Revision as of 02:58, 11 April 2019

Text

2014-08 Draft Operating Test
	ML14279A079
Person / Time
Site:	Diablo Canyon
Issue date:	06/20/2014
From:	Vincent Gaddy; Operations Branch IV
To:	; Pacific Gas & Electric Co
	laura hurley
References
	50-275/14-OL, 50-323/14-OL
	Download: ML14279A079 (402)
	v • d • e

N UCLEAR P OWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE M EASURE AUTHOR:L ISAT ORIBIOD ATE:06/20/2014OPERATIONSR EPRESENTATIVE

A BDULK ADIRD ATE:06/20/2014R EV.0 Number: NRCL121-A1 Title: DETERMINE ULTIMATE HEAT SINK TEMPERATURE Examinee: Evaluator: Print Signature Date Testing Method: Perform X Simulate Results: Sat Unsat Total Time: minutes Comments:

References:

STP I-1A, Routine Shift Checks Required by Licenses, Attachment 12.1, Rev. 127 Technical Specifications, DCPP Units 1 & 2 Alternate Path: Yes No X Time Critical: Yes No X Time Allotment: 10 minutes Critical Steps: 2.3, 2.7, 3.4 Job Designation: RO Rev Comments: modified from bank LJACO02R Gen KA / Rating: G2.1.23 - Ability to perform specific system and integrated plant procedures during all modes of plant operation. 4.3 Note: This is an admin JPM (RO), intended for the classroom setting.

JPM TITLE: DETERMIN E ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: NRCL121-A 1 EVALUATOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

Unit 1 STP I

-1A, MODE 1 Shift Checks, Step 37 (SR 3.7.9.2) Initial Conditions GIVEN: Unit 1 is at 50% power CWP 1-2 out of service for replacement of damaged screens Unit 2 is in day 14 of a refueling outage.

Current plant conditions for the Circ Water and ASW systems are as follows: Component Status Current Ocean Temperature CWP 1-1 In-service TI-311 Out of Calibration CWP 1-2 Cleared TI-328 60.1F ASW Pp 1-1 In-service to CCW HX 1-1 TI-1484 61.4F ASW Pp 1-2 In-STBY TI-1485 60.2F CWP 2-1 Cleared TI-311 60.3F CWP 2-2 Cleared TI-328 60.4F ASW Pp 2-1 In-service to CCW HX 2-1 TI-1484 61.5F ASW Pp 2-2 Cleared TI-1485 60.4 F Initiating Cue: Shift Forman directs you to determine the Ultimate Heat Sink Temperature, using STP I-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 37.

DO NOT READ TASK STANDARD TO EXAMINEE Task Standard:

Using step 37, determined ocean temperature is 62.1°F and needs to be recorded every 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months .

NRCL121-A1 PAGE 2 OF 5 R EV. 0 JPM TITLE: DETERMIN E ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: NRCL121-A 1 EVALUATOR WORKSHEET Start Time:

Step Expected Operator Actions

1. Obtain the correct procedure.

1.1 Obtains

STP I

-1A, Attachment 12.1.

Sat: ______ Unsat _______

Comment: 2.0B** Determine ocean temperature

2.1 Reads

NOTE prior to step 37.a.

2.2 "N/A" checked for step 37.a (Method 1) (TI-311 is Out of Service and CWP 1-2 is not running)

2.3 1BPerformed

step 37.b (Method 2), and recorded Pacific Ocean water temperature, 61.4F (TI-1484).**

2.4 2B"N/A" checked for TI-1485, (ASW Pp 1-2 not running).

2.5 3BDetermined

61.4F is the highest available indication. 2.6 4BAdds 0.7 F 2.7 5BRecorded 62.1F as the corrected ocean temperature. **

2.8 Checks

"N/A" for step 37.c (Method 3) Sat: ______ Unsat _______

Comment: NRCL121-A1 PAGE 3 OF 5 R EV. 0 JPM TITLE: DETERMIN E ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: NRCL121-A 1 EVALUATOR WORKSHEET 3. Document monitoring requirements 3.1 Read NOTE prior to step 37.d.

3.2 Checked

"N/A" for step 37.d

3.3 Checked

step 37.

e.1) t o inform SFM to review SR 3.7.9.2

3.4 Checked

step 37.d.2) due to ocean temperature determined to be greater than 62°F but less than 64° F, and that temperatures need to be recorded every 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months .** 3.5 N/A step 37.f Sat: ______ Unsat _______

Comment:

Stop Time:

Total Time: (Enter total time on the cover page)

Follow up Question Documentation

Question: ____________________________________________________________________

______________________________________________________________________________

Response: ____________________________________________________________________

______________________________________________________________________________

NRCL121-A1 PAGE 4 OF 5 R EV. 0 69-20232 01/27/14 Page 15 of 26 STP I-1A (UNIT 1) ATTACHMENT 12.1 TITLE: MODE 1 Shift Checklist STP_I-1Au1r27.DOC 06 0515.1508 APPL MODE TECH SPEC

REFERENCE A. CHECK / VERIFICATION FROM CONTROL ROOM PERF 37.Determine the Ultimate Heat Sink (UHS) temperature using one of the following methods:NOTE: Temperature indicators are only available whentheir associated pumps are running.

a.Method 1 - Record Pacific Ocean water temp as readon the following indicators:N/A [ X ] ______ TI-311 (T2400A) (CWP 1-1) _______FN/A [ ] TI-328 (T2401A) (CWP 1-2) _______FN/A [ ] Record the highest of the available indicators. F Instrument Error Correction 1.9 F Add the highest available indicator reading and the Instrument Error Correction. F b.Method 2 - Record Pacific Ocean water temp on thefollowing indicators:N/A [ ] __NRC__ TI-1484 (ASWP 1-1) _61.4__FN/A [ ] TI-1485 (ASWP 1-2) _______FN/A [X ] Record the highest of the available indicators.61.4 F Instrument Error Correction 0.7 F Add the highest available indicator reading and the Instrument Error Correction.62.1°F 1 SR 3.7.9.2 69-20232 01/27/14 Page 16 of 26 STP I-1A (UNIT 1) ATTACHMENT 12.1 TITLE: MODE 1 Shift Checklist STP_I-1Au1r27.DOC 06 0515.1508 APPL MODE TECH SPEC

REFERENCE A. CHECK / VERIFICATION FROM CONTROL ROOM PERF c.Method 3 - If Method 1 and Method 2 are notavailable, M&TE may be used.N/A [X ] ______ Instrument Used: ____________________Cal Due Date: ____________________Reading using M&TE F Uncertainty of M&TE F Add M&TE ocean temp and uncertainty F NOTE: Tech Spec Bases B3.7.9 specifies that the UHS is common to both units. Therefore any required action due to elevated ocean water temp would apply to both units depending on mode requirements. Notify the Unit 2 SFM as required.

d.IF corrected ocean temp is > [60F] AND [62F],THEN perform the following:N/A [ X]

1)Notify SFM to review Tech Spec SR 3.7.9.2.______ 2)Record ocean temp every 12 hours1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months .

______ e.IF corrected ocean temp is > [62F] AND [64F],THEN perform the following:N/A [ ] 1)Notify SFM to review Tech Spec SR 3.7.9.2.

_NRC_ 2)Record ocean temp every 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months .

_NRC_ f.IF corrected ocean temp is > [64F],THEN place both CCW HXs in service:N/A [ X ] ______ SR 3.7.9.2 (Continued) 1 EXAMINEE CUE SHEET JPM NUMBER: NRCL121-A1 Initial Conditions: GIVEN: Unit 1 is at 50% power CWP 1-2 out of service for replacement of damaged screens Unit 2 is in day 14 of a refueling outage. Current plant conditions for the Circ Water and ASW systems are as follows: Component Status Current Ocean Temperature CWP 1-1 In-service TI-311 Out of Calibration CWP 1-2 Cleared TI-328 60.1F ASW Pp 1-1 In-service to CCW HX 1-1 TI-1484 61.4F ASW Pp 1-2 In-STBY TI-1485 60.2F CWP 2-1 Cleared TI-311 60.3F CWP 2-2 Cleared TI-328 60.4F ASW Pp 2-1 In-service to CCW HX 2-1 TI-1484 61.5F ASW Pp 2-2 Cleared TI-1485 60.4 F Initiating Cue: Shift Forman directs you to determine the Ultimate Heat Sink Temperature, using STP I-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 37.

NRCL121-A1 PAGE 5 OF 5 R EV. 0 69-20232 01/27/14 Page 15 of 26 STP I-1A (UNIT 1) ATTACHMENT 12.1 TITLE: MODE 1 Shift Checklist STP_I-1Au1r27.DOC 06 0515.1508 APPL MODE TECH SPEC

REFERENCE A. CHECK / VERIFICATION FROM CONTROL ROOM PERF 37.Determine the Ultimate Heat Sink (UHS) temperatur e using one of the following me thods: NOTE: Te mperature indicators are only available whentheir associated pumps are running.a.Method 1 - Record Pacific Ocean water temp as readon the following in dicators: N/A [ ] ______ TI-311 (T2400A) (CWP 1-1) _______ FN/A [ ] TI-328 (T2401A) (CWP 1-2) _______ FN/A [ ] Record the highest of the available indicators. F Instrument Error Correction 1.9 F Add the highest available i ndicator reading and the Instrument Error Correction. F b.Method 2 - Record Pacific Ocean water temp on thefollowing indi cators: N/A [ ] ______ TI-1484 (ASWP 1-1) _______F N/A [ ] TI-1485 (ASWP 1-2) _______F N/A [ ] Record the highest of the available indicators. F Instrument Error Correction 0.7 F Add the highest available i ndicator reading and the Instrument Error Correction.

