ML092810562: Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(Created page by program invented by StriderTol)
Line 28: Line 28:
K/A Rating(s):
K/A Rating(s):
001 Control Rod Drive System. A3.05, Ability to monitor automatic operation of the CRDS, including: Individual vs. group rod position.
001 Control Rod Drive System. A3.05, Ability to monitor automatic operation of the CRDS, including: Individual vs. group rod position.
[3.5/3.5] (CFR: 41.7/45.13)
[3.5/3.5] (CFR: 41.7/45.13)
Task Standard: Withdrawal of shutdown banks is initiated starting with Shutdown Bank A.
Task Standard: Withdrawal of shutdown banks is initiated starting with Shutdown Bank A.
Preferred Evaluation Location:    Preferred Evaluation  Method:
Preferred Evaluation Location:    Preferred Evaluation  Method:
Line 47: Line 47:
COMMENTS REV. 0 PAGE  3  0F 131 WATTS BAR NUCLEAR PLANT B.1.a  SIMULATOR OPERATOR INSTRUCTIONS:
COMMENTS REV. 0 PAGE  3  0F 131 WATTS BAR NUCLEAR PLANT B.1.a  SIMULATOR OPERATOR INSTRUCTIONS:
: 1. Initialize to IC 311. a. Ensure the following items are displayed on the Director Summary Page:
: 1. Initialize to IC 311. a. Ensure the following items are displayed on the Director Summary Page:
rd19 Shutdown bank a demand counter fails 0  
rd19 Shutdown bank a demand counter fails 0
: b. Load NRC_Exam_Event_Files.evt from the NRC Exam Flash Drive. Event 20 is set when Shutdown Bank A reaches 110 steps. Malfunction rd19 will enter at this event.  
: b. Load NRC_Exam_Event_Files.evt from the NRC Exam Flash Drive. Event 20 is set when Shutdown Bank A reaches 110 steps. Malfunction rd19 will enter at this event.
: c. Place the simulator in RUN momentarily, and reset the High Flux at Shutdown alarm, and then acknowledge all alarms  
: c. Place the simulator in RUN momentarily, and reset the High Flux at Shutdown alarm, and then acknowledge all alarms
: 3. ENSURE 1-NR-92-145 Recorder is selected to Source Range N31 and Intermediate Range N35.
: 3. ENSURE 1-NR-92-145 Recorder is selected to Source Range N31 and Intermediate Range N35.
: 4. Freeze simulator until the applicant indicates understanding of the task and time is allowed for control board familiarization.  
: 4. Freeze simulator until the applicant indicates understanding of the task and time is allowed for control board familiarization.
: 5. After applicant indicates understanding of task, place simulator in run.  
: 5. After applicant indicates understanding of task, place simulator in run.  


Line 63: Line 63:


INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. A unit startup is in progress following a trip from 100% power due to a generator electrical relay malfunction that occurred 6 days ago.  
: 1. A unit startup is in progress following a trip from 100% power due to a generator electrical relay malfunction that occurred 6 days ago.
: 2. Per the Nuclear Operating Book (NOB), Sheet 7 BANK OVERLAP AND ROD INSERTION LIMITS, the shutdown banks fully withdrawn position is 230 steps.  
: 2. Per the Nuclear Operating Book (NOB), Sheet 7 BANK OVERLAP AND ROD INSERTION LIMITS, the shutdown banks fully withdrawn position is 230 steps.
: 3. GO-2, "Reactor Startup," Section 3.2 "Actions Performed Before Startup," is complete to Step [13.10], WITHDRAW Shutdown Rods to fully withdrawn per SOI-85.01.  
: 3. GO-2, "Reactor Startup," Section 3.2 "Actions Performed Before Startup," is complete to Step [13.10], WITHDRAW Shutdown Rods to fully withdrawn per SOI-85.01.
: 4. The US/SRO has approved shutdown bank withdrawal.  
: 4. The US/SRO has approved shutdown bank withdrawal.
: 5. SOI-85.01, "Control Rod Drive and Indication System," is being performed and is complete to through Section 5.4, Step 5.  
: 5. SOI-85.01, "Control Rod Drive and Indication System," is being performed and is complete to through Section 5.4, Step 5.
: 6. All reactivity briefs required by SPP-10.4, "Reactivity Management Program" have been completed.
: 6. All reactivity briefs required by SPP-10.4, "Reactivity Management Program" have been completed.
INITIATING CUES:
INITIATING CUES:
: 1. You are to continue the performance of SOI-85.01 at Section 5.4 Step 6, and withdraw the shutdown banks.  
: 1. You are to continue the performance of SOI-85.01 at Section 5.4 Step 6, and withdraw the shutdown banks.
: 2. Notify the SRO when the shutdown banks are fully withdrawn.  
: 2. Notify the SRO when the shutdown banks are fully withdrawn.  


Line 176: Line 176:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. A unit startup is in progress following a trip from 100% power due to a generator electrical relay malfunction that occurred 6 days ago.  
: 1. A unit startup is in progress following a trip from 100% power due to a generator electrical relay malfunction that occurred 6 days ago.
: 2. Per the Nuclear Operating Book (NOB), Sheet 7 BANK OVERLAP AND ROD INSERTION LIMITS, the shutdown banks fully withdrawn position is 230 steps.  
: 2. Per the Nuclear Operating Book (NOB), Sheet 7 BANK OVERLAP AND ROD INSERTION LIMITS, the shutdown banks fully withdrawn position is 230 steps.
: 3. GO-2, "Reactor Startup," Section 3.2 "Actions Performed Before Startup," is complete to Step [13.10], WITHDRAW Shutdown Rods to fully withdrawn per SOI-85.01.  
: 3. GO-2, "Reactor Startup," Section 3.2 "Actions Performed Before Startup," is complete to Step [13.10], WITHDRAW Shutdown Rods to fully withdrawn per SOI-85.01.
: 4. The US/SRO has approved shutdown bank withdrawal.  
: 4. The US/SRO has approved shutdown bank withdrawal.
: 5. SOI-85.01, "Control Rod Drive and Indication System," is being performed and is complete to through Section 5.4, Step 5.  
: 5. SOI-85.01, "Control Rod Drive and Indication System," is being performed and is complete to through Section 5.4, Step 5.
: 6. All reactivity briefs required by SPP-10.4, "Reactivity Management Program" have been completed.
: 6. All reactivity briefs required by SPP-10.4, "Reactivity Management Program" have been completed.
INITIATING CUES:
INITIATING CUES:
: 1. You are to continue the performance of SOI-85.01 at Section 5.4 Step 6, and withdraw the shutdown banks.  
: 1. You are to continue the performance of SOI-85.01 at Section 5.4 Step 6, and withdraw the shutdown banks.
: 2. Notify the SRO when the shutdown banks are fully withdrawn.  
: 2. Notify the SRO when the shutdown banks are fully withdrawn.  


Line 212: Line 212:


COMMENTS REV. 0 PAGE  11  0F 10  WATTS BAR NUCLEAR PLANT B.1.b REV. 0 PAGE  12  0F 10  WATTS BAR NUCLEAR PLANT B.1.b  SIMULATOR OPERATOR INSTRUCTIONS:
COMMENTS REV. 0 PAGE  11  0F 10  WATTS BAR NUCLEAR PLANT B.1.b REV. 0 PAGE  12  0F 10  WATTS BAR NUCLEAR PLANT B.1.b  SIMULATOR OPERATOR INSTRUCTIONS:
: 1. Initialize to IC 312. a. Ensure following letdown and charging isolation valves are closed.  
: 1. Initialize to IC 312. a. Ensure following letdown and charging isolation valves are closed.
: a. 1-FCV-62-72.  
: a. 1-FCV-62-72.
: b. 1-FCV-62-73.  
: b. 1-FCV-62-73.
: c. 1-FCV-62-74.  
: c. 1-FCV-62-74.
: d. 1-FCV-62-76.  
: d. 1-FCV-62-76.
: e. 1-FCV-62-69.  
: e. 1-FCV-62-69.
: f. 1-FCV-62-70.  
: f. 1-FCV-62-70.
: g. 1-FCV-62-85.  
: g. 1-FCV-62-85.
: h. 1-FCV-62-86.  
: h. 1-FCV-62-86.
: i. 1-FCV-62-90.  
: i. 1-FCV-62-90.
: j. 1-FCV-62-91.  
: j. 1-FCV-62-91.
: b. Ensure 1-FCV-62-93 is in manual and seal flow is stable at approximately 8 gpm per RCP seal.
: b. Ensure 1-FCV-62-93 is in manual and seal flow is stable at approximately 8 gpm per RCP seal.
: c. Ensure pressurizer level is approximately 66% and rising slowly.
: c. Ensure pressurizer level is approximately 66% and rising slowly.
: 2. Acknowledge all alarms.  
: 2. Acknowledge all alarms.
: 3. Place simulator in FREEZE until the applicant indicates an understanding of the task.  
: 3. Place simulator in FREEZE until the applicant indicates an understanding of the task.
: 4. After applicant indicates understanding of the task, place simulator to RUN.
: 4. After applicant indicates understanding of the task, place simulator to RUN.
Tools/Equipment/Procedures Needed:
Tools/Equipment/Procedures Needed:
Line 238: Line 238:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. The Unit is operating at 100% power.  
: 1. The Unit is operating at 100% power.
: 2. A small leak has been found on the normal letdown path.  
: 2. A small leak has been found on the normal letdown path.
: 3. Letdown and Charging have been isolated per AOI-6, "Small Reactor Coolant System Leak."  
: 3. Letdown and Charging have been isolated per AOI-6, "Small Reactor Coolant System Leak."
: 4. The RADPRO Supervisor has been informed of the intent to establish Excess Letdown. 5. You are the Operator at the Controls.  
: 4. The RADPRO Supervisor has been informed of the intent to establish Excess Letdown. 5. You are the Operator at the Controls.  


INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor has directed you to establish excess letdown to the VCT per AOI-6, "Small Reactor Coolant System Leak." Section 3.0, and Step 15, RESPONSE NOT OBTAINED.  
: 1. The Unit Supervisor has directed you to establish excess letdown to the VCT per AOI-6, "Small Reactor Coolant System Leak." Section 3.0, and Step 15, RESPONSE NOT OBTAINED.
: 2. You are to notify the Unit Supervisor when excess letdown has been aligned and pressurizer level is under control.  
: 2. You are to notify the Unit Supervisor when excess letdown has been aligned and pressurizer level is under control.  


Line 369: Line 369:


task. INITIAL CONDITIONS:
task. INITIAL CONDITIONS:
: 1. The Unit is operating at 100% power.  
: 1. The Unit is operating at 100% power.
: 2. A small leak has been found on the normal letdown path.  
: 2. A small leak has been found on the normal letdown path.
: 3. Letdown and Charging have been isolated per AOI-6, "Small Reactor Coolant System Leak."  
: 3. Letdown and Charging have been isolated per AOI-6, "Small Reactor Coolant System Leak."
: 4. The RADPRO Supervisor has been informed of the intent to establish Excess Letdown. 5. You are the Operator at the Controls.  
: 4. The RADPRO Supervisor has been informed of the intent to establish Excess Letdown. 5. You are the Operator at the Controls.  


INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor has directed you to establish excess letdown to the VCT per AOI-6, "Small Reactor Coolant System Leak." Section 3.0, and Step 15, RESPONSE NOT OBTAINED.  
: 1. The Unit Supervisor has directed you to establish excess letdown to the VCT per AOI-6, "Small Reactor Coolant System Leak." Section 3.0, and Step 15, RESPONSE NOT OBTAINED.
: 2. You are to notify the Unit Supervisor when excess letdown has been aligned and pressurizer level is under control.  
: 2. You are to notify the Unit Supervisor when excess letdown has been aligned and pressurizer level is under control.  


Line 405: Line 405:
COMMENTS REV. 0 PAGE 21 OF 131 WATTS BAR NUCLEAR PLANT B.1.c REV. 0 PAGE 22 OF 131 WATTS BAR NUCLEAR PLANT B.1.c  SIMULATOR OPERATOR INSTRUCTIONS:
COMMENTS REV. 0 PAGE 21 OF 131 WATTS BAR NUCLEAR PLANT B.1.c REV. 0 PAGE 22 OF 131 WATTS BAR NUCLEAR PLANT B.1.c  SIMULATOR OPERATOR INSTRUCTIONS:
: 1. Initialize to IC 313. a. Ensure the following items are displayed on the Director Summary Page:
: 1. Initialize to IC 313. a. Ensure the following items are displayed on the Director Summary Page:
th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity hs-63-67a hs-63-67a sis accumulator tank 4 flow isolation valve Open  
th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity hs-63-67a hs-63-67a sis accumulator tank 4 flow isolation valve Open
: b. Ensure that the following remote is set as indicated on the Director Remote Page. sir01 pwr to cold leg accumu isolation valves fcv-63-67, 80, 98, 119 on  
: b. Ensure that the following remote is set as indicated on the Director Remote Page. sir01 pwr to cold leg accumu isolation valves fcv-63-67, 80, 98, 119 on
: c. Place the simulator in RUN momentarily, and acknowledge all alarms.  
: c. Place the simulator in RUN momentarily, and acknowledge all alarms.
: 4. Place simulator in FREEZE until the Applicant indicates an understanding of the task.  
: 4. Place simulator in FREEZE until the Applicant indicates an understanding of the task.
: 3. After Applicant indicates understanding of the task, place simulator to RUN.
: 3. After Applicant indicates understanding of the task, place simulator to RUN.
Tools/Equipment/Procedures Needed:
Tools/Equipment/Procedures Needed:
Line 420: Line 420:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. A large break LOCA has occurred.  
: 1. A large break LOCA has occurred.
: 2. E-1,"Loss of Reactor or Secondary C oolant,"performance has just been resumed after performance of ES-1.3,"Tra nsfer to Containment Sump."  
: 2. E-1,"Loss of Reactor or Secondary C oolant,"performance has just been resumed after performance of ES-1.3,"Tra nsfer to Containment Sump."
: 3. You are the Control Room Operator.
: 3. You are the Control Room Operator.
INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor directs you perf orm E-1,"Loss of Reactor or Secondary Coolant," Step 26, DETERM INE if cold leg accumulato rs should be isolated.  
: 1. The Unit Supervisor directs you perf orm E-1,"Loss of Reactor or Secondary Coolant," Step 26, DETERM INE if cold leg accumulato rs should be isolated.
: 2. You are to notify the Unit Supervisor when you have completed Step 26.  
: 2. You are to notify the Unit Supervisor when you have completed Step 26.  


Line 535: Line 535:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. A large break LOCA has occurred.  
: 1. A large break LOCA has occurred.
: 2. E-1,"Loss of Reactor or Secondary C oolant,"performance has just been resumed after performance of ES-1.3,"Tra nsfer to Containment Sump."  
: 2. E-1,"Loss of Reactor or Secondary C oolant,"performance has just been resumed after performance of ES-1.3,"Tra nsfer to Containment Sump."
: 3. You are the Control Room Operator.
: 3. You are the Control Room Operator.
INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor directs you perf orm E-1,"Loss of Reactor or Secondary Coolant," Step 26, DETERM INE if cold leg accumulato rs should be isolated.  
: 1. The Unit Supervisor directs you perf orm E-1,"Loss of Reactor or Secondary Coolant," Step 26, DETERM INE if cold leg accumulato rs should be isolated.
: 2. You are to notify the Unit Supervisor when you have completed Step 26.  
: 2. You are to notify the Unit Supervisor when you have completed Step 26.  


Line 568: Line 568:
COMMENTS REV. 6  PAGE 32 OF 131 WATTS BAR NUCLEAR PLANT B.1.d REV. 6  PAGE 33 OF 131 WATTS BAR NUCLEAR PLANT B.1.d  SIMULATOR OPERATOR INSTRUCTIONS:
COMMENTS REV. 6  PAGE 32 OF 131 WATTS BAR NUCLEAR PLANT B.1.d REV. 6  PAGE 33 OF 131 WATTS BAR NUCLEAR PLANT B.1.d  SIMULATOR OPERATOR INSTRUCTIONS:
: 1. Initialize to IC 314. a. Ensure the following items are displayed on the Director Summary Page:
: 1. Initialize to IC 314. a. Ensure the following items are displayed on the Director Summary Page:
th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity ch01a containment pressure transmitter failure pdt-3-42 14 ch01b containment pressure transmitter failure pdt-3-43 14 ch01c containment pressure transmitter failure pdt-3-44 14 ch01d containment pressure transmitter failure pdt-3-45 14 ei-72-12a 07020 cntmt spray pmp b amps 35 fi-72-13 07010 cntmt spray pmp b flow 3000 hs-72-10a-3 06010 cntmt spray pump b mtr sw(red) on hs-72-10a-1 06010 cntmt spray pump b mtr sw(green) off hs-72-27a-1 06020 cntmt spray pump a mtr sw(green) off pdi-30-42 03160 cntmt press diff indicator 12 pdi-30-43 03170 cntmt press diff indicator 12 pdi-30-44 03180 cntmt press diff indicator 12 pdi-30-45 03190 cntmt press diff indicator 12 pdr-30-133-1 03150 cntmt annulus dp indicator 0.5 hs-72-10a hs-72-10a containment spray pump b mtr sw ptlock hs-63-94a Hs-63-94a rhr to rcs cl1_4 flow control valve s open  
th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity ch01a containment pressure transmitter failure pdt-3-42 14 ch01b containment pressure transmitter failure pdt-3-43 14 ch01c containment pressure transmitter failure pdt-3-44 14 ch01d containment pressure transmitter failure pdt-3-45 14 ei-72-12a 07020 cntmt spray pmp b amps 35 fi-72-13 07010 cntmt spray pmp b flow 3000 hs-72-10a-3 06010 cntmt spray pump b mtr sw(red) on hs-72-10a-1 06010 cntmt spray pump b mtr sw(green) off hs-72-27a-1 06020 cntmt spray pump a mtr sw(green) off pdi-30-42 03160 cntmt press diff indicator 12 pdi-30-43 03170 cntmt press diff indicator 12 pdi-30-44 03180 cntmt press diff indicator 12 pdi-30-45 03190 cntmt press diff indicator 12 pdr-30-133-1 03150 cntmt annulus dp indicator 0.5 hs-72-10a hs-72-10a containment spray pump b mtr sw ptlock hs-63-94a Hs-63-94a rhr to rcs cl1_4 flow control valve s open
: b. Place the simulator in RUN momentarily, and acknowledge all alarms.  
: b. Place the simulator in RUN momentarily, and acknowledge all alarms.
: 2. Place Hold Order on 1A CS Pump - handswitch is in PULL-TO-LOCK position  
: 2. Place Hold Order on 1A CS Pump - handswitch is in PULL-TO-LOCK position
: 3. Place simulator in FREEZE until the applicant indicates an understanding of the task.  
: 3. Place simulator in FREEZE until the applicant indicates an understanding of the task.
: 4. After applicant indicates understanding of the task, place simulator to RUN.
: 4. After applicant indicates understanding of the task, place simulator to RUN.
Tools/Equipment/Procedures Needed:
Tools/Equipment/Procedures Needed:
Line 583: Line 583:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. 1A-A Containment Spray Pump has been tagged out of service.
: 1. 1A-A Containment Spray Pump has been tagged out of service.
: 2. The unit was at 100% when a Large Break LOCA occurred.  
: 2. The unit was at 100% when a Large Break LOCA occurred.
: 3. 1B-B Containment Spray Pump started and has been spraying containment.  
: 3. 1B-B Containment Spray Pump started and has been spraying containment.
: 4. The break occurred an hour and 10 minutes ago.  
: 4. The break occurred an hour and 10 minutes ago.
: 5. All ECCS equipment is performing it s design functions and is on Containment Sump Recirc.  
: 5. All ECCS equipment is performing it s design functions and is on Containment Sump Recirc.
: 6. You are the Operator at the Controls (OAC).
: 6. You are the Operator at the Controls (OAC).
INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor directs you to perform FR-Z.1, "HIGH CONTAINMENT PRESSURE," Step 10, DETERMINE if RHR spray should be placed in service.  
: 1. The Unit Supervisor directs you to perform FR-Z.1, "HIGH CONTAINMENT PRESSURE," Step 10, DETERMINE if RHR spray should be placed in service.
: 2. You are to notify the Unit Supervisor when you have completed Step 10.  
: 2. You are to notify the Unit Supervisor when you have completed Step 10.  


Line 612: Line 612:
* At least one charging pump and one SI pump running  
* At least one charging pump and one SI pump running  


STANDARD: 1. Applicant has determined that an hour has lapsed since  the beginning of the accident.  [Given in initial conditions]  
STANDARD: 1. Applicant has determined that an hour has lapsed since  the beginning of the accident.  [Given in initial conditions]
: 2. Cntmt press has been checked > 9.5 psig.  
: 2. Cntmt press has been checked > 9.5 psig.
: 3. FCV-63-72 and FCV-63-73 verified to be open by red indicating lights. 4. 1 CCP & 1 SIP verified to be running by indicating lights or amps.
: 3. FCV-63-72 and FCV-63-73 verified to be open by red indicating lights. 4. 1 CCP & 1 SIP verified to be running by indicating lights or amps.
COMMENTS:   
COMMENTS:   
Line 677: Line 677:
___ SAT  
___ SAT  


___ UNSAT STEP 9: [STEP 10b RNO]  
___ UNSAT STEP 9: [STEP 10b RNO]
: 4) OPEN RHR spray 1-FCV-72-40.  
: 4) OPEN RHR spray 1-FCV-72-40.  


