ML111250544

From kanterella
Jump to navigation Jump to search
Core Operating Limits Report, COLR1-20
ML111250544
Person / Time
Site: Nine Mile Point Constellation icon.png
Issue date: 04/26/2011
From: Sterio A
Constellation Energy Group, EDF Group, Nine Mile Point
To:
Document Control Desk, Office of Nuclear Reactor Regulation
References
Download: ML111250544 (26)
v • d • e


Text

CENG.

a joint venture of P.O. Box 63 Lycoming, New York 13093 0Constellation je SEnergy eF NINE MILE POINT NUCLEAR STATION April 26, 2011 U.S. Nuclear Regulatory Commission Washington, D.C. 20555-0001 ATTENTION: Document Control Desk

SUBJECT:

Nine Mile Point Nuclear Station Unit No. 1; Docket No. 50-220 Nine Mile Point Unit 1 Core Operating Limits Report, COLRI-20 Enclosed is a copy of the Core Operating Limits Report, COLR1-20, Revision 0, for Nine Mile Point Unit 1 (NMP 1). This report is being submitted pursuant to NMP1 Technical Specification 6.6.5.d.

Should you have any questions regarding the information in this submittal, please contact John J. Dosa, Director Licensing, at (315) 349-5219.

Very truly yours, Alex D. Sterio Manager Engineering Services (Acting)

ADS/RJC

Enclosure:

Nine Mile Point Unit 1 Core Operating Limits Report, COLR1-20, Revision 0 cc: Regional Administrator, Region L,NRC Project Manager, NRC Resident Inspector, NRC

ý'ool

"ýA-

ENCLOSURE Nine Mile Point Unit 1 Core Operating Limits Report COLR1-20, Revision 0 Nine Mile Point Nuclear Station, LLC April 26, 2011

'N[NE MILE POINT UNITI.

CORE OPERATING LIMITS REPORT DocumentNo.: COLRi-20 Revisionu' Name Title Date ftepired byý:

C. Leinc 1ue[Enghuner R~ve~vied liv:

Indepen6en~t]Y RevieWed by:, Fuel.Enginee-Approved by': /A1

'R. Clowe Fel inenng John Darweesh Appro ved, by--

'7

~ / ~'~t4j* ,A /

CI/ 1" PW Wengloski Supervisor, Nuclca~r Fuels e

7his:Centrollejl'd Oxwunies 5'lX'cii "Coreo'rui ThjS~for',uLSe III c njuion wilh'ti~cNine X11ie :Vnt .ltirii !ý*ccthdln'i al pitis ~may.1bc dhanud Txuf~i&m.*umceni' throughea rýsu f 1CLmire do'0umenft.

COLRI-20 NINE MILE POINT UNIT 1 RevisionO CORE OPERATING LIMITS REPORT TERMS AND DEFINITIONS Average Planar Linear Heat Generation Rate (APLHGR)

The Average Planar Linear Heat Generation Rate (APLHGR) shall be applicable to a specific planar height and is.equal to" the sum of the heat generation rate per unit length ,offuel rod for all fuel. rods in the specified bundle at.the especified height, divided by the number of fuel rods in thefuel bundle.at that height BOC Beginninrg of Cycle Maxiumum Fraction of Limiting Power Derisity (MFLPD),

The highest value of the fraction of limiting power density which exists in the core.

EOR End of Rated Conditions (i.e. cycle. exposure at I00% power, 100% flow, all rods-out,-all feedwater heaters in.service and equilibrium:xenon)

MCPRflowdependent multiplier K(P)

MCPRgpower dependent multiplier LHGRFAC(P)

P ower dependent LHGR correction factor Linear HeatGeheration Rate (LHGR)

Theheat generation per unit lehigth of fuel rod. It'is the integralofthe heat:flux over the heat transfer area associated with the-fuel leigth.

