the environment of the quantities released.
CY-TM-1 70-300 Revision 3 Page 93 of 209 TABLE 3.2-2 (Cont'd)Radioactive Gaseous Waste Sampling and Analysis Program Table Notation a. The LLD is the smallest concentration of radioactive material in a sample that will be detected with 95% probability with 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):
For some nuclides, lowerdetection limits may be readily achievable and when nuclides are measured below thestated limits, they should also be reported.
4.66 sp LED =E x V x 2.22 x 106 x Y x exp (-XAt)Where LLD is the lower limit of detection as defined above (as picocurie per unit mass or volume).Sb is the standard deviation of the background counting rate or of the counting rate of a blank sample as appropriate (as counts per minute).E is the counting efficiency (as counts per transformation), V is the sample size (in units of mass or volume), 2.22 is the number of transformations per minute per picocurie, Y is the fractional radiochemical yield (when applicable), X is the radioactive decay constant for the particular radionuclide, and At is the elapsed time between midpoint of sample collection and time of counting (for plant effluents, not environmental samples), The value of Sb used in the calculation of the LLD for a detection system shall be based on the actual observed variance of the background counting rate or of the counting rate of the blank samples (as appropriate) rather than on an unverified theoretically predicted variance.
(2) For certain mixtures of gamma emitters, it may be possible to measure radionuclides atlevels near their sensitivity limits when other nuclides are present in the sample at muchhigher levels. Under these circumstances, it will be more appropriate to calculate thelevels of such radionuclides using observed ratios in the gaseous component in thereactor coolant for those radionuclides which are measurable.
In calculating the LLD for a radionuclide determined by gamma-ray spectrometry, the background shall include the typical contributions of other radionuclides normally present in the samples. Typical values of E, V, Y, and At shall be used in the calculation.
(3) Deviations from the sampling and analysis regime will be noted in the report specified inODCM Part IV.
The background count rate is calculated from the background counts, that are determined to be with +/-one FWHM (Full-Width-at-Half-Maximum) energy band about the energy of the gamma-ray peak used for the quantitative analysis for that radionuclide.
CY-TM-1 70-300Revision 3Page 93 of 209TABLE 3.2-2 (Cont'd)Radioactive Gaseous Waste Sampling and Analysis ProgramTable Notationa. The LLD is the smallest concentration of radioactive material in a sample that willbe detected with 95% probability with 5% probability of falsely concluding that ablank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):
CY-TM-170-300 Revision 3 Page 94 of 209 TABLE 3.2-2 Notation (Cont'd)b. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:
4.66 spLED =E x V x 2.22 x 106 x Y x exp (-XAt)WhereLLD is the lower limit of detection as defined above (as picocurie per unit mass orvolume).Sb is the standard deviation of the background counting rate or of the countingrate of a blank sample as appropriate (as counts per minute).E is the counting efficiency (as counts per transformation),
Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99, Cs-1 34, Cs-1 37, Ce-141 and Ce-1 44 for particulate emissions.
V is the sample size (in units of mass or volume),2.22 is the number of transformations per minute per picocurie, Y is the fractional radiochemical yield (when applicable),
This list does not mean that only these nuclides are to be detected and reported.
X is the radioactive decay constant for the particular radionuclide, andAt is the elapsed time between midpoint of sample collection and time of counting(for plant effluents, not environmental samples),
Other peaks which are measurable and identifiable, together with the above nuclides, shall also be identified and reported.
The value of Sb used in the calculation of the LLD for a detection system shall bebased on the actual observed variance of the background counting rate or of thecounting rate of the blank samples (as appropriate) rather than on an unverified theoretically predicted variance.
Nuclides which are below the LLD for the analyses shall be reported as "less than" the nuclide's LLD and shall not be reported as being present at the LLD level for that nuclide. The "less than" values shall not be used in the required dose calculations.
In calculating the LLD for a radionuclide determined by gamma-ray spectrometry, the background shall include the typicalcontributions of other radionuclides normally present in the samples.
CY-TM-170-300 Revision 3 Page 95 of 209 3.2.3 Total Radioactive Effluents 3.2.3.1 Dose Calculation 3.2.3.1.1 Cumulative annual dose contributions from liquid and gaseous effluents shall be determined in accordance with Surveillances 3.2.1.2.1, 3.2.2.2.1, and 3.2.2.3.1, including direct radiation contributions from the Unit and from outside storage tanks, and in accordance with the methodology contained in the ODCM.
Typicalvalues of E, V, Y, and At shall be used in the calculation.
CY-TM-1 70-300 Revision 3 Page 96 of 209 4.0 PART II REFERENCES 4.1 NUREG-0683, "Final Programmatic Environmental Impact Statement related to decontamination and disposal of radioactive wastes resulting from March 28, 1979, accident Three Mile Island Nuclear Station, Unit 2," March 1981, and its supplements.
The background countrate is calculated from the background counts, that are determined to be with +/-one FWHM (Full-Width-at-Half-Maximum) energy band about the energy of thegamma-ray peak used for the quantitative analysis for that radionuclide.
4.2 TMI-2 PDMS Technical Specifications, attached to Facility License No. DPR-73 4.3 Title 10, Code of Federal Regulations, "Energy" 4.4 "Statement of Policy Relative to the NRC Programmatic Environmental Impact Statement on the Cleanup of Three Mile Island Unit 2," dated April 27, 1981 4.5 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977 4.6 DOE/TIC-27601, Atmospheric Science and Power Reduction 4.7 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-50 4.8 PDMS-SAR CY-TM-170-300 Revision 3 Page 97 of 209 PART III EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES CY-TM-170-300 Revision 3 Page 98 of 209 1.0 LIQUID EFFLUENT MONITORS 1.1 TMI-1 and TMI-2 Liquid Radiation Monitor Set Points The liquid effluent off-line monitors are set such that the concentration(s) of radionuclides in the liquid effluents will not exceed ten times the concentrations specified in 10 CFR 20, Appendix B Table 2, Col 2. Table 1.1 lists the Liquid Effluent Release Points and their parameters; Figure 1.1 provides a Liquid Release Pathway Diagram.To meet the above limit, the alarm/trip set points for liquid effluent monitors and flow measuring devices are set in accordance with the following equation:* f< C (eq 1.1)F+f -Where: C = ten times the effluent concentration of 10 CFR 20 for the site, in giCi/ml.c = the set point, in giCi/ml, of the liquid effluent monitor measuring the radioactivity concentration in the effluent line prior to dilution and release.The set point is inversely proportional to the maximum volumetric flow of the effluent line and proportional to the minimal volumetric flow of the dilution stream plus the effluent stream. The alert set point value is set to ensure that advance warning occurs prior to exceeding any limits. The high alarm set point value is such that if it were exceeded, it would result in concentrations exceeding ten times the 10 CFR 20 concentrations for the unrestricted area.f = flow set point as measured at the radiation monitor location, in volume per unit time, but in the same units as F below.F = flow rate of dilution water measured prior to the release point, in volume per unit time.The set point concentration is reduced such that concentration contributions from multiple release points would not combine to exceed ten times 10 CFR 20 concentrations.
CY-TM-170-300 Revision 3Page 94 of 209TABLE 3.2-2 Notation (Cont'd)b. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:
The set point concentration is converted to set point scale units using appropriate radiation monitor calibration factors.This section of the ODCM is implemented by the Radiation Monitor System Set Points procedure and, for batch releases, the Releasing Radioactive Liquid Waste procedure.
Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99,Cs-1 34, Cs-1 37, Ce-141 and Ce-1 44 for particulate emissions.
CY-TM-1 70-300 Revision 3 Page 99 of 209 1.2 TMI Liquid Effluent Release Points and Liquid Radiation Monitor Data TMI-1 has two required liquid radiation monitors.
This list does notmean that only these nuclides are to be detected and reported.
These are RM-L6 and RM-L12.These liquid release point radiation monitors and sample points are shown in Table 1.1. (The TMI outfall radiation monitor, RM-L7, is also listed for information only.)TMI-2 does not have any required liquid radiation monitors, but does utilize RM-L12, and RM-L7 for release of liquid waste.1.2.1 RM-L6 RM-L6 is an off-line system, monitoring radioactive batch discharges from the TMI-1 liquid radwaste system (see Figure 1.1). These batch releases are sampled and analyzed per site procedures prior to release.The release rate is based on releasing one of two Waste Evaporator Condensate Storage Tanks (WECST) at a flow which will add less than 10%, of ten times the 10 CFR 20 concentrations  
Other peakswhich are measurable and identifiable, together with the above nuclides, shallalso be identified and reported.
[20% for H-3] to radionuclide concentrations in the unrestricted area, including conservative default values for Sr-89, Sr-90, and Fe-55.The release flow rate used is the most restrictive of two flow rates calculated for each liquid batch release, per the approved plant procedure.
Nuclides which are below the LLD for theanalyses shall be reported as "less than" the nuclide's LLD and shall not bereported as being present at the LLD level for that nuclide.
Two Dilution Factors (DF) are calculated to ultimately calculate the batch release flow rate. These two DF's are calculated to insure each radionuclide released to the unrestricted area is less than 10 percent of ten times the 10CFR20 radionuclide concentrations, (20% for H-3), and to ensure each liquid batch release boron concentration to the river will not exceed 0.7 ppm.The maximum release flow rate is then calculated by dividing the most restrictive (largest)
The "less than"values shall not be used in the required dose calculations.
DF into 90 percent of the current dilution flow rate of the Mechanical Draft Cooling Tower (MDCT). This conservative flow rate is then multiplied by 0.9 for the allowable flow rate.* Calculation of the 10CFR20 concentration DF: DFI = :-Y (SA 1) -(10% [20% for H-3] often times the IOCFR20 concentration)
CY-TM-170-300 Revision 3Page 95 of 2093.2.3 Total Radioactive Effluents 3.2.3.1 Dose Calculation 3.2.3.1.1 Cumulative annual dose contributions from liquidand gaseous effluents shall be determined inaccordance with Surveillances 3.2.1.2.1, 3.2.2.2.1, and 3.2.2.3.1, including direct radiation contributions from the Unit and from outside storage tanks, and inaccordance with the methodology contained in theODCM.
CY-TM-1 70-300Revision 3Page 96 of 2094.0 PART II REFERENCES 4.1 NUREG-0683, "Final Programmatic Environmental Impact Statement related todecontamination and disposal of radioactive wastes resulting from March 28,1979, accident Three Mile Island Nuclear Station, Unit 2," March 1981, and itssupplements.
4.2 TMI-2 PDMS Technical Specifications, attached to Facility License No. DPR-734.3 Title 10, Code of Federal Regulations, "Energy"4.4 "Statement of Policy Relative to the NRC Programmatic Environmental ImpactStatement on the Cleanup of Three Mile Island Unit 2," dated April 27, 19814.5 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from RoutineReleases of Reactor Effluents for the Purpose of Evaluating Compliance with 10CFR Part 50, Appendix I," Revision 1, October 19774.6 DOE/TIC-27601, Atmospheric Science and Power Reduction 4.7 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-504.8 PDMS-SAR CY-TM-170-300 Revision 3Page 97 of 209PART IIIEFFLUENT DATA AND CALCULATIONAL METHODOLOGIES CY-TM-170-300 Revision 3Page 98 of 2091.0 LIQUID EFFLUENT MONITORS1.1 TMI-1 and TMI-2 Liquid Radiation Monitor Set PointsThe liquid effluent off-line monitors are set such that the concentration(s) ofradionuclides in the liquid effluents will not exceed ten times the concentrations specified in 10 CFR 20, Appendix B Table 2, Col 2. Table 1.1 lists the LiquidEffluent Release Points and their parameters; Figure 1.1 provides a LiquidRelease Pathway Diagram.To meet the above limit, the alarm/trip set points for liquid effluent monitors andflow measuring devices are set in accordance with the following equation:
* f< C (eq 1.1)F+f -Where:C = ten times the effluent concentration of 10 CFR 20 for the site, in giCi/ml.c = the set point, in giCi/ml, of the liquid effluent monitor measuring theradioactivity concentration in the effluent line prior to dilution and release.The set point is inversely proportional to the maximum volumetric flow of theeffluent line and proportional to the minimal volumetric flow of the dilutionstream plus the effluent stream. The alert set point value is set to ensurethat advance warning occurs prior to exceeding any limits. The high alarmset point value is such that if it were exceeded, it would result inconcentrations exceeding ten times the 10 CFR 20 concentrations for theunrestricted area.f = flow set point as measured at the radiation monitor location, in volume perunit time, but in the same units as F below.F = flow rate of dilution water measured prior to the release point, in volume perunit time.The set point concentration is reduced such that concentration contributions frommultiple release points would not combine to exceed ten times 10 CFR 20concentrations.
The set point concentration is converted to set point scale unitsusing appropriate radiation monitor calibration factors.This section of the ODCM is implemented by the Radiation Monitor System SetPoints procedure and, for batch releases, the Releasing Radioactive LiquidWaste procedure.
CY-TM-1 70-300Revision 3Page 99 of 2091.2 TMI Liquid Effluent Release Points and Liquid Radiation Monitor DataTMI-1 has two required liquid radiation monitors.
These are RM-L6 and RM-L12.These liquid release point radiation monitors and sample points are shown inTable 1.1. (The TMI outfall radiation  
: monitor, RM-L7, is also listed for information only.)TMI-2 does not have any required liquid radiation  
: monitors, but does utilizeRM-L12, and RM-L7 for release of liquid waste.1.2.1 RM-L6RM-L6 is an off-line system, monitoring radioactive batch discharges from the TMI-1 liquid radwaste system (see Figure 1.1). These batchreleases are sampled and analyzed per site procedures prior to release.The release rate is based on releasing one of two Waste Evaporator Condensate Storage Tanks (WECST) at a flow which will add less than10%, of ten times the 10 CFR 20 concentrations  
[20% for H-3] toradionuclide concentrations in the unrestricted area, including conservative default values for Sr-89, Sr-90, and Fe-55.The release flow rate used is the most restrictive of two flow ratescalculated for each liquid batch release, per the approved plantprocedure.
Two Dilution Factors (DF) are calculated to ultimately calculate the batchrelease flow rate. These two DF's are calculated to insure eachradionuclide released to the unrestricted area is less than 10 percent often times the 10CFR20 radionuclide concentrations, (20% for H-3), andto ensure each liquid batch release boron concentration to the river willnot exceed 0.7 ppm.The maximum release flow rate is then calculated by dividing the mostrestrictive (largest)
DF into 90 percent of the current dilution flow rate ofthe Mechanical Draft Cooling Tower (MDCT). This conservative flowrate is then multiplied by 0.9 for the allowable flow rate.* Calculation of the 10CFR20 concentration DF:DFI = :-Y (SA1) -(10% [20% for H-3] often times the IOCFR20concentration)
SA = Specific Activity of each identified radionuclide
SA = Specific Activity of each identified radionuclide
* Calculation of Boron DF:DF2= Actual Tank Boron Concentration  
* Calculation of Boron DF: DF 2= Actual Tank Boron Concentration  
+ 0.7.
+ 0.7.
CY-TM-170-300 Revision 3Page 100 of 209Maximum release flow rate calculation:
CY-TM-170-300 Revision 3 Page 100 of 209 Maximum release flow rate calculation:
Max Flow = [(MDCT flow gpm
Max Flow = [(MDCT flow gpm
* 0.9) -(Most Restrictive DF)] *0.9The dilution flow rate used is the current flow rate at the site. Theminimum dilution flow rate is 5000 gpm per the TMI-1 FSAR. Thisensures this batch release will meet the following equation.
* 0.9) -(Most Restrictive DF)] *0.9 The dilution flow rate used is the current flow rate at the site. The minimum dilution flow rate is 5000 gpm per the TMI-1 FSAR. This ensures this batch release will meet the following equation.YX(CI/Xi)  
YX(CI/Xi)  
+ (CH-3/2XH-3)  
+ (CH-3/2XH-3)  
< 0.1, (eq 1.2)Where: Ci = diluted concentration of the ith radionuclide, other than H-3Xi= Ten times the concentration for that radionuclide in theunrestricted area (10 CFR 20, App. B, Table 2, Col. 2). Avalue of 3E-3 jtCi/ml for dissolved and entrained noble gasesshall be used.CH.3 = diluted concentration of H-3XH-3 = Ten times the concentration for H-3 in the restricted area (10CFR 20, App. B, Table 2, Col. 2).The set points for RM-L6 are based on the maximum release rate (30gpm), a minimum dilution flow (5000 gpm), and 25% of ten times the1OCFR20 concentration for Cs-1 37, which is the most limitingradionuclide at a concentration of 1.OE-5 uCi/ml. These inputs are usedin Equation 1.1 to determine the RM-L-6 High Alarm setpoint for allradionuclides being released.
< 0.1, (eq 1.2)Where: Ci = diluted concentration of the ith radionuclide, other than H-3 Xi= Ten times the concentration for that radionuclide in the unrestricted area (10 CFR 20, App. B, Table 2, Col. 2). A value of 3E-3 jtCi/ml for dissolved and entrained noble gases shall be used.CH.3 = diluted concentration of H-3 XH-3 = Ten times the concentration for H-3 in the restricted area (10 CFR 20, App. B, Table 2, Col. 2).The set points for RM-L6 are based on the maximum release rate (30 gpm), a minimum dilution flow (5000 gpm), and 25% of ten times the 1OCFR20 concentration for Cs-1 37, which is the most limiting radionuclide at a concentration of 1.OE-5 uCi/ml. These inputs are used in Equation 1.1 to determine the RM-L-6 High Alarm setpoint for all radionuclides being released.
A high alarm on RM-L-6 will close valveWDL-V-257 and terminate any WECST releases to the environment.
A high alarm on RM-L-6 will close valve WDL-V-257 and terminate any WECST releases to the environment.
1.2.2 RM-L12RM-L12 is an off-line system, monitoring periodic combined releasesfrom the Industrial Waste Treatment System/Industrial Waste Filtration System (IWTS/IWFS).
1.2.2 RM-L12 RM-L12 is an off-line system, monitoring periodic combined releases from the Industrial Waste Treatment System/Industrial Waste Filtration System (IWTS/IWFS).
The input to IWTS/IWFS originates in TMI-2sumps, (see Figures 1.1 and 1.2) and the TMI-1 Turbine Building sump(see Figure 1.1). The set points are based on the maximum release ratefrom both IWTS and IWFS simultaneously, (see Figure 1.1) a minimumdilution flow rate, and 50% of ten times the 10CFR20 concentration forCs-1 37, which is the most limiting radionuclide at a concentration of1E-5 &#xfd;tCi/ml.
The input to IWTS/IWFS originates in TMI-2 sumps, (see Figures 1.1 and 1.2) and the TMI-1 Turbine Building sump (see Figure 1.1). The set points are based on the maximum release rate from both IWTS and IWFS simultaneously, (see Figure 1.1) a minimum dilution flow rate, and 50% of ten times the 10CFR20 concentration for Cs-1 37, which is the most limiting radionuclide at a concentration of 1E-5 &#xfd;tCi/ml. These inputs are used in equation 1.1 to determine the RM-L12 High Alarm set point for all radionuclides being released.
These inputs are used in equation 1.1 to determine theRM-L12 High Alarm set point for all radionuclides being released.
A high alarm on RM-L12 will close IWTS and IWFS release valves and trip release pumps to stop the release.
Ahigh alarm on RM-L12 will close IWTS and IWFS release valves and triprelease pumps to stop the release.
CY-TM-1 70-300 Revision 3 Page 101 of 209 1.2.3 RM-L1O RM-L1O was a Nal detector submerged in the TMI-1 Turbine Building Sump. This detector has been removed from service.1.2.4 RM-L7 RM-L7 is not an ODCM required liquid radiation monitor. RM-L7 is an off-line system, monitoring the TMI outfall to the Susquehanna River (see Figures 1.1 and 1.2). This monitor is the final radiation monitor for TMI-1 and TMI-2 normal liquid effluent releases.1.3 Control of Liquid Releases TMI liquid effluent releases are controlled to less than ten times the 1OCFR20 concentrations by limiting the percentage of this limit allowable from the two TMI liquid release points. RM-L6 and effluent sampling limit batch releases to less than or equal to 25% for all radionuclides, and RM-L12 and effluent sampling limit releases from TMI-1 and TMI-2 to less than or equal to 50% for Cs-1 37.These radiation monitor set points also include built in meter error factors to further ensure that TMI liquid effluent releases are less than ten times the 1OCFR20 concentrations to the environment.
CY-TM-1 70-300Revision 3Page 101 of 2091.2.3 RM-L1ORM-L1O was a Nal detector submerged in the TMI-1 Turbine BuildingSump. This detector has been removed from service.1.2.4 RM-L7RM-L7 is not an ODCM required liquid radiation monitor.
The radioactivity content of each batch of radioactive liquid waste is determined prior to release by sampling and analysis in accordance with ODCM Part I Table 3.2-1 or ODCM Part II, Table 3.2-1. The results of analyses are used with the calculational methods in Section 1.1, to assure that the concentration at the point of release is maintained within the ODCM Part I Control 2.2.1.1, and ODCM Part II Control 2.2.1.1.Post-release analysis of samples composited from batch releases are performed in accordance with ODCM Part I Table 3.2-1 or ODCM Part II Table 3.2-1. The results of the previous post-release analysis shall be used with the calculational methods in the ODCM to assure that the concentrations at the point of release were maintained within the ODCM Part I Control 2.2.1.1, and ODCM Part II Control 2.2.1.1.The radioactivity concentration of liquids discharged from continuous release points are determined by collection and analysis of samples in accordance with ODCM Part I Table 3.2-1, or ODCM Part II Table 3.2-1. The results of the analysis are used with the calculational methods of the ODCM to assure that the concentration at the point of release is maintained within the ODCM Part I Control 2.2.1.1, and ODCM Part II Control 2.2.1.1.
RM-L7 is anoff-line system, monitoring the TMI outfall to the Susquehanna River(see Figures 1.1 and 1.2). This monitor is the final radiation monitor forTMI-1 and TMI-2 normal liquid effluent releases.
CY-TM-170-300 Revision 3 Page 102 of 209 TABLE 1.1 TMI Liquid Release Point and Liquid Radiation Monitor Data RELEASE LIQUID RADIATION LIQUID RELEASE TERMINATION MONITOR POINT (Maximum DISCHARGE FLOW INTERLOCK (DETECTOR)
1.3 Control of Liquid ReleasesTMI liquid effluent releases are controlled to less than ten times the 1OCFR20concentrations by limiting the percentage of this limit allowable from the two TMIliquid release points. RM-L6 and effluent sampling limit batch releases to lessthan or equal to 25% for all radionuclides, and RM-L12 and effluent samplinglimit releases from TMI-1 and TMI-2 to less than or equal to 50% for Cs-1 37.These radiation monitor set points also include built in meter error factors tofurther ensure that TMI liquid effluent releases are less than ten times the1OCFR20 concentrations to the environment.
LOCATION Volume) RECORDER (YES/NO) VALVES RM-L6 281' Elevation WECST Batch YES (Nal) TMI-1 Auxiliary Bldg Releases (8000 gal.) WDL-V257 RM-L7 South end of TMI-1 Station Discharge YES (Nal) MDCT TMI-1 and SR-FT-146 WDL-V257** TMI-2, *WDL-R-1 311 YES IWTS/IWFS IW-V73, RM-L12 IWFS Building NW Continuous Releases IW-FT-342/
The radioactivity content of each batch of radioactive liquid waste is determined prior to release by sampling and analysis in accordance with ODCM Part I Table3.2-1 or ODCM Part II, Table 3.2-1. The results of analyses are used with thecalculational methods in Section 1.1, to assure that the concentration at the pointof release is maintained within the ODCM Part I Control 2.2.1.1, and ODCM PartII Control 2.2.1.1.Post-release analysis of samples composited from batch releases are performed in accordance with ODCM Part I Table 3.2-1 or ODCM Part II Table 3.2-1. Theresults of the previous post-release analysis shall be used with the calculational methods in the ODCM to assure that the concentrations at the point of releasewere maintained within the ODCM Part I Control 2.2.1.1, and ODCM Part IIControl 2.2.1.1.The radioactivity concentration of liquids discharged from continuous releasepoints are determined by collection and analysis of samples in accordance withODCM Part I Table 3.2-1, or ODCM Part II Table 3.2-1. The results of theanalysis are used with the calculational methods of the ODCM to assure that theconcentration at the point of release is maintained within the ODCM Part IControl 2.2.1.1, and ODCM Part II Control 2.2.1.1.
CY-TM-170-300 Revision 3Page 102 of 209TABLE 1.1TMI Liquid Release Point and Liquid Radiation Monitor DataRELEASELIQUID RADIATION LIQUID RELEASE TERMINATION MONITOR POINT (Maximum DISCHARGE FLOW INTERLOCK (DETECTOR)
LOCATION Volume) RECORDER (YES/NO)
VALVESRM-L6 281' Elevation WECST Batch YES(Nal) TMI-1 Auxiliary Bldg Releases (8000 gal.) WDL-V257RM-L7 South end of TMI-1 Station Discharge YES(Nal) MDCT TMI-1 and SR-FT-146 WDL-V257** TMI-2, *WDL-R-1 311YESIWTS/IWFS IW-V73,RM-L12 IWFS Building NW Continuous Releases IW-FT-342/
IW-P16,17,18 (Nal) Corner (300,000/
IW-P16,17,18 (Nal) Corner (300,000/
IW-FT-373 80,000 gal.) IW-V279,I_ IW-P29,30
IW-FT-373 80,000 gal.) IW-V279, I_ IW-P29,30* WDL-R-1311 has been flanged off as a TMI-2 liquid outfall.** RM-L7 is not an ODCM required liquid radiation monitor.
* WDL-R-1311 has been flanged off as a TMI-2 liquid outfall.** RM-L7 is not an ODCM required liquid radiation monitor.
CY-TM-170-300 Revision 3 Page 103 of 209 TABLE 1.2 TMI-2 Sump Capacities Total Capacity Gallons Sump Gallons per Inch Turbine Building Sump 1346 22.43 Circulating Water Pump House Sump 572 10.59 Control Building Area Sump 718 9.96 Tendon Access Galley Sump 538 9.96 Control to Service Building Sump 1346 22.43 Contaminated Drain Tank Room Sump 135 3.80 Chlorinator House Sump ........Water Treatment Sump** 1615 22.43 Air Intake Tunnel Normal Sump 700 ----Air Intake Tunnel Emergency Sump 100000 766.00 Condensate Polisher Sump* 2617 62.31 Sludge Collection Sump** 1106 26.33 Heater Drain Sump ----.....Solid Waste Staging Facility Sump 1476 24.00 Auxiliary Building Sump 10102 202.00 Decay Heat Vault Sump 479 10.00 Building Spray Vault Sump 479 10.00* Condensate Polisher Sump is deactivated and in PDMS condition.
CY-TM-170-300 Revision 3Page 103 of 209TABLE 1.2TMI-2 Sump Capacities TotalCapacity GallonsSump Gallons per InchTurbine Building Sump 1346 22.43Circulating Water Pump House Sump 572 10.59Control Building Area Sump 718 9.96Tendon Access Galley Sump 538 9.96Control to Service Building Sump 1346 22.43Contaminated Drain Tank Room Sump 135 3.80Chlorinator House Sump ........Water Treatment Sump** 1615 22.43Air Intake Tunnel Normal Sump 700 ----Air Intake Tunnel Emergency Sump 100000 766.00Condensate Polisher Sump* 2617 62.31Sludge Collection Sump** 1106 26.33Heater Drain Sump ----.....
Solid Waste Staging Facility Sump 1476 24.00Auxiliary Building Sump 10102 202.00Decay Heat Vault Sump 479 10.00Building Spray Vault Sump 479 10.00* Condensate Polisher Sump is deactivated and in PDMS condition.
** The Water Treatment and Sludge Collection Sumps will be deactivated for PDMS.
** The Water Treatment and Sludge Collection Sumps will be deactivated for PDMS.
CY-TM-1 70-300Revision 3Page 104 of 209FIGURE 1-1TMI-1 Liquid Effluent PathwaysPage 1 of 1 CY-TM-1 70-300Revision 3Page 105 of 209FIGURE 1.2TMI-2 Liquid Effluent PathwaysCONTROL CONTROL &BUILDING SERVICESUMP AREA SUMPINDUSTRIAL WASTETREATMENT SYSTEMC -- COMPOSITE SAMPLER CY-TM-1 70-300Revision 3Page 106 of 2092.0 LIQUID EFFLUENT DOSE ASSESSMENT 2.1 Liquid Effluents  
CY-TM-1 70-300 Revision 3 Page 104 of 209 FIGURE 1-1 TMI-1 Liquid Effluent Pathways Page 1 of 1 CY-TM-1 70-300 Revision 3 Page 105 of 209 FIGURE 1.2 TMI-2 Liquid Effluent Pathways CONTROL CONTROL &BUILDING SERVICE SUMP AREA SUMP INDUSTRIAL WASTE TREATMENT SYSTEM C -- COMPOSITE SAMPLER CY-TM-1 70-300 Revision 3 Page 106 of 209 2.0 LIQUID EFFLUENT DOSE ASSESSMENT 2.1 Liquid Effluents  
-10 CFR 50 Appendix IThe dose from liquid effluents results from the consumption of fish and drinkingwater. The location of the nearest potable water intake is PP&L Brunner IslandSteam Electric Station located downstream of TMI. The use of the flow of theSusquehanna River as the dilution flow is justified based on the complete mixingin the river prior to the first potable water supply, adequately demonstrated byflume tracer die studies and additional liquid effluent release studies conducted using actual TMI-1 tritium releases.
-10 CFR 50 Appendix I The dose from liquid effluents results from the consumption of fish and drinking water. The location of the nearest potable water intake is PP&L Brunner Island Steam Electric Station located downstream of TMI. The use of the flow of the Susquehanna River as the dilution flow is justified based on the complete mixing in the river prior to the first potable water supply, adequately demonstrated by flume tracer die studies and additional liquid effluent release studies conducted using actual TMI-1 tritium releases.
Other pathways contribute negligibly atThree Mile Island. The dose contribution from all radionuclides in liquid effluents released to the unrestricted area is calculated using the following expression:
Other pathways contribute negligibly at Three Mile Island. The dose contribution from all radionuclides in liquid effluents released to the unrestricted area is calculated using the following expression:
Dose j (At) X () X AW ij X- + (AF ij X f X 1 (eq 2.1)Doej. AtX(C) LAWJFR) FD DFWhere:Dose j = the cumulative dose commitment to the total body or any organ, j, fromthe liquid effluents for the total time period, in mrem.At = the length of the time period of actual releases, over which Ci and f areaveraged for all liquid releases, in hours.C = the average concentration of radionuclide, i, in undiluted liquid effluentduring time period At from any liquid release, in &#xfd;LCi/ml.NOTE: For Fe-55, Sr-89, Sr-90, prior to batch releases conservative concentration values will be used in the initial dose calculation based on similar past plant conditions.
Dose j (At) X () X AW ij X- + (AF ij X f X 1 (eq 2.1)Doej. AtX(C) LAWJFR) FD DF Where: Dose j = the cumulative dose commitment to the total body or any organ, j, from the liquid effluents for the total time period, in mrem.At = the length of the time period of actual releases, over which Ci and f are averaged for all liquid releases, in hours.C = the average concentration of radionuclide, i, in undiluted liquid effluent during time period At from any liquid release, in &#xfd;LCi/ml.NOTE: For Fe-55, Sr-89, Sr-90, prior to batch releases conservative concentration values will be used in the initial dose calculation based on similar past plant conditions.
LLD values are not usedin dose calculations.
LLD values are not used in dose calculations.
f = undiluted liquid waste flow, in gpm.FD = plant dilution water flowrate during the period of release, in gpmFR = actual river flowrate during the period of release or average riverlowrate for the month the release is occurring, in gpm.DF = dilution factor as a result of mixing effects in the near field of thedischarge structure of 0.2 (NUREG 0133) or taken to be 5 based on theinverse of 0.2.AWij and AFij = the site-related ingestion dose commitment factor to the totalbody or any organ, j, for each identified principle gamma andbeta emitter, in mrem/hr per pCi/ml. AW is the factor for thewater pathway and AF is the factor for the fish pathway.
f = undiluted liquid waste flow, in gpm.FD = plant dilution water flowrate during the period of release, in gpm FR = actual river flowrate during the period of release or average river lowrate for the month the release is occurring, in gpm.DF = dilution factor as a result of mixing effects in the near field of the discharge structure of 0.2 (NUREG 0133) or taken to be 5 based on the inverse of 0.2.AWij and AFij = the site-related ingestion dose commitment factor to the total body or any organ, j, for each identified principle gamma and beta emitter, in mrem/hr per pCi/ml. AW is the factor for the water pathway and AF is the factor for the fish pathway.
CY-TM-1 70-300Revision 3Page 107 of 209Values for AWij are determined by the following equation:
CY-TM-1 70-300 Revision 3 Page 107 of 209 Values for AWij are determined by the following equation: AWij = (1.14E5) x (Uw) x (DFij) (eq 2.2)Where: 1.14E5 = (1.0E6 pCilpjCi) x (1.0E3 mi/kg) + (8760 hrlyr)Uw = Water consumption rate for adult is 730 kg/yr (Reg. Guide 1.109, Rev. 1).DFij = ingestion dose conversion factor for radionuclide, i, for adults total body and for "worst case" organ, j, in mrem/pCi, from Table 2.1 (Reg. Guide 1.109)Values for AFij are determined by the following equation: AFij = (1.14E5) x (Uf) x (DFij) x (BFi) (eq 2.2.2)where: 1.14E5 = defined above Uf = adult fish consumption, assumed to be 21 kg/yr (Reg. Guide 1.109, Rev. 1).DFij = ingestion dose conversion factor for radionuclide, i, for adult total body and for "worst case" organ, j, in mrem/pCi, from Table 2.1 (Reg. Guide 1.109, Rev. 1).BFi = Bioaccumulation factor for radionuclide, i, in fish, in pCi/kg per pCi/L from Table 2.2 (Reg. Guide 1.109, Rev. 1).2.2 TMI Liquid Radwaste System Dose Calcs Once Per Month ODCM Part I Control 2.2.1.3 and TMI-2 PDMS Tech Spec Section 6.7.4.a.6 requires that appropriate portions of the liquid radwaste treatment system shall be used to reduce the radioactive materials in liquid wastes prior to their discharge when the monthly projected doses due to the liquid effluent releases from each unit to unrestricted areas would exceed 0.06 mrem to the total body or 0.2 mrem to any organ in any calendar month. The following calculational method is provided for performing this dose projection.
AWij = (1.14E5) x (Uw) x (DFij) (eq 2.2)Where:1.14E5 = (1.0E6 pCilpjCi) x (1.0E3 mi/kg) + (8760 hrlyr)Uw = Water consumption rate for adult is 730 kg/yr (Reg. Guide 1.109, Rev. 1).DFij = ingestion dose conversion factor for radionuclide, i, for adults total bodyand for "worst case" organ, j, in mrem/pCi, from Table 2.1(Reg. Guide 1.109)Values for AFij are determined by the following equation:
At least once per month, the total dose from all liquid releases for the quarter-to-date will be divided by the number of days into the quarter and multiplied by 31. Also, this dose projection shall include the estimated dose due to any anticipated unusual releases during the period for which the projection is made. If this projected dose exceeds 0.06 mrem total body or 0.2 mrem any organ, appropriate portions of the Liquid Radwaste Treatment System, as CY-TM-170-300 Revision 3 Page 108 of 209 defined in Section 3.1, shall be used to reduce radioactivity levels prior to release.At the discretion of the ODCM Specialist, time periods other than the current quarter-to-date may be used to project doses if the dose per day in the current quarter-to-date is not believed to be representative of the dose per day projected for the next month.2.3 Alternative Liquid Dose Calculational Methodology As an alternative, models in, or based upon, those presented in Regulatory Guide 1.109 (Rev. 1) may be used to make a comprehensive dose assessment.
AFij = (1.14E5) x (Uf) x (DFij) x (BFi) (eq 2.2.2)where:1.14E5 = defined aboveUf = adult fish consumption, assumed to be 21 kg/yr (Reg. Guide 1.109,Rev. 1).DFij = ingestion dose conversion factor for radionuclide, i, for adult total bodyand for "worst case" organ, j, in mrem/pCi, from Table 2.1(Reg. Guide 1.109, Rev. 1).BFi = Bioaccumulation factor for radionuclide, i, in fish, in pCi/kg per pCi/Lfrom Table 2.2 (Reg. Guide 1.109, Rev. 1).2.2 TMI Liquid Radwaste System Dose Calcs Once Per MonthODCM Part I Control 2.2.1.3 and TMI-2 PDMS Tech Spec Section 6.7.4.a.6 requires that appropriate portions of the liquid radwaste treatment system shallbe used to reduce the radioactive materials in liquid wastes prior to theirdischarge when the monthly projected doses due to the liquid effluent releasesfrom each unit to unrestricted areas would exceed 0.06 mrem to the total body or0.2 mrem to any organ in any calendar month. The following calculational method is provided for performing this dose projection.
Default parameter values from Reg. Guide 1.109 (Rev. 1) and/or actual site specific data are used where applicable.
At least once per month, the total dose from all liquid releases for thequarter-to-date will be divided by the number of days into the quarter andmultiplied by 31. Also, this dose projection shall include the estimated dose dueto any anticipated unusual releases during the period for which the projection ismade. If this projected dose exceeds 0.06 mrem total body or 0.2 mrem anyorgan, appropriate portions of the Liquid Radwaste Treatment System, as CY-TM-170-300 Revision 3Page 108 of 209defined in Section 3.1, shall be used to reduce radioactivity levels prior torelease.At the discretion of the ODCM Specialist, time periods other than the currentquarter-to-date may be used to project doses if the dose per day in the currentquarter-to-date is not believed to be representative of the dose per day projected for the next month.2.3 Alternative Liquid Dose Calculational Methodology As an alternative, models in, or based upon, those presented in Regulatory Guide 1.109 (Rev. 1) may be used to make a comprehensive dose assessment.
As an alternative dose calculational methodology TMI calculates doses using SEEDS (simplified environmental effluent dosimetry system).The onsite and SEEDS calculational models use actual liquid release data with actual monthly Susquehanna River flow data to assess the dispersion of effluents in the river.
Default parameter values from Reg. Guide 1.109 (Rev. 1) and/or actual sitespecific data are used where applicable.
CY-TM-1 70-300 Revision 3 Page 109 of 209 TABLE 2.1 Liquid Dose Conversion Factors (DCF): DF 1 j Page 1 of 3 Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLI H 3 NO DATA 1.05E-07 1.05E-07 1.05E-07 1.05E-07 1.05E-07 1.05E-07 C 14 2.84E-06 5.68E-07 5.68E-07 5.68E-07 5.68E-07 5.68E-07 5.68E-07 NA 24 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06 CR.51 NO DATA NO DATA 2.66E-09 1.59E-09 5.86E-10 3.53E-09 6.69E-07 MN 54 NO DATA 4.57E-06 8.72E-07 NO DATA 1.36E-06 NO DATA 1.40E-05............... ....... .. .. .. ...........  
As an alternative dose calculational methodology TMI calculates doses usingSEEDS (simplified environmental effluent dosimetry system).The onsite and SEEDS calculational models use actual liquid release data withactual monthly Susquehanna River flow data to assess the dispersion of effluents in the river.
CY-TM-1 70-300Revision 3Page 109 of 209TABLE 2.1Liquid Dose Conversion Factors (DCF): DF1jPage 1 of 3Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)
NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLIH 3 NO DATA 1.05E-07 1.05E-07 1.05E-07 1.05E-07 1.05E-07 1.05E-07C 14 2.84E-06 5.68E-07 5.68E-07 5.68E-07 5.68E-07 5.68E-07 5.68E-07NA 24 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06CR.51 NO DATA NO DATA 2.66E-09 1.59E-09 5.86E-10 3.53E-09 6.69E-07MN 54 NO DATA 4.57E-06 8.72E-07 NO DATA 1.36E-06 NO DATA 1.40E-05............... ....... .. .. .. ...........  
..... ..........  
..... ..........  
... ... .........  
... ... ......... .. .. .................  
.. .. .................  
..... .. ..........  
..... .. ..........  
.. ...... .............  
.. ...... .............  
......... ....MN 56 NO DATA 1.151E-07 2.04E-08 NO DATA 1.46E-07 NO DATA 3.67E-06FE 55 2.75E-06 1.90E-06 4.43E-07 NO DATA NO DATA 1.06E-06 1.09E-06FE 59 4.34E-06 1.02E-05 3.91E-06 NO DATA NO DATA 2.85E-06 3.40E-05CO-58 NO DATA 7.45E-07 1.67E-06 NO DATA NO DATA NO DATA 1.51E-05CO 60 NO DATA 2.14E-06 4.72E-06 NO DATA NO DATA NO DATA 4.02E-05NI 63 1.30E-04 9.011E-06 4.36E-06 NO DATA NO DATA NO DATA 1.88E-06.............  
......... ....MN 56 NO DATA 1.151E-07 2.04E-08 NO DATA 1.46E-07 NO DATA 3.67E-06 FE 55 2.75E-06 1.90E-06 4.43E-07 NO DATA NO DATA 1.06E-06 1.09E-06 FE 59 4.34E-06 1.02E-05 3.91E-06 NO DATA NO DATA 2.85E-06 3.40E-05 CO-58 NO DATA 7.45E-07 1.67E-06 NO DATA NO DATA NO DATA 1.51E-05 CO 60 NO DATA 2.14E-06 4.72E-06 NO DATA NO DATA NO DATA 4.02E-05 NI 63 1.30E-04 9.011E-06 4.36E-06 NO DATA NO DATA NO DATA 1.88E-06.............  
.........................................................................................................  
.........................................................................................................  
..... ....................................................
..... ....................................................
NI 65 5.28E-07 6.86E-08 3.13E-08 NO DATA NO DATA NO DATA 1.74E-06CU 64 NO DATA 8.33E-08 3.91 E-08 NO DATA 2.1OE-07 NO DATA 7.1OE-06ZN 65 4.84E-06 1.54E-05 6.96E-06 NO DATA 1.03E-05 NO DATA 9.70E-06.. .............................................................................................................................................................................
NI 65 5.28E-07 6.86E-08 3.13E-08 NO DATA NO DATA NO DATA 1.74E-06 CU 64 NO DATA 8.33E-08 3.91 E-08 NO DATA 2.1OE-07 NO DATA 7.1OE-06 ZN 65 4.84E-06 1.54E-05 6.96E-06 NO DATA 1.03E-05 NO DATA 9.70E-06.. .............................................................................................................................................................................
ZN 69 1.03E-08 1.97E-08 1.37E-09 NO DATA 1.28E-08 NO DATA 2.96E-09BR 83 NO DATA NO DATA 4.02E-08 NO DATA NO DATA NO DATA 5.79E-08BR 84 NO DATA NO DATA 5.21E-08 NO DATA NO DATA NO DATA 4.09E-13..............  
ZN 69 1.03E-08 1.97E-08 1.37E-09 NO DATA 1.28E-08 NO DATA 2.96E-09 BR 83 NO DATA NO DATA 4.02E-08 NO DATA NO DATA NO DATA 5.79E-08 BR 84 NO DATA NO DATA 5.21E-08 NO DATA NO DATA NO DATA 4.09E-13..............  
..............  
..............  
.............  
.............  
Line 476: Line 352:
..............  
..............  
.............
.............
BR-85 NO DATA NO DATA 2.14E-09 NO DATA NO DATA NO DATA LT E-24RB 86 NO DATA 2.11E-05 9.83E-06 NO DATA NO DATA NO DATA 4.16E-06RB 88 NO DATA 6.05E-08 3.21 E-08 NO DATA NO DATA NO DATA 8.36E-19RB.89 NO DATA 4.01E-08 2.82E-08 NO DATA NO DATA NO DATA 2.33E-21SR 89 3.08E-04 NO DATA 8.84E-06 NO DATA NO DATA NO DATA 4.94E-05SR 90 7.58E-03 NO DATA 1.86E-03 NO DATA NO DATA NO DATA 2.19E-04..R. .1 0-6E- .. -NO DATA' 2.29E-07 NO DATA NO DATA NO DATA 2.70E-05-----------------------------------------
BR-85 NO DATA NO DATA 2.14E-09 NO DATA NO DATA NO DATA LT E-24 RB 86 NO DATA 2.11E-05 9.83E-06 NO DATA NO DATA NO DATA 4.16E-06 RB 88 NO DATA 6.05E-08 3.21 E-08 NO DATA NO DATA NO DATA 8.36E-19 RB.89 NO DATA 4.01E-08 2.82E-08 NO DATA NO DATA NO DATA 2.33E-21 SR 89 3.08E-04 NO DATA 8.84E-06 NO DATA NO DATA NO DATA 4.94E-05 SR 90 7.58E-03 NO DATA 1.86E-03 NO DATA NO DATA NO DATA 2.19E-04..R. .1 0-6E- .. -NO DATA' 2.29E-07 NO DATA NO DATA NO DATA 2.70E-05-----------------------------------------
2;2 9-f *...........---......  
2;2 9-f *...........---......  
...... ..........*- -------SR 92 2.15E-06 NO DATA 9.30E-08 NO DATA NO DATA NO DATA 4.26E-05Y 90 9.62E-09 NO DATA 2.58E-10 NO DATA NO DATA NO DATA 1.02E-04 CY-TM-1 70-300Revision 3Page 110 of 209TABLE 2.1Liquid Dose Conversion Factors (DCF): DF=jPage 2 of 3Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)
...... ..........*- -------SR 92 2.15E-06 NO DATA 9.30E-08 NO DATA NO DATA NO DATA 4.26E-05 Y 90 9.62E-09 NO DATA 2.58E-10 NO DATA NO DATA NO DATA 1.02E-04 CY-TM-1 70-300 Revision 3 Page 110 of 209 TABLE 2.1 Liquid Dose Conversion Factors (DCF): DF=j Page 2 of 3 Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLI Y 91M 9.09E-11 NO DATA 3.52E-12 NO DATA NO DATA NO DATA 2.67E-10 Y 91 1.41 E-07 NO DATA 3.77E-09 NO DATA NO DATA NO DATA 7.76E-05 Y 92 8.45E-10 NO DATA 2.47E-11 NO DATA NO DATA NO DATA 1.48E-05 Y 93 2.68E-09 NO DATA 7.40E-11 NO DATA NO DATA NO DATA 8.50E-05 ZR 95 3.04E-08 9.75E-09 6.60E-09 NO DATA 1.53E-08 NO DATA 3.09E-05 ZR 97 1.68E-09 3.39E-10 1.55E-10 NO DATA 5.12E-10 NO DATA 1.05E-04 NB.95 6.22E-09 3.46E-09 1.86E-09 NO DATA 3.42E-09 NO DATA 2.10E-05 MO 99 NO DATA 4.31E-06 8.20E-07 NO DATA 9.76E-06 NO DATA 9.99E-06 TC 99M 2.47E-10 6.98E-10 8.89E-09 NO DATA 1.06E-08 3.42E-10 4.13E-07.. .............................................................................................................................................................................
NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLIY 91M 9.09E-11 NO DATA 3.52E-12 NO DATA NO DATA NO DATA 2.67E-10Y 91 1.41 E-07 NO DATA 3.77E-09 NO DATA NO DATA NO DATA 7.76E-05Y 92 8.45E-10 NO DATA 2.47E-11 NO DATA NO DATA NO DATA 1.48E-05Y 93 2.68E-09 NO DATA 7.40E-11 NO DATA NO DATA NO DATA 8.50E-05ZR 95 3.04E-08 9.75E-09 6.60E-09 NO DATA 1.53E-08 NO DATA 3.09E-05ZR 97 1.68E-09 3.39E-10 1.55E-10 NO DATA 5.12E-10 NO DATA 1.05E-04NB.95 6.22E-09 3.46E-09 1.86E-09 NO DATA 3.42E-09 NO DATA 2.10E-05MO 99 NO DATA 4.31E-06 8.20E-07 NO DATA 9.76E-06 NO DATA 9.99E-06TC 99M 2.47E-10 6.98E-10 8.89E-09 NO DATA 1.06E-08 3.42E-10 4.13E-07.. .............................................................................................................................................................................
TC 101 2.54E-10 3.66E-10 3.59E-09 NO DATA 6.59E-09 1.87E-10 1.1OE-21 RU 103 1.85E-07 NO DATA 7.97E-08 NO DATA 7.06E-07 NO DATA 2.16E-05 RU 105 1.54E-08 NO DATA 6.08E-09 NO DATA 1.99E-07 NO DATA 9.42E-06 RU 106 2.75E-06 NO DATA 3.48E-07 NO DATA 5.31 E-06 NO DATA 1.78E-04 AG 110M 1.60E-07 1.48E-07 8.79E-08 NO DATA 2.91 E-07 NO DATA 6.04E-05 SB 125 1.79E-06 2.00E-08 4.26E-07 1.82E-09 0.0 1.38E-06 1.97E-05 TE 125M 2.68E-06 9.71 E-07 3.59E-07 8.06E-07 1.09E-05 NO DATA 1.07E-05 TE.127M 6.77E-06 2.42E-06 8.25E-07 1.73E-06 2.75E-05 NO DATA 2.27E-05 TE 127 1.10E-07 3.95E-08 2.38E-08 8.15E-08 4.48E-07 NO DATA 8.68E-06 TE 129M 1.15E-05 4.29E-06 1.82E-06 3.95E-06 4.80E-05 NO DATA 5.79E-05.. .............................................  
TC 101 2.54E-10 3.66E-10 3.59E-09 NO DATA 6.59E-09 1.87E-10 1.1OE-21RU 103 1.85E-07 NO DATA 7.97E-08 NO DATA 7.06E-07 NO DATA 2.16E-05RU 105 1.54E-08 NO DATA 6.08E-09 NO DATA 1.99E-07 NO DATA 9.42E-06RU 106 2.75E-06 NO DATA 3.48E-07 NO DATA 5.31 E-06 NO DATA 1.78E-04AG 110M 1.60E-07 1.48E-07 8.79E-08 NO DATA 2.91 E-07 NO DATA 6.04E-05SB 125 1.79E-06 2.00E-08 4.26E-07 1.82E-09 0.0 1.38E-06 1.97E-05TE 125M 2.68E-06 9.71 E-07 3.59E-07 8.06E-07 1.09E-05 NO DATA 1.07E-05TE.127M 6.77E-06 2.42E-06 8.25E-07 1.73E-06 2.75E-05 NO DATA 2.27E-05TE 127 1.10E-07 3.95E-08 2.38E-08 8.15E-08 4.48E-07 NO DATA 8.68E-06TE 129M 1.15E-05 4.29E-06 1.82E-06 3.95E-06 4.80E-05 NO DATA 5.79E-05.. .............................................  
.................................  
.................................  
*..............................................................................................
*..............................................................................................
TE 129 3.14E-08 1.18E-08 7.65E-09 2.41 E-08 1.32E-07 NO DATA 2.37E-08TE 131M 1.73E-06 8.46E-07 7.05E-07 1.34E-06 8.57E-06 NO DATA 8.40E-05TE 131 1.97E-08 8.23E-09 6.22E-09 1.62E-08 8.63E-08 NO DATA 2.79E-09.. .............................................................................................................................................................................
TE 129 3.14E-08 1.18E-08 7.65E-09 2.41 E-08 1.32E-07 NO DATA 2.37E-08 TE 131M 1.73E-06 8.46E-07 7.05E-07 1.34E-06 8.57E-06 NO DATA 8.40E-05 TE 131 1.97E-08 8.23E-09 6.22E-09 1.62E-08 8.63E-08 NO DATA 2.79E-09.. .............................................................................................................................................................................
TE 132 2.52E-06 1.63E-06 1.53E-06 1.80E-06 1.57E-05 NO DATA 7.71E-05I 130 7.56E-07 2.23E-06 8.80E-07 1.89E-04 3.48E-06 NO DATA 1.92E-06I 131 4.16E-06 5.95E-06 3.41E-06 1.95E-03 1.02E-05 NO DATA 1.57E-06I. 132 2.03E-07 E-07 5.ZE-07 1.90E-07 1.90E-05 8.65E-07 NO DATA 1.02E-07I 133 1.42E-06 2.47E-06 7.53E-07 3.63E-04 4.31 E-06 NO DATA 2.22E-06I 134 1.06E-07 2.88E-07 1.03E-07 4.99E-06 4.58E-07 NO DATA 2.51 E-10 CY-TM-1 70-300Revision 3Page 111 of 209TABLE 2.1Liquid Dose Conversion Factors (DCF): DFIjPage 3 of 3Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)
TE 132 2.52E-06 1.63E-06 1.53E-06 1.80E-06 1.57E-05 NO DATA 7.71E-05 I 130 7.56E-07 2.23E-06 8.80E-07 1.89E-04 3.48E-06 NO DATA 1.92E-06 I 131 4.16E-06 5.95E-06 3.41E-06 1.95E-03 1.02E-05 NO DATA 1.57E-06 I. 132 2.03E-07 E-07 5.ZE-07 1.90E-07 1.90E-05 8.65E-07 NO DATA 1.02E-07 I 133 1.42E-06 2.47E-06 7.53E-07 3.63E-04 4.31 E-06 NO DATA 2.22E-06 I 134 1.06E-07 2.88E-07 1.03E-07 4.99E-06 4.58E-07 NO DATA 2.51 E-10 CY-TM-1 70-300 Revision 3 Page 111 of 209 TABLE 2.1 Liquid Dose Conversion Factors (DCF): DFIj Page 3 of 3 Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLI I 135 4.43E-07 1.16E-06 4.28E-07 7.65E-05 1.86E-06 NO DATA 1.31 E-06 CS 134 6.22E-05 1.48E-04 1.21E-04 NO DATA 4.79E-05 1.59E-05 2.59E-06 CS 136 6.51 E-06 2.57E-05 1.85E-05 NO DATA 1.43E-05 1.96E-06 2.92E-06 CS.137 7.97E-05 1.09E-04 7.14E-05 NO DATA 3.70E-05 1.23E-05 2.11E-06 CS 138 5.52E-08 1.09E-07 5.40E-08 NO DATA 8.01E-08 7.91E-09 4.65E-13 BA 139 9.70E-08 6.91E-11 2.84E-09 NO DATA 6.46E-11 3.92E-11 1.72E-07 BA 140 2.03E-05 2.55E-08 1.33E-06 NO DATA 8.67E-09 1.46E-08 4.18E-05 BA 141 4.71E-08 3.56E-11 1.59E-09 NO DATA 3.31E-11 2.02E-11 2.22E-17 BA 142 2.13E-08 2.19E-11 1.34E-09 NO DATA 1.85E-11 1.24E-11 3.OOE-26.............  
NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLII 135 4.43E-07 1.16E-06 4.28E-07 7.65E-05 1.86E-06 NO DATA 1.31 E-06CS 134 6.22E-05 1.48E-04 1.21E-04 NO DATA 4.79E-05 1.59E-05 2.59E-06CS 136 6.51 E-06 2.57E-05 1.85E-05 NO DATA 1.43E-05 1.96E-06 2.92E-06CS.137 7.97E-05 1.09E-04 7.14E-05 NO DATA 3.70E-05 1.23E-05 2.11E-06CS 138 5.52E-08 1.09E-07 5.40E-08 NO DATA 8.01E-08 7.91E-09 4.65E-13BA 139 9.70E-08 6.91E-11 2.84E-09 NO DATA 6.46E-11 3.92E-11 1.72E-07BA 140 2.03E-05 2.55E-08 1.33E-06 NO DATA 8.67E-09 1.46E-08 4.18E-05BA 141 4.71E-08 3.56E-11 1.59E-09 NO DATA 3.31E-11 2.02E-11 2.22E-17BA 142 2.13E-08 2.19E-11 1.34E-09 NO DATA 1.85E-11 1.24E-11 3.OOE-26.............  
............  
............  
.....................................................................................................................................................
.....................................................................................................................................................
LA 140 2.50E-09 1.26E-09.
LA 140 2.50E-09 1.26E-09.
3.33E-10 NO DATA NO DATA NO DATA 9.25E-05LA 142 1.28E-10 5.82E-11 1.45E-11 NO DATA NO DATA NO DATA 4.25E-07CE 141 9.36E-09 6.33E-09 7.18E-10 NO DATA 2.94E-09 NO DATA 2.42E-05CE-143 1.65E-09 1.22E-06 1.35E-10 NO DATA 5.37E-10 NO DATA 4.56E-05CE 144 4.88E-07 2.04E-07 2.62E-08 NO DATA 1.21 E-07 NO DATA 1.65E-04PR 143 9.20E-09 3.69E-09 4.56E-10 NO DATA 2.13E-09 NO DATA 4.03E-05PR.144 3.01 E-11 1.25E-11 1.53E-12 NO DATA 7.05E-12 NO DATA 4.33E-18ND 147 6.29E-09 7.27E-09 4.35E-10 NO DATA 4.25E-09 NO DATA 3.49E-05W 187 1.03E-07 8.61 E-08 3.01E-08 NO DATA NO DATA NO DATA 2.82E-05N-.23 9 ... --- ........ 1" .......-E.. .D , ....3"."... E'"0 NO D A -.6E- ., ...NO... D T *0E"-"5Dose factors of internal exposure are for continuous intake over a one-year period andinclude the dose commitment over a 50-year period; from Reg. Guide 1.109 (Rev. 1).Additional dose factors for nuclides not included in this table may be obtained fromNUREG-0172.
3.33E-10 NO DATA NO DATA NO DATA 9.25E-05 LA 142 1.28E-10 5.82E-11 1.45E-11 NO DATA NO DATA NO DATA 4.25E-07 CE 141 9.36E-09 6.33E-09 7.18E-10 NO DATA 2.94E-09 NO DATA 2.42E-05 CE-143 1.65E-09 1.22E-06 1.35E-10 NO DATA 5.37E-10 NO DATA 4.56E-05 CE 144 4.88E-07 2.04E-07 2.62E-08 NO DATA 1.21 E-07 NO DATA 1.65E-04 PR 143 9.20E-09 3.69E-09 4.56E-10 NO DATA 2.13E-09 NO DATA 4.03E-05 PR.144 3.01 E-11 1.25E-11 1.53E-12 NO DATA 7.05E-12 NO DATA 4.33E-18 ND 147 6.29E-09 7.27E-09 4.35E-10 NO DATA 4.25E-09 NO DATA 3.49E-05 W 187 1.03E-07 8.61 E-08 3.01E-08 NO DATA NO DATA NO DATA 2.82E-05 N-.23 9 ... --- ........ 1" .......-E.. .D , ....3"."... E'"0 NO D A -.6E- ., ...NO... D T *0E"-"5 Dose factors of internal exposure are for continuous intake over a one-year period and include the dose commitment over a 50-year period; from Reg. Guide 1.109 (Rev. 1).Additional dose factors for nuclides not included in this table may be obtained from NUREG-0172.
CY-TM-1 70-300Revision 3Page 112 of 209TABLE 2.2Bloaccumulation
CY-TM-1 70-300 Revision 3 Page 112 of 209 TABLE 2.2 Bloaccumulation Factors, BF, Bioaccumulation Factors to be Used in the Absence of Site-Specific Data*(pCi/kg per pCi/liter)
: Factors, BF,Bioaccumulation Factors to be Used in the Absence of Site-Specific Data*(pCi/kg per pCi/liter)
ELEMENT FRESHWATER FISH INVERTEBRATE H 9.OE-01 9.OE-01 C 4.6E+03 9.1E+03 NA 1.OE+02 2.OE+02 CR 2.OE+02 2.OE+03 MN 4.OE+02 9.OE+04 FE 1.OE+02 3.2E+03 CO 5.OE+01 2.OE+02 NI 1.OE+02 1.OE+02 CU 5.OE+01 4.OE+02 ZN 2.OE+03 1.OE+04 BR 4.2E+02 3.3E+02 RB 2.OE+03 1.OE+03 SR 3.OE+01 1.OE+02 Y 2.5E+01 1.OE+03 ZR 3.3E+00 6.7E+00 NB 3.OE+04 1.OE+02 MO 1.OE+01 1.OE+01 TC 1.5E+01 5.OE+00 RU 1.OE+01 3.OE+02 RH 1.OE+01 3.OE+02***AG-110m 2.30E+1 7.70E+2**SB 1.OE+00 1.OE+00 TE 4.OE+02 6.1 E+03 I 1.5E+01 5.OE+00 CS 2.OE+03 1.OE+03 BA 4.OE+00 2.OE+02 LA 2.5E+01 1.OE+03 CE 1.OE+00 1.OE+03 PR 2.5E+01 1.OE+03 ND 2.5E+01 1.OE+03 W 1.2E+03 1.OE+01 NP 1.OE+01 4.OE+02* Bioaccumulation factor values are taken from Reg. Guide 1.109 (Rev. 1), Table A-1j.** Sb bioaccumulation factor value is taken from EPRI NP-3840.Ag bioaccumulation factor value is taken from Reg. Guide 1.109 (Rev. 0), Table A-8.
ELEMENT FRESHWATER FISH INVERTEBRATE H 9.OE-01 9.OE-01C 4.6E+03 9.1E+03NA 1.OE+02 2.OE+02CR 2.OE+02 2.OE+03MN 4.OE+02 9.OE+04FE 1.OE+02 3.2E+03CO 5.OE+01 2.OE+02NI 1.OE+02 1.OE+02CU 5.OE+01 4.OE+02ZN 2.OE+03 1.OE+04BR 4.2E+02 3.3E+02RB 2.OE+03 1.OE+03SR 3.OE+01 1.OE+02Y 2.5E+01 1.OE+03ZR 3.3E+00 6.7E+00NB 3.OE+04 1.OE+02MO 1.OE+01 1.OE+01TC 1.5E+01 5.OE+00RU 1.OE+01 3.OE+02RH 1.OE+01 3.OE+02***AG-110m 2.30E+1 7.70E+2**SB 1.OE+00 1.OE+00TE 4.OE+02 6.1 E+03I 1.5E+01 5.OE+00CS 2.OE+03 1.OE+03BA 4.OE+00 2.OE+02LA 2.5E+01 1.OE+03CE 1.OE+00 1.OE+03PR 2.5E+01 1.OE+03ND 2.5E+01 1.OE+03W 1.2E+03 1.OE+01NP 1.OE+01 4.OE+02* Bioaccumulation factor values are taken from Reg. Guide 1.109 (Rev. 1), Table A-1j.** Sb bioaccumulation factor value is taken from EPRI NP-3840.Ag bioaccumulation factor value is taken from Reg. Guide 1.109 (Rev. 0), Table A-8.
CY-TM-170-300 Revision 3 Page 113 of 209 3.0 TMI LIQUID EFFLUENT WASTE TREATMENT SYSTEM 3.1 TMI-1 Liquid Effluent Waste Treatment System 3.1.1 Description of the Liquid Radioactive Waste Treatment System (see Figure 3.1)Reactor Coolant Train a. Water Sources -(3) Reactor Coolant Bleed Tanks (RCBT)-(1) Reactor Coolant Drain Tank (RCDT)b. Liquid Processing  
CY-TM-170-300 Revision 3Page 113 of 2093.0 TMI LIQUID EFFLUENT WASTE TREATMENT SYSTEM3.1 TMI-1 Liquid Effluent Waste Treatment System3.1.1 Description of the Liquid Radioactive Waste Treatment System (seeFigure 3.1)Reactor Coolant Traina. Water Sources -(3) Reactor Coolant Bleed Tanks (RCBT)-(1) Reactor Coolant Drain Tank (RCDT)b. Liquid Processing  
-Reactor Coolant Waste Evaporator
-Reactor Coolant Waste Evaporator
-Demineralizers prior to release(see Figure 3.2)c. Liquid Effluent for Release-(2) Waste Evaporator Condensate Storage Tanks -(WECST)d. Dilution  
-Demineralizers prior to release (see Figure 3.2)c. Liquid Effluent for Release- (2) Waste Evaporator Condensate Storage Tanks -(WECST)d. Dilution -Mechanical Draft Cooling Tower (0-38k gpm)-River Flow (2E7 gpm average)Miscellaneous Waste Train a. Water sources: -Auxiliary Building Sump-Reactor Building Sump-Miscellaneous Waste Storage Tank-Laundry Waste Storage Tank-Neutralizer Mixing Tank-Neutralizer Feed Tank-Used Precoat Tank-Borated Water Tank Tunnel Sump-Heat Exchanger Vault Sump-Tendon Access Galley Sump-Spent Fuel Pool Room Sump-TMI-2 Miscellaneous Waste Holdup Tank CY-TM-1 70-300 Revision 3 Page 114 of 209 b. Liquid Processing  
-Mechanical Draft Cooling Tower (0-38k gpm)-River Flow (2E7 gpm average)Miscellaneous Waste Traina. Water sources:  
-Miscellaneous Waste Evaporator, MWE-Demineralizers prior to release (see Figure 3.2)c. Liquid Effluent for Release -(2) Waste Evaporator Condensate Storage Tanks- (WECST)d. Dilution -Mechanical Draft Cooling Tower (0-38k gpm)-River Flow (2E7 gpm average)3.2 Operability of the TMI-1 Liquid Effluent Waste Treatment System 3.2.1 The TMI-1 Liquid Waste Treatment System as described in Section 11 of the TMI-1 Final Safety Analysis Report is considered to be operable when one of each of the following pieces of equipment is available to perform its intended function: a) Miscellaneous Waste Evaporator (WDL-Z1 B) or Reactor Coolant Evaporator (WDL-Z1 A)b) Waste Evaporator Condensate Demineralizer (WDL-K3 A or B)c) Waste Evaporator Condensate Storage Tank (WDL-T 11 A or B)d) Evaporator Condensate Pumps (WDL-P 14 A or B)3.2.2 TMI-1 Representative Sampling Prior to Discharge All liquid releases from the TMI-1 Liquid Waste Treatment System are made through the Waste Evaporator Condensate Storage Tanks. To provide thorough mixing and a representative sample, the contents of the tank are recirculated using one of the Waste Evaporator Condensate Transfer Pumps.3.3 TMI-2 Liquid Effluent Waste Treatment System 3.3.1 Description of the TMI-2 Liquid Radioactive Waste Treatment System The TMI-2 Liquid Radioactive Waste Treatment System has been out of service since the TMI-2 Accident in 1979. TMI-2 Liquid Radioactive Waste is processed by the TMI-1 system described in Section 3.1 prior to release. In addition, TMI-2 releases water from various sumps and tanks to the river (see Figures 1.1 and 1.2). These processes are governed by plant procedures that encompass proper sampling, sample analysis, and radiation monitoring techniques.
-Auxiliary Building Sump-Reactor Building Sump-Miscellaneous Waste Storage Tank-Laundry Waste Storage Tank-Neutralizer Mixing Tank-Neutralizer Feed Tank-Used Precoat Tank-Borated Water Tank Tunnel Sump-Heat Exchanger Vault Sump-Tendon Access Galley Sump-Spent Fuel Pool Room Sump-TMI-2 Miscellaneous Waste Holdup Tank CY-TM-1 70-300Revision 3Page 114 of 209b. Liquid Processing  
CY-TM-1 70-300 Revision 3 Page 115 of 209 FIGURE 3.1 TMI-1 Liquid Radwaste CY-TM-170-300 Revision 3 Page 116 of 209 FIGURE 3.2 TMI-1 Liquid Waste Evaporators DIST.
-Miscellaneous Waste Evaporator, MWE-Demineralizers prior to release(see Figure 3.2)c. Liquid Effluent for Release -(2) Waste Evaporator Condensate Storage Tanks- (WECST)d. Dilution  
CY-TM-1 70-300 Revision 3 Page 117 of 209 4.0 GASEOUS EFFLUENT MONITORS 4.1 TMI-1 Noble Gas Monitor Set Points The gaseous effluent monitor set points are established for each gaseous effluent radiation monitor to assure concentrations of radionuclides in gaseous effluents do not exceed the limits set forth in ODCM Part I Control 2.2.2.1.Table 4.1 lists Gaseous Effluent Release Points and their associated parameters; Figure 4.1 provides a Gaseous Effluent Release Pathway Diagram.The set points are established to satisfy the more restrictive set point concentration in the following two equations:
-Mechanical Draft Cooling Tower (0-38k gpm)-River Flow (2E7 gpm average)3.2 Operability of the TMI-1 Liquid Effluent Waste Treatment System3.2.1 The TMI-1 Liquid Waste Treatment System as described in Section 11of the TMI-1 Final Safety Analysis Report is considered to be operablewhen one of each of the following pieces of equipment is available toperform its intended function:
500> >. (c 1)(F)(K 1)(Dv) (eq 4.1.1)and 3000 > I (cq)(LI + 1.1 Mi)(Dv)(F) (eq 4.1.2)Where: ci = set point concentration based on Xe-1 33 equivalent, in iCi/cc F =gaseous effluent flowrate at the monitor, in cc/sec Ki =total body dose factor, in mrem/yr per p.Ci/m 3 from Table 4.3 Dv = highest sector annual average gaseous atmospheric dispersion factor (X/Q) at or beyond the unrestricted area boundary, in sec/m 3 , from Table 4.4 for station vent releases and Table 4.5 for all other releases, (Condenser off gas, ESF FHB, and ground releases).
a) Miscellaneous Waste Evaporator (WDL-Z1 B) or Reactor CoolantEvaporator (WDL-Z1 A)b) Waste Evaporator Condensate Demineralizer (WDL-K3 A or B)c) Waste Evaporator Condensate Storage Tank (WDL-T 11 A or B)d) Evaporator Condensate Pumps (WDL-P 14 A or B)3.2.2 TMI-1 Representative Sampling Prior to Discharge All liquid releases from the TMI-1 Liquid Waste Treatment System aremade through the Waste Evaporator Condensate Storage Tanks. Toprovide thorough mixing and a representative sample, the contents ofthe tank are recirculated using one of the Waste Evaporator Condensate Transfer Pumps.3.3 TMI-2 Liquid Effluent Waste Treatment System3.3.1 Description of the TMI-2 Liquid Radioactive Waste Treatment SystemThe TMI-2 Liquid Radioactive Waste Treatment System has been out ofservice since the TMI-2 Accident in 1979. TMI-2 Liquid Radioactive Waste is processed by the TMI-1 system described in Section 3.1 priorto release.
Maximum values presently used are 1.27E-6 sec/m 3 at sector SE for station vent, and 1.40E-5 sec/M 3 at sector E for all other releases.Li= skin dose factor due to beta emissions from radionuclide i, in mrem/yr per jLCi/m 3 from Table 4.3.MI = air dose factor due to gamma emissions from radionuclide i, in mrad/yr per p.Ci/m 3 from Table 4.3.1.1 = mrem skin dose per mrad air dose.500 = annual whole body dose rate limit for unrestricted areas, in mrem/yr.3000 = annual skin dose rate limit for unrestricted areas, in mrem/yr.
In addition, TMI-2 releases water from various sumps andtanks to the river (see Figures 1.1 and 1.2). These processes aregoverned by plant procedures that encompass proper sampling, sampleanalysis, and radiation monitoring techniques.
CY-TM-1 70-300 Revision 3 Page 118 of 209 The set point concentration is further reduced such that the concentration contributions from multiple release points would not combine to exceed ODCM Control limits.The set point concentration is converted to set point scale units on each radiation monitor using appropriate calibration factors.This section of the ODCM is implemented by the Radiation Monitor System Set Points procedure and the procedure for Releasing Radioactive Gaseous Waste.
CY-TM-1 70-300Revision 3Page 115 of 209FIGURE 3.1TMI-1 Liquid Radwaste CY-TM-170-300 Revision 3Page 116 of 209FIGURE 3.2TMI-1 Liquid Waste Evaporators DIST.
CY-TM-170-300 Revision 3 Page 119 of 209 4.2 TMI-1 Particulate and Radioiodine Monitor Set Points Set points for monitors which detect radionuclides other than noble gases are also established to assure that concentrations of these radionuclides in gaseous effluents do not exceed the limits of ODCM Part I Control 2.2.2.1.Set points are established so as to satisfy the following equations:
CY-TM-1 70-300Revision 3Page 117 of 2094.0 GASEOUS EFFLUENT MONITORS4.1 TMI-1 Noble Gas Monitor Set PointsThe gaseous effluent monitor set points are established for each gaseouseffluent radiation monitor to assure concentrations of radionuclides in gaseouseffluents do not exceed the limits set forth in ODCM Part I Control 2.2.2.1.Table 4.1 lists Gaseous Effluent Release Points and their associated parameters; Figure 4.1 provides a Gaseous Effluent Release Pathway Diagram.The set points are established to satisfy the more restrictive set pointconcentration in the following two equations:
1500 > (ci)(F)(P 1)(Ov) (eq 4.2)Where: c 1 = set point concentration based on 1-131 equivalent for radioiodine monitor and Sr-90 for particulate monitor, in VLCi/cc F = gaseous effluent flow rate at the monitor, in cc/sec Pi = pathway dose parameter, in mrem/yr per p.Ci/m3 for the inhalation pathway from Table 4.6. The dose factors are based on the actual individual organ and most restrictive age group (child) (NUREG-0133).
500> >. (c1)(F)(K1)(Dv) (eq 4.1.1)and3000 > I (cq)(LI + 1.1 Mi)(Dv)(F)  
(eq 4.1.2)Where: ci = set point concentration based on Xe-1 33 equivalent, in iCi/ccF =gaseous effluent flowrate at the monitor, in cc/secKi =total body dose factor, in mrem/yr per p.Ci/m3 from Table 4.3Dv = highest sector annual average gaseous atmospheric dispersion factor(X/Q) at or beyond the unrestricted area boundary, in sec/m3, fromTable 4.4 for station vent releases and Table 4.5 for all other releases, (Condenser off gas, ESF FHB, and ground releases).
Maximum valuespresently used are 1.27E-6 sec/m3 at sector SE for station vent, and1.40E-5 sec/M3 at sector E for all other releases.
Li= skin dose factor due to beta emissions from radionuclide i, in mrem/yrper jLCi/m3 from Table 4.3.MI = air dose factor due to gamma emissions from radionuclide i, in mrad/yrper p.Ci/m3 from Table 4.3.1.1 = mrem skin dose per mrad air dose.500 = annual whole body dose rate limit for unrestricted areas, in mrem/yr.3000 = annual skin dose rate limit for unrestricted areas, in mrem/yr.
CY-TM-1 70-300Revision 3Page 118 of 209The set point concentration is further reduced such that the concentration contributions from multiple release points would not combine to exceed ODCMControl limits.The set point concentration is converted to set point scale units on each radiation monitor using appropriate calibration factors.This section of the ODCM is implemented by the Radiation Monitor System SetPoints procedure and the procedure for Releasing Radioactive Gaseous Waste.
CY-TM-170-300 Revision 3Page 119 of 2094.2 TMI-1 Particulate and Radioiodine Monitor Set PointsSet points for monitors which detect radionuclides other than noble gases arealso established to assure that concentrations of these radionuclides in gaseouseffluents do not exceed the limits of ODCM Part I Control 2.2.2.1.Set points are established so as to satisfy the following equations:
1500 > (ci)(F)(P 1)(Ov) (eq 4.2)Where: c1 = set point concentration based on 1-131 equivalent for radioiodine monitorand Sr-90 for particulate  
: monitor, in VLCi/ccF = gaseous effluent flow rate at the monitor, in cc/secPi = pathway dose parameter, in mrem/yr per p.Ci/m3 for the inhalation pathway from Table 4.6. The dose factors are based on the actualindividual organ and most restrictive age group (child) (NUREG-0133).
NOTE: Appendix A contains Pi calculational methodology.
NOTE: Appendix A contains Pi calculational methodology.
1500 = annual dose rate limit to any organ from particulates and radioiodines and radionuclides (other than noble gases) with half lives greater thaneight days in mrem/yr.Dv = highest sector annual average gaseous dispersion factor (X/Q or D/Q) ator beyond the unrestricted area boundary from Table 4.4 for releasesfrom the station vent and Table 4.5 for all other releases.
1500 = annual dose rate limit to any organ from particulates and radioiodines and radionuclides (other than noble gases) with half lives greater than eight days in mrem/yr.Dv = highest sector annual average gaseous dispersion factor (X/Q or D/Q) at or beyond the unrestricted area boundary from Table 4.4 for releases from the station vent and Table 4.5 for
X/Q is used forthe inhalation pathway.
Maximum values of X/Q presently used are1.27E-6 sec/m3 for station vent, at sector SE, and 1.40E-5 sec
--------------
--------------
1SR-90 0.OOE+00 0.OOE+00Y-91 1.07E+06 1.21 E+06ZR-95 2.45E+08 2.84E+08NB-95 1.37E+08 1.61 E+08RU-103 1.08E+08 1.26E+08RU-106 4.22E+08 5.06E+08AG-1i1M 3.44E+09 4.01"E+09
1 SR-90 0.OOE+00 0.OOE+00 Y-91 1.07E+06 1.21 E+06 ZR-95 2.45E+08 2.84E+08 NB-95 1.37E+08 1.61 E+08 RU-103 1.08E+08 1.26E+08 RU-106
'TE-125M 1.55E+06 2.