Line 705: Line 705:


task. INITIAL CONDITIONS:
task. INITIAL CONDITIONS:
: 1. 1A-A Containment Spray Pump has been tagged out of service.
: 1. 1A-A Containment Spray Pump has been tagged out of service.
: 2. The unit was at 100% when a Large Break LOCA occurred.  
: 2. The unit was at 100% when a Large Break LOCA occurred.
: 3. 1B-B Containment Spray Pump started and has been spraying containment.  
: 3. 1B-B Containment Spray Pump started and has been spraying containment.
: 4. The break occurred an hour and 10 minutes ago.  
: 4. The break occurred an hour and 10 minutes ago.
: 5. All ECCS equipment is performing it s design functions and is on Containment Sump Recirc.  
: 5. All ECCS equipment is performing it s design functions and is on Containment Sump Recirc.
: 6. You are the Operator at the Controls (OAC).
: 6. You are the Operator at the Controls (OAC).
INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor directs you to perform FR-Z.1, "HIGH CONTAINMENT PRESSURE", Step 10, DETERMINE if RHR spray should be placed in service.  
: 1. The Unit Supervisor directs you to perform FR-Z.1, "HIGH CONTAINMENT PRESSURE", Step 10, DETERMINE if RHR spray should be placed in service.
: 2. You are to notify the Unit Supervisor when you have completed Step 10.  
: 2. You are to notify the Unit Supervisor when you have completed Step 10.  


Line 742: Line 742:
COMMENTS REV. 0 Page 42 of 131 WATTS BAR NUCLEAR PLANT B.1.e REV. 0 Page 43 of 131 WATTS BAR NUCLEAR PLANT B.1.e  SIMULATOR OPERATOR INSTRUCTIONS:
COMMENTS REV. 0 Page 42 of 131 WATTS BAR NUCLEAR PLANT B.1.e REV. 0 Page 43 of 131 WATTS BAR NUCLEAR PLANT B.1.e  SIMULATOR OPERATOR INSTRUCTIONS:
: 1. Initialize to IC 315. a. Ensure the following items are displayed on the Director Summary Page:
: 1. Initialize to IC 315. a. Ensure the following items are displayed on the Director Summary Page:
th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity mux_03c123 125-a cntmt hi-hi press steamline isol on pi-30-310 03110 containment pressure 3.5 pi-30-311 03120 containment pressure 3.5 h2i-43-200 03060 loca h2 cntmt monitor 3.5 h2i-43-210 03070 loca h2 cntmt monitor 3.5 pdi-30-42 03160 cntmt press diff indicator 4 pdi-30-43 03170 cntmt press diff indicator 4 pdi-30-44 03180 cntmt press diff indicator 4 pdi-30-45 03190 cntmt press diff indicator 4  
th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity mux_03c123 125-a cntmt hi-hi press steamline isol on pi-30-310 03110 containment pressure 3.5 pi-30-311 03120 containment pressure 3.5 h2i-43-200 03060 loca h2 cntmt monitor 3.5 h2i-43-210 03070 loca h2 cntmt monitor 3.5 pdi-30-42 03160 cntmt press diff indicator 4 pdi-30-43 03170 cntmt press diff indicator 4 pdi-30-44 03180 cntmt press diff indicator 4 pdi-30-45 03190 cntmt press diff indicator 4
: b. Place the simulator in RUN momentarily, and acknowledge all alarms.  
: b. Place the simulator in RUN momentarily, and acknowledge all alarms.
: 2. Place simulator in FREEZE until the applicant indicates an understanding of the task.  
: 2. Place simulator in FREEZE until the applicant indicates an understanding of the task.
: 3. After applicant indicates understanding of the task, place simulator to RUN.
: 3. After applicant indicates understanding of the task, place simulator to RUN.
Tools/Equipment/Procedures Needed:
Tools/Equipment/Procedures Needed:
Line 756: Line 756:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit has experienced a LOCA.  
: 1. Unit has experienced a LOCA.
: 2. MCR crew is implementing E-1, "Loss of Reactor or Secondary Coolant."  
: 2. MCR crew is implementing E-1, "Loss of Reactor or Secondary Coolant."
: 3. E-1, directs that the hydrogen recombiners be placed in service using SOI-83.01, "Containment Hydrogen Recombiners."  
: 3. E-1, directs that the hydrogen recombiners be placed in service using SOI-83.01, "Containment Hydrogen Recombiners."
: 4. You are the Control Room Operator.
: 4. You are the Control Room Operator.
INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor has directed you to place Hydrogen Recombiner "A" in service, using SOI-83.01, Containment Hydrogen Recombiners."  
: 1. The Unit Supervisor has directed you to place Hydrogen Recombiner "A" in service, using SOI-83.01, Containment Hydrogen Recombiners."
: 2. Notify the Unit Supervisor when the required power setting is reached.  
: 2. Notify the Unit Supervisor when the required power setting is reached.  


Line 830: Line 830:
___ SAT  
___ SAT  


___ UNSAT REV. 0 Page 48 of 131 WATTS BAR NUCLEAR PLANT B.1.e  STEP 8: [7] RECORD CNTMT H2 % on Data Sheet 1, THEN    INDICATE from which source H2 percentage was obtained:  
___ UNSAT REV. 0 Page 48 of 131 WATTS BAR NUCLEAR PLANT B.1.e  STEP 8: [7] RECORD CNTMT H2 % on Data Sheet 1, THEN    INDICATE from which source H2 percentage was obtained:
[7.1] ANAL A CNTMT H2,1-H21-43-200 [1-M-10]  
[7.1] ANAL A CNTMT H2,1-H21-43-200 [1-M-10]  


[7.2] ANAL B CNTMT H2 , 1-H21 210 [1-M-10]  
[7.2] ANAL B CNTMT H2 , 1-H21 210 [1-M-10]  
Line 851: Line 851:
___ UNSAT REV. 0 Page 49 of 131 WATTS BAR NUCLEAR PLANT B.1.e  STEP 10: [9]  RECORD CNTMT PRESS (psig) on Data Sheet 1,  THEN INDICATE which indicator was used:  
___ UNSAT REV. 0 Page 49 of 131 WATTS BAR NUCLEAR PLANT B.1.e  STEP 10: [9]  RECORD CNTMT PRESS (psig) on Data Sheet 1,  THEN INDICATE which indicator was used:  


[9.1] 1-PI-30-310, CNTMT WR PRESS [1-M-9]   
[9.1] 1-PI-30-310, CNTMT WR PRESS [1-M-9]   


[9.2] 1-PI-30-311, CNTMT WR PRESS [1-M-9]  
[9.2] 1-PI-30-311, CNTMT WR PRESS [1-M-9]  


STANDARD:  Applicant enters a value of 3 psig for either pressure indicator.  
STANDARD:  Applicant enters a value of 3 psig for either pressure indicator.  
Line 911: Line 911:
CRITICAL STEP      ___ SAT  
CRITICAL STEP      ___ SAT  


___ UNSAT NOTES 1)  Periodic potentiometer adjustment is necessary to maintain Required Power setting. Temperature is obtained by selecting an average temperature of all operable thermocouples. Temperature should rise to 1150-1400°F in approximately 4 hours  depending on initial containment temperature. 2)  Recombiner temperature should be allowed to stabilize before making power changes  due to the lag time between adjustment and actual temperature change.  
___ UNSAT NOTES 1)  Periodic potentiometer adjustment is necessary to maintain Required Power setting. Temperature is obtained by selecting an average temperature of all operable thermocouples. Temperature should rise to 1150-1400°F in approximately 4 hours  depending on initial containment temperature. 2)  Recombiner temperature should be allowed to stabilize before making power changes  due to the lag time between adjustment and actual temperature change.
: 3)  1 kW power change is approximately equal to 20°F recombiner temperature change.
: 3)  1 kW power change is approximately equal to 20°F recombiner temperature change.
STEP 17: [16]  AFTER recombiner temperature has stabilized for  approximately 30 minutes, THEN ADJUST POWER  ADJUST potentiometer to maintain 1225 - 1400°F recombiner average temperature.  
STEP 17: [16]  AFTER recombiner temperature has stabilized for  approximately 30 minutes, THEN ADJUST POWER  ADJUST potentiometer to maintain 1225 - 1400°F recombiner average temperature.  
Line 936: Line 936:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit has experienced a LOCA.  
: 1. Unit has experienced a LOCA.
: 2. MCR crew is implementing E-1, "Loss of Reactor or Secondary Coolant."  
: 2. MCR crew is implementing E-1, "Loss of Reactor or Secondary Coolant."
: 3. E-1, directs that the hydrogen recombiners be placed in service using SOI-83.01, "Containment Hydrogen Recombiners."  
: 3. E-1, directs that the hydrogen recombiners be placed in service using SOI-83.01, "Containment Hydrogen Recombiners."
: 4. You are the Control Room Operator.
: 4. You are the Control Room Operator.
INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor has directed you to place Hydrogen Recombiner "A" in service, using SOI-83.01, Containment Hydrogen Recombiners."  
: 1. The Unit Supervisor has directed you to place Hydrogen Recombiner "A" in service, using SOI-83.01, Containment Hydrogen Recombiners."
: 2. Notify the Unit Supervisor when the required power setting is reached.  
: 2. Notify the Unit Supervisor when the required power setting is reached.  


Line 951: Line 951:
Alternate Path:
Alternate Path:
N/A Facility JPM #: 3-OT-JPMR060 K/A Rating(s):
N/A Facility JPM #: 3-OT-JPMR060 K/A Rating(s):
064 Emergency Diesel Generators. A1.03 Ability to predict and/or monitor changes in parameters (to prevent exceeding design limits) associated with operating the ED/G system controls including: Operating voltages, currents, and temperatures  
064 Emergency Diesel Generators. A1.03 Ability to predict and/or monitor changes in parameters (to prevent exceeding design limits) associated with operating the ED/G system controls including: Operating voltages, currents, and temperatures
[3.2/3.3] (CFR: 41.5 / 45.5) 064  Emergency Diesel Generators. A4.06 Ability to manually operate and/or monitor in the control room: Manual start, loading, and stopping of the ED/G [3.9/3.9]  
[3.2/3.3] (CFR: 41.5 / 45.5) 064  Emergency Diesel Generators. A4.06 Ability to manually operate and/or monitor in the control room: Manual start, loading, and stopping of the ED/G [3.9/3.9]
(CFR: 41.7 / 45.5 to 45.8)
(CFR: 41.7 / 45.5 to 45.8)
Task Standard: 1B-B Diesel Generator is synchronized to the shutdown board from the MCR, per SOI-82.02 Section 8.1.4, and then loaded to 4 MW and 0.74-1.25 MVARs.
Task Standard: 1B-B Diesel Generator is synchronized to the shutdown board from the MCR, per SOI-82.02 Section 8.1.4, and then loaded to 4 MW and 0.74-1.25 MVARs.
Line 974: Line 974:
COMMENTS REV. 6      PAGE 56 OF 131 WATTS BAR NUCLEAR PLANT B.1.f REV. 6      PAGE 57 OF 131 WATTS BAR NUCLEAR PLANT B.1.f  SIMULATOR OPERATOR INSTRUCTIONS:
COMMENTS REV. 6      PAGE 56 OF 131 WATTS BAR NUCLEAR PLANT B.1.f REV. 6      PAGE 57 OF 131 WATTS BAR NUCLEAR PLANT B.1.f  SIMULATOR OPERATOR INSTRUCTIONS:
: 1. Initialize to IC # 316. NOTE:  If this JPM is to be run concurrently with B.1.b, Place Excess Letdown in service, then reset to IC # 312.
: 1. Initialize to IC # 316. NOTE:  If this JPM is to be run concurrently with B.1.b, Place Excess Letdown in service, then reset to IC # 312.
: 2. 1B-B Diesel Generator is running unloaded, after an idle start.  
: 2. 1B-B Diesel Generator is running unloaded, after an idle start.
: 3. Place the simulator in RUN momentarily, and acknowledge all alarms.  
: 3. Place the simulator in RUN momentarily, and acknowledge all alarms.
: 4. Place simulator in FREEZE until the Applicant indicates an understanding of the task.  
: 4. Place simulator in FREEZE until the Applicant indicates an understanding of the task.
: 5. After applicant indicates understanding of the task, place simulator to RUN.
: 5. After applicant indicates understanding of the task, place simulator to RUN.
Tools/Equipment/Procedures Needed:
Tools/Equipment/Procedures Needed:
Line 988: Line 988:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit is at 100% power.  
: 1. Unit is at 100% power.
: 2. Testing is being conducted on 1B-B diesel generator. It is to be paralleled to the shutdown board for a Factory Representative on site.  
: 2. Testing is being conducted on 1B-B diesel generator. It is to be paralleled to the shutdown board for a Factory Representative on site.
: 3. The 1B-B DG is running at rated speed , after performance of SOI-82.02, "Diesel Generator (D/G) 1B-B," Section 8.1.3 Idle Speed to Rated Speed.  
: 3. The 1B-B DG is running at rated speed , after performance of SOI-82.02, "Diesel Generator (D/G) 1B-B," Section 8.1.3 Idle Speed to Rated Speed.
: 4. You are an extra control room operator on shift.  
: 4. You are an extra control room operator on shift.  


INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor directs you to parallel the 1B-B diesel generator to the 1B-B Shutdown Board per SOI-82.02, "Diesel Generator (D/G) 1B-B" and load it to 4 MWs.
: 1. The Unit Supervisor directs you to parallel the 1B-B diesel generator to the 1B-B Shutdown Board per SOI-82.02, "Diesel Generator (D/G) 1B-B" and load it to 4 MWs.
: 2. SOI-82.02, "Diesel Genera tor (D/G) 1B-B," Section 8.1.4 Steps 1 through 3 have been performed.  
: 2. SOI-82.02, "Diesel Genera tor (D/G) 1B-B," Section 8.1.4 Steps 1 through 3 have been performed.
: 3. You are to inform the Unit Supervisor when the diesel generator is loaded to 4 MWs.
: 3. You are to inform the Unit Supervisor when the diesel generator is loaded to 4 MWs.
REV. 6      PAGE 59 OF 131 WATTS BAR NUCLEAR PLANT B.1.f  START TIME: _______
REV. 6      PAGE 59 OF 131 WATTS BAR NUCLEAR PLANT B.1.f  START TIME: _______
Line 1,085: Line 1,085:


___ UNSAT REV. 6      PAGE 64 OF 131 WATTS BAR NUCLEAR PLANT B.1.f  NOTE DG MEGAVARs may "swing" when the 6.9 KV automatic tap changers engage to stabilize the voltage in the system.
___ UNSAT REV. 6      PAGE 64 OF 131 WATTS BAR NUCLEAR PLANT B.1.f  NOTE DG MEGAVARs may "swing" when the 6.9 KV automatic tap changers engage to stabilize the voltage in the system.
STEP 10: [11.2]  PERFORM the following:  
STEP 10: [11.2]  PERFORM the following:
[b] MAINTAIN DG MEGAVARS 0.75 to 1.25 OUTGOING on 1-EI-82-41A, with 1-HS-82-42, VOLTAGE REGULATOR.
[b] MAINTAIN DG MEGAVARS 0.75 to 1.25 OUTGOING on 1-EI-82-41A, with 1-HS-82-42, VOLTAGE REGULATOR.
STANDARD:  The generator megavars is adjusted to between 0.75 and 1.25 Megavars on 0-EI-82-41A.  
STANDARD:  The generator megavars is adjusted to between 0.75 and 1.25 Megavars on 0-EI-82-41A.  
Line 1,135: Line 1,135:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit is at 100% power.  
: 1. Unit is at 100% power.
: 2. Testing is being conducted on 1B-B diesel generator. It is to be paralleled to the shutdown board for a Factory Rep. on site.  
: 2. Testing is being conducted on 1B-B diesel generator. It is to be paralleled to the shutdown board for a Factory Rep. on site.
: 3. The 1B-B DG is running at rated speed , after performance of SOI-82.02, "Diesel Generator (D/G) 1B-B," Section 8.1.3 Idle Speed to Rated Speed.  
: 3. The 1B-B DG is running at rated speed , after performance of SOI-82.02, "Diesel Generator (D/G) 1B-B," Section 8.1.3 Idle Speed to Rated Speed.
: 4. You are an extra control room operator on shift.  
: 4. You are an extra control room operator on shift.  


INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor directs you to parallel the 1B-B diesel generator to the 1B-B Shutdown Board per SOI-82.02, "Diesel Generator (D/G) 1B-B" and load it to 4 MWs.
: 1. The Unit Supervisor directs you to parallel the 1B-B diesel generator to the 1B-B Shutdown Board per SOI-82.02, "Diesel Generator (D/G) 1B-B" and load it to 4 MWs.
: 2. SOI-82.02, "Diesel Genera tor (D/G) 1B-B," Section 8.1.4 Steps 1 through 3 have been performed.  
: 2. SOI-82.02, "Diesel Genera tor (D/G) 1B-B," Section 8.1.4 Steps 1 through 3 have been performed.
: 3. You are to inform the Unit Supervisor when the diesel generator is loaded to 4 MWs.
: 3. You are to inform the Unit Supervisor when the diesel generator is loaded to 4 MWs.
REV. 2 PAGE 67 OF 131 WATTS BAR NUCLEAR PLANT B.1.g     
REV. 2 PAGE 67 OF 131 WATTS BAR NUCLEAR PLANT B.1.g     
Line 1,167: Line 1,167:
COMMENTS REV. 2 PAGE 69 OF 131 WATTS BAR NUCLEAR PLANT B.1.g  SIMULATOR OPERATOR INSTRUCTIONS:
COMMENTS REV. 2 PAGE 69 OF 131 WATTS BAR NUCLEAR PLANT B.1.g  SIMULATOR OPERATOR INSTRUCTIONS:
: 1. Initialize to IC 317. a. Ensure the following items are displayed on the Director Summary Page:
: 1. Initialize to IC 317. a. Ensure the following items are displayed on the Director Summary Page:
rd02 Uncontrolled rod insertion, bank d, group 2 100% severity  
rd02 Uncontrolled rod insertion, bank d, group 2 100% severity
: b. Ensure the switches on 1-M-13 to the "N42" position to defeat Power Range Channel N42 inputs per AOI-4, Attachment 1, and Step 1 a. through f.  
: b. Ensure the switches on 1-M-13 to the "N42" position to defeat Power Range Channel N42 inputs per AOI-4, Attachment 1, and Step 1 a. through f.
: c. Place the simulator in RUN momentarily, and acknowledge all alarms.  
: c. Place the simulator in RUN momentarily, and acknowledge all alarms.
: 2. Load NRC_Exam_Event_Files.evt from the NRC Exam Flash Drive. The malfunction will be entered when Rod Control Selector Switch is placed in AUTO (Event 23).  
: 2. Load NRC_Exam_Event_Files.evt from the NRC Exam Flash Drive. The malfunction will be entered when Rod Control Selector Switch is placed in AUTO (Event 23).
: 3. Place simulator in FREEZE until the applicant indicates an understanding of the task.  
: 3. Place simulator in FREEZE until the applicant indicates an understanding of the task.
: 4. After Applicant indicates understanding of the task, place simulator to RUN.
: 4. After Applicant indicates understanding of the task, place simulator to RUN.


Line 1,184: Line 1,184:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit 1 is at 100% power.  
: 1. Unit 1 is at 100% power.
: 2. Power Range Monitor N42 failed during last shift.  
: 2. Power Range Monitor N42 failed during last shift.
: 3. AOI-4 "NUCLEAR INSTRUMENTATION MALFUNCTIONS," Section 3.4. "Power Range Monitor (PRM) Failure," has been completed through Step 16.a.  
: 3. AOI-4 "NUCLEAR INSTRUMENTATION MALFUNCTIONS," Section 3.4. "Power Range Monitor (PRM) Failure," has been completed through Step 16.a.
: 4. Work Control has notified the MCR that repairs to PRM N42 are complete and the instrument is ready to be returned to service.  
: 4. Work Control has notified the MCR that repairs to PRM N42 are complete and the instrument is ready to be returned to service.
: 5. You are the Operator at the Controls.  
: 5. You are the Operator at the Controls.  


INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor has directed you to return PRM N42 to service.  
: 1. The Unit Supervisor has directed you to return PRM N42 to service.
: 2. You are to notify the US when the control rods have been returned to AUTO.  
: 2. You are to notify the US when the control rods have been returned to AUTO.  