MAPLHGR, Maximum Average Planar Linear Heat Generat ion.Rate Minimum Critical:Power Ratio (MCPR)

The: mitimumin-core critical power ratio

.RSLD Reload. SpecifiicLattice Data Document MDFWP.

Motor driven feedwater. pump TDFWP.

Turbine driVen feedwater pump Page i

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT Table of Contents Page-1.0 AVERAGE PLANAR LINEAR HEAT GENERATION RATE (APLHGR) 1.1 Limits for Technical Specification 3,.7.a

,1.2 Limits for Technical Specification 3.1.7.e 2.0 MINIMUM CRITICAL POWER RATIO (MCPR) 8" 2.1 Limits for TechnicalSpecification 3.I.7.c 8 22, Limits for Technical Specification 3.1.7.e 8 3.0 LINEAR HEAT GENERATION RATE (LHGR) 16 3.1 Limits for Technica!'Specifliations3.1.7.b. 16 4.0 POWERIFLOW RELATIONSHIP DURING OPERATION 18 4.1 Limits for Technical Specification-Table.1.7.d and e 1l8

5.0 REFERENCES

FOR TECHNiCAL-SPECIFICATIONS 20 6.0 SOURCE DOCUMENTS 21:

Pagei

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT 1.0 AVERAGE PLANAR LINEAR HEAT GENERATION RATE (APLHGR) 1.! Limits for TechnicalSpecification 3.1.7.a

.During power operations, :the APLHGR(s)for each fuel type as a function of AVERAGE PLANAR EXPOSURE shall not exceed the limiting values shown for GE 1in Table Ia, l b, Ic, and Id, or th* limiting values shown for GNF2 in Table le

.and If.

1.2Limits for Technical Specification 3.1.7.e During partial loop operation with.four recirculation loops in operation, the APLHGR

.as a function 'ofaverage planre xposure shall not exceeed98:percent of the limitingi values shown for GEI I :"in Tabled la, Ib, Ic, and I:d and 99 percent of the limiting values shown for GNF2 in Table I e.and I f.

During partial loop operation withthree, recirculation loops in:0peration, the APLHGR as a function of average planar exposure shall not exceeed 98 percent ofthe limiting values shown forGEI I in Table I a, I Ic, and I dand99 percent of the limiting values. shown for:GNF2'in'Table IWe.and If.

Page 1 of 21

COLRI-20 NINE MILE POINT UNIT 1 Revision 0 CORE OPERATING LIMITS REPORT Table la MAPLHGR VERSUS AVERAGE PLANAR EXPOSURE Average PlanarExposure MAPLHGRLimits(kWlft) (1)

GWd/ST Bundle, Bundle 2586. 2831 0.00 9.63 9:51

.20 9.63 9.51 1.00 9.60 9,48 5 .00 9'40 9-35 10.00 9.37 920 15.00 9.224 9.07 20.00 8:76 .860

25.00 8..34 8.15 35;00 8.10 8.05 45.00 8.03 8.06 55.00 8.02 8.11

.65.00 6.18 820 (1)'These MAPLHGRs are not lattice dependent, therefore the values showna also correspond to the limiting value.for the most limiting lattice for use when hand calculations are required.

Bundle Type .ID GEl i-P9DUB376-12GZ-IOOT-145-T6-2586 2586; GEl1 0P9DU B382-13GZ-iOOT-145-T6-2831 .2831 Page 2 of 21

COLR1 -20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LMITS REPORT Table lb MAPLHGR VERSUSAVERAGE PLANAR:EXPOSURE Bundle Type:: GEI -P9DUB381-13GZ-1 OT1145-T6-2945 4GEI 1)

Average Planar _'MAPLHGR Limit*st1 (k*ift) ___

Exposure Lattice Lattice Lattice Lattice Lattice Lattice Most GWd1ST 7433 7434 7435 7436 7437 7438 Limiting 0.00 9R61 961 ;957 '9'57 9.57

