ML12233A701

Entergy Pre-Filed Hearing Exhibit ENT000531 - ASME Code, Sec. XI, Art. IWA-2000 (2001)

ML12233A701
Person / Time
Site:	Indian Point
Issue date:	08/20/2012
From:	- No Known Affiliation
To:	Atomic Safety and Licensing Board Panel
SECY RAS
References
RAS 23330, 50-247-LR, 50-286-LR, ASLBP 07-858-03-LR-BD01
Download: ML12233A701 (12)

Text

ARTICLE IWA-2000 EXAMINATION AND INSPECTION IW A-2100 GENERAL A02 IWA-2110 DUTIES OF THE INSPECTOR (a) The Inspector shall review the inspection plan and, as necessary, the implementation schedule (IWA-2420) prior to the start of preservice inspection and each inspection interval.

The review shall cover any features that are affected by the requirements of this Division, as applicable, and shall include the following: ( 1) examination categories and items (2) test and examination requirements (3) examination methods (4) percentage of parts selected for examination (5) disposition of test results (6) test frequency (7) system pressure tests (8) sequence of successive examinations Shop and field preservice examinations are exempt from prior review. (b) The Inspector shall review any revisions to the inspection plan and, as necessary, the implementation schedule during the preservice inspection or the tion interval. (c) The Inspector shall submit a report to the Owner documenting review of the items identified in IWA-211O(a) and (b). (d) The Inspector shall verify that the required nations and system pressure tests have been performed and the results recorded.

the Owner's agent and qualified in accordance with IWA-2300. (h) The Inspector may require, at any time, cation of any procedure or operator if the Inspector has reason to believe that the requirements are not being met. (i) The Inspector shall certify the examination ords after verifying that the requirements have been met and that the records are correct. (j) The Inspector shall verify that repair /replacement activities are performed in accordance with the ments of the Owner's Repair/Replacement Program. (k) The Inspector shall review the ment Program and its implementation.

IW A-2120 QUALIFICATION OF AUTHORIZED INSPECTION AGENCIES, INSPECTORS, AND SUPERVISORS (a) The inspection required by this Division shall be performed: ( 1) where the plant is in the United States, by an Inspector employed by a State or Municipality of the United States or an Inspector regularly employed by an insurance company authorized to write boiler and pressure vessel insurance in the United States; where the plant is in Canada, by an Inspector a Canadian Province or, if authorized A02 A03 IWA*2120 GENERAL REQUIREMENTS IWA*2213 ( c) The Authorized Inspection Agency shall be credited by AS ME in accordance with the provisions set forth in ASME QAI-l. IWA-2130 ACCESS FOR INSPECTOR The Owner shall arrange for an Inspector to have access to all parts of the plant as necessary to make the required inspections.

The Owner shall keep the Inspector informed of the progress of the preparatory work necessary to permit inspections and shall notify the Inspector at a time reasonably in advance of when the components will be ready for inspection.

IWA-2200 EXAMINATION METHODS (a) The three types of examinations used during inservice inspection are defined as visual, surface, and volumetric.

The examination method to be used is specified in Tables IWB-, IWC-, IWD-, IWE-, IWF-, and IWL-2S00-1.

If a component must be examined in a high radiation area, remotely controlled equipment may be advisable. (b) When preparation of a surface for nondestructive examination is required, the preparation shall be by a mechanical method. Such surfaces shall be blended into the surrounding area as may be required to perform the examination.

The wall thickness shall not be reduced below the minimum thickness required by design. mandatory Appendix D may be used for such surface preparation.

IWA-2210 VISUAL EXAMINATIONS Visual examinations shall be conducted in accordance with Section V, Article 9, T-941 for Written Procedures, and T-990 for Report of Examination Results. (d) Illumination for examination shall meet the quirements specified in Table IWA-2211-1. (e) It is not necessary to measure the illumination level on each examination surface when the same portable nonbattery-powered light source (e.g., drop light) or similar installed lighting equipment is strated to provide the illumination specified at the maximum examination distance. (f) When a battery-powered light is used, the quacy of the illumination level shall be checked before and after each examination or series of examinations, not to exceed 4 hr between checks. (g) Remote visual examination may be substituted for direct examination.