Line 1,218: Line 1,218:


___ UNSAT REV. 2 PAGE 72 OF 131 WATTS BAR NUCLEAR PLANT B.1.g  NOTE TO EVALUATOR:  The following steps are from Attachment 1 page 2 of 2, AOI-4.
___ UNSAT REV. 2 PAGE 72 OF 131 WATTS BAR NUCLEAR PLANT B.1.g  NOTE TO EVALUATOR:  The following steps are from Attachment 1 page 2 of 2, AOI-4.
STEP 3: [STEP 2]  WHEN PRM is ready for return to service , THEN PERFORM the following steps:  
STEP 3: [STEP 2]  WHEN PRM is ready for return to service , THEN PERFORM the following steps:
: a. PLACE DETECTOR CURRENT COMPARATOR switch for UPPER SECTION in NORMAL STANDARD: Detector Current Comparator Upper Section switch placed to "NORMAL" (Miscellaneous Control & Indication Panel,1-IDWR-92-N50-G IV)
: a. PLACE DETECTOR CURRENT COMPARATOR switch for UPPER SECTION in NORMAL STANDARD: Detector Current Comparator Upper Section switch placed to "NORMAL" (Miscellaneous Control & Indication Panel,1-IDWR-92-N50-G IV)
Step is critical for proper restoration of upper power detector to current comparator.
Step is critical for proper restoration of upper power detector to current comparator.
Line 1,368: Line 1,368:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit 1 is at 100% power.  
: 1. Unit 1 is at 100% power.
: 2. Power Range Monitor N42 failed during last shift.  
: 2. Power Range Monitor N42 failed during last shift.
: 3. AOI-4 "NUCLEAR INSTRUMENTATION MALFUNCTIONS," Section 3.4. "Power Range Monitor (PRM) Failure," has been completed through Step 16.a.  
: 3. AOI-4 "NUCLEAR INSTRUMENTATION MALFUNCTIONS," Section 3.4. "Power Range Monitor (PRM) Failure," has been completed through Step 16.a.
: 4. Work Control has notified the MCR that repairs to PRM N42 are complete and the instrument is ready to be returned to service.  
: 4. Work Control has notified the MCR that repairs to PRM N42 are complete and the instrument is ready to be returned to service.
: 5. You are the Operator at the Controls.
: 5. You are the Operator at the Controls.
INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor has directed you to return PRM N42 to service.  
: 1. The Unit Supervisor has directed you to return PRM N42 to service.
: 2. You are to notify the US when the control rods have been returned to AUTO.  
: 2. You are to notify the US when the control rods have been returned to AUTO.  


Line 1,405: Line 1,405:
1-FCV-65 Open.
1-FCV-65 Open.
1-FCO-65 Open.
1-FCO-65 Open.
1-HS-65-81/86 - OPEN 1-HS-65-83/87 in A-AUTO STANDBY 0-HS-65-23A - RUNNING.  
1-HS-65-81/86 - OPEN 1-HS-65-83/87 in A-AUTO STANDBY 0-HS-65-23A - RUNNING.
: 3. Acknowledge all alarms.  
: 3. Acknowledge all alarms.
: 5. Freeze simulator until the applicant indicates understanding of the task and time is allowed for control board familiarization.  
: 5. Freeze simulator until the applicant indicates understanding of the task and time is allowed for control board familiarization.
: 5. After applicant indicates understanding of task, place simulator in run.
: 5. After applicant indicates understanding of task, place simulator in run.
Tools/Equipment/Procedures Needed:
Tools/Equipment/Procedures Needed:
Line 1,417: Line 1,417:
DIRECTION TO APPLICANT I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
DIRECTION TO APPLICANT I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit 1 is at 100% power.  
: 1. Unit 1 is at 100% power.
: 2. 0-SI-65-6-A "Emergency Gas Treatment System Train A 10-Hour Operation" performance in progress.  
: 2. 0-SI-65-6-A "Emergency Gas Treatment System Train A 10-Hour Operation" performance in progress.
: 3. "A" Train EGTS Fan has been in service for 10 hours.  
: 3. "A" Train EGTS Fan has been in service for 10 hours.
: 4. You are a support operator in the control room.
: 4. You are a support operator in the control room.
INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor directs you to shutdown the "A" Train EGTS Fan per SOI-65.02 and return EGTS to Standby Alignment per the procedure.  
: 1. The Unit Supervisor directs you to shutdown the "A" Train EGTS Fan per SOI-65.02 and return EGTS to Standby Alignment per the procedure.
: 2. You are to notify Unit Supervisor when you have completed the task.  
: 2. You are to notify Unit Supervisor when you have completed the task.  


Line 1,467: Line 1,467:
___ SAT  
___ SAT  


___ UNSAT STEP 5: [Step 4] PERFORM the following: [a] CLOSE 1-FCV-65-10, EGTS TR-A U1 SUCT DMPR.  
___ UNSAT STEP 5: [Step 4] PERFORM the following: [a] CLOSE 1-FCV-65-10, EGTS TR-A U1 SUCT DMPR.
[b] CLOSE 1-FCO-65-26, EGTS TO U1 SHIELD BLDG.  
[b] CLOSE 1-FCO-65-26, EGTS TO U1 SHIELD BLDG.  


Line 1,539: Line 1,539:


REV. 0 PAGE 89 OF 131 WATTS BAR NUCLEAR PLANT B.1.h  STEP 13: [STEP 5] ENSURE breaker position for the following:
REV. 0 PAGE 89 OF 131 WATTS BAR NUCLEAR PLANT B.1.h  STEP 13: [STEP 5] ENSURE breaker position for the following:
NOMENCLATURE LOCATION POSITION UNID 120VAC VITAL INST POWER BD 1-II EGTS TRAIN B AUX RELAYS 1-PCV-65-81/1-PCV-65-86 Bkr 38 OFF 1-BKR-235-2/38 STANDARD: Applicant contacts an AUO and requests performance of Step  
NOMENCLATURE LOCATION POSITION UNID 120VAC VITAL INST POWER BD 1-II EGTS TRAIN B AUX RELAYS 1-PCV-65-81/1-PCV-65-86 Bkr 38 OFF 1-BKR-235-2/38 STANDARD: Applicant contacts an AUO and requests performance of Step
: 5.  **CUE: When asked as the AUO, stat e"1-BKR-235-2/38 is in the OFF position".
: 5.  **CUE: When asked as the AUO, stat e"1-BKR-235-2/38 is in the OFF position".


Line 1,635: Line 1,635:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit 1 is at 100% power.  
: 1. Unit 1 is at 100% power.
: 2. 0-SI-65-6-A "Emergency Gas Treatment System Train A 10-Hour Operation" performance in progress.  
: 2. 0-SI-65-6-A "Emergency Gas Treatment System Train A 10-Hour Operation" performance in progress.
: 3. "A" Train EGTS Fan has been in service for 10 hours.  
: 3. "A" Train EGTS Fan has been in service for 10 hours.
: 4. You are a support operator in the control room.  
: 4. You are a support operator in the control room.  


INITIATING CUES:
INITIATING CUES:
: 1. The Unit Supervisor directs you to shutdown the "A" Train EGTS Fan per SOI-65.02 and return EGTS to Standby Alignment per the procedure.  
: 1. The Unit Supervisor directs you to shutdown the "A" Train EGTS Fan per SOI-65.02 and return EGTS to Standby Alignment per the procedure.
: 2. You are to notify Unit Supervisor when you have completed the task.  
: 2. You are to notify Unit Supervisor when you have completed the task.  


Line 1,684: Line 1,684:
: 1. The Reactor has been tripped and AOI-34, "IMMEDIATE BORATION,"
: 1. The Reactor has been tripped and AOI-34, "IMMEDIATE BORATION,"
is being performed due to an RCS cooldown resulting in temperature less than 547
is being performed due to an RCS cooldown resulting in temperature less than 547
°F. 2. The normal makeup controls did not function correctly to establish boric acid flow. 3. Both Boric Acid pumps are operating in FAST speed.  
°F. 2. The normal makeup controls did not function correctly to establish boric acid flow. 3. Both Boric Acid pumps are operating in FAST speed.
: 4. 1-FCV-62-138 did not open from the Main Control Room.
: 4. 1-FCV-62-138 did not open from the Main Control Room.
INITIATING CUES:
INITIATING CUES:
: 1. You have been assigned to perform AOI-34, "IMMEDIATE BORATION,"
: 1. You have been assigned to perform AOI-34, "IMMEDIATE BORATION,"
Step 6 actions to locally establish boric acid flow.  
Step 6 actions to locally establish boric acid flow.
: 2. You are to establish a minimum boric acid flow rate of 45 gpm.  
: 2. You are to establish a minimum boric acid flow rate of 45 gpm.  


Line 1,765: Line 1,765:
Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you. INITIAL CONDITIONS:
Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you. INITIAL CONDITIONS:
: 1. The Reactor has been tripped and AOI-34 is being performed due to an RCS cooldown resulting in temperature less than 547
: 1. The Reactor has been tripped and AOI-34 is being performed due to an RCS cooldown resulting in temperature less than 547
°F. 2. The normal makeup controls did not function correctly to establish boric acid flow. 3. Both Boric Acid pumps are operating in FAST speed.  
°F. 2. The normal makeup controls did not function correctly to establish boric acid flow. 3. Both Boric Acid pumps are operating in FAST speed.
: 4. 1-FCV-62-138 did not open from the Main Control Room. INITIATING CUES:
: 4. 1-FCV-62-138 did not open from the Main Control Room. INITIATING CUES:
: 1. You have been assigned perform AOI-34, Step 6.b RNO actions to locally establish boric acid flow.  
: 1. You have been assigned perform AOI-34, Step 6.b RNO actions to locally establish boric acid flow.
: 3. You are to establish a minimum boric acid flow rate of 45 gpm.  
: 3. You are to establish a minimum boric acid flow rate of 45 gpm.  


Line 1,810: Line 1,810:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit 1 is in Mode 3 after a Steam Generator tube rupture on S/G # 2.  
: 1. Unit 1 is in Mode 3 after a Steam Generator tube rupture on S/G # 2.
: 2. The Main Steam Isolation Valve (MSIV) on S/G # 2 has failed to close.  
: 2. The Main Steam Isolation Valve (MSIV) on S/G # 2 has failed to close.
: 3. Main Steam line warming is NOT in progress.  
: 3. Main Steam line warming is NOT in progress.  


INITIATING CUES:
INITIATING CUES:
: 1. The MCR operator has directed you to locally isolate the steam traps and main feed pump turbine on the main steam system by performing E-3, "Steam Generator Tube Rupture," Attachment 3, "Steamline Isolation (Local)."  
: 1. The MCR operator has directed you to locally isolate the steam traps and main feed pump turbine on the main steam system by performing E-3, "Steam Generator Tube Rupture," Attachment 3, "Steamline Isolation (Local)."
: 2. You are to notify the MCR operator when E-3, Attachment 3 has been completed.  
: 2. You are to notify the MCR operator when E-3, Attachment 3 has been completed.  


Line 1,976: Line 1,976:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. Unit 1 is in Mode 3 after a Steam Generator tube rupture on S/G # 2.  
: 1. Unit 1 is in Mode 3 after a Steam Generator tube rupture on S/G # 2.
: 2. The Main Steam Isolation Valve (MSIV) on S/G # 2 has failed to close.  
: 2. The Main Steam Isolation Valve (MSIV) on S/G # 2 has failed to close.
: 3. Main Steam line warming is NOT in progress.  
: 3. Main Steam line warming is NOT in progress.  


INITIATING CUES:
INITIATING CUES:
: 1. The MCR operator has directed you to locally isolate the steam traps and main feed pump turbine on the main steam system by performing E-3, "Steam Generator Tube Rupture," Attachment 3, "Steamline Isolation (Local)."  
: 1. The MCR operator has directed you to locally isolate the steam traps and main feed pump turbine on the main steam system by performing E-3, "Steam Generator Tube Rupture," Attachment 3, "Steamline Isolation (Local)."
: 2. You are to notify the MCR operator when E-3, Attachment 3 has been completed.  
: 2. You are to notify the MCR operator when E-3, Attachment 3 has been completed.  


Line 2,019: Line 2,019:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. The Unit is at 100% power.  
: 1. The Unit is at 100% power.
: 2. Letdown orifice valve 1-FCV-62-74 is open and letdown flow (as indicated in MCR) is 75 gpm.  
: 2. Letdown orifice valve 1-FCV-62-74 is open and letdown flow (as indicated in MCR) is 75 gpm.
: 3. RCS boron concentration is 776 ppm.  
: 3. RCS boron concentration is 776 ppm.
: 4. Chemistry has requested that cation bed be placed in service for 53 minutes.  
: 4. Chemistry has requested that cation bed be placed in service for 53 minutes.
: 5. The Cation bed has been filled and vented.  
: 5. The Cation bed has been filled and vented.
: 6. SOI-62.04, "CVCS PURIFICATION SYSTEM," Attachment 1, Resin Status Sheet indicates that the Cation Bed is at the same boron concentration of the RCS.
: 6. SOI-62.04, "CVCS PURIFICATION SYSTEM," Attachment 1, Resin Status Sheet indicates that the Cation Bed is at the same boron concentration of the RCS.
INITIATING CUES:
INITIATING CUES:
: 1. The MCR operator has directed you to place the CVCS Cation Bed in service per procedure.  
: 1. The MCR operator has directed you to place the CVCS Cation Bed in service per procedure.
: 2. You are to notify the MCR when the CVCS Cation Bed is in service.   
: 2. You are to notify the MCR when the CVCS Cation Bed is in service.   


Line 2,161: Line 2,161:
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.
INITIAL CONDITIONS:
INITIAL CONDITIONS:
: 1. The Unit is at 100% power.  
: 1. The Unit is at 100% power.
: 2. Letdown orifice valve 1-FCV-62-74 is open and letdown flow (as indicated in MCR) is 75 gpm.  
: 2. Letdown orifice valve 1-FCV-62-74 is open and letdown flow (as indicated in MCR) is 75 gpm.
: 3. RCS boron concentration is 776 ppm.  
: 3. RCS boron concentration is 776 ppm.
: 4. Chemistry has requested that cation bed be placed in service for 53 minutes.  
: 4. Chemistry has requested that cation bed be placed in service for 53 minutes.
: 5. The Cation bed has been filled and vented.  
: 5. The Cation bed has been filled and vented.
: 6. SOI-62.04, "CVCS PURIFICATION SYSTEM," Attachment 1, Resin Status Sheet indicates that the Cation Bed is at the same boron concentration of the RCS.
: 6. SOI-62.04, "CVCS PURIFICATION SYSTEM," Attachment 1, Resin Status Sheet indicates that the Cation Bed is at the same boron concentration of the RCS.
INITIATING CUES:
INITIATING CUES:
: 1. The MCR operator has directed you to place the CVCS Cation Bed in service per procedure.  
: 1. The MCR operator has directed you to place the CVCS Cation Bed in service per procedure.
: 2. You are to notify the MCR when the CVCS Cation Bed is in service.}}
: 2. You are to notify the MCR when the CVCS Cation Bed is in service.}}

Revision as of 18:26, 11 July 2019

Initial Exam 2009-301 Final Sim/In-Plant JPMs
ML092810562
Person / Time
Site: Watts Bar  Tennessee Valley Authority icon.png
Issue date: 10/08/2009
From:
NRC/RGN-II
To:
References
50-390/09-301, 50-391/09-301
Download: ML092810562 (131)


Text

REV. 0 PAGE 1 0F 131 WATTS BAR NUCLEAR PLANT B.1.a

ALTERNATE PATH.

B.1.a Withdraw Shutdown Banks.

REV. 0 PAGE 2 0F 131 WATTS BAR NUCLEAR PLANT B.1.a Task: Withdraw Shutdown Banks.

Alternate Path:

Following failure of the group step counters, the reactor trip breakers are opened in accordance with Technical Requirement 3.1.7.

Facility JPM #: B.1.a 2009 May NRC Exam.

K/A Rating(s):

001 Control Rod Drive System. A3.05, Ability to monitor automatic operation of the CRDS, including: Individual vs. group rod position.

[3.5/3.5] (CFR: 41.7/45.13)

Task Standard: Withdrawal of shutdown banks is initiated starting with Shutdown Bank A.

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __X__ In-Plant _____ Perform __X___ Simulate ___ _

References

SOI-85.01, "Control Rod Drive and Position Indication System," Rev. 38. TR 3.1.7, "Reactivity Control Systems, Position Indicating System - Shutdown." AOI-2, "Malfunction of Reactor Control System," Rev. 37.

Task Number: RO-085-SOI-85-001 APPLICABLE FOR: RO/SRO RO-085-SOI-85-010 10CFR55.45

CFR: 41.7/45.13 Validation Time: 10 min. Time Critical:

No ===========================================================================

Applicant: ___________________________ _________________ Time Start: ________

NAME SSNTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 0 PAGE 3 0F 131 WATTS BAR NUCLEAR PLANT B.1.a SIMULATOR OPERATOR INSTRUCTIONS:

1. Initialize to IC 311. a. Ensure the following items are displayed on the Director Summary Page:

rd19 Shutdown bank a demand counter fails 0

b. Load NRC_Exam_Event_Files.evt from the NRC Exam Flash Drive. Event 20 is set when Shutdown Bank A reaches 110 steps. Malfunction rd19 will enter at this event.
c. Place the simulator in RUN momentarily, and reset the High Flux at Shutdown alarm, and then acknowledge all alarms
3. ENSURE 1-NR-92-145 Recorder is selected to Source Range N31 and Intermediate Range N35.
4. Freeze simulator until the applicant indicates understanding of the task and time is allowed for control board familiarization.
5. After applicant indicates understanding of task, place simulator in run.

Tools/Equipment/Procedures Needed:

Marked copy of SOI-85.01, indicating steps have been performed to Section 5.4, Step 6.

REV. 0 PAGE 4 0F 131 WATTS BAR NUCLEAR PLANT B.1.a READ TO APPLICANT

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. A unit startup is in progress following a trip from 100% power due to a generator electrical relay malfunction that occurred 6 days ago.
2. Per the Nuclear Operating Book (NOB), Sheet 7 BANK OVERLAP AND ROD INSERTION LIMITS, the shutdown banks fully withdrawn position is 230 steps.
3. GO-2, "Reactor Startup," Section 3.2 "Actions Performed Before Startup," is complete to Step [13.10], WITHDRAW Shutdown Rods to fully withdrawn per SOI-85.01.
4. The US/SRO has approved shutdown bank withdrawal.
5. SOI-85.01, "Control Rod Drive and Indication System," is being performed and is complete to through Section 5.4, Step 5.
6. All reactivity briefs required by SPP-10.4, "Reactivity Management Program" have been completed.

INITIATING CUES:

1. You are to continue the performance of SOI-85.01 at Section 5.4 Step 6, and withdraw the shutdown banks.
2. Notify the SRO when the shutdown banks are fully withdrawn.

REV. 0 PAGE 5 0F 131 WATTS BAR NUCLEAR PLANT B.1.a START TIME: _______

STEP/STANDARD SAT/UNSAT STEP 1.: Obtain the appropriate procedure.

STANDARD: Applicant identifies SOI-85.01 and goes to Section 5.4 "Shutdown Banks Withdrawal."

Evaluator Cue: Hand marked-up copy of SOI-85.01 to the Applicant after the Applicant successfully identifies the procedure and section.

___ SAT

___ UNSAT

STEP 2: [6] ENSURE 1-RBSS, ROD BANK SELECTOR SWITCH [1-M-4], in MANUAL.

STANDARD: Applicant ensures that the Rod Bank Selector Switch RBSS-1 is in MANUAL position.

COMMENTS:

___ SAT

___ UNSAT

STEP 3: [7] OBTAIN SRO Approval to withdraw Shutdown Banks.

STANDARD: If requested, state that SRO approval has been granted.

COMMENTS:

___ SAT

___ UNSAT

REV. 0 PAGE 6 0F 131 WATTS BAR NUCLEAR PLANT B.1.a STEP/STANDARD SAT/UNSAT STEP 4: [8] OBSERVE the following for proper response during Bank Withdrawal:

A. Source Range (SR) ________

B. Intermediate Range (IR) ________

C. Startup Meters ________

D. Nuclear Recorders ________

STANDARD: Applicant monitors above parameters as the rods are being withdrawn.

COMMENTS:

___ SAT

___ UNSAT

STEP 5: [9] SELECT SD Bank A (SBA) on ROD BANK SELECTOR SWITCH, 1-RBSS.

STANDARD: Applicant places Rod Bank Selector switch RBSS-1 in SBA position.

COMMENTS:

Critical Step

___ SAT

___ UNSAT

STEP 6: [10] PLACE 1-FLRM, IN-HOLD-OUT SWITCH, to OUT to begin withdrawing Shutdown Banks A1 and A2 to greater than or equal to 225 Steps.

STANDARD: Applicant places 1-FLR to the OUT position and monitors shutdown bank A group A1 and A2 are responding.

COMMENTS:

Critical Step

___ SAT

___ UNSAT

REV. 0 PAGE 7 0F 131 WATTS BAR NUCLEAR PLANT B.1.a STEP/STANDARD SAT/UNSAT STEP 7: [11] MONITOR the following as the Bank is being withdrawn: A. Group Step Counters B. RPIs C. "In-Out" Status Lights D. Rod speed (64 Steps/Minute)

STANDARD: Applicant monitors parameters as the rods are being withdrawn.