====8.2.2 Applicability====
====8.2.2 Applicability====
At all times.8.2.3 Actiona. With a Land Use Census identifying a location(s) that yields acalculated dose or dose commitment greater than the valuescurrently being calculated in ODCM Part I Surveillance 3.2.2.3.1, pursuant to ODCM, Part IV, Section 2.0, identify thenew location(s) in the next Annual Radioactive EffluentRelease Report.b. With a Land Use Census identifying a location(s) that yields acalculated dose or dose commitment (via the same exposurepathway) 20% greater than at a location from which samplesare currently being obtained in accordance with Table 8.1, addthe new location(s) within 30 days to the Radiological Environmental Monitoring Program given in the ODCM. Thesampling location(s),
At all times.8.2.3 Action a. With a Land Use Census identifying a location(s) that yields a calculated dose or dose commitment greater than the values currently being calculated in ODCM Part I Surveillance 3.2.2.3.1, pursuant to ODCM, Part IV, Section 2.0, identify the new location(s) in the next Annual Radioactive Effluent Release Report.b. With a Land Use Census identifying a location(s) that yields a calculated dose or dose commitment (via the same exposure pathway) 20% greater than at a location from which samples are currently being obtained in accordance with Table 8.1, add the new location(s) within 30 days to the Radiological Environmental Monitoring Program given in the ODCM. The sampling location(s), excluding the control station location, having the lowest calculated dose or dose commitment(s), via the same exposure pathway, may be deleted from this monitoring program after October 31 of the year in which this Land Use Census was conducted.
excluding the control station location, having the lowest calculated dose or dose commitment(s),
Pursuant to TMI-1 Tech.Spec. 6.14 and TMI-2 PDMS Tech. Spec. 6.12, submit in the next Annual Radioactive Effluent Release Report documentation for a change in the ODCM including a revised figure(s) and table(s) for the ODCM reflecting the new location(s) with information supporting the change in sampling locations.
viathe same exposure  
Broad leaf vegetation sampling of at least three different kinds of vegetation may be performed at the site boundary in each of two different sectors with the highest predicted D/Qs in lieu of the garden census.Requirements for broad leaf sampling in Table 8.1 shall be followed, including analysis of control samples.
: pathway, may be deleted from thismonitoring program after October 31 of the year in which thisLand Use Census was conducted.
CY-TM-1 70-300 Revision 3 Page 172 of 209 8.2.4 Bases This Control is provided to ensure that changes in the use of unrestricted areas are identified and modifications to the monitoring program are made if required by the results of this census. The best information from the door-to-door survey, aerial surveys, or consulting with local agricultural authorities shall be used. This census satisfies the requirements of Section IV.B.3 of Appendix I to 10 CFR 50. Restricting the census to gardens of greater than 500 square feet (50 M 2) provides assurance that significant exposure pathways via leafy vegetables will be identified and monitored since a garden of this size is the minimum required to produce the quantity (26 kg/yr) of leafy vegetables assumed in Regulatory Guide 1.109 for consumption by a child. To determine this minimum garden size, the following assumptions were used: 1) that 20% of the garden was used for growing broad leaf vegetation (i.e., similar to lettuce and cabbage), and 2) a vegetation yield of 2 kg/square meter.8.2.5 Surveillance Requirements The Land Use Census shall be conducted during the growing season at least once per 12 months, using that information that.will provide the best results, such as by a door-to-door survey, aerial survey, or by consulting local agricultural authorities.
Pursuant to TMI-1 Tech.Spec. 6.14 and TMI-2 PDMS Tech. Spec. 6.12, submit in thenext Annual Radioactive Effluent Release Reportdocumentation for a change in the ODCM including a revisedfigure(s) and table(s) for the ODCM reflecting the newlocation(s) with information supporting the change in samplinglocations.
The results of the Land Use Census shall be included in the Annual Radiological Environmental Operating Report pursuant to ODCM, Part IV, Section 1.0.
Broad leaf vegetation sampling of at least three different kinds of vegetation may be performed at the siteboundary in each of two different sectors with the highest predicted D/Qs in lieu of the garden census.Requirements for broad leaf sampling in Table 8.1 shall be followed, including analysis of control samples.
CY-TM-1 70-300 Revision 3 Page 173 of 209 8.3 Interlaboratory Comparison Program 8.3.1 Controls In accordance with the TMI-1 Tech. Specs. and TMI-2 PDMS Tech.Specs., analyses shall be performed on radioactive materials supplied as part of an Interlaboratory Comparison Program which has been approved by the Commission (NRC). Only those samples and analyses which are required by Table 8.1 shall be performed.
CY-TM-1 70-300Revision 3Page 172 of 2098.2.4 BasesThis Control is provided to ensure that changes in the use of unrestricted areas are identified and modifications to the monitoring program aremade if required by the results of this census. The best information fromthe door-to-door survey, aerial surveys, or consulting with localagricultural authorities shall be used. This census satisfies therequirements of Section IV.B.3 of Appendix I to 10 CFR 50. Restricting the census to gardens of greater than 500 square feet (50 M2) providesassurance that significant exposure pathways via leafy vegetables willbe identified and monitored since a garden of this size is the minimumrequired to produce the quantity (26 kg/yr) of leafy vegetables assumedin Regulatory Guide 1.109 for consumption by a child. To determine thisminimum garden size, the following assumptions were used: 1) that20% of the garden was used for growing broad leaf vegetation (i.e., similar to lettuce and cabbage),
and 2) a vegetation yield of2 kg/square meter.8.2.5 Surveillance Requirements The Land Use Census shall be conducted during the growing season atleast once per 12 months, using that information that.will provide thebest results, such as by a door-to-door survey, aerial survey, or byconsulting local agricultural authorities.
The results of the Land UseCensus shall be included in the Annual Radiological Environmental Operating Report pursuant to ODCM, Part IV, Section 1.0.
CY-TM-1 70-300Revision 3Page 173 of 2098.3 Interlaboratory Comparison Program8.3.1 ControlsIn accordance with the TMI-1 Tech. Specs. and TMI-2 PDMS Tech.Specs., analyses shall be performed on radioactive materials suppliedas part of an Interlaboratory Comparison Program which has beenapproved by the Commission (NRC). Only those samples and analyseswhich are required by Table 8.1 shall be performed.


====8.3.2 Applicability====
====8.3.2 Applicability====
At all times.8.3.3 ActionWith analysis not being performed as required above, report thecorrective action taken to prevent a recurrence to the Commission in theAnnual Radiological Environmental Operating Report.8.3.4 BasesThe requirement for participation in an approved Interlaboratory Comparison Program is provided to ensure that independent checks onprecision and accuracy of the measurements of radioactive material inenvironmental sample matrices are performed as part of a qualityassurance program for environmental monitoring in order to demonstrate that the results are reasonably valid for the purpose of Section IV, B.2 ofAppendix I to 10 CFR 50.8.3.5 Surveillance Requirements A summary of the Interlaboratory Comparison Program results shall beincluded in the Annual Radiological Environmental Operating Report.
At all times.8.3.3 Action With analysis not being performed as required above, report the corrective action taken to prevent a recurrence to the Commission in the Annual Radiological Environmental Operating Report.8.3.4 Bases The requirement for participation in an approved Interlaboratory Comparison Program is provided to ensure that independent checks on precision and accuracy of the measurements of radioactive material in environmental sample matrices are performed as part of a quality assurance program for environmental monitoring in order to demonstrate that the results are reasonably valid for the purpose of Section IV, B.2 of Appendix I to 10 CFR 50.8.3.5 Surveillance Requirements A summary of the Interlaboratory Comparison Program results shall be included in the Annual Radiological Environmental Operating Report.
CY-TM-1 70-300Revision 3Page 174 of 209TABLE 8.1Sample Collection and Analysis Requirements Number of SamplesExposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb
CY-TM-1 70-300 Revision 3 Page 174 of 209 TABLE 8.1 Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb 1. Airborne Radioiodine and Samples from 5 locations Continuous sampler operation Radioiodine Canister: Particulates from Table 8.4. with sample collection weekly, Analyze weekly for 1-131.or more frequently if required Particulate Filter: Three of these samples by dust loading. Analyze for gross beta should be close to the Site radioactivity following filter d Boundary, in different change .Perform gamma sectors, of the highest isotopic analysise on calculated annual average composite (by location)ground level D/Q. sample quarterly.
: 1. AirborneRadioiodine and Samples from 5 locations Continuous sampler operation Radioiodine Canister:
One of the samples should be from the vicinity of a community having the highest calculated annual average ground level D/Q.And one sample should be from a control location 15 to 30 km distant in a less prevalent wind direction.
Particulates from Table 8.4. with sample collection weekly, Analyze weekly for 1-131.or more frequently if required Particulate Filter:Three of these samples by dust loading.
CY-TM-170-300 Revision 3 Page 175 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency____ S m Cy oAnlysisb and/or Sample Sample Locationsa CollectionFrequency_
Analyze for gross betashould be close to the Site radioactivity following filterdBoundary, in different change .Perform gammasectors, of the highest isotopic analysise oncalculated annual average composite (by location) ground level D/Q. sample quarterly.
of Analysis _2. Direct Radiationc Samples from 40 locations Sample Quarterly Analyze for gamma dose from Table 8.5 (using either quarterly.
One of the samples shouldbe from the vicinity of acommunity having thehighest calculated annualaverage ground level D/Q.And one sample should befrom a control location 15to 30 km distant in a lessprevalent wind direction.
2 dosimeters or at least 1 instrument for continuously measuring and recording dose rate at each location).
CY-TM-170-300 Revision 3Page 175 of 209TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of SamplesExposure Pathway and Sampling and Type and Frequency
Placed as follows: An inner ring of stations, one in each meteorological sector in the general area of the site boundary;An outer ring of stations, one in each meteorological sector in the 6 to 8 km from the site; and the balance of the stations to be placed in special interest areas such as population centers, nearby residences, schools, and in at least one or two areas to serve as control stations.
____ S m Cy oAnlysisb and/or Sample Sample Locationsa CollectionFrequency_
CY-TM-1 70-300 Revision 3 Page 176 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb 3. Waterborne
of Analysis
: a. Surface' Samples from 2 locations Compositeg sample over Perform gamma isotopic from Table 8.6. 1 monthly period. analysis' monthly.Composite for tritium* 1 sample from analysis quarterly.
_2. Direct Radiationc Samples from 40 locations Sample Quarterly Analyze for gamma dosefrom Table 8.5 (using either quarterly.
downstream (indicator) location* 1 sample from upstream (control) location (or location not influenced by the station discharge)
2 dosimeters or at least 1instrument for continuously measuring and recording dose rate at each location).
: b. Drinking Samples from 2 locations Composite 0 sample over Perform gross beta and from Table 8.6. 1 monthly period, gamma isotopic analysise monthly. Perform Sr-90* 1 sample at the location analysis if gross beta of of the nearest water monthly composite  
Placed as follows:An inner ring of stations, one in each meteorological sector in the general areaof the site boundary; An outer ring of stations, one in each meteorological sector in the 6 to 8 km fromthe site; and the balance ofthe stations to be placed inspecial interest areas suchas population centers,nearby residences,
>10 supply that could be times control. Composite for affected by the station tritium analysis quarterly.
: schools, and in at least oneor two areas to serve ascontrol stations.
CY-TM-1 70-300Revision 3Page 176 of 209TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of SamplesExposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb
: 3. Waterborne
: a. Surface' Samples from 2 locations Compositeg sample over Perform gamma isotopicfrom Table 8.6. 1 monthly period. analysis' monthly.Composite for tritium* 1 sample from analysis quarterly.
downstream (indicator) location* 1 sample from upstream(control) location (orlocation not influenced bythe station discharge)
: b. Drinking Samples from 2 locations Composite 0 sample over Perform gross beta andfrom Table 8.6. 1 monthly period, gamma isotopic analysise monthly.
Perform Sr-90* 1 sample at the location analysis if gross beta ofof the nearest water monthly composite  
>10supply that could be times control.
Composite foraffected by the station tritium analysis quarterly.
discharge.
discharge.
* 1 sample from a controllocation.
* 1 sample from a control location.c. Sediment from Samples from 2 locations Sample twice per year Perform gamma isotopic Shoreline (1 Control and 1 Indicator) (Spring and Fall) analysise on each sample.from Table 8.7. 1 1 CY-TM-1 70-300 Revision 3 Page 177 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb 4. Ingestion a. Milk b. Fish Samples from 4 locations from Table 8.8.Samples should be from milking animals in three locations within 5 km distance having the highest dose potential.
: c. Sediment from Samples from 2 locations Sample twice per year Perform gamma isotopicShoreline (1 Control and 1 Indicator)  
If there are none, then one sample from milking animals in each of three areas between 5 to 8 km distant where doses are calculated to be greater than 1 mrem per year.One sample from milking animals at a control location 15 to 30 km distant in a less prevalent wind direction.
(Spring and Fall) analysise on each sample.from Table 8.7. 1 1 CY-TM-1 70-300Revision 3Page 177 of 209TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of SamplesExposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb
Samples from 2 locations from Table 8.9.* 1 sample of recreationally important bottom feeders and 1 sample of recreationally important predators in the vicinity of the station discharge.
: 4. Ingestion
* 1 sample of recreationally important bottom feeders and 1 sample of recreationally important predators from an area not influenced by the station discharge.
: a. Milkb. FishSamples from 4 locations fromTable 8.8.Samples should be frommilking animals in threelocations within 5 km distancehaving the highest dosepotential.
Sample semimonthly when animals are on pasture;monthly at other times.Sample twice per year (Spring and Fall).Perform gamma isotopic analysise and 1-131 analysis on each sample.Composite for Sr-90 analysis quarterly.
If there are none,then one sample from milkinganimals in each of three areasbetween 5 to 8 km distantwhere doses are calculated tobe greater than 1 mrem peryear.One sample from milkinganimals at a control location 15to 30 km distant in a lessprevalent wind direction.
Perform gamma isotopic'and Sr-90 analysis on edible portions.
Samples from 2 locations fromTable 8.9.* 1 sample of recreationally important bottom feeders and1 sample of recreationally important predators in thevicinity of the stationdischarge.
CY-TM-1 70-300 Revision 3 Page 178 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb 4. Ingestion (contd)c. Food Products Samples from 2 locations from Table 8.10 (when available)
* 1 sample of recreationally important bottom feeders and1 sample of recreationally important predators from anarea not influenced by thestation discharge.
* 1 sample of each principle class of food products at a location in the immediate vicinity of the station.(indicator)
Sample semimonthly whenanimals are on pasture;monthly at other times.Sample twice per year(Spring and Fall).Perform gamma isotopicanalysise and 1-131analysis on each sample.Composite for Sr-90analysis quarterly.
* 1 sample of same species or group from a location not influenced by the station discharge.
Perform gamma isotopic' and Sr-90 analysis onedible portions.
Samples of three different kinds of broad leaf vegetation grown nearest each of two different offsite locations of highest predicted annual average ground level D/Q if milking sampling is not performed.
CY-TM-1 70-300Revision 3Page 178 of 209TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of SamplesExposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb
One sample of each of the similar broad leaf vegetation grown 15 to 30 km distant in a less prevalent wind direction if milk sampling is not performed.
: 4. Ingestion (contd)c. FoodProductsSamples from 2 locations from Table 8.10 (whenavailable)
Sample at time of harvest.Monthly during growing season Perform gamma isotopice, and 1-131, analysis on edible portions.
* 1 sample of each principle class of food products at alocation in the immediate vicinity of the station.(indicator)
Sr-90 analysis on green leafy vegetables or vegetation only.Perform gamma isotopice 1-131 analysis.
* 1 sample of same speciesor group from a locationnot influenced by thestation discharge.
CY-TM-170-300 Revision 3 Page 179 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Table Notation a. Sampling locations are provided in Tables 8.4 through 8.10. They are depicted in Maps 8.1 through 8.3. Deviations are permitted from the required sampling schedule if specimens are unobtainable due to hazardous conditions, seasonal unavailability, malfunction of automatic sampling equipment and other legitimate reasons. All deviations from the sampling schedule shall be explained in the Annual Radiological Environmental Operating Report.b. Frequency notation:
Samples of three different kinds of broad leaf vegetation grown nearest each of twodifferent offsite locations ofhighest predicted annualaverage ground level D/Q ifmilking sampling is notperformed.
weekly (7 days), semimonthly (15 days), monthly (31 days), and quarterly (92 days). All surveillance requirements shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% of the surveillance interval.
One sample of each of thesimilar broad leaf vegetation grown 15 to 30 km distant ina less prevalent winddirection if milk sampling isnot performed.
A total maximum combined interval time for any 4 consecutive tests shall not exceed 3.25 times the specified collection or analysis interval.c. One or more instruments, such as a pressurized ion chamber for measuring and recording dose rate continuously, may be used in place of, or in addition to, integrating dosimeters.
Sample at time of harvest.Monthly during growingseasonPerform gammaisotopice, and 1-131,analysis on edibleportions.
For the purpose of this table, a dosimeter is considered to be one phosphor; two or more phosphors in a packet are considered as two or more dosimeters.
Sr-90 analysison green leafyvegetables or vegetation only.Perform gammaisotopice 1-131 analysis.
Film badges shall not be used as dosimeters for measuring direct radiation.
CY-TM-170-300 Revision 3Page 179 of 209TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Table Notationa. Sampling locations are provided in Tables 8.4 through 8.10. They are depicted inMaps 8.1 through 8.3. Deviations are permitted from the required sampling schedule ifspecimens are unobtainable due to hazardous conditions, seasonal unavailability, malfunction of automatic sampling equipment and other legitimate reasons.
: d. Airborne particulate sample filters shall be analyzed for gross beta radioactivity 24 hours or more after sampling to allow for radon and thoron daughter decay. If gross beta activity in an air particulate sample(s) is greater than ten times the calendar year mean of control samples, Sr-90 and gamma isotopic analysis shall be performed on the individual sample(s).
Alldeviations from the sampling schedule shall be explained in the Annual Radiological Environmental Operating Report.b. Frequency notation:
: e. Gamma isotopic analysis means the identification and quantification of gamma-emitting radionuclides that may be attributable to the effluents from the facility.f. The "upstream sample" shall be taken at a distance beyond significant influence of the discharge.
weekly (7 days), semimonthly (15 days), monthly (31 days), andquarterly (92 days). All surveillance requirements shall be performed within thespecified time interval with a maximum allowable extension not to exceed 25% of thesurveillance interval.
The "downstream sample" shall be taken in an area beyond but near the mixing zone.g. Composite sample aliquots shall be collected at time intervals that are short (e.g., hourly) relative to the compositing period (e.g., monthly) in order to assure obtaining a representative sample.
A total maximum combined interval time for any 4 consecutive tests shall not exceed 3.25 times the specified collection or analysis interval.
CY-TM-1 70-300 Revision 3 Page 180 of 209 TABLE 8.2 Reporting Levels for Radioactivity Concentrations in Environmental Samples Airborne Particulate Water or gas Fish Milk Food Products Analysis (pCi/L) _(pCi/m 3) (pCi/kg,wet) (pCi/L) (pCi/kg, wet)H-3 20,000(a)Mn-54 1000 30,000 FE-59 400 10,000 Co-58 1000 30,000 Co-60 300 10,000 Zn-65 300 20,000 Sr-90 8 0.1 100 8 100 Zr-Nb-95 400 1-131 2 0.9 3 100 Cs-134 30 10 1000 60 1000 Cs-1 37 50 20 2000 70 2000 Ba-La-140 200 300 (a) For drinking Water samples. This is 40 CFR Part 141 value.
: c. One or more instruments, such as a pressurized ion chamber for measuring andrecording dose rate continuously, may be used in place of, or in addition to, integrating dosimeters.
CY-TM-1 70-300 Revision 3 Page 181 of 209 TABLE 8.3 Detection Capabilities for Environmental Sample Analysisa Lower Limit of Detection (LLD)b'c Airborne Particulate Fish Food Sediment Water or Gas (pCi/kg, Milk Products (pCi/kg, Analysis (pCi/L) (pCi/m 3) wet) (pCi/L) (pCi/kg,wet) dry)Gross Beta 4 0.01 H-3 2000 Mn-54 15 130 FE-59 30 260 Co-58, 60 15 130 Zn-65 30 260 Zr-95 30 Sr-90 2 0.01 10 2 10 Nb-95 15 1-131 1d 0.07 1 60 Cs-134 15 0.05 130 15 60 150 Cs-137 18 0.06 150 18 80 180 Ba-140 60 60 La-140 15 15 CY-TM-1 70-300 Revision 3 Page 182 of 209 TABLE 8.3 (Cont'd)Detection Capabilities for Environmental Sample Analysisa Table Notation a. This list does not mean that only these nuclides are to be considered.
For the purpose of this table, a dosimeter is considered to be onephosphor; two or more phosphors in a packet are considered as two or moredosimeters.
Other peaks that are identifiable, which may be related to plant operations, together with those of the above nuclides, shall also be analyzed and reported in the Annual Radiological Environmental Operating Report.b. Required detection capabilities for dosimeters used for environmental measurements are given in Regulatory Guide 4.13 (Rev. 1).c. The LLD is defined, for purposes of these controls, as the smallest concentration of radioactive material in a sample that will yield a net count, above system background, that will be detected with 95% probability with only 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):
Film badges shall not be used as dosimeters for measuring directradiation.
LLD = 4.66 Sb E & V
: d. Airborne particulate sample filters shall be analyzed for gross beta radioactivity 24 hoursor more after sampling to allow for radon and thoron daughter decay. If gross betaactivity in an air particulate sample(s) is greater than ten times the calendar year meanof control samples, Sr-90 and gamma isotopic analysis shall be performed on theindividual sample(s).
: e. Gamma isotopic analysis means the identification and quantification of gamma-emitting radionuclides that may be attributable to the effluents from the facility.
: f. The "upstream sample" shall be taken at a distance beyond significant influence of thedischarge.
The "downstream sample" shall be taken in an area beyond but near themixing zone.g. Composite sample aliquots shall be collected at time intervals that are short(e.g., hourly) relative to the compositing period (e.g., monthly) in order to assureobtaining a representative sample.
CY-TM-1 70-300Revision 3Page 180 of 209TABLE 8.2Reporting Levels for Radioactivity Concentrations in Environmental SamplesAirborneParticulate Water or gas Fish Milk Food ProductsAnalysis (pCi/L) _(pCi/m3) (pCi/kg,wet)  
(pCi/L) (pCi/kg, wet)H-3 20,000(a)
Mn-54 1000 30,000FE-59 400 10,000Co-58 1000 30,000Co-60 300 10,000Zn-65 300 20,000Sr-90 8 0.1 100 8 100Zr-Nb-95 4001-131 2 0.9 3 100Cs-134 30 10 1000 60 1000Cs-1 37 50 20 2000 70 2000Ba-La-140 200 300(a) For drinking Water samples.
This is 40 CFR Part 141 value.
CY-TM-1 70-300Revision 3Page 181 of 209TABLE 8.3Detection Capabilities for Environmental Sample Analysisa Lower Limit of Detection (LLD)b'cAirborneParticulate Fish Food SedimentWater or Gas (pCi/kg, Milk Products (pCi/kg,Analysis (pCi/L) (pCi/m3) wet) (pCi/L) (pCi/kg,wet) dry)Gross Beta 4 0.01H-3 2000Mn-54 15 130FE-59 30 260Co-58, 60 15 130Zn-65 30 260Zr-95 30Sr-90 2 0.01 10 2 10Nb-95 151-131 1d 0.07 1 60Cs-134 15 0.05 130 15 60 150Cs-137 18 0.06 150 18 80 180Ba-140 60 60La-140 15 15 CY-TM-1 70-300Revision 3Page 182 of 209TABLE 8.3 (Cont'd)Detection Capabilities for Environmental Sample Analysisa Table Notationa. This list does not mean that only these nuclides are to be considered.
Other peaks thatare identifiable, which may be related to plant operations, together with those of theabove nuclides, shall also be analyzed and reported in the Annual Radiological Environmental Operating Report.b. Required detection capabilities for dosimeters used for environmental measurements are given in Regulatory Guide 4.13 (Rev. 1).c. The LLD is defined, for purposes of these controls, as the smallest concentration ofradioactive material in a sample that will yield a net count, above system background, that will be detected with 95% probability with only 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):
LLD = 4.66 SbE & V
* 2.22
* 2.22
* Y
* Y
* exp (-X At)Where:LLD is the "a priori" lower limit of detection as defined above, as picocuries per unitmass or volume.Sb is the standard deviation of the background counting rate or of the counting rate of ablank sample as appropriate, as counts per minute,E is the counting efficiency, as counts per disintegration, V is the sample size in units of mass or volume,2.22 is the number of disintegrations per minute per picocurie, Y is the fractional radiochemical yield (when applicable),
* exp (-X At)Where: LLD is the "a priori" lower limit of detection as defined above, as picocuries per unit mass or volume.Sb is the standard deviation of the background counting rate or of the counting rate of a blank sample as appropriate, as counts per minute, E is the counting efficiency, as counts per disintegration, V is the sample size in units of mass or volume, 2.22 is the number of disintegrations per minute per picocurie, Y is the fractional radiochemical yield (when applicable), X is the radioactive decay constant for the particular radionuclide and At for environmental samples is the elapsed time between sample collection, or end of the sample collection period, and time of counting.Typical values of E, V, Y and At should be used in the calculation.
X is the radioactive decay constant for the particular radionuclide andAt for environmental samples is the elapsed time between sample collection, or end ofthe sample collection period, and time of counting.
CY-TM-1 70-300 Revision 3 Page 183 of 209 TABLE 8.3 (Cont'd)Detection Capabilities for Environmental Sample Analysisa Table Notation It should be recognized that the LLD is defined as an "a priori" (before the fact) limit representing the capability of a measurement system and not as an "a posteriori" (after the fact) limit for a particular measurement.
Typical values of E, V, Y and At should be used in the calculation.
Analyses shall be performed in such a manner that the stated LLDs will be achieved under routine conditions.
CY-TM-1 70-300Revision 3Page 183 of 209TABLE 8.3 (Cont'd)Detection Capabilities for Environmental Sample Analysisa Table NotationIt should be recognized that the LLD is defined as an "a priori" (before the fact) limitrepresenting the capability of a measurement system and not as an "a posteriori" (afterthe fact) limit for a particular measurement.
Occasionally background fluctuations, unavoidable small samples sizes, the presence of interfering nuclides, or other uncontrollable circumstances may render these LLDs unachievable.
Analyses shall be performed in such amanner that the stated LLDs will be achieved under routine conditions.
In such cases, the contributing factors shall be identified and described in the Annual Radiological Environmental Operating Report.d. LLD for drinking water.
Occasionally background fluctuations, unavoidable small samples sizes, the presence of interfering
CY-TM-170-300 Revision 3 Page 184 of 209 TABLE 8.4 TMINS REMP Station Locations-Air Particulate and Air Iodine Station Code Distance (miles)E1-2 F1-3 G2-1 M2-1 A3-1 H3-1 Q15-1 0.4 0.6 1.4 1.3 2.7 2.2 13.4 Azimuth (0)97 112 126 256 357 160 309 8.1 8.1 8.2 8.2 8.2 8.2 8.3 Map No.TABLE 8.5 TMINS REMP Station Locations-Direct Radiation Station Code Distance (miles)A1-4 B1-1 B1-2 C1-2 D1-1 E1-2 E1-4 F1-2 G1-3 H1-1 J1-1 J1-3 K1 -4 L1-1 M1-1 N1-3 P1-1 P1-2 0.3 0.6 0.4 0.3 0.2 0.4 0.2 0.2 0.2 0.5 0.8 0.3 0.2 0.1 0.1 0.1 0.4 0.1 Azimuth (0)6 25 23 50 76 97 97 112 130 167 176 189 209 236 250 274 303 292 Map No.8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 CY-TM-1 70-300 Revision 3 Page 185 of 209 TABLE 8.5 (Cont'd)TMINS REMP Station Locations-Direct Radiation Station Code Distance (miles)Q1-2 C2-1 K2-1 M2-1 A3-1 H3-1 R3-1 A5-1 B5-1 C5-1 E5-1 F5-1 G5-1 H5-1 J5-1 K5-1 L5-1 M5-1 N5-1 P5-1 Q5-1 R5-1 D6-1 E7-1 Q9-1 B10-1 G10-1 G15-1 J15-1 Q1 5-1 0.2 0.2 1.5 1.2 1.3 2.7 2.2 2.6 4.4 4.9 4.7 4.7 4.7 4.8 4.1 4.9 4.9 4.1 4.3 5.0 5.0 5.0 4.9 5.2 6.7 8.5 9.2 9.7 14.4 12.6 13.4 Azimuth (0)321 335 44 200 256 357 160 341 3 19 43 82 109 131 158 181 202 228 249 268 284 317 339 66 88 310 21 128 126 183 309 Map No.8.1 8.1 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.3 8.3 8.3 8.3 8.3 8.3 8.3 8.3 CY-TM-1 70-300 Revision 3 Page 186 of 209 TABLE 8.6 TMINS REMP Station Locations-Surface Water Station Code Distance (miles) Azimuth (0) Map No.J1-2 (SW) 0.5 188 8.1 A3-2 (SW) 2.7 356 8.2 Q9-1 (DW) 8.5 310 8.3 Q9-1 (SW) 8.5 310 8.3 G15-2 (DW) 13.3 129 8.3 G15-3 (DW) 15.7 124 8.3 (SW) = Surface Water (DW) = Drinking Water TABLE 8.7 TMINS REMP Station Locations-Aquatic Sediment Station Code Distance (miles) Azimuth (0) Map No.A1-3 0.5 359 8.1 K1-3 0.2 212 8.1 J2-1 1.4 179 8.2 CY-TM-1 70-300 Revision 3 Page 187 of 209 Station Code E2-2 F4-1 G2-1 P4-1 K15-3 TABLE 8.8 TMINS REMP Station Locations-Milk Distance (miles) Azimuth (0)1.1 96 3.2 104 1.4 126 3.7 295 14.4 205 Map No.8.2 8.2 8.2 8.2 8.3 TABLE 8.9 TMINS REMP Station Locations-Fish Station Code Station Location IND Downstream of Station Discharge BKG Upstream of Station Discharge Station Code E1-2 H11-2 B10-2 TABLE 8.10 TMINS REMP Station Locations-Food Products Distance (miles) Azimuth (0)0.4 97 1.0 151 10.0 31 Map No.8.1 8.1 8.3 CY-TM-170-300 Revision 3 Page 188 of 209 MAP 8.1 THREE MILE ISLAND NUCLEAR STATION LOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM STATIONS WITHIN I MILE OF THE SITE U U.Z U.4 U _ _ _ _ _MAP 8.1 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Within I Mile of the Site CY-TM-170-300 Revision 3 Page 189 of 209 MAP 8.2 THREE MILE ISLAND NUCLEAR STATION LOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM STATIONS WITHIN 5 MILES OF THE SITE MAP 8.2 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Within 5 Miles of the Site CY-TM-170-300 Revision 3 Page 190 of 209 MAP 8.3 THREE MILE ISLAND NUCLEAR STATION LOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM STATIONS GREATER THAN 5 MILES FROM THE SITE MAP 8.3 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Greater Than 5 Miles from the Site CY-TM-1 70-300 Revision 3 Page 191 of 209 9.0 PART Ill REFERENCES
: nuclides, or other uncontrollable circumstances may render these LLDs unachievable.
: 1. EPRI NP-3840, RP 1560-3 Final Report, "Environmental Radiation Doses From Difficult-To-Measure Nuclides," January 1985 2. "Evaluation of the Three Mile Island Nuclear Station Unit 1 to Demonstrate Conformance to the Design Objectives of 10 CFR 50, Appendix I," Nuclear Safety Associates, May 1976 3. TMI-1 Final Safety Analysis Report (FSAR)4. TMI-2 Final Safety Analysis Report (FSAR)5. Meteorological Information and Dose Assessment System (MIDAS)6. NUREG-0017, "Calculation of Releases of Radioactive Materials in Gaseous and Liquid Effluents from PWR," Revision 1, 1985 7. NUREG-0133, "Preparation of Radiological Effluent Technical Specifications for Nuclear Power Plants," October 1978 8. NUREG-01 72, "AgE-Specific Radiation Dose Commitment Factors For A OnE-Year Chronic Intake," November 1977 9. Regulatory Guide 1.21, "Measuring, Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive Materials in Liquid and Gaseous Effluents from Light-Water Cooled Nuclear Power Plants," Revision 1, June 1974 10. Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR 50, Appendix I," Revision 1, October 1977 11. Simplified Environmental Effluent Dosimetry System (SEEDS)12. TMI Recirculation Factor Memos, April 12, 1988 and March 17, 1988 13. TMI-1 Operations Procedure, 1101-2.1, "Radiation Monitor Set Points" 14. Title 10, Code of Federal Regulations, "Energy" 15. TMI-1 Technical Specifications, attached to Facility Operating License No. DPR-50 16. Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors," Revision 1, July 1977 17. TMI-2 PDMS Technical Specifications, attached to Facility License No. DPR-73 CY-TM-1 70-300 Revision 3 Page 192 of 209 18. Radiological Assessment Branch Technical Position on Environmental Monitoring, Revision 1, November 1979 19. Title 40, Code of Federal Regulations, "Protection of Environment" 20. Regulatory Guide 4.13, "Performance, Testing, and Procedural Specifications for Thermoluminescence Dosimetry:
In such cases, the contributing factors shall be identified and described in the AnnualRadiological Environmental Operating Report.d. LLD for drinking water.
Environmental Applications," Revision 1, July 1977 21. Post-Defueling Monitored Storage Safety Analysis Report (PDMS SAR)
CY-TM-170-300 Revision 3Page 184 of 209TABLE 8.4TMINS REMP Station Locations-Air Particulate and Air IodineStation CodeDistance (miles)E1-2F1-3G2-1M2-1A3-1H3-1Q15-10.40.61.41.32.72.213.4Azimuth (0)971121262563571603098.18.18.28.28.28.28.3Map No.TABLE 8.5TMINS REMP Station Locations-Direct Radiation Station CodeDistance (miles)A1-4B1-1B1-2C1-2D1-1E1-2E1-4F1-2G1-3H1-1J1-1J1-3K1 -4L1-1M1-1N1-3P1-1P1-20.30.60.40.30.20.40.20.20.20.50.80.30.20.10.10.10.40.1Azimuth (0)6252350769797112130167176189209236250274303292Map No.8.18.18.18.18.18.18.18.18.18.18.18.18.18.18.18.18.18.1 CY-TM-1 70-300Revision 3Page 185 of 209TABLE 8.5 (Cont'd)TMINS REMP Station Locations-Direct Radiation Station CodeDistance (miles)Q1-2C2-1K2-1M2-1A3-1H3-1R3-1A5-1B5-1C5-1E5-1F5-1G5-1H5-1J5-1K5-1L5-1M5-1N5-1P5-1Q5-1R5-1D6-1E7-1Q9-1B10-1G10-1G15-1J15-1Q1 5-10.20.21.51.21.32.72.22.64.44.94.74.74.74.84.14.94.94.14.35.05.05.04.95.26.78.59.29.714.412.613.4Azimuth (0)321335442002563571603413194382109131158181202228249268284317339668831021128126183309Map No.8.18.18.28.28.28.28.28.28.28.28.28.28.28.28.28.28.28.28.28.28.28.28.28.38.38.38.38.38.38.38.3 CY-TM-1 70-300Revision 3Page 186 of 209TABLE 8.6TMINS REMP Station Locations-Surface WaterStation Code Distance (miles) Azimuth (0) Map No.J1-2 (SW) 0.5 188 8.1A3-2 (SW) 2.7 356 8.2Q9-1 (DW) 8.5 310 8.3Q9-1 (SW) 8.5 310 8.3G15-2 (DW) 13.3 129 8.3G15-3 (DW) 15.7 124 8.3(SW) = Surface Water(DW) = Drinking WaterTABLE 8.7TMINS REMP Station Locations-Aquatic SedimentStation Code Distance (miles) Azimuth (0) Map No.A1-3 0.5 359 8.1K1-3 0.2 212 8.1J2-1 1.4 179 8.2 CY-TM-1 70-300Revision 3Page 187 of 209Station CodeE2-2F4-1G2-1P4-1K15-3TABLE 8.8TMINS REMP Station Locations-Milk Distance (miles) Azimuth (0)1.1 963.2 1041.4 1263.7 29514.4 205Map No.8.28.28.28.28.3TABLE 8.9TMINS REMP Station Locations-Fish Station Code Station LocationIND Downstream of Station Discharge BKG Upstream of Station Discharge Station CodeE1-2H11-2B10-2TABLE 8.10TMINS REMP Station Locations-Food ProductsDistance (miles) Azimuth (0)0.4 971.0 15110.0 31Map No.8.18.18.3 CY-TM-170-300 Revision 3Page 188 of 209MAP 8.1THREE MILE ISLAND NUCLEAR STATIONLOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAMSTATIONS WITHIN I MILE OF THE SITEU U.Z U.4 U _ _ _ _ _MAP 8.1Three Mile Island Nuclear StationLocations of Radiological Environmental Monitoring Program StationsWithin I Mile of the Site CY-TM-170-300 Revision 3Page 189 of 209MAP 8.2THREE MILE ISLAND NUCLEAR STATIONLOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAMSTATIONS WITHIN 5 MILES OF THE SITEMAP 8.2Three Mile Island Nuclear StationLocations of Radiological Environmental Monitoring Program StationsWithin 5 Miles of the Site CY-TM-170-300 Revision 3Page 190 of 209MAP 8.3THREE MILE ISLAND NUCLEAR STATIONLOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAMSTATIONS GREATER THAN 5 MILES FROM THE SITEMAP 8.3Three Mile Island Nuclear StationLocations of Radiological Environmental Monitoring Program StationsGreater Than 5 Miles from the Site CY-TM-1 70-300Revision 3Page 191 of 2099.0 PART Ill REFERENCES
CY-TM-170-300 Revision 3 Page 193 of 209 PART IV REPORTING REQUIREMENTS CY-TM-1 70-300 Revision 3 Page 194 of 209 PART IV Reporting Requirements 1.0 TMI ANNUAL RADIOLOGICAL ENVIRONMENTAL OPERATING REPORT 1.1 Routine Radiological Environmental Operating Reports covering the operation of the unit during the previous calendar year shall be submitted to the Commission prior to May 1 of each year.1.2 The Annual Radiological Environmental Operating Reports shall include summaries, interpretations, and an analysis of trends of the results of the radiological environmental monitoring activities for the report period, including a comparison with prE-operational studies, with operational controls as appropriate, and with previous environmental monitoring reports, and an assessment of the observed impacts of the plant operation on the environment.
: 1. EPRI NP-3840, RP 1560-3 Final Report, "Environmental Radiation Doses FromDifficult-To-Measure Nuclides,"
The reports shall also include the results of Land Use Censuses required by Part III, Section 8.2.1.3 The Annual Radiological Environmental Operating Reports shall include the summarized tabulated results of analysis of all radiological environmental samples and environmental radiation measurements required by Part III Table 8.1 taken during the period pursuant to the locations specified in the tables and figures in this ODCM, as well as summarized and tabulated results of these analyses and measurements in a format similar to the table in the Radiological Assessment Branch Technical Position, Revision 1, November 1979. In the event that some individual results are not available for inclusion with the report, the report shall be submitted explaining the reasons for the missing results. The missing data shall be submitted as soon as possible in a supplementary report.1.4 The reports shall also include the following:
January 19852. "Evaluation of the Three Mile Island Nuclear Station Unit 1 to Demonstrate Conformance to the Design Objectives of 10 CFR 50, Appendix I," NuclearSafety Associates, May 19763. TMI-1 Final Safety Analysis Report (FSAR)4. TMI-2 Final Safety Analysis Report (FSAR)5. Meteorological Information and Dose Assessment System (MIDAS)6. NUREG-0017, "Calculation of Releases of Radioactive Materials in Gaseous andLiquid Effluents from PWR," Revision 1, 19857. NUREG-0133, "Preparation of Radiological Effluent Technical Specifications forNuclear Power Plants,"
A summary description of the radiological environments monitoring program; a map(s) of all sampling locations keyed to a table giving distances and directions from a point that is midway between the Reactor Buildings of TMI-1 and TMI-2; the results of licensee participation in the Interlaboratory Comparison Program, required by Part Ill, Section 8.3; discussion of all deviations from the sampling schedule of Part III, Table 8.1; discussion of all the required analyses in which the LLD required by Part III, Table 8.3 was not achievable.
October 19788. NUREG-01 72, "AgE-Specific Radiation Dose Commitment Factors For A OnE-Year Chronic Intake,"
November 19779. Regulatory Guide 1.21, "Measuring, Evaluating, and Reporting Radioactivity inSolid Wastes and Releases of Radioactive Materials in Liquid and GaseousEffluents from Light-Water Cooled Nuclear Power Plants,"
Revision 1, June 197410. Regulatory Guide 1.109, "Calculation of Annual Doses to Man from RoutineReleases of Reactor Effluents for the Purpose of Evaluating Compliance with 10CFR 50, Appendix I," Revision 1, October 197711. Simplified Environmental Effluent Dosimetry System (SEEDS)12. TMI Recirculation Factor Memos, April 12, 1988 and March 17, 198813. TMI-1 Operations Procedure, 1101-2.1, "Radiation Monitor Set Points"14. Title 10, Code of Federal Regulations, "Energy"15. TMI-1 Technical Specifications, attached to Facility Operating LicenseNo. DPR-5016. Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport andDispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors,"
Revision 1, July 197717. TMI-2 PDMS Technical Specifications, attached to Facility License No. DPR-73 CY-TM-1 70-300Revision 3Page 192 of 20918. Radiological Assessment Branch Technical Position on Environmental Monitoring, Revision 1, November 197919. Title 40, Code of Federal Regulations, "Protection of Environment"
: 20. Regulatory Guide 4.13, "Performance,  
: Testing, and Procedural Specifications forThermoluminescence Dosimetry:
Environmental Applications,"
Revision 1, July197721. Post-Defueling Monitored Storage Safety Analysis Report (PDMS SAR)
CY-TM-170-300 Revision 3Page 193 of 209PART IVREPORTING REQUIREMENTS CY-TM-1 70-300Revision 3Page 194 of 209PART IVReporting Requirements 1.0 TMI ANNUAL RADIOLOGICAL ENVIRONMENTAL OPERATING REPORT1.1 Routine Radiological Environmental Operating Reports covering the operation ofthe unit during the previous calendar year shall be submitted to the Commission prior to May 1 of each year.1.2 The Annual Radiological Environmental Operating Reports shall includesummaries, interpretations, and an analysis of trends of the results of theradiological environmental monitoring activities for the report period, including acomparison with prE-operational  
: studies, with operational controls asappropriate, and with previous environmental monitoring  
: reports, and anassessment of the observed impacts of the plant operation on the environment.
The reports shall also include the results of Land Use Censuses required by PartIII, Section 8.2.1.3 The Annual Radiological Environmental Operating Reports shall include thesummarized tabulated results of analysis of all radiological environmental samples and environmental radiation measurements required by Part IIITable 8.1 taken during the period pursuant to the locations specified in the tablesand figures in this ODCM, as well as summarized and tabulated results of theseanalyses and measurements in a format similar to the table in the Radiological Assessment Branch Technical  
: Position, Revision 1, November 1979. In theevent that some individual results are not available for inclusion with the report,the report shall be submitted explaining the reasons for the missing results.
Themissing data shall be submitted as soon as possible in a supplementary report.1.4 The reports shall also include the following:
A summary description of theradiological environments monitoring program; a map(s) of all sampling locations keyed to a table giving distances and directions from a point that is midwaybetween the Reactor Buildings of TMI-1 and TMI-2; the results of licenseeparticipation in the Interlaboratory Comparison  
: Program, required by Part Ill,Section 8.3; discussion of all deviations from the sampling schedule of Part III,Table 8.1; discussion of all the required analyses in which the LLD required byPart III, Table 8.3 was not achievable.
A single submittal may be made for the station.
A single submittal may be made for the station.
CY-TM-1 70-300Revision 3Page 195 of 2092.0 TMI ANNUAL RADIOACTIVE EFFLUENT RELEASE REPORTNOTE: A single submittal may be made for the station.
CY-TM-1 70-300 Revision 3 Page 195 of 209 2.0 TMI ANNUAL RADIOACTIVE EFFLUENT RELEASE REPORT NOTE: A single submittal may be made for the station. The submittal should combine those sections that are common to both units at the station however, for units with separate radwaste systems, the submittal shall specify the release of radioactive material from each unit.2.1 Routine Radioactive Effluent Release Reports covering the operations of the unit during the previous 12 months of operation shall be submitted prior to May 1 for TMI-1 and TMI-2.2.2 The following information shall be included in both Radioactive Effluent Release Reports to be submitted each year: The Radioactive Effluent Release Reports shall include a summary of the quantities of radioactive liquid and gaseous effluents and solid waste released from the unit as outlined in Reg. Guide 1.21, Rev. 1, with data summarized on a quarterly basis following the format of Appendix B thereof.2.3 The Radioactive Effluent Release Reports shall include the following information for each type of solid waste shipped offsite during the report period: a. Container volume b. Total curie quantity (specify whether determined by measurement or estimate)c. Principal radionuclides (specify whether determined by measurement or estimate)d. Type of waste (e.g., spent resin, compacted dry waste, evaporator bottoms)e. Type of shipment (e.g., Isa, type a, type b) and f. Solidification agent (e.g., cement)2.4 The Radioactive Effluent Release Reports shall include a summary of unplanned releases from the site to unrestricted areas of radioactive materials in gaseous and liquid effluents made during the reporting period.2.5 The Radioactive Effluent Release Reports shall include any changes made during the reporting period to the PROCESS CONTROL PROGRAM (PCP)documents and to the OFFSITE DOSE CALCULATION MANUAL (ODCM), as well as a listing of new locations for dose calculations and/or environmental monitoring identified by the land use census pursuant to Part III Section 8.2.
The submittal should combine those sections that are common to both units atthe station however, for units with separate radwaste systems,the submittal shall specify the release of radioactive materialfrom each unit.2.1 Routine Radioactive Effluent Release Reports covering the operations of the unitduring the previous 12 months of operation shall be submitted prior to May 1 forTMI-1 and TMI-2.2.2 The following information shall be included in both Radioactive Effluent ReleaseReports to be submitted each year:The Radioactive Effluent Release Reports shall include a summary of thequantities of radioactive liquid and gaseous effluents and solid waste releasedfrom the unit as outlined in Reg. Guide 1.21, Rev. 1, with data summarized on aquarterly basis following the format of Appendix B thereof.2.3 The Radioactive Effluent Release Reports shall include the following information for each type of solid waste shipped offsite during the report period:a. Container volumeb. Total curie quantity (specify whether determined by measurement orestimate)
CY-TM-1 70-300 Revision 3 Page 196 of 209 2.6 The Radioactive Effluent Release Reports shall include the instrumentation not returned to OPERABLE status within 30 days per ODCM Part I Controls 2.1.1 b and 2.1.2b, and ODCM Part II Control 2.1.2b.2.7 The Radioactive Effluent Release Report to be submitted shall include an annual summary of hourly meteorological data collected over the previous year. This annual summary may be either in the form of an hour-by-hour listing of wind speed, wind direction, atmosphere stability, and precipitation (if measured) on magnetic tape, or in the form of joint frequency distribution of wind speed, wind direction, and atmospheric stability.
: c. Principal radionuclides (specify whether determined by measurement orestimate)
2.8 The Radioactive Effluent Release Report shall include an assessment of the radiation doses to MEMBERS OF THE PUBLIC due to the radioactive liquid and gaseous effluents released from the unit or station during the previous calendar year. The meteorological conditions concurrent with the time of release of radioactive materials in gaseous effluents (as determined by sampling frequency and measurement) shall be used for determining the gaseous pathway doses.The assessment of radiation doses shall be performed in accordance with this ODCM.2.9 The Radioactive Effluent Release Report shall include an assessment of the radiation doses from radioactive liquid and gaseous effluents to MEMBERS OF THE PUBLIC due to their activities inside the SITE BOUNDARY during the report period, to verify compliance with the limits of 1OCFR20.1301 (a)(1). All assumptions used in making these assessments (i.e., specific activity, exposure time and location) shall be included in these reports.2.10 The Radioactive Effluent Release Report shall also include an assessment of radiation doses to the likely most exposed real individual from reactor releases, and other nearby uranium fuel cycle sources, including doses from primary effluent pathways and direct radiation for the previous 12 consecutive months, to show conformance with 40 CFR 190 "Environmental Radiation Protection Standards for Nuclear Power Operation." Acceptable methods for calculating the dose contributions from liquid and gaseous effluents are given in Regulatory Guide 1.109, Rev. 1.
: d. Type of waste (e.g., spent resin, compacted dry waste, evaporator bottoms)e. Type of shipment (e.g., Isa, type a, type b) andf. Solidification agent (e.g., cement)2.4 The Radioactive Effluent Release Reports shall include a summary of unplanned releases from the site to unrestricted areas of radioactive materials in gaseousand liquid effluents made during the reporting period.2.5 The Radioactive Effluent Release Reports shall include any changes madeduring the reporting period to the PROCESS CONTROL PROGRAM (PCP)documents and to the OFFSITE DOSE CALCULATION MANUAL (ODCM), aswell as a listing of new locations for dose calculations and/or environmental monitoring identified by the land use census pursuant to Part III Section 8.2.
CY-TM-1 70-300 Revision 3 Page 197 of 209 3.0 PART IV REFERENCES 3.1 Radiological Assessment Branch Technical Position, Revision 1, November 1979 3.2 Regulatory Guide 1.21, "Measuring, Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive Materials in Liquid and Gaseous Effluents from Light-Water-Cooled Nuclear Power Plants," Revision 1, June 1974 3.3 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-50 3.4 Title 40, Code of Federal Regulations, "Protection of Environment" 3.5 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977 3.6 Title 10, Code of Federal Regulations, "Energy" 3.7 Regulatory Guide 1.111, "Methods of Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors," Revision 1, July 1977 3.8 Regulatory Guide 1.112, "Calculation of Releases of Radioactive Materials in Gaseous and Liquid Effluents from Light-Water-Cooled Power Reactors," Revision O-R, April 1976 3.9 Regulatory Guide 1.113, "Estimating Aquatic Dispersion of Effluents from Accidental and Routine Reactor Releases for the Purpose of Implementing Appendix I," Revision 1, April 1977 CY-TM-1 70-300 Revision 3 Page 198 of 209 APPENDIX A Page 1 of 1 P, -Pathway Dose Rate Parameter P, (inhalation)  
CY-TM-1 70-300Revision 3Page 196 of 2092.6 The Radioactive Effluent Release Reports shall include the instrumentation notreturned to OPERABLE status within 30 days per ODCM Part I Controls 2.1.1 band 2.1.2b, and ODCM Part II Control 2.1.2b.2.7 The Radioactive Effluent Release Report to be submitted shall include an annualsummary of hourly meteorological data collected over the previous year. Thisannual summary may be either in the form of an hour-by-hour listing of windspeed, wind direction, atmosphere stability, and precipitation (if measured) onmagnetic tape, or in the form of joint frequency distribution of wind speed, winddirection, and atmospheric stability.
= k' (BR) DFAI (Eq A-I)Where: Pi = the pathway dose rate parameter for radionuclide,-
2.8 The Radioactive Effluent Release Report shall include an assessment of theradiation doses to MEMBERS OF THE PUBLIC due to the radioactive liquid andgaseous effluents released from the unit or station during the previous calendaryear. The meteorological conditions concurrent with the time of release ofradioactive materials in gaseous effluents (as determined by sampling frequency and measurement) shall be used for determining the gaseous pathway doses.The assessment of radiation doses shall be performed in accordance with thisODCM.2.9 The Radioactive Effluent Release Report shall include an assessment of theradiation doses from radioactive liquid and gaseous effluents to MEMBERS OFTHE PUBLIC due to their activities inside the SITE BOUNDARY during the reportperiod, to verify compliance with the limits of 1OCFR20.1301 (a)(1). Allassumptions used in making these assessments (i.e., specific  
i, (other than noble gases) for the inhalation pathway, in mrem/yr per microcurie/m 3.The dose factors are based on the critical individual organ for the child age group.k' = conversion factor, 1 E6 pCi/microcurie BR = 3700 m 3/yr, breathing rate for child (Reg. Guide 1.109, Rev. 1, Table E-5)DFA= = the maximum organ inhalation dose factor for the infant age group for the ith adionuclide (mRem/pCi).
: activity, exposuretime and location) shall be included in these reports.2.10 The Radioactive Effluent Release Report shall also include an assessment ofradiation doses to the likely most exposed real individual from reactor releases, and other nearby uranium fuel cycle sources, including doses from primaryeffluent pathways and direct radiation for the previous 12 consecutive months, toshow conformance with 40 CFR 190 "Environmental Radiation Protection Standards for Nuclear Power Operation."
Values are taken from Table E-10, Reg. Guide 1.109 (Rev. 1), or NUREG-01 72.Resolution of the units yields: (ODCM Part III Table 4.6)Pi (inhalation)  
Acceptable methods for calculating thedose contributions from liquid and gaseous effluents are given in Regulatory Guide 1.109, Rev. 1.
= 3.7E9 DFAI (mrem/yr per PCi/m 3) (Eq A-2)NOTE: The latest NRC Guidance has deleted the requirement to determine Pi (ground plane) and Pi (food). In addition, the critical age group has been changed from infant to child.
CY-TM-1 70-300Revision 3Page 197 of 2093.0 PART IV REFERENCES 3.1 Radiological Assessment Branch Technical  
CY-TM-1 70-300 Revision 3 Page 199 of 209 APPENDIX B Page 1 of I R, -Inhalation Pathway Dose Factor R1 = k' (BR) (DFAi,a,o) (mrem/yr per microcurie/m
: Position, Revision 1, November 19793.2 Regulatory Guide 1.21, "Measuring, Evaluating, and Reporting Radioactivity inSolid Wastes and Releases of Radioactive Materials in Liquid and GaseousEffluents from Light-Water-Cooled Nuclear Power Plants,"
: 3) (Eq B-I)Where: k' = conversion factor, 1 E6 pCi/microcurie BR = breathing rate, 1400, 3700, 8000, 8000 m 3/yr for infant, child, teenager, and adult age groups, respectively. (Reg. Guide 1.109, Rev. 1, Table E-5)DFAi,a,o = the inhalation dose factor for organ, o, of the receptor of a given age group, a, and for the ith radionuclide, in mrem/pCi.
Revision 1, June 19743.3 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-503.4 Title 40, Code of Federal Regulations, "Protection of Environment" 3.5 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from RoutineReleases of Reactor Effluents for the Purpose of Evaluating Compliance with 10CFR Part 50, Appendix I," Revision 1, October 19773.6 Title 10, Code of Federal Regulations, "Energy"3.7 Regulatory Guide 1.111, "Methods of Estimating Atmospheric Transport andDispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors,"
The total body is considered as an organ in the selection of DFAi,ao. Values are taken from Tables E-7 through E-10, Reg. Guide 1.109 (Rev. 1), or NUREG 0172.Resolutions of the units yields: R, = (1.4E9) (DFAi,a,o) infant (ODCM Part III Table 5.2.1)R1 = (3.7E9) (DFAi,a,o) child (ODCM Part III Table 5.2.2)Rj = (8.0E9) (DFAi,ao) teen and adult (ODCM Part III Tables 5.2.3 and 5.2.4)
Revision 1, July 19773.8 Regulatory Guide 1.112, "Calculation of Releases of Radioactive Materials inGaseous and Liquid Effluents from Light-Water-Cooled Power Reactors,"
CY-TM-1 70-300 Revision 3 Page 200 of 209 APPENDIX C Page 1 of 1 R, -Ground Plane Pathway Dose Factor R, = k' k" (SF) (DFGj) [(1-e "it)/X 1] (Eq C-1)Where: k' = conversion factor, 1 E6 pCi/microcurie k" = conversion factor, 8760 hr/yr= decay constant for the ith radionuclide, sec t = the exposure time (this calculation assumes that decay is the only operating removal mechanism) 4.73 x 108 sec. (15 yrs), Reg. Guide 1.109 (Rev. 1), Appendix C DFG 1 = the ground plane dose conversion factor for the ith radionuclide (mrem/hr per pCi/m 2). Values are taken from Table E-6, Reg. Guide 1.109 (Rev. 1), or NUREG 0172. These values apply to all age groups.SF = 0.7, shielding factor, from Table E-15 Reg. Guide 1.109 (Rev'. 1)Reference ODCM Part III Table 5.3.1 CY-TM-170-300 Revision 3 Page 201 of 209 APPENDIX D Page 1 of 2 R, -Grass Cow-Milk Pathway Dose Factor Rim k' [(QF X UAP) / (Xi + Xw)] x (Fo) x (r) x (DFLi,a,o) x[((fp x fs)/Yp) + ((I-fp x fs) e -ith)IYs]
Revision O-R, April 19763.9 Regulatory Guide 1.113, "Estimating Aquatic Dispersion of Effluents fromAccidental and Routine Reactor Releases for the Purpose of Implementing Appendix I," Revision 1, April 1977 CY-TM-1 70-300Revision 3Page 198 of 209APPENDIX APage 1 of 1P, -Pathway Dose Rate Parameter P, (inhalation)  
E-Xitf (Eq D-1)Where: k' = conversion factor, 1 E6 picocurie/microcurie (pCi/lgci)
= k' (BR) DFAI (Eq A-I)Where:Pi = the pathway dose rate parameter for radionuclide,-
QF = cow consumption rate, 50 kg/day, (Reg. Guide 1.109, Rev. 1)goat consumption rate, 6 kg/day, (Reg. Guide 1.109, Rev. 1, Table E-2)UAP = Receptor's milk consumption rate; 330, 330, 400, 310 liters/yr for infant, child, teenager, and adult age groups, respectively (Reg. Guide 1.109, Rev. 1)Yp = agricultural productivity by unit area of pasture feed grass, 0.7 kg/M 2 (NUREG-0133)
i, (other than noble gases) for theinhalation
Ys = agricultural productivity by unit area of stored feed, 2.0 kg/M 2 (NUREG-0133)
: pathway, in mrem/yr per microcurie/m 3.The dose factors are based onthe critical individual organ for the child age group.k' = conversion factor, 1 E6 pCi/microcurie BR = 3700 m3/yr, breathing rate for child (Reg. Guide 1.109, Rev. 1, Table E-5)DFA= = the maximum organ inhalation dose factor for the infant age group for the ithadionuclide (mRem/pCi).
Fm = stable element transfer coefficient (Table E-1, Reg. Guide 1.109, Rev. 1)r = fraction of deposited activity retained in cow's feed grass, 0.2 for particulates, 1.0 for radioiodine (Table E-15, Reg. Guide 1.109, Rev. 1)DFLi,a,o = the ingestion dose factor for organ, o, and the ith radionuclide for each respective age group, a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.ki = decay constant for the ith radionuclide, sec-1;L, = decay constant for weathering, 5.73 x 10-7 sec-1 (NUREG-0133);
Values are taken from Table E-10, Reg. Guide 1.109(Rev. 1), or NUREG-01 72.Resolution of the units yields: (ODCM Part III Table 4.6)Pi (inhalation)  
based on a 14 day half life tf = 1.73 x 105 sec, the transport time from pasture to cow to milk to receptor (Table E-15, Reg. Guide 1.109, Rev. 1), or 2 days th = 7.78 x 106 sec, the transport time from pasture to harvest to cow to milk to receptor (Table E-15, Reg. Guide 1.109, Rev. 1), or 90 days fp = 1.0, the fraction of the year that the cow is on pasture fs = 1.0, the fraction of the cow feed that is pasture grass while the cow is on pasture CY-TM-1 70-300 Revision 3 Page 202 of 209 APPENDIX D Page 2 of 2 The concentration of tritium in milk is based on the airborne concentration rather than the deposition.
= 3.7E9 DFAI (mrem/yr per PCi/m3) (Eq A-2)NOTE: The latest NRC Guidance has deleted the requirement todetermine Pi (ground plane) and Pi (food). In addition, thecritical age group has been changed from infant to child.
Therefore, Ri is based on (X/Q): Rct,a,o = k'k"' Fm QF UApDFLt,a,o  
CY-TM-1 70-300Revision 3Page 199 of 209APPENDIX BPage 1 of IR, -Inhalation Pathway Dose FactorR1 = k' (BR) (DFAi,a,o)  
(.75 [.5/HI) (Eq D-2)Where: k"' = 1E3 grams/kg H = 8 grams/m 3 , absolute humidity of the atmosphere
(mrem/yr per microcurie/m
.75 = fraction of the total feed grass mass that is water.5 = ratio of the specific activity of the feed grass water to the atmospheric water (NUREG-0133)
: 3) (Eq B-I)Where:k' = conversion factor, 1 E6 pCi/microcurie BR = breathing rate, 1400, 3700, 8000, 8000 m3/yr for infant, child, teenager, and adultage groups, respectively.  
DFLt,a,o = the ingestion dose factor for tritium and organ, o, for each respective age group, a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.All other parameters and values are as given above.NOTE: Goat-milk pathway factor, Ri, will be computed using the cow-milk pathway factor equation.
(Reg. Guide 1.109, Rev. 1, Table E-5)DFAi,a,o  
Fm factor for goat-milk will be from Table E-2 Reg. Guide 1.109, Rev. 1.
= the inhalation dose factor for organ, o, of the receptor of a given age group, a,and for the ith radionuclide, in mrem/pCi.
The total body is considered as anorgan in the selection of DFAi,ao.
Values are taken from Tables E-7 through E-10, Reg. Guide 1.109 (Rev. 1), or NUREG 0172.Resolutions of the units yields:R, = (1.4E9) (DFAi,a,o) infant (ODCM Part III Table 5.2.1)R1 = (3.7E9) (DFAi,a,o) child (ODCM Part III Table 5.2.2)Rj = (8.0E9) (DFAi,ao) teen and adult (ODCM Part III Tables 5.2.3 and 5.2.4)
CY-TM-1 70-300Revision 3Page 200 of 209APPENDIX CPage 1 of 1R, -Ground Plane Pathway Dose FactorR, = k' k" (SF) (DFGj) [(1-e "it)/X1] (Eq C-1)Where:k' = conversion factor, 1 E6 pCi/microcurie k" = conversion factor, 8760 hr/yr= decay constant for the ith radionuclide, sect = the exposure time (this calculation assumes that decay is the only operating removal mechanism) 4.73 x 108 sec. (15 yrs), Reg. Guide 1.109 (Rev. 1),Appendix CDFG1 = the ground plane dose conversion factor for the ith radionuclide (mrem/hr perpCi/m2). Values are taken from Table E-6, Reg. Guide 1.109 (Rev. 1), orNUREG 0172. These values apply to all age groups.SF = 0.7, shielding factor, from Table E-15 Reg. Guide 1.109 (Rev'. 1)Reference ODCM Part III Table 5.3.1 CY-TM-170-300 Revision 3Page 201 of 209APPENDIX DPage 1 of 2R, -Grass Cow-Milk Pathway Dose FactorRim k' [(QF X UAP) / (Xi + Xw)] x (Fo) x (r) x (DFLi,a,o) x[((fp x fs)/Yp) + ((I-fp x fs) e -ith)IYs]
E-Xitf (Eq D-1)Where:k' = conversion factor, 1 E6 picocurie/microcurie (pCi/lgci)
QF = cow consumption rate, 50 kg/day, (Reg. Guide 1.109, Rev. 1)goat consumption rate, 6 kg/day, (Reg. Guide 1.109, Rev. 1, Table E-2)UAP = Receptor's milk consumption rate; 330, 330, 400, 310 liters/yr for infant, child,teenager, and adult age groups, respectively (Reg. Guide 1.109, Rev. 1)Yp = agricultural productivity by unit area of pasture feed grass, 0.7 kg/M2(NUREG-0133)
Ys = agricultural productivity by unit area of stored feed, 2.0 kg/M2 (NUREG-0133)
Fm = stable element transfer coefficient (Table E-1, Reg. Guide 1.109, Rev. 1)r = fraction of deposited activity retained in cow's feed grass, 0.2 for particulates, 1.0for radioiodine (Table E-15, Reg. Guide 1.109, Rev. 1)DFLi,a,o  
= the ingestion dose factor for organ, o, and the ith radionuclide for each respective age group, a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.ki = decay constant for the ith radionuclide, sec-1;L, = decay constant for weathering, 5.73 x 10-7 sec-1 (NUREG-0133);
based on a 14day half lifetf = 1.73 x 105 sec, the transport time from pasture to cow to milk to receptor (TableE-15, Reg. Guide 1.109, Rev. 1), or 2 daysth = 7.78 x 106 sec, the transport time from pasture to harvest to cow to milk toreceptor (Table E-15, Reg. Guide 1.109, Rev. 1), or 90 daysfp = 1.0, the fraction of the year that the cow is on pasturefs = 1.0, the fraction of the cow feed that is pasture grass while the cow is on pasture CY-TM-1 70-300Revision 3Page 202 of 209APPENDIX DPage 2 of 2The concentration of tritium in milk is based on the airborne concentration rather than thedeposition.
Therefore, Ri is based on (X/Q):Rct,a,o = k'k"' Fm QF UApDFLt,a,o  
(.75 [.5/HI) (Eq D-2)Where:k"' = 1E3 grams/kgH = 8 grams/m3, absolute humidity of the atmosphere
.75 = fraction of the total feed grass mass that is water.5 = ratio of the specific activity of the feed grass water to the atmospheric water(NUREG-0133)
DFLt,a,o  
= the ingestion dose factor for tritium and organ, o, for each respective age group,a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.All other parameters and values are as given above.NOTE: Goat-milk pathway factor, Ri, will be computed using thecow-milk pathway factor equation.
Fm factor for goat-milk will befrom Table E-2 Reg. Guide 1.109, Rev. 1.


==Reference:==
==Reference:==


ODCM Part III Tables 5.4.1 to 5.4.4 CY-TM-1 70-300Revision 3Page 203 of 209APPENDIX EPage 1 of 2R, -Cow-Meat Pathway Dose FactorRi= k' [(QF X UAP) I (Xi+ X (Ff) x (r) x (DFLi,a,o) x[((fp x fs)/Yp) + ((I-fpfs) e "'ith)/Ys]
ODCM Part III Tables 5.4.1 to 5.4.4 CY-TM-1 70-300 Revision 3 Page 203 of 209 APPENDIX E Page 1 of 2 R, -Cow-Meat Pathway Dose Factor Ri= k' [(QF X UAP) I (Xi+ X (Ff) x (r) x (DFLi,a,o) x[((fp x fs)/Yp) + ((I-fpfs) e "'ith)/Ys]
x E-xitf (Eq E-1)Where:k' = conversion factor, 1 E6 picocurie/microcurie (pCi/gci)
x E-xitf (Eq E-1)Where: k' = conversion factor, 1 E6 picocurie/microcurie (pCi/gci)QF = cow consumption rate, 50 kg/day, (Reg. Guide 1.109, Rev. 1)UAP = Receptor's meat consumption rate; 0, 41, 65, 110 kg/yr for infant, child, teenager, and adult age groups, respectively (Reg. Guide 1.109, Rev. 1)Ff = the stable element transfer coefficients, days/kg (Table E-1, Reg. Guide 1.109, Rev. 1)r = fraction of deposited activity retained in cow's feed grass, 0.2 for particulates, 1.0 for radioiodine (Table E-15, Reg. Guide 1.109, Rev. 1)DFLi,a,o = the ingestion dose factor for organ, o, and the ith radionuclide for each respective age group, a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.XI = decay constant for the radionuclide i, sec1 X, = decay constant for weathering, 5.73 x 10- sec1 (NUREG-0133), based on a 14 day half life tf = 1.73 x 106 sec, the transport time from pasture to receptor (NUREG-01 33)th = 7.78 X 106 sec, the transport time from crop to receptor (NUREG-01 33)Yp = agricultural productivity by unit area of pasture feed grass, 0.7 kg/M 2 (NUREG-0133)
QF = cow consumption rate, 50 kg/day, (Reg. Guide 1.109, Rev. 1)UAP = Receptor's meat consumption rate; 0, 41, 65, 110 kg/yr for infant, child, teenager, and adult age groups, respectively (Reg. Guide 1.109, Rev. 1)Ff = the stable element transfer coefficients, days/kg (Table E-1, Reg. Guide 1.109,Rev. 1)r = fraction of deposited activity retained in cow's feed grass, 0.2 for particulates, 1.0for radioiodine (Table E-15, Reg. Guide 1.109, Rev. 1)DFLi,a,o  
Ys = agricultural productivity by unit area of stored feed, 2.0 kg/M 2 (NUREG-0133) fp = 1.0, the fraction of the year that the cow is on pasture fs = 1.0, the fraction of the cow feed that is pasture grass while the cow is on pasture CY-TM-1 70-300 Revision 3 Page 204 of 209 APPENDIX E PAGE 2 OF 2 The concentration of tritium in meat is based on the airborne concentration rather than the deposition.
= the ingestion dose factor for organ, o, and the ith radionuclide for each respective age group, a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.XI = decay constant for the radionuclide i, sec1X, = decay constant for weathering, 5.73 x 10- sec1 (NUREG-0133),
Therefore, Ri is based on (X/Q): Rt,a,o = k'k'" Ff QF UAP (DFLt,a,o) x 0.75 x (0.5/H]) (Eq E-2)Where: All terms are as defined above and in Appendix D.
based on a 14day half lifetf = 1.73 x 106 sec, the transport time from pasture to receptor (NUREG-01 33)th = 7.78 X 106 sec, the transport time from crop to receptor (NUREG-01 33)Yp = agricultural productivity by unit area of pasture feed grass, 0.7 kg/M2(NUREG-0133)
Ys = agricultural productivity by unit area of stored feed, 2.0 kg/M2 (NUREG-0133) fp = 1.0, the fraction of the year that the cow is on pasturefs = 1.0, the fraction of the cow feed that is pasture grass while the cow is on pasture CY-TM-1 70-300Revision 3Page 204 of 209APPENDIX EPAGE 2 OF 2The concentration of tritium in meat is based on the airborne concentration rather than thedeposition.
Therefore, Ri is based on (X/Q):Rt,a,o = k'k'" Ff QF UAP (DFLt,a,o) x 0.75 x (0.5/H])  
(Eq E-2)Where:All terms are as defined above and in Appendix D.