°F 1 SR 3.7.9.2 69-20232 01/27/14 Page 16 of 26 STP I-1A (UNIT 1) ATTACHMENT 12.1 TITLE: MODE 1 Shift Checklist STP_I-1Au1r27.DOC 06 0515.1508 APPL MODE TECH SPEC

REFERENCE A. CHECK / VERIFICATION FROM CONTROL ROOM PERF c.Method 3 - If Method 1 and Method 2 ar e notavailable, M&TE may be used.N/A [ ] ______ Instrument Used: ____________________Cal Due Date: ____________________ Reading usin g M&TE F Uncertainty of M&TE F Add M&TE ocean temp a nd uncertainty F NOTE: Tech Spec Bases B3.7.9 specifies that the UHS is common to both units. Therefore any required action due to elevated ocean water temp would apply to both units depending on mode requirements. Notify the Unit 2 SFM as required.

d.IF corrected ocean temp is > [60F] AND [62 F],THEN perform the followi ng: N/A [ ] 1)Notify SFM to review Tech Spec SR 3.7.9.2.______ 2)Record ocean temp every 12 hours1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months .

______ e.IF corrected ocean temp is > [62F] AND [64 F],THEN perform the followi ng: N/A [ ] 1)Notify SFM to review Tech Spec SR 3.7.9.2.______ 2)Record ocean temp every 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months .______ f.IF corrected ocean temp is > [64 F],THEN place both CCW HXs in service:N/A [ ] ______ SR 3.7.9.2 (Continued) 1 NUCLEAR POWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE MEASURE Number: LJACO-02R Title: DETERMINE ULTIMATE HEAT SINK TEMPERATURE Examinee:

Evaluator:

Print Signature Date Results: Sat Unsat Total Time: minutes Comments: Rev 4A an EC was performed to change to current rev and step of I-1A approved by the ILT supervisor. Also changed ASW to 61.5 degrees per TIP 20048 act 16.

References:

STP I-1A, Routine Shift Checks Required by Licenses, Attachment 12.1, Step 37 (SR 3.7.9.2), Rev. 121 Technical Specifications, DCPP Units 1 &

2 Alternate Path:

Yes X No Time Critical:

Yes No X Time Allotment:

10 Minutes Critical Steps:

2, 3 Job Designation:

RO Task Number:

G2.1.23 Rating: 4.3 AUTHOR: DAVID RICHARDS / CHARLES HIBBARD DATE: 05/04/11 REVIEWED B Y: JOHN P. LYLE DATE: 05/04/11 TRAINING SUPERVISOR APPROVED B Y: KEN JOHNSTON DATE: 05/05/11 MANAGER - OPERATIONS R EV. 4A JPM TITLE: DETERMINE ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: LJACO-02R INSTRUCTOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

STP I-1A, MODE 1 Shift Checks, Step 37 (SR 3.7.9.2) Initial Conditions:

Unit 1 is at 50% power with CWP 1-2 out of service for replacement of damaged screens. Unit 2 is in day 14 of a refueling outage. Current plant conditions for the Circ Water and ASW systems are as follows: Component Status Current Ocean Water Temperature CWP 1-1 In-service TI-311 61F CWP 1-2 Cleared TI-328 61F ASW Pp 1-1 In-service to CCW HX 1-1 TI-1484 61.5F ASW Pp 1-2 In-STBY TI-1485 60F CWP 2-1 Cleared TI-311 61F CWP 2-2 Cleared TI-328 61F ASW Pp 2-1 In-service to CCW HX 2-1 TI-1484 61.5F ASW Pp 2-2 Cleared TI-1485 61F Initiating Cu e: Shift Forman directs you to determine the Ultimate Heat Sink Temperature, using STP I-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 37.

DO NOT READ TASK STANDARD TO EXAMINEE Task Standard:

Ultimate Heat Sink temperature is determined based on given information and Shift Foreman informed of results.

DOCCONTENT.dll PAGE 2 OF 5 R EV. 4A JPM TITLE: DETERMINE ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: LJACO-02R INSTRUCTOR WORKSHEET Start Time: StepExpected Operator Actions

1. Obtains correct procedure.

1.1 Obtains

STP I-1A, Attachment 12.1. Note: Provide exam copy of STP I-1A, Attachment 12.1, Step 3 7. Step was: Sat: _______ Unsat _______*

2. **Determines UHS temperature using method 1.

2.1 Reads

NOTE prior to step 37.a. 2.2 Records the Pacific Ocean water temperature , 61F on TI-311.** 2.3 Checks "N/A" for TI-328, since CWP 1-2 is not running.

2.4 Determines

that 61F is the highest available indication, and writes that value on the data sheet.

- 2.5 Adds 1.9F, and writes 62.9F as the corrected ocean temperature.

Initials step 37.a.** 2.6 Checks "N/A" for methods 2 and 3. Step was: Sat: _______ Unsat _______*

Denotes an entry required on the JPM cover sheet. **Denotes a Critical Step.

DOCCONTENT.dll PAGE 3 OF 5 R EV. 4A JPM TITLE: DETERMINE ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: LJACO-02R INSTRUCTOR WORKSHEET StepExpected Operator Actions

3. **Performs steps 33.d and e.

3.1 Reads

NOTE prior to step 37.d.

3.2 Informs

the Unit 1 SFM that the corrected ocean temperature is greater than the Tech Spec limit of 62F, and that temperatures need to be recorded every 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months . Initials step d.** Note: Unit 2 SFM does not need to be informed since Unit 2 is in a refueling outage (not in Modes 1

-4). 3.3 Checks "N/A" for step 37.e. Step was: Sat: _______ Unsat _______*

Stop Time: Total Time: (Enter total time on the cover page)*Denotes an entry required on the JPM cover sheet. **Denotes a Critical Step.

DOCCONTENT.dll PAGE 4 OF 5 R EV. 4A EXAMINEE CUE SHEET JPM NUMBER: LJACO-02R Initial Conditions:

Unit 1 is at 50% power with CWP 1-2 out of service for replacement of damaged screens. Unit 2 is in day 14 of a refueling outage. Current plant conditions for the Circ Water and ASW systems are as follows: Component Status Current Ocean Water Temperature CWP 1-1 In-service TI-311 61F CWP 1-2 Cleared TI-328 61F ASW Pp 1-1 In-service to CCW HX 1-1 TI-1484 61.5F ASW Pp 1-2 In-STBY TI-1485 60F CWP 2-1 Cleared TI-311 61F CWP 2-2 Cleared TI-328 61F ASW Pp 2-1 In-service to CCW HX 2-1 TI-1484 61.5F ASW Pp 2-2 Cleared TI-1485 61F Initiating Cue:

Shift Forman directs you to determine the Ultimate Heat Sink Temperature, using STP I-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 33.

DOCCONTENT.dll PAGE 5 OF 5 R EV. 4A N UCLEAR P OWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE M EASURE AUTHOR:L ISAT ORIBIOD ATE:06/20/2014OPERATIONSR EPRESENTATIVE

A BDULK ADIRD ATE:06/20/2014R EV.0 Number: NRCL121-A2 Title: DETERMINE DILUTION REQUIREMENTS TO RAISE POWER Examinee: Evaluator: Print Signature Date Testing Method: Perform X Simulate Results: Sat Unsat Total Time: minutes Comments:

References:

DCPP Unit 2 Cycle 18 Reactivity Briefing Sheet (263 to 310 EFPD) Alternate Path: Yes No X Time Critical: Yes No X Time Allotment: 10 minutes Critical Steps: 2.2, 3.3, 4.1, 5.1 Job Designation:

RO or SRO Rev Comments: modified from L081 NRC ADMRO1 Gen KA / Rating: G2.1.25 - Conduct of Operations 3.9 Note: This is an admin JPM (RO), intended for the classroom setting.

JPM TITLE: DETERMINE DILUTION REQUIREMENTS TO RAISE POWER JPM NUMBER: NRCL121-A2 EVALUATOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

Calculator, Reactivity Briefing Sheet from the Reactivity Handbook Initial Conditions Given: Unit 2 was ramped down due to high vibration on the main turbine.

Unit 2 has been at 80% power for 3 days.

Control Bank D is at 200 steps Initiating Cue:

The Shift Foreman directs you to determine the dilution or boration requirements to raise power to 90% assuming final rod position of 210 steps using the data from the Reactivity Briefing Sheet (from Reactivity Handbook)

DO NOT READ TASK STANDARD TO EXAMINEE Task Standard:

Determined that 928 (+/

- 5 ) gallons of primary water is required for the 10% power increase.

NRCL121-A2 PAGE 2 OF 5 R EV. 0 JPM TITLE: DETERMINE DILUTION REQUIREMENTS TO RAISE POWER JPM NUMBER: NRCL121-A2 EVALUATOR WORKSHEET Start Time:

Step Expected Operator Actions

1. Obtain the correct procedure.

1.1 **********************************

Cue: Provide examinee with reactivity briefing sheet, if not already done.

Sat: ______ Unsat _______

Comment: 2.0B** Calculate reactivity change for 10% change in power 2.1 From graph power coefficient is

-15.47 pcm/% power.

2.2 Record

e d (-)154.7 pcm for 10% increase in power.

- Sat: ______ Unsat _______

Comment: 3.1B** Calculate reactivity change due to change in rod position

3.1 Recorded

45.9 pcm for Control Bank D at 210 steps.

(From graph, A. Control Bank D Integral Rod Worth) 3.2 Recorded 9 8.1 pcm for Control Bank D at 2 00 steps.

(From graph, A. Control Bank D Integral Rod Worth) 3.3 Recorded (+)52.2 pcm for change in rod position.

- (98.1 - 45.9 ) Sat: ______ Unsat _______

Comment: NRCL121-A2 PAGE 3 OF 5 R EV. 0 JPM TITLE: DETERMINE DILUTION REQUIREMENTS TO RAISE POWER JPM NUMBER: NRCL121-A2 EVALUATOR WORKSHEET 4.2B** Calculate reactivity left after accounting change in rod position.

4.1 Recorded

(-)102.5 pcm

)reactivity from change in rods position on total reactivity from change in power.

- (-154.7 + 52.2) Sat: ______ Unsat _______

Comment: 5.3B** Determines amount of primary water to add Note: The examinee may set up a ratio to get the primary water needed, or may do two steps (determine power change needing dilution, and then dilution for that power change).

5.1 Determined

928 (+/- 5 ) gallons of primary water is required.