  • 957 9.57 020 .961 961 19.57 9.57 9.57 9.57 9.57 1.00 _9.57. ,9i57 9.56 9.56, 9.56 9.56 9.56 5.00 942 9.42 946 9.46 .946 9.46 9.42 10.00 .937 . 937' 9.34, 9.34 9.34 9.34 9;34 15.00. .922 9.22 9.23, '9.23 9.23ý 9.23 *9.22 8 919. 9.19, 919 9.19 918 20.00. 918 25.00 850 850 8.47 8.47 847 847 847
35.00 819 89 8.28 8,28 828 8.28 8:1.9 45.00 8227 8.327' 8.27 .. .27 8.827 8,27 .8.27 55.00 ' 8.31 8.31 831 8;31 8&31 8.31 ' 8131

_ 5___0 " o 8.38

`838 8.38

,88.38. 8.8

'8.38 " 8.38 (1) These MAPLHGR are lattice dependent.Tlhe values shown in the Most LimitingColIumn correspondcto the:

calculations. are required. Lattice descriptions limiting value for the most limiting lattice for use when hand are contained in the RSLD.

Page 3 of 21

COLR1-20 NINE MILE POINT UNIT 1 Revision 0 COREOPERATING LIMITS REPORT Table Ic MAPLHGR VERSUS AVERAGE PLANAREXPOSURE Bundle Type: GEl I -P9DUB38114GZ-1 OOT-145-T6.2946 (GEl I)

Average Planar _ _MAPLHGR Limitsl' (kw/ft) _

Exposure Lattice Lattice Lattice Lattice. Lattice, Lattice Most GWd/ST 7433 7439 7440 7441 7442 7443 Limiting 0.00 10.24 10,24 10.19 10.19 10.19, 10.19 10.19 0.20 1024 .10.24 10,19 " 10.19 10.19 10.19 -10.1.9 1.00 1,0_20 10,20 10.19 10.19 '1019 11910.9 5.00 9 91 9!91 4.85- 9.85 9,985 9.;85 10.00 942 9:42 9.34, 9.34 934 934 9.34 15.00 9.22 9:22: 9..19 919 9.19 919 9.19

20.00 9.18 9.18 9.19 9.19 9.19 9 19
  • 9.18

,25.00 8.64 8.64 8&63 8M63 8,63 . 8.663 8.63 35.00 8.08 8.08 8.08 8.08 8.08 8.08 8.08 45.00 8.02 8.02, 7.99 7 99 7.99 7.99 7.99 55.00 .[ 8.00 ;8.00 7.99 7.99 7.99 7.99 7.99 65;00 7.97 7:97 7'96' 7.96$ 7.96. .7.96 7.96 (1) These MAPLHGR ýare lattice dependent . The values shown in the Most Limiting olumn correspond to the:

limiting value for the most limiting lattice for use when hand calculations are require'. Lattice descriptions are contained in,.the RSLD.

Page-4 of 21

COLR1 -20 NINE MILE POINT UNIT 1 Revision 0 CORE OPERATING LIMITS REPORT Table Id MAPLHGR VERSUS AVERAGE PLANAR EXPOSURE Bundle Type: GEl I-P9DUB380-13GZ-1OOT-145-T6-2948 (GEl 1)

Average Planar MAPLHGR Limits"' (kw/ft)

Exposure Lattice Lattice Lattice Lattice Lattice Lattice Most GWd/ST 7433 7449 7450 7451 7447 7448 Limiting 0.00 9.71 9.71 9.69 9.69 9.69 9.69 9.69 0.20 9.71 9.71 9.69 9.69 9.69 9.69 9.69 1.00 9.68 9.68 9.67 9.67 9.67 9.67 9.67 5.00 9.56 9.56 9.50 9.50 9.50 9.50 9.50 10.00 9.38 9.38 9.32 9.32 9.32 9.32 9.32 15.00 9.23 9.23 9.24 9.24 9.24 9.24 9.23 20.00 9.28 9.28 9.31 9.31 9.31 9.31 9.28 25.00 8.43 8.43 8.45 8.45 8.45 8.45 8.43 35.00 8.09 8.09 8.09 8.09 8.09 8.09 8.09 45.00 7.98 7.98 8.02 8.02 8.02 8.02 7.98 55.00 7.97 7.97 7.98 7.98 7.98 7.98 7.97 65.00 7.91 7.91 7.93 7.93 7.93 7.93 7.91 (1) These MAPLHGR are lattice dependent. The values shown in the Most Limiting Column correspond to the limiting value for the most limiting lattice for use when hand calculations are required. Lattice descriptions are contained in the RSLD.