==Reference:==
==Reference:==


ODCM Part III, Tables 5.6.1 to 5.6.4 CY-TM-170-300 Revision 3Page 205 of 209APPENDIX FPAGE 1 OF IR, -Vegetation Pathway Dose FactorR, k' x [r/ (Y, (k, + kw))] x (DFLi,a,o)
ODCM Part III, Tables 5.6.1 to 5.6.4 CY-TM-170-300 Revision 3 Page 205 of 209 APPENDIX F PAGE 1 OF I R, -Vegetation Pathway Dose Factor R, k' x [r/ (Y, (k, + kw))] x (DFLi,a,o)
X [(ULA) fL E'XitL + USA fg E-'ith] (Eq F-1)Where:k' = 1 E6 picocurie/microcurie (pCi/jLci)
X [(ULA) fL E'XitL + USA fg E-'ith] (Eq F-1)Where: k' = 1 E6 picocurie/microcurie (pCi/jLci)
ULA = the consumption rate of fresh leafy vegetation, 0, 26, 42, 64 kg/yr for infant, child,teenager, or adult age groups, respectively (Reg. Guide 1.109, Rev. 1)UsA = the consumption rate of stored vegetation, 0, 520, 630, 520 kg/yr for infant, child,teenager, or adult age groups respectively (Reg. Guide 1.109, Rev. 1)fL = the fraction of the annual intake of fresh leafy vegetation grown locally,  
ULA = the consumption rate of fresh leafy vegetation, 0, 26, 42, 64 kg/yr for infant, child, teenager, or adult age groups, respectively (Reg. Guide 1.109, Rev. 1)UsA = the consumption rate of stored vegetation, 0, 520, 630, 520 kg/yr for infant, child, teenager, or adult age groups respectively (Reg. Guide 1.109, Rev. 1)fL = the fraction of the annual intake of fresh leafy vegetation grown locally, = 1.0 (NUREG-0133) fg = the fraction of the stored vegetation grown locally = 0.76 (NUREG-0133) tL = the average time between harvest of leafy vegetation and its consumption, 8.6 x 104 seconds [Table E-15, Reg. Guide 1.109, Rev. 1 (24 hrs)]th = the average time between harvest of stored leafy vegetation and its consumption, 5.18 x 10 seconds, [Table E-15, Reg. Guide 1.109, Rev. 1 (60 days)]yv = the vegetation area density, 2.0 kg/mi 2 (Table E-15, Reg. Guide 1.109, Rev. 1)All other parameters are as previously defined.The concentration of tritium in vegetation is based on the airborne concentration rather than the deposition.
= 1.0(NUREG-0133) fg = the fraction of the stored vegetation grown locally = 0.76 (NUREG-0133) tL = the average time between harvest of leafy vegetation and its consumption, 8.6 x104 seconds [Table E-15, Reg. Guide 1.109, Rev. 1 (24 hrs)]th = the average time between harvest of stored leafy vegetation and its consumption, 5.18 x 10 seconds,  
[Table E-15, Reg. Guide 1.109, Rev. 1 (60 days)]yv = the vegetation area density, 2.0 kg/mi2 (Table E-15, Reg. Guide 1.109, Rev. 1)All other parameters are as previously defined.The concentration of tritium in vegetation is based on the airborne concentration rather thanthe deposition.
Therefore, Ri is based on (X/Q)Rt,a,o = k'k"' [ULA fL + USA fg] (DFLt,a,o)  
Therefore, Ri is based on (X/Q)Rt,a,o = k'k"' [ULA fL + USA fg] (DFLt,a,o)  
(.75 [.5/1H])  
(.75 [.5/1H]) (Eq F-2)Where: All terms are as defined above and in Appendix D.
(Eq F-2)Where:All terms are as defined above and in Appendix D.


==Reference:==
==Reference:==


ODCM Part III, Tables 5.7.1 to 5.7.4 CY-TM-1 70-300Revision 3Page 206 of 209APPENDIX A-F REFERENCES (Page 1 of 4)Parameters Used in Dose Factor Calculations Origin of ValueTable in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 SpecificFor Pi ***DFA, Each radionuclide E-9 Note 1BR 3700 m3/yr (child) E-5***For Ri (Vegetation)***
ODCM Part III, Tables 5.7.1 to 5.7.4 CY-TM-1 70-300 Revision 3 Page 206 of 209 APPENDIX A-F REFERENCES (Page 1 of 4)Parameters Used in Dose Factor Calculations Origin of Value Table in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 Specific For Pi ***DFA, Each radionuclide E-9 Note 1 BR 3700 m 3/yr (child) E-5***For Ri (Vegetation)***
r Each element type E-1Yv 2.0 kg/m2 E-15kw 5.73 E-7 sec' 5.3.1.3DFL1 Each age group and radionuclide E-1 1 thru E-14 Note 1UaL Each age group E-5fL 1.0 5.3.1.5tL 8.6 E + 4 seconds E-15Uas Each age group E-5fg 0.76 5.3.1.5th 5.18 E + 6 seconds E-15H 8.0 grams/kg 5.2.1.3***For Ri (Inhalation)***
r Each element type E-1 Yv 2.0 kg/m 2 E-15 kw 5.73 E-7 sec' 5.3.1.3 DFL 1 Each age group and radionuclide E-1 1 thru E-14 Note 1 UaL Each age group E-5 fL 1.0 5.3.1.5 tL 8.6 E + 4 seconds E-15 Uas Each age group E-5 fg 0.76 5.3.1.5 th 5.18 E + 6 seconds E-15 H 8.0 grams/kg 5.2.1.3***For Ri (Inhalation)***
BR Each age group E-5DFA, Each age group and nuclide E-7 thru E-10 Note 1 CY-TM-1 70-300Revision 3Page 207 of 209APPENDIX A-F REFERENCES (Page 2 of 4)Parameters Used in Dose Factor Calculations Origin of ValueTable in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 SpecificFor Ri (Ground Plane)SF 0.7 E-1 5DFGj Each radionuclide E-6t 4.73 E + 8 sec 5.3.1.2For R1 (Grass/Animal/Meat)
BR Each age group E-5 DFA, Each age group and nuclide E-7 thru E-10 Note 1 CY-TM-1 70-300 Revision 3 Page 207 of 209 APPENDIX A-F REFERENCES (Page 2 of 4)Parameters Used in Dose Factor Calculations Origin of Value Table in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 Specific For Ri (Ground Plane)SF 0.7 E-1 5 DFGj Each radionuclide E-6 t 4.73 E + 8 sec 5.3.1.2 For R 1 (Grass/Animal/Meat)
QF(COW) 50 kg/day E-3QF (Goat) 6 kg/day E-3 Ref. OnlyUap Each age group E-5xw 5.73 E-7 sec1 5.3.1.3Ff (Both) Each element E-1r Each element type E-15DFLI Each age group and nuclide E-1 1 thru E-14 Note 1fp 1.0 5.3.1.3 Note 2f 1.0 5.3.1.3 Note 2Yp 0.7 kg/m3 E-15th 7.78 E + 6 sec E-15Ys 2.0 kg/m2 E-15tf 1.73 E + 6 sec E-15H 8.0 grams/kg 5.2.1.3 CY-TM-1 70-300Revision 3Page 208 of 209APPENDIX A-F REFERENCES (Page 3 of 4)Parameters Used in Dose Factor Calculations Origin of ValueTable in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 SpecificFor R, (Grass/Cow/Milk)  
QF(COW) 50 kg/day E-3 QF (Goat) 6 kg/day E-3 Ref. Only Uap Each age group E-5 xw 5.73 E-7 sec 1 5.3.1.3 Ff (Both) Each element E-1 r Each element type E-15 DFLI Each age group and nuclide E-1 1 thru E-14 Note 1 fp 1.0 5.3.1.3 Note 2 f 1.0 5.3.1.3 Note 2 Yp 0.7 kg/m 3 E-15 th 7.78 E + 6 sec E-15 Ys 2.0 kg/m 2 E-15 tf 1.73 E + 6 sec E-15 H 8.0 grams/kg 5.2.1.3 CY-TM-1 70-300 Revision 3 Page 208 of 209 APPENDIX A-F REFERENCES (Page 3 of 4)Parameters Used in Dose Factor Calculations Origin of Value Table in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 Specific For R, (Grass/Cow/Milk)  
***Q, 50 kg/day E-3Uap Each age group E-5Xw 5.73 E-7 sec1 5.3.1.3Fm Each element E-1r Each element type E-1 5DFL1 Each age group and nuclide E-1 1 thru E-14 Note 1Yp 0.7 kg/mi2 E-15th 7.78 E + 6 sec E-15Ys 2.0 kg/M2 E-15tf 1.73 E + 5 sec E-15fp 1.0 5.3.1.3s 1.0 5.3.1.3H 8.0 grams/kg 5.2.1.3 CY-TM-1 70-300Revision 3Page 209 of 209APPENDIX A-F REFERENCES (Page 4 of 4)NOTES1. Inhalation and ingestion dose factors were taken from the indicated source. For eachage group, for each nuclide, the organ dose factor used was the highest dose factor forthat nuclide and age group in the referenced table.2. Typically, beef cattle are raised all year on pasture.
***Q, 50 kg/day E-3 Uap Each age group E-5 Xw 5.73 E-7 sec 1 5.3.1.3 Fm Each element E-1 r Each element type E-1 5 DFL 1 Each age group and nuclide E-1 1 thru E-14 Note 1 Yp 0.7 kg/mi 2 E-15 th 7.78 E + 6 sec E-15 Ys 2.0 kg/M 2 E-15 tf 1.73 E + 5 sec E-15 fp 1.0 5.3.1.3 s 1.0 5.3.1.3 H 8.0 grams/kg 5.2.1.3 CY-TM-1 70-300 Revision 3 Page 209 of 209 APPENDIX A-F REFERENCES (Page 4 of 4)NOTES 1. Inhalation and ingestion dose factors were taken from the indicated source. For each age group, for each nuclide, the organ dose factor used was the highest dose factor for that nuclide and age group in the referenced table.2. Typically, beef cattle are raised all year on pasture. Annual land surveys have indicated that the small number of goats raised within 5 miles, typically are used for grass control and not food or milk. Nevertheless, the goats can be treated as full meat sources where present, despite the fact that their numbers cannot sustain the meat consumption rates of Table E-5, NUREG-01 33.REFERENCES
Annual land surveys have indicated that the small number of goats raised within 5 miles, typically are used for grass controland not food or milk. Nevertheless, the goats can be treated as full meat sources wherepresent, despite the fact that their numbers cannot sustain the meat consumption ratesof Table E-5, NUREG-01 33.REFERENCES
: 1. Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977.2. TMI-1 Technical Specifications, attached to Facility Operating License No. DPR-50.3. NUREG-01 33, "Preparation of Radiological Effluent Technical Specifications for Nuclear Power Plants," October 1978.
: 1. Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases ofReactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50,Appendix I," Revision 1, October 1977.2. TMI-1 Technical Specifications, attached to Facility Operating License No. DPR-50.3. NUREG-01 33, "Preparation of Radiological Effluent Technical Specifications for NuclearPower Plants,"
50.59 APPLICABILITY REVIEW FORM Activity/Document Number: i -Revision Number: Title: .QC$ _ VZ(:_V ~/ ~Io LS-AA-104-1002 Revision 4 Page I of I I Address the questions below for all aspects of the Activity.
October 1978.
50.59 APPLICABILITY REVIEW FORMActivity/Document Number: i -Revision Number:Title: .QC$ _ VZ(:_V ~/ ~IoLS-AA-104-1002 Revision 4Page I of IIAddress the questions below for all aspects of the Activity.
If the answer is yes for any portion of the Activity, apply the identified process(es) to that portion of the Activity.
If the answer is yes for any portion of the Activity, apply the identified process(es) to that portion of the Activity.
Note that it is not unusual to have more than one process apply to a given Activity.
Note that it is not unusual to have more than one process apply to a given Activity.
SeeSection 4 of the Resource Manual (RM) for additional guidance.
See Section 4 of the Resource Manual (RM) for additional guidance.1. Does the proposed Activity involve a change: I. Technical Specifications or Facility Operating License (1OCFR50.90)?
: 1. Does the proposed Activity involve a change:I. Technical Specifications or Facility Operating License (1OCFR50.90)?
I NO [I YES See Section 4.2.1.1 of the RM 2. Conditions of License Quality Assurance program (1 OCFR50.54(a))?
I NO [I YES See Section 4.2.1.1 of the RM2. Conditions of LicenseQuality Assurance program (1 OCFR50.54(a))?
XNO C1 YES Security Plan (I OCFR50.54(p))?
XNO C1 YESSecurity Plan (I OCFR50.54(p))?
NO E] YES See Section 4.2.1.2 of the RM Emergency Plan (IOCFR50.54(q))?
NO E] YES See Section 4.2.1.2 of the RMEmergency Plan (IOCFR50.54(q))?
I NO [] YES 3. Codes and Standards IST Program Plan (IOCFR50.55a(O)?  
I NO [] YES3. Codes and Standards IST Program Plan (IOCFR50.55a(O)?  
[NO Dl YES See Section 4.2.1.3 of the RM ISI Program Plan (IOCFR50.55a(g))?  
[NO Dl YES See Section 4.2.1.3 of the RMISI Program Plan (IOCFR50.55a(g))?  
'NO El YES 4. ECCS Acceptance Criteria (IOCFR50.46)?
'NO El YES4. ECCS Acceptance Criteria (IOCFR50.46)?
PqNO El YES See Section 4.2.1.4 of the RM 5. Specific Exemptions (IOCFR50.12)?
PqNO El YES See Section 4.2.1.4 of the RM5. Specific Exemptions (IOCFR50.12)?
25NO E] YES See Section 4.2.1.5 of the RM 6. Radiation Protection Program (IOCFR20)?
25NO E] YES See Section 4.2.1.5 of the RM6. Radiation Protection Program (IOCFR20)?
KNO [I YES See Section 4.2.1.6 of the RM 7. Fire Protection Program (applicable UFSAR or operating license EgNO 0l YES See Section 4.2.1.7 of the RM condition)?
KNO [I YES See Section 4.2.1.6 of the RM7. Fire Protection Program (applicable UFSAR or operating license EgNO 0l YES See Section 4.2.1.7 of the RMcondition)?
: 8. Programs controlled by the Operating License or the Technical ANO [: YES See Section 4.2.1.7 of the RM Specifications (such as the ODCM).9. Environmental Protection Program [NO E] YES See Section 4.2.1.7 of the RM 10. Other programs controlled by other regulations.
: 8. Programs controlled by the Operating License or the Technical ANO [: YES See Section 4.2.1.7 of the RMSpecifications (such as the ODCM).9. Environmental Protection Program [NO E] YES See Section 4.2.1.7 of the RM10. Other programs controlled by other regulations.
toa.p.(, I ,l0 El NO K"YES See Section 4.2.1 of the RM II. Does the proposed Activity involve maintenance which restores SSCs to their original condition or involve a temporary alteration supporting D(NO maintenance that will be in effect during at-power operations for 90 days or less?Ill. Does the proposed Activity involve a change to the: I1. UFSAR (including documents incorporated by reference) that is limited to reformatting, simplification, removing excessive detail, or minor XNO Cl YES See Section 4.2.3 of the RM editorial changes as discussed in NEI 96-07 or NEI 98-03?2. Managerial or administrative procedures governing the conduct of [E NO rMYES See Section 4.2.4 of the RM facility operations (subject to the control of IOCFR50, Appendix B)3. Procedures for performing maintenance activities (subject to IOCFR50, [I"NO C1 YES See Section 4.2.4 of the RM Appendix B)?4. Regulatory commitment not covered by another regulation based change KNO 0l YES See Section 4.2.3/4.2.4 of the RM process (see NEI 99-04)?IV. Does the proposed Activity involve a change to the Independent Spent Fuel (NO El YES See Section 4.2.6 of the RM Storage Installation (ISFSI) (subject to control by 10 CFR 72.48)Check one of the following:
toa.p.(,
* If all asoects of the Activity are controlled by one or more of the above processes, then a 50.59 Screening is not required and the Activity may be implemented in accordance with its governing procedure.
I ,l0 El NO K"YES See Section 4.2.1 of the RMII. Does the proposed Activity involve maintenance which restores SSCs totheir original condition or involve a temporary alteration supporting D(NOmaintenance that will be in effect during at-power operations for 90 days orless?Ill. Does the proposed Activity involve a change to the:I1. UFSAR (including documents incorporated by reference) that is limitedto reformatting, simplification, removing excessive detail, or minor XNO Cl YES See Section 4.2.3 of the RMeditorial changes as discussed in NEI 96-07 or NEI 98-03?2. Managerial or administrative procedures governing the conduct of [E NO rMYES See Section 4.2.4 of the RMfacility operations (subject to the control of IOCFR50, Appendix B)3. Procedures for performing maintenance activities (subject to IOCFR50,  
El If any portion of the Activity is not controlled by one or more of the above processes, then process a 50.59 Screening for the portion not covered by any of the above processes.
[I"NO C1 YES See Section 4.2.4 of the RMAppendix B)?4. Regulatory commitment not covered by another regulation based change KNO 0l YES See Section 4.2.3/4.2.4 of the RMprocess (see NEI 99-04)?IV. Does the proposed Activity involve a change to the Independent Spent Fuel (NO El YES See Section 4.2.6 of the RMStorage Installation (ISFSI) (subject to control by 10 CFR 72.48)Check one of the following:
The remaining portion of the activity should be implemented in accordance with its governing procedure.
* If all asoects of the Activity are controlled by one or more of the above processes, then a 50.59 Screening is not required andthe Activity may be implemented in accordance with its governing procedure.
0.59 S _ Sign: I Date: (Circle One) (Print name) (Signature)
El If any portion of the Activity is not controlled by one or more of the above processes, then process a 50.59 Screening for theportion not covered by any of the above processes.
C 50.59 REVIEW COVERSHEET FORM LS-AA-104-1001 Revision 3 Page 1 of 1 Station/Unit(s):
The remaining portion of the activity should be implemented inaccordance with its governing procedure.
TMI -1 Activity/Document Number: RW-AA-100 Revision Number: 8 Title: Process Control Program for Radioactive Wastes NOTE: For 50.59 Evaluations, information on this form will provide the basis for preparing the biennial summary report submitted to the NRC in accordance with the requirements of 10 CFR 50.59(d)(2).
0.59 S _ Sign: I Date:(Circle One) (Print name) (Signature)
Description of Activity: (Provide a brief, concise description of what the proposed activity involves.)
C 50.59 REVIEW COVERSHEET FORM LS-AA-104-1001 Revision 3Page 1 of 1Station/Unit(s):
Issue rev 8 of corporate procedure RW-AA- 100, Process Control Program for Radioactive Wastes which describes the administrative program requirements for the Process Control Program (PRP).Rev 8 changes include:* (step 4.1.8) Allow an Exelon Nuclear plant to store radioactive waste from another Exelon Nuclear plant provided formal NRC approval is granted for the transfer of waste.0 (step 4.2.8) modify statement to include " in the pool or loading the processed activated hardware into Dry Case storage system."* (step 4.4.4) Add statement that Shipment sent off-site storage shall meet the storage site's waste acceptance criteria.* Minor editorial changes and grammatical error corrections to improve readability of the document.Reason for Activity: (Discuss why the proposed activity is being performed.)
TMI -1Activity/Document Number: RW-AA-100 Revision Number: 8Title: Process Control Program for Radioactive WastesNOTE: For 50.59 Evaluations, information on this form will provide the basis for preparing the biennial summary reportsubmitted to the NRC in accordance with the requirements of 10 CFR 50.59(d)(2).
RW-AA- 100 rev 8 steps 4.1.8 and 4.4.4 are added to address transfer and storage of radioactive waste from one Exelon Nuclear plant to another Exelon Nuclear plant provided formal NRC approval is granted. Step 4.2.8 is amended to further clarify the storage of activated hardware.Effect of Activity: (Discuss how the activity impacts plant operations, design bases, or safety analyses described in the UFSAR.)The activity is a change to an administrative procedure and has no impact on plant operations, design basis, or safety analysis described in the UFSAR.Summary of Conclusion for the Activity's 50.59 Review: (Provide justification for the conclusion, including sufficient detail to recognize and understand the essential arguments leading to the conclusion.
Description of Activity:
(Provide a brief, concise description of what the proposed activity involves.)
Issue rev 8 of corporate procedure RW-AA- 100, Process Control Program for Radioactive Wastes which describes theadministrative program requirements for the Process Control Program (PRP).Rev 8 changes include:* (step 4.1.8) Allow an Exelon Nuclear plant to store radioactive waste from another Exelon Nuclear plant providedformal NRC approval is granted for the transfer of waste.0 (step 4.2.8) modify statement to include " in the pool or loading the processed activated hardware into Dry Casestorage system."* (step 4.4.4) Add statement that Shipment sent off-site storage shall meet the storage site's waste acceptance criteria.
* Minor editorial changes and grammatical error corrections to improve readability of the document.
Reason for Activity:
(Discuss why the proposed activity is being performed.)
RW-AA- 100 rev 8 steps 4.1.8 and 4.4.4 are added to address transfer and storage of radioactive waste from one Exelon Nuclearplant to another Exelon Nuclear plant provided formal NRC approval is granted.
Step 4.2.8 is amended to further clarify thestorage of activated hardware.
Effect of Activity:
(Discuss how the activity impacts plant operations, design bases, or safety analyses described in the UFSAR.)The activity is a change to an administrative procedure and has no impact on plant operations, design basis, or safety analysisdescribed in the UFSAR.Summary of Conclusion for the Activity's 50.59 Review:(Provide justification for the conclusion, including sufficient detail to recognize and understand the essential arguments leadingto the conclusion.
Provide more than a simple statement that a 50.59 Screening, 50.59 Evaluation, or a License Amendment Request; as applicable, is not required.).  
Provide more than a simple statement that a 50.59 Screening, 50.59 Evaluation, or a License Amendment Request; as applicable, is not required.).  
.... .... ......The Process Control Program is a tech spec required program to ensure processed Radioactive Wastes meets applicable criteriafor disposal.
.... .... ......The Process Control Program is a tech spec required program to ensure processed Radioactive Wastes meets applicable criteria for disposal.
RW-AA-100 is an admihistrative procedure governing the conduct of facility operation and is not subject toIOCFR50.59 review in accordance with LS-AA-104-1000 section 4.2.4, Exelon 50.59 Resource Manual.Attachments:
RW-AA-100 is an admihistrative procedure governing the conduct of facility operation and is not subject to IOCFR50.59 review in accordance with LS-AA-104-1000 section 4.2.4, Exelon 50.59 Resource Manual.Attachments:
Attach all 50.59 Review forms completed, as appropriate.
Attach all 50.59 Review forms completed, as appropriate.
Forms Attached:  
Forms Attached: (Check all that apply.)0 Applicability Review E0 50.59 Screening 50.59 Screening No. Rev.EJ 50.59 Evaluation 50.59 Evaluation No. Rev.
(Check all that apply.)0 Applicability ReviewE0 50.59 Screening 50.59 Screening No. Rev.EJ 50.59 Evaluation 50.59 Evaluation No. Rev.
Fleet Standard Document -Corporate Approval Form AD-AA-101-F-09 Page 2 of 2 Revision 0 1. Step 4.1.8 suggested wording should read: "An Exelon Nuclear plant may store waste at another Exelon Nuclear plant, provided formal NRC approval has been received for the transfer of waste." 2. Add a step under section 4.4 "Shipment sent for off site storage shall meet the storage site's waste acceptance criteria 3. Add step 4.1.8 "It also possible to store waste from one nuclear plant at another nuclear plant, if formal NRC approval has been received." 4. Modify step 4.2.8 by adding the following words at the end of sentence "in the pool or loading the processed activated hardware into Dry Case storage system.
Fleet Standard Document  
Fleet Standard Document -Corporate Approval Form Page 1 of 2 AD-AA-101-F-09 Revision 0 See AD-AA- 101 for the procedural requirements associated with this Form.Desktop Instruction available on Intranet or through AD functional area.Document Number: RW-AA-100 Revision:
-Corporate Approval Form AD-AA-101-F-09 Page 2 of 2 Revision  
8 Title: Process Control Program for Radioactive Wastes Superseded Fleet Standard Documents:
: 01. Step 4.1.8 suggested wording should read: "An Exelon Nuclear plant may store wasteat another Exelon Nuclear plant, provided formal NRC approval has been received forthe transfer of waste."2. Add a step under section 4.4 "Shipment sent for off site storage shall meet the storagesite's waste acceptance criteria3. Add step 4.1.8 "It also possible to store waste from one nuclear plant at another nuclearplant, if formal NRC approval has been received."
NIA 0 or List: Batch -Are multiple document creations/revisions/cancelations being issued to add/revise/cancel them for similar reouirements?
: 4. Modify step 4.2.8 by adding the following words at the end of sentence "in the pool orloading the processed activated hardware into Dry Case storage system.
No M or Yes fl If Yes, then identify the hiohest level Document and Issue Type below.Check only one Document Tvoe: Check only one Issue Type: Incorporated Fleet Items: Level 1 -Continuous Use Procedure El New El Level 2 -Reference Use Procedure 0 Revision 0 Level 3 -Information Use Procedure 0 Editorial Revision 0 T&RM 0 Cancel Document [Form E] Cancel Revision __Revision Summary: See attached Summary of Changes.(Attach additional descdption iR rewuired)CONFIRM that no commitments (i.e., those steps annotated with CM-X) have been changed or deleted unless evaluated via completion of LS-AA-1 10 commitment change/deletion form and INITIAL [Preparer]:
Fleet Standard Document  
RMC Preparer Robert Class 03/07/12 canterwafs0372829 Print Date Location and EUt Site Applicability and Contacts -Check box and provide name: BRW 0 Michael Gorap DRE 0 Sandy Uvecchl OYS 0 Gonzalo Lamena TMI 0 Tamara Hanlon BYR 0 Norma Gordon LAS [ Lynn Kofold-Durden PEA 0 George Tharpe ZIN 0 CPS 0 Anthony KllbUm LIM 0 Unda Knapp QDC Debra Cline Other 0 Affected Functional Area (FA) -Check box & provide Corporate contact name if FA is affected by this revision: AD [I ER [] NO C_ RW [I AR [I_ HRO [ OP 0_ SA [I B1O [1 HUO _ OUO _ _SM []Cc [] IT _ _3. PC 0_ SY 0_CY []_ LR [-_ PI _ _ TO []El 0 LS 0_ PL [I WC 0_ENO MAO [ RM 0 -__EP []_ NF I" RP [] -__I___'Validation  
-Corporate Approval FormPage 1 of 2AD-AA-101-F-09 Revision 0See AD-AA- 101 for the procedural requirements associated with this Form.Desktop Instruction available on Intranet or through AD functional area.Document Number: RW-AA-100 Revision:
-Is substantiating this document's usability via mockup, simulated performance, field walkdown, or bench top review required?
8Title: Process Control Program for Radioactive WastesSuperseded Fleet Standard Documents:
NIA 0 or List:Batch -Are multiple document creations/revisions/cancelations being issued to add/revise/cancel them for similarreouirements?
No M or Yes fl If Yes, then identify the hiohest level Document and Issue Type below.Check only one Document Tvoe: Check only one Issue Type: Incorporated Fleet Items:Level 1 -Continuous Use Procedure El New ElLevel 2 -Reference Use Procedure 0 Revision 0Level 3 -Information Use Procedure 0 Editorial Revision 0T&RM 0 Cancel Document  
[Form E] Cancel Revision
__Revision Summary:
See attached Summary of Changes.(Attach additional descdption iR rewuired)
CONFIRM that no commitments (i.e., those steps annotated with CM-X) have been changed or deleted unlessevaluated via completion of LS-AA-1 10 commitment change/deletion form and INITIAL [Preparer]:
RMCPreparer Robert Class 03/07/12 canterwafs0372829 Print Date Location and EUtSite Applicability and Contacts  
-Check box and provide name:BRW 0 Michael Gorap DRE 0 Sandy Uvecchl OYS 0 Gonzalo Lamena TMI 0 Tamara HanlonBYR 0 Norma Gordon LAS [ Lynn Kofold-Durden PEA 0 George Tharpe ZIN 0CPS 0 Anthony KllbUm LIM 0 Unda Knapp QDC Debra Cline Other 0Affected Functional Area (FA) -Check box & provide Corporate contact name if FA is affected by this revision:
AD [I ER [] NO C_ RW [IAR [I_ HRO [ OP 0_ SA [IB1O [1 HUO _ OUO _ _SM []Cc [] IT _ _3. PC 0_ SY 0_CY []_ LR [-_ PI _ _ TO []El 0 LS 0_ PL [I WC 0_ENO MAO [ RM 0 -__EP []_ NF I" RP [] -__I___'Validation  
-Is substantiating this document's usability via mockup, simulated performance, field walkdown, orbench top review required?
No 0 or Yes [] ff Yes, then attach validation documentation.
No 0 or Yes [] ff Yes, then attach validation documentation.
If Yes, then print name & sign for completed validation:
If Yes, then print name & sign for completed validation:
4-NOS Review -Excluding NDE, ISI, Peer Inspection or Independent Verification, is this document used to performindependent inspection for acceptance (including field installation inspections, fabrication inspections, receiptinspections, new fuel inspection, etc.), or for certification of Inspection personnel?
4-NOS Review -Excluding NDE, ISI, Peer Inspection or Independent Verification, is this document used to perform independent inspection for acceptance (including field installation inspections, fabrication inspections, receipt inspections, new fuel inspection, etc.), or for certification of Inspection personnel?
No 0 or Yes C0If Yes, then NOS Reviewer to print name & sign for acceptance:
No 0 or Yes C0 If Yes, then NOS Reviewer to print name & sign for acceptance:
Common Training  
Common Training -Is common training material being provided? (Document in the change management how the common training material will be developed and pmvided to the sites or attach.) No 0 or Yes 01 Change Management provided in: HU-AA-)4'1 CPaWge Checklist Attached [I or: As directed by SFAM Z r CFAM Approval Miguel Azar/ /j .03/07/12 Cantera/3240 EPd -V Date Location and Ext SRRS Number 1B.100 Document Site Approval Form Page 2 of 2 AD-AA-101-F-O1 Revision 4 Continuation B -Is this a T&RM, or Form? NodS or Yes [] If yes, then skip the following section and go Continuation C.PORC R quired: If yes, then enter PORC Numr r (a er P Approved):
-Is common training material being provided?  
(Document in the change management how thecommon training material will be developed and pmvided to the sites or attach.)
No 0 or Yes 01Change Management provided in: HU-AA-)4'1 CPaWge Checklist Attached  
[I or: As directed by SFAM Zr CFAM Approval Miguel Azar/ /j .03/07/12 Cantera/3240 EPd -V Date Location and ExtSRRS Number 1B.100 Document Site Approval FormPage 2 of 2AD-AA-101-F-O1 Revision 4Continuation B -Is this a T&RM, or Form? NodS or Yes [] If yes, then skip the following section and goContinuation C.PORC R quired: If yes, then enter PORC Numr r (a er P Approved):
Plant Manager Print and Si (whn regu)e by procedure)
Plant Manager Print and Si (whn regu)e by procedure)
_ _,, b _,ateContinuation C -Is this an Editorial Revision;,No]%,or es If yes, then skip the following section and go toContinuation D.Applicable Site. Contact/Site Change Agents (SME): -1 C *-Responsible for Change Management information in---his form or E] HU-AA-1 101 Checklist (attached)
_ _,, b _,ate Continuation C -Is this an Editorial Revision;,No]%,or es If yes, then skip the following section and go to Continuation D.Applicable Site. Contact/Site Change Agents (SME): -1 C *-Responsible for Change Management information in---his form or E] HU-AA-1 101 Checklist (attached)
-Responsible to shepherd the document through site review, approval/authorization, and implementation.
-Responsible to shepherd the document through site review, approval/authorization, and implementation.
Affected Functional Area(s) or Individuals:
Affected Functional Area(s) or Individuals:-j) Pit ,, U Signature Date Af e FA Print Signature Date Affected FA Prnt Signature Date Affected FA Attach additional if recfd Resources needed to Implement Change: "At rOnly list, if other than Level of Effort.)For ongoing impacts, estimate number of Full Time Equivalents (FTE). If additional resources are needed go to HU-AA-1101.Communication Plan: (e.g., e-mail, Site Paper, Supervisor Briefing, Voice Mail, etc.)Training Required I Qualifications affected: El Yes If yes, list: (e.g., Supervisory Briefing, Tailgate Briefing, Required Reading, Formal Training, recertification etc.)Update to information infrastructure (e.g. PassPort, PIMS, EDMS w9flows, etc.) required to support implementation (including updated forms loaded into PassPort):
-j) Pit ,, U Signature Date Af e FAPrint Signature Date Affected FAPrnt Signature Date Affected FAAttach additional if recfdResources needed to Implement Change: "At rOnly list, if other than Level of Effort.)For ongoing impacts, estimate number of Full Time Equivalents (FTE). If additional resources are needed go to HU-AA-1101.Communication Plan: (e.g., e-mail, Site Paper, Supervisor  
AV Controlled Document distribution (ref. RM-AA-1 02) or Records Retention Schedule (ref. RM-AA-1 01-1004)impacted:  
: Briefing, Voice Mail, etc.)Training Required I Qualifications affected: El Yes If yes, list:(e.g., Supervisory  
: Briefing, Tailgate  
: Briefing, Required  
: Reading, Formal Training, recertification etc.)Update to information infrastructure (e.g. PassPort, PIMS, EDMS w9flows, etc.) required to supportimplementation (including updated forms loaded into PassPort):
AVControlled Document distribution (ref. RM-AA-1 02) or Records Retention Schedule (ref. RM-AA-1 01-1004)impacted:  
$No 0l Yes If yes, describe change and list Records Manager contacted:
$No 0l Yes If yes, describe change and list Records Manager contacted:
IContinuation D -If all procedurally required activities associated with this document revision have been completed and the document is ready for implementatio4, then SFAM to print name, sign & date for authorization to implement.
I Continuation D -If all procedurally required activities associated with this document revision have been completed and the document is ready for implementatio4, then SFAM to print name, sign & date for authorization to implement.
Provide implementation date or, if the Implementation Date is blank or N/A then implementation will be upon theissuance by Records Management per RM requirements.
Provide implementation date or, if the Implementation Date is blank or N/A then implementation will be upon the issuance by Records Management per RM requirements.
Authorization below indicates the SFAM or a designee ofthe SFAM has verified the document does not alter or negatively impact compliance with regulatory requirements orL#tOGln &#xfd;^mnlfmmnfa IInterim Chg # 01Authorization:
Authorization below indicates the SFAM or a designee of the SFAM has verified the document does not alter or negatively impact compliance with regulatory requirements or L#tOGln &#xfd;^mnlfmmnfa I Interim Chg # 01 Authorization:
A1/... /4L..L'Z_____
A1/... /4L..L'Z_____
i-PPrintaate Imi, Date Exp. DateSRRS Number 1 B.160 Document Site Approval Form Page 1 of 2AD-AA-1 01 -F-01Revision 4See AD-AA-101 for the procedural requirements associated with this Form.Desktop Instruction available on Intranet or through AD functional area. &#xfd; Facility:
i-PPrintaate Imi, Date Exp. Date SRRS Number 1 B.160 Document Site Approval Form Page 1 of 2 AD-AA-1 01 -F-01 Revision 4 See AD-AA-101 for the procedural requirements associated with this Form.Desktop Instruction available on Intranet or through AD functional area. &#xfd; Facility: DocumetNumber:
DocumetNumber:
P,),.) G (00 Revision:
P,),.) G (00 Revision:
WTitle: a-F-S, C a cr V .o XcA' ASuperseded Documents:
W Title: a-F-S, C a cr V .o XcA' A Superseded Documents:
N/AKor List: WE] Check this box if superseding a document containing commitments,  
N/AKor List: W E] Check this box if superseding a document containing commitments, 'notify the Commitment Trabking Coordinator per LS-AA-1 10 so the CTD can be updated as appropriate.
'notify the Commitment TrabkingCoordinator per LS-AA-1 10 so the CTD can be updated as appropriate.
Environmental Review Applicability  
Environmental Review Applicability  
-Is an Environmental Review ap5plicable per EN-AA-1 03? Noj or Yes E]If Yes, then attach Environmental Review documentation required per EN-AA-103.  
-Is an Environmental Review ap5plicable per EN-AA-1 03? Noj or Yes E]If Yes, then attach Environmental Review documentation required per EN-AA-103. , I Is this a Fleet Standard Document being pirocessed with form AD-AA-1O1-F-09?
, IIs this a Fleet Standard Document being pirocessed with form AD-AA-1O1-F-09?
No E] or Yes K If yes, then attach the completed form AD-AA- 10.-F-09, skip the following section, and go to Continuation A. 41 Qth -Are multiple document creations/revisionslcancelations being issued to add/revise/cancel them for similar redbizements?
No E] or Yes K If yes, thenattach the completed form AD-AA- 10.-F-09, skip the following  
No M- or Yes -- If Yes. then identify the hiahest level Document and Issue Tvne below Check oni e Document Type: Check only one Issue Type: Incorporated Site ItemsML, AR, Level 1 -Con i us Use Procedure El .New E] PCR, etc): ,&#xfd;n~ usRevision E Level 2 -Referenc se Procedure E]Cancel Document Level 3 -Information Us rocedure El Cancel Revision E]RM Non-Permanent El Fo Editorial Revision Revision Summary: &#xfd; 7 (Attach additional description if CONFIRM that no commitments (i.e., those steps CM-X) have been changed or deleted unless evaluated via completion of LS-AA-1 10 commitmenJ, eiange~deaietion form and INITIAL [Preparer]:
: section, and go to Continuation A. 41Qth -Are multiple document creations/revisionslcancelations being issued to add/revise/cancel them for similarredbizements?
No M- or Yes -- If Yes. then identify the hiahest level Document and Issue Tvne belowCheck oni e Document Type: Check only one Issue Type: Incorporated Site ItemsML, AR,Level 1 -Con i us Use Procedure El .New E] PCR, etc):,&#xfd;n~ usRevision ELevel 2 -Referenc se Procedure E]Cancel DocumentLevel 3 -Information Us rocedure El Cancel Revision E]RM Non-Permanent ElFo Editorial RevisionRevision Summary:  
&#xfd; 7(Attach additional description if CONFIRM that no commitments (i.e., those steps CM-X) have been changed or deleted unlessevaluated via completion of LS-AA-1 10 commitmenJ, eiange~deaietion form and INITIAL [Preparer]:
PreprerPrintJ Date Extension Validation  
PreprerPrintJ Date Extension Validation  
-Is substantiating this cument's usability via mockup, simulatedl*.  
-Is substantiating this cument's usability via mockup, simulatedl*.
: ormance, field walkdown, orbench top review required?
ormance, field walkdown, or bench top review required?
NeU or Yes n ] m f Yes, then attach validation documeen.
NeU or Yes n ] m f Yes, then attach validation documeen.If Yes, then print narneWgn for completed validation:
If Yes, then print narneWgn for completed validation:
NOS Review -_.&#xfd;.-'1ding NDE, ISI, Peer Inspection or Independent Verification, is this docurne'ht, sed to perform for acceptance (including field installation inspections, fabrication inspecJ~ts, new fuel inspection, etc.), or for certification of Inspection personnel?No E] or Yes Elthen NOS Reviewer to print name & sign for acceptance: Continuation A -Is this a T&RM, Form, or Editorial Revision?
NOS Review -_.&#xfd;.-'1ding NDE, ISI, Peer Inspection or Independent Verification, is this docurne'ht, sed to perform for acceptance (including field installation inspections, fabrication inspecJ~ts, new fuel inspection, etc.), or for certification of Inspection personnel?No E] or Yes Elthen NOS Reviewer to print name & sign for acceptance: Continuation A -Is this a T&RM, Form, or Editorial Revision?
No PS or Yes L] If yes, then skip the following section and go Continuation B.Impact on Operating and Design Margins -N/A~jor explain:(Attach additional description if required)
No PS or Yes L] If yes, then skip the following section and go Continuation B.Impact on Operating and Design Margins -N/A~jor explain: (Attach additional description if required)No [] Yes I0CFR50.59 Applicable?
No [] Yes I0CFR50.59 Applicable?
Tracking Number (/A,.KNo [] Yes 10CFR72.48 Applicable?
Tracking Number (/A,.KNo [] Yes 10CFR72.48 Applicable?
9No El Yes Other Regulatory Process Applicable?
9No El Yes Other Regulatory Process Applicable?
Other Regulatory Process Number: (/u/4[] Yes Potential security impact per SY-AA-500-127?
Other Regulatory Process Number: (/u/4[] Yes Potential security impact per SY-AA-500-127?
If Yes, then Security Reviewer acceptance documented bycross discipline review belowNo 0i Yes Surveillance Coordinator Review Required?
If Yes, then Security Reviewer acceptance documented by cross discipline review below No 0i Yes Surveillance Coordinator Review Required?
If Yes, then Surveillance Coordinator Review documented by cross discipline review belowCross Discipline Reviews:  
If Yes, then Surveillance Coordinator Review documented by cross discipline review below Cross Discipline Reviews: (list below)-z, f.4 ,vt., Print Print Print Signature Data(~I2 _i__ReO Date Discipline or Org.Date Discipline or Org.Date Discipline or Org.Signature Signature 1-l auu-nlll "T IQ U SQR Approval indicates that all required Cross-Disciplinary reviews have been performed and the reviewers have signed this form. This procedure is technically and functionally accurate f r all functional area /(See ADAA-102)SOR Approval:ad  
(list below)-z, f.4,vt.,PrintPrintPrintSignature Data(~I2
/0n --i 2a -Print end Sign Date Dsiln 2013 Annual Radioactive Effluent Release Report for TMI Enclosure 2 -Page 1 of 1 Process Control Program for Radioactive Wastes, Revision 8 RW-AA-100 (Revision 8 was issued on March 20, 2013) 1 RW-AA-1 00 e lamRevision 8 Ex l " Page 1 of 9 Nuclear Level 3 -Information Use PROCESS CONTROL PROGRAM FOR RADIOACTIVE WASTES 1. PURPOSE 1.1. The purpose of the Process Control Program (PCP) is to: 1.1.1. Establish the process and boundary conditions for the preparation of specific procedures for processing, sampling, analysis, packaging, storage, and shipment of solid radwaste in accordance with local, state, and federal requirements. (CM-1)1.1.2. Establish parameters which will provide reasonable assurance that all Low Level Radioactive Wastes (LLRW), processed by the in-plant waste process systems on-site OR by on-site vendor supplied waste processing systems, meet the acceptance criteria to a Licensed Burial Facility, as required by 10CFR Part 20, 1OCFR Part 61, 10CFR Part 71, 49CFR Parts 171-172, "Technical Position on Waste Form (Revision 1)" [1/91], "Low-Level Waste Licensing Branch Technical Position on Radioactive Waste Classification" [5/83], and the Station Technical Specifications, as applicable.
_i__ReODate Discipline or Org.Date Discipline or Org.Date Discipline or Org.Signature Signature 1-l auu-nlll "T IQ USQR Approval indicates that all required Cross-Disciplinary reviews have been performed and the reviewers have signed this form. Thisprocedure is technically and functionally accurate f r all functional area /(See ADAA-102)
1.1.3. Provide reasonable assurance that waste placed in "on-site storage" meets the requirements as addressed within the Safety Analysis Reports for the low level radwaste storage facilities for dry and/or processed wet waste.2. TERMS AND DEFINITIONS 2.1. Process Control Program (PCP): The program which contains the current formulas, sampling, analysis, tests, and determinations to be made to ensure that processing and packaging of solid radioactive waste based on demonstrated processing of actual or simulated wet solid wastes will be accomplished in such a way as to assure the waste meets the stabilization criteria specified in 10CFR Parts 20, 61 and 71, state regulations, and burial site requirements.
SOR Approval:ad  
/0n --i 2a -Print end Sign Date Dsiln 2013 Annual Radioactive Effluent Release Report for TMIEnclosure 2 -Page 1 of 1Process Control Program for Radioactive Wastes, Revision 8RW-AA-100 (Revision 8 was issued on March 20, 2013) 1RW-AA-1 00e lamRevision 8Ex l " Page 1 of 9Nuclear Level 3 -Information UsePROCESS CONTROL PROGRAM FOR RADIOACTIVE WASTES1. PURPOSE1.1. The purpose of the Process Control Program (PCP) is to:1.1.1. Establish the process and boundary conditions for the preparation of specificprocedures for processing,  
: sampling, analysis, packaging,  
: storage, and shipment ofsolid radwaste in accordance with local, state, and federal requirements.  
(CM-1)1.1.2. Establish parameters which will provide reasonable assurance that all Low LevelRadioactive Wastes (LLRW), processed by the in-plant waste process systemson-site OR by on-site vendor supplied waste processing  
: systems, meet theacceptance criteria to a Licensed Burial Facility, as required by 10CFR Part 20,1OCFR Part 61, 10CFR Part 71, 49CFR Parts 171-172, "Technical Position onWaste Form (Revision 1)" [1/91], "Low-Level Waste Licensing Branch Technical Position on Radioactive Waste Classification"  
[5/83], and the Station Technical Specifications, as applicable.
1.1.3. Provide reasonable assurance that waste placed in "on-site storage" meets therequirements as addressed within the Safety Analysis Reports for the low levelradwaste storage facilities for dry and/or processed wet waste.2. TERMS AND DEFINITIONS 2.1. Process Control Program (PCP): The program which contains the currentformulas,  
: sampling, analysis, tests, and determinations to be made to ensure thatprocessing and packaging of solid radioactive waste based on demonstrated processing of actual or simulated wet solid wastes will be accomplished in such away as to assure the waste meets the stabilization criteria specified in 10CFR Parts20, 61 and 71, state regulations, and burial site requirements.
2.2. Solidification:
2.2. Solidification:
Liquid waste processed to either an unstable or stable form per1OCFR61 requirements.
Liquid waste processed to either an unstable or stable form per 1OCFR61 requirements.
Waste solidified does not have to meet the 300-year freestanding monolith criteria.
Waste solidified does not have to meet the 300-year free standing monolith criteria.
Approved  
Approved formulas, samples and tests do not have to meet NRC approval for wastes solidified in a container meeting stability criteria (e.g.High Integrity Container).
: formulas, samples and tests do not have tomeet NRC approval for wastes solidified in a container meeting stability criteria (e.g.High Integrity Container).
2.3. Stabilization:
2.3. Stabilization:
Liquid waste processed to a "stable state" per 1OCFR61Requirements.
Liquid waste processed to a "stable state" per 1OCFR61 Requirements.
Established  
Established formulas, samples, and tests shall be approved by the NRC in order to meet solidification "stabilization" criteria.
: formulas, samples, and tests shall be approved by theNRC in order to meet solidification "stabilization" criteria.
This processing method is currently not available, because the NRC recognizes that waste packed in a High Integrity Container meets the 300-year stabilization criteria.
This processing method iscurrently not available, because the NRC recognizes that waste packed in a HighIntegrity Container meets the 300-year stabilization criteria.
In the event that this processing method becomes an acceptable method, then the NRC shall approve the stabilization formulas, samples, tests, etc.
In the event that thisprocessing method becomes an acceptable method, then the NRC shall approve thestabilization
I RW-AA-100 Revision 8 Page 2 of 9 2.4. Solidification Media: An approved media (e.g. Barnwell -vinyl ester styrene, cement, bitumen) when waste containing nuclides with greater than 5-year half lives is solidified in a container with activity greater than 1 micro curie/cc.
: formulas, samples, tests, etc.
Waste solidified in a HIC is approved by the commission meeting the 10CFR61 stabilization criteria, including 1% free standing liquids by volume when the waste is packaged to a"stable" form and < 0.5% when waste is packaged to an "unstable" form. The formulas, sampling, analysis, and test do not require NRC approval, because the HIC meets the stability criteria.2.4.1. Solidification to an unstable or stable state is performed by vendors, when applicable.
IRW-AA-100 Revision 8Page 2 of 92.4. Solidification Media: An approved media (e.g. Barnwell  
Liquid waste solidified to meet stabilization criteria (1OCFR61 and 01-91 Branch Technical Requirements) shall have documentation available that demonstrates that the process is approved by the NRC or disposal facility.2.5. Dewatering:
-vinyl ester styrene,cement, bitumen) when waste containing nuclides with greater than 5-year half livesis solidified in a container with activity greater than 1 micro curie/cc.
The process of removing fluids from liquid waste streams to produce a waste form that meets the requirements of 10CFR Part 61 and applicable burial site criteria, <0.5% by volume when the waste is packaged to an "unstable" state, or<1% by volume when the waste is packaged to a "stable" form.2.6. High Integrity Container (HIC): A disposable container that is approved to the Requirements of 10CFR61. The use of HIC's is an alternative to solidification or encapsulation in a steel container to meet burial stability.
Waste solidified in a HIC is approved by the commission meeting the 10CFR61 stabilization  
HIC's are used to package dewatered liquid wastes, (e.g. filter cartridges, filter media, resin, sludges, etc), or dry active waste.2.7. Encapsulation:
: criteria, including 1% free standing liquids by volume when the waste is packaged to a"stable" form and < 0.5% when waste is packaged to an "unstable" form. Theformulas,  
The process of placing a component (e.g. cartridge filters or mechanical components) into a special purpose disposable container and then completely surrounding the waste material with an approved stabilization media, such as cement.2.8. Liquid Waste Processing Systems: In-plant or vendor supplied processing systems consisting of equipment utilized for evaporation, filtration, demineralization, dewatering, compression dewatering, solidification, or reverse osmosis (RO) for the treatment of liquid wastes (such as Floor Drains, Chemical Drains and Equipment Drain inputs).2.9. Incineration, RVR, and/or Glass Vitrification of Liquid or Solid: Dry or wet waste processed via incineration and/or thermal processing where the volume is reduced by thermal means meets 1OCFR61 requirements.
: sampling, analysis, and test do not require NRC approval, because theHIC meets the stability criteria.
2.4.1. Solidification to an unstable or stable state is performed by vendors, whenapplicable.
Liquid waste solidified to meet stabilization criteria (1OCFR61 and 01-91Branch Technical Requirements) shall have documentation available thatdemonstrates that the process is approved by the NRC or disposal facility.
2.5. Dewatering:
The process of removing fluids from liquid waste streams to produce awaste form that meets the requirements of 10CFR Part 61 and applicable burial sitecriteria,  
<0.5% by volume when the waste is packaged to an "unstable" state, or<1% by volume when the waste is packaged to a "stable" form.2.6. High Integrity Container (HIC): A disposable container that is approved to theRequirements of 10CFR61.
The use of HIC's is an alternative to solidification orencapsulation in a steel container to meet burial stability.
HIC's are used to packagedewatered liquid wastes, (e.g. filter cartridges, filter media, resin, sludges, etc), ordry active waste.2.7. Encapsulation:
The process of placing a component (e.g. cartridge filters ormechanical components) into a special purpose disposable container and thencompletely surrounding the waste material with an approved stabilization media,such as cement.2.8. Liquid Waste Processing Systems:
In-plant or vendor supplied processing systems consisting of equipment utilized for evaporation, filtration, demineralization, dewatering, compression dewatering, solidification, or reverse osmosis (RO) for thetreatment of liquid wastes (such as Floor Drains, Chemical Drains and Equipment Drain inputs).2.9. Incineration, RVR, and/or Glass Vitrification of Liquid or Solid: Dry or wetwaste processed via incineration and/or thermal processing where the volume isreduced by thermal means meets 1OCFR61 requirements.
2.10. Compaction:
2.10. Compaction:
When dry wastes such as paper, wood, plastic, cardboard, incinerator ash, and etc. are volume reduced through the use of a compactor.
When dry wastes such as paper, wood, plastic, cardboard, incinerator ash, and etc. are volume reduced through the use of a compactor.
2.11. Waste Streams:
2.11. Waste Streams: Consist of but are not limited to-Filter media (powdered, bead resin and fiber),-Filter cartridges,-Pre-coat body feed material,-Contaminated  
Consist of but are not limited to-Filter media (powdered, bead resin and fiber),-Filter cartridges,
: charcoal, RW-AA-100 Revision 8 Page 3 of 9-Fuel pool activated hardware,-Oil Dry absorbent material added to a container to absorb liquids-Fuel Pool Crud-Sump and tank sludges,-High activity filter cartridges,-Concentrated liquids,-Contaminated waste oil,-Dried sewage or wastewater plant waste,-Dry Active Waste (DAW): Waste such as filters, air filters, low activity cartridge filters, paper, wood, glass, plastic, cardboard, hoses, cloth, and metals, etc, which have become contaminated as a consequence of normal operating, housekeeping and maintenance activities.
-Pre-coat body feed material,
-Contaminated  
: charcoal, RW-AA-100 Revision 8Page 3 of 9-Fuel pool activated  
: hardware,
-Oil Dry absorbent material added to a container to absorb liquids-Fuel Pool Crud-Sump and tank sludges,-High activity filter cartridges,
-Concentrated liquids,-Contaminated waste oil,-Dried sewage or wastewater plant waste,-Dry Active Waste (DAW): Waste such as filters, air filters, low activitycartridge
: filters, paper, wood, glass, plastic, cardboard, hoses, cloth, andmetals, etc, which have become contaminated as a consequence of normaloperating, housekeeping and maintenance activities.
Other radioactive waste generated from cleanup of inadvertent contamination.
Other radioactive waste generated from cleanup of inadvertent contamination.
: 3. RESPONSIBILITIES 3.1. Implementation of this Process Control Program (PCP) is described in procedures ateach station and is the responsibility of the each site to implement.
: 3. RESPONSIBILITIES 3.1. Implementation of this Process Control Program (PCP) is described in procedures at each station and is the responsibility of the each site to implement.
: 4. MAIN BODY4.1. Process Control Proqram Requirements 4.1.1. A change to this PCP (Radioactive Waste Treatment Systems) may be madeprovided that the change is reported as part of the annual radioactive effluentrelease report, Regulatory Guide 1.21, and is approved by the Plant Operations Review Committee (PORC).4.1.2. Changes become effective upon acceptance per station requirements.
: 4. MAIN BODY 4.1. Process Control Proqram Requirements 4.1.1. A change to this PCP (Radioactive Waste Treatment Systems) may be made provided that the change is reported as part of the annual radioactive effluent release report, Regulatory Guide 1.21, and is approved by the Plant Operations Review Committee (PORC).4.1.2. Changes become effective upon acceptance per station requirements.
4.1.3. A solidification media, approved by the burial site, may be REQUIRED when liquidradwaste is solidified to a stable/unstable state.4.1.4. When processing liquid radwaste to meet solidification stability using a vendorsupplied solidification system:1. If the vendor has its own Quality Assurance (QA) Program, then the vendorshall ADHERE to its own QA Program and shall have SUBMITTED itsprocess system topical report to the NRC or agreement state.2. If the vendor does not HAVE its own Quality Assurance  
4.1.3. A solidification media, approved by the burial site, may be REQUIRED when liquid radwaste is solidified to a stable/unstable state.4.1.4. When processing liquid radwaste to meet solidification stability using a vendor supplied solidification system: 1. If the vendor has its own Quality Assurance (QA) Program, then the vendor shall ADHERE to its own QA Program and shall have SUBMITTED its process system topical report to the NRC or agreement state.2. If the vendor does not HAVE its own Quality Assurance Program, then the vendor shall ADHERE to an approved Quality Assurance Topical Report standard belonging to the Station or to another approved vendor.
: Program, then thevendor shall ADHERE to an approved Quality Assurance Topical Reportstandard belonging to the Station or to another approved vendor.
RW-AA-100 Revision 8 Page 4 of 9 4.1.5. The vendor processing system(s) is/are controlled per the following:
RW-AA-100 Revision 8Page 4 of 94.1.5. The vendor processing system(s) is/are controlled per the following:
: 1. A commercial vendor supplied processing system(s) may be USED for the processing of LLRW streams.2. Vendors that process liquid LLRW at the sites shall MEET applicable Quality Assurance Topical Report and Augmented Quality Requirements.
: 1. A commercial vendor supplied processing system(s) may be USED for theprocessing of LLRW streams.2. Vendors that process liquid LLRW at the sites shall MEET applicable QualityAssurance Topical Report and Augmented Quality Requirements.
4.1.6. Vendor processing system(s) operated at the site shall be OPERATED and CONTROLLED in accordance with vendor approved procedures or station procedures based upon vendor approved documents.
4.1.6. Vendor processing system(s) operated at the site shall be OPERATED andCONTROLLED in accordance with vendor approved procedures or stationprocedures based upon vendor approved documents.
4.1.7. All waste streams processed for burial or long term on-site storage shall MEET the waste classification and characteristics specified in 1 OCFR Part 61.55, Part 61.56, the 5-83 Branch Technical Position for waste classification, and the applicable burial site acceptance criteria (for any burial site operating at the time the waste was processed).
4.1.7. All waste streams processed for burial or long term on-site storage shall MEET thewaste classification and characteristics specified in 1 OCFR Part 61.55, Part 61.56,the 5-83 Branch Technical Position for waste classification, and the applicable burialsite acceptance criteria (for any burial site operating at the time the waste wasprocessed).
4.1.8. An Exelon Nuclear plant may store waste at another Exelon Nuclear plant, provided formal NRC approval has been RECEIVED for the transfer of waste.4.2. General Waste Processing Requirements NOTE: On-site resin processing involves tank mixing and settling, transferring to the station or vendor processing system via resin water slurry or vacuuming into approved waste containers, and, when applicable, dewatering for burial.4.2.1. Vendor resin beds may be USED for decontamination of plant systems, such as, SFP (Spent Fuel Pool), RWCU (reactor water cleanup), and SDC (Shut Down Cooling).
4.1.8. An Exelon Nuclear plant may store waste at another Exelon Nuclear plant, providedformal NRC approval has been RECEIVED for the transfer of waste.4.2. General Waste Processing Requirements NOTE: On-site resin processing involves tank mixing and settling, transferring to the station or vendor processing system via resinwater slurry or vacuuming into approved waste containers, and,when applicable, dewatering for burial.4.2.1. Vendor resin beds may be USED for decontamination of plant systems, such as,SFP (Spent Fuel Pool), RWCU (reactor water cleanup),
These resins are then PROCESSED via the station or vendor processing system.4.2.2. Various drains and sump discharges will be COLLECTED in tanks or suitable containers for processing treatment.
and SDC (Shut DownCooling).
Water from these tanks may be SENT through a filter, demineralizer, concentrator or vendor supplied processing systems.4.2.3. Process waste (e.g. filter media, sludges, resin, etc) will be periodically DISCHARGED to the station or vendor processing system for onsite waste treatment or PACKAGED in containers for shipment to offsite vendor for volume reduction processing.
These resins are then PROCESSED via the station or vendor processing system.4.2.2. Various drains and sump discharges will be COLLECTED in tanks or suitablecontainers for processing treatment.
4.2.4. Process water (e.g. chemical, floor drain, equipment drain, etc.) may be SENT to either the site waste processing systems or vendor waste processing systems for further filtration, demineralization for plant re-use, or discharge.
Water from these tanks may be SENT througha filter, demineralizer, concentrator or vendor supplied processing systems.4.2.3. Process waste (e.g. filter media, sludges, resin, etc) will be periodically DISCHARGED to the station or vendor processing system for onsite wastetreatment or PACKAGED in containers for shipment to offsite vendor for volumereduction processing.
4.2.5. All dewatering and solidification/stabilization will be PERFORMED by either utility site personnel or by on-site vendors or will be PACKAGED and SHIPPED to an off-site vendor low-level radwaste processing facility.
4.2.4. Process water (e.g. chemical, floor drain, equipment drain, etc.) may be SENT toeither the site waste processing systems or vendor waste processing systems forfurther filtration, demineralization for plant re-use, or discharge.
RW-AA-100 Revision 8 Page 5 of 9 4.2.6. Dry Active Waste (DAW) will be HANDLED and PROCESSED per the following:
4.2.5. All dewatering and solidification/stabilization will be PERFORMED by either utilitysite personnel or by on-site vendors or will be PACKAGED and SHIPPED to anoff-site vendor low-level radwaste processing facility.
: 1. DAW will be COLLECTED and SURVEYED and may be SORTED for compactable and non-compactable wastes.2. DAW may be packaged in containers to facilitate on-site pre-compaction and/or off-site vendor contract requirements.
RW-AA-100 Revision 8Page 5 of 94.2.6. Dry Active Waste (DAW) will be HANDLED and PROCESSED per the following:
: 1. DAW will be COLLECTED and SURVEYED and may be SORTED forcompactable and non-compactable wastes.2. DAW may be packaged in containers to facilitate on-site pre-compaction and/or off-site vendor contract requirements.
: 3. DAW items may be SURVEYED for release onsite or offsite when applicable.
: 3. DAW items may be SURVEYED for release onsite or offsite when applicable.
: 4. Contaminated filter cartridges will be PLACED into a HIC or will beENCAPSULATED in an in-situ liner for disposal or SHIPPED to an offsitewaste processor in drums, boxes or steel liners per the vendor site criteria forprocessing and disposal.
: 4. Contaminated filter cartridges will be PLACED into a HIC or will be ENCAPSULATED in an in-situ liner for disposal or SHIPPED to an offsite waste processor in drums, boxes or steel liners per the vendor site criteria for processing and disposal.4.2.7. Filtering devices using pre-coat media may be USED for the removal of suspended solids from liquid waste streams. The pre-coat material or cartridges from these devices may be routinely REMOVED from the filter vessel and discharged to a Filter Sludge Tank or Liner/HIC.
4.2.7. Filtering devices using pre-coat media may be USED for the removal of suspended solids from liquid waste streams.
Periodically, the filter sludge may be DISCHARGED to the vendor processing system for waste treatment onsite or PACKAGED in containers for shipment to offsite vendor for volume reduction processing.
The pre-coat material or cartridges from thesedevices may be routinely REMOVED from the filter vessel and discharged to a FilterSludge Tank or Liner/HIC.
4.2.8. Activated hardware stored in the Spent Fuel Pools will be PROCESSED periodically using remote handling equipment and may then be PUT into a container for shipment or storage in the pool or loading the processed activated hardware into the Dry Cask storage system.4.2.9. High Integrity Containers (HIC): 1. For disposal at Barnwell, vendors supplying HIC's to the station shall PROVIDE a copy of the HIC Certificate of Compliance, which details specific limitations on use of the HIC.2. For disposal at Clive, vendors supplying HIC's to the station shall PROVIDE a copy of the HIC Certificate of Conformance, which details specific limitations on use of the HIC.3. Vendors supplying HIC's to the station shall PROVIDE a handling procedure which establishes guidelines for the utilization of the HIC. These guidelines serve to protect the integrity of the HIC and ensure the HIC is handled in accordance with the requirements of the Certificate of Compliance or Certificate of Conformance.
Periodically, the filter sludge may be DISCHARGED tothe vendor processing system for waste treatment onsite or PACKAGED incontainers for shipment to offsite vendor for volume reduction processing.
4.2.10. Lubricants and oils contaminated as a consequence of normal operating and maintenance activities may be PROCESSED on-site (by incineration, for oils meeting 10CFR20.2004 and applicable state requirements, or by an approved vendor process)or SHIPPED offsite (for incineration or other acceptable processing method).4.2.11. Former in-plant systems GE or Stock Drum Transfer Cart and Drum Storage Areas may be USED for higher dose DAW storage at Clinton, Dresden, Quad Cities, Braidwood and Byron.
4.2.8. Activated hardware stored in the Spent Fuel Pools will be PROCESSED periodically using remote handling equipment and may then be PUT into a container forshipment or storage in the pool or loading the processed activated hardware into theDry Cask storage system.4.2.9. High Integrity Containers (HIC):1. For disposal at Barnwell, vendors supplying HIC's to the station shallPROVIDE a copy of the HIC Certificate of Compliance, which details specificlimitations on use of the HIC.2. For disposal at Clive, vendors supplying HIC's to the station shall PROVIDE acopy of the HIC Certificate of Conformance, which details specific limitations on use of the HIC.3. Vendors supplying HIC's to the station shall PROVIDE a handling procedure which establishes guidelines for the utilization of the HIC. These guidelines serve to protect the integrity of the HIC and ensure the HIC is handled inaccordance with the requirements of the Certificate of Compliance orCertificate of Conformance.
F RW-AA-100 Revision 8 Page 6 of 9 4.2.13 Certain waste, including flowable solids from holding pond, oily waste separator, cooling tower basin and emergency spray pond, may be disposed of onsite under the provisions of a 10CFR20.2002 permit. Specific requirements associated with the disposal shall be incorporated into station implementing procedures. (CM-2)4.3. Burial Site Requirements 4.3.1. Waste sent directly to burial shall COMPLY with the applicable parts of 49CFR171-172, 10CFR61, 10CFR71, and the acceptance criteria for the applicable burial site.4.4. Shippingq and Inspection Requirements 4.4.1. All shipping/storage containers shall be INSPECTED, as required by station procedures, for compliance with applicable requirements (Department of Transportation (DOT), Nuclear Regulatory Commission (NRC), station, on-site storage, and/or burial site requirements) prior to use.4.4.2. Containers of solidified liquid waste shall be INSPECTED for solidification quality and/or dewatering requirements per the burial site, offsite vendor acceptance, or station acceptance criteria, as applicable.
4.2.10. Lubricants and oils contaminated as a consequence of normal operating andmaintenance activities may be PROCESSED on-site (by incineration, for oils meeting10CFR20.2004 and applicable state requirements, or by an approved vendor process)or SHIPPED offsite (for incineration or other acceptable processing method).4.2.11. Former in-plant systems GE or Stock Drum Transfer Cart and Drum Storage Areasmay be USED for higher dose DAW storage at Clinton,  
4.4.3. Shipments sent to an off site processor shall be INSPECTED to ensure that the applicable processor's waste acceptance criteria are being met.4.4.4. Shipments sent for off site storage shall MEET the storage site's waste acceptance criteria.4.5. Inspection and Corrective Action 4.5.1. Inspection results that indicate non-compliance with applicable NRC, State, vendor, or site requirements shall be IDENTIFIED and TRACKED through the Corrective Action Program.4.5.2. Administrative controls for preventing unsatisfactory waste forms from being released for shipment are described in applicable station procedures.
: Dresden, Quad Cities,Braidwood and Byron.
If the provisions of the Process Control Program are not satisfied, then SUSPEND shipments of defectively packaged radioactive waste from the site. (CM-1)4.5.3. If freestanding water or solidification not meeting program requirements is observed, then samples of the particular series of batches shall be TAKEN to determine the cause. Additional samples shall be TAKEN, as warranted, to ensure that no freestanding water is present and solidification requirements are maintained.
FRW-AA-100 Revision 8Page 6 of 94.2.13 Certain waste, including flowable solids from holding pond, oily waste separator, cooling tower basin and emergency spray pond, may be disposed of onsite underthe provisions of a 10CFR20.2002 permit. Specific requirements associated with thedisposal shall be incorporated into station implementing procedures.  
4.6. Procedure and Process Reviews 4.6.1. The Exelon Nuclear Process Control Program and subsequent changes (other than editorial/minor changes) shall be REVIEWED and APPROVED in accordance with the station procedures, plant-specific Technical Specifications (Tech Spec), Technical Requirements Manual (T&RM), Operation Requirements Manual (ORM), as applicable, for the respective station and LS-AA-106.
(CM-2)4.3. Burial Site Requirements 4.3.1. Waste sent directly to burial shall COMPLY with the applicable parts of49CFR171-172,  
Changes to the Licensees Controlled Documents, UFSAR, ORM, or TRM are controlled by the provisions of 10CFR 50.59.
: 10CFR61, 10CFR71, and the acceptance criteria for the applicable burial site.4.4. Shippingq and Inspection Requirements 4.4.1. All shipping/storage containers shall be INSPECTED, as required by stationprocedures, for compliance with applicable requirements (Department ofTransportation (DOT), Nuclear Regulatory Commission (NRC), station, on-sitestorage, and/or burial site requirements) prior to use.4.4.2. Containers of solidified liquid waste shall be INSPECTED for solidification qualityand/or dewatering requirements per the burial site, offsite vendor acceptance, orstation acceptance  
RW-AA-100 Revision 8 Page 7 of 9 4.6.2. Any changes to the PCP shall be reviewed to determine if reportability is required in the Annual Radiological Effluent Release Report (ARERR). The Radwaste Specialist shall ensure correct information is SUBMITTED to the ODCM program owner prior to submittal of the ARERR.4.6.3. Station processes, applicable site-specific cask manual procedures, or other vendor waste processing/operating procedures shall be approved per RM-AA-1 02-1006.Procedures related to waste manifests, shipment inspections, and container activity determinations are CONTROLLED by Radiation Protection Standard Procedures (RP-AA-600 Series).1. Site waste processing IS CONTROLLED by site operating procedures.
: criteria, as applicable.
4.4.3. Shipments sent to an off site processor shall be INSPECTED to ensure that theapplicable processor's waste acceptance criteria are being met.4.4.4. Shipments sent for off site storage shall MEET the storage site's waste acceptance criteria.
4.5. Inspection and Corrective Action4.5.1. Inspection results that indicate non-compliance with applicable NRC, State, vendor,or site requirements shall be IDENTIFIED and TRACKED through the Corrective Action Program.4.5.2. Administrative controls for preventing unsatisfactory waste forms from beingreleased for shipment are described in applicable station procedures.
If theprovisions of the Process Control Program are not satisfied, then SUSPENDshipments of defectively packaged radioactive waste from the site. (CM-1)4.5.3. If freestanding water or solidification not meeting program requirements is observed, then samples of the particular series of batches shall be TAKEN to determine thecause. Additional samples shall be TAKEN, as warranted, to ensure that nofreestanding water is present and solidification requirements are maintained.
4.6. Procedure and Process Reviews4.6.1. The Exelon Nuclear Process Control Program and subsequent changes (other thaneditorial/minor changes) shall be REVIEWED and APPROVED in accordance withthe station procedures, plant-specific Technical Specifications (Tech Spec),Technical Requirements Manual (T&RM), Operation Requirements Manual (ORM),as applicable, for the respective station and LS-AA-106.
Changes to the Licensees Controlled Documents, UFSAR, ORM, or TRM are controlled by the provisions of10CFR 50.59.
RW-AA-100 Revision 8Page 7 of 94.6.2. Any changes to the PCP shall be reviewed to determine if reportability is required inthe Annual Radiological Effluent Release Report (ARERR).
The RadwasteSpecialist shall ensure correct information is SUBMITTED to the ODCM programowner prior to submittal of the ARERR.4.6.3. Station processes, applicable site-specific cask manual procedures, or other vendorwaste processing/operating procedures shall be approved per RM-AA-1 02-1006.Procedures related to waste manifests, shipment inspections, and container activitydeterminations are CONTROLLED by Radiation Protection Standard Procedures (RP-AA-600 Series).1. Site waste processing IS CONTROLLED by site operating procedures.
: 2. Liquid processed by vendor equipment shall be PERFORMED in accordance with vendor procedures.
: 2. Liquid processed by vendor equipment shall be PERFORMED in accordance with vendor procedures.
4.7. Waste Types, Point of Generation, and Processing MethodMethods of processing and individual vendors may CHANGE due to changingfinancial and regulatory options.
4.7. Waste Types, Point of Generation, and Processing Method Methods of processing and individual vendors may CHANGE due to changing financial and regulatory options. The table below is a representative sample. It is not intended be all encompassing.
The table below is a representative sample. It isnot intended be all encompassing.
AVAILABLE WASTE WASTE STREAM POINTS OF GENERATION POEING M E PROCESSING METHODS Bead Resin Systems -Fuel Pool, Condensate, Dewatering, solidification to an Reactor Water Cleanup, Blowdown, unstable/stable state Equipment Drain, Chemical and Thermal Processing Volume Control Systems, Floor Drain, Maximum Recycle, Blowdown, Boric Free Release to a Land Fill Acid Recycling System, Vendor Supplied Processing Systems, and Portable Demin System Powdered Resin Systems -(Condensate System, Floor Dewatering, solidification to an Drain/Equipment Drain filtration, Fuel unstable/stable state Pool) Thermal Processing Concentrated Waste Waste generated from Site Solidification to an unstable/stable Evaporators resulting typically from the state Floor Drain and Equipment Drain Thermal Processing Systems ThermalProcessing Sludge Sedimentation resulting from various Dewatering, solidification to an sumps, condensers, tanks, cooling unstable/stable state tower, emergency spray pond, holding Thermal Processing pond, and oily waste separators Evaporation on-site or at an offsite processor On-site disposal per 10CFR20.2002 I permit RW-AA-100 Revision 8 Page 8 of 9 AVAILABLE WASTE WASTE STREAM POINTS OF GENERATION POEING ME PROCESSING METHODS Filter cartridges Systems -Floor/Equipment Drains, Dewatering, solidification to an Fuel Pool; cartridge filters are-typically unstable/stable state generated from clean up activities Processed by a vendor for volume within the fuel pool, torus, etc reduction Dry Active Waste Paper, wood, plastic, rubber, glass, Decon/Sorting for Free Release metal, and etc. resulting from daily Compaction/Super-compaction plant activities Thermal Processing by Incineration or glass vitrification Sorting for Free Release Metal melting to an ingot Contaminated Oil Oil contaminated with radioactive Solidification unstable state materials from any in-plant system. Thermal Processing by Incineration Free Release for recycling Drying Bed Sludge Sewage Treatment and Waste Water Free release to a landfill or burial Treatment Facilities Metals See DAW See DAW Irradiated Hardware Fuel Pool, Reactor Components Volume Reduction for packaging efficiencies
AVAILABLE WASTEWASTE STREAM POINTS OF GENERATION POEING M EPROCESSING METHODSBead Resin Systems -Fuel Pool, Condensate, Dewatering, solidification to anReactor Water Cleanup,  
: 5. DOCUMENTATION 5.1.1. Records of reviews performed shall be retained for the duration of the unit operating license. This documentation shall contain: 1. Sufficient information to support the change together with the appropriate analyses or evaluations justifying the change, and 2. A determination which documents that the change will maintain the overall conformance of waste products to Federal (10CFR61 and the Branch Technical Position), State, or other applicable requirements, including applicable burial site criteria.6.6.1.REFERENCES Technical Specifications:
: Blowdown, unstable/stable stateEquipment Drain, Chemical and Thermal Processing Volume Control Systems, Floor Drain,Maximum Recycle,  
6.1.1. The details contained in Current Tech Specs (CTS) or Improved Technical Specifications (ITS), as applicable, in regard to the Process Control Program (PCP), are to be relocated to the Licensee Controlled Documents.
: Blowdown, Boric Free Release to a Land FillAcid Recycling System, VendorSupplied Processing  
Some facilities have elected to relocate these details into the Operational Requirements Manual (ORM).Relocation of the description of the PCP from the CTS or ITS does not affect the safe operation of the facility.
: Systems, andPortable Demin SystemPowdered Resin Systems -(Condensate System, Floor Dewatering, solidification to anDrain/Equipment Drain filtration, Fuel unstable/stable statePool) Thermal Processing Concentrated Waste Waste generated from Site Solidification to an unstable/stable Evaporators resulting typically from the stateFloor Drain and Equipment Drain Thermal Processing Systems ThermalProcessing Sludge Sedimentation resulting from various Dewatering, solidification to ansumps, condensers, tanks, cooling unstable/stable statetower, emergency spray pond, holding Thermal Processing pond, and oily waste separators Evaporation on-site or at an offsiteprocessor On-site disposal per 10CFR20.2002 I permit RW-AA-100 Revision 8Page 8 of 9AVAILABLE WASTEWASTE STREAM POINTS OF GENERATION POEING MEPROCESSING METHODSFilter cartridges Systems -Floor/Equipment Drains, Dewatering, solidification to anFuel Pool; cartridge filters are-typically unstable/stable stategenerated from clean up activities Processed by a vendor for volumewithin the fuel pool, torus, etc reduction Dry Active Waste Paper, wood, plastic, rubber, glass, Decon/Sorting for Free Releasemetal, and etc. resulting from daily Compaction/Super-compaction plant activities Thermal Processing by Incineration or glass vitrification Sorting for Free ReleaseMetal melting to an ingotContaminated Oil Oil contaminated with radioactive Solidification unstable statematerials from any in-plant system. Thermal Processing by Incineration Free Release for recycling Drying Bed Sludge Sewage Treatment and Waste Water Free release to a landfill or burialTreatment Facilities Metals See DAW See DAWIrradiated Hardware Fuel Pool, Reactor Components Volume Reduction for packaging efficiencies
Therefore, the relocation details are not required to be in the CTS or the ITS to provide adequate protection of the public health and safety.
: 5. DOCUMENTATION 5.1.1. Records of reviews performed shall be retained for the duration of the unit operating license.
RW-AA-100 Revision 8 Page 9 of 9 6.2. Writers'  
This documentation shall contain:1. Sufficient information to support the change together with the appropriate analyses or evaluations justifying the change, and2. A determination which documents that the change will maintain the overallconformance of waste products to Federal (10CFR61 and the BranchTechnical Position),
State, or other applicable requirements, including applicable burial site criteria.
6.6.1.REFERENCES Technical Specifications:
6.1.1. The details contained in Current Tech Specs (CTS) or Improved Technical Specifications (ITS), as applicable, in regard to the Process Control Program (PCP),are to be relocated to the Licensee Controlled Documents.
Some facilities haveelected to relocate these details into the Operational Requirements Manual (ORM).Relocation of the description of the PCP from the CTS or ITS does not affect thesafe operation of the facility.
Therefore, the relocation details are not required to bein the CTS or the ITS to provide adequate protection of the public health and safety.
RW-AA-100 Revision 8Page 9 of 96.2. Writers'  


==References:==
==References:==


6.2.1. Code of Federal Regulations:
6.2.1. Code of Federal Regulations:
10 CFR Part 20, Part 61, Part 71, 49 CFRParts 171-1726.2.2. Low Level Waste Licensing Branch Technical Position on Radioactive WasteClassification, May 19836.2.3. Technical Position on Waste Form (Revision 1), January 19916.2.4. Branch Technical Position on Concentration Averaging and Encapsulation, January 19956.2.5. Regulatory Guide 1.21, Measuring Evaluating, and Reporting Radioactivity in SolidWastes and Releases of Radioactive materials in Liquid and Gaseous Effluents fromLight-Water-Cooled Nuclear Power Plants6.2.6. I.E. Circular 80.18, 1OCFR 50.59 Safety Evaluation for Changes to Radioactive Waste Treatment Systems6.3. Users'  
10 CFR Part 20, Part 61, Part 71, 49 CFR Parts 171-172 6.2.2. Low Level Waste Licensing Branch Technical Position on Radioactive Waste Classification, May 1983 6.2.3. Technical Position on Waste Form (Revision 1), January 1991 6.2.4. Branch Technical Position on Concentration Averaging and Encapsulation, January 1995 6.2.5. Regulatory Guide 1.21, Measuring Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive materials in Liquid and Gaseous Effluents from Light-Water-Cooled Nuclear Power Plants 6.2.6. I.E. Circular 80.18, 1OCFR 50.59 Safety Evaluation for Changes to Radioactive Waste Treatment Systems 6.3. Users'  


==References:==
==References:==


6.3.1. Quality Assurance Program (QATR)6.3.2. LS-AA-106, Plant Operations Review Committee 6.3.3. RM-AA-102-1006, Processing Vendor Documents 6.3.4. RP-AA-600 Series, Radioactive Material/Waste Shipments 6.3.5. CY-AA-170-2000, Annual Radioactive Effluent Release Report6.4. Station Commitments:
6.3.1. Quality Assurance Program (QATR)6.3.2. LS-AA-106, Plant Operations Review Committee 6.3.3. RM-AA-102-1006, Processing Vendor Documents 6.3.4. RP-AA-600 Series, Radioactive Material/Waste Shipments 6.3.5. CY-AA-170-2000, Annual Radioactive Effluent Release Report 6.4. Station Commitments:
6.4.1. Peach BottomCM-1, T03819, Letter from G.A. Hunger, Jr., dated Sept. 29 1994, transmitting TSCR 93-16 (Improved Technical Specifications).
6.4.1. Peach Bottom CM-1, T03819, Letter from G.A. Hunger, Jr., dated Sept. 29 1994, transmitting TSCR 93-16 (Improved Technical Specifications).
6.4.2. LimerickCM-2, T03896, 1OCFR20.2002 permit granted to Limerick via letter datedJuly 10, 1996.7. ATTACHMENTS  
6.4.2. Limerick CM-2, T03896, 1OCFR20.2002 permit granted to Limerick via letter dated July 10, 1996.7. ATTACHMENTS  
-None}}
-None}}

Revision as of 17:43, 9 July 2018

CY-TM-170-300, Rev. 3, Offsite Dose Calculation Manual
ML14120A337
Person / Time
Site: Three Mile Island  Constellation icon.png
Issue date: 04/25/2014
From:
Exelon Generation Co, Exelon Nuclear
To:
NRC/FSME, Office of Nuclear Reactor Regulation
References
CY-TM-170-300, Rev 3
Download: ML14120A337 (225)


Text

CY-TM-1 70-300 Exelon. Revision 3 Page 1 of 209 Nuclear Level 3 -Information Use OFFSITE DOSE CALCULATION MANUAL (ODCM)INTRODUCTION The OFFSITE DOSE CALCULATION MANUAL (ODCM) is a supporting document of the Three Mile Island Nuclear Station (TMI) Unit 1 and Unit 2 PDMS Technical Specifications and implements TMI radiological effluent controls.