(102.5 pcm/15.47 pcm/% = 6.63 % pwr) (6.63% x 140 gal/% =

928 gallons (+/- 5 gallons) ** Note: The critical "part" of the above step is the dilution gallons, as the data can be manipulated several different ways in one or more steps to arrive at the right answer. Sat: ______ Unsat _______

Comment: Stop Time:

Total Time:

(Enter total time on the cover page)

Follow up Question Documentation

Question: ____________________________________________________________________

______________________________________________________________________________

Response: ___________________________________________________________________

______________________________________________________________________________

NRCL121-A2 PAGE 4 OF 5 R EV. 0 EXAMINEE CUE SHEET JPM NUMBER: NRCL121-A2 Initial Conditions:

Given: Unit 2 was ramped down due to high vibration on the main turbine.

Unit 2 has been at 80% power for 3 days.

Control Bank D is at 200 steps Initiating Cue: The Shift Foreman directs you to determine the dilution or boration requirements to raise power to 90% assuming final rod position of 210 steps using the data from the Reactivity Briefing Sheet (from Reactivity Handbook)

Answer (show work)

NRCL121-A2 PAGE 5 OF 5 R EV. 0

NUCLEAR POWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE MEASURE Number: NRCL081LJA_ROA1 Title: DETERMINE DILUTION REQUIREMENTS FOR A POWER INCREASE Examinee:

Evaluator:

Print Signature Date Results: Sat Unsat Total Time: minutes Comments:

References:

DCPP Unit 1 Cycle 16 Reactivity Briefing Sheet (9000 MWD/MTU) Alternate Path:

Yes No X Time Critical:

Yes No X Time Allotment:

15 Minutes Critical Steps:

2-6 Job Designation:

RO Task Number:

G2.1.25 Rating: 3.9 JOHN P. LYLE E D HURST AUTHOR: GARY HUTCHISON DATE: 12/10/09 R EV. 1 JPM TITLE: DETERMINE DILUTION REQUIREMENT S FOR A POWER INCREASE JPM NUMBER: NRCL081LJA_ROA1 INSTRUCTOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions, initiating cue, and task standard. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

Calculator, Reactivity Briefing Sheet Initial Conditions:

Unit 1 was ramped down due to problems with Govenor valve 4. Unit 1 has been at 90% power for 3 days with Control Bank D at 200 steps. Initiating Cue:

Shift Foreman directs you to determine the dilution or boration requirements to increase power to 95% assuming final rod position of 210 steps using the data from the Reactivity Briefing Sheet. Task Standard:

Operator determines that 230 (+/- 5 ) gallons of primary water is required. NRCL081LJA_ROA1 rev 1.doc PAGE 2 OF 6 R EV. 1 JPM TITLE: DETERMINE DILUTION REQUIREMENT S FOR A POWER INCREASE JPM NUMBER: NRCL081LJA_ROA1 INSTRUCTOR WORKSHEET Start Time: StepExpected Operator Actions

1. Operator obtains correct procedure

1.1 Operator

obtains Reactivity Briefing Sheet. Note: Provide exam copy of Reactivity Briefing Sheet Step was: Sat: _______ Unsat _______*

2. ** Calculates reactivity from change in power 2.1 Operator determines that power coefficient is -12.57 pcm/% power. **

2.2 Operator

determines PCM for 5% increase in power. (-62.85 pcm) ** Step was: Sat: _______ Unsat _______*

3. **Calculates reactivity from change in rod position

3.1 Operator

determines PCM for Control Bank D at 210 steps. (28 pcm) **

3.2 Operator

determines PCM for Control Bank D at 200 steps. (59.8 pcm) **

3.3 Operator

determines PCM for change in rod position. (PCM at 200 - PCM at 220 steps = 31.8 pcm ) ** Step was: Sat: _______ Unsat _______*

Denotes an entry required on the JPM cover sheet. **Denotes a Critical Step.

NRCL081LJA_ROA1 rev 1.doc PAGE 3 OF 6 R EV. 1 JPM TITLE: DETERMINE DILUTION REQUIREMENT S FOR A POWER INCREASE JPM NUMBER: NRCL081LJA_ROA1 INSTRUCTOR WORKSHEET StepExpected Operator Actions

4. ** Calculates reactivity left after accounting change in rod position.

4.1 Accounts

for reactivity from change in rods position on total reactivity from change in power. (-62.8 + 31.8 =

-31.05 pcm)** Step was: Sat: _______ Unsat _______*

5. **Determines % power change from reactivity associated with dilution.

5.1 Determines

that 2.47 % power change is left to dilution water. (-31.05 pcm/

-12.57 pcm/% power)** Step was: Sat: _______ Unsat _______*

6. **Determines amount of primay water to add. 6.1 Determines that 230 (+/- 5 ) gallons of primary water is required. (2.47%

93 gal/% = 230 gallons) ** Step was: Sat: _______ Unsat _______*

Stop Time: Total Time: (Enter total time on the cover page)*Denotes an entry required on the JPM cover sheet. **Denotes a Critical Step.

NRCL081LJA_ROA1 rev 1.doc PAGE 4 OF 6 R EV. 1 JPM TITLE: DETERMINE DILUTION REQUIREMENT S FOR A POWER INCREASE JPM NUMBER: NRCL081LJA_ROA1 ANSWER K EY Initial Conditions:

Unit 1 was ramped down due to problems with Govenor valve 4. Unit 1 has been at 90% power for 3 days with Control Bank D at 200 steps Initiating Cue:

Shift Foreman directs you to determine the dilution or boration requirements to increase power to 95% assuming final rod position of 210 steps using the data from the Reactivity Briefing Sheet.

Answer Key Operator determines that 230 (+/- 5 ) gallons of primary water is required.

NRCL081LJA_ROA1 rev 1.doc PAGE 5 OF 6 R EV. 1 EXAMINEE CUE SHEET JPM NUMBER: NRCL081LJA_ROA1 Initial Conditions:

Unit 1 was ramped down due to problems with Govenor valve 14 . Reactor power is now stabilized at approximately 90% with Control Bank D at 200 steps Initiating Cue:

Shift Foreman directs you to determine the dilution or boration requirements to increase power to 95% assuming final rod position of 210 steps using the data from the Reactivity Briefing Sheet.

NRCL081LJA_ROA1 rev 1.doc PAGE 6 OF 6 R EV. 1 NUCLEAR POWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE MEASURE Number: NRCL121-A 3 Title: PERFORM OUTAGE SAFETY CHECKLIST Examinee: Evaluator:

Print Signature Date Testing Method:

Perform X Simulate Results: Sat Unsat Total Time:

minutes Comments:

References:

AD8.DC55, Outage Safety Scheduling, Attachment 4, pg. 6, Rev. 38 Alternate Path:

Yes No X Time Critical:

Yes No X Time Allotment:

10 minutes Critical Steps:

2.1, 2.2, (3 or 4 & 5) 6, 7, 8 Job Designation:

RO Rev Comments:

Bank: LJAEC

-01R ; previously used in L061C NRC ADM02 Gen KA / Rating:

G 2.2.37 - Ability to determine operability and/or availability of safety related equipment 3.6 Note: This is an admin JPM (RO), intended for the classroom setting.

AUTHOR: LISA TORIBIO/ DATE: OPERATIONS REPRESENTATIVE

ABDUL KADIR/ DATE: R EV. 0 JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: NRCL121-A 3 EVALUATOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the

evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

AD8.DC55, Outage Safety Scheduling, Attachment 4, pg. 6, Rev. 38 Technical Specifications (available)

NRCL121-A 3 PAGE 2 OF 9 R EV. 0 JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: NRCL121-A 3 EVALUATOR WORKSHEET Initial Conditions Unit 1 is currently in MODE 6 with Core reload in progress.

Current plant parameters are as follows:

Operable Cleared Offsite power sources Startup power X Aux power X Onsite power sources Diesel Generator 1 X Diesel Generator 2 X Diesel Generator 3 X Vital bus crosstie 4kV & 480v Bus F X 4kV & 480v Bus G X 4kV & 480v Bus H X Onsite distribution sys.

4kV & 480v Bus F X 4kV & 480v Bus G X 4kV & 480v Bus H X Instrument AC Panels PY-11 X PY-11A X PY-12 X PY-13 X PY-13A X PY-14 X Vital DC Power DC Bus 1-1 X DC Bus 1-2 X DC Bus 1-3 X Refueling cavity level 23.4 Feet Initiating Cue:

The Shift Foreman directs you to perform the AD8.DC55, "Outage Safety Scheduling," Att 4, page 6, Mode 6 Outage Safety Checklist for the current plant conditions DO NOT READ TASK STANDARD TO EXAMINEE Task Standard:

Correctly completes AD8.DC55, Att 4, page 6, Mode 6 Outage Safety Checklist for VITAL AC POWER

. NRCL121-A 3 PAGE 3 OF 9 R EV. 0 JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: NRCL121-A 3 EVALUATOR WORKSHEET Start Time:

Step Expected Operator Actions

1. Obtain the correct procedure.

Note: Provide exam copy of AD8.DC55, Att 4, page 6 (page 9 of this JPM). **********************************

Sat: ______ Unsat _______

Comment: 2.0B** Determines status of power to operable vital buses

. 2.1 Determines S/U Power is operable and marks the appropriate "boxes" on Att 4, page 6. **

2.2 Determines

that a D/G is operable for 4kV vital bus F (D/G 1

-3) and G (D/G 1

-2) and marks the appropriate "boxes" on Att 4, page 6. **

Sat: ______ Unsat _______

Comment: 3.1B** Determines onsite power supply operability

. Note: Examinee may complete either step 3 (page 7) or both steps 4 and 5 (page 8 of this JPM).

3.1 Determines

that D/G 1

-2 and 1-3 are operable and marks the appropriate "boxes" on Att 4, page 6. **

Sat: ______ Unsat _______

Comment: NRCL121-A 3 PAGE 4 OF 9 R EV. 0 JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: NRCL121-A 3 EVALUATOR WORKSHEET Step Expected Operator Actions 4.2B** Determines status of refueling cavity

. 4.1 Determines that refueling cavity level is 23.4 feet ( 23 feet above the vessel flange) and the upper internals are removed (i.e., core onload is in progress) and marks the appropriate "boxes" on Att 4, page 6.