The remote examination dure shall be demonstrated capable of resolving ters in accordance with Table IWA-221l-1. ally, the remote examination system shall be capable of distinguishing the colors applicable to the component examination being conducted.

IWA-2212 VT-2 Examination A03 (a) VT-2 examination is conducted to detect evidence of leakage from pressure retaining components, with or without leakage collection systems, as required during the system pressure test. (b) VT-2 examination shall be conducted in ance with IWA-SOOO.

IWA-2213 VT-3 Examination A03 (a) VT-3 examination is conducted to determine the general mechanical and structural condition of nents and their supports by verifying parameters such as clearances, settings, and physical displacements; to detect discontinuities and imperfections, such as loss of integrity at bolted or welded connections, loose or missing parts, debris, corrosion, wear, or erosion; and to detect conditions that could affect operability or functional adequacy of snubbers and constant load and A02 A03 IWA-2213 2001 SECTION XI, DIVISION 1 IWA-2224 TABLE IWA-221l-1 VISUAL EXAMINATIONS Minimum Maximum Height, in. (mm), Illumination, Maximum Direct for Procedure Visual fc Examination Distance, Demonstration Examination

[Note (1)] ft (mm) Characters

[Note (2)] VT-l 50 2 (600) 0.044 n.O) VT-3 50 N/A 0.105 0.0) NOTES: (1) Resolution ofthe specified characters can be used in lieu of illumination measurement to verify illumination adequacy.

(2) For procedure demonstration, a test chart or card containing text with some lowercase characters, without an ascender or descender (e.g., a, c, e, 0), that meet the specified height requirements is required.

Measurements of the test chart or card shall be made once before its initial use with an optical comparator (lax or greater) or other suitable instrument to verify that the height of the lowercase characters without an ascender or descender meets the specified requirements.

light) or similar installed lighting equipment is strated to provide the illumination specified in Table IW A -2211-1 at the maximum examination distance. (f) a battery-powered light is used, the quacy of the illumination level shall be checked before and after each examination or series of examinations, not to exceed 4 hr between checks. (g) Remote visual examination may be substituted for direct examination.

The remote examination dure shall be demonstrated capable of resolving ters in accordance with Table IWA-2211-1. ally, the remote visual examination system shall be capable of distinguishing the colors applicable to the component examinations being conducted.

IWA-221S Replication Surface replication methods may be used for VT-I and VT-3 examinations when the surface resolution is at least equivalent to that of direct visual observation. ( c) Any flaw recorded by ultrasonic examination shall be compared to the volumetric examination acceptance standards of Table IWB-3514-1 or Table IWB-3514-2 for surface planar flaw. IWA-2221 Magnetic Particle Examination (a) Magnetic particle examination shall be conducted in accordance with Section V, Article 7. ( b) Magnetic particle examination of coated materials shall be conducted in accordance with Section V, Article 7, Appendix I. IW A-2222 Liquid Penetrant Examination Liquid penetrant examination shall be conducted in accordance with Section V, Article 6. IWA-2223 Eddy Current Examination IWA*2230 GENERAL REQUIREMENTS IWA*2231 IWA*2230 VOLUMETRIC EXAMINATION A volumetric examination indicates the presence of discontinuities throughout the volume of material and may be conducted from either the inside or outside surface of a component.

IWA-2231 Radiographic Examination Radiographic techniques, employing penetrating ation such as X-rays, gamma rays, or thermalized neutrons, may be utilized with appropriate cording devices, such as photographic film or papers, electrostatic systems, direct-image orthicons, or image converters.

For radiographic examinations employing either X-ray equipment or radioactive isotopes and photographic films, the procedure shall be as specified in Article 2 of Section V.

IWA-2232 GENERAL REQUIREMENTS IWA-2311 IWA-2232 Ultrasonic Examination Ultrasonic examination shall be conducted in ance with Appendix I. IW A-2233 Eddy Current Examination Eddy current examination shall be conducted in accordance with Section V, Article 8, Appendix II. IWA-2234 Acoustic Emission Examination Acoustic emission may be used in lieu of the sive inspections of IWB-2420(b) or IWC-2420(b) to monitor growth of flaws detected by other NDE ods. The flaws shall be sized by ultrasonic examination in accordance with Appendix I, Supplement 12, prior to initiating use of acoustic emission.