The ODCM contains the controls, bases, and surveillance requirements for liquid and gaseous radiological effluents.

In addition, the ODCM describes the methodology and parameters to be used in the calculation of off-site doses due to radioactive liquid and gaseous effluents.

This document also describes the methodology used for calculation of the liquid and gaseous effluent monitoring instrumentation alarm/trip set points. Liquid and Gaseous Radwaste Treatment System configurations are also included.The ODCM also is used to define the requirements for the TMI radiological environmental monitoring program (REMP) and contains a list and graphical description of the specific sample locations used in the REMP.The ODCM is maintained at the Three Mile Island (TMI) site for use as a reference guide and training document of accepted methodologies and calculations.

Changes in the calculation methods or parameters will be incorporated into the ODCM to ensure the ODCM represents the present methodology in all applicable areas. Changes to the ODCM will be implemented in accordance with the TMI-1 and TMI-2 PDMS Technical Specifications.

The ODCM follows the methodology and models suggested by NUREG-0133, and Regulatory Guide 1.109, Revision 1 for calculation of off-site doses due to plant effluent releases.Simplifying assumptions have been applied in this manual where applicable to provide a more workable document for implementation of the Radiological Effluent Controls requirements.

TMI implements the TMI Radiological Effluent Controls Program and Regulatory Guide 1.21, Revision 1 (Annual Radioactive Effluent Release Report) requirements by use of a computerized system used to determine TMI effluent releases and to update cumulative effluent doses.This procedure replaces 6610-PLN-4200.01.

CY-TM-1 70-300 Revision 3 Page 2 of 209 TABLE OF CONTENTS PART I TMI-1 RADIOLOGICAL EFFLUENT CONTROLS Section Page 1.0 DEFINITIONS 13 Table 1-1, Frequency Notation 18 Map1.1, Gaseous Effluent Release Points and Liquid Effluent Outfall Locations 19 2.0 RADIOLOGICAL EFFLUENT CONTROLS AND BASES 20 2.1 Radioactive Effluent Instrumentation 20 2.1.1 Radioactive Liquid Effluent Instrumentation 20 Table 2.1-1, Radioactive Liquid Effluent Instrumentation 22 2.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 23 Table 2.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation 24 2.2 Radioactive Effluent Controls 30 2.2.1 Liquid Effluent Controls 30 2.2.2 Gaseous Effluent Controls 34 2.2.3 Total Radioactive Effluent Controls 41 3.0 SURVEILLANCES 44 3.1 Radioactive Effluent Instrumentation 44 3.1.1 Radioactive Liquid Effluent Instrumentation 44 Table 3.1-1, Radioactive Liquid Effluent Monitoring Instrumentation Surveillance Requirements 45 3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 47 Table 3.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 48 CY-TM-170-300 Revision 3 Page 3 of 209 TABLE OF CONTENTS (Cont'd)PART I TMI-1 RADIOLOGICAL EFFLUENT CONTROLS Section Page 3.2 Radiological Effluents 53 3.2.1 Liquid Effluents 53 Table 3.2-1, Radioactive Liquid Waste Sampling and Analysis Program 55 3.2.2 Gaseous Effluents 58 Table 3.2-2, Radioactive Gaseous Waste Sampling and Analysis Program 60 3.2.3 Total Radioactive Effluents 64 4.0 PART I REFERENCES 65 CY-TM-1 70-300 Revision 3 Page 4 of 209 TABLE OF CONTENTS (Cont'd)PART II TMI-2 RADIOLOGICAL EFFLUENT CONTROLS Section Page 1.0 DEFINITIONS 67 Table 1.1, Frequency Notation 70 2.0 CONTROLS AND BASES 71 2.1 Radioactive Effluent Instrumentation 71 2.1.1 Radioactive Liquid Effluent Instrumentation 71 2.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 71 Table 2.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation 73 2.2 Radioactive Effluent Controls 74 2.2.1 Liquid Effluent Controls 74 2.2.2 Gaseous Effluent Controls 78 2.2.3 Total Radioactive Effluent Controls 85 3.0 SURVEILLANCES 87 3.1 Radioactive Effluent Instrumentation 87 3.1.1 Radioactive Liquid Effluent Instrumentation 87 3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation 87 Table 3.1-2, Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 88 3.2 Radioactive Effluents 89 3.2.1 Liquid Effluents 89 Table 3.2-1, Radioactive Liquid Waste Sampling and Analysis Program 90 3.2.2 Gaseous Effluents 91 CY-TM-170-300 Revision 3 Page 5 of 209 TABLE OF CONTENTS (Cont'd)PART II TMI-2 RADIOLOGICAL EFFLUENT CONTROLS Section Paqe Table 3.2-2, Radioactive Gaseous Waste Sampling and Analysis Program 92 3.2.3 Total Radioactive Effluents 95 4.0 PART II REFERENCES 96 CY-TM-170-300 Revision 3 Page 6 of 209 TABLE OF CONTENTS (Cont'd)PART III EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES Section Pagqe 1.0 LIQUID EFFLUENT MONITORS 98 1.1 TMI-1 and TMI-2 Liquid Radiation Monitor Set Points 98 1.2 TMI Liquid Effluent Release Points and Liquid Radiation Monitor Data 99 1.3 Control of Liquid Releases 101 2.0 LIQUID EFFLUENT DOSE ASSESSMENT 106 2.1 Liquid Effluents

-10 CFR 50 Appendix I 106 2.2 TMI Liquid Radwaste System Dose Calcs Once Per Month 107 2.3 Alternative Liquid Dose Calculational Methodology 108 3.0 TMI LIQUID EFFLUENT WASTE TREATMENT SYSTEM 113 3.1 TMI-1 Liquid Effluent Waste Treatment System 113 3.2 Operability of the TMI-1 Liquid Effluent Waste Treatment System 114 3.3 TMI-2 Liquid Effluent Waste Treatment System 114 4.0 GASEOUS EFFLUENT MONITORS 117 4.1 TMI-1 Noble Gas Monitor Set Points 117 4.2 TMI-1 Particulate and Radioiodine Monitor Set Points 119 4.3 TMI-2 Gaseous Radiation Monitor Set Points 120 4.4 TMI-1 Gaseous Effluent Release Points and Gaseous Radiation Monitor Data 121 4.5 TMI-2 Gaseous Effluent Release Points and Gaseous Radiation Monitor Data 123 4.6 Control of Gaseous Effluent Releases 124 CY-TM-1 70-300 Revision 3 Page 7 of 209 TABLE OF CONTENTS (Cont'd)PART III EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES Section Page 5.0 GASEOUS EFFLUENT DOSE ASSESSMENT 136 5.1 Gaseous Effluents

-Instantaneous Release Limits 136 5.1.1 Noble Gases 136 5.1.1.1 Total Body 136 5.1.1.2 Skin 137 5.1.2 lodines, Tritium and Particulates 138 5.2 Gaseous Effluents

-10 CFR 50 Appendix I 139 5.2.1 Noble Gases 139 5.2.2 lodines, Tritium and Particulates 140 5.3 Gaseous Radioactive System Dose Calculations Once per Month 142 5.4 Alternative Gaseous Dose Calculational Methodology 143 6.0 TMI-1 GASEOUS EFFLUENT WASTE TREATMENT SYSTEM 165 6.1 Description of the TMI-1 Gaseous Radwaste Treatment System 165 6.2 Operability of the TMI-1 Gaseous Radwaste Treatment System 165 7.0 EFFLUENT TOTAL DOSE ASSESSMENT 167 8.0 TMINS RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM (REMP) 168 8.1 Monitoring Program Requirements 168 8.2 Land Use Census 171 8.3 Interlaboratory Comparison Program 173 9.0 PART III REFERENCES 191 CY-TM-1 70-300 Revision 3 Page 8 of 209 TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART III Section TABLES Table 1.1 Table 1.2 Table 2.1 Table 2.2 Table 4.1 Table 4.2 Table 4.3 Table 4.4 Table 4.5 Table 4.6 Table 5.2.1 Table 5.2.2 Table 5.2.3 Table 5.2.4 Table 5.3.1 Table 5.4.1 Table 5.4.2 Table 5.4.3 Table 5.4.4 Table 5.5.1 Paqe TMI Liquid Release Point and Liquid Radiation Monitor Data TMI-2 Sump Capacities Liquid Dose Conversion Factors (DCF): DFij Bioaccumulation Factors, BFi TMI-1 Gaseous Release Point and Gaseous Radiation Monitor Data TMI-2 Gaseous Release Point and Gaseous Radiation Monitor Data Dose Factors for Noble Gases and Daughters Atmospheric Dispersion Factors for Three Mile Island -Station Vent Atmospheric Dispersion Factors for Three Mile Island -Ground Release Dose Parameters for Radioiodines and Radioactive Particulate In Gaseous Effluents Pathway Dose Factors, Ri -Infant, Inhalation Pathway Dose Factors, Ri -Child, Inhalation Pathway Dose Factors, Ri -Teen, Inhalation Pathway Dose Factors, Ri -Adult, Inhalation Pathway Dose Factors, Ri -All Age Groups, Ground Plane Pathway Dose Factors, Ri -Infant, Grass-Cow-Milk Pathway Dose Factors, R -Child, Grass-Cow-Milk Pathway Dose Factors, Ri -Teen, Grass-Cow-Milk Pathway Dose Factors, Ri -Adult, Grass-Cow-Milk Pathway Dose Factors, Ri -Infant, Grass-Goat-Milk 102 103 109 112 125 126 127 128 129 130 144 145 146 147 148 149 150 151 152 153 CY-TM-1 70-300 Revision 3 Page 9 of 209 TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART III Section TABLES Table 5.5.2 Table 5.5.3 Table 5.5.4 Table 5.6.1 Table 5.6.2 Table 5.6.3 Table 5.6.4 Table 5.7.1 Table 5.7.2 Table 5.7.3 Table 5.7.4 Table 8.1 Table 8.2 Table 8.3 Table 8.4 Table 8.5 Table 8.6 Table 8.7 Table 8.8 Table 8.9 Table 8.10 Paaqe Pathway Dose Factors, Ri -Child, Grass-Goat-Milk Pathway Dose Factors, Ri -Teen, Grass-Goat-Milk Pathway Dose Factors, Ri -Adult, Grass-Goat-Milk Pathway Dose Factors, Ri -Infant, Grass-Cow-Meat Pathway Dose Factors, Ri -Child, Grass-Cow-Meat Pathway Dose Factors, R i -Teen, Grass-Cow-Meat Pathway Dose Factors, Ri -Adult, Grass-Cow-Meat Pathway Dose Factors, Ri -Infant, Vegetation Pathway Dose Factors, R 1 -Child, Vegetation Pathway Dose Factors, Ri -Teen, Vegetation Pathway Dose Factors, Ri -Adult, Vegetation Sample Collection and Analysis Requirements Reporting Levels for Radioactivity Concentrations in Environmental Samples Detection Capabilities for Environmental Sample Analysis TMINS REMP Station Locations

-Air Particulate and Air Iodine TMINS REMP Station Locations

-Direct Radiation TMINS REMP Station Locations

-Surface Water TMINS REMP Station Locations

-Aquatic Sediment TMINS REMP Station Locations

-Milk TMINS REMP Station Locations

-Fish TMINS REMP Station Locations

-Food Products 154 155 156 157 158 159 160 161 162 163 164 174 180 181 184 184 186 186 187 187 187 CY-TM-1 70-300 Revision 3 Page 10 of 209 TABLE OF CONTENTS (Cont'd)EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES PART III Section MAPS Paqe MAP 8.1 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations within 1 Mile of the Site MAP 8.2 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations within 5 miles of the Site MAP 8.3 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Greater than 5 miles from the Site 188 189 190 FIGURES Figure 1.1 Figure 1.2 Figure 3.1 Figure 3.2 Figure 4.1 Figure 4.2 Figure 4.3 Figure 4.4 Figure 4.5 Figure 6.1 TMI-1 Liquid Effluent Pathways TMI-2 Liquid Effluent Pathways TMI-1 Liquid Radwaste TMI-1 Liquid Waste Evaporators TMI-1 Gaseous Effluent Pathways TMI-1 Auxiliary and Fuel Handling Buildings Effluent Pathways TMI-1 Reactor Building Effluent Pathway TMI-1 Condenser Offgas Effluent Pathway TMI-2 Gaseous Effluent Filtration System/Pathways Waste Gas System 104 105 115 116 131 132.133 134 135 166 CY-TM-1 70-300 Revision 3 Page 11 of 209 TABLE OF CONTENTS (Cont'd)PART IV REPORTING REQUIREMENTS Section Page 1.0 TMI ANNUAL RADIOLOGICAL ENVIRONMENTAL OPERATING REPORT 194 2.0 TMI ANNUAL RADIOACTIVE EFFLUENT RELEASE REPORT 195 3.0 PART IV REFERENCES 197 APPENDICES A. Pathway Dose Rate Parameter (Pi) 198 B. Inhalation Pathway Dose Factor (Ri) 199 C. Ground Plane Pathway Dose Factor (Ri) 200 D. Grass-Cow-Milk Pathway Dose Factor (R 1) 201 E. Cow-Meat Pathway Dose Factor .(Ri) 203 F. Vegetation Pathway Dose Factor (Ri) 205 APPENDIX A -F REFERENCES 206 CY-TM-1 70-300 Revision 3 Page 12 of 209 PART I TMI-1 RADIOLOGICAL EFFLUENT CONTROLS CY-TM-170-300 Revision 3 Page 13 of 209 1.0 DEFINITIONS The following terms are defined for uniform interpretation of these controls and surveillances.

1.1 Reactor Operating Conditions 1.1.1 Cold Shutdown The reactor is in the cold shutdown condition when it is subcritical by at least one percent delta k/k and Tavg is no more than 200 0 F. Pressure is defined by Technical Specification 3.1.2.1.1.2 Hot Shutdown The reactor is in the hot shutdown condition when it is subcritical by at least one percent delta k/k and Tavg is at or greater than 525 0 F.1.1.3 Reactor Critical The reactor is critical when the neutron chain reaction is self-sustaining and Keff = 1.0.1.1.4 Hot Standby The reactor is in the hot standby condition when all of the following conditions exist: a. Tavg is greater than 5250F b. The reactor is critical c. Indicated neutron power on the power range channels is less than two percent of rated power. Rated power is defined in Technical Specification Definition 1.1.1.1.5 Power Operation The reactor is in a power operating condition when the indicated neutron power is above two percent of rated power as indicated on the power range channels.

Rated power is defined in Technical Specification Definition 1.1.

CY-TM-1 70-300 Revision 3 Page 14 of 209 1.1.6 Refueling Shutdown The reactor is in the refueling shutdown condition when, even with all rods removed, the reactor would be subcritical by at least one percent delta k/k and the coolant temperature at the decay heat removal pump suction is no more than 140 0 F. Pressure is defined by Technical Specification 3.1.2. A refueling shutdown refers to a shutdown to replace or rearrange all or a portion of the fuel assemblies and/or control rods.1.1.7 Refueling Operation An operation involving a change in core geometry by manipulation of fuel or control rods when the reactor vessel head is removed.1.1.8 Refueling Interval The time between normal refuelings of the reactor. This is defined as once per 24 months.1.1.9 Startup The reactor shall be considered in the startup mode when the shutdown margin is reduced with the intent of going critical.1.1.10 Tave Tave is defined as the arithmetic average of the coolant temperatures in the hot and cold legs of the loop with the greater number of reactor coolant pumps operating, if such a distinction of loops can be made.1.1.11 Heatup -Cooldown Mode The heatup-cooldown mode is the range of reactor coolant temperature greater than 200OF and less than 5250F.1.2 Operable A system, subsystem, train, component or device, shall be OPERABLE or have OPERABILITY when it is capable of performing it's specified function(s), and when all necessary attendant instrumentation, controls, electrical power, cooling or seal water, lubrication or other auxiliary equipment that are required for the system, subsystem, train, component, or device to perform its function(s), are also capable of performing their related support function(s).

1.3 Instrument Channel An instrument channel is the combination of sensor, wires, amplifiers, and output devices, which are connected for the purpose of measuring the value of a CY-TM-1 70-300 Revision 3 Page 15 of 209 process variable, for the purpose of observation, control, and/or protection.

An instrument channel may be either analog or digital.1.4 Instrumentation Surveillance 1.4.1 Channel Test A CHANNEL TEST shall be the injection of a simulated signal into the channel as close to the sensor as practical to verify OPERABILITY, including alarm and/or trip functions.

1.4.2 Channel Check A CHANNEL CHECK shall be the qualitative assessment of channel behavior during operation by observation.

This determination shall include, where possible, comparison of the channel indication and/or status with other indications and/or status derived from independent instrumentation channels measuring the same parameter.

1.4.3 Source Check A SOURCE CHECK shall be the qualitative assessment of channel response when the channel sensor is exposed to a radioactive source.1.4.4 Channel Calibration An instrument CHANNEL CALIBRATION is a test, and adjustment (if necessary), to establish that the channel output responds with acceptable range and accuracy to known values of the parameter, which the channel measures, or an accurate simulation of these values.Calibration shall encompass the entire channel, including equipment actuation, alarm, or trip and shall be deemed to include the channel test.1.5 Dose Equivalent 1-131 The DOSE EQUIVALENT 1-131 shall be that concentration of 1-131 (microcurie/gram), which alone would produce the same thyroid dose as the quantity and isotopic mixture of 1-131, 1-132, I-133, 1-134, and 1-135 actually present. The thyroid dose conversion factors used for this calculation shall be those listed in Table III of TID 14844, "Calculation of Distance Factors for Power and Test Reactor Sites". [Or in Table E-7 of NRC Regulatory Guide 1.109, Revision 1, October, 1977.]

CY-TM-170-300 Revision 3 Page 16 of 209 1.6 Offsite Dose Calculation Manual (ODCM)The OFFSITE DOSE CALCULATION MANUAL (ODCM) contains the methodology and parameters used in the calculation of offsite doses resulting from radioactive gaseous and liquid effluent, in the calculation of gaseous and liquid effluent monitoring Alarm/Trip Setpoints,.

and in the conduct of the Radiological Environmental Monitoring Program. The ODCM also contains (1)the Radiological Effluent Controls, (2) the Radiological Environmental Monitoring Program and (3) descriptions of the information that should be included in the Annual Radiological Environmental Operating and Annual Radioactive Effluent Release Reports.1.7 Gaseous Radwaste Treatment The GASEOUS RADWASTE TREATMENT SYSTEM is the system designed and installed to reduce radioactive gaseous effluent by collecting primary coolant system off gases from the primary system and providing for delay or holdup for the purpose of reducing the total radioactivity prior to release to the environment.

1.8 Ventilation Exhaust Treatment System A VENTILATION EXHAUST TREATMENT SYSTEM is any system designed and installed to reduce gaseous radioiodine or radioactive material in particulate form in effluent by passing ventilation or vent exhaust gases through charcoal absorbers and/or HEPA filters for the purpose of removing iodine or particulates from the gaseous exhaust system prior to the release to the environment.

Engineered Safety Feature (ESF) atmospheric cleanup systems are not considered to be VENTILATION EXHAUST TREATMENT SYSTEMS.1.9 Purge -Purging PURGE or PURGING is the controlled process of discharging air or gas from a confinement to maintain temperature, pressure, humidity, concentration or other operating conditions in such a manner that replacement air or gas is required to purify the confinement.

1.10 Venting VENTING is the controlled process of discharging air as gas from a confinement to maintain temperature, pressure, humidity, concentration or other operating conditions in such a manner that replacement air or gas is not provided.

Vent used in system name does not imply a VENTING process.1.11 Member(s) of the Public MEMBER OF THE PUBLIC means any individual except when that individual is receiving an occupational dose.

CY-TM-170-300 Revision 3 Page 17 of 209 1.12 Site Boundary The SITE BOUNDARY used as the basis for the limits on the release of gaseous effluents is as defined in Section 2.1.2.2 and shown on Figure 2.1-3 of the TMI-1 FSAR. This boundary line includes portions of the Susquehanna River surface between the east bank of the river and Three Mile Island and between Three Mile Island and Shelley Island.The SITE BOUNDARY used as the basis for the limits on the release of liquid effluents is as shown in Figure 1.1 in Part I of this ODCM.1.13 Frequency Notation The FREQUENCY NOTATION specified for the performance of Surveillance Requirements shall correspond to the intervals defined in Table 1-1. All Surveillance Requirements shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% of the surveillance interval.

The 25% extension applies to all frequency intervals with the exception of "F." No extension is allowed for intervals designated "F." 1.14 Occupational Dose OCCUPATIONAL DOSE means the dose received by an individual in the course of employment in which the individual's assigned duties involve exposure to radiation or to radioactive material from licensed and unlicensed sources of radiation, whether in the possession of the licensee or other person.Occupational dose does not include doses received from background radiation, from any medical administration the individual has received; from exposure to individuals administered radioactive material and released under 10CFR35.75, from voluntary participation in medical research programs, or as a member of the public.

CY-TM-1 70-300 Revision 3 Page 18 of 209 Table 1-1 Frequency Notation Notation Frequency S Shiftly (once per 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br />)D Daily (once per 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />)W Weekly (once per 7 days)M Monthly (once per 31 days)Q Quarterly (once per 92 days)S/A Semi-Annually (once per 184 days)R Refueling Interval (once per 24 months)P S/U Prior to each reactor startup, if not done during the previous 7 days P Completed prior to each release N/A (NA) Not applicable E Once per 18 months F Not to exceed 24 months Bases Section 1.13 establishes the limit for which the specified time interval for Surveillance Requirements may be extended.

It permits an allowable extension of the normal surveillance interval to facilitate surveillance scheduling and consideration of plant operating conditions that may not be suitable for conducting the surveillance; e.g., transient conditions or other ongoing surveillance or maintenance activities.

It also provides flexibility to accommodate the length of a fuel cycle for surveillances that are specified to be performed at least once each REFUELING INTERVAL.

It is not intended that this provision be used repeatedly as a convenience to extend surveillance intervals beyond that specified for surveillances that are not performed once each REFUELING INTERVAL.

Likewise, it is not the intent that REFUELING INTERVAL surveillances be performed during power operation unless it is consistent with safe plant operation.

The limitation of Section 1.13 is based on engineering judgment and the recognition that the most probable result of any particular surveillance being performed is the verification of conformance with the Surveillance Requirements.

This provision is sufficient to ensure that the reliability ensured through surveillance activities is not significantly degraded beyond that obtained from the specified surveillance interval.

CY-TM-1 70-300 Revision 3 Page 19 of 209 Map 1.1 Gaseous Effluent Release Points and Liquid Effluent Outfall Locations CY-TM-1 70-300 Revision 3 Page 20 of 209 2.0 RADIOLOGICAL EFFLUENT CONTROLS AND BASES 2.1 Radioactive Effluent Instrumentation 2.1.1 Radioactive Liquid Effluent Instrumentation CONTROL: The radioactive liquid effluent monitoring instrumentation channels shown in Table 2.1-1 shall be OPERABLE with their alarm/trip setpoints set to ensure that the limits of Control 2.2.1.1 are not exceeded.

The alarm/trip setpoints of these channels shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:

At all times *ACTION: a. With a radioactive liquid effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required by the above control, immediately suspend the release of radioactive liquid effluent monitored by the affected channel or declare the channel inoperable.

b. With less than the minimum number of radioactive liquid effluent monitoring instrumentation channels OPERABLE, take the ACTION shown in Table 2.1 -1. Exert best efforts to return the instrumentation to OPERABLE status within 30 days and, if unsuccessful, explain in the next Annual Effluent Release Report why the inoperability was not corrected in a timely manner.For WDL-FT-84, and RM-L-6, operability is not required when discharges are positively controlled through the closure of WDL-V-257.

For RM-L-12 and associated IWTS/IWFS flow interlocks, operability is not required when discharges are positively controlled through the closure of IW-V-72, 75 and IW-V-280, 281.For SR-FT-146, operability is not required when discharges are positively controlled through the closure of WDL-V-257, IW-V-72, 75 and IW-V-280, 281.

CY-TM-1 70-300 Revision 3 Page 21 of 209 BASES The radioactive liquid effluent instrumentation is provided to monitor and control, as applicable, the releases of radioactive materials in liquid effluent during actual or potential releases.

The alarm/trip setpoints for these instruments shall be calculated in accordance with NRC approved methods in the ODCM to ensure that the alarm/trip will occur prior to exceeding ten times the effluent concentrations of 10 CFR Part 20.

CY-TM-170-300 Revision 3 Page 22 of 209 Table 2.1-1 Radioactive Liquid Effluent Instrumentation Minimum Channels Operable Instrument ACTION 1. Gross Radioactivity Monitors Providing Automatic Termination of Release a. Unit 1 Liquid Radwaste Effluent Line (RM-L6)b. IWTS/IWFS Discharge Line (RM-L12)2. Flow Rate Measurement Devices a. Unit 1 Liquid Radwaste Effluent Line (WDL-FT-84)

b. Station Effluent Discharge (SR-FT-146) 1 1 18 20 1 1 21 21 Table Notation ACTION 18 With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases may continue, provided that prior to initiating a release: 1. At least two independent samples are analyzed in accordance with Surveillances 3.2.1.1.1 and 3.2.1.1.2 and;2. At least two technically qualified members of the Unit staff independently verify the release rate calculations and verify the discharge valve lineup.3. The TMI Plant Manager shall approve each release. Otherwise, suspend release of radioactive effluents via this pathway.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may commence or continue provided that grab samples are collected and analyzed for gross radioactivity (beta or gamma) at a limit of detection of at least lx10-7 microcuries/ml, prior to initiating a release and at least once per 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> during release.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, radioactive effluent releases via this pathway may continue, provided the flow rate is estimated at least once per 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> during actual releases.

Pump curves may be used to estimate flow.ACTION 20 ACTION 21 CY-TM-1 70-300 Revision 3 Page 23 of 209 2.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation CONTROL: The radioactive gaseous process and effluent monitoring instrumentation channels shown in Table 2.1-2 shall be OPERABLE with their alarm/trip setpoints set to ensure that the limits of Control 2.2.2.1 are not exceeded.

The alarm/trip setpoints of these channels shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:

As shown in Table 2.1-2 ACTION: a. With a radioactive gaseous process or effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required by the above control, immediately suspend the release of radioactive effluent monitored by the affected channel or declare the channel inoperable.

b. With less than the minimum number of radioactive gaseous process or effluent monitoring instrumentation channels OPERABLE, take the ACTION shown in Table 2.1-2. Exert best efforts to return the instrumentation to OPERABLE status within 30 days and, if unsuccessful, explain in the next Annual Effluent Release Report why the inoperability was not corrected in a timely manner.BASES The radioactive gaseous effluent instrumentation is provided to monitor and control, as applicable, the releases of radioactive materials in gaseous effluent during actual or potential releases.

The alarm/trip setpoints for these instruments shall be calculated in accordance with NRC approved methods in the ODCM to provide reasonable assurance that the annual releases are within the limits specified in 10 CFR 20.1301.The low range condenser offgas noble gas activity monitors also provide data for determination of steam generator primary to secondary leakage rate. Channel operability requirements are based on an AmerGen letter#5928-06-20449, "Request to Revise Condenser Vent System Low Range Noble Gas Monitor Operability Requirements", Pamela B. Cowan to U.S.N.R.C., May 25, 2006.

CY-TM-1 70-300 Revision 3 Page 24 of 209 Table 2.1-2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUM CHANNEL INSTRUMENT OPERABLE APPLICABILITY ACTION 1. Waste Gas Holdup System a. Noble Gas Activity Monitor (RM-A-7) 1 25 B. Effluent System Flow Rate Measuring Device (WDG-FT-123) 1 261 2. Waste Gas Holdup System Explosive Gas Monitoring System a. Hydrogen Monitor (CA-G-1A/B) 2 ** 30 b. Oxygen Monitor (CA-G-1A/B) 2 ** 30 3. Containment Purge Monitoring System a. Noble Gas Activity Monitor (RM-A-9) 1 # 27 b. Iodine Sampler (RM-A-9) 1 # 31 c. Particulate Sampler (RM-A-9) 1 # 31 d. Effluent System Flow Rate Measuring Device (AH-FR-148A, AH-FR-148B) 1 # 26 e. Sampler Flow Rate Monitor (RM-FI-1231) 1 # 26 4. Condenser Vent System a. Low Range Noble Gas Activity Monitor (RM-A-5Lo or RM-A-15) 1## 32 CY-TM-1 70-300 Revision 3 Page 25 of 209 Table 2.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUM CHANNEL INSTRUMENT OPERABLE APPLICABILITY ACTION 5. Auxiliary and Fuel Handling Building Ventilation System a. Noble Gas Activity Monitor (RM-A-8) or (RM-A-4 and RM-A-6) 1

  • 27 b. Iodine Sampler (RM-A-8 or (RM-A-4 and RM-A-6) 1
  • 31 c. Particulate Sampler (RM-A-8 or (RM-A-4 and RM-A-6) 1
  • 31 d. Effluent System Flow Rate Measuring Devices (AH-FR-149 and 1
  • 26 AH-FR-1 50)e. Sampler Flow Rate Monitor (RM-FI-1230 or RM-A-4\FI and RM-A-6\FI) 1 26 6. Fuel Handling Building ESF Air Treatment System a. Noble Gas Activity Monitor (RM-A-14 or suitable equivalent) 1 .... 27,33 b. Iodine Cartridge N/A(2) .... 31,33 c. Particulate Filter N/A(2) .... 31,33 d. Effluent System Flow (AH-UR-1 104A/B) 1 .... 26,33 e. Sampler Flow Rate Monitor (RM-A-14FI14) 1 26,33 NOTE 2: No instrumentation channel is provided.

However, for determining operability, the equipment named must be installed and functional or the ACTION applies.

CY-TM-1 70-300 Revision 3 Page 26 of 209 Table 2.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUM CHANNEL INSTRUMENT OPERABLE APPLICABILITY ACTION 7. Chemical Cleaning Building Ventilation System a. Noble Gas Activity Monitor (ALC RM-1-18) 1(3) 27 b. Iodine Sampler (ALC RM-1-18) 1(3) 31 c. Particulate Sampler (ALC RM-1-18) 1 31 8. Waste Handling and Packaging Facility Ventilation System a. Particulate Sampler (WHP-RIT-1) 1 31 9. Respirator and Laundry Maintenance Facility Ventilation System a. Particulate Sampler (RLM-RM-1) 1 31 NOTE 3: Channel only required when liquid radwaste is moved or processed within the facility.

CY-TM-1 70-300 Revision 3 Page 27 of 209 Table 2.1-2 (Cont'd)Table Notation-* At all times-** During waste gas holdup system operation-**

  • Operability is not required when discharges are positively controlled through the closure of WDG-V-47 or where RM-A-8, AH-FT-149 and AH-FT-150 are operable and RM-A-8 is capable of automatic closure of WDG-V-47 During Fuel Handling Building ESF Air Treatment System Operation-# At all times during containment purging-# At all times when condenser vacuum is established

-### During operation of the ventilation system ACTION 25 With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, the contents of the tank may be released to the environment provided that prior to initiating the release: 1. At least two independent samples of the tank's contents are analyzed in accordance with Table 3.2-2, Item A, and 2. At least two technically qualified members of the Unit staff independently verify the release rate calculations and verify the discharge valve lineup.3. The TMI Plant Manager shall approve each release. Otherwise, suspend release of radioactive effluent via this pathway.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may continue provided the flow rate is estimated at least once per 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br />.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may continue provided grab samples are taken at least once per 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> and the initial samples are analyzed for gross activity (gamma scan) within 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> after the channel has been declared inoperable.

If RM-A-9 is declared inoperable, see also Technical Specification 3.5.1, Table 3-5.1, Item C.3.f.ACTION 26 ACTION 27 CY-TM-1 70-300 Revision 3 Page 28 of 209 Table 2.1-2 Notations (Cont'd)ACTION 30 1.With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, a grab sample shall be collected and analyzed for the inoperable gas channel(s) at least once per 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />. With both channels inoperable, a grab sample shall be collected and analyzed for the inoperable gas channel(s):

ACTION 31 ACTION 32 (a) at least once per 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> during degassing operations.(b) at least once per 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> during other operations (e.g. Feed and Bleed).2. If the inoperable gas channel(s) is not restored to service within 14 days, a special report shall be submitted to the Regional Administrator of the NRC Region I Office and a copy to the Director, Office of Inspection and Enforcement within 30 days of declaring the channel(s) inoperable.

The report shall describe (a) the cause of the monitor inoperability, (b) action being taken to restore the instrument to service, and (c) action to be taken to prevent recurrence.

With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may continue provided that within four hours after the channel has been declared inoperable, samples are continuously collected with auxiliary sampling equipment.

With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, effluent releases via this pathway may continue for up to 14 days, provided that grab samples are taken and analyzed.If the primary-to-secondary leak rate was unstable*, or was indicating an increasing trend at the initial time when there was no operable channel of the Condenser Vent System Low Range Noble Gas Activity Monitor, analyze grab samples of the reactor coolant system and Condenser OffGas once every 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> to provide an indication of primary-to-secondary leakage. Subsequent sample frequency shall be in accordance with Table 1 based on the last sample result. Otherwise, analyze grab samples of the reactor coolant system and Condenser OffGas to provide an indication of primary-to-secondary leakage at the minimum frequency indicated in Table 1, below:

CY-TM-170-300 Revision 3 Page 29 of 209 Table 2.1-2 Notations (Cont'd)Table 1 Minimum Frequency of Grab Samples When No Condenser Vent System Low Range Noble Gas Activity Monitor is Operable Existing Total Primary-to-Secondary Leak Rate Frequency of Grab Samples (based on last monitor reading or sample result)0 to < 5 GPD Once per 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> 5 to < 30 GPD Once per 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> 30 to < 75 GPD Once per 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> 75 GPD or greater Place the unit in at least HOT STANDBY within the next 6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br />, and at least HOT SHUTDOWN within the following 6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br />, and at least COLD SHUTDOWN within the subsequent 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />.*Unstable is defined as > 10% increase during a 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> period, as stated in the EPRI Guidelines.

Condenser Vent System Low Range Noble Gas Activity Monitor inoperable channels should be restored to operability as rapidly as practical.

After 14 days, if one OPERABLE channel is not returned to service, within I hour, the provisions of Technical Specification 3.0.1 apply, as if this Control were a Tech Spec Limiting Condition for Operation.

ACTION 33 With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, either restore the inoperable channel to OPERABLE status within 7 days, or prepare and submit a special report within 30 days outlining the action(s) taken, the cause of the inoperability, and plans and schedule for restoring the system to OPERABLE status.

CY-TM-170-300 Revision 3 Page 30 of 209 2.2 Radioactive Effluent Controls 2.2.1 Liquid Effluent Controls 2.2.1.1 Liquid Effluent Concentration CONTROL: The concentration of radioactive material released at anytime from the unit to unrestricted areas shall be limited to ten times the concentrations specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2, Column 2 for radionuclides other than dissolved or entrained noble gases. For dissolved or entrained noble gases, the concentration shall be limited to 3E-3 uCi/cc total activity.APPLICABILITY:

At all times ACTION: With the concentration of radioactive material released from the unit to unrestricted areas exceeding the above limits, immediately restore concentrations within the above limits.BASES This control is provided to ensure that the concentration of radioactive materials released in liquid waste effluent from the unit to unrestricted areas will be less than ten times the concentration levels specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2. This limitation provides additional assurance that the levels of radioactive materials in bodies of water outside the site will not result in exposures with (1) the Section II.A design objectives of Appendix 1, 10 CFR Part 50, to a MEMBER OF THE PUBLIC and (2) the limits of 10 CFR Part 20.1301 to the population.

The concentration limit for noble gases is based upon the assumption the Xe-1 35 is the controlling radioisotope and its MPC in air (submersion) was converted to an equivalent concentration in water using the methods described in International Commission on Radiological Protection (ICRP)Publication

2.

CY-TM-170-300 Revision 3 Page 31 of 209 2.2.1.2 Liquid Effluent Dose CONTROL The dose or dose commitment to a MEMBER OF THE PUBLIC from radioactive materials in liquid effluents released from the unit to the SITE BOUNDARY shall be limited: a. During any calendar quarter to less than or equal to 1.5 mrem to the total body and to less than or equal to 5 mrem to any organ.b. During any calendar year to less than or equal to 3 mrem to the total body and to less than or equal to 10 mrem to any organ.APPLICABILITY:

At all times ACTION: a. With the calculated dose from the release of radioactive materials in liquid effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report, which identifies the cause(s) for exceeding the limit(s), and defines the corrective actions to be taken to reduce the releases of radioactive materials in liquid effluents during the remainder of the current calendar quarter and during the subsequent 3 calendar quarters so that the cumulative dose or dose commitment to any individual from such releases during these four calendar quarters is within 3 mrem to the total body and 10 mrem to any organ. This Special Report shall also include (1) the result of radiological analyses of the drinking water source, and (2) the radiological impact on finished drinking water supplies with regard to the requirements of 40 CFR 141, Safe Drinking Water Act.

CY-TM-1 70-300 Revision 3 Page 32 of 209 BASES This control and associated action is provided to implement the requirements of Sections II.A, Ill.A, and IV.A of Appendix I, 10 CFR Part 50. The Control implements the guides set forth in Section II.A of Appendix I. The ACTION statements provide the required operating flexibility and at the same time implement the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive material in liquid effluents will be kept "as low as is reasonably achievable".

Also, for fresh water sites with drinking water supplies which can be potentially affected by plant operations, there is reasonable assurance that the operation of the facility will not result in radionuclide concentrations in the finished drinking water that are in excess of the requirements of 10 CFR 20.The dose calculations in the ODCM implement the requirements in Section III.A. of Appendix I that conformance with the guides of Appendix I is to be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.

The equations specified in the ODCM for calculating the doses due to the actual release rates of radioactive materials in liquid effluents are consistent with the methodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October, 1977, and Regulatory Guide 1.113,"Estimating Aquatic Dispersion of Effluents from Accidental and Routine Reactor Releases for the Purpose of Implementing Appendix I," April, 1977. NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.113.

CY-TM-170-300 Revision 3 Page 33 of 209 2.2.1.3 Liquid Radwaste Treatment System CONTROL: The appropriate portions of the liquid radwaste treatment system shall be used to reduce the radioactive materials in liquid wastes prior to their discharge when the projected doses due to the liquid effluent from the unit to unrestricted areas would exceed 0.06 mrem to the total body or 0.2 mrem to any organ in any calendar month.APPLICABILITY:

At all times ACTION: a. With radioactive liquid waste being discharged without treatment and in excess of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which includes the following information:

1. Explanation of why liquid radwaste was being discharged without treatment, identification of any inoperable equipment or subsystems, and the reason for inoperability, 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and, 3. A summary description of action(s) taken to prevent a recurrence BASES The requirement that the appropriate portions of this system be used, when specified, provides assurance that the releases of radioactive materials in liquid effluents will be kept as low as is reasonably achievable.

This control implements the requirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50 and the design objective given in Section II.D of Appendix I to 10 CFR Part 50. The intent of Section ll.D. is to reduce effluents to as low as is reasonably achievable in a cost effective manner. This control satisfies this intent by establishing a dose limit which is a small fraction (25%) of Section II.A of Appendix 1, 10 CFR Part 50 dose requirements.

This margin, a factor of 4, constitutes a reasonable reduction.

CY-TM-1 70-300 Revision 3 Page 34 of 209 2.2.1.4 Liquid Holdup Tanks CONTROL The quantity of radioactive material contained in each of the following tanks shall be limited to less than or equal to 10 curies, excluding tritium and dissolved or entrained noble gases.a. Outside temporary tank APPLICABILITY:

At all times.ACTION: a. With the quantity of radioactive material in any of the above listed tanks exceeding the above limit, immediately suspend all additions of radioactive material to the tank and within 48 hours5.555556e-4 days <br />0.0133 hours <br />7.936508e-5 weeks <br />1.8264e-5 months <br /> reduce the tank contents to within the limit.BASES Restricting the quantity of radioactive material contained in the specified tanks provides assurance that in the event of an uncontrolled release of the tanks' contents, the resulting concentrations would be less than the limits of 10 CFR Part 20.1001-20-20.2401, Appendix B, Table 2, Column 2, at the nearest potable water supply and the nearest surface water supply in an unrestricted area.2.2.2 Gaseous Effluent Controls 2.2.2.1 Gaseous Effluent Dose Rate CONTROL: The dose rate due to radioactive materials released in gaseous effluent from the site shall be limited to the following:

a. For noble gases: less than or equal to 500 mrem/yr to the total body and less than or equal to 3000 mrem/yr to the skin, and b. For 1-131, 1-133, tritium and all radionuclides in particulate form with half lives greater than 8 days: less than or equal to 1500 mrem/yr to any organ.APPLICABILITY:

At all times CY-TM-1 70-300 Revision 3 Page 35 of 209 ACTION: With the release rate(s) exceeding the above limits, immediately decrease the release rate to comply with the above limit(s).BASES The control implements the requirement in Technical Specification (6.8.4.b (7). This specification is provided to ensure that the dose from radioactive materials in gaseous effluents at and beyond the SITE BOUNDARY will be within the annual dose limits of 10 CFR Part 20. The annual dose limits are the doses associated with 10 times the concentrations of 10 CFR Part 20, Appendix B, Table 2, Column 1. These limits provide reasonable assurance that radioactive material discharged in gaseous effluents will not result in the exposure of a MEMBER OF THE PUBLIC, either within or outside the SITE BOUNDARY, to annual average concentrations exceeding the limits specified in Appendix B, Table 2 of 10 CFR Part 20.1302. For MEMBERS OF THE PUBLIC who may at times be within the SITE BOUNDARY, the occupancy of the MEMBER OF THE PUBLIC will be sufficiently low to compensate for any increase in the atmospheric diffusion factor above that for the exclusion area boundary.

The specified release rate limits restrict, at all times, the corresponding gamma and beta dose rates above background to a MEMBER OF THE PUBLIC at or beyond the SITE BOUNDARY to less than or equal to 500 mrem/year to the total body, or to less than or equal to 3000 mrem/year to the skin. These release rate limits also restrict, at all times, the corresponding thyroid dose rate above background to a child via the inhalation pathway to less than or equal to 1500 mrem/year (NUREG 1301).2.2.2.2 Gaseous Effluents Dose-Noble Gases CONTROL: The air dose due to noble gases released in gaseous effluents from the unit to areas at and beyond the SITE BOUNDARY shall be limited to the following:

a. During any calendar quarter: less than or equal to 5 mrad for gamma radiation and less than or equal to 10 mrad for beta radiation
and, CY-TM-1 70-300 Revision 3 Page 36 of 209 b. During any calendar year: less than or equal to 10 mrad for gamma radiation and less than or equal to 20 mrad for beta radiation.

APPLICABILITY:

At all times ACTION: a. With the calculated air dose from radioactive noble gases in gaseous effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit(s) and defines the corrective actions that have been taken to reduce the releases and the proposed corrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.BASES This control applies to the release of radioactive materials in gaseous effluents from TMI-I.This control and associated action is provided to implement the requirements of Section II.B, III.A and IV.A of Appendix I, 10 CFR Part 50. The Control implements the guides set forth in Section 1l.B of Appendix I. The ACTION statements provide the required operating flexibility and at the same time implement the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive material in gaseous effluents will be kept "as low as is reasonably achievable." The Surveillance Requirements implement the requirements in Section III.A of Appendix I that conformance with the guides of Appendix I be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through the appropriate pathways is unlikely to be substantially underestimated.

The dose calculation methodology and parameters established in the ODCM for calculating the doses due to the actual release rates of radioactive noble gases in gaseous effluents are consistent with the methodology provided in Regulatory Guide 1.109,"Calculation of Annual Doses to Man from Routine Release of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977 and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in CY-TM-170-300 Revision 3 Page 37 of 209 Routine Releases from Light-Water Cooled Reactors", Revision 1, July 1977. The ODCM equations provided for determining the air doses at and beyond the SITE BOUNDARY are based upon the historical average atmospheric conditions.

NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.111.2.2.2.3 Dose -Iodine-131, Iodine-133, Tritium, and Radionuclides in Particulate Form CONTROL: The dose to a MEMBER OF THE PUBLIC from Iodine-1 31, Iodine-133, Tritium, and all radionuclides in particulate form with half-lives greater than 8 days, in gaseous effluents released from the unit to areas at and beyond the SITE BOUNDARY shall be limited to the following:

a. During any calendar quarter: less than or equal to 7.5 mrem to any organ, and b. During any calendar year: less than or equal to 15 mrem to any organ.APPLICABILITY:

At all times ACTION:.With the calculated dose from the release of Iodine-131, Iodine-1 33, Tritium, and radionuclides in particulate form with half-lives greater than 8 days, in gaseous effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit and defines the corrective actions that have been taken to reduce the releases and the proposed corrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.BASES This control applies to the release of radioactive materials in gaseous effluents from TMI-I.This control and associated action is provided to implement the requirements of Section II.C, III.A and IV.A of Appendix I, 10 CFR Part 50. The Controls are the guides set forth in CY-TM-1 70-300 Revision 3 Page 38 of 209 Section II.C of Appendix I. The ACTION statement provides the required operating flexibility and at the same time implements the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive materials in gaseous effluents will be kept "as low as is reasonably achievable." The ODCM calculational methods specified in the surveillance requirements implement the requirements in Section III.A of Appendix I that conformance with the guides of Appendix I be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.

The ODCM calculational methodology and parameters for calculating the doses due to the actual release rates of the subject materials are consistent with the methodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October, 1977 and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors" Revision 1, July, 1977. These equations also provide for determining the actual doses based upon the historical average atmospheric conditions.

The release rate controls for iodine-131, iodine-133, tritium and radionuclides in particulate form with half lives greater than 8 days are dependent upon the existing radionuclide pathways to man, in areas at and beyond the SITE BOUNDARY.

The pathways that were examined in the development of these calculations were: 1) individual inhalation of airborne radionuclides, 2) deposition of radionuclides onto green leafy vegetation with subsequent consumption by man, 3) deposition onto grassy areas where milk animals and meat producing animals graze with consumption of the milk and meat by man, and 4) deposition on the ground with subsequent exposure of man.2.2.2.4 Gaseous Radwaste Treatment System CONTROL The GASEOUS RADWASTE TREATMENT SYSTEM and the VENTILATION EXHAUST TREATMENT SYSTEM shall be OPERABLE.

The appropriate portions of the GASEOUS RADWASTE TREATMENT SYSTEM shall be used to reduce radioactive materials in the gaseous waste prior to their discharge when the monthlyprojected gaseous effluent air doses due to untreated gaseous effluent releases from the unit CY-TM-1 70-300 Revision 3 Page 39 of 209 would exceed 0.2 mrad for gamma radiation and 0.4 mrad for beta radiation.

The appropriate portions of the VENTILATION EXHAUST TREATMENT SYSTEM shall be used to reduce radioactive materials in gaseous waste prior to their discharge when the monthly projected doses due to gaseous effluent releases from the site would exceed 0.3 mrem to any organ.APPLICABILITY:

At all times ACTION: a. With the GASEOUS RADWASTE TREATMENT SYSTEM and/or the VENTILATION EXHAUST TREATMENT SYSTEM inoperable for more than a month or with gaseous waste being discharged without treatment and in excess of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which includes the following information:

1. Identification of the inoperable equipment or subsystems and the reason for inoperability, 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and 3. A summary description of action(s) taken to prevent a recurrence BASES The use of the GASEOUS RADWASTE TREATMENT SYSTEM and the VENTILATION EXHAUST TREATMENT SYSTEM ensures that gaseous effluents are treated as appropriate prior to release to the environment.

The appropriate portions of this system provide reasonable assurance that the releases of radioactive materials in gaseous effluents will be kept "as low as is reasonably achievable." This control implements the requirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50, and the design objectives given in Section II.D of Appendix I to 10 CFR Part 50. The specified limits governing the use of appropriate portions of the systems were specified as a suitable fraction of the guide set forth in Sections II.B and II.C of Appendix 1, 10 CFR Part 50, for gaseous effluents.

CY-TM-1 70-300 Revision 3 Page 40 of 209 2.2.2.5 Explosive Gas Mixture CONTROL The concentration of oxygen in the Waste Gas Holdup System shall be limited to less than or equal to 2% by volume whenever the concentration of hydrogen in the Waste Gas Holdup System is greater than or equal to 4% by volume.AVAILABILITY:

At all times ACTION: Whenever the concentration of hydrogen in the Waste Gas Holdup System is greater than or equal to 4% by volume, and: a. The concentration of oxygen in the Waste Gas Holdup System is greater than 2% by volume, but less than 4% by volume, without delay, begin to reduce the oxygen concentration to within its limit.b. The concentration of oxygen in the Waste Gas Holdup System is greater than or equal to 4% by volume, immediately suspend additions of waste gas to the Waste Gas Holdup System and without delay, begin to reduce the oxygen concentration to within its limit.BASES: Based on experimental data (Reference 1), lower limits of flammability for hydrogen is 5% and for oxygen is 5% by volume. Therefore, if the concentration of either gas is kept below it lower limit, the other gas may be present in higher amounts without the danger of an explosive mixture.Maintaining the concentrations of hydrogen and oxygen such that an explosive mixture does not occur in the waste gas holdup system provides assurance that the release of radioactive materials will be controlled in conformance with the requirements of General Design Criterion 60 of Appendix A to 10 CFR 50.REFERENCES (1) Bulletin 503, Bureau of Mines; Limits of Flammability of Gases and Vapors CY-TM-1 70-300 Revision 3 Page 41 of 209 2.2.2.6 Waste Gas Decay Tanks CONTROL: The quantity of radioactivity contained in each waste gas decay tank shall be limited to less than or equal to 8800 curies noble gases (considered as Xe-1 33).APPLICABILITY:

At all times ACTION: a. With the quantity of radioactive material in any waste gas decay tank exceeding the above limit, immediately suspend all additions of radioactive material to the tank and within 48 hours5.555556e-4 days <br />0.0133 hours <br />7.936508e-5 weeks <br />1.8264e-5 months <br /> reduce the tank contents to within the limit.BASES Restricting the quantity of radioactivity contained in each waste gas decay tank provides assurance that in the event of an uncontrolled release of the tanks contents, the resulting total body exposure to a MEMBER OF THE PUBLIC at the nearest exclusion area boundary will not exceed 0.5 rem.This is consistent with Standard Review Plan 15.7.1, "Waste Gas System Failure." 2.2.3 Total Radioactive Effluent Controls 2.2.3.1 Total Dose CONTROL: The annual (calendar year) dose or dose commitment to any MEMBER OF THE PUBLIC, due.to releases of radioactivity and to radiation from uranium fuel cycle sources shall be limited to less than or equal to 25 mrem to the total body or any organ except the thyroid, which shall be limited to less than or equal to 75 mrem.APPLICABILITY:

At all times ACTION: With the calculated dose from the release of radioactive materials in liquid or gaseous effluents exceeding twice the limits of Controls 2.2.1.2.a, 2.2.1.2.b, 2.2.2.2.a, 2.2.2.2.b, 2.2.2.3.a, or, 2.2.2.3.b, calculations should be made including CY-TM-1 70-300 Revision 3 Page 42 of 209 direct radiation contributions from the unit and from outside storage tanks to determine whether the above limits of Control 2.2.3.1 have been exceeded.

If such is the case, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which defines the corrective action to be taken to reduce subsequent releases to prevent recurrence of exceeding the above limits and includes the schedule for achieving conformance with the above limits. This Special Report, as defined in 10 CFR Part 20.2203(b), shall include an analysis which estimates the radiation exposure (dose) to a MEMBER OF THE PUBLIC from uranium fuel cycle sources, including all effluent pathways and direct radiation, for the calendar year that includes the release(s) covered by this report. It shall also describe levels of radiation and concentrations of radioactive material involved, and the cause of the exposure levels or concentrations.

If the estimated dose(s) exceed the above limits, and if the release condition resulting in violation of 40 CFR 190 has not already been corrected, the Special Report shall include a request for a variance in accordance with the provisions of 40 CFR 190.Submittal of the report is considered a timely request, and a variance is granted until staff action on the request is complete.BASES This control is provided to meet the dose limitations of 40 CFR Part 190 that have been incorporated into 10 CFR Part 20.1301(d).

This control requires the preparation and submittal of a Special Report whenever the calculated doses from plant generated radioactive effluents and direct radiation exceed 25 mrem to the total body or any organ, except the thyroid, which shall be limited to less than or equal to 75 mrem. For sites containing up to 4 reactors, it is highly unlikely that the resultant dose to a MEMBER OF THE PUBLIC will exceed the dose limits of 40 CFR Part 190 if the individual reactors remain within twice the dose design objectives of Appendix I, and if direct radiation doses from the reactor units and outside storage tanks are kept small. The Special Report will describe a course of action that should result in the limitation of the annual dose to a MEMBER OF THE PUBLIC to within the 40 CFR Part 190 limits. For the purposes of the Special Report, it may be assumed that the dose commitment to the member of the public from other uranium fuel cycle sources is negligible, with the exception that dose contributions from other nuclear fuel cycle facilities at the same site or within a radius of 8 km must be CY-TM-170-300 Revision 3 Page 43 of 209 considered.

If the dose to any member of the public is estimated to exceed the requirements of 40 CFR Part 190, the Special Report with a request for a variance (provided the release conditions resulting in violation of 40 CFR Part 190 have not already been corrected) in accordance with the provisions of 40 CFR Part 190.11 and 10 CFR Part 20.2203(b), is considered to be a timely request and fulfills the requirements of 40 CFR Part 190 until NRC staff action is completed.

The variance only relates to the limits of 40 CFR Part 190, and does not apply in any way to the other requirements for dose limitation of 10 CFR Part 20, as addressed in Controls 2.2.1.1 and 2.2.2.1. An individual is not considered a MEMBER OF THE PUBLIC during any period in which he/she is engaged in carrying out any operation that is part of the nuclear fuel cycle.

CY-TM-1 70-300 Revision 3 Page 44 of 209 3.0 SURVEILLANCES 3.1 Radioactive Effluent Instrumentation 3.1.1 Radioactive Liquid Effluent Instrumentation Surveillance Requirements 3.1.1.1 Each radioactive liquid effluent monitoring instrumentation channel shall be demonstrated OPERABLE by performance of the CHANNEL CHECK, SOURCE CHECK, CHANNEL CALIBRATION, AND CHANNEL TEST operations during the MODES and at the frequencies shown in Table 3.1-1.

CY-TM-1 70-300 Revision 3 Page 45 of 209 Table 3.1-1 Radioactive Liquid Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL INSTRUMENT CHECK CHECK CALIBRATION

1. Radioactivity Monitors Providing Alarm and Automatic Isolation a. Unit 1 Liquid Radwaste Effluents Line (RM-L-6)b. IWTS/IWFS Discharge Line (RM-L-12)2. Flow Rate Monitors a. Unit 1 Liquid Radwaste Effluent Line (WDL-FT-84)
b. Station Effluent Discharge (SR-FT-146)

D D D(3)D(3)P P N/A N/A R(2)R(2)R R CHANNEL TEST Q(1)Q(1)Q Q CY-TM-1 70-300 Revision 3 Page 46 of 209 Table 3.1-1 (Cont'd)Table Notation (1) The CHANNEL TEST shall also demonstrate that automatic isolation of this pathway and control room alarm annunciation occurs if the following condition exists: 1. Instrument indicates measured levels above the high alarm/trip setpoint.(Includes

-circuit failure)2. Instrument indicates a down scale failure. (Alarm function only.) (Includes

-circuit failure)3. Instrument controls moved from the operate mode (Alarm function only).(2) The initial CHANNEL CALIBRATION for radioactivity measurement instrumentation shall be performed using one or more of the reference standards certified by the National Institute of Standards and Technology or using standards that have been obtained from suppliers that participated in measurement assurance activities with NIST. These standards should permit calibrating the system over its intended range of energy and measurement range. For subsequent CHANNEL CALIBRATION, sources that have been related to the initial calibration should be used. (Operating plants may substitute previously established calibration procedures for this requirement)

(3) CHANNEL CHECK shall consist of verifying indication of flow during periods of release.CHANNEL CHECK shall be made at least once daily on any day on which continuous, periodic, or batch releases are made.

CY-TM-170-300 Revision 3 Page 47 of 209 3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements 3.1.2.1 Each radioactive gaseous process or effluent monitoring instrumentation channel shall be demonstrated OPERABLE by performance of the CHANNEL CHECK, SOURCE CHECK, CHANNEL CALIBRATION, and CHANNEL TEST operations at the frequencies shown in Table 3.1-2.

CY-TM-1 70-300 Revision 3 Page 48 of 209 Table 3.1-2 Radioactive Gaseous Process and Effluent Monitorinq Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNEL INSTRUMENT CHECK CHECK CALIBRATION TEST APPLICABILITY

1. Waste Gas Holdup System a. Noble Gas Activity Monitor (RM-A7) P P E(3) Q(1)b. Effluent System Flow Rate Measuring Device (WDG-FT-123)

P N/A E Q 2. Waste Gas Holdup System Explosive Gas Monitoring System a. Hydrogen Monitor (CA-G-1A/B)

D N/A Q(4) M **b. Oxygen Monitor (CA-G-1A/B)

D N/A Q(5) M **3. Containment Purge Vent System a. Noble Gas Activity Monitor (RM-A9) D P E(3) M(1) #b. Iodine Sampler (RM-A9) W N/A N/A N/A #c. Particulate Sampler (RM-A9) W N/A N/A N/A #d. Effluent System Flow Rate Measuring Device (AH-FR-148)

D N/A E Q #e. Sampler Flow Rate Monitor (RM-FI-1231)

D N/A E N/A #4. Condenser Vent System a. Noble Gas Activity Monitor (RM-A5 and Suitable Equivalent

-D M E(3) Q(2)See Table 2.1-2, Item 4.a)

CY-TM-1 70-300 Revision 3 Page 49 of 209 Table 3.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNEL INSTRUMENT

5. Auxiliary and Fuel Handling Building Ventilation System a. Noble Gas Activity Monitor (RM-A8) or (RM-A4 and RM-A6)b. Iodine Sampler (RM-A8) or (RM-A4 and RM-A6)c. Particulate Sampler (RM-A8) or (RM-A4 and RM-A6)d. System Effluent Flow Rate Measurement Devices (AH-FR-149 and AH-FR-1 50)e. Sampler Flow Rate Monitor (RM-FI-1230 or RM-A-4\FI and RM-A-6\FI)
6. Fuel Handling Building ESF Air Treatment System a. Noble Gas Activity Monitor (RM-A14)b. System Effluent Flow Rate (AH-UR-1104 A/B)c. Sampler Flow Rate Measurement Device (RM-A-14FI14)

CHECK CHECK CALIBRATION TEST D W W D D D D D M N/A N/A N/A N/A M N/A N/A E(3)N/A N/A E E R(3)R R Q(1)N/A N/A Q N/A APPLICABILITY Q(2)Q Q CY-TM-1 70-300 Revision 3 Page 50 of 209 Table 3.1-2 (Cont'd)Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL SOURCE CHANNEL CHANNEL INSTRUMENT

7. Chemical Cleaning Building Ventilation System a. Noble Gas Activity Monitor (ALC RM-1-18)b. Iodine Sampler (ALC RM-1-18)c. Particulate Sampler (ALC RM-1-18)8. Waste Handling and Packaging Facility Ventilation System a. Particulate Sampler (WHP-RIT-1)
9. Respirator and Laundry Maintenance Ventilation System a. Particulate Sampler (RLM-RM-1)

CHECK CHECK CALIBRATION TEST Al PPLICABILITY D W W D M N/A N/A W E(3)N/A N/A SA Q(2)N/A N/A W D W SA W CY-TM-170-300 Revision 3 Page 51 of 209 Table 3.1-2 (Cont'd)Table Notation* At all times** During waste gas holdup system operation Operability is not required when discharges are positively controlled through the closure of WDG-V-47, or where RM-A-8, AH-FT-149, and AH-FT-150 are operable and RM-A-8 is capable of automatic closure of WDG-V-47 During Fuel Handling Building ESF Air Treatment System Operation# At all times during containment purging## At all times when condenser vacuum is established

      1. During operation of the ventilation system (1) The CHANNEL TEST shall also demonstrate that automatic isolation of this pathway for the Auxiliary and Fuel Handling Building Ventilation System, the supply ventilation is isolated and control room alarm annunciation occurs if the following condition exists: 1. Instrument indicates measured levels above the high alarm/trip setpoint (Includes circuit failure).2. Instrument indicates a down scale failure (Alarm function only) (Includes circuit failure).3. Instrument controls moved from the operate mode (Alarm function only).(2) The CHANNEL TEST shall also demonstrate that control room alarm annunciation occurs if any of the following conditions exist: 1 Instrument indicates measured levels above the alarm setpoint. (includes circuit failure)2. Instrument indicates a down scale failure (includes circuit failure).3. Instrument controls moved from the operate mode.

CY-TM-170-300 Revision 3 Page 52 of 209 Table 3.1-2 NOTATIONS (Cont'd)(3) The initial CHANNEL CALIBRATION for radioactivity measurement instrumentation shall be performed using one or more of the reference standards certified by the National Institute of Standards and Technology or using standards that have been obtained from suppliers that participate in measurement assurance activities with NIST.These standards should permit calibrating the system over its intended range of energy and measurement range. For subsequent CHANNEL CALIBRATION, sources that have been related to the initial calibration should be used. (Operating plants may substitute previously established calibration procedures for this requirement.)

(4) The CHANNEL CALIBRATION shall include the use of standard gas samples containing a nominal: 1. One volume percent hydrogen, balance nitrogen, and 2. Four volume percent hydrogen, balance nitrogen (5) The CHANNEL CALIBRATION shall include the use of standard gas samples containing a nominal: 1. One volume percent oxygen, balance nitrogen, and 2. Four volume percent oxygen, balance nitrogen CY-TM-170-300 Revision 3 Page 53 of 209 3.2 Radiological Effluents 3.2.1 Liquid Effluents SURVEILLANCE REQUIREMENTS 3.2.1.1 Concentration 3.2.1.1.1 The radioactivity content of each batch of radioactive liquid waste shall be determined prior to release, by sampling and analysis in accordance with Table 3.2-1. The results of pre-release analyses shall be used with the calculational methods in the ODCM to assure that the concentration at the point of release is maintained within the limits of Control 2.2.1.1.3.2.1.1.2 Post-release analysis of samples composited from batch releases shall be performed in accordance with Table 3.2-1. The results of the previous post-release analysis shall be used with the calculational methods in the ODCM to assure that the concentrations at the point of release were maintained within the limits of Control 2.2.1.1.3.2.1.1.3 The radioactivity concentration of liquids discharged from continuous release points shall be determined by collection and analysis of samples in accordance with Table 3.2-1. The results of the analysis shall be used with the calculational methods of the ODCM to assure that the concentration at the point of release is maintained within the limits of Control 2.2.1.1.3.2.1.2 Dose Calculations 3.2.1.2.1 Cumulative dose contributions from liquid effluents shall be determined in accordance with the Offsite Dose Calculation Manual (ODCM) at least once a month.3.2.1.3 Liquid Waste Treatment 3.2.1.3.1 Doses due to liquid releases shall be projected at least once a month, in accordance with the ODCM.

CY-TM-170-300 Revision 3 Page 54 of 209 3.2.1.4 Liquid Holdup Tanks 3.2.1.4.1 The quantity of radioactive material contained in each of the tanks specified in Control 2.2.1.4 shall be determined to be within the limit by analyzing a representative sample of the tank's content weekly when radioactive materials are being added to the tank.

CY-TM-170-300 Revision 3 Page 55 of 209 Liquid Release Type A.1 Batch Waste Release Tanks (Note Table 3.2-1 Radioactive Liquid Waste Sampling and Analysis Program Sampling Minimum Analysis Frequency Frequency Type of Acti d) P P H Each Batch Each Batch Principal GammE II-1 Dissolved and F (Gamma Emi P M Gross Each Batch Composite (Note b)P Q Sr-89 Ii Each Batch Composite (Note b) Fe Continuous W Principal Gamma (Note c) Composite (Note c) I1 Grab Sample M Dissolved and Er M (Gamma Emitter Continuous M H (Note c) Composite (Note c) Gross Continuous Q Sr-89 (Note c) Composite (Note c' Fe A.2 Continuous Releases (Note e)ivity Analysis-3 Emitters (Note f)131 Entrained Gases tters) (Note g)alpha Sr-90-55 Emitters (Note f)31Gases;) (Note g)-3 alpha Sr-90-55 I Lower Limit of Detection (LLD)(p.Ci/ml) (Note a)1 xl0-5 5 x 10-7 1 x 106 1 xl0s 1 x10-7 5 x 10-8 1 x 106 5 X10-7 I x 10 1 x 10-5 1 x 10-1 x l0i 7 5 x 108 1 x 106.1-I..... r. ..... \ ......

  • CY-TM-170-300 Revision 3 Page 56 of 209 Table 3.2-1 (Cont'd)Table Notation a. The LLD is defined, for purposes of this surveillance, as the smallest concentration of radioactive material in a sample that will yield a net count above system background that will be detected with 95% probability with 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):

4.66 Sb LLD =E x V x 2.22 x 106 x Y x exp (-AAt)Where: LLD is the "a priori" lower limit of detection as defined above (as microcurie per unit mass or volume)Sb is the standard deviation of the background counting rate or of the counting rate of a blank sample as appropriate (as counts per minute)E is the counting efficiency (as counts per disintegration)

V is the sample size (in units of mass or volume)2.22 E6 is the number of disintegrations per minute per microcurie Y is the fractional radiochemical yield (when applicable)

X is the radioactive decay constant for the particular radionuclide, and At is the elapsed time between midpoint of sample collection and time of counting Typical values of E, V, Y and At shall be used in the calculation It should be recognized that the LLD is defined as an "a priori" (before the fact)limit representing the capability of a measurement system and not as an "a posteriori" (after the fact) limit for a particular measurement

b. A composite sample is one in which the quantity of liquid sampled is proportional to the quantity of liquid waste discharged and in which the method of sampling employed results in a specimen which is representative of the liquids released CY-TM-1 70-300 Revision 3 Page 57 of 209 Table 3.2-1 Notations (Cont'd)c. To be representative of the quantities and concentrations of radioactive materials in liquid effluent, samples shall be collected continuously in proportion to the rate of flow of the effluent stream. Prior to analyses, all samples taken for the composite shall be thoroughly mixed in order for the composite sample to be representative of the effluent release d. A batch release is the discharge of liquid wastes of a discrete volume. Prior to sampling for analyses, each batch shall be isolated, and be thoroughly mixed, by a method described in the ODCM, to assure representative sampling.e. A continuous release is the discharge of liquid wastes of a non- discrete volume;e.g., from a volume or system that has an input flow during the continuous release.f. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:

Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99, Cs-134, Cs-137, Ce-141, and Ce-144. This list does not mean that only these nuclides are to be considered.