- 4.2 Determines that S/U power is operable and marks the appropriate "boxes" on Att 4, page 6. Sat: ______ Unsat _______

Comment: 5.3B** Determines Diesel Generator (D/G) Operability

5.1 Determines

that one D/G is operable (either D/G 1

-2 or 1-3) and marks appropriate "boxes" on Att 4, page 6.**

5.2 Determines

that a different D/G (either D/G 1-3 or 1-2) is either operable or available and marks appropriate "boxes" on Att 4, page 6. **

Sat: ______ Unsat _______

Comment: 6.4B** Determines TS required 4kV and 480V bus operability

6.1 Determines

that 4 kV buses F and G, as well as 480V buses F and G, are operable and marks appropriate "boxes" on Att 4, page 6. **

Sat: ______ Unsat _______

Comment: NRCL121-A 3 PAGE 5 OF 9 R EV. 0 JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: NRCL121-A 3 EVALUATOR WORKSHEET Step Expected Operator Actions 7.5B** Determines status of Instrument AC Power Panels. 7.1 Determines that all vital instrument AC power panels are operable and marks appropriate "boxes" on Att 4, page 6. **

Sat: ______ Unsat _______

Comment: 8.6B** Determines status of Vital DC Power

8.1 Determines

that all vital DC buses are operable and marks appropriate "boxes" on Att 4, page 6. **

Sat: ______ Unsat _______

Comment: Stop Time:

Total Time:

(Enter total time on the cover page)

Follow up Question Documentation

Question: ____________________________________________________________________

______________________________________________________________________________

Response: ____________________________________________________________________

______________________________________________________________________________

NRCL121-A 3 PAGE 6 OF 9 R EV. 0 JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: NRCL121-A 3 EVALUATOR WORKSHEET NRCL121-A 3 PAGE 7 OF 9 R EV. 0 JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: NRCL121-A 3 EVALUATOR WORKSHEET NRCL121-A 3 PAGE 8 OF 9 R EV. 0 E XAMINEE C UE S HEET JPM N UMBER: NRCL121-A3 NRCL121-A3 PAGE 9 OF 9 R EV. 0 Initial Conditions:

Unit 1 is currently in MODE 6 with Core reload in progress. Current plant parameters are as follows:

Operable Cleared Offsite power sources Startup power X Aux power X Onsite power sources Diesel Generator 1 X Diesel Generator 2 X Diesel Generator 3 X Vital bus crosstie 4kV & 480v Bus F X 4kV & 480v Bus G X 4kV & 480v Bus H X Onsite distribution sys. 4kV & 480v Bus F X 4kV & 480v Bus G X 4kV & 480v Bus H X Instrument AC Panels PY-11 X PY-11A X PY-12 X PY-13 X PY-13A X PY-14 X Vital DC Power DC Bus 1-1 X DC Bus 1-2 X DC Bus 1-3 X Refueling cavity level 23.4 Feet Initiating Cue: The Shift Foreman directs you to perform the AD8.DC55, "Outage Safety Scheduling," Att 4, page 6, Mode 6 Outage Safety Checklist for the current plant conditions

Unit 1 Outage Safety Checklist - Mode 6 RCS Level Greater Than or Equal to 111' AD8.DC55 R38 Page 35 of 66 Attachment 4: Page 6 of 7

AD8!DC55u3r38.DOC 1126.1027

)#2&3)

(!-4) 4)4))) 5#$/!&! ,678,7~# 9,678,7~# ,678,7~# :;;);;;);,~# ~# ~# !$!7~#

!7~# 3' "))#2&3

)$E0 (0-NUCLEAR POWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE MEASURE Number: LJ A EC-01R Title: PERFORM OUTAGE SAFETY CHECKLIST Examinee:

Evaluator:

Print Signature Date Testing Method:

Perform Simulate Results: Sat Unsat Total Time: minutes Comments: (Note: Any Unsat step requires a numbered comment; use back as needed.)

Page 7 contains a completed copy of AD8.DC55 Att 4, page 6 which is the examiner's key.

Page 8 contains an exam copy of AD8.DC55 Att 4, page 6 for the examinee to complete.

Rev 5A changes AD8.DC55 to current rev approved by ILT Supervisor.

References:

AD8.DC55, Outage Safety Scheduling, Attachment 7.4, Rev. 36 Alternate Path:

Yes No X Time Critical:

Yes No X Time Allotment

10 minutes Critical Steps:

2, 3, 6, 7 (or 2, 4, 5, 6, 7)

Job Designation:

RO Rev Comments/TIPs:

This JPM was rewritten; therefore, no revision bars were used. Incorporated TIP 19743-29. DCPP Task # / Rating: NA NA Gen KA # / Rating

G2.2.37 3.6 AUTHOR: D AVE RICHARDS / CHARLES HIBBARD DATE: 04/28/11 REVIEWED B Y: JOHN P. LYLE DATE: 04/28/11 TRAINING SUPERVISOR APPROVED B Y: ERIK WERNER DATE: 04/28/11 LINE MANAGER R EV. 5A JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: LJ A EC-01R INSTRUCTOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The examinee will be given the initial conditions and initiating cue. The task standard will NOT be read to the examinee.

The examiner will then ask if any clarifications are needed. If the task is being done in the plant or lab, and after identifying the appropriate procedure for the task, the examinee may be given the procedure and told what step to begin the task at. Required Materials:

Make a copy of Technical Specifications available for reference.

Initial Conditions:

Unit 1 is currently in Mode 6 with Core onload in progress. Current plant parameters are as follows:

Cleared Available Operable Offsite power sources Startup power X NA Aux power NA X Onsite power sources Diesel Generator 1 X Diesel Generator 2 X Diesel Generator 3 X Vital bus crosstie 4kV & 480v Bus F X NA 4kV & 480v Bus G X NA 4kV & 480v Bus H NA X Onsite distribution sys.

4kV & 480v Bus F X NA 4kV & 480v Bus G X NA 4kV & 480v Bus H NA X Instrument AC Panels PY-11 X NA PY-11A X NA PY-12 X NA PY-13 X NA PY-13A X NA PY-14 X NA Refueling cavity level 23.4 Feet Initiating Cue:

The Shift Foreman directs you to perform the AD8.DC55, "Outage Safety Scheduling," Att 4, page 6, Mode 6 Outage Safety Checklist for VITAL AC POWER ONLY, for the current plant conditions.

DOCCONTENT

.DLL PAGE 2 OF 9 R EV. 5A JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: LJ A EC-01R INSTRUCTOR WORKSHEET NOTE: Do NOT provide the student with the Task Standard.

Task Standard:

Correctly completes AD8.DC55, Att 4, page 6, Mode 6 Outage Safety Checklist for VITAL AC POWER.

Denotes an entry required on the JPM cover sheet. ** Denotes Critical Step and Sub Steps. DOCCONTENT

.DLL PAGE 3 OF 9 R EV. 5A JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: LJ A EC-01R INSTRUCTOR WORKSHEET Start Time:

Step Expected Operator Actions

1. Obtains the correct procedure. 1.1 Obtains AD8.DC55, Att 4, page 6, Mode 6 Outage Safety Checklist for VITAL AC POWER. Note: Provide exam copy of AD8.DC55, Att 4, page 6

, on page 8 of this JPM

. Step was: Sat: ______ Unsat _______*

[ ] Comment # (required for Unsat)

- 2. Determines status of power to operable vital buses.

2.1 Determines

S/U Power is operable and marks the appropriate "boxes" on Att 4, page 6.

- 2.2 Determines that a D/G is available for 4kV vital bus F (D/G 1

-3) and G (D/G 1-2) and marks the appropriate "boxes" on Att 4, page 6. ** Step was: Sat: ______ Unsat _______*

[ ] Comment # (required for Unsat)

Note: Examinee may complete either step 3 or both steps 4 and 5 (see logic in Att 4, page 6

). Note: Examiner's key on page 7 shows completion of steps 2, 3, 6, and 7.

- 3. Determines onsite power supply operability.

3.1 Determines

that D/G 1-2 and 1-3 are operable and marks the appropriate "boxes" on Att 4, page 6. ** Step was: Sat: ______ Unsat _______*

[ ] Comment # (required for Unsat)

Denotes an entry required on the JPM cover sheet. ** Denotes Critical Step and Sub Steps. DOCCONTENT

.DLL PAGE 4 OF 9 R EV. 5A JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: LJ A EC-01R INSTRUCTOR WORKSHEET Step Expected Operator Actions

- 4. Determines status of refueling cavity. Note: Examinee may complete either step 4.1 or step 4.2 (see logic in Att 4, pag e 6). 4.1 Determines that refueling cavity level is 23.4 feet ( 23 feet above the vessel flange) and the upper internals are removed (i.e., core onload is in progress) and marks the appropriate "boxes" on Att 4, page 6. ** 4.2 Determines that S/U power is operable and marks the appropriate "boxes" on Att 4, page 6. ** Step was: Sat: ______ Unsat _______*

[ ] Comment # (required for Unsat)

- 5. Determines D/G operability. 5.1 Determines that one D/G is operable (either D/G 1-2 or 1-3) and marks appropriate "boxes" on Att 4, page 6.

5.2 Determines

that a different D/G (either D/G 1-3 or 1-2) is either operable or available and marks appropriate "boxes" on Att 4, page 6. Step was: Sat: ______ Unsat _______*

[ ] Comment # (required for Unsat)

Denotes an entry required on the JPM cover sheet. ** Denotes Critical Step and Sub Steps. DOCCONTENT

.DLL PAGE 5 OF 9 R EV. 5A JPM TITLE: PERFORM OUTAGE SAFETY CHECKLIST JPM NUMBER: LJ A EC-01R INSTRUCTOR WORKSHEET Step Expected Operator Actions

- 6. Determines TS required 4kV and 480V bus operability.