Page 5 of 21

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT Table le MAPLHGR VERSUS AVERAGE PLANAR EXPOSURE Bundle Type: GNF2-P10DG28384-16GZ-100T2-145-T6-3351 (GNF2)

Average Planar Exposure MAPLHGR Limits (kW/ft)"(1)

GWdS.ST KW/ft 0.00 7.90 0.20 7.90 1.00 7.990 5.00, 7.79 10.00 7.68 15.00 7.60 20.00. 7.12 25ý00. 673 35.00e. 6.57 45.00 .6.35 55,00, 6.24 65.00 6:15 (1)These MAPLHGRs are not lattice dependent,.therefore the values, shwn: alsocorrespond to the limiting value for the mostitmiting lattice for use when hand calculations are:required.

Page 6 of 21

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT Table If MAPLHGR VERSUS AVERAGE PLANAR EXPOSURE Bundle Type: GNF2-P1 01G2B386-13GZ-A 00T2-145-T6-3352 (GNF2)

Average Panar ExPOsUMAPLHRLimits(kWft QGWd!ST. KWIft 0.00 .. .. . 7,B7imHHl

.... 0 .25 7 87t~

.1.00 7..8 5.00 1.

10:00 767*'

'5.00. 77.5

. . .20.0Q' 7.14 25.W0 6.75-i 35.00 . 6.5T 45ý10oV 635'

" 55,00 ',3  :*

  • 65.00"6 "

(1) These MAPLHGRS are not lattice.dependent, therefore the valuteshown also correspond tO the limiting valuefor the most. limiting.lattice for utse when handcalculations. are required.

Page 7 of 21

COLRI,-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITSREPORT 2.0 MINIMUM CRITICAL POWERRATIO (MCPR)

21 Limits for Technical Specification 3,1.7.c During power operation, the operating MCPR shall be greater.than or equal totheo Operating Limit MCPR determined as the maximum of either:

A) ithe appropriate MCPR" firom Figure (2a thru 2d) t 2 '"5 times the K(MY shown in Figure 2e, or, B) the appropriate MCPR(P)(4 ) from Figure 2f.

AdditionalMCPR(P) limits are requiired forioperations without a backup pressure regulator.

These :limjts are shown in Figure 2g.

,2,2 Limits for Technical: Specification 3.I.7.e, Durinig 3 loop operationi the Op'erating Limit MCPR shall be. increaseidby 0.02., No adjustment is needed during 4-loop operation.

NOTES:.

I Based.on a 107MCPRSafety LiRiit(SLCPR) 2 For Figures 2athru'2dtau (r) defined as tbllows:

,A 0.868 seconds, control rod average:scram insertion time limit to notch 39

  1. B =.672-0.65x N /lNy ] x.*0*6 rh*, :.. Njr./j .Ni n = number of surveillaicetests performed in cycle Ni =number of-active,coýntiol'trds measured in the.i surveillance test

= average scramtime to notclh39 of all rods: measured in the,i surveillane rtest N, =,total number of active rods measured 3 .For the current exposure and feedwiltdr-pump configuration. "Pump Coribinatioinaare alS6 described in operating procedure N I-OP-, 16, attachment 13 4 introduction of thezNF2 fuel type requires use o fpower dependent- MCPR limits for all off-rated, conditions, ifncludirig peratiofiswith6ut iabadkup pressure regulator. When power is greater than.45%, tbe k(P) multiplicr from Figure 2f is applied to the applicable rated condition MCPR'limits from Figures'2a thru 2d. At less than or equal-to 45%,power, tie MC PR(P)limits in Figure :2 *ar applied directlyi.This discussion also'applies to Figure:

2g. Figure 2fand 2g are,applicableto(b,bothGEl I anrd'GNF2 fuiel.