COMMENTS:

___ SAT

___ UNSAT

Note to evaluator:

Malfunction to fail step counters is to be inserted when Shutdown Bank A rods reach approximately 110 steps.

Applicant may refer to TR-3.1.7. If so, the required action is to open the Reactor Trip

breakers.

NOTE TO EVALUATOR:

If applicant has identified the failure and informs the evaluator, cue the applicant to "take your appropriate actions."

STEP 9: Open the Reactor Trip Breakers.

STANDARD: Applicant determines the Group 1 step counter is not capable of determining the demand position for each of the Shutdown bank A rods within +

2 steps and opens the reactor trip breakers.

Cue: After the reactor trip breakers have been opened state "This completes this JPM."

COMMENTS:

Critical Step

___ SAT

___ UNSAT

STOP TIME ________

REV. 0 PAGE 8 0F 10 WATTS BAR NUCLEAR PLANT B.1.b DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. A unit startup is in progress following a trip from 100% power due to a generator electrical relay malfunction that occurred 6 days ago.
2. Per the Nuclear Operating Book (NOB), Sheet 7 BANK OVERLAP AND ROD INSERTION LIMITS, the shutdown banks fully withdrawn position is 230 steps.
3. GO-2, "Reactor Startup," Section 3.2 "Actions Performed Before Startup," is complete to Step [13.10], WITHDRAW Shutdown Rods to fully withdrawn per SOI-85.01.
4. The US/SRO has approved shutdown bank withdrawal.
5. SOI-85.01, "Control Rod Drive and Indication System," is being performed and is complete to through Section 5.4, Step 5.
6. All reactivity briefs required by SPP-10.4, "Reactivity Management Program" have been completed.

INITIATING CUES:

1. You are to continue the performance of SOI-85.01 at Section 5.4 Step 6, and withdraw the shutdown banks.
2. Notify the SRO when the shutdown banks are fully withdrawn.

REV. 0 PAGE 9 0F 10 WATTS BAR NUCLEAR PLANT B.1.b

B.1.b Place Excess Letdown in Service per AOI-6.

REV. 0 PAGE 10 0F 10 WATTS BAR NUCLEAR PLANT B.1.b EVALUATION SHEET Task: Place Excess Letdown in Service per AOI-6.

Alternate Path:

N/A Facility JPM #: 3-OT-JPMR022 Rev 3.

K/A Rating(s):

004 Chemical and Volume Control System. A4.06 Ability to manually operate and/or monitor in the control room: Letdown isolation and flow control valves. [3.6/3.1]. (CFR: 41/7 / 45.5 to 45.8).

Task Standard: Excess letdown has been placed in service per AOI-6, "Small Reactor Coolant System Leak," Step 15.

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __X__ In-Plant _____ Perform __X___ Simulate ____

References

AOI-6, "Small Reactor Coolant System Leak," Rev 32.

Task Number: RO-062-SOI-62-007 APPLICABLE FOR: RO/SRO RO-068-AOI-6-001 10CFR55.45: 6, 12 Validation Time: 10 min.

Time Critical:

No ===========================================================================

Applicant: ___________________________ _________________ Time Start: ________

NAME SSNTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 0 PAGE 11 0F 10 WATTS BAR NUCLEAR PLANT B.1.b REV. 0 PAGE 12 0F 10 WATTS BAR NUCLEAR PLANT B.1.b SIMULATOR OPERATOR INSTRUCTIONS:

1. Initialize to IC 312. a. Ensure following letdown and charging isolation valves are closed.
a. 1-FCV-62-72.
b. 1-FCV-62-73.
c. 1-FCV-62-74.
d. 1-FCV-62-76.
e. 1-FCV-62-69.
f. 1-FCV-62-70.
g. 1-FCV-62-85.
h. 1-FCV-62-86.
i. 1-FCV-62-90.
j. 1-FCV-62-91.
b. Ensure 1-FCV-62-93 is in manual and seal flow is stable at approximately 8 gpm per RCP seal.
c. Ensure pressurizer level is approximately 66% and rising slowly.
2. Acknowledge all alarms.
3. Place simulator in FREEZE until the applicant indicates an understanding of the task.
4. After applicant indicates understanding of the task, place simulator to RUN.

Tools/Equipment/Procedures Needed:

A marked up copy of AOI-6, signed off through Step 14, with Step 15 CIRCLED.

REV. 0 PAGE 13 0F 10 WATTS BAR NUCLEAR PLANT B.1.b READ TO APPLICANT

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. The Unit is operating at 100% power.
2. A small leak has been found on the normal letdown path.
3. Letdown and Charging have been isolated per AOI-6, "Small Reactor Coolant System Leak."
4. The RADPRO Supervisor has been informed of the intent to establish Excess Letdown. 5. You are the Operator at the Controls.

INITIATING CUES:

1. The Unit Supervisor has directed you to establish excess letdown to the VCT per AOI-6, "Small Reactor Coolant System Leak." Section 3.0, and Step 15, RESPONSE NOT OBTAINED.
2. You are to notify the Unit Supervisor when excess letdown has been aligned and pressurizer level is under control.

REV. 3 PAGE 14 0F 10 WATTS BAR NUCLEAR PLANT B.1.b START TIME: _______

STEP 1: Obtain a copy of the procedure.

STANDARD: A copy of AOI-6 has been obtained.

COMMENTS: ___ SAT

___ UNSAT

STEP 2: Check pressurizer level DROPPING or STABLE.

STANDARD: Applicant observes a RISING trend on pressurizer level and enters RESPONSE NOT OBTAINED column for actions.

NOTE: Use of the RNO Column was directed by the INITIATING CUES.

COMMENTS:

___ SAT

___ UNSAT

STEP 3: If pzr level is rising, THEN PLACE excess letdown in service.

STANDARD: Applicant enters the RESPONSE NOT OBTAINED column and begins procedure actions.

NOTE: Use of the RNO Column was directed by the INITIATING CUES.

COMMENTS:

___ SAT

___ UNSAT

REV. 3 PAGE 15 0F 10 WATTS BAR NUCLEAR PLANT B.1.b STEP 4 : a. OPEN 1-FCV-70-143

STANDARD: At panel 1-M-27B the applicant places 1-HS 143A to OPEN. Applicant verifies the RED light is LIT and the GREEN light is OFF. Step is critical to establish excess letdown flow.

NOTE: When the applicant opens 1-FCV-70-143, Annunciator 239-D will be received. This alarm occurs whenever 1-FCV-70-143 is OPEN and flow on 1-FS-70-8 is less than

230 gpm.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT STEP 5 : b. OPEN 1-FCV-70-85

STANDARD: At panel 1-M-27B the Applic ant places 1-HS-70-85A to OPEN and holds the switch to OPEN until the RED light is LIT and the GREEN light is OFF. Step is critical to establish excess letdown flow.

NOTE: When the applicant opens 1-FCV-70-85, Annunciator 239-D will clear as soon as flow is greater than 230 gpm Applicant may use 1-FI-70-84 (panel 1-M-27B) to monitor flow.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT STEP 6 : c. OPEN 1-FCV-62-54

STANDARD: At panel 1-M-5 the applicant places 1-HS-62-54 to OPEN and holds the switch to OPEN until the RED light is LIT and the GREEN light is OFF. Step is critical to establish excess letdown flow.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT

REV. 3 PAGE 16 0F 10 WATTS BAR NUCLEAR PLANT B.1.b STEP 7 : d. OPEN 1-FCV-62-55

STANDARD: At panel 1-M-5 the applicant places 1-HS-62-55 to OPEN and holds the switch to OPEN until the RED light is LIT and the GREEN light is OFF. Step is critical to establish excess letdown flow.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT STEP 8 : e. ENSURE 1-FCV-62-59 is in NORMAL.

STANDARD: At panel 1-M-5 the applicant determines that 1-HS-62-59A is in the NORM position, with the RED seal return light LIT.

COMMENTS:

___ SAT

___ UNSAT STEP 9: f. ADJUST 1-HIC-62-56A to obtain maximum flow and maintain excess letdown hx outlet temp less than 200

°F.

STANDARD: At panel 1-M-5 the applicant opens 1-HIC-62-56A while monitoring 1-TI-62-58. Excess letdown temperature must remain below 200

°F as indicated on 1-TI-62-58. Step is critical to establish excess letdown flow.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT

REV. 3 PAGE 17 0F 10 WATTS BAR NUCLEAR PLANT B.1.b STEP 10: STABILIZE pzr level by adjusting seal injection and excess letdown flows.

STANDARD: At panel 1-M-5 the applicant observes pzr level trend on 1-LR-68-339. Applicant may also set up a trend of pzr level on ICS computer using inputs from 1-LI-68-339A, 1-LI-68-335A and 1-LI-68-320.

COMMENTS:

___ SAT

___ UNSAT

STEP 11: Notify the Unit Supervisor that Excess Letdown has been placed in service.

STANDARD: The Unit Supervisor has been notified that Excess Letdown has been placed in service.

    • CUE: When notified, acknowledge the report.

COMMENTS:

END OF TASK

___ SAT

___ UNSAT STOP TIME: ________

REV. 0 PAGE 18 OF 131 WATTS BAR NUCLEAR PLANT B.1.c DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned

task. INITIAL CONDITIONS:

1. The Unit is operating at 100% power.
2. A small leak has been found on the normal letdown path.
3. Letdown and Charging have been isolated per AOI-6, "Small Reactor Coolant System Leak."
4. The RADPRO Supervisor has been informed of the intent to establish Excess Letdown. 5. You are the Operator at the Controls.

INITIATING CUES:

1. The Unit Supervisor has directed you to establish excess letdown to the VCT per AOI-6, "Small Reactor Coolant System Leak." Section 3.0, and Step 15, RESPONSE NOT OBTAINED.
2. You are to notify the Unit Supervisor when excess letdown has been aligned and pressurizer level is under control.

REV. 0 PAGE 19 OF 131 WATTS BAR NUCLEAR PLANT B.1.c

ALTERNATE PATH.

B.1.c Isolate Cold Leg Accumulators per E-1.

REV. 0 PAGE 20 OF 131 WATTS BAR NUCLEAR PLANT B.1.c Task: Isolate Cold Leg Accumulators per E-1.

Alternate Path:

Cold Leg Accumulator #4 cannot be isolated and must be vented to comply with E-1,"Loss of Reactor or Secondary Coolant," Step 26 RNO.

Facility JPM #: N/A K/A Rating(s):

011 Large Break LOCA. EA1.09 Ability to operate and monitor the following as they apply to a Large Break LOCA: Core flood tank initiation. [4.3/4.3] (CFR 41.7 / 45.5 / 45.6).

Task Standard: Cold Leg Accumulators 1, 2, and 3 are isolated per E-1,"Loss of Reactor or Secondary Coolant," Step 26 AER. Cold Leg Accumulator 4 is vented, per E-1,"Loss of Reactor or Secondary Coolant," Step 26 RNO.

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __X__ In-Plant _____ Perform __X___ Simulate ___ _

References

E-1,"Loss of Reactor or Secondary Coolant," Rev. 15 Task Number: RO-063-SOI-63-003 APPLICABLE FOR: RO/SRO 10CFR55.45: 5, 6 Validation Time: 15 min.

Time Critical:

No ===========================================================================

Applicant: ___________________________ _________________ Time Start: ________

NAME SSNTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 0 PAGE 21 OF 131 WATTS BAR NUCLEAR PLANT B.1.c REV. 0 PAGE 22 OF 131 WATTS BAR NUCLEAR PLANT B.1.c SIMULATOR OPERATOR INSTRUCTIONS:

1. Initialize to IC 313. a. Ensure the following items are displayed on the Director Summary Page:

th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity hs-63-67a hs-63-67a sis accumulator tank 4 flow isolation valve Open

b. Ensure that the following remote is set as indicated on the Director Remote Page. sir01 pwr to cold leg accumu isolation valves fcv-63-67, 80, 98, 119 on
c. Place the simulator in RUN momentarily, and acknowledge all alarms.
4. Place simulator in FREEZE until the Applicant indicates an understanding of the task.
3. After Applicant indicates understanding of the task, place simulator to RUN.

Tools/Equipment/Procedures Needed:

A marked-up copy of E-1, signed off through Step 25, with Step 26 circled.

REV. 0 PAGE 23 OF 131 WATTS BAR NUCLEAR PLANT B.1.c READ TO APPLICANT

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. A large break LOCA has occurred.
2. E-1,"Loss of Reactor or Secondary C oolant,"performance has just been resumed after performance of ES-1.3,"Tra nsfer to Containment Sump."
3. You are the Control Room Operator.

INITIATING CUES:

1. The Unit Supervisor directs you perf orm E-1,"Loss of Reactor or Secondary Coolant," Step 26, DETERM INE if cold leg accumulato rs should be isolated.
2. You are to notify the Unit Supervisor when you have completed Step 26.

REV. 0 PAGE 24 OF 131 WATTS BAR NUCLEAR PLANT B.1.c START TIME: _______

STEP 1: Obtain a copy of the procedure.

STANDARD: A copy of E-1 has been obtained EXAMINER'S CUE:

After the applicant has de monstrated the method of obtaining the correct instruction, the examiner will

provide a marked-up copy of the instruction.

COMMENTS:

___ SAT

___ UNSAT STEP 2: a. ENSURE power to isolation valves restored USING Appendix A (E-1), CLA Breaker Operation.

STANDARD:

EXAMINER'S CUE: When asked, inform the applicant that E-1 Appendix A CLA BREAKER OPERATION is complete.

COMMENTS:

___ SAT

___ UNSAT REV. 0 PAGE 25 OF 131 WATTS BAR NUCLEAR PLANT B.1.c STEP 3: b. CHECK RCS pressure less than 250 psig.

STANDARD: Applicant reads RCS pressure from one of the following PAM instruments and determines that pressure is approximately 70 psig.

RVLIS-ICCM PLASMA DISPLAY on 1-M-4 or 1-M-6.

Loop 4 HL PRESS 1-PI-68-70.

Loop 3 HL PRESS 1-PI-68-64.

Loop 2 HL Press 1-PI-68-63.

COMMENTS:

___ SAT

___ UNSAT STEP 4: c. CLOSE cold leg accumulator isolation valves.

STANDARD: Applicant places 1-HS-63-118, 1-HS-63-98, 1-HS-63-80 and 1-HS-63-67 to close. Applicant observes that 1-HS-63-67 indicating lights do not change, indicating that 1-FCV-63-67, CLA 4 Isolation valve remains OPEN. Step is critical since this action is taken to minimize the chance of nitrogen injection into the RCS.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT STEP 5: c. RESPONSE NOT OBTAINED PERFORM the following:

STANDARD: Applicant determines that RNO actions are required since 1-FCV-63-67 did NOT CLOSE.

COMMENTS:

___ SAT

___ UNSAT REV. 0 PAGE 26 OF 131 WATTS BAR NUCLEAR PLANT B.1.c STEP 6: 1) RESET Phase B STANDARD:

Applicant observes the Phase B lights on the Master Isolation Signal Status panels 1-XX-55-6C and 1-XX-55-6D on 1-M-6 are LIT, indicating that Phase B has been actuated.

Applicant depresses 1-HS-30-64D B CNTMT ISOL RESET TR-A, and observes the B light goes DARK on 1-XX-55-6C Substep is critical since this action is taken to allow the air supply to the nitrogen makeup and vent valves to be restored. Applicant depresses 1-HS-30-64E B CNTMT ISOL RESET TR-B, and observes the B light goes DARK 1-XX-55-6D.

Substep is critical since this action is taken to allow the air supply to the nitrogen makeup and vent valves to be restored.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT REV. 0 PAGE 27 OF 131 WATTS BAR NUCLEAR PLANT B.1.c STEP 7: 2) ENSURE aux air pressure to cntmt is greater than 75 psig [M-15] AND OPEN cntmt air supply valves.

STANDARD:

Applicant observes air pressure on 0-PI-32-104A, Aux Air A Press and 0-PI-32-105A, Aux Air Press indicate 95 psig and that 1-FCV-32-80, 1-FCV-32-102, and 1-FCV-32-110 are CLOSED.

Applicant places 1-HS-30-80A in the OPEN position and holds until RED light is LIT, GREEN light is DARK. Step is critical since this action is taken to allow the air supply to the nitrogen makeup and vent valves to be restored.

Applicant places 1-HS-30-102A in the OPEN position and holds until RED light is LIT, GREEN light is DARK. Step is critical since this action is taken to allow the air supply to the nitrogen makeup and vent valves to be restored.

Applicant places 1-HS-30-110A in the OPEN position and holds until RED light is LIT, GREEN light is DARK. Step is critical since this action is taken to allow the air supply to the nitrogen makeup and vent valves to be restored.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT REV. 0 PAGE 28 OF 131 WATTS BAR NUCLEAR PLANT B.1.c STEP 8: 3) OPEN any unisolated accumulator's nitrogen makeup valve.

STANDARD: Applicant determines that 1-FCV-63-63 for CLA 4 must be OPENED.

Applicant places 1-HS-63-63A N2 TO CL ACCUM 4 to OPEN position, and verifies RED light is LIT GREEN light is DARK.

Step is critical since this action is taken to minimize the chance of nitrogen injection into the RCS.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT STEP 8: 4) OPEN 1-FCV-63-65 vent header.

STANDARD: Applicant rotates 1-HIC-63-65A in the counterclockwise direction to OPEN 1-FCV-63-65 FULLY.

Step is critical since this action is taken to minimize the chance of nitrogen injection into the RCS.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT

STEP 9: Notify the Unit Supervisor that E-1, Step 26 is complete.

STANDARD: Applicant notifies the Unit Supervisor that Step 26 is complete

COMMENTS:

END OF TASK

___ SAT

___ UNSAT STOP TIME ________

REV. 6 PAGE 29 OF 131 WATTS BAR NUCLEAR PLANT B.1.d DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. A large break LOCA has occurred.
2. E-1,"Loss of Reactor or Secondary C oolant,"performance has just been resumed after performance of ES-1.3,"Tra nsfer to Containment Sump."
3. You are the Control Room Operator.

INITIATING CUES:

1. The Unit Supervisor directs you perf orm E-1,"Loss of Reactor or Secondary Coolant," Step 26, DETERM INE if cold leg accumulato rs should be isolated.
2. You are to notify the Unit Supervisor when you have completed Step 26.

REV. 6 PAGE 30 OF 131 WATTS BAR NUCLEAR PLANT B.1.d

ALTERNATE PATH.

B.1.d Place RHR Spray in Service per FR-Z.1, "High Containment Pressure."

REV. 6 PAGE 31 OF 131 WATTS BAR NUCLEAR PLANT B.1.d EVALUATION SHEET Task: Place RHR Spray in Service per FR-Z.1, "High Containment Pressure."

Alternate Path:

When the Applicant attempts to close 1-FCV-63-94, the valve will NOT close. This requires entry into the RNO in order to place Train A RHR Spray in service. Facility JPM #: 3-OT-JPMR016A Rev 5.

K/A Rating(s):

005 Residual Heat Removal System. A4.01 Ability to manually operate and/or monitor in the control room: Controls and indication for RHR pumps [3.6/3.4] (CFR: 41.7 / 45.5 to 45.8)

Task Standard: Train "A" of RHR Spray has been placed in-service per FR-Z.1, "High Containment Pressure."

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __X__ In-Plant __ ___ Perform __X____ Simulate ____

References

FR-Z.1, "High Containment Pressure,"Rev.10 Task Number: RO-113-FR-Z.1-001 APPLICABLE FOR: RO/SRO 10CFR55.45: 3, 4, 6, 7, 8 Validation Time: 10 min.

Time Critical:

No ===========================================================================

Candidate: ___________________________ _________________ Time Start: ________

NAME SSN/EINTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 6 PAGE 32 OF 131 WATTS BAR NUCLEAR PLANT B.1.d REV. 6 PAGE 33 OF 131 WATTS BAR NUCLEAR PLANT B.1.d SIMULATOR OPERATOR INSTRUCTIONS:

1. Initialize to IC 314. a. Ensure the following items are displayed on the Director Summary Page:

th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity ch01a containment pressure transmitter failure pdt-3-42 14 ch01b containment pressure transmitter failure pdt-3-43 14 ch01c containment pressure transmitter failure pdt-3-44 14 ch01d containment pressure transmitter failure pdt-3-45 14 ei-72-12a 07020 cntmt spray pmp b amps 35 fi-72-13 07010 cntmt spray pmp b flow 3000 hs-72-10a-3 06010 cntmt spray pump b mtr sw(red) on hs-72-10a-1 06010 cntmt spray pump b mtr sw(green) off hs-72-27a-1 06020 cntmt spray pump a mtr sw(green) off pdi-30-42 03160 cntmt press diff indicator 12 pdi-30-43 03170 cntmt press diff indicator 12 pdi-30-44 03180 cntmt press diff indicator 12 pdi-30-45 03190 cntmt press diff indicator 12 pdr-30-133-1 03150 cntmt annulus dp indicator 0.5 hs-72-10a hs-72-10a containment spray pump b mtr sw ptlock hs-63-94a Hs-63-94a rhr to rcs cl1_4 flow control valve s open

b. Place the simulator in RUN momentarily, and acknowledge all alarms.
2. Place Hold Order on 1A CS Pump - handswitch is in PULL-TO-LOCK position
3. Place simulator in FREEZE until the applicant indicates an understanding of the task.
4. After applicant indicates understanding of the task, place simulator to RUN.

