ML072970036: Difference between revisions
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
StriderTol (talk | contribs) (StriderTol Bot change) |
||
(2 intermediate revisions by the same user not shown) | |||
Line 15: | Line 15: | ||
| page count = 52 | | page count = 52 | ||
}} | }} | ||
=Text= | =Text= | ||
{{#Wiki_filter:INITIAL LICENSE EXAM 2007 SCENARIO ONE Brunswick Steam Electric Plant, Unit No.2 BRUNSWICK JULY-AUG EXAM-325,324/2007-301 | {{#Wiki_filter:INITIAL LICENSE EXAM 2007 SCENARIO ONE Brunswick Steam Electric Plant, Unit No. 2 BRUNSWICK JULY-AUG EXAM - 325,324/2007-301 FINAL SIMULATOR SCENARIO (1 OF 4) | ||
FINAL SIMULATOR SCENARIO (1 OF 4) | |||
Facility: BRUNSWICK Scenario No.: 1 Op Test No.: 2007 NRC | Brunswick 2007 NRC Scenario 1 Page 1 of 2 | ||
* Facility: | |||
The plant is operating at 100%power, End of Cycle.No equipment is out of service Turnover: Swap RB Supply&Exhaust Fans from 2C to 20 for maintenance | Examiners: | ||
work.Maintenance | BRUNSWICK Scenario No.: | ||
personnel are standing by.Critical Task: See Scenario Summary Event Malf.No.Event Event Description | Operators: | ||
No.Type'" 1 N/A N-SRO Swap RB Supply and Exhaust Fans N-BOP 2 K4522A OFF C-SRO 2C RBCCW sheared shaft, 2B fails to auto start (AOP)C-BOP 3 RC026F C-SRO Runback of 2A Recirc Pump to Limiter#2.(TS)(AOP) | 1 Op Test No.: 2007 NRC (SRO) | ||
Penetration | (RO) | ||
X49A Line Break-Remote Shutdown Instrumentation | (BOP) | ||
is lost (TS)6 CN019F C-SRO AOG fails to isolate on High H2 signal CN011F I-BOP 7 EEOO9F M-ALL Loss of Offsite Power, DG3 Differential | Initial Conditions: The plant is operating at 100% power, End of Cycle. | ||
Fault, Reactor Scram (AOPs, DG026F EOPs)8 ES028F C-SRO HPCI injection valve fails to auto open C-RO 9 NBOO6F M-ALL Steam Leak in Drywell, Emergency Depressurization (EOPs)10 K1J36A C-SRO RHR Loop"B", drywell spray valve fails closed C-BOP 11 NB025F I-ALL Level instrument | No equipment is out of service Turnover: Swap RB Supply & Exhaust Fans from 2C to 20 for maintenance work. | ||
failure, Reference leg flashing, Reactor Flooding required...(N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor | Maintenance personnel are standing by. | ||
N/O | Critical Task: See Scenario Summary Event Malf. No. Event Event Description No. Type'" | ||
ratings require comments;a comment sheet is attached. | 1 N/A N-SRO Swap RB Supply and Exhaust Fans N-BOP 2 K4522A OFF C-SRO 2C RBCCW sheared shaft, 2B fails to auto start (AOP) | ||
C-BOP 3 RC026F C-SRO Runback of 2A Recirc Pump to Limiter #2. (TS) (AOP) | |||
Unit 2 is operating at maximum power, End Of Cycle.A swap of RB Supply&Exhaust Fans will be required to support maintenance | * 4 5 | ||
activities. | N/A NB014F C-RO R-SRO R-RO TS-SRO Increase power following the runback. | ||
Following the swap of RB fans, RBCCW Pump 2C coupling fails and 2B RBCCW Pump will fail to Auto-Start | Instrument Penetration X49A Line Break - Remote Shutdown Instrumentation is lost (TS) 6 CN019F C-SRO AOG fails to isolate on High H2 signal CN011F I-BOP 7 EEOO9F M-ALL Loss of Offsite Power, DG3 Differential Fault, Reactor Scram (AOPs, DG026F EOPs) 8 ES028F C-SRO HPCI injection valve fails to auto open C-RO 9 NBOO6F M-ALL Steam Leak in Drywell, Emergency Depressurization (EOPs) 10 K1J36A C-SRO RHR Loop "B", drywell spray valve fails closed C-BOP 11 NB025F I-ALL Level instrument failure, Reference leg flashing, Reactor Flooding required | ||
on pressure, but will be able to be manually started.After restart of the 2B RBCCW Pump, Reactor Recirculation | ... (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor | ||
Pump 2A will runback to Limiter#2.After addressing | * NOTES: 1) 2) | ||
the Technical Specifications | = | ||
and discussions | S Satisfactory; | ||
with I&C, the 2A Recirculation | ... =Critical Task/Step U - Unsatisfactory; = | ||
Pump Limiter#2 signal will be reset and power returned to the pre-event level.A Reactor Instrument | N/O Not Observed All Unsatisfactory ratings require comments; a comment sheet is attached. | ||
Penetration | |||
line break occurs (X49A)and the line is isolated affecting instrument | Brunswick 2007 NRC Scenario 1 Page 2 of 2 | ||
N026B for Remote Shutdown Panel Level Indication | * SCENARIO DESCRIPTION Unit 2 is operating at maximum power, End Of Cycle. | ||
R604BX.Technical Specifications | A swap of RB Supply & Exhaust Fans will be required to support maintenance activities. | ||
must be addressed. | Following the swap of RB fans, RBCCW Pump 2C coupling fails and 2B RBCCW Pump will fail to Auto-Start on pressure, but will be able to be manually started. | ||
After TS are addressed, AOG will receive a high-high H2 signal due to a failed hydrogen detector and will fail to isolate requiring manual isolation by the BOP.Off-Site Power will be lost.DG4 will auto start and tie to E4.DG3 will auto start and briefly tie to E3, but will then trip on overcurrent | After restart of the 2B RBCCW Pump, Reactor Recirculation Pump 2A will runback to Limiter #2. | ||
and E3 will be unavailable. | After addressing the Technical Specifications and discussions with I&C, the 2A Recirculation Pump Limiter #2 signal will be reset and power returned to the pre-event level. | ||
E1 and E3 cannot be cross-tied | A Reactor Instrument Penetration line break occurs (X49A) and the line is isolated affecting instrument N026B for Remote Shutdown Panel Level Indication R604BX. Technical Specifications must be addressed. After TS are addressed, AOG will receive a high-high H2 signal due to a failed hydrogen detector and will fail to isolate requiring manual isolation by the BOP. | ||
due to the overcurrent | Off-Site Power will be lost. DG4 will auto start and tie to E4. DG3 will auto start and briefly tie to E3, but will then trip on overcurrent and E3 will be unavailable. E1 and E3 cannot be cross-tied due to the overcurrent lockout. If the crew attempts to crosstie E7 and E8 the cross-tie breaker at E8 will fail. The loss of E3/E7 results in loss of level transmitters N026A and N027A. HPCI and RCIC are available for RPV level control. SRVs are available for pressure control. The HPCI injection valve will fail to auto open but can be manually opened. Additionally, RBCCW cooling will be shifted to conventional service water. 120V Panels 2-AB, 2-AB-RX and 32AB will be transferred to alternate. | ||
lockout.If the crew attempts to crosstie E7 and E8 the cross-tie breaker at E8 will fail.The loss of E3/E7 results in loss of level transmitters | A steam leak will occur in the drywell. Drywell coolers will trip and the RHR Loop "B" drywell spray valve (E11-F016B) cannot be opened causing drywell temperature to rise above 300°F requiring emergency depressurization (CRITICAL TASK). Following emergency depressurization reactor pressure and drywell reference leg temperature will be in the unsafe region of the RPV saturation limit The only available level instruments (N004A. N004C, N036 and N027B) will begin to exhibit indications of reference leg flashing. With no valid indication of RPV level, the crew will enter the Reactor Flooding Procedure. | ||
N026A and | The crew will increase available injection to maximum until at least 5 SRVs are open and Reactor pressure is at least 50 psig above suppression chamber pressure (Minimum Reactor Flooding Pressure) (CRITICAL TASK). Once these conditions are established the crew will throttle flow to maintain at least the required 50 psig differential but as low as possible. | ||
service water.120V Panels 2-AB, 2-AB-RX and 32AB will be transferred | When RPV flooding conditions have been established, the scenario may be terminated . | ||
to alternate. | * NOTES: 1) | ||
A steam leak will occur in the drywell.Drywell coolers will trip and the RHR Loop"B" drywell spray valve (E11-F016B) | : 2) * | ||
cannot be opened causing drywell temperature | = | ||
to rise above 300°F requiring emergency depressurization (CRITICAL TASK).Following emergency depressurization | S Satisfactory; | ||
reactor pressure and drywell reference leg temperature | =Critical Task/Step U - Unsatisfactory; = | ||
will be in the unsafe region of the RPV saturation | N/O Not Observed All Unsatisfactory ratings require comments; a comment sheet is attached. | ||
limit The only available level instruments (N004A.N004C, N036 and N027B)will begin to exhibit indications | * PROGRESS ENERGY CAROLINAS BRUNSWICK TRAINING SECTION 2007 NRC EXAM SCENARIO #1 | ||
of reference leg flashing.With no valid indication | * 2007 NRC Examination Scenario #1 | ||
of RPV level, the crew will enter the Reactor Flooding Procedure. | * SCENARIO DESCRIPTION Unit Two (2) is operating at maximum power, End Of Cycle. | ||
The crew will increase available injection to maximum until at least 5 SRVs are open and Reactor pressure is at least 50 psig above suppression | A swap of RB Supply & Exhaust Fans will be required to support maintenance activities. | ||
chamber pressure (Minimum Reactor Flooding Pressure)(CRITICAL TASK).Once these conditions | Following the swap of RB fans, RBCCW Pump 2C coupling fails and 2B RBCCW Pump will fail to Auto-Start on pressure, but will be able to be manually started. | ||
are established | After starting of the 2B RBCCW Pump, Reactor Recirculation Pump 2A will run back to Limiter #2. After addressing the Technical Specifications and discussions with I&C, the 2A Recirculation Pump Limiter #2 signal will be reset and power returned to the pre-event level. | ||
the crew will throttle flow to maintain at least the required 50 psig differential | A Reactor Instrument Penetration line break occurs (X49A) and the line is isolated affecting instrument N026B for Remote Shutdown Panel Level Indication R604BX. | ||
but as low as possible.When RPV flooding conditions | Technical Specifications must be addressed. After TS are addressed, AOG will receive a high-high H2 signal due to a failed hydrogen detector and will fail to isolate requiring manual isolation by the BOP. | ||
have been established, the scenario may be terminated | Off-Site Power will be lost. DG4 will auto start and tie to E4. DG3 will auto start and briefly tie to E3, but will then trip on overcurrent and E3 will be unavailable. E1 and E3 cannot be cross-tied due to the overcurrent lockout. If the crew attempts to crosstie E7 and E8 the cross-tie breaker at E8 will fail. The loss of E3/E7 results in loss of level transmitters N026A and N027A. HPCI and RCIC are available for RPV level control. | ||
SRVs are available for pressure control. The HPCI injection valve will fail to auto open but can be manually opened. Additionally, RBCCW cooling will be shifted to conventional service water. 120V Panels 2-AB, 2AB-RX and 32AB will be transferred to alternate. | |||
N/O | A steam leak will occur in the drywell. Drywell coolers will trip and the RHR Loop "B" drywell spray valve (E11-F016B) cannot be opened causing drywell temperature to rise above 300°F requiring emergency depressurization (CRITICAL TASK). Following emergency depressurization reactor pressure and drywell reference leg temperature will be in the unsafe region of the RPV saturation limit The only available level instruments (N004A, N004C, N036 and N027B) will begin to exhibit indications of reference leg flashing. With no valid indication of RPV level, the crew will enter the Reactor Flooding Procedure. | ||
ratings require comments;a comment sheet is attached. | * 2007 NRC Examination Scenario #1 2 | ||
* SCENARIO DESCRIPTION (continued) | |||
Scenario#1 | The crew will increase available injection to maximum until at least 5 SRVs are open and Reactor pressure is at least 50 psig above suppression chamber pressure (Minimum Reactor Flooding Pressure) (CRITICAL TASK). Once these conditions are established the crew will throttle flow to maintain at least the required 50 psig differential but as low as possible. | ||
When RPV flooding conditions have been established, the scenario may be terminated. | |||
Unit Two (2)is operating at maximum power, End Of Cycle.A swap of RB Supply&Exhaust Fans will be required to support maintenance | * 2007 NRC Examination Scenario #1 3 | ||
activities. | |||
Following the swap of RB fans, RBCCW Pump 2C coupling fails and 2B RBCCW Pump will fail to Auto-Start | SIMULATOR SETUP Initial Conditions IC 188 Scenario #1 ENP 24 for IC 14 Rx Pwr 100% | ||
on pressure, but will be able to be manually started.After starting of the 2B RBCCW Pump, Reactor Recirculation | Core Age EOC EVENTS EVENTS Event Trigger Trigger Description Number 1 NA NA Swap RB Supply & Exhaust Fans 2 1 Manual 2C RBCCW Pump Sheared shaft. 2B fails to auto start 3 2 Manual Runback of 2A Recirculation Pump to Limiter #2 4 NA NA Increase power following runback reset 5 3 Manual Penetration X49A Line Break ,B21-N026B fails upscale | ||
Pump 2A will run back to Limiter#2.After addressing | -~ | ||
the Technical Specifications | 12 Manual AOG Failure to isolate on high hydrogen signal 4 Manual Loss Of Off-Site Power. DG #3 Differential Fault, Reactor Scram 8 NA NA HPCI injection valve fails to auto open 9 Steam Leak In The Drywell. Emergency Depressurization 5 Manual 10 RHR Loop "B" drywell spray valve fails to open 11 Level Instrument failure. Reference Leg flashing. Reactor NA NA Flooding required 2007 NRC Examination Scenario #1 4 | ||
and discussions | |||
with I&C, the 2A Recirculation | SIMULATOR SETUP Interventions Summary (Shaded entries = Active) | ||
Pump Limiter#2 signal will be reset and power returned to | Malfunctions Summary Malf 10 Mult Description Current Target Rmptime Actime Dactime Trig 10 Value Value ES028F HPCIINJ VLV FAILS AUTO OPEN True True EE009F LOSS OF OFF-SITE POWER False True 4 DG026F DG3 DIFFERENTIAL FAULT True True NB006F A MSL BREAK BEFORE FLOW 0 4.00 00:05:00 5 RESTRICTOR RC026F RECIRC PMP "A" RUNBACK TO False True 00:00:05 2 LIMITER #2 NB014F Penetration X49A Line Break False True 3 NB025F REF LEG FLASHING True True CN019F AOG ISOL VLV FAILS TO AUTO True True CLOSE CN011F AOG B SYS ISOLATES False True 12 Remotes Summary Remf 10 Mult Description Current Target Rmptime Actime Trig 10 Value Value EP_IACS993P OW CLR A & 0 OVERRIDE - NORMAL STOP 00:03:00 6 NORMAUSTOP EP_IACS994P OW CLR A & 0 OVERRIDE - NORMAL STOP 00:03:00 6 NORMAUSTOP SWJAVSW193 SW-V193 MAN ISOL NSW TO RBCCW OPEN CLOSE 00:04:00 8 SW_VHSW146L CONV SW TO RBCCW HSX V146 SHUT OPEN 00:04:00 8 RP_IARPSB RESTART RPS MG SET B NORMAL RESET 00:03:00 9 RP_IAEPAMGB RPS M-G SET B EPA BKRS SET SET 00:03:00 9 ED_ZIEDH08 PNL 2AB PWR (E7=NORM/E8=ALT) NORMAL ALT 00:02:00 7 ED_ZIEDH11 PNL 2AB-RX PWR (E7=NORM/E8=ALT) NORMAL ALT 00:02:00 7 ED_ZIEDHXO PNL 32AB PWR (E7=NORM/E8=ALT) NORMAL ALT 00:02:00 7 2007 NRC Examination Scenario #1 5 | ||
Penetration | * TaglD SIMULATOR SETUP Override Summary Description Position/ | ||
