ML17277A523: Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(Created page by program invented by StriderTol)
 
(3 intermediate revisions by the same user not shown)
Line 3: Line 3:
| issue date = 03/16/1983
| issue date = 03/16/1983
| title = Rev 1 to Reverification Instruction QVI-09, Special Structural Steel Reinsp Criteria.
| title = Rev 1 to Reverification Instruction QVI-09, Special Structural Steel Reinsp Criteria.
| author name = CRISP H A
| author name = Crisp H
| author affiliation = WASHINGTON PUBLIC POWER SUPPLY SYSTEM
| author affiliation = WASHINGTON PUBLIC POWER SUPPLY SYSTEM
| addressee name =  
| addressee name =  
Line 17: Line 17:


=Text=
=Text=
{{#Wiki_filter:WAS)lINUTON PUBUC POWER SUPPLY SYSTEM NO.AEV.NO%VI-G9 Pa'ih&V TITLE REVERIFlGATIOH.iNSTRUCTlON SPECIAL'TRUCTURAL STFEL'RE N EFFECTIVE OATE 3/16 83 QUALITY AFFECTING Q YES NO 1.0 PURPOSE/SCOPE This instruction describes the criteria to be used to determine the sign-ificance of discrepancies discovered during the reverification inspec-tions of structural steel welding at WNP-2.2.0 DEFINITIONS o Visual Examination Acceptance Criteria-A set of"fitness-for-use" inspectim criteria for determining whether welded structural com-ponents are adequate for their intended purpose.Such criteria shall be approved b'y the'Architect Engineer in accordance with Paragraphs:
{{#Wiki_filter:NO.
3.7.4 and 5.7.5 of AWS Dl.l,,the Structural Welding Code, 1972 Edition.o, Structural Steel-For the purpose of this instruction, structural steel includes pipe supports, hangers, ductwork, stiffeners, cable trays, unistrut, brackets and similar components, as well as struc'-tural shapes and plates and miscellaneous steel.3.0 PROCEDURE Res onsibilit Reverification
                                                                                        %VI-G9 WAS)lINUTON PUBUC POWER SUPPLY SYSTEM         AEV. NO Pa'ih&V                                                               EFFECTIVE OATE 3/16 83 REVERIFlGATIOH .iNSTRUCTlON               QUALITYAFFECTING Q YES      NO TITLE SPECIAL'TRUCTURAL STFEL 'RE     N 1.0     PURPOSE/SCOPE This instruction describes the criteria to be used to determine the sign-ificance of discrepancies discovered during the reverification inspec-tions of structural steel welding at WNP-2.
.Inspection Team.2 Action Inspects the welded structures for confor-mance with the requirements of the draw-'ngs, specifications, codes and standards, except as modified herein.The visual Ex-'mination Acceptance Criteria identified'n Attachment 2, shall be used in lieu of the acceptance criteria specified in AWS Dl.l, The justification for these criteria is included as Attachment 1 to this instruc-tion.Records the results of the inspections in accordance with QVI-08.8304080iqi 830323 PDR ADOCK 05000397 8 ,.-PDR APPAOV 0'WP.100 SUPENSEOES ISSUE 0 PACE OF 1 1~  
: 2. 0     DEFINITIONS o     Visual Examination Acceptance Criteria - A set of "fitness-for-use" inspectim criteria for determining whether welded structural com-ponents are adequate for their intended purpose. Such criteria shall be approved b'y the 'Architect Engineer in accordance with Paragraphs: 3.7.4 and 5.7.5 of AWS Dl.l,,the Structural Welding Code, 1972   Edition.
~QV.I-09 Rev.1
o,   Structural Steel For the purpose of this instruction, structural steel includes pipe supports, hangers, ductwork, stiffeners, cable trays, unistrut, brackets and similar components, as well as struc'-
tural shapes and plates and miscellaneous steel.
: 3. 0     PROCEDURE Res onsibilit                                         Action Reverification                             Inspects the welded structures for confor-
  . Inspection      Team                      mance with the requirements of the draw-specifications, codes and standards,                'ngs, except as modified herein. The visual Acceptance Criteria identified'n Ex-'mination Attachment 2, shall be used in lieu of the acceptance criteria specified in AWS Dl.l, The justification for these criteria is included as Attachment 1 to this instruc-tion.
                                          .2  Records the results of the inspections       in accordance with QVI-08.
8304080iqi 830323 PDR ADOCK         05000397 8   ,   .               PDR SUPENSEOES ISSUE APPAOV 0 0         PACE   1  OF 1~
      'WP.100


==4.0 REFERENCES==
~
QV.I-09 Rev. 1
: 4. 0 REFERENCES 4.1  Quality Verification Program QV'-01 4.2  American Welding Society  Structural Welding  Code Dl.l, 1972 Edition 4.3  Reverification Inspection  Team  Concept, QVI-08
: 5. 0  ATTACHMENTS 5.1  3ustification For WNP-2  Visual Examination Acceptance Criteria 5.2  WNP-2  Visual Examination Acceptance Criteria For Reverification In-spection Of Welded Structures Page 2  of 12