Tools/Equipment/Procedures Needed:

Ensure marked copies of FR-Z.1 are available to the evaluators.

REV. 6 PAGE 34 OF 131 WATTS BAR NUCLEAR PLANT B.1.d READ TO APPLICANT

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. 1A-A Containment Spray Pump has been tagged out of service.
2. The unit was at 100% when a Large Break LOCA occurred.
3. 1B-B Containment Spray Pump started and has been spraying containment.
4. The break occurred an hour and 10 minutes ago.
5. All ECCS equipment is performing it s design functions and is on Containment Sump Recirc.
6. You are the Operator at the Controls (OAC).

INITIATING CUES:

1. The Unit Supervisor directs you to perform FR-Z.1, "HIGH CONTAINMENT PRESSURE," Step 10, DETERMINE if RHR spray should be placed in service.
2. You are to notify the Unit Supervisor when you have completed Step 10.

REV. 6 PAGE 35 OF 131 WATTS BAR NUCLEAR PLANT B.1.d START TIME: _______

STEP 1: Obtain a copy of the procedure.

STANDARD: A copy of FR-Z.1 has been obtained.

EXAMINER'S CUE:

After the applicant has de monstrated the method of obtaining the correct instruction, the evaluator will

provide a marked-up copy of the instruction.

COMMENTS:

___ SAT

___ UNSAT STEP 2: [Step 10] DETERMINE if RHR Spray should be placed in service: a. CHECK the following conditions:

  • At least one hour elapsed since beginning of the accident.
  • Cntmt Press greater than 9.5 psig.
  • RHR suction aligned to the cntmt sump.
  • At least one charging pump and one SI pump running

STANDARD: 1. Applicant has determined that an hour has lapsed since the beginning of the accident. [Given in initial conditions]

2. Cntmt press has been checked > 9.5 psig.
3. FCV-63-72 and FCV-63-73 verified to be open by red indicating lights. 4. 1 CCP & 1 SIP verified to be running by indicating lights or amps.

COMMENTS:

___ SAT

___ UNSAT REV. 6 PAGE 36 OF 131 WATTS BAR NUCLEAR PLANT B.1.d STEP 3: [STEP 10b]

ALIGN Train B RHR spray:

1) ENSURE Train B RHR pump RUNNING.

STANDARD: Train B RHR pump verified to be running by indicating light or amps. COMMENTS:

___ SAT

___ UNSAT

STEP 4: [STEP 10b 2)] Close RHR crosstie 1-FCV-74-35.

STANDARD: 1-HS-74-35-A has been checked in the CLOSED position and the green light illuminated on HS.

COMMENTS:

___ SAT

___ UNSAT

STEP 5: [STEP 10b 3)] CLOSE RHR injection 1-FCV-63-94.

STANDARD: 1-HS-63-94-A has been placed in the CLOSED position and the Applicant recognizes that the GREEN light DOES NOT illuminate.

Applicant enters the RNO Column to perform actions to align Train A RHR spray. Step is critical since the RHR system is not designed to support both RHR spray and suction requirements associated with sump recirculation.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT EVALUATOR NOTE: Applicant may either have US dispatch personnel or will dispatch personnel to invest igate the cause of the failure of 1-FCV-63-94.

REV. 6 PAGE 37 OF 131 WATTS BAR NUCLEAR PLANT B.1.d STEP 6: [STEP 10b RNO] ALIGN Train A RHR spray: 1) ENSURE Train A RHR pump RUNNING.

STANDARD: Train A RHR pump verified to be running by indicating light or amps.

COMMENTS:

___ SAT

___ UNSAT STEP 7: [STEP 10b RNO] 2) CLOSE RHR crosstie 1-FCV-74-33.

STANDARD: 1-HS-74-33-A has been placed/checked in the CLOSED position and the green light illuminated on HS.

COMMENTS:

___ SAT

___ UNSAT

STEP 8: [STEP 10b RNO] 3) CLOSE RHR injection 1-FCV-63-93.

STANDARD: 1-HS-63-93-A has been placed in the CLOSED position and the green light illuminated on HS. Step is critical to establish A Train RHR Spray.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT STEP 9: [STEP 10b RNO]

4) OPEN RHR spray 1-FCV-72-40.

STANDARD: 1-HS-72-40A has been placed/checked in the OPEN position and the Red light illuminated on hand switch. Step is critical to establish A Train RHR Spray.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT REV. 6 PAGE 38 OF 131 WATTS BAR NUCLEAR PLANT B.1.d STEP 10: Notify the Unit Supervisor that RHR spray is in service.

STANDARD: Notify the Unit Supervisor that RHR spray has been placed in service. **CUE: When notified, acknowledge the report using repeat back.

COMMENTS:

END OF TASK

___ SAT

___ UNSAT

TIME STOP: ________

REV. 0 Page 39 of 131 WATTS BAR NUCLEAR PLANT B.1.e DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned

task. INITIAL CONDITIONS:

1. 1A-A Containment Spray Pump has been tagged out of service.
2. The unit was at 100% when a Large Break LOCA occurred.
3. 1B-B Containment Spray Pump started and has been spraying containment.
4. The break occurred an hour and 10 minutes ago.
5. All ECCS equipment is performing it s design functions and is on Containment Sump Recirc.
6. You are the Operator at the Controls (OAC).

INITIATING CUES:

1. The Unit Supervisor directs you to perform FR-Z.1, "HIGH CONTAINMENT PRESSURE", Step 10, DETERMINE if RHR spray should be placed in service.
2. You are to notify the Unit Supervisor when you have completed Step 10.

REV. 0 Page 40 of 131 WATTS BAR NUCLEAR PLANT B.1.e

B.1.e Place Containment Hydrogen Recombiner "A" in Service per SOI-83.01, "Containment Hydrogen Recombiners."

REV. 0 Page 41 of 131 WATTS BAR NUCLEAR PLANT B.1.e Task: Place Containment Hydrogen Recombiner A in Service per SOI-83.01,"Containment Hydrogen Recombiners."

Alternate Path:

N/A Facility JPM #: 3-OT-JPMR052.

K/A Rating(s):

028 Hydrogen Recombiner and Purge Control System. A2.01Hydrogen recombiner power setting, determined by using plant data book. [3.4/3.6] (CFR: 41.5 / 43.5 / 45.3 / 45.13).

Task Standard: Containment Hydrogen Recombiner A has been placed in service per SOI-83.01, "Containment Hydrogen Recombiners."

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __X__ In-Plant _____ Perform __X___ Simulate ___ _

References

E-1, "Loss of Reactor or Secondary Coolant," Rev. 15. SOI-83.01, "Containment Hydrogen Recombiners," Rev. 15. TI-83.01,"Hydrogen Recombiner Required Power-vs.-Containment Pressure Curves," Rev. 1.

Task Number: RO-063-SOI-63-003 APPLICABLE FOR: RO/SRO 10CFR55.45: 5, 6 Validation Time: 15 min.

Time Critical:

No ===========================================================================

Applicant: ___________________________ _________________ Time Start: ________

NAME SSNTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 0 Page 42 of 131 WATTS BAR NUCLEAR PLANT B.1.e REV. 0 Page 43 of 131 WATTS BAR NUCLEAR PLANT B.1.e SIMULATOR OPERATOR INSTRUCTIONS:

1. Initialize to IC 315. a. Ensure the following items are displayed on the Director Summary Page:

th03a loca-small leak loop 1 100% severity th01a loca-hot leg loop 1 4.5% severity mux_03c123 125-a cntmt hi-hi press steamline isol on pi-30-310 03110 containment pressure 3.5 pi-30-311 03120 containment pressure 3.5 h2i-43-200 03060 loca h2 cntmt monitor 3.5 h2i-43-210 03070 loca h2 cntmt monitor 3.5 pdi-30-42 03160 cntmt press diff indicator 4 pdi-30-43 03170 cntmt press diff indicator 4 pdi-30-44 03180 cntmt press diff indicator 4 pdi-30-45 03190 cntmt press diff indicator 4

b. Place the simulator in RUN momentarily, and acknowledge all alarms.
2. Place simulator in FREEZE until the applicant indicates an understanding of the task.
3. After applicant indicates understanding of the task, place simulator to RUN.

Tools/Equipment/Procedures Needed:

Ensure copies of SOI-83.01 "Containment Hydrogen Recombiners," and TI-83.01 , "Hydrogen Recombiner Required Power-vs.-Containment Pressure."

REV. 0 Page 44 of 131 WATTS BAR NUCLEAR PLANT B.1.e READ APPLICANT

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit has experienced a LOCA.
2. MCR crew is implementing E-1, "Loss of Reactor or Secondary Coolant."
3. E-1, directs that the hydrogen recombiners be placed in service using SOI-83.01, "Containment Hydrogen Recombiners."
4. You are the Control Room Operator.

INITIATING CUES:

1. The Unit Supervisor has directed you to place Hydrogen Recombiner "A" in service, using SOI-83.01, Containment Hydrogen Recombiners."
2. Notify the Unit Supervisor when the required power setting is reached.

REV. 0 Page 45 of 131 WATTS BAR NUCLEAR PLANT B.1.e START TIME: _______

STEP 1: Obtain a copy of the procedure.

STANDARD: Obtains SOI-83.01 and goes to Section 8.1.

EXAMINER'S CUE:

After the applicant has de monstrated the method of obtaining the correct instruction, the evaluator can

provide a copy of the instruction.

COMMENTS:

___ SAT

___ UNSAT CAUTION 1 Temperature of 1400°F is not to be exceeded on any operable thermocouple. CAUTION 2 On DG power, DG load should remain 4400 kW or less.

CAUTION 3 If there is any indication Recombiner A is not operating properly (through recombiner instrumentation), the Recombiner should be shutdown, a WR written, and the other Recombiner placed in service.

NOTE: TI-83.01, "HYDROGEN RECOMBINER REQUIRED POWER-VS-CONTAINMENT PRESSURE" contains the curves that will be needed to adjust the power level for the recombiner.

STEP 2: [1] ENSURE POWER ADJUST potentiometer [1-M-10] set at 000.

STANDARD: Applicant verifies that three zeros ("000") are indicated on Panel 1-M-10.

COMMENTS:

___ SAT

___ UNSAT REV. 0 Page 46 of 131 WATTS BAR NUCLEAR PLANT B.1.e STEP 3: [2] VERIFY the White POWER IN AVAILABLE light LIT.

STANDARD: Applicant verifies that the White POWER IN AVAILABLE light LIT on 1-M-10.

COMMENTS:

___ SAT

___ UNSAT STEP 4: [3] ENSURE TEMPERATURE CHANNEL (thermocouple selector) is selected for channel 1, 2, or 3.

STANDARD: Applicant verifies that the TEMPERATURE CHANNEL (thermocouple selector) is selected for channel 1, 2, or 3.

COMMENTS:

___ SAT

___ UNSAT STEP 5: [4] ENSURE TEMPERATURE OUT (indicator dial), set on 1400°F.

STANDARD: Applicant verifies that the TEMPERATURE OUT (indicator dial), set on 1400°F.

COMMENTS:

___ SAT

___ UNSAT NOTE: Red light on TEMPERATURE OUT (indicator dial) is lit when setpoint selected on indicator is reached.

REV. 0 Page 47 of 131 WATTS BAR NUCLEAR PLANT B.1.e STEP 6: [5] REQUEST Chemistry to sample containment atmosphere for H2 concentration.

STANDARD: Applicant contacts Chemistry to sample containment atmosphere.

EVALUATOR CUE: Containment atmosphere has been sampled and the hydrogen concentration is 3.5%.

COMMENTS:

___ SAT

___ UNSAT STEP 7: [6] RECORD the Date and Time on Data Sheet 1.

STANDARD: Applicant records Date and Time on Data Sheet 1

COMMENTS:

___ SAT

___ UNSAT REV. 0 Page 48 of 131 WATTS BAR NUCLEAR PLANT B.1.e STEP 8: [7] RECORD CNTMT H2 % on Data Sheet 1, THEN INDICATE from which source H2 percentage was obtained:

[7.1] ANAL A CNTMT H2,1-H21-43-200 [1-M-10]

[7.2] ANAL B CNTMT H2 , 1-H21 210 [1-M-10]

[7.3] Chemistry sample analysis STANDARD: Applicant has data available from each of the sources and may enter a value for any of them. The containment hydrogen concentration is 3.5%.

COMMENTS:

___ SAT

___ UNSAT STEP 9: [8] IF containment H2 is greater than 5%, THEN DO NOT place H2 Recombiner in service, and NOTIFY the SM.

STANDARD: Applicant confirms that hydrogen concentration is less than 5% and enters N/A for this step.

COMMENTS:

___ SAT

___ UNSAT REV. 0 Page 49 of 131 WATTS BAR NUCLEAR PLANT B.1.e STEP 10: [9] RECORD CNTMT PRESS (psig) on Data Sheet 1, THEN INDICATE which indicator was used:

[9.1] 1-PI-30-310, CNTMT WR PRESS [1-M-9]

[9.2] 1-PI-30-311, CNTMT WR PRESS [1-M-9]

STANDARD: Applicant enters a value of 3 psig for either pressure indicator.

COMMENTS:

___ SAT

___ UNSAT STEP 11: [10] TURN POWER OUT (MS Starter) switch to ON, and VERIFY switch plate Red light LIT.

STANDARD: Applicant places switch in the UP position, and verifies the RED light is LIT. Step is critical since this action provides power to the recombiner.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT STEP 12: [11] ADJUST POWER ADJUST potentiometer clockwise to obtain 5 kW on POWER OUT meter, and MAINTAIN for 10 minutes.

STANDARD: Applicant adjusts the potentiometer and obtains 5 kW on the POWER OUT meter. Step is critical to warm up the recombiner.

EVALUATOR CUE: Time Compression - 10 minutes have elapsed.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT REV. 0 Page 50 of 131 WATTS BAR NUCLEAR PLANT B.1.e STEP 13: [12] ADJUST POWER ADJUST potentiometer to obtain 10 kW on POWER OUT meter, and MAINTAIN for 10 minutes.

STANDARD: Applicant adjusts the potentiometer and obtains 10 kW on the POWER OUT meter. Step is critical to warm up the recombiner.

EVALUATOR CUE: Time Compression - 10 minutes have elapsed.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT STEP 14: [13] ADJUST POWER ADJUST potentiometer to obtain 20 kW on POWER OUT meter, and MAINTAIN for 5 minutes.

STANDARD: Applicant adjusts the potentiometer and obtains 20 kW on the POWER OUT meter. Step is critical to warm up the recombiner.

EVALUATOR CUE: Time Compression - 5 minutes have elapsed.

COMMENTS:

___ SAT

___ UNSAT STEP 15: [14] DETERMINE the REQUIRED POWER (kW) based on current CNTMT PRESSURE (psig) using Attachment 3 of TI-83.01, HYDROGEN RECOMBINER REQUIRED POWER-VS-CONTAINMENT PRESSURE CURVES.

STANDARD: Applicant uses 3 psig containment pressure and reads 70 kW off the Attachment 3 curve in TI-83.01, HYDROGEN RECOMBINER REQUIRED POWER-VS-CONTAINMENT PRESSURE CURVES.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT REV. 0 Page 51 of 131 WATTS BAR NUCLEAR PLANT B.1.e STEP 16: [15] ADJUST POWER ADJUST potentiometer to obtain the REQUIRED POWER (kW) using Attachment 3 of TI- 83.01, HYDROGEN RECOMBINER REQUIRED POWER-VS-CONTAINMENT PRESSURE CURVES.

STANDARD: Applicant adjusts the potentiometer and obtains 70 kW on the POWER OUT meter. Step is critical to warm up the recombiner.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT NOTES 1) Periodic potentiometer adjustment is necessary to maintain Required Power setting. Temperature is obtained by selecting an average temperature of all operable thermocouples. Temperature should rise to 1150-1400°F in approximately 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> depending on initial containment temperature. 2) Recombiner temperature should be allowed to stabilize before making power changes due to the lag time between adjustment and actual temperature change.

3) 1 kW power change is approximately equal to 20°F recombiner temperature change.

STEP 17: [16] AFTER recombiner temperature has stabilized for approximately 30 minutes, THEN ADJUST POWER ADJUST potentiometer to maintain 1225 - 1400°F recombiner average temperature.

STANDARD: EVALUATOR CUE: Time Compression - 30 minutes have elapsed, and another operator will make adjustments to maintain temperature between 1225 - 1400°F.

COMMENTS:

___ SAT

___ UNSAT REV. 0 Page 52 of 131 WATTS BAR NUCLEAR PLANT B.1.e STEP 18: [17] NOTIFY SRO that Recombiner A is in service and will be monitored at least once every 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> per Section 8.2.

STANDARD: Applicant notifies the SRO that "A" Recombiner is in service.

COMMENTS:

END OF TASK

___ SAT

___ UNSAT STOP TIME _____

REV. 6 PAGE 53 OF 131 WATTS BAR NUCLEAR PLANT B.1.f DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit has experienced a LOCA.
2. MCR crew is implementing E-1, "Loss of Reactor or Secondary Coolant."
3. E-1, directs that the hydrogen recombiners be placed in service using SOI-83.01, "Containment Hydrogen Recombiners."
4. You are the Control Room Operator.

INITIATING CUES:

1. The Unit Supervisor has directed you to place Hydrogen Recombiner "A" in service, using SOI-83.01, Containment Hydrogen Recombiners."
2. Notify the Unit Supervisor when the required power setting is reached.

REV. 6 PAGE 54 OF 131 WATTS BAR NUCLEAR PLANT B.1.f

B.1.f Synchronizing DG 1B-B from the MCR per SOI-82.02, "Diesel Generator (D/G) 1B-B."

REV. 6 PAGE 55 OF 131 WATTS BAR NUCLEAR PLANT B.1.f EVALUATION SHEET Task: Synchronizing DG 1B-B from the MCR per SOI-82.02 "Diesel Generator (D/G) 1B-B."

Alternate Path:

N/A Facility JPM #: 3-OT-JPMR060 K/A Rating(s):

064 Emergency Diesel Generators. A1.03 Ability to predict and/or monitor changes in parameters (to prevent exceeding design limits) associated with operating the ED/G system controls including: Operating voltages, currents, and temperatures

[3.2/3.3] (CFR: 41.5 / 45.5) 064 Emergency Diesel Generators. A4.06 Ability to manually operate and/or monitor in the control room: Manual start, loading, and stopping of the ED/G [3.9/3.9]

(CFR: 41.7 / 45.5 to 45.8)

Task Standard: 1B-B Diesel Generator is synchronized to the shutdown board from the MCR, per SOI-82.02 Section 8.1.4, and then loaded to 4 MW and 0.74-1.25 MVARs.

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __X__ In-Plant __ ___ Perform __X____ Simulate ____

References

SOI-82.02, "Diesel Generator (D/G) 1B-B" Rev. 65

Task Number: RO-082-SOI-82-002 APPLICABLE FOR: RO/SRO RO-082-SOI-82-008 RO-082-SOI-82-010 10CFR55.45

3, 4, 6, 8

Validation Time: 18 min.

Time Critical: No ===========================================================================

Candidate: ___________________________ _________________ Time Start: ________

NAME SSN/IDTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 6 PAGE 56 OF 131 WATTS BAR NUCLEAR PLANT B.1.f REV. 6 PAGE 57 OF 131 WATTS BAR NUCLEAR PLANT B.1.f SIMULATOR OPERATOR INSTRUCTIONS:

1. Initialize to IC # 316. NOTE: If this JPM is to be run concurrently with B.1.b, Place Excess Letdown in service, then reset to IC # 312.
2. 1B-B Diesel Generator is running unloaded, after an idle start.
3. Place the simulator in RUN momentarily, and acknowledge all alarms.
4. Place simulator in FREEZE until the Applicant indicates an understanding of the task.
5. After applicant indicates understanding of the task, place simulator to RUN.

Tools/Equipment/Procedures Needed:

Ensure a marked-up copy of SOI-82.02, "Diesel Generator (D/G) 1B-B" is available to provide to each applicant. Stop Watch, to time Synchroscope rotation.

REV. 6 PAGE 58 OF 131 WATTS BAR NUCLEAR PLANT B.1.f READ TO OPERATOR

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit is at 100% power.
2. Testing is being conducted on 1B-B diesel generator. It is to be paralleled to the shutdown board for a Factory Representative on site.
3. The 1B-B DG is running at rated speed , after performance of SOI-82.02, "Diesel Generator (D/G) 1B-B," Section 8.1.3 Idle Speed to Rated Speed.
4. You are an extra control room operator on shift.

INITIATING CUES:

1. The Unit Supervisor directs you to parallel the 1B-B diesel generator to the 1B-B Shutdown Board per SOI-82.02, "Diesel Generator (D/G) 1B-B" and load it to 4 MWs.
2. SOI-82.02, "Diesel Genera tor (D/G) 1B-B," Section 8.1.4 Steps 1 through 3 have been performed.
3. You are to inform the Unit Supervisor when the diesel generator is loaded to 4 MWs.

