ML18106B002

From kanterella
Revision as of 21:53, 11 December 2018 by StriderTol (talk | contribs) (Created page by program invented by StriderTol)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
LER 98-015-01:on 980924,improper Installation of Test Equipment to RPS Occurred.Caused by Inadequate 10CFR50.59 Applicability Reviews During Past Revs.Revised Procedures. with 981217 Ltr
ML18106B002
Person / Time
Site: Salem PSEG icon.png
Issue date: 12/17/1998
From: BAKKEN A C, THOMAS B J
Public Service Enterprise Group
To:
NRC OFFICE OF INFORMATION RESOURCES MANAGEMENT (IRM)
References
LER-98-015, LER-98-15, LR-N980576, NUDOCS 9812310135
Download: ML18106B002 (7)


Text

I \/ e

  • Public Service Electric and Gas Company P.O. Box 236. Hancocks Bridge, New Jersey 08038-0236 Nuclear Buslnes5 Unit U. S. Nuclear Regulatory Commission Document Control Desk Washington, DC 20555 LER 272/98-015-01 DECl T SB LR-N980576 SALEM GENERATING STATION-UNIT 1 FACILITY OPERATING LICENSE NO. DPR-70 DOCKET NO. 50-272 Gentlemen:

This Supplemental Licensee Event Report entitled "Improper Installation of Test Equipment to the Reactor Protection System" is being submitted pursuant to the requirements of the Code of Federal Regulations 10CFR50.73(a)(2)(i)(B) and 1OCFR50.73(a)(2)(ii)(B).

Attachment BJT C Distribution LER File 3.7 9812310135 981217 PDR ADOCK 05000272 6 PDR The pcMer is in p.ir hands. Sincerely, A. C. Bakken 111 General Manager -Salem Operations

--95-2168 REV. 6/94 NRC FORM 366 U.S. NUCLEAR REGULATORY COMMISSION APPROVED BY OMB NO. 3150-0104 EXPIRES 06/30/2001 (6-19981 Estimated burden per response to comply with this mandaloly information collection request so hrs. Reported lessons learned are incorporated into LICENSEE EVENT REPORT (LER) the licensim,i process and fed back to induslly.

Forward comments regarding burden estimate to the Records Management Branch (T-6 F3;] U.S. Nuclear Regulaloly Commission, Washington, DC 2055S-0001, a 'to the (See reverse for required number of Paperwork Reduction Project Office of Management and Budget, Washington, DC 20503. If an information collection does not display digits/characters f.or each block) a currently OMB conb"ol number, the NRC may not conduct or sponsor, and a person 1s not required to respond to, the information collection.

FACILITY NAME (11 DOCKET NUMBER 121 PAGEl31 Salem Unit 1 05000272 1 OF 6 TrnEl41 Improper Installation of Test Equipment to the Reactor Protection System CVl:lllT nATC l!>I CD ..,, , .. 11 :1 DCD "!AT 171 nTMS:A CAl"ll ITIS:li::

II

.... , ... MON DAY YEAR YEAR SEQUENTIAL REVISION MONTH DAY YEAR FACILITY NAME DOCKET NUMBER Salem Unit 2 05000311 09 24 98 98 015 01 12 17 98 FACILITY NAME DOCKET NUMBER OPERATIN -r> ,. .. AS:PnAT '" "I DI ...... ,.,..,T Tn TL.IC Deni ,..., 1n ..,., .. 5* trh--*-..... nr ----* 111\ Mode 1 20.2201(bJ 20.2203(a)(2)(v) x 50. 731all211il

50. 73(a)(2)(viiiJ POWER 20.22031all 1 J 20.2203(a)(3)(i) x 50. 731all211iiJ
50. 73(a)(2)(xJ LEVEL 100 20.2203(a)(2)(i) 20.2203(a)(3J(iiJ
50. 73(a)(2Jliii) 73.71 20.2203(a)(2)(iil 20.2203(a)(4J
50. 73(a)(2)(iv)

OTHER 20.2203(a)(2)(iiil 50.36Ccll1 J 50. 73(a)(2J(v)

Specify in Abstract below 20.2203(a)(2)(ivJ 50.36(c)(2)

50. 73(a)(2)(viil or in NRC Form 366A I rn ... T* ........ ,.. .. TL.I"'" I., .. /1.,, NAME TELEPHONE NUMBER (Include Area Codel Brian J. Thomas, Licensing Engineer 609-339-2022