$.:,Option:BOILMCPR limits for GEl ,in Figurcs 2a-2c:are set bythe Detectiand Suppress(Sabji.lity).Evaluation for Reload 21.

Page 8 of 21

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT Figure 2a MCPR Operating Limits for Feedwater Pump Combination 1 maximum flows Beginning Of Cycle to EOR*.1448 MWd/ST (Bounds TDFWP+MDFWP, TDFWP only, MDFWP only,, two MDFWPs) 1.61;

,1.59 0(, 1.59) 1.57 0z C.,

GNF2

.2 1, .55 a.

0.

'E 1.53 C.)

E 1.51 (1, 1.51)*

GEll 1 7A9

  • (0, 1.49)

(0, 1A7 11.47 4 4 4 4 4.

0 0.2 0.4 0.6 0,8 I Tau

  • EORlis the end of rated.exposure as defined in the CycleManagement Report Page ,of-21

COLRI -20 NINE MILE POINT UNIT I RevisionO0 CORE OPERATING LIMITS REPORT Figure.2b MCPR Operating Limits for Feedwater Pump Combination Imaximum flows EOR*.1448 MWd/ST to End Of Cycle (Bounds TOFWP+MDFWP, TDFWP only, MDFWP only, two MDFWPs) 1:.69 1.67 (1, 1.67) 1.65 1:63 t .59 1,61 41bb

_6 0

o 1 *57 1.655 (1',1.54) 1,53 1.47 1.45 0 0.2 0.4 0.6 0.8 Thu

  • EOR is the'end of rated exposure as'defined inthe Cycle Management Report Page 10 of21

COLR1-20 NINE MILE POINT UNIT 1 Revision .0 CORE OPERATING LIMITS REPORT Figure.2c MCPROperating Limits for Feedwater Pump Combination 2 maximumn flows Beginning of Cycle to EOR*'1448 MWd/ST

.(Bunds TDFWP+ two MDFWPs) 1.65 1.63 (1, 1:63) 1.59 LCO1.55 (1, 1.55)

.2 1,51 1.49 S1.47 1.45 0 0,2 04 0.6 0'8:

Tau

  • EOR is the end of rabted exposure as idefined in the-Cycle ManagemientReport

,Page, 1 of 21

COLRI-20 NINE. MILE POINT UNIT I Revision0 CORE OPERATING LIMITS REPORT Figure 2d MCPR Operating Limits for Feedwater Pump Combination 2 maximum flows EOR*-1448 MWdlST to End Of Cycle (Bounds TDFWP+ two MDFWPs) 1.73 1.71 1.69 GNF2 1.67 1.65 1.63 S163 1.61 o 1.59 (0E.1 I (*1.,:1..56):

-1.57

E 1.57
  • S :1.55 ig 1:53 1;51 1.49 1.47 (0,*1.471) 1.45 0 0.2 0.4 ;0.6 0.8 I Tau.
  • EOR is the end of rated exposure as defined in:the Cycle.-Management Report Page.12:of21

NINE MILE POINT UNIT'i COLR1-20 Revision 0 CORE OPERATING: LIMITS REPORT Figure 2e NMP-1 K(f) Curve for MCPR 1.5 KM)= 1.50 when 45% > Flow, Otherwise.:

- 105.0/%KU) = MAX(1.0, 1.37 - .441i Flow 11.00,%)

I

- 107,0% K(U)= MAX( 1.0,. 1.35280- 0.441 Flow/i 100%)

-112.0% K(f)= MAX( 1.0,1.37926'- 0:441 -Flow/ 100%)

1.4. Si-,7.0 0%K(f =MMA(, 1,.0,1.40352 -04.4,1 *Flowto100%.)*

- Automatic K(t).= MAX(: 1.0, 1.441 - 0,441 Flow / 100%)

1.3 f-AutomaticFlow Control.

a-0 117% Scoop Tube Setting

... I.