REV. 6 PAGE 59 OF 131 WATTS BAR NUCLEAR PLANT B.1.f START TIME: _______

STEP 1: Obtain a copy of the instruction.

STANDARD: A copy of SOI-82.02 Section 8.1.4 has been obtained.

EXAMINER'S CUE:

After the applicant has demonstrated the method of obtaining the correct instruction, the evaluator can provide a copy of the instruction.

COMMENTS:

___ SAT

___ UNSAT STEP 2: [4] PLACE 1-HS-82-48, DG MODE SELECTOR, in PARALLEL. [0-M-26].

STANDARD: 1-HS-82-48, DG MODE SELECTOR, is placed in PARALLEL. This step is critical for task performance to allow proper operation of voltage regulator & DG speed droop circuits.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT

REV. 6 PAGE 60 OF 131 WATTS BAR NUCLEAR PLANT B.1.f STEP 3: [5] ENSURE the following sync switches for 1B-B D/G in OFF. NOMENCLATURE LOCATION POSITION UNID MAINTENANCE 6.9 UNIT BD 1C SYNC SWITCH 0-M-26 OFF 1-HS-57-69 ALTERNATE CSST C SYNC SWITCH 0-M-26 OFF 1-HS-57-115 DG SYNC SWITCH 0-M-26 OFF 1-HS-57-74 NORMAL-CSST D SYNC SWITCH 0-M-26 OFF 1-HS-57-72 STANDARD: Applicant checks listed sync switches in OFF position COMMENTS:

___ SAT

___ UNSAT

STEP 4: [6] PLACE 1-HS-57-74, DG SYNC SWITCH, to SYN.

STANDARD: 1-HS-57-74, DG SYNC SWITCH, is placed to SYN position.

This step is critical to allow synchronization of D/G to 1B-B Shutdown board.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT CAUTION: When adjusting speed and voltage care must be taken to prevent overshooting desired values. Voltage control response is approximately five times faster than speed control response.

REV. 6 PAGE 61 OF 131 WATTS BAR NUCLEAR PLANT B.1.f STEP 5: [7] MATCH generator Incoming Frequency (1-XI-82-32) with Running Frequency (1-XI-82-33) using 1-HS-82-43, SPEED CONTROL [0-M-26].

STANDARD: 1-HS-82-43 is used to adjust generator frequency (incoming) on 1-XI-82-32 to match with board frequency (running) on 1-XI-82-33. This step is critical to allow synchronization of D/G to 1B-B Shutdown board.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT STEP 6: [8] MATCH generator Incoming Voltage, (1-EI-82-34) with Running Voltage (1-EI-82-35) using 1-HS-82-42, VOLTAGE REGULATOR [0-M-26].

STANDARD: 1-HS-82-42 is used to adjust generator voltage on 1-EI-82-34 to match with board voltage on 1-EI-82-35. This step is critical to allow synchronization of D/G to 1B-B Shutdown board.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT REV. 6 PAGE 62 OF 131 WATTS BAR NUCLEAR PLANT B.1.f STEP 7: [9] ENSURE DG Frequency and Voltage are MATCHED with 6.9 kV SD Bd, AND ADJUST 1-HS-82-43, SPEED CONTROL, [0-M-26] to obtain desired clockwise rotation (15 or more seconds) on 1-XI-82-31, TRAIN 1B-B SYNCHROSCOPE.

STANDARD: Applicant verifies running and incoming frequency and voltage are matched and that the synchroscope is moving slowly in the clockwise direction at 15 seconds or more per rotation on the scope. This step is critical to ensure proper DG synchronization that is performed in the next step. NOTE TO EVALUATOR: The applicant may use a stopwatch to time the 15 second rotation.

Provide stopwatch if asked.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT NOTES 1) Steps 8.1.4[10] through 8.1.4[11.3] may be signed off after completion of Step 8.1.4[11.3] 2) Peer checking required on the next step

REV. 6 PAGE 63 OF 131 WATTS BAR NUCLEAR PLANT B.1.f STEP 8: [10] WHEN TRAIN 1B-B SYNCHROSCOPE (1-XI-82-31) reaches 12 o'clock, THEN TURN 1-HS-57-73A, 1914 - DG TO SD 1B-B, to CLOSE.

STANDARD: ACB 1914, DG TO SD 1B-B, is closed with 1-HS-57-73A, when the synchroscope reaches 12 o'clock. This step is critical to ensure proper DG synchronization onto 1B-B Shutdown Board.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT NOTE Maintain outgoing VARS by periodically adjusting voltage regulator with 1-HS-82-42 while loading DG. Controls should not be operated simultaneously.

STEP 9: [11] PERFORM the following: [11.1] LOAD DG promptly using 1-HS-82-43, SPEED CONTROL to at least 1.1 Megawatts as indicated on 1-EI-82-40A, DG MEGAWATTS (0-M-26).

STANDARD: The generator output is increased to 1.1 MW on 0-EI 40A. This step is critical to ensure proper DG loading and avoid reverse power trip.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT REV. 6 PAGE 64 OF 131 WATTS BAR NUCLEAR PLANT B.1.f NOTE DG MEGAVARs may "swing" when the 6.9 KV automatic tap changers engage to stabilize the voltage in the system.

STEP 10: [11.2] PERFORM the following:

[b] MAINTAIN DG MEGAVARS 0.75 to 1.25 OUTGOING on 1-EI-82-41A, with 1-HS-82-42, VOLTAGE REGULATOR.

STANDARD: The generator megavars is adjusted to between 0.75 and 1.25 Megavars on 0-EI-82-41A.

COMMENTS:

___ SAT

___ UNSAT CAUTION Operation of the DG at load of 2.7 MW or less for extended period of time may lead to exhaust fire.

STEP 11: [11.3] PERFORM the following: [c] RAISE load to at least 3.3 Megawatts.

STANDARD: The generator output is raised to >2.7 MW on 0-EI-82-40A.

This step is to ensure DG is loaded per task assignment, and the information in the CAUTION is complied with.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT REV. 6 PAGE 65 OF 131 WATTS BAR NUCLEAR PLANT B.1.f STEP 12: [11.4] PLACE 1-HS-57-74, DG SYNC SWITCH, to OFF.

STANDARD: 1-HS-57-74, DG SYNC SWITCH, is placed to OFF

COMMENTS:

___ SAT

___ UNSAT STEP 13: [11.5] MAINTAIN DG operation for a minimum of one hour, OR until engine temperatures stabilize.

STANDARD: Applicant reecognizes that the DG must be run for a minimum of 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br />, OR until engine temperatures stabilize.

EVALUATOR CUE: If asked, state temperatures will be monitored locally until they stabilize.

COMMENTS:

___ SAT

___ UNSAT STEP 14: Notify the Unit Supervisor that DG 1B-B is synchronized to the shutdown board and loaded to 4 MW.

STANDARD: The Unit Supervisor is notified that DG 1B-B is synchronized to the shutdown board and loaded to 4 MW.

CUE: As Unit Supervisor, wh en notified, acknowledge the report.

COMMENTS:

END OF TASK

___ SAT

___ UNSAT TIME STOP: ________

REV. 2 PAGE 66 OF 131 WATTS BAR NUCLEAR PLANT B.1.g DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit is at 100% power.
2. Testing is being conducted on 1B-B diesel generator. It is to be paralleled to the shutdown board for a Factory Rep. on site.
3. The 1B-B DG is running at rated speed , after performance of SOI-82.02, "Diesel Generator (D/G) 1B-B," Section 8.1.3 Idle Speed to Rated Speed.
4. You are an extra control room operator on shift.

INITIATING CUES:

1. The Unit Supervisor directs you to parallel the 1B-B diesel generator to the 1B-B Shutdown Board per SOI-82.02, "Diesel Generator (D/G) 1B-B" and load it to 4 MWs.
2. SOI-82.02, "Diesel Genera tor (D/G) 1B-B," Section 8.1.4 Steps 1 through 3 have been performed.
3. You are to inform the Unit Supervisor when the diesel generator is loaded to 4 MWs.

REV. 2 PAGE 67 OF 131 WATTS BAR NUCLEAR PLANT B.1.g

ALTERNATE PATH B.1.g Return PRM N-42 to Service per AOI-4, "NUCLEAR INSTRUMENTATION MALFUNCTIONS."

REV. 2 PAGE 68 OF 131 WATTS BAR NUCLEAR PLANT B.1.g Task: Return PRM N-42 to Service per AOI-4 Alternate Path:

When rod control is returned to auto a continuous rod insertion occurs requiring applicant to return rod control to manual and then a trip of the reactor. Facility JPM #: 3-OT-JPMR108A Rev 0 K/A Rating(s):

015 Nuclear Instrumentation System. A4.02 A4 Ability to manually operate and/or monitor in the control room: NIS indicators. [3.9/3.9] (CFR: 41.7 / 45.5 to 45.8).

Task Standard: The DETECTOR CURRENT COMPARATOR switch for UPPER SECTION, the DETECTOR CURRENT COMPARATOR switch for LOWER SECTION, the ROD STOP BYPASS, the POWER MISMATCH BYPASS, and the COMPARATOR CHANNEL DEFEAT have been placed in NORMAL or OPERATE as directed AOI-4, and then reactor is manually tripped due to continuous rod insertion.

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __X__ In-Plant _____ Perform __X___ Simulate ___ _

References

AOI-4, "NUCLEAR INSTRUMENTATION MALFUNCTIONS," Rev 28 AOI-2, "MALFUNCTION OF REACTOR CONTROL SYSTEM," Rev 37 Task Number: RO-092-AOI-4-002 APPLICABLE FOR: RO/SRO RO-085-AOI-2-005 10CFR55.45: 2, 3, 4, 5, 6, 12 Validation Time: 12 min.

Time Critical:

No ===========================================================================

Applicant: ___________________________ _________________ Time Start: ________

NAME SSN/EINTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 2 PAGE 69 OF 131 WATTS BAR NUCLEAR PLANT B.1.g SIMULATOR OPERATOR INSTRUCTIONS:

1. Initialize to IC 317. a. Ensure the following items are displayed on the Director Summary Page:

rd02 Uncontrolled rod insertion, bank d, group 2 100% severity

b. Ensure the switches on 1-M-13 to the "N42" position to defeat Power Range Channel N42 inputs per AOI-4, Attachment 1, and Step 1 a. through f.
c. Place the simulator in RUN momentarily, and acknowledge all alarms.
2. Load NRC_Exam_Event_Files.evt from the NRC Exam Flash Drive. The malfunction will be entered when Rod Control Selector Switch is placed in AUTO (Event 23).
3. Place simulator in FREEZE until the applicant indicates an understanding of the task.
4. After Applicant indicates understanding of the task, place simulator to RUN.

Tools/Equipment/Procedures Needed:

Ensure a marked-up copy of AOI-4 is available to the Evaluator and clean copies of AOI-2 in all copies of Abnormal Operating Instructions on the Simulator Floor.

REV. 2 PAGE 70 OF 131 WATTS BAR NUCLEAR PLANT B.1.g READ TO APPLICANT

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit 1 is at 100% power.
2. Power Range Monitor N42 failed during last shift.
3. AOI-4 "NUCLEAR INSTRUMENTATION MALFUNCTIONS," Section 3.4. "Power Range Monitor (PRM) Failure," has been completed through Step 16.a.
4. Work Control has notified the MCR that repairs to PRM N42 are complete and the instrument is ready to be returned to service.
5. You are the Operator at the Controls.

INITIATING CUES:

1. The Unit Supervisor has directed you to return PRM N42 to service.
2. You are to notify the US when the control rods have been returned to AUTO.

REV. 2 PAGE 71 OF 131 WATTS BAR NUCLEAR PLANT B.1.g START TIME: _______

STEP 1: Obtain the correct procedure.

STANDARD: A copy of AOI-4 has been obtained.

EXAMINER'S CUE:

After the applicant has de monstrated the method of obtaining the correct instruction, the evaluator will

provide a marked-up copy of the instruction.

COMMENTS:

___ SAT

___ UNSAT CAUTION Allowing at least 5 minutes between any rod control input (i.e., T-avg, T-ref, or NIS) change and placing rods in AUTO, will help prevent undesired control rod movement.

STEP 2: [Step 16b]

REFER TO Attachment 1, PRM Function At NIS Rack, step 2.

STANDARD: Applicant refers to Attachment 1, PRM Function At NIS Rack, Step 2 for restoration of PRM N42.

COMMENTS:

___ SAT

___ UNSAT REV. 2 PAGE 72 OF 131 WATTS BAR NUCLEAR PLANT B.1.g NOTE TO EVALUATOR: The following steps are from Attachment 1 page 2 of 2, AOI-4.

STEP 3: [STEP 2] WHEN PRM is ready for return to service , THEN PERFORM the following steps:

a. PLACE DETECTOR CURRENT COMPARATOR switch for UPPER SECTION in NORMAL STANDARD: Detector Current Comparator Upper Section switch placed to "NORMAL" (Miscellaneous Control & Indication Panel,1-IDWR-92-N50-G IV)

Step is critical for proper restoration of upper power detector to current comparator.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT

STEP 4: [STEP 2 b]

PLACE DETECTOR CURRENT COMPARATOR switch for LOWER SECTION in NORMAL

STANDARD: Detector Current Comparator Lower Section switch placed to "NORMAL" (Miscellaneous Control & Indication Panel, 1-IDWR-92-N50-G IV).

Step is critical for proper restoration of lower power detector to current comparator.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT REV. 2 PAGE 73 OF 131 WATTS BAR NUCLEAR PLANT B.1.g NOTE: On the following step, annunciator window 66-C, 67-C, 68-C, OR 69-C, N-(#) OVERPOWER ROD STOP BYPASSED, will clear depending on which channel is bypassed.

STEP 5: [STEP 2 c]

PLACE ROD STOP BYPASS switch in OPERATE.

STANDARD: Rod Stop Bypass switch is positioned from "N42" to "OPERATE" (Miscellaneous Control & Indication Panel,1-IDWR-92-N50-G IV)

Step is critical for proper restoration of to enable rod stop

interlock protection from this channel.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT STEP 6: [STEP 2 d]

PLACE POWER MISMATCH BYPASS switch in OPERATE.

STANDARD: Power Mismatch Bypass switch is positioned from "N42" to "OPERATE" (Miscellaneous Control & Indication Panel, 1-IDWR-92-N50-G IV)

Step is critical to rest ore channel input to high auctioneering circuit and power mismatch circuits.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT

REV. 2 PAGE 74 OF 131 WATTS BAR NUCLEAR PLANT B.1.g NOTE: On the following step, annunciator window 82-E, NIS CHANNEL IN TEST, will clear.

STEP 7: [STEP 2 e]

PLACE COMPARATOR CHANNEL DEFEAT switch in NORMAL.

STANDARD: Comparator Channel Defeat Switch is positioned to "NORMAL" (Comparator & Rate Panel, Comparator N37, 1-IDWR-92-N37 IV). Step is critical to restor e channel input to channel comparator alarm circuits.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT

NOTE: On the following step, annunciator window 115-E, POWER RANGE FLUX RATE HI, will clear if the positive rate trip light is LIT.

STEP 8: [STEP 2 f]

IF POSITIVE RATE TRIP is LIT, THEN RESET RATE MODE switch.

STANDARD: Positive Rate Trip light on Power Range Upper N42A, 1-IDWR-92-42A II, is checked and determines light is NOT LIT and continues to next step.

COMMENTS:

___ SAT

___ UNSAT

REV. 2 PAGE 75 OF 131 WATTS BAR NUCLEAR PLANT B.1.g NOTE TO EVALUATOR: Applicant returns to AOI-4 at step 16 c.

STEP 9: [STEP 16 c]

ENSURE T-avg and T-ref within 1

°. STANDARD: Applicant verifies T-avg and T-ref within 1

° by recorder 1-TR-68-2B on 1-M-5 or other T-avg - T-ref indications.

COMMENTS:

___ SAT

___ UNSAT

STEP 10: [STEP 16 d] ENSURE zero demand on control rod position indication [1-M-4].

STANDARD: Applicant determines zero demand on control rod position indication CERPI display or ICS computer display for CERPI

  • CERPI Display
  • Plant computer

COMMENTS:

___ SAT

___ UNSAT REV. 2 PAGE 76 OF 131 WATTS BAR NUCLEAR PLANT B.1.g STEP 11: [STEP 16 e]

IF auto rod control desired, PLACE control rods in AUTO.

STANDARD: The rod control hand switch has been placed in AUTO position.

    • CUE: If asked, respond as US that auto rod control is desired.

NOTE TO EVALUATOR: Continuous rod insertion malfunction is inserted when rod control is placed in AUTO. The applicant may immediately return rod control to manual, check for rod motion stopped, and then trip the reactor before referring to AOI-2.

COMMENTS:

___ SAT

___ UNSAT

NOTE TO EVALUATOR: The Following Steps are from AOI-2 Section 3.2 due to continuous rod insertion.

STEP 12: [STEP 1] PLACE control rods in MAN.

STANDARD: Rod control hand switch has been placed in Manual position.

NOTE: Rods will continue to step IN.

COMMENTS:

___ SAT

___ UNSAT

REV. 2 PAGE 77 OF 131 WATTS BAR NUCLEAR PLANT B.1.g STEP 13: [STEP 2] CHECK control rod movement STOPPED.

STANDARD: Rod control indications have been checked for movement and applicant determines that rods are still inserting and goes to RNO for step.

    • NOTE: Rods will continue to step IN.

COMMENTS:

___ SAT

___ UNSAT

STEP 14: [STEP 2 RNO]

TRIP reactor.

GO TO E-0, Reactor Trip or Safety Injection.

STANDARD: Reactor Trip hand switch on 1-M-4 or 1-M-6 has been placed to the TRIP position. Applicant than goes to E-0.

Critical step, as uncontrolled rod movement in manual rod control requires a reactor trip.

    • CUE: Upon transition to E-O, inform applicant "This completes this JPM."

COMMENTS:

END OF TASK CRITICAL STEP

___ SAT

___ UNSAT

TIME STOP: ________

REV. 0 PAGE 78 OF 131 WATTS BAR NUCLEAR PLANT B.1.h DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit 1 is at 100% power.
2. Power Range Monitor N42 failed during last shift.
3. AOI-4 "NUCLEAR INSTRUMENTATION MALFUNCTIONS," Section 3.4. "Power Range Monitor (PRM) Failure," has been completed through Step 16.a.
4. Work Control has notified the MCR that repairs to PRM N42 are complete and the instrument is ready to be returned to service.
5. You are the Operator at the Controls.

INITIATING CUES:

1. The Unit Supervisor has directed you to return PRM N42 to service.
2. You are to notify the US when the control rods have been returned to AUTO.

REV. 0 PAGE 79 OF 131 WATTS BAR NUCLEAR PLANT B.1.h

B.1.h Shutdown "A" Train EGTS Following a 10 Hour Run per SOI-65.02.

REV. 0 PAGE 80 OF 131 WATTS BAR NUCLEAR PLANT B.1.h Task: Shutdown "A" Train EGTS Following a 10 Hour Run per SOI-65.02, "Emergency Gas Treatment System."

Alternate Path:

N/A Facility JPM #: 3-OT-JPMR169 K/A Rating(s):

027 Containment Iodine Removal System (CIRS) A4.01, Ability to manually operate and/or monitor in the control room CIRS controls. [3.3*/3.3*] (CFR: 41,7/45.5/to 45.8) 029 Containment Purge System (CPS) A1.05 Knowledge of the physical connections and/or cause and effect relationships between the Containment Purge System and the containment air cleanup and recirculartion system. [2.9/3.1] (CFR:

41.2 to 41.9/45.7 to 45.8)

Task Standard: EGTS "A" Train has been shutdown and returned to Standby alignment in accordance with SOI-65.02 "Emergency Gas Treatment System."

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __X__ In-Plant _____ Perform __X___ Simulate ___ _

References

SOI-65.02 "Emergency Gas Treatment System" Rev. 24 Task Number: RO-065-SOI-65-005 APPLICABLE FOR: RO/SRO 10CFR55.45: 3, 6, 8 Validation Time: 15 min.

Time Critical:

No ===========================================================================

Applicant: ___________________________ _________________ Time Start: ________

NAME SSNTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 0 PAGE 81 OF 131 WATTS BAR NUCLEAR PLANT B.1.h REV. 0 PAGE 82 OF 131 WATTS BAR NUCLEAR PLANT B.1.h SIMULATOR OPERATOR INSTRUCTIONS:

1. Initialize to IC 318. 2. Ensure the alignment for "A" Train EGTS in service:

1-FCV-65 Open.

1-FCO-65 Open.

1-HS-65-81/86 - OPEN 1-HS-65-83/87 in A-AUTO STANDBY 0-HS-65-23A - RUNNING.

3. Acknowledge all alarms.
5. Freeze simulator until the applicant indicates understanding of the task and time is allowed for control board familiarization.
5. After applicant indicates understanding of task, place simulator in run.

Tools/Equipment/Procedures Needed:

Ensure clean copy of SOI-65.02 "Emergency Gas Treatment System" in all JPM packages.