line break occurs (X49A)and the line is isolated affecting instrument | Tarqet Actual Value Override Value Rmptime Actime Dactime Trig K1J36A CONT SPRAY VLV E11-F016B AUTO OFF OFF K1J36A CONT SpRAy VLVE11-F016B . CLOse ON ON K1J36A CONT SPRAY VLV E11-F016B OpeN OFF OFf K4522A RBCCW PMP C AUTO ON ON OFF 1 K4522LG4 RBCCW PMP C OFF G ON/OFF OFF OFF 1 K4522RR4 RBCCW PMP CON R ON/OFF ON ON 1 K4521A RBCCW PMP B AUTO AUTO ON OFF 1 K2712A SCOOP TUBE A RESET NORMAL ON ON K2712A SCOOP TUBE A RESET RESET OFF OFF K2712A SCOOP TUBE A RESET TRIP OFF OFF Annunciator Summary Window Description Taqname Override Type Oval AVal Actime Dactime Triq NONE | ||
N026B for Remote Shutdown Panel Level Indication | * Batch Files File NRC SCENARIO S-1.BAT Trigger Description NONE Special Instructions Load scenario file 2007 NRC Scenario 1.scn Ensure ENP-24 for IC-14 @ P603. | ||
R604BX.Technical Specifications | Copy Batch File NRC SCENARIO S-1.bat from memory stick E Drive to F Drive on bsimpcOO | ||
must be addressed. | * 2007 NRC Examination Scenario #1 6 | ||
After TS are addressed, AOG will receive a high-high H2 signal due to a failed hydrogen detector and will fail to isolate requiring manual isolation by the BOP.Off-Site Power will be lost.DG4 will auto start and tie to E4.DG3 will auto start and briefly tie to E3, but will then trip on overcurrent | * SHIFT BRIEFING Plant Status The plant is operating at maximum power, End of Cycle. | ||
and E3 will be unavailable. | Equipment Out of Service No equipment is out of service Plan of the Day Maintain current power. | ||
E1 and E3 cannot be cross-tied | Following shift turnover, Place the 20 RB Supply & Exhaust Fans in service and secure 2C Supply & Exhaust Fans. Maintenance personnel are standing by to perform PMs. No clearance is required . | ||
due to the overcurrent | * 2007 NRC Examination Scenario #1 7 | ||
lockout.If the crew attempts to crosstie E7 and E8 the cross-tie breaker at E8 will fail.The loss of E3/E7 results in loss of level transmitters | * SCENARIO INFORMATION Examiner Notes Procedures Used in Scenarios: | ||
N026A and | EVENT 1 | ||
service water.120V Panels 2-AB, 2AB-RX and 32AB will be transferred | * OP-37.1, Sect 8.9 EVENT 2 | ||
to alternate. | * Annunciator 2-UA-3, Window 2-5 (RBCCW Pump Disch Hdr Press Low) | ||
A steam leak will occur in the drywell.Drywell coolers will trip and the RHR Loop"B" drywell spray valve (E11-F016B) | * OAOP-16 EVENT 3/4 | ||
cannot be opened causing drywell temperature | * Annunciator 2-A-6, Window 3-2 (Recirc Pump Runback) | ||
to rise above 300°F requiring emergency depressurization (CRITICAL TASK).Following emergency depressurization | * 2AOP-04.0 (Low Core Flow) | ||
reactor pressure and drywell reference leg temperature | * 20P-02, Sect 5.3 (Speed/Power Increase Using the Recircirculation Pump Speed Control) | ||
will be in the unsafe region of the RPV saturation | * Procedure 20P-02, Section 8.3 (Recovery from Recirculation Pump Runback) | ||
limit The only available level instruments (N004A, N004C, N036 and N027B)will begin to exhibit indications | * Technical Specification 3.4.1 (Recirculation Pump Runback - Single Loop) | ||
of reference leg flashing.With no valid indication | EVENT 5 | ||
of RPV level, the crew will enter the Reactor Flooding Procedure.2007 NRC Examination | * Unit 2 Technical Specifications, 3.6.1.3 & 3.3.3.2 | ||
Scenario#1 2 | * 01-44 , Excess Flow Check Valve Position Indication Evaluation | ||
* Annunciator 2-UA-24 1-3, Pen X49B Elev 86'-0" Azimuth 225 degrees) | |||
The crew will increase available injection to maximum until at least 5 SRVs are open and Reactor pressure is at least 50 psig above suppression | EVENT 6 | ||
chamber pressure (Minimum Reactor Flooding Pressure)(CRITICAL TASK).Once these conditions | * Annunciator UA-45 2-1, Discharge H2 Conc Hi-Hi | ||
are established | * Annunciator UA-45 2-2, Discharge H2 Conc Hi | ||
the crew will throttle flow to maintain at least the required 50 psig differential | * Annunciator UA-48-5-4, AOG System Bypass | ||
but as low as possible.When RPV flooding conditions | * ODCM 7.3.10 EVENT 7 | ||
have been established, the scenario may be terminated. | * 2EOP-01-RSP (REACTOR SCRAM PROCEDURE) | ||
2007 NRC Examination | * 2EOP-01-RVCP (REACTOR VESSEL CONTROL PROCEDURE) | ||
Scenario#1 3 | * OAOP-36.1 | ||
SIMULATOR SETUP Initial Conditions | * OEOP-02-PCCP EVENT 8 | ||
IC 188 Scenario#1 ENP 24 for IC 14 Rx Pwr 100%Core Age EOC EVENTS EVENTS Event Trigger Trigger Description | * 001-01.02, Sect 5.10.7, Conduct of Operations EVENT 9/10 | ||
Number 1 NA NA Swap RB Supply&Exhaust Fans 2 1 Manual 2C RBCCW Pump Sheared shaft.2B fails to auto start 3 2 Manual Runback of 2A Recirculation | * OEOP-01-SEP-03, Torus Sprays | ||
Pump to Limiter#2 4 NA NA Increase power following runback reset 5 3 Manual Penetration | * OEOP-01-SEP-02, Drywell Sprays | ||
X49A Line Break ,B21-N026B | * 2EOP-01-RVCP (REACTOR VESSEL CONTROL PROCEDURE) | ||
* OEOP-02-PCCP(PRIMARY CONTAINMENT CONTROL PROCEDURE) 2007 NRC Examination Scenario #1 8 | |||
Fault, Reactor Scram 8 NA NA HPCI injection valve fails to auto open 9 | * Procedures Used in Scenarios (continued): | ||
10 RHR Loop"B" drywell spray valve fails to open 11 | EVENT 11 | ||
failure.Reference Leg flashing.Reactor Flooding required 2007 NRC Examination | * OEOP-01-RXFP (REACTOR FLOODING PROCEDURE) | ||
Scenario#1 4 | Critical Tasks Perform emergency depressurization when drywell average temperature cannot be restored and maintained below 300°F. | ||
SIMULATOR SETUP Interventions | Establish and maintain RPV pressure at least 50 psig above suppression chamber pressure with at least 5 SRVs open. | ||
Summary (Shaded entries=Active)Malfunctions | * 2007 NRC Examination Scenario #1 9 | ||
Summary Malf 10 Mult Description | * EVENT 1 SHIFT TURNOVER, SWAPPING OF RB SUPPLY & EXHAUST FANS The crew swaps RB HVAC Fans per SCO direction Malfunctions required - None Objectives: | ||
Current Target Rmptime Actime Dactime Trig 10 Value Value | SCO - Directs BOP to shift from the 2C to the 2D RB Supply & Exhaust Fans to support Maintenance BOP - Starts 2D RB HVAC Fans & removes 2C fans from service per 20P-37.1 Section 8.9 Success Path: | ||
FAULT True True NB006F A MSL BREAK BEFORE FLOW 0 4.00 00:05:00 5 RESTRICTOR | RB HVAC Supply & Exhaust Fans fans 2A, B, D in service, 2C secured. | ||
RC026F RECIRC PMP"A" RUNBACK TO False True 00:00:05 2 LIMITER#2 NB014F Penetration | Simulator Operator Activities: | ||
X49A Line Break False True 3 NB025F REF LEG FLASHING True True | * When asked, as the Reactor Building Auxiliary Operator, report that pre-start checks on RB HVAC Fans have been completed When asked, as the RBAO, report that the fans appear to be operating normally. | ||
Current Target Rmptime Actime Trig | * When asked as the RBAO report that the MSIV Pit Dampers are open. | ||
EP_IACS993P OW CLR A&0 OVERRIDE-NORMAL STOP 00:03:00 6 NORMAUSTOP | * 2007 NRC Examination Scenario #1 10 | ||
EP_IACS994P OW CLR A&0 OVERRIDE-NORMAL STOP 00:03:00 6 NORMAUSTOP | * EVENT 1 SHIFT TURNOVER/SWAPPING OF RB SUPPLY & EXHAUST FANS Required Operator Actions Normal Operation - Swapping of RB Supply & Exhaust Fans SRO | ||
SWJAVSW193 | * Directs BOP to shift from the 2C to the 20 RB Supply & Exhaust Fans to support Maintenance BOP | ||
SW-V193 MAN ISOL NSW TO RBCCW OPEN CLOSE 00:04:00 8 SW_VHSW146L | * Places 20 RB HVAC Fans in service & removes 2C fans from service per 20P-37.1 Section 8.9 APPLICANT'S ACTIONS OR BEHAVIOR: | ||
CONV SW TO RBCCW HSX V146 SHUT OPEN 00:04:00 8 RP_IARPSB RESTART RPS MG SET B NORMAL RESET 00:03:00 9 RP_IAEPAMGB RPS M-G SET B EPA BKRS SET SET 00:03:00 9 ED_ZIEDH08 | * 2007 NRC Examination Scenario #1 11 | ||
PNL 2AB PWR (E7=NORM/E8= | * EVENT 2 START RBCCW PUMP COUPLING FAILURE/PUMP in AUTO FAILS TO AUTO The crew responds to a problem on one of the operating RBCCW Pumps Malfunctions required: | ||
* 2B RBCCW Pump will fail to auto-start on a low RBCCW discharge header pressure | |||
PNL 2AB-RX PWR (E7=NORM/E8= | * Coupling failure modification Objectives: | ||
SCO - Directs BOP to enter and execute OAOP-16.0: RBCCW System Failure BOP - Refers to 2-UA-3 2-5 and OAOP-16.0 to respond to the 2C Pump issue and 2B Pump failure to start Success Path: | |||
PNL 32AB PWR (E7=NORM/E8= | 2B RBCCW Pump is manually started (by placing its control switch to ON) and RBCCW is returned to normal operation (normal discharge pressure). | ||
Simulator Operator Activities: | |||
Scenario#1 5 | * WHEN directed by lead examiner, activate TRIGGER 1 (2C RBCCW Pump Coupling Failure) | ||
* | * WHEN asked, as the RBAO, report that the 2C RBCCW appears to have a broken coupling. Motor is running but pump is not turning | ||
Position/Actual Override Rmptime Actime Dactime Trig | * WHEN asked, as I&C, acknowledge request to investigate 2B RBCCW pump failure to start | ||
K1J36A CONT SPRAY VLV E11-F016B AUTO OFF OFF K1J36A CONT SpRAy VLVE11-F016B | * 2007 NRC Examination Scenario #1 12 | ||
.CLOse ON ON K1J36A CONT SPRAY VLV E11-F016B OpeN OFF OFf K4522A RBCCW PMP C AUTO ON ON OFF 1 K4522LG4 RBCCW PMP C OFF G ON/ | * EVENT 2 RBCCW PUMP COUPLING FAILURE/PUMP in AUTO FAILS TO AUTO START Required Operator Actions Transient Response - Entry into OAOP-16.0: Failure of RBCCW System SRO | ||
Summary Window Description | * Directs BOP operator to enter annunciator response and refers to OAOP-16.0 | ||
Taqname Override Type Oval AVal Actime Dactime Triq NONE Batch Files File | * Directs start of 2B RBCCW pump | ||
NRC SCENARIO S-1.BAT NONE Special Instructions | * Directs Maintenance to investigate 2B RBCCW pump auto start failure | ||
Load scenario file 2007 NRC Scenario 1.scn Ensure ENP-24 for IC-14@P603.Copy Batch File NRC SCENARIO S-1.bat from memory stick E Drive to F Drive on bsimpcOO 2007 NRC Examination | * Notifies Maintenance of 2C RBCCW Pump coupling failure | ||
Scenario#1 6 | * Directs BOP to remove 2C RBCCW Pump from service BOP | ||
* Refers to Annunciator Response 2-UA-3 2-5 (RBCCW Disch Header Press Lo) | |||
personnel are standing by to perform PMs.No clearance is required.2007 NRC Examination | * May Reference OAOP-16 | ||
Scenario#1 7 | * Places 2C RBCCW Pump switch to 'off' | ||
* | * Manually starts 2B RBCCW Pump | ||
Examiner Notes Procedures | * Verifies RBCCW System is operating normally BOP/RO | ||
Used in Scenarios: | * Dispatches AO to investigate cause of RBCCW low pressure | ||
EVENT 1*OP-37.1, Sect 8.9 EVENT 2*Annunciator | * 2007 NRC Examination Scenario #1 13 | ||
2-UA-3, Window 2-5 (RBCCW Pump Disch Hdr Press Low)*OAOP-16 EVENT 3/4*Annunciator | * EVENT 2 START RBCCW PUMP COUPLING FAILURE/PUMP in AUTO FAILS TO AUTO APPLICANT'S ACTIONS OR BEHAVIOR: | ||
2-A-6, Window 3-2 (Recirc Pump Runback)*2AOP-04.0 (Low Core Flow)*20P-02, Sect 5.3 (Speed/Power | * 2007 NRC Examination Scenario #1 14 | ||
Increase Using the Recircirculation | * EVENT 3 2A REACTOR RECIRCULATION PUMP RUNBACK TO LIMITER #2 The crew responds to a spurious runback of the 2A Recirculation Pump speed controller to Speed Limiter #2. The scoop tube lockup circuit is defeated. (can not be locked up) | ||
Pump Speed Control)*Procedure 20P-02, Section 8.3 (Recovery from Recirculation | Malfunction required: | ||
Pump Runback)*Technical Specification | * 2A Reactor Recirculation MG Set will experience a spurious runback signal to the Limiter #2 setpoint (approx 49% speed) | ||
3.4.1 (Recirculation | * Lockout circuit on scoop tube will be defeated (override) | ||
Pump Runback-Single Loop)EVENT 5*Unit 2 Technical Specifications, 3.6.1.3&3.3.3.2*01-44 , Excess Flow Check Valve Position Indication | |||
Evaluation | |||
*Annunciator | |||
2-UA-24 1-3, Pen X49B Elev 86'-0" Azimuth 225 degrees)EVENT 6*Annunciator | |||
UA-45 2-1, Discharge H2 Conc Hi-Hi*Annunciator | |||
UA-45 2-2, Discharge H2 Conc Hi*Annunciator | |||
UA-48-5-4, AOG System Bypass*ODCM 7.3.10 EVENT 7*2EOP-01-RSP (REACTOR SCRAM PROCEDURE) | |||
*2EOP-01-RVCP (REACTOR VESSEL CONTROL PROCEDURE) | |||
*OAOP-36.1*OEOP-02-PCCP | |||
EVENT 8*001-01.02, Sect 5.10.7, Conduct of Operations | |||
EVENT 9/10*OEOP-01-SEP-03, Torus Sprays*OEOP-01-SEP-02, Drywell Sprays*2EOP-01-RVCP (REACTOR VESSEL CONTROL PROCEDURE) | |||
*OEOP-02-PCCP(PRIMARY | |||
CONTAINMENT | |||
CONTROL PROCEDURE) | |||
2007 NRC Examination | |||
Scenario#1 8 | |||
Used in Scenarios (continued): | |||
EVENT 11*OEOP-01-RXFP (REACTOR FLOODING PROCEDURE) | |||
Critical Tasks Perform emergency depressurization | |||
when drywell average temperature | |||
cannot be restored and maintained | |||
below 300°F.Establish and maintain RPV pressure at least 50 psig above suppression | |||
chamber pressure with at least 5 SRVs open.2007 NRC Examination | |||
Scenario#1 9 | |||
*EVENT 1 SHIFT TURNOVER, SWAPPING OF RB SUPPLY&EXHAUST FANS | |||
required-None Objectives: | |||
SCO-Directs BOP to shift from the 2C to the 2D RB Supply&Exhaust Fans to support Maintenance | |||
BOP-Starts 2D RB HVAC Fans&removes 2C fans from service per 20P-37.1 Section 8.9 Success Path: RB HVAC Supply&Exhaust Fans fans 2A, B, D in service, 2C secured.Simulator Operator Activities: | |||
*When asked, as the Reactor Building Auxiliary Operator, report | |||
Scenario#1 10 | |||
*EVENT 1 SHIFT TURNOVER/SWAPPING | |||
OF RB SUPPLY&EXHAUST FANS | |||
ACTIONS OR BEHAVIOR: 2007 NRC Examination | |||
Scenario#1 11 | |||
*EVENT 2 START RBCCW PUMP COUPLING FAILURE/PUMP | |||
in AUTO FAILS TO AUTO | |||
required:*2B RBCCW Pump will fail to auto-start | |||
on a low RBCCW discharge header pressure*Coupling failure modification | |||
Objectives: | Objectives: | ||
SCO | SCO Directs RO to enter and execute 2AOP-04.0: Low Core Flow and refer to annunciator response for 2-A-6 3-2. | ||
Evaluates Technical Specification (T.S. 3.4.1.A.) requirements for single Recirculation Loop operation (flow mismatch requires declaration of the loop with the lower speed Recirculaton Pump as Inoperable) | |||
* Following determination of the Runback signal being spurious, directs reset of the 2A Reactor Recirculation Pump Limiter #2 signal and to return power to the pre-event power level RO Enters 2AOP-04.0 to respond to the 2A Reactor Recirculation MG runback Refers to Annunciator response for 2-A-6 3-2 "Recirc Flow "A" Limit (Immediate Action-diagnoses time is required) May attempt to lock scoop tube during runback if speed is still lowering. | |||
When directed by the SCO, resets the Runback signal per 20P-02, Section 8.3 Inserts control rods to get below the MELLL line per ENP-24 Success Path: | |||
The runback condition on the 2A Reactor Recirculation Pump is identified, 2AOP-04.0 is entered and executed, power level is stabilized, Technical Specification requirements are evaluated for single Recirculation Loop operation, and the Runback Signal is successfully reset per 20P-02.0 following resolution . | |||