1.2:1 -- ...... ...............----- --

112% Scoop Tube:Setting 1.1]

107%:Sc0op Tube Setting 1

1,02.5% Scoop Tube Setting 0.9 0 20 40, 60 80: 100 120 Core Flow (% of Rated)

Page 13of21

COLRI-20 NINE. MILE POINT UNIT 1 Revision 0 CORE OPERATING LIMITS REPORT Figure 2f MCpR(P) Limits for Normal Operation 5

For, 25%

  • P
  • 45%

'wMCPI R(P) = [285+).026(4'5%-P)] for Core Flow>

60%,Flow

'MCPR(P) = [2.35+0D048(45%-P)] for Core Flow, 60% Flow

.MCPR(P) =.K(P)

  • theappropriate MCPR.Umit from Figures 2a through 2dfor 45% .5,Ps 1.00%
  • K(P)= [1,.21 6+0.0665(65%-P) fort45% : P ý65%

° K(P),=[1.133.+0.00415(85%-P)] for65% s5P 85%

°K(P)= [.!000+0100887(100%-P)J for 85% !;P S 100%

Core Flow." > 60%

3 E0.

it Core Flow *60%

2 1i 11 0~~ ----

6 .n 40 60 80 *100 Core Thermal Power (P):in units of %"Rated Thermal Power (%RTP)

Page 14:of21

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT Figure 2g MCPR(P) Limits for Operation Without Backup Pressure Regulator 5

ft I I For 25%'=P <-45%

"MCPR(P) f2.85+0.026(45%-P)] for Core Flow > 60% Flow

  • :MCpR(P) =2.35+s-0,048(45%-P)] for. Cre Flow !,60% Flow MCPR(P) = K(P) the"appopriate MCPR iUmit from Figurpe 2a through 2dfor 45%'sP s 100%
  • 'K(P) =[i:.336+0:O1085(65%-P)]for 45% 2; P s 65%

4 +

  • K(P) = [1 1'98+0.00690(85%-P)] j< !or 5J . ; P 85%
  • K(P) =.[1.00040.O.00887(10.0%-Pfl for 85%1/

    .60%

E-C.) Core Flow !:60%

E7 2

1*

0 0 ý20 40 160 80 '100.

CoreThermal Power (P) in units of% Rated Thermal Power (%RTP)

Page 15 of 21

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT 3.0 LINEARTHEAT GENERATION RATE (LHGR) 3.1 Limits for Technical Specification 3.1.7.b During-power operation, the Linear Heat Generation Rate (LHGR) of any rod in any fuel assembly at any axial.location shall not exceed the maximum of I IA,0kW/ftO or the limiting yalues shown in'RSLD-21, Revision 0, ';Nine Mile Point Unit I'Reload 21, ReloadSpecific Lattice Data". This document cofitains-the LHGR limits for both U02 rods (which contain noggadolinium) and,"the most'limiting gadolini umbearing rods, Other gadoliniumwbearing rods have LHGR limits which lie betwieenthese two curves. Compliance.,.with these'limits will be monitored by the plant's process computer.

For power operations'betWeen 45% and 100% RTP(2) withoutva 3 backup pressuirei.

MFLPDOshall, be < LHGRFAC(P)( .I regulatori operating NOTE:

i PLHGR shall be maintained below I l.OkW/ft during plant:operating t assure the PCT remains below 1500 . under'steam co6ling iriitigation strategies :specifiedin the.EOPs.

2 Introduction of the GNF2 fuel type requires use of a power dependent LHGR Correction.Factor, or.

LHGRUAC(P) for power operations without a backup pressure regulatorUat greater than or equal to 43% RIT. Below 45% RTP, no additional limits arc required;. Figure'3 is aplIlicableto both GEl and GNF2 fuel types.