===4.1 Quality===
t        QVI-09 Rev. 1 JUSTIFICATION FOR WNP-2 VISUAL EXlWINATION ACCEPTANCE CRITERIA 1,0 JUSTIFICATION    FOR VISUAL ACCEPTANCE      CRITERIA The use  of the  AWS  Dl.l code for  the WNP-2 Plant was specified by the Engineer as the applicable structural welding code on behalf of the Owner, and, as such AWS D1.1-72 is identified in the FSAR. Unlike the ASME code, the use of the code is not a mandatory State or NRC regulatory requirement. The Engineer has the authority under the AWS code to modify selected provisions of the 4WS code to suit a particular application.
Verification Program QV'-01 4.2 American Welding Society Structural Welding Code Dl.l, 1972 Edition 4.3 Reverification Inspection Team Concept, QVI-08 5.0 ATTACHMENTS
It is  important to understand that the        AWS Dl.l code is the applicable structural  code  for boL'h completed work    (first-line inspection) and on-going construction. Site      construction and inspection procedures require that welds be made to the      applicable AWS crit ria and that. the first-line inspection be performed in accordance with the AWS D1.1 code. In cases where deviations are evaluated by the Engineer to be non-significant in terms of the ability of the component to perform its designed          function,'he Engineer has the authority to disposition the deviation "accept-as-is" as appropriate, or compensate for the deviation by additional evaluation or have construction performed to an approved, revised design.
During the  initial QVP    reinspection of completed .work, a number of minor deviations with respect to sow AWS criteria were encountered which were evaluated by the Engineer as acceptable in certain categories of applica-tion. Since the specific deviations had been evaluated by the Engineer to be acceptable for these categories of application, the processing of additional deviations of the sam type in the same categories served no purpose.
Thus, a generic    disposition  was  developed by the Engineer    for  acceptance
    .of specified    deviations, from the    AWS  01.1, l972 code in selected applica-tions. This generic disposition has taken the form of a revised inspec-tion criteria for use by the QVP for reinspection of completed work.
These criteria are embodied within the reverification inspection require-ments in Attachment 2 of QVI-09.
Attachment    1 (Page  1  of  1)
Page 3        of 12


===5.1 3ustification===
QVI-09 Rev. 1 HNP-2 PROJECT VISUAL EXAMINATION ACCEPTANCE CRITERIA FOR REVERIFICATION INSPECTION OF" l(ELDED STRUCTURES
For WNP-2 Visual Examination Acceptance Criteria 5.2 WNP-2 Visual Examination Acceptance Criteria For Reverification In-spection Of Welded Structures Page 2 of 12 t QVI-09 Rev.1 JUSTIFICATION FOR WNP-2 VISUAL EXlWINATION ACCEPTANCE CRITERIA 1,0 JUSTIFICATION FOR VISUAL ACCEPTANCE CRITERIA The use of the AWS Dl.l code for the WNP-2 Plant was specified by the Engineer as the applicable structural welding code on behalf of the Owner, and, as such AWS D1.1-72 is identified in the FSAR.Unlike the ASME code, the use of the code is not a mandatory State or NRC regulatory requirement.
(.
The Engineer has the authority under the AWS code to modify selected provisions of the 4WS code to suit a particular application.
Approved:
It is important to understand that the AWS Dl.l code is the applicable structural code for boL'h completed work (first-line inspection) and on-going construction.
Burns 8 Roe, Inc.
Site construction and inspection procedures require that welds be made to the applicable AWS crit ria and that.the first-line inspection be performed in accordance with the AWS D1.1 code.In cases where deviations are evaluated by the Engineer to be non-significant in terms of the ability of the component to perform its designed function,'he Engineer has the authority to disposition the deviation"accept-as-is" as appropriate, or compensate for the deviation by additional evaluation or have construction performed to an approved, revised design.During the initial QVP reinspection of completed.work, a number of minor deviations with respect to sow AWS criteria were encountered which were evaluated by the Engineer as acceptable in certain categories of applica-tion.Since the specific deviations had been evaluated by the Engineer to be acceptable for these categories of application, the processing of additional deviations of the sam type in the same categories served no purpose.Thus, a generic disposition was developed by the Engineer for acceptance.of specified deviations, from the AWS 01.1, l972 code in selected applica-tions.This generic disposition has taken the form of a revised inspec-tion criteria for use by the QVP for reinspection of completed work.These criteria are embodied within the reverification inspection require-ments in Attachment 2 of QVI-09.Attachment 1 (Page 1 of 1)Page 3 of 12 QVI-09 Rev.1 HNP-2 PROJECT VISUAL EXAMINATION ACCEPTANCE CRITERIA FOR REVERIFICATION INSPECTION OF" l(ELDED STRUCTURES
Date:
(.Approved: Date: Burns 8 Roe, Inc.j'-/7-P g Attachment 2 (Page 1 of 9)Page 4 of 12 QVI-O9 Rev.l 1.0 SCOPE This document provides visual examination acceptance criteria for reveri-fication inspection of structural steel and miscellaneous metal welding performed in accordance with AWS Dl.l, the Structural Welding Code.These criteria reflect requirements consistent with the engineering approval specified, in AWS Dl.l for evaluation of structural welding.This document also includes acceptance standards for light gauge HVAC ductwork, and other systems which are not specifically covered by AWS D.1.1.1.1 These, criteria shall be used by Construction Quality Control for pe forming reverification inspection by including it on the QCIR as an applicable inspection reference criteria document to evaluate deviations to AWS Dl.l.2.0 CODES AND STANDARDS The criteria in this document provide the basis for visual examination of AWS Dl.l welding.The required engineering approval, as specified in Paragraphs 3.7.4 and 3.7.5 of AWS Dl.l has been provided by the Architect Engineer.Authorization for this is given in Paragraph l.l of AWS Dl.l.3.0 BASIS FOR EVALUATION The applicable weld categories will be entered on the QCIR as a part of the inspection reference criteria based upon the definitions described below.3.l Category A Welds gust be in accordanc with the visual acceptance criteria of the specified section of AWS D1.1.This category applies to elements of fans, cranes, rotating equipment, and other machinery subject to frequent stress reversals.
j'-/7- P g Attachment   2 (Page 1 of 9)
Have, an acceptance level modified to meet the required service con-ditions.This category applies to members of the building frame that carry princioal design loads, radial beams, sacrificial shield wall, pipe whip rI'.straints, pipe supports, and similar principal load bearing structures.
Page 4   of 12
Attachment 2 (Page 2 of 9)Page 5 of 12 qvl-0~Rev.1 3.3 Cate or C Welds Are connections between Category 0 Steel and Miscellaneous Metal.3.4 Cate or D Welds.Are not part of the main building frame, but-rather provide support or framing for electrical, instrumentation, and HVAC systems, com-ponents and equipment.
Also included in the D Category are welds joining miscellaneous metal including, but not limited to, stair-ways, embedments, fan housings, doors, windows, hatches, frames,.ledger angles, gratings and their supports.Is an acceptance level established for relatively thin materials such as.HVAC ductwork, cable trays, and unistrut supports.4.0 ACCEPTANCE CRITERIA Acceptance shall be based on the weld joint meeting each criteria listed for the applicable category.Skewed joints will be evaluated in accordance with Cont~act Specifications and Project Engineering Directives.
~tld 4.1.1 Category A welds must comply with the visual examination requirements of the specified section of A'WS Dl.l.4.2 Cate or B Welds 4.2.1 Oversize Fillet Welds The weld shall meet or exceed the specified size require-ments.Either or both fillet weld legs may exceed design size.Welds may be longer than specified.
Continuous welds may be accepted in place of intermittent welds.Unequal leg fillet welds are acceptable, provided the smaller leg meets or exceeds minimum requirements.
4.2.2, Undersize Welds 4.2.2.1 The fillet leg dimension shall not under run the nominal fillet size by more than l/16 inch.For flange to web joints the undersize condition may not be within two flange thicknesses of the weld end.Attachment 2 (Page 3 of 9)Page 6 of 12 QV I-09 Rev.1 4.2.3 4.2.2.2 Groove welds may be underfilled by 5 percent or 1/32-inch, whichever is greater.Porosit and Sla 4.2.3.1 The weld may contain a maximum of 5 percent by surface area of unaligned porosity and/or slag.4.2.4 Profile 4.2.4.1 Convex-'ty height, roll over, and butt weld rein-forcement are acceptable.