* 2007 NRC Examination Scenario #1 15 | |||
* EVENT 3 2A REACTOR RECIRCULATION PUMP RUNBACK TO LIMITER #2 Simulator Operator Activities: | |||
* WHEN directed by the lead examiner, activate TRIGGER 2 (2A Recirc Pump runback to Limiter #2) | |||
* WHEN asked, as the Turbine Building Auxiliary Operator (TBAO), wait 3 minutes and report that there are no apparent problems at the 2A Reactor Recirculation Motor Generator. | |||
* WHEN asked, as I&C, wait 5 minutes and report that the cause of the Runback to Limiter #2 was due to an error in installation of a jumper during the performance of a surveillance currently in progress (the I&C technician was supposed to be on Unit One). | |||
* WHEN asked, as I&C, report that the lockout circuit has been repaired and all testing by OPERATIONS is complete, there is no additional testing required for the scoop tube lock. The runback may be reset at this time. | |||
* WHEN asked, as NE, provide guidance on moving under MELLL and state that the rod pattern does not need to be symmetrical. | |||
* 2007 NRC Examination Scenario #1 16 | |||
* EVENT 3 2A REACTOR RECIRCULATION PUMP RUNBACK TO LIMITER #2 Required Operator Actions Transient response - Entry into 2AOP-04.0: Low Core Flow SRO | |||
* Directs RO to enter and execute 2AOP-04.0: Low Core Flow. Also directs referring to Annunciator Response 2-A-6 3-2 Recirc Flow "A" Limit | |||
* Contacts I&C for support NOTE: SRO may direct RO to lower the unaffected Recirc Pump speed within allowable mismatch. If needed technical specification determination may be postponed until after the scenario for this event. | |||
Evaluates Technical Specification (T.S. 3.4.1.A) | |||
Tech Spec 3.4.1 Two Recirc Loop operation with matched flows not met. | |||
A. Align APLHGR, MCPR, and APRM simulated Thermal Power High trip functions for single loop operation (6 hours) | |||
* requirements for single Recirculation Loop operation (flow mismatch requires declaration of the loop with the lower speed Recirculaton Pump as Inoperable, Tech. Spec bases.) | |||
* Following determination of the Runback signal being spurious, directs reset of the 2A Reactor Recirculation Pump Limiter #2 signal to return of power to the pre-event power level | |||
* Directs RO to insert control rods to get below the MELLL line on the power to flow map. | |||
* Contacts NE for guidance | |||
* 2007 NRC Examination Scenario #1 17 | |||
* EVENT 3 2A REACTOR RECIRCULATION PUMP RUNBACK TO LIMITER #2 Required Operator Actions (continued) | |||
RO | |||
* Refers to Annunciator response for 2-A-6 3-2 ''Recirc Flow "A" Limit | |||
* (Immediate Action-diagnoses time is required) May attempt to lock scoop tube during runback if speed is still lowering. | |||
* When directed by the SCO, resets the Runback signal per 20P-02, Section 8.3 | |||
* Inserts control rods to get below the MELLL line per ENP-24 RO/BOP | |||
* Enters 2AOP-04.0 to respond to the 2A Reactor Recirculation MG runback | |||
* If greater than 15% power change, contact Chemistry for coolant samples. | |||
APPLICANT'S ACTIONS OR BEHAVIOR: | |||
* 2007 NRC Examination Scenario #1 18 | |||
* EVENT 4 INCREASING POWER FOLLOWING RUNBACK SIGNAL RESET The crewwill take action to restore reactor power to the pre-runback level. | |||
Malfunctions required: | |||
None Objectives: | |||
SCO Directs RO to raise reactor power to 90% by raising Recirculation Flow on "An Loop RO Raises reactor power per 20P-02.0, section 5.3, by raising "An Recirculation Pump Speed Success Path: | |||
Reactor power is raised to approximately the pre-runback level. | |||
Simulator Operator Activities: | Simulator Operator Activities: | ||
WHEN asked, as the Nuclear Engineer, report that power may be raised without ramp limitations, to 90% to clear the loop mismatch, using Reactor Recirculation flow. Then, predicts will have to be run prior to pulling rods. IF the unaffected loop was lowered to clear the mismatch request raising the lower speed pump to match speeds then balance flow adjustments to 90%, then predicts will have to be run prior to pulling rods. | |||
* 2007 NRC Examination Scenario #1 19 | |||
* Required Operator Actions Normal Operating Procedures - 20P-02 | |||
Scenario#1 | ****EVALUATOR NOTE: Alternate Power Verification is required at 10% power increments during power ascension and takes approximately 10 minutes to complete. If a change to the Gain Adjustment Factor (GAF) is required following Alternate Power Verification, an additional 15 minutes should be allowed. | ||
* | At the evaluator's discretion, prompt may be given stating that Alternate Power Verifications are to be completed by other members of the operating crew and are satisfactory. | ||
SRO | |||
* Contacts Load dispatcher regarding power increase | |||
* Direct RO to raise reactor power to 90% using 20P-02 RO | |||
* | |||
* When directed, raises reactor power to approximately 90% using Reactor Recirculation Flow per 20P-02.0 . | |||
* 2007 NRC Examination Scenario #1 20 | |||
* EVENT 4 INCREASING POWER FOLLOWING RUNBACK SIGNAL RESET APPLICANT'S ACTIONS OR BEHAVIOR: | |||
* 2007 NRC Examination Scenario #1 21 | |||
* EVENT 5 INSTRUMENT LINE PENETRATION FAILS The crew will observe and report the parameter changes impacted by the instrument failure. The SCO will diagnose the failure and evaluate the impact to plant operation, including Technical Specification action statement(s). | |||
Scenario#1 | Malfunctions required: | ||
* Penetration X49A Level instrument B21-N026B will fail. | |||
ACTIONS OR BEHAVIOR: 2007 NRC Examination | |||
Scenario#1 | |||
*EVENT | |||
required: | |||
Objectives: | Objectives: | ||
SCO - Diagnose the failure of the level instrument and evaluate the impact of the loss in TS (3.6.1.3 - Primary Containment Isolation Valves (PCIVs), 3.3.3.1 - Post Accident Monitoring (PAM) Instrumentation and 3.3.3.2 - Remote Shutdown Monitoring Instrumentation- 30 days). | |||
Success Path: | |||
SCO correctly evaluates the impact of the loss of the instrumentation, including the correct Technical Specification action statement. | |||
SCO-Diagnose the failure of the level instrument | |||
and evaluate the impact of the loss in TS (3.6.1.3-Primary Containment | |||
Isolation Valves (PCIVs), 3.3.3.1-Post Accident Monitoring (PAM)Instrumentation | |||
and 3.3.3.2-Remote Shutdown Monitoring | |||
Instrumentation- | |||
30 days).Success Path: SCO correctly evaluates the impact of the loss of the instrumentation, including the correct Technical Specification | |||
action statement. | |||
Simulator Operator Activities: | Simulator Operator Activities: | ||
*WHEN directed by the lead examiner, activate TRIGGER 3 (Instrument | * WHEN directed by the lead examiner, activate TRIGGER 3 (Instrument line break, B21-N026B fails). | ||
line break, B21-N026B fails).*IF directed to investigate | * IF directed to investigate penetration wait 3 minutes and report there is some evidence of a leak but you cannot determine the source. | ||
penetration | * 2007 NRC Examination Scenario #1 22 | ||
wait 3 minutes and report there is some evidence of a leak but you cannot determine the source.2007 NRC Examination | * Required Operator Actions: | ||
Scenario#1 22 | seo | ||
* Evaluate the plant impact and Technical Specification requirements for the instruments affected Tech Spec 3.6.1.3.C One or more penetration flowpaths with one PCIV Primary Containment Isolation Valve) inoperable C.1 Isolate the affected flowpath by using at least one closed automatic valve, manual valve, or blind flange (12 hours for Excess Flow Check Valve) | |||
requirements | AND C.2 Verify isolated (every 31 days) | ||
for the instruments | Tech Spec 3.3.3.1 Post Accident Monitoring (PAM) | ||
affected Tech Spec 3.6.1.3.C One or | A.1 One or more Functions with one required channel inoperable (restore to Operable in 30 days) | ||
with one PCIV Primary Containment | Tech Spec 3.3.3.2 A.1 One or more required Functions inoperable (restore to Operable in 30 days) | ||
Isolation Valve)inoperable | BOP | ||
C.1 Isolate the affected flowpath by using at least one closed automatic valve, manual valve, or blind flange (12 hours for Excess Flow Check Valve)AND C.2 Verify isolated (every 31 days)Tech Spec 3.3.3.1 Post Accident Monitoring (PAM)A.1 One or more Functions with one required channel inoperable (restore to Operable in 30 days)Tech Spec 3.3.3.2 A.1 One or more required Functions inoperable (restore to Operable in 30 days)BOP*Refers to Annunciator | * Refers to Annunciator Response UA-24 1-3 "Pen X 49A ELEV 86'-0" AZIMUTH 225 degrees. | ||
Response UA-24 1-3"Pen X 49A ELEV 86'-0" AZIMUTH 225 degrees.2007 NRC Examination | * 2007 NRC Examination Scenario #1 23 | ||
Scenario#1 23 | * EVENT 5 INSTRUMENT LINE PENETRATION FAILS APPLICANT'S ACTIONS OR BEHAVIOR: | ||
*EVENT 5 INSTRUMENT | * 2007 NRC Examination Scenario #1 24 | ||
LINE PENETRATION | * EVENT 6 AOG FAILS TO ISOLATE ON HIGH H2 SIGNAL The crew will respond to the AOG failure to isolate. | ||
FAILS APPLICANT'S | Malfunctions required: | ||
ACTIONS OR BEHAVIOR: | The H2 instrument 2-0G-AIT-4324 Stream1 will fail upscale. | ||
Scenario#1 24 | Objectives: | ||
SCO Directs BOP operator to respond to annunciators Evaluates ODCM for AOG bypassed BOP Reponds to annunciators Take manual actions to isolate AOG Success Path: | |||
required: The H2 instrument | AOG isolated Simulator Operator Activities: | ||
2-0G-AIT-4324 | * WHEN directed by lead examiner activate TRIGGER 12 (AOG failure to isolate on high-high H2 signal). | ||
Stream1 will fail upscale.Objectives: | * WHEN contacted as TBAO, to investigate status of the H2 detectors acknowledge and respond in 3 minutes that H2 instrument 2-0G-AIT-4324 Stream1 has failed upscale. | ||
SCO Directs BOP operator to respond to annunciators | * WHEN contacted as I&C to investigate failure, acknowledge only. | ||
Evaluates ODCM for AOG bypassed BOP Reponds to annunciators | * 2007 NRC Examination Scenario #1 25 | ||
Take manual actions to isolate AOG Success Path: AOG isolated Simulator Operator Activities: | * EVENT 6 AOG FAILS TO ISOLATE ON HIGH H2 SIGNAL Required Operator Actions: | ||
*WHEN directed by lead examiner activate TRIGGER 12( | seo | ||
to isolate on high-high H2 signal).*WHEN contacted as TBAO, to investigate | * Directs BOP to respond to annunciators 2-UA 45 2-1, DISCHARGE H2 CONC HI-HI 2-UA 45 2-2, DISCHARGE H2 CONC HI 2-UA 485-4, AOG SYSTEM BYPASS | ||
status of the H2 detectors acknowledge | * Evaluates impact of AOG bypassing at power: | ||
and respond in 3 minutes that H2 instrument | ODCM 7.3.10 Gaseous Radwaste Treatment System A.1 Place system in service when Main Condenser Air Ejector System is in operation (7 Days) | ||
2-0G-AIT-4324 Stream1 has failed upscale.*WHEN contacted as I&C to investigate | * Directs isolating AOG in accordance with the APP | ||
failure, acknowledge | * Contact I&C to investigate 2-0G-AIT-4324 Stream 1 failure and AOG failure to isolate. | ||
only.2007 NRC Examination | BOP | ||
Scenario#1 25 | * Responds to annunciators: | ||
*EVENT 6 AOG FAILS TO ISOLATE ON HIGH H2 SIGNAL | 2-UA 45 2-1, DISCHARGE H2 CONC HI-HI 2-UA 45 2-2, DISCHARGE H2 CONC HI 2-UA 485-4, AOG SYSTEM BYPASS | ||
2-UA 45 2-1, DISCHARGE H2 CONC HI-HI 2-UA 45 2-2, DISCHARGE H2 CONC HI 2-UA 485-4, AOG SYSTEM BYPASS*Evaluates impact of AOG bypassing at power: ODCM 7.3.10 Gaseous Radwaste Treatment System A.1 Place system in service when Main Condenser Air Ejector System is in operation (7 Days)*Directs isolating AOG in accordance | * Isolates AOG by manipulating valve control switches as required in | ||
with the APP*Contact I&C to investigate | 'annunciator response procedures.(XCV-148, 147, 143, 142, and 141 closed) | ||
2-0G-AIT-4324 Stream 1 failure and AOG failure to isolate.BOP*Responds to annunciators: | EXAMINER NOTE: Valves will not re-position until ALL FIVE (5) switches are in the CLOSED position . | ||
2-UA 45 2-1, DISCHARGE H2 CONC HI-HI 2-UA 45 2-2, DISCHARGE H2 CONC HI 2-UA 485-4, AOG SYSTEM BYPASS*Isolates AOG by manipulating | * 2007 NRC Examination Scenario #1 26 | ||
valve control switches as required in'annunciator | * EVENT 6 AOG FAILS TO ISOLATE ON HIGH H2 SIGNAL APPLICANT'S ACTIONS OR BEHAVIOR: | ||
response procedures.(XCV-148,147,143,142, and 141 closed)EXAMINER NOTE: Valves will not re-position | * 2007 NRC Examination Scenario #1 27 | ||
until ALL FIVE (5)switches are in the CLOSED position.2007 NRC Examination | * EVENT? REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE The crew will respond to a loss of off-site power resulting in a reactor scram and a corresponding failure of Emergency Diesel Generator #3 due to an electrical fault on Bus E3. | ||
Scenario#1 26 | Malfunctions required: | ||
*EVENT 6 AOG FAILS TO ISOLATE ON HIGH H2 SIGNAL APPLICANT'S | * Off-site power will be lost due to a grid disturbance resulting in a reactor scram. Immediately following the starting and synchronization of #3 Emergency Diesel Generator, an electrical fault will develop on Emergency Bus E3, resulting in a trip of #3 Diesel Generator and unavailability of the Emergency Bus E3. | ||
ACTIONS OR BEHAVIOR: | Objectives: | ||
Scenario#1 27 | SCO - Executes the Emergency Operating Procedures: Enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure (if Rx Press is >1060 psig or Rx Level cannot be restored and maintained >170") | ||
*EVENT?REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG#3 FAILURE | Directs the RO to control reactor and containment parameters o Control pressure using SRVs with a pressure band of 800-1000 psig o Control Level using HPCI/RCIC with a band of 170" to 200" Directs BOP to enter and execute AOP-36.1 in response to the loss of off-site power and Diesel Generator failure Contacts System Load Dispatcher to determine Distribution Grid status RO Responds to the reactor scram and takes actions to control level and pressure in the established control bands using HPCI, RCIC, and SRVs | ||
resulting in a reactor scram and a corresponding | * 2007 NRC Examination Scenario #1 28 | ||
failure of Emergency Diesel Generator#3 due to an electrical | * EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE Objectives (continued): | ||
fault on Bus E3.Malfunctions | BOP Report Electric Plant status o Loss of off-site power o DG #4 loaded to Bus E4 o DG #3 tripped due to overcurrent trip on bus o Performs AOP-36.1 actions based on transient response priorities, including but not limited to the following: | ||
required:*Off-site power will be lost due to a grid disturbance | Places PCB auto-reclosers to OFF Transfers 120v panels Pursues Service Air cross-tie Ensures 2B Nuclear Service Water Pump is running, starts 2B and 2C Conventional Pumps Starts Control Room and Battery Room HVAC Direct Transfer of RBCCW Cooling to Conventional Service Water Start 2B CRD Pump Direct RPS to be restarted Success Path: | ||