........ i:i 'S: ""'c I IMC cnD CAl"U CAHl*nC 11\1 TUI., 11':1\ CAUSE SYSTEM COMPONENT MANUFACTURER REPORTABLE CAUSE SYSTEM COMPONENT MANUFACTURER REPORTABLE TO EPIX TO EPIX !i::llDDI RS:PnRT 11A\ EXPECTED MnMTU n.o.v VFAD 'YES (If yes, complete EXPECTED SUBMISSION DATE). Ix !No ABSTRACT (Limit to 1400 spaces, i.e., approximately 15 single-spaced typewritten lines) (16) A review of the procedure for the connection of test equipment for collection of State Point data identified that test leads from the four channels of Reactor Control and Protection system were connected to switch boxes that had not been qualified to the same requirements as the Reactor Control and Protection system. Specifically, these switchboxes had not been evaluated to determine their capability to resist multiple channel failures, the most credible being a seismic event. The connections to the Reactor Control and Protectior:i system were from the non-isolated portion of the system and were not provided with isolation devices as described in the Salem Updated Final Safety Analysis Report (UFSAR). Based on this, the channels connected to the switchboxes should have been declared inoperable with the test equipment installed since a proper evaluation was not performed prior to installing the test equipment.

The cause is attributed to inadequate 1 OCFR50.59 applicability reviews during past revisions and the original issuance of the State Point Data procedure due to inadequate program guidance regarding the applicability of 1 OCFR50.59 to maintenance and test equipment.

A contributing factor to this event is ineffective corrective actions from similar events. This event is reportable under 10CFR50.73(a)(2)(i)(B), any condition prohibited by the plant's Technical Specifications and 1 73(a)(2)(ii)(8) rnnrfitinn n11tsirf P. the cf P.sirm of the NRC FORM 366 (6-1998)

\ ' .j NRC FORM 366A U.S. NUCLEAR REGULATORY COMMISSION (6-1998) LICENSEE EVENT REPORT (LER) TEXT CONTINUATION FACILITY NAME (1) SALEM UNIT 1 DOCKET (2) NUMBER (2) 05000272 TEXT (If more space is required, use additional copies of NRC Form 366AJ (17) PLANT AND SYSTEM IDENTIFICATION Westinghouse

-Pressurized Water Reactor Reactor Control and Protection System {JC/-}* LER NUMBER (6) l SEQUENTIAL I REVISION YEAR NUMBER . NUMBER 98 -015 -01 PAGE!3l 2 OF 6

  • Energy Industry Identification System (EllS) codes and component function identifier codes appear as {SS/CCC}.

CONDITIONS PRIOR TO OCCURRENCE At the time of discovery, Salem Unit 1 and Unit 2 were in Mode 1. DESCRIPTION OF OCCURRENCE A review of the procedure for the connection of test equipment for collection of State Point data identified that test leads from the four channels of Reactor Control and Protection system were connected to switch boxes that had not been qualified to the same requirements as the Reactor Control and Protection system. Specifically, these switchboxes had not been evaluated to determine their capability to resist multiple channel failures, the most credible being a seismic event. The connections to the Reactor Control and Protection system were from the non-isolated portion of the system and were not provided with isolation devices as described in the Salem Updated Final Safety Analysis Report (UFSAR). Specifically the UFSAR states that, "the design criterion used to assure* electrical isolation is that no analog signal which is required for initiation of reactor protection or engineered safety feature actuation is allowed to leave a set of protection channels.

Where protection signal intelligence is required for other than protection functions an isolation amplifier is used to transmit the intelligence." Based on this, the channels connected to the switchboxes should have been declared inoperable with the test equipment installed since a proper evaluation was not performed prior to installing the test equipment.

Based on the above, this event is reportable under 10CFR50.73(a)(2)(i)(B), any condition prohibited by the plant's Technical Specifications and 10CFR50.73(a)(2)(ii)(B), any condition that was outside the design basis of the plant. NRC FORM 366A (6-1998)

NRC FORM 366A U.S. NUCLEAR REGULATORY COMMISSION (6-1998) LICENSEE EVENT REPORT (LER) FACILITY NAME 111 SALEM UNIT 1 TEXT CONTINUATION DOCKET 121 NUMBER (21 05000272 TEXT (If more space is required, use additional copies of NRC Form 366AJ (17) CAUSE OF OCCURRENCE LER NUMBER (6) PAGE (3) I SEQUENTIAL I REVISION YEAR NUMBER NUMBER 3 OF 6 98 -015 --01 The cause is attributed to inadequate 1 OCFR50.59 applicability reviews during past revisions and the original issuance of the State Point Data procedure due to inadequate program guidance regarding the applicability of 1 OCFR50.59 to maintenance and test equipment.

