Information Notice 2011-01, Commercial Grade Dedication Issues Identified During NRC Inspections

From kanterella
(Redirected from ML103220180)
Jump to navigation Jump to search
Commercial Grade Dedication Issues Identified During NRC Inspections
ML103220180
Person / Time
Issue date: 02/15/2011
From: Kinneman J, Mcginty T, John Tappert
NRC/NMSS/FCSS, Division of Construction Inspection and Operational Programs, Division of Policy and Rulemaking
To:
References
IN-11-001
Download: ML103220180 (8)
v • d • e


UNITED STATES

NUCLEAR REGULATORY COMMISSION

OFFICE OF NUCLEAR REACTOR REGULATION

OFFICE OF NEW REACTORS

OFFICE OF NUCLEAR MATERIALS SAFETY AND SAFEGUARDS

WASHINGTON, DC 20555-0001 February 15, 2011 NRC INFORMATION NOTICE 2011-01: COMMERCIAL-GRADE DEDICATION ISSUES

IDENTIFIED DURING NRC INSPECTIONS

ADDRESSEES

All holders of an operating license or construction permit for a nuclear power reactor issued

under Title 10 of the Code of Federal Regulations (10 CFR) Part 50, Domestic Licensing of

Production and Utilization Facilities, except those who have permanently ceased operations

and have certified that fuel has been permanently removed from the reactor vessel.

All holders of or applicants for an early site permit, standard design certification, standard

design approval, manufacturing license, or combined license issued under 10 CFR Part 52, Licenses, Certifications, and Approvals for Nuclear Power Plants.

All holders of or applicants for a license for a fuel cycle facility issued pursuant to

10 CFR Part 70, Domestic Licensing of Special Nuclear Material, or 10 CFR Part 40,

Domestic Licensing of Source Material.

All vendors that supply basic components to NRC-licensed facilities.

PURPOSE

The U.S. Nuclear Regulatory Commission (NRC) is issuing this information notice (IN) to

summarize the NRC staffs observations and findings in the area of commercial-grade

dedication (CGD), as it applies to operating reactors, over the previous 2 years. The NRC

expects recipients to review the information and to consider actions, as appropriate, to review

lessons learned and avoid similar problems. Suggestions contained in this IN are not NRC

requirements; therefore, no specific action or written response is required.

DESCRIPTION OF CIRCUMSTANCES

This IN summarizes NRC staff findings from vendor inspections related to CGD performed over

the last 2 years. The NRC Office of Nuclear Reactor Regulation and Office of New Reactors

perform vendor inspections; one of the areas covered in these inspections is CGD. CGD is the

acceptance process undertaken to provide reasonable assurance that a commercial-grade item

to be used as a basic component will perform its intended safety function and, in this respect, is

deemed equivalent to an item designed and manufactured under a quality assurance (QA)

program under Appendix B, Quality Assurance Criteria for Nuclear Power Plants and Fuel

Reprocessing Plants, to 10 CFR Part 50, Domestic Licensing of Production and Utilization

Facilities. The following summary of NRC staff findings from vendor inspections done in the

last 2 years is divided into four main areas of concern: (1) lack of engineering justification

during the CGD process, (2) documentation, (3) vendor audits versus commercial-grade

surveys, and (4) sampling plans.

Lack of Engineering Justification during the CGD Process

NRC inspectors found several instances in which the vendor made design or engineering

changes during the dedication process without an engineering justification to validate these

changes.

During the review of a dedication package for a stainless steel ball bearing, the NRC inspectors

noted that an ElectroSpot test was performed instead of the required Rockwell hardness test for

critical metallic parts identified in a technical memo that was part of the dedication package.

The NRC inspectors determined that the ElectroSpot test provided reasonable assurance of the

material composition. However, the vendor performing the dedication did not have an

engineering justification for the acceptability of the ElectroSpot method instead of hardness

testing.

NRC inspectors also identified a lack of engineering justification while reviewing the dedication

package for a battery cell cover. This dedication package contained a table that defined the

critical characteristics (CCs) and dedication requirements for battery components. A previous

version of this table identified the battery cell cover as having a safety-related function, but the

current version identified the cover as nonsafety related. In this instance, the vendor failed to

provide engineering justification for downgrading the function of the battery cell cover from

safety related to nonsafety related.

