Latest revision as of 23:45, 5 February 2020

Text

End of Interval Relief Requests Associated with the Fourth 10-Year Inservice Inspection (ISI) Interval
	ML14028A579
Person / Time
Site:	Oyster Creek
Issue date:	01/07/2014
From:	Jim Barstow; Exelon Generation Co
To:	; Document Control Desk, Office of Nuclear Reactor Regulation
References
	RA-14-001
	Download: ML14028A579 (254)
	v • d • e

A200 Exe!Lon Generation Exelon Way Kennett Square. PA 19348 www.exeloncorp.com 10 CFR 50.55a RA-14-001 January 7, 2014 U.S. Nuclear Regulatory Commission Attn: Document Control Desk Washington, DC 20555-0001 Oyster Creek Nuclear Generating Station Renewed Facility Operating License No. DPR-16 NRC Docket No. 50-219

Subject:

End of Interval Relief Requests Associated with the Fourth 10-Year Inservice Inspection (ISI) Interval In accordance with 10 CFR 50.55a, "Codes and standards," paragraph (a)(g)(5)(iii), Exelon Generation Company, LLC (Exelon) is requesting relief from the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel (B&PV) Code,Section XI, "Rules for Inservice Inspection of Nuclear Power Plant Components." These reliefs apply to the fourth 10-year Inservice Inspection (ISI) interval, which concluded on January 14, 2013 for the Oyster Creek Nuclear Generating Station. The fourth 10-year ISI interval complied with the ASME Boiler and Pressure Vessel Code, Section Xl, 1995 Edition with 1996 Addenda.

There are no regulatory commitments in this letter.

If you have any questions concerning this letter, please contact Tom Loomis at (610) 765-5510.

Respectfully, Jame arstow Director - Licensing & Regulatory Affairs Exelon Generation Company, LLC

Attachment:

Relief Requests R-44, R-45 cc: Regional Administrator, Region I, USNRC USNRC Senior Resident Inspector, OCNGS Project Manager [OCNGS] USNRC

ATTACHMENT Relief Requests R-44, R-45

Request for Relief (R-44) for Obtaining the Required Percentages During the Fourth Interval for Class 1 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 1 of 6) 1.0 ASME CODE COMPONENTS AFFECTED Code Class: 1

Reference:

Table IWB-2500-1 Examination Category: B-A, B-D, B-F Item Number: B1.12, B1.21, B1.22, B1.40, B3.90, B3.100 and B5.10

Description:

Relief for the 100% Volumetric Examination of the Class 1 Reactor Vessel Welds, Nozzle to Vessel Welds, Nozzle Inside Radius, and Dissimilar Metal Welds in Nozzles Component Number: See Table R-44 2.0 APPLICABLE CODE EDITION AND ADDENDA The fourth 10-year Inservice Inspection (ISI) interval program was based on the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel (B&PV)

Code,Section XI, 1995 Edition with 1996 Addenda.

3.0 APPLICABLE CODE REQUIREMENT ASME Section XI, 1995 Edition with 1996 Addenda, Examination Category B-A, Items B1.12, B1.21, B1.22, and B1.40, Examination Category B-D, Items B3.90 and B3.100, and Examination Category B-F, Item B5.10 require a 100% volumetric examination of reactor vessel welds, nozzle to vessel welds, nozzle inside radius and dissimilar metal welds in nozzles.

4.0 IMPRACTICALITY OF COMPLIANCE Pursuant to 10 CFR 50.55a(g)(5)(iii), relief is requested from the Code required 100%

volumetric examination of the reactor vessel welds, nozzle to vessel welds, nozzle inside radius, and dissimilar metal welds in nozzles that are listed in Table R-44, on the basis that conformance with these Code requirements is impractical due to component configuration and access restrictions.

Request for Relief (R-44) for Obtaining the Required Percentages During the Fourth Interval for Class I Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 2 of 6)

Table R Limited Weld Coverage Weld Description Coverage Item Att.# Notes NR02 1-574 Reactor Head to Flange 58% B13.40 Al Limited due to Flange Configuration NR02 2-562 Lower Head Circ Weld 65.7% B1.21 A2 Proximity of Skirt and N2 Nozzles NR02 2-563D Upper Intermediate Shell Course 64.3% B1.12 A3 Limited due to Feedwater Spargers, Core Spray Piping NR02 2-563E Upper Intermediate Shell Course 67.6% B1.12 A4 Limited due to Feedwater Spargers, Core Spray Piping NR02 2-563F Upper Intermediate Shell Course 53% B13.12 A5 Limited due to Feedwater Spargers, Core Spray Piping and Surveillance Specimen Bracket NR02 2-564A Lower Intermediate Shell Course 50.7% B13.12 A6 Limited due to Surveillance Specimen Basket and Shroud Repair Hardware NR02 2-564C Lower Intermediate Shell Course 49.4% B1.12 A7 Limited due to Shroud Repair Hardware NR02 2-564D Lower Shell Course Assembly 55.2% B1.12 A8 Proximity of Recirc Outlet Nozzle NR02 2-564E Lower Shell Course Assembly 48.3% B1.12 A9 Limited due to Shroud Repair Hardware and Recirc Outlet Nozzle NR02 2-564F Lower Shell Course Assembly 67.9% B1.12 A10 Limited due to Conical Support and Shroud Repair Hardware NR02 4-562A Lower Head Meridional 52.1% B1.22 All Proximity of Skirt and N2 Nozzle NRO2 4-562D Lower Head Meridional 84.2% B1.22 A12 Proximity of Skirt and N2 Nozzle NR02 4-562F Lower Head Meridional 84.2% B1.22 A13 Proximity of Skirt and N2 Nozzle

Request for Relief (R-44) for Obtaining the Required Percentages During the Fourth Interval for Class 1 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 3 of 6)

Table R Limited Weld Coverage Weld Description Coverage Item Att.# Notes NR02 3-565A NMA Recirc Outlet Nozzle 45.2% B3.90 A14 Nozzle Configuration NR02 3-565B N1B Recirc Outlet Nozzle 45.2% B3.90 A15 Nozzle Configuration NR02 3-565C N1C Recirc Outlet Nozzle 22% B3.90 A16 Nozzle Configuration, Insulation Support Ring, and UT Scanner Arm NR02 3-565D N1D Recirc Outlet Nozzle 22% B3.90 A17 Nozzle Configuration, Insulation Support Ring, and UT Scanner Arm NR02 3-565E N1 E Recirc Outlet Nozzle 47.9% B3.90 A18 Nozzle Configuration NR02 6-566A N3A Main Steam Nozzle 52.9% B3.90 A19 Nozzle Configuration NR02 6-566B N3B Main Steam Nozzle 52.9% B3.90 A20 Nozzle Configuration NR02 4-566A N4A Feedwater Nozzle 51.8% B3.90 A21 Nozzle Configuration and Proximity of N6A and N13B NR02 4-566B N4B Feedwater Nozzle 52.5% B3.90 A22 Nozzle Configuration NR02 4-566C N4C Feedwater Nozzle 49.5% B3.90 A23 Nozzle Configuration and Proximity of N6B and N15B NR02 4-566D N4D Feedwater Nozzle 52.5% B3.90 A24 Nozzle Configuration NR02 2-566A N5A Isolation 29% B3.90 A25 Nozzle Configuration and Proximity of N13, N14 and Condenser Nozzle _Insulation Support Ring NR02 2-566A N5A Isolation Condenser 78.9% B3.100 A26 Proximity of N13, N14 and Insulation Support Ring Nozzle Inner Radius NR02 2-566B N5B Isolation 22% B3.90 A27 Nozzle Configuration and Proximity of Insulation Support Condenser Nozzle Ring NR02 2-566B N5B Isolation Condenser 68.8% B3.100 A28 Proximity of Insulation Support Ring Nozzle Inner Radius NR02 2-567A N6A Core Spray Nozzle 28.1% B3.90 A29 Nozzle Configuration and Proximity of N13B and Bio-Shield Access Limitations NR02 2-567A N6A Core Spray Nozzle Inner 44% B3.100 A30 Nozzle Configuration and Proximity of N13B and Bio-Radius Shield Access Limitations

Request for Relief (R-44) for Obtaining the Required Percentages During the Fourth Interval for Class 1 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 4 of 6)

Table R Limited Weld Coverage Weld Description Coverage Item Att.# Notes NR02 2-567B N6B Core Spray Nozzle 61.7% B3.90 A31 Nozzle Configuration and Proximity to N15B and N16B Instrument Nozzles, and N4C NR02 2-567B N6B Core Spray Nozzle Inner 60.9% B3.100 A32 Nozzle Configuration and Proximity of the N15B and Radius N16B Instrument Nozzles NR02 1-576 N7A Closure Head Nozzle 76% B3.90 A33 Nozzle Configuration NR02 1-576 N7A Closure Head Nozzle 74% B3.100 A34 Nozzle Configuration (offset)

Inner Radius NR02 3-576 N7B Closure Head Nozzle 78% B3.90 A35 Nozzle Configuration NR02 3-576 N7B Closure Head Nozzle 88% B3.100 A36 Nozzle Configuration (offset)

Inner Radius NR02 5-576 N8 Closure Head Nozzle 89% B3.90 A37 Nozzle Configuration NR02 6-567 N9 CRD Return Nozzle 69% B3.90 A38 Nozzle Configuration NR02 5-567 N9 CRD Return Nozzle to Safe 67.4% B5.10 A39 Outer Diameter Safe End Configuration End NR02 4-565D NID Recirc Outlet Nozzle to 70% B5.10 A40 Nozzle Outer Diameter Configuration Safe End

Request for Relief (R-44) for Obtaining the Required Percentages During the Fourth Interval for Class 1 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 5 of 6) 5.0 BURDEN CAUSED BY COMPLIANCE Due to the component configuration, portions of the code required examination volume could not be completely examined. The curvature of the radius of the nozzle forging is such that ultrasonic scanning of the weld is interrupted due to loss of contact of the ultrasonic search unit. This limitation affects both transverse and parallel scanning of the code required examination volume.

In addition to component configuration, certain weld examinations are further limited by reactor pressure vessel design obstructions such as reactor pressure vessel appurtenances, bio-shield opening limitations, Outer Diameter (OD) contours, and mirror insulation. Examination coverage percentages are identified in Table R-44, and inspections were performed to the maximum extent practical for the given configuration.

The inspection results for the full penetration reactor vessel welds, nozzle to vessel welds, nozzle inside radius, and dissimilar metal welds in nozzles did not identify any unacceptable indications.

Oyster Creek Nuclear Generating Station requests relief from 100% volumetric examination of the full penetration reactor vessel welds, nozzle to vessel welds, nozzle inside radius and dissimilar metal welds in nozzles due to access limitations imposed by reactor pressure vessel design and/or component configuration.

6.0 PROPOSED ALTERNATIVE AND BASIS FOR USE No alternate provisions are practical for the subject welds. Examinations were performed to the maximum extent practical with the best available methods at the time of the examination.

7.0 DURATION OF PROPOSED ALTERNATIVE This relief is requested for the fourth 10-year ISI interval for Oyster Creek Nuclear Generating Station, which ended on January 14, 2013.

Request for Relief (R-44) for Obtaining the Required Percentages During the Fourth Interval for Class 1 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 6 of 6) 8.0 PRECEDENTS Similar relief requests have been approved for:

1) The Oyster Creek Nuclear Generating Station (OC-33 and OC-34), in U.S. Nuclear Regulatory Commission Safety Evaluation Report dated February 2, 2005.

2) The Limerick Generating Station, Units 1 and 2 (Relief Request RR-34) in a U.S.

Nuclear Regulatory Commission Safety Evaluation Report dated January 27, 2009.

3) The Peach Bottom Atomic Power Station, Units 2 and 3 (Relief Request 13R-48) in a U.S. Nuclear Regulatory Commission Safety Evaluation Report dated August 27, 2010.

Attachment:

Al Weld: NR02 1-574 Report Number: OCR20-037 Item Number: B1.40 Outage: 1 R20 (Fall 2004)

Coverage: 58%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-5, "Head to Flange" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 58% code required coverage due to the closure head flange configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A magnetic particle (MT) exam and a system pressure test were also completed with no unacceptable indications observed.

Oyster Creek nit-1 Flange Weld 60* NS Exam Volume = 9.8 Sq. In.

60° FV S6 Exam Volume = 23.2 Sq. In.

60° FV 54 Exam Volume = 5.2 Sq. In.

600 NS T-Scan achieved = 3.9 Sq. In.

600 FV S6 T-Scan achieved = 22.2 Sq. In.

60* FV S4 T-Scan achieved = 5.2 Sq. In.

60° NS P-Scan achieved = 3.0 Sq. In.

600 FV S6 P-Scan achieved = 10.4 Sq. In.

60° FV S4 P-Scan achieved = 2.3 Sq. In.

5.2" 3.1"

\

P-Scans 60°T NS 13.6" 60*T V

Nominal T and clad from CE Dwg. 232-574 Segments specification = 5 - 5/16" Nominal T = 5 - 5/16" Nominal Clad T = 7 / 32"

Attachment:

A2 Weld: NR02 2-562 Report Number: 1 R24-1 01 Item Number: B1 .21 Outage: 1R24 (Fall 2012)

Coverage: 65.7%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-3, "Spherical Vessel Head Circumferential and Meridional Weld Joints" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 65.7% code required coverage due to the proximity of the vessel skirt and N2 recirculation inlet nozzles. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

m m m m m m m. m m m M mIiI=

1111M m 2-574 3-574B i0 3-574C 180* >4-562E INSIDE VIEW OUTSIDE VIEW BO'TOM HEAD ASSEMBLY CLOSURE (TOP) HEAD ASSEMBLY CO)

O4"O Figure 2-2. Oyster.Creek Reactor Pressure Vessel Bottom and Top Heads Plate, Flange Forging, and Seam Weld Locations [10, 13, 14, 15, 16]

SIR-00-063, Rev. 0 2-15

H~HI NR02 4-562D

+. beve I 00000 I I -rd t

.of WcE Page of s-Report Number 1R24-123

Attachment:

A3 Weld: NR02 2-563D Report Number: 1 R24-105 Item Number: B1.12 Outage: 1 R24 (Fall 2012)

Coverage: 64.3%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-2, "Vessel Shell Longitudinal Weld Joints" UT Exam Type: Automated UT Scanning from Vessel ID Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 64.3% code required coverage due to the feedwater sparger, core spray piping and core spray risers adjacent to this weld. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

OYSTER CREEK Lcxelkbxe specwcn hoo6emloded 2110Saigle/ 3W0 W 0*18 270r 360(

EL 65911 VESSELFLANGE EL 636.9" 3-563 ELSO54 1-563 EL 390.W TOP OF SIELUJD EL 371.7 1-572 EL238.1" EL 106-"

3-572 2S6.5' EL 0.0" VESSELZEROELEVATION C-VESSELDIAMETERAT FLANGE= 213.0" AZIMUTHS= La6 INCHESPER DEGREE

Attachment:

A4 Weld: NR02 2-563E Report Number: 1R24-106 Item Number: B1.12 Outage: 1 R24 (Fall 2012)

Coverage: 67.6%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-2, "Vessel Shell Longitudinal Weld Joints" UT Exam Type: Automated UT Scanning from Vessel ID Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 67.6% code required coverage due to the feedwater sparger and core spray piping adjacent to this weld. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

OYSTER CREEK

0. 90" 180 27O" 36(0 EL 659.8 VESSELFLANGE EL636.9 3-563 EL 504.3 1-563 EL.390.0' TOPOF SHROUD EL. 371.7 1-572 EL 23&16 3-56'.

EL 106.5" 3-572 256-s.

EL .0" VESSELZERO ELEVATION VESSELOIAM1SERATFLANGE= 213.0' AZIMUTHS= L86 INCHESPER DEGREE GE NUCLEAR ENERGY OYSTER CREEK RPV EXAM AREAS SCALE: NONE DWG. OC-2012-01 REV. 0

Attachment:

A5 Weld: NR02 2-563F Report Number: 1 R24-107 Item Number: B1.12 Outage: 1 R24 (Fall 2012)

Coverage: 53%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-2, "Vessel Shell Longitudinal Weld Joints" UT Exam Type: Automated UT Scanning from Vessel ID Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 53% code required coverage due to the proximity of the feedwater sparger, core spray piping, and surveillance specimen bracket. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

OYSTER CREEK Sxwdiwe sp~weng~f hokoem boded M10Sulgle/ 300 WWo 0* 90" 180 360 EL.659" VESSELFLANGE EL 63&9ff 3-563 ELSO43" 1-563 EL 390.0" TOP OF SHROUD EL 390-W EL 371.7 EL238.1" 3-564 I iI EL 106.5" 3-572 2S6.5' EL O.0" VESSELZEROELEVATION r" -- I VESSELDIAMETERAT FLANGE= 213.0' AZIMUTHS= 1.86 INCHESPER DEGREE GE NUCLEAR ENERGY OYSTER CREEK RPV EXAM AREAS SCALE: NONEI DWG. OC-2012-01 REV. 0

Attachment:

A6 Weld: NR02 2-564A Report Number: 1R24-108 Item Number: B1.12 Outage: 1 R24 (Fall 2012)

Coverage: 50.7%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-2, "Vessel Shell Longitudinal Weld Joints" UT Exam Type: Automated UT Scanning from Vessel ID Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 50.7% code required coverage due to the proximity of a surveillance specimen basket and shroud repair tie rod. The following sketch contains the limitations.

No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

OYSTER CREEK Swevdiode speceoen hoklers WOWe 21(r S~o&i/ 30(r Od.o 0* 90~ 360' I . .

EL659 " VESSELFLANGE EL63&90 3-563 EL.504-7 1-563 EL 390L0 TOP OF SHROUD EL 3717" 1-572 EL 238&1 3-564 3-572 N I EL 1065" 2S&S' L

)l EL 0.(r VESSELZEROELEVATION VESSELDIAMETERAT FLANGE= 213,0" AZIMUTHS= L86 INCHESPER DEGREE GE NUCLEAR ENERGY OYSTER CREEK RPV EXAM AREAS SCALE: NONE I DWG. OC-2012-01 REV. 0

Attachment:

A7 Weld: NR02 2-564C Report Number: 1 R24-110 Item Number: B1.12 Outage: 1R24 (Fall 2012)

Coverage: 49.4%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-2, "Vessel Shell Longitudinal Weld Joints" UT Exam Type: Automated UT Scanning from Vessel ID Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 49.4% code required coverage due to the proximity of the shroud repair tie rod. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

OYSTER CREEK Someve~oce specim~en hOkdeskooded21i' Soigle/ 3W0DdW 0 90' 160' 270' 360o EL 6590" VESSELFLANGE EL 636.99 3-563 EL 50.3" 1-563 EL 390.0' TOP OF SHROUD EL 3?Lr 1-572 EL 238.1" 3-564 I EL 106.5" 256.S' EL 0.0' VESSELZEROELEVATION C-VESSELDIAM'ETERAT FLANGE= 213.0*

AZIMUTHS- 186 INCHESPER DEGREE GE NUCLEAR ENERGY OYSTER CREEK RPV EXAM AREAS FSCALE: NONE DWG. OC-2012- 1 REV. 0

Attachment:

A8 Weld: NR02 2-564D Report Number: 1R24-1 11 Item Number: B1.12 Outage: 1 R24 (Fall 2012)

Coverage: 55.2%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-2, "Vessel Shell Longitudinal Weld Joints" UT Exam Type: Automated UT Scanning from Vessel ID Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 55.2% Code required coverage due to the proximity of the recirculation outlet nozzle. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

OYSTER CREEK Sum*Wwtc'.

specwryef &oodd21(r 5ingW Wc~d'.s / 3W Dual 0O 90' 180" 270' 360

. . - I I . . , ý , , ý , , .