6.1 Determines

that 4 kV buses F and G, as well as 480V buses F and G, are operable and marks appropriate "boxes" on Att 4, page 6. ** Step was: Sat: ______ Unsat _______*

[ ] Comment # (required for Unsat)

Note: The boxes at the bottom of the right hand column of Att 4, page 6 are a continuation of the boxes at the bottom of the left hand column.

Note: Tech Spec 3.8.2 says that only one of these vital buses is required to be operable in Mode 6.

Note: If requested, provide access to Tech Specs. ** 7. Determines status of Instrument AC Power Panels. 7.1 Determines that all vital instrument AC power panels are operable and marks appropriate "boxes" on Att 4, page 6. ** Step was: Sat: ______ Unsat _______*

[ ] Comment # (required for Unsat)

Stop Time:

Total Time:

(Enter total time on the cover page)

Denotes an entry required on the JPM cover sheet. ** Denotes Critical Step and Sub Steps. DOCCONTENT

.DLL PAGE 6 OF 9 R EV. 5A KEY (Steps 2, 3, 6, and 7) x x x x x x x x x x x x x x x x x x DOCCONTENT

.DLL PAGE 7 OF 9 R EV. 5A DOCCONTENT

.DLL PAGE 8 OF 9 R EV. 5A JPM NUMBER: LJ A EC-01R EXAMINEE CUE SHEET Initial Conditions:

Unit 1 is currently in Mode 6 with Core onload in progress. Current plant parameters are as follows:

Cleared Available Operable Offsite power sources Startup power X NA Aux power NA X Onsite power sources Diesel Generator 1 X Diesel Generator 2 X Diesel Generator 3 X Vital bus crosstie 4kV & 480v Bus F X NA 4kV & 480v Bus G X NA 4kV & 480v Bus H NA X Onsite distribution sys.

4kV & 480v Bus F X NA 4kV & 480v Bus G X NA 4kV & 480v Bus H NA X Instrument AC Panels PY-11 X NA PY-11A X NA PY-12 X NA PY-13 X NA PY-13A X NA PY-14 X NA Refueling cavity level 23.4 Feet Initiating Cue:

The Shift Foreman directs you to perform the AD8.DC55, "Outage Safety Scheduling," Att 4, page 6, Mode 6 Outage Safety Checklist for VITAL AC POWER ONLY, for the current plant conditions.

DOCCONTENT

.DLL PAGE 9 OF 9 R EV. 5A N UCLEAR P OWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE M EASURE AUTHOR:L ISAT ORIBIO/D ATE:OPERATIONSR EPRESENTATIVE

A BDULK ADIR/D ATE:R EV.0 Number: NRCL121-A4 Title: REVIEW LIQUID RADWASTE DISCHARGE CHECKLIST Examinee: Evaluator: Print Signature Date Testing Method: Perform X Simulate Results: Sat Unsat Total Time: minutes Comments:

References:

OP G-1:II, Liquid Radwaste System - Discharge of Liquid Radwaste, Rev. 37A CAP A-5, Liquid Radwaste Discharge Management, Rev. 48 Alternate Path: Yes No X Time Critical: Yes No X Time Allotment: 10 minutes Critical Step(s):

6 Job Designation: RO Rev Comments: modified from L061C NRC ADM04 Gen KA / Rating: 2.3.11 Ability to control radiation releases 3.8

Note: This is an admin JPM (RO), intended for the classroom setting.

JPM TITLE: REVIEW LIQUID RADWASTE DISCHARGE CHECKLI ST JPM NUMBER: NRCL121-A 4 EVALUATOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

OP G-1:II, Liquid Radwaste System

- Discharge of Liquid Radwaste, Rev.37A Partially completed Section 12 CAP A-5 Completed Attachment 11.1 Parts 1 & 2 Initial Conditions Chemistry has issued a discharge permit for PWR 0

-2 using CAP A

-5 Att. 11.1 parts 1 & 2. OP G

-1:II Section 12 has been partially completed. CCW HX 1

-1 is in service, and both Units are at 100% power Initiating Cue:

Review OP G

-1:II Section 12 Discharge Checklists for accuracy and completeness thru step 12.10. Document any discrepancies noted DO NOT READ TASK STANDARD TO EXAMINEE Task Standard:

1 Technical error identified

Section 12 page 2 (of 8), CCW HX 1

-1 is designated to be used for the release (initial condition), but alignment has been performed for CCW HX 1-2 (SW-1-6 8 is open when SW 6 7 should be open

) NRCL121-A 4 PAGE 2 OF 5 R EV. 0 JPM TITLE: REVIEW LIQUID RADWASTE DISCHARGE CHECKLI ST JPM NUMBER: NRCL121-A 4 EVALUATOR WORKSHEET Start Time:

Step Expected Operator Actions

1. Review step 12.1

- Parts 1 and 2 of discharge permit complete and signed by Chemistry 1.1 Review e d Parts 1 and 2 of CAP A

-5, Attachment 11.1 and determine d parts 1 & 2 are complete and signed by Chemistry Sat: ______ Unsat _______

Comment: 2. Review step 12.2 - Appropriate tank identifie d 2.1 Identifie d that PWR 0

-2 has been correctly circled for discharge Sat: ______ Unsat _______

Comment:

3. Review steps 12.3 (RE-18 adjustment)

& 12.4 (FIT-243 not operable actions)

3.1 Identifie

d that RE-18 setpoint doesn't require adjustment

3.2 Identified

FIT

-243 is OPERABLE Sat: ______ Unsat _______

Comment: 4. Review step 12.5 - Discharge flowpath aligned to inservice U1 CCW heat exchanger identifie d 4.1 Identified that LWS 436 to U1 CCW , marked as OPEN 4.2 Identified that LWS 43 9 to U 2 CCW , marked as CLOSED Sat: ______ Unsat _______

Comment: NRCL121-A 4 PAGE 3 OF 5 R EV. 0 JPM TITLE: REVIEW LIQUID RADWASTE DISCHARGE CHECKLI ST JPM NUMBER: NRCL121-A 4 EVALUATOR WORKSHEET Step Expected Operator Actions

5. Review steps 12.6 thru 12.9

- valves closed 5.1 Identified that steps 12.6 through 12.9 signed as completed Sat: ______ Unsat _______

Comment: 6.** Review step 12.10

- ASW checklist 6.1 Identified CCW HX 11 should be circled to be used, but that valve alignment was incorrectly done for CCW HX 12. **

Sat: ______ Unsat _______

Comment: Stop Time:

Total Time:

(Enter total time on the cover page)

Follow up Question Documentation

Question: ____________________________________________________________________

______________________________________________________________________________

Response: ____________________________________________________________________

______________________________________________________________________________

NRCL121-A 4 PAGE 4 OF 5 R EV. 0 EXAMINEE CUE SHEET JPM NUMBER: NRCL121-A 4 Initial Conditions:

Chemistry has issued a discharge permit for PWR 0

-2 using CAP A

-5 Att. 11.1 parts 1 & 2. OP G

-1:II Section 12 has been partially completed. CCW HX 1

-1 is in service, and both Units are at 100% power Initiating Cue: Review OP G

-1:II Section 12 Discharge Checklists for accuracy and completeness thru step 12.10. Document any discrepancies noted NRCL121-A 4 PAGE 5 OF 5 R EV. 0

NUCLEAR POWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE MEASURE Number: NRCADM061C-A4 Title: Review Liquid Radwaste Discharge Checklist.

Examinee:

Evaluator:

Print Signature Date Results: Sat Unsat Total Time: minutes Comments: Designed for SRO Candidates in a classroom settin

g.

References:

OP G-1: II , Liquid Radwaste System - Discharge of Liquid Radwaste, Rev. 35A CAP A-5, Liquid Radwaste Discharge Management, Rev. 41A Alternate Path:

Yes X No Time Critical:

Yes No X Time Allotment:

20 minutes Critical Steps: 4 Job Designation:

S RO K/A: G 2.3.6; Ability to approve release permits.

Rating: 3.8 AUTHOR: GARY HUTCHISON DATE: 08/12/2008 R EV. 1 JPM TITLE: REVIEW LIQUID RADWASTE DISCHARGE CHECKLIST JPM NUMBER: NRCADM 061C-A4 INSTRUCTOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. After identifying the appropriate procedure for the task, the examinee may be given the procedure and told the step with which to begin. Required Materials:

OP G-1:II, Liquid Radwaste System - Discharge of Liquid Radwaste, Rev. 35A Completed Attachments 9.1 & 9.5 CAP A-5 Completed Attachment 11.1 Parts 1 & 2. Initial Conditions:

Chemistry has issued a discharge permit for PWR 0-1 using CAP A-5 Att. 11.1 parts 1 & 2. OP G-1:II Attachments 9.1 & 9.5 have been completed. Initiating Cue:

As the Unit 1 Shift Foreman, review OP G-1:II Attachments 9.1 & 9.5 Discharge Checklists for accuracy and completeness. Document any discrepancies noted and determine if the discharge checklist should be approved or not approved based on your review. Task Standard:

2 Technical errors were identified:

Attachment 9.1 page 2, CCW HX 1-2 is circled to be used for the release, but SW-1-67 is opened when SW-1-68 should be opened PWR 0-2 has been aligned for discharge instead of PWR 0-1 Discharge authorization was not approved. NRCADM061C

-A4.DOC Page 2 of 6 R EV. 1 JPM TITLE: REVIEW LIQUID RADWASTE DISCHARGE CHECKLIST JPM NUMBER: NRCADM 061C-A4 INSTRUCTOR WORKSHEET Start Time:

Step Expected Operator Actions

1. Review checks on page 1 of Attachment 9.1.

1.1 Determines

Batch number matches CAP A-5 Att. 11.1 number.

1.2 Identifies

that Valve alignment is complete. 1.3 Identifies that independent verification of Valve alignment is complete.

1.4 Identifies

that dilution flowrate is adequate.

1.5 Identifies

that RE-18 setpoint doesn't require adjustment.

Step was: Sat: ______ Unsat _______*

- 2. Review Manual Valve Lineup Verification on page 2 of .1

2.1 Determines

that CCW HX 12 is to be circled to be used, but that valve alignment is for CCW HX 11.