A contributing factor to this event is ineffective corrective actions from similar events as outlined in the following section. PRIOR SIMILAR OCCURRENCES A review of LERs for the past two years identified the following similar occurrences concerning the installation of Maintenance and Test Equipment (M&TE) to operable plant systems: LER 272/97-013-00: "Failure to Meet Technical Specification 3.8.1.1 Action B." This event consisted of returning the 2A Emergency Diesel Generator (EOG) to operable status with the test equipment hooked up. Restoring the EOG to operable status with the test equipment installed had not been previously evaluated and was contrary to the operations procedure.

This event was attributed to personnel error for intentionally leaving the test equipment in place when declaring the EOG operable contrary to the procedure requirement that directed the removal of the test equipment.

A corrective action from the LER was to provide appropriate direction for the installation of temporary test in.strumentation into operable plant equipment.

This corrective action assessed the for control of temporary modifications and the maintenance department troubleshooting procedure and determined that adequate guidance was provided in these procedures to ensure that installation of M&TE on operable systems would be evaluated under the 10CFR50.59 process. This assessment also identified enhancements to centralize the guidance for evaluating the installation of M&TE into a single document, which has not been completed.

LER 311/97-014-00: "Manual Reactor Trip From 100% Power Following Loss of Both Operating Steam Generator Feed Pumps." A circuit card in the Westrac Data Acquisition System (DAS) failed causing feedwater header pressure to indicate approximately 150 psig below actual. The advanced digital feedwater control system (ADFCS) responded by increasing feedwater pump speed causing feedwater flow to increase to more than 120% of full flow value. This caused feedwater pump suction pressure .to drop leading to the automatic trip of both feedwater pumps. The cause of the event was attributed to the failure of the Westrac DAS circuit card. Although the 1 OCFR50.59 evaluation that had been performed discussed the modification to install the ADFCS including design, installation and testing, the potential failure modes of the M&TE were not discussed.

The corrective actions associated with this LER consisted of addressing the specific impact of the Westrac DAS on the AFDCS and the installation of M&TE during modification testing. NRC FORM 366A (6-1998)

NRC FORM 366A REGULATORY COMMISSION (6-1998) U.S. NUCLEAR FACILITY NAME 111 LICENSEE EVENT REPORT (LER) TEXT CONTINUATION DOCKET 121 NUMBER 121 LER NUMBER 161 PAGE 131 SALEM UNIT 1 05000272 I SEQUENTIAL I REVISION YEAR NUMBER NUMBER 4 OF 6 98 -015 --01 TEXT (If more space is required, use additional copies of NRC Form 366AJ 1171 PRIOR SIMILAR OCCURRENCES (conf d) LER 311/98-001-00: "Failure to Meet Technical Specification

3.3.7 Table

3.3-11 Item 19-RVLIS.n The Reactor Vessel Level Instrumentation System (RVLIS) was considered operable with data system acquisition system (DAS) equipment connected to the system. The DAS instrumentation provided inadequate isolation between the non-safety related DAS and the RVLIS channels.

Therefore, the RVLIS could not be considered operable with the test equipment installed.

The cause was attributed to the failure to identify that the initial 50.59 evaluation for the RVLIS procedure installation assumed that during performance of the procedure, RVLIS would be considered . inoperable.

The corrective actions associated with this LER provided additional guidance in procedure SC.SE-AP.ZZ-0002(0), "Conduct of Testing," to assess the impact of M&TE during infrequently performed tests. LER 272198-011-00: "Improper Isolation of the Single Cell Battery Charger from the 125 VDC Battery." The charging of cell 47 of the 1A 125 VDC battery using the single cell battery charger was identified as having been accomplished without proper evaluation for the isolation of the battery charger from the Class-1E 125 VDC battery. Although the single cell battery charger was installed in accordance with an existing maintenance procedure, proper analysis was not performed in accordance with the requirements of 1 OCFR50.59 to evaluate the electrical isolation between the single cell charger and the safety related battery. The corrective actions assoCiated with this LER were to revise the program guidance document for 1 OCFR50.59 to include examples concerning the connection of temporary equipment to operable systems, to include this issue in 10CFR50.59 refresher training beginning in July 1998, and to review maintenance procedures to determine if other procedures allowed temporary equipment to be installed on operable systems and then perform a review to determine if the connection of the temporary equipment had been adequately evaluated for system operation.