Acoustic emission monitoring shall be initiated prior to resuming operation of the system. Acoustic emission shall be conducted in accordance with Section V, Article 13, with the following additional requirements. (a) The following flaw growth calculation and ance criteria shall be used. ( 1) Every two months during the current inspection period, calculate the flaw growth in accordance with Section V, Article 13, Appendix I. Using this growth rate, predict the flaw size at the end of the current inspection period. (2) If the calculated flaw size at the end of the current inspection period meets the acceptance criteria of IWB-3600 or IWC-3600, as applicable, continue the two-month monitoring process described in (1) above. (3) If the calculated flaw size at the end of the current inspection period does not meet the acceptance criteria of IWB-3600 or IWC-3600, as applicable, the following actions shall be performed.

Calculate the flaw size at the end of the next two-month time span. If this calculated flaw size to the original schedule of successive inspections of IWB-2410 or IWC-2410, as applicable.

IW A-2240 ALTERNA TIVE EXAMINATIONS A02 Alternative examination methods, a combination of methods, or newly developed techniques may be tuted for the methods specified in the Construction Code or this Division, provided the Inspector is satisfied that the results are demonstrated to be equivalent or superior to those of the specified method. IWA-2300 QUALIFICATIONS OF NONDESTRUCTIVE EXAMINATION PERSONNEL IW A-2310 GENERAL (a) Personnel performing nondestructive tions (NDE) shall be qualified and certified using a written practice prepared in accordance with ANSI! ASNT CP-189, Standard for Qualification and Certification of Nondestructive Testing Personnel, as amended by the requirements of this Division.

tions based on SNT-TC-IA, ANSI N4S.2.6, or earlier editions of ANSI! ASNT CP-189 are valid until fication is required.

Recertification shall be in ance with the edition of ANSI! ASNT CP-189 referenced in IW A-1600 as amended by the requirements of this Division.

Outside agencies, as defined in Appendix VII, may be used to qualify NDE personnel; however, the Employer shall be solely responsible for the certification of Levels I, II, and III personnel.

Nondestructive and visual examination personnel qualified and certified in accordance with the requirements of this Division are qualified and certified to perform examinations in cordance with the requirements of previous Editions and Addenda.

IWA-2312 2001 SECTION XI, DIVISION 1 IWA-2321 IW A-2312 NDE Methods Listed in ANSI! ASNT CP-189 (a) Qualifications shall be based on the methods, techniques, procedures, and equipment used for the NDE required by this Division. (b) Training, qualification, and certification of sonic examination personnel shall also comply with the requirements of Appendix VII. (c) Training, qualification, and certification of visual examination personnel shall comply with the ments of Appendix VI. (d) The visual examination training and experience hours specified in CP-189 shall be applied to the combined certification of an individual for VT-l, VT-2, and VT-3 visual examination.

Certification in only one of the VT techniques is a limited certification, and the requirements of IW A-2350 apply. IW A-2313 NDE Methods Not Listed in ANSI! ASNT CP-189 Personnel using NDE methods not addressed in ANSI/ASNT CP-189 shall be qualified as defined in ANSI! ASNT CP-189 or the ACCP and the Employer's written practice.

IWA-2314 Certification and Recertification (a) Personnel shall be qualified by examination and shall be certified in accordance with ANSII ASNT CP-189, except that the ASNT Level III certificate is not required.

Levels I, II, and III personnel shall be fied by qualification examinations every 5 years. (b) Personnel qualified in accordance with the ACCP shall be recertified by examination every 5 years. (c) An ACCP certificate with current endorsements obtained by examination satisfies the General and tice Examination requirements for Levels I and II NDE personnel.

IWA-2316 Alternative Qualifications of VT-2 Visual Examination Personnel (a) In lieu of the requirements of IWA-231O through IWA-2314, VT-2 visual examination personnel may be qualified by satisfying the following requirements: ( I) at least 40 hr plant walkdown experience, such as that gained by licensed and nonlicensed operators, local leak rate personnel, system engineers, quality control personnel, and nondestructive examination sonnel (2) at least 4 hr of training in the Section XI requirements and plant-specific procedures for VT-2 visual examination (3) the vision test requirements of IWA-2321 (b) These alternative qualification requirements shall be described in the Employer's written practice.