Step was: Sat: ______ Unsat _______*

- 3. Review Attachment 9.5 PWR alignment checklist. 3.1 Determines that PWR 0-2 has been aligned for discharge instead of PWR 0-1. Step was: Sat: ______ Unsat _______*

- 4. Determine if Authorization should be approved.

4.1 Determines

that the Authorization should not be approved, based on either condition not meeting the procedural requirements.

Step was: Sat: ______ Unsat _______*

Denotes an entry required on the JPM cover sheet. ** Denotes a Critical Step.

NRCADM061C

-A4.DOC Page 3 of 6 R EV. 1 JPM TITLE: REVIEW LIQUID RADWASTE DISCHARGE CHECKLIST JPM NUMBER: NRCADM 061C-A4 INSTRUCTOR WORKSHEET Stop Time:

Total Time:

(Enter total time on the cover page)

Denotes an entry required on the JPM cover sheet. ** Denotes a Critical Step.

NRCADM061C

-A4.DOC Page 4 of 6 R EV. 1 JPM NUMBER: NRCADM 061C-A4 EXAMINEE CUE SHEET Initial Conditions:

Chemistry has issued a discharge permit for PWR 0-1 using CAP A-5 Att. 11.1 parts 1 & 2. OP G-1:II Attachments 9.1 & 9.5 have been completed. Initiating Cue:

As the Unit 1 Shift Foreman, review OP G-1:II Attachments 9.1 & 9.5 Discharge Checklists for accuracy and completeness. Document any discrepancies noted and determine if the discharge checklist should be approved or not approved based on your review.

Technical Errors Identified:

[ ] APPROVE Discharge [ ] DO NOT Approve Discharge

NRCADM061C

-A4.DOC Page 5 of 6 R EV. 1 REVIEW LIQUID RADWASTE DISCHARGE CHECKLIST JPM NUMBER: NRCADM 061C-A4 ATTACHMENT 1, SIMULATOR SETUP The simulator is not needed for the performance of this JPM.

NRCADM061C

-A4.DOC Page 6 of 6 R EV. 1 JPM TITLE: REVIEW LIQUID RADWASTE DISCHARGE CHECKLIST. JPM NUMBER: NRCADM 061C-A4 ANSWER K EY Initial Conditions:

Chemistry has issued a discharge permit for PWR 0-1 using CAP A-5 Att. 11.1 parts 1 & 2. OP G-1:II Attachments 9.1 & 9.5 have been completed. Initiating Cue:

As the Unit 1 Shift Foreman, review OP G-1:II Attachments 9.1 & 9.5 Discharge Checklists for accuracy and completeness. Document any discrepancies noted and determine if the discharge checklist should be approved or not approved based on your review.

Technical Errors Identified:

Attachment 9.1 page 2, CCW HX 1-2 is circled to be used for the release, but SW-1-67 is opened when SW-1-68 should be opened.

Attachment 9.5 has PWR 0-2 aligned when PWR 0-1 should be.

[ ] APPROVE Discharge [ X ] DO NOT Approve Discharge NRCADM061C

-A4.DOC Page 7 of 6 R EV. 1 NUCLEAR POWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE MEASURE Number: NRCL121-A5 Title: VERIFY A DETERMINATION OF ULTIMATE HEAT SINK TEMPERATURE Examinee: Evaluator:

Print Signature Date Testing Method:

Perform X Simulate Results: Sat Unsat Total Time:

minutes Comments:

References:

STP I-1A, Routine Shift Checks Required by Licenses, Attachment 12.1, Rev. 126 Technical Specifications, DCPP Units 1 & 2 Alternate Path:

Yes X No Time Critical:

Yes No X Time Allotment:

10 minutes Critical Steps:

2.3, 3.1, 4.1 Job Designation:

SRO Rev Comments:

modified from LJACO-02S Gen KA / Rating:

G2.1.2 5 - Conduct of Operations 3.9 Note: This is an admin JPM (SRO), intended for the classroom setting.

AUTHOR: LISA TORIBIO/ DATE: OPERATIONS REPRESENTATIVE

ABDUL KADIR/ DATE: R EV. 0 JPM TITLE: VERIFY A DETERMINATION OF ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: NRCL121-A5 EVALUATOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

Completed copy of STP I

-1A, Attachment 12.1, MODE 1 Shift Checklist, Step 37 (SR 3.7.9.2).

LCO 3.7.9 Initial Conditions GIVEN: Unit 1 is at 50% power CWP 1-2 out of service for replacement of damaged screens Unit 2 is in day 14 of a refueling outage.

Current plant conditions for the Circ Water and ASW systems are as follows: Component Status Current Ocean Temperature CWP 1-1 In-service TI-311 Out of Calibration CWP 1-2 Cleared TI-328 6 1.1 F ASW Pp 1-1 In-service to CCW HX 1

-1 TI-1484 59.5 F ASW Pp 1-2 In-STBY TI-1485 61.4 F CWP 2-1 Cleared TI-311 60.3 F CWP 2-2 Cleared TI-328 60.4 F ASW Pp 2-1 In-service to CCW HX 2

-1 TI-1484 59.5 F ASW Pp 2-2 Cleared TI-1485 60.4 F Initiating Cue:

Unit 1 BOPCO has just completed STP I

-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 37.

BOPCO has just informed you that the Ultimate Heat Sink Temperature requires 12 hour1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months recordings for the given conditions.

Review the completed STP data sheet and determine if the unit is in a LCO ACTION statement for Ultimate Heat Sink and what frequency of ocean temperature monitoring is required. DO NOT READ TASK STANDARD TO EXAMINEE Task Standard:

STP I-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, is reviewed and it is determined the calculation of Ultimate Heat Sink temperature was incorrect. The correct temperature is above the limit for increased monitoring (12 hours1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months ), but the LCO is satisfied, (temperature is less than 64°F) NRCL121-A5 PAGE 2 OF 5 R EV. 0 JPM TITLE: VERIFY A DETERMINATION OF ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: NRCL121-A5 EVALUATOR WORKSHEET Start Time:

Step Expected Operator Actions 1.** Review Step 37, Method 1 Data

. 1.1 Read NOTE prior to step 37.a

1.2 Method

1 incorrectly used. CWP 1

-2 is not running (Per note, temperature indicator not available) and TI-311 is out of calibration.**

Sat: ______ Unsat _______

Comment: 2. Perform Step 37, Method 2 2.1 NOTE: The sheet may not be completed as the key is however, some manner must be used to determine the correct ocean temperature Used method 2 to determine ocean temperature

TI-1484 = 59.5°F TI-148 5. = N/A 2.2 Added 0.7°F for instrument error correction

2.3 Determined

ocean temperature to be between 60 and 62

°F (60.2°F) Sat: ______ Unsat _______ Comment: 3.** Determine ocean temperature monitoring required 3.1 Required ocean temperature monitoring is 37.d (12 hours1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months ) **

Sat: ______ Unsat _______

Comment: 4.** Evaluates LCO 3.7.9 (UHS) ** 4.1 LCO is met, UHS is OPERABLE (less than 6 4°F)** Sat: ______ Unsat _______

Comment: NRCL121-A5 PAGE 3 OF 5 R EV. 0 JPM TITLE: VERIFY A DETERMINATION OF ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: NRCL121-A5 EVALUATOR WORKSHEET KEY Is the unit in an ACTION statement for Ultimate Heat Sink? Yes / No. (From 3.7.9 bases: The UHS is required to be OPERABLE and is considered OPERABLE if it is at or below the maximum temperature that would allow the ASW to operate for at least 30 days following the DBA without exceeding the maximum design temperature of the CCW system. To meet this condition, the UHS temperature should not exceed 64°F unless two CCW heat exchangers are in service during normal unit operation. With two heat exchangers in service, operation with elevated UHS temperatures as high as 70°F is acceptable.

) What is the frequency of ocean temperature monitoring required?

12 hours1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months Stop Time:

Total Time:

(Enter total time on the cover page)

Follow up Question Documentation

Question: ____________________________________________________________________

______________________________________________________________________________

Response: ____________________________________________________________________

______________________________________________________________________________

NRCL121-A5 PAGE 4 OF 5 R EV. 0 69-20232 01/27/14 Page 15 of 26 STP I-1A (UNIT 1) ATTACHMENT 12.1 TITLE: MODE 1 Shift Checklist STP_I-1Au1r27.DOC 06 0515.1508 APPL MODE TECH SPEC

REFERENCE A. CHECK / VERIFICATION FROM CONTROL ROOM PERF 37.Determine the Ultimate Heat Sink (UHS) temperature using one of the following methods:NOTE: Temperature indicators are only available whentheir associated pumps are running.

a.Method 1 - Record Pacific Ocean water temp as readon the following indicators:N/A [ ] ______ TI-311 (T2400A) (CWP 1-1) _______FN/A [ ] TI-328 (T2401A) (CWP 1-2) _______FN/A [ ] Record the highest of the available indicators. F Instrument Error Correction 1.9 F Add the highest available indicator reading and the Instrument Error Correction. F b.Method 2 - Record Pacific Ocean water temp on thefollowing indicators:N/A [ ] ______ N/A [ ] TI-1484 (ASWP 1-1) ___FTI-1485 (ASWP 1-2) _______FN/A [ ] Record the highest of the available indicators. F Instrument Error Correction 0.7 F Add the highest available indicator reading and the Instrument Error Correction.°F 1 SR 3.7.9.2 69-20232 01/27/14 Page 16 of 26 STP I-1A (UNIT 1) ATTACHMENT 12.1 TITLE: MODE 1 Shift Checklist STP_I-1Au1r27.DOC 06 0515.1508 APPL MODE TECH SPEC

REFERENCE A. CHECK / VERIFICATION FROM CONTROL ROOM PERF c.Method 3 - If Method 1 and Method 2 are notavailable, M&TE may be used.N/A [ ] ______ Instrument Used: ____________________Cal Due Date: ____________________Reading using M&TE F Uncertainty of M&TE F Add M&TE ocean temp and uncertainty F NOTE: Tech Spec Bases B3.7.9 specifies that the UHS is common to both units. Therefore any required action due to elevated ocean water temp would apply to both units depending on mode requirements. Notify the Unit 2 SFM as required.

d.IF corrected ocean temp is > [60F] AND [62F],THEN perform the following:N/A [ ] 1)Notify SFM to review Tech Spec SR 3.7.9.2.______ 2)Record ocean temp every 12 hours1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months .