resulting in a reactor scram.Immediately | SCO successfully enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure and directs activities relating to reactor vessel control (RPV pressure and level) and directs activities relating to the loss of electrical power. RO takes actions to control reactor level and pressure (HPCI, RCIC, SRV operation). BOP enters OAOP-36.1 and takes actions, as directed to address the loss of electrical power. | ||
following the starting and synchronization | * 2007 NRC Examination Scenario #1 29 | ||
of#3 Emergency Diesel Generator, an electrical | * EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE Simulator Operator Activities | ||
fault will develop on Emergency Bus E3, resulting in a trip of#3 Diesel Generator and unavailability | * WHEN directed by lead examiner, activate TRIGGER 4 (Loss of offsite power, DG#3 failure) | ||
of the Emergency Bus E3.Objectives: | * IF contacted as Load Dispatcher, report that there has been storm damage to the Transmission Grid and that there is, currently, not a projected time for return to service. | ||
SCO-Executes the Emergency Operating Procedures: | * IF asked as Unit One (1) for permission to cross-tie air, grant permission. | ||
Enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure (if Rx Press is>1060 psig or Rx Level cannot be restored and maintained | * WHEN it is requested to cross-tie air, report Unit One (1) crosstie valve 1-SA-PV-5071 is open. | ||
>170")Directs the RO to control reactor and containment | * IF asked to transfer RCC to CSW, wait 4 minutes and activate TRIGGER 8. | ||
parameters | * IF asked to restart RPS, wait 3 minutes and activate TRIGGER 9. | ||
o Control pressure using SRVs with a pressure band of 800-1000 psig o Control Level using HPCI/RCIC with a band of 170" to 200" Directs BOP to enter and execute AOP-36.1 in response to the loss | * IF requested to transfer 2AB, 2AB-RX and 32AB to alternate, wait 2 minutes and activate TRIGGER 7. | ||
to determine Distribution | * | ||
Grid status RO Responds to the reactor scram and takes actions to control level and pressure in the established | * IF asked by I&C to investigate DG #3 failure, wait 3 minutes and report the EDG trip is due to an electrical lockout and is being investigated . | ||
control bands using HPCI, RCIC, and SRVs 2007 NRC Examination | * 2007 NRC Examination Scenario #1 30 | ||
Scenario#1 28 | * EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE Required Operator Actions SRO | ||
*EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG#3 FAILURE | * Executes the Emergency Operating Procedures: Enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure (if Rx Press is >1060 psig or Rx Level cannot be restored and maintained> 170") | ||
BOP Report Electric Plant status o Loss of off-site power o DG#4 loaded to Bus E4 o DG#3 tripped due to overcurrent | * Directs RO to perform Immediate Actions for SCRAM | ||
trip on bus o Performs AOP-36.1 actions based on transient response priorities, including but not limited to the following: | * Directs the RO to control reactor parameters o Control pressure using SRVs with a pressure band of 800-1000 psig (actions on SCRAM Hard Card) o Control Level using HPCI/RCIC with a band of 170" to 200" | ||
Places PCB auto-reclosers | * Directs BOP to enter and execute AOP-36.1 in response to the loss of off-site power and Diesel Generator failure o Directs E-Bus cross-tie at the 480V Buses (E7 to E8) | ||
to OFF Transfers 120v panels Pursues Service Air cross-tie Ensures 2B Nuclear Service Water Pump is running, starts 2B and 2C Conventional | * Contact System Load Dispatcher to determine Distribution Grid status | ||
Pumps Starts Control Room and Battery Room HVAC Direct Transfer of RBCCW Cooling to Conventional | * Enters and executes OEOP-02-PCCP when temperature exceeds 95°F in the Suppression Pool and directs RO to maximize Suppression Pool Cooling using RHR. | ||
Service Water Start 2B CRD Pump Direct RPS to be restarted Success Path: SCO successfully | RO | ||
enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure and directs activities | * Performs Scram Immediate Actions o Verify Scram Valves Open (full core display "Blue Lights") | ||
relating to reactor vessel control (RPV pressure and level)and directs activities | o All Rods In (Rod Worth Minimizer) o Trips Main Turbine o Places Reactor Mode Switch to Shutdown when total steam flow is | ||
relating to the loss of electrical | <3Mlbm/hr) meters on RTGB with "red" lines) o Verifies Heater Drain Pumps Tripped Inserts SRMs/IRMs (selects detectors and energizes circuit selects drive o | ||
power.RO takes actions to control reactor level and pressure (HPCI, RCIC, SRV operation). | pushbutton on RTGB left of rod select matrix) 2007 NRC Examination Scenario #1 31 | ||
BOP enters OAOP-36.1 and takes actions, as directed to address the loss of electrical | * EVENT? REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE Required Operator Actions (cont.) | ||
power.2007 NRC Examination | RO (cont.) | ||
Scenario#1 29 | * Verifies SCRAM Hard Card Actions | ||
*EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG#3 FAILURE | * Controls Reactor pressure using SRVs by placing various SRV control switches to "Open" and, subsequently, places switches back to Close/Auto to control Reactor pressure 800 psig to 1000 psig. | ||
*WHEN directed by lead examiner, activate TRIGGER 4 (Loss of offsite power, DG#3 failure)*IF contacted as Load Dispatcher, report that there has been storm damage to the Transmission | NOTE: If HPCI injection valve, 2-E41-F006, failure is found early level will be recovered and entry into RVCP will be later in scenario | ||
Grid and that there is, currently, not a projected time for return to service.*IF asked as Unit One (1)for | * If not automatically started, Starts HPCI/RCIC using the Hard Card to provide coolant injections for level control: | ||
air, grant permission. | o RCIC | ||
*WHEN it is requested to cross-tie air, report Unit One (1)crosstie | * Open E51-F046 | ||
DG#3 failure, wait 3 minutes and report the EDG trip is due to an electrical | * Start Barometric Vacuum Pump | ||
lockout and is being investigated | * Open E51-F045 | ||
* Open E51-F013 | |||
Scenario#1 30 | * Adjust RCIC flow controller to establish desired flow rate (pre-set value is 500 gpm) o HPCI | ||
*EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG#3 FAILURE | * Open E41-F059 | ||
Enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure (if Rx Press is>1060 psig or Rx Level cannot be restored and maintained> | * Start Vacuum Pump | ||
170")*Directs RO to perform Immediate Actions for SCRAM*Directs the RO to control reactor parameters | * Open E41-F001 | ||
o Control pressure using SRVs with a pressure band of 800-1000 psig (actions on SCRAM Hard Card)o Control Level using HPCI/RCIC with a band of 170" to 200"*Directs BOP to enter and execute AOP-36.1 in response to the loss of off-site power and Diesel Generator failure o Directs E-Bus cross-tie at the 480V Buses (E7 to E8)*Contact System Load Dispatcher | * Start Aux Oil Pump | ||
to determine Distribution | * Open E41-F006 (auto open on valve is failed, but valve will open when control switch is operated) | ||
Grid status*Enters and executes OEOP-02-PCCP | * Adjust Flow Controller to desired injection rate. | ||
when temperature | When directed, places "A" and "B" loops of RHR in Suppression Pool Cooling per the Hard Card . | ||
exceeds 95°F in the Suppression | * 2007 NRC Examination Scenario #1 32 | ||
Pool and directs RO to maximize Suppression | * EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE Required Operator Actions (cont.) | ||
Pool Cooling using RHR.RO*Performs Scram Immediate Actions o Verify Scram Valves Open (full core display"Blue Lights")o All Rods In (Rod Worth Minimizer) | RO (cont.) | ||
o Trips Main Turbine o Places Reactor Mode Switch to Shutdown when total steam flow is<3Mlbm/hr) | NOTE: Depending on availability, the BOP operator may perform the actions to place RHR in Suppression Pool Cooling. | ||
meters on RTGB with"red" lines)o Verifies Heater Drain Pumps Tripped | * Service Water o Opens SW-V105 ("B" loop) and SW-V101 ("A" loop) o Starts RHRSW Booster Pump (places control switch to start and throttles Open E11-F068 AlB) | ||
on RTGB left of rod select matrix)2007 NRC Examination | * RHR o If E11-F015A(B) is Open, closes E11-F017A(B) o Starts Loop A(B) RHR pump using control switch o Opens E11-F028A(B) o Throttles Open E11-F024A(B) | ||
Scenario#1 31 | * BOP o Throttles Closed E11-F048A(B) | ||
*EVENT?REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG#3 FAILURE | Recognizes and Reports Electric Plant status | ||
to control Reactor pressure 800 psig to 1000 psig.NOTE: If HPCI injection valve, 2-E41-F006, failure is found early level will be recovered and entry into RVCP will be later in scenario*If not automatically | -Loss of off-site power | ||
started, Starts HPCI/RCIC using the Hard Card to provide coolant injections | -DG #4 loaded to Bus E4 | ||
for level control: o RCIC*Open E51-F046*Start Barometric | -DG #3 tripped due to electrical lockout on the bus | ||
Vacuum Pump*Open E51-F045*Open E51-F013*Adjust RCIC flow controller | * Executes applicable steps of OAOP-36.1 in response to the loss of off-site power and failure of the #3 Emergency Diesel Generator and Emergency Bus E3. These actions include, but are not limited to the following: | ||
to establish desired flow | o Places PCB auto-reclosers to OFF o Directs field Operator to transfer 120v panel (2AB, 2AB-RX, and 32AB) o Directs field Operator to transfer RBCCW Cooling to Conventional Service Water 2007 NRC Examination Scenario #1 33 | ||
to desired injection rate.When directed, places"A" and"B" loops of RHR in Suppression | * EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE Required Operator Actions (cont.) | ||
Pool Cooling per the Hard Card.2007 NRC Examination | BOP (cont.) | ||
Scenario#1 32 | o Places RBCCW Pump control switches to OFF o Places Condensate Pump control switches to manual o Directs field Operator to cross-tie 480V Emergency Busses (E7 to E8) | ||
*EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG#3 FAILURE | * On a priority bases, executes any additional steps of OAOP-36.1 in response to the transient which might be applicable: | ||
Pool Cooling.*Service Water o Opens SW-V105 ("B" loop)and SW-V101 ("A" loop)o Starts RHRSW Booster Pump (places control switch to start and throttles Open E11-F068 AlB)*RHR o If E11-F015A(B) | o Restart of RPS MG Set o Pursues Service Air cross-tie o Ensures 2B Nuclear Service Water Pump is running, starts 2B and 2C Conventional Pumps o Starts Control Room and Battery Room HVAC o Starts 2B CRD Pump | ||
is Open, closes E11- | * 2007 NRC Examination Scenario #1 34 | ||
o Throttles Open E11-F024A(B) | * EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE APPLICANT'S ACTIONS OR BEHAVIOR: | ||
o Throttles Closed E11-F048A(B) | * 2007 NRC Examination Scenario #1 35 | ||
* EVENT 8 HPCIINJECTION VALVE FAILS TO OPEN The crew will respond to a failure of the HPCI injection valve to fail to automatically open on a valid initiation signal. | |||
and Reports Electric Plant status-Loss of off-site power-DG#4 loaded to Bus E4-DG#3 tripped due to electrical | Malfunctions required: | ||
lockout on the bus*Executes applicable | * The 2-E41-F006, HPCI Injection Valve, will fail to automatically open on a valid initiation signal Objectives: | ||
steps of OAOP-36.1 in response to the loss of off-site power and failure of the#3 Emergency Diesel Generator and Emergency Bus E3.These actions include, but are not limited to the following: | SCO/RO Identifies that the HPCI Injection Valve has failed to open on a valid initiation signal RO Opens the HPCI Injection Valve by taking the control switch to the "OPEN" position and commences injection with HPCI Success Path: | ||
o Places PCB auto-reclosers | HPCI injection is established at rated flow by operator action to open the HPCI injection valve. | ||
to OFF o Directs field Operator to transfer 120v panel (2AB, 2AB-RX, and 32AB)o Directs field Operator to transfer RBCCW Cooling to Conventional | * Simulator Operator Activities: | ||
Service Water 2007 NRC Examination | None Required Operator Actions: | ||
Scenario#1 33 | SRO/RO | ||
*EVENT 7 REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG#3 FAILURE | * Identifies the HPCI Injection Valve, 2-E41-F006, has failed to open on a valid initiation signal | ||
Pump control switches to manual o Directs field Operator to cross-tie 480V Emergency Busses (E7 to E8)*On a priority bases, executes any additional | * Directs RO to Open E41-F006 RO | ||
steps of OAOP-36.1 in response to the transient which might be applicable: | * Opens the 2-E41-F006 by taking the control switch to the "OPEN" position and establishes injection flow to the reactor from HPCI . | ||
o Restart of RPS MG Set o Pursues Service Air cross-tie o Ensures 2B Nuclear Service Water Pump is running, starts 2B and 2C Conventional | * 2007 NRC Examination Scenario #1 36 | ||
Pumps o Starts Control Room and Battery Room HVAC o Starts 2B CRD Pump 2007 NRC Examination | * EVENT 8 HPCIINJECTION VALVE FAILS TO OPEN APPLICANT'S ACTIONS OR BEHAVIOR: | ||
Scenario#1 34 | * 2007 NRC Examination Scenario #1 37 | ||
* EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION The crew will respond to a steam leak in the drywell in conjunction with a failure of the ability to spray the containment, subsequently leading to a requirement to Emergency Depressurize the reactor due to high drywell temperature. | |||
ACTIONS OR BEHAVIOR: 2007 NRC Examination | Malfunctions required: | ||
Scenario#1 35 | * A steam leak will occur in the drywell, resulting in elevated drywell temperatures | ||
*EVENT 8 HPCIINJECTION | * A failure will be inserted, preventing the opening of the "B" Loop Drywell Spray injection valve | ||
VALVE FAILS TO OPEN The crew will respond to a failure of the HPCI injection valve to fail to automatically | * Cross tie of E7 to E8 will not function Objectives: | ||
open on a valid initiation | SCO Recognize conditions of the steam leak in the drywell (elevated temperatures and pressures) and provide direction to the RO and BOP. | ||
signal.Malfunctions | Direct execution of applicable steps of OEOP-02-PCCP (Primary Containment Control Procedure). | ||