IWA-2317 Alternative Qualifications of VT-3 Visual Examination Personnel (a) In lieu of the requirements of IW A-231O through IWA-2314, VT-3 visual examination personnel may be qualified by satisfying the following requirements: ( I) at least 40 hours4.62963e-4 days <br />0.0111 hours <br />6.613757e-5 weeks <br />1.522e-5 months <br /> plant experience, such as that gained by plant personnel involved in installation, maintenance, or examination of pumps, valves, and supports, quality control personnel, and nondestructive examination personnel (2) at least 8 hr of training in the Section XI requirements and plant-specific procedures for VT-3 visual examination (3) the vision test requirements of IWA-2321 ( b) The alternative qualification requirements shall be described in the Employer's written practice.

IW A-2320 QUALIFICA TION EXAMINATIONS IWA-2321 Vision Tests be administered 01 IWA-2321 GENERAL REQUIREMENTS IWA-2323 TABLE IWA-2322-1 NEAR-DISTANCE ACUITY TEST DISTANCES AND CHARACTER HEIGHTS Test Distance, in. (mm) 12 (05) 13 (30) 14 (56) 15 (81) 16 (406) Maximum Lower Case Character Height, in. (mm) 0.022 (0.56) 0.024 (0.61) 0.025 (0.63) 0.027 (0.68) 0.029 (0.73) NOTE: The test distances (eye to chart) and corresponding character heights provide a visual angle of 6.25 minutes, which is equivalent to a Snellen fraction of 20/25. ( b) Personnel shall demonstrate the capability to tinguish the colors applicable to the NDE methods for which certified and to differentiate contrast between these colors. IW A-2322 Near-Distance Test Chart Qualification A measurement of one of the near-distance test chart characters shall be made once before initial use, with an optical comparator (lOX or greater) or other suitable instrument, to verify that the height of a representative lower case character, without an ascender or descender (e.g., a, c, e, 0), for the selected type size, meets the requirements of Table IWA-2322-1.

This measurement shall be documented and traceable to the test chart. IWA-2323 Level III Personnel The qualifications of Level III NDE personnel shall be evaluated using written examinations and a stration Examination.

The written examinations shall 17 (3) At least fifteen (IS) questions that are similar to published Level II questions for other NDT methods. (b) The Method Examination shall consist of at least 65 questions: ( 1) At least thirty (30) questions related to mentals and principles that are similar to published ASNT Level III questions for each method. (2) At least fifteen (15) questions related to tion and establishment of procedures and techniques that are similar to published ASNT Level III questions for each method. (3) At least twenty (20) questions related to bility for interpreting codes, standards, and specifications related to the method. (e) The Specific Examination shall contain at least 30 questions covering equipment, techniques, dures, and administration of the Employer's written practice.

The Specific Examination shall also cover the NDE requirements of this Division, including acceptance standards and referenced codes and standards. (d) The Practical Examination shall be in accordance with ANSI/ASNT CP-189 requirements. (e) An ASNT Level III certificate with current dorsements obtained by examination for the applicable method satisfies the Basic and Method Examination requirements. (j) When an outside agency administers the tion and only a pass or fail grade is issued, the Employer shall assign a grade of 80% for a pass grade. (g) Level III personnel shall be recertified using the written Method, Specific, and Practical Examinations and the Demonstration Examination.

Alternatively, Level III personnel may be recertified using only the written Method and Specific Examinations, provided the following conditions are met: ( 1) The Level III candidate was previously certified or recertified using all the written examinations and the Demonstration Examination.

The Level III candidate is not being recertified service as defined in the IWA-2323 2001 SECTION XI, DIVISION 1 IWA-2420 Practical, and Demonstration examination requirements for Level III NDE personneL IWA-2330 LEVEL I RESPONSIBILITIES Level I personnel shall use written procedures when performing specific setups, calibrations, and tions and when recording data, These activities shall be conducted under the guidance of Level II or Level III personnel.