Other gamma peaks that are identifiable, together with those of the above nuclides, shall also be analyzed and reported in the Annual Radioactive Effluent Release Report pursuant to TS 6.9.4.g. The gamma emitters for which the LLD specification applies exclusively are the following radionuclides:

Kr-87, Kr-88, Xe-133, Xe-133m, and Xe-135. This list does not mean that only these nuclides are to be considered.

Other gamma peaks that are identifiable, together with those of the above nuclides, shall also be analyzed and reported in the Annual Effluent Release Report pursuant to T.S.6.9.4.

CY-TM-1 70-300 Revision 3 Page 58 of 209 3.2.2 Gaseous Effluents SURVEILLANCE REQUIREMENTS 3.2.2.1 Dose Rates 3.2.2.1.1 The dose rate due to noble gases in gaseous effluents shall be determined to be within the limits of Control 2.2.2.1 .a in accordance with the methods and procedures of the ODCM.3.2.2.1.2 The dose rate of radioactive materials, other than noble gases, in gaseous effluents shall be determined to be within the limits of Control 2.2.2.1.b in accordance with methods and procedures of the ODCM by obtaining representative samples and performing analyses in accordance with the sampling and analysis program, specified in Table 3.2-2.3.2.2.2 Dose, Noble Gas 3.2.2.2.1 Cumulative dose contributions from noble gas effluents for the current calendar quarter and current calendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM) monthly.3.2.2.3 Dose, Iodine-131, Iodine-1 33, Tritium, and Radionuclides in Particulate Form 3.2.2.3.1 Cumulative dose contributions from Iodine-1 31, Iodine-133, Tritium, and radionuclides in particulate form with half lives greater than 8 days for the current calendar quarter and current calendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM)monthly.3.2.2.4 Gaseous Waste Treatment 3.2.2.4.1 Doses due to gaseous releases from the unit shall be projected monthly in accordance with the ODCM.

CY-TM-170-300 Revision 3 Page 59 of 209 3.2.2.5 Explosive Gas Mixture 3.2.2.5.1 The concentrations of hydrogen and oxygen in the waste gas holdup system shall be determined to be within the limits of Control 2.2.2.5 by monitoring the waste gases in the Waste Gas Holdup System with the hydrogen and oxygen monitors covered in Table 2.1-2 of Control 2.1.2.3.2.2.6 Waste Gas Decay Tank 3.2.2.6.1 The concentration of radioactivity contained in the vent header shall be determined weekly. If the concentration of the vent header exceeds 10.7 gCi/cc, daily samples shall be taken of each waste gas decay tank being added to, to determine if the tank(s) is less than or equal to 8800 Ci/tank.

CY-TM-170-300 Revision 3 Page 60 of 209 Table 3.2-2 Radioactive Gaseous Waste Sampling and Analysis Program Minimum Lower Limit of Sampling Analysis Type of Activity Detection (LLD)Gaseous Release Type Frequency Frequency Analysis piCi/ml) (Note a)P EhaP Principal Gamma 1 A. Waste Gas Decay Tank Grab Sample Each Tank Emitters (Note g)B. Containment Purge H-3 1 x 10-6 P (Note b)Each P (Note b) Each Principal Gamma Purge Grab Sample Purge Emitters (Note g) 1 X 10.C. Auxiliary and Fuel Handling Building H-3 1 x10.6 Air Treatment System M (Notes c, e) Grab Sample M Principal Gamma 1 Emitters (Note g) 1 x 10 D. Fuel Handling Building ESF Air Treatment System M (during System M (during H-3 1 x 10-6 Operation)

System Principal Gamma Grab Sample Operation)

Emitters (Note g) 1 x 10-4 Ex as Nt )H-3 1 x10-6 E. Condenser Vacuum Pumps Exhaust (Note h) M (Note h) M Principal Gamma Grab Sample (Note h) Emitters (Note g) 1 x 10-4 F. Chemical Cleaning Building Air Treatment System MH-3 1 x 1r0i M (Notel1) M Principal Gamma Grab Sample Emitters (Note g) 1x 10-4 G. Waste Handling and Packaging Facility See Section I See Section I See Section I See Section I Air Treatment System of this table of this table of this table of this table H. Respirator and Laundry Maintenance Facility See Section I See Section I See Section I See Section I Air Treatment System of this table of this table of this table , of this table CY-TM-170-300 Revision 3 Page 61 of 209 Table 3.2-2 (Cont'd)Radioactive Gaseous Waste Sampling and Analysis Program Lower Limit of I Sampling Minimum Analysis Type of Activity Detection (LLD)Gaseous Release Type Frequency Frequency Analysis (pCi/ml) (Note a)All Release Types as Listed Above in B, C, D, F, G, and H (During System Operation)

Continuous W (Note d) 1-131 1 X 10-12 (Note f) Charcoal Sample : 1 0 (Note i) ___Principal Gamma Continuous W (Note d) Emitters (Note g) 1x10 1 1 (Note f) Particulate (1-131, Others)Q Continuous Composite Gross Alpha 1 x .10"11 (Note f) Particulate Sample Q Continuous Composite Sr-89, Sr-90 1 x 10-11 (Note f) Particulate Sample Continuous Noble Gas 1 X, (Note f) Beta or Gamma Noble Gases , 1 x 10.6 J, Condenser Vent Stack Continuous Iodine Continuous W (Note d) 1-131 1 x 10-12 Sampler (Note j) (Note k) Charcoal Sample CY-TM-1 70-300 Revision 3 Page 62 of 209 Table 3.2-2 (Cont'd)Table Notation a. The LLD is defined, for purposes of this surveillance, as the smallest concentration of radioactive material in a sample that will yield a net count above system background that will be detected with 95% probability with 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):

4.66Sb LLD =E xV x2.22 x 106 x Y xexp(-kAt)

Where: LLD is the "a priori" lower limit of detection as defined above (as microcurie per unit mass or volume)Sb is the standard deviation of the background counting rate or of the counting rate of a blank sample as appropriate (as counts per minute)E is the counting efficiency (as counts per disintegration)

V is the sample size (in units of mass or volume)2.22 E6 is the number of disintegrations per minute per microcurie Y is the fractional radiochemical yield (when applicable)

X is the radioactive decay constant for the particular radionuclide, and At is the elapsed time between midpoint of sample collection and time of counting.Typical values of E, V, Y and At shall be used in the calculation.

It should be recognized that the LLD is defined as an "a priori" (before the fact)limit representing the capability of a measurement system and not as an "a posteriori" (after the fact) limit for a particular measurement.

b. Sampling and analysis shall also be performed following shutdown, startup, or THERMAL POWER change exceeding 15 percent of RATED THERMAL POWER within one hour, unless (1) analysis shows that the DOSE EQUIVALENT 1-131 concentration in the primary coolant has not increased more than a factor of 3; and (2) the noble gas activity monitor shows that effluent activity has not increased by more than a factor of 3.c. Tritium grab samples from the spent fuel pool area shall be taken at least once per 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> when the refueling canal is flooded.

CY-TM-170-300 Revision 3 Page 63 of 209 Table 3.2-2 Notations (Cont'd)d. Charcoal cartridges and particulate filters shall be changed at least once per 7 days and analyses shall be completed within 48 hours5.555556e-4 days <br />0.0133 hours <br />7.936508e-5 weeks <br />1.8264e-5 months <br /> after changing (or after removal from sampler).e. Tritium grab samples shall be taken weekly from the spent fuel pool area whenever spent fuel is in the spent fuel pool.f. The ratio of the sample flow rate to the sampled stream flow rate shall be known for the time period covered by each dose or dose rate calculation made in accordance with Controls 2.2.2.1, 2.2.2.2, and 2.2.2.3.g. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:

Kr-87, Kr-88, Xe-1 33, Xe-1 33m, Xe-1 35 and Xe-1 38 for gaseous emissions and Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99, Cs-1 37, Ce-141 and Ce-144 for particulate emissions.

This list does not mean that only these nuclides are to be considered.

Other gamma peaks that are identifiable, together with those of the above nuclides, shall also be analyzed and reported in the Annual Radioactive Effluent Release Report pursuant to TS 6.9.4.h. Applicable only when condenser vacuum is established.

Sampling and analysis shall also be performed following shutdown, startup, or a THERMAL POWER change exceeding 15 percent of RATED THERMAL POWER within one hour unless (1) analysis shows that the DOSE EQUIVALENT 1-131 concentration in the primary coolant has not increased more than a factor of 3; and (2) the noble gas activity monitor shows that effluent activity has not increased by more than a factor of 3.Gross Alpha, Sr-89, and Sr-90 analyses do not apply to the Fuel Handling Building ESF Air Treatment System.j. If the Condenser Vent Stack Continuous Iodine Sampler is unavailable, then alternate sampling equipment will be placed in service within 48 hours5.555556e-4 days <br />0.0133 hours <br />7.936508e-5 weeks <br />1.8264e-5 months <br /> or a report will be prepared, and submitted within 30 days from the time the sampler is found or made inoperable, which identifies (a) the cause of the inoperability, (b) the action taken to restore representative sampling capability, (c) the action taken to prevent recurrence, and (d) quantification of the release via the pathway during the period and comparison to the limits prescribed by Control 2.2.2.1.b.

k. Applicable only when condenser vacuum is established.
1. Applicable when liquid radwaste is moved or processed within the facility.m. Iodine samples only required in the Chemical Cleaning Building when TMI-1 liquid radwaste is stored or processed in the facility.

CY-TM-1 70-300 Revision 3 Page 64 of 209 3.2.3 Total Radioactive Effluents 3.2.3.1 Dose Calculation 3.2.3.1.1 Cumulative annual dose contributions from liquid and gaseous effluents shall be determined in accordance with Surveillances 3.2.1.2.1, 3.2.2.2.1, and 3.2.2.3.1, including direct radiation contributions from the Unit and from outside storage tanks, and in accordance with the methodology contained in the ODCM.

CY-TM-170-300 Revision 3 Page 65 of 209 4.0 PART I REFERENCES 4.1 Title 10, Code of Federal Regulations, "Energy" 4.2 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routing Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I, "Revision 1, October 1977 4.3 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-50 4.4 TMI-1 FSAR CY-TM-1 70-300 Revision 3 Page 66 of 209 PART II TMI-2 RADIOLOGICAL EFFLUENT CONTROLS CY-TM-1 70-300 Revision 3 Page 67 of 209 PART II Definitions

1.0 DEFINITIONS

DEFINED TERMS 1.1 The DEFINED TERMS of this section appear in capitalized type and are applicable throughout Part II of the ODCM.PDMS 1.2 Post-Defueling Monitored Storage (PDMS) is that condition where TMI-2 defueling has been completed, the core debris removed from the reactor during the clean-up period has been shipped off-site, and the facility has been placed in a stable, safe, and secure condition.

ACTION 1.3 ACTION shall be those additional requirements specified as corollary statements to each control and shall be part of the controls.OPERABLE -OPERABILITY 1.4 A system, subsystem, train, component or device shall be OPERABLE or have OPERABILITY when it is capable of performing its specified function(s).

Implicit in this definition shall be the assumption that all necessary attendant instrumentation, controls, normal and emergency electrical power sources, cooling or seal water, lubrication or other auxiliary equipment, that are required for the system, subsystem, train, component or device to perform its function(s), are also capable of performing their related support function(s).

CHANNEL CALIBRATION 1.5 A CHANNEL CALIBRATION shall be the adjustment, as necessary, of the channel output such that it responds with necessary range and accuracy to known values of the parameter, which the channel monitors.

The CHANNEL CALIBRATION shall encompass the entire channel including the sensor and alarm and/or trip functions, and shall include the CHANNEL FUNCTIONAL TEST. CHANNEL CALIBRATION may be performed by any series of sequential, overlapping or total channel steps such that the entire channel is calibrated.

CY-TM-1 70-300 Revision 3 Page 68 of 209 CHANNEL CHECK 1.6 A CHANNEL CHECK shall be the qualitative assessment of channel behavior during operation by observation.

This determination shall include, where possible, comparison of the channel indication and/or status with other indications and/or status derived from independent instrument channels measuring the same parameter.

CHANNEL FUNCTIONAL TEST 1.7 A CHANNEL FUNCTIONAL TEST shall be: a. Analog channels -the injection of a simulated signal into the channel as close to the primary sensor as practicable to verify OPERABILITY including alarm and/or trip functions.

b. Bistable channels -the injection of a simulated signal into the channel sensor to verify OPERABILITY including alarm and/or trip functions.

SOURCE CHECK 1.8 A SOURCE CHECK shall be the qualitative assessment of channel response when the channel sensor is exposed to a radioactive source.COMPOSITE SAMPLE 1.9 A COMPOSITE SAMPLE is a combination of individual samples obtained at regular intervals over a time period. Either the volume of each individual sample is proportional to the flow rate discharge at the time of sampling or the number of equal volume samples is proportional to the time period used to produce the composite.

GRAB SAMPLE 1.10 A GRAB SAMPLE is an individual sample collected in less than fifteen minutes.BATCH RELEASE 1.11 A BATCH RELEASE is the discharge of fluid waste of a discrete volume.CONTINUOUS RELEASE 1.12 A CONTINUOUS RELEASE is the discharge of fluid waste of a non-discrete volume, e.g., from a volume or system that has an input flow during the CONTINUOUS RELEASE.

CY-TM-170-300 Revision 3 Page 69 of 209 SITE BOUNDARY 1.13 The SITE BOUNDARY used as the basis for the limits on the release of gaseous effluents is as defined in Section 2.1.2.2 and shown on Figure 2.1-3 of the TMI-1 FSAR. This boundary line includes portions of the Susquehanna River surface between the east bank of the river and Three Mile Island and between Three Mile Island and Shelley Island.The SITE BOUNDARY used as the basis for the limits on the release of liquid effluents is as shown in Figure 1.1 in Part I of this ODCM.FREQUENCY NOTATION 1.14 The FREQUENCY NOTATION specified for the performance of Surveillance Requirements shall correspond to the intervals defined in Table 1.1. All Surveillance Requirements shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% of the surveillance interval.

CY-TM-170-300 Revision 3 Page 70 of 209 TABLE 1.1 Frequency Notation NOTATION FREQUENCY S (Shiftly)D (Daily)W (Weekly)M (Monthly)Q (Quarterly)

SA (Semi-Annually)

A (Annually)

E N.A.At least once per 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> At least once per 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> At least once per 7 days At least once per 31 days At least once per 92 days At least once per 184 days At least once per 12 months At least once per 18 months Not applicable Completed prior to each release P CY-TM-170-300 Revision 3 Page 71 of 209 2.0 CONTROLS AND BASES 2.0.1 Controls and ACTION requirements shall be applicable during the conditions specified for each control.2.0.2 Adherence to the requirements of the Control and/or associated ACTION within the specified time interval shall constitute compliance with the control. In the event the Control is restored prior to expiration to the specified time interval, completion of the ACTION statement is not required.2.0.3 In the event the Control and associated ACTION requirements cannot be satisfied because of circumstances in excess of those addressed in the Control, initiate appropriate actions to rectify the problem to the extent possible under the circumstances, and submit a special report to the Commission pursuant to TMI-2 PDMS Technical Specification (Tech.Spec.) Section 6.8.2 within 30 days, unless otherwise specified.

2.1 Radioactive Effluent Instrumentation 2.1.1 Radioactive Liquid Effluent Instrumentation Radioactive Liquid Effluent Instrumentation is common between TMI-1 and TMI-2. Controls, applicability, and actions are specified in ODCM Part I, Control 2.1.1 2.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation CONTROL: The radioactive gaseous process and effluent monitoring instrumentation channels shown in Table 2.1-2 shall be OPERABLE with their alarm/trip setpoints set to ensure that the limits of Control 2.2.2.1 are not exceeded.

The alarm/trip setpoints of these channels shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM).APPLICABILITY:

As shown in Table 2.1-2 ACTION: a. With a radioactive gaseous process or effluent monitoring instrumentation channel alarm/trip setpoint less conservative than required by the above control, immediately suspend the release of radioactive effluent monitored by the affected channel or declare the channel inoperable.

CY-TM-1 70-300 Revision 3 Page 72 of 209 b. With less than the minimum number of radioactive gaseous process or effluent monitoring instrumentation channels OPERABLE, take the ACTION shown in Table 2.1-2. Exert best efforts to return the instrumentation to OPERABLE status within 30 days and, if unsuccessful, explain in the next Annual Effluent Release Report why the inoperability was not corrected in a timely manner.BASES The radioactive gaseous effluent instrumentation is provided to monitor and control, as applicable, the releases of radioactive materials in gaseous effluent during actual or potential releases.

The alarm/trip setpoints for these instruments shall be calculated in accordance with NRC approved methods in the ODCM to provide reasonable assurance that the annual releases are within the limits specified in 10 CFR 20.1301.

CY-TM-170-300 Revision 3 Page 73 of 209 Table 2.1-2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation MINIMUM CHANNELS INSTRUMENT OPERABLE APPLICABILITY ACTION 1. Containment Purge Monitoring System a. Noble Gas Activity Monitor (2HP-R-225) 1 NOTE 1 NOTE 2 b. Particulate Monitor (2HP-R-225) 1 NOTE 1 NOTE 2 c. Effluent System Flow Rate Measuring Device (2AH-FR-5907 Point 1) 1 NOTE 1 NOTE 3 2. Station Ventilation System a. Noble Gas Activity Monitor (2HP-R-219) or (2HP-R-219A) 1 NOTE 1 NOTE 2 b. Particulate Monitor (2HP-R-219) or (2HP-R-219A) 1 NOTE 1 NOTE 2 c. Effluent System Flow Rate Monitoring Device (2AH-FR-5907 Point 6) 1 NOTE 1 NOTE 3 NOTES: 1. During operation of the monitored system.2. With the number of channels OPERABLE less than required by the Minimum Channels OPERABLE requirement, secure Reactor Building Purge if in progress.3. With flow rate monitoring instrumentation out of service, flow rates from the Auxiliary (2AH-FR-5907 Point 2), Fuel Handling (2AH-FR-5907 Point 4), Soiled Exhaust System (2AH-FR-5907 Point 5), and Reactor Buildings (2AH-FR-5907 Point 1) may be summed individually.

Under these conditions, the flow rate monitoring device is considered operable.

If the flow rates cannot be summed individually, they may be estimated using the maximum design flow for the exhaust fans, and the reporting requirements of Control 2.1.2.b are applicable.

CY-TM-170-300 Revision 3 Page 74 of 209 2.2 Radioactive Effluent Controls 2.2.1 Liquid Effluent Controls 2.2.1.1 Liquid Effluent Concentration CONTROL: The concentration of radioactive material released at anytime from the unit to unrestricted areas shall be limited to ten times the concentrations specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2, Column 2.APPLICABILITY:

At all times ACTION: With the concentration of radioactive material released from the unit to unrestricted areas exceeding the above limits, immediately restore concentrations within the above limits.BASES This control is provided to ensure that the concentration of radioactive materials released in liquid waste effluent from the unit to unrestricted areas will be less than ten times the concentration levels specified in 10 CFR Part 20.1001-20.2401, Appendix B, Table 2. These Controls permit flexibility under unusual conditions, which may temporarily result in higher than normal releases, but still within ten times the concentrations, specified in 10 CFR 20. It is expected that by using this flexibility under unusual conditions, and exerting every effort to keep levels of radioactive material in liquid wastes as low as practicable, the annual releases will not exceed a small fraction of the annual average concentrations specified in 10 CFR 20. As a result, this Control provides reasonable assurance that the resulting annual exposure to an individual in off-site areas will not exceed the design objectives of Section II.A of Appendix I to 10 CFR Part 50, which were established as requirements for the cleanup of TMI-2 in the NRC's Statement of Policy of April 27, 1981.

CY-TM-1 70-300 Revision 3 Page 75 of 209 2.2.1.2 Liquid Effluent Dose CONTROL The dose or dose commitment to a MEMBER OF THE PUBLIC from radioactive materials in liquid effluents released from the unit to the SITE BOUNDARY shall be limited: a. During any calendar quarter to less than or equal to 1.5 mrem to the total body and to less than or equal to 5 mrem to any organ.b. During any calendar year to less than or equal to 3 mrem to the total body and to less than or equal to 10 mrem to any organ.APPLICABILITY:

At all times ACTION: a. With the calculated dose from the release of radioactive materials in liquid effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit(s) and defines the corrective actions to be taken to reduce the releases of radioactive materials in liquid effluents during the remainder of the current calendar quarter and during the subsequent 3 calendar quarters so that the cumulative dose or dose commitment to any individual from such releases during these four calendar quarters is within 3 mrem to the total body and 10 mrem to any organ. This Special Report shall also include (1) the result of radiological analyses of the drinking water source, and (2) the radiological impact on finished drinking water supplies with regard to the requirements of 40 CFR 141, Safe Drinking Water Act.

CY-TM-1 70-300 Revision 3 Page 76 of 209 BASES This Control requires that the dose to offsite personnel be limited to the design objectives of Appendix I of 10 CFR Part 50. This will assure the dose received by the public during PDMS is equivalent to or less than that from a normal operating reactor. The limits also assure that the environmental impacts are consistent with those assessed in NUREG-0683, the TMI-2 Programmatic Environmental Impact Statement (PEIS). The ACTION statements provide the required flexibility under unusual conditions and at the same time implement the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive material in liquid effluents will be kept "as low as is reasonably achievable".

The dose calculations in the ODCM implement the requirements in Section lIlA.. of Appendix I that conformance with the guides of Appendix I is to be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.

The equations specified in the ODCM for calculating the doses due to the actual release rates of radioactive materials in liquid effluents are consistent with the methodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October, 1977, and Regulatory Guide 1.113, "Estimating Aquatic Dispersion of Effluents from Accidental and Routine Reactor Releases for the Purpose of Implementing Appendix I," April, 1977.NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.113.

CY-TM-1 70-300 Revision 3 Page 77 of 209 2.2.1.3 Liquid Radwaste Treatment System CONTROL: The appropriate portions of the liquid radwaste treatment system shall be used to reduce the radioactive materials in liquid wastes prior to their discharge when the projected doses due to the liquid effluent from the unit to unrestricted areas would exceed 0.06 mrem to the total body or 0.2 mrem to any organ in any calendar month.APPLICABILITY:

At all times ACTION: a. With radioactive liquid waste being discharged without treatment and in excess of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which includes the following information:

1. Explanation of why liquid radwaste was being discharged without treatment, identification of any inoperable equipment or subsystems, and the reason for inoperability, 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and, 3. A summary description of action(s) taken to prevent a recurrence.

BASES The requirement that the appropriate portions of this system (shared with TMI-1) be used, when specified, provides assurance that the releases of radioactive materials in liquid effluents will be kept as low as is reasonably achievable.

This control implements the requirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50 and the design objective given in Section II.D of Appendix I to 10 CFR Part 50. The intent of Section ll.D. is to reduce effluents to as low as is reasonably achievable in a cost effective manner. This control satisfies this intent by establishing a dose limit which is a small fraction (25%) of Section II.A of Appendix 1, 10 CFR Part 50 dose requirements.

This margin, a factor of 4, constitutes a reasonable reduction.

CY-TM-1 70-300 Revision 3 Page 78 of 209 2.2.2 Gaseous Effluent Controls 2.2.2.1 Gaseous Effluent Dose Rate CONTROL: The dose rate due to radioactive materials released in gaseous effluent from the site shall be limited to the following:

a. For noble gases: less than or equal to 500 mrem/yr to the total body and less than or equal to 3000 mrem/yr to the skin, and b. For tritium and all radionuclides in particulate form with half lives greater than 8 days: less than or equal to 1500 mrem/yr to any organ.APPLICABILITY:

At all times.ACTION: With the release rate(s) exceeding the above limits, immediately decrease the release rate to comply with the above limit(s).

CY-TM-1 70-300 Revision 3 Page 79 of 209 BASES The control provides reasonable assurance that the annual dose at the SITE BOUNDARY from gaseous effluent from all units on the site will be within the annual dose limits of 10 CFR Part 20 for unrestricted areas. At the same time, these Controls permit flexibility under unusual conditions, which may temporarily result in higher than the design objective levels, but still within the dose limits specified in 10 CFR 20 and within the design objectives of Appendix I to 10 CFR 50. It is expected that using this flexibility under unusual conditions, and by exerting every effort to keep levels of radioactive material in gaseous wastes as low as practicable, the annual releases will not exceed a small fraction of the annual dose limits specified in 10 CFR 20 and will not result in doses which exceed the design objectives of Appendix I to 10 CFR 50, which were endorsed as limits for the cleanup of TMI-2 by the NRC's Statement of Policy of April 27, 1981. These gaseous release rates provide reasonable assurance that radioactive material discharged in gaseous effluent will not result in the exposure of a MEMBER OF THE PUBLIC in an unrestricted area, either within or outside the SITE BOUNDARY, to annual average concentrations exceeding the values specified in Appendix B, Table 2 of 10 CFR Part 20. For MEMBERS OF THE PUBLIC who may at times be within the SITE BOUNDARY, the occupancy of the MEMBER OF THE PUBLIC will be sufficiently low to compensate for any increase in the atmospheric diffusion factor above that for the exclusion area boundary.

The specified release rate limits restrict, at all times, the corresponding gamma and beta dose rates above background to a MEMBER OF THE PUBLIC at or beyond the SITE BOUNDARY to less than or equal to 500 mrem/year to the total body or to less than or equal to 3000 mrem/year to the skin. The absence of iodine ensures that the corresponding thyroid dose rate above background to a child via the inhalation pathway is less than or equal to 1500 mrem/yr (NUREG 1301), thus there is no need to specify dose rate limits for these nuclides.

CY-TM-170-300 Revision 3 Page 80 of 209 2.2.2.2 Gaseous Effluents Dose-Noble Gases CONTROL: The air dose due to noble gases released in gaseous effluents from the unit to areas at and beyond the SITE BOUNDARY shall be limited to the following:

a. During any calendar quarter: less than or equal to 5 mrad for gamma radiation and less than or equal to 10 mrad for beta radiation and, b. During any calendar year: less than or equal to 10 mrad for gamma radiation and less than or equal to 20 mrad for beta radiation.

APPLICABILITY:

At all times.ACTION: a. With the calculated air dose from radioactive noble gases in gaseous effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit(s) and defines the corrective actions that have been taken to reduce the releases and the proposed corrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.BASES This control applies to the release of radioactive materials in gaseous effluents from TMI-2.

CY-TM-1 70-300 Revision 3 Page 81 of 209.This control and associated action is provided to implement the requirements of Section 1I.B, III.A and IV.A of Appendix I, 10 CFR Part 50. The Control implements the guides set forth in Section II.B of Appendix I. The ACTION statements provide flexibility under unusual conditions and at the same time implement the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive material in gaseous effluents will be kept "as low as is reasonably achievable." The Surveillance Requirements implement the requirements in Section III.A of Appendix I that conformance with the guides of Appendix I be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through the appropriate pathways is unlikely to be substantially underestimated.

The dose calculation methodology and parameters established in the ODCM for calculating the doses due to the actual release rates of radioactive noble gases in gaseous effluents are consistent with the methodology provided in Regulatory Guide 1.109,"Calculation of Annual Doses to Man from Routine Release of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977 and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water Cooled Reactors," Revision 1, July 1977. The ODCM equations provided for determining the air doses at and beyond the SITE BOUNDARY are based upon the historical average atmospheric conditions.

NUREG-0133 provides methods for dose calculations consistent with Regulatory Guides 1.109 and 1.111.2.2.2.3 Dose -Iodine-131, Iodine-133, Tritium, and Radionuclides In Particulate Form CONTROL: The dose to a MEMBER OF THE PUBLIC from Tritium and all radionuclides in particulate form with half lives greater than 8 days, in gaseous effluents released from the unit to areas at and beyond the SITE BOUNDARY shall be limited to the following:

a. During any calendar quarter: less than or equal to 7.5 mrem to any organ, and b. During any calendar year: less than or equal to 15 mrem to any organ.

CY-TM-1 70-300 Revision 3 Page 82 of 209 APPLICABILITY:

At all times.ACTION: With the calculated dose from the release of Tritium and radionuclides in particulate form with half lives greater than 8 days, in gaseous effluents exceeding any of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which identifies the cause(s) for exceeding the limit and defines the corrective actions that have been taken to reduce the releases and the proposed corrective actions to be taken to assure that subsequent releases will be in compliance with the above limits.

CY-TM-1 70-300 Revision 3 Page 83 of 209 BASES This control applies to the release of radioactive materials in gaseous effluents from TMI-2.This control and associated action is provided to implement the requirements of Section II.C, III.A and IV.A of Appendix I, 10 CFR Part 50. The Controls are the guides set forth in Section II.C of Appendix I. The ACTION statement provides flexibility during unusual conditions and at the same time implements the guides set forth in Section IV.A of Appendix I to assure that the releases of radioactive materials in gaseous effluents will be kept "as low as is reasonably achievable." The ODCM calculational methods specified in the surveillance requirements implement the requirements in Section III.A of Appendix I that conformance with the guides of Appendix I be shown by calculational procedures based on models and data such that the actual exposure of a MEMBER OF THE PUBLIC through appropriate pathways is unlikely to be substantially underestimated.

The ODCM calculational methodology and parameters for calculating the doses due to the actual release rates of the subject materials are consistent with the methodology provided in Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October, 1977 and Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors," Revision 1, July, 1977. These equations also provide for determining the actual doses based upon the historical average atmospheric conditions.

The release rate controls for iodine-131, iodine-133, tritium and radionuclides in particulate form with half lives greater than 8 days are dependent upon the existing radionuclide pathways to man, in areas at and beyond the SITE BOUNDARY.

The pathways that were examined in the development of these calculations were: 1) individual inhalation of airborne radionuclides, 2) deposition of radionuclides onto green leafy vegetation with subsequent consumption by man, 3) deposition onto grassy areas where milk animals and meat producing animals graze with consumption of the milk and meat by man, and 4) deposition on the ground with subsequent exposure of man. The absence of iodines at the site eliminates the need to specify dose limits for these nuclides.

CY-TM-1 70-300 Revision 3 Page 84 of 209 2.2.2.4 Ventilation Exhaust Treatment System CONTROL The VENTILATION EXHAUST TREATMENT SYSTEM shall be OPERABLE.

The appropriate portions of the VENTILATION EXHAUST TREATMENT SYSTEM shall be used to reduce radioactive materials in gaseous waste prior to their discharge when the monthly projected doses due to gaseous effluent releases from the site would exceed 0.3 mrem to any organ.APPLICABILITY:

At all times.ACTION: a. With the VENTILATION EXHAUST TREATMENT SYSTEM inoperable for more than a month or with gaseous waste being discharged without treatment and in excess of the above limits, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which includes the following information:

1. Identification of the inoperable equipment or subsystems and the reason for inoperability, 2. Action(s) taken to restore the inoperable equipment to OPERABLE status, and 3. A summary description of action(s) taken to prevent a recurrence.

BASES The use of the VENTILATION EXHAUST TREATMENT SYSTEM ensures that gaseous effluents are treated as appropriate prior to release to the environment.

The appropriate portions of this system provide reasonable assurance that the releases of radioactive materials in gaseous effluents will be kept "as low as is reasonably achievable." This control implements the requirements of 10 CFR Part 50.36a, General Design Criterion 60 of Appendix A to 10 CFR Part 50, and the design objectives given in Section II.D of Appendix I to 10 CFR Part 50. The specified limits governing the use of appropriate portions of the systems were CY-TM-170-300 Revision 3 Page 85 of 209 specified as a suitable fraction of the guide set forth in Sections II.B and II.C of Appendix 1, 10 CFR Part 50, for gaseous effluents.

2.2.3 Total Radioactive Effluent Controls 2.2.3.1 Total Dose CONTROL: The annual (calendar year) dose or dose commitment to any MEMBER OF THE PUBLIC, due to releases of radioactivity and to radiation from uranium fuel cycle sources shall be limited to less than or equal to 25 mrem to the total body or any organ except the thyroid, which shall be limited to less than or equal to 75 mrem.APPLICABILITY:

At all times.ACTION: With the calculated dose from the release of radioactive materials in liquid or gaseous effluents exceeding twice the limits of Controls 2.2.1.2.a, 2.2.1.2.b, 2.2.2.2.a, 2.2.2.2.b, 2.2.2.3.a, or, 2.2.2.3.b, calculations should be made including direct radiation contributions from the unit and from outside storage tanks to determine whether the above limits of Control 2.2.3.1 have been exceeded.

If such is the case, prepare and submit to the NRC Region I Administrator within 30 days, a Special Report which defines the corrective action to be taken to reduce subsequent releases to prevent recurrence of exceeding the above limits and includes the schedule for achieving conformance with the above limits. This Special Report, as defined in 10 CFR Part 20.2203(b), shall include an analysis which estimates the radiation exposure (dose) to a MEMBER OF THE PUBLIC from uranium fuel cycle sources, including all effluent pathways and direct radiation, for the calendar year that includes the release(s) covered by this report. It shall also describe levels of radiation and concentrations of radioactive material involved, and the cause of the exposure levels or concentrations.

If the estimated dose(s) exceed the above limits, and if the release condition resulting in violation of 40 CFR 190 has not already been corrected, the Special Report shall include a request for a variance in accordance with the provisions of 40 CFR 190.Submittal of the report is considered a timely request, and a variance is granted until staff action on the request is complete.

CY-TM-1 70-300 Revision 3 Page 86 of 209 BASES This control is provided to meet the dose limitations of 40 CFR Part 190 that have been incorporated into 10 CFR Part 20.1301(d).

This control requires the preparation and submittal of a Special Report whenever the calculated doses from plant generated radioactive effluents and direct radiation exceed 25 mrem to the total body or any organ, except the thyroid, which shall be limited to less than or equal to 75 mrem. For sites containing up to 4 reactors, it is highly unlikely that the resultant dose to a MEMBER OF THE PUBLIC will exceed the dose limits of 40 CFR Part 190 if the individual reactors remain within twice the dose design objectives of Appendix I, and if direct radiation doses from the reactor units and outside storage tanks are kept small. The Special Report will describe a course of action that should result in the limitation of the annual dose to a MEMBER OF THE PUBLIC to within the 40 CFR Part 190 limits. For the purposes of the Special Report, it may be assumed that the dose commitment to the member of the public from other uranium fuel cycle sources is negligible, with the exception that dose contributions from other nuclear fuel cycle facilities at the same site or within a radius of 8 km must be considered.

If the dose to any member of the public is estimated to exceed the requirements of 40 CFR Part 190, the Special Report with a request for a variance (provided the release conditions resulting in violation of 40 CFR Part 190 have not already been corrected), in accordance with the provisions of 40 CFR Part 190.11 and 10 CFR Part 20.2203(b), is considered to be a timely request and fulfills the requirements of 40 CFR Part 190 until NRC staff action is completed.

The variance only relates to the limits of 40 CFR Part 190, and does not apply in any way to the other requirements for dose limitation of 10 CFR Part 20, as addressed in Controls 2.2.1.1 and 2.2.2.1. An individual is not considered a MEMBER OF THE PUBLIC during any period in which he/she is engaged in carrying out any operation that is part of the nuclear fuel cycle.

CY-TM-170-300 Revision 3 Page 87 of 209 3.0 SURVEILLANCES 3.0.1 Surveillance Requirements shall be applicable during the conditions specified for individual Controls unless otherwise stated in an individual Surveillance Requirement.

The Surveillance Requirements shall be performed to demonstrate compliance with the OPERABILITY requirements of the Control.3.0.2 Each Surveillance Requirement shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% of the surveillance interval.3.0.3 Failure to perform a Surveillance Requirement within the time interval specified in Section 3.0.2 shall constitute non-compliance with OPERABILITY requirements for a Control. The time limits of the ACTION requirements are applicable at the time it is identified that a Surveillance Requirement has not been performed.

The ACTION requirements may be delayed for up to 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> to permit completion of the surveillance when the allowable outage time limits of the ACTION requirements are less than 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />. Surveillance Requirements do not have to be performed on inoperable equipment.

3.1 Radioactive Effluent Instrumentation 3.1.1 Radioactive Liquid Effluent Instrumentation SURVEILLANCE REQUIREMENTS 3.1.1.1 Radioactive Liquid Effluent Instrumentation is common between TMI-1 and TMI-2. Surveillances for this instrumentation are specified in ODCM Part I, Surveillance 3.1.1.3.1.2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation SURVEILLANCE REQUIREMENTS 3.1.2.1 Each radioactive gaseous process or effluent monitoring instrumentation channel shall be demonstrated OPERABLE by performance of the CHANNEL CHECK, SOURCE CHECK, CHANNEL CALIBRATION, and CHANNEL TEST operations at the frequencies shown in Table 3.1-2.

CY-TM-1 70-300 Revision 3 Page 88 of 209 Table 3.1-2 Radioactive Gaseous Process and Effluent Monitoring Instrumentation Surveillance Requirements CHANNEL CHECK INSTRUMENT

1. Containment Purge Monitoring System a. Noble Gas Activity Monitor (2HP-R-225)
b. Particulate Sampler (2HP-R-225)

CHANNEL CALIBRATION E N/A CHANNEL FUNCTIONAL TEST M N/A APPLICABILITY NOTE 1 NOTE 1 D w 2. Station Ventilation Monitoring System a. Noble Gas Activity Monitor (2HP-R-219) and (2HP-R-219A)

b. Particulate Sampler (2HP-R-219) and (2HP-R-219A)

NOTES: 1. During operation of the monitored system.D w E N/A M N/A NOTE 1 NOTE 1 CY-TM-170-300 Revision 3 Page 89 of 209 3.2 Radioactive Effluents 3.2.1 Liquid Effluents SURVEILLANCE REQUIREMENTS 3.2.1.1 Concentration 3.2.1.1.1 The radioactivity content of each batch of radioactive liquid waste shall be determined by sampling and analysis in accordance with Table 3.2-1. The results of analyses shall be used with the calculational methods in the ODCM to assure that the concentration at the point of release is maintained within the limits of Control 2.2.1 .1.3.2.1.1.2 Analysis of samples composited from batch releases shall be performed in accordance with Table 3.2-1. The results of the analysis shall be used with the calculational methods in the ODCM to assure that the concentrations at the point of release were maintained within the limits of Control 2.2.1.1.3.2.1.1.3 The radioactivity concentration of liquids discharged from continuous release points shall be determined by collection and analysis of samples in accordance with Table 3.2-1. The results of the analysis shall be used with the calculational methods of the ODCM to assure that the concentration at the point of release is maintained within the limits of Control 2.2.1.1.3.2.1.2 Dose Calculations 3.2.1.2.1 Cumulative dose contributions from liquid effluents shall be determined in accordance with the Offsite Dose Calculation Manual (ODCM) at least once a month.3.2.1.3 Dose Projections 3.2.1.3.1 Doses due to liquid releases shall be projected at least once a month, in accordance with the ODCM.

CY-TM-170-300 Revision 3 Page 90 of 209 TABLE 3.2-1 Radioactive Liquid Waste Sampling and Analysis Program (4, 5)A. Liquid Releases Sampling Frequency Type of Detectable Activity Analysis Concentration (3)P Individual Gamma 5E-7 ýLCi/ml (2)Each Batch H-3 1 E-5 ýtCi/ml Q Gross Alpha 1 E-7 JLCi/ml Quarterly Composite (1) Sr-90 5E-8 jtCi/ml NOTES: (1) A COMPOSITE SAMPLE is one in which the quantity of liquid sampled is proportional to the quantity of liquid waste discharged from the plant.(2) For certain mixtures of gamma emitters, it may not be possible to measure radionuclides in concentrations near this sensitivity limit when other nuclides are present in the sample in much greater concentrations.

Under these circumstances, it will be more appropriate to calculate the concentrations of such radionuclides using measured ratios with those radionuclides, which are routinely identified and measured.(3) The detectability limits for radioactivity analysis are based on the technical feasibility and on the potential significance in the environment of the quantities released.

For some nuclides, lower detection limits may be readily achievable and when nuclides are measured below the stated limits, they should also be reported.(4) The results of these analyses should be used as the basis for recording and reporting the quantities of radioactive material released in liquid effluents during the sampling period. In estimating releases for a period when analyses were not performed, the average of the two adjacent data points spanning this period should be used. Such estimates should be included in the effluent records and reports; however, they should be clearly identified as estimates, and the method used to obtain these data should be described.

(5) Deviations from the sampling/analysis regime will be noted in the report specified in ODCM Part IV.

CY-TM-1 70-300 Revision 3 Page 91 of 209 3.2.2 Gaseous Effluents SURVEILLANCE REQUIREMENTS 3.2.2.1 Dose Rates 3.2.2.1.1 The dose rate due to noble gases in gaseous effluents shall be determined to be within the limits of Control 2.2.2.1 .a in accordance with the methods and procedures of the ODCM.3.2.2.1.2 The dose rate of radioactive materials, other than noble gases, in gaseous effluents shall be determined to be within the limits of Control 2.2.2.1.b in accordance with methods and procedures of the ODCM by obtaining representative samples and performing analyses in accordance with the sampling and analysis program, specified in Table 3.2-2.3.2.2.2 Dose, Noble Gas 3.2.2.2.1 Cumulative dose contributions from noble gas effluents for the current calendar quarter and current calendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM) monthly.3.2.2.3 Dose, Tritium and Radionuclides In Particulate Form 3.2.2.3.1 Cumulative dose contributions from Tritium and radionuclides in particulate form with half lives greater than 8 days for the current calendar quarter and current calendar year shall be determined in accordance with the OFFSITE DOSE CALCULATION MANUAL (ODCM) monthly.3.2.2.4 Ventilation Exhaust Treatment 3.2.2.4.1 Doses due to gaseous releases from the unit shall be projected monthly in accordance with the ODCM.

CY-TM-1 70-300 Revision 3 Page 92 of 209 TABLE 3.2-2 Radioactive Gaseous Waste Sampling and Analysis Program (3)SAMPLING TYPE OF DETECTABLE SAMPLE FREQUENC ACTIVITY CONCENTRATION SAMPLE POINT TYPE Y ANALYSIS (1)(a)P H-3 1 E-6 pCi/cc Reactor Building Purge Gas Individual Releases Each Purge Gamma Emitters 1E-4 tCi/cc (2)M H-3 1E-6 gCi/cc Unit Exhaust Vent Release Gas Individual Points Monthly Gamma Emitters 1 E-4 gtCi/cc (2)W Individual (b) 1E-10 pCi/cc (2)Weekly Gamma Emitters M Particulate Monthly Sr-90 1 E-1 1 p.Ci/cc s Composite M Monthly Gross Alpha Mnhy Emitters 1 E-1 1 gCi/cc Composite Indv. Gam ma 1E 10 g ic 2 Reactor Building Breather SA Emitters (b) E- Ci/cc (2)Particulate SAEitr(b Semi-Annual Sr-90 1 E-1 1 gCi/cc ly Gross Alpha 1 E-1 1 pCi/cc Emitters 1E-11_____i/cc (1) The above detectability limits are based on technical feasibility and on the potential significance in the environment of the quantities released.

For some nuclides, lower detection limits may be readily achievable and when nuclides are measured below the stated limits, they should also be reported.(2) For certain mixtures of gamma emitters, it may be possible to measure radionuclides at levels near their sensitivity limits when other nuclides are present in the sample at much higher levels. Under these circumstances, it will be more appropriate to calculate the levels of such radionuclides using observed ratios in the gaseous component in the reactor coolant for those radionuclides which are measurable.

(3) Deviations from the sampling and analysis regime will be noted in the report specified in ODCM Part IV.

CY-TM-1 70-300 Revision 3 Page 93 of 209 TABLE 3.2-2 (Cont'd)Radioactive Gaseous Waste Sampling and Analysis Program Table Notation a. The LLD is the smallest concentration of radioactive material in a sample that will be detected with 95% probability with 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):

4.66 sp LED =E x V x 2.22 x 106 x Y x exp (-XAt)Where LLD is the lower limit of detection as defined above (as picocurie per unit mass or volume).Sb is the standard deviation of the background counting rate or of the counting rate of a blank sample as appropriate (as counts per minute).E is the counting efficiency (as counts per transformation), V is the sample size (in units of mass or volume), 2.22 is the number of transformations per minute per picocurie, Y is the fractional radiochemical yield (when applicable), X is the radioactive decay constant for the particular radionuclide, and At is the elapsed time between midpoint of sample collection and time of counting (for plant effluents, not environmental samples), The value of Sb used in the calculation of the LLD for a detection system shall be based on the actual observed variance of the background counting rate or of the counting rate of the blank samples (as appropriate) rather than on an unverified theoretically predicted variance.

In calculating the LLD for a radionuclide determined by gamma-ray spectrometry, the background shall include the typical contributions of other radionuclides normally present in the samples. Typical values of E, V, Y, and At shall be used in the calculation.

The background count rate is calculated from the background counts, that are determined to be with +/-one FWHM (Full-Width-at-Half-Maximum) energy band about the energy of the gamma-ray peak used for the quantitative analysis for that radionuclide.

CY-TM-170-300 Revision 3 Page 94 of 209 TABLE 3.2-2 Notation (Cont'd)b. The principal gamma emitters for which the LLD specification applies exclusively are the following radionuclides:

Mn-54, Fe-59, Co-58, Co-60, Zn-65, Mo-99, Cs-1 34, Cs-1 37, Ce-141 and Ce-1 44 for particulate emissions.

This list does not mean that only these nuclides are to be detected and reported.

Other peaks which are measurable and identifiable, together with the above nuclides, shall also be identified and reported.

Nuclides which are below the LLD for the analyses shall be reported as "less than" the nuclide's LLD and shall not be reported as being present at the LLD level for that nuclide. The "less than" values shall not be used in the required dose calculations.

CY-TM-170-300 Revision 3 Page 95 of 209 3.2.3 Total Radioactive Effluents 3.2.3.1 Dose Calculation 3.2.3.1.1 Cumulative annual dose contributions from liquid and gaseous effluents shall be determined in accordance with Surveillances 3.2.1.2.1, 3.2.2.2.1, and 3.2.2.3.1, including direct radiation contributions from the Unit and from outside storage tanks, and in accordance with the methodology contained in the ODCM.

CY-TM-1 70-300 Revision 3 Page 96 of 209 4.0 PART II REFERENCES 4.1 NUREG-0683, "Final Programmatic Environmental Impact Statement related to decontamination and disposal of radioactive wastes resulting from March 28, 1979, accident Three Mile Island Nuclear Station, Unit 2," March 1981, and its supplements.

4.2 TMI-2 PDMS Technical Specifications, attached to Facility License No. DPR-73 4.3 Title 10, Code of Federal Regulations, "Energy" 4.4 "Statement of Policy Relative to the NRC Programmatic Environmental Impact Statement on the Cleanup of Three Mile Island Unit 2," dated April 27, 1981 4.5 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977 4.6 DOE/TIC-27601, Atmospheric Science and Power Reduction 4.7 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-50 4.8 PDMS-SAR CY-TM-170-300 Revision 3 Page 97 of 209 PART III EFFLUENT DATA AND CALCULATIONAL METHODOLOGIES CY-TM-170-300 Revision 3 Page 98 of 209 1.0 LIQUID EFFLUENT MONITORS 1.1 TMI-1 and TMI-2 Liquid Radiation Monitor Set Points The liquid effluent off-line monitors are set such that the concentration(s) of radionuclides in the liquid effluents will not exceed ten times the concentrations specified in 10 CFR 20, Appendix B Table 2, Col 2. Table 1.1 lists the Liquid Effluent Release Points and their parameters; Figure 1.1 provides a Liquid Release Pathway Diagram.To meet the above limit, the alarm/trip set points for liquid effluent monitors and flow measuring devices are set in accordance with the following equation:* f< C (eq 1.1)F+f -Where: C = ten times the effluent concentration of 10 CFR 20 for the site, in giCi/ml.c = the set point, in giCi/ml, of the liquid effluent monitor measuring the radioactivity concentration in the effluent line prior to dilution and release.The set point is inversely proportional to the maximum volumetric flow of the effluent line and proportional to the minimal volumetric flow of the dilution stream plus the effluent stream. The alert set point value is set to ensure that advance warning occurs prior to exceeding any limits. The high alarm set point value is such that if it were exceeded, it would result in concentrations exceeding ten times the 10 CFR 20 concentrations for the unrestricted area.f = flow set point as measured at the radiation monitor location, in volume per unit time, but in the same units as F below.F = flow rate of dilution water measured prior to the release point, in volume per unit time.The set point concentration is reduced such that concentration contributions from multiple release points would not combine to exceed ten times 10 CFR 20 concentrations.

The set point concentration is converted to set point scale units using appropriate radiation monitor calibration factors.This section of the ODCM is implemented by the Radiation Monitor System Set Points procedure and, for batch releases, the Releasing Radioactive Liquid Waste procedure.

CY-TM-1 70-300 Revision 3 Page 99 of 209 1.2 TMI Liquid Effluent Release Points and Liquid Radiation Monitor Data TMI-1 has two required liquid radiation monitors.

These are RM-L6 and RM-L12.These liquid release point radiation monitors and sample points are shown in Table 1.1. (The TMI outfall radiation monitor, RM-L7, is also listed for information only.)TMI-2 does not have any required liquid radiation monitors, but does utilize RM-L12, and RM-L7 for release of liquid waste.1.2.1 RM-L6 RM-L6 is an off-line system, monitoring radioactive batch discharges from the TMI-1 liquid radwaste system (see Figure 1.1). These batch releases are sampled and analyzed per site procedures prior to release.The release rate is based on releasing one of two Waste Evaporator Condensate Storage Tanks (WECST) at a flow which will add less than 10%, of ten times the 10 CFR 20 concentrations

[20% for H-3] to radionuclide concentrations in the unrestricted area, including conservative default values for Sr-89, Sr-90, and Fe-55.The release flow rate used is the most restrictive of two flow rates calculated for each liquid batch release, per the approved plant procedure.

Two Dilution Factors (DF) are calculated to ultimately calculate the batch release flow rate. These two DF's are calculated to insure each radionuclide released to the unrestricted area is less than 10 percent of ten times the 10CFR20 radionuclide concentrations, (20% for H-3), and to ensure each liquid batch release boron concentration to the river will not exceed 0.7 ppm.The maximum release flow rate is then calculated by dividing the most restrictive (largest)

DF into 90 percent of the current dilution flow rate of the Mechanical Draft Cooling Tower (MDCT). This conservative flow rate is then multiplied by 0.9 for the allowable flow rate.* Calculation of the 10CFR20 concentration DF: DFI = :-Y (SA 1) -(10% [20% for H-3] often times the IOCFR20 concentration)

SA = Specific Activity of each identified radionuclide

  • Calculation of Boron DF: DF 2= Actual Tank Boron Concentration

+ 0.7.

CY-TM-170-300 Revision 3 Page 100 of 209 Maximum release flow rate calculation:

Max Flow = [(MDCT flow gpm

  • 0.9) -(Most Restrictive DF)] *0.9 The dilution flow rate used is the current flow rate at the site. The minimum dilution flow rate is 5000 gpm per the TMI-1 FSAR. This ensures this batch release will meet the following equation.YX(CI/Xi)

+ (CH-3/2XH-3)

< 0.1, (eq 1.2)Where: Ci = diluted concentration of the ith radionuclide, other than H-3 Xi= Ten times the concentration for that radionuclide in the unrestricted area (10 CFR 20, App. B, Table 2, Col. 2). A value of 3E-3 jtCi/ml for dissolved and entrained noble gases shall be used.CH.3 = diluted concentration of H-3 XH-3 = Ten times the concentration for H-3 in the restricted area (10 CFR 20, App. B, Table 2, Col. 2).The set points for RM-L6 are based on the maximum release rate (30 gpm), a minimum dilution flow (5000 gpm), and 25% of ten times the 1OCFR20 concentration for Cs-1 37, which is the most limiting radionuclide at a concentration of 1.OE-5 uCi/ml. These inputs are used in Equation 1.1 to determine the RM-L-6 High Alarm setpoint for all radionuclides being released.

A high alarm on RM-L-6 will close valve WDL-V-257 and terminate any WECST releases to the environment.

1.2.2 RM-L12 RM-L12 is an off-line system, monitoring periodic combined releases from the Industrial Waste Treatment System/Industrial Waste Filtration System (IWTS/IWFS).

The input to IWTS/IWFS originates in TMI-2 sumps, (see Figures 1.1 and 1.2) and the TMI-1 Turbine Building sump (see Figure 1.1). The set points are based on the maximum release rate from both IWTS and IWFS simultaneously, (see Figure 1.1) a minimum dilution flow rate, and 50% of ten times the 10CFR20 concentration for Cs-1 37, which is the most limiting radionuclide at a concentration of 1E-5 ýtCi/ml. These inputs are used in equation 1.1 to determine the RM-L12 High Alarm set point for all radionuclides being released.

A high alarm on RM-L12 will close IWTS and IWFS release valves and trip release pumps to stop the release.

CY-TM-1 70-300 Revision 3 Page 101 of 209 1.2.3 RM-L1O RM-L1O was a Nal detector submerged in the TMI-1 Turbine Building Sump. This detector has been removed from service.1.2.4 RM-L7 RM-L7 is not an ODCM required liquid radiation monitor. RM-L7 is an off-line system, monitoring the TMI outfall to the Susquehanna River (see Figures 1.1 and 1.2). This monitor is the final radiation monitor for TMI-1 and TMI-2 normal liquid effluent releases.1.3 Control of Liquid Releases TMI liquid effluent releases are controlled to less than ten times the 1OCFR20 concentrations by limiting the percentage of this limit allowable from the two TMI liquid release points. RM-L6 and effluent sampling limit batch releases to less than or equal to 25% for all radionuclides, and RM-L12 and effluent sampling limit releases from TMI-1 and TMI-2 to less than or equal to 50% for Cs-1 37.These radiation monitor set points also include built in meter error factors to further ensure that TMI liquid effluent releases are less than ten times the 1OCFR20 concentrations to the environment.

The radioactivity content of each batch of radioactive liquid waste is determined prior to release by sampling and analysis in accordance with ODCM Part I Table 3.2-1 or ODCM Part II, Table 3.2-1. The results of analyses are used with the calculational methods in Section 1.1, to assure that the concentration at the point of release is maintained within the ODCM Part I Control 2.2.1.1, and ODCM Part II Control 2.2.1.1.Post-release analysis of samples composited from batch releases are performed in accordance with ODCM Part I Table 3.2-1 or ODCM Part II Table 3.2-1. The results of the previous post-release analysis shall be used with the calculational methods in the ODCM to assure that the concentrations at the point of release were maintained within the ODCM Part I Control 2.2.1.1, and ODCM Part II Control 2.2.1.1.The radioactivity concentration of liquids discharged from continuous release points are determined by collection and analysis of samples in accordance with ODCM Part I Table 3.2-1, or ODCM Part II Table 3.2-1. The results of the analysis are used with the calculational methods of the ODCM to assure that the concentration at the point of release is maintained within the ODCM Part I Control 2.2.1.1, and ODCM Part II Control 2.2.1.1.

CY-TM-170-300 Revision 3 Page 102 of 209 TABLE 1.1 TMI Liquid Release Point and Liquid Radiation Monitor Data RELEASE LIQUID RADIATION LIQUID RELEASE TERMINATION MONITOR POINT (Maximum DISCHARGE FLOW INTERLOCK (DETECTOR)

LOCATION Volume) RECORDER (YES/NO) VALVES RM-L6 281' Elevation WECST Batch YES (Nal) TMI-1 Auxiliary Bldg Releases (8000 gal.) WDL-V257 RM-L7 South end of TMI-1 Station Discharge YES (Nal) MDCT TMI-1 and SR-FT-146 WDL-V257** TMI-2, *WDL-R-1 311 YES IWTS/IWFS IW-V73, RM-L12 IWFS Building NW Continuous Releases IW-FT-342/

IW-P16,17,18 (Nal) Corner (300,000/

IW-FT-373 80,000 gal.) IW-V279, I_ IW-P29,30* WDL-R-1311 has been flanged off as a TMI-2 liquid outfall.** RM-L7 is not an ODCM required liquid radiation monitor.

CY-TM-170-300 Revision 3 Page 103 of 209 TABLE 1.2 TMI-2 Sump Capacities Total Capacity Gallons Sump Gallons per Inch Turbine Building Sump 1346 22.43 Circulating Water Pump House Sump 572 10.59 Control Building Area Sump 718 9.96 Tendon Access Galley Sump 538 9.96 Control to Service Building Sump 1346 22.43 Contaminated Drain Tank Room Sump 135 3.80 Chlorinator House Sump ........Water Treatment Sump** 1615 22.43 Air Intake Tunnel Normal Sump 700 ----Air Intake Tunnel Emergency Sump 100000 766.00 Condensate Polisher Sump* 2617 62.31 Sludge Collection Sump** 1106 26.33 Heater Drain Sump ----.....Solid Waste Staging Facility Sump 1476 24.00 Auxiliary Building Sump 10102 202.00 Decay Heat Vault Sump 479 10.00 Building Spray Vault Sump 479 10.00* Condensate Polisher Sump is deactivated and in PDMS condition.

    • The Water Treatment and Sludge Collection Sumps will be deactivated for PDMS.

CY-TM-1 70-300 Revision 3 Page 104 of 209 FIGURE 1-1 TMI-1 Liquid Effluent Pathways Page 1 of 1 CY-TM-1 70-300 Revision 3 Page 105 of 209 FIGURE 1.2 TMI-2 Liquid Effluent Pathways CONTROL CONTROL &BUILDING SERVICE SUMP AREA SUMP INDUSTRIAL WASTE TREATMENT SYSTEM C -- COMPOSITE SAMPLER CY-TM-1 70-300 Revision 3 Page 106 of 209 2.0 LIQUID EFFLUENT DOSE ASSESSMENT 2.1 Liquid Effluents

-10 CFR 50 Appendix I The dose from liquid effluents results from the consumption of fish and drinking water. The location of the nearest potable water intake is PP&L Brunner Island Steam Electric Station located downstream of TMI. The use of the flow of the Susquehanna River as the dilution flow is justified based on the complete mixing in the river prior to the first potable water supply, adequately demonstrated by flume tracer die studies and additional liquid effluent release studies conducted using actual TMI-1 tritium releases.

Other pathways contribute negligibly at Three Mile Island. The dose contribution from all radionuclides in liquid effluents released to the unrestricted area is calculated using the following expression:

Dose j (At) X () X AW ij X- + (AF ij X f X 1 (eq 2.1)Doej. AtX(C) LAWJFR) FD DF Where: Dose j = the cumulative dose commitment to the total body or any organ, j, from the liquid effluents for the total time period, in mrem.At = the length of the time period of actual releases, over which Ci and f are averaged for all liquid releases, in hours.C = the average concentration of radionuclide, i, in undiluted liquid effluent during time period At from any liquid release, in ýLCi/ml.NOTE: For Fe-55, Sr-89, Sr-90, prior to batch releases conservative concentration values will be used in the initial dose calculation based on similar past plant conditions.

LLD values are not used in dose calculations.

f = undiluted liquid waste flow, in gpm.FD = plant dilution water flowrate during the period of release, in gpm FR = actual river flowrate during the period of release or average river lowrate for the month the release is occurring, in gpm.DF = dilution factor as a result of mixing effects in the near field of the discharge structure of 0.2 (NUREG 0133) or taken to be 5 based on the inverse of 0.2.AWij and AFij = the site-related ingestion dose commitment factor to the total body or any organ, j, for each identified principle gamma and beta emitter, in mrem/hr per pCi/ml. AW is the factor for the water pathway and AF is the factor for the fish pathway.

CY-TM-1 70-300 Revision 3 Page 107 of 209 Values for AWij are determined by the following equation: AWij = (1.14E5) x (Uw) x (DFij) (eq 2.2)Where: 1.14E5 = (1.0E6 pCilpjCi) x (1.0E3 mi/kg) + (8760 hrlyr)Uw = Water consumption rate for adult is 730 kg/yr (Reg. Guide 1.109, Rev. 1).DFij = ingestion dose conversion factor for radionuclide, i, for adults total body and for "worst case" organ, j, in mrem/pCi, from Table 2.1 (Reg. Guide 1.109)Values for AFij are determined by the following equation: AFij = (1.14E5) x (Uf) x (DFij) x (BFi) (eq 2.2.2)where: 1.14E5 = defined above Uf = adult fish consumption, assumed to be 21 kg/yr (Reg. Guide 1.109, Rev. 1).DFij = ingestion dose conversion factor for radionuclide, i, for adult total body and for "worst case" organ, j, in mrem/pCi, from Table 2.1 (Reg. Guide 1.109, Rev. 1).BFi = Bioaccumulation factor for radionuclide, i, in fish, in pCi/kg per pCi/L from Table 2.2 (Reg. Guide 1.109, Rev. 1).2.2 TMI Liquid Radwaste System Dose Calcs Once Per Month ODCM Part I Control 2.2.1.3 and TMI-2 PDMS Tech Spec Section 6.7.4.a.6 requires that appropriate portions of the liquid radwaste treatment system shall be used to reduce the radioactive materials in liquid wastes prior to their discharge when the monthly projected doses due to the liquid effluent releases from each unit to unrestricted areas would exceed 0.06 mrem to the total body or 0.2 mrem to any organ in any calendar month. The following calculational method is provided for performing this dose projection.

At least once per month, the total dose from all liquid releases for the quarter-to-date will be divided by the number of days into the quarter and multiplied by 31. Also, this dose projection shall include the estimated dose due to any anticipated unusual releases during the period for which the projection is made. If this projected dose exceeds 0.06 mrem total body or 0.2 mrem any organ, appropriate portions of the Liquid Radwaste Treatment System, as CY-TM-170-300 Revision 3 Page 108 of 209 defined in Section 3.1, shall be used to reduce radioactivity levels prior to release.At the discretion of the ODCM Specialist, time periods other than the current quarter-to-date may be used to project doses if the dose per day in the current quarter-to-date is not believed to be representative of the dose per day projected for the next month.2.3 Alternative Liquid Dose Calculational Methodology As an alternative, models in, or based upon, those presented in Regulatory Guide 1.109 (Rev. 1) may be used to make a comprehensive dose assessment.

Default parameter values from Reg. Guide 1.109 (Rev. 1) and/or actual site specific data are used where applicable.

As an alternative dose calculational methodology TMI calculates doses using SEEDS (simplified environmental effluent dosimetry system).The onsite and SEEDS calculational models use actual liquid release data with actual monthly Susquehanna River flow data to assess the dispersion of effluents in the river.

CY-TM-1 70-300 Revision 3 Page 109 of 209 TABLE 2.1 Liquid Dose Conversion Factors (DCF): DF 1 j Page 1 of 3 Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLI H 3 NO DATA 1.05E-07 1.05E-07 1.05E-07 1.05E-07 1.05E-07 1.05E-07 C 14 2.84E-06 5.68E-07 5.68E-07 5.68E-07 5.68E-07 5.68E-07 5.68E-07 NA 24 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06 1.70E-06 CR.51 NO DATA NO DATA 2.66E-09 1.59E-09 5.86E-10 3.53E-09 6.69E-07 MN 54 NO DATA 4.57E-06 8.72E-07 NO DATA 1.36E-06 NO DATA 1.40E-05............... ....... .. .. .. ...........

..... ..........

... ... ......... .. .. .................

..... .. ..........

.. ...... .............

......... ....MN 56 NO DATA 1.151E-07 2.04E-08 NO DATA 1.46E-07 NO DATA 3.67E-06 FE 55 2.75E-06 1.90E-06 4.43E-07 NO DATA NO DATA 1.06E-06 1.09E-06 FE 59 4.34E-06 1.02E-05 3.91E-06 NO DATA NO DATA 2.85E-06 3.40E-05 CO-58 NO DATA 7.45E-07 1.67E-06 NO DATA NO DATA NO DATA 1.51E-05 CO 60 NO DATA 2.14E-06 4.72E-06 NO DATA NO DATA NO DATA 4.02E-05 NI 63 1.30E-04 9.011E-06 4.36E-06 NO DATA NO DATA NO DATA 1.88E-06.............

.........................................................................................................

..... ....................................................

NI 65 5.28E-07 6.86E-08 3.13E-08 NO DATA NO DATA NO DATA 1.74E-06 CU 64 NO DATA 8.33E-08 3.91 E-08 NO DATA 2.1OE-07 NO DATA 7.1OE-06 ZN 65 4.84E-06 1.54E-05 6.96E-06 NO DATA 1.03E-05 NO DATA 9.70E-06.. .............................................................................................................................................................................

ZN 69 1.03E-08 1.97E-08 1.37E-09 NO DATA 1.28E-08 NO DATA 2.96E-09 BR 83 NO DATA NO DATA 4.02E-08 NO DATA NO DATA NO DATA 5.79E-08 BR 84 NO DATA NO DATA 5.21E-08 NO DATA NO DATA NO DATA 4.09E-13..............

..............

.............

..............

.............

..............

..............

.............

..............

.............

..............

.............

BR-85 NO DATA NO DATA 2.14E-09 NO DATA NO DATA NO DATA LT E-24 RB 86 NO DATA 2.11E-05 9.83E-06 NO DATA NO DATA NO DATA 4.16E-06 RB 88 NO DATA 6.05E-08 3.21 E-08 NO DATA NO DATA NO DATA 8.36E-19 RB.89 NO DATA 4.01E-08 2.82E-08 NO DATA NO DATA NO DATA 2.33E-21 SR 89 3.08E-04 NO DATA 8.84E-06 NO DATA NO DATA NO DATA 4.94E-05 SR 90 7.58E-03 NO DATA 1.86E-03 NO DATA NO DATA NO DATA 2.19E-04..R. .1 0-6E- .. -NO DATA' 2.29E-07 NO DATA NO DATA NO DATA 2.70E-05-----------------------------------------

2;2 9-f *...........---......

...... ..........*- -------SR 92 2.15E-06 NO DATA 9.30E-08 NO DATA NO DATA NO DATA 4.26E-05 Y 90 9.62E-09 NO DATA 2.58E-10 NO DATA NO DATA NO DATA 1.02E-04 CY-TM-1 70-300 Revision 3 Page 110 of 209 TABLE 2.1 Liquid Dose Conversion Factors (DCF): DF=j Page 2 of 3 Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLI Y 91M 9.09E-11 NO DATA 3.52E-12 NO DATA NO DATA NO DATA 2.67E-10 Y 91 1.41 E-07 NO DATA 3.77E-09 NO DATA NO DATA NO DATA 7.76E-05 Y 92 8.45E-10 NO DATA 2.47E-11 NO DATA NO DATA NO DATA 1.48E-05 Y 93 2.68E-09 NO DATA 7.40E-11 NO DATA NO DATA NO DATA 8.50E-05 ZR 95 3.04E-08 9.75E-09 6.60E-09 NO DATA 1.53E-08 NO DATA 3.09E-05 ZR 97 1.68E-09 3.39E-10 1.55E-10 NO DATA 5.12E-10 NO DATA 1.05E-04 NB.95 6.22E-09 3.46E-09 1.86E-09 NO DATA 3.42E-09 NO DATA 2.10E-05 MO 99 NO DATA 4.31E-06 8.20E-07 NO DATA 9.76E-06 NO DATA 9.99E-06 TC 99M 2.47E-10 6.98E-10 8.89E-09 NO DATA 1.06E-08 3.42E-10 4.13E-07.. .............................................................................................................................................................................

TC 101 2.54E-10 3.66E-10 3.59E-09 NO DATA 6.59E-09 1.87E-10 1.1OE-21 RU 103 1.85E-07 NO DATA 7.97E-08 NO DATA 7.06E-07 NO DATA 2.16E-05 RU 105 1.54E-08 NO DATA 6.08E-09 NO DATA 1.99E-07 NO DATA 9.42E-06 RU 106 2.75E-06 NO DATA 3.48E-07 NO DATA 5.31 E-06 NO DATA 1.78E-04 AG 110M 1.60E-07 1.48E-07 8.79E-08 NO DATA 2.91 E-07 NO DATA 6.04E-05 SB 125 1.79E-06 2.00E-08 4.26E-07 1.82E-09 0.0 1.38E-06 1.97E-05 TE 125M 2.68E-06 9.71 E-07 3.59E-07 8.06E-07 1.09E-05 NO DATA 1.07E-05 TE.127M 6.77E-06 2.42E-06 8.25E-07 1.73E-06 2.75E-05 NO DATA 2.27E-05 TE 127 1.10E-07 3.95E-08 2.38E-08 8.15E-08 4.48E-07 NO DATA 8.68E-06 TE 129M 1.15E-05 4.29E-06 1.82E-06 3.95E-06 4.80E-05 NO DATA 5.79E-05.. .............................................

.................................

  • ..............................................................................................

TE 129 3.14E-08 1.18E-08 7.65E-09 2.41 E-08 1.32E-07 NO DATA 2.37E-08 TE 131M 1.73E-06 8.46E-07 7.05E-07 1.34E-06 8.57E-06 NO DATA 8.40E-05 TE 131 1.97E-08 8.23E-09 6.22E-09 1.62E-08 8.63E-08 NO DATA 2.79E-09.. .............................................................................................................................................................................

TE 132 2.52E-06 1.63E-06 1.53E-06 1.80E-06 1.57E-05 NO DATA 7.71E-05 I 130 7.56E-07 2.23E-06 8.80E-07 1.89E-04 3.48E-06 NO DATA 1.92E-06 I 131 4.16E-06 5.95E-06 3.41E-06 1.95E-03 1.02E-05 NO DATA 1.57E-06 I. 132 2.03E-07 E-07 5.ZE-07 1.90E-07 1.90E-05 8.65E-07 NO DATA 1.02E-07 I 133 1.42E-06 2.47E-06 7.53E-07 3.63E-04 4.31 E-06 NO DATA 2.22E-06 I 134 1.06E-07 2.88E-07 1.03E-07 4.99E-06 4.58E-07 NO DATA 2.51 E-10 CY-TM-1 70-300 Revision 3 Page 111 of 209 TABLE 2.1 Liquid Dose Conversion Factors (DCF): DFIj Page 3 of 3 Ingestion Dose Factors for Adults*(MREM Per PCI Ingested)NUCLIDE BONE LIVER T. BODY THYROID KIDNEY LUNG GI-LLI I 135 4.43E-07 1.16E-06 4.28E-07 7.65E-05 1.86E-06 NO DATA 1.31 E-06 CS 134 6.22E-05 1.48E-04 1.21E-04 NO DATA 4.79E-05 1.59E-05 2.59E-06 CS 136 6.51 E-06 2.57E-05 1.85E-05 NO DATA 1.43E-05 1.96E-06 2.92E-06 CS.137 7.97E-05 1.09E-04 7.14E-05 NO DATA 3.70E-05 1.23E-05 2.11E-06 CS 138 5.52E-08 1.09E-07 5.40E-08 NO DATA 8.01E-08 7.91E-09 4.65E-13 BA 139 9.70E-08 6.91E-11 2.84E-09 NO DATA 6.46E-11 3.92E-11 1.72E-07 BA 140 2.03E-05 2.55E-08 1.33E-06 NO DATA 8.67E-09 1.46E-08 4.18E-05 BA 141 4.71E-08 3.56E-11 1.59E-09 NO DATA 3.31E-11 2.02E-11 2.22E-17 BA 142 2.13E-08 2.19E-11 1.34E-09 NO DATA 1.85E-11 1.24E-11 3.OOE-26.............

............

.....................................................................................................................................................

LA 140 2.50E-09 1.26E-09.

3.33E-10 NO DATA NO DATA NO DATA 9.25E-05 LA 142 1.28E-10 5.82E-11 1.45E-11 NO DATA NO DATA NO DATA 4.25E-07 CE 141 9.36E-09 6.33E-09 7.18E-10 NO DATA 2.94E-09 NO DATA 2.42E-05 CE-143 1.65E-09 1.22E-06 1.35E-10 NO DATA 5.37E-10 NO DATA 4.56E-05 CE 144 4.88E-07 2.04E-07 2.62E-08 NO DATA 1.21 E-07 NO DATA 1.65E-04 PR 143 9.20E-09 3.69E-09 4.56E-10 NO DATA 2.13E-09 NO DATA 4.03E-05 PR.144 3.01 E-11 1.25E-11 1.53E-12 NO DATA 7.05E-12 NO DATA 4.33E-18 ND 147 6.29E-09 7.27E-09 4.35E-10 NO DATA 4.25E-09 NO DATA 3.49E-05 W 187 1.03E-07 8.61 E-08 3.01E-08 NO DATA NO DATA NO DATA 2.82E-05 N-.23 9 ... --- ........ 1" .......-E.. .D , ....3"."... E'"0 NO D A -.6E- ., ...NO... D T *0E"-"5 Dose factors of internal exposure are for continuous intake over a one-year period and include the dose commitment over a 50-year period; from Reg. Guide 1.109 (Rev. 1).Additional dose factors for nuclides not included in this table may be obtained from NUREG-0172.