REV. 0 PAGE 83 OF 131 WATTS BAR NUCLEAR PLANT B.1.h READ TO APPLICANT

DIRECTION TO APPLICANT I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit 1 is at 100% power.
2. 0-SI-65-6-A "Emergency Gas Treatment System Train A 10-Hour Operation" performance in progress.
3. "A" Train EGTS Fan has been in service for 10 hours1.157407e-4 days <br />0.00278 hours <br />1.653439e-5 weeks <br />3.805e-6 months <br />.
4. You are a support operator in the control room.

INITIATING CUES:

1. The Unit Supervisor directs you to shutdown the "A" Train EGTS Fan per SOI-65.02 and return EGTS to Standby Alignment per the procedure.
2. You are to notify Unit Supervisor when you have completed the task.

REV. 0 PAGE 84 OF 131 WATTS BAR NUCLEAR PLANT B.1.h START TIME: _______

STEP 1: Obtain a copy of the procedure.

STANDARD: A copy of SOI-65.02 section 7.1 has been obtained.

EXAMINER'S CUE:

After the applicant has de monstrated the method of obtaining the correct instruction, the evaluator provides a copy of the instruction.

NOTE TO EVALUATOR: Applicant may also identify Section 5.0 as needed to return EGTS to standby. You may provide a copy of this section when applicant seeks to obtain a copy.

COMMENTS:

___ SAT

___ UNSAT CAUTION: If EGTS is in service due to an accident signal initiation, and the charcoal filter banks have decay heat, an engineering evaluation must be performed before shutting down the EGTS system.

NOTE If EGTS was Auto actuated, both Trains' shutdown sections must be performed prior to return to standby readiness.

STEP 2: [Step 1] ENSURE a ØA Cntmt Isolation signal is NOT present.

STANDARD: Applicant determines that ØA Cntmt Isolation signal is NOT present by checking Master Isol Signal PNLs 1-XX-55-6C & 6D

ØA light DARK.

COMMENTS:

___ SAT

___ UNSAT REV. 0 PAGE 85 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 3: [Step 2] Momentarily PLACE 0-HS-65-23A, EGTS FAN & DISCH DMPR, in STOP (returns to A-AUTO).

STANDARD: Applicant stops "A" Train EGTS Fan with 0-HS-65-23A and checks red light off and green light ON the associated handswitch.

Step is critical to shutdown the running EGTS Fan.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT STEP 4: [Step 3] ENSURE 1-FCV-65-8, EGTS TR-A U1 SUCT DMPR, CLOSED.

STANDARD: Applicant checks 1-HS-65-8 and verifies red light off and green light ON for the associated hand switch

COMMENTS:

___ SAT

___ UNSAT STEP 5: [Step 4] PERFORM the following: [a] CLOSE 1-FCV-65-10, EGTS TR-A U1 SUCT DMPR.

[b] CLOSE 1-FCO-65-26, EGTS TO U1 SHIELD BLDG.

STANDARD: Applicant closes 1-FCV-65-10 with 1-HS-65-10; applicant closes 1-FC0-65-26 with 1-HS-65-26. Respective hand switches red lights are off and green lights are LIT.

Step is critical to shutdown return ventilation lineup to normal following 10 hour1.157407e-4 days <br />0.00278 hours <br />1.653439e-5 weeks <br />3.805e-6 months <br /> run.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT REV. 0 PAGE 86 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 6: [STEP 5] IF Train A EGTS to be returned to STANDBY, THEN: PERFORM the following:

CRITICAL STEP NOMENCLATURE LOCATION POSITION UNID EGTS TR-A U1 SUCT DMPR 0-M-27B A AUTO 1-HS-65-10 EGTS TR-A U1 SHIELD BLDG 0-M-27B A AUTO 1-HS-65-26 STANDARD: Applicant places 1-HS-65-10 and 1-HS-65-26 to the A AUTO position.

Step is critical to return these hand switches to ES Standby alignment.

COMMENTS:

___ SAT

___ UNSAT

STEP 7: [Step 6] IF Train B EGTS is to be shutdown, THEN GO TO Section 7.2.

STANDARD: Applicant determines that this step does not apply and proceeds to the next step.

COMMENTS:

___ SAT

___ UNSAT STEP 8: [Step 7]

IF EGTS is to be returned to STANDBY, THEN GO TO Section 5.0 to align EGTS for STANDBY.

STANDARD: Applicant goes to Section 5.0.

COMMENTS:

___ SAT

___ UNSAT REV. 0 PAGE 87 OF 131 WATTS BAR NUCLEAR PLANT B.1.h NOTE TO EVALUATOR: The following performance steps are from section 5.1 of SOI-65.02.

CAUTION IF EGTS is being returned to standby after auto actuation, THEN both Sections 7.1 and 7.2 must be performed prior to Standby Readiness alignment.

STEP 9: [Step 1] ENSURE a ØA Cntmt Isolation signal is NOT present.

STANDARD: Applicant determines that ØA Cntmt Isolation signal is NOT present by checking Master Isol Signal PNLs 1-XX-55-6C & 6D

ØA light DARK.

NOTE TO EVALUATOR: This was previously performed in step 2 of JPM.

COMMENTS:

___ SAT

___ UNSAT STEP 10: [Step 2] ENSURE the following valves are CLOSED and PLACE 1-HS-65-81/86 in A AUTO. CRITICAL STEP NOMENCLATURE LOCATION POSITION UNID U1 EGTS-ANN P CNTLR A ISOL 0-M-27B A AUTO 1-HS-65-81/86 STANDARD: Applicant locates 1-HS-65-81/86 and places in A-AUTO. Step is critical to establishing EGTS configuration for automatic start after a ØA Cntmt Isolation signal.

COMMENTS:

___ SAT

___ UNSAT

REV. 0 PAGE 88 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 11: [STEP 3] ENSURE breaker position for the following:

NOMENCLATURE LOCATION POSITION UNID 120VAC VITAL INST POWER BD 1-I EGTS TRAIN A AUX RELAYS 1-PCV-65-81/1-PCV-65-86 Bkr 38 OFF 1-BKR-235-1/38 STANDARD: Applicant contacts the Control Building AUO (or an AUO) and requests performance of Step 3.

    • CUE: When asked as the AU O, state "1-BKR-235-1/38 is in the OFF position".

COMMENTS:

___ SAT

___ UNSAT

STEP 12: [Step 4] ENSURE the following valves are CLOSED and PLACE 1-HS-65-83/87 in A AUTO. NOMENCLATURE LOCATION POSITION UNID U1 EGTS-ANN P CNTLR B ISOL 0-M-27B A AUTO 1-HS-65-83/87 STANDARD: Applicant locates 1-HS-65-83/87 and places in A-AUTO. Step is critical to establishing EGTS configuration for automatic start after a ØA Cntmt Isolation signal.

COMMENTS:

___ SAT

___ UNSAT

REV. 0 PAGE 89 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 13: [STEP 5] ENSURE breaker position for the following:

NOMENCLATURE LOCATION POSITION UNID 120VAC VITAL INST POWER BD 1-II EGTS TRAIN B AUX RELAYS 1-PCV-65-81/1-PCV-65-86 Bkr 38 OFF 1-BKR-235-2/38 STANDARD: Applicant contacts an AUO and requests performance of Step

5. **CUE: When asked as the AUO, stat e"1-BKR-235-2/38 is in the OFF position".

COMMENTS:

___ SAT

___ UNSAT

STEP 14: [STEP 6] PERFORM the following:

NOMENCLATURE LOCATION POSITION UNID EGTS FAN A & DISCHG DMPR 0-M-27B A AUTO 0-HS-65-23A EGTS FAN B & DISCHG DMPR 0-M-27B A AUTO 0-HS-65-42A STANDARD: Applicant locates 0-HS-65-23A and ensures in A-AUTO. Applicant locates 0-HS-65-42A and ensures in A-AUTO.

COMMENTS:

___ SAT

___ UNSAT

REV. 0 PAGE 90 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 15: [STEP 7] OPEN the following valves, and PLACE the handswitches in A AUTO:

CRITICAL STEP NOMENCLATURE LOCATION POSITION UNID U1 ANN VAC FANS SUCT 0-M-27B OPEN, HS in A AUTO 0-HS-65-52 U1 ANN VAC FANS SUCT 0-M-27B OPEN, HS in A AUTO 0-HS-65-53 STANDARD: Applicant locates 0-HS-65-52 and ensures OPEN and in A-AUTO. Applicant locates 0-HS-65-53 and ensures OPEN and in A-AUTO. Step is critical to est ablishing EGTS configuration for automatic start after a ØA Cntmt Isolation signal.

COMMENTS:

___ SAT

___ UNSAT

NOTES 1) The following step may be N/A'd if annulus vacuum fans are running. 2) If a phase A signal has been present, the next step may start one Ann Vac Fan due to low flow. Either fan may be selected first. Flow should be allowed to stabilize before the second fan is placed in auto to avoid two fans running. SOI-65.01 Section 5.0 should be referenced to ensure proper damper alignment and control after fan start.

REV. 0 PAGE 91 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 16: [STEP 8] PLACE the following handswitches in STOP to break seal-in, AND RETURN to A-P AUTO:

NOMENCLATURE LOCATION POSITION UNID ANN VAC FAN 1A & SUCT FCO 0-M-27B A P AUTO 1-HS-65-77A ANN VAC FAN 1B & SUCT FCO 0-M-27B A P AUTO 1-HS-65-74A STANDARD: Applicant verifies that annulus vacuum fans are running and N/As the step.

COMMENTS:

___ SAT

___ UNSAT

STEP 17: [STEP 9] IF an accident signal (A) has occurred and WHEN Annulus P is greater than 4.0 in. H2O, THEN: (N/A if TACF 1-07-0002-065 is in effect.) PERFORM the following

NOMENCLATURE LOCATION POSITION UNID PCV-65-81 and PCV-65-86, EGTS CNTMT ANNULUS DP

RESET A5W/737, 1-JB -292-4013-A, N. of GFFD Rm. RESET 1-HS-65-80 and 1-HS-65-90 PCV-65-83 and PCV-65-87, EGTS CNTMT ANNULUS DP RESET A4V/737, 1-JB-292-4015-B, S. of GFFD Rm. RESET 1-HS-65-82 and 1-HS-65-97 STANDARD: Applicant determines that no accident signal was present and N/As the step COMMENTS:

___ SAT

___ UNSAT

CAUTION PDIC-65-80 & 82 Setpoint Thumbwheels are adjusted by MIG only.

REV. 0 PAGE 92 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 18: [STEP 10] ENSURE the following controllers in AUTO: NOMENCLATURE LOCATION POSITION UNID EGTS-ANN P CONTROL 0-M-27B AUTO 1-PDIC-65-82 EGTS-ANN P CONTROL 0-M-27B AUTO 1-PDIC 80 STANDARD: Applicant locates 1-PDIC-65-82 and ensures controller is in AUTO Applicant locates 1-PDIC 80 and ensures controller is in AUTO COMMENTS:

___ SAT

___ UNSAT

REV. 0 PAGE 93 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 19: [STEP 11] ENSURE the following:

NOMENCLATURE LOCATION POSITION UNID EGTS TR A DECAY COOLING 0-M-27B CLOSE 0-HS-65-28B EGTS TR A DECAY COOLING 0-M-27B CLOSE 0-HS-65-28A EGTS TR B DECAY COOLING 0-M-27B CLOSE 0-HS-65-47A EGTS TR B DECAY COOLING 0-M-27B CLOSE 0-HS-65-47B STANDARD:

Applicant locates 0-HS-65-28B and ensures that it is CLOSED.

Applicant locates 0-HS-65-28A and ensures that it is CLOSED.

Applicant locates 0-HS-65-47A and ensures that it is CLOSED.

Applicant locates 0-HS-65-47B and ensures that it is CLOSED.

COMMENTS:

___ SAT

___ UNSAT

REV. 0 PAGE 94 OF 131 WATTS BAR NUCLEAR PLANT B.1.h STEP 20: [STEP 12] PERFORM the following:

NOMENCLATURE LOCATION POSITION UNID EGTS TR-A U1 SUCT DMPR 0-M-27B A AUTO 1-HS-65-10 EGTS TR-A U1 SUCT DMPR 0-M-27B CLOSE 1-HS-65-8 EGTS FAN B U1 SUCT DMPR 0-M-27B CLOSE 1-HS-65-51 EGTS TR-B U1 SUCT DMPR 0-M-27B A AUTO 1-HS-65-30 EGTS TO U1 SHIELD BLDG 0-M-27B A AUTO 1-HS-65-26 EGTS TO U1 SHIELD BLDG 0-M-27B A AUTO 1-HS-65-27 STANDARD:

Applicant locates 1-HS-65-10 and ensures that it is in A-AUTO.

Applicant locates 1-HS-65-8 and ensures that it is CLOSED.

Applicant locates 1-HS-65-51 and ensures that it is CLOSED.

Applicant locates 1-HS-65-30 and ensures that it is in A-AUTO.

Applicant locates 1-HS-65-26 and ensures that it is in A-AUTO.

Applicant locates 1-HS-65-27 and ensures that it is in A-AUTO.

COMMENTS:

___ SAT

___ UNSAT

STEP 21: Notify the Unit Supervisor that "A" Train EGTS Fan is shutdown and realigned for standby readiness.

STANDARD: Applicant notifies the Unit Supervisor that "A" Train EGTS Fan is shutdown and realigned for standby readiness.

COMMENTS:

END OF TASK

___ SAT

___ UNSAT

TIME STOP: ________

REV. 0 PAGE 95 0F 131 WATTS BAR NUCLEAR PLANT B.1.i APPLICANT CUE SHEET (TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)

DIRECTION TO TRAINEE:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit 1 is at 100% power.
2. 0-SI-65-6-A "Emergency Gas Treatment System Train A 10-Hour Operation" performance in progress.
3. "A" Train EGTS Fan has been in service for 10 hours1.157407e-4 days <br />0.00278 hours <br />1.653439e-5 weeks <br />3.805e-6 months <br />.
4. You are a support operator in the control room.

INITIATING CUES:

1. The Unit Supervisor directs you to shutdown the "A" Train EGTS Fan per SOI-65.02 and return EGTS to Standby Alignment per the procedure.
2. You are to notify Unit Supervisor when you have completed the task.

REV. 0 PAGE 96 0F 131 WATTS BAR NUCLEAR PLANT B.1.i

ALTERNATE PATH

B.1.i Perform a boration of the RCS (LOCALLY) per AOI-34, "IMMEDIATE BORATION."

REV. 0 PAGE 97 0F 131 WATTS BAR NUCLEAR PLANT B.1.i

REV. 0 PAGE 98 0F 131 WATTS BAR NUCLEAR PLANT B.1.i Task: Perform a Boration of the RCS (LOCALLY) per AOI-34 "IMMEDIATE BORATION."

Alternate Path:

1-FCV-62-138 will not pass more than 8 gpm, requiring manual valve 1-ISV-62-929 to be opened locally. This also requires use of control room flow indication, since the indication of flow via this path is not available locally.

Facility JPM #: 3-OT-JPMA020B Rev 4.

K/A Rating(s):

024AA1.04 [3.6/3.7] 024AK3.01 [4.1/4.4] 024AA1.18 [3.7/3.6] 024AA1.20 [3.2/3.3]

Task Standard: Total boration flow rate of 45 gpm has been established on 1-FCV-62-137A and 1-FI-62-139 after partially opening 1-FCV-62-136 and fully opening 1-ISV-62-929 locally. Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __ __ In-Plant __ X__ Perform ______ Simulate __X__

References

AOI-34, "IMMEDIATE BORATION," Rev. 23.

Task Number: AUO-062-AOI-27-001 APPLICABLE FOR: AUO/RO/SRO 10CFR55.45: 6, 8, 9, 10 Validation Time: 17 min.

Time Critical:

No ===========================================================================

Candidate: ___________________________ _________________ Time Start: ________

NAME SSN/EINTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 0 PAGE 99 0F 131 WATTS BAR NUCLEAR PLANT B.1.i REV. 0 PAGE 100 0F 131 WATTS BAR NUCLEAR PLANT B.1.i Tools/Equipment/Procedures Needed:

Hard Hat, Gloves, Safety Glasses, Hearing Protection, and Plant Approved Shoes.

Procedure AOI-34, "Immediate Boration".

ALARA considerations NOTE: Start this JPM at the RAD WASTE DESK.

REV. 0 PAGE 101 0F 131 WATTS BAR NUCLEAR PLANT B.1.i READ TO OPERATOR

DIRECTION TO TRAINEE:

I will explain the initial conditions, and state the task to be performed. All steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you.

Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you. INITIAL CONDITIONS:

1. The Reactor has been tripped and AOI-34, "IMMEDIATE BORATION,"

is being performed due to an RCS cooldown resulting in temperature less than 547

°F. 2. The normal makeup controls did not function correctly to establish boric acid flow. 3. Both Boric Acid pumps are operating in FAST speed.

4. 1-FCV-62-138 did not open from the Main Control Room.

INITIATING CUES:

1. You have been assigned to perform AOI-34, "IMMEDIATE BORATION,"

Step 6 actions to locally establish boric acid flow.

2. You are to establish a minimum boric acid flow rate of 45 gpm.

REV. 3 PAGE 102 0F 13 WATTS BAR NUCLEAR PLANT B.1.i START TIME: _______

STEP 1: Obtain a copy of the appropriate instruction.

STANDARD: EXAMINER'S CUE: After the method of obtaining an instruction properly has been demonstrated, the evaluator provides a copy of the instruction.

COMMENTS:

___ SAT

___ UNSAT STEP 2: [STEP 6.b. RNO] Locally ADJUST 1-FCV-62-138 to obtain required flow.

STANDARD: 1-FCV-138-B, EMERGENCY BORATION FLOW CONTROL, is located. The manual lever is pushed to the manual position (in direction of arrow) and the Applicant opens the valve by turning the hand wheel in the counter-clockwise direction.

CUE: State "the motor operator hand wheel rotates a few turns (3-4) and stops."

COMMENTS:

___ SAT

___ UNSAT REV. 3 PAGE 103 0F 13 WATTS BAR NUCLEAR PLANT B.1.i STEP 3: [STEP 6.c.]

CHECK emergency borate flow on 1-FI-62-137A.

STANDARD: 1-FI-62-137A.has been checked and determination made that 8 gpm has been established, which is insufficient to meet the required flow rate. Entry into c. RNO is required, since the stated flow rate of 45 gpm is not established. Step is critical to evaluating whether a flow path has been established.

CUE: When applicant contacts the Main Control Room to check flow on 1- FI-62-137A, state "the indicator reads 8 gpm."

If the applicant checks local flow indicator 1-FI-62-137B, indicate 8 gpm on the meter.

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT

Note: The following step is required since valve could not be operated electrically STEP 4: [STEP 6c. RNO] Locally OPEN manual boration valve 1-ISV-62-929 [Blender Station/713].

STANDARD: 1-ISV-62-929 is opened by turning the hand wheel in the counter-clockwise direction. Step is critical because it initiates boration flow.

CUE: State "the hand wheel was rotated many turns in the counter-clockwise direction and has stopped."

COMMENTS:

CRITICAL STEP

___ SAT

___ UNSAT REV. 3 PAGE 104 0F 13 WATTS BAR NUCLEAR PLANT B.1.i STEP 5: [STEP 6.c. RNO continued]

ENSURE BA flow control 1-FCV-62-140 OPEN.

STANDARD: Applicant observes 1-FCV-62-140 and determines that the valve is OPEN

COMMENTS:

___ SAT

___ UNSAT STEP 6: [STEP c. RNO continued] ENSURE BA to Blender, 1-FI-62-139, indicating flow.

STANDARD: Applicant contacts the MCR to determine if flow is indicated on 1-FI-62-139. The applicant determines that the combined flow rate from 1-FI-62-137A and 1-FI-62-139 of 48 gpm is greater than the required flow rate of 45 gpm.

CUE: When MCR is contacted, state"1-FI-62-139 is indicating 40 gpm."

COMMENTS:

___ SAT

___ UNSAT REV. 3 PAGE 105 0F 13 WATTS BAR NUCLEAR PLANT B.1.i STEP 15: [7] IF emergency boration flow established , THEN GO TO Step 9.

STANDARD: Applicant contacts MCR and reports that emergency boration flow has been established.

CUE: Acknowledge report as MCR operator using repeat back.

COMMENTS:

END OF TASK

___ SAT

___ UNSAT TIME STOP: ________

REV. 0 PAGE 106 0F 15 WATTS BAR NUCLEAR PLANT B.1.j DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you.

Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you. INITIAL CONDITIONS:

1. The Reactor has been tripped and AOI-34 is being performed due to an RCS cooldown resulting in temperature less than 547

°F. 2. The normal makeup controls did not function correctly to establish boric acid flow. 3. Both Boric Acid pumps are operating in FAST speed.

4. 1-FCV-62-138 did not open from the Main Control Room. INITIATING CUES:
1. You have been assigned perform AOI-34, Step 6.b RNO actions to locally establish boric acid flow.
3. You are to establish a minimum boric acid flow rate of 45 gpm.