====4.2.5 Craters====
QVI-O9 Rev. l 1.0  SCOPE This document provides visual examination acceptance criteria for reveri-fication inspection of structural steel and miscellaneous metal welding performed in accordance with AWS Dl.l, the Structural Welding Code.
4.2.5.1 The weld may have an underfilled crater, pro-vided the underfill depth does not exceed 1/16 inch, and the crater has a smooth contour blend-ing gradually with the adjacent weld and base metal without acute notches.4.2.6 Undercut 4.2'.6.1 Continuous undercut shall not be greater than: 1/32 inch for material 3/8 inch and less;1/16 inch f'r material over 3/8 inch thick.Intermittant undercut may be twice the value for continuous undercut for a maximum accumulated length of 10X of weld length.Localized und r-cut less than 3/8 inch in length may be accepted provided the depth does not exceed 3/32 inch for thickness 3/4 inch and less or 1/8 inch for thickness over 3/4 inches.4.2.7 Cracks 4.2.8 4.2.7.l Cracks are unacceptable.
These criteria reflect requirements consistent with the engineering approval specified, in AWS Dl.l for evaluation of structural welding.
Fus.rcn 4.2.8.1 Incomplete fusion between weld metal and base metal is unacceptable.
This document also includes acceptance standards for light gauge HVAC ductwork, and other systems which are not specifically covered by AWS D.1. 1.
Attachment 2 (Page 4 of 9)Page 7 of 12 QVI-09 Rev.1 4.2.9 Weld S atter 4.2,9.1 Weld spatter shall be acceptable.
1.1     These, criteria shall be used by Construction Quality Control for pe forming reverification inspection by including    it  on the QCIR as an applicable inspection reference criteria document to evaluate deviations to  AWS Dl.l.
4.2.10 Arc Strikes 4.2.10.1 Arc strikes are acceptable provided there are no cracks~4.2.11 Backin Fitu 4.2.11.1'The fitup of backing bars is not a basis for rejection.
2.0  CODES AND STANDARDS The  criteria in this document provide the basis for visual examination of AWS  Dl.l welding. The required engineering approval, as specified in Paragraphs 3.7.4 and 3.7.5 of AWS Dl.l has been provided by the Architect Engineer. Authorization for this is given in Paragraph l.l of AWS Dl.l.
~t.d 4.>.l The welds on the main frame member side shall rreet the requirements for Category B.4.3.2 The welds on the miscellaneous metal side shall meet the requirements for Category 0.4.4.1 Oversize Fillet Welds 4.4.1.1 The weld shall meet or exceed the specified size requirements, Either or both fillet weld legs may exceed design size.Welds may be longer than specified.
3.0  BASIS FOR EVALUATION The   applicable weld categories will be entered on the QCIR as a part of the inspection reference criteria based upon the definitions described below.
Continuous welds may be accepted'in place of intermittent welds.Unequal leg fillets are acceptable, provided the smaller leg meets or exceeds minimum requirements.
3.l    Category  A Welds gust  be in accordanc  with the visual acceptance criteria of the specified section of AWS D1.1. This category applies to elements of fans, cranes, rotating equipment, and other machinery subject to frequent stress reversals.
Have, an acceptance  level modified to meet  the required service con-ditions. This category applies to members  of the building frame that carry princioal design loads, radial    beams, sacrificial shield wall, pipe whip rI'.straints, pipe supports,  and similar principal load bearing structures.
Attachment 2 (Page 2 of 9)
Page 5 of   12