EL659.8 VESSELFLANGE EL 636.9' 3-563 EL.S043' 1-563 EL 390.0' TOP OF SHROUD EL 371.7 1-S72 EL 238.1' 3-564 EL 106.5° 3-572 256.S' EL 0.(r VESSELZEROELEVATION VESSELDIAMETER AT FLANGE = 213.0 AZIMUTHS= 186 INCHESPER DEGREE GE NUCLEAR ENERGY OYSTER CREEK RPV EXAM AREAS SCALE: NONE DWG. OC-2012-01 REV. 0

Attachment:

A9 Weld: NR02 2-564E Report Number: 1R24-112 Item Number: B1.12 Outage: 1R24 (Fall 2012)

Coverage: 48.3%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-2, "Vessel Shell Longitudinal Weld Joints" UT Exam Type: Automated UT Scanning from Vessel ID Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 48.3% code required coverage due to the proximity of the shroud repair tie rod and the recirculation outlet nozzle. The following sketch contains the limitations.

No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

OYSTER CREEK S..ýW~once specanean hokiers Wowe2L10Swt&I/ 3W 0,Wi O" 90" 180" 270 360 EL 659.8' VESSELFLANGE EL 636.9*

3-563 EL S04.3 1-56.3 EL. 390.0" TOP OF SHROIJD EL.390.0' TOPOFSHROUD EL 371.7 1-572 EL23&1 3-564.

EL 10.W 2S6.5*

EL 0.0" VESSELZEROELEVATION r" -'3 VESSELDIAMET1ER AT FLANGE= 213.Or AZIMUTHS- 18 INCHESPER DEGREE GE NUCLEAR ENERGY OYSTER CREEK RPV EXAM AREAS SCALE: NONE DWG. OC-2012-O1 I REV. 0

Attachment:

A10 Weld: NR02 2-564F Report Number: 1 R24-113 Item Number: B1.12 Outage: 1 R24 (Fall 2012)

Coverage: 67.9%

Base Metal and Weld Materials: Carbon Steel Examination Volume: Coverage per figure IWB-2500-2, "Vessel Shell Longitudinal Weld Joints" UT Exam Type: Automated UT Scanning from Vessel ID Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 67.9% code required coverage due to the proximity of the conical support and shroud repair tie rod. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

OYSTER CREEK Survedlome specv.en hcoderiloaded2107S&ngt/3WdDual 0 91waO 2?0* 364r EL6S9 8" VESSELFLANGE EL 636.9" 3-563 EL.504-3" 1-563 EL 3900' TOP OF SHIOUD EL 371.7" 1-Sn2 EL 23&.1 3-564 I

11 tI I EL 106.S 3-572 256.5 EL 0.0* VESSELZEROELEVATION VESSELDIAMETERAT FLANGE= 213.0' AZIMUTHS= L86 INCHESPER DEGREE GE NUCLEAR ENERGY OYSTER CREEK RPV EXAM AREAS SCALE: NONE DWG. OC-2012-01 REV. 0

Attachment:

Al 1 Weld: NR02 4-562A Report Number: 1 R24-120 Item Number: B13.22 Outage: 1R24 (Fall 2012)

Coverage: 52.1%

Base Metal and Weld Materials: Carbon Steel - Lower Head Meridional Weld Examination Volume: Coverage per figure IWB-2500-3, "Spherical Vessel Head Circumferential and Meridional Weld Joints" UT Exam Type: Manual UT Scanning of Vessel Bottom Head from 01 Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 52.1% code required coverage due to the proximity of the RPV skirt and recirculation N2 nozzle. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

HONCHI NO .

_________~NR0 4-562A_ _____(41

~ ~~ii'~,iLo~o,~~i.~ai ioo~ri ~ a~.~c &jd 0 p f ~.,cL uoc ~ well~

ct WCi to Jc

-Report Number: Page24-120'

Attachment:

A12 Weld: NR02 4-562D Report Number: 1 R24-123 Item Number: B1.22 Outage: 1 R24 (Fall 2012)

Coverage: 84.2%

Base Metal and Weld Materials: Carbon Steel - Lower Head Meridional Weld Examination Volume: Coverage per figure IWB-2500-3, "Spherical Vessel Head Circumferential and Meridional Weld Joints" UT Exam Type: Manual UT Scanning of Vessel Bottom Head from the OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 84.2% code required coverage due to the proximity of the RPV skirt and recirculation N2 nozzle. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

.-- NR02 4-562D ce5.s ;)le 40be 7"

7- 5/ ;

RNR- n*ot .,l ./.o

' a, Pa Page (- of S Report Number: IR24-123

Attachment:

Al 3 Weld: NR02 4-562F Report Number: 1R24-125 Item Number: B1.22 Outage: 1R24 (Fall 2012)

Coverage: 84.2%

Base Metal and Weld Materials: Carbon Steel - Lower Head Meridional Weld Examination Volume: Coverage per figure IWB-2500-3, "Spherical Vessel Head Circumferential and Meridional Weld Joints" UT Exam Type: Manual UT Scanning of Vessel Bottom Head from OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 84.2% code required coverage due to the proximity of the RPV skirt and recirculation N2 nozzle. The following sketch contains the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

I*," NRO2 4-562F A"

A' A'

A N

A 7

A 71 r\) J, II

/

7 *9e * ---.......__..*

7.*m

-4 - .-

w.LJ ~

V-~. IO Page

of Report Number: IR24-125 5

Attachment:

A14 Weld: NR02 3-565A (N1A)

Report Number: 1R22-126 Item Number: B3.90 Outage: 1R22 (Fall 2008)

Coverage: 45.2%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 45.2% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

HITACHI Reactor PressureVessel Coverage TAC CalculationSheet Oyster Creek N1A - Recirc Outlet CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 75.9 IRS-Scan LKCW IS4) A 9.5 9.5 12.5% 360 3.1%

IRS-Scan LKCCW 6$41 A 9.5 9.5 12.5% 360 3.1%

600 P-Scan (S61 A 66.4 13.5 17.8% 360 8.9%

600 T-Scan (54) A 9.5 9.5 12.5% 360 6.3%

600 T-Scan (S6) A 66.4 36.1 47.6% 360 23.8%

__ ____ i____ _ _

% Total Composite Coverage = 45.2%

Rev.0 9/23iQE Comments A - Scanned area 3600. Scanning limited due to nozzle configuration.

Note - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume. S6-Supplement 6 volume. Weld length in degrees.

-~~L w w-9a M.eS r

0 Ln (D

Oyster Creek' 0D Recirc Outlet 0o 60° 54 Exam Volume = 9.5 Sq. In.

600 S6 Exam Volume = 66.4 Sq. In.

600 S4 IRS-Scan LKCW achieved = 9.5 Sq. In.

600 S4 IRS-Scan LKCCW achieved = 9.5 Sq. In.

60° S6 P-Scan achieved = 13.5 Sq. In.

600 S4 T-Scan achieved = 4.0 Sq. In.

600 S6 T-Scan achieved = 36.1 Sq. In.

£2"P-Ske*

/

/ 7.1" 16.7" 600P 60 0 T I II I

L

-1

' Radial Plate T Nom. = 7.125" I r1nr4 T hInrn -_ r ' 01.7r"

Attachment:

Al5 Weld: NR02 3-565B (NI B)

Report Number: OCL R22-128 Item Number: B3.90 Outage: 1 R22 (Fall 2008)

Coverage: 45.2%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 45.2% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

HITACHI Reactor PressureVessel Coverage CalculationSheet Oyster Creek NIB - Recirc Outlet CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 75.9 IRS-Scon LKCW (S4) A 9.5 9.5 12.5% 360 3.1%

IRS-Scan LKCCW (S4) A 9.5 9.5 12.5% 360 3.1%

600 P-Scan (S6) A 66.4 13.5 17.8% 360 8.9%

60" T-Scan (S4) A 9.5 9.5 12.5% 360 6.3%

600 T-Scan IS6) A 66.4 36.1 47.6% 360 23.8%

% Total Composite Coverage = 45.2%

Rev.0 9/23/0ý Comments A - Scanned area 3600. Scanning limited due to nozzle configuration.

o/ 7 Note - Rounding methods may affect calculated values. S4-Supplement 4 underclod volume, S6-Supierment 6 volume. Weld length in degrees.

0 C.D Oyster Creek C)

(D Recirc Outlet C) 0 60' S4 Exam Volume = 9.5 Sq. In.

600 S6 Exam Volume = 66.4 Sq. In.

600 S4 IRS-Scan LKCW achieved = 9.5 Sq. In.

60° 54 IRS-Scan LKCCW achieved = 9.5 Sq. In.

60' S6 P-Scan achieved = 13.5 Sq. In.

600 S4 T-Scan achieved = 4.0 Sq. In.

600 S6 T-Scan achieved = 36.1 Sq. In.

/

/ 16.7"

/ 60°T/P 60"P 60°T I I I I I

Radi,* te T Nom. = 7.125" Clad m. = 0..21875"

Attachment:

A16 Weld: NR02 3-565C (N1C)

Report Number: 5076 Item Number: B3.90 Outage: 1R20 (Fall 2004)

Coverage: 22%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Automated UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 22% code required coverage due to the nozzle configuration, proximity of the insulation support ring, and optimized UT scanner arm length. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

0 C 0

(A~

(D Oyster Creek (D RECIRCULATION OUTLET NIC 70' P-Scan Exam Volume - 20.88 Sq. In.

45" P-Scan Exam Volume - 45.03 Sq. In.

70" P-Scan achieved - 1.28 Sq. In.

450 P-Scan achieved - 6.86 Sq. In.

CD

(2 C. C--

0 (n CD C-)

~~1 Oyster Creek CD CD RECIRCULATION OUTLET NiC 700 T-Scan Exam Volume - 20.88 Sq. In.

450 T-Scan Exam Volume - 45.03 Sq. In.

60* T-Scan Exam Volume - 8.59 Sq. In.

0 700 T-Scan achieved - 1.37 Sq. In.

45° T-Scan achieved - 20.39 Sq. In.

60" T-Scan achieved - 8.59 Sq. In.

/

-u /

a I (a

CD K

0

-4' I;

C C11 restricted kby insudotion support ring Insu(ation support ring 2100 3290 NIC V

C, rn 00 Ci2

~11 ~

I,,

NIC TL auto exam

C C-0.

Area restric~ted by insutation support ring 960 3170 2210 NiC co cq NIC 70TP auto exam area

-n =i Fn

- r

Q Area restricted by insu~ation support ring 96*

3170~

221° NiC Cl) oC-) NIC 45° P1 auto exam area

0)0 c5

03) o 0 0viL OJ d F-

- ~E d x

0 0) a 0 UU d

.o -P

-P L iD d 0

-,43 cl*

C U 0 c5

-0P .

u n 0o 0 U 4-P

0) CC) k.D OYSTER CREEK R

PAGE \ OF \'-

G- Cep 0 Inspection Report No.: 005076 0,

CD Recirculation Outlet Ni-C CD (D Oyster Creek, 2004 CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 74.5 Area Sq. In. Auto Auto Auto Auto 70' T-Scan 20.88 1.37 1.8% 264 0.7%

450 T-Scan 45.03 20.39 27.4% 241 9.2%

600 T-Scan 8.59 8.59 11.5% 241 3.9%

700 P-Scan 20.88 1.28 1.7% 264 0.6%

450 P-Scan 45.03 6.86 9.2% 264 3.4%

Inner 15%T P-Scan 8.59 8.59 11.5% 263.6 4.2%

70* T-S can 450 T-Scan 0 600 T-Scan 700 P-Scan 450 P-Scan Inner 15%T P-Scan 700 T-Scan 450 T-Scan 600 T-Scan 700 P-Scan 450 P-Scan Inner 15%1 P-Scan

% Total Composite Coverage = 22%

Comments:

Inner 15%T P-Scan area by modeling.

Note - Rounding methods may make calculated values appear in error.

Attachment:

Al 7 Weld: NR02 3-565D (N1D)

Report Number: 5077 Item Number: B3.90 Outage: 1 R20 (Fall 2004)

Coverage: 22%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Automated UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 22% code required coverage due to the nozzle configuration and proximity of the insulation support ring. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

&_, 0 0C 0

(D ID 0 Oyster Creek CD (D

RECIRCULATION OUTLET N1D 700 T-Scan Exam Volume - 20.88 Sq. In.

450 T-Scan Exam Volume - 45.03 Sq. In.

60' T-Scan Exam Volume - 8.59 Sq. In.

70' T-Scan achieved - 1.37 Sq. In.

450 T-Scan achieved - 20.39 Sq. In.

60' T-Scan achieved - 8.59 Sq. In.

0 (D

I I

0

-4%

)

0 1)

Oyster Creek RECIRCULATION OUTLET N1D 0

70" P-Scan Exam Volume - 20.88 Sq. In.

45" P-Scan Exam Volume - 45.03 Sq. In.

70" P-Scan achieved - 1.28 Sq. In.

450 P-Scan achieved - 6.86 Sq. In.

-0 (D

C)y 0

V) E' c C5 0 0

3 ofi .E C5 cc5 0p 0 0-0 75

0 0)

C. 0 0-i z CC a) IF o F PAG OYSTER CREEK k R Z --z PAGE EL OF VC

ILI ci) 0 Ln (Y) d

-P*

+>J d

0 a) E

- 0 0~

0 4->

0 *- -

4-> 0 :3 C- c:

CC

>* __0

>2 -0 c5

-P5 U>U u

4- 0 0)i OYSTER CREEK

\ R z--. ,

PAGE "I OF k

0I) Lo) iio d

+> d 0

s~ E:

oS n 0)

Cl 0) 0 :

0 d

-P d n3

-P ~- c ci 1Uf

-~ :3 -H 0)

-0 4-P 75

+->~

0)0 OYSTER CREEK k R2-PAGE N 0 OF

c C, C Area. restricted b0y insuilction support ring 315.30 215.20~

NID NI.D P-Scan inner 15% auto exam area

ýw (214 e 0 Inspection Report No.: 005077 CD I

0 Recirculation Outlet N1-D x- Oyster Creek, 2004 0, CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld 'Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 74.5 Area Sq. In. Auto Auto Auto Auto 700 T-Scan 20.88 1.37 1.8% 260 0.7%

450 T-Scan 45.03 20.39 27.4% 241 9.2%

600 T-Scan 8.59 8.59 11.5% 241 3.9%

700 P-Scan 20.88 1.28 1.7% 260 0.6%

450 P-Scan 45.03 6.86 9.2% 260 3.3%

Inner 15%T P-Scan 8.59 8.59 11.5% 260 4.2%

CD (0 700 T-Scan CD 450 T-Scan 0 600 T-:Scan 700 P-Scan 450 P-Scan Inner 15%1r P-Scan 700 T-Scan 450 T-Scan 600 T-Scan 7Q0 P-Scan 450 P-Scan Inner 15%T P-Scan 01 % Total Composite Coverage = 22%

Comments:

Inner 15%T P-Scan area by modeling.

Note - Rounding methods may make calculated values appear in error.

I I I I

I l

Attachment:

A18 Weld: NR02 3-565E (NIE)

Report Number: 1R21-199 Item Number: 63.90 Outage: 1 R21 (Fall 2006)

Coverage: 47.9%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 47.9% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

0 CD 0

0 Oyster Creek N1 Nozzle- Recirculation Outlet 60' NS Exam Volume = 20.9 Sq. In.

60' FV Exam Volume = 44.1 Sq. In.

600 (Inner 15% T) Exam Volume = 9.5 Sq. In.

600 NS Coverage achieved = 1.9 Sq. In.

600 FV Coverage achieved = 16.7 Sq. In.

60' (Inner 15% T) Coverage achieved 4.9 Sq. In.

//

/ 60'P 60 0P 60 0 P CDI II I-----------

0 CD CD 0

0 Oyster Creek N1 Nozzle - Recirculation Outlet 60' NS Exam Volume = 20.9 Sq. In.

60* FV Exam Volume = 44.1 Sq. In.

600 (Inner 15% T) Exam Volume = 9.5 Sq. In.

60' NS Coverage achieved = 2.6 Sq. In.

600 FV Coverage achieved = 35.7 Sq. In.

600 (Inner 15% T) Coverage achieved = 9.5 Sq. In.

/

/ 60°T 60°T 6° I.

it1

CD CD CD C) 0 Oyster Creek N1 Nozzle - Recirculation Outlet 450 Shear nozzle to vessel proposed scan coverage Rotation skew angle +/-54° to 780 5478

/

(I Skew Angle CD 0

0 CD CD C) a)

Oyster Creek N 1 Nozzle - Recirculation Outlet 600 RL P-Scan proposed scan coverage Rotation skew angle +/-580 CD

/ 58°

/

'I Skew Angle

0 1<

0 CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = . Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 74.5 Area Sq. In. Manual Manual Manual Manual 60" NS T-Scan _______,_"__ 3.5% _ -____ 1.7%

60° S6 T-Scan _ ,__" :" 47.9% _ __, 24.0%

600 S4 T-Scan . 12.8% _ _ _ 6.4%

600 NS P-Scan - 20.9 2.6% _ .... 1.3%

60° S6 P-Scan 44.1 22.4% 11.2%

600 S4/IRS Scan 9.5 6.6% 3.3%

600 NS T-Scan _ 0.0% 0.0%

600 S6 T-Scan "__ _0.0% 0.0%

600 S4 T-Scan 0.0% __0.0%

600 NS P-Scan 20.9 ____0.0% 0.0%

600 S6 P-Scan 44.1 _ _ _ 0.0% 0.0%

60=S4/IRS Scan 9.5 0.0% 0.0%

i I li

% Total Composite Coverage = 47.9%

Comments:

0 n Noe-Rudn-etos8yafc.cluae aus

ýNote - Rounding methods may affect calculated values.

Attachment:

A19 Weld: NR02 6-566A (N3A)

Report Number: 1R21-142 Item Number: B3.90 Outage: 1 R21 (Fall 2006)

Coverage: 52.9%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 52.9% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

0 CD 0D CD CD Oyster Creek N3 Nozzle - Main Steam 60' RL T-Scan proposed examination coverage 20.2" 0 /

/

60'T 160'T

0 CD CD C)

Oyster Creek N3 Nozzle - Main Steam 60' RL P-Scan proposed examination coverage Rotation skew angle +/-580 CD

/

0)

/

605p I Skew Angle

-t 1-0

/

~1 CA CD Oyster Creek N3 Nozzle - Main Steam CD 600 NS Exam Volume 20.3 Sq. In.

600 FV Exam Volume = 44.3 Sq. In.

600 (Inner 15% T) Exam Volume = 9.6 Sq. In.

60 NS Coverage achieved = 2.3 Sq. In.

60° FV Coverage achieved = 20.8 Sq. In.

60° (Inner 15%oT) Coverage achieved = 6.7 Sq. In.

£

/

/ 600P 600P 600P

( I 1 I

'0 I

/

CD Oyster Creek N3 Nozzle - Main Steam CD 600 NS 60' Exam Volume FV Exam Volume == 44.3 20.3 Sq.

Sq. In.

In.

60° (Inner 15% T) Exam Volume = 9.6 Sq. In.

600 NS Coverage achieved = 2.6 Sq. In.

60' FV Coverage achieved = 36.5 Sq. In.

60' (Inner 15%-T) Coverage achieved = 9.6 Sq. In.

//

t 600T 60°T 60 0T I

I I I '1ý CD 10

--- "1

(D CD C3 Oyster Creek N3 Nozzle - Main Steam 45°Shear nozzle to vessel proposed examination coverage Rotation skew angle +/-540 to 78° 780 CD I' 540 Se\

NN NNV Skew Angle I

CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 74.2 Area Sq. In. Manual Manual Manual Manual 60* NS T-Scan - 3.5% _ .__, 1.8%

60' S6 T-Scan ._.... 49.2% *_24.6%

60' S4 T-Scan 12.9% 6.5%

600 NS P-Scan 20.3 3.1% : 1.5%

600 S6 P-Scan 44.3 28.0%, 14.0%

600 S4/IRS Scan 9.6 9.0% 4.5%

60° NS T-Scan 0.0% 0.0%

60_ S6 T-Scan 0,00% 0.0%

600 S4 T-Scan "0.0% 0.0%

600 NS P-Scan 20.3 0.0% 0.0%

600 S6 P-Scan 44.3 , 0.0% 0.0%

60°S4/IRS Scan 9.6 0.0% 0.0%

% Total Composite Coverage = 52.9%

Comments:

Note - Rounding methods may affect calculated values.