Documentation of the CGD Process

In order to have an acceptable CGD program, the vendor must document the dedication

process, from the selection of the CCs to the acceptance criteria and acceptance methods used

to verify these CCs. Additionally, the purchaser or licensee should review and approve the

CGD package before the dedication of the item. CGD is an engineering process that concludes

with the reasonable assurance that a commercial-grade item to be used as a basic component

will perform its intended safety function. Each step taken during the dedication process should

be documented and auditable.

During review of a dedication package, the NRC inspectors noted that a locked rotor current test

could not be completed to the motors rated voltage because of testing equipment limitations.

The motor was tested by application of single-phase power to two of the motors terminals.

Institute of Electrical and Electronics Engineers (IEEE) Standard 112-2004, IEEE Standard

Test Procedure for Polyphase Induction Motors and Generators, permits this test to be

performed in lieu of mechanically locking the rotor to check the quality of squirrel-cage

machines. The motor successfully completed the test; however, the vendors dedication plan

failed to document the IEEE standard or list the single-phase test as an acceptance criterion.

During an inspection of a vendors CGD process, the NRC inspectors noted that all components

for an item were procured as commercial grade. The components that had CCs were identified. However, none of the CCs had any documented technical evaluation or acceptance method

bases.

The NRC inspectors identified one instance in which a vendors QA manual did not define or

document its dedication process as a controlled activity under Appendix B to 10 CFR Part 50.

The vendor also did not have procedures for implementing dedication activities. The vendor

performed dedication primarily by using Method 1 of Electric Power Research Institute

(EPRI) NP-5652, Guideline for the Utilization of Commercial Grade Items in Nuclear

Safety-Related Applications (NCIG-07), dated June 1, 1988. During the inspection, the NRC

staff noted that some of the dedication packages did not contain signoffs or records that

indicated the units were inspected by the in-process inspection department before being

certified by the QA department, as required by the vendors dedication process.

Vendor Audit versus Commercial-Grade Survey

A commercial-grade survey provides the purchaser with a method to take credit for the

documented programmatic controls that the supplier applies to a CC for a given item. Guidance

in EPRI NP-5652 states that the purchaser must confirm, as part of the survey, that the selected

commercial-grade items CCs are controlled under a documented quality program for the scope

of the activity. The NRC inspectors found various instances in which the vendor performed

limited-scope audits of the commercial subsuppliers QA program rather than a commercial- grade survey specific to certain CCs of an item. If Method 2 (see Attachment 1 diagram) will be

used as an acceptance method as part of the dedication of an item, the guidance in

EPRI NP-5652 states that a commercial-grade survey of the commercial supplier should be

performed.

During one vendor inspection, the NRC inspectors found that a vendors commercial-grade

survey failed to verify that the subvendors quality controls included specific processes, such as

material traceability and lot or batch controls, relevant to the CCs to support the sampling plan

during the dedication process.

The NRC inspectors also noted that one vendor performed a limited-scope audit of a

subsupplier that had an International Organization for Standardization (ISO) 9000 QA program.

The inspectors determined that the subsupplier should have been surveyed as part of the

dedication process because only organizations maintaining a QA program meeting the intent of

Appendix B to 10 CFR Part 50 are subject to audits. Suppliers maintaining commercial QA

programs are surveyed as part of the dedication process for a specific item. In this instance, the

vendor did not maintain a quality program that meets Appendix B to 10 CFR Part 50 and

therefore an audit was not acceptable.

Sampling Plans for Commercial-Grade Item Dedication

Sampling of commercial-grade items during dedication should provide reasonable assurance

that items inspected and tested conform to specification requirements. Sampling of items for

dedication can be controlled by establishing heat traceability of metallic material or establishing

lot/batch controls on the components. When neither can be established, documented sampling

plans can be established on an individual, item-specific basis for providing assurance of the

items suitability. Guidance on how sampling is used during commercial-grade item dedication and the selection of sampling plans is described in NRC Inspection Procedures (IP) 38703, Commercial Grade Dedication, and IP 43004, Inspection of Commercial-Grade Dedication

Programs.