====4.4.2 Undersize====
qvl-0~
Welds 4.4.2.1 4.4.2.2 The fill't leg dimension shall not under run the nominal fillet size by more than 1/16 inch.Groove welds may be undersize by 5 percent or 1/16 inch, whichever is greater.Attachment 2 (rag~5 or 9)Page 8 of 12 QVL-09 Rev.1 4.4.3 Porosit and Sla 4.4.3.1 Porosity and slag are not a basis for rejection.
Rev. 1 3.3  Cate or    C  Welds Are connections between Category 0 Steel and Miscellaneous Metal.
3.4 Cate or    D  Welds  .
Are not part  of the main building frame, but- rather provide support or framing for electrical, instrumentation, and HVAC systems, com-ponents and equipment. Also included in the D Category are welds joining miscellaneous metal including, but not limited to, stair-ways, embedments,    fan housings, doors, windows, hatches,      frames,
          .ledger angles, gratings      and  their supports.
Is an acceptance level      established for relatively thin materials such as. HVAC ductwork,    cable trays, and unistrut supports.
: 4. 0 ACCEPTANCE CRITERIA Acceptance  shall be based on the weld joint meeting each criteria listed for the applicable category. Skewed joints will be evaluated in accordance with Cont~act Specifications and Project Engineering
          ~tld Directives.
4.1.1      Category A welds must comply with the visual examination requirements of the specified section of A'WS Dl.l.
4.2  Cate or  B  Welds 4.2.1       Oversize    Fillet  Welds The weld    shall meet or    exceed the specified size require-ments. Either or both    fillet weld legs may exceed design size. Welds may be longer than specified. Continuous welds may be accepted in place of intermittent welds.
Unequal leg    fillet  welds are acceptable, provided the smaller leg meets or exceeds minimum requirements.
4.2.2,    Undersize Welds 4.2.2.1      The   fillet leg dimension shall not under run   the nominal fillet size by more than l/16 inch.       For flange to web joints the undersize condition may not be within two flange thicknesses of the weld end.
Attachment 2 (Page 3  of 9)
Page 6  of 12


====4.4.4 Profile====
QV I-09 Rev. 1 4.2.2.2  Groove welds may be  underfilled by 5 percent  or 1/32-inch, whichever is greater.
4.4.4.1 Convexity height, roll'over, and butt weld rein-forcement-are acceptable.
4.2.3  Porosit  and Sla 4.2.3.1  The weld may  contain a maximum of 5 percent by surface area of unaligned porosity and/or slag.
4.4.5'usion 4.4.6 4.4.5.1 incomplete fusion between weld metal.and base metal is unacceptable.
4.2. 4 Profile 4.2.4.1   Convex-'ty height, roll over, and butt weld rein-forcement are acceptable.
Undercut 4.4.7 4.4.6.1 (Same as 4.2.6.1)Craters 4.4.7.1 Underfilled groove weld craters shall be accepted provided the depth of underfill is 1/16 inch or less.Lhderfilled single-pass fillet weld craters shall be accepted provided the crater length is less than 5 percent of the weld length.On multi-pass fillet welds a crater depth of 1/16 inch or less is acceptable.
4.2.5 Craters 4.2.5.1   The weld may have an  underfilled crater, pro-vided the underfill depth does not exceed 1/16 inch, and the crater has a smooth contour blend-ing gradually with the adjacent weld and base metal without acute notches.
4.4.8 4.4.9 Cracks 4.4.8.1 All cracks are unacceptable.
4.2.6 Undercut 4.2'.6.1 Continuous undercut shall not be greater than:
111 4.4.9.1 Misalignm"nt not.in excess of the thinner member thickness is ac eptable.4.4.10 Azc Strikes 4.4.10.1 Ar'c strikes are acceptable provided there are no cracks.Attachment 2 (Pag.6 of 9)Page 9 of 12  
1/32 inch for material 3/8 inch and less; 1/16 inch f'r  material over 3/8 inch thick.
Intermittant undercut may be twice the value for continuous undercut for a maximum accumulated length of 10X of weld length. Localized und r-cut less than 3/8 inch in length may be accepted provided the depth does not exceed 3/32 inch for thickness 3/4 inch and less or 1/8 inch for thickness over 3/4 inches.
4.2.7  Cracks 4.2.7.l  Cracks are unacceptable.
4.2.8  Fus.rcn 4.2.8.1   Incomplete fusion between weld metal and base metal is unacceptable.
Attachment 2 (Page 4  of 9)
Page 7  of 12