CY-TM-1 70-300 Revision 3 Page 112 of 209 TABLE 2.2 Bloaccumulation Factors, BF, Bioaccumulation Factors to be Used in the Absence of Site-Specific Data*(pCi/kg per pCi/liter)

ELEMENT FRESHWATER FISH INVERTEBRATE H 9.OE-01 9.OE-01 C 4.6E+03 9.1E+03 NA 1.OE+02 2.OE+02 CR 2.OE+02 2.OE+03 MN 4.OE+02 9.OE+04 FE 1.OE+02 3.2E+03 CO 5.OE+01 2.OE+02 NI 1.OE+02 1.OE+02 CU 5.OE+01 4.OE+02 ZN 2.OE+03 1.OE+04 BR 4.2E+02 3.3E+02 RB 2.OE+03 1.OE+03 SR 3.OE+01 1.OE+02 Y 2.5E+01 1.OE+03 ZR 3.3E+00 6.7E+00 NB 3.OE+04 1.OE+02 MO 1.OE+01 1.OE+01 TC 1.5E+01 5.OE+00 RU 1.OE+01 3.OE+02 RH 1.OE+01 3.OE+02***AG-110m 2.30E+1 7.70E+2**SB 1.OE+00 1.OE+00 TE 4.OE+02 6.1 E+03 I 1.5E+01 5.OE+00 CS 2.OE+03 1.OE+03 BA 4.OE+00 2.OE+02 LA 2.5E+01 1.OE+03 CE 1.OE+00 1.OE+03 PR 2.5E+01 1.OE+03 ND 2.5E+01 1.OE+03 W 1.2E+03 1.OE+01 NP 1.OE+01 4.OE+02* Bioaccumulation factor values are taken from Reg. Guide 1.109 (Rev. 1), Table A-1j.** Sb bioaccumulation factor value is taken from EPRI NP-3840.Ag bioaccumulation factor value is taken from Reg. Guide 1.109 (Rev. 0), Table A-8.

CY-TM-170-300 Revision 3 Page 113 of 209 3.0 TMI LIQUID EFFLUENT WASTE TREATMENT SYSTEM 3.1 TMI-1 Liquid Effluent Waste Treatment System 3.1.1 Description of the Liquid Radioactive Waste Treatment System (see Figure 3.1)Reactor Coolant Train a. Water Sources -(3) Reactor Coolant Bleed Tanks (RCBT)-(1) Reactor Coolant Drain Tank (RCDT)b. Liquid Processing

-Reactor Coolant Waste Evaporator

-Demineralizers prior to release (see Figure 3.2)c. Liquid Effluent for Release- (2) Waste Evaporator Condensate Storage Tanks -(WECST)d. Dilution -Mechanical Draft Cooling Tower (0-38k gpm)-River Flow (2E7 gpm average)Miscellaneous Waste Train a. Water sources: -Auxiliary Building Sump-Reactor Building Sump-Miscellaneous Waste Storage Tank-Laundry Waste Storage Tank-Neutralizer Mixing Tank-Neutralizer Feed Tank-Used Precoat Tank-Borated Water Tank Tunnel Sump-Heat Exchanger Vault Sump-Tendon Access Galley Sump-Spent Fuel Pool Room Sump-TMI-2 Miscellaneous Waste Holdup Tank CY-TM-1 70-300 Revision 3 Page 114 of 209 b. Liquid Processing

-Miscellaneous Waste Evaporator, MWE-Demineralizers prior to release (see Figure 3.2)c. Liquid Effluent for Release -(2) Waste Evaporator Condensate Storage Tanks- (WECST)d. Dilution -Mechanical Draft Cooling Tower (0-38k gpm)-River Flow (2E7 gpm average)3.2 Operability of the TMI-1 Liquid Effluent Waste Treatment System 3.2.1 The TMI-1 Liquid Waste Treatment System as described in Section 11 of the TMI-1 Final Safety Analysis Report is considered to be operable when one of each of the following pieces of equipment is available to perform its intended function: a) Miscellaneous Waste Evaporator (WDL-Z1 B) or Reactor Coolant Evaporator (WDL-Z1 A)b) Waste Evaporator Condensate Demineralizer (WDL-K3 A or B)c) Waste Evaporator Condensate Storage Tank (WDL-T 11 A or B)d) Evaporator Condensate Pumps (WDL-P 14 A or B)3.2.2 TMI-1 Representative Sampling Prior to Discharge All liquid releases from the TMI-1 Liquid Waste Treatment System are made through the Waste Evaporator Condensate Storage Tanks. To provide thorough mixing and a representative sample, the contents of the tank are recirculated using one of the Waste Evaporator Condensate Transfer Pumps.3.3 TMI-2 Liquid Effluent Waste Treatment System 3.3.1 Description of the TMI-2 Liquid Radioactive Waste Treatment System The TMI-2 Liquid Radioactive Waste Treatment System has been out of service since the TMI-2 Accident in 1979. TMI-2 Liquid Radioactive Waste is processed by the TMI-1 system described in Section 3.1 prior to release. In addition, TMI-2 releases water from various sumps and tanks to the river (see Figures 1.1 and 1.2). These processes are governed by plant procedures that encompass proper sampling, sample analysis, and radiation monitoring techniques.

CY-TM-1 70-300 Revision 3 Page 115 of 209 FIGURE 3.1 TMI-1 Liquid Radwaste CY-TM-170-300 Revision 3 Page 116 of 209 FIGURE 3.2 TMI-1 Liquid Waste Evaporators DIST.

CY-TM-1 70-300 Revision 3 Page 117 of 209 4.0 GASEOUS EFFLUENT MONITORS 4.1 TMI-1 Noble Gas Monitor Set Points The gaseous effluent monitor set points are established for each gaseous effluent radiation monitor to assure concentrations of radionuclides in gaseous effluents do not exceed the limits set forth in ODCM Part I Control 2.2.2.1.Table 4.1 lists Gaseous Effluent Release Points and their associated parameters; Figure 4.1 provides a Gaseous Effluent Release Pathway Diagram.The set points are established to satisfy the more restrictive set point concentration in the following two equations:

500> >. (c 1)(F)(K 1)(Dv) (eq 4.1.1)and 3000 > I (cq)(LI + 1.1 Mi)(Dv)(F) (eq 4.1.2)Where: ci = set point concentration based on Xe-1 33 equivalent, in iCi/cc F =gaseous effluent flowrate at the monitor, in cc/sec Ki =total body dose factor, in mrem/yr per p.Ci/m 3 from Table 4.3 Dv = highest sector annual average gaseous atmospheric dispersion factor (X/Q) at or beyond the unrestricted area boundary, in sec/m 3 , from Table 4.4 for station vent releases and Table 4.5 for all other releases, (Condenser off gas, ESF FHB, and ground releases).

Maximum values presently used are 1.27E-6 sec/m 3 at sector SE for station vent, and 1.40E-5 sec/M 3 at sector E for all other releases.Li= skin dose factor due to beta emissions from radionuclide i, in mrem/yr per jLCi/m 3 from Table 4.3.MI = air dose factor due to gamma emissions from radionuclide i, in mrad/yr per p.Ci/m 3 from Table 4.3.1.1 = mrem skin dose per mrad air dose.500 = annual whole body dose rate limit for unrestricted areas, in mrem/yr.3000 = annual skin dose rate limit for unrestricted areas, in mrem/yr.

CY-TM-1 70-300 Revision 3 Page 118 of 209 The set point concentration is further reduced such that the concentration contributions from multiple release points would not combine to exceed ODCM Control limits.The set point concentration is converted to set point scale units on each radiation monitor using appropriate calibration factors.This section of the ODCM is implemented by the Radiation Monitor System Set Points procedure and the procedure for Releasing Radioactive Gaseous Waste.

CY-TM-170-300 Revision 3 Page 119 of 209 4.2 TMI-1 Particulate and Radioiodine Monitor Set Points Set points for monitors which detect radionuclides other than noble gases are also established to assure that concentrations of these radionuclides in gaseous effluents do not exceed the limits of ODCM Part I Control 2.2.2.1.Set points are established so as to satisfy the following equations:

1500 > (ci)(F)(P 1)(Ov) (eq 4.2)Where: c 1 = set point concentration based on 1-131 equivalent for radioiodine monitor and Sr-90 for particulate monitor, in VLCi/cc F = gaseous effluent flow rate at the monitor, in cc/sec Pi = pathway dose parameter, in mrem/yr per p.Ci/m3 for the inhalation pathway from Table 4.6. The dose factors are based on the actual individual organ and most restrictive age group (child) (NUREG-0133).

NOTE: Appendix A contains Pi calculational methodology.

1500 = annual dose rate limit to any organ from particulates and radioiodines and radionuclides (other than noble gases) with half lives greater than eight days in mrem/yr.Dv = highest sector annual average gaseous dispersion factor (X/Q or D/Q) at or beyond the unrestricted area boundary from Table 4.4 for releases from the station vent and Table 4.5 for all other releases.

X/Q is used for the inhalation pathway. Maximum values of X/Q presently used are 1.27E-6 sec/m3 for station vent, at sector SE, and 1.40E-5 sec/m3 for all other releases, at sector E.The set point concentration is further reduced such that concentration contributions from multiple release points would not combine to exceed ODCM Control limits.The set point concentration is converted to set point scale units on each radiation monitor using appropriate calibration factors.This section of the ODCM is implemented by the Radiation Monitor Systems Set Points procedure and the procedure for Releasing Radioactive Gaseous Waste.

CY-TM-1 70-300 Revision 3 Page 120 of 209 4.3 TMI-2 Gaseous Radiation Monitor Set Points TMI-2 Gaseous Radiation Monitors have their set points described in TMI Plant Procedure 1101-2.1.

Figure 4.5 provides a gaseous effluent release pathway diagram. Table 4.2 provides TMI-2 Radiation Monitor Data.These set points are set in accordance with the Controls delineated in Part II of this ODCM.

CY-TM-170-300 Revision 3 Page 121 of 209 4.4 TMI-1 Gaseous Effluent Release Points and Gaseous Radiation Monitor Data TMI-1 has eleven (11) required effluent gaseous radiation monitors.

These are RM-A4, RM-A5, RM-A15, RM-A6, RM-A7, RM-A8, RM-A9, RM-A14, ALC-RMI-18, WHP-RIT-1, and RLM-RM-1.

These gaseous release points, radiation monitors, and sample points are shown in Table 4.1.4.4.1 RM-A4/RM-A6 Fuel Handling and Auxiliary Building Exhaust RM-A4 is the radiation monitor for the TMI-1 Fuel Handling Building Ventilation (see Figures 4.1 and 4.2). RM-A6 is the radiation monitor for the TMI-1 Auxiliary Building Ventilation (see Figures 4.1 and 4.2). High alarms on RM-A4 or RM-A6 noble gas channels will initiate shutdown of the related building ventilation air supply system. These two radiation monitors concurrently will satisfy requirements for the Station Vent release point in place of RM-A8.4.4.2 RM-A8 Station Ventilation Exhaust RM-A8 is the particulate, radioiodine and gaseous radiation monitor for the TMI-1 Station Ventilation (see Figures 4.1 and 4.2). This in plant effluent radiation monitor also has an associated sampling panel with sampling lines located before the sample filters. High alarm on RM-A8 noble gas low channel will initiate shutdown of the Station Ventilation air supply systems. (The Fuel Handling and Auxiliary Building Ventilation).

This radiation monitor satisfies requirements for the Station Vent release point in place of RM-A4 and RM-A6.4.4.3 RM-A5/RM-A15 Condenser Off Gas Exhaust RM-A5 is the gaseous radiation monitor for the TMI-1 Condenser Off Gas exhaust (see Figures 4.1 and 4.4). RM-A15 is the back up gaseous radiation monitor for the TMI-1 Condenser Off Gas exhaust (see Figures 4.1 and 4.4). High alarms on RM-A5 low channel or RM-A15 noble gas channels will initiate the MAP-5 Radioiodine Processor Station. These two radiation monitors together satisfy requirements for the Condenser Off Gas release point.4.4.4 RM-A7 Waste Gas Decay Tank Exhaust RM-A7 is the gaseous radiation monitor for the TMI-1 Waste Gas Decay tanks (see Figures 4.1 and 4.2). This in plant effluent radiation monitor also has an associated sampling panel. High alarm on RM-A7 noble gas channel will initiate shutdown of the Waste Gas Decay Tank release in progress.

This radiation monitor satisfies requirements for batch gaseous releases to the Station Vent release point.

CY-TM-1 70-300 Revision 3 Page 122 of 209 4.4.5 RM-A9 Reactor Building Purge Exhaust RM-A9 is the particulate, radioiodine and gaseous radiation monitor for the TMI-1 Reactor Building Purge system (see Figures 4.1 and 4.3).This in plant effluent radiation monitor also has an associated sampling panel with sampling lines located before the sample filters. High alarm on RM-A9 noble gas low channel will initiate shutdown of the Reactor Building Purge System. This radiation monitor satisfies requirements for the Reactor Building Purge System release point.4.4.6 RM-A14 ESF FHB Ventilation System RM-A14 is the gaseous radiation monitor for the TMI-1 Emergency Safeguards Features (ESF) Fuel Handling Building Exhaust system (see Figures 4.1 and 4.2). This in plant effluent radiation monitor also has an associated sampling panel with sampling lines located before the sampler filters. High alarm on RM-A14 noble gas channel will initiate shutdown of the ESF Fuel Handling Building Exhaust System. This radiation monitor satisfies requirements for the ESF Fuel Handling Building Exhaust System release point.4.4.7 ALC-RMI-18 Chemical Cleaning Facility (CCF) Ventilation Exhaust ALC-RMI-18 is an Victoreen particulate, radioiodine, and gaseous radiation monitor for the Chemical Cleaning building exhaust. This monitor is located in the Chemical Cleaning building on the ground floor, and has an associated sample panel. Sampling for particulate activity is performed off of the monitor.4.4.8 WHP-RIT-1 Waste Handlinq and Packaging Facility (WHPF) Exhaust WHP-RIT-1 is an Eberline AMS-3 particulate radiation monitor for the TMI WHPF. The monitor is located in the Mechanical Equipment Room in the WHPF. Sampling for particulate activity is performed off of the monitor. A high alarm will initiate shutdown of the ventilation air exhaust system.4.4.9 RLM-RM-1 Respirator Cleaning and Laundry Maintenance (RLM)Facility RLM-RM-1 is an Eberline AMS-3 particulate radiation monitor for the TMI RLM Facility.

The monitor is located in the Mechanical Equipment Room in the RLM. Sampling for particulate activity is performed off of the monitor.

CY-TM-1 70-300 Revision 3 Page 123 of 209 4.5 TMI-2 Gaseous Effluent Release Points and Gaseous Radiation Monitor Data TMI-2 has three (3) regulatory required gaseous effluent radiation monitors.These are HP-R-219, HP-R-219A and HP-R-225.

These gaseous release points, radiation monitors, and sample points are shown in Table 4.2, and various gaseous effluent pathways are depicted -in Figure 4.5.4.5.1 HP-R-219 Station Ventilation Exhaust HP-R-219 is a Victoreen particulate and gaseous radiation monitor for the TMI-2 ventilation exhaust. This in-plant effluent radiation monitor is located in the TMI-2 Auxiliary Building 328 foot elevation and has an associated sample panel.4.5.2 HP-R-219A Station Ventilation Exhaust HP-R-219A is a Victoreen particulate and gaseous radiation monitor for the TMI-2 ventilation exhaust. This in-plant effluent radiation monitor is located in the TMI-2 Auxiliary Building 328 foot elevation.

4.5.3 HP-R-225 Reactor Building Purge Air Exhaust Duct "A" HP-R-225 is a Victoreen particulate and gaseous radiation monitor for the TMI-2 Reactor Building Purge Air Exhaust System. This in-plant effluent radiation monitor is located in the TMI-2 Auxiliary Building 328'elevation area.

CY-TM-170-300 Revision 3 Page 124 of 209 4.6 Control of Gaseous Effluent Releases TMI gaseous effluent combined releases are controlled (per ODCM Part I for TMI-1 and ODCM Part II for TMI-2) by effluent sampling and radiation monitor set points. These measures assure that releases from the various vents do not combine to produce dose rates at the site boundary exceeding the most restrictive of 500 mrem per year to the total body or 3000 mrem per year to the skin, and 1500 mrem per year to the thyroid. This is done by restricting simultaneous releases and by limiting the dose rates that may be contributed by the various vents at any time. The various vent radiation monitor set points are each based on fractions of the above limits and do not exceed the above limits when summed together.

These effluent radiation monitor set points are calculated using the methodology described in equations 4.1.1, or 4.1.2 and 4.2.The actual set points are then listed in TMI-1 Operations Procedure 1101-2.1.The radioactive content of each batch of gaseous waste is determined prior to release by sampling and analyses in accordance with ODCM Part I for TMI-1 and ODCM Part II for TMI-2. The results of pre-release analyses are used with the calculational methods in Sections 4.1 and 4.2 to assure that the dose rates at the site boundary are maintained below the limits in ODCM Part I for TMI-1 and ODCM Part II for TMI-2.Post-release analyses of samples composited from batch and continuous releases are performed in accordance with ODCM Part I for TMI-1 and ODCM Part II for TMI-2. The results of the analyses are used to assure that the dose rates at the site boundary are maintained within the limits of ODCM Part I for TMI-1 and ODCM Part II for TMI-2.

CY-TM-170-300 Revision 3 Page 125 of 209 TABLE 4.1 TMI-1 Gaseous Release Point and Gaseous Radiation Monitor Data GASEOUS RELEASE RADIATION GASEOUS (F) TERMINATION MONITOR RELEASE FLOW INTERLOCK (YES/NO)(DETECTOR)

LOCATION POINT RECORDER VALVES YES 306 Elevation Fuel Hand. AH-E-1 0 RM-A4 Auxiliary Bldg. Building AH-FR-149 AH-D-120 Exhaust AH-D-121 AH-D-122 306' Elevation Auxiliary YES RM-A6 Auxiliary Bldg. Building AH-FR-150 AH-E-11 Exhaust YES WDG-V47 RMA-8/9 Bldg. Station AH-FR-149 AH-E-10 RA Nar Vent & AH-FR-1 50 AH-E-1 1 Exhaust Starts MAP-5 Radioiodine Sampler 322' Elevation Condenser YES RM-A5 Second Floor Off Gas VA-FR-1 113 Starts MAP-5 Turbine Bldg. Exhaust Radioiodine Sampler 322' Elevation Condenser YES RM-A1 5 Second Floor Off Gas VA-FR-1 113 Starts MAP-5 Turbine Bldg. Exhaust Radioiodine Sampler Waste Gas RM-A7 306' Elevation Decay WDG-FR-123 YES Auxiliary Bldg. Tanks WDG-V47 (A,B,C)Reactor YES Reactor AH-V-1AINB/C/D RM-A9 RMA-8/9 Bldg. Building AH-FT-909/

WDG-534/535 Near BWST Purge AH-FR-148 Starts4MAP-ExhaustStarts MAP-5 Exhaust Radioiodine Sampler 331' Elevation ESF Fuel NO RM-A14 ESF FHB Handling AH-UR-1104A/B Manual Outside Chem. Building Actions Addition Bldg. Exhaust CY-TM-1 70-300 Revision 3 Page 126 of 209 TABLE 4.1 (Cont'd)TMI-1 Gaseous Release Point and Gaseous Radiation Monitor Data RELEASE GASEOUS TERMINATION RADIATION INTERLOCK MONITOR GASEOUS (YES/NO)(DETECTOR)

LOCATION RELEASE POINT VALVES Chemical CCB Exhaust ALC-RMI-18 Cleaning Bldg. System NONE 304' Elevation (Typical flow rate is 10,000 cfm)WHPF WHPF Exhaust YES WHP-RIT-1 Mechanical System WHPF Ventilation Equipment Room (Typical flow rate Trips is 7,500 cfm)RLM Exhaust RLM-RM-1 RLM-Mechanical System NONE Equipment Room (Typical flow rate I is 900 cfm)TABLE 4.2 TMI-2 Gaseous Release Point and Gaseous Radiation Monitor Data RELEASE GASEOUS TERMINATION RADIATION GASEOUS INTERLOCK MONITOR RELEASE (YES/NO)(DETECTOR)

LOCATION POINT VALVES 328' Elevation Station HP-R-219 Auxiliary Vent NONE Building Exhaust 328' Elevation Station Vent HP-R-219A Auxiliary Exhaust NONE Building 328' Elevation Reactor Bldg HP-R-225 Auxiliary Building Purge Exhaust NONE Duct "A" CY-TM-170-300 Revision 3 Page 127 of 209 TABLE 4.3 Dose Factors for Noble Gases and Daughters*

Gamma Beta Total Body Skin Dose Dose Factor(b)

Gamma Air Beta Air Factor(a)

Li Dose Factor Dose Factor Ki (mrem/yr Mi Ni (mrem/yr per per (mrad/yr per (mrad/yr per Radionuclide pci/m 3) ýLCi/m 3) gCi/m 3) ýiCi/m 3)Kr-83m 7.56E-02**

--- 1.93E+01 2.88E+02 Kr-85m 1.17E+03 1.46E+03 1.23E+03 1.97E+03 Kr-85 1.61 E+01 1.34E+03 1.72E+01 1.95E+03 Kr-87 5.92E+03 9.73E+03 6.17E+03 1.03E+04 Kr-88 1.47E+04 2.37E+03 1.52E+04 2.93E+03 Kr-89 1.66E+04 1.01 E+04 1.73E+04 1.06E+04 Kr-90 1.56E+04 7.29E+03 1.63E+04 7.83E+03 Xe-131 m 9.15E+01 4.76E+02 1.56E+02 1.11E+03 Xe-133m 2.51 E+02 9.94E+02 .3.27E+02 1.48E+03 Xe-133 2.94E+02 3.06E+02 3.53E+02 1.05E+03 Xe-135m 3.12E+03 7.11 E+02 3.36E+03 7.39E+02 Xe-135 1.81 E+03 1.86E+03 1.92E+03 2.46E+03 Xe-137 1.42E+03 1.22E+04 1.51 E+03 1.27E+04 Xe-138 8.83E+03 4.13E+03 9.21E+03 4.75E+03 Ar-41 8.84E+03 2.69E+03 9.30E+03 3.28E+03 Dose factors are for immersion exposure in uniform semi-infinite cloud of noble gas radionuclides that may be detected in gaseous effluents.

Dose factor values are taken from Regulatory Guide 1.109 (Rev. 1), Table B-1.7.56E-02 = 7.56 x 10-2.(a) Total body dose factor for gamma penetration depth of 5 cm into the body.(b) Skin dose factor at a tissue depth or tissue density thickness of 7 mg/cm 2.

CY-TM-1 70-300 Revision 3 Page 128 of 209 TABLE 4.4 Atmospheric Dispersion Factors for Three Mile Island STATION VENT SECTOR AVERAGE X/Q (IN SEC/M 3)DISTANCE (IN SEASON -ANNUAl SECTOR 610 2413 4022 5631 7240 12067 24135 40225 56315 72405 N 1.63E-07 5.69E-07 3.62E-07 2.19E-07 1.63E-07 7.31E-08 2.99E-08 1.55E-08 1.OOE-08 7.28E-09 NNE 4.06E-07 1.1OE-06 5.84E-07 3.42E-07 2.17E-07 9.35E-08 3.58E-08 1.84E-08 1.20E-08 8.68E-09 NE 3.45E-07 3.48E-07 2.54E-07 3.86E-07 2.56E-07 1.14E-07 4.33E-08 2.22E-08 1.44E-08 1.05E-08 ENE 2.24E-07 4.54E-07 6.55E-07 3.61E-07 2.35E-07 1.20E-07 4.79E-08 2.45E-08 1.59E-08 1.15E-08 E 4.48E-07 3.99E-07 3.46E-07 4.25E-07 3.06E-07 1.31E-07 4.95E-08 2.52E-08 1.62E-08 1.17E-08 ESE 8.35E-07 5.29E-07 6.22E-07 4.00E-07 2.53E-07 1.08E-07 4.03E-08 2.03E-08 1.31E-08 9.41E-09 SE 1.27E-06 8.28E-07 5.96E-07 3.20E-07 2.05E-07 9.14E-08 3.90E-08 1.98E-08 1.28E-08 9.22E-09 SSE 7.20E-07 7.10E-07 4.94E-07 2.74E-07 1.83E-07 8.96E-08 3.36E-08 1.71E-08 1.1OE-08 7.90E-09 S 1.58E-07 1.09E-07 3.71E-07 1.98E-07 1.27E-07 6.15E-08 2.29E-08 1.15E-08 7.39E-09 5.31E-09 SSW 4.16E-08 5.78E-08 2.69E-07 1.41E-07 8.94E-08 3.88E-08 1.53E-08 7.70E-09 4.93E-09 3.54E-09 SW 5.06E-08 1.75E-07 2.59E-07 1.43E-07 8.94E-08 3.82E-08 1.42E-08 7.12E-09 4.55E-09 3.27E-09 WSW 9.31E-08 4.71E-07 3.22E-07 1.73E-07 1.1OE-07 4.68E-08 1.76E-08 8.89E-09 5.71E-09 4.12E-09 W 1.41E-07 3.31E-07 3.69E-07 2.11E-07 1.47E-07 6.90E-08 2.58E-08 1.31E-08 8.38E-09 6.03E-09 WNW 1.96E-07 2.55E-07 3.94E-07 2.75E-07 1.72E-07 7.34E-08 2.77E-08 1.41E-08 9.09E-09 6.57E-09 NW 1.37E-07 5.23E-07 3.49E-07 1.92E-07 1.26E-07 6.31E-08 2.46E-08 1.33E-08 8.62E-09 6.25E-0911 NNW 8.38E-08 5.25E-07 3.32E-07 1.87E-07 1.28E-07 6.44E-08 2.47E-08 1.26E-08 8.19E-09 5.94E-09 STATION VENT DISTANCE SECTOR AVERAGE D/Q (IN M 2) (IN METERS) SEASON -ANNUAL SECTOR 610 2413 4022 5631 7240 12067 24135 40225 56315 72405 N 5.65E-09 1.02E-09 4.24E-10 3.24E-10 2.60E-10 9.41E-11 3.05E-11 1.27E-11 6.85E-12 4.26E-12 NNE 1.28E-08 2.15E-09 1.16E-09 5.85E-10 3.44E-10 1.21E-10 3.71E-11 1.51E-11 8.14E-12 5.06E-12 NE 1.04E-08 1.37E-09 4.64E-10 6.47E-10 3.87E-10 1.44E-10 4.41E-11 1.79E-11 9.65E-12 6.OOE-12 ENE 6.91E-09 1.16E-09 8.68E-10 4.20E-10 2.59E-10 1.36E-10 4.46E-11 1.82E-11 9.78E-12 6.09E-12 E 1.45E-08 2.46E-09 8.77E-10 9.16E-10 5.97E-10 2.13E-10 6.55E-11 2.68E-11 1.45E-11 9.06E-12 ESE 2.76E-08 4.35E-09 2.30E-09 1.29E-09 7.48E-10 2.64E-10 8.11E-11 3.31E-11 1.79E-11 1.12E-11 SE 4.09E-08 5.28E-09 2.54E-09 1.19E-09 6.95E-10 2.65E-10 9.22E-11 3.75E-11 2.02E-11 1.26E-11 SSE 2.28E-08 2.80E-09 1.17E-09 6.39E-10 4.60E-10 2.09E-10 6.42E-11 2.66E-11 1.43E-11 8.91E-121 S 5.17E-09 7.98E-10 8.66E-10 4.10E-10 2.45E-10 1.16E-10 3.61E-11 1.48E-11 7.94E-12 4.93E-12 SSW 1.17E-09 2.90E-10 5.61E-10 2.61E-10 1.51E-10 5.53E-11 1.88E-11 7.64E-12 4.12E-12 2.56E-12 SW 1.78E-09 4.57E-10 5.62E-10 2.78E-10 1.59EA10 5.77E-11 1.77E-11 7.17E-12 3.86E-12 2.40E-12 WSW 2.87E-09 6.37E-10 6.40E-10 2.99E-10 1.78E-10 6.27E-11 1.92E-11 7.89E-12 4.25E-12 2.64E-12 W 5.54E-09 1.06E-09 6.25E-10 3.84E-10 2.91E-10 1.17E-10 3.60E-11 1.46E-11 7.87E-12 4.89E-12 WNW 6.71E-09 1.21E-09 7.72E-10 5.81E-10 3.32E-10 1.18E-10 3.60E-11 1.46E-11 7.86E-12 4.89E-12 NW 4.25E-09 7.99E-10 4.43E-10 2.16E-10 1.35E-10 7.25E-11 2.30E-11 1.OOE-11 5.38E-12 3.34E-12 T NNW 2.61E-09 6.15E-10 3.47E-10 1.70E-10 1.25E-10 6.32E-11 2.02E-11 8.24E-12 4.43E-12 2.75E-12 DATA FROM 2006-2010 USED IN CALCULATIONS CY-TM-1 70-300 Revision 3 Page 129 of 209 TABLE 4.5 Atmospheric Dispersion Factors for Three Mile Island GROUND RELEASE 0rf'-TrD AIr'DAfr-C VIt' I1M ccr-IRA 3\DISTANCE IlkI IjACT C ZMeAr 1MI AKIKIHAl SECTOR 610 2413 4022 5631 7240 12067 24135 40225 56315 72405 N 8.15E-06 1.01E-06 5.06E-07 3.22E-07 2.31E-07 1.18E-07 4.79E-08 2.50E-08 1.63E-08 1.19E-08 NNE 9.69E-06 1.19E-06 5.97E-07 3.81E-07 2.73E-07 1.39E-07 5.69E-08 2.97E-08 1.94E-08 1.42E-08 NE 1.19E-05 1.47E-06 7.38E-07 4.70E-07 3.36E-07 1.71E-07 6.94E-08 3.61E-08 2.36E-08 1.72E-08 ENE 1.31E-05 1.65E-06 8.26E-07 5.25E-07 3.75E-07 1.91E-07 7.72E-08 4.00E-08 2.61E-08 1.90E-08 E 1.40E-05 1.78E-06 8.83E-07 5.57E-07 3.96E-07 2.00E-07 7.98E-08 4.11E-08 2.66E-08 1.93E-08 ESE 1.19E-05 1.50E-06 7.35E-07 4.61E-07 3.26E-07 1.63E-07 6.44E-08 3.29E-08 2.12E-08 1.54E-08 SE 1.16E-05 1.43E-06 6.99E-07 4.38E-07 3.1OE-07 1.55E-07 6.18E-08 3.18E-08 2.06E-08 1.49E-08 SSE 9.94E-06 1.26E-06 6.16E-07 3.86E-07 2.73E-07 1.37E-07 5.41E-08 2.77E-08 1.79E-08 1.29E-08 S 6.77E-06 8.87E-07 4.33E-07 2.71E-07 1.91E-07 9.50E-08 3.73E-08 1.90E-08 1.22E-08 8.79E-09 SSW 4.47E-06 5.88E-07 2.87E-07 1.80E-07 1.27E-07 6.33E-08 2.49E-08 1.27E-08 8.15E-09 5.87E-09 SW 4.18E-06 5.44E-07 2.66E-07 1.66E-07 1.17E-07 5.83E-08 2.29E-08 1.16E-08 7.48E-09 5.39E-09 WSW 5.06E-06 6.49E-07 3.19E-07 2.01E-07 1.42E-07 7.12E-08 2.83E-08 1.45E-08 9.35E-09 6.76E-09 W 7.42E-06 9.56E-07 4.70E-07 2.96E-07 2.10E-07 1.05E-07 4.16E 2.13E-08 1.37E-08 9.93E-09 WNW 7.75E-06 9.78E-07 4.85E-07 3.07E-07 2.19E-07 1.10E-07 4.42E-08 2.28E-08 1.48E-08 1.08E-08 NW 7.07E-06 8.80E-07 4.41E-07 2.81E-07 2.01E-07 1.02E-07 4.15E-08 2.16E-08 1.41E-08 1.03E-08 NNW 6.67E-06 8.33E-07 4.18E-07 2.66E-07 1.90E-07 9.70E-08 3.94E-08 2.05E-08 1.34E-08 9.74E-09 GROUND RELEASE DISTANCE SECTOR AVERAGE D/Q (IN M 2 (IN METERS) SEASON -ANNUAL SECTOR 610 2413 4022 5631 7240 12067 24135 40225 56315 72405 N 1.40E-08 1.41E-09 5.78E-10 3.18E-10 2.03E-10 8.23E-11 2.61E-11 1.06E-11 5.70E-12 3.54E-12 NNE 1.92E-08 1.94E-09.

7.96E-10 4.39E-10 2.80E-10 1.13E-10 3.60E-11 1.46E-11 7.85E-12 4.88E-12 NE 1.96E-08 1.98E-09 8.11E-10 4.47E-10 2.85E-10 1.16E-10 3.67E-11 1.49E-11 8.01E-12 4.97E-12 ENE 1.93E-08 1.95E-09 7.99E-10 4.40E-10 2.81E-10 1.14E-10 3.61E-11 1.46E-11 7.88E-12 4.89E-12 E 2.95E-08 2.98E-09 1.22E-09 6.74E-10 4.30E-10 1.74E-10 5.53E-11 2.24E-11 1.21E-11 7.49E-12 ESE 3.81E-08 3.85E-09 1.58E-09 8.69E-10 5.55E-10 2.25E-10 7.13E-11 2.89E-11 1.56E-11 9.66E-12 SE 4.25E-08 4.29E-09 1.76E-09 9.70E-10 6.19E-10 2.51E-10 7.96E-11 3.23E-11 1.74E-11 1.08E-11 SSE 2.94E-08 2.97E-09 1.22E-09 6.70E-10 4.28E-10 1.73E-10 5.50E-11 2.23E-11 1.20E-11 7.46E-12 S 1.57E-08 1.59E-09 6.52E-10 3.59E-10 2.29E-10 9.28E-11 2.94E-11 1.20E-11 6.43E-12 3.99E-12 SSW 8.14E-09 8.22E-10 3.37E-10 1.86E-10 1.19E-10 4.80E-11 1.52E-11 6.18E-12 3.33E-12 2.07E-12 SW 7.89E-09 7.97E-10 3.27E-10 1.80E-10 1.15E-10 4.65E-11 1.48E-11 5.99E-12 3.22E-12 2.OOE-12 WSW 9.38E-09 9.47E-10 3.88E-10 2.14E-10 1.37E-10 5.53E-11 1.75E-11 7.12E-12 3.83E-12 2.38E-12 W 1.57E-08 1.59E-09 6.52E-10 3.59E-10 2.29E-10 9.28E-11 2.94E-11 1.19E-11 6.43E-12 3.99E-12 WNW 1.62E-08 1.64E-09 6.71E-10 3.70E-10 2.36E-10 9.56E-11 3.03E-11 1.23E-11 6.62E-12 4.11E-12 NW 1.09E-08 1.1OE-09 4.49E-10 2.48E-10 1.58E-10 6.40E-11 2.03E-11 8.24E-12 4.43E-12 2.75E-12 NNW 9.23E-09 9.33E-10 3.82E-10 2.11E-10 1.34E-10 5.45E-11 1.73E-11 7.01E-12 3.77E-12 2.34E-12 DATA FROM 2006 -2010 USED IN CALCULATIONS CY-TM-1 70-300 Revision 3 Page 130 of 209 TABLE 4.6 Dose Parameters for Radioiodines and Radioactive Particulate in Gaseous Effluents*

CRITICAL ORGAN CRITICAL ORGAN NUCLIDE ORGAN FACTOR Pi** NUCLIDE ORGAN FACTOR H-3**C-14 NA-24 P-32 CR-51 MN-54 MN-56 FE-55 FE-59 CO-58 CO-60 NI-63 NI-65 CU-64 ZN-65 ZN-69 BR-83 BR-84 BR-85 RB-86 RB-88 RB-89 SR-89 SR-90 SR-91 SR-92 Y-90 Y-91M Y-91 Y-92 Y-93 ZR-95 ZR-97 NB-95 MO-99 TC-99M TC-101 TOTAL BODY BONE TOTAL BODY BONE LUNG LUNG GI-LLI LUNG LUNG LUNG LUNG BONE GI-LLI GI-LLI LUNG GI-LLI TOTAL BODY TOTAL BODY TOTAL BODY LIVER LIVER LIVER LUNG BONE GI-LLI GI-LLI GI-LLI LUNG LUNG GI-LLI GI-LLI LUNG GI-LLI LUNG LUNG GI-LLI LUNG 3.04E-07 9.70E-06 4.35E-06 7.04E-04 4.59E-06 4.26E-04 3.33E-05 3.OOE-05 3.43E-04 2.99E-04 1.91 E-03 2.22E-04 2.27E-05 9.92E-06 2.69E-04 2.75E-06 1.28E-07 1.48E-07 6.84E-09 5.36E-05 1.52E-07 9.33E-08 5.89E-04 2.73E-02 4.70E-05 6.55E-05 7.24E-05 7.60E-07 7.1OE-04 6.46E-05 1.05E-04 6.03E-04 9.49E-05 1.66E-04 3.66E-05 1.30E-06 1.58E-07 1.12E+03 3.59E+04 1.61 E+04 2.60E+06 1.70E+04 1.58E+06 1.23E+05 1.11E+05 1.27E+06 1.11E+06 7.07E+06 8.21 E+05 8.40E+04 3.67E+04 9.95E+05 1.02E+04 4.74E+02 5.48E+02 2.53E+01 1.98E+05 5.62E+02 3.45E+02 2.16E+06 1.01 E+08 1.74E+05 2.42E+05 2.68E+05 2.81 E+03 2.63E+06 2.39E+05 3.89E+05 2.23E+06 3.51 E+05 6.14E+05 1.35E+05 4.81 E+03 5.85E+02 RU-103 RU-105 RU-106 AG-110M TE-125M SB-125 TE-127M TE-127 TE-129M TE-129 TE-131M TE-131 TE-132 1-130 1-131 1-132 1-133 1-134 1-135 CS-1 34 CS-1 36 CS-1 37 CS-138 BA-1 39 BA-140 BA-141 BA-142 LA-140 LA-142 CE-141 CE-143 CE-144 PR-143 PR-144 ND-147 W-187 NP-239 LUNG GI-LLI LUNG LUNG LUNG LUNG LUNG GI-LLI LUNG GI-LLI GI-LLI LUNG LUNG THYROID THYROID THYROID THYROID THYROID THYROID LIVER LIVER BONE LIVER GI-LLI LUNG LUNG LUNG GI-LLI GI-LLI LUNG GI-LLI LUNG LUNG LUNG LUNG GI-LLI GI-LLI 1.79E-04 2.69E-05 3.87E-03 1.48E-03 1.29E-04 6.27E-04 4.OOE-04 1.52E-05 4.76E-04 6.89E-06 8.32E-05 5.55E-07 1.02E-04 4.99E-04 4.39E-03 5.23E-05 1.04E-03 1.37E-05 2.14E-04 2.74E-04 4.62E-05 2.45E-04 2.27E-07 1.56E-05 4.71 E-04 7.89E-07 4.44E-07 6.1 OE-05 2.05E-05 1.47E-04 3.44E-05 3.23E-03 1.17E-04 4.23E-07 8.87E-05 2.46E-05 1.73E-05 6.62E+05 9.95E+04 1.43E+07 5.48E+06 4.77E+05 2.32E+06 1.48E+06 5.62E+04 1.76E+06 2.55E+04 3.08E+05 2.05E+03 3.77E+05 1.85E+06 1.62E+07 1.94E+05 3.85E+06 5.07E+04 7.92E+05 1.01E+06 1.71 E+05 9.07E+05 8.40E+02 5.77E+04 1.74E+06 2.92E+03 1.64E+03 2.26E+05 7.59E+04 5.44E+05 1.27E+05 1.20E+07 4.33E+05 1.57E+03 3.28E+05 9.1 OE+04 6.40E+04 GI-LLI 9.10E+04 LUNG 6.40E+04 -I .1.The listed dose parameters are for radionuclides, other than noble gases that may be detected in gaseous effluents.

Pi factors include all nonatmospheric pathway transport parameters, the receptor's usage of pathway media, and are based on the most restrictive age group (child) critical organ. Additional dose parameters for nuclides not included in this Table may be calculated using the methodology described in NUREG-0133.

Tritium dose factors include an increase of 50% to account for the additional amount of this nuclide absorbed through the skin.mrem/year per piCi/m 3.

CY-TM-170-300 Revision 3 Page 131 of 209 FIGURE 4.1 TMI-1 Gaseous Effluent Pathways CY-TM-1 70-300 Revision 3 Page 132 of 209 FIGURE 4.2 TMI-1 Auxiliary and Fuel Handling Buildings Effluent Pathways CY-TM-1 70-300 Revision 3 Page 133 of 209 FIGURE 4.3 TMI-1 Reactor Building Effluent Pathway Rcl 170 FEET 7--REACTOR BUILDING PURGE EXHAUST RADIATION MONITORS AND SAMPLING STATIONS REACTOR BUILDING IW3-" m4.0-a2I I I I IJ K"w =M FILTMR CR MH FIXF REACTER NUJN SmfltG SYSTENS PARTICULATUTITRHRM COMI&~E GAS C A:oIpmI CY-TM-170-300 Revision 3 Page 134 of 209 FIGURE 4.4 TMI-1 Condenser Offgas Effluent Pathway CONDENSER OFF GAS STACK CONDENSER OFF GAS EXHAUST RADIATION MONITORS AND SAMPLING STATIONS CY-TM-1 70-300 Revision 3 Page 135 of 209 FIGURE 4.5 TMI-2 Gaseous Effluent Filtration SystemlPathways STATION VENT 0o ~ 0.0 -12,oo M1 RD BREATHER--4, I --------------0 .-AM crm UNIT 2 EXHAUST AIR FLOW AND RMS SCHEMATIC CY-TM-1 70-300 Revision 3 Page 136 of 209 5.0 GASEOUS EFFLUENT DOSE ASSESSMENT 5.1 Gaseous Effluents

-Instantaneous Release Limits 5.1.1 Noble Gases For noble gases, the following equations apply for total body and skin dose rate at the unrestricted area boundary: 5.1.1.1 Total Body Dose Ratetb = z (Ki) x (Dv) x (Q 1) (eq 5.1.1.1)Where: Dose Rate b = instantaneous total body dose rate limit, at the site boundary, in mrem/yr.Ki = total body dose factor due to gamma emissions for each identified noble gas radionuclide, in mrem/yr per jiCi/m 3 from Table 4.3.Dv = highest sector annual average gaseous dispersion factor (X/Q) at or beyond the unrestricted area boundary, in sec/m 3 , from Table 4.4 for station vent releases; and Table 4.5 for all other releases (Condenser Off Gas, ESF FHB, and ground releases).

Maximum values presently in use are 1.27E-6 sec/m 3 at sector SE for station vent, and 1.40E-5 sec/m 3 for all other releases at sector E.Qi = Release rate of radionuclide, i, in p.Ci/sec as determined by sampling and analysis.

Calculated using the concentration of noble gas radionuclide, i, in ýtCi/cc, times the release pathway flow rate, in cc/second.

CY-TM-1 70-300 Revision 3 Page 137 of 209 5.1.1.2 Skin Dose Ratesk = (Li + 1.1 Mi) X (Dv) X (Qi) (eq 5.1.1.2)Where: Dose Ratesk = instantaneous mrem/year skin dose rate limit, at the site boundary, in mrem/yr.Li = skin dose factor due to beta emissions for each identified noble gas radionuclide, in mrem/yr per JLCi/m 3 from Table 4.3.Mi = air dose factor due to gamma emissions for each identified noble gas radionuclide, in mrad/yr per ýtCi/m 3 from Table 4.3.1.1 = mrem skin dose per mrad air dose. Converts air dose to skin dose.Qi = release rate of radionuclide, i, in gCi/sec, as determined by sampling and analysis.

Calculated using the concentration of noble gas radionuclide, i, in p.Ci/cc, times the release pathway flow rate, in cc/second.

Dv = highest sector annual average gaseous dispersion factor (X/Q) at or beyond the unrestricted area boundary, in sec/m 3 , from Table 4.4 for station vent releases; and Table 4.5 for all other releases (Condenser Off Gas, ESF FHB, and ground releases).

Maximum values presently in use are 1.27E-6 sec/m 3 at sector SE for station vent, and 1.40E-5 sec/m 3 for all other releases at E.

CY-TM-1 70-300 Revision 3 Page 138 of 209 5.1.2 Iodine-131, Iodine-133, Tritium and Radionuclides in Particulate Form, with Half-Lives Greater than 8 Days For 1-131, 1-133, Tritium and Radionuclides in Particulate Form, with half-lives greater than 8 days, the following equation applies: Dose Rateip = (P1) (Dv) (Qi) (eq 5.1.2)Where: Dose Rateip = mrem/year organ dose rate.Pi = dose parameter for 1-131, 1-133, Tritium and Radionuclides in Particulate Form, with half-lives greater than 8 days, for the inhalation pathway, in mrem/yr per PtCi/m 3 , from Table 4.6. The dose factors are based on the critical individual organ and most restrictive age group (child).Dv -highest sector annual average gaseous dispersion factor (X/Q or D/Q) at or beyond the unrestricted area boundary, in sec/M 3 , from Table 4.4 for the station vent releases and Table 4.5 for all other releases.

X/Q is used for the inhalation pathway. Maximum values of X/Q presently used are 1.27E-6 sec/m 3 for station vent, at sector SE, and 1.40E-5 sec/m 3 for all other releases at sector E.Q= release rate of each radionuclide, i, in pCi/sec.Calculated using the concentration of each radionuclide, i, in pCi/cc, times the release pathway flow rate, in cc/second.

CY-TM-1 70-300 Revision 3 Page 139 of 209 5.2 Gaseous Effluents

-10 CFR 50 Appendix I 5.2.1 Noble Gases The air dose in an unrestricted area due to noble gases released in gaseous effluents from the site is determined using the following expressions:

Dose F = (3.17E-8) x (MI) x (Dv) x (Qi) (eq 5.2.1)and Dose p = (3.17E-8) x f (NI) x (Dv) x (Qi) (eq 5.2.2)Where: Dose F = mrad gamma air dose due to gamma emissions from noble gas radionuclides.

Dose P = mrad beta air dose due to beta emissions from noble gas radionuclides.

MI = air dose factor due to gamma emissions for each identified noble gas radionuclide, in mrad/yr per gCi/m3, from Table 4.3.Ni = air dose factor due to beta emissions for each identified noble gas radionuclide, in mrad/yr per VLCi/m 3 , from Table 4.3.Dv = highest sector annual average gaseous dispersion factor, X/Q, at or beyond the unrestricted area boundary, in sec/m 3.Values may be read or interpolated from Table 4.4 for releases from the station vent and Table 4.5 for all other releases.

Maximum values of X/Q presently used are 1.27E-6 sec/m 3 for station vent at sector SE, and 1.40E-5 sec/m 3 for all other releases at sector E.Qi= release of noble gas radionuclide, i, in ýtCi, over the specified time period, (jiCi/second

  • seconds).3.17E-8 = inverse of the number of seconds in a year.

CY-TM-1 70-300 Revision 3 Page 140 of 209 NOTE: If the methodology in this section is used in determining dose to an individual, rather than air dose due to noble gases, substitute Ki, from Table 4.3, for Mi, and (Li + 1.1 Mi) for Ni.5.2.2 Iodine-131, Iodine-133, Tritium and Radionuclides in Particulate Form, with Half-Lives Greater than 8 Days The dose to an individual from 1-131, 1-133, Tritium and Radionuclides in Particulate Form with half-lives greater than 8 days in gaseous effluents released from the site to an unrestricted area is determined by solving the following expression:

Dose. = z (3.17E-8) x ý (Ri) (Dv) (Q 1) (eq 5.2.2)Where: Doseo = dose to all real pathways, p, to organ, o, of an individual in age group, a, from 1-131, 1-133, Tritium and Radionuclides in Particulate Form, with half-lives greater than 8 days, in mrem, during any desired time period.Ri = the dose factor for each identified radionuclide, i, pathway, p, age group, a, and organ, o, in mrem/yr perýtCi/m 3 for the inhalation pathway and m 2 -mrem/yr perýtCi/sec for other pathways, from Tables 5.2 to 5.7.NOTE: Since there is minimal or no elemental iodine released from the condenser off-gas air ejector (see NUREG-0017) all Iodine Ri values for all pathways, except the inhalation pathway, are considered to be zero when performing dose calculations for releases from the condenser off-gas air ejector. Only calculate the dose due to the inhalation pathway for condenser off-gas air ejector iodines.NOTE: Tritium, H-3, dose factor is mrem/year per pLCi/m 3 for all pathways.Dv = highest sector annual average gaseous dispersion factor (X/Q) at or beyond the unrestricted area boundary, in sec/m 3 , for the inhalation pathway, and D/Q, in m , for other pathways.

Table 4.4 is used to derive the values for station vent releases and Table 4.5 is used to derive the values for all other releases.

The values used to calculate site boundary and critical receptor doses are as follows:

CY-TM-1 70-300 Revision 3 Page 141 of 209 Station Vent Releases -Boundary -all in sector SE Inhalation X/Q 1.27E-6 Meat D/Q 4.09E-8 Ground D/Q Cow/Milk/Infant D/Q 4.09E-8 Vegetation D/Q 4.09E-8 4.09E-8 Station Vent Releases -Inhalation X/Q Meat D/Q Cow/Milk/Infant D/Q Critical Receptor 1.13E-6 in sector SE 5.93E-9 Ground D/Q in sector SE 5.93E-9 Vegetation D/Q in sector SE 2.25E-8 in sector SE 1.34E-8 in sector E Ground or Other Releases -Boundary Inhalation X/Q 1.40E-5 in sector E all in sector SE: Meat D/Q 4.25E-8 Ground D/Q Cow/Milk/Infant D/Q 4.25E-8 Vegetation D/Q 4.25E-8 4.25E-8 Ground or Other Releases -Critical Inhalation X/Q 1.12E-5 Meat D/Q 4.94E-9 Cow/Milk/Infant D/Q 4.94E-9 Receptor -all in sector E Ground D/Q 2.37E-8 Vegetation D/Q 1.92E-8 Dv(H-3) = In the case of H-3 only the X/Q's above are used for all pathways.Qi = release of 1-131, 1-133, Tritium and Radionuclides, i, in Particulate Form with half-lives greater than 8 days, in piCi, cumulative over the specified time period (ýtCi/second

  • seconds).3.17E-8 = inverse of the number of seconds in a year.

CY-TM-170-300 Revision 3 Page 142 of 209 5.3 Gaseous Radioactive System Dose Calculations Once per Month ODCM Part I Control 2.2.2.4 and TMI-2 PDMS Tech Spec Section 6.7.4.a.6 requires that appropriate subsystem of the Gaseous Radwaste Treatment System shall be used to reduce the radioactive materials in gaseous waste prior to their discharge.

When the monthly projected doses due to the gaseous effluent releases from the site would exceed: 0.2 mrad to air from gamma radiation; or 0.4 mrad to air from beta radiation; or 0.3 mrem to any organ.The following calculational method is provided for performing this dose projection.

At least once per month the gamma air dose, beta air dose and the maximum organ dose for the quarter-to-date will be divided by the number of days into the quarter and multiplied by 31. Also, this dose projection shall include the estimated dose due to any anticipated unusual release during the period for which the projection is made. If these projected doses exceed any of the values listed above, appropriate portions of the TMI-1 Gaseous Waste Treatment System, as defined in Section 6.0, or appropriate portions of the TMI-2 Gaseous Effluent Filtration System as shown on Figure 4.5, shall be used to reduce radioactivity levels prior to release.At the discretion of the ODCM Specialist, time periods other than the current quarter-to-date may be used to project doses if the dose per day in the current quarter-to-date is not believed to be representative of the dose per day projected for the next month.

CY-TM-1 70-300 Revision 3 Page 143 of 209 5.4 Alternative Gaseous Dose Calculational Methodologqy As an alternative to the methods described above, the models in/or based upon, those presented in Regulatory Guide 1.109 (Rev. 1) may be used to make a comprehensive dose assessment.

Default parameter values from Regulatory Guide 1.109 (Rev. 1) and/or actual site specific data can be used where applicable.

The onsite, on-line computerized system for tracking gaseous effluent dose uses annual average gaseous dispersion factors. As an alternative dose calculational methodology.

TMI calculates doses using an advanced class "A" dispersion model called SEEDS (simplified environmental effluent dosimetry system).This model incorporates the guidelines and methodology set forth in USNRC Regulatory Guide 1.109, and uses actual hourly meteorological information matched to the time of releases to more accurately assess the dispersion of effluents in the atmosphere.

Combining this assessment of dispersion with TMI effluent data for each unit, postulated maximum hypothetical doses to the public are calculated.

CY-TM-1 70-300 Revision 3 Page 144 of 209 TABLE 5.2.1 Pathway Dose Factors, R, AGE GROUP: INFANT PATHWAY: INHALATION NUCLIDE ORGAN DOSE FACTORS; mrem/year per iCi/m 3 NUCL _ BONI --BONE .... -LIVER- .. T.BODY " THYROID --- KIDNEY ---- LLING- G" .... GI-LLII--H-3 C-14 CR-51 MN-54 FE-55 FE-59 0.OOE+00 2.65E+04 0.OOE+00 0.OOE+00 1.97E+04 1.36E+04 6.47E+02 6.47E+02 5.31E+03 5.31E+03 0.OOE+00 8.95E+01-----------.---------

2.53E+04 4.98E+03 1.17E+04 3.33E+03 2.35E+04 9.48E+03 6.47E+02 5.31 E+03 5.75E+01 0.OOE+00 0.OOE+00 0.00E+00 6.47E+02 5.31 E+03 1.32E+01 4.98E+03 0.OOE+00 0.OOE+00 6.47E+02 6.47E+02 5.31E+03 5.31E+03 1.28E+04 3.57E+02......................

1.OOE+06 7.06E+03 8.69E+04 1.09E+03 1.02E+06 2.48E+04---------..-----------

7.77E+05 1.11E+04 4.51E+06 3.19E+04 2.09E+05 2.42E+03 6.47E+05 5.14E+04 0.OOE+00 3.04E+03 2.03E+06 6.40E+04 CO-58 0.OOE+00 1.22E+03 1.82E+03 0.OOE+00 0.OOE+00 CO-60 0.OOE+00 8.02E+03 1.18E+04 0.OOE+00 0.OOE+00 NI-63 3.39E+05 2.04E+04 1.16E+04 0.OOE+00 0.OOE+00 ZN-65 1.93E+04 6.26E+04 3.11E+04 0.OOE+00 3.25E+04 RB-86 0.OOE+00 1.90E+05 8.82E+04 0.OOE+00 0.OOE+00 SR-89 3.98E+05 0.OOE+00 1.14E+04 0.OOE+00 0.OOE+00 SR-90 Y-91 ZR-95 NB-95 RU-1 03 RU-106 AG-110M TE-125M TE-127M TE-129M 1-131 1-133 4.09E+07 5.88E+05 1.15E+05 0.OOE+00 0.OOE+00 2.79E+04 2.59E+06 I1.57E+04 2.03E+04 1.57E+04 6.43E+03 3.78E+03 2.02E+03 0.OOE+00 6.79E+02 8.68E+04 0.OOE+00 1.09E+04 9.98E+03 7.22E+03 5.OOE+03 4.76E+03 1.99E+03 6.58E+02 1.67E+04 6.90E+03 2.07E+03 0.OOE+00 0.OOE+00 0.OOE+00--.--E+--0.OOE+00 0.OOE+00 0.OOE+00 I1.62E+03 4.87E+03 5.47E+03 1.48E+07 3.56E+06 0.OOE+00 1.12E+07 1.31E+05 0.OOE+00 2.45E+06 7.03E+04 3.11E+04 1.75E+06 2.17E+04 4.72E+03 4.24E+03 1.07E+05 1.09E+04 0.OOE+00 3.75E+04 3.18E+04 5.18E+04 2.24E+04 1.41E+04 3.79E+04 1.32E+04 6.09E+03 4.44E+04 1.92E+04 2.23E+03 1.96E+04 5.60E+03 4.79E+05 1.27E+04 5.52E+05 1.61 E+04 1.16E+07 1.64E+05 3.67E+06 3.30E+04 4.47E+05 1.29E+04 1.31E+06 2.73E+04 1.68E+06 6.90E+04 0.OOE+00 1.06E+03 0.OOE+00 2.16E+03---------..-----------

7.97E+04 1.33E+03 1.18E+04 1.43E+03 7.13E+04 1.33E+03 1.60E+06 3.84E+04 5.17E+05 2.16E+04 9.84E+06 1.48E+05 CS-134 3.96E+05 CS-1 36 4.83E+04 CS-1 37 5.49E+05 BA-140 5.60E+04 CE-141 2.77E+04 CE-144 3.19E+06 7.03E+05 7.45E+04 0.OOE+00 1.35E+05 5.29E+04 0.OOE+00 6.12E+05 4.55E+04 0.OOE+00 5.60E+01 2.90E+03 0.OOE+00 1.67E+04 1.99E+03 0.OOE+00 1.21EE+06 1.76E+05 0.OOE+00 1.90E+05 5.64E+04 1.72E+05 1.34E+01 5.25E+03 5.38E+05 PR-143 1.40E+04 5.24E+03 6.99E+02 0.OOE+00 1.97E+03 4.33E+05 3.72E+04 ND-147 7.94E+03 8.13E+03 5.OOE+02 0.OOE+00 3.15E+03 3.22E+05 3.12E+04 CY-TM-1 70-300 Revision 3 Page 145 of 209 TABLE 5.2.2 Pathway Dose Factors, R, AGE GROUP: CHILD PATHWAY: INHALATION ORGAN DOSE FACTORS; mrem/year per p.Ci/m 3-BONE ---LIVER ___T.BODY

--THYROID --KIDNEY --LUNG ----GI-LLI__H-3 0.OOE+00 1.12E+03 1.12E+03 1.12E+03 1.12E+03 1.12E+03 1.12E+03 C-14 3.59E+04 6.73E+03 6.73E+03 6.73E+03 6.73E+03 6.73E+03 6.73E+03 CR-51 0.OOE+00 0.OOE+00 1.54E+02 8.55E+01 2.43E+01 1.70E+04 1.08E+03 MN-54 0.OOE+00 4.29E+04 9.51E+03 0.OOE+00 1.OOE+04 1.58E+06 2.29E+04 FE-55 4.74E+04 2.52E+04 7.77E+03 0.OOE+00 0.OOE+00 1.11E+05 2.87E+03 FE-59 2.07E+04 3.34E+04 1.67E+04 O.OOE+00 0.OOE+00 1.27E+06 7.07E+04 CO-58 0.OOE+00 1.77E+03 3.16E+03 0.OOE+00 0.OOE+00 1.11E+06 3.44E+04 CO-60 0.OOE+00 1.31E+04 2.26E+04 0.OOE+00 0.OOE+00 7.07E+06 9.62E+04 NI-63 8.21E+05 4.63E+04 2.80E+04 0.OOE+00 O.OOE+00 2.75E+05 6.33E+03................................................................................

ZN-65 4.26E+04 1.13E+05 7.03E+04 0.OOE+00 7.14E+04 9.95E+05 1.63E+04 RB-86 0.OOE+00 1.98E+05 1.14E+05 0.OOE+00 O.OOE+00 0.OOE+00 7.99E+03 SR-89 5.99E+05 O.OOE+00 1.72E+04 0.OOE+00 O.OOE+00 2.16E+06 1.67E+05 SR-90 Y-91 ZR-95 NB-95 RU-103 RU-1 06 AG-110M TE-125M TE-127M TE-129M 1-131 1-133 CS-1 34 CS-136 CS-137 BA-140 CE-141 CE-144 1.01E+08 O.OOE+00 9.14E+05 O.OOE+00 1.90E+05 4.18E+04 6.44E+06 2.44E+04 3.70E+04 0.OOE+00 0.OOE+00 0.OOE+00 O.OOE+O0 0.OOE+O0 5.96E+04 1.48E+07 2.63E+06 2.23E+06 3.43E+05 1.84E+05 6.11 E+04 2.35E+04 2.79E+03 1.36E+05 1.69E+04 6.73E+03 2.49E+04 1.92E+04 4.81E+04 1.66E+04 6.51 E+05 6.51 E+04 9.07E+05 7.40E+04 3.92E+04 6.77E+06 9.18E+03 6.55E+03 0.OOE+00 1.07E+03 0.OOE+00 1.69E+04 1.14E+04 9.14E+03 2.33E+03 9.14E+02 8.55E+03 3.02E+03 6.85E+03 3.04E+03 4.81 E+04 2.73E+04 2.03E+04 7.70E+03 1.01E+06 2.25E+05 1.71E+05 1.16E+05 8.25E+05 1.28E+05 6.48E+01 4.33E+03 1.95E+04 2.90E+03 2.12E+06 3.61 E+05 0.OOE+00 8.62E+03 0.OOE+00 7.03E+03 0.OOE+00 1.84E+05 O.OOE+00 2.12E+04 1.92E+03 0.OOE+00 6.07E+03 6.36E+04 6.33E+03 5.03E+04 1.62E+07 7.88E+04 3.85E+06 3.38E+04 O.OOE+00 3.30E+05 0.OOE+00 9.55E+04 O.OOE+00 2.82E+05 0.OOE+00 2.11E+01 0.OOE+00 8.55E+03 0.OOE+00 1.17E+06 6.14E+05 3.70E+04 6.62E+05 4.48E+04 1.43E+07 4.29E+05 5.48E+06 1.OOE+05 4.77E+05 3.38E+04 1.48E+06 7.14E+04 1.76E+06 1.82E+05 O.OOE+00 2.84E+03 O.OOE+00 5.48E+03 1.21E+05 3.85E+03 1.45E+04 4.18E+03 1.04E+05 3.62E+03 1.74E+06 5.44E+05 1.20E+07 1.02E+05 5.66E+04 3.89E+05 PR-143 1.85E+04 5.55E+03 9.14E+02 O.OOE+00 3.OOE+03 4.33E+05 9.73E+04 ND-147 1.08E+04 8.73E+03 6.81E+02 0.OOE+00 4.81E+03 3.28E+05 8.21E+04 CY-TM-1 70-300 Revision 3 Page 146 of 209 TABLE 5.2.3 Pathway Dose Factors, R, AGE GROUP: TEEN PATHWAY: INHALATION NUCLIDE [.ORGAN DOSE FACTORS; mrem/year per _iCi/m 3[ BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 0.00E+00 1.27E+03 1.27E+03 1.27E+03 1.27E+03 1.27E+03 1.27E+03 C-14 2.60E+04 4.87E+03 4.87E+03 4.87E+03 4.87E+03 4.87E+03 4.87E+03 CR-51 0.00E+00 0.00E+00 1.35E+02 7.50E+01 3.07E+01 2.10E+04 3.OOE+03 MN-54 FE-55 FE-59 CO-58 CO-60 NI-63 ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 O.00E+00 3.34E+04 1.59E+04 5.11 E+04 2.38E+04 3.70E+04 2.07E+03 1.51 E+04 4.34E+04 0.OOE+00 0.00E+00 5.80E+05 3.86E+04 1.34E+05 0.OOE+00 1.90E+05 4.34E+05 0.00E+00 1.08E+08 0.00E+00 6.61E+05 0.00E+00 1.46E+05 4.58E+04 8.40E+03 0.00E+00 5.54E+03 0.00E+00 1.43E+04 0.00E+00 2.78E+03 0.00E+00 1.98E+04 0.00E+00 1.98E+04 0.00E+00 6.24E+04--.....E.....

6.24E+04 0.00E+00 8.40E+04 0.00E+00 1.25E+04 0.00E+00 6.68E+06 0.OOE+00 1.77E+04 0.00E+00 3.15E+04 0.00E+00 5.66E+03 0.OOE+00 8.96E+02 0.00E+00 1.24E+04 O.00E+00 7.99E+03 0.00E+00 6.67E+02 1.40E+03 2.18E+03 4.38E+03 1.27E+04 0.00E+00 0.OOE+00 O.00E+00 0.OOE+00 O.OOE+00 8.64E+04 O.OOE+00 O.OOE+00 0.OOE+00 O.OOE+00 6.74E+04 1.OOE+04 7.43E+03 1.90E+05 2.50E+04 0.OOE+00 6.54E+04 5.19E+04 8.40E+04 3.59E+04 3.75E+05 1.10E+05 3.04E+05 1.98E+06 6.68E+04 1.24E+05 6.39E+03 1.53E+06 1.78E+05 1.34E+06 9.52E+04 8.72E+06 2.59E+05 3.07E+05 1.42E+04-----------.----------

1.24E+06 4.66E+04 0.OOE+00 1.77E+04 2.42E+06 3.71 E+05 1.65E+07 7.65E+05 2.94E+06 4.09E+05 2.69E+06 1.49E+05 7.51E+05 9.68E+04 7.83E+05 1.09E+05 1.61E+07 9.60E+05 6.75E+06 2.73E+05 5.36E+05 7.50E+04 1.66E+06 1.59E+05 1.98E+06 4.05E+05 0.00E+00 6.49E+03 0.00E+00 1.03E+04 1.46E+05 9.76E+03 1.78E+04 1.09E+04 1.21E+05 8.48E+03 NB-95 RU-1 03 RU-106 AG-110M TE-125M TE-127M TE-129M 1-131 1-133 CS-134 CS-136 CS-137 1.86E+2.1 0E+9.84E-+1 .38E+4.88E+1 .80E+1 .39E+3.54E-'1 .22E+5.02E-+5.15E+6.70E+-04 1.03E+04-03 0.00E+00-04 0.00E+00-04 1.31 E+04-03 2.24E+03-04 8.16E+03-04 6.58E+03-04 4.91E+04-04 2.05E+04-05 1.13E+06-04 1.94E+05-05 8.48E+05 2.25E+03 2.64E+04 6.22E+03 5.49E+05 1.37E+05 3.11 E+05 4.58E+03 1.46E+07 2.92E+06 0.OOE+00 0.OOE+00 0.OOE+00 BA-140 5.47E+04 6.70E+01 3.52E+03 0.OOE+00 2.28E+01 2.03E+06 2.29E+05 CE-141 2.84E+04 1.90E+04 2.17E+03 0.OOE+00 8.88E+03 6.14E+05 1.26E+05 CE-144 4.89E+06 2.02E+06 2.62E+05 0.OOE+00 1.21E+06 1.34E+07 8.64E+05 PR-143 1.34E+04 5.31E+03 6.62E+02 0.OOE+00 3.09E+03 4.83E+05 2.14E+05 ND-147 7.86E+03 8.56E+03 5.13E+02 0.OOE+00 5.02E+03 3.72E+05 1.82E+05 CY-TM-1 70-300 Revision 3 Page 147 of 209 TABLE 5.2.4 Pathway Dose Factors, R 1 AGE GROUP: ADULT PATHWAY: INHALATION ORGAN DOSE FACTORS; mrem/year per iLCi/m 3 NUCLIDE T---D- THYROID KIDNEY L -LL-___ _ ___-___ _ BONE -_ -LIVER -._T.13ODY

--THYROID --KIDNEY --LUNG ----GI-LLI_H-3 O.OOE+00 1.26E+03 1.26E+03 1.26E+03 C-14 1.82E+04 3.41E+03 3.41E+03 3.41E+03 CR-51 0.OOE+00 O.OOE+00 1.OOE+02 5.95E+01 MN-54 0.OOE+00 3.96E+04 6.30E+03 0.OOE+00 FE-55 2.46E+04 1.70E+04 3.94E+03 O.OOE+00 FE-59 1.18E+04 2.78E+04 1.06E+04 O.OOE+00 1.26E+03 3.41 E+03 2.28E+01 9.84E+03 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 6.90E+04 0.OOE+00 0.OOE+00 1.26E+03 1.26E+03 3.41E+03 3.41E+03 1.44E+04 3.32E+03 1.40E+06 7.74E+04 7.21E+04 6.03E+03 1.02E+06 1.88E+05---------..-----------

9.28E+05 1.06E+05 5.97E+06 2.85E+05 1.78E+05 1.34E+04-----------.----------

8.64E+05 5.34E+04 0.OOE+00 1.66E+04 1.40E+06 3.50E+05 CO-58 CO-60 NI-63 ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 NB-95 RU-1 03 RU-106 AG-110M TE-125M TE-127M TE-129M 1-131 1-133 0.OOE+00 0.OOE+00 4.32E+05 3.24E+04 0.OOE+00 3.04E+05 9.92E+07 4.62E+05 1.07E+05 1.41 E+04 1.53E+03 6.91 E+04 1.08E+04 3.42E+03 1.26E+04 9.76E+03 2.52E+04 8.64E+03 1.58E+03 1.15E+04 3.14E+04 1.03E+05 1.35E+05 0.OOE+00 2.07E+03 1.48E+04 1.45E+04 4.66E+04 5.90E+04 8.72E+03 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00-0.OOE+00 0.OOE+00 0.OOE+00 6.10E+06 0.OOE+00 1.24E+04 3.44E+04 2.33E+04 7.82E+03 4.21 E+03 0.OOE+00 6.58E+02 0.OOE+00 8.72E+03 1.OOE+04 5.94E+03 1.58E+03 4.67E+02 5.77E+03 1.57E+03 4.67E+03 1.58E+03 3.58E+04 2.05E+04 1.48E+04 4.52E+03 8.48E+05 7.28E+05 1.46E+05 1.10E+05 6.21E+05 4.28E+05 4.90E+01 2.57E+03 1.35E+04 1.53E+03 1.43E+06 1.84E+05 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 5.42E+04 0.OOE+00 7.74E+03 0.OOE+00 5.83E+03 0.OOE+00 1.34E+05 0.OOE+00 1.97E+04 1.05E+03 1.24E+04 3.29E+03 4.58E+04 3.44E+03 3.66E+04 1.19E+07 6.13E+04 2.15E+06 2.58E+04 0.OOE+00 2.87E+05 0.OOE+00 8.56E+04 0.OOE+00 2.22E+05 0.OOE+00 1.67E+01 0.OOE+00 6.26E+03 0.OOE+00 8.48E+05 9.60E+06 1.70E+06 1.77E+06 5.05E+05 5.05E+05 9.36E+06 4.63E+06 3.14E+05 9.60E+05 1.16E+06 0.OOE+00 0.OOE+00 9.76E+04 1.20E+04 7.52E+04 1.27E+06 3.62E+05 7.78E+06 7.22E+05 3.85E+05 1.50E+05 1.04E+05 1.1OE+05 9.12E+05 3.02E+05 7.06E+04 1.50E+05 3.83E+05 6.28E+03 8.88E+03 1.04E+04 1.17E+04 8.40E+03 CS-1 34 CS-1 36 CS-1 37 BA-140 CE-141 CE-144 3.73E+05 3.90E+04 4.78E+05 3.90E+04 1.99E+04 3.43E+06 2.18E+05 1.20E+05 8.16E+05 PR-143 9.36E+03 3.75E+03 4.64E+02 0.OOE+00 2.16E+03 2.81E+05 2.OOE+05 ND-147 5.27E+03 6.10E+03 3.65E+02 0.OOE+00 3.56E+03 2.21E+05 1.73E+05 CY-TM-1 70-300 Revision 3 Page 148 of 209 TABLE 5.3.1 Pathway Dose Factors, R, AGE GROUP: ALL PATHWAY: GROUND PLANE ORGAN DOSE FACTORS*NUCLIDE -- ----------T.BODY SKIN H-3 0.OOE+00 O.OOE+00 C-14 O.OOE+00 0.OOE+00 CR-51 4.65E+06 5.50E+06 MN-54 1.39E+09 1.62E+09 FE-55 O.OOE+00 0.OOE+00 FE-59 2.73E+08 3.21 E+08 CO-58 3.79E+08 4.44E+08 CO-60 2.15E+10 2.53E+10 NI-63 0.OOE+00 O.OOE+00-------------------------.

ZN-65 7.47E+08 8.59E+08 RB-86 8.97E+06 1.03E+07 SR-89 2.16E+04 2.51 E+04---------------------------


1 SR-90 0.OOE+00 0.OOE+00 Y-91 1.07E+06 1.21 E+06 ZR-95 2.45E+08 2.84E+08 NB-95 1.37E+08 1.61 E+08 RU-103 1.08E+08 1.26E+08 RU-106 4.22E+08 5.06E+08 AG-1i1M 3.44E+09 4.01"E+09'TE-125M 1.55E+06 2.13E+06:TE-127M 9.17E+04 1.08E+05:TE-129M 1.98E+07 2.31E+07:1-131 1.72E+07 2.09E+07:1-133 2.45E+06 2.98E+06 CS-134 6.86E+09 8.OOE+09 CS-136 1.51E+08 1.71E+08 CS-137 1.03E+10 1.20E+10---------------------

BA-140 2.06E+07 2.36E+07 CE-141 1.37E+07 1.54E+07 CE-144 6.96E+07 8.05E+07-------------------------

PR-143 0.OOE+00 0.OOE+00 ND-147 8.39E+06 1.01E+07* m 2-mrem/year per ýiCi/sec.

CY-TM-1 70-300 Revision 3 Page 149 of 209 TABLE 5.4.1 Pathway Dose Factors, R, AGE GROUP: INFANT PATHWAY: GRASS-COW-MILK N ORGAN DOSE FACTORS; m2 -mrem/year per pCi/sec NU----- BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 C-14 CR-51 MN-54 FE-55 FE-59 CO-58 CO-60 NI-63 ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 0.OOE+00 2.34E+09 0.OOE+00 O.OOE+00 1.35E+08 2.25E+08 0.OOE+00 0.OOE+00 3.50E+10 5.56E+09 0.OOE+00 1.26E+10 1.22E+11 7.34E+04 6.81 E+03 2.38E+03 2.38E+03 2.38E+03 2.38E+03 5.OOE+08 5.OOE+08 5.OOE+08 5.OOE+08 0.OOE+00 1.61E+05 1.05E+05 2.30E+04-----------.----------------------------

3.91E+07 8.85E+06 O.OOE+00 8.65E+06 8.74E+07 2.34E+07 0.OOE+00 0.OOE+00 3.93E+08 1.55E+08 0.OOE+00 0.OOE+00 2.43E+07 6.06E+07 O.OOE+00 O.OOE+00 8.83E+07 2.08E+08 O.OOE+00 0.OOE+00 2.16E+09 1.21E+09 0.OOE+00 0.OOE+00-----------.----------------------------

1.91E+10 8.79E+09 0.OOE+00 9.24E+09 2.23E+10 1.10E+10 0.OOE+00 0.OOE+00 0.OOE+00 3.62E+08 O.OOE+00 0.OOE+00 0.OOE+00 3.10E+10 0.OOE+00 0.OOE+00 0.OOE+00 1.95E+03 0.OOE+00 0.OOE+00 1.66E+03 1.18E+03 0.OOE+00 1.79E+03 2.38E+03 2.38E+03 5.OOE+08 5.OOE+08 2.05E+05 4.70E+06......................