NRC inspectors found cases during vendor inspections where vendor procedures did not

provide adequate guidance for the development of sampling plans. In two inspections, vendor

procedures did not provide adequate guidance for the development of sampling criteria to

include qualitative factors, such as safety significance of the item, adequacy of supplier controls, complexity of the item, and performance history to ensure adequate selection, documentation

and implementation of sampling plans.

BACKGROUND

The following NRC and industry documents address the CGD process:

Fraudulently Marketed Products, dated March 21, 1989 (Agencywide Documents

Access and Management System (ADAMS) Accession No. ML031140060)

  • GL 91-05, Licensee Commercial-Grade Procurement and Dedication Programs, dated

April 9, 1991 (ADAMS Accession No. ML031140508)

Nuclear Safety-Related Applications (NCIG-07), dated June 1, 1988

  • CGD material from the NRCs Workshops on Vendor Oversight 2008 Conference

(http://www.nrc.gov/reactors/new-reactors/oversight/quality-assurance/vendor- oversight/past/2008/index.html)

DISCUSSION

Licensees rely on CGD as a means of satisfying the requirements of Appendix B to

10 CFR Part 50 for procurement and acceptance of commercial-grade items and services for

use as basic components. An acceptable dedication program consists of the technical

evaluation that identifies the CCs and acceptance criteria for the item to be dedicated, the

acceptance methods that verify that the CCs have been met, and the documentation of the

steps taken during the dedication process. Complete documentation and auditable records of the rationale, justifications, and engineering analyses must be available as part of the dedication

package for the item or service being dedicated. In addition, purchaser or licensee review and

approval before the dedication of the item should be part of the process.

The references mentioned in the Background section of this IN contain specific guidance on

how to perform CGD. This IN does not endorse specific guidance or methods to perform

dedication. However, some stakeholders have expressed a concern that the NRCs

expectations on how dedication should be performed are not clear to the industry. As previous

NRC documents have stated, the following is a method acceptable to the staff for meeting the

regulations when performing dedication: implement the guidance of EPRI NP-5652, as modified

by the provisions contained in GL 89-02 and the requirements of 10 CFR Part 21, Reporting of

Defects and Noncompliance. In GL 89-02, the NRC conditionally endorsed the dedication

methods described in EPRI NP-5652. Guidance on the application of Appendix B to

10 CFR Part 50 appears in Regulatory Guide 1.28, Quality Assurance Program Criteria (Design

and Construction), and Regulatory Guide 1.33, Quality Assurance Program Requirements

(Operation). When properly implemented, these NRC and industry guidance documents

together provide reasonable assurance for the suitability of dedicated items to be used in safety- related applications.

The attached diagram, based on the guidance contained in EPRI NP-5652 and GL 89-02, can

be used to identify the general steps necessary to perform CGD. As the diagram indicates, during the technical evaluation the dedicating entity identifies the safety function, performance

requirements, part functional classification, and service conditions of the item; the CCs, including acceptance criteria; and dedication methods for verification of the acceptance criteria.

Some of the bases to identify CCs are design, material and performance characteristics; active

or passive safety-related functions; safety or nonsafety interfaces; and changes in design, material, or manufacturing process.

Guidance in EPRI NP-5652 encourages the dedicating entity to provide the most suitable or

appropriate acceptance method for each CC rather than attempting to use one method for an

entire dedication. For example, it may be appropriate to use Method 1 (see attached diagram)

to verify certain CCs during receipt inspection or post installation testing of an item, but to use

Methods 2 or 4 for other CCs that the supplier or manufacturer is being relied upon to verify for

that item. It should be noted that GL 89-02 restricts the use of Methods 2 and 4 as standalone

acceptance methods.

CONTACT

This IN requires no specific action or written response. Please direct any questions about this

matter to the technical contact listed below or to the appropriate Office of Nuclear Reactor

Regulation project manager.