Attachment:

A20 Weld: NR02 6-566B (N3B)

Report Number: 1R21-144 Item Number:. B3.90 Outage: 1 R21 (Fall 2006)

Coverage: 52.9%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Head or Shell" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 52.9% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

0 (D

CD C3 Cn Oyster Creek N3 Nozzle - Main Steam 450 Shear nozzie to vessel proposed examination coverage Rotation skew angle +/-54° to 780 78° 0

Nen 540 NN NNV Skew Angle SI

0 (1)

CD CD 0

Oyster Creek N3 Nozzle - Main Steam 60* NS Exam Volume = 20.3 Sq. In.

600 FV Exam Volume = 44.3 Sq. In.

600 (Inner 15% T) Exam Volume = 9.6 Sq. In.

600 NS Coverage achieved = 2.3 Sq. In.

600 FV Coverage achieved = 20.8 Sq. In.

600 (Inner 15%-T) Coverage achieved = 6.7 Sq. In.

£

/

/ 60°P 60"P 600P

/

I I

CD Oh I

0~\

Cý Oyster Creek N3 Nozzle - Main Steam 600 RL P-Scan proposed examination coverage Rotation skew angle +/-580

_0 0) 580 SOT Skew Angle to CD I4

QJ 0

CD (D

0 Oyster Creek N3 Nozzle - Main Steam 600 NS Exam Volume =20.3 Sq. In.

60' FV Exam Volume = 44.3 Sq. In.

60" (inner 15% T) Exam Volume = 9.6 Sq. In.

60' NS Coverage achieved = 2.6 Sq. in.

600 FV Coverage achieved =36.5 Sq. In.

60*(inner 15%-T) Coverage achieved =9.6 Sq. In.

/I 60 0T 600T 600T 0..

0 CD 0

CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 74.2 Area Sq. In. Manual Manual Manual Manual 600 NS T-Scan '_-___ 3.5% 1.8%

600 S6 T-Scan -_. 49.2% . 24.6%

600 S4 T-Scan 12.9% 6.5%

60° NS P-Scan 20.3 3.1% ' 1.5%

60° S6 P-Scan 44.3 28.0%._"" 14.0%

60° S4/IRS Scan 9.6 ' _ 9.0% '_" 4.5%

60° NS T-Scan -10.0% 0.0%

60° S6 T-Scan '__J0.0% 0.0%

60' S4 T-Scan 0.0% 0.0%

60° NS P-Scan 20.3 0.0% 0.0%

600 S6 P-Scan 44.3 -_" 0.0% 0.0%

60 0S411RS Scan 9.6 0.0% 0.0%

I I I

% Total Composite Coverage = 52.9%

CD Comments:

H. Note - Rounding methods may affect calculated values.

Attachment:

A21 Weld: NR02 4-566A (N4A)

Report Number: 1R23-117 Item Number: B3.90 Outage: 1R23 (Fall 2010)

Coverage: 51.8%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Head or Shell" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 51.8% code required coverage due to the nozzle configuration and proximity of the N6A and N13B nozzles. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

0 SOyster Creek (Feedwater (D

6 o 600 S4 Exam Volume = 7.6 Sq. In.

600 S6 Exam Volume = 71.7 Sq. In.

600 S4 IRS-Scan LKCW achieved = 7.6 Sq. In.

600 S4 IRS-Scan LKCCW achieved = 7.6 Sq. In.

600 S6 P-Scan achieved = 26.0 Sq. In.

600 S4 T-Scan achieved = 7.6 Sq. In.

60° S6 T-Scan achieved = 42.1 Sq. In.

/

//

/ *

/ *60°T/P 10.2"

/600P 060°T Radial Plate T Nom. =7.125" Clad T Nom. = 0.21875

0 AD Oyster Creek (D

(D Feedwater C) 60° S4 Exam Volume = 7.6 Sq. In.

600 S6 Exam Volume = 71.7 Sq. In.

60' S4 IRS-Scan LKCW achieved = 7.6 Sq. In.

600 S4 IRS-Scan LKCCW achieved = 7.6 Sq. In.

60° S6 P-Scan achieved = 26.0 Sq. In.

600 S4 T-Scan achieved = 2.6 Sq. In.

60' 56 T-Scan achieved = 39.2 Sq. In.

/ N4A Scanning limited by N13B and N6A nozzles.

60°T/P

_0 10.2" 60 0 P 20.0" 60 0T 0

hr Radial Plate T Nom. = 7.125" Clad T Nom. = 0.21875"

N14B to 1660 N6A

-0 0

(D of the N6A and N13B nozzles.

0

HITACHI Reactor PressureVessel Coverage Calculation Sheet Oyster Creek N4A - Feed Water CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 79.3 IRS-Scon LKCW (S4) A 7.6 7.6 9.6% 306 2.0%

IRS-Scan LKCCW (S4) A 7.6 7.6 9.6% 306 2.0%

600 P-Scan (S6) A 71.7 26.0 32.8% 306 13.9%

600 T-Scan (S4) A 7.6 7.6 9.6% 306 4.1%

600 T-Scan (S6) A 71.7 42.1 53.1% 306 22.6%

IRS-Scan LKCW IS4) B 7.6 7.6 9.6% 54 0.4%

IRS-Scan LKCCW {S4) B 7.6 7.6 9.6% 54 0.4%

600 P-Scan (S6) B 71.7 26.0 32.8% 54 2.5%

60° T-Scan (S4) B 7.6 2.6 3.3% 54 0.2%

600 T-Scan (S6) B 71.7 39.2 49.4% 54 3.7%

~0 0

(0 __ ___ _ __ _ _ _ _ 1 _ _ _ __ _ _ _II_______ I __ _ _ _ _ _ _I _ _ _ _ _ _ _

& & I &

a

-0,

% Total Composite Coverage = 51.8%

Rav 0 W3?1I05 Comments A - Scanned area 220' CW to 1660. Scanning limited due to nozzle configuration.

~Ji B - Scanned area 1660 CW to 220'. Scanning limited due to nozzle configuration and nozzles N6A and N13B Note - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume. S6-Supplement 6 volume. Weld length indegrees

Attachment:

A22 Weld: NR02 4-566B (N4B)

Report Number: 1R23-118 Item Number: 63.90 Outage: 1R23 (Fall 2010)

Coverage: 52.5%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 52.5% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

° * *Oyster Creek '

(Feedwater co 600 S4 Exam Volume 7.6 Sq. In.

600 S6 Exam Volume = 71.7 Sq. In.

600 54 IRS-Scan LKCW achieved = 7.6 Sq. In.

600 S4 IRS-Scan LKCCW achieved = 7.6 Sq. In.

600 S6 P-Scan achieved = 26.0 Sq. In.

600 S4 T-Scan achieved = 7.6 Sq. In.

-1 60° S6 T-Scan achieved = 42.1 Sq. In.

/

// / I* 60°T/P 10.2" I * *600° Q

0 Radial Plate T Nom. = 7.125" Clad T Nom. = 0.21875"

HITACHI Reactor PressureVessel Coverage HITACHICalculation Sheet Oyster Creek N4B - Feed Water CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 79.3 IRS-Scan LKCW (S4) A 7.6 7.6 9.6% 360 2.4%

IRS-Scan LKCCW (S4) A 7.6 7.6 9.6% 360 2.4%

600 P-Scan (S61 A 71.7 26.0 32.8% 360 16.4%

600 T-Scon (54) A 7.6 7.6 9.6% 360 4.8%

600 T-Scan (S61 A 71.7 42.1 53.1% 360 26.5%

-u C

(0 0 % Total Composite Coverage = 52.5%

R.*e 0 9M2/04.

Comments A - Scanned area 360'. Scanning limited due to nozzle configuration.

~JJ Note - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume. S6-Supplement 6 volume. Weld length in degreeE

Attachment:

A23 Weld: NR02 4-566C (N4C)

Report Number: 1 R23-119 Item Number: B3.90 Outage: 1 R23 (Fall 2010)

Coverage: 49.5%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 49.5% code required coverage due to the nozzle configuration and the proximity of the N6B and N15B nozzles. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

0 Oyster Creek (D

SFeedwater X_

C o 60' S4 Exam Volume 7.6 Sq. In.

600 S6 Exam Volume = 71.7 Sq. In.

600 S4 IRS-Scan LKCW achieved = 7.6 Sq. in.

60° S4 IRS-Scan LKCCW achieved = 7.6 Sq. In.

600 S6 P-Scan achieved = 26.0 Sq. In.

600 S4 T-Scan achieved = 7.6 Sq. In.

600 S6 T-Scan achieved = 42.1 Sq. In.

/

60T/ 10.2" 060oP S20.0" I

60°T 0

Radial Plate T Nom. =7.125" Clad T Nom. = 0.21875"

0 1<

Ln Oyster Creek' (D

(D Feedwater N) 0 600 S4 Exam Volume = 7.6 Sq. In.

600 S6 Exam Volume = 71.7 Sq. In.

600 S4 IRS-Scan LKCW achieved = 7.6 Sq. In.

600 S4 IRS-Scan LKCCW achieved = 7.6 Sq. In.

600 S6 P-Scan achieved = 15.2 Sq. In.

600 S4 T-Scan achieved = 2.6 Sq. In.

600 S6 T-Scan achieved = 11.5 Sq. In.

/

N4C Scanning limited by N15B nozzle.

5.0" 60°T/P 39P-Sku~.

I 0

Radial Plate T Nom. = 7.125" Clod T Nom. = 0.21875"

I 0

Ln Oyster Creek (D

(D Feedwater C)

I-60° S4 Exam Volume = 7.6 Sq. In.

600 S6 Exam Volume = 71.7 Sq. In.

60° S4 IRS-Scan LKCW achieved = 7.6 Sq. In.

60° S4 IRS-Scan LKCCW achieved = 7.6 Sq. In.

600 S6 P-Scan achieved = 26.0 Sq. In.

600 S4 T-Scan achieved = 4.0 Sq. In.

600 S6 T-Scan achieved = 41.1 Sq. In.

/

N4C Scanning limited by N6B nozzle.

\/ 10.2" 60 0P 15.0" 60°T 7

0 D

L 0

Radial Plate T Nom. = 7.125" Clad T Nom. = 0.21875"

N15B N9 N16B CW to N17B N6Bp roximity 0-(V 01 Scanning of the limited N6B anddueN15B to the nc

Reactor Pressure Vessel Coverage Calculation Sheet Oyster Creek N4C - Feed Water CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 79.3 IRS-Scan LKCW (S4) A 7.6 7.6 9.6% 291 1.9%

IRS-Scan LKCCW (S4) A 7.6 7.6 9.6% 291 1.9%

600 P-Scan (S6) A 71.7 26.0 32.8% 291 13.3%

600 T-Scan (S4) A 7.6 7.6 9.6% 291 3.9%

60' T-Scon ($6) A 71.7 42.1 53.1% 291 21.5%

IRS-Scan LKCW (54) B 7.6 7.6 9.6% 35 0.2%

IRS-Scan LKCCW (S4) B 7.6 7.6 9.6% 35 0.2%

600 P-Scan (S6) B 71.7 26.0 32.8% 35 1.6%

600 T-Scan (S4) B 7.6 4.0 5.0% 35 0.2%

600 T-Scan (S6) B 71.7 41.1 51.8% 35 2.5%

IRS-Scan LKCW (S4) C 7.6 7.6 9.6% 34 0.2%

IRS-Scan LKCCW (S4) C 7.6 7.6 9.6% 34 0.2%

60° P-Scan (S6) C 71.7 15.2 19.2% 34 0.9%

600 T-Scon (S4) C 7.6 2.6 3.3% 34 0.2%

600 T-Scan (S6) C 71.7 11.5 14.5% 34 0.7%

CD LO 0 % Total Composite Coverage = 49.5%

Rev. 0 iments A - Scanned area 220° CW to 1660. Scanning limited due to nozzle configuration.

B - Scanned area 2160 CW to 2510. Scanning limited due to nozzle configuration and nozzles N6B.

C - Scanned area 2510 CW to 2850. Scanning limited due to nozzle configuration and nozzle N15B Jote - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume. S6-Supplement 6 volume. Weld I(

Attachment:

A24 Weld: NR02 4-566D (N4D)

Report Number: 1R23-121 Item Number: B3.90 Outage: 1 R23 (Fall 2010)

Coverage: 52.5%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 52.5% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

0

, v Oyster Creek' CD rD Feedwater o 60' S4 Exam Volume = 7.6 Sq. In.

60' S6 Exam Volume = 71.7 Sq. In.

600 S4 IRS-Scan LKCW achieved = 7.6 Sq. in.

600 S4 IRS-Scan LKCCW achieved = 7.6 Sq. In.

600 S6 P-Scan achieved = 26.0 Sq. In.

600 $4 T-Scan achieved = 7.6 Sq. In.

-- 600 S6 T-Scan achieved = 42.1 Sq. In.

/

//

/

/ I* 60°T/P 10.2" 060oP Radial Plate T Nom. =7.125" Clad T Nom. = 0.21875

f Reactor PressureVessel Coverage j CalculationSheet Oyster Creek N4D - Feed Water CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 79.3 IRS-Scan LKCW (S4) A 7.6 7.6 9.6% 360 2.4%

IRS-Scan LKCCW (S4) A 7.6 7.6 9.6% 360 2.4%

60" P-Scan (S6) A 71.7 26.0 32.8% 360 16.4%

600 T-Scan (S4) A 7.6 7.6 9.6% 360 4.8%

600 T-Scan (S6) A 71.7 42.1 53.1% 360 26.5%

(0 0

"16 % Total Composite Coverage = 52.5%

key 0 9/23/0(

Comments A - Scanned area 3600. Scanning limited due to nozzle configuration.

Note - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume, S6-Supplement 6 volume. Weld length in degrees

Attachment:

A25 Weld: NR02 2-566A (N5A)

Report Number: 5070 Item Number: B3.90 Outage: 1 R20 (Fall 2004)

Coverage: 29%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Automated / Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 29% code required coverage due to the nozzle configuration, proximity of the N13 and N14 nozzles, and the insulation support ring. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

Oyster Creek o -tF-IL N5A Ln 70* T-Scan Exam Volume - 26.29 Sq. In.

C+ *h45" T-Scan Exam Volume - 44.36 Sq. In.

60" T-Scan Exam Volume - 8.37 Sq. In.

'U 70" T-Scan achieved - 2.67 Sq. In.

45" T-Scan achieved - 22.61 Sq. In.

60" T-Scan achieved - 8.37 Sq, In.

C)

13 2&.25

/ 825 I --- .75 *

(U (0

60"T 01 4 *T o 1 60°T

)-6

Eyster Creek M 4Aitflp,ýN5A l<

Ln 70' P-Scan Exam Votume - 26.29 Sq. In I,

C- "45' P-Scan Exam Votume - 44.36 Sq. In to

() \70' P-Scan achieved - 2.31 Sq. In.

450 P-Scan achieved - 20.57 Sq. In.

rO

Tz-I-

13.05 iiI -2.75-1 45-P (0D (0

ICN t) o 45o

t Oyster Creek 1 tf N5A 60' T-Scan S6 Exam VoLume - 79.02 Sq, In.

60* T-Scan S6 achieved - 41.18 Sq. In.

CD)

-,a p

co M0 I

Oyster Creek LT"-+N5 A 60' T-Scan S4 Exam Volume - 8.37 Sq. In.

n 60" T-Scan S4 achieved - 8.37 Sq. In.

-3 ro

7 C)

-,a p

U0 (0

I

0 IOyster Creek ED il N5A 60* T-Scan S4 Exam Votume - 8.37 Sq. In.

60* T-Scan S4 achieved - 0.67 Sq. In.

LA CD

-3 (D

(0 NC

Olyster Creek S13 1124ii-F N5A I,<

(0 "3 60* T-Scan S6 Exam Volume - 79.02 Sq. In,

- 60' T-Scan S6 achieved - 28.39 Sq. In.

ro R)

/

p 4 (Di (U

0 t )

o *"K-IL

C) 6 00 06 E

> Q)

-Y E cii 0L) d x

£C u

(-)

dL d u u QLn

'%D %l C)

Page - of ?Z-Oyster Creek, 1R20

0 Oyster Creek

'L-P-&ý N5A LA~

60° P-Scan S6 Exam Votume - 79.02 Sq. In.

-3 60 P-Scan S6 achieved - 29.71 Sq, In, X-ICD I

IN

C)<z: <E n LV z z d

E--

0~ci -P-CF 0

0 c0 KL LA d R_. R

.53 00

-Cu

~JI OYSTER CREEK

ýGE 1ý OF. Z7-

G, C-N5A TL auto exam a~rea~

3020 2140 A Ni 3 A Ns5 A Insu~ti~ton suipport rin~g N5A 70TP a~uto exa~m (area.

I

C)

<T~ KU LF 0 z, 0

0 0 GJ)

0) C

(ýU CD m

0 0 0 -i3 0-I 0 ci 15 0

LF)

NlJ-C-

<1 LU) z

<E

0*

0 0) 0 x

0)

<E Co 0

4->

13 z--.-

I:5 dF <E 4

LP0 cc) z 0~)

C CD U.) mY 0

u C1 C) 0 :5 UO 0

4->

d

<F O0 ,

co O(U CREEK 4Z

3 McManual 60T (W 0 - 8.0")

P1, P2 EManual 60T (W 0 - 20.25")

P1, P2 per scan sheet 88" 301,80 214,80 N14 1 NI 3 A 352,8° 1

N5 A In N5A manucdexmorc exam area

0 0 Inspection Report No.: 005070 (n

(D Iso Condensor N5A C) Oyster Creek, 2004 0

CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 79.02 Area Sq. In. Auto Auto Auto Auto 700 T-Scan A 26.29 2.67 3.4% 88 0.4%

450 T-Scan A 44.36 22.61 28.6% 88 3.5%

600 T-Scan A 8.37 8.37 10.6% 88 1.3%

70* P-Scan A 26.29 2.06 2.6% 88 0.3%

450 P-Scan A 44.36 20.57 26.0% 88 3.2%

Inner 15%1" P-Scan A 8.37 8.37 10.6% 87 1.3%

(D 700 T-Scan 450 T-,3can o

600 T-Scan 700 P-Scan 450 P-Scan Inner 15%T"P-Scan 70°_T-Scan_

450 T-Scan 600 T-Scan 700 P-Scan 450 P-Scan Inner 15%T P-Scan

-o % Total Composite Coverage = 10%

Comments: A - Automated exams limited do to t.e proximity of the N13, N14 pads, the insulation support ring and the nozzle configuration.

Inner 15%T P-Scan area by modeling.

Note - Rounding methods may make calculated values appear in error.

C 0 0

Oyster Creek, Unit-1 (D ISO CONDENSOR N5A (D Fall 2004 2.

.ODE CROSS-SECTIONAL AREJ TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 88.8 Area Sq. In. Manual Manual Manual Manual 600 T-Scan S4 A 9.8 7.8 11.0% 96.0 1.5%/,_

600 T-Scan S6 A 79.0 36.8 41.4% 96.0 5.5%

IRS P-S3can S4 A 9.8 9.8 11.0% 96.0 1.5%

600 P-Scan $6 A 79.0 28.9 32.5% 96.0 4.3%

600 T-Scan S4 B 9.8 0.7 0.8% 63.0 0.1%

60' T-Scan S6 B 79.0 28.4 32.0% 63.0 2.8%

IRS P-Scan S4 B 9.8 9.8 11.0% 63.0 1.0%

60 P- B 79.0 28.9 32.5% 63.0 2.8%

600 T-ScXan S4 600 T-Scan S6 IRS P-Scan S4 600 P-1'can$6 600 T-Scan S4 600 T-sican S6 IRS P-Scan S4 60amP-crana6

'U % 1otal Composite Coverage = 19%/o Comments. A'" Scanning limited due to nozzle configuration.

B - Scanning limited due to the proximity of the N13 and N14 pads.

Note - Rounding methods may make calculated values appear in error.