0.OOE+00 1.43E+07 4.27E+07 1.11E+07 1.16E+08 1.88E+08 O.OOE+00 6.05E+07 O.OOE+00 2.10E+08 0.OOE+00 1.08E+08......................

O.OOE+00 1.61E+10 O.OOE+00 5.70E+08 0.OOE+00 2.59E+08 O.OOE+00 1.52E+09 O.OOE+00 5.26E+06 O.OOE÷00 8.27E+05 NB-95 RU-103 RU-1 06 AG-11iM TE-125M TE-127M TE-129M 1-131 1-133 CS-134 CS-1 36 CS-1 37 BA-140 CE-141 CE-144 5.94E+05 8.68E+03 1.91E+05 3.86E+08 1.51 E+08 4.22E+08 5.58E+08 2.72E+09 3.63E+07 3.65E+10 1.98E+09 5.15E+10 2.42E+08 4.34E+04 2.33E+06 2.45E+05 1.41 E+05 0.OOE+00 2.90E+03 0.OOE+00 2.38E+04-----------.---------

2.82E+08 1.87E+08 5.05E+07 2.04E+07 1.40E+08 5.1OE+07-----------.---------

1.91E+08 8.59E+07 3.21E+09 1.41E+09 5.29E+07 1.55E+07-----------.---------

6.81E+10 6.88E+09 5.83E+09 2.18E+09 6.03E+10 4.27E+09 O.OOE+00 1.75E+05 O.OOE+00 1.81E+04 0.OOE+00 2.25E+05 0.OOE+00 4.03E+08 5.08E+07 0.OOE+00 1.22E+08 1.04E+09 2.14E+08 1.39E+09 1.05E+12 3.75E+09 9.62E+09 6.22E+07 0.OOE+00 1.75E+10 0.OOE+00 2.32E+09 O.OOE+00 1.62E+10 0.OOE+00 2.07E+08 0.OOE+00 1.06E+05 0.OOE+00 1.45E+06 0.OOE+00 1.46E+10 0.OOE+00 7.19E+07 O.OOE+00 1.70E+08 0.OOE+00 3.33E+08 O.OOE+00 1.15E+08 0.OOE+00 8.96E+06 7.19E+09 1.85E+08 4.75E+08 8.85E+07 6.55E+09 1.89E+08 1.49E+05 5.94E+07 0.OOE+00 1.37E+07 O.OOE+00 1.34E+08 2.42E+05 1.25E+07 0.OOE+00 5.75E+04 2.65E+04 3.12E+03 0.OOE+00 8.17E+03 9.53E+05 1.30E+05 0.OOE+00 3.85E+05 PR-143 1.49E+03 5.56E+02 7.37E+01 O.OOE+00 2.07E+02 O.OOE+00 7.84E+05 ND-147 8.83E+02 9.07E+02 5.55E+01 0.OOE+00 3.50E+02 O.OOE+00 5.75E+05 CY-TM-1 70-300 Revision 3 Page 150 of 209 TABLE 5.4.2 Pathway Dose Factors, R, AGE GROUP: CHILD PATHWAY: GRASS-COW-MILK N ORGAN DOSE FACTORS; m2 -mrem/year per giCi/sec NUCLI BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 C-14 CR-51 MN-54 FE-55 FE-59 CO-58 CO-60 NI-63 ZN-65 RB-86 SR-89 O.OOE+00 1.57E+03 1.57E+03 1.20E+09 2.39E+08 2.39E+08 O.00E+00 0.OOE+00 1.02E+05 O.OOE+00 2.1OE+07 5.59E+06 1.12E+08 5.94E+07 1.84E+07 1.20E+08 1.95E+08 9.70E+07 0.OOE+00 1.21E+07 3.72E+07 0.00E+00 4.32E+07 1.27E+08 2.97E+10 1.59E+09, 1.01E+09 4.14E+09 1.10E+10 6.86E+09 0.OOE+00 8.78E+09 5.40E+09 6.63E+09 O.OOE+00 1.89E+08 1 .57E+03 2.39E+08 5.65E+04 O.00E+0O 0.OOE+0O O.00E+0O 0.OOE+OO 0.OOE+OO 0.OOE+OO 0.OOE+OO 0.OOE+0O 0.OOE+00 SR-90 Y-91 ZR-95 NB-95 RU-1 03 RU-106 1.12E+11 3.91 E+04 3.84E+03 3.18E+05 4.29E+03 9.25E+04 AG-110M 2.09E+08 TE-125M 7.39E+07 TE-127M 2.08E+08 TE-129M 2.72E+08 1-131 1.31E+09 1-133 1.72E+07 CS-1 34 2.27E+10 CS-1 36 1.01 E+09 CS-1 37 3.23E+10 0.OOE+00 2.84E+10 0.OOE+00 1.05E+03 8.43E+02 7.51 E+02 1.24E+05 8.86E+04 0.OOE+00 1.65E+03 0.OOE+00 1.15E+04 1.41E+08 1.13E+08 2.OOE+07 9.85E+06 5.61 E+07 2.47E+07-----------.---------

7.59E+07 4.22E+07 1.31E+09 7.46E+08 2.13E+07 8.05E+06 3.72E+10 7.85E+09 2.79E+09 1.80E+09 3.09E+10 4.56E+09 0.OOE+00 0.OOE+00 0.OOE+O0 0.OOE+00 0.OOE+00 0.OOE+O0 0.OOE+00 2.07E+07 4.98E+07 8.76E+07 4.34E+i 1 3.95E+09--.--E+--O.OOE+00 0.OOE+00 1.57E+03 1.57E+03 2.39E+08 2.39E+08 1.54E+04 1.03E+05 5.89E+06 0.OOE+00 O.OOE+00 3.36E+07 O.OOE+00 5.65E+07 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 O.OOE+00 6.95E+09 0.OOE+00 0.OOE+00 0.OOE+00 O.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 O.OOE+00 1.21 E+03 0.OOE+00 1.16E+05 0.OOE+00 1.08E+04 0.OOE+00 1.25E+05 0.OOE+00 2.63E+08 0.OOE+00 0.OOE+00 0.OOE+00 5.94E+08 0.OOE+00 7.98E+08 0.OOE+00 2.16E+09 0.OOE+00 3.55E+07 0.OOE+00 1.15E+10 4.14E+09 1.49E+09 2.21E+08 1.01E+10 3.62E+09 1.57E+03 2.39E+08 5.40E+06 1.76E+07 1.1OE+07 2.03E+08 7.08E+07 2.39E+08 1.07E+08 1.94E+09 5.65E+08 2.57E+08 1.51 E+09 5.21 E+06 8.80E+05 2.29E+08 1.11E+05 1.44E+06 1.68E+10 7.13E+07 1.69E+08 3.31 E+08 1.17E+08 8.58E+06 2.01 E+08 9.80E+07 1.93E+08 BA-140 1.18E+08 1.03E+05 6.86E+06 0.OOE+00 3.35E+04 6.14E+04 5.96E+07 CE-141 2.19E+04 1.09E+04 1.62E+03 0.OOE+00 4.79E+03 0.OOE+00 1.36E+07 CE-144 1.63E+06 5.09E+05 8.67E+04 0.00E+00 2.82E+05 0.OOE+00 1.33E+08 PR-143 7.18E+02 2.16E+02 3.56E+01 0.OOE+00 1.17E+02 0.OOE+00 7.75E+05 ND-147 4.45E+02 3.61E+02 2.79E+01 0.OOE+00 1.98E+02 0.OOE+00 5.71E+05 CY-TM-170-300 Revision 3 Page 151 of 209 TABLE 5.4.3 Pathway Dose Factors, R, AGE GROUP: TEEN PATHWAY: GRASS-COW-MILK NULIEORGAN DOSE FACTORS; M2_ mrem/year per gCilsec BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 0.00E+00 9.93E+02 9.93E+02 9.93E+02 9.93E+02 9.93E+02 9.93E+02 C-14 4.86E+08 9.73E+07 9.73E+07 9.73E+07 9.73E+07 9.73E+07 9.73E+07 CR-51 0.OOE+00 0.OOE+00 4.99E+04 2.77E+04 1.09E+04 7.13E+04 8.39E+06 MN-54 FE-55 FE-59 0.OOE+00 4.46E+07 5.19E+07 1.40E+07 3.16E+07 1.21E+08 2.78E+06 7.37E+06 4.68E+07 O.OOE+00 4.19E+06 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 2.01 E+07 3.82E+07 2.88E+07 1.37E+07 2.86E+08 CO-58 O.OOE+00 CO-60 0.OOE+00 NI-63 1.18E+10 ZN-65 2.11 E+09 RB-86 O.OOE+00 SR-89 2.68E+09 7.94E+06 1.83E+07 2.78E+07 6.27E+07 8.36E+08 4.01 E+08-----------.---------

7.32E+09 3.42E+09 4.73E+09 2.22E+09 0.OOE+00 7.67E+07 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 1.1OE+08 0.OOE+00 O.OOE+00 3.62E+08 0.00E+00 0.00E+00 1.33E+08 4.69E+09 0.00E+00 3.10E+09 0.OOE+00 0.OOE+00 7.OOE+08 0.OOE+00 0.OOE+00 3.19E+08 0.OOE+00 0.00E+00 1.86E+09 0.00E+00 0.00E+00 6.48E+06 7.65E+02 0.00E+00 1.20E+06--------------------.----------

7.58E+04 0.OOE+00 3.34E+08 6.39E+03 0.OOE+00 1.51E+05 7.24E+04 0.00E+00 1.80E+06 SR-90 6.62E+10 Y-91 1.58E+04 ZR-95 1.65E+03 NB-95 1.41 E+05 RU-103 1.81E+03 RU-106 3.76E+04 0.OOE+00 1.63E+10 0.OOE+00 4.24E+02 5.21 E+02 3.58E+02.....................

7.82E+04 4.30E+04 0.OOE+00 7.75E+02 0.OOE+00 4.73E+03 9.12E+07 5.55E+07 1.08E+07 4.02E+06 3.OOE+07 1.OOE+07 0.00E+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 8.40E+06 2.01 E+07 AG-110M TE-125M TE-127M 9.64E+07 3.01 E+07 8.45E+07 1.74E+08 0.00E+00 3.42E+08 0.00E+00 2.56E+10 0.OOE+00 8.87E+07 0.OOE+00 2.11E+08 TE-129M 1-131 1-133 CS-1 34 CS-1 36 CS-1 37 BA-140 CE-141 CE-144 1.10E+08 4.09E+07 5.38E+08 7.53E+08 7.08E+06 1.20E+07 9.83E+09 2.31E+10 4.49E+08 1.77E+09 1.34E+10 1.78E+10 4.87E+07 5.97E+04 8.89E+03 5.94E+03 6.59E+05 2.73E+05 1.74E+07 3.56E+07 4.05E+08 2.20E+11 3.66E+06 1.68E+09-.-------------------

1.07E+10 0.OOE+00 1.19E+09 0.OOE+00 6.21E+09 0.OOE+00 3.14E+06 0.OOE+00 6.82E+02 0.00E+00 3.54E+04 0.OOE+00 4.61E+08 0.OOE+00 4.14E+08 1.30E+09 0.O0E+00 1.49E+08 2.11E+07 0.00E+00 9.09E+06 7.35E+09 2.81E+09 2.88E+08 9.63E+08 1.52E+08 1.42E+08 6.06E+09 2.36E+09 2.54E+08 2.02E+04 4.01E+04 7.51E+07 2.80E+03 0.OOE+00 1.70E+07 1.63E+05 0.OOE+00 1.66E+08 PR-143 2.90E+02 1.16E+02 1.44E+01 0.OOE+00 6.73E+01 0.OOE+00 9.55E+05 ND-147 1.81E+02 1.97E+02 1.18E+01 0.00E+00 1.16E+02 0.OOE+00 7.12E+05 CY-TM-170-300 Revision 3 Page 152 of 209 TABLE 5.4.4 Pathway Dose Factors, R, AGE GROUP: ADULT PATHWAY: GRASS-COW-MILK NUCLIDE ---- ORGAN DOSE FACTORS; M2_ mrem/year per p.Cilsec[-BONE -_ -LIVER -_ T.BODY --THYROID -KIDNEY --LUNG ----GI-LLI--H-3 C-14 CR-51 MN-54 FE-55 FE-59 0.OOE+00 2.63E+08 0.OOE+00 0.OOE+00 2.51 E+07 2.97E+07 7.62E+02 7.62E+02 5.26E+07 5.26E+07 0.OOE+00 2.85E+04 8.40E+06 1.60E+06 1.73E+07 4.04E+06 6.97E+07 2.67E+07 7.62E+02 5.26E+07 1.70E+04 0.OOE+00 0.OOE+00 0.OOE+00 CO-58 0.OOE+00 CO-60 0.00E+00 NI-63 6.72E+09 ZN-65 1.37E+09 RB-86 0.OOE+00 SR-89 1.45E+09 SR-90 4.67E+10 Y-91 8.57E+03 ZR-95 9.41 E+02 NB-95 8.24E+04 RU-103 1.02E+03 RU-106 2.04E+04 AG-110M 5.81E+07 TE-125M 1.63E+07 TE-127M 4.57E+07 TE-129M 6.01E+07 1-131 2.96E+08 1-133 3.87E+06 CS-1 34 5.64E+09 CS-1 36 2.63E+08 CS-1 37 7.37E+09 4.71E+06 1.05E+07 0.00E+00 1.64E+07 3.61E+07 0.00E+00 4.65E+08 2.25E+08 0.OOE+00-----------.-------------------

4.36E+09 1.97E+09 0.00E+00 2.59E+09 1.21E+09 0.00E+00 0.OOE+00 4.16E+07 0.00E+00 0.00E+00 1.15E+10 0.OOE+00 0.00E+00 2.29E+02 0.OOE+00 3.02E+02 2.04E+02 0.OOE+00 4.58E+04 2.46E+04 0.00E+00 0.00E+00 4.38E+02 0.00E+00 0.00E+00 2.58E+03 O.00E+00-----------.-------------------

5.38E+07 3.19E+07 0.00E+00 5.89E+06 2.18E+06 4.89E+06 1.63E+07 5.57E+06 1.17E+07 7.62E+02 7.62E+02 5.26E+07 5.26E+07 6.28E+03 3.78E+04 2.50E+06 0.OOE+00 0.00E+00 9.66E+06 0.00E+00 1.95E+07 0.OOE+00 0.00E+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 2.91 E+09 0.00E+00 0.00E+00 0.OOE+00 0.00E+00 0.00E+00 0.OOE+00 0.00E+00 0.OOE+00 0.00E+00 4.74E+02 0.00E+00 4.53E+04 0.00E+00 3.88E+03 0.00E+00 3.93E+04 0.00E+00 7.62E+02 5.26E+07 7.17E+06 2.57E+07 9.93E+06 2.32E+08 9.54E+07 3.08E+08 9.71E+07 2.74E+09 5.10E+08 2.32E+08 1.35E+09 4.72E+06 9.57E+05 2.78E+08 1.19E+05 1.32E+06 2.24E+07 9.51 E+06 4.23E+08 2.42E+08 6.73E+06 2.05E+06-----------.----------

1.34E+10 1.10E+10 1.04E+09 7.48E+08 1.01E+10 6.60E+09 2.06E+07 1.39E+11 9.88E+08 0.00E+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 1.06E+08 6.61 E+07 1.86E+08 2.51 E+08 7.25E+08 1.17E+07 4.34E+09 5.78E+08 3.42E+09 1.15E+04 1.52E+03 8.85E+04 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 1.44E+09 7.92E+07 1.14E+09 1.94E+04 0.OOE+00 0.OOE+00 2.19E+10 6.49E+07 1.53E+08 3.02E+08 1.12E+08 6.04E+06 2.35E+08 1.18E+08 1.95E+08 5.54E+07 1.25E+07 1.21E+08 BA-140 CE-141 CE-144 2.69E+07 4.84E+03 3.57E+05 3.38E+04 3.27E+03 1.49E+05 1.76E+06 3.71 E+02 1.92E+04 PR-143 1.57E+02 6.32E+01 7.81E+00 0.OOE+00 3.65E+01 0.OOE+00 6.90E+05 ND-147 9.40E+01 1.09E+02 6.50E+00 0.OOE+00 6.35E+01 0.OOE+00 5.22E+05 CY-TM-1 70-300 Revision 3 Page 153 of 209 TABLE 5.5.1 Pathway Dose Factors, R, AGE GROUP: INFANT PATHWAY: GRASS-GOAT-MILK S .ORGAN DOSE FACTORS; M2 _ mrem/year per jCi/sec NU LI E -- -- -- ..-L- ------ ----- ---------6 ..G ---...-- -- --- --------- BONE -_ -LIVER T. BODY --THYROID --KIDNEY -LUNG- .GI-LLI_H-3 0.00E+00 4.86E+03 4.86E+03 4.86E+03 4.86E+03 4.86E+03 4.86E+03 C-14 2.34E+09 5.00E+08 5.OOE+08 5.00E+08 5.OOE+08 5.OOE+08 5.00E+08 CR-51 0.00E+00 0.OOE+00 1.94E+04 1.26E+04 2.76E+03 2.46E+04 5.64E+05................................................................................

MN-54 0.OOE+00 FE-55 1.76E+06 FE-59 2.92E+06 CO-58 0.OOE+00 CO-60 0.OOE+00 NI-63 4.19E+09 ZN-65 6.67E+08 RB-86 0.00E+00 SR-89 2.65E+l0 SR-90 2.55E+1 1 Y-91 8.80E+03 ZR-95 8.17E+02 NB-95 7.13E+04 RU-1 03 1.04E+03 RU-106 2.28E+04 4.68E+06 1.06E+06 1.14E+06 3.03E+05 5.10E+06 2.01E+06-----------.----------

2.91 E+06 7.26E+06 1.06E+07 2.50E+07 2.59E+08 1.46E+08-........1.....E......

2.29E+09 1.05E+09 2.67E+09 1.32E+09 0.00E+00 7.59E+08 0.OOE+00 6.50E+10 O.00E+00 2.34E+02 1.99E+02 1.41E+02 2.93E+04 1.70E+04 O.OOE+00 3.48E+02 0.00E+00 2.85E+03 O.OOE+00 0.OOE+0O 0.00E+00 1 .04E+06 0.00E+00 O.00E+00 0.00E+00 5.55E+05 1.51 E+06 0.00E+00 O.OOE+00 O.OOE+00 0.00E+OO 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+O0 0.00E+00 6.09E+06 1 .46E+07 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 O.00E+00 O.00E+00 1.11E+09 O.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 O.00E+00 O.OOE+00 2.15E+02 O.OOE+00 2.10E+04 0.00E+00 2.17E+03 0.00E+00 2.70E+04 O.00E+00 4.84E+07 0.OOE+00 0.OOE+00 0.00E+00 1.24E+08 0.00E+00 1.72E+06 1.44E+05 2.44E+06 7.25E+06 2.52E+07 1.29E+07 1.93E+09 6.83E+07 5.44E+08 3.19E+09 6.31 E+05 9.91 E+04 2.48E+07 1.27E+04 1.73E+05 1.75E+09 8.62E+06 2.04E+07 AG-110M 4.63E+07 3.38E+07 TE-125M 1.81E+07 6.05E+06 TE-127M 5.06E+07 1.68E+07 TE-129M 6.69E+07 2.29E+07 1-131 3.27E+09 3.85E+09 1-133 4.36E+07 6.35E+07............................

CS-134 1.09E+11 2.04E+11 CS-136 5.94E+09 1.75E+10 CS-137 1.54E+11 1.81E+11 BA-140 2.90E+07 2.90E+04 CE-141 5.21E+03 3.18E+03 CE-144 2.79E+05 1.14E+05 2.24E+07 2.45E+06 6.12E+06 1.03E+07 2.57E+07 1.67E+08 0.OOE+00 3.99E+07 1.69E+09 1.27E+12 4.50E+09 0.OOE+00 1.37E+08 1.86E+07 1.15E+10 7.46E+07 0.00E+00 1.07E+07-.---------------------------------------.----------

2.06E+10 0.OOE+00 5.26E+10 2.15E+10 5.55E+08 6.52E+09 0.00E+00 6.96E+09 1.42E+09 2.65E+08 1.28E+10 0.00E+00 4.85E+10 1.96E+10 5.65E+08 1.50E+06 3.74E+02 1.56E+04 O.OOE+0O 0.OOE+00 0.00E+00 6.89E+03 9.79E+02 4.62E+04 1.78E+04 0.00E+00 0.OOE+00 7.13E+06 1.64E+06 1.60E+07 PR-143 1.78E+02 6.66E+01 8.83E+00 0.OOE+00 2.48E+01 0.OOE+00 9.40E+04 ND-147 1.06E+02 1.09E+02 6.66E+00 0.OOE+00 4.19E+01 0.OOE+00 6.89E+04 CY-TM-1 70-300 Revision 3 Page 154 of 209 TABLE 5.5.2 Pathway Dose Factors, R, AGE GROUP: CHILD PATHWAY: GRASS-GOAT-MILK NUCLIDE ORGAN DOSE -mrem/year per jiCi/sec BONE LIVER T.BODY -THYROID KIDNEY LN- G I-LLI H-3 0.00E+00 3.20E+03 3.20E+03 3.20E+03 3.20E+03 C-14 1.20E+09 2.39E+08 2.39E+08 2.39E+08 2.39E+08 CR-51 0.OOE+00 0.OOE+00 1.22E+04 6.78E+03 1.85E+03 MN-54 0.OOE+00 2.52E+06 6.71E+05 0.OOE+00 7.06E+05 FE-55 1.45E+06 7.71E+05 2.39E+05 0.OOE+00 0.OOE+00 FE-59 1.56E+06 2.53E+06 1.26E+06 0.OOE+00 0.OOE+00 CO-58 0.OOE+00 1.46E+06 4.46E+06 0.00E+00 0.OOE+00 CO-60 0.OOE+00 5.18E+06 1.53E+07 0.00E+00 0.OOE+00 NI-63 3.56E+09 1.91E+08 1.21E+08 0.OOE+00 0.OOE+00 3.20E+03 3.20E+03 2.39E+08 2.39E+08 1.24E+04 6.48E+05 0.00E+00 2.11E+06 4.36E+05 1.43E+05 7.34E+05 2.64E+06 0.OOE+00 8.49E+06 0.OOE+00 2.87E+07 0.OOE+00 1.28E+07.ZN-65 4.96E+08 1.32E+09 8.22E+08 0.OOE+00 8.33E+08 O.OOE+00 2.32E+08 RB-86 0.OOE+00 1.05E+09 6.47E+08 0.OOE+00 0.OOE+00 0.OOE+00 6.77E+07 SR-89 1.39E+10 O.OOE+00 3.97E+08 0.OOE+00 0.OOE+00 0.OOE+00 5.39E+08 SR-90 2.35E+11 0.OOE+00 5.95E+10 Y-91 4.69E+03 0.OOE+00 1.25E+02 ZR-95 4.60E+02 1.01E+02 9.OOE+01 NB-95 3.82E+04 1.49E+04 1.06E+04 RU-103 5.14E+02 0.OOE+00 1.98E+02 RU-106 1.11E+04 0.OOE+00 1.38E+03 AG-110M 2.51E+07 1.69E+07 1.35E+07 TE-125M 8.86E+06 2.40E+06 1.18E+06 TE-127M 2.50E+07 6.72E+06 2.96E+06.......................................

TE-129M 3.26E+07 9.10E+06 5.06E+06 1-131 1.57E+09 1.57E+09 8.95E+08 1-133 2.06E+07 2.55E+07 9.66E+06.......................................

CS-1 34 6.80E+10 1.12E+11 2.35E+10 CS-1 36 3.04E+09 8.36E+09 5.41 E+09 CS-137 9.68E+10 9.26E+10 1.37E+10 0.OOE+00 0.OOE+00 0.OOE+00--.--E+--O O.OOE+00 0.OOE+00 0.OOE+00 2.49E+06 5.97E+06 1 .05E+07 5.21 E+l11 4.74E+09 0.OOE+00 0.OOE+00 3.16E+09 0.OOE+00 0.OOE+00 6.24E+05 1.45E+02 0.OOE+00 1.05E+05...............................

1.40E+04 1.29E+03 1.50E+04 3.15E+07 O.OOE+00 7.12E+07 9.56E+07 2.58E+09 4.25E+07 0.OOE+00 2.75E+07 0.OOE+00 1.33E+04 0.OOE+00 1.73E+05 0.OOE+00 2.01E+09 0.OOE+00 8.55E+06 O.00E+00 2.02E+07......................

0.00E+00 3.97E+07 0.OOE+00 1.40E+08 0.00E+00 1.03E+07 0.OOE+00 3.46E+10 1.24E+10 6.01E+08 0.OOE+00 4.45E+09 6.64E+08 2.94E+08 0.OOE+00 3.02E+10 1.09E+10 5.80E+08 BA-140 1.41E+07 1.24E+04 8.23E+05 0.OOE+00 4.02E+03 7.37E+03 7.15E+06 CE-141 2.63E+03 1.31E+03 1.95E+02 0.OOE+00 5.74E+02 0.00E+00 1.63E+06 CE-144 1.95E+05 6.11E+04 1.04E+04 0.OOE+00 3.38E+04 0.OOE+00 1.59E+07 PR-143 8.61E+01 2.59E+01 4.27E+00 0.OOE+00 1.40E+01 0.00E+00 9.29E+04 ND-147 5.34E+01 4.33E+01 3.35E+00 0.OOE+00 2.37E+01 0.OOE+00 6.85E+04 CY-TM-170-300 Revision 3 Page 155 of 209 TABLE 5.5.3 Pathway Dose Factors, R, AGE GROUP: TEEN PATHWAY: GRASS-GOAT-MILK N ORGAN DOSE FACTORS; m -mrem/year per jiCi/sec NUCLIDE BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 0.OOE+00 2.04E+03 C-14 4.86E+08 9.72E+07 CR-51 0.OOE+00 0.OOE+00 MN-54 0.00E+00 1.68E+06 FE-55 5.79E+05 4.11E+05 FE-59 6.74E+05 1.57E+06 2.04E+03 9.72E+07 5.99E+03 3.34E+05 9.58E+04 6.08E+05 2.04E+03 9.72E+07 3.33E+03 0.00E+00 0.00E+00 0.OOE+00 2.04E+03 2.04E+03 9.72E+07 9.72E+07 1.31E+03 8.55E+03 5.02E+05 0.OOE+00 0.OOE+00 2.61E+05 0.OOE+00 4.96E+05 2.04E+03 9.72E+07 1.01 E+06 3.45E+06 1.78E+05 3.72E+06 CO-58 CO-60 NI-63 ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 NB-95 RU-1 03 RU-106 0.00E+00 9.53E+05 0.OOE+00 3.34E+06 1.42E+09 1.00E+08 2.53E+08 8.78E+08 0.OOE+00 5.67E+08 5.62E+09 0.OOE+00 1.39E+11 0.00E+00 1.90E+03 0.OOE+00 1.98E+02 6.25E+01 1.69E+04 9.38E+03 2.17E+02 0.00E+00 4.50E+03 0.00E+00 2.20E+06 0.OOE+00 7.52E+06 O.00E+00 4.81E+07 O.00E+00 4.10E+08 O.00E+00 2.67E+08 0.00E+00 1.61 E+08 0.00E+00 3.43E+10 0.00E+00 5.09E+01 0.OOE+00 4.30E+01 0.OOE+00 5.16E+03 O.00E+00 9.29E+01 0.OOE+00 5.68E+02 O.00E+00 0.OOE+00 0.OOE+00 1.31E+07 0.OOE+00 0.00E+00 4.35E+07 0.OOE+00 0.00E+00 1.60E+07 5.62E+08 0.00E+00 3.72E+08 0.00E+00 0.OOE+00 8.40E+07 0.00E+00 0.00E+00 6.69E+08 0.OOE+00 0.OOE+00 3.90E+09 0.OOE+00 0.OOE+00 7.78E+05 9.18E+01 0.OOE+00 1.44E+05 9.09E+03 0.00E+00 4.01E+07 7.66E+02 0.00E+00 1.82E+04 8.69E+03 0.00E+00 2.16E+05 AG-110M 1.16E+07 1.09E+07 6.65E+06 0.00E+00 2.09E+07 0.00E+00 3.07E+09 TE-125M 3.61E+06 1.30E+06 4.82E+05 1.01E+06 0.OOE+00 0.OOE+00 1.06E+07 TE-127M 1.01E+07 3.59E+06 1.20E+06 2.41E+06 4.11E+07 0.00E+00 2.52E+07 TE-129M 1.32E+07 4.90E+06 2.09E+06 4.26E+06 5.53E+07 0.OOE+00 4.96E+07 1-131 6.45E+08 9.03E+08 4.85E+08 2.64E+11 1.56E+09 0.00E+00 1.79E+08 1-133 8.49E+06 1.44E+07 4.40E+06 2.01E+09 2.53E+07 0.00E+00 1.09E+07 CS-1 34 CS-1 36 CS-1 37 2.95E+l 0 1.35E+09 4.02E+l 0 6.93E+10 5.30E+09 5.34E+1 0 3.22E+10 3.56E+09 1.86E+l0 0.00E+00 0.00E+00 0.OOE+00 2.20E+1 0 2.89E+09 1.82E+10 8.41 E+09 4.55E+08 7.07E+09 8.62E+08 4.27E+08 7.60E+08 BA-140 5.84E+06 7.16E+03 3.76E+05 0.OOE+00 2.43E+03 4.81E+03 9.01E+06 CE-141 1.07E+03 7.12E+02 8.18E+01 0.OOE+00 3.35E+02 0.00E+00 2.04E+06 CE-144 7.90E+04 3.27E+04 4.25E+03 0.OOE+00 1.95E+04 0.00E+00 1.99E+07 PR-143 3.48E+01 1.39E+01 1.73E+00 0.OOE+00 8.08E+00 0.OOE+00 1.15E+05 ND-147 2.18E+01 2.37E+01 1.42E+00 0.00E+00 1.39E+01 0.OOE+00 8.54E+04 CY-TM-1 70-300 Revision 3 Page 156 of 209 TABLE 5.5.4 Pathway Dose Factors, R, AGE GROUP: ADULT PATHWAY: GRASS-GOAT-MILK NUCLIDE I::::::- ORGAN DOSE FACTORS; m2 -mrem/year per gCi/sec BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 0.00E+00 1.56E+03 C-14 2.64E+08 5.27E+07 CR-51 0.OOE+00 0.00E+00 MN-54 0.00E+00 1.01E+06 FE-55 3.27E+05 2.26E+05 FE-59 3.87E+05 9.09E+05 1.56E+03 1.56E+03 5.27E+07 5.27E+07 3.43E+03 2.05E+03 1.93E+05 0.OOE+00 5.26E+04 0.OOE+00 3.48E+05 O.OOE+00 1.56E+03 1.56E+03 5.27E+07 5.27E+07 7.56E+02 4.55E+03 3.01E+05 0.00E+00 O.00E+00 1.26E+05 0.00E+00 2.54E+05 1.56E+03 5.27E+07 8.63E+05 3.1OE+06 1.30E+05 3.03E+06 CO-58 0.OOE+00 5.66E+05 1.27E+06 O.OOE+00 0.OOE+00 0.00E+00 1.15E+07 CO-60 0.OOE+00 1.97E+06 4.35E+06 0.00E+00 0.OOE+00 0.OOE+00 3.70E+07 NI-63 8.08E+08 5.60E+07 2.71E+07 O.00E+00 0.OOE+00 0.OOE+00 1.17E+07................................................................................

ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 NB-95 RU-1 03 RU-1 06 1.65E+08 5.24E+08 2.37E+08 0.OOE+00 3.12E+08 1.45E+08 3.05E+09 0.00E+00 8.76E+07 9.84E+10 0.00E+00 2.41E+10 1.03E+03 0.00E+00 2.76E+01 1.13E+02 3.63E+01 2.46E+01 9.92E+03 5.52E+03 2.97E+03 1.22E+02 0.00E+00 5.27E+01 2.45E+03 0.00E+00 3.10E+02 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 3.51 E+08 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 3.30E+08 6.14E+07 4.89E+08 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 5.70E+01 0.OOE+00 5.45E+03 0.OOE+00 4.67E+02 0.OOE+00 4.73E+03 0.OOE+00 2.84E+09 5.68E+05 1.15E+05 3.35E+07 1.43E+04 1.59E+05 2.64E+09 7.81 E+06 1.84E+07 3.64E+07 1.34E+08 7.28E+06 AG-110M 6.99E+06 6.47E+06 TE-125M 1.96E+06 7.09E+05 TE-127M 5.50E+06 1.97E+06 TE-129M 7.23E+06 2.70E+06 1-131 3.56E+08 5.09E+08 1-133 4.65E+06 8.10E+06 CS-134 1.70E+10 4.04E+10 CS-136 7.92E+08 3.13E+09 CS-1 37 2.22E+10 3.03E+10 3.84E+06 0.00E+00 1.27E+07 2.62E+05 5.89E+05 7.96E+06 6.70E+05 1.41E+06 2.23E+07 1.14E+06 2.48E+06 3.02E+07 2.92E+08 1.67E+ 1I 8.73E+08 2.47E+06 1.19E+09 1.41E+07 3.30E+10 0.00E+00 1.31E+10 2.25E+09 0.00E+00 1.74E+09 1.99E+10 0.00E+00 1.03E+10 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.00E+00 0.00E+00 4.34E+09 2.38E+08 3.42E+09 7.07E+08 3.55E+08 5.87E+08 BA-140 3.24E+06 4.07E+03 2.12E+05 0.OOE+00 1.38E+03 2.33E+03 6.67E+06 CE-141 5.82E+02 3.94E+02 4.47E+01 0.00E+00 1.83E+02 0.OOE+00 1.51E+06 CE-144 4.30E+04 1.80E+04 2.31E+03 0.00E+00 1.07E+04 0.OOE+00 1.45E+07 PR-143 1.90E+01 7.60E+00 9.40E-01 0.00E+00 4.39E+00 0.OOE+00 8.30E+04 ND-147 1.13E+01 1.31E+01 7.82E-01 0.OOE+00 7.65E+00 0.OOE+00 6.28E+04 CY-TM-170-300 Revision 3 Page 157 of 209 TABLE 5.6.1 Pathway Dose Factors, R 1 AGE GROUP: INFANT PATHWAY: GRASS-COW-MEAT NUCLIDE ORGAN DOSE FACTORS; M -mrem/year per piCisec SIBONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 C-14 CR-51 MN-54 FE-55 FE-59 CO-58 CO-60 NI-63 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00---

0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00----- ---+ --0 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 ZN-65 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 RB-86 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 SR-89 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 SR-90 Y-91 ZR-95 NB-95 RU-103 RU-106 AG-110M TE-125M TE-127M TE-129M 1-131 1-133 CS-1 34 CS-136 CS-137 BA-140 CE-141 CE-144 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00.................................................

0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 0O.E+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 PR-1 43 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 ND-147 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 CY-TM-1 70-300 Revision 3 Page 158 of 209 TABLE 5.6.2 Pathway Dose Factors, R, AGE GROUP: CHILD PATHWAY: GRASS-COW-MEAT

[ULD ------ ORGAN DOSE FAC NULD-----------------------------

j BONE LIVER T.BODY H-3 0.OOE+00 2.34E+02 2.34E+02 C-14 3.84E+08 7.67E+07 7.67E+07 CR-51 0.OOE+00 O.00E+00 8.78E+03 MN-54 0.OOE+00 8.01E+06 2.13E+06 FE-55 4.57E+08 2.43E+08 7.52E+07 FE-59 3.77E+08 6.10E+08 3.04E+08 CO-58 0.00E+00 1.64E+07 5.03E+07 CO-60 0.00E+00 6.93E+07 2.04E+08 NI-63 2.91E+10 1.56E+09 9.91E+08.......................................

ZN-65 3.76E+08 1.OOE+09 6.22E+08 RB-86 0.00E+00 5.76E+08 3.54E+08 SR-89 4.82E+08 0.OOE+00 1.38E+07 SR-90 1.04E+10 O.OOE+00 2.64E+09 Y-91 1.80E+06 0.OOE+00 4.82E+04 ZR-95 2.66E+06 5.86E+05 5.21E+05 TORS; mrem/year per iiCi/sec THYROID KIDNEY LUNG GI-LLI 2.34E+02 2.34E+02 2.34E+02 2.34E+02 7.67E+07 7.67E+07 7.67E+07 7.67E+07 4.88E+03 1.33E+03 8.90E+03 4.66E+05 0.OOE+00 2.25E+06 0.00E+00 6.73E+06 O.OOE+00 O.00E+00 1.37E+08 4.49E+07 O.00E+00 O.00E+00 1.77E+08 6.35E+08 0.00E+00 O.00E+00 O.00E+00 9.58E+07 O.00E+00 O.00E+00 0.OOE+00 3.84E+08 O.00E+00 O.OOE+00 O.00E+00 1.05E+08 0.00E+00 6.31E+08 O.OOE+00 1.76E+08 O.00E+00 0.OOE+00 O.00E+00 3.71E+07 0.00E+00 0.OOE+00 O.OOE+00 1.87E+07 O.00E+00 0.OOE+00 0.0OE+00 1.40E+08 0.00E+00 0.OOE+00 O.OOE+00 2.40E+08 0.00E+00 8.38E+05 0.OOE+00 6.11E+08 NB-95 RU-1 03 RU-106 AG-11iM TE-125M.TE-127M TE-129M 1-131 1-133 CS-1 34 CS-1 36 CS-1 37 BA-140 CE-141 CE-144 3.1OE+06 1.21E+06 8.63E+05 1.55E+08 0.OOE+00 5.96E+07 4.44E+09 0.OOE+00 5.54E+08 0.OOE+00 1.13E+06 0.OOE+00 3.90E+08 0.00E+00 6.OOE+09 8.39E+06 5.67E+06 4.53E+06 0.OOE+00 5.69E+08 1.54E+08 7.59E+07 1.60E+08 1.78E+09 4.78E+08 2.11E+08 4.25E+08 1.79E+09 5.OOE+08 2.78E+08 5.77E+08 1.66E+07 1.67E+07 9.48E+06 5.52E+09 5.72E-01 7.08E-01 2.68E-01 1.31 E+02 9.23E+08 1.51E+09 3.19E+08 O.OOE+00 1.63E+07 4.48E+07 2.90E+07 0.00E+00 1.33E+09 1.28E+09 1.89E+08 0.OOE+00 4.42E+07 3.87E+04 2.58E+06 0.OOE+00 2.22E+04 1.11 E+04 1.65E+03 0.OOE+00 2.32E+06 7.26E+05 1.24E+05 0.OOE+00 1.06E+07 0.OOE+00 5.06E+09 5.26E+09 2.74E+07 1.18E+00 4.69E+08 2.39E+07 4.16E+08 1.26E+04 4.86E+03 4.02E+05 0.OOE+00 2.23E+09 0.00E+00 4.01E+09 0.OOE+00 6.91E+10 0.00E+00 6.74E+08 0.OOE+00 5.49E+08 0.00E+00 1.44E+09 0.OOE+00 2.18E+09 0.00E+00 1.48E+06 0.OOE+00 2.85E-01 1.68E+08 8.16E+06 3.56E+06 1.57E+06 1.50E+08 8.OOE+06 2.31 E+04 0.00E+00 0.00E+00 2.24E+07 1.38E+07 1.89E+08 PR-143 3.33E+04 1.00E+04 1.65E+03 0.OOE+00 5.42E+03 0.00E+00 3.60E+07 ND-147 1.17E+04 9.48E+03 7.34E+02 0.OOE+00 5.20E+03 0.00E+00 1.50E+07 CY-TM-1 70-300 Revision 3 Page 159 of 209 TABLE 5.6.3 Pathway Dose Factors, R, AGE GROUP: TEEN PATHWAY: GRASS-COW-MEAT NUCLIDE ORGAN DOSE FACTORS; m 2 -mrem/year per !tCi/sec_ BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 0.OOE+00 C-14 2.04E+08 CR-51 0.OOE+00 MN-54 0.00E+00 FE-55 2.38E+08 FE-59 2.12E+08 CO-58 0.OOE+00 CO-60 0.OOE+00 NI-63 1.52E+10 ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 NB-95 RU-103 RU-106 AG-11OM TE-125M TE-127M 2.50E+08 0.00E+00 2.55E+08 8.04E+09 9.54E+05 1.50E+06 1.79E+06 8.56E+07 2.36E+09 5.06E+06 3.03E+08 9.41 E+08 1.93E+02 1.93E+02 4.08E+07 4.08E+07 0.OOE+00 5.63E+03 7.OOE+06 1.39E+06 1.69E+08 3.94E+07 4.95E+08 1.91 E+08 1.40E+07 3.24E+07 5.83E+07 1.31E+08 1.07E+09 5.15E+08---------..----------

8.68E+08 4.05E+08 4.06E+08 1.91E+08 0.OOE+00 7.29E+06 0.00E+00 1.99E+09 0.OOE+00 2.56E+04 4.73E+05 3.25E+05---------------------

9.95E+05 5.48E+05 0.00E+00 3.66E+07 0.OOE+00 2.97E+08 4.78E+06 2.91 E+06 1.09E+08 4.05E+07 3.34E+08 1.12E+08 1.93E+02 1.93E+02 1.93E+02 4.08E+07 4.08E+07 4.08E+07 3.13E+03 1.23E+03 8.03E+03 0.00E+00 2.09E+06 0.OOE+00 0.OOE+00 0.OOE+00 1.07E+08 0.OOE+00 0.OOE+00 1.56E+08 0.00E+00 0.00E+00 0.00E÷00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 5.56E+08 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.56E+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 6.95E+05 0.00E+00 1.93E+02 4.08E+07 9.46E+05 1.44E+07 7.31 E+07 1 .17E+09 1.94E+08 7.60E+08 1.71 E+08 3.68E+08 6.OOE+07 3.03E+07 2.26E+08 3.91 E+08 1.09E+09 4.25E+09 7.15E+09 1.13E+11 1.34E+09 8.94E+08 2.35E+09 3.56E+09 2.47E+06 3.95E-01 1.53E+07 2.99E+06 1.37E+07 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 8.46E+07 2.24E+08 9.64E+05 0.OOE+00 3.02E+08 0.OOE+00 4.54E+09 0.OOE+00 9.13E+06 0.00E+00 0.OOE+00 0.OOE+00 3.81E+09 0.OOE+00 TE-129M 9.49E+08 1-131 8.93E+06 1-133 3.08E-01 CS-1 34 5.23E+08 CS-1 36 9.43E+06 CS-1 37 7.24E+08 3.52E+08 1.25E+07 5.22E-01 1.23E+09 3.71 E+07 9.63E+08 1.50E+08 6.72E+06 1.59E-01 5.71 E+08 2.49E+07 3.35E+08 3.06E+08 3.65E+09 7.29E+01 0.00E+00 0.OOE+00 0.OOE+00 3.97E+09 2.15E+07 9.16E-01 3.91 E+08 2.02E+07 3.28E+08 0.OOE+00 0.OOE+00 0.00E+00 1.49E+08 3.18E+06 1 .27E+08 BA-140 2.39E+07 2.93E+04 1.54E+06 0.OOE+00 9.94E+03 1.97E+04 3.69E+07 CE-141 1.18E+04 7.87E+03 9.05E+02 0.OOE+00 3.71E+03 0.OOE+00 2.25E+07 CE-144 1.23E+06 5.08E+05 6.60E+04 0.OOE+00 3.03E+05 0.OOE+00 3.09E+08 PR-143 1.76E+04 7.03E+03 8.76E+02 ND-147 6.23E+03 6.78E+03 4.06E+02 0.OOE+00 4.08E+03 0.OOE+00 5.79E+07 0.OOE+00 3.98E+03 0.OOE+00 2.44E+07 CY-TM-1 70-300 Revision 3 Page 160 of 209 TABLE 5.6.4 Pathway Dose Factors, R, AGE GROUP: ADULT PATHWAY: GRASS-COW-MEAT NUCLIDE ORGAN DOSE FACTORS; m _ mrem/year per _Ci/_sec ( BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 0.OOE+00 3.24E+02 3.24E+02 3.24E+02 3.24E+02 3.24E+02 3.24E+02 C-14 2.42E+08 4.83E+07 4.83E+07 4.83E+07 4.83E+07 4.83E+07 4.83E+07 CR-51 0.OOE+00 O.OOE+00 7.04E+03 4.21E+03 1.55E+03 9.35E+03 1.77E+06................................................................................

MN-54 FE-55 FE-59 CO-58 CO-60 NI-63 ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 0.OOE+00 9.18E+06 2.93E+08 2.03E+08 2.66E+08 6.25E+08.....................

0.OOE+00 1.82E+07 O.OOE+00 7.52E+07 1.89E+10 1.31E+09---------------------

3.56E+08 1.13E+09 0.OOE+00 4.87E+08 3.02E+08 O.OOE+00 1.24E+10 O.OOE+00 1.13E+06 0.OOE+00 1.87E+06 6.01E+05 1.75E+06 0.OOE+00 4.73E+07 0.OOE+00 2.39E+08 O.OOE+00-.-------------------

4.09E+07 0.OOE+00 1.66E+08 0.OOE+00 6.33E+08 0.OOE+00-.-------------------

5.12E+08 O.OOE+00 2.27E+08 0.OOE+00.8.66E+06 O.OOE+00 3.05E+09 0.OOE+00 3.03E+04 0.OOE+00 4.07E+05 O.OOE+00 6.87E+05 0.OOE+00 4.53E+07 0.OOE+00 3.54E+08 O.OOE+00-.-------------------

3.67E+06 0.OOE+00 4.81 E+07 1.08E+08 1.36E+08 2.85E+08 2.73E+06 0.OOE+00 2.81E+07 0.OOE+00 1.13E+08 1.16E+08 0.OOE+00 1.75E+08 2.08E+09...............................

O.OOE+00 0.OOE+00 3.70E+08 0.OOE+00 0.OOE+00 1.41 E+09 0.OOE+00 0.OOE+00 2.73E+08 7.57E+08 O.OOE+00 7.13E+08 0.OOE+00 0.OOE+00 9.59E+07 0.OOE+00 0.OOE+00 4.84E+07 0.OOE+00 0.OOE+00 9.43E+05 O.OOE+O0 0.OOE+00 O.OOE+00 3.60E+08 6.24E+08 1.90E+09 NB-95 2.30E+06 1.28E+06 RU-103 1.05E+08 0.OOE+00 RU-106 2.80E+09 0.OOE+00............................

AG-110M 6.68E+06 6.18E+06 TE-125M 3.59E+08 1.30E+08 TE-127M 1.12E+09 3.99E+08 1.26E+06 O.OOE+00 4.02E+08 0.OOE+00 5.41E+09 0.OOE+00 1.22E+07 0.OOE+00 1.46E+09 0.OOE+00 4.53E+09 0.OOE+00 TE-129M 1-131 1-133 CS-1 34 CS-1 36 CS-1 37 1.13E+09 1.08E+07 3.68E-01 6.58E+08 1.21E+07 8.72E+08 2.90E+07 1.41 E+04 1.46E+06 4.23E+08 1.54E+07 6.41 E-01 1.57E+09 4.78E+07 1.19E+-09 3.64E+04 9.51 E+03 6.1OE+05 1.79E+08 3.89E+08 8.82E+06 5.04E+09 1.95E-01 9.42E+01 1.28E+09 0.OOE+00 3.44E+07 0.OOE+00 7.82E+08 O.OOE+00 4.73E+09 0.OOE+00 2.64E+07 0.OOE+00 1.12E+00 0.OOE+00 5.07E+08 1.68E+08 2.66E+07 3.65E+06 4.05E+08 1.35E+08 1.24E+04 2.08E+04 4.42E+03 O.OOE+00 3.62E+05 0.OOE+00 7.76E+09 1.23E+10 1.81 E+I 1 2.52E+09 1.43E+09 3.74E+09 5.71 E+09 4.06E+06 5.76E-01 2.74E+07 5.43E+06 2.31E+07 5.96E+07 3.64E+07 4.93E+08 BA-140 CE-141 CE-144 1.90E+06 1.08E+03 7.83E+04 O.OOE+00 0.OOE+00 O.OOE+00 PR-143 2.09E+04 8.40E+03 1.04E+03 O.OOE+00 4.85E+03 O.OOE+00 9.17E+07 ND-147 7.08E+03 8.18E+03 4.90E+02 0.OOE+00 4.78E+03 0.OOE+00 3.93E+07 CY-TM-1 70-300 Revision 3 Page 161 of 209 TABLE 5.7.1 Pathway Dose Factors, R, AGE GROUP: INFANT PATHWAY: VEGETATION NUCLIDE ORGAN DOSE FACTORS; m2 -mrem/year per piCi/sec-BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 0.OOE+00 C-14 O.OOE+00 CR-51 0.00E+00 MN-54 0.00E+00 FE-55 0.00E+00 FE-59 O.OOE+00 CO-58 0.OOE+00 CO-60 0.00E+00 NI-63 0.OOE+00 ZN-65 0.OOE+00 RB-86 0.OOE+00 SR-89 0.OOE+00 0.O0E+00 O.OOE+00 O.00E+00 O.OOE+00 0.00E+00 0.00E+00 O.OOE+00 O.OOE+00 0.OOE+00 O.OOE+00 O.OOE+00 O.OOE+00 O.OOE+00 O.OOE+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 O.OOE+00 O.OOE+00 O.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 O.OOE+00 O.OOE+00 O.OOE+00 O.OOE+00 O.00E+00 O.00E+00 Q.OOE+00 O.OOE+00 O.OOE+OO 0.00E+O0 O.00E+00 O.OOE+00 0.OOE+00 O.OOE+0O 0.00E+0O O.OOE+00 0.OOE+0O O.OOE+00 0.OOE+0O 0.OOE+00 O.OOE+00 O.OOE+00 0.OOE+00 0.OOE+00 O.00E+00 0.OOE+00 O.OOE+00 0.00E+00 0.00E+00 O.OOE+00 0.00E+00 O.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 O.OOE+00 O.00E+00 0.OOE+OO O.OOE+00 0.00E+00 0.OOE+00 O.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 O.OOE+00 O.OOE+O0 0.OOE+OO O.OOE+OO--

O.OOE+00 0.OOE+0O O.OOE+00 O.OOE+00 O.OOE+00 O.OOE+OO 0.OOE+00 0.OOE+00 O.OOE+0O 0.00 E+00--0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 SR-90 Y-91 ZR-95 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 O.OOE+00 0.00E+00 O.00E+O0 NB-95 0.00E+00 RU-1 03 0.OOE+00 RU-1 06 O.00E+00 AG-110M 0.OOE+00 TE-125M 0.00E+00 TE-127M 0.00E+00 0.00E+00 0.OOE+00 0.00E+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 O.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 TE-129M 1-131 1-133 CS-1 34 CS-1 36 CS-137 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.00E+00 0.00E+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.00E+00 0.OOE+O0 0.OOE+00 0.00E+00 0.OOE+00 0:OOE+00 0.00E+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 BA-140 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 CE-141 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 CE-1 44 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 PR-143 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 ND-147 0.00E+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 CY-TM-1 70-300 Revision 3 Page 162 of 209 TABLE 5.7.2 Pathway Dose Factors, R, AGE GROUP: CHILD PATHWAY: VEGETATION N ORGAN DOSE FACTORS; m2 -mrem/year per ipCi/sec NUCLI BONE LIVER T.BODY THYROID KIDNEY LUNG GI-LLI H-3 C-14 CR-51 MN-54 FE-55 FE-59 CO-58 CO-60 NI-63 ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 NB-95 RU-103 RU-106 0.OOE+00 4.02E+03 4.02E+03 8.89E+08 1.78E+08 1.78E+08 0.OOE+00 0.00E+00 1.17E+05...............................

O.OOE+00 6.65E+08 1.77E+08 8.01 E+08 4.25E+08 1.32E+08 3.98E+08 6.44E+08 3.21E+08 0.00E+00 6.44E+07 1.97E+08 0.00E+00 3.78E+08 1.12E+09 3.95E+10 2.11E+09 1.34E+09-------------------------------

8.12E+08 2.16E+09 1.35E+09 0.00E+00 4.51E+08 2.77E+08 3.60E+10 0.OOE+00 1.03E+09---------------------.---------

1.24E+12 O.OOE+00 3.15E+11 1.87E+07 0.OOE+00 4.99E+05 3.86E+06 8.48E+05 7.55E+05 4.02E+03 1 .78E+08 6.49E+04--.--E+---0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 O.00E+00 0.00E+00 0.OOE+00 4.02E+03 1.78E+08 1.77E+04 1.86E+08 0.OOE+00 O.00E+00 0.00E+00 0.OOE+00 0.00E+00 1.36E+09 0.OOE+00 0.OOE+00 4.02E+03 4.02E+03 1.78E+08 1.78E+08 1.18E+05 6.20E+06......................

0.00E+00 5.58E+08 2.40E+08 7.87E+07 1.87E+08 6.71E+08 0.OOE+00 3.76E+08 0.00E+00 2.10E+09 0.00E+00 1.42E+08...E..................

0.00E+00 3.80E+08 0.00E+00 2.90E+07 0.00E+00 1.39E+09......................

0.00E+00 1.67E+10 0.OOE+00 2.49E+09 0.OOE+00 8.85E+08...E..................

0.OOE+00 2.96E+08 0.00E+00 3.97E+08 0.OOE+00 1.16E+10......................

0.00E+00 2.58E+09 0.00E+00 3.38E+08 0.00E+00 1.07E+09 0.00E+00 1.02E+09 0.OOE+00 1.28E+07 0.00E+00 1.76E+06 4.11E+05 1.53E+07 7.45E+08 1.60E+05 0.OOE+00 0.OOE+00 1.14E+05 5.90E+06 9.30E+07 0.00E+00 0.OOE+00 0.OOE+00--.---+--0.OOE+00 0.OOE+00 0.OOE+00 9.84E+07 3.16E+08 2.71 E+08 4.76E+1 0 8.12E+08 0.00E+00 0.00E+00 1.21 E+06 1.50E+05 3.86E+07 1.01E+09 4.04E+07 0.00E+00 3.77E+09 2.47E+09 2.36E+08 7.28E+06 AG-110M 3.21E+07 2.17E+07 1.73E+07 TE-125M 3.51E+08 9.50E+07 4.67E+07 TE-127M 1.32E+09 3.56E+08 1.57E+08 TE-129M 8.40E+08 2.35E+08 1.30E+08 1-131 1.43E+08 1.44E+08 8.18E+07 1-133 3.53E+06 4.37E+06 1.65E+06 CS-134 1.60E+10 2.63E+10 5.55E+09 0.00E+00 8.15E+09 2.93E+09 1.42E+08 CS-136 8.28E+07 2.28E+08 1.47E+08 0.00E+00 1.21E+08 1.81E+07 8.OOE+06 CS-137 2.39E+10 2.29E+10 3.38E+09 0.OOE+00 7.46E+09 2.68E+09 1.43E+08 BA-140 2.79E+08 2.44E+05 1.63E+07 0.00E+00 7.96E+04 1.46E+05 1.41E+08 CE-141 6.57E+05 3.28E+05 4.86E+04 0.00E+00 1.44E+05 0.00E+00 4.09E+08 CE-144 1.27E+08 3.99E+07 6.79E+06 0.00E+00 2.21E+07 0.00E+00 1.04E+10 PR-143 1.45E+05 4.36E+04 7.21E+03 ND-147 7.15E+04 5.79E+04 4.49E+03 0.OOE+00 2.36E+04 0.00E+00 1.57E+08 0.00E+00 3.18E+04 0.00E+00 9.18E+07 CY-TM-1 70-300 Revision 3 Page 163 of 209 TABLE 5.7.3 Pathway Dose Factors, R, AGE GROUP: TEEN PATHWAY: VEGETATION NUCL-DE [ -- ORGAN DOSE FACTORS; m 2 -mrem/year per --Ci/sec NUCLIDE LIV E TO RO-D K eY LUNG -- L-___ _ ___-___ _ BONE -_ -LIVER -_ T.BODY --THYROID --KIDNEY -LUNG- .GI-LLI--H-3 C-14 CR-51 MN-54 FE-55 FE-59 O.OOE+00 2.59E+03 2.59E+03 3.69E+08 7.38E+07 7.38E+07 0.OOE+00 0.OOE+00 6.16E+04 0.OOE+00 4.54E+08 9.01E+07 3.26E+08 2.31E+08 5.39E+07 1.80E+08 4.19E+08 1.62E+08 2.59E+03 7.38E+07 3.42E+04--.-OE+--O.OOE+00 0.OOE+00 2.59E+03 7.38E+07 1.35E+04 1.36E+08 0.OOE+00 0.OOE+00 2.59E+03 2.59E+03 7.38E+07 7.38E+07 8.79E+04 1.03E+07 0.OOE+00 9.32E+08 1.47E+08 1.OOE+08 1.32E+08 9.91E+08......................

0.OOE+00 6.01E+08 0.OOE+00 3.24E+09 0.00E+00 1.81E+08 CO-58 0.OOE+00 4.36E+07 1.01E+08 0.OOE+00 0.OOE+00 CO-60 0.OOE+00 2.49E+08 5.60E+08 0.OOE+00 0.OOE+00 NI-63 1.61E+10 1.13E+09 5.45E+08 0.OOE+00 0.OOE+00 ZN-65 RB-86 SR-89 SR-90 Y-91 ZR-95 NB-95 RU-103 RU-106 4.24E+08 0.OOE+00 1.52E+10 7.51E+11 7.84E+06 1.72E+06 1.92E+05 6.82E+06 3.09E+08 1.47E+09 2.73E+08 0.OOE+00 6.86E+08 1.28E+08 4.34E+08 0.OOE+00 1.85E+11 0.OOE+00 2.10E+05 5.43E+05 3.73E+05 1.07E+05 5.87E+04 0.OOE+00 2.92E+06 O.OOE+00 3.90E+07 1 .43E+07 8.72E+06 5.34E+07 1.98E+07 1.96E+08 6.56E+07 1.34E+08 5.72E+07 1.08E+08 5.78E+07 3.29E+06 1.OOE+06 0.OOE+00 9.42E+08 0.OOE+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.00E+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 7.98E+05 0.OOE+00 0.OOE+00 1.03E+05 0.OOE+00 0.OOE+00 2.41E+07 0.OOE+00 0.OOE+00 5.97E+08 0.OOE+00 0.OOE+00 2.74E+07 0.OOE+00 4.14E+07 0.OOE+00 0.00E+00 1.31E+08 2.24E+09 0.OOE+00 1.17E+08 1.51E+09 0.OOE+00 3.14E+10 1.85E+08 0.00E+00 4.59E+08 5.77E+06 0.OOE+00 0.OOE+00 5.31E+09 2.03E+09 0.OOE+00 9.41 E+07 1.48E+07 0.OOE+00 4.59E+09 1.78E+09 6.23E+08 4.04E+07 1.80E+09 2.11E+10 3.22E+09 1.25E+09 4.56E+08 5.70E+08 1.48E+10 4.03E+09 4.37E+08 1.37E+09 1.36E+09 2.13E+07 2.49E+06 2.08E+08 1 .39E+07 1.92E+08 AG-110M TE-125M TE-127M TE-129M 1-131 1-133 1.52E+07 1.48E+08 5.52E+08 3.61 E+08 7.69E+07 1.94E+06 7.1OE+09 4.39E+07 1.01E+10 CS-1 34 CS-1 36 CS-1 37 1.67E+10 1.73E+08 1.35E+10 7.75E+09 1. 16E+08 4.69E+09 BA-140 1.39E+08 1.71E+05 8.97E+06 0.OOE+00 5.78E+04 1.15E+05 2.15E+08 CE-141 2.83E+05 1.89E+05 2.17E+04 0.OOE+00 8.90E+04 0.OOE+00 5.41E+08 CE-144 5.28E+07 2.18E+07 2.83E+06 0.00E+00 1.30E+07 0.OOE+00 1.33E+10 PR-143 6.99E+04 2.79E+04 3.48E+03 0.OOE+00 1.62E+04 0.OOE+00 2.30E+08 ND-147 3.62E+04 3.94E+04 2.36E+03 0.OOE+00 2.31E+04 O.OOE+00 1.42E+08 CY-TM-1 70-300 Revision 3 Page 164 of 209 TABLE 5.7.4 Pathway Dose Factors, R, AGE GROUP: ADULT PATHWAY: VEGETATION SORGAN DOSE FACTORS; M 2-mrem/year per GCi-sec__~ ~ ___ __ __ __ BONE -_ -LIVER T.BODY --THYROID --KIDNEY -LUNG- .GI-LLI_H-3 0.OOE+00 C-14 2.28E+08 CR-51 O.OOE+00 MN-54 0.OOE+00 FE-55 2.1OE+08 FE-59 1.26E+08 CO-58 0.OOE+00 CO-60 0.OOE+00 NI-63 1.04E+10 ZN-65 3.17E+08 RB-86 0.OOE+00 SR-89 9.98E+09 SR-90 6.05E+11 Y-91 5.12E+06 ZR-95 1.17E+06 NB-95 1.42E+05 RU-1 03 4.77E+06 RU-106 1.93E+08 AG-110M 1.05E+07 TE-125M 9.66E+07 TE-127M 3.49E+08 TE-129M 2.51E+08 1-131 8.08E+07 1-133 2.09E+06 CS-1 34 4.67E+09 CS-1 36 4.28E+07 CS-1 37 6.36E+09 2.26E+03 2.26E+03 4.55E+07 4.55E+07 O.OOE+00 4.64E+04-----------.----------

3.13E+08 5.97E+07 1.45E+08 3.38E+07 2.97E+08 1.14E+08 3.07E+07 6.89E+07 1.67E+08 3.69E+08 7.21 E+08 3.49E+08-----------.----------

1.01E+09 4.56E+08 2.19E+08 1.02E+08 0.OOE+00 2.86E+08......................

0.OOE+00 1.48E+1 1 0.OOE+00 1.37E+05 3.77E+05 2.55E+05-----------.----------

7.92E+04 4.26E+04 0.OOE+00 2.06E+06 O.OOE+00 2.44E+07 9.75E+06 5.79E+06 3.50E+07 1.29E+07 1.25E+08 4.26E+07-----------.----------

9.37E+07 3.97E+07 1.16E+08 6.62E+07 3.63E+06 1.11E+06 1.11E+10 9.08E+09 1.69E+08 1.22E+08 8.70E+09 5.70E+09 2.26E+03 4.55E+07 2.77E+04 0.OOE+0O 0.OOE+00 0.OOE+O0 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 O.OOE+00 O.OOE+00 O.OOE+0O 0.OOE+0O O.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 0.OOE+00 2.90E+07 8.93E+07 8.63E+07 3.79E+1 0 5.34E+08 0.OOE+00 0.OOE+00 0.OOE+00 2.26E+03 2.26E+03 2.26E+03 4.55E+07 4.55E+07 4.55E+07 1.02E+04 6.15E+04 1.17E+07---------------------.----------

9.31E+07 0.OOE+00 9.58E+08 0.OOE+00 8.08E+07 8.31E+07 0.OOE+00 8.29E+07 9.89E+08 O.OOE+00 0.OOE+00 6.23E+08 0.OOE+00 0.OOE+00 3.14E+09 0.OOE+00 O.OOE+00 1.50E+08---------------------.----------

6.75E+08 O.OOE+00 6.36E+08 0.OOE+00 0.OOE+00 4.32E+07 0.OOE+00 0.OOE+00 1.60E+09 0.OOE+00 0.OOE+00 1.75E+10 0.OOE+00 0.OOE+00 2.82E+09 5.91E+05 O.OOE+00 1.19E+09 7.83E+04 0.OOE+00 4.81E+08 1.82E+07 O.OOE+00 5.57E+08 3.72E+08 0.OOE+00 1.25E+10 1.92E+07 0.OOE+00 3.98E+09 3.93E+08 0.OOE+00 3.86E+08 1.42E+09 0.OOE+00 1.17E+09 1.05E+09 O.OOE+00 1.26E+09 1.98E+08 0.OOE+00 3.05E+07 6.33E+06 0.OOE+00 3.26E+06---------------------.----------

3.59E+09 1.19E+09 1.94E+08 9.41E+07 1.29E+07 1.92E+07 2.95E+09 9.81E+08 1.68E+08 BA-140 1.29E+08 1.62E+05 8.47E+06 O.OOE+00 5.52E+04 9.29E+04 2.66E+08 CE-141 1.97E+05 1.33E+05 1.51E+04 0.00E+00 6.20E+04 0.OOE+00 5.10E+08 CE-144 3.29E+07 1.38E+07 1.77E+06 O.OOE+00 8.16E+06 0.OOE+00 1.11E+10 PR-143 6.25E+04 2.51E+04 ND-147 3.34E+04 3.85E+04 3.10E+03 O.OOE+00 1.45E+04 0.OOE+00 2.74E+08 2.31E+03 O.OOE+00 2.25E+04 0.OOE+00 1.85E+08 CY-TM-1 70-300 Revision 3 Page 165 of 209 6.0 TMI-1 GASEOUS EFFLUENT WASTE TREATMENT SYSTEM 6.1 Description of the TMI-1 Gaseous Radwaste Treatment System (see Figure 6.1)6.1.1 Waste Gas System a. Reactor Building:-Reactor Coolant Drain Tank (RCDT) header b. Auxiliary Building:-Vent Header from 1. Miscellaneous Waste Storage Tank (MWST)2. Three (3) Reactor Coolant Bleed Tanks (RCBT)-Waste Gas Delay Tank-Two (2) Waste Gas Compressors

-Three (3) Waste Gas Decay Tanks (WGDT)c. Filtration and dilution provided by the Station Ventilation System.6.2 Operability of the TMI-1 Gaseous Radwaste Treatment System Operability of the Gaseous Waste Treatment System is defined as the ability to remove gas from the vent header/tank gas spaces and store it under a higher pressure in the Waste Gas Decay Tanks for subsequent release.Except for initiating the make up tank sample and waste gas venting and the recycle or disposal of compressed waste gases stored in the waste gas decay tanks, the operation of the waste gas system is entirely automatic.

One waste gas compressor comes on automatically, removing gases from the vent header system as required, to maintain the pressure in the system at a maximum of about 16.4 psia.

CY-TM-1 70-300 Revision 3 Page 166 of 209 FIGURE 6.1 Waste Gas System Ad LawpI -"Mi a___L CY-TM-1 70-300 Revision 3 Page 167 of 209 7.0 EFFLUENT TOTAL DOSE ASSESSMENT 7.1 Total Dose Calculation The annual (calendar year) dose or dose commitment to any member of the public, due to releases of radioactivity and to radiation from uranium fuel cycle sources shall be limited to less than or equal to 25 mrem to the total body or any organ except the thyroid, which shall be limited to less than or equal to 75 mrem.This control is provided in order to meet the dose limitations of 40 CFR 190.The total dose from TMI-1 and TMI-2 (uranium fuel cycle facilities within 8 kilometers) is calculated by summing the calculated annual doses to critical organs of a real individual for liquid effluent using Section 2.1 methodology, for gaseous effluent using Section 5.2.1 and 5.2.2 methodology, and the direct radiation from the site from the environmental monitoring program's direct radiation monitors.

CY-TM-170-300 Revision 3 Page 168 of 209 8.0 TMINS RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM (REMP)8.1 Monitorinq Program Requirements 8.1.1 Controls In accordance with the TMI-1 Tech. Specs. and TMI -2 PDMS Tech.Specs., the radiological environmental monitoring program shall be conducted as specified in Table 8.1.8.1.2 Applicability At all times.8.1.3 Action a. With the radiological environmental monitoring program not being conducted as specified in Table 8.1, prepare and submit to the Commission in the Annual Radiological Environmental Operating Report, a description of the reasons for not conducting the program as required and the plans for preventing a recurrence.

b. With the level of radioactivity as the result of plant effluents in an environmental sampling medium exceeding the reporting levels of Table 8.2 when averaged over any calendar quarter, prepare and submit to the Commission within 30 days from the end of the affected calendar quarter, a special report that identifies the cause(s) for exceeding the limit(s) and defines the corrective actions to be taken to reduce radioactive effluents so that the potential annual dose to a member of the public is less than the calendar year limits of ODCM Part I Controls 2.2.1.2, 2.2.2.2 and 2.2.2.3 and ODCM Part II Controls 2.2.1.2, 2.2.2.2 and 2.2.2.3. When more than one of the radionuclides in Table 8.2 are detected as the result of plant effluents in the sampling medium, this report shall be submitted if: concentration (1) concentration (2) + > 1.0 reportinglevel (1) reporting level (2) +When radionuclides other than those in Table 8.2 are detected and are the result of plant effluents, this report shall be The methodology and parameters used to estimate the potential annual dose to a member of the public shall be indicated in this report.

CY-TM-1 70-300 Revision 3 Page 169 of 209 submitted if the potential annual dose* to a member of the public is equal to or greater than the calendar year limits of ODCM Part I Controls 2.2.1.2, 2.2.2.2 and 2.2.2.3 and ODCM Part II, Controls 2.2.1.2, 2.2.2.2 and 2.2.2.3. This report is not required if the measured level of radioactivity was not the result of plant effluents; however, in such an event, the condition shall be reported and described in the Annual Radiological Environmental Operating Report.c. With milk or fresh leafy vegetation samples unavailable from one or more of the sample locations required by Table 8.1, identify specific locations for obtaining replacement samples and add them within 30 days to the Radiological Environmental Monitoring Program given in the ODCM. The specific locations from which samples were unavailable may then be deleted from the monitoring program. Pursuant to TMI-1 Tech. Spec. 6.14 and TMI-2 PDMS Tech. Spec. 6.12, submit in the next Annual Radioactive Effluent Release Report documentation for a change in the ODCM including a revised figure(s) and table for the ODCM reflecting the new location(s) with supporting information identifying the cause of the unavailability of samples and justifying the selection of the new location(s) for obtaining samples.8.1.4 Bases The radiological monitoring program required by this control provides representative measurements of radiation and of radioactive materials in those exposure pathways and for those radionuclides which lead to the highest potential radiation exposures of members of the general public resulting from the station operation.

This monitoring program implementsSection IV B.2 of Appendix I to 10CFR50 and thereby supplements the radiological effluent monitoring program by verifying that the measurable concentrations of radioactive materials and levels of radiation are not higher than expected on the basis of the effluent measurements and modeling of the environmental exposure pathways.Guidance for this monitoring is provided by the Radiological Assessment Branch Technical Position on Environmental Monitoring (Revision 1, November 1979). Program changes may be initiated based on operational experience.

8.1.5 Surveillance Requirements The radiological environmental monitoring samples shall be collected pursuant to Table 8.1, from the specific locations given in Tables 8.4 through 8.10 and Maps 8.1 through 8.3, and shall be analyzed pursuant CY-TM-170-300 Revision 3 Page 170 of 209 to the requirements of Table 8.1 and the detection capabilities required by Table 8.3.

CY-TM-170-300 Revision 3 Page 171 of 209 8.2 Land Use Census 8.2.1 Controls In accordance with the TMI-1 Tech. Specs. and TMI-2 PDMS Tech.Specs., a Land Use Census shall be conducted and shall identify within a distance of 8 km (5 miles) the location in each of the 16 meteorological sectors of the nearest milk animal, the nearest residence, and the nearest garden* of greater than 50 m 2 (500 ft 2) producing broad leaf vegetation.

8.2.2 Applicability

At all times.8.2.3 Action a. With a Land Use Census identifying a location(s) that yields a calculated dose or dose commitment greater than the values currently being calculated in ODCM Part I Surveillance 3.2.2.3.1, pursuant to ODCM, Part IV, Section 2.0, identify the new location(s) in the next Annual Radioactive Effluent Release Report.b. With a Land Use Census identifying a location(s) that yields a calculated dose or dose commitment (via the same exposure pathway) 20% greater than at a location from which samples are currently being obtained in accordance with Table 8.1, add the new location(s) within 30 days to the Radiological Environmental Monitoring Program given in the ODCM. The sampling location(s), excluding the control station location, having the lowest calculated dose or dose commitment(s), via the same exposure pathway, may be deleted from this monitoring program after October 31 of the year in which this Land Use Census was conducted.

Pursuant to TMI-1 Tech.Spec. 6.14 and TMI-2 PDMS Tech. Spec. 6.12, submit in the next Annual Radioactive Effluent Release Report documentation for a change in the ODCM including a revised figure(s) and table(s) for the ODCM reflecting the new location(s) with information supporting the change in sampling locations.

Broad leaf vegetation sampling of at least three different kinds of vegetation may be performed at the site boundary in each of two different sectors with the highest predicted D/Qs in lieu of the garden census.Requirements for broad leaf sampling in Table 8.1 shall be followed, including analysis of control samples.

CY-TM-1 70-300 Revision 3 Page 172 of 209 8.2.4 Bases This Control is provided to ensure that changes in the use of unrestricted areas are identified and modifications to the monitoring program are made if required by the results of this census. The best information from the door-to-door survey, aerial surveys, or consulting with local agricultural authorities shall be used. This census satisfies the requirements of Section IV.B.3 of Appendix I to 10 CFR 50. Restricting the census to gardens of greater than 500 square feet (50 M 2) provides assurance that significant exposure pathways via leafy vegetables will be identified and monitored since a garden of this size is the minimum required to produce the quantity (26 kg/yr) of leafy vegetables assumed in Regulatory Guide 1.109 for consumption by a child. To determine this minimum garden size, the following assumptions were used: 1) that 20% of the garden was used for growing broad leaf vegetation (i.e., similar to lettuce and cabbage), and 2) a vegetation yield of 2 kg/square meter.8.2.5 Surveillance Requirements The Land Use Census shall be conducted during the growing season at least once per 12 months, using that information that.will provide the best results, such as by a door-to-door survey, aerial survey, or by consulting local agricultural authorities.