/RA/ /RA/

Timothy J. McGinty, Director John D. Kinneman, Director

Division of Policy and Rulemaking Division of Fuel Cycle Safety and Safeguards

Office of Nuclear Reactor Regulation Office of Nuclear Material Safety and Safeguards

/RA/

John R. Tappert, Acting Director

Division of Construction Inspection

and Operational Programs

Office of New Reactors

Technical Contact:

Carla P. Roquecruz, NRR

301-415-1455 E-mail: carla.roquecruz@nrc.gov

Paul Prescott, NRR

301-415-3026 E-mail: paul.prescott@nrc.gov

Note: NRC generic communications may be found on the NRC public Web site, http://www.nrc.gov, under Electronic Reading Room/Document Collections.

Attachment 1: General Steps to Perform Commercial-Grade Dedication

CONTACT

This IN requires no specific action or written response. Please direct any questions about this

matter to the technical contact listed below or to the appropriate Office of Nuclear Reactor

Regulation project manager.

/RA/ /RA/

Timothy J. McGinty, Director John D. Kinneman, Director

Division of Policy and Rulemaking Division of Fuel Cycle Safety and Safeguards

Office of Nuclear Reactor Regulation Office of Nuclear Material Safety and Safeguards

/RA/

John R. Tappert, Acting Director

Division of Construction Inspection

and Operational Programs

Office of New Reactors

Technical Contact:

Carla P. Roquecruz, NRR

301-415-1455 E-mail: Carla.Roquecruz@nrc.gov

Paul Prescott, NRR

301-415-3026 E-mail: Paul.Prescott@nrc.gov

Note: NRC generic communications may be found on the NRC public Web site, http://www.nrc.gov, under Electronic Reading Room/Document Collections.

Attachment 1: General steps to perform commercial grade dedication

ADAMS Accession Number: ML103220180 TAC ME4654 OFFICE EQVB:DE:NRR EQVB:DE:NRR Tech Editor BC:EQVB:NRR D:DE:NRR BC:CQVB:NRO

NAME CRoquecruz PPrescott KAzariah-Kribbs MMurphy PHiland RRasmussen

DATE 12/14 /2010 12/15/2010 11 /24 / 2010 e-mail 12/17/2010 01/20/2011 1 / 10 /2011 e-mail

OFFICE GCHEA:OGC LA:PGCB:NRR PM:PGCB:NRR PM:PGCB:NRR BC:PGCB:NRR D:FCSS:NMSS

NAME EWilliamson CHawes CMH BPurnell ARussell SRosenberg JKinneman

DATE 01/19/2011 01/24/2011 01/21/2011 01/24/2011 02 /04 /2011 02 /08 /2011 OFFICE D:DCIP:NRO D:DPR:NRR

NAME JTappert TMcGinty

DATE 02 /14/2011 02/05/2011 OFFICIAL RECORD COPY

Attachment 1: General Steps to Perform Commercial-Grade Dedication*

IDENTIFY ITEMS BY TECHNICAL

EVALUATION

NO PROCURE ITEM

DOES ITEM PERFORM

SAFETY FUNCTION? NONSAFETY

YES

PROCURE ITEM AS NO

CAN ITEM

BASIC COMPONENT BE DEDICATED?

YES

IDENTIFY CRITICAL

CHARACTERISTICS

DOCUMENT RESULTS:

  • SAFETY FUNCTION/SIGNIFICANCE
  • DESIGN MARGIN
  • CREDIBLE FAILURE MODES TECHNICAL
  • DESIGN CHARACTERISTICS EVALUATION

SELECT ACCEPTANCE ACCEPTANCE

METHOD(S) METHODS

METHOD 1: METHOD 2: METHOD 3: METHOD 4:

SPECIAL TESTS VENDOR SOURCE VENDOR

& INSPECTIONS SURVEY VERIFICAION PERFORMANCE

Per Generic Letter 89-02, Methods 2 & 4 need

to be used in conjunction with another Method

  • This is a graphical representation of the commercial-grade dedication process used for illustrative purposes only

and based on the guidance in Electric Power Research Institute NP-5652, Guideline for the Utilization of

Commercial Grade Items in Nuclear Safety-Related Applications (NCIG-07), dated June 1, 1988.


Retrieved from "https://kanterella.com/w/index.php?title=Information_Notice_2011-01,_Commercial_Grade_Dedication_Issues_Identified_During_NRC_Inspections&oldid=2124499"