______ e.IF corrected ocean temp is > [62F] AND [64F],THEN perform the following:N/A [ ] 1)Notify SFM to review Tech Spec SR 3.7.9.2.______ 2)Record ocean temp every 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months .

______ f.IF corrected ocean temp is > [64F],THEN place both CCW HXs in service:N/A [ ] ______ SR 3.7.9.2 (Continued) 1 EXAMINEE CUE SHEET JPM NUMBER: NRCL121-A5 Initial Conditions:

GIVEN: Unit 1 is at 50% power CWP 1-2 out of service for replacement of damaged screens Unit 2 is in day 14 of a refueling outage.

Current plant conditions for the Circ Water and ASW systems are as follows: Component Status Current Ocean Temperature CWP 1-1 In-service TI-311 Out of Calibration CWP 1-2 Cleared TI-328 6 1.1 F ASW Pp 1-1 In-service to CCW HX 1

-1 TI-1484 59.5 F ASW Pp 1-2 In-STBY TI-1485 61.4 F CWP 2-1 Cleared TI-311 60.3 F CWP 2-2 Cleared TI-328 60.4 F ASW Pp 2-1 In-service to CCW HX 2

-1 TI-1484 59.5 F ASW Pp 2-2 Cleared TI-1485 60.4 F Initiating Cue:

Unit 1 BOPCO has just completed STP I

-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 37.

BOPCO has just informed you that the Ultimate Heat Sink Temperature requires 12 hour1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months recordings for the given conditions.

Review the completed STP data sheet and determine if the unit is in a LCO ACTION statement for Ultimate Heat Sink and what frequency of ocean temperature monitoring is required. Is the unit in an ACTION statement for Ultimate Heat Sink? Yes /

No. What is the frequency of ocean temperature monitoring required?

24 hours2.777778e-4 days 0.00667 hours 3.968254e-5 weeks 9.132e-6 months 12 hours1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months NRCL121-A5 PAGE 5 OF 5 R EV. 0 69-20232 01/27/14 Page 15 of 26 STP I-1A (UNIT 1) ATTACHMENT 12.1 TITLE: MODE 1 Shift Checklist STP_I-1Au1r27.DOC 06 0515.1508 APPL MODE TECH SPEC

REFERENCE A. CHECK / VERIFICATION FROM CONTROL ROOM PERF 37.Determine the Ultimate Heat Sink (UHS) temperature using one of the following methods:NOTE: Temperature indicators are only available whentheir associated pumps are running.

a.Method 1 - Record Pacific Ocean water temp as readon the following indicators:N/A [ ] ______ TI-311 (T2400A) (CWP 1-1) _______FN/A [ ] TI-328 (T2401A) (CWP 1-2) _______FN/A [ ] Record the highest of the available indicators. F Instrument Error Correction 1.9 F Add the highest available indicator reading and the Instrument Error Correction. F b.Method 2 - Record Pacific Ocean water temp on thefollowing indicators:N/A [ ] ______ TI-1484 (ASWP 1-1) _______FN/A [ ] TI-1485 (ASWP 1-2) _______FN/A [ ] Record the highest of the available indicators. F Instrument Error Correction 0.7 F Add the highest available indicator reading and the Instrument Error Correction.

°F 1 SR 3.7.9.2

69-20232 01/27/14 Page 16 of 26 STP I-1A (UNIT 1) ATTACHMENT 12.1 TITLE: MODE 1 Shift Checklist STP_I-1Au1r27.DOC 06 0515.1508 APPL MODE TECH SPEC

REFERENCE A. CHECK / VERIFICATION FROM CONTROL ROOM PERF c.Method 3 - If Method 1 and Method 2 are notavailable, M&TE may be used.N/A [ ] ______ Instrument Used: ____________________Cal Due Date: ____________________Reading using M&TE F Uncertainty of M&TE F Add M&TE ocean temp and uncertainty F NOTE: Tech Spec Bases B3.7.9 specifies that the UHS is common to both units. Therefore any required action due to elevated ocean water temp would apply to both units depending on mode requirements. Notify the Unit 2 SFM as required.

d.IF corrected ocean temp is > [60F] AND [62F],THEN perform the following:N/A [ ] 1)Notify SFM to review Tech Spec SR 3.7.9.2.______ 2)Record ocean temp every 12 hours1.388889e-4 days 0.00333 hours 1.984127e-5 weeks 4.566e-6 months .

______ e.IF corrected ocean temp is > [62F] AND [64F],THEN perform the following:N/A [ ] 1)Notify SFM to review Tech Spec SR 3.7.9.2.______ 2)Record ocean temp every 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months .

______ f.IF corrected ocean temp is > [64F],THEN place both CCW HXs in service:N/A [ ] ______ SR 3.7.9.2 (Continued) 1 NUCLEAR POWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE MEASURE Number: LJACO-02S Title: VERIFY A DETERMINATION OF ULTIMATE HEAT SINK TEMPERATURE Examinee:

Evaluator:

Print Signature Date Results: Sat Unsat Total Time: minutes Comments: This JPM requires that STP I-1A, Attachment 12.1, Step 37 be filled out ahead of time. The required data is included in an attachment to this JPM. Rev 4A changes to current rev of I-1A approved by ILT supervisor

References:

STP I-1A, Routine Shift Checks Required by Licenses, Attachment 12.1, Rev. 121 Technical Specifications, DCPP Units 1 & 2 Alternate Path:

Yes X No Time Critical:

Yes No X Time Allotment:

10 Minutes Critical Steps:

2, 4 Job Designation: SRO Task Number:

G2.1.23 Rating: 4.4 AUTHOR: DAVID RICHARDS / CHARLES HIBBARD DATE: 05/04/11 REVIEWED B Y: JOHN P. LYLE DATE: 05/04/11 TRAINING SUPERVISOR APPROVED B Y: KEN JOHNSTON DATE: 05/05/11 MANAGER - OPERATIONS R EV. 4A JPM TITLE: VERIFY A DETERMINATION OF ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: LJACO-02S INSTRUCTOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

Completed copy of STP I-1A, Attachment 12.1, MODE 1 Shift Checklist, Step 37 (SR 3.7.9.2) Initial Conditions:

Unit 1 is at 50% power with CWP 1-2 out of service for replacement of damaged screens. Unit 2 is in day 14 of a refueling outage. Current plant conditions for the Circ Water and ASW systems are as follows: Component Status Current Ocean Water Temperature CWP 1-1 In-service TI-311 61F CWP 1-2 Cleared TI-328 61F ASW Pp 1-1 In-service to CCW HX 1-1 TI-1484 61.5F ASW Pp 1-2 In-STBY TI-1485 60F CWP 2-1 Cleared TI-311 61F CWP 2-2 Cleared TI-328 61F ASW Pp 2-1 In-service to CCW HX 2-1 TI-1484 62F ASW Pp 2-2 Cleared TI-1485 61F Initiating Cue:

Unit 1 BOPCO has just completed STP I-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 37.

BOPCO has determined that the Ultimate Heat Sink Temperature is satisfactory for the given conditions. Review the completed STP data sheet and determine if his assessment is correct and implement any actions needed based on your review.

DO NOT READ TASK STANDARD TO EXAMINEE Task Standard:

STP I-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 33 reviewed for completeness and any actions implemented based on your review. DOCCONTENT.dll PAGE 2 OF 6 R EV. 4A JPM TITLE: VERIFY A DETERMINATION OF ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: LJACO-02S INSTRUCTOR WORKSHEET Start Time: StepExpected Operator Actions

1. Obtains correct procedure

1.1 Obtains

completed STP I-1A, Attachment 12.1, Step 37. Note: Provide completed exam copy of STP I-1A, Attachment 12.1, Step

37. Step was: Sat: _______ Unsat _______*

2. **Verifies UHS temperature method 1.

2.1 Reads

NOTE prior to step 37.a. 2.2 Verifies that the Pacific Ocean water temperature of 61F is entered for TI-311.** 2.3 Verifies that the TI-328 entry (CWP 1-2) is checked "N/A", because the pump is not running (per Note). 2.4 Verifies that 61F is entered as the highest temperature

.** 2.5 Notes that the instrument error was added incorrectly.** Note: The value entered on the completed STP I-1A was 61.9 F. The correct value is 62.9 F. Step was: Sat: _______ Unsat _______*

Denotes an entry required on the JPM cover sheet. **Denotes a Critical Step.

DOCCONTENT.dll PAGE 3 OF 6 R EV. 4A JPM TITLE: VERIFY A DETERMINATION OF ULTIMATE HEAT SINK TEMPERATURE JPM NUMBER: LJACO-02S INSTRUCTOR WORKSHEET StepExpected Operator Actions

3. Verifies UHS temperature using methods 2

& 3. 3.1 Verifies that "N/A" is checked for Method 2.

3.2 Verifies

that "N/A" is checked for Method 3. Step was: Sat: _______ Unsat _______*

4. **Verifies appropriate Tech Spec actions are taken. 4.1 Determines that step 37.d was completed incorrectly

.** Note: The step on the completed STP I

-1A was marked "N/A." Step d should have been initialed and the Unit 1 SFM informed of the actions in the step.

4.2 Notes

that Unit 1 needs to record UHS temperatures every 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months in the Operations Shift Log.** Note: Unit 2 SFM does not need to be informed since Unit 2 is in a refueling outage (not in Modes 1- 4). 4.3 Verifies step 37.e is checked "N/A." Step was: Sat: _______ Unsat _______*

Stop Time: Total Time: (Enter total time on the cover page)*Denotes an entry required on the JPM cover sheet. **Denotes a Critical Step.