QV I-09 Rev.1 4,4,31.1 The f'it-up of backing bars is not a basis for rejection.
QVI-09 Rev.     1 4.2.9  Weld S  atter 4.2,9.1    Weld    spatter shall    be  acceptable.
1..1~ld tt'.4.12.1 Weld spatter shall be acceptable.
4.2.10 Arc Strikes 4.2.10.1    Arc strikes are acceptable        provided there are no cracks  ~
4.5 Ca te or E Welds 4.5.1 Oversize Fillet Welds 4.5.1.1 The weld meets or exceeds specified size re-quirements.
4.2.11 Backin    Fitu 4.2. 11.1   'The fitup of backing bars is not       a   basis for rejection.
Either or both f'illet weld legs may exceed design size.Welds may be longer than specified.
~t.        d 4.>.l  The welds on      the main frame member side shall rreet the requirements for Category B.
Continuous welds may be accepted in place of intermittent welds.Unequal leg fil-lets are acceptable, provided the smaller leg meets or exceeds minimum requirements.
4.3.2  The welds on the miscellaneous          metal side shall meet the requirements      for  Category 0.
1 4.5.2 Undersize Welds 4.5.2.1 The fillet leg dimension may not under run the nominal fillet size by more than 1/lo inch.Fillet weld size need not be greater than the thickness of the thinner member.4.5.2.2 Groove welds may be undersize by 5 percent by 1/32 inch, whi.chever is greater.4.5.3 Porosit or Sla Inclusions 4.5.3.1 4.5.4 Profile Porosity or slag inclusions are not a criteria for rejection.
4.4.1 Oversize   Fillet   Welds 4.4.1.1       The weld   shall meet or exceed the specified size requirements,      Either or both fillet weld legs may exceed   design size. Welds may be longer than specified. Continuous welds may be accepted
4.5.4.1 Convexity height, roll over, and weld reinforce-ment are acceptable.
                    'in place of intermittent welds. Unequal leg fillets are acceptable, provided the smaller leg meets or exceeds minimum requirements.
4.4.2 Undersize Welds
: 4. 4. 2.1     The   fill't leg dimensionmoreshallthannot1/16underinch.run the nominal   fillet size   by 4.4.2.2       Groove welds may be undersize by 5 percent or 1/16 inch, whichever      is greater.
Attachment 2 (rag~  5 or 9)
Page 8      of  12


====4.5.5 Cracks====
QVL-09 Rev. 1 4.4.3    Porosit  and Sla 4.4.3.1    Porosity and slag are not    a basis for rejection.
4.5.5.1 All cracks are unacceptable.
: 4. 4. 4  Profile 4.4.4.1   Convexity height, roll 'over, and butt weld  rein-forcement are acceptable.
Attachment 2 (Page 7 of 9)Page 10 of 12 QVZ-09"Rev.1 4.5.6 Fus ion 4.5.6.1 Incomplete fusion between weld metal and base metal is unacceptable.
4.4.5   'usion 4.4.5.1     incomplete fusion between weld metal. and base metal is unacceptable.
4.4.6    Undercut 4.4.6.1    (Same  as  4.2.6.1) 4.4.7    Craters 4.4.7.1    Underfilled groove weld craters shall be accepted provided the depth of underfill is 1/16 inch or less. Lhderfilled single-pass    fillet weld craters shall be accepted provided the crater length is less than 5 percent of the weld length. On multi-pass    fillet welds a crater depth of 1/16 inch or less is acceptable.
: 4. 4.8    Cracks 4.4.8.1    All cracks are unacceptable.
4.4.9          111 4.4.9.1    Misalignm"nt not .in excess of the thinner  member thickness is ac eptable.
4.4.10    Azc  Strikes 4.4.10.1    Ar'c strikes are acceptable provided there are  no cracks.
Attachment 2 (Pag. 6 of 9)
Page 9 of 12


====4.5.7 Undercut====
QV I-09 Rev. 1 4,4,31.1    The  f'it-up of backing bars is not      a  basis for rejection.
4.5.7.1 (Same a 4.2.6.1)4.5.8 4.5.9 4.5.8.1 Misalignment is not a basis for rejection.
1..1        ~ld    tt
Corner'felds 4.5.9,1 Corner welds used to seal ductwork are design-ated partial penetration welds.Such welds do not require full fusion.Meld reinforcement greater than the material thickness shall verify the adequacy of the weld, provided that the toes of the weld have complete fusion.4.5,11 4.5.10.1 Fillet welds joining turning vanes to turning'ane rails or to heavier gauge ductwork may ex-ceed the profile and convexity limits as pre-viously described and are acceptable for this application.
              '.4.12.1      Weld  spatter shall    be  acceptable.
Minor burn-through on vanes will be permitted up to 1/4 inch in length, provided equivalent lengths of fillet welds are added to compensate for welds weakened by burn-through 4.5.10.2.Burn-through is permitted provided there are no visible through-thickness holes.Metal flow on the inside of the duct is per-mitted, provided it is fu.ed completely with the parent metal and metal thickness is not reduced by greater than 50 percent.Arc Strikes 4.5.11.1 Arc strikes are acceptable provided there aze no cracks'ttachment 2 (Page 8 of 9)Page 11 of 12 QYI-09 Rev.1.1~45 4.5512.1 Weld spatter shall be acceptable..
: 4. 5 Ca te or E  Welds 4.5.1      Oversize  Fillet    Welds 4.5.1.1    The weld meets      or exceeds specified size re-quirements.      Either or both f'illet weld legs may exceed design size. Welds may be longer than specified. Continuous welds may be accepted in place of intermittent welds. Unequal leg            fil-lets are acceptable, provided the smaller leg meets or exceeds minimum requirements.
4.5.15~4-4.5.13.1 The fit-up of backing bars is not basis for re-jection.Attachment 2 (Page 9 of 9)Page 12 of 12 4 4 I l(4~:I IX I lt}}
1 4.5.2      Undersize Welds 4.5.2.1    The  fillet leg dimension may not      under run the nominal  fillet size by more than      1/lo inch.
Fillet  weld size need not be greater than the thickness of the thinner member.
4.5.2.2    Groove welds may be undersize by 5 percent by 1/32 inch, whi.chever is greater.
4.5.3      Porosit  or Sla    Inclusions 4.5.3.1    Porosity or slag inclusions are not        a  criteria for rejection.
4.5. 4    Profile 4.5.4.1    Convexity height, roll over, and weld reinforce-ment are acceptable.
4.5.5      Cracks 4.5.5.1    All cracks    are unacceptable.
Attachment 2 (Page 7  of 9)
Page  10  of 12
 