Attachment:

A26 Weld: NR02 2-566A (N5A) Inner Radius Report Number: 5046 Item Number: B3.100 Outage: 1 R20 (Fall 2004)

Coverage: 78.9%

Base Metal and Weld Materials: Carbon Steel Nozzle Inner Radius Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Automated / Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 78.9% code required coverage due to the proximity of the N13 and N14 nozzles and the insulation support ring. The following sketches contain the limitations.

No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

Q C Oyster Creek Ej

~N5A M

LIA C+

Zone 1 Code required exam volume - 1,67 Sq. In.

Zone 2A Code required exam volume - 2.37 Sq. In.

R-)

C) Zone 1 Code exam volume achieved - 1.67 Sq. In, Zone 2A Code exam volume achieved - 2.37 Sq. In,

-U Z2A ODBRI p

(D Z2A ODBR Z1 PLATE 0

~t)

0 8 0-)

0? q-H CD CO d

x 0 09 0

0 115 ci-

<1 17

-0 N Ol

<1 4->

Li-z

.D

Jd 0

Cu 4->-

0~0 oc 0 c-0 N- +->

\ li H>c Ln 3L

E d

CC c5J K- C b

OC 0 S/ ci Nb

<ID L r'-

z/*

b cu 0--)

x <-F Cu b

0~

15

0. L_.

L-)

KI bJ

<::E LI z

'a

0 0 Report No.: 005046 a:

z Oyster Creek, Fall 2004 (n Weld N5A-IRS CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 100% Area % Auto Auto Auto Auto Auto CW A 100% 100% 100.0% 88 12.2%

Auto CCW A 100% 100% 100.0% 88 12.2%

% Total Composite Coverage = 24.4%

Manual CW B 100% 100% 100.0% 158.6 22.0%

Manual CCW B 100% 100% 100.0% 158.6 22.0%

% Total Composite Coverage = 44.1%

Manual CW C 100% 33% 33.0% 113.4 5.2%

Manual CCW C 100% 33% 33.0% 113.4 5.2%

% Total Composite Coverage = 10.4%

% Total Composite Coverage =

% Total Composite Coverage = 78.9%

(D

()D Comments: A - Examined accessible length automated Exam volume determined by modeling, 100% assigned volume.

B - Examined accessible length manually. Exam volume determined by modeling, 100% assigned volume. Plate and ODBR C - Examined accessible length manually. Exam volume determined by modeling, 33% assigned volume.

C - Manual scan from plate and ODBR surfaces. Coverage claimed for ODBR scans only due to insulation support ring interferences.

Note - Rounding methods may make calculated values appear in error.

Attachment:

A27 Weld: NR02 2-566B (N5B)

Report Number: 5071 Item Number: B3.90 Outage: 1 R20 (Fall 2004)

Coverage: 22%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Automated UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section Xl, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 22% code required coverage due to the nozzle configuration and the proximity of the insulation support ring. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

Oyster Creek ID tfi l N5B 1<

Ul 70° T-Scan Exam Volume - 26.29 Sq. In.

+ 450 T-Scan Exam Volume - 44,36 Sq. In.

(U 60° T-Scan Exam Volume - 8.37 Sq. In.

n to 70° T-Scan achieved - 2.67 Sq. In.

(U X" 45" T-Scan achieved - 22.61 Sq. In.

60° T-Scan achieved - 8.37 Sq. In.

R) 20.25 C)

/ 13.50

/

I - -8.25 t-/ 2.75 71 D PQ 601 I6T I I*-

O yster Creek n -t*I N5B c+ "70* P-Scan Exam Volume - 26.29 Sq. In.

C) 450 P-Scan Exam Volume - 44.36 Sq. In.

(U 70' P-Scan achieved - 2.06 Sq. In.

(45° P-Scan achieved - 20.57 Sq. In.

S"13.05

/ ~8.00, V!,

/

/ r17

-2.7 (0

(D -- 4i ,7 0 P 1+ 4 1o

(, 45*P

N5B TL auto exam area a

N5B

(

1720~ 70 I

165*

CD rJn restricted by insulation support ring tImAe M

0 N513 70TP axuto exa~m a~rea N lB

(-

m 1730 7 (-O-LO oJ 166" C,,

Area restricted by intsula~tion support ring rn o 3

K)

N513 45c* P1 aiuto exam area N5 B U

173° 70 k-D LID CIU 166" Area restricted~ intsulation support ring Dr CM7,

K.'

N5B P-Scan inn~er 15% auto exam area-N5 B

(-

Co 173,40 6.60 <0,,

LF)

OJ 1666" Areat restricted~ by insulation support ring Co

C 0 Inspection Report No.: 005071 o

Iso Condensor N5B CD 0

Oyster Creek, 2004 CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 79.02 Area Sq. In. Auto Auto Auto Auto 700 T-Scan 26.29 2.67 3.4% 194 0.9%

450 T-Scan 44.36 22.61 28.6% 195 7.7%

600 T-Scan 8.37 8.37 10.6% 195 2.9%

70' P-Scan 26.29 2.06 2.6% 194 0.7%

450 P-Scan 44.36 20.57 26.0% 194 7.0%

Inner 150/6%- P-Scan 8.37 8.37 10.6% 193.2 2.8%

"13 70* T-Scan 450 T-Scan 600 T-Scan 70' P-Scan 450 P-Scan Inner 15%r P-Scan 700 T-Scan 450 T-Scan 600 T-Scan 700 P-Scan 450 P-Scan Inner 15%T P-Scan

% Total Composite Coverage = 22%

0 Comments:

Inner 15%0" P-Scan area by modeling.

Note - Rounding methods may make calculated values appear in error.

Attachment:

A28 Weld: NR02 2-566B (N5B) Inner Radius Report Number: 5047 Item Number: B3.100 Outage: 1R20 (Fall 2004)

Coverage: 68.8%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Automated / Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 68.8% code required coverage due to the proximity of the insulation support ring. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

.Oyster Creek C lk- N5B Zone 1 Code required exam votume - 1.67 Sq. In, Zone 2A Code required exam volume - 2,37 Sq. I 1.

Zone 1 Code exam volume achieved - 1.67 Sq. In, rnZone 2A Code exam votume achieved - 2.37 Sq. Ii1.

iii * -- 13.35 Z2A ODBR (0p - Z2A PLATE ID Z2A PLATE

,' Z2A ODBR Zi PLATE 0 ZI PLATE 0b It _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

C3) C5 ci)

E

-H 0 6 15 x

6_

L._ (1) 15 0

LI §1 0

_t_>

6

,15 pq LZ (Y) H z7 C)

OYSTER CREEK PAGE Lý OF. /5

C)) \6 o C* *_

Aj--P d mo Lf4' d 0 x 0 Cu p-4->

00 OYSTER CREEK PAGE ') OFJ

,15

CD E L.

K TjX

._0

§-

ksD L) m Lf-

©N oJ H-OYSTER CREEK PAGE OF /5

b

/1 o x mm 4F->

L-d z _

-0

+CU d N p-.q mLP-OYSTER CREEK AGE '0OF /

Report No.: 005047 (D

z 013

_L Oyster Creek, Fall 2004

E)

Weld N5B-IRS CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 100% Area % Auto Auto Auto Auto Auto CW A 100% 100% 100.0% 192.2 26.7%

Auto CCW A 100% 100% 100.0% 192.2 26.7%

% Total Composite Coverage = 53.4%

Manual CW B 100% 33% 33.0% 167.8 7.7%

Manual CCW B 100% 33% 33.0% 167.8 7.7%

% Total Composite Coverage = 15.4%

% Total Composite Coverage =

_0 % Total Composite Coverage = 68.8%

0 Comments: A - Examined accessible length automated Exam volume determined by modeling, 100% assigned volume.

B - Examined accessible length manually. Exam volume determined by modeling, 33% assigned volume.

B - Manual scan from plate and ODBR surfaces. Coverage claimed for ODBR scans only due to insulation support ring interferences.

Note - Rounding methods may make calculated values appear in error.

Attachment:

A29 Weld: NR02 2-567A (N6A)

Report Number: 1R23-115 Item Number: B3.90 Outage: 1R23 (Fall 2010)

Coverage: 28.1%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 28.1% code required coverage due to the nozzle configuration, proximity of the N13B instrument nozzle and nozzle window (bio-shield) access limitations. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

0 (0

(A Oyster Creek" (DJ Core Spray 0l I.

600 S4 Exam Volume = 7.4 Sq. In.

600 S6 Exam Volume = 58.9 Sq. In.

600 S4 IRS-Scan LKCW achieved = 7.4 Sq. In.

600 54 IRS-Scan LKCCW achieved = 7.4 Sq. In.

600 S6 P-Scan achieved = 30.5 Sq. In.

600 S4 T-Scan achieved = 7.4 Sq. In.

600 S6 T-Scan achieved = 39.5 Sq. In.

60°T/P I 11.5" 60 0 P 19.6"

// 60 0 T

~~~1 (D

0 Radial Plate T Nom. = 7.125" Clad T Nom. = 0.21875"

97-N13B N4A N14B N6A 1800 LO (D

0

O IHITACHI Reactor PressureVessel Coverage CalculationSheet Oyster Creek N6A - Core Spray CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 66.3 IRS-Scan LKCW (S4) A 7.4 7.4 11.2% 158 1.2%

IRS-Scan LKCCW ISM4 A 7.4 7.4 11.2% 158 1.2%

600 P-Scan (S61 A 58.9 30.5 46.0% 158 10.1%

60' T-Scan IS41 A 7.4 7.4 11.2% 158 2.4%

60° T-Scan $S61 A 58.9 39.5 59.6% 158 13.1%

t0

% Total Composite Coverage = 28.1%

Ray0 91'2 :5 Comments A- Scanned area from 1 inch CW of nozzle N13B CW to 180l Scanning limited due to nozzle configuration, proximity of the N13B and the N6A nozzle window configuration. Examined from the N4A nozzle window Note - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume. S6-Supplement 6 volume. Weld length indegreeE

Attachment:

A30 Weld: NR02 2-567A (N6A)

Report Number: 1 R23-115 Item Number: B3.100 Outage: 1 R23 (Fall 2010)

Coverage: 44%

Base Metal and Weld Materials: Carbon Steel Nozzle Inner Radius Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 44% code required coverage due to the nozzle configuration, proximity of the N13B Instrument nozzle, and nozzle window (bio-shield) access limitations. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

0 Oyster Creek C)

(D Core Spray 0 600 S4 Exam Volume = 7.4 Sq. In.

600 S6 Exam Volume = 58.9 Sq. In.

600 S4 IRS-Scan LKCW achieved = 7.4 Sq. In.

60° S4 IRS-Scan LKCCW achieved = 7.4 Sq. In.

600 S6 P-Scan achieved = 30.5 Sq. In.

600 54 T-Scan achieved = 7.4 Sq. In.

600 S6 T-Scan achieved = 39.5 Sq. In.

60°T/P I 11.5" 60 0 P 19.6"

/~ I 60 0T

~~~1 0

(0 Radial Plate T Nom. = 7.125" Clad T Nom. = 0.21875"

N13B N4A N14B N6A 1800

_0

Attachment:

A31 Weld: NR02 2-567B (N6B)

Report Number: OC1R22-124 Item Number: B3.90 Outage: 1R22 (Fall 2008)

Coverage: 61.7%

Base Metal and Weld Materials: Carbon Steel Nozzle Inner Radius Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 61.7% code required coverage due to the nozzle configuration, proximity of the N15B and N16B Instrument nozzles, and the N4C feedwater nozzle. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

Oyster CreeK Core Spray 600 S4 Exam Volume = 7.6 Sq. In.

600 S6 Exam Volume = 60.6 Sq. In.

600 S4 IRS-Scan LKCW achieved = 7.6 Sq. In.

600 S4 IRS-Scan LKCCW achieved = 7.6 Sq. In.

600 S6 P-Scan achieved = 31.0 Sq. In.

600 S4 T-Scan achieved = 7.6 Sq. In.

600 S6 T-Scan achieved = 38.0 Sq. In.

/

29~P-8i~ew 11.2" 16.2" 600T/P 60 0 P 600 T

1 Radial Plate T Nom. = 7.125" Clad T Nom. = 0.21875"

LC)

('0 600 T-scan Manual UT examinations restricted due to the proximity of N4A feedwater nozzle Restricted Area 0n M*

110' Az.

572

Vý ,

HITACHI Reactor PressureVessel Coverage CalculationSheet Oyster Creek N6'Aj Core Spray CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 68.2 IRS-Scan LKCW (S41 A 7T6 7.6 11.1% 360 2.8%

IRS-Scan LKCCW (S4) A 7.6 7.6 11.1% 360 2.8%

600 P-Scan (S6) A 60.6 31.0 45.5% 360 22.7%

60* T-Scan (S41 A 7.6 7.6 11.1% 360 5.6%

600 T-Scan ($61 A 60.6 38.0 55.7% 360 27.9%

____ _I____I __ _

%Total Composite Coverage = b1./7 Rev. 0 9/23/0O Comments A - Scanned area 3600. Scanning limited due to nozzle configuration.

Note - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume, S6-Suppiement 6 volume, Weld length in dewrees,

Attachment:

A32 Weld: NR02 2-567B (N6B)

Report Number: OC1R22-123 Item Number: B3.100 Outage: 1R22 (Fall 2008)

Coverage: 60.9%

Base Metal and Weld Materials: Carbon Steel Nozzle Inner Radius Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 60.9% code required coverage due to the nozzle configuration, proximity of the N15B and N16B Instrument nozzles. The following sketches contain the limitations. No unacceptable indications were noted. A system pressure test was also completed with no unacceptable indications observed.

N 168B N15B if) 0 0 Iu4 4 7 *A z. 29 4 *A .

241" A . 30*Az. N F

I--rnManual MM, UT exams restricted due to to the proximity of N15B and N16B nozzles.

1 1 -5721

HITACHI Reactor PressureVessel Coverage CalculationSheet Oyster Creek N6B - Core Spray CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume = 68.2 IRS-Scan LKCW (S4) A 7.6 7.6 11.1% 360 2.8%

IRS-Scan LKCCW (S4) A 7.6 7.6 11.1% 360 2.8%

600 P-Scan (56) A 60.6 31.0 45.5% 347 21.9%

600 T-Scon (S41 A 7.6 7.6 11.1% 360 5.6%

600 T-Scan (S6) A 60.6 38.0 55.7% 360 27.9%

% Total Composite Coverage = 60.9%

Rev.O 9/23/04 Comments A - Scanned area 360°. Scanning limited due to nozzle configuration.

N - R6 Note - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume, S6-Supplement 6 volume. Weld length in degrees.

Attachment:

A33 Weld: NR02 1-576 (N7A) Closure Head Nozzle Report Number: OCR20-076 Item Number: B3.90 Outage: 1 R20 (Fall 2004)

Coverage: 76%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Nozzle / Head OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PD1 program.

Limitation

Description:

The completed examination was limited to 76% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

3 3

ý6 Oyster Creek, Unit-1 N7A Closure Head Nozzle Fall 2004 CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 68.7 Area Sq. In. Manual Manual Manual Manual 600 T-Scan S4 A 9.8 9.8 14.3% 180.0 3.6%

600 T-Scan S6 A 58.9 36.8 53.6% 180.0 13.4%

IRS P-Scan 34 A 9.8 9.8 14.3% 180.0 3.6%

600 P-Scan S6 A 58.9 28.3 41.2% 180.0 10.3%

Exam Volume = 59.1 600 T-Scan S4 B 6.4 6.4 10.8% 180.0 2.7%

60° T-Scan S6 B 52.7 47.5 80.4% 180.0 20.1%

IRS P-Scan 34 B 6.4 6.4 10.8% 180.0 2.7%

60° P-Scan $6 B 52.7 46.0 77.8% 180.0 19.5%

600 T-Scan S4 600 T-Scan S6 IRS P-Scan :34 600 P-Scan S6 608 T-Scan S4 600 T-Scan $6 IRS P-Scan :34 600 P-Scan $6

% i otal Composite Coverage = I t)"/o Comments: A - Top side of offset nozzle. Examined 1800 length. Scanning limited due to nozzle configuration.

B - Bottom side of offset nozzle. Examined 1800 length. Scanning limited due to nozzle configuration.

Weld length in degrees. IRS examination coverage determined by modeling.

Coverage sheet modified for offset nozzle configurations.

Note - Rounding methods may make calculated values appear in error.

0 160*

Oyster Creek Unit-1 N7A Bottom Side Coverage I .6" wei 60* NS Exam Volume = 14.9 Sq. In.

60" FV S6 Exam Volume = 37.8 Sq. In.

60" FV S4 / 15%T IRS Exam Volume = 6.4 Sq. In.

7.8 ATr N8 T.0 "J 801P Ks 60" NS T-Scan achieved = 10.2 Sq. In.

60° FV S6 T-Scan achieved = 37.3 Sq. In.

60' FV S4 T-Scan achieved = 6.4 Sq. In.

60° FV P-Scan achieved = 9.8 Sq. In, 60" FV 56 P-Scan achieved = 36.2 Sq. In.

Inner 15%T IRS-Scan achieved = 6.4 Sq. In. (By modeling.)

0) TIP Nominal T = 5 - 5/16" Nominal Clad T = 7/32" 80TP NS 6(TNS II. P el-p Top Side Coverage 60' NS Exam Volume = 17.3 Sq. In.

60° FV S6 Exam Volume = 41.6 Sq. In.

60° FV S4 / 15%T IRS Exam Volume = 9.8 Sq. In.

20.r" 60* NF$T-Scan =

acrhieved 3.8lSo. In.

60" FV S6 T-Scan achieved = 31.8 Sq. In.

60' FV S4 T-Scan achieved = 9.8 Sq.In.

60° FV P-Scan achieved = 4.6 Sq. In. I 60I FV S6 P-Scan achieved = 23.7 Sq. In.

Inner 15%T IRS-Scan achieved = 9.8 Sq. In. (By modeling.)

Oyster Creek Unit-I, 2004 Page :2 Of R

Attachment:

A34 Weld: NR02 1-576 (N7A) Closure Head Nozzle Inner Radius Report Number: OCR20-114 Item Number: B3.100 Outage: 1 R20 (Fall 2004)

Coverage: 74%

Base Metal and Weld Materials: Carbon Steel Nozzle Inner Radius Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Nozzle / Head OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 74% code required coverage due to the offset nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

0)140 Oyster Creek Unit-1 N7A Bottom Side Coverage 11W.

60° NS Exam Volume = 14.9 Sq. In.

60* FV S6 Exam Volume z 37.8 Sq. In.

60" FV S4 / 15%T IRS Exam Volume = 6.4 Sq. In.

7.-

OTTNS YB-

,-, WP No 60" NS T-Scan achieved = 10.2 Sq. In.

60" FV S6 T-Scan achieved = 37.3 Sq. In.

60" FV S4 T-Scan achieved = 6.4 Sq. In.

C 60* FV P-Scan achieved = 9.8 Sq. In.

60" FV S6 P-Scan achieved = 36.2 Sq. In.

Inner 15%T IRS-Scan achieved = 6.4 Sq. In. (By modeling.)

S..

Ž1 Nominal T = 5 - 5/16" Nominal Clad T = 7/32" 11.1"

S.r 509 Top Side Coverage 60' NS Exam Volume = 17.3 Sq. In.

60" FV S6 Exam Volume = 41.6 Sq. In.

60' FV S4 / 15%T IRS Exam Volume = 9.8 Sq. In.

6'0 NMT-.Sn *hi*av*'d = 5.0 Sq. In. I n.W-60" FV S6 T-Scan achieved = 31.8 Sq. In.

60° FV S4 T-Scan achieved = 9.8 Sq. In.

60" FV P-Scan achieved = 4.6 Sq. In.

60" FV S6 P-Scan achieved = 23.7 Sq. In.

Inner 15%T IRS-Scan achieved = 9.8 Sq. In. (By modeling.)

Oyster Creek Unit-I, 2004 Page ~~:2~.oOf A4

C C--

Oyster Creek, Unit-1 N7A Closure Head Nozzle Fall 2004 CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 100. Area in %. Manual Manual Manual Manual IRS CW =A 100 74 74.0% 360 37.0%

IRsccw A 100 74 74.0% 360 37.0%

IRS CW I IRSCCW IRS CW IRSCCW IRS CW IRSCCW IRSc I I IRSCCW IRS CW IRSCCW IRS CW IRSCCW

% Total Composite Coverage = 74%

Comments: A - Examination limited due to offset nozzle configuration.