The revision to the 1 OCFR50.59 program guidance document was completed in August 1998. The discussion of this LER was included in the 1 OCFR50.59 refresher training cycle that began in July 1998. The review of maintenance procedures to determine other instances of connecting temporary equipment was completed in August 1998 and identified several procedures that connected temporary equipment to operable systems. However, the review to determine if the effect of the temporary equipment had been adequately evaluated has not been completed.

As a result of the review of maintenance procedures, the procedure for the installation of test equipment for the collection of State Point Data had been identified as a procedure requiring further evaluation for system impact. NRC FORM 366A (6-1998)

'/ NRC FORM 366A U.S. NUCLEAR REGULATORY COMMISSION (6-1998) LICENSEE EVENT REPORT (LER) TEXT CONTINUATION FA'CILITY NAME 111 SALEM UNIT 1 DOCKET 121 NUMBER 121 05000272 TEXT (If more space is required, use additional copies of NRC Form 366AJ 1171 PRIOR SIMILAR OCCURRENCES (cont'd) LER NUMBER 161 PAGE 131 I SEQUENTIAL I REVISION YEAR NUMBER NUMBER 5 OF 6 98 -015 --01 Upon review of the LERs above and the associated corrective actions, the root cause investigation identified a lack of commitment to program implementation.

Although events at Salem and in the industry indicated a need for the review of the usage of M&TE when connecting equipment to operable systems, a programmatic approach that would provide a consistent approach to personnel for assessing M&TE usage had not been developed.

Although corrective actions were identified in previous event investigations that may have prevented this event, the deferral of corrective actions in the corrective action program by closing activities to new tasks led to untimely implementation of corrective actions. The Corrective Action Program guidance regarding the closure of corrective actions did not prohibit the closure of an existing task to a new task, which provided a method of deferring implementation of an action without receiving the appropriate management approval.

On October 15, 1998, revision 16 of procedure OQ06(Q), "Corrective Action Program," was issued which provided further guidance for the closure of one corrective action task (CRCA) to another CRCA. SAFETY CONSEQUENCES AND IMPLICATIONS The affect of the actual test equipment configuration used during statepoint data collection was reviewed to assess the impact to Reactor Control and Protection system. The only plausible failure that was determined to have an affect on the Reactor Control and Protection channels was if instrument loops shorted together during a seismic event. Testing identified that if the positive signal of one loop shorted to the negative of the other loop, large spikes in voltage occurred.

This caused the voltage in one instrument loop to drop while the voltage in the other loop increased.

Therefore, the occurrence of a seismic event while the test equipment was installed may have had the ability to affect multiple channels of the Reactor Control and Protection system with the test equipment installed.

Since no design basis seismic event has occurred at Salem Station,_

there were no safety consequences associated with this event. NRC FORM 366A (6-1998)

NRC FORM 366A (6-19981 * .FA'CILITY NAME (1) SALEM UNIT 1 LICENSEE EVENT REPORT CLER) TEXT CONTINUATION DOCKET 121 NUMBER 121 U.S. NUCLEAR REGULATORY COMMISSION LER NUMBER (6) PAGEl31 I SEQUENTIAL I REVISION 05000272 YEAR NUMBER NUMBER . 6 OF 6 98 -015 --01 TEXT (If more space is required, use additional copies of NRC i=orm 366AJ (171 CORRECTIVE ACTIONS 1. The procedures for the installation of test equipment for the collection of State Point Data for Salem Units 1 and 2 were placed on administrative hold to prevent use of the procedure until resolution of the connection of the test equipment to the Reactor Control and Protection system is resolved.

2. As committed in LER 272/98-011-00, review of maintenance procedures has been performed to determine if other procedures allow temporary equipment to be installed on operable systems. As a result of this review, ten (10) procedures (in addition to the State Point Data procedures) were placed on hold to prevent their use until the assessment of the M& TE connection is completed.

Nine (9) of the procedures placed on hold have been reviewed for the M& TE applications (the Statepoint Data Procedures and one other procedure remain on hold). The assessment of the current method for connecting the M&TE as directed in these nine procedures revealed no problems.

3. On October 15, 1998, revision 16 of procedure NC.NA-AP.ZZ-0006(0), "Corrective Action Program," was issued which provided further guidance for the closure of one corrective action task (CRCA) to another CRCA. 4. As committed in LER 272198-011-00, the "1 OCFR50.59 Program Guidance" procedure was revised in August 1998 to include examples concerning the connection of temporary equipment to operable systems when performing 1 OCFR50.59 reviews. 5. As committed in LER 272/98-011-00, the subject of connection of M&TE to operable was included in the 1 OCFR50.59 refresher training cycle starting in July 1998. NRC FORM 366A (6-19981