REV. 0 PAGE 107 0F 15 WATTS BAR NUCLEAR PLANT B.1.j

B.1.j Perform E-3, Attachment 3, Steamline Isolation (Local)

REV. 0 PAGE 108 0F 15 WATTS BAR NUCLEAR PLANT B.1.j Task: Perform E-3, "Steam Generator Tube Rupture," Attachment 3, "Steamline Isolation (Local)."

Alternate Path:

N/A Facility JPM #: 3-OT-JPMA054 Rev 3 K/A Rating(s):

038 EA1.32 [4.6/4.7] 2.1.30 [3.9/3.4]

Task Standard: All nine steam line traps have been located. One steam trap has been isolated (all others are isolated the same way). Main steam supplies to each MFP turbine have been located and isolated.

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator __ __ In-Plant __ X__ Perform ______ Simulate __X__

References

E-3, Steam Generator Tube Rupture, Rev. 22 Task Number: RO-113-EOP-3-001 APPLICABLE FOR: AUO/RO/SRO 10CFR55.45: 5.6 Validation Time: 20 min.

Time Critical: No ===========================================================================

Candidate: ___________________________ _________________ Time Start: ________

NAME SSN/EINTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 0 PAGE 109 0F 15 WATTS BAR NUCLEAR PLANT B.1.j Tools/Equipment/Procedures Needed:

Hard Hat, Safety Glasses, Flashlight, Hearing Protection, Gloves, and Plant Approved Shoes.

E-3, Attachment 3.

SAFETY Considerations:

High Temperature Pipes, Ladder Safety, ALARA considerations.

NOTE: Start this JPM in the MCR.

EVALUATOR NOTE: Provide copy of E-3, "Steam Generator Tube Rupture," Attachment 3, "Steamline Isolation (Local)." to applicant with applicant's cue sheet.

REV. 0 PAGE 110 0F 15 WATTS BAR NUCLEAR PLANT B.1.j READ TO APPLICANT

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit 1 is in Mode 3 after a Steam Generator tube rupture on S/G # 2.
2. The Main Steam Isolation Valve (MSIV) on S/G # 2 has failed to close.
3. Main Steam line warming is NOT in progress.

INITIATING CUES:

1. The MCR operator has directed you to locally isolate the steam traps and main feed pump turbine on the main steam system by performing E-3, "Steam Generator Tube Rupture," Attachment 3, "Steamline Isolation (Local)."
2. You are to notify the MCR operator when E-3, Attachment 3 has been completed.

REV. 0 PAGE 111 0F 15 WATTS BAR NUCLEAR PLANT B.1.j START TIME: _______

STEP 1: Obtain a copy of the procedure.

___SAT

___UNSAT STANDARD: A copy of E-3, Attachment 3, Steamline Isolation (Local) is obtained.

EXAMINER'S CUE: Provide E-3, Attachment 3,"Steamline Isolation (Local)" to the applicant.

COMMENTS:

STEP 2: [Step 1] COORDINATE steam trap isolation with RADPROT.

___SAT

___UNSAT STANDARD: The applicant contacts RADCON.

CUE: State "The survey of steam lines has been made and is continuing periodically."

COMMENTS:

EXAMINER NOTE: Applicant must locate all nine steam traps and demonstrate how to isolate one of them.

The applicant may use a flashlight to point out the hard to reach traps.

The applicant must locate an "EOP ladder" for use in operating valves located in hard to reach locations.

REV. 0 PAGE 112 0F 15 WATTS BAR NUCLEAR PLANT B.1.j STEP 3: [STEP 2] CLOSE at least one valve listed for each steam moisture trap manifold: [MAIN STEAM LINES]

CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 200 1-ISV-1-916 OR1-ISV-1-922 [T1M/708]

STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-200 can be accomplished by either closing 1-ISV-1-916 or closing 1-ISV-1-922. (Rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

___SAT

___UNSAT COMMENTS:

REV. 0 PAGE 113 0F 15 WATTS BAR NUCLEAR PLANT B.1.j STEP 4: [STEP 2 continued]

CLOSE at least one valve listed for each steam moisture trap manifold: [MAIN STEAM LINES] CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 201 1-ISV-1-926 OR1-ISV-1-932 [T1M/708]

___SAT

___UNSAT STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-201 can be accomplished by either closing 1-ISV-1-926 or closing 1-ISV-1-932. (Rotating hand wheel clockwise) Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

COMMENTS:

STEP 5: [STEP 2 continued]

CLOSE at least one valve listed for each steam moisture trap manifold: [MAIN STEAM LINES]

CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 202 1-ISV-1-936 OR1-ISV-1-942 [T1M/708]

___SAT

___UNSAT STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-202 can be accomplished by either closing 1-ISV-1-936 or closing 1-ISV-1-942. (Rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

COMMENTS:

REV. 0 PAGE 114 0F 15 WATTS BAR NUCLEAR PLANT B.1.j STEP 6: [STEP 2 continued]

CLOSE at least one valve listed for each steam moisture trap manifold: [MAIN STEAM LINES] CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 203 1-ISV-1-946 OR1-ISV-1-952 [T1M/708]

STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-203 can be accomplished by either closing 1-ISV-1-946 or closing 1-ISV-1-952. (Rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

___SAT

___UNSAT COMMENTS:

STEP 7: [STEP 2 continued]

CLOSE at least one valve listed for each steam moisture trap manifold: [COMMON STEAM HEADER]

CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 204 1-ISV-1-956 OR1-ISV-1-962 [T4J/708]

___SAT

___UNSAT STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-204 can be accomplished by either closing 1-ISV-1-956 or closing 1-ISV-1-962. (Rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

COMMENTS:

REV. 0 PAGE 115 0F 15 WATTS BAR NUCLEAR PLANT B.1.j STEP 8: [STEP 2 continued]

CLOSE at least one valve listed for each steam moisture trap manifold: [COMMON STEAM HEADER]

CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 206 1-ISV-1-966 OR1-ISV-1-972 [T6J/708]

STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-206 can be accomplished by either closing 1-ISV-1-966 or closing 1-ISV-1-972. (Rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

___SAT

___UNSAT COMMENTS:

STEP 9: [STEP 2 continued]

CLOSE at least one valve listed for each steam moisture trap manifold: [STEAM DUMP HEADER]

CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 207 1-ISV-1-976 OR1-ISV-1-982 [T7H/708]

STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-207 can be accomplished by either closing 1-ISV-1-976 or closing 1-ISV-1-982. (Rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

___SAT

___UNSAT COMMENTS:

REV. 0 PAGE 116 0F 15 WATTS BAR NUCLEAR PLANT B.1.j STEP 10: [STEP 2 continued]

CLOSE at least one valve listed for each steam moisture trap manifold: [STEAM DUMP HEADER] CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 208 1-ISV-1-986 OR1-ISV-1-992 [T7G/708]

STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-208 can be accomplished by either closing 1-ISV-1-986 or closing 1-ISV-1-992. (Rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

___SAT

___UNSAT COMMENTS:

REV. 0 PAGE 117 0F 15 WATTS BAR NUCLEAR PLANT B.1.j STEP 11: [STEP 2 continued]

CLOSE at least one valve listed for each steam moisture trap manifold: [STEAM DUMP HEADER]

CRITICAL STEP MSTR TRAP LEVEL SWITCH MSTR TRAP STR ISOL MSTR TRAP DRAIN ISOL LOCATION 209 1-ISV-1-996 OR1-ISV-1-1002 [T7F/708]

STANDARD: The applicant locates each moisture trap. Demonstration of the isolation of the trap associated with 1-LS-209 can be accomplished by either closing 1-ISV-1-996 or closing 1-ISV-1-1002. (Rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

___SAT

___UNSAT COMMENTS:

STEP 12: [STEP 3] CLOSE steam supply isolation and bypass for each Main Feed Pump Turbine:

CRITICAL STEP MFPT NOMENCLATURE LOCATION POSITION UNID 1A MFPT 1A HP STEAM SUPPLY ISOL T2J/729 CLOSED 1-ISV-1-611 STANDARD: The applicant locates valve and closes valve (rotating hand wheel clockwise). Step is critical to isolate flow path.

CUE: State "the hand wheel turns a few rotations a nd gets snug."

___SAT

___UNSAT COMMENTS:

REV. 0 PAGE 118 0F 15 WATTS BAR NUCLEAR PLANT B.1.j STEP 13: [STEP 3 continued]

CLOSE steam supply isolation and bypass for each Main Feed Pump Turbine:

MFPT NOMENCLATURE LOCATION POSITION UNID 1A MFPT 1A HP STEAM SUPPLY ISOL BYPASS T2J/729 CLOSED 1-IBV-1-613 STANDARD: The applicant locates valve and checks valve closed (rotating hand wheel clockwise).

CUE: State "the hand wheel turns a few rotations a nd gets snug."

___SAT

___UNSAT COMMENTS:

STEP 14: [STEP 3 continued]

CLOSE steam supply isolation and bypass for each Main Feed Pump Turbine:

CRITICAL STEP MFPT NOMENCLATURE LOCATION POSITION UNID 1B MFPT 1B HP STEAM SUPPLY ISOL T2H/729 CLOSED 1-ISV-1-612 STANDARD: The applicant locates valve and closes valve (rotating hand wheel clockwise). Step is critical to isolate flow path.

___SAT

___UNSAT CUE: State "the hand wheel turns a few rotations a nd gets snug."

COMMENTS:

REV. 0 PAGE 119 0F 15 WATTS BAR NUCLEAR PLANT B.1.j STEP 16: [STEP 3] CLOSE steam supply isolation and bypass for each MFPT:

MFPT NOMENCLATURE LOCATION POSITION UNID 1B MFPT 1B HP STEAM SUPPLY ISOL BYPASS T2H/729 CLOSED 1-IBV-1-614 STANDARD: The applicant locates valve and checks valve closed (rotating hand wheel clockwise).

CUE: State "the hand wheel does not move with clockwise force on hand wheel".

___SAT

___UNSAT

COMMENTS:

STEP 17: Notify the MCR Operator that local main steam isolation has been completed per E-3, Attachment 3.

___SAT

___UNSAT STANDARD: The MCR Operator has been notified that local main steam isolation has been performed per E-3, Attachment 3.

CUE: When notified, acknowledge the report.

COMMENTS:

END OF TASK TIME STOP: ________

REV. 4 PAGE 120 0F 131 WATTS BAR NUCLEAR PLANT B.1.k CANDIDATE CUE SHEET (TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)

DIRECTION TO TRAINEE:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. Unit 1 is in Mode 3 after a Steam Generator tube rupture on S/G # 2.
2. The Main Steam Isolation Valve (MSIV) on S/G # 2 has failed to close.
3. Main Steam line warming is NOT in progress.

INITIATING CUES:

1. The MCR operator has directed you to locally isolate the steam traps and main feed pump turbine on the main steam system by performing E-3, "Steam Generator Tube Rupture," Attachment 3, "Steamline Isolation (Local)."
2. You are to notify the MCR operator when E-3, Attachment 3 has been completed.

REV. 4 PAGE 121 0F 131 WATTS BAR NUCLEAR PLANT B.1.k

B.1.k Place the CVCS Cation Demineralizer in Service per SOI-62.04, "CVCS PURIFICATION SYSTEM."

REV. 4 PAGE 122 0F 131 WATTS BAR NUCLEAR PLANT B.1.k Task: Place the CVCS Cation Demineralizer in Service per SOI-62.04, "CVCS PURIFICATION SYSTEM," Alternate Path:

N/A Facility JPM #: 3-OT-JPMA041 K/A Rating(s):

004A1.07 [2.7/3.1] Task Standard: The appropriate valves have been located and opened to place the CVCS cation bed in service per SOI-62.04, "CVCS PURIFICATION SYSTEM."

Preferred Evaluation Location: Preferred Evaluation Method:

Simulator ____ In-Plant __X___ Perform __X___ Simulate ___ _

References

SOI-62.04, "CVCS PURIFICATION SYSTEM," Rev. 53 Task Number: AUO-062-AOI-028-001 APPLICABLE FOR: RO/SRO 10CFR55.45: 8, 9 Validation Time: 20 min.

Time Critical:

No ===========================================================================

Applicant: ___________________________ _________________ Time Start: ________

NAME SSNTime Finish: ________

Performance Rating: SAT ____ UNSAT ____

Performance Time ___

Examiner: _____________________________

_____________________________/________ NAME SIGNATURE DATE

===============================================================

COMMENTS REV. 4 PAGE 123 0F 131 WATTS BAR NUCLEAR PLANT B.1.k Tools/Equipment/Procedures Needed:

Hard Hat, Safety Glasses, Hearing Protection, Gloves and Plant Approved Shoes Copy of SOI-62.04, "CVCS PURIFICATION SYSTEM," Rev. 53, Section 8.2 and Attachment 1 with data entered.

SAFETY CONSIDERATIONS

Hot pipes, high noise, and heat.

Radiation levels.

Ladder use to reach valve handwheels.

REV. 4 PAGE 124 0F 131 WATTS BAR NUCLEAR PLANT B.1.k READ TO APPLICANT

DIRECTION TO APPLICANT:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. The Unit is at 100% power.
2. Letdown orifice valve 1-FCV-62-74 is open and letdown flow (as indicated in MCR) is 75 gpm.
3. RCS boron concentration is 776 ppm.
4. Chemistry has requested that cation bed be placed in service for 53 minutes.
5. The Cation bed has been filled and vented.
6. SOI-62.04, "CVCS PURIFICATION SYSTEM," Attachment 1, Resin Status Sheet indicates that the Cation Bed is at the same boron concentration of the RCS.

INITIATING CUES:

1. The MCR operator has directed you to place the CVCS Cation Bed in service per procedure.
2. You are to notify the MCR when the CVCS Cation Bed is in service.

REV. 0 PAGE 125 0F 131 WATTS BAR NUCLEAR PLANT B.1.k START TIME: _______

STEP 1: Obtain a copy of the procedure.

STANDARD: Applicant has obtained a copy of SOI-62.04, "CVCS PURIFICATION SYSTEM," Section 8.2 EXAMINER'S CUE:

After the applicant has de monstrated the method of obtaining the correct instruction, the evaluator can

provide a copy of the instruction.

COMMENTS:

___ SAT

___ UNSAT STEP 2: [1] ENSURE CB FILLED and VENTED per Section 8.1.

STANDARD: Applicant determines the Cation Bed is filled and vented per the INITIAL CONDITIONS provided.

EXAMINER'S CUE: If asked, inform the applicant that Section 8.1 is complete.

COMMENTS:

___ SAT

___ UNSAT Due to the location of one of the valve handwheels that will be operated, the applicant may require a ladder to reach the valve handwheel. If required, a general use ladder, NOT an EOP ladder, must be located by the operator.

REV. 0 PAGE 126 0F 131 WATTS BAR NUCLEAR PLANT B.1.k STEP 3: [2] PERFORM the following:

NOMENCLATURE LOCATION POSITION UNID CVCS CATION DEMIN BED INLET A3T/713 CLOSED 1-ISV-62-915 CVCS CATION DEMIN BED OUTLET A3T/713 CLOSED 1-ISV-62-916 CVCS CATION DEMIN BED VENT A3T/713 CLOSED 1-VTV-62-917 CVCS CATION DEMIN BED RESIN FILL A5U/737 CLOSED 1-ISV-62-918 CVCS CATION DEMIN BED RESIN DISCH A7U/713 CLOSED 1-ISV-62-919 CVCS CATION DEMIN BED DRAIN A3T/713 CLOSED 1-DRV-62-920 CVCS CATION BED FLUSH A3T/713 CLOSED 1-FLV-62-921 STANDARD: The above listed valves have been located and checked closed (clockwise to close).

EVALUATOR CUE: State "The handwheel will not rotate".

COMMENTS:

___ SAT

___ UNSAT STEP 4: [3] ENSURE 1-ISV-62-922, CVCS MIXED BED DEMIN OUTLET [A3T/713], is OPEN.

STANDARD: 1-ISV-62-922 is verified to be open.

EVALUATOR CUE: State "the handwheel will not rotate".

COMMENTS:

___ SAT

___ UNSAT REV. 0 PAGE 127 0F 131 WATTS BAR NUCLEAR PLANT B.1.k STEP 5: [4] REVIEW Attachment 1, Resin Status Sheet to ensure CB is FILLED and BORATED.

STANDARD: Applicant determines that the CB is filled and borated (given in initial conditions) and proceeds to the next step.

EVALUATOR CUE: Hand the applicant the Attachment 1 Resin Status Sheet.

COMMENTS:

___ SAT

___ UNSAT STEP 6: [5] NOTIFY SRO of intent to place CB in service, and its current boron concentration as recorded on Attachment 1, Resin Status Sheet.

STANDARD: The applicant contacts SRO and notifies them of intent to place cation Bed in service, advises them of boron concentration recorded on Attachment 1.

COMMENTS:

___ SAT

___ UNSAT CAUTION Cation Bed may need to be flushed to minimize reactivity effects if cation bed boron concentration varies more than 20 ppm from that of the RCS boron concentration or if a new cation bed is being placed in service.

REV. 0 PAGE 128 0F 131 WATTS BAR NUCLEAR PLANT B.1.k STEP 7: [6] OPEN 1-ISV-62-915, CVCS CATION DEMIN BED INLET.

STANDARD: 1-ISV-62-915 has been located and opened (turned in the counter-clockwise direction).

EVALUATOR CUE: State "the hand wheel rotates several turns and stops."

If indicator checked, indicate it points to the open position.

Step is critical to establish fl ow through the cation demineralizer.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT STEP 8: [7] IF flush is desired for cation bed, THEN GO TO Section 8.7, Flushing Cation Bed to Adjust Boron Prior to Use.

STANDARD: Applicant determines that flush is not required (per EVALUATOR CUE) and N/As step.

EVALUATOR CUE: State that flush is not necessary, nor desired at this time.

COMMENTS:

___ SAT

___ UNSAT CAUTION Maximum Cation Bed flow is 75 gpm. May be read locally at 1-FI-62-113 (Panel 1-L-57 at A3T/713).

REV. 0 PAGE 129 0F 131 WATTS BAR NUCLEAR PLANT B.1.k STEP 9: [8] SLOWLY OPEN 1-ISV-62-916, CVCS CATION DEMIN BED OUTLET.

STANDARD: 1-ISV-62-916 has been located and opened slowly (turned in the counter-clockwise direction).

EVALUATOR CUE: State "the hand wheel rotates several turns and stops."

If indicator checked, indicate it points to the open position.

Step is critical to establish fl ow through the cation demineralizer.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT STEP 10: [9] SLOWLY THROTTLE CLOSE 1-ISV-62-922, CVCS MIXED BED DEMIN OUTLET, until desired cation bed flow rate achieved.

STANDARD: 1-ISV-62-922 has been located and closed slowly (turned in the clockwise direction).

EVALUATOR CUE: State "the hand wheel rotates several turns and stops." If indicator checked, indicate it points to the

closed position.

EVALUATOR CUE: When 1 FI-62-113 is checked by the local indicator OR the CRT Monitor located near the demineralizer control valves, state it indicates 75 gpm. IF the MCR is contacted, state the letdown flow is 75 gpm.

Step is critical to establish fl ow through the cation demineralizer.

COMMENTS:

CRITICAL STEP ___ SAT

___ UNSAT REV. 0 PAGE 130 0F 131 WATTS BAR NUCLEAR PLANT B.1.k STEP 11: [10] RECORD Time, Date, and Flowrate when CB was placed in service on Attachment 1, Resin Status Sheet.

CUE: Another operator will enter the information on Attachment 1, Resin Status Sheet.

STANDARD: The applicant addresses entry of the Date, Time and Flow rate that the Cation Bed was placed in service is recorded on

.

COMMENTS:

___ SAT

___ UNSAT STEP 12: [11] NOTIFY Chemistry of Time, Date, and Flowrate when CB was placed in service.

STANDARD: The applicant notifies Chemistry of Time, Date, and Flowrate when CB was placed in service

COMMENTS:

END OF TASK

___ SAT

___ UNSAT STOP TIME ________

APPLICANT CUE SHEET (RETURN TO EXAMINER UPON COMPLETION OF TASK)

DIRECTION TO TRAINEE:

I will explain the initial conditions, and state the task to be performed. All control room steps shall be performed for this JPM, including any required communications. I will provide initiating cues and reports on other actions when directed by you. Ensure you indicate to me when you understand your assigned task. To indicate that you have completed your assigned task return the handout sheet I provided you.

INITIAL CONDITIONS:

1. The Unit is at 100% power.
2. Letdown orifice valve 1-FCV-62-74 is open and letdown flow (as indicated in MCR) is 75 gpm.
3. RCS boron concentration is 776 ppm.
4. Chemistry has requested that cation bed be placed in service for 53 minutes.
5. The Cation bed has been filled and vented.
6. SOI-62.04, "CVCS PURIFICATION SYSTEM," Attachment 1, Resin Status Sheet indicates that the Cation Bed is at the same boron concentration of the RCS.

INITIATING CUES:

1. The MCR operator has directed you to place the CVCS Cation Bed in service per procedure.
2. You are to notify the MCR when the CVCS Cation Bed is in service.