required:*The 2-E41-F006, HPCI Injection Valve, will fail to automatically | **** CRITICAL TASK*** When drywell temperature cannot be restored and maintained <300°F, direct Emergency Depressurization of the reactor Refer to Caution 1 and determine that the Reactor Saturation Graph will enter the "Unsafe" region during the depressurization RO/BOP Continue to maintain control of Reactor Water Level and Pressure, as directed by the SCO Must manually trip RCIC when High level trip setpoint is reached (206") | ||
open on a valid initiation | Place "B" Loop of RHR in Suppression Pool Cooling when directed Attempt to place "B" Loop in Suppression Chamber (SEP-03) and Drywell Sprays (SEP-02) when directed Identify and report failure of "B" Loop Drywell Spray valve to open and take actions to attempt to open the valve When directed, Emergency Depressurize the reactor (high drywell temperature) | ||
signal Objectives: | |||
SCO/RO | |||
that the HPCI Injection Valve has failed to open on a valid initiation | |||
signal Opens the HPCI Injection Valve by taking the control switch to the"OPEN" position and commences injection with HPCI Success Path: HPCI injection is established | |||
at rated flow by operator action to open the HPCI injection valve.*Simulator Operator Activities: | |||
None Required Operator Actions: SRO/RO*Identifies | |||
the HPCI Injection Valve, 2-E41-F006, has failed to open on a valid initiation | |||
by taking the control switch to the"OPEN" position and establishes | |||
injection flow to the reactor from HPCI.*2007 NRC Examination | |||
Scenario#1 36 | |||
*EVENT 8 HPCIINJECTION | |||
VALVE FAILS TO OPEN APPLICANT'S | |||
ACTIONS OR BEHAVIOR: | |||
Scenario#1 37 | |||
*EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION | |||
The crew will respond to a steam leak in the drywell in conjunction | |||
with a failure of the ability to spray the containment, subsequently | |||
leading to a requirement | |||
to Emergency Depressurize | |||
the reactor due to high drywell temperature. | |||
Malfunctions | |||
required:*A steam leak will occur in the drywell, resulting in elevated drywell temperatures*A failure will be inserted, preventing | |||
the opening of the"B" Loop Drywell Spray injection valve*Cross tie of E7 to E8 will not function Objectives: | |||
of the steam leak in the drywell (elevated temperatures | |||
and pressures) | |||
and provide direction to the RO and BOP.Direct execution of applicable | |||
steps of OEOP-02-PCCP (Primary Containment | |||
Control Procedure). | |||
****CRITICAL TASK***When drywell temperature | |||
cannot be restored and maintained | |||
<300°F, direct Emergency Depressurization | |||
of the reactor Refer to Caution 1 and determine that the Reactor Saturation | |||
Graph will enter the"Unsafe" region during the depressurization | |||
Pool Cooling when directed Attempt to place"B" Loop in Suppression | |||
Chamber (SEP-03)and Drywell Sprays (SEP-02)when directed Identify and report failure of"B" Loop Drywell Spray valve to open and take actions to attempt to open the valve When directed, Emergency Depressurize | |||
the reactor (high drywell temperature) | |||
Control injection from Low Pressure systems to maintain reactor water level during depressurization. | Control injection from Low Pressure systems to maintain reactor water level during depressurization. | ||
Success Path: When 300°F is exceeded in the drywell, the reactor is Emergency Depressurized | Success Path: | ||
and level is restored/maintained | When 300°F is exceeded in the drywell, the reactor is Emergency Depressurized and level is restored/maintained in the normal band (170" to 200") | ||
in the normal band (170" to 200")2007 NRC Examination | * 2007 NRC Examination Scenario #1 38 | ||
Scenario#1 | * EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION Simulator Operator Activities: | ||
***EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION | * WHEN directed by the lead examiner, activate TRIGGER 5 (Steam leak in drywell) | ||
* IF asked, report that the breaker for the 2-E11-F016B appears to have normal indication.. | |||
* IF asked, indicate reset of the thermal overload for 2-E11-F016B appears to have had no impact. | |||
* IF asked to manually open the 2-E11-F016B, report that the 2-E11-F016B is mechanically bound and will not open. | |||
* WHEN requested to lock-out drywell coolers, activate TRIGGER 6. | |||
* IF requested to support E7 to E8 cross-tie, acknowledge request. AFTER 5 minutes report racking mechanism on E7 cross-tie breaker has failed, maintenance has been notified for help. | |||
* Required Operator Action SRO | |||
* Recognize primary containment conditions (temperature rise and pressure rise) indicate a steam leak in the drywell. | |||
* Direct execution of applicable steps of OEOP-02-PCCP (Primary Containment Control Procedure). | |||
o Prior to Suppression Chamber Pressure exceeding 11.5 psig | |||
* Directs RO/BOP to perform Suppression Pool Spray per SEP-03 o When Suppression Chamber exceeds 11.5 psig, | |||
* Directs RO/BOP to perform Drywell Sprays per SEP-02 o Monitors Pressure Suppression Pressure to maintain in the SAFE region of the graph (utilizes ERFIS) o When Drywell air temperature exceeds 150°F | |||
* Directs RO/BOP to start all available drywell coolers (SEP-1 0 allowed) o Prior to Drywell air temperature exceeding 300°F | |||
* Directs RO/BOP to initiate Drywell Spray per SEP-02 | |||
* 2007 NRC Examination Scenario #1 39 | |||
* EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION Required Operator Action (continued) | |||
SRO (cont.) | |||
* **** CRITICAL TASK**** When drywell temperature cannot be restored and maintained <300°F, direct Emergency Depressurization of the reactor | |||
* Refer to Caution 1 and determine that the Reactor Saturation Graph will enter the "Unsafe" region during the depressurization | |||
* Other Primary Containment Control actions may be directed, but are non-consequential to the event. | |||
RO/BOP | |||
* Continue to maintain control of Reactor Water Level and Pressure, as directed by the SCO. | |||
* | |||
* When directed place "B" Loop of RHR in Suppression Pool Cooling o Service Water Opens SW-V105 ("B" loop) and SW-V101 ("A" loop) | |||
Starts RHRSW Booster Pump (places control switch to start and throttles Open E11-F068 AlB) o RHR | |||
* If E11-F015B is Open, closes E11-F0178 | |||
* Starts Loop B RHR pump using control switch | |||
* Opens E11-F028B | |||
* Throttles Open E11-F0248 | |||
* Throttles Closed E11-F048B | |||
* 2007 NRC Examination Scenario #1 40 | |||
* EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION Required Operator Action (continued) | |||
RO/BOP (cont.) | |||
* When directed place RHR in Suppression Chamber Sprays (SEP-03) o Places 2/3 Core Height Override Position to ON o Place Containment Spray Valve Control Switch to Manual o If E11-F015B is Open and RHR injection is not necessary, close E11-F017B o Start/Ensure a loop RHR pump is running o Open E11-F028B o Open E11-F027B o Ensure Loop is aligned to one of the following: LPCI, Suppression Pool Cooling, or Drywell Spray. | |||
* When directed to spray the Drywell per SEP-02 o Ensure Recirc Pumps are tripped o Ensure Drywell Coolers not running o Close E11-F024B o Verify in Safe region of Drywell Spray Initiation Graph o Ensure "B" loop RHR pump running o Open E11-F021 B o Open E11-F016B | |||
* Notifies SRO when it is recognized that the E11-F016B will not open | |||
* **** CRITICAL TASK**** When directed, Emergency Depressurize the Reactor by placing 7 ADS valve control switches to Open. | |||
* As Reactor pressure lowers, controls injection systems (RHR, Core Spray) to prevent overfilling by throttling loop injection valves and/or securing pumps as necessary. | |||
o RHR E11-F017A(B) o Core Spray E21-F005B NOTE: Indicated level will exceed 200 inches due to Emergency | |||
* Depressurization swell. | |||
2007 NRC Examination Scenario #1 41 | |||
* EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION APPLICANT'S ACTIONS OR BEHAVIOR: | |||
* 2007 NRC Examination Scenario #1 42 | |||
* EVENT 11 LEVEL INSTRUMENT FAILURE DUE TO REFERENCE LEG FLASHING | |||
- REACTOR FLOODING REQUIRED The crew will respond to indications of Reactor Pressure Vessel Level reference leg flashing, resulting in inability to determine reactor water level (entry condition for Reactor Flooding Procedure). | |||
Objectives: | |||
SCO As the reactor depressurizes, recognize indications of reference leg flashing resulting in no level instrumentation being available | |||
****CRITICAL TASK**** Enter and execute EOP-01-RxFP,Reactor Flooding Procedure, and establish Minimum Reactor Flooding Pressure. | |||
RO/SOP Implement directions given by SCO to establish required Reactor Flooding Conditions to ensure adequate core cooling Success Path: | |||
Reactor Pressure Vessel Injection has been established resulting in at least 5 safety relief valves (SRVs) being open with at least 50 psid (but as low as possible) between the Reactor and Suppression Chamber Pressure. | |||
Simulator Operator Activities: | Simulator Operator Activities: | ||
* | * None | ||
* 2007 NRC Examination Scenario #1 43 | |||
* EVENT 11 LEVEL INSTRUMENT FAILURE DUE TO REFERENCE LEG FLASHING | |||
- REACTOR FLOODING REQUIRED Required Operator Actions: | |||
EOP Action - Entry into and Execution of Reactor Flooding Procedure SCO ****CRITICAL TASK**** | |||
* As the reactor depressurizes, correctly evaluate indications to determine Level Instrument Reference Leg Flashing is occurring | |||
* Enter and execute EOP-01-RxFP, Reactor Flooding Procedure to ensure adequate core cooling | |||
* Determines 5 or more SRVs can be opened o Directs RO/80P to close 821 F022A-D (inbd MSIV's), 821-F028A-D (otbd MSIVs), E51-F0078 (RCIC), 821-F016/F019 (Drain bypasses) o Directs RO/80P to inject with RHR, Core Spray, CRD, and Alternate Cooling Injection Systems at maximum irrespective of NPSHNortex limits NOTE: If 5 or more SRVs can be Opened is answered NO, same steps, as above, except steam valve isolations are not directed. | |||
o When Reactor pressure is at least 50 psig above Suppression Chamber Pressure, direct that injection be controlled to maintain at least 5 SRVs open. | |||
RO/BOP | |||
* Observe and report indications of Reactor Vessel Level indication reference leg flashing | |||
* When directed, Close 821-F022A-D, 821-F028A-D, E51-F008, 821-F016/F019 by placing their control switches to Closed. | |||
* When directed starts some/all of the following systems in any order to establish 5 SRVs open and 50 psid between Reactor Vessel and Suppression Chamber. | |||
o "8" Core Spray Pump; ensures E21-F0048/F0058 opens o "C" RHR Pump; ensures E11-F015A1F017A opens o "8" and "D" RHR pumps; ensures E11-F0158/F0178 opens o If required, (ECCS pumps do not result in SRV opening) then starts LEP-01 systems (SLC injection) o Controls injection by throttling Core Spray Injection Valve (E21-F0058/RHR Injection Valves E11-F017A18) to maintain 5 SRVs open. | |||
2007 NRC Examination Scenario #1 44 | |||
* EVENT 11 LEVEL INSTRUMENT FAILURE DUE TO REFERENCE LEG FLASHING | |||
- REACTOR FLOODING REQUIRED APPLICANT'S ACTIONS OR BEHAVIOR: | |||
* 2007 NRC Examination Scenario #1 45 | |||
* Simulator Operator Activities: | |||
WHEN directed by the lead examiner, place the simulator in FREEZE. | |||
CAUTION DO NOT RESET THE SIMULATOR PRIOR TO RECEIPT OF CONCURRENCE TO DO SO FROM THE LEAD EXAMINER | |||
* 2007 NRC Examination Scenario #1 46 | |||
* RPV Level Transmitters (FIGURE 01.2-4 from SO-01 ) | |||
CR~50-to.50. 0 50-'0550-P60W ~sop | |||
~---t----j----I--:-I : | |||
I | |||
__ I Ot0210-U CR P604 1 P601 A I I | |||
* | I I | ||
I I | |||
I I | |||
I I | |||
Scenario#1 | I | ||
* CR P6D3 I | |||
I I | |||
,~----------------------------- | |||
C32~15O-210~ | |||
R606 B | |||
213 CORE HEIGHT. | |||
~ | |||
R615 CR J | |||
P601 5977 I | |||
INTERLOCK I I I | |||
L----------IN~I+----------- ... | |||
CR* CONTROL ROOM 2/3 CORE HEIGHT. . | |||
INTERLOCK - - - :~@-l LI RSi0 | |||
-150-to+ 150'" | |||
* 2007 NRC Examination Scenario #1 47 | |||
* ATTACHMENT 1 | |||
# Title - 2007 NRC Scenario 1 | |||
# Path - E:\NRC Simulator Dynamic Masters\NRC Scenario SCN files\2007 NRC Scenario 1.scn | |||
# Saved on 06-29-2007 at 16:03:28 mfi:ES028F,True,00:00:00,00:00:00, 0 mfi:NB014F,True,00:00:00,00:00:00,3 mfi:EE009F,True,00:00:00,00:00:00, 4 mfi:DG026F,True,00:00:00,00:00:00, 0 mfi:NB006F, 4,00:05:00,00:00:00,00:00:00, 5,A mfi:RC026F,True,00:00:00,00:00:05, 2 mfi:NB025F,True,00:00:00,00:00:00, 0 mfi:CN019F,True,00:00:00,00:00:00, 0 mfi:CN011 F,True,OO:OO:OO,OO:OO:OO, 12 rfi:EP_IACS993P,STOP,00:03:00, 6 rfi:EP_IACS994P,STOP,00:03:00, 6 rfi:SW_IAVSW193,CLOSE,00:04:00,8 rfi:SW_VHSW146L,OPEN,00:04:00, 8 rfi:RP_IARPSB,RESET,00:03:00, 9 rfi:RP_IAEPAMGB,SET,00:03:00, 9 rfi:ED_ZIEDH08,ALT,00:02:00, 1 rfi:ED_ZIEDH11,ALT,00:02:00, 7 rfi:ED_ZIEDHXO,ALT,00:02:00, 7 tri:10, K4522NWD tri:11, K2711 PS8 trc:10, batf:\nrc scenario s-1.bat trc:11, did:k2712a dii:K1 J36A,AUTO,OFF,00:00:00,00:00:00, 0 dii:K1 J36A,CLOSE,ON,00:00:00,00:00:00, 0 dii:K1 J36A,OPEN,OFF,00:00:00,00:00:00, 0 dii:K4522A,ON,OFF,00:00:00,00:00:00, 1 dii:K4521 A,AUTO,OFF,OO:OO:OO,OO:OO:OO, 1 doi:Q4522LG4,ON/OFF,OFF,00:00:00,00:00:00, 1 dii:K2712A,NORM,ON,00:00:00,00:00:00, ° doi:Q4522RR4,ON/OFF,ON,00:00:00,00:00:00, 1 dii:K2712A,RESET,OFF,00:00:00,00:00:00, 0 dii:K2712A,TRIP,OFF,00:00:00,00:00:00, 0 | |||
# TITLE - NRC Scenario S-1 | |||
# Path - E:\NRC Scenario S-1.bat | |||
* | # Saved on 6-29-2007 DOD:Q4522RR4 DOD:Q4522LG4 2007 NRC Examination Scenario #1 48 | ||
* WordPerfect Document Compare Summary Original document: P:\SES_CDP\MY_Templates\OPM SUMMARIES\OPM Summary Template_CRO_Final_rev2. wpd Revised document: @PFDesktop\:MyComputer\P:\SES_CDP\MY_Templates\OPM SUMMARIES\OPM Summary Template_CRO_Final_rev3.wpd Deletions are shown with the following attributes and color: | |||
Strikeout, Blue RGB(O,O,255). | |||
Deleted text is shown as full text. | |||
Insertions are shown with the following attributes and color: | |||
Double Underline, Redline, Red RGB(255,O,O). | |||
The document was marked with 57 Deletions, 61 Insertions, °Moves. | |||
*}} | |||
5 | |||
0 | |||
: | |||
, | |||
}} |
Latest revision as of 10:13, 13 March 2020
ML072970036 | |
Person / Time | |
---|---|
Site: | Brunswick ![]() |
Issue date: | 01/31/2007 |
From: | Progress Energy Carolinas |
To: | Office of Nuclear Reactor Regulation |
References | |
50-324/07-301, 50-325/07-301 50-324/07-301, 50-325/07-301 | |
Download: ML072970036 (52) | |
Text
INITIAL LICENSE EXAM 2007 SCENARIO ONE Brunswick Steam Electric Plant, Unit No. 2 BRUNSWICK JULY-AUG EXAM - 325,324/2007-301 FINAL SIMULATOR SCENARIO (1 OF 4)
Brunswick 2007 NRC Scenario 1 Page 1 of 2
- Facility:
Examiners:
BRUNSWICK Scenario No.:
Operators:
1 Op Test No.: 2007 NRC (SRO)
(RO)
(BOP)
Initial Conditions: The plant is operating at 100% power, End of Cycle.