Level I personnel shall not evaluate or accept the results of a nondestructive examination, IWA*2340 LEVEL III EDUCATION Level III candidates shall have high school or lent education, IWA-2350 LIMITED CERTIFICATION Limited certification in a method is permitted for nel who are restricted to performing examinations of ited scope, i.e., limited operations or limited techniques within the method. Topics that are not relevant to the ited certification may be deleted from the ANSI! ASNT CP-189, Appendix VI, or Appendix VII training outline and may be accompanied by a corresponding reduction in training hours, examination content, and number of nation questions.

Only questions related to the limited training are required.

In addition, the required experience may be reduced by a corresponding amount. The specific methods and techniques covered by limited certification and the training, examination, and experience ments for limited certification shall be defined in the ten practice and documented in the individual's tion records. IW A*2360 LEVEL I AND LEVEL II TRAINING AND EXPERIENCE A candidate may be qualified directly to Level II with no time as a Level [ the (a) Graduate of a 4-year accredited engineering or science college or university with a degree in neering or science, plus I year experience in NDE in an assignment comparable to that of a Level II in the examination method. (b) Completion with a passing grade of at least the equivalent of 2 full years of engineering or science study at a university, college, or technical school, plus 2 years experience in an assignment comparable to that of a Level II in the examination method. (c) Four years experience in an assignment ble to that of a Level II in the examination method. IWA*2380 NDE INSTRUCTOR A02 In lieu of the requirements of CP-189, a candidate being considered for qualification as an NDE Instructor shall satisfy the Level III Basic and Method Examination requirements of IWA-2323 and shall meet one of the following requirements: (a) maintain a current teacher or vocational tion certificate issued by a state, municipal, provincial, or federal authority; or (b) complete a minimum of 40 hr instruction in training and teaching techniques.

IW A*2400 INSPECTION PROGRAM IW A-2410 APPLICA TION OF CODE EDITION AND ADDENDA The Code Edition and Addenda for preservice tion and for initial and successive inservice inspection intervals shall be in accordance with lOCFR50, Section 50.55a. IWA-2420 INSPECTION PLANS AND SCHEDULES Inspection plans and schedules shall be prepared for the preservice inspection, the first inservice inspection and intervals.

IWA-2420 GENERAL REQUIREMENTS IWA-2430 ( 1) identification of the components selected for examination and test, including successive exams from prior periods; (2) the Code requirements by examination category and item number for each component and the tion or test to be performed and the extent of the examination or test; (3) identification of drawings showing items that require examination; (4) list of examination procedures; (5) description of alternative examinations and identification of components to be examined using alternative methods; (6) identification of calibration blocks used for ultrasonic examination of components.

IWA*2425 INSPECTION PLAN AND SCHEDULE SUPPORTING DOCUMENTS Supporting documents necessary for inspection plan and schedule implementation such as diagrams or system drawings showing boundaries and system classifications, procedures, specifications, and other documents required for implementation of the inservice examinations and tests shall be available at the plant site. IWA*2430 INSPECTION INTERVALS (a) The inservice examinations and system pressure tests required by IWB, IWC, IWD, IWE, and inservice examinations and tests of IWF shall be completed during each of the inspection intervals for the service lifetime of the plant. The inspections shall be performed in accordance with the schedule of Inspection Program A of IWA-2431, or optionally, Inspection Program B of rw A-2432. It is not required that the inspection intervals of IWB, IWC, IWD, IWE, and IWF conform to the same inspection program. (2) That portion of an inspection interval described as an inspection period may be reduced or extended by as much as 1 year to enable an inspection to coincide with a plant outage. This adjustment shall not alter the rules and requirements for scheduling tion intervals. (d) For components inspected under Program B, the following shall apply: ( 1) Each inspection interval may be reduced or extended by as much as one year. Adjustments shall not cause successive intervals to be altered by more than one year from the original pattern of intervals.

If an inspection interval is extended, neither the start and end dates nor the in service inspection program for the successive interval need be revised. (2) Examinations may be performed to satisfy the requirements of the extended interval in conjunction with examinations performed to satisfy the requirements of the successive interval.

However, an examination performed to satisfy requirements of either the extended interval or the successive interval shall not be credited to both intervals.