Weld length in degrees. IRS examination coverage determined by modeling.

Note - Rounding methods may make calculated values appear in error.

Attachment:

A35 Weld: NR02 3-576 (N7B) Closure Head Nozzle Report Number: OCR20-075 Item Number: B3.90 Outage: 1 R20 (Fall 2004)

Coverage: 78%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Nozzle / Head OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 78% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

0 Oyster Creek Unit-1 (D

W N7B (D)

Bottom Side Coverage C

60° NS Exam Volume = 10.6 Sq. In.

0-' 60' FV S6 Exam Volume = 25.2 Sq. In.

07 60a FV S4 / 15%T IRS Exam Volume = 4.6 Sq. In.

K 15.4' 60" NS T-Scan achieved = 6.1 Sq. In.

60° FV S6 T-Scan achieved = 24.9 Sq. In.

r-'T 60° FV S4 T-Scan achieved = 4.6 Sq. In.

104.

60"P 6.7' 60° NS P-Scan achieved = 5.7 Sq. In.

5.9. 60" FV S6 P-Scan achieved = 23.9 Sq. In.

WOPNS Inner 15%T IRS-Scan achieved = 4.6 Sq. In. (By modeling.)

60*.&

7.rw

'I s 8.0*

I1.7" 60.P I

16.81 Top Side Coverage Q0 60" NS Exam Volume = 11.9 Sq. In.

CD 60' FV S6 Exam Volume = 29.5 Sq. In.

600 FV S4 115%T IRS Exam Volume = 6.8 Sq. In.

60° NS T-Scan achieved = 3.9 Sq. In.

60° FV S6 T-Scan achieved = 26.4 :3q. In.

0 60° FV S4 T-Scan achieved = 6.8 Sq. In.

J 60' NS P-Scan achieved = 3.5 Sq. In.

60° FV S6 P-Scan achieved = 19.9 Sq. In. Nominal T = 5 - 5/16" Inner 15%T IRS-Scan achieved = 6 8 Sq. In. (By modeling.) Nominal Clad T = 7/32" N

ý3 3 Oyster Creek, Unit-1 N7B Closure Head Nozzle Fall 2004 CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 48.2 Area Sq. In. Manual Manual Manual Manual 600 T-Scan ;4 A 6.8 6.8 14.1% 180.0 3.5%

60* T-Scan S6 A 41.4 30.3 62.9% 180.0 15.7%

IRS P-Scan S4 A 6.8 6.8 14.1% 180.0 3.5%

600 P-Scan S6 A 41.4 23.4 48.5% 180.0 12.1%

Exam VolIme = 40.4 60* T-Scan 84 B 4.6 4.6 11.4% 180.0 2.8%

60° T-Scan S6 B 35.8 31.0 76.7% 180.0 19.2%

IRS P-Scan ,S4 B 4.6 4.6 11.4% 180.0 2.8%

600 P-Scan $6 B 35.8 29.6 73.3% 180.0 18.3%

600 T-Scan 84 600 T-Scan S6 IRS P-Scan.134 600 P-Scan S6 60° T-Scan S4 60° T-Scan S6 IRS P-Scan S4 600 P-Scan 86

% Total Composite Coverage = 78%

Comments: A - Top side of offset nozzle. Examined 1800 length. Scanning limited due to nozzle configuration.

B - Bottom side of offset nozzle. Examined 1800 length. Scanning limited due to nozzle configuration.

Weld length in degrees. IRS examination coverage determined by modeling.

Coverage sheet modified for offset nozzle configurations.

Note - Rounding methods may make calculated values appear in error.

Attachment:

A36 Weld: NR02 3-576 (N7B) Closure Head Nozzle Inner Radius Report Number: OCR20-115 Item Number: B3.100 Outage: 1 R20 (Fall 2004)

Coverage: 88%

Base Metal and Weld Materials: Carbon Steel Nozzle Inner Radius Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 88% code required coverage due to the offset nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

3 0 Oyster Creek Unit-1 CA N7B Bottom Side Coverage C-) 60° NS Exam Volume = 10.6 Sq. In.

60* FV S6 Exam Volume = 25.2 Sq. In.

C) 60" FV S4 / 15%T IRS Exam Volume = 4.6 Sq. In.

-P 60° NS T-Scan achieved = 6.1 Sq. In.

1,0.4 60° FV S6 T-Scan achieved = 24.9 Sq. In.

60' FV S4 T-Scan achieved = 4.6 Sq. In.

10 4' GTP 679 60' NS P-Scan achieved = 5.7 Sq. In.

T 9", 60° FV S6 P-Scan achieved = 23.9 Sq. In.

Inner 15%T IRS-Scan achieved = 4.6 Sq. In. (By modeling.)

I 7.Ž1 K6ITNS Ur 11.1' I

16 8*

"13 Top Side Coverage (a 60° NS Exam Volume = 11.9 Sq. In.

( 60' FV S6 Exam Volume = 29.5 Sq. In.

600 FV S41 15%T IRS Exam Volume = 6.8 Sq. In.

600 NS T-Scan achieved = 3.9 Sq. H.

60' FV S6 T-Scan achieved = 26.4 3q. In.

o 60' FV S4 T-Scan achieved = 6.8 S I. In.

\J-- 60° NS P-Scan achieved = 3.5 Sq. In.

60° FV S6 P-Scan achieved = 19.9 Sq. In. Nominal T = 5 - 5/16" Inner 15%T IRS-Scan achieved = 6 8 Sq. In. (By modeling.) Nominal Clad T = 7/32" N

ACp%

Oyster Creek, Unit-1 N7B Closure Head Nozzle Fall 2004 CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 100. Area in %. Manual Manual Manual Manual IRS CW =A 100 88 88.0% 360 44.0%

IRSCCW A 100 88 88.0% 360 44.0%

IRS CW I IRSCCW IRS CW I IRSCCW IRS CW I IRSCCW IRS CW I IRSCCW IRS CW I IRSCCW IRS CW I IRSCCW

% Total Composite Coverage = 88%

Comments: A - Examination limited due to offset nozzle configuration.

Weld length in degrees. IRS examination coverage determined by modeling.

Note - Rounding methods may make calculated values appear in error.

Attachment:

A37 Weld: NR02 5-576 (N8) Closure Head Nozzle Report Number: 1 R21-166 Item Number: B3.90 Outage: 1 R21 (Fall 2006)

Coverage: 89%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 89% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

Oyster Creek Unit-1 N8 60: NS Exam Volume = 6 9 Sq. In.

60' FV S6 Exam Volume = 19 8 Sq. In 60° FV S4 / 15%T IRS Exam Volume = 4.2 Sq. In.

Nominal T and dlad from CE D.g. 232-574 Segments speficaon = 5 - 5116' Nozzle details from CE Dwg. 232-576 Nominal T = 5 - 5/16" Nominal Clad T =7 1 32"

0 Oyster Creek 01R21 N8 Closure Head Nozzle 0

Fall 2006 CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Percent Weld Length = 360. Required Exam Area Scanned of Area Weld Length Percent Exam Volume = 30.9 Area Sq. In. Manual Manual Manual Manual 600 T-Scan S4 A 4.2 4.2 13.6% 360.0 6.8%

608 T-Scan S6 A 26.7 23.8 77.0% 360.0 38.5%

IRS P-Scan S4 A 4.2 4.2 13.6% 360.0 6.8%

600 P-Scan S6 A 26.7 23 1 74.8% 360.0 37.4%

600 T-Scan S4 600 T-Scan S6 IRS P-Scan S4 60_ P-ScanS6S6 60° T-Scan S4 60' T-Scan S6 IRS P-Scan S4 600 P-Scan S6 60° T-Scan S4 _

60* T-Scan S6 IRS P-Scan S4 600 P-Scan_6

% Total Composite Coverage = 89%

Comments: A - Examined 360' length. Scanning limited due to nozzle configuration.

Weld length in degrees. IRS examination coverage determined by modehng.

Note - Rounding methods may make calculated values appear in error.

Z0.

Attachment:

A38 Weld: NR02 6-567 (N9) CRD Return Nozzle Report Number: OC1 R22-143 Item Number: B3.90 Outage: 1R22 (Fall 2008)

Coverage: 69%

Base Metal and Weld Materials: Carbon Steel Nozzle Examination Volume: Coverage per figure IWB-2500-7, "Nozzle in Shell or Head" UT Exam Type: Manual UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section XI, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 69% code required coverage due to the nozzle configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

0 (D Oyster Cree '

CRDH Nozzle C) 600 S4 Exam Volume = 7.2 Sq. In.

600 S6 Exam Volume = 49.2 Sq. In.

600 S4 IRS-Scon LKCW achieved = 7.2 Sq. In.

600 S4 IRS-Scan LKCCW achieved = 7.2 Sq. In.

600 S6 P-Scan achieved = 33.0 Sq. In.

600 S4 T-Scan achieved = 7.2 Sq. In.

60 S6 T-Scan achieved = 36.3 Sq. In.

23~ S..~

12.2" 16.3" 60°T/P 60 0P 60 0T I I 7 I 3 Places

-- ~-1 L4 C'b 1-a Radial Plate T Nom. = 7.125" rkdrTKturn -fl 'ý.~;

Attachment:

A39 Weld: NR02 5-567 (N9) CRD Return Nozzle Safe End Report Number: 1 R24-131 Item Number: B5.10 Outage: 1 R24 (Fall 2012)

Coverage: 67.4%

Base Metal and Weld Materials: Carbon Steel Nozzle to Stainless Steel Safe End Examination Volume: Coverage per figure IWB-2500-8, "Similar and Dissimilar Metal Weld in Components, Nozzles, and Piping" UT Exam Type: Manual UT Scanning from Nozzle OD Surface Performed per the requirements of ASME Code, Section Xl, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 67.4% code required coverage due to OD safe end configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

Report No.

Site: Oyster Creek Unit: 1 Project: 01R24 HITACHI 1R24-131 System: CRDR 4th Interval/3rd Period Component No: NR02 5-567

Description:

N9 CRDR NOZZLE SAFE END Page 9of It

Station: Oyster Creek UT Volumetric Coverage U1 HITACHI Calculation Form Component Number:

Report Number: 1 NR02 5-567 1R24-131 Date: 11/11/2012 Coverage Calculations Weld Inpoection Data Configuration: Noz to SE Weld Type Dual Access Diameter(Nom): I Limitation Type Confia System 225 "tY@ Weld C/L 0.650 Examination Box length 1.200 Weld length (Actual) 15,501 Loss Volume Data. Tne rnaci.of:ý tinrrarcns Lie. tn",c. uttiocurie to CC) a.~.t-p.4rs noop ,;.rnflz.O LraOOmeor

-zrruic CD p-.,

conrlgurai;.n Thrus resuuiting in 'rig nt srict triang ic or IeCtar~gid bnOýPeS o;lsis coveiag e Tnus~ co~frnofl gesometric ýhapes millbe usea for determininlg volunras th~athave, not been cxamnlnso..

Code Required Volume 4.0 cubic inches Insert "1" for each uuwnn1;IiU vuMuWium~ýR uuu. Lu.uniuon ixiu All

!LK-enu].IimnuniutIne ae t n LIU Data Sht # Axial Scan Identifier Scan Length Demnh Mtm WedLenut Loss Volume 0 affected Lenath 45 SW Dnstream 0.8 0.22 1 15.50 2.73 45 SW Upstream 0.5 0.22 1 15.50 1.71 60 RL Dnstream 0.35 0.22 1 15.50 1.19 60 RL Upstream 0.9 0.22 1 15.50 3.07 45 RL Dnstream 0.8 0.22 1 15.50 2.73 45 RL Upstream 0.5 0.22 1 15.50 1.71 0 0.22 0 15.50 0.00 0 0.22 0 15.50 0.00 0 0.22 0 15.50 0.00 0 0.22 0 15.50 0.00 0 0.22 0 15.50 0.00 0 0.22 0 15.50 0.00 Clrc Scan Identifier Lenoth Deoth Multiplier* Weld Length Comments Loss Volume 30 SW Clockwise 0 o0.00 0.00 0.00 30 SW Counter Clockwise 0 0.00 0 0.00 0.00 38 RL Upstream 0 0.00 0 0.00 0.00 38 RL Dnstream 0 0.00 0 0.00 0.00 0 0.22 0 15.50 0.00 0 0.22 0 15.50 0.00 0 0.22 0 15.50 0.00 0 0.22 0 15.50 0.00 Total Number of scans 10 Total Aggregate Volume iu. Total Aggregate Volume of Loss Coverage in cubic inches in cubic inches Resultant loss coverage in % 32.58% Select which coverage applies Examination Coverageobtained 67.42% 1 X ASME Code Coverage GEH Procedure Coverage Page p°of II Prepared Customer Reviewed By:

Date: I1 If- Date:

Attachment:

A40 Weld: NR02 4-565D (N1 D)

Report Number: 5123 Item Number: 65.10 Outage: 1 R20 (Fall 2004)

Coverage: 70%

Base Metal and Weld Materials: Carbon Steel Nozzle to Stainless Steel Safe End Examination Volume: Coverage per figure IWB-2500-8, "Similar and Dissimilar Metal Weld in Components, Nozzles, and Piping" UT Exam Type: Automated UT Scanning from Vessel OD Surface Performed per the requirements of ASME Code,Section XI, Appendix VIII:

Yes, the examination was performed to requirements contained in ASME Section X1, Appendix VIII per the PDI program.

Limitation

Description:

The completed examination was limited to 70% code required coverage due to the nozzle OD configuration. The following sketches contain the limitations. No unacceptable indications were noted.

A system pressure test was also completed with no unacceptable indications observed.

0 LU Oyster Creekp (D

Recirc Outlet 00 600 S4 Exam Volume = 9.5 Sq. In.

600 S6 Exam Volume = 66.4 Sq. In.

600 S4 IRS-Scan LKCW achieved = 9.5 Sq. In.

60* S4 IRS-Scan LKCCW achieved = 9.5 Sq. In.

600 S6 P-Scan achieved = 13.5 Sq. In.

600 S4 T-Scan achieved = 4.0 Sq. In.

600 S6 T-Scan achieved = 36.1 Sq. In.

/

/ 7.1" 16.7"

/ 600T/P 60°P 60 0 T I I I Radial Plate T Nom. 7.125" I oý b 01 Clad T Nom. = 0..21875"

Wall Thickness Profile Sheet Component ID Number: NR02 4.-65D INIDJ 1.5"

-I 1.5" I M3 Crown Height: EL~US Crown Width: /.x NOZZLE SAFE-END UPST Component: DNST Component:

Nominal Diameter:

Weld Length: HEQ 600 RL 600 RL 450 RL 450 RL 450 S 450 S 450S, 45°RL, 80-RL Supplement 10 Examination Coverage Thickness Taken from 1996 Data

,IA ý011ý0, ANII Kiý ý,,

0 GE Nuclear Energy Non-Machined Area NR02 4-565D (N1D) NOZZLE to SAFE-END JPG k.-_ Vje~rmt- ile[DCOI .

NI 46. .

SUMMARY

NUMBER: 005123 PAGE 19 of 12

Request for Relief (R-45) for Obtaining the Required Percentages During the Fourth Interval for Class 1 and Class 2 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 1 of 6) 1.0 ASME CODE COMPONENTS AFFECTED Code Class: 1 and 2

Reference:

Table IWB-2500-1 Table IWC-2500-1 Examination Category: B-J, B-M-1, C-B, C-F-l, C-F-2 Item Number: B9.11, B12.40, C5.81, C9.11, C2.21, C5.11

Description:

Limited Code Coverage on Piping Weld Examinations Component Number: See Table R-45 2.0 APPLICABLE CODE EDITION AND ADDENDA The fourth 10-year Inservice Inspection (ISI) interval program was based on the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel (B&PV)

Code,Section XI, 1995 Edition with 1996 Addenda.

3.0 APPLICABLE CODE REQUIREMENT ASME Section Xl, 1995 Edition with 1996 Addenda, required 100% volumetric examination of Class 1 and 2 welds as defined by Table IWB-2500-1 and Table IWC-2500-1.

4.0 IMPRACTICALITY OF COMPLIANCE Pursuant to 10 CFR 50.55a(g)(5)(iii), relief is requested from the 100% volumetric examination requirements of Class 1 and 2 welds as defined by Table IWB-2500-1 and Table IWC-2500-1 for the welds specified in Table R-45, "Limited Weld Coverage," on the basis that conformance with these Code requirements is impractical due to component configuration and access restrictions.

Request for Relief (R-45) for Obtaining the Required Percentages During the Fourth Interval for Class 1 and 2 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 2 of 6)

Table R Limited Weld Coverage Weld Description Coverage Item Figure Notes NQ-2-0215 Weld - Branch to Pipe 25% C5.81 1 Examined from Pipe side only due to Pipe Branch Configuration NE-5-0002 Safe End to Elbow 50% B9.11 2 Examined from Elbow side only due to SE Taper NE-5-0022A Safe End to Elbow 50% B9.11 3 Examined from Elbow side only due to SE Taper NG-D-0002 Elbow to Pipe 50% B9.11 4 Examined from Pipe side only due to Elbow Taper NE-2-0061 Pipe to Valve V-14-0167 50% B9.11 5 Examined from Pipe side only due to Valve Configuration NE-2-0256 Pipe to Valve V-14-0037 50% B9.1 1 6 Examined from Pipe side only due to Valve Configuration NE-2-0255 V-14-0036 to Pipe 50% B9.11 7 Examined from Pipe side only due to Valve Configuration NE-2-0257 V-14-0037 to Pipe 50% B9.1 1 8 Examined from Pipe side only due to Valve Configuration NE-2-220 Valve to Pipe 50% B9.1 1 9 Examined from Pipe side only due to Valve Configuration NE-2-240 Valve to Pipe 50% B9.11 10 Examined from Pipe side only due to Valve Configuration NE-5-206 Valve to Pipe 50% B9.11 11 Examined from Pipe side only due to Valve Configuration NE-5-214 Valve to Pipe 50% B9.11 12 Examined from Pipe side only due to Valve Configuration NU-1-0001 Valve to Pipe 50% B9.11 13 Examined from Pipe side only due to Valve Configuration ND-10-0005 Pipe to Valve V-16-0063 50% B9.11 14 Examined from Pipe side only due to Valve Configuration ND-10-0009 Pipe to Valve 50% B9.11 15 Examined from Pipe side only due to Valve Configuration NG-A-0007 Valve to Elbow 50% B9.11 16 Examined from Elbow side only due to Valve Configuration NG-A-0006 Elbow to Valve 50% B9.11 17 Examined from Pipe side only due to Valve Configuration NG-A-0014 Elbow to Pump 50% B9.11 18 Examined from Elbow side only due to Pump Configuration NG-A-0018 Elbow to Valve 50% B9.11 19 Examined from Elbow side only due to Valve Configuration NG-B-0006 Valve to Elbow 50% B9.11 20 Examined from Elbow side only due to Valve Configuration NG-B-0012 Pump to Elbow 50% B9.11 21 Examined from Elbow side only due to Pump Configuration NG-B-0005 Pipe to Valve V-37-20 50% B9.11 22 Examined from Pipe side only due to Valve Configuration NG-B-0016 Elbow to Valve 50% B9.11 23 Examined from Elbow side only due to Valve Configuration NG-C-0005 Valve to Elbow 50% B9.11 24 Examined from Elbow side only due to Valve Configuration NG-C-0012 Pump to Elbow 50% B9.11 25 Examined from Elbow side only due to Pump Configuration

Request for Relief (R-45) for Obtaining the Required Percentages During the Fourth Interval for Class 1 and 2 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 3 of 6)

