ML12107A062: Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(Created page by program invented by StriderTol)
Line 14: Line 14:
| page count = 4
| page count = 4
| project = TAC:ME8347
| project = TAC:ME8347
| stage = Request
| stage = RAI
}}
}}


Line 25: Line 25:


By letter dated April 6, 2011, Exelon Generation Company, the licensee for Quad Cities Nuclear Power Station, Unit 2, (Q2), submitted for staff review and approval a relief request for an instrument penetration repair.
By letter dated April 6, 2011, Exelon Generation Company, the licensee for Quad Cities Nuclear Power Station, Unit 2, (Q2), submitted for staff review and approval a relief request for an instrument penetration repair.
In order to complete its review of the licensee's submittal, the Nuclear Regulatory Commission (NRC) staff requires a response to the following questions:  
In order to complete its review of the licensee's submittal, the Nuclear Regulatory Commission (NRC) staff requires a response to the following questions:
: 1. How has it been established that the flaw is not a threat to vessel integrity?  
: 1. How has it been established that the flaw is not a threat to vessel integrity?
: a. Justify any assumptions regarding the nature of the flaw, i. Location, ii. Cause, iii. Extent;  b. Justify lack of examination to even qualitatively describe flaw through direct observation,  c. Justify the lack of examination to demonstrate the flaw/leak path is not through the vessel steel rather than the J-groove weld or nozzle.  
: a. Justify any assumptions regarding the nature of the flaw, i. Location, ii. Cause, iii. Extent;  b. Justify lack of examination to even qualitatively describe flaw through direct observation,  c. Justify the lack of examination to demonstrate the flaw/leak path is not through the vessel steel rather than the J-groove weld or nozzle.
: 2. Specify the ASME specifications to which the repair materials (nozzle, weld metal, etc.) adhere (SA-XXX, etc.).  
: 2. Specify the ASME specifications to which the repair materials (nozzle, weld metal, etc.) adhere (SA-XXX, etc.).
: 3. Describe the steps of the proposed repair in detail, including the machining, preparation, and examinations.  
: 3. Describe the steps of the proposed repair in detail, including the machining, preparation, and examinations.
: 4. Clarify why Code Case N-638-4 is a cceptable for use on the Q2 RV, st ated in the application as being made of SA-302, Grade B, when N-638-4 states "this Case shall not be used to repair SA-302, Grade B, unless-"  
: 4. Clarify why Code Case N-638-4 is a cceptable for use on the Q2 RV, st ated in the application as being made of SA-302, Grade B, when N-638-4 states "this Case shall not be used to repair SA-302, Grade B, unless-"  