(3) That portion of an inspection interval described as an inspection period may be reduced or extended by as much as one year to enable an inspection to coincide with a plant outage. This adjustment shall not alter the requirements for scheduling inspection intervals.

(4) The inspection interval for which an tion was performed shall be identified on examination records. (e) In addition to IWA-2430(c) and (d), for plants that are out of service continuously for 6 months or more, the inspection interval during which the outage occurred may be extended for a period equivalent to the outage and the original pattern of intervals extended accordingly for successive intervals. (j) The inspection intervals for items installed by repair !replacement activities shall coincide with as determined by the calendar years IWA-2431 2001 SECTION XI, DIVISION 1 IWA-2641 IWA-2431 Inspection Program A The inspection intervals shall comply with the ing, except as may be modified by IW A-2430(c):

1 st Inspection Interval -3 years following initial start of plant commercial service 2nd Inspection Interval -7 years following the 1st inspection interval 3rd Inspection Interval -13 years following the 2nd inspection interval 4th Inspection Interval -17 years following the 3rd inspection interval Successive Inspection Intervals

-follow IW A-2432 IWA-2432 Inspection Program B The inspection intervals shall comply with the ing, except as modified by IWA-2430(d):

i sf Inspection Interval -10 years following initial start of plant commercial service Successive Inspection intervals

-10 years following the previous inspection interval IWA-2440 APPLICATION OF CODE CASES IWA-2441 Section XI Code Cases (a) Code Cases to be used during a pre service or inservice inspection shall be identified in the tion Plan. (b) Code Cases shall be applicable to the Edition and Addenda specified in the Inspection Plan. (c) Code Cases shall be in effect at the time the Inspection Plan is filed with the regulatory and ment authorities having jurisdiction at the plant site except as provided in IWA-244 I (d). (d) Code Cases issued subsequent to filing the tion Plan may be proposed for use in amendments to the Inspection Plan. Code Cases approved continue IW A-2S00 EXTENT OF EXAMINATION Requirements for examination of welds apply only to welds joining items and not welds correcting flaws in base material (including core closure welds in casting), unless otherwise stated. IWA-2600 WELD REFERENCE SYSTEM IWA-2610 GENERAL A reference system shall be established for all welds and areas subject to surface or volumetric examination.

Each such weld and area shall be located and identified by a system of reference points. The system shall permit identification of each weld, location of each weld centerline, and designation of regular intervals along the length of the weld. IWA-2620 PIPING Requirements for piping are provided in III-4300.

The rules of I1I-4300 may also be applied to piping not within the scope of III-II 00. IWA-2630 VESSELS The requirements of Appendix A of Article 4 are acceptable for vessels examined in accordance with Article 4 of Section V. IWA-2640 OTHER COMPONENTS A reference system for component welds is given in IWA-2641.

A different system may be used provided it meets the requirements of IW A-261O. IW A -2641 Layout of Component Reference Points IWA-2641 GENERAL REQUIREMENTS IWA-2641 the top of the component.

The examination surfaces shall be identified as above or below the weld. (b) Longitudinal (Vertical)

Welds. Longitudinal welds shall be laid out from the center line of circumferential welds at the top end of the weld. The examination surface shaH be identified as clockwise or wise as viewed from the top of the component. (c) Nozzle-fa-Vessel Welds. The external reference circle shall have a sufficient whole number of inches radius so that the circle falls on the vessel external surface beyond the weld fillet. The internal reference circle shall have a sufficient whole number of inches radius so that the circle falls within 1;2 in. (13 mm) of the weld centerline.

Zero deg point on the weld shall be the top of the nozzle. The 0 deg point for welds of nozzles centered in heads shaH be located at the a deg axis of the vessel. Angular layout of the weld shall be made clockwise on the external surface, counterclockwise on the internal surface. Zero, 90, 180, and 270 deg lines shall be marked on all nozzle welds examined; 30 deg increment lines shall be marked on nozzle welds greater than 4 in. (102 mm) radius; 15 deg increment lines shall be marked on nozzle welds greater than 12 in. (305 mm) radius; 5 deg increment lines shall be marked on nozzle welds greater than 24 in. (610 mm) radius.