Table R Limited Weld Coverage Weld Description Coverage Item Figure Notes NG-C-001 6 Elbow to Valve 50% B9.11 26 Examined from Elbow side only due to Valve Configuration NG-C-0004 Pipe to Valve 50% B9.11 27 Examined from Pipe side only due to Valve Configuration ND-10-0020 Valve V-16-0061 to Pipe 50% B9.11 28 Examined from Pipe side only due to Valve Configuration 29 Deleted ND-1-0029 Elbow to Valve 50% B9.11 30 Examined from Elbow side only due to Valve Configuration 31 Deleted NE-2-0124 Pipe to Valve V-14-0170 50% B9.1 1 32 Examined from Pipe side only due to Valve Configuration NE-2-0254 Pipe to Valve V-14-36 50% B9.11 33 Examined from Pipe side only due to Valve Configuration 34 Deleted NU-4-0002 Tee to Valve 50% B9.11 35 Examined from Tee side only due to Valve Configuration NG-B-0017 Valve to Pipe 50% B9.11 36 Examined from Pipe side only due to Valve Configuration NG-A-0019 Valve to Pipe 50% B9.11 37 Examined from Pipe side only due to Valve Configuration ND-1-0209 Valve V-16-0001 to Pipe 50% B9.11 38 Examined from Pipe side only due to Valve Configuration ND-1-0208 Elbow to Valve 50% B9.11 39 Examined from Elbow side only due to Valve Configuration MV-5-001 Flange to Tee 50% B9.11 40 Examined from Tee side only due to Flange Taper Configuration ND-10-0008 Valve to Elbow 50% B9.11 42 Examined from Elbow side only due to Valve Configuration NG-D-0004 Pipe to Valve 50% B9.11 43 Examined from Pipe side only due to Valve Configuration NG-D-0005 Valve to Pipe 50% B9.11 44 Examined from Pipe side only due to Valve Configuration NG-D- Pump to Elbow WOL 52% B9.11 45 Examined from Elbow side only due to Overlay and Pump Configuration 0011 R1 NG-D-0015 Elbow to Valve 75% B9.11 46 Examined from Elbow side only due to Valve Configuration NG-D-0016 Valve to Pipe 75% B9.11 47 Examined from Pipe side only due to Valve Configuration NG-D-0022A Pipe to Safe End 75% B9.11 48 Examined from Pipe side only due to Safe End Configuration NG-E-0006 Pipe to Valve 75% B9.11 49 Examined from Pipe side only due to Valve Configuration NG-E-0007 Valve to Elbow 50% B9.11 50 Examined from Elbow side only due to Valve Configuration NG-E-0016A Elbow to Valve 50% B9.11 51 Examined from Elbow side only due to Valve Configuration

Request for Relief (R-45) for Obtaining the Required Percentages During the Fourth Interval for Class 1 and 2 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 4 of 6)

Table R Limited Weld Coverage Weld Description Coverage Item Figure Notes NG-E-0017 Valve to Pipe 50% B9.11 52 Examined from Pipe side only due to Valve Configuration NU-2-0001 Pipe to Valve 50% B9.11 53 Examined from Pipe side only due to Valve Configuration NZ-3-0082 Valve to Elbow 75% B9.11 54 Examined from Elbow side only due to Valve Configuration ND-10-0021 Pipe to V-16-0061 50% B9.11 55 Examined from Pipe side only due to Valve Configuration NU-3-0006 Valve V-17-54 to Pipe 50% B9.11 56 Examined from Pipe side only due to Valve Configuration NU-4-0003 Tee to Valve 50% B9.11 57 Examined from Tee side only due to Valve Configuration NZ-3-0005 Valve to Tee 39% B9.11 58 Examined from Tee side only due to Valve and Tee Configuration NZ-3-0023 Pipe to V-20-0150 50% B9.11 59 Examined from Pipe side only due to Valve Configuration NZ-3-0024 Valve to Tee 48% B9.11 60 Examined from Tee side only due to Valve Configuration NZ-3-0028 Elbow to Valve 50% B9.11 61 Examined from Elbow side only due to Valve Configuration NZ-3-0029 Valve to Elbow 50% B9.11 62 Examined from Elbow side only due to Valve Configuration NZ-3-0032 Tee to Valve 44% B9.11 63 Examined from Tee side only due to Valve Configuration NZ-3-0033 Valve to Elbow 50% B9.11 64 Examined from Elbow side only due to Valve Configuration NZ-3-0052 Valve to Tee 43% B9.11 65 Examined from Tee side only due to Valve Configuration NZ-3-0056 Valve to Elbow 50% B9.11 66 Examined from Elbow side only due to Valve Configuration NZ-3-0070 Valve to Tee 44% B9.11 67 Examined from Tee side only due to Valve Configuration NZ-3-0076 Pipe to Valve 50% B9.11 68 Examined from Pipe side only due to Valve Configuration NZ-3-0077 Valve to Elbow 45% B9.11 69 Examined from Elbow side only due to Valve Configuration NZ-3-0081 Pipe to V-20-0023 50% B9.11 70 Examined from Pipe side only due to Valve Configuration RF-2-0115 Valve to Pipe 87% B9.11 71 Examined Limited due to Valve and Pipe Configuration NZ-3-0004 Pipe to Valve V-20-0015 50% C5.11 72 Examined from Pipe side only due to Valve Configuration V-1-173 EMRV Valve Body Weld 82% B12.40 73 Limited Coverage due to Welded Pilot Valve and Name Plate Valve Body Interferences (B-M-1)

CD-14-OO1B/ Hemi Head to Nozzle 50% C2.21 74 One sided Examined from Hemi side due to Nozzle Configuration (C-B) 211-C-6 Weld

Request for Relief (R-45) for Obtaining the Required Percentages During the Fourth Interval for Class 1 and 2 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 5 of 6)

Table R Limited Weld Coverage Weld Description Coverage Item Figure Notes CD-14-001B/ Hemi Head to Nozzle 50% C2.21 75 One sided Examined from Hemi side due to Nozzle Configuration (C-B) 211-S-6 Weld

Request for Relief (R-45) for Obtaining the Required Percentages During the Fourth Interval for Class 1 and 2 Component Inspections In Accordance with 10 CFR 50.55a(g)(5)(iii)

(Page 6 of 6) 5.0 BURDEN CAUSED BY COMPLIANCE The required ASME Code coverage is impractical for the subject welds since the components would require design modification that would impose a significant burden to Exelon Generation Company, LLC. At Oyster Creek Nuclear Generating Station, qualified PDI ultrasonic examination techniques have been used as required. There are no single sided examination procedures available for examination of austenitic piping welds and there are no qualified procedures for examination of cast materials; therefore, many welds may only be examined for 50% of the required examination volume. Other limitations are due to plant design/condition that would require changes to the plant installed condition to allow greater coverage.

The inspection results for the limited weld examinations listed in Table R-45 did not identify any unacceptable indications.

6.0 PROPOSED ALTERNATIVE AND BASIS FOR USE No alternate provisions are practical for the subject welds. Examinations were performed to the maximum extent practical with the best available methods at the time of the examination.

7.0 DURATION OF PROPOSED ALTERNATIVE This relief is requested for the fourth 10-year ISI interval for the Oyster Creek Nuclear Generating Station, which ended on January 14, 2013.

8.0 PRECEDENTS Similar relief requests have been approved for:

1) The Creek Nuclear Generating Station (OC-35), in U.S. Nuclear Regulatory Commission Safety Evaluation Report dated February 2, 2005.

2) The Limerick Generating Station, Units 1 and 2 (Relief Request RR-35) in a U.S. Nuclear Regulatory Commission Safety Evaluation Report dated January 27, 2009.

3) The Peach Bottom Atomic Power Station, Units 2 and 3 (Relief Request 13R-49) in a U.S.

Nuclear Regulatory Commission Safety Evaluation Report dated August 27, 2010.

Site: Oyster Creek Unit: 1 Report Nu .

GE NUCLEAR ENERGY Plot Sheet Project: JR20 8657 System: Cont. Spray Component ID Number: NQ-2-0215 Configuration: BRANCH PIPE Each Scan below is weighted 25% for a total of 100% coverage.

Two directional coverage is required for axial scan.

Circ Scan CW = 0.0%

Circ Scan CCW = 0.0%

Axial Scan Upst = 0.0%

Axial Scan Dnst = 100%

Code Coverage achieved is 25%

Chad Olson 1/ 11/3/2004 e Lae i Ri Initials: Examiner: Level: Date: GE Reviq-m~d Byw Level: Date: Utility Reviewed By: Date: e 6B:Date:

o Page 6 of 6

Wall Thickness Site: Oyster Creek Unit: I Report No.:

GE NUCLEAR ENERGY Profile Sheet Project: 1R20 005294

_________ _______________________ _______________ .1.

System: Iso. Cond.

Component ID Number: NE-5-0002 1."15 90* 180*

Position I

0.

4- I 4-270° Ii 2M3 NIA NIA NIA WA Crown Height: Flush 2 0.88 WA WA WA Crown Width: 1.3" Safe End Elbow 3 0.92 WA WA WA UPST Component: DNST Component:

Nominal Diametei 10 In.

4 0.8 WA WA N/A Weld Length: 33.50 In.

510.64 WIA NAV NAV T&C's taken from previous data report no. OCR19-047 dated 10/12102.

6OV. Paul Valden II 11/13/2004 -ll *0-- X Initials: Examiner: Level: Date: GE Reviewed By: Level: Date: Utility Review: Date: ANII Revie,- Date:

Page 4 of I

Wall Thickness Oyster Creek Unit: I Report No.:

GE NUCLEAR ENERGY Profile Sheet 1R20 005296 System: Iso. Cond.

Crown Height: FLUSH Crown Width: 1.3" SAFE END ELBOW UPST Component: DNST Component:

Nominal Diameter 10 in.

Weld Length: 33.50 in.

T&C's taken from previous data report no. OCR19-048 dated 10/12/02.

0>

6)V__ Paul Valden II 11/13/20 Initials: Examiner: Level: Date: Utility Review: Date: ANII Review'! Date:

Page 4 of 4

Wall Thickness Site: Oyster Creek Unit: I Report No.:

GE NUCLEAR ENERGY Profile Sheet Project: IR20 005334 System: Recirc Component ID Number: NGD-0002 Position 0* 900 180* 270°

.1 I 1.35 N/A N/A N/A Crown Height: FLUSH 2 1.3 N/A N/A NA Crown Width: 2.0" ELBOLV PIPE 3 1.25 N/A NA NWA UPST Component: DNST Component:

Nominal Diameterl 26 In.

4 N/A N/A MA NIA IIII Weld Length: 84 In.

5 N/A N/A N/A N/A FLOW

-- /

/

\\ /

X /

\/

PbI,,ajj pXM pg*VIov.L DrIrA, i--nils James Wiiamrn* ft 119/2004 ///74 lni~is. Examiner: Level: IDate: GE Rev Level: Date: Utility Review: Date: ANII Review(/ Date:

Page 4 of 4

Wall Thickness Profile eet Site: Oyster Creek Unit: 1 Report No.:

Ip 'GE ENERGY NUCLEAR Project: 01R21 IR21-100 System: Iso-Cond Component ID Number: NE-2-0061WELD Position 0. 90" 180° 270*

1 0.58 MA WA WA Crown Height: Flush 2 0.54 NIA WA WA Crown Width: /-3" PIP*E iVALV 3 0.58 WA NA WA UIPST Component: ONST Component:

Nominal Diameter 10-V 4 WA WA WA N/A Weld Length: 34.01 5 MA MIA MA WA FLOW

- N(=- a -oci .

THIjCJ4AJ1.3 AtAO CCIJ.bQI -rAKsxI " 04 ~

I S2Iinbuer Tro U 1OZV200 _--V Drawn by: Level: Date: GE Reviewed By: Level: Date: tqili ýReview: Date: ANII Review: Date:

Page I of 4

Wall Thickness Profile bet Site: Unit: 1 Report No.:

__ "GEENERGY NUCLEAR Project: OIR21 1R21-10-4 System: iso-Con Component 1D Number: NE-2-0256 WELD 1E5D 5.

Position 0. go, 180s 270*

1 0.6 N/A I/A N/A Crown Height: Flush 2 0.58 V/A N/A ./A Crown Width:

3 0.56 MIA WA WIA UPST Component: DNST Component:

Nominal Diameter 4 0.58 NWA W/A N/A Weld Length:

WA IVIA W/A IVA FLOWN

.~-THciA~t~ t'A~CO#J'IQjP -GA9K. reAOt QQo0 DA1V~

9 Troy Steinfauer 10t21/20 _ _e Drawn by: Level: Dale: GlEReviewed By: Level: Date: Re*,*. Date: ANII Rp"W - Date:

Page I of,

Site: Oyster Creek Unit: I Report No.:

__" GE ENERGY NUCLEAR Project: OIR21 IR21-103 System: Iso-Cong Component ID Number: NE-2-0255 WELD

-~ 15" Position 0. 90G 180" 270" 1 N/A N/A N/A N/A ~ E~1 Crown Height: f/ust 2 0.56 N/A IWA N/A Crown Width: 0.5 VALVE &P oe 3 0.55 N/A N/A N/A UPST Component: DNST Component:

Nominal Diameter 10.0 4 0.55 N/A N/A N/A Weld Length:

5 0.60 W/A NIA NAV FLOW Sp VALV J-Ae- 7"-

M~ -

AM~P8Af4t6 AWD ia,ý d-h)rxi j~Cv 00 DT Troy tawinbyur He a0 :eZ20B : Date:

Drawn by: Level: Date: 48r~viewdBy: - Level: Date: Date: ANII eview: Date:

Page I of

Wall Thickness Profile Sheet I site: Oyster Creek Unit: I Report No.:

GE ENERGY NUCLEAR Project: OIR21 1R21-.10 I

System: Iso-Con 1.5"1.5"1 Component ID Number: NE-2-0257 WELD Posion 0° go 180° 270 I N/A NIA N/A NIA Crown Height: BOusA 2 0.56 N/A N/A NA Crown Width: OX 3 0.56 NIA MA NA UPST Component: DNST Component:

Nominal Diameter 4 0.58 1NA WA /A Weld Length:

5 0.58 NAII W/A MIA FLOW-'

'I

,Y-"JCKJ4&4 A#4,0 Cw~JTM(CJ6k TAKIW gao QO AT 2ooa S Troy steinbaur # 10/21/2006 ..

Drawn by: Level: Date: CýEAOvlewed 'By: Level: Date: ' ýRevlew: Date: ANII Review: I Date:

Page I of 4

Wall Thickness Profile Sheet Site: Oyster Crek Unit: 1 Report No.:

GE ENERGY NUCLEAR Project: OIR21 1R21-108 System: ISO-Cond 1.5" Component ID Number: NE-2-220 WELD Position 0. 90g 18O 270° W

AA NA WA WA Crown Height:

2 WA WA WA WA Crown Width: F0-0h 3 0.85 WA WA /A VALVE PiE UPST Component: DNST Component:

Nominal Diameter 4 0.7 WA WA WA Weld Length:

5 0.8 WA W(A WA FLOVV vALvV(

u4;0L L

q5 S V~ "pw AAO C*ojlý'J 1141 ~A 60cIIi InAocr" A- 321 Troy S.einbau # M 912006.. . .3.. 0.. Pa e i4 de Drawn by: Level: Date: evee B2 y Level Dae UdW~Revi'ew: Date: ANII Review.te Page I of _

Wall Thickness Profile Sheet Site: Oyster Creek Unit: 1 Report No.:

GE ENERGY NUCLEAR OIR21 IR21-107 Project:

System: Iso-Cond 1.5" Component ID Number: NE-2-240 WELD Position 0° 90" 180 270° 2115 1 WA N/A /A WA Crown Height: ROuAf w

2 WA N/A WA WA Crown Width:

VALVpi 3 07" WA WA WA UPST Component: DNST Component:

Nominal Diameter 4 0.67" NA WA IA Weld Length:

5 089" WA WA MIA FLOW pilk-2a-14 FluaD ý+eAl>

CQ)

-I,1A I ',ý kTtIcICa4&* AAJ Cewryv& 'r*XL#4 Fllai I10k) Dqir4 A- 1a 80A"It do p Trov Steinbauer II 0/1/200 Drawn by: Level: Date: Levie Byw:J Level: Date: - ,-Uli4 Review: Date: ANllJePgewK Date:

Page 4 of .

Site: Oyster Creek Unit: 1 Report No.:

S*'GE ENERGY NUCLEAR Project: IR21-112 OIR21 System: Iso-Con

- 1.5.. 1.

Component ID Number: NE-5-206 WEL Crown Height: RLuam Crown Width:

VALVE UPST Component: DNST Component:

Nominal Diameter Weld Length:

FLOW; PIPE VALVE Tod Gi4de 4/J420 Drw by evl Dt: e eiwe Y 'ev Date:

Drwnby Lve Dt G Rvewd yLevel: Date: Utility Review. Date: ANI Review:

Page of~

Sitew Oyster Crook Unit: I Report No.:

SGE ENERGY NUCLEAR Project: OIR21 1R21-113 System: Is-Cond Component ID Number: N-5.214 WELD Posion 0. 90g 180 270' 1.5" 1.5 1 0.73 NA N/A N/A Crown Height:

2 0.84 N/A MIA /A Crown Width:

3 0.8 NA MIA NA Nominal Diameter 109 4 NA N/A NA NA Weld Length: 340=

N/A W/A N/A 5 W/A FLOW'

-;4AL Vr

&o"AL 3& "1NIC4..K1b 4,O *CJ3C~ "rKk* efR*P liiil DATA

.'0- 4 0 d,1" Troy S beinbar ev D0/19/200t /IE-#- ec Drawn by: Level: Date: GE Reviewed By: Level. Date: g4Review: Date: ANiReview: L Date:

Page A of

Wall Thickness ProfileSheet Site: Oyster Creek Unit: 1 Report No.:

01"'IGE ENERGY NUCLEAR Project: oIR21 IR21-206 System: Shutdown Cool Component ID Number: NU--1 WELD Position 0 90W 180* 270° ifi M2 1 -1 [51 1 WA WA WA WA Crown Height:

2 WA WA WA WA Crown Width:

3 0.67 WA WA WA UPST Component: DNST Component:

Nominal Diameter 4 0.67 WA WA WA Weld Length:

5 0.79 WA W(A IVA FLOW*

VAI. Vt:

I J Troy Steinbauer L# 1k/20/20 - .."IV"'

Drawn by: Level: Date: GE Reviewed Byý/' Level: Date: Review: Date: APDage4 V 4 Page A of -4

.Q1.

Wall Thickness Profile Sheet site: Oyster Creek Unit: I Report No.:

---101GE ENERGY NUCLEAR OIR21 1R21-2 Project:

System: Clean-Up Detmin Component ID Number: ND-10-0-00 Position 0. gO. 180° 270' 1 .44 N/A N/A N/A Crown Height: FLUSH 2 .43 N/A N/A N/A Crown Width: .7 3 .48 N/A N/A N/A UPST Component: DNST Component:

Nominal Diameter 4 .48 N/A N/A N/A Weld Length: 2.0' 5 N/A M/A N/A N/A P I i~E \J Lt\IF-

~- j~g'~ ~

Drawn by: Level: Date: GE Reviewed By. Level: Date: rltRevieOw: Date:

Page I of I

et Site: Oyster Creek Unit: I Report No.:

."O'W/GE ENERGY NUCLEAR Project: OIR21 IR21-025 System: an-Uo Detain Component ID Number:

Crown Height:

ND-1O-OOOg WELD Ell Crown Width:

UPST Component: i.DNST Component:

Nominal Diameter Weld Length: ILE n FLOWn Thickness and Profile taken from 1991 data.