QVZ-09 "Rev. 1 4.5. 6  Fus ion 4.5.6.1    Incomplete fusion between weld metal and base metal is unacceptable.
4.5.7   Undercut 4.5.7.1   (Same a     4.2.6.1) 4.5.8 4.5.8. 1 Misalignment is not     a basis for rejection.
4.5.9  Corner 'felds 4.5.9,1   Corner welds used to seal ductwork are design-ated partial penetration welds. Such welds do not require     full fusion. Meld reinforcement greater than the material thickness shall verify the adequacy of the weld, provided that the toes of the weld have complete fusion.
4.5.10.1 Fillet   welds joining turning   vanes to turning rails or to heavier gauge ductwork may ex-   'ane ceed the profile and convexity limits as pre-viously described and are acceptable for this application. Minor burn-through on vanes will be permitted up to 1/4 inch in length, provided equivalent lengths of fillet welds are added to compensate for welds weakened by burn-through 4.5.10.2. Burn-through is permitted provided there are no visible through-thickness holes.
Metal flow on the inside of the duct is per-mitted, provided     it is fu. ed completely with the parent metal and metal thickness is not reduced by greater than 50 percent.
4.5,11  Arc Strikes 4.5.11.1   Arc strikes are acceptable       provided there aze no cracks'ttachment 2
(Page 8   of 9)
Page   11 of 12
 
QYI-09 Rev. 1
    .1 ~45 4.5.15 ~4-4.5512.1 Weld spatter shall be acceptable..
4.5.13.1 The fit-up of backing bars is not basis for re-jection.
Attachment 2 (Page 9 of 9)
Page 12 of 12
 
4 4
I l(
4   ~
:I IX I
lt}}

Latest revision as of 08:58, 4 February 2020

Rev 1 to Reverification Instruction QVI-09, Special Structural Steel Reinsp Criteria.
ML17277A523
Person / Time
Site: Columbia Energy Northwest icon.png
Issue date: 03/16/1983
From: Crisp H
WASHINGTON PUBLIC POWER SUPPLY SYSTEM
To:
Shared Package
ML17277A522 List:
References
QVI-09, QVI-9, NUDOCS 8304080191
Download: ML17277A523 (14)
v • d • e


Text

NO.

%VI-G9 WAS)lINUTON PUBUC POWER SUPPLY SYSTEM AEV. NO Pa'ih&V EFFECTIVE OATE 3/16 83 REVERIFlGATIOH .iNSTRUCTlON QUALITYAFFECTING Q YES NO TITLE SPECIAL'TRUCTURAL STFEL 'RE N 1.0 PURPOSE/SCOPE This instruction describes the criteria to be used to determine the sign-ificance of discrepancies discovered during the reverification inspec-tions of structural steel welding at WNP-2.

2. 0 DEFINITIONS o Visual Examination Acceptance Criteria - A set of "fitness-for-use" inspectim criteria for determining whether welded structural com-ponents are adequate for their intended purpose. Such criteria shall be approved b'y the 'Architect Engineer in accordance with Paragraphs: 3.7.4 and 5.7.5 of AWS Dl.l,,the Structural Welding Code, 1972 Edition.

o, Structural Steel For the purpose of this instruction, structural steel includes pipe supports, hangers, ductwork, stiffeners, cable trays, unistrut, brackets and similar components, as well as struc'-

tural shapes and plates and miscellaneous steel.

3. 0 PROCEDURE Res onsibilit Action Reverification Inspects the welded structures for confor-

. Inspection Team mance with the requirements of the draw-specifications, codes and standards, 'ngs, except as modified herein. The visual Acceptance Criteria identified'n Ex-'mination Attachment 2, shall be used in lieu of the acceptance criteria specified in AWS Dl.l, The justification for these criteria is included as Attachment 1 to this instruc-tion.

.2 Records the results of the inspections in accordance with QVI-08.

8304080iqi 830323 PDR ADOCK 05000397 8 , . PDR SUPENSEOES ISSUE APPAOV 0 0 PACE 1 OF 1~

'WP.100

~

QV.I-09 Rev. 1

4. 0 REFERENCES 4.1 Quality Verification Program QV'-01 4.2 American Welding Society Structural Welding Code Dl.l, 1972 Edition 4.3 Reverification Inspection Team Concept, QVI-08
5. 0 ATTACHMENTS 5.1 3ustification For WNP-2 Visual Examination Acceptance Criteria 5.2 WNP-2 Visual Examination Acceptance Criteria For Reverification In-spection Of Welded Structures Page 2 of 12

t QVI-09 Rev. 1 JUSTIFICATION FOR WNP-2 VISUAL EXlWINATION ACCEPTANCE CRITERIA 1,0 JUSTIFICATION FOR VISUAL ACCEPTANCE CRITERIA The use of the AWS Dl.l code for the WNP-2 Plant was specified by the Engineer as the applicable structural welding code on behalf of the Owner, and, as such AWS D1.1-72 is identified in the FSAR. Unlike the ASME code, the use of the code is not a mandatory State or NRC regulatory requirement. The Engineer has the authority under the AWS code to modify selected provisions of the 4WS code to suit a particular application.

It is important to understand that the AWS Dl.l code is the applicable structural code for boL'h completed work (first-line inspection) and on-going construction. Site construction and inspection procedures require that welds be made to the applicable AWS crit ria and that. the first-line inspection be performed in accordance with the AWS D1.1 code. In cases where deviations are evaluated by the Engineer to be non-significant in terms of the ability of the component to perform its designed function,'he Engineer has the authority to disposition the deviation "accept-as-is" as appropriate, or compensate for the deviation by additional evaluation or have construction performed to an approved, revised design.