The results of the Land Use Census shall be included in the Annual Radiological Environmental Operating Report pursuant to ODCM, Part IV, Section 1.0.

CY-TM-1 70-300 Revision 3 Page 173 of 209 8.3 Interlaboratory Comparison Program 8.3.1 Controls In accordance with the TMI-1 Tech. Specs. and TMI-2 PDMS Tech.Specs., analyses shall be performed on radioactive materials supplied as part of an Interlaboratory Comparison Program which has been approved by the Commission (NRC). Only those samples and analyses which are required by Table 8.1 shall be performed.

8.3.2 Applicability

At all times.8.3.3 Action With analysis not being performed as required above, report the corrective action taken to prevent a recurrence to the Commission in the Annual Radiological Environmental Operating Report.8.3.4 Bases The requirement for participation in an approved Interlaboratory Comparison Program is provided to ensure that independent checks on precision and accuracy of the measurements of radioactive material in environmental sample matrices are performed as part of a quality assurance program for environmental monitoring in order to demonstrate that the results are reasonably valid for the purpose of Section IV, B.2 of Appendix I to 10 CFR 50.8.3.5 Surveillance Requirements A summary of the Interlaboratory Comparison Program results shall be included in the Annual Radiological Environmental Operating Report.

CY-TM-1 70-300 Revision 3 Page 174 of 209 TABLE 8.1 Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb 1. Airborne Radioiodine and Samples from 5 locations Continuous sampler operation Radioiodine Canister: Particulates from Table 8.4. with sample collection weekly, Analyze weekly for 1-131.or more frequently if required Particulate Filter: Three of these samples by dust loading. Analyze for gross beta should be close to the Site radioactivity following filter d Boundary, in different change .Perform gamma sectors, of the highest isotopic analysise on calculated annual average composite (by location)ground level D/Q. sample quarterly.

One of the samples should be from the vicinity of a community having the highest calculated annual average ground level D/Q.And one sample should be from a control location 15 to 30 km distant in a less prevalent wind direction.

CY-TM-170-300 Revision 3 Page 175 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency____ S m Cy oAnlysisb and/or Sample Sample Locationsa CollectionFrequency_

of Analysis _2. Direct Radiationc Samples from 40 locations Sample Quarterly Analyze for gamma dose from Table 8.5 (using either quarterly.

2 dosimeters or at least 1 instrument for continuously measuring and recording dose rate at each location).

Placed as follows: An inner ring of stations, one in each meteorological sector in the general area of the site boundary;An outer ring of stations, one in each meteorological sector in the 6 to 8 km from the site; and the balance of the stations to be placed in special interest areas such as population centers, nearby residences, schools, and in at least one or two areas to serve as control stations.

CY-TM-1 70-300 Revision 3 Page 176 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb 3. Waterborne

a. Surface' Samples from 2 locations Compositeg sample over Perform gamma isotopic from Table 8.6. 1 monthly period. analysis' monthly.Composite for tritium* 1 sample from analysis quarterly.

downstream (indicator) location* 1 sample from upstream (control) location (or location not influenced by the station discharge)

b. Drinking Samples from 2 locations Composite 0 sample over Perform gross beta and from Table 8.6. 1 monthly period, gamma isotopic analysise monthly. Perform Sr-90* 1 sample at the location analysis if gross beta of of the nearest water monthly composite

>10 supply that could be times control. Composite for affected by the station tritium analysis quarterly.

discharge.

  • 1 sample from a control location.c. Sediment from Samples from 2 locations Sample twice per year Perform gamma isotopic Shoreline (1 Control and 1 Indicator) (Spring and Fall) analysise on each sample.from Table 8.7. 1 1 CY-TM-1 70-300 Revision 3 Page 177 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb 4. Ingestion a. Milk b. Fish Samples from 4 locations from Table 8.8.Samples should be from milking animals in three locations within 5 km distance having the highest dose potential.

If there are none, then one sample from milking animals in each of three areas between 5 to 8 km distant where doses are calculated to be greater than 1 mrem per year.One sample from milking animals at a control location 15 to 30 km distant in a less prevalent wind direction.

Samples from 2 locations from Table 8.9.* 1 sample of recreationally important bottom feeders and 1 sample of recreationally important predators in the vicinity of the station discharge.

  • 1 sample of recreationally important bottom feeders and 1 sample of recreationally important predators from an area not influenced by the station discharge.

Sample semimonthly when animals are on pasture;monthly at other times.Sample twice per year (Spring and Fall).Perform gamma isotopic analysise and 1-131 analysis on each sample.Composite for Sr-90 analysis quarterly.

Perform gamma isotopic'and Sr-90 analysis on edible portions.

CY-TM-1 70-300 Revision 3 Page 178 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Number of Samples Exposure Pathway and Sampling and Type and Frequency and/or Sample Sample Locationsa Collection Frequencyb of Analysisb 4. Ingestion (contd)c. Food Products Samples from 2 locations from Table 8.10 (when available)

  • 1 sample of each principle class of food products at a location in the immediate vicinity of the station.(indicator)
  • 1 sample of same species or group from a location not influenced by the station discharge.

Samples of three different kinds of broad leaf vegetation grown nearest each of two different offsite locations of highest predicted annual average ground level D/Q if milking sampling is not performed.

One sample of each of the similar broad leaf vegetation grown 15 to 30 km distant in a less prevalent wind direction if milk sampling is not performed.

Sample at time of harvest.Monthly during growing season Perform gamma isotopice, and 1-131, analysis on edible portions.

Sr-90 analysis on green leafy vegetables or vegetation only.Perform gamma isotopice 1-131 analysis.

CY-TM-170-300 Revision 3 Page 179 of 209 TABLE 8.1 (Cont'd)Sample Collection and Analysis Requirements Table Notation a. Sampling locations are provided in Tables 8.4 through 8.10. They are depicted in Maps 8.1 through 8.3. Deviations are permitted from the required sampling schedule if specimens are unobtainable due to hazardous conditions, seasonal unavailability, malfunction of automatic sampling equipment and other legitimate reasons. All deviations from the sampling schedule shall be explained in the Annual Radiological Environmental Operating Report.b. Frequency notation:

weekly (7 days), semimonthly (15 days), monthly (31 days), and quarterly (92 days). All surveillance requirements shall be performed within the specified time interval with a maximum allowable extension not to exceed 25% of the surveillance interval.

A total maximum combined interval time for any 4 consecutive tests shall not exceed 3.25 times the specified collection or analysis interval.c. One or more instruments, such as a pressurized ion chamber for measuring and recording dose rate continuously, may be used in place of, or in addition to, integrating dosimeters.

For the purpose of this table, a dosimeter is considered to be one phosphor; two or more phosphors in a packet are considered as two or more dosimeters.

Film badges shall not be used as dosimeters for measuring direct radiation.

d. Airborne particulate sample filters shall be analyzed for gross beta radioactivity 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> or more after sampling to allow for radon and thoron daughter decay. If gross beta activity in an air particulate sample(s) is greater than ten times the calendar year mean of control samples, Sr-90 and gamma isotopic analysis shall be performed on the individual sample(s).
e. Gamma isotopic analysis means the identification and quantification of gamma-emitting radionuclides that may be attributable to the effluents from the facility.f. The "upstream sample" shall be taken at a distance beyond significant influence of the discharge.

The "downstream sample" shall be taken in an area beyond but near the mixing zone.g. Composite sample aliquots shall be collected at time intervals that are short (e.g., hourly) relative to the compositing period (e.g., monthly) in order to assure obtaining a representative sample.

CY-TM-1 70-300 Revision 3 Page 180 of 209 TABLE 8.2 Reporting Levels for Radioactivity Concentrations in Environmental Samples Airborne Particulate Water or gas Fish Milk Food Products Analysis (pCi/L) _(pCi/m 3) (pCi/kg,wet) (pCi/L) (pCi/kg, wet)H-3 20,000(a)Mn-54 1000 30,000 FE-59 400 10,000 Co-58 1000 30,000 Co-60 300 10,000 Zn-65 300 20,000 Sr-90 8 0.1 100 8 100 Zr-Nb-95 400 1-131 2 0.9 3 100 Cs-134 30 10 1000 60 1000 Cs-1 37 50 20 2000 70 2000 Ba-La-140 200 300 (a) For drinking Water samples. This is 40 CFR Part 141 value.

CY-TM-1 70-300 Revision 3 Page 181 of 209 TABLE 8.3 Detection Capabilities for Environmental Sample Analysisa Lower Limit of Detection (LLD)b'c Airborne Particulate Fish Food Sediment Water or Gas (pCi/kg, Milk Products (pCi/kg, Analysis (pCi/L) (pCi/m 3) wet) (pCi/L) (pCi/kg,wet) dry)Gross Beta 4 0.01 H-3 2000 Mn-54 15 130 FE-59 30 260 Co-58, 60 15 130 Zn-65 30 260 Zr-95 30 Sr-90 2 0.01 10 2 10 Nb-95 15 1-131 1d 0.07 1 60 Cs-134 15 0.05 130 15 60 150 Cs-137 18 0.06 150 18 80 180 Ba-140 60 60 La-140 15 15 CY-TM-1 70-300 Revision 3 Page 182 of 209 TABLE 8.3 (Cont'd)Detection Capabilities for Environmental Sample Analysisa Table Notation a. This list does not mean that only these nuclides are to be considered.

Other peaks that are identifiable, which may be related to plant operations, together with those of the above nuclides, shall also be analyzed and reported in the Annual Radiological Environmental Operating Report.b. Required detection capabilities for dosimeters used for environmental measurements are given in Regulatory Guide 4.13 (Rev. 1).c. The LLD is defined, for purposes of these controls, as the smallest concentration of radioactive material in a sample that will yield a net count, above system background, that will be detected with 95% probability with only 5% probability of falsely concluding that a blank observation represents a "real" signal.For a particular measurement system (which may include radiochemical separation):

LLD = 4.66 Sb E & V

  • 2.22
  • Y
  • exp (-X At)Where: LLD is the "a priori" lower limit of detection as defined above, as picocuries per unit mass or volume.Sb is the standard deviation of the background counting rate or of the counting rate of a blank sample as appropriate, as counts per minute, E is the counting efficiency, as counts per disintegration, V is the sample size in units of mass or volume, 2.22 is the number of disintegrations per minute per picocurie, Y is the fractional radiochemical yield (when applicable), X is the radioactive decay constant for the particular radionuclide and At for environmental samples is the elapsed time between sample collection, or end of the sample collection period, and time of counting.Typical values of E, V, Y and At should be used in the calculation.

CY-TM-1 70-300 Revision 3 Page 183 of 209 TABLE 8.3 (Cont'd)Detection Capabilities for Environmental Sample Analysisa Table Notation It should be recognized that the LLD is defined as an "a priori" (before the fact) limit representing the capability of a measurement system and not as an "a posteriori" (after the fact) limit for a particular measurement.

Analyses shall be performed in such a manner that the stated LLDs will be achieved under routine conditions.

Occasionally background fluctuations, unavoidable small samples sizes, the presence of interfering nuclides, or other uncontrollable circumstances may render these LLDs unachievable.

In such cases, the contributing factors shall be identified and described in the Annual Radiological Environmental Operating Report.d. LLD for drinking water.

CY-TM-170-300 Revision 3 Page 184 of 209 TABLE 8.4 TMINS REMP Station Locations-Air Particulate and Air Iodine Station Code Distance (miles)E1-2 F1-3 G2-1 M2-1 A3-1 H3-1 Q15-1 0.4 0.6 1.4 1.3 2.7 2.2 13.4 Azimuth (0)97 112 126 256 357 160 309 8.1 8.1 8.2 8.2 8.2 8.2 8.3 Map No.TABLE 8.5 TMINS REMP Station Locations-Direct Radiation Station Code Distance (miles)A1-4 B1-1 B1-2 C1-2 D1-1 E1-2 E1-4 F1-2 G1-3 H1-1 J1-1 J1-3 K1 -4 L1-1 M1-1 N1-3 P1-1 P1-2 0.3 0.6 0.4 0.3 0.2 0.4 0.2 0.2 0.2 0.5 0.8 0.3 0.2 0.1 0.1 0.1 0.4 0.1 Azimuth (0)6 25 23 50 76 97 97 112 130 167 176 189 209 236 250 274 303 292 Map No.8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 CY-TM-1 70-300 Revision 3 Page 185 of 209 TABLE 8.5 (Cont'd)TMINS REMP Station Locations-Direct Radiation Station Code Distance (miles)Q1-2 C2-1 K2-1 M2-1 A3-1 H3-1 R3-1 A5-1 B5-1 C5-1 E5-1 F5-1 G5-1 H5-1 J5-1 K5-1 L5-1 M5-1 N5-1 P5-1 Q5-1 R5-1 D6-1 E7-1 Q9-1 B10-1 G10-1 G15-1 J15-1 Q1 5-1 0.2 0.2 1.5 1.2 1.3 2.7 2.2 2.6 4.4 4.9 4.7 4.7 4.7 4.8 4.1 4.9 4.9 4.1 4.3 5.0 5.0 5.0 4.9 5.2 6.7 8.5 9.2 9.7 14.4 12.6 13.4 Azimuth (0)321 335 44 200 256 357 160 341 3 19 43 82 109 131 158 181 202 228 249 268 284 317 339 66 88 310 21 128 126 183 309 Map No.8.1 8.1 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.2 8.3 8.3 8.3 8.3 8.3 8.3 8.3 8.3 CY-TM-1 70-300 Revision 3 Page 186 of 209 TABLE 8.6 TMINS REMP Station Locations-Surface Water Station Code Distance (miles) Azimuth (0) Map No.J1-2 (SW) 0.5 188 8.1 A3-2 (SW) 2.7 356 8.2 Q9-1 (DW) 8.5 310 8.3 Q9-1 (SW) 8.5 310 8.3 G15-2 (DW) 13.3 129 8.3 G15-3 (DW) 15.7 124 8.3 (SW) = Surface Water (DW) = Drinking Water TABLE 8.7 TMINS REMP Station Locations-Aquatic Sediment Station Code Distance (miles) Azimuth (0) Map No.A1-3 0.5 359 8.1 K1-3 0.2 212 8.1 J2-1 1.4 179 8.2 CY-TM-1 70-300 Revision 3 Page 187 of 209 Station Code E2-2 F4-1 G2-1 P4-1 K15-3 TABLE 8.8 TMINS REMP Station Locations-Milk Distance (miles) Azimuth (0)1.1 96 3.2 104 1.4 126 3.7 295 14.4 205 Map No.8.2 8.2 8.2 8.2 8.3 TABLE 8.9 TMINS REMP Station Locations-Fish Station Code Station Location IND Downstream of Station Discharge BKG Upstream of Station Discharge Station Code E1-2 H11-2 B10-2 TABLE 8.10 TMINS REMP Station Locations-Food Products Distance (miles) Azimuth (0)0.4 97 1.0 151 10.0 31 Map No.8.1 8.1 8.3 CY-TM-170-300 Revision 3 Page 188 of 209 MAP 8.1 THREE MILE ISLAND NUCLEAR STATION LOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM STATIONS WITHIN I MILE OF THE SITE U U.Z U.4 U _ _ _ _ _MAP 8.1 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Within I Mile of the Site CY-TM-170-300 Revision 3 Page 189 of 209 MAP 8.2 THREE MILE ISLAND NUCLEAR STATION LOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM STATIONS WITHIN 5 MILES OF THE SITE MAP 8.2 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Within 5 Miles of the Site CY-TM-170-300 Revision 3 Page 190 of 209 MAP 8.3 THREE MILE ISLAND NUCLEAR STATION LOCATIONS OF RADIOLOGICAL ENVIRONMENTAL MONITORING PROGRAM STATIONS GREATER THAN 5 MILES FROM THE SITE MAP 8.3 Three Mile Island Nuclear Station Locations of Radiological Environmental Monitoring Program Stations Greater Than 5 Miles from the Site CY-TM-1 70-300 Revision 3 Page 191 of 209 9.0 PART Ill REFERENCES

1. EPRI NP-3840, RP 1560-3 Final Report, "Environmental Radiation Doses From Difficult-To-Measure Nuclides," January 1985 2. "Evaluation of the Three Mile Island Nuclear Station Unit 1 to Demonstrate Conformance to the Design Objectives of 10 CFR 50, Appendix I," Nuclear Safety Associates, May 1976 3. TMI-1 Final Safety Analysis Report (FSAR)4. TMI-2 Final Safety Analysis Report (FSAR)5. Meteorological Information and Dose Assessment System (MIDAS)6. NUREG-0017, "Calculation of Releases of Radioactive Materials in Gaseous and Liquid Effluents from PWR," Revision 1, 1985 7. NUREG-0133, "Preparation of Radiological Effluent Technical Specifications for Nuclear Power Plants," October 1978 8. NUREG-01 72, "AgE-Specific Radiation Dose Commitment Factors For A OnE-Year Chronic Intake," November 1977 9. Regulatory Guide 1.21, "Measuring, Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive Materials in Liquid and Gaseous Effluents from Light-Water Cooled Nuclear Power Plants," Revision 1, June 1974 10. Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR 50, Appendix I," Revision 1, October 1977 11. Simplified Environmental Effluent Dosimetry System (SEEDS)12. TMI Recirculation Factor Memos, April 12, 1988 and March 17, 1988 13. TMI-1 Operations Procedure, 1101-2.1, "Radiation Monitor Set Points" 14. Title 10, Code of Federal Regulations, "Energy" 15. TMI-1 Technical Specifications, attached to Facility Operating License No. DPR-50 16. Regulatory Guide 1.111, "Methods for Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors," Revision 1, July 1977 17. TMI-2 PDMS Technical Specifications, attached to Facility License No. DPR-73 CY-TM-1 70-300 Revision 3 Page 192 of 209 18. Radiological Assessment Branch Technical Position on Environmental Monitoring, Revision 1, November 1979 19. Title 40, Code of Federal Regulations, "Protection of Environment" 20. Regulatory Guide 4.13, "Performance, Testing, and Procedural Specifications for Thermoluminescence Dosimetry:

Environmental Applications," Revision 1, July 1977 21. Post-Defueling Monitored Storage Safety Analysis Report (PDMS SAR)

CY-TM-170-300 Revision 3 Page 193 of 209 PART IV REPORTING REQUIREMENTS CY-TM-1 70-300 Revision 3 Page 194 of 209 PART IV Reporting Requirements 1.0 TMI ANNUAL RADIOLOGICAL ENVIRONMENTAL OPERATING REPORT 1.1 Routine Radiological Environmental Operating Reports covering the operation of the unit during the previous calendar year shall be submitted to the Commission prior to May 1 of each year.1.2 The Annual Radiological Environmental Operating Reports shall include summaries, interpretations, and an analysis of trends of the results of the radiological environmental monitoring activities for the report period, including a comparison with prE-operational studies, with operational controls as appropriate, and with previous environmental monitoring reports, and an assessment of the observed impacts of the plant operation on the environment.

The reports shall also include the results of Land Use Censuses required by Part III, Section 8.2.1.3 The Annual Radiological Environmental Operating Reports shall include the summarized tabulated results of analysis of all radiological environmental samples and environmental radiation measurements required by Part III Table 8.1 taken during the period pursuant to the locations specified in the tables and figures in this ODCM, as well as summarized and tabulated results of these analyses and measurements in a format similar to the table in the Radiological Assessment Branch Technical Position, Revision 1, November 1979. In the event that some individual results are not available for inclusion with the report, the report shall be submitted explaining the reasons for the missing results. The missing data shall be submitted as soon as possible in a supplementary report.1.4 The reports shall also include the following:

A summary description of the radiological environments monitoring program; a map(s) of all sampling locations keyed to a table giving distances and directions from a point that is midway between the Reactor Buildings of TMI-1 and TMI-2; the results of licensee participation in the Interlaboratory Comparison Program, required by Part Ill, Section 8.3; discussion of all deviations from the sampling schedule of Part III, Table 8.1; discussion of all the required analyses in which the LLD required by Part III, Table 8.3 was not achievable.

A single submittal may be made for the station.

CY-TM-1 70-300 Revision 3 Page 195 of 209 2.0 TMI ANNUAL RADIOACTIVE EFFLUENT RELEASE REPORT NOTE: A single submittal may be made for the station. The submittal should combine those sections that are common to both units at the station however, for units with separate radwaste systems, the submittal shall specify the release of radioactive material from each unit.2.1 Routine Radioactive Effluent Release Reports covering the operations of the unit during the previous 12 months of operation shall be submitted prior to May 1 for TMI-1 and TMI-2.2.2 The following information shall be included in both Radioactive Effluent Release Reports to be submitted each year: The Radioactive Effluent Release Reports shall include a summary of the quantities of radioactive liquid and gaseous effluents and solid waste released from the unit as outlined in Reg. Guide 1.21, Rev. 1, with data summarized on a quarterly basis following the format of Appendix B thereof.2.3 The Radioactive Effluent Release Reports shall include the following information for each type of solid waste shipped offsite during the report period: a. Container volume b. Total curie quantity (specify whether determined by measurement or estimate)c. Principal radionuclides (specify whether determined by measurement or estimate)d. Type of waste (e.g., spent resin, compacted dry waste, evaporator bottoms)e. Type of shipment (e.g., Isa, type a, type b) and f. Solidification agent (e.g., cement)2.4 The Radioactive Effluent Release Reports shall include a summary of unplanned releases from the site to unrestricted areas of radioactive materials in gaseous and liquid effluents made during the reporting period.2.5 The Radioactive Effluent Release Reports shall include any changes made during the reporting period to the PROCESS CONTROL PROGRAM (PCP)documents and to the OFFSITE DOSE CALCULATION MANUAL (ODCM), as well as a listing of new locations for dose calculations and/or environmental monitoring identified by the land use census pursuant to Part III Section 8.2.

CY-TM-1 70-300 Revision 3 Page 196 of 209 2.6 The Radioactive Effluent Release Reports shall include the instrumentation not returned to OPERABLE status within 30 days per ODCM Part I Controls 2.1.1 b and 2.1.2b, and ODCM Part II Control 2.1.2b.2.7 The Radioactive Effluent Release Report to be submitted shall include an annual summary of hourly meteorological data collected over the previous year. This annual summary may be either in the form of an hour-by-hour listing of wind speed, wind direction, atmosphere stability, and precipitation (if measured) on magnetic tape, or in the form of joint frequency distribution of wind speed, wind direction, and atmospheric stability.

2.8 The Radioactive Effluent Release Report shall include an assessment of the radiation doses to MEMBERS OF THE PUBLIC due to the radioactive liquid and gaseous effluents released from the unit or station during the previous calendar year. The meteorological conditions concurrent with the time of release of radioactive materials in gaseous effluents (as determined by sampling frequency and measurement) shall be used for determining the gaseous pathway doses.The assessment of radiation doses shall be performed in accordance with this ODCM.2.9 The Radioactive Effluent Release Report shall include an assessment of the radiation doses from radioactive liquid and gaseous effluents to MEMBERS OF THE PUBLIC due to their activities inside the SITE BOUNDARY during the report period, to verify compliance with the limits of 1OCFR20.1301 (a)(1). All assumptions used in making these assessments (i.e., specific activity, exposure time and location) shall be included in these reports.2.10 The Radioactive Effluent Release Report shall also include an assessment of radiation doses to the likely most exposed real individual from reactor releases, and other nearby uranium fuel cycle sources, including doses from primary effluent pathways and direct radiation for the previous 12 consecutive months, to show conformance with 40 CFR 190 "Environmental Radiation Protection Standards for Nuclear Power Operation." Acceptable methods for calculating the dose contributions from liquid and gaseous effluents are given in Regulatory Guide 1.109, Rev. 1.

CY-TM-1 70-300 Revision 3 Page 197 of 209 3.0 PART IV REFERENCES 3.1 Radiological Assessment Branch Technical Position, Revision 1, November 1979 3.2 Regulatory Guide 1.21, "Measuring, Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive Materials in Liquid and Gaseous Effluents from Light-Water-Cooled Nuclear Power Plants," Revision 1, June 1974 3.3 TMI-1 Technical Specifications, attached to Facility Operating License No.DPR-50 3.4 Title 40, Code of Federal Regulations, "Protection of Environment" 3.5 Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977 3.6 Title 10, Code of Federal Regulations, "Energy" 3.7 Regulatory Guide 1.111, "Methods of Estimating Atmospheric Transport and Dispersion of Gaseous Effluents in Routine Releases from Light-Water-Cooled Reactors," Revision 1, July 1977 3.8 Regulatory Guide 1.112, "Calculation of Releases of Radioactive Materials in Gaseous and Liquid Effluents from Light-Water-Cooled Power Reactors," Revision O-R, April 1976 3.9 Regulatory Guide 1.113, "Estimating Aquatic Dispersion of Effluents from Accidental and Routine Reactor Releases for the Purpose of Implementing Appendix I," Revision 1, April 1977 CY-TM-1 70-300 Revision 3 Page 198 of 209 APPENDIX A Page 1 of 1 P, -Pathway Dose Rate Parameter P, (inhalation)

= k' (BR) DFAI (Eq A-I)Where: Pi = the pathway dose rate parameter for radionuclide,-

i, (other than noble gases) for the inhalation pathway, in mrem/yr per microcurie/m 3.The dose factors are based on the critical individual organ for the child age group.k' = conversion factor, 1 E6 pCi/microcurie BR = 3700 m 3/yr, breathing rate for child (Reg. Guide 1.109, Rev. 1, Table E-5)DFA= = the maximum organ inhalation dose factor for the infant age group for the ith adionuclide (mRem/pCi).

Values are taken from Table E-10, Reg. Guide 1.109 (Rev. 1), or NUREG-01 72.Resolution of the units yields: (ODCM Part III Table 4.6)Pi (inhalation)

= 3.7E9 DFAI (mrem/yr per PCi/m 3) (Eq A-2)NOTE: The latest NRC Guidance has deleted the requirement to determine Pi (ground plane) and Pi (food). In addition, the critical age group has been changed from infant to child.

CY-TM-1 70-300 Revision 3 Page 199 of 209 APPENDIX B Page 1 of I R, -Inhalation Pathway Dose Factor R1 = k' (BR) (DFAi,a,o) (mrem/yr per microcurie/m

3) (Eq B-I)Where: k' = conversion factor, 1 E6 pCi/microcurie BR = breathing rate, 1400, 3700, 8000, 8000 m 3/yr for infant, child, teenager, and adult age groups, respectively. (Reg. Guide 1.109, Rev. 1, Table E-5)DFAi,a,o = the inhalation dose factor for organ, o, of the receptor of a given age group, a, and for the ith radionuclide, in mrem/pCi.

The total body is considered as an organ in the selection of DFAi,ao. Values are taken from Tables E-7 through E-10, Reg. Guide 1.109 (Rev. 1), or NUREG 0172.Resolutions of the units yields: R, = (1.4E9) (DFAi,a,o) infant (ODCM Part III Table 5.2.1)R1 = (3.7E9) (DFAi,a,o) child (ODCM Part III Table 5.2.2)Rj = (8.0E9) (DFAi,ao) teen and adult (ODCM Part III Tables 5.2.3 and 5.2.4)

CY-TM-1 70-300 Revision 3 Page 200 of 209 APPENDIX C Page 1 of 1 R, -Ground Plane Pathway Dose Factor R, = k' k" (SF) (DFGj) [(1-e "it)/X 1] (Eq C-1)Where: k' = conversion factor, 1 E6 pCi/microcurie k" = conversion factor, 8760 hr/yr= decay constant for the ith radionuclide, sec t = the exposure time (this calculation assumes that decay is the only operating removal mechanism) 4.73 x 108 sec. (15 yrs), Reg. Guide 1.109 (Rev. 1), Appendix C DFG 1 = the ground plane dose conversion factor for the ith radionuclide (mrem/hr per pCi/m 2). Values are taken from Table E-6, Reg. Guide 1.109 (Rev. 1), or NUREG 0172. These values apply to all age groups.SF = 0.7, shielding factor, from Table E-15 Reg. Guide 1.109 (Rev'. 1)Reference ODCM Part III Table 5.3.1 CY-TM-170-300 Revision 3 Page 201 of 209 APPENDIX D Page 1 of 2 R, -Grass Cow-Milk Pathway Dose Factor Rim k' [(QF X UAP) / (Xi + Xw)] x (Fo) x (r) x (DFLi,a,o) x[((fp x fs)/Yp) + ((I-fp x fs) e -ith)IYs]

E-Xitf (Eq D-1)Where: k' = conversion factor, 1 E6 picocurie/microcurie (pCi/lgci)

QF = cow consumption rate, 50 kg/day, (Reg. Guide 1.109, Rev. 1)goat consumption rate, 6 kg/day, (Reg. Guide 1.109, Rev. 1, Table E-2)UAP = Receptor's milk consumption rate; 330, 330, 400, 310 liters/yr for infant, child, teenager, and adult age groups, respectively (Reg. Guide 1.109, Rev. 1)Yp = agricultural productivity by unit area of pasture feed grass, 0.7 kg/M 2 (NUREG-0133)

Ys = agricultural productivity by unit area of stored feed, 2.0 kg/M 2 (NUREG-0133)

Fm = stable element transfer coefficient (Table E-1, Reg. Guide 1.109, Rev. 1)r = fraction of deposited activity retained in cow's feed grass, 0.2 for particulates, 1.0 for radioiodine (Table E-15, Reg. Guide 1.109, Rev. 1)DFLi,a,o = the ingestion dose factor for organ, o, and the ith radionuclide for each respective age group, a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.ki = decay constant for the ith radionuclide, sec-1;L, = decay constant for weathering, 5.73 x 10-7 sec-1 (NUREG-0133);

based on a 14 day half life tf = 1.73 x 105 sec, the transport time from pasture to cow to milk to receptor (Table E-15, Reg. Guide 1.109, Rev. 1), or 2 days th = 7.78 x 106 sec, the transport time from pasture to harvest to cow to milk to receptor (Table E-15, Reg. Guide 1.109, Rev. 1), or 90 days fp = 1.0, the fraction of the year that the cow is on pasture fs = 1.0, the fraction of the cow feed that is pasture grass while the cow is on pasture CY-TM-1 70-300 Revision 3 Page 202 of 209 APPENDIX D Page 2 of 2 The concentration of tritium in milk is based on the airborne concentration rather than the deposition.

Therefore, Ri is based on (X/Q): Rct,a,o = k'k"' Fm QF UApDFLt,a,o

(.75 [.5/HI) (Eq D-2)Where: k"' = 1E3 grams/kg H = 8 grams/m 3 , absolute humidity of the atmosphere

.75 = fraction of the total feed grass mass that is water.5 = ratio of the specific activity of the feed grass water to the atmospheric water (NUREG-0133)

DFLt,a,o = the ingestion dose factor for tritium and organ, o, for each respective age group, a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.All other parameters and values are as given above.NOTE: Goat-milk pathway factor, Ri, will be computed using the cow-milk pathway factor equation.

Fm factor for goat-milk will be from Table E-2 Reg. Guide 1.109, Rev. 1.

Reference:

ODCM Part III Tables 5.4.1 to 5.4.4 CY-TM-1 70-300 Revision 3 Page 203 of 209 APPENDIX E Page 1 of 2 R, -Cow-Meat Pathway Dose Factor Ri= k' [(QF X UAP) I (Xi+ X (Ff) x (r) x (DFLi,a,o) x[((fp x fs)/Yp) + ((I-fpfs) e "'ith)/Ys]

x E-xitf (Eq E-1)Where: k' = conversion factor, 1 E6 picocurie/microcurie (pCi/gci)QF = cow consumption rate, 50 kg/day, (Reg. Guide 1.109, Rev. 1)UAP = Receptor's meat consumption rate; 0, 41, 65, 110 kg/yr for infant, child, teenager, and adult age groups, respectively (Reg. Guide 1.109, Rev. 1)Ff = the stable element transfer coefficients, days/kg (Table E-1, Reg. Guide 1.109, Rev. 1)r = fraction of deposited activity retained in cow's feed grass, 0.2 for particulates, 1.0 for radioiodine (Table E-15, Reg. Guide 1.109, Rev. 1)DFLi,a,o = the ingestion dose factor for organ, o, and the ith radionuclide for each respective age group, a (Tables E-11 to E-14, Reg. Guide 1.109, Rev. 1), or NUREG 0172.XI = decay constant for the radionuclide i, sec1 X, = decay constant for weathering, 5.73 x 10- sec1 (NUREG-0133), based on a 14 day half life tf = 1.73 x 106 sec, the transport time from pasture to receptor (NUREG-01 33)th = 7.78 X 106 sec, the transport time from crop to receptor (NUREG-01 33)Yp = agricultural productivity by unit area of pasture feed grass, 0.7 kg/M 2 (NUREG-0133)

Ys = agricultural productivity by unit area of stored feed, 2.0 kg/M 2 (NUREG-0133) fp = 1.0, the fraction of the year that the cow is on pasture fs = 1.0, the fraction of the cow feed that is pasture grass while the cow is on pasture CY-TM-1 70-300 Revision 3 Page 204 of 209 APPENDIX E PAGE 2 OF 2 The concentration of tritium in meat is based on the airborne concentration rather than the deposition.

Therefore, Ri is based on (X/Q): Rt,a,o = k'k'" Ff QF UAP (DFLt,a,o) x 0.75 x (0.5/H]) (Eq E-2)Where: All terms are as defined above and in Appendix D.

Reference:

ODCM Part III, Tables 5.6.1 to 5.6.4 CY-TM-170-300 Revision 3 Page 205 of 209 APPENDIX F PAGE 1 OF I R, -Vegetation Pathway Dose Factor R, k' x [r/ (Y, (k, + kw))] x (DFLi,a,o)

X [(ULA) fL E'XitL + USA fg E-'ith] (Eq F-1)Where: k' = 1 E6 picocurie/microcurie (pCi/jLci)

ULA = the consumption rate of fresh leafy vegetation, 0, 26, 42, 64 kg/yr for infant, child, teenager, or adult age groups, respectively (Reg. Guide 1.109, Rev. 1)UsA = the consumption rate of stored vegetation, 0, 520, 630, 520 kg/yr for infant, child, teenager, or adult age groups respectively (Reg. Guide 1.109, Rev. 1)fL = the fraction of the annual intake of fresh leafy vegetation grown locally, = 1.0 (NUREG-0133) fg = the fraction of the stored vegetation grown locally = 0.76 (NUREG-0133) tL = the average time between harvest of leafy vegetation and its consumption, 8.6 x 104 seconds [Table E-15, Reg. Guide 1.109, Rev. 1 (24 hrs)]th = the average time between harvest of stored leafy vegetation and its consumption, 5.18 x 10 seconds, [Table E-15, Reg. Guide 1.109, Rev. 1 (60 days)]yv = the vegetation area density, 2.0 kg/mi 2 (Table E-15, Reg. Guide 1.109, Rev. 1)All other parameters are as previously defined.The concentration of tritium in vegetation is based on the airborne concentration rather than the deposition.

Therefore, Ri is based on (X/Q)Rt,a,o = k'k"' [ULA fL + USA fg] (DFLt,a,o)

(.75 [.5/1H]) (Eq F-2)Where: All terms are as defined above and in Appendix D.

Reference:

ODCM Part III, Tables 5.7.1 to 5.7.4 CY-TM-1 70-300 Revision 3 Page 206 of 209 APPENDIX A-F REFERENCES (Page 1 of 4)Parameters Used in Dose Factor Calculations Origin of Value Table in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 Specific For Pi ***DFA, Each radionuclide E-9 Note 1 BR 3700 m 3/yr (child) E-5***For Ri (Vegetation)***

r Each element type E-1 Yv 2.0 kg/m 2 E-15 kw 5.73 E-7 sec' 5.3.1.3 DFL 1 Each age group and radionuclide E-1 1 thru E-14 Note 1 UaL Each age group E-5 fL 1.0 5.3.1.5 tL 8.6 E + 4 seconds E-15 Uas Each age group E-5 fg 0.76 5.3.1.5 th 5.18 E + 6 seconds E-15 H 8.0 grams/kg 5.2.1.3***For Ri (Inhalation)***

BR Each age group E-5 DFA, Each age group and nuclide E-7 thru E-10 Note 1 CY-TM-1 70-300 Revision 3 Page 207 of 209 APPENDIX A-F REFERENCES (Page 2 of 4)Parameters Used in Dose Factor Calculations Origin of Value Table in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 Specific For Ri (Ground Plane)SF 0.7 E-1 5 DFGj Each radionuclide E-6 t 4.73 E + 8 sec 5.3.1.2 For R 1 (Grass/Animal/Meat)

QF(COW) 50 kg/day E-3 QF (Goat) 6 kg/day E-3 Ref. Only Uap Each age group E-5 xw 5.73 E-7 sec 1 5.3.1.3 Ff (Both) Each element E-1 r Each element type E-15 DFLI Each age group and nuclide E-1 1 thru E-14 Note 1 fp 1.0 5.3.1.3 Note 2 f 1.0 5.3.1.3 Note 2 Yp 0.7 kg/m 3 E-15 th 7.78 E + 6 sec E-15 Ys 2.0 kg/m 2 E-15 tf 1.73 E + 6 sec E-15 H 8.0 grams/kg 5.2.1.3 CY-TM-1 70-300 Revision 3 Page 208 of 209 APPENDIX A-F REFERENCES (Page 3 of 4)Parameters Used in Dose Factor Calculations Origin of Value Table in Section of SitE-Parameter Value R.G. 1.109 NUREG-0133 Specific For R, (Grass/Cow/Milk)

      • Q, 50 kg/day E-3 Uap Each age group E-5 Xw 5.73 E-7 sec 1 5.3.1.3 Fm Each element E-1 r Each element type E-1 5 DFL 1 Each age group and nuclide E-1 1 thru E-14 Note 1 Yp 0.7 kg/mi 2 E-15 th 7.78 E + 6 sec E-15 Ys 2.0 kg/M 2 E-15 tf 1.73 E + 5 sec E-15 fp 1.0 5.3.1.3 s 1.0 5.3.1.3 H 8.0 grams/kg 5.2.1.3 CY-TM-1 70-300 Revision 3 Page 209 of 209 APPENDIX A-F REFERENCES (Page 4 of 4)NOTES 1. Inhalation and ingestion dose factors were taken from the indicated source. For each age group, for each nuclide, the organ dose factor used was the highest dose factor for that nuclide and age group in the referenced table.2. Typically, beef cattle are raised all year on pasture. Annual land surveys have indicated that the small number of goats raised within 5 miles, typically are used for grass control and not food or milk. Nevertheless, the goats can be treated as full meat sources where present, despite the fact that their numbers cannot sustain the meat consumption rates of Table E-5, NUREG-01 33.REFERENCES
1. Regulatory Guide 1.109, "Calculation of Annual Doses to Man from Routine Releases of Reactor Effluents for the Purpose of Evaluating Compliance with 10 CFR Part 50, Appendix I," Revision 1, October 1977.2. TMI-1 Technical Specifications, attached to Facility Operating License No. DPR-50.3. NUREG-01 33, "Preparation of Radiological Effluent Technical Specifications for Nuclear Power Plants," October 1978.

50.59 APPLICABILITY REVIEW FORM Activity/Document Number: i -Revision Number: Title: .QC$ _ VZ(:_V ~/ ~Io LS-AA-104-1002 Revision 4 Page I of I I Address the questions below for all aspects of the Activity.

If the answer is yes for any portion of the Activity, apply the identified process(es) to that portion of the Activity.

Note that it is not unusual to have more than one process apply to a given Activity.

See Section 4 of the Resource Manual (RM) for additional guidance.1. Does the proposed Activity involve a change: I. Technical Specifications or Facility Operating License (1OCFR50.90)?

I NO [I YES See Section 4.2.1.1 of the RM 2. Conditions of License Quality Assurance program (1 OCFR50.54(a))?

XNO C1 YES Security Plan (I OCFR50.54(p))?

NO E] YES See Section 4.2.1.2 of the RM Emergency Plan (IOCFR50.54(q))?

I NO [] YES 3. Codes and Standards IST Program Plan (IOCFR50.55a(O)?

[NO Dl YES See Section 4.2.1.3 of the RM ISI Program Plan (IOCFR50.55a(g))?

'NO El YES 4. ECCS Acceptance Criteria (IOCFR50.46)?

PqNO El YES See Section 4.2.1.4 of the RM 5. Specific Exemptions (IOCFR50.12)?

25NO E] YES See Section 4.2.1.5 of the RM 6. Radiation Protection Program (IOCFR20)?

KNO [I YES See Section 4.2.1.6 of the RM 7. Fire Protection Program (applicable UFSAR or operating license EgNO 0l YES See Section 4.2.1.7 of the RM condition)?

8. Programs controlled by the Operating License or the Technical ANO [: YES See Section 4.2.1.7 of the RM Specifications (such as the ODCM).9. Environmental Protection Program [NO E] YES See Section 4.2.1.7 of the RM 10. Other programs controlled by other regulations.

toa.p.(, I ,l0 El NO K"YES See Section 4.2.1 of the RM II. Does the proposed Activity involve maintenance which restores SSCs to their original condition or involve a temporary alteration supporting D(NO maintenance that will be in effect during at-power operations for 90 days or less?Ill. Does the proposed Activity involve a change to the: I1. UFSAR (including documents incorporated by reference) that is limited to reformatting, simplification, removing excessive detail, or minor XNO Cl YES See Section 4.2.3 of the RM editorial changes as discussed in NEI 96-07 or NEI 98-03?2. Managerial or administrative procedures governing the conduct of [E NO rMYES See Section 4.2.4 of the RM facility operations (subject to the control of IOCFR50, Appendix B)3. Procedures for performing maintenance activities (subject to IOCFR50, [I"NO C1 YES See Section 4.2.4 of the RM Appendix B)?4. Regulatory commitment not covered by another regulation based change KNO 0l YES See Section 4.2.3/4.2.4 of the RM process (see NEI 99-04)?IV. Does the proposed Activity involve a change to the Independent Spent Fuel (NO El YES See Section 4.2.6 of the RM Storage Installation (ISFSI) (subject to control by 10 CFR 72.48)Check one of the following:

  • If all asoects of the Activity are controlled by one or more of the above processes, then a 50.59 Screening is not required and the Activity may be implemented in accordance with its governing procedure.

El If any portion of the Activity is not controlled by one or more of the above processes, then process a 50.59 Screening for the portion not covered by any of the above processes.

The remaining portion of the activity should be implemented in accordance with its governing procedure.

0.59 S _ Sign: I Date: (Circle One) (Print name) (Signature)

C 50.59 REVIEW COVERSHEET FORM LS-AA-104-1001 Revision 3 Page 1 of 1 Station/Unit(s):

TMI -1 Activity/Document Number: RW-AA-100 Revision Number: 8 Title: Process Control Program for Radioactive Wastes NOTE: For 50.59 Evaluations, information on this form will provide the basis for preparing the biennial summary report submitted to the NRC in accordance with the requirements of 10 CFR 50.59(d)(2).

Description of Activity: (Provide a brief, concise description of what the proposed activity involves.)

Issue rev 8 of corporate procedure RW-AA- 100, Process Control Program for Radioactive Wastes which describes the administrative program requirements for the Process Control Program (PRP).Rev 8 changes include:* (step 4.1.8) Allow an Exelon Nuclear plant to store radioactive waste from another Exelon Nuclear plant provided formal NRC approval is granted for the transfer of waste.0 (step 4.2.8) modify statement to include " in the pool or loading the processed activated hardware into Dry Case storage system."* (step 4.4.4) Add statement that Shipment sent off-site storage shall meet the storage site's waste acceptance criteria.* Minor editorial changes and grammatical error corrections to improve readability of the document.Reason for Activity: (Discuss why the proposed activity is being performed.)

RW-AA- 100 rev 8 steps 4.1.8 and 4.4.4 are added to address transfer and storage of radioactive waste from one Exelon Nuclear plant to another Exelon Nuclear plant provided formal NRC approval is granted. Step 4.2.8 is amended to further clarify the storage of activated hardware.Effect of Activity: (Discuss how the activity impacts plant operations, design bases, or safety analyses described in the UFSAR.)The activity is a change to an administrative procedure and has no impact on plant operations, design basis, or safety analysis described in the UFSAR.Summary of Conclusion for the Activity's 50.59 Review: (Provide justification for the conclusion, including sufficient detail to recognize and understand the essential arguments leading to the conclusion.

Provide more than a simple statement that a 50.59 Screening, 50.59 Evaluation, or a License Amendment Request; as applicable, is not required.).

.... .... ......The Process Control Program is a tech spec required program to ensure processed Radioactive Wastes meets applicable criteria for disposal.

RW-AA-100 is an admihistrative procedure governing the conduct of facility operation and is not subject to IOCFR50.59 review in accordance with LS-AA-104-1000 section 4.2.4, Exelon 50.59 Resource Manual.Attachments:

Attach all 50.59 Review forms completed, as appropriate.

Forms Attached: (Check all that apply.)0 Applicability Review E0 50.59 Screening 50.59 Screening No. Rev.EJ 50.59 Evaluation 50.59 Evaluation No. Rev.

Fleet Standard Document -Corporate Approval Form AD-AA-101-F-09 Page 2 of 2 Revision 0 1. Step 4.1.8 suggested wording should read: "An Exelon Nuclear plant may store waste at another Exelon Nuclear plant, provided formal NRC approval has been received for the transfer of waste." 2. Add a step under section 4.4 "Shipment sent for off site storage shall meet the storage site's waste acceptance criteria 3. Add step 4.1.8 "It also possible to store waste from one nuclear plant at another nuclear plant, if formal NRC approval has been received." 4. Modify step 4.2.8 by adding the following words at the end of sentence "in the pool or loading the processed activated hardware into Dry Case storage system.

Fleet Standard Document -Corporate Approval Form Page 1 of 2 AD-AA-101-F-09 Revision 0 See AD-AA- 101 for the procedural requirements associated with this Form.Desktop Instruction available on Intranet or through AD functional area.Document Number: RW-AA-100 Revision:

8 Title: Process Control Program for Radioactive Wastes Superseded Fleet Standard Documents:

NIA 0 or List: Batch -Are multiple document creations/revisions/cancelations being issued to add/revise/cancel them for similar reouirements?

No M or Yes fl If Yes, then identify the hiohest level Document and Issue Type below.Check only one Document Tvoe: Check only one Issue Type: Incorporated Fleet Items: Level 1 -Continuous Use Procedure El New El Level 2 -Reference Use Procedure 0 Revision 0 Level 3 -Information Use Procedure 0 Editorial Revision 0 T&RM 0 Cancel Document [Form E] Cancel Revision __Revision Summary: See attached Summary of Changes.(Attach additional descdption iR rewuired)CONFIRM that no commitments (i.e., those steps annotated with CM-X) have been changed or deleted unless evaluated via completion of LS-AA-1 10 commitment change/deletion form and INITIAL [Preparer]:

RMC Preparer Robert Class 03/07/12 canterwafs0372829 Print Date Location and EUt Site Applicability and Contacts -Check box and provide name: BRW 0 Michael Gorap DRE 0 Sandy Uvecchl OYS 0 Gonzalo Lamena TMI 0 Tamara Hanlon BYR 0 Norma Gordon LAS [ Lynn Kofold-Durden PEA 0 George Tharpe ZIN 0 CPS 0 Anthony KllbUm LIM 0 Unda Knapp QDC Debra Cline Other 0 Affected Functional Area (FA) -Check box & provide Corporate contact name if FA is affected by this revision: AD [I ER [] NO C_ RW [I AR [I_ HRO [ OP 0_ SA [I B1O [1 HUO _ OUO _ _SM []Cc [] IT _ _3. PC 0_ SY 0_CY []_ LR [-_ PI _ _ TO []El 0 LS 0_ PL [I WC 0_ENO MAO [ RM 0 -__EP []_ NF I" RP [] -__I___'Validation

-Is substantiating this document's usability via mockup, simulated performance, field walkdown, or bench top review required?

No 0 or Yes [] ff Yes, then attach validation documentation.

If Yes, then print name & sign for completed validation:

4-NOS Review -Excluding NDE, ISI, Peer Inspection or Independent Verification, is this document used to perform independent inspection for acceptance (including field installation inspections, fabrication inspections, receipt inspections, new fuel inspection, etc.), or for certification of Inspection personnel?

No 0 or Yes C0 If Yes, then NOS Reviewer to print name & sign for acceptance:

Common Training -Is common training material being provided? (Document in the change management how the common training material will be developed and pmvided to the sites or attach.) No 0 or Yes 01 Change Management provided in: HU-AA-)4'1 CPaWge Checklist Attached [I or: As directed by SFAM Z r CFAM Approval Miguel Azar/ /j .03/07/12 Cantera/3240 EPd -V Date Location and Ext SRRS Number 1B.100 Document Site Approval Form Page 2 of 2 AD-AA-101-F-O1 Revision 4 Continuation B -Is this a T&RM, or Form? NodS or Yes [] If yes, then skip the following section and go Continuation C.PORC R quired: If yes, then enter PORC Numr r (a er P Approved):

Plant Manager Print and Si (whn regu)e by procedure)

_ _,, b _,ate Continuation C -Is this an Editorial Revision;,No]%,or es If yes, then skip the following section and go to Continuation D.Applicable Site. Contact/Site Change Agents (SME): -1 C *-Responsible for Change Management information in---his form or E] HU-AA-1 101 Checklist (attached)

-Responsible to shepherd the document through site review, approval/authorization, and implementation.

Affected Functional Area(s) or Individuals:-j) Pit ,, U Signature Date Af e FA Print Signature Date Affected FA Prnt Signature Date Affected FA Attach additional if recfd Resources needed to Implement Change: "At rOnly list, if other than Level of Effort.)For ongoing impacts, estimate number of Full Time Equivalents (FTE). If additional resources are needed go to HU-AA-1101.Communication Plan: (e.g., e-mail, Site Paper, Supervisor Briefing, Voice Mail, etc.)Training Required I Qualifications affected: El Yes If yes, list: (e.g., Supervisory Briefing, Tailgate Briefing, Required Reading, Formal Training, recertification etc.)Update to information infrastructure (e.g. PassPort, PIMS, EDMS w9flows, etc.) required to support implementation (including updated forms loaded into PassPort):

AV Controlled Document distribution (ref. RM-AA-1 02) or Records Retention Schedule (ref. RM-AA-1 01-1004)impacted:

$No 0l Yes If yes, describe change and list Records Manager contacted:

I Continuation D -If all procedurally required activities associated with this document revision have been completed and the document is ready for implementatio4, then SFAM to print name, sign & date for authorization to implement.

Provide implementation date or, if the Implementation Date is blank or N/A then implementation will be upon the issuance by Records Management per RM requirements.

Authorization below indicates the SFAM or a designee of the SFAM has verified the document does not alter or negatively impact compliance with regulatory requirements or L#tOGln ý^mnlfmmnfa I Interim Chg # 01 Authorization:

A1/... /4L..L'Z_____

i-PPrintaate Imi, Date Exp. Date SRRS Number 1 B.160 Document Site Approval Form Page 1 of 2 AD-AA-1 01 -F-01 Revision 4 See AD-AA-101 for the procedural requirements associated with this Form.Desktop Instruction available on Intranet or through AD functional area. ý Facility: DocumetNumber:

P,),.) G (00 Revision:

W Title: a-F-S, C a cr V .o XcA' A Superseded Documents:

N/AKor List: W E] Check this box if superseding a document containing commitments, 'notify the Commitment Trabking Coordinator per LS-AA-1 10 so the CTD can be updated as appropriate.

Environmental Review Applicability

-Is an Environmental Review ap5plicable per EN-AA-1 03? Noj or Yes E]If Yes, then attach Environmental Review documentation required per EN-AA-103. , I Is this a Fleet Standard Document being pirocessed with form AD-AA-1O1-F-09?

No E] or Yes K If yes, then attach the completed form AD-AA- 10.-F-09, skip the following section, and go to Continuation A. 41 Qth -Are multiple document creations/revisionslcancelations being issued to add/revise/cancel them for similar redbizements?

No M- or Yes -- If Yes. then identify the hiahest level Document and Issue Tvne below Check oni e Document Type: Check only one Issue Type: Incorporated Site ItemsML, AR, Level 1 -Con i us Use Procedure El .New E] PCR, etc): ,ýn~ usRevision E Level 2 -Referenc se Procedure E]Cancel Document Level 3 -Information Us rocedure El Cancel Revision E]RM Non-Permanent El Fo Editorial Revision Revision Summary: ý 7 (Attach additional description if CONFIRM that no commitments (i.e., those steps CM-X) have been changed or deleted unless evaluated via completion of LS-AA-1 10 commitmenJ, eiange~deaietion form and INITIAL [Preparer]:

PreprerPrintJ Date Extension Validation

-Is substantiating this cument's usability via mockup, simulatedl*.

ormance, field walkdown, or bench top review required?

NeU or Yes n ] m f Yes, then attach validation documeen.If Yes, then print narneWgn for completed validation:

NOS Review -_.ý.-'1ding NDE, ISI, Peer Inspection or Independent Verification, is this docurne'ht, sed to perform for acceptance (including field installation inspections, fabrication inspecJ~ts, new fuel inspection, etc.), or for certification of Inspection personnel?No E] or Yes Elthen NOS Reviewer to print name & sign for acceptance: Continuation A -Is this a T&RM, Form, or Editorial Revision?

No PS or Yes L] If yes, then skip the following section and go Continuation B.Impact on Operating and Design Margins -N/A~jor explain: (Attach additional description if required)No [] Yes I0CFR50.59 Applicable?

Tracking Number (/A,.KNo [] Yes 10CFR72.48 Applicable?

9No El Yes Other Regulatory Process Applicable?

Other Regulatory Process Number: (/u/4[] Yes Potential security impact per SY-AA-500-127?

If Yes, then Security Reviewer acceptance documented by cross discipline review below No 0i Yes Surveillance Coordinator Review Required?

If Yes, then Surveillance Coordinator Review documented by cross discipline review below Cross Discipline Reviews: (list below)-z, f.4 ,vt., Print Print Print Signature Data(~I2 _i__ReO Date Discipline or Org.Date Discipline or Org.Date Discipline or Org.Signature Signature 1-l auu-nlll "T IQ U SQR Approval indicates that all required Cross-Disciplinary reviews have been performed and the reviewers have signed this form. This procedure is technically and functionally accurate f r all functional area /(See ADAA-102)SOR Approval:ad

/0n --i 2a -Print end Sign Date Dsiln 2013 Annual Radioactive Effluent Release Report for TMI Enclosure 2 -Page 1 of 1 Process Control Program for Radioactive Wastes, Revision 8 RW-AA-100 (Revision 8 was issued on March 20, 2013) 1 RW-AA-1 00 e lamRevision 8 Ex l " Page 1 of 9 Nuclear Level 3 -Information Use PROCESS CONTROL PROGRAM FOR RADIOACTIVE WASTES 1. PURPOSE 1.1. The purpose of the Process Control Program (PCP) is to: 1.1.1. Establish the process and boundary conditions for the preparation of specific procedures for processing, sampling, analysis, packaging, storage, and shipment of solid radwaste in accordance with local, state, and federal requirements. (CM-1)1.1.2. Establish parameters which will provide reasonable assurance that all Low Level Radioactive Wastes (LLRW), processed by the in-plant waste process systems on-site OR by on-site vendor supplied waste processing systems, meet the acceptance criteria to a Licensed Burial Facility, as required by 10CFR Part 20, 1OCFR Part 61, 10CFR Part 71, 49CFR Parts 171-172, "Technical Position on Waste Form (Revision 1)" [1/91], "Low-Level Waste Licensing Branch Technical Position on Radioactive Waste Classification" [5/83], and the Station Technical Specifications, as applicable.

1.1.3. Provide reasonable assurance that waste placed in "on-site storage" meets the requirements as addressed within the Safety Analysis Reports for the low level radwaste storage facilities for dry and/or processed wet waste.2. TERMS AND DEFINITIONS 2.1. Process Control Program (PCP): The program which contains the current formulas, sampling, analysis, tests, and determinations to be made to ensure that processing and packaging of solid radioactive waste based on demonstrated processing of actual or simulated wet solid wastes will be accomplished in such a way as to assure the waste meets the stabilization criteria specified in 10CFR Parts 20, 61 and 71, state regulations, and burial site requirements.

2.2. Solidification:

Liquid waste processed to either an unstable or stable form per 1OCFR61 requirements.

Waste solidified does not have to meet the 300-year free standing monolith criteria.

Approved formulas, samples and tests do not have to meet NRC approval for wastes solidified in a container meeting stability criteria (e.g.High Integrity Container).

2.3. Stabilization:

Liquid waste processed to a "stable state" per 1OCFR61 Requirements.

Established formulas, samples, and tests shall be approved by the NRC in order to meet solidification "stabilization" criteria.

This processing method is currently not available, because the NRC recognizes that waste packed in a High Integrity Container meets the 300-year stabilization criteria.

In the event that this processing method becomes an acceptable method, then the NRC shall approve the stabilization formulas, samples, tests, etc.

I RW-AA-100 Revision 8 Page 2 of 9 2.4. Solidification Media: An approved media (e.g. Barnwell -vinyl ester styrene, cement, bitumen) when waste containing nuclides with greater than 5-year half lives is solidified in a container with activity greater than 1 micro curie/cc.

Waste solidified in a HIC is approved by the commission meeting the 10CFR61 stabilization criteria, including 1% free standing liquids by volume when the waste is packaged to a"stable" form and < 0.5% when waste is packaged to an "unstable" form. The formulas, sampling, analysis, and test do not require NRC approval, because the HIC meets the stability criteria.2.4.1. Solidification to an unstable or stable state is performed by vendors, when applicable.

Liquid waste solidified to meet stabilization criteria (1OCFR61 and 01-91 Branch Technical Requirements) shall have documentation available that demonstrates that the process is approved by the NRC or disposal facility.2.5. Dewatering:

The process of removing fluids from liquid waste streams to produce a waste form that meets the requirements of 10CFR Part 61 and applicable burial site criteria, <0.5% by volume when the waste is packaged to an "unstable" state, or<1% by volume when the waste is packaged to a "stable" form.2.6. High Integrity Container (HIC): A disposable container that is approved to the Requirements of 10CFR61. The use of HIC's is an alternative to solidification or encapsulation in a steel container to meet burial stability.

HIC's are used to package dewatered liquid wastes, (e.g. filter cartridges, filter media, resin, sludges, etc), or dry active waste.2.7. Encapsulation:

The process of placing a component (e.g. cartridge filters or mechanical components) into a special purpose disposable container and then completely surrounding the waste material with an approved stabilization media, such as cement.2.8. Liquid Waste Processing Systems: In-plant or vendor supplied processing systems consisting of equipment utilized for evaporation, filtration, demineralization, dewatering, compression dewatering, solidification, or reverse osmosis (RO) for the treatment of liquid wastes (such as Floor Drains, Chemical Drains and Equipment Drain inputs).2.9. Incineration, RVR, and/or Glass Vitrification of Liquid or Solid: Dry or wet waste processed via incineration and/or thermal processing where the volume is reduced by thermal means meets 1OCFR61 requirements.

2.10. Compaction:

When dry wastes such as paper, wood, plastic, cardboard, incinerator ash, and etc. are volume reduced through the use of a compactor.

2.11. Waste Streams: Consist of but are not limited to-Filter media (powdered, bead resin and fiber),-Filter cartridges,-Pre-coat body feed material,-Contaminated

charcoal, RW-AA-100 Revision 8 Page 3 of 9-Fuel pool activated hardware,-Oil Dry absorbent material added to a container to absorb liquids-Fuel Pool Crud-Sump and tank sludges,-High activity filter cartridges,-Concentrated liquids,-Contaminated waste oil,-Dried sewage or wastewater plant waste,-Dry Active Waste (DAW): Waste such as filters, air filters, low activity cartridge filters, paper, wood, glass, plastic, cardboard, hoses, cloth, and metals, etc, which have become contaminated as a consequence of normal operating, housekeeping and maintenance activities.

Other radioactive waste generated from cleanup of inadvertent contamination.

3. RESPONSIBILITIES 3.1. Implementation of this Process Control Program (PCP) is described in procedures at each station and is the responsibility of the each site to implement.
4. MAIN BODY 4.1. Process Control Proqram Requirements 4.1.1. A change to this PCP (Radioactive Waste Treatment Systems) may be made provided that the change is reported as part of the annual radioactive effluent release report, Regulatory Guide 1.21, and is approved by the Plant Operations Review Committee (PORC).4.1.2. Changes become effective upon acceptance per station requirements.

4.1.3. A solidification media, approved by the burial site, may be REQUIRED when liquid radwaste is solidified to a stable/unstable state.4.1.4. When processing liquid radwaste to meet solidification stability using a vendor supplied solidification system: 1. If the vendor has its own Quality Assurance (QA) Program, then the vendor shall ADHERE to its own QA Program and shall have SUBMITTED its process system topical report to the NRC or agreement state.2. If the vendor does not HAVE its own Quality Assurance Program, then the vendor shall ADHERE to an approved Quality Assurance Topical Report standard belonging to the Station or to another approved vendor.

RW-AA-100 Revision 8 Page 4 of 9 4.1.5. The vendor processing system(s) is/are controlled per the following:

1. A commercial vendor supplied processing system(s) may be USED for the processing of LLRW streams.2. Vendors that process liquid LLRW at the sites shall MEET applicable Quality Assurance Topical Report and Augmented Quality Requirements.

4.1.6. Vendor processing system(s) operated at the site shall be OPERATED and CONTROLLED in accordance with vendor approved procedures or station procedures based upon vendor approved documents.

4.1.7. All waste streams processed for burial or long term on-site storage shall MEET the waste classification and characteristics specified in 1 OCFR Part 61.55, Part 61.56, the 5-83 Branch Technical Position for waste classification, and the applicable burial site acceptance criteria (for any burial site operating at the time the waste was processed).

4.1.8. An Exelon Nuclear plant may store waste at another Exelon Nuclear plant, provided formal NRC approval has been RECEIVED for the transfer of waste.4.2. General Waste Processing Requirements NOTE: On-site resin processing involves tank mixing and settling, transferring to the station or vendor processing system via resin water slurry or vacuuming into approved waste containers, and, when applicable, dewatering for burial.4.2.1. Vendor resin beds may be USED for decontamination of plant systems, such as, SFP (Spent Fuel Pool), RWCU (reactor water cleanup), and SDC (Shut Down Cooling).

These resins are then PROCESSED via the station or vendor processing system.4.2.2. Various drains and sump discharges will be COLLECTED in tanks or suitable containers for processing treatment.

Water from these tanks may be SENT through a filter, demineralizer, concentrator or vendor supplied processing systems.4.2.3. Process waste (e.g. filter media, sludges, resin, etc) will be periodically DISCHARGED to the station or vendor processing system for onsite waste treatment or PACKAGED in containers for shipment to offsite vendor for volume reduction processing.

4.2.4. Process water (e.g. chemical, floor drain, equipment drain, etc.) may be SENT to either the site waste processing systems or vendor waste processing systems for further filtration, demineralization for plant re-use, or discharge.

4.2.5. All dewatering and solidification/stabilization will be PERFORMED by either utility site personnel or by on-site vendors or will be PACKAGED and SHIPPED to an off-site vendor low-level radwaste processing facility.

RW-AA-100 Revision 8 Page 5 of 9 4.2.6. Dry Active Waste (DAW) will be HANDLED and PROCESSED per the following:

1. DAW will be COLLECTED and SURVEYED and may be SORTED for compactable and non-compactable wastes.2. DAW may be packaged in containers to facilitate on-site pre-compaction and/or off-site vendor contract requirements.
3. DAW items may be SURVEYED for release onsite or offsite when applicable.
4. Contaminated filter cartridges will be PLACED into a HIC or will be ENCAPSULATED in an in-situ liner for disposal or SHIPPED to an offsite waste processor in drums, boxes or steel liners per the vendor site criteria for processing and disposal.4.2.7. Filtering devices using pre-coat media may be USED for the removal of suspended solids from liquid waste streams. The pre-coat material or cartridges from these devices may be routinely REMOVED from the filter vessel and discharged to a Filter Sludge Tank or Liner/HIC.

Periodically, the filter sludge may be DISCHARGED to the vendor processing system for waste treatment onsite or PACKAGED in containers for shipment to offsite vendor for volume reduction processing.

4.2.8. Activated hardware stored in the Spent Fuel Pools will be PROCESSED periodically using remote handling equipment and may then be PUT into a container for shipment or storage in the pool or loading the processed activated hardware into the Dry Cask storage system.4.2.9. High Integrity Containers (HIC): 1. For disposal at Barnwell, vendors supplying HIC's to the station shall PROVIDE a copy of the HIC Certificate of Compliance, which details specific limitations on use of the HIC.2. For disposal at Clive, vendors supplying HIC's to the station shall PROVIDE a copy of the HIC Certificate of Conformance, which details specific limitations on use of the HIC.3. Vendors supplying HIC's to the station shall PROVIDE a handling procedure which establishes guidelines for the utilization of the HIC. These guidelines serve to protect the integrity of the HIC and ensure the HIC is handled in accordance with the requirements of the Certificate of Compliance or Certificate of Conformance.

4.2.10. Lubricants and oils contaminated as a consequence of normal operating and maintenance activities may be PROCESSED on-site (by incineration, for oils meeting 10CFR20.2004 and applicable state requirements, or by an approved vendor process)or SHIPPED offsite (for incineration or other acceptable processing method).4.2.11. Former in-plant systems GE or Stock Drum Transfer Cart and Drum Storage Areas may be USED for higher dose DAW storage at Clinton, Dresden, Quad Cities, Braidwood and Byron.

F RW-AA-100 Revision 8 Page 6 of 9 4.2.13 Certain waste, including flowable solids from holding pond, oily waste separator, cooling tower basin and emergency spray pond, may be disposed of onsite under the provisions of a 10CFR20.2002 permit. Specific requirements associated with the disposal shall be incorporated into station implementing procedures. (CM-2)4.3. Burial Site Requirements 4.3.1. Waste sent directly to burial shall COMPLY with the applicable parts of 49CFR171-172, 10CFR61, 10CFR71, and the acceptance criteria for the applicable burial site.4.4. Shippingq and Inspection Requirements 4.4.1. All shipping/storage containers shall be INSPECTED, as required by station procedures, for compliance with applicable requirements (Department of Transportation (DOT), Nuclear Regulatory Commission (NRC), station, on-site storage, and/or burial site requirements) prior to use.4.4.2. Containers of solidified liquid waste shall be INSPECTED for solidification quality and/or dewatering requirements per the burial site, offsite vendor acceptance, or station acceptance criteria, as applicable.

4.4.3. Shipments sent to an off site processor shall be INSPECTED to ensure that the applicable processor's waste acceptance criteria are being met.4.4.4. Shipments sent for off site storage shall MEET the storage site's waste acceptance criteria.4.5. Inspection and Corrective Action 4.5.1. Inspection results that indicate non-compliance with applicable NRC, State, vendor, or site requirements shall be IDENTIFIED and TRACKED through the Corrective Action Program.4.5.2. Administrative controls for preventing unsatisfactory waste forms from being released for shipment are described in applicable station procedures.

If the provisions of the Process Control Program are not satisfied, then SUSPEND shipments of defectively packaged radioactive waste from the site. (CM-1)4.5.3. If freestanding water or solidification not meeting program requirements is observed, then samples of the particular series of batches shall be TAKEN to determine the cause. Additional samples shall be TAKEN, as warranted, to ensure that no freestanding water is present and solidification requirements are maintained.

4.6. Procedure and Process Reviews 4.6.1. The Exelon Nuclear Process Control Program and subsequent changes (other than editorial/minor changes) shall be REVIEWED and APPROVED in accordance with the station procedures, plant-specific Technical Specifications (Tech Spec), Technical Requirements Manual (T&RM), Operation Requirements Manual (ORM), as applicable, for the respective station and LS-AA-106.

Changes to the Licensees Controlled Documents, UFSAR, ORM, or TRM are controlled by the provisions of 10CFR 50.59.

RW-AA-100 Revision 8 Page 7 of 9 4.6.2. Any changes to the PCP shall be reviewed to determine if reportability is required in the Annual Radiological Effluent Release Report (ARERR). The Radwaste Specialist shall ensure correct information is SUBMITTED to the ODCM program owner prior to submittal of the ARERR.4.6.3. Station processes, applicable site-specific cask manual procedures, or other vendor waste processing/operating procedures shall be approved per RM-AA-1 02-1006.Procedures related to waste manifests, shipment inspections, and container activity determinations are CONTROLLED by Radiation Protection Standard Procedures (RP-AA-600 Series).1. Site waste processing IS CONTROLLED by site operating procedures.

2. Liquid processed by vendor equipment shall be PERFORMED in accordance with vendor procedures.

4.7. Waste Types, Point of Generation, and Processing Method Methods of processing and individual vendors may CHANGE due to changing financial and regulatory options. The table below is a representative sample. It is not intended be all encompassing.

AVAILABLE WASTE WASTE STREAM POINTS OF GENERATION POEING M E PROCESSING METHODS Bead Resin Systems -Fuel Pool, Condensate, Dewatering, solidification to an Reactor Water Cleanup, Blowdown, unstable/stable state Equipment Drain, Chemical and Thermal Processing Volume Control Systems, Floor Drain, Maximum Recycle, Blowdown, Boric Free Release to a Land Fill Acid Recycling System, Vendor Supplied Processing Systems, and Portable Demin System Powdered Resin Systems -(Condensate System, Floor Dewatering, solidification to an Drain/Equipment Drain filtration, Fuel unstable/stable state Pool) Thermal Processing Concentrated Waste Waste generated from Site Solidification to an unstable/stable Evaporators resulting typically from the state Floor Drain and Equipment Drain Thermal Processing Systems ThermalProcessing Sludge Sedimentation resulting from various Dewatering, solidification to an sumps, condensers, tanks, cooling unstable/stable state tower, emergency spray pond, holding Thermal Processing pond, and oily waste separators Evaporation on-site or at an offsite processor On-site disposal per 10CFR20.2002 I permit RW-AA-100 Revision 8 Page 8 of 9 AVAILABLE WASTE WASTE STREAM POINTS OF GENERATION POEING ME PROCESSING METHODS Filter cartridges Systems -Floor/Equipment Drains, Dewatering, solidification to an Fuel Pool; cartridge filters are-typically unstable/stable state generated from clean up activities Processed by a vendor for volume within the fuel pool, torus, etc reduction Dry Active Waste Paper, wood, plastic, rubber, glass, Decon/Sorting for Free Release metal, and etc. resulting from daily Compaction/Super-compaction plant activities Thermal Processing by Incineration or glass vitrification Sorting for Free Release Metal melting to an ingot Contaminated Oil Oil contaminated with radioactive Solidification unstable state materials from any in-plant system. Thermal Processing by Incineration Free Release for recycling Drying Bed Sludge Sewage Treatment and Waste Water Free release to a landfill or burial Treatment Facilities Metals See DAW See DAW Irradiated Hardware Fuel Pool, Reactor Components Volume Reduction for packaging efficiencies

5. DOCUMENTATION 5.1.1. Records of reviews performed shall be retained for the duration of the unit operating license. This documentation shall contain: 1. Sufficient information to support the change together with the appropriate analyses or evaluations justifying the change, and 2. A determination which documents that the change will maintain the overall conformance of waste products to Federal (10CFR61 and the Branch Technical Position), State, or other applicable requirements, including applicable burial site criteria.6.6.1.REFERENCES Technical Specifications:

6.1.1. The details contained in Current Tech Specs (CTS) or Improved Technical Specifications (ITS), as applicable, in regard to the Process Control Program (PCP), are to be relocated to the Licensee Controlled Documents.

Some facilities have elected to relocate these details into the Operational Requirements Manual (ORM).Relocation of the description of the PCP from the CTS or ITS does not affect the safe operation of the facility.

Therefore, the relocation details are not required to be in the CTS or the ITS to provide adequate protection of the public health and safety.

RW-AA-100 Revision 8 Page 9 of 9 6.2. Writers'

References:

6.2.1. Code of Federal Regulations:

10 CFR Part 20, Part 61, Part 71, 49 CFR Parts 171-172 6.2.2. Low Level Waste Licensing Branch Technical Position on Radioactive Waste Classification, May 1983 6.2.3. Technical Position on Waste Form (Revision 1), January 1991 6.2.4. Branch Technical Position on Concentration Averaging and Encapsulation, January 1995 6.2.5. Regulatory Guide 1.21, Measuring Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive materials in Liquid and Gaseous Effluents from Light-Water-Cooled Nuclear Power Plants 6.2.6. I.E. Circular 80.18, 1OCFR 50.59 Safety Evaluation for Changes to Radioactive Waste Treatment Systems 6.3. Users'

References:

6.3.1. Quality Assurance Program (QATR)6.3.2. LS-AA-106, Plant Operations Review Committee 6.3.3. RM-AA-102-1006, Processing Vendor Documents 6.3.4. RP-AA-600 Series, Radioactive Material/Waste Shipments 6.3.5. CY-AA-170-2000, Annual Radioactive Effluent Release Report 6.4. Station Commitments:

6.4.1. Peach Bottom CM-1, T03819, Letter from G.A. Hunger, Jr., dated Sept. 29 1994, transmitting TSCR 93-16 (Improved Technical Specifications).

6.4.2. Limerick CM-2, T03896, 1OCFR20.2002 permit granted to Limerick via letter dated July 10, 1996.7. ATTACHMENTS

-None