Drawn by: Level: Date: G ee y,/ Lvl ae Review: Date. AN6 eview:./ Date:

Page of It

Site: Oysier Creek Unit: I Report No.:

GE ENERGY NUCLEAR Project: OIR21 IR21-178 System: , fif

- 1.5" .. C Component ID Number: NG-A-O7 WELD 1.5 1, Position 0. 90* 180° 270° 1 1.08" W/A W/A W/A Li _EJ Crown Height: Flush 2 1.08" W/A W/A NWA Crown Width: Iii:

VALVEN Co 3 1.26" NWA W/A WA UPST Component: DNST Component:

Nominal Diameter ILE0 4 1.1" WA WVA WIA Weld Length:

5 1.24" MA WA WIA FLOW FLo~j "(2 -A0-4ITICKNE-LS AA40 O ,rowa -rAKk#4~~I Ic~f07 Troy Stinf( IIi 10_2/20 Drawn by: Level: Date: Reviewed: Level: Date: Ili Review: Date: ANII Review: Date:

Page !, of I

GE ENERGY NUCLEAR Wall Thickness Profile t~haet I Site: Oyster Creek Unit: I Report No.:

Project: 01R21 1R21-177 System: Rx Recir Component ID Number: NH.--0006 WELD

- 1.5-" -

1 ý.5" -

Position 0. 90° 180, 270*

1 1.06 N/A N/A N/A Crown Height: fElish 2 1.1" N/A N/A N/A Crown Width: //3" 3 1.12" N/A N/A N/A Component: FPST DNST Component:

Nominal Diameter 2=

4 1.08" N/A N/A N/A Weld Length: 12E 5 1.05" N/A NAV N/A FLOW; I

FL & non - bt, A O0, 6eAL 4S*! I'O4L

VJCkIC0ý4 AMD C.OJQJO(Jf, T-rAKA:N %~~I:b1 JIVI P4Ar j Troy Steinbavlr !! 10/24/200i to-Z7_

Drawn by: Level: Date: Reviewed B Level. Date: Date: AN 4levrew" Date:

Page 4 of I

Report No.:

0 *GE ENERGY NUCLEAR Site:

Project:

Oyster Crook 01R21 Unit: 1 IR21-179 System: Rx Recirc Component ID Number: NG-A-O014 WELD 1."1.5" -

Poaton 0. WO 18o 270*

1 WA IVA WA WA Crown Height:

2 1.12 WA WA WA Crown Width:

3 1.24 N/A NA NA UIPST Component: I DNST Component:

Nominal Diameter 4 1.24 WA WA WA Weld Length:

5 1.24 Nf/A N/A NAV PLAMP RAlm. ELBOW Cot

-MY.94 FfVM IqI Pp;EVotS £MAr R-15(v Todd Ginder Drawn by:

Le LevlG

Dat:

eiwdB: OLvl ae a0/25/200ev Date:

Review: Date: ANII Review.

Page I Date:

of4

Oyster Creek Unit: 1 Report No.:

GE ENERGY NUCLEAR Wall Thickness Profile SheetI Site:

Project: OIR21 IR21-180 System: Rx Recir 1.5" Component ID Number: NG-A.O018 WELD -1.5".

Position 0. 90° 180° 270" 1 1.30 WVA WlA WVA m

Crown Height: Flush 7- 1.12 NWA NWA WA Crown Width: 1.3 ELBOW VALT opoet 3 1.06 W/A NWA N/A UPST Component: DNTCmoet Nominal Diameter a.

4 1.08 WA WA WA Weld Length: 82.0" 5 WA MA WA MA Thickness and profile taken from 1994 data.

4oF~L~

"\ / VALVEI I jKurl Baum*amn i 10/27/200 Drawn by: Level: Date: Level: Date: i Review: Date: ANIlI Review: Date:

Page I of 4

Wall Thickness Profile S aeet - Site. Oyster cree Unit: 1 Report No.:

_ GE ENERGY NUCLEAR I Project: 01R21 lR21-194 System: Rx Recirc 1.5" 1.5" _

Component ID Number: NG-B-000 WELD Posibon 0. 90 180* 270*

1 WA N/A NIA NIA Crown Height: Rush 2 1.08" WA N/A NA Crown Width: lie 3 1.24" N/A N/A NA Nominal Diameter toiiC 4 1.28" N/A N/A NIA Weld Length: I20 6 1,28" W/A M/A WNA 0

L4s°S

//

VAL-V~' \ /

Drawn by: Level: Date: GE By Level: Date: iDate ReDate: ANII Review:

Page I of I

Profi.. S-eet.

Oyster Creek Unit: I Report No.:

GE ENERGY NUCLEAR Wall Thickness Profile Site:

S Project: 01R21 1R21-185 System:

Component ID Number: NG-S-0012 WELD - 1.5-" -1 1 1.5" Position 0. 90" 180" 270° 1 WA WA N/A MIA Crown Height:

2 1.35 MA N/A N/A Crown Width: 1.701" 3 1.40 NA MA NA UPST Component: iDNST Component:

Nominal Diameter 2W 4 1.35 N/A M(A NA Weld Length: fix 5 1.35 NAV NAV N/A Thickness and Contour taken from 1989 data.

IN~

LIS__

(0 0 "JZL

/

F -n/- J'\ /- -

I Drawn by: Level: Date: GE Reviewed By: Level: Date: Utility Revidw: I Review:.

Page I of 4

Site: Oyster Creek Unit: I Report No.

GE ENERGY NUCLEAR Project: OIR21 1R21-183 System: Rx Reci Component IDNumber: NG.B-OW5 WELD Positon o° 90" 1800 270o 1 1.05" WA WA WA Crown Height:

2 1.05" NA WA WA PIPE VALE Crown Width:

3 1.10" WA WA WA Egg. UPST Component: DINISTComponent:

Nominal Diameter 4 WA WA WA WA Weld Length:

5 WA WA W/A WA Thickness and Contour taken from 1994 data.

q50C.

4

~~1

/<

5Kurt Baum an l10/24/20 --X 1/O*7yt ____ -31_______

69 Drawn by: Level: Date: GE Reviewed By:O" Level: Date: Utility Reviek Dat A611 Review: Date:

Page 4 of4

Site: Oyster Creek Unit: 1 Report No.:

O GEENERGY NUCLEAR 1R21-185 Project: 01R21 System: Rx Recir Component ID Number: NG-B-0016 WELD 1.5" 1.5 Powtion 0° 90g 10" 270" 1 1.26 WIA W/A WA Crown Height:

2 1.32 N/A WA WA Crown Width:

ELO VAL 3 1.22 N/A WA WA 82-0h UPST Component: DNST Component:

Nominal Diameter 4 1.12 MA WA WA Weld Length:

5 MA NIA WA MA FLOWA (J2I o 'L L45~

[14al,5

\ /

L 10/25/200 Drawn by: Level: Date: Level: Date: Review: Date: Date:

Page I of I N*

GE EEYWall Thickness Profile Ahcet site: Oyster Creek Unit: I Report No.:

E ENERGY NUCLEAR Project:

OIR21 1R21-190

... . ql I PrIo ect:

System:

Position 0. 9go 180° 270' Component ID Number: NG-C-O05 WELD °- I 1 N/A W/A N/A WA Crown Height: FLUSH 2 1.04 N/A NWA NWA Crown Width: 1L.

3 1.06 WA W/A NIA UPST Component: .DNST Component:

Nominal Diameter ILE 4 1.20 WVA NWA WA Weld Length:

5 1.24 WA WA FLOW*

NAV

'TAýFN fZMim9^IO4SAT i iAkz R- 113 DTadd Gbn Drawn by: Level: Date: viewed By. Level Date: Review. Date: ANII Review: Date:

Page I of I

Wall Thickness Profile Sheet site: oyster Cree Unit: 1 Report No.:

GE ENERGY NUCLEAR Q=B~ 1R21-192 Project:

I System: Rx Recirc Component ID Number: NG-C-0012 WELD C- 15" Position 0. go0 180s 270' F371 W

M/A W/A WA WA Crown Height: E/s 2 1.40 WA WIA N/A Crown Width: .375" 3 1.52 W/A WA N/A EELSO UPST Component: I DNST Component:

Nominal Diameter 4 1.48 NIA WA W/A Weld Length:

5 1.48 WA WA WA FLOW*

CL

'JC--Drawn by: Level: '~tj GE Revlo Level: Date. , Review. Date: ANII Review: j Page Date:

4 of 4

Site: Oyster C Unit: I Report No.:

___GE ENERGY NUCLEAR Project: OIR21 System: Rx Recir Component ID Number: NG-C-O016 WELD Position 0. 90. 1800 270" 1 1.25 WIA WA NWA Crown Height:

2 1.23 WA WMA WA Crown Width:

3 1.18 N/A WA NWA UPST Component: . NST Component:

Nominal Diameter 4 1.10 W/A WA WA Weld Length:

5 WA t W NIA WA IiFLOWV qS 11 (Q Ge It F- - _

Dura wunby: Le Dte:

1-1._- , / ,.*

, c. :z- ,,

Drawn by: Level:Dae GE Reviewed By: Level: Date: , Review: Date: AN Reviewa Date:

Page I of I

Site: Oysteor Creek Unit: 1 Report No.:

O GE ENERGY NUCLEAR Project: OIR21 IR21-189 System: Rx Recarc Component ID Number: NG-C-O4 WELD Postuon 0. 90 180" 270" 1 1.08 N/A N/A N/A Crown Height: E/uah 2 1.08 N/A N/A N/A Crown Width: 1U 3 1.12 NIA N/A N/A UPST Component: 1NST Component:

Nominal Diameter 2.0 4 1.08 N/A N/A N/A Weld Length: i2.0 5 1.12 NIA NAV N/A TAY~aý FPOA ýc"9i- PkeJ KqS Dxrý R-Todd Ginber /i 10/2d/200 //,,2 -"06 Drawn by: Level: Date: Revie y Level. Dt Date: ANII Review. $ Date:

Page I of A

HITACHI Wall Thickness Profile Sheet Site:

Project-Ouster Creek OC 1R22 1.5' Unit: 1R22 I Report No.:

0C1R22-079 1 .5" System: 215 Component IDNumber: ND-10-0020 Position I O° 90* 180° 270*

1 N/A N/A N/A N/A Crown Height: Toper 2 N/A N/A N/A N/A Crown Width: 0.?7" Valv.e Pipe 3 0.583 N/A N/A N/A UPST Component: DNST Component Nominal Diameter: 6.0Y' 4 0.427 N/A N/A N/A Weld Length: 21.0' 5 0.429 N/A N/A N/A FLOW V3qLVE ci-1 o R1e E I'A Dickey Michael HI 11/4/2008 4 ~ A44JLI Drown by: Level Date:01eiw Level: Dote: ( eviewed B; -- vl

-vel: o:

ate: Utility Review: Dote: ANII Review: Date:

Page 4 of 4

Wall Thickness HITACHI Profile Sheet Site:

Project: Oyster OC I R22Creek Unit: IR22 Report No.:

OCIR22-090 I L.............

1.5 5" =

System: 225 Component I1 Number: ND-1-0029 WELD Position 90* 180" 270° 4 4- --

1 0.48 N/A N/A N/A Ctown Height: Flush 2 0.50 N/A N/A NA Crown Width: 0.70" ELBOW VALVE 3 0.60 NIA WA WA UPST Component: . DNST Component Nominal Diameter: 6._"

4 WA N/A /A /A 7.

5 N/A N/A N/A N/A Weld Length: 2125" FLOW;

__________ I _________ _________ .3. _________ 1 _________ .2. __________________________________________________________________

THICKNESS &CONTOUR TAKEN FROM PREVIOUS DATA REPORT #R-022, OCTOBER 12, 1998.

0b

( VALVE rPauby:ctia Dote: LL Dote: Utility Review, Dote: ANII Review:

Dn wn by: Level: Dote: B reeeei Dote:

Poge 4 of 4

Wall Thickness Profile Sheet Crown Height Flush Crown Width: 1.0*5 PIPE VALVE UPST Component DNST Component:

Nominal Diameter: 8.0""

Weld Length: 26.0" FLOW 0-PROFILE TAKEN FROM PREVIOUS DATA REPORT #R-094, 10/06/1994

'4

\~ .)~

HITACHI Wall Thickness Profile Sheet ,NI Site:

Project:

Oyster Creek OC 1R22 Unit: 1R22 Report No.:

0C1R22-098 System: 2._11 Component IDNumber: NE-2-0254 WELD 115" --

Position 0 1 90, 180" 1 270*

E-L 1 l I F~1 l I 1 0.58 N/A N/A N/A Crown Height: Flush 2 0.58 N/A N/A N/A Crown Width: 0.438" PIPE .VALVE 3 0.56 N/A N/A N/A UPST Component: i DNST Component Nominal Diameter: 10.0o' 4 0.58 N/A N/A N/A Weld Length: 34.0" 5 1 W,A N/A N/A N/A FLOW*

T&C TAKEN FROM PREVIOUS DATA REPORT #R-945, 10/29/2000 Paul blecho 11 111612008 Dote ied:)rv: Doe UtltyRviw //_ , Dat e Drawn by-. Level: Date: G6 Pviewed By,ý' 'tevel: ae Utility Review: Date: ANII view. ,-.,.--ff Date:

Page 4 of _

0 C

34 FIGURE 34 - DELETED 34

Wall Thickness'ý Ste:

Profile Sheet Project

- 1 . "-

Crown Heit Crown WtdthK It UPST Component DNS7 Comp~onent Nomwnol Diameter.

Weld Length:

VALVE #W% (j~

U' TE" Tccike i1om Picuila 4, D414 Qfi ( k Oi M ca el

Wall Thickness Profile Sheet Crown Height Flush Crown Width: 1.6' Valve UPST Component DNST Component Nominal Diameter: 26.0.'

weld Length: 82.0_"

No. R-160, 10/13/1994.

E7~N Aj

/

v4Lv5? ,1

/

Wall Thickness Report, Profile Sheet 0C1R22-108 Crown Height: Tapered Crown Width: 1.4' Valve piope UPST Component DNSI Component Nominal Diameter: 26.0' Weld Length: 83.0" voýl Ve-400Is .5

\-I'-- 4S. th

Wall Thickness Site: Oyster Creek Unit:

Profile Sheet Project: OC IR22 15"

[i Crown Height: 0.05" Crown Width: 0.75" VALVE PIPE UPST Component: DNST Component Nominal Diameter: 6.0" Weld Length: 21.0" I() /.S J.Mike Sullen Drawn by.

Wall Thickness Unit: I Profile Sheet M3 Crown Height 0.0.5" Crown Width: 0.801_,

ELBOW VALVE UPST Component: DNST Component Nominal Diameter: 6.0" Weld Length: 21.('.

FLOW W 7U15 q5'~*

rI

Wall Thickness Unit- I Profile Sheet Crown Height: 0.0s,~

Crown Width: 0.80" Tee LIPSI Component DNST Component Nominal Diameter: 4.0" weld Length: 14. 0" LJ* 70' likeAp From Peuiots Dc,4c

Wall Thickness Site: Oyster Creek Unit: 1 Report No--

iQ) HITACHI Profile Sheet Project: 1R23 IR23-058 1 iiiiiii - I -

5ystem: 215 1." 1.5"2 Position 0° 90° 180° 270*

Component ID Number: ND-1O-0008 WELD EYI"-

1 N/A N/A WA N/A Crown Height: Flush 2 N/A N/A N/A N/A Crown Width: 0.9in Value i Elbow 3 .60 N/A N/A N/A UPST Component: DNST Component Nominal Diameter: 6.0 in

.55 N/A N/A N/A weld Length: 21.0 in 5 .55 N/A N/A N/A FLOW-FL;JJ f L k6'

ý E , t.;) C- X " (- ; - T -T " t v,.-? iýý .'-' J- P. f. ý ; - ý, =ý r-ý- , 6 b k-:,t Mark Hulborn 11,21 4=kI - 4' Drawn by: Level: Dote: Review Dt U R Date: ANII Review: Dote:S Page 5 of 5

Wall Thickness N-/ Site: cyster Cie UnA: Rtpcwt HtITACHI-Profile Sheet I IR2"14

-- ~ I System: MU

- V- V - V- * - Component IDNumber:; 0-MWEL 1.5" O" 90* 1W0k 2?0" I 2.20 W/A WA WA Crowntieighl 2 LIS WA WA WA Crown Width LitD ME I L16 WA WA NWA

. IU UPSTCOmponent Component Nominal Dameter:

4 2.31 WA NWA WA Weld Lengtk.

5 1JO WA WA WA

_________ _______________________________________________________________ I Drown by. Levet Dote: ~ pE# vedr 16 11-7 Date: Utdity Review, Dote AMII Review. Date

________~~~~~~~~o _ _ _ _ _ _ _ 1 _ _ _ _ _ _ _ I__ of A__

Wall Thickness Profile Sheet 1.511 Crown Height: Flush Crown Width: 1.4 in Pipe Valve UPST Component- DNST Component:

Nominal Diameter: 26.0 in Weld Length: 84.0 in

%-/a-IAIý

223 Coverage Calculation Scanned area Upstream - 2.34"sq -(1.2x.9)/2 = 1.80" sq Dnstream - 2.34" sq - ((1.5x.91+(.7x.9)/2]= .67"sq CCW - 2.34" sq - (1.5x.9)= .99" sq CW -2.34" sq - (1.5x.9) = .99"sq Total 4.45" sq 00ge Arke Code Box = 2.6x.9 = 2.34" sq Actual Box = 2.34" sq - (.45x.9")/2 = 2.13" sq Total Code Coverage = 2.13 x 4 scans 8.52"sq Total Area Scanned = 4.45"sq therefore 4.45/8.52 x 100% = %52 nes Setzer 0 1 11/I 7/2010 Drown by. Level: Dote: Page 29 ofZ

HITACHI Wall Thickness I,- Site: Oyster Creek Unit: 1 Report N*

Profile Sheet Project: 1R23 1R23-077

-I-System: 223 1.5" 1.5" Component ID Number: NG-D-0015 WELD '

Position 0. 90° 180° 270" 2

.4- .4-I 1 1.33 N/A N/A W/A Crown Height: Flat 2 1.33 N/A N/A N/A Crown Width: 1.2 in Elbow Valve 3 1.18 N/A N/A N/A UPST Component DNST Component Nominal Diameter: 26.0 in 4 1.13 N/A N/A N/A weld Length: 83.0 in 5 1.16 N/A NWA N/A FLOW1

'4; T EL13OW VAiL VC

.FLOW NG - - 005 F 4? Jack Reisewitz li 1119/2010 /____

Date:

____//_______________1]

Utility Review:

Date: . Date:

Drown by: Level: Date: GE e edBy: Level:

Page 4 of 4

Wall Thickness Site: Oyster Creek Unit Report IM HITACHI Profile Sheet Project: 1R23 1R23-078 i -Vý Mond I System: 223 1.5" 1.5" Component ID Number: NG-D-0016 WELD Position 0. 90* 180° 270" w'l D-n n2n 1-1 N/A N/A N/A N/A Crown Height Flush 2 1.18 N/A N/A N/A Crown Width: 1.5 in Valve i DNST Pioe 3 1.22 N/A N/A N/A UPST Component DNST Component Nominal Diameter: 26.0 in 1.10 N/A N/A N/A

.7-l"*

Weld Length: 82.5 in 5 1.12 N/A N/A N/A Thicknesses and contour taken from previous data.

4-\-

FLOW/ NG-L- OO0,

.- Jack Reisewitz

', II11/9/2010/14-/

Drawn by. Level: Date: e*aviewed Bw. Level: Date: Utility Review: Dote: A evie& Dote:

Page 4 of 4

Wall Thickness 2 Site: Oyster Creek Unit I Report Nk&--

HITACHI Profile Sheet Project: IR23, 1R23-079

-4.

System: 223 1 .5" ;"1.5" Position 90, T

180° 2 70' Component ID Number: NG-D-0022A WELD II 1~

1.06 N/A NWA NWA Crown Height: Flush 2 1.06 N/A N/A N/A Crown Width: 1.3 in Pipe Safe End 3 1.12 N/A N/A N/A UPST Component: DNST Component Nominal Diameter: 26.0 in 4 1.14 N/A N/A N/A Weld Length: 82.0 in 5 N/A N/A N/A N/A FLOW o Taken from previous data. See report number R-081.

'PLLOW-

'RE-7PE Zi,4SE EfiZ&

~i~L K,

'\..

7..

/

\4~

\ I I Mark Hilborn 111 11/11/2010ed By_____ _______el:

Drawn by: Level: Dote: G eievel Date: Utility Review: Dote: ANI Date:

Page 4 of 4

Wall Thickness Profile Sheet Crown Height: Flush Crown Width: 2.0 in Pipe Valve UPST Component: ONST Component Nominal Diameter: 26.0 in Weld Length: 82.0 in ITP0E VALVe 6o~i 60 -0

\ \

/

\ ,.'