2 5. Specify the nature of the manual non-temper bead welding technique used to attach the new nozzle to the weld pad. Specifically,  a. By which edition and addenda of the ASME Code will the procedure be qualified, b. What filler material will be used, c. Provide a discussion of the welding process, d. Explain how the partial penetration surface put in to the weld pad will be inspected to ensure that no flaws in the weld-pad will contact the non-temper bead manual welding material.  
2 5. Specify the nature of the manual non-temper bead welding technique used to attach the new nozzle to the weld pad. Specifically,  a. By which edition and addenda of the ASME Code will the procedure be qualified, b. What filler material will be used, c. Provide a discussion of the welding process, d. Explain how the partial penetration surface put in to the weld pad will be inspected to ensure that no flaws in the weld-pad will contact the non-temper bead manual welding material.
: 6. Discuss the potential of increased localized st resses on the reactor vessel shell at the nozzle penetration location when the weld pad is installed. Provide the dimensions of the planned weld pad:
: 6. Discuss the potential of increased localized st resses on the reactor vessel shell at the nozzle penetration location when the weld pad is installed. Provide the dimensions of the planned weld pad:
shape, thickness, width, and height.  
shape, thickness, width, and height.
: 7. Describe the pre and post-repair inspections and testing that will be performed as part of the repair process including the required demonstration for ultrasonic examination of the repaired volume required by condition (1) of Regulatory Guide 1.1.47 on Code Case N-638-4. Specifically,  a. What examinations/inspections will be performed,  reference specific ASME Code requirements under which the examinations will be performed, b. The nature of the examinations/inspections (P DI-qualified UT, ASME Section XXXX VT-1, etc.), c. What are the acceptance criteria, refere nce specific ASME Code requirements, d. It appears that the only examination for the installation of the weld pad is progressive penetrant testing. Discuss why a volumetric examination will not be performed on the weld pad as part of acceptance (pre-service) examination.  
: 7. Describe the pre and post-repair inspections and testing that will be performed as part of the repair process including the required demonstration for ultrasonic examination of the repaired volume required by condition (1) of Regulatory Guide 1.1.47 on Code Case N-638-4. Specifically,  a. What examinations/inspections will be performed,  reference specific ASME Code requirements under which the examinations will be performed, b. The nature of the examinations/inspections (P DI-qualified UT, ASME Section XXXX VT-1, etc.), c. What are the acceptance criteria, refere nce specific ASME Code requirements, d. It appears that the only examination for the installation of the weld pad is progressive penetrant testing. Discuss why a volumetric examination will not be performed on the weld pad as part of acceptance (pre-service) examination.
: 8. The proposed repair will result in a gap between th e original and new nozzles inside the bore of the reactor vessel shell. The gap region may be susceptible to crevice or general corrosion affecting the reactor vessel shell and the new nozzle. Provide anal ysis to demonstrate that the corrosion of the shell will not affect the structural integrity of the new nozzle and the reactor vessel shell.  
: 8. The proposed repair will result in a gap between th e original and new nozzles inside the bore of the reactor vessel shell. The gap region may be susceptible to crevice or general corrosion affecting the reactor vessel shell and the new nozzle. Provide anal ysis to demonstrate that the corrosion of the shell will not affect the structural integrity of the new nozzle and the reactor vessel shell.
: 9. Application Section 5, Basis, (C) states that a flaw evaluation will be performed for one cycle of operation. The licensee stated that qualification beyond one cycle will be performed based on detailed residual stress analysis and fatigue crack growth analysis.  
: 9. Application Section 5, Basis, (C) states that a flaw evaluation will be performed for one cycle of operation. The licensee stated that qualification beyond one cycle will be performed based on detailed residual stress analysis and fatigue crack growth analysis.
: a. Submit the one-cycle flaw evaluation, b. Provide a commitment with a specific date that a detailed flaw evaluation for the remaining life of the plant will be submitted, c. Discuss how the licensee can demonstrate the acceptability of the repair or the one cycle flaw evaluation without an examination, after one cycle of operation after the repair,
: a. Submit the one-cycle flaw evaluation, b. Provide a commitment with a specific date that a detailed flaw evaluation for the remaining life of the plant will be submitted, c. Discuss how the licensee can demonstrate the acceptability of the repair or the one cycle flaw evaluation without an examination, after one cycle of operation after the repair,
: d. Explain why the flaw evaluation requires two pha ses (i.e., one cycle calculation and beyond one cycle calculation), e. Confirm that flaw analysis will include or bo und transient loads and conditions beyond normal operation, f. Specify what load conditions the flaw analysis bound.  
: d. Explain why the flaw evaluation requires two pha ses (i.e., one cycle calculation and beyond one cycle calculation), e. Confirm that flaw analysis will include or bo und transient loads and conditions beyond normal operation, f. Specify what load conditions the flaw analysis bound.
: 10. Submit the design analysis to demonstrate that the new nozzle will not eject from the reactor vessel shell under the design conditions and that it satisfies the requirements of the ASME Code, Section III, NB-3200.
: 10. Submit the design analysis to demonstrate that the new nozzle will not eject from the reactor vessel shell under the design conditions and that it satisfies the requirements of the ASME Code, Section III, NB-3200.
3 Hearing Identifier:  NRR_PMDA Email Number:  323  Mail Envelope Properties  (1A97AE0578A58B46BC77AA0B5DBD72023BF3D445CB)   
3 Hearing Identifier:  NRR_PMDA Email Number:  323  Mail Envelope Properties  (1A97AE0578A58B46BC77AA0B5DBD72023BF3D445CB)   

Revision as of 01:27, 30 April 2019

Preliminary RAIs Regarding Quad Cities, Unit 2 Relief Request I4R-19
ML12107A062
Person / Time
Site: Quad Cities Constellation icon.png
Issue date: 04/10/2012
From: Joel Wiebe
Division of Operating Reactor Licensing
To: Gullott D, Bauer J, Matthews M
Exelon Corp
References
TAC ME8347
Download: ML12107A062 (4)
v • d • e


Text

1 NRR-PMDAPEm Resource From: Wiebe, Joel Sent: Tuesday, April 10, 2012 2:43 PM To: David Gullott; Joseph Bauer; Mitchel Mathews

Subject:

Preliminary RAIs Regarding Quad Ci ties, Unit 2 Relief Request I4R-19The purpose of preliminary RAIs are to ensure the questions are clear and understandable. Let me know if we need to have a teleconference regarding these RAIs.

REQUEST FOR ADDITIONAL INFORMATION REGARDING QUAD CITIES NUCLEAR POWER STATION, UNIT 2 VESSEL PENETRATION RELIEF REQUEST NO. I4R-19 DOCKET NO. 50-265 (TAC NO. ME8347)

By letter dated April 6, 2011, Exelon Generation Company, the licensee for Quad Cities Nuclear Power Station, Unit 2, (Q2), submitted for staff review and approval a relief request for an instrument penetration repair.