During the initial QVP reinspection of completed .work, a number of minor deviations with respect to sow AWS criteria were encountered which were evaluated by the Engineer as acceptable in certain categories of applica-tion. Since the specific deviations had been evaluated by the Engineer to be acceptable for these categories of application, the processing of additional deviations of the sam type in the same categories served no purpose.

Thus, a generic disposition was developed by the Engineer for acceptance

.of specified deviations, from the AWS 01.1, l972 code in selected applica-tions. This generic disposition has taken the form of a revised inspec-tion criteria for use by the QVP for reinspection of completed work.

These criteria are embodied within the reverification inspection require-ments in Attachment 2 of QVI-09.

Attachment 1 (Page 1 of 1)

Page 3 of 12

QVI-09 Rev. 1 HNP-2 PROJECT VISUAL EXAMINATION ACCEPTANCE CRITERIA FOR REVERIFICATION INSPECTION OF" l(ELDED STRUCTURES

(.

Approved:

Burns 8 Roe, Inc.

Date:

j'-/7- P g Attachment 2 (Page 1 of 9)

Page 4 of 12

QVI-O9 Rev. l 1.0 SCOPE This document provides visual examination acceptance criteria for reveri-fication inspection of structural steel and miscellaneous metal welding performed in accordance with AWS Dl.l, the Structural Welding Code.

These criteria reflect requirements consistent with the engineering approval specified, in AWS Dl.l for evaluation of structural welding.

This document also includes acceptance standards for light gauge HVAC ductwork, and other systems which are not specifically covered by AWS D.1. 1.

1.1 These, criteria shall be used by Construction Quality Control for pe forming reverification inspection by including it on the QCIR as an applicable inspection reference criteria document to evaluate deviations to AWS Dl.l.

2.0 CODES AND STANDARDS The criteria in this document provide the basis for visual examination of AWS Dl.l welding. The required engineering approval, as specified in Paragraphs 3.7.4 and 3.7.5 of AWS Dl.l has been provided by the Architect Engineer. Authorization for this is given in Paragraph l.l of AWS Dl.l.

3.0 BASIS FOR EVALUATION The applicable weld categories will be entered on the QCIR as a part of the inspection reference criteria based upon the definitions described below.

3.l Category A Welds gust be in accordanc with the visual acceptance criteria of the specified section of AWS D1.1. This category applies to elements of fans, cranes, rotating equipment, and other machinery subject to frequent stress reversals.

Have, an acceptance level modified to meet the required service con-ditions. This category applies to members of the building frame that carry princioal design loads, radial beams, sacrificial shield wall, pipe whip rI'.straints, pipe supports, and similar principal load bearing structures.

Attachment 2 (Page 2 of 9)

Page 5 of 12

qvl-0~

Rev. 1 3.3 Cate or C Welds Are connections between Category 0 Steel and Miscellaneous Metal.

3.4 Cate or D Welds .

Are not part of the main building frame, but- rather provide support or framing for electrical, instrumentation, and HVAC systems, com-ponents and equipment. Also included in the D Category are welds joining miscellaneous metal including, but not limited to, stair-ways, embedments, fan housings, doors, windows, hatches, frames,

.ledger angles, gratings and their supports.

Is an acceptance level established for relatively thin materials such as. HVAC ductwork, cable trays, and unistrut supports.

4. 0 ACCEPTANCE CRITERIA Acceptance shall be based on the weld joint meeting each criteria listed for the applicable category. Skewed joints will be evaluated in accordance with Cont~act Specifications and Project Engineering

~tld Directives.

4.1.1 Category A welds must comply with the visual examination requirements of the specified section of A'WS Dl.l.

4.2 Cate or B Welds 4.2.1 Oversize Fillet Welds The weld shall meet or exceed the specified size require-ments. Either or both fillet weld legs may exceed design size. Welds may be longer than specified. Continuous welds may be accepted in place of intermittent welds.

Unequal leg fillet welds are acceptable, provided the smaller leg meets or exceeds minimum requirements.

4.2.2, Undersize Welds 4.2.2.1 The fillet leg dimension shall not under run the nominal fillet size by more than l/16 inch. For flange to web joints the undersize condition may not be within two flange thicknesses of the weld end.

Attachment 2 (Page 3 of 9)

Page 6 of 12

QV I-09 Rev. 1 4.2.2.2 Groove welds may be underfilled by 5 percent or 1/32-inch, whichever is greater.

4.2.3 Porosit and Sla 4.2.3.1 The weld may contain a maximum of 5 percent by surface area of unaligned porosity and/or slag.

4.2. 4 Profile 4.2.4.1 Convex-'ty height, roll over, and butt weld rein-forcement are acceptable.

4.2.5 Craters 4.2.5.1 The weld may have an underfilled crater, pro-vided the underfill depth does not exceed 1/16 inch, and the crater has a smooth contour blend-ing gradually with the adjacent weld and base metal without acute notches.

4.2.6 Undercut 4.2'.6.1 Continuous undercut shall not be greater than:

1/32 inch for material 3/8 inch and less; 1/16 inch f'r material over 3/8 inch thick.

Intermittant undercut may be twice the value for continuous undercut for a maximum accumulated length of 10X of weld length. Localized und r-cut less than 3/8 inch in length may be accepted provided the depth does not exceed 3/32 inch for thickness 3/4 inch and less or 1/8 inch for thickness over 3/4 inches.