No equipment is out of service Turnover: Swap RB Supply & Exhaust Fans from 2C to 20 for maintenance work.
Maintenance personnel are standing by.
Critical Task: See Scenario Summary Event Malf. No. Event Event Description No. Type'"
1 N/A N-SRO Swap RB Supply and Exhaust Fans N-BOP 2 K4522A OFF C-SRO 2C RBCCW sheared shaft, 2B fails to auto start (AOP)
C-BOP 3 RC026F C-SRO Runback of 2A Recirc Pump to Limiter #2. (TS) (AOP)
- 4 5
N/A NB014F C-RO R-SRO R-RO TS-SRO Increase power following the runback.
Instrument Penetration X49A Line Break - Remote Shutdown Instrumentation is lost (TS) 6 CN019F C-SRO AOG fails to isolate on High H2 signal CN011F I-BOP 7 EEOO9F M-ALL Loss of Offsite Power, DG3 Differential Fault, Reactor Scram (AOPs, DG026F EOPs) 8 ES028F C-SRO HPCI injection valve fails to auto open C-RO 9 NBOO6F M-ALL Steam Leak in Drywell, Emergency Depressurization (EOPs) 10 K1J36A C-SRO RHR Loop "B", drywell spray valve fails closed C-BOP 11 NB025F I-ALL Level instrument failure, Reference leg flashing, Reactor Flooding required
... (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor
- NOTES: 1) 2)
=
S Satisfactory;
... =Critical Task/Step U - Unsatisfactory; =
N/O Not Observed All Unsatisfactory ratings require comments; a comment sheet is attached.
Brunswick 2007 NRC Scenario 1 Page 2 of 2
- SCENARIO DESCRIPTION Unit 2 is operating at maximum power, End Of Cycle.
A swap of RB Supply & Exhaust Fans will be required to support maintenance activities.
Following the swap of RB fans, RBCCW Pump 2C coupling fails and 2B RBCCW Pump will fail to Auto-Start on pressure, but will be able to be manually started.
After restart of the 2B RBCCW Pump, Reactor Recirculation Pump 2A will runback to Limiter #2.
After addressing the Technical Specifications and discussions with I&C, the 2A Recirculation Pump Limiter #2 signal will be reset and power returned to the pre-event level.
A Reactor Instrument Penetration line break occurs (X49A) and the line is isolated affecting instrument N026B for Remote Shutdown Panel Level Indication R604BX. Technical Specifications must be addressed. After TS are addressed, AOG will receive a high-high H2 signal due to a failed hydrogen detector and will fail to isolate requiring manual isolation by the BOP.
Off-Site Power will be lost. DG4 will auto start and tie to E4. DG3 will auto start and briefly tie to E3, but will then trip on overcurrent and E3 will be unavailable. E1 and E3 cannot be cross-tied due to the overcurrent lockout. If the crew attempts to crosstie E7 and E8 the cross-tie breaker at E8 will fail. The loss of E3/E7 results in loss of level transmitters N026A and N027A. HPCI and RCIC are available for RPV level control. SRVs are available for pressure control. The HPCI injection valve will fail to auto open but can be manually opened. Additionally, RBCCW cooling will be shifted to conventional service water. 120V Panels 2-AB, 2-AB-RX and 32AB will be transferred to alternate.
A steam leak will occur in the drywell. Drywell coolers will trip and the RHR Loop "B" drywell spray valve (E11-F016B) cannot be opened causing drywell temperature to rise above 300°F requiring emergency depressurization (CRITICAL TASK). Following emergency depressurization reactor pressure and drywell reference leg temperature will be in the unsafe region of the RPV saturation limit The only available level instruments (N004A. N004C, N036 and N027B) will begin to exhibit indications of reference leg flashing. With no valid indication of RPV level, the crew will enter the Reactor Flooding Procedure.
The crew will increase available injection to maximum until at least 5 SRVs are open and Reactor pressure is at least 50 psig above suppression chamber pressure (Minimum Reactor Flooding Pressure) (CRITICAL TASK). Once these conditions are established the crew will throttle flow to maintain at least the required 50 psig differential but as low as possible.
When RPV flooding conditions have been established, the scenario may be terminated .
- NOTES: 1)
- 2) *
=
S Satisfactory;
Critical Task/Step U - Unsatisfactory;
N/O Not Observed All Unsatisfactory ratings require comments; a comment sheet is attached.
- PROGRESS ENERGY CAROLINAS BRUNSWICK TRAINING SECTION 2007 NRC EXAM SCENARIO #1
- 2007 NRC Examination Scenario #1
- SCENARIO DESCRIPTION Unit Two (2) is operating at maximum power, End Of Cycle.
A swap of RB Supply & Exhaust Fans will be required to support maintenance activities.
Following the swap of RB fans, RBCCW Pump 2C coupling fails and 2B RBCCW Pump will fail to Auto-Start on pressure, but will be able to be manually started.
After starting of the 2B RBCCW Pump, Reactor Recirculation Pump 2A will run back to Limiter #2. After addressing the Technical Specifications and discussions with I&C, the 2A Recirculation Pump Limiter #2 signal will be reset and power returned to the pre-event level.
A Reactor Instrument Penetration line break occurs (X49A) and the line is isolated affecting instrument N026B for Remote Shutdown Panel Level Indication R604BX.
Technical Specifications must be addressed. After TS are addressed, AOG will receive a high-high H2 signal due to a failed hydrogen detector and will fail to isolate requiring manual isolation by the BOP.
Off-Site Power will be lost. DG4 will auto start and tie to E4. DG3 will auto start and briefly tie to E3, but will then trip on overcurrent and E3 will be unavailable. E1 and E3 cannot be cross-tied due to the overcurrent lockout. If the crew attempts to crosstie E7 and E8 the cross-tie breaker at E8 will fail. The loss of E3/E7 results in loss of level transmitters N026A and N027A. HPCI and RCIC are available for RPV level control.
SRVs are available for pressure control. The HPCI injection valve will fail to auto open but can be manually opened. Additionally, RBCCW cooling will be shifted to conventional service water. 120V Panels 2-AB, 2AB-RX and 32AB will be transferred to alternate.
A steam leak will occur in the drywell. Drywell coolers will trip and the RHR Loop "B" drywell spray valve (E11-F016B) cannot be opened causing drywell temperature to rise above 300°F requiring emergency depressurization (CRITICAL TASK). Following emergency depressurization reactor pressure and drywell reference leg temperature will be in the unsafe region of the RPV saturation limit The only available level instruments (N004A, N004C, N036 and N027B) will begin to exhibit indications of reference leg flashing. With no valid indication of RPV level, the crew will enter the Reactor Flooding Procedure.
- 2007 NRC Examination Scenario #1 2
- SCENARIO DESCRIPTION (continued)
The crew will increase available injection to maximum until at least 5 SRVs are open and Reactor pressure is at least 50 psig above suppression chamber pressure (Minimum Reactor Flooding Pressure) (CRITICAL TASK). Once these conditions are established the crew will throttle flow to maintain at least the required 50 psig differential but as low as possible.
When RPV flooding conditions have been established, the scenario may be terminated.
- 2007 NRC Examination Scenario #1 3
SIMULATOR SETUP Initial Conditions IC 188 Scenario #1 ENP 24 for IC 14 Rx Pwr 100%
Core Age EOC EVENTS EVENTS Event Trigger Trigger Description Number 1 NA NA Swap RB Supply & Exhaust Fans 2 1 Manual 2C RBCCW Pump Sheared shaft. 2B fails to auto start 3 2 Manual Runback of 2A Recirculation Pump to Limiter #2 4 NA NA Increase power following runback reset 5 3 Manual Penetration X49A Line Break ,B21-N026B fails upscale
-~
12 Manual AOG Failure to isolate on high hydrogen signal 4 Manual Loss Of Off-Site Power. DG #3 Differential Fault, Reactor Scram 8 NA NA HPCI injection valve fails to auto open 9 Steam Leak In The Drywell. Emergency Depressurization 5 Manual 10 RHR Loop "B" drywell spray valve fails to open 11 Level Instrument failure. Reference Leg flashing. Reactor NA NA Flooding required 2007 NRC Examination Scenario #1 4
SIMULATOR SETUP Interventions Summary (Shaded entries = Active)
Malfunctions Summary Malf 10 Mult Description Current Target Rmptime Actime Dactime Trig 10 Value Value ES028F HPCIINJ VLV FAILS AUTO OPEN True True EE009F LOSS OF OFF-SITE POWER False True 4 DG026F DG3 DIFFERENTIAL FAULT True True NB006F A MSL BREAK BEFORE FLOW 0 4.00 00:05:00 5 RESTRICTOR RC026F RECIRC PMP "A" RUNBACK TO False True 00:00:05 2 LIMITER #2 NB014F Penetration X49A Line Break False True 3 NB025F REF LEG FLASHING True True CN019F AOG ISOL VLV FAILS TO AUTO True True CLOSE CN011F AOG B SYS ISOLATES False True 12 Remotes Summary Remf 10 Mult Description Current Target Rmptime Actime Trig 10 Value Value EP_IACS993P OW CLR A & 0 OVERRIDE - NORMAL STOP 00:03:00 6 NORMAUSTOP EP_IACS994P OW CLR A & 0 OVERRIDE - NORMAL STOP 00:03:00 6 NORMAUSTOP SWJAVSW193 SW-V193 MAN ISOL NSW TO RBCCW OPEN CLOSE 00:04:00 8 SW_VHSW146L CONV SW TO RBCCW HSX V146 SHUT OPEN 00:04:00 8 RP_IARPSB RESTART RPS MG SET B NORMAL RESET 00:03:00 9 RP_IAEPAMGB RPS M-G SET B EPA BKRS SET SET 00:03:00 9 ED_ZIEDH08 PNL 2AB PWR (E7=NORM/E8=ALT) NORMAL ALT 00:02:00 7 ED_ZIEDH11 PNL 2AB-RX PWR (E7=NORM/E8=ALT) NORMAL ALT 00:02:00 7 ED_ZIEDHXO PNL 32AB PWR (E7=NORM/E8=ALT) NORMAL ALT 00:02:00 7 2007 NRC Examination Scenario #1 5
- TaglD SIMULATOR SETUP Override Summary Description Position/
Tarqet Actual Value Override Value Rmptime Actime Dactime Trig K1J36A CONT SPRAY VLV E11-F016B AUTO OFF OFF K1J36A CONT SpRAy VLVE11-F016B . CLOse ON ON K1J36A CONT SPRAY VLV E11-F016B OpeN OFF OFf K4522A RBCCW PMP C AUTO ON ON OFF 1 K4522LG4 RBCCW PMP C OFF G ON/OFF OFF OFF 1 K4522RR4 RBCCW PMP CON R ON/OFF ON ON 1 K4521A RBCCW PMP B AUTO AUTO ON OFF 1 K2712A SCOOP TUBE A RESET NORMAL ON ON K2712A SCOOP TUBE A RESET RESET OFF OFF K2712A SCOOP TUBE A RESET TRIP OFF OFF Annunciator Summary Window Description Taqname Override Type Oval AVal Actime Dactime Triq NONE
- Batch Files File NRC SCENARIO S-1.BAT Trigger Description NONE Special Instructions Load scenario file 2007 NRC Scenario 1.scn Ensure ENP-24 for IC-14 @ P603.
Copy Batch File NRC SCENARIO S-1.bat from memory stick E Drive to F Drive on bsimpcOO
- 2007 NRC Examination Scenario #1 6
- SHIFT BRIEFING Plant Status The plant is operating at maximum power, End of Cycle.
Equipment Out of Service No equipment is out of service Plan of the Day Maintain current power.
Following shift turnover, Place the 20 RB Supply & Exhaust Fans in service and secure 2C Supply & Exhaust Fans. Maintenance personnel are standing by to perform PMs. No clearance is required .
- 2007 NRC Examination Scenario #1 7
- SCENARIO INFORMATION Examiner Notes Procedures Used in Scenarios:
EVENT 1
- OP-37.1, Sect 8.9 EVENT 2
- Annunciator 2-UA-3, Window 2-5 (RBCCW Pump Disch Hdr Press Low)
- OAOP-16 EVENT 3/4
- Annunciator 2-A-6, Window 3-2 (Recirc Pump Runback)
- 2AOP-04.0 (Low Core Flow)
- 20P-02, Sect 5.3 (Speed/Power Increase Using the Recircirculation Pump Speed Control)
- Procedure 20P-02, Section 8.3 (Recovery from Recirculation Pump Runback)
- Technical Specification 3.4.1 (Recirculation Pump Runback - Single Loop)
EVENT 5
- Unit 2 Technical Specifications, 3.6.1.3 & 3.3.3.2
- 01-44 , Excess Flow Check Valve Position Indication Evaluation
- Annunciator 2-UA-24 1-3, Pen X49B Elev 86'-0" Azimuth 225 degrees)
EVENT 6
- Annunciator UA-45 2-1, Discharge H2 Conc Hi-Hi
- Annunciator UA-45 2-2, Discharge H2 Conc Hi
- Annunciator UA-48-5-4, AOG System Bypass
- ODCM 7.3.10 EVENT 7
- 2EOP-01-RSP (REACTOR SCRAM PROCEDURE)
- 2EOP-01-RVCP (REACTOR VESSEL CONTROL PROCEDURE)
- OAOP-36.1
- OEOP-02-PCCP EVENT 8
- 001-01.02, Sect 5.10.7, Conduct of Operations EVENT 9/10
- OEOP-01-SEP-03, Torus Sprays
- OEOP-01-SEP-02, Drywell Sprays
- 2EOP-01-RVCP (REACTOR VESSEL CONTROL PROCEDURE)
- OEOP-02-PCCP(PRIMARY CONTAINMENT CONTROL PROCEDURE) 2007 NRC Examination Scenario #1 8
- Procedures Used in Scenarios (continued):
EVENT 11
- OEOP-01-RXFP (REACTOR FLOODING PROCEDURE)
Critical Tasks Perform emergency depressurization when drywell average temperature cannot be restored and maintained below 300°F.
Establish and maintain RPV pressure at least 50 psig above suppression chamber pressure with at least 5 SRVs open.
- 2007 NRC Examination Scenario #1 9
- EVENT 1 SHIFT TURNOVER, SWAPPING OF RB SUPPLY & EXHAUST FANS The crew swaps RB HVAC Fans per SCO direction Malfunctions required - None Objectives:
SCO - Directs BOP to shift from the 2C to the 2D RB Supply & Exhaust Fans to support Maintenance BOP - Starts 2D RB HVAC Fans & removes 2C fans from service per 20P-37.1 Section 8.9 Success Path:
RB HVAC Supply & Exhaust Fans fans 2A, B, D in service, 2C secured.
Simulator Operator Activities:
- When asked, as the Reactor Building Auxiliary Operator, report that pre-start checks on RB HVAC Fans have been completed When asked, as the RBAO, report that the fans appear to be operating normally.
- 2007 NRC Examination Scenario #1 10
- EVENT 1 SHIFT TURNOVER/SWAPPING OF RB SUPPLY & EXHAUST FANS Required Operator Actions Normal Operation - Swapping of RB Supply & Exhaust Fans SRO
- Places 20 RB HVAC Fans in service & removes 2C fans from service per 20P-37.1 Section 8.9 APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 11
- EVENT 2 START RBCCW PUMP COUPLING FAILURE/PUMP in AUTO FAILS TO AUTO The crew responds to a problem on one of the operating RBCCW Pumps Malfunctions required:
- Coupling failure modification Objectives:
SCO - Directs BOP to enter and execute OAOP-16.0: RBCCW System Failure BOP - Refers to 2-UA-3 2-5 and OAOP-16.0 to respond to the 2C Pump issue and 2B Pump failure to start Success Path:
2B RBCCW Pump is manually started (by placing its control switch to ON) and RBCCW is returned to normal operation (normal discharge pressure).