In order to complete its review of the licensee's submittal, the Nuclear Regulatory Commission (NRC) staff requires a response to the following questions:

1. How has it been established that the flaw is not a threat to vessel integrity?
a. Justify any assumptions regarding the nature of the flaw, i. Location, ii. Cause, iii. Extent; b. Justify lack of examination to even qualitatively describe flaw through direct observation, c. Justify the lack of examination to demonstrate the flaw/leak path is not through the vessel steel rather than the J-groove weld or nozzle.
2. Specify the ASME specifications to which the repair materials (nozzle, weld metal, etc.) adhere (SA-XXX, etc.).
3. Describe the steps of the proposed repair in detail, including the machining, preparation, and examinations.
4. Clarify why Code Case N-638-4 is a cceptable for use on the Q2 RV, st ated in the application as being made of SA-302, Grade B, when N-638-4 states "this Case shall not be used to repair SA-302, Grade B, unless-"

2 5. Specify the nature of the manual non-temper bead welding technique used to attach the new nozzle to the weld pad. Specifically, a. By which edition and addenda of the ASME Code will the procedure be qualified, b. What filler material will be used, c. Provide a discussion of the welding process, d. Explain how the partial penetration surface put in to the weld pad will be inspected to ensure that no flaws in the weld-pad will contact the non-temper bead manual welding material.

6. Discuss the potential of increased localized st resses on the reactor vessel shell at the nozzle penetration location when the weld pad is installed. Provide the dimensions of the planned weld pad:

shape, thickness, width, and height.

7. Describe the pre and post-repair inspections and testing that will be performed as part of the repair process including the required demonstration for ultrasonic examination of the repaired volume required by condition (1) of Regulatory Guide 1.1.47 on Code Case N-638-4. Specifically, a. What examinations/inspections will be performed, reference specific ASME Code requirements under which the examinations will be performed, b. The nature of the examinations/inspections (P DI-qualified UT, ASME Section XXXX VT-1, etc.), c. What are the acceptance criteria, refere nce specific ASME Code requirements, d. It appears that the only examination for the installation of the weld pad is progressive penetrant testing. Discuss why a volumetric examination will not be performed on the weld pad as part of acceptance (pre-service) examination.
8. The proposed repair will result in a gap between th e original and new nozzles inside the bore of the reactor vessel shell. The gap region may be susceptible to crevice or general corrosion affecting the reactor vessel shell and the new nozzle. Provide anal ysis to demonstrate that the corrosion of the shell will not affect the structural integrity of the new nozzle and the reactor vessel shell.
9. Application Section 5, Basis, (C) states that a flaw evaluation will be performed for one cycle of operation. The licensee stated that qualification beyond one cycle will be performed based on detailed residual stress analysis and fatigue crack growth analysis.
a. Submit the one-cycle flaw evaluation, b. Provide a commitment with a specific date that a detailed flaw evaluation for the remaining life of the plant will be submitted, c. Discuss how the licensee can demonstrate the acceptability of the repair or the one cycle flaw evaluation without an examination, after one cycle of operation after the repair,
d. Explain why the flaw evaluation requires two pha ses (i.e., one cycle calculation and beyond one cycle calculation), e. Confirm that flaw analysis will include or bo und transient loads and conditions beyond normal operation, f. Specify what load conditions the flaw analysis bound.
10. Submit the design analysis to demonstrate that the new nozzle will not eject from the reactor vessel shell under the design conditions and that it satisfies the requirements of the ASME Code,Section III, NB-3200.

3 Hearing Identifier: NRR_PMDA Email Number: 323 Mail Envelope Properties (1A97AE0578A58B46BC77AA0B5DBD72023BF3D445CB)

Subject:

Preliminary RAIs Regarding Quad Cities, Unit 2 Relief Request I4R-19 Sent Date: 4/10/2012 2:42:50 PM Received Date: 4/10/2012 2:42:00 PM From: Wiebe, Joel Created By: Joel.Wiebe@nrc.gov Recipients: "David Gullott" <David.Gullott@ExelonCorp.com>

Tracking Status: None "Joseph Bauer" <Joseph.Bauer@exeloncorp.com>

Tracking Status: None "Mitchel Mathews" <Mitchel.Mathews@exeloncorp.com> Tracking Status: None

Post Office: HQCLSTR02.nrc.gov Files Size Date & Time MESSAGE 5212 4/10/2012 2:42:00 PM Options Priority: Standard Return Notification: No Reply Requested: No Sensitivity: Normal Expiration Date: Recipients Received:

Retrieved from "https://kanterella.com/w/index.php?title=ML12107A062&oldid=1552060"