4.2.7 Cracks 4.2.7.l Cracks are unacceptable.

4.2.8 Fus.rcn 4.2.8.1 Incomplete fusion between weld metal and base metal is unacceptable.

Attachment 2 (Page 4 of 9)

Page 7 of 12

QVI-09 Rev. 1 4.2.9 Weld S atter 4.2,9.1 Weld spatter shall be acceptable.

4.2.10 Arc Strikes 4.2.10.1 Arc strikes are acceptable provided there are no cracks ~

4.2.11 Backin Fitu 4.2. 11.1 'The fitup of backing bars is not a basis for rejection.

~t. d 4.>.l The welds on the main frame member side shall rreet the requirements for Category B.

4.3.2 The welds on the miscellaneous metal side shall meet the requirements for Category 0.

4.4.1 Oversize Fillet Welds 4.4.1.1 The weld shall meet or exceed the specified size requirements, Either or both fillet weld legs may exceed design size. Welds may be longer than specified. Continuous welds may be accepted

'in place of intermittent welds. Unequal leg fillets are acceptable, provided the smaller leg meets or exceeds minimum requirements.

4.4.2 Undersize Welds

4. 4. 2.1 The fill't leg dimensionmoreshallthannot1/16underinch.run the nominal fillet size by 4.4.2.2 Groove welds may be undersize by 5 percent or 1/16 inch, whichever is greater.

Attachment 2 (rag~ 5 or 9)

Page 8 of 12

QVL-09 Rev. 1 4.4.3 Porosit and Sla 4.4.3.1 Porosity and slag are not a basis for rejection.

4. 4. 4 Profile 4.4.4.1 Convexity height, roll 'over, and butt weld rein-forcement are acceptable.

4.4.5 'usion 4.4.5.1 incomplete fusion between weld metal. and base metal is unacceptable.

4.4.6 Undercut 4.4.6.1 (Same as 4.2.6.1) 4.4.7 Craters 4.4.7.1 Underfilled groove weld craters shall be accepted provided the depth of underfill is 1/16 inch or less. Lhderfilled single-pass fillet weld craters shall be accepted provided the crater length is less than 5 percent of the weld length. On multi-pass fillet welds a crater depth of 1/16 inch or less is acceptable.

4. 4.8 Cracks 4.4.8.1 All cracks are unacceptable.

4.4.9 111 4.4.9.1 Misalignm"nt not .in excess of the thinner member thickness is ac eptable.

4.4.10 Azc Strikes 4.4.10.1 Ar'c strikes are acceptable provided there are no cracks.

Attachment 2 (Pag. 6 of 9)

Page 9 of 12

QV I-09 Rev. 1 4,4,31.1 The f'it-up of backing bars is not a basis for rejection.

1..1 ~ld tt

'.4.12.1 Weld spatter shall be acceptable.

4. 5 Ca te or E Welds 4.5.1 Oversize Fillet Welds 4.5.1.1 The weld meets or exceeds specified size re-quirements. Either or both f'illet weld legs may exceed design size. Welds may be longer than specified. Continuous welds may be accepted in place of intermittent welds. Unequal leg fil-lets are acceptable, provided the smaller leg meets or exceeds minimum requirements.

1 4.5.2 Undersize Welds 4.5.2.1 The fillet leg dimension may not under run the nominal fillet size by more than 1/lo inch.

Fillet weld size need not be greater than the thickness of the thinner member.

4.5.2.2 Groove welds may be undersize by 5 percent by 1/32 inch, whi.chever is greater.

4.5.3 Porosit or Sla Inclusions 4.5.3.1 Porosity or slag inclusions are not a criteria for rejection.

4.5. 4 Profile 4.5.4.1 Convexity height, roll over, and weld reinforce-ment are acceptable.

4.5.5 Cracks 4.5.5.1 All cracks are unacceptable.

Attachment 2 (Page 7 of 9)

Page 10 of 12

QVZ-09 "Rev. 1 4.5. 6 Fus ion 4.5.6.1 Incomplete fusion between weld metal and base metal is unacceptable.

4.5.7 Undercut 4.5.7.1 (Same a 4.2.6.1) 4.5.8 4.5.8. 1 Misalignment is not a basis for rejection.

4.5.9 Corner 'felds 4.5.9,1 Corner welds used to seal ductwork are design-ated partial penetration welds. Such welds do not require full fusion. Meld reinforcement greater than the material thickness shall verify the adequacy of the weld, provided that the toes of the weld have complete fusion.

4.5.10.1 Fillet welds joining turning vanes to turning rails or to heavier gauge ductwork may ex- 'ane ceed the profile and convexity limits as pre-viously described and are acceptable for this application. Minor burn-through on vanes will be permitted up to 1/4 inch in length, provided equivalent lengths of fillet welds are added to compensate for welds weakened by burn-through 4.5.10.2. Burn-through is permitted provided there are no visible through-thickness holes.

Metal flow on the inside of the duct is per-mitted, provided it is fu. ed completely with the parent metal and metal thickness is not reduced by greater than 50 percent.

4.5,11 Arc Strikes 4.5.11.1 Arc strikes are acceptable provided there aze no cracks'ttachment 2

(Page 8 of 9)

Page 11 of 12

QYI-09 Rev. 1

.1 ~45 4.5.15 ~4-4.5512.1 Weld spatter shall be acceptable..

4.5.13.1 The fit-up of backing bars is not basis for re-jection.

Attachment 2 (Page 9 of 9)

Page 12 of 12

4 4

I l(

4 ~

I IX I

lt

Retrieved from "https://kanterella.com/w/index.php?title=ML17277A523&oldid=2432017"