Simulator Operator Activities:
- WHEN asked, as the RBAO, report that the 2C RBCCW appears to have a broken coupling. Motor is running but pump is not turning
- 2007 NRC Examination Scenario #1 12
- EVENT 2 RBCCW PUMP COUPLING FAILURE/PUMP in AUTO FAILS TO AUTO START Required Operator Actions Transient Response - Entry into OAOP-16.0: Failure of RBCCW System SRO
- Directs BOP operator to enter annunciator response and refers to OAOP-16.0
- Directs start of 2B RBCCW pump
- Directs Maintenance to investigate 2B RBCCW pump auto start failure
- Refers to Annunciator Response 2-UA-3 2-5 (RBCCW Disch Header Press Lo)
- May Reference OAOP-16
- Places 2C RBCCW Pump switch to 'off'
- Manually starts 2B RBCCW Pump
- Verifies RBCCW System is operating normally BOP/RO
- 2007 NRC Examination Scenario #1 13
- EVENT 2 START RBCCW PUMP COUPLING FAILURE/PUMP in AUTO FAILS TO AUTO APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 14
- EVENT 3 2A REACTOR RECIRCULATION PUMP RUNBACK TO LIMITER #2 The crew responds to a spurious runback of the 2A Recirculation Pump speed controller to Speed Limiter #2. The scoop tube lockup circuit is defeated. (can not be locked up)
Malfunction required:
- 2A Reactor Recirculation MG Set will experience a spurious runback signal to the Limiter #2 setpoint (approx 49% speed)
- Lockout circuit on scoop tube will be defeated (override)
Objectives:
SCO Directs RO to enter and execute 2AOP-04.0: Low Core Flow and refer to annunciator response for 2-A-6 3-2.
Evaluates Technical Specification (T.S. 3.4.1.A.) requirements for single Recirculation Loop operation (flow mismatch requires declaration of the loop with the lower speed Recirculaton Pump as Inoperable)
- Following determination of the Runback signal being spurious, directs reset of the 2A Reactor Recirculation Pump Limiter #2 signal and to return power to the pre-event power level RO Enters 2AOP-04.0 to respond to the 2A Reactor Recirculation MG runback Refers to Annunciator response for 2-A-6 3-2 "Recirc Flow "A" Limit (Immediate Action-diagnoses time is required) May attempt to lock scoop tube during runback if speed is still lowering.
When directed by the SCO, resets the Runback signal per 20P-02, Section 8.3 Inserts control rods to get below the MELLL line per ENP-24 Success Path:
The runback condition on the 2A Reactor Recirculation Pump is identified, 2AOP-04.0 is entered and executed, power level is stabilized, Technical Specification requirements are evaluated for single Recirculation Loop operation, and the Runback Signal is successfully reset per 20P-02.0 following resolution .
- 2007 NRC Examination Scenario #1 15
- EVENT 3 2A REACTOR RECIRCULATION PUMP RUNBACK TO LIMITER #2 Simulator Operator Activities:
- WHEN directed by the lead examiner, activate TRIGGER 2 (2A Recirc Pump runback to Limiter #2)
- WHEN asked, as the Turbine Building Auxiliary Operator (TBAO), wait 3 minutes and report that there are no apparent problems at the 2A Reactor Recirculation Motor Generator.
- WHEN asked, as I&C, wait 5 minutes and report that the cause of the Runback to Limiter #2 was due to an error in installation of a jumper during the performance of a surveillance currently in progress (the I&C technician was supposed to be on Unit One).
- WHEN asked, as I&C, report that the lockout circuit has been repaired and all testing by OPERATIONS is complete, there is no additional testing required for the scoop tube lock. The runback may be reset at this time.
- WHEN asked, as NE, provide guidance on moving under MELLL and state that the rod pattern does not need to be symmetrical.
- 2007 NRC Examination Scenario #1 16
- EVENT 3 2A REACTOR RECIRCULATION PUMP RUNBACK TO LIMITER #2 Required Operator Actions Transient response - Entry into 2AOP-04.0: Low Core Flow SRO
- Directs RO to enter and execute 2AOP-04.0: Low Core Flow. Also directs referring to Annunciator Response 2-A-6 3-2 Recirc Flow "A" Limit
- Contacts I&C for support NOTE: SRO may direct RO to lower the unaffected Recirc Pump speed within allowable mismatch. If needed technical specification determination may be postponed until after the scenario for this event.
Evaluates Technical Specification (T.S. 3.4.1.A)
Tech Spec 3.4.1 Two Recirc Loop operation with matched flows not met.
A. Align APLHGR, MCPR, and APRM simulated Thermal Power High trip functions for single loop operation (6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br />)
- requirements for single Recirculation Loop operation (flow mismatch requires declaration of the loop with the lower speed Recirculaton Pump as Inoperable, Tech. Spec bases.)
- Following determination of the Runback signal being spurious, directs reset of the 2A Reactor Recirculation Pump Limiter #2 signal to return of power to the pre-event power level
- Directs RO to insert control rods to get below the MELLL line on the power to flow map.
- Contacts NE for guidance
- 2007 NRC Examination Scenario #1 17
- EVENT 3 2A REACTOR RECIRCULATION PUMP RUNBACK TO LIMITER #2 Required Operator Actions (continued)
- Refers to Annunciator response for 2-A-6 3-2 Recirc Flow "A" Limit
- (Immediate Action-diagnoses time is required) May attempt to lock scoop tube during runback if speed is still lowering.
- When directed by the SCO, resets the Runback signal per 20P-02, Section 8.3
- Inserts control rods to get below the MELLL line per ENP-24 RO/BOP
- If greater than 15% power change, contact Chemistry for coolant samples.
APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 18
- EVENT 4 INCREASING POWER FOLLOWING RUNBACK SIGNAL RESET The crewwill take action to restore reactor power to the pre-runback level.
Malfunctions required:
None Objectives:
SCO Directs RO to raise reactor power to 90% by raising Recirculation Flow on "An Loop RO Raises reactor power per 20P-02.0, section 5.3, by raising "An Recirculation Pump Speed Success Path:
Reactor power is raised to approximately the pre-runback level.
Simulator Operator Activities:
WHEN asked, as the Nuclear Engineer, report that power may be raised without ramp limitations, to 90% to clear the loop mismatch, using Reactor Recirculation flow. Then, predicts will have to be run prior to pulling rods. IF the unaffected loop was lowered to clear the mismatch request raising the lower speed pump to match speeds then balance flow adjustments to 90%, then predicts will have to be run prior to pulling rods.
- 2007 NRC Examination Scenario #1 19
- Required Operator Actions Normal Operating Procedures - 20P-02
- EVALUATOR NOTE: Alternate Power Verification is required at 10% power increments during power ascension and takes approximately 10 minutes to complete. If a change to the Gain Adjustment Factor (GAF) is required following Alternate Power Verification, an additional 15 minutes should be allowed.
At the evaluator's discretion, prompt may be given stating that Alternate Power Verifications are to be completed by other members of the operating crew and are satisfactory.
- Contacts Load dispatcher regarding power increase
- When directed, raises reactor power to approximately 90% using Reactor Recirculation Flow per 20P-02.0 .
- 2007 NRC Examination Scenario #1 20
- EVENT 4 INCREASING POWER FOLLOWING RUNBACK SIGNAL RESET APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 21
- EVENT 5 INSTRUMENT LINE PENETRATION FAILS The crew will observe and report the parameter changes impacted by the instrument failure. The SCO will diagnose the failure and evaluate the impact to plant operation, including Technical Specification action statement(s).
Malfunctions required:
- Penetration X49A Level instrument B21-N026B will fail.
Objectives:
SCO - Diagnose the failure of the level instrument and evaluate the impact of the loss in TS (3.6.1.3 - Primary Containment Isolation Valves (PCIVs), 3.3.3.1 - Post Accident Monitoring (PAM) Instrumentation and 3.3.3.2 - Remote Shutdown Monitoring Instrumentation- 30 days).
Success Path:
SCO correctly evaluates the impact of the loss of the instrumentation, including the correct Technical Specification action statement.
Simulator Operator Activities:
- WHEN directed by the lead examiner, activate TRIGGER 3 (Instrument line break, B21-N026B fails).
- IF directed to investigate penetration wait 3 minutes and report there is some evidence of a leak but you cannot determine the source.
- 2007 NRC Examination Scenario #1 22
- Required Operator Actions:
seo
- Evaluate the plant impact and Technical Specification requirements for the instruments affected Tech Spec 3.6.1.3.C One or more penetration flowpaths with one PCIV Primary Containment Isolation Valve) inoperable C.1 Isolate the affected flowpath by using at least one closed automatic valve, manual valve, or blind flange (12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> for Excess Flow Check Valve)
AND C.2 Verify isolated (every 31 days)
Tech Spec 3.3.3.1 Post Accident Monitoring (PAM)
A.1 One or more Functions with one required channel inoperable (restore to Operable in 30 days)
Tech Spec 3.3.3.2 A.1 One or more required Functions inoperable (restore to Operable in 30 days)
- Refers to Annunciator Response UA-24 1-3 "Pen X 49A ELEV 86'-0" AZIMUTH 225 degrees.
- 2007 NRC Examination Scenario #1 23
- EVENT 5 INSTRUMENT LINE PENETRATION FAILS APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 24
- EVENT 6 AOG FAILS TO ISOLATE ON HIGH H2 SIGNAL The crew will respond to the AOG failure to isolate.
Malfunctions required:
The H2 instrument 2-0G-AIT-4324 Stream1 will fail upscale.
Objectives:
SCO Directs BOP operator to respond to annunciators Evaluates ODCM for AOG bypassed BOP Reponds to annunciators Take manual actions to isolate AOG Success Path:
AOG isolated Simulator Operator Activities:
- WHEN directed by lead examiner activate TRIGGER 12 (AOG failure to isolate on high-high H2 signal).
- WHEN contacted as TBAO, to investigate status of the H2 detectors acknowledge and respond in 3 minutes that H2 instrument 2-0G-AIT-4324 Stream1 has failed upscale.
- WHEN contacted as I&C to investigate failure, acknowledge only.
- 2007 NRC Examination Scenario #1 25
- EVENT 6 AOG FAILS TO ISOLATE ON HIGH H2 SIGNAL Required Operator Actions:
seo
- Directs BOP to respond to annunciators 2-UA 45 2-1, DISCHARGE H2 CONC HI-HI 2-UA 45 2-2, DISCHARGE H2 CONC HI 2-UA 485-4, AOG SYSTEM BYPASS
- Evaluates impact of AOG bypassing at power:
ODCM 7.3.10 Gaseous Radwaste Treatment System A.1 Place system in service when Main Condenser Air Ejector System is in operation (7 Days)
- Directs isolating AOG in accordance with the APP
- Contact I&C to investigate 2-0G-AIT-4324 Stream 1 failure and AOG failure to isolate.
- Responds to annunciators:
2-UA 45 2-1, DISCHARGE H2 CONC HI-HI 2-UA 45 2-2, DISCHARGE H2 CONC HI 2-UA 485-4, AOG SYSTEM BYPASS
- Isolates AOG by manipulating valve control switches as required in
'annunciator response procedures.(XCV-148, 147, 143, 142, and 141 closed)
EXAMINER NOTE: Valves will not re-position until ALL FIVE (5) switches are in the CLOSED position .
- 2007 NRC Examination Scenario #1 26
- EVENT 6 AOG FAILS TO ISOLATE ON HIGH H2 SIGNAL APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 27
- EVENT? REACTOR SCRAM, LOSS OF OFF-SITE POWER, DG #3 FAILURE The crew will respond to a loss of off-site power resulting in a reactor scram and a corresponding failure of Emergency Diesel Generator #3 due to an electrical fault on Bus E3.
Malfunctions required:
- Off-site power will be lost due to a grid disturbance resulting in a reactor scram. Immediately following the starting and synchronization of #3 Emergency Diesel Generator, an electrical fault will develop on Emergency Bus E3, resulting in a trip of #3 Diesel Generator and unavailability of the Emergency Bus E3.
Objectives:
SCO - Executes the Emergency Operating Procedures: Enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure (if Rx Press is >1060 psig or Rx Level cannot be restored and maintained >170")
Directs the RO to control reactor and containment parameters o Control pressure using SRVs with a pressure band of 800-1000 psig o Control Level using HPCI/RCIC with a band of 170" to 200" Directs BOP to enter and execute AOP-36.1 in response to the loss of off-site power and Diesel Generator failure Contacts System Load Dispatcher to determine Distribution Grid status RO Responds to the reactor scram and takes actions to control level and pressure in the established control bands using HPCI, RCIC, and SRVs
- 2007 NRC Examination Scenario #1 28
BOP Report Electric Plant status o Loss of off-site power o DG #4 loaded to Bus E4 o DG #3 tripped due to overcurrent trip on bus o Performs AOP-36.1 actions based on transient response priorities, including but not limited to the following:
Places PCB auto-reclosers to OFF Transfers 120v panels Pursues Service Air cross-tie Ensures 2B Nuclear Service Water Pump is running, starts 2B and 2C Conventional Pumps Starts Control Room and Battery Room HVAC Direct Transfer of RBCCW Cooling to Conventional Service Water Start 2B CRD Pump Direct RPS to be restarted Success Path:
SCO successfully enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure and directs activities relating to reactor vessel control (RPV pressure and level) and directs activities relating to the loss of electrical power. RO takes actions to control reactor level and pressure (HPCI, RCIC, SRV operation). BOP enters OAOP-36.1 and takes actions, as directed to address the loss of electrical power.
- 2007 NRC Examination Scenario #1 29
- WHEN directed by lead examiner, activate TRIGGER 4 (Loss of offsite power, DG#3 failure)
- IF contacted as Load Dispatcher, report that there has been storm damage to the Transmission Grid and that there is, currently, not a projected time for return to service.
- IF asked as Unit One (1) for permission to cross-tie air, grant permission.
- WHEN it is requested to cross-tie air, report Unit One (1) crosstie valve 1-SA-PV-5071 is open.
- IF asked to transfer RCC to CSW, wait 4 minutes and activate TRIGGER 8.
- IF asked to restart RPS, wait 3 minutes and activate TRIGGER 9.
- IF requested to transfer 2AB, 2AB-RX and 32AB to alternate, wait 2 minutes and activate TRIGGER 7.
- IF asked by I&C to investigate DG #3 failure, wait 3 minutes and report the EDG trip is due to an electrical lockout and is being investigated .
- 2007 NRC Examination Scenario #1 30
- Executes the Emergency Operating Procedures: Enters 2EOP-01-RSP, Reactor Scram Procedure and, subsequently, enters 2EOP-01-RVCP, Reactor Vessel Control Procedure (if Rx Press is >1060 psig or Rx Level cannot be restored and maintained> 170")
- Directs the RO to control reactor parameters o Control pressure using SRVs with a pressure band of 800-1000 psig (actions on SCRAM Hard Card) o Control Level using HPCI/RCIC with a band of 170" to 200"
- Directs BOP to enter and execute AOP-36.1 in response to the loss of off-site power and Diesel Generator failure o Directs E-Bus cross-tie at the 480V Buses (E7 to E8)
- Contact System Load Dispatcher to determine Distribution Grid status
- Enters and executes OEOP-02-PCCP when temperature exceeds 95°F in the Suppression Pool and directs RO to maximize Suppression Pool Cooling using RHR.
o All Rods In (Rod Worth Minimizer) o Trips Main Turbine o Places Reactor Mode Switch to Shutdown when total steam flow is
<3Mlbm/hr) meters on RTGB with "red" lines) o Verifies Heater Drain Pumps Tripped Inserts SRMs/IRMs (selects detectors and energizes circuit selects drive o
pushbutton on RTGB left of rod select matrix) 2007 NRC Examination Scenario #1 31
RO (cont.)
- Verifies SCRAM Hard Card Actions
- Controls Reactor pressure using SRVs by placing various SRV control switches to "Open" and, subsequently, places switches back to Close/Auto to control Reactor pressure 800 psig to 1000 psig.
NOTE: If HPCI injection valve, 2-E41-F006, failure is found early level will be recovered and entry into RVCP will be later in scenario
- If not automatically started, Starts HPCI/RCIC using the Hard Card to provide coolant injections for level control:
o RCIC
- Open E51-F046
- Start Barometric Vacuum Pump
- Open E51-F045
- Open E51-F013
- Open E41-F059
- Start Vacuum Pump
- Open E41-F001
- Start Aux Oil Pump
- Open E41-F006 (auto open on valve is failed, but valve will open when control switch is operated)
- Adjust Flow Controller to desired injection rate.