DOCCONTENT.dll PAGE 4 OF 6 R EV. 4A EXAMINEE CUE SHEET JPM NUMBER: LJACO-02S Initial Conditions:

Unit 1 is at 50% power with CWP 1

-2 out of service for replacement of damaged screens. Unit 2 is in day 14 of a refueling outage. Current plant conditions for the Circ Water and ASW systems are as follows: Component Status Current Ocean Water Temperature CWP 1-1 In-service TI-311 61F CWP 1-2 Cleared TI-328 61F ASW Pp 1-1 In-service to CCW HX 1-1 TI-1484 61.5F ASW Pp 1-2 In-STBY TI-1485 60F CWP 2-1 Cleared TI-311 61F CWP 2-2 Cleared TI-328 61F ASW Pp 2-1 In-service to CCW HX 2-1 TI-1484 62F ASW Pp 2-2 Cleared TI-1485 61F Initiating Cue:

Unit 1 BOPCO has just completed STP I-1A, "Routine Shift Checks Required by Licenses," Attachment 12.1, Step 37.

BOPCO has determined that the Ultimate Heat Sink Temperature is satisfactory for the given conditions. Review the completed STP data sheet and determine if his assessment is correct and implement any actions needed based on your review. DOCCONTENT.dll PAGE 5 OF 6 R EV. 4A N UCLEAR P OWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE M EASURE AUTHOR:L ISAT ORIBIOD ATE:06/20/2014OPERATIONSR EPRESENTATIVE

A BDULK ADIRD ATE:06/20/2014R EV.0 Number: NRCL121-A6 Title: DETERMINE DILUTION REQUIREMENTS TO RAISE POWER Examinee: Evaluator: Print Signature Date Testing Method: Perform X Simulate Results: Sat Unsat Total Time: minutes Comments:

References:

DCPP Unit 2 Cycle 18 Reactivity Briefing Sheet (263 to 310 EFPD) Alternate Path: Yes No X Time Critical: Yes No X Time Allotment: 10 minutes Critical Steps: 2.2, 3.3, 4.1, 5.1 Job Designation:

RO or SRO Rev Comments: modified from L081 NRC ADMRO1 Gen KA / Rating: G2.1.25 - Conduct of Operations 3.9 Note: This is an admin JPM (RO), intended for the classroom setting.

JPM TITLE: DETERMINE DILUTION REQUIREMENTS TO RAISE POWER JPM NUMBER: NRCL121-A6 EVALUATOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions and initiating cue. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

Calculator, Reactivity Briefing Sheet from the Reactivity Handbook Initial Conditions Given: Unit 2 was ramped down due to high vibration on the main turbine.

Unit 2 has been at 80% power for 3 days.

Control Bank D is at 200 steps Initiating Cue:

The Shift Foreman directs you to determine the dilution or boration requirements to raise power to 90% assuming final rod position of 210 steps using the data from the Reactivity Briefing Sheet (from Reactivity Handbook)

DO NOT READ TASK STANDARD TO EXAMINEE Task Standard:

Determined that 928 (+/

- 5 ) gallons of primary water is required for the 10% power increase.

NRCL121-A6 PAGE 2 OF 5 R EV. 0 JPM TITLE: DETERMINE DILUTION REQUIREMENTS TO RAISE POWER JPM NUMBER: NRCL121-A6 EVALUATOR WORKSHEET Start Time:

Step Expected Operator Actions

1. Obtain the correct procedure.

1.1 **********************************

Cue: Provide examinee with reactivity briefing sheet, if not already done.

Sat: ______ Unsat _______

Comment: 2.0B** Calculate reactivity change for 10% change in power 2.1 From graph power coefficient is

-15.47 pcm/% power.

2.2 Record

ed (-)154.7 pcm for 10% increase in power.

- Sat: ______ Unsat _______

Comment: 3.1B** Calculate reactivity change due to change in rod position

3.1 Recorded

45.9 pcm for Control Bank D at 210 steps.

(From graph, A. Control Bank D Integral Rod Worth) 3.2 Recorded 98.1 pcm for Control Bank D at 2 00 steps.

(From graph, A. Control Bank D Integral Rod Worth) 3.3 Recorded (+)52.2 pcm for change in rod position.

- (98.1 - 45.9 ) Sat: ______ Unsat _______

Comment: NRCL121-A6 PAGE 3 OF 5 R EV. 0 JPM TITLE: DETERMINE DILUTION REQUIREMENTS TO RAISE POWER JPM NUMBER: NRCL121-A6 EVALUATOR WORKSHEET 4.2B** Calculate reactivity left after accounting change in rod position.

4.1 Recorded

(-)102.5 pcm

)reactivity from change in rods position on total reactivity from change in power.

- (-154.7 + 52.2) Sat: ______ Unsat _______

Comment: 5.3B** Determines amount of primary water to add Note: The examinee may set up a ratio to get the primary water needed, or may do two steps (determine power change needing dilution, and then dilution for that power change).

5.1 Determined

928 (+/- 5 ) gallons of primary water is required.

(102.5 pcm/15.47 pcm/% = 6.63 % pwr) (6.63% x 140 gal/% =

928 gallons (+/- 5 gallons) ** Note: The critical "part" of the above step is the dilution gallons, as the data can be manipulated several different ways in one or more steps to arrive at the right answer. Sat: ______ Unsat _______

Comment: Stop Time:

Total Time:

(Enter total time on the cover page)

Follow up Question Documentation

Question: ____________________________________________________________________

______________________________________________________________________________

Response: ___________________________________________________________________

______________________________________________________________________________

NRCL121-A6 PAGE 4 OF 5 R EV. 0 EXAMINEE CUE SHEET JPM NUMBER: NRCL121-A6 Initial Conditions:

Given: Unit 2 was ramped down due to high vibration on the main turbine.

Unit 2 has been at 80% power for 3 days.

Control Bank D is at 200 steps Initiating Cue:

The Shift Foreman directs you to determine the dilution or boration requirements to raise power to 90% assuming final rod position of 210 steps using the data from the Reactivity Briefing Sheet (from Reactivity Handbook)

Answer (show work)

NRCL121-A6 PAGE 5 OF 5 R EV. 0

NUCLEAR POWER GENERATION DIABLO CANYON POWER PLANT JOB PERFORMANCE MEASURE Number: NRCL081LJA_ROA1 Title: DETERMINE DILUTION REQUIREMENTS FOR A POWER INCREASE Examinee:

Evaluator:

Print Signature Date Results: Sat Unsat Total Time: minutes Comments:

References:

DCPP Unit 1 Cycle 16 Reactivity Briefing Sheet (9000 MWD/MTU) Alternate Path:

Yes No X Time Critical:

Yes No X Time Allotment:

15 Minutes Critical Steps:

2-6 Job Designation:

RO Task Number:

G2.1.25 Rating: 3.9 JOHN P. LYLE E D HURST AUTHOR: GARY HUTCHISON DATE: 12/10/09 R EV. 1 JPM TITLE: DETERMINE DILUTION REQUIREMENT S FOR A POWER INCREASE JPM NUMBER: NRCL081LJA_ROA1 INSTRUCTOR WORKSHEET Directions:

No plant controls or equipment are to be operated during the performance of this Job Performance Measure. All actions taken by the examinee should be clearly demonstrated and verbalized to the evaluator. The student will be given the initial conditions, initiating cue, and task standard. The examiner will then ask if any clarifications are needed. The examinee may be given the procedure and told the step with which to begin. Required Materials:

Calculator, Reactivity Briefing Sheet Initial Conditions:

Unit 1 was ramped down due to problems with Govenor valve 4. Unit 1 has been at 90% power for 3 days with Control Bank D at 200 steps. Initiating Cue:

Shift Foreman directs you to determine the dilution or boration requirements to increase power to 95% assuming final rod position of 210 steps using the data from the Reactivity Briefing Sheet. Task Standard:

Operator determines that 230 (+/- 5 ) gallons of primary water is required. NRCL081LJA_ROA1 rev 1.doc PAGE 2 OF 6 R EV. 1 JPM TITLE: DETERMINE DILUTION REQUIREMENT S FOR A POWER INCREASE JPM NUMBER: NRCL081LJA_ROA1 INSTRUCTOR WORKSHEET Start Time: StepExpected Operator Actions

1. Operator obtains correct procedure

1.1 Operator

obtains Reactivity Briefing Sheet. Note: Provide exam copy of Reactivity Briefing Sheet Step was: Sat: _______ Unsat _______*

2. ** Calculates reactivity from change in power 2.1 Operator determines that power coefficient is -12.57 pcm/% power. **

2.2 Operator

determines PCM for 5% increase in power. (-62.85 pcm) ** Step was: Sat: _______ Unsat _______*

3. **Calculates reactivity from change in rod position

3.1 Operator

determines PCM for Control Bank D at 210 steps. (28 pcm) **

3.2 Operator

determines PCM for Control Bank D at 200 steps. (59.8 pcm) **

3.3 Operator

determines PCM for change in rod position. (PCM at 200 - PCM at 220 steps = 31.8 pcm ) ** Step was: Sat: _______ Unsat _______*

Denotes an entry required on the JPM cover sheet. **Denotes a Critical Step.

NRCL081LJA_ROA1 rev 1.doc PAGE 3 OF 6 R EV. 1 JPM TITLE: DETERMINE DILUTION REQUIREMENT S FOR A POWER INCREASE JPM NUMBER: NRCL081LJA_ROA1 INSTRUCTOR WORKSHEET StepExpected Operator Actions

4. ** Calculates reactivity left after accounting change in rod position.

4.1 Accounts

for reactivity from change in rods position on total reactivity from change in power. (-62.8 + 31.8 =

-31.05 pcm)** Step was: Sat: _______ Unsat _______*

5. **Determines % power change from reactivity associated with dilution.

5.1 Determines

that 2.47 % power change is left to dilution water. (-31.05 pcm/

-12.57 pcm/% power)** Step was: Sat: _______ Unsat _______*

6. **Determines amount of primay water to add. 6.1 Determines that 230 (+/- 5 ) gallons of primary water is required. (2.47%

93 gal/% = 230 gallons) ** Step was: Sat: _______ Unsat _______*