3 LHIGRFAC(p) limits are provided forroptionzB and option A scram times: If scram times are slower than option B9 (i.e. t 5 0),then opti6n A limits must be applied; Page 1.6 of 21

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT Figure 3 LHGRFAC(P) Limits for Operation Without Backup Pressure Regulator 1.2 1.0 0.8 0.J 0.4 0.2 0.0 45 50 55 60 65 70 75 80 85 90 95 100 Core Thermal Power (P) In units of % Rated Thermal Power (%RTP)

Page 17 of 21

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT 4.0 POWER/FLOW RELATIONSHIP DURING OPERATION 4.1 Limits for Technical Specification 3.1.7.d and e The power/flow relationship shall not exceed the limiting values shown in Figure 4.

Page 18 of 21

COLRI-20 NINE MILE POINT UNIT 1 Revision 0 CORE OPERATING LIMITS REPORT Figure 4 Limiting Power / Flow Line 120.00 100.00 80.00 0

60.00 I,-

0.

40.00 00 20.00 0.00 0 20 40 60 80 100 120 Core Flow (% of Rated)

Page 19 of 21

COLR1 -20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT 5.0 REFERENCE FOR TECHNICAL SPECIFICATIONS Technical Specification 6.6.5b:

NEDE 24011 -P-A- 17, "General Electric Standard Application for Reactor Fuel,"

September 2010 and the U.S. Supplement, NEDE-2401 I-P-A- 17-US, September 2010.

Page 20 of 21

COLRI-20 NINE MILE POINT UNIT I Revision 0 CORE OPERATING LIMITS REPORT 6.0 SOURCE DOCUMENTS The Core Operating Limits contained in this report were obtained from the following documents:

CORE OPERATING LIMITS REFERENCES APLHGR Limits (Section 1) 0000-0108-3371-SRLR, Revision 0, February Table 1 2011, Supplemental Reload Licensing Report for Nine Mile Point 1, Reload 21, Cycle 20 and corresponding 3 and 4 loop multipliers MEF-NMP-EA11-049, Transmittal of Exposure-dependent GEl I and GNF2 Fuel MAPLHGR Limits for Cycle 22, April 15, 2011 Lattice Descriptions 0000-0108-3371-FBIR, Revison 0, February 2011 Fuel Bundle Information Report for Nine Mile Point 1, Reload 21, Cycle 20 MCPR Limits (Section 2) 0000-0108-3371-SRLR, Revision 0, February 2011, Supplemental Reload Licensing Report for Nine Mile Point 1, Reload 21, Cycle 20 0000-0130-4605-R1, Nine Mile Point 1 Cycle 22 Revised Operated Power Dependent Limits Below Pbypass with Turbine Bypass, April 5, 2011 0000-0131-9552-RO, Nine Mile Point 1 Cycle 22 GNF2 NFI PROOS Off-rated Limits with Option B Scram, April 12, 2011 EOR Definition NMP1CMR, Revision 20, Nine Mile Point Unit 1, Cycle 20, Cycle Management Report, April 2011 LHGR Limits (Section 3) 0000-0108-3371-FBIR, Revison 0, February 2011 Fuel Bundle Information Report for Nine Mile Point 1, Reload 21, Cycle 20 0000-0108-3371 -SRLR, Revision 0, February 2011, Supplemental Reload Licensing Report for Nine Mile Point 1, Reload 21, Cycle 20 0000-0131-9552-RO, Nine Mile Point 1 Cycle 22 GNF2 NFI PROOS Off-rated Limits with Option B Scram, April 12, 2011 Power/Flow Relationship (Section 4) NMP1 Technical Specification Amendment 92, Figure 3.1.7.a Page 21 of 21

Retrieved from "https://kanterella.com/w/index.php?title=ML111250544&oldid=2550612"