When directed, places "A" and "B" loops of RHR in Suppression Pool Cooling per the Hard Card .
- 2007 NRC Examination Scenario #1 32
RO (cont.)
NOTE: Depending on availability, the BOP operator may perform the actions to place RHR in Suppression Pool Cooling.
- Service Water o Opens SW-V105 ("B" loop) and SW-V101 ("A" loop) o Starts RHRSW Booster Pump (places control switch to start and throttles Open E11-F068 AlB)
- RHR o If E11-F015A(B) is Open, closes E11-F017A(B) o Starts Loop A(B) RHR pump using control switch o Opens E11-F028A(B) o Throttles Open E11-F024A(B)
- BOP o Throttles Closed E11-F048A(B)
Recognizes and Reports Electric Plant status
-Loss of off-site power
-DG #4 loaded to Bus E4
-DG #3 tripped due to electrical lockout on the bus
- Executes applicable steps of OAOP-36.1 in response to the loss of off-site power and failure of the #3 Emergency Diesel Generator and Emergency Bus E3. These actions include, but are not limited to the following:
o Places PCB auto-reclosers to OFF o Directs field Operator to transfer 120v panel (2AB, 2AB-RX, and 32AB) o Directs field Operator to transfer RBCCW Cooling to Conventional Service Water 2007 NRC Examination Scenario #1 33
BOP (cont.)
o Places RBCCW Pump control switches to OFF o Places Condensate Pump control switches to manual o Directs field Operator to cross-tie 480V Emergency Busses (E7 to E8)
- On a priority bases, executes any additional steps of OAOP-36.1 in response to the transient which might be applicable:
o Restart of RPS MG Set o Pursues Service Air cross-tie o Ensures 2B Nuclear Service Water Pump is running, starts 2B and 2C Conventional Pumps o Starts Control Room and Battery Room HVAC o Starts 2B CRD Pump
- 2007 NRC Examination Scenario #1 34
- 2007 NRC Examination Scenario #1 35
- EVENT 8 HPCIINJECTION VALVE FAILS TO OPEN The crew will respond to a failure of the HPCI injection valve to fail to automatically open on a valid initiation signal.
Malfunctions required:
- The 2-E41-F006, HPCI Injection Valve, will fail to automatically open on a valid initiation signal Objectives:
SCO/RO Identifies that the HPCI Injection Valve has failed to open on a valid initiation signal RO Opens the HPCI Injection Valve by taking the control switch to the "OPEN" position and commences injection with HPCI Success Path:
HPCI injection is established at rated flow by operator action to open the HPCI injection valve.
- Simulator Operator Activities:
None Required Operator Actions:
SRO/RO
- Identifies the HPCI Injection Valve, 2-E41-F006, has failed to open on a valid initiation signal
- Opens the 2-E41-F006 by taking the control switch to the "OPEN" position and establishes injection flow to the reactor from HPCI .
- 2007 NRC Examination Scenario #1 36
- EVENT 8 HPCIINJECTION VALVE FAILS TO OPEN APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 37
- EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION The crew will respond to a steam leak in the drywell in conjunction with a failure of the ability to spray the containment, subsequently leading to a requirement to Emergency Depressurize the reactor due to high drywell temperature.
Malfunctions required:
- A steam leak will occur in the drywell, resulting in elevated drywell temperatures
- A failure will be inserted, preventing the opening of the "B" Loop Drywell Spray injection valve
- Cross tie of E7 to E8 will not function Objectives:
SCO Recognize conditions of the steam leak in the drywell (elevated temperatures and pressures) and provide direction to the RO and BOP.
Direct execution of applicable steps of OEOP-02-PCCP (Primary Containment Control Procedure).
- CRITICAL TASK*** When drywell temperature cannot be restored and maintained <300°F, direct Emergency Depressurization of the reactor Refer to Caution 1 and determine that the Reactor Saturation Graph will enter the "Unsafe" region during the depressurization RO/BOP Continue to maintain control of Reactor Water Level and Pressure, as directed by the SCO Must manually trip RCIC when High level trip setpoint is reached (206")
Place "B" Loop of RHR in Suppression Pool Cooling when directed Attempt to place "B" Loop in Suppression Chamber (SEP-03) and Drywell Sprays (SEP-02) when directed Identify and report failure of "B" Loop Drywell Spray valve to open and take actions to attempt to open the valve When directed, Emergency Depressurize the reactor (high drywell temperature)
Control injection from Low Pressure systems to maintain reactor water level during depressurization.
Success Path:
When 300°F is exceeded in the drywell, the reactor is Emergency Depressurized and level is restored/maintained in the normal band (170" to 200")
- 2007 NRC Examination Scenario #1 38
- EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION Simulator Operator Activities:
- WHEN directed by the lead examiner, activate TRIGGER 5 (Steam leak in drywell)
- IF asked, report that the breaker for the 2-E11-F016B appears to have normal indication..
- IF asked, indicate reset of the thermal overload for 2-E11-F016B appears to have had no impact.
- IF asked to manually open the 2-E11-F016B, report that the 2-E11-F016B is mechanically bound and will not open.
- WHEN requested to lock-out drywell coolers, activate TRIGGER 6.
- IF requested to support E7 to E8 cross-tie, acknowledge request. AFTER 5 minutes report racking mechanism on E7 cross-tie breaker has failed, maintenance has been notified for help.
- Required Operator Action SRO
- Recognize primary containment conditions (temperature rise and pressure rise) indicate a steam leak in the drywell.
- Direct execution of applicable steps of OEOP-02-PCCP (Primary Containment Control Procedure).
o Prior to Suppression Chamber Pressure exceeding 11.5 psig
- Directs RO/BOP to perform Suppression Pool Spray per SEP-03 o When Suppression Chamber exceeds 11.5 psig,
- Directs RO/BOP to perform Drywell Sprays per SEP-02 o Monitors Pressure Suppression Pressure to maintain in the SAFE region of the graph (utilizes ERFIS) o When Drywell air temperature exceeds 150°F
- Directs RO/BOP to start all available drywell coolers (SEP-1 0 allowed) o Prior to Drywell air temperature exceeding 300°F
- Directs RO/BOP to initiate Drywell Spray per SEP-02
- 2007 NRC Examination Scenario #1 39
- EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION Required Operator Action (continued)
SRO (cont.)
- **** CRITICAL TASK**** When drywell temperature cannot be restored and maintained <300°F, direct Emergency Depressurization of the reactor
- Refer to Caution 1 and determine that the Reactor Saturation Graph will enter the "Unsafe" region during the depressurization
- Other Primary Containment Control actions may be directed, but are non-consequential to the event.
RO/BOP
- Continue to maintain control of Reactor Water Level and Pressure, as directed by the SCO.
- When directed place "B" Loop of RHR in Suppression Pool Cooling o Service Water Opens SW-V105 ("B" loop) and SW-V101 ("A" loop)
Starts RHRSW Booster Pump (places control switch to start and throttles Open E11-F068 AlB) o RHR
- If E11-F015B is Open, closes E11-F0178
- Starts Loop B RHR pump using control switch
- Opens E11-F028B
- Throttles Open E11-F0248
- Throttles Closed E11-F048B
- 2007 NRC Examination Scenario #1 40
- EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION Required Operator Action (continued)
RO/BOP (cont.)
- When directed place RHR in Suppression Chamber Sprays (SEP-03) o Places 2/3 Core Height Override Position to ON o Place Containment Spray Valve Control Switch to Manual o If E11-F015B is Open and RHR injection is not necessary, close E11-F017B o Start/Ensure a loop RHR pump is running o Open E11-F028B o Open E11-F027B o Ensure Loop is aligned to one of the following: LPCI, Suppression Pool Cooling, or Drywell Spray.
- When directed to spray the Drywell per SEP-02 o Ensure Recirc Pumps are tripped o Ensure Drywell Coolers not running o Close E11-F024B o Verify in Safe region of Drywell Spray Initiation Graph o Ensure "B" loop RHR pump running o Open E11-F021 B o Open E11-F016B
- Notifies SRO when it is recognized that the E11-F016B will not open
- **** CRITICAL TASK**** When directed, Emergency Depressurize the Reactor by placing 7 ADS valve control switches to Open.
- As Reactor pressure lowers, controls injection systems (RHR, Core Spray) to prevent overfilling by throttling loop injection valves and/or securing pumps as necessary.
o RHR E11-F017A(B) o Core Spray E21-F005B NOTE: Indicated level will exceed 200 inches due to Emergency
- Depressurization swell.
2007 NRC Examination Scenario #1 41
- EVENT 9/10 STEAM LEAK IN DRYWELL REQUIRING EMERGENCY DEPRESSURIZATION APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 42
- EVENT 11 LEVEL INSTRUMENT FAILURE DUE TO REFERENCE LEG FLASHING
- REACTOR FLOODING REQUIRED The crew will respond to indications of Reactor Pressure Vessel Level reference leg flashing, resulting in inability to determine reactor water level (entry condition for Reactor Flooding Procedure).
Objectives:
SCO As the reactor depressurizes, recognize indications of reference leg flashing resulting in no level instrumentation being available
- CRITICAL TASK**** Enter and execute EOP-01-RxFP,Reactor Flooding Procedure, and establish Minimum Reactor Flooding Pressure.
RO/SOP Implement directions given by SCO to establish required Reactor Flooding Conditions to ensure adequate core cooling Success Path:
Reactor Pressure Vessel Injection has been established resulting in at least 5 safety relief valves (SRVs) being open with at least 50 psid (but as low as possible) between the Reactor and Suppression Chamber Pressure.
Simulator Operator Activities:
- None
- 2007 NRC Examination Scenario #1 43
- EVENT 11 LEVEL INSTRUMENT FAILURE DUE TO REFERENCE LEG FLASHING
- REACTOR FLOODING REQUIRED Required Operator Actions:
EOP Action - Entry into and Execution of Reactor Flooding Procedure SCO ****CRITICAL TASK****
- As the reactor depressurizes, correctly evaluate indications to determine Level Instrument Reference Leg Flashing is occurring
- Enter and execute EOP-01-RxFP, Reactor Flooding Procedure to ensure adequate core cooling
- Determines 5 or more SRVs can be opened o Directs RO/80P to close 821 F022A-D (inbd MSIV's), 821-F028A-D (otbd MSIVs), E51-F0078 (RCIC), 821-F016/F019 (Drain bypasses) o Directs RO/80P to inject with RHR, Core Spray, CRD, and Alternate Cooling Injection Systems at maximum irrespective of NPSHNortex limits NOTE: If 5 or more SRVs can be Opened is answered NO, same steps, as above, except steam valve isolations are not directed.
o When Reactor pressure is at least 50 psig above Suppression Chamber Pressure, direct that injection be controlled to maintain at least 5 SRVs open.
RO/BOP
- Observe and report indications of Reactor Vessel Level indication reference leg flashing
- When directed, Close 821-F022A-D, 821-F028A-D, E51-F008, 821-F016/F019 by placing their control switches to Closed.
- When directed starts some/all of the following systems in any order to establish 5 SRVs open and 50 psid between Reactor Vessel and Suppression Chamber.
o "8" Core Spray Pump; ensures E21-F0048/F0058 opens o "C" RHR Pump; ensures E11-F015A1F017A opens o "8" and "D" RHR pumps; ensures E11-F0158/F0178 opens o If required, (ECCS pumps do not result in SRV opening) then starts LEP-01 systems (SLC injection) o Controls injection by throttling Core Spray Injection Valve (E21-F0058/RHR Injection Valves E11-F017A18) to maintain 5 SRVs open.
2007 NRC Examination Scenario #1 44
- EVENT 11 LEVEL INSTRUMENT FAILURE DUE TO REFERENCE LEG FLASHING
- REACTOR FLOODING REQUIRED APPLICANT'S ACTIONS OR BEHAVIOR:
- 2007 NRC Examination Scenario #1 45
- Simulator Operator Activities:
WHEN directed by the lead examiner, place the simulator in FREEZE.
CAUTION DO NOT RESET THE SIMULATOR PRIOR TO RECEIPT OF CONCURRENCE TO DO SO FROM THE LEAD EXAMINER
- 2007 NRC Examination Scenario #1 46
- RPV Level Transmitters (FIGURE 01.2-4 from SO-01 )
CR~50-to.50. 0 50-'0550-P60W ~sop
~---t----j----I--:-I :
I
__ I Ot0210-U CR P604 1 P601 A I I
I I
I I
I I
I I
I
- CR P6D3 I
I I
,~-----------------------------
C32~15O-210~
R606 B
213 CORE HEIGHT.
~
R615 CR J
P601 5977 I
INTERLOCK I I I
L----------IN~I+----------- ...
CR* CONTROL ROOM 2/3 CORE HEIGHT. .
INTERLOCK - - - :~@-l LI RSi0
-150-to+ 150'"
- 2007 NRC Examination Scenario #1 47
- ATTACHMENT 1
- Title - 2007 NRC Scenario 1
- Path - E:\NRC Simulator Dynamic Masters\NRC Scenario SCN files\2007 NRC Scenario 1.scn
- Saved on 06-29-2007 at 16:03:28 mfi:ES028F,True,00:00:00,00:00:00, 0 mfi:NB014F,True,00:00:00,00:00:00,3 mfi:EE009F,True,00:00:00,00:00:00, 4 mfi:DG026F,True,00:00:00,00:00:00, 0 mfi:NB006F, 4,00:05:00,00:00:00,00:00:00, 5,A mfi:RC026F,True,00:00:00,00:00:05, 2 mfi:NB025F,True,00:00:00,00:00:00, 0 mfi:CN019F,True,00:00:00,00:00:00, 0 mfi:CN011 F,True,OO:OO:OO,OO:OO:OO, 12 rfi:EP_IACS993P,STOP,00:03:00, 6 rfi:EP_IACS994P,STOP,00:03:00, 6 rfi:SW_IAVSW193,CLOSE,00:04:00,8 rfi:SW_VHSW146L,OPEN,00:04:00, 8 rfi:RP_IARPSB,RESET,00:03:00, 9 rfi:RP_IAEPAMGB,SET,00:03:00, 9 rfi:ED_ZIEDH08,ALT,00:02:00, 1 rfi:ED_ZIEDH11,ALT,00:02:00, 7 rfi:ED_ZIEDHXO,ALT,00:02:00, 7 tri:10, K4522NWD tri:11, K2711 PS8 trc:10, batf:\nrc scenario s-1.bat trc:11, did:k2712a dii:K1 J36A,AUTO,OFF,00:00:00,00:00:00, 0 dii:K1 J36A,CLOSE,ON,00:00:00,00:00:00, 0 dii:K1 J36A,OPEN,OFF,00:00:00,00:00:00, 0 dii:K4522A,ON,OFF,00:00:00,00:00:00, 1 dii:K4521 A,AUTO,OFF,OO:OO:OO,OO:OO:OO, 1 doi:Q4522LG4,ON/OFF,OFF,00:00:00,00:00:00, 1 dii:K2712A,NORM,ON,00:00:00,00:00:00, ° doi:Q4522RR4,ON/OFF,ON,00:00:00,00:00:00, 1 dii:K2712A,RESET,OFF,00:00:00,00:00:00, 0 dii:K2712A,TRIP,OFF,00:00:00,00:00:00, 0
- TITLE - NRC Scenario S-1
- Path - E:\NRC Scenario S-1.bat
- Saved on 6-29-2007 DOD:Q4522RR4 DOD:Q4522LG4 2007 NRC Examination Scenario #1 48
- WordPerfect Document Compare Summary Original document: P:\SES_CDP\MY_Templates\OPM SUMMARIES\OPM Summary Template_CRO_Final_rev2. wpd Revised document: @PFDesktop\:MyComputer\P:\SES_CDP\MY_Templates\OPM SUMMARIES\OPM Summary Template_CRO_Final_rev3.wpd Deletions are shown with the following attributes and color:
Strikeout, Blue RGB(O,O,255).
Deleted text is shown as full text.
Insertions are shown with the following attributes and color:
Double Underline, Redline, Red RGB(255,O,O).
The document was marked with 57 Deletions, 61 Insertions, °Moves.