\ \

\

N. / N V

V \4/

~

Wall Thickness Profile Sheet Crown Height: Flush Crown Width: 1.5 in Valve Elbow UPST Component: DNST Component Nominal Diameter: 26.0 in Weld Length: 83.5 in

4HITACHI Wall Thickness Profile Sheet Site:

Project:

Oyster Creek JR23 Unit I Report N'a 1R23-084 I _________________________________________________________________________________________

System: 223 1.5"1.5" Position 90, 180* I 270° Component IDNumber: NG-E-0016A WELD

"-II l-i 1 : I-1 E@

1 1.30 N/A N/A I N/A Crown Height Flush 2 1.30 N/A N/A N/A Crown Width: 1.5 in Elbow Valve 3 1.18 N/A N/A N/A UPST Component:. DNST Component Nominal Diameter: 26.0 in 4 1.13 N/A N/A N/A Weld Length: 84.5 in 5

J.

NA I

I N/A

_____ I N/A

_____ i N/A

_____ I FLOW 0 Taken from previous data. See report number: R-16R-034.

/

~\ i\ -~/~ -

J o Serth L 1119/2010 _s/, "

Drawn by. Level: Date: " viewed By!. Level: Date: tilit Review: Date: Date:

Page 4 of 4

Wall Thickness - Site: Oyster Creek Unit: 1 Report No'-

HITACHI Profile Sheet Project: 1R23 IR23-085 I .1-system: 223 1.5" _i1.5" Component IDNumber: NG-E-0017 WELD Position 00 90, 1800 270' 1 NWA N/A N/A NWA Crown Height: Flush 2 1.08 WA NA NA Crown Width: 1.5 in Valve__e i 3 1.20 NA NA NA UPST Component: DNST Component Nominal Diameter: 26.0 in 4 1.04 WA NA NA Weld Length: 82.0 in 5 1.02 N/A N/A N/A Token from previous data. See report number: R-16R-016.

(~Q'~k~L.

~\

,i )\

/

'-7

/

/ /

~..< 1/

A /

-1 r

/ ~ ___ Joseph Serth 11 11/9/2010 7,-/ Drawn by: Level: Date: ,,eviewe-d By: Level: Date: l Review: Date: ANII *:ofDte:

Page 4 of 4

. ,j Wall Thickness HITACHI Profile Sheet Sstern: 214 Crown Height: Flush Crown Width: 1.3 in PiSpe Valve UPSTr Component DNST Component Nominal Diameter: 14.0 in Weld Length: 44.0 in VLOVJ PxT F-VALA.W

Iall Thickness Site: Oyster Creek Unit: I Report NL...

HITACHI Profile Sheet Project: 1R23 1R23-141 System: 21..2 1.5" 1 .5" Component ID Number:

NZ-3-0082 WELD Position 00 90° 180° 2700 II 1 1.0 N/A N/A N/A Crown Height: Flush Efl 2 i 4 f 2 N/A NA N/A N/A Crown Width: 0.9 in Valve Elbow 3.545 N/A N/A N/AC UPST Component: DNST Component-Nominal Diameter: 8.0 in 4 .485 N/A N/A N/A __I__ _

Weld Length: 27.5 in 5 .480 N/A N/A N/A FLOW V~~EE.E L. &~Mark Hilborn 111I11/11/12010 V4,ý Ak l7 / 6 0 Drown by: Level: Dote: G Reviewed B6 Level: Dote: Utility Review: Date: ANII Review: Dote:

Page 4 of 4

Report Nc.

Wall Thickness Site: Oyster Creek Unit: I IR24-081_NW HITACHI Profile Sheet Project. 0CIR24 4th Interval/3rdPeriod System: 215 Component ID Number: ND-10-0021 1.5 1.5" Position 0 ° 90 ° 1800 2700 1 .435 N/A N/A N/A * =

Crown Height: Flush 2 .424 N/A N/A N/A Crown Width: 1.0_'

Pipe Valve 3 .540 N/A N/A N/A UPST Component DNST Component Nominal Diameter: 62 4 N/A N/A N/A N/A Weld Length: 21.2._5 5 NIA N/A NIA N/A IF4 Ld kjA pI.pa ~Wd~Z 1Ad4;o~o.

i! 10/21/2712012o Jj.r.-I Initials:

Jack Reisewitz Drawn by: Level: Date: GE Reviewed By Level Date: t ity Review. Date: ANII Review: Date:

Pagej. of,

Report N.*,

ITACHI Wall Thickness *4 I Site: Oyster Creek Unit I 1R24-146 Profile Sheet Project OCIR24 4th Interval/3rdPeriod System:

Position 0° 90° 180° 270° Component ID Number: NU-3-0006 I E%

I1 1 N/A N/A N/A N/A Crown Height Flush 2 N/A N/A N/A N/A Crown Width: 1.3 Valve N ipe 3 .826 N/A N/A N/A UPSI Component: DNST Component:

Nominol Diometer: 14 4 .721 N/A N/A N/A Weld Length: 44 5 .732 1 N/A N/A I N/A 456 ISO F

EL QI- ===-

David Hancock I1 112/2012

C

I Initials: Drown by: Level: Dote: GE Reviewed By: Level: Dote: i Utility Review: Dote: (ANlReview.oe Dote:

Page I Of (

Wall Thickness Site: QytekCeký Unit I Report NCN,,)

.;-..ITAOH2 4th interval/3rd Period Profile Sheet project Component 10Number:

NU-4-0 0 0 3 t/alve Crown Height: FIush Crown Width: 1.10" tee UPST Component: vColvoe Nominal Diameter: DNST Component:

14 weld Length: 44.5 T & Ctakenrfrom previous data Ks~

vs-i TEE VALVif W00

- -I--

FLOW 42 David H q 32012 vel: Date: Utility Review:

initials: Drawn by:

ancock Level: Date B Date:

Review:

ýANII Page 2 ot

Station: Oyster Creek UT Volumetric Coverage Unit: 1 HITACHI Calculation Form Component Number:

. r+nrK ,m I .. LJu, ~

I NZ-3-0005 4 D ")A- 1 I* I Date: 11/11/2012 Coverage Calculations Weld Insoection DtaeConfiguration: Valve to TEE Weld Type Single Sided DiametertNomr: 8" Limitation Type [ Valv j Svern. J22 Y @ Weld C/L [ .seo Examination Box length 1 Weld length (Actual) . Loss Volume Data. Thu majomJy of lmitationis are troie

, tlm,uu* to OD ccnriruradion sucn .= tapers. noop skrin,.aii an.o otner OD p~n corifiguraiin. Thus rtsuLting in 'right side inangie or rectangle snipes of Icss coverg:e. These common gometrc shapes will be used tor determining volumes that have not Dcen examned.

Code Required Volume 7.6 cubic inches Insert "1"for each Determinina volumes loss due to limitation -all dimensions are in Inches Data Sht # Axial Scan Identifier Scan Lenoth Denth Multiole Wald Lonath Conmmants Loss Volume 45 SW Dnstream 0 0.00 0 0 0.00 45 SW Upstream 1.4 0.19 1 28 7.45 70 RL Dnstream 0 0.00 0 0 0.00 70 RL Upstream 1 1.4 0.19 1 28 7.45 0 0.19 0 28 0.00 45 SW Dnstream 1.4 0.19 1 10 2.66 70 RL Dnstream 1.4 0.19 1 10 2.66 0 0.19 0 10 0.00 0 0.19 0 10 0.00 0 0.19 0 10 0.00 0 0.19 0 10 0.00 0 0.10 0 10 0.00 Clrc Scan Identifier t Dt Mulfiplier' Weld Length Comments 45 SW Clockwise 0.7 0.19 1 28 45 SW Counter Clockwise 0.7 0.19 1 28 0 0 0 28 0 0 0 28 0 0 0 28 0 0 0 28 0 0 0 28 0 0 0 28 Total Number of scans 6 Total Aggregate Volume 45.472 Total Aggregate Volume of Loss Coverage 27.864 in cubic inches in cubic inches Resultant loss coverage in %1 60.84% 1Select which coverage applies Examination Coveraaeobtained 39.1§% X ASME Code Coverage GEH Procedure Coverage Page ( of 7 Prepared By: ,- Customer Reviewed By:_

Date: Ii" V*2-*_Z- Date:

Report Nc Wall Thickness

Site: Oyster Creek Unit: 1R24-155*!

ýýAITACHI Profile Sheet Project 0CIR24 4th Interval/3rdPeriod System: 212 Component ID Number: NZ-3-0005 15 1.5" Position 0° 90° 180' 270' 1 N/A N/A 1.16 N/A Crown Height Flush 2 N/A N/A 1.10 N/A Crown Width: .90 3 N/A N/A .58 N/A UPST ComponentF DNST Component Nominal Diameter:

4 N/A N/A .59 N/A Weld Length: 28 5 NIA NINA .64 NINA FLOW" rI4 Troy Huhe 11 1116/2012*

Initiols: Drawn by: Level: Dote: GE Reve d Level: Dote: Utility. Review: Dote: ANII Review: Date:

Page 2- of 7

Unit: 1R24"158t Wall Thickness Site: Oyster Creek IITACH I Profile Sheet ,Project ____

0CIR24 4thReport j Period Interval/3rd System: 212 Component ID Number: NZ-3-0023 Position 0° 90° 180° 2700 1 .45 N/A N/A N/A Crown Height .05 2 .45 N/A N/A N/A Crown Width: .80 3 .49 N/A N/A N/A UPST Component: DNST Component Nominal Diameter: 8.

4 .54 N/A N/A N/A Weld Length: 27.._5 5 .64 NIA NIA N/A FLOW; ELZOID ______ \IAL-vR Troy Huhe It 11/7/2012 C/

Initials: Drawn by: Level: Dote: GE Reviewed By: (_,) Level: Dote: y Review: Dote: ANII Review:. Dte:

Page 2- of 1C1

Station: 0yster Creek UT Volumetric Coverage Unit:1 HITACHI Calculation Form Component Number:

Report Number:

1[R24-159 NZ-3-0024 Date: 11/8/2012 Coverage Calculations Weld Inspection Data Configuration: Vavle to TEE Weld Type Sin le Sided Diameter(Nom): 8" Limitation Type Valve System: z2 1" Q Weld C/L o.58 Examination Box length 1.4 13:.iy of limitations ore those annruut~u to OD coni~uriticn v-uic as t~pvis. nozop siatn,zi~e ara clinci CD Pzz.

Weld length (Actual) 27.6 Loss Volume Data. The mn3 ronlrguratron. Thu.s rusuiting ii 'right s~ae tilangie Lo;rectangle shapes" 0f loss cove~rage Th-ce common geoiletric shapes will Le useu for determining volumes that have not been esamionec.

Code Required Volume 7.5 cubic inches Insert "1"for each oetarminlno volumes lons due tMlimitation - all dimensions am In Inches Data Sht # Axial Scan Identifier Scan 1 .11, r% k U "I It... Uu 1A I.. Comments Loss Volume 45 SW Dnstream 0 0.00 0 27.6 0.0 70 SW Dnstream 1.4 0.19 1 5 1.3 45 SW Upstream 1.4 0.19 1 27.6 7.3 70 SW Upstream 1.4 0.19 1 27.6 7.3 0 0 0 27.6 0 0 0 0 27.6 0 0 0 0 27.6 0 0 0 0 27.6 0 0 0 0 27.6 0 0 0 0 27.6 0 0 0 0 27.6 0 0N 0 0 0 27.6 0 Circ Scan Identifier tler*

Legh Weld Length Comments 45 SW Clockwise 0.7 0.19 1 27.6 45 SW Counter Clockwise 0.7 0.19 1 27.6 0 0 0 27.6 0 0 0 27.6 0 0 0 27.6 0 0 0 27.6 0 0 0 27.6 0 0 0 27.6 Total Number of scans 6 Total Aggregate Volume 44.8224 Total Aggregate Volume of Loss Coverage in cubic inches in cubic inches Resultant loss coverage in %1 52.11% ISelect which coverage applies ExaminationCoverage obtained1 47.89% X ASME Code Coverage GEH Procedure Coverage Page c of ,,*

"-, Prepared By: Customer Reviewed By:_

Date: Date:

Unit I Report No*

Wall Thickness Pr Site: Oyster Creek 0R24-159 0)"ITACH1I Profile Sheet Project 0CIR24 4th Interval/3rd Period System: 212 Component IDNumber: NZ-3-0024 1 1. -

Position 0. 90° 180° 270° 1 .65 N/A N/A N/A Crown Height Flush 2 .51 N/A N/A N/A Crown Width: .80 Valve ITee 3 .58 N/A N/A N/A UPST Component: DNST Component Nominol Diometer:

4 .64 N/A N/A N/A Weld Length: 27.625

.65 1 N/A N/A NIA FLOW.---

vpuvcý pp.

ý-V-z 4:

I 704 Troy Huhe II 11/7/2012 fA&,44 e44,- "ir / I-1 o-it--

Initials: Drown by: Level: Dote: GE Reviewed By: Level: Dote: Utility Review: Dote: ---ANII Review: (. Dote:

Page 2- of 7

Report No.:

Wall Thickness *l"I Site: Oyster Creek Unit I Sr-IITACHI 1R24-160 Profile Sheet Project 0C1R24 4th Intervall3rdPeriod

==mom System: 212 Component ID Number: NZ-3-0028 1.5" .5 Position 0. 90 180, 270' EL 2:4 1 N/A N/A N/A .51 Crown Height: Flush 2 N/A N/A N/A .52 Crown Width: .90 Elbow Valve 3 N/A N/A N/A .51 UPST Component: DNST Component Nominal Diameter:

4 N/A N/A N/A .53 Weld Length: 27 N/A NIA NIA .56 rL~k3L~

VAL-V6;-

I~N.

Cl-7cL L~~459% 7WL Troy Huhe /1 11171202 11 I1a.

21-Drawn by: Level: Date: G;ERviwe By: Lvl Date: Utility Review: Date: " I Reiew Page Date:

-Z_of,

Unit: Report No.

Wall Thickness Site: Oyster Creek hiTrACHI Profile Sheet Project 0CIR24 4th Interval/3rd Period System: 212 1.5" 1.51" Component IDNumber: NZ-3-0029 Position 0. 90° 180' 270° 1 N/A N/A N/A .64 Crown Height .o0 2 N/A N/A N/A .53 Crown Width: .90 3 N/A N/A N/A .53 UPST Component: DNST Component Nominal Diameter: 8.0 4 N/A N/A N/A .53 Weld Length: 27.625 NIA N/A NIA .52 V AŽLV-XI ~Lc~~) FhLW-z T7- Troy Huhe , 1/7201 initials: Drown by: Level: Dote: GE Reviewed By Level: Date: Utility Review: Dote: ANII Review. Dote:

Page 2 - of

Station: Oyster Creek UT Volumetric Coverage Unit:

&HITACHI Calculation Form Component Number:

Report Number:

NZ-3-0032 1R24-162 Date: 11/8/2012 Coverage Calculations Weld Inspection Data Confiouration: TEE to Valve Weld Type Sin Ie Sided Diameter(Noml: a" Limitation Type System: 212 r @ Weld CL I06 Examination Box length [ .4 Weld length (Actual) [ 8.5 Loss Volume Data. Tne m~jo:G.iy ot liminawons ae mose au,iotcu ito i zig,,hution sien as ,per..,,p skrlni.3j= anss cin= OD prt contiguratlon. Thus resulting in 'ogrit side tnlangic or rectangle s.hapes" of loss cc vcrage. Th.se common geometnc shapes willbe used lor determining volumes trial have not been exantifled Code Required Volume 9.2 cubic inches Insert "1"for each Determinina volumes loss due to limitation - all dimensions are In Inches Data Sht # Axial Scan identifier Scan 'Deth Weld Len.th Comments Loss Volume 45 SW Upstream 1 1.4 0.23 1 6.7 2.16 70 SW Upstream 1 1.4 0.23 1 6.7 2.16 0 0.00 0 27.6 0.00 0 0.00 a 27.6 0.00 0 0 0 27.6 0.00 45 SW Dnstream 1 1.4 0.23 1 27.6 8.89 70 SW Onstream 1 1.4 0.23 1 27.6 8.89 0 0 0 27.6 0.00 0 0 0 27.8 0.00 0 0 0 27.6 0.00 0 0 0 27.6 0.00 0 0 0 27.6 0.00 Circ Scan Identifier Lenopth Mulliolie' Weld Lenoth Comments 45 SW Clockwise 0.7 0.23 1 27.6 45 SW Counter Clockwise 0.7 0.23 1 27.6 0 0 0 27.6 0 0 0 27.6 0 0 0 27.6 0 0 0 27.6 0 0 0 27.6 0 0 027.6 Total Number of scans 6 Total Aggregate Volume Total Aggregate Volume of Loss Coverage in cubic inches in cubic inches Resultant loss coverage in %1 56-26% Select which coverage applies Examination Coverage obtained 3.74 X ASME Code Coverage GEH Procedure Coverage Page 6 of 7 Prepared By:_______ Customer Reviewed By:_

.ADate:- -21 Z Date:

Report No Wall Thickness Site: Oyster Creek Unit I 1R24-162 t'ITACHI Profile Sheet Project 0CIR24 4th Intervali3rd Period System: 212 1.5" 1.5" Component ID Number: NZ-3-0032 Position 0 ° 90 ° 180 ° 270 ° 2 4 EI 1 N/A N/A N/A N/A Crown Height Flush 2 N/A N/A N/A N/A Crown Width: .90 Tee Valve 3 .69 N/A N/A N/A UPST Component: DNS Component:

Nominal Diameter:

4 .66 N/A N/A N/A Weld Length: 28.5 5 .66 NIA NIA NIA Thx~

1"-4/ Troy Huhe II 11/I 120-- 27 7 Initials: Drawn by: Level: Date: GE Reviewed By: T ev Date: Utility Review: Date: ANII Revie'w "' Y Date:

Page 2 of 7

Unit: Report N.

Wall Thickness NI Ste: Oyster Creek HITACHI IR24-163 d o Profile Sheet Project 0CIR24 4th Interval/3rd Period System: 212 Component ID Number: NZ-3-0033 1.5" 1.5"1 Position 00 900 180* 2700 1 N/A N/A N/A N/A Crown Height Flush 2 N/A N/A N/A N/A Valve iElbow Crown Width: .90 3 .57 N/A N/A N/A UPST Component: iDNST Component:

Nominal Diameter: 8.0 4 .54 N/A N/A N/A Weld Length: 27.25 5 .50 1 NIA I NIA I NIA

-Fýuý

.411111-7-n 4 Troy Huhe 1- 111712012 i2 Il--o-(t..

Initials: Drawn by: Level: Date: GE Reviewed By: Level: Date: Utility Review: Dote: '---ANII Review: Date:

Page of (

Station: Oyster Creek UT Volumetric Coverage Unit:I

.__ HITACHI Calculation Form rfnmnnnant Mf mh~r I DIn-rf klnJh~ r I k17-A4-AAF9 i g,'.-1RR Date: 11/11/2012 Coverage Calculations Weld Insoection Data Configuration: Valve to TEE Weld Type Single Sided Diameter(Nom)7 8' Limitation Type ValveASystem 212 Y@ Weld CIL 0.83 Examination Box length 1500 Weld length (Actual) 28.50 Loss Volume Data. "InmajoiLy of hmnations arc those anrioutea to OD contigu r~uor sucin as tapers, hoop s5.nnka c ana oeri .,"00 p3f1 configurauon. Thus resulting in ýrignt sode tnanGie or rectarg*e stapes'" of lo,;s coveiage. These common geometric shapes wil be used for Oetermining volumes that have not been examined.

Code Required Volume 11.8 cubic inches Insertl 1"for each Determinina volumes loss due to limitation - all dimensions are In Inches Data Sht 0 Axial Scan Identifier Scan Lenath Depth Multioll Weld Lenoth Loss Volume 45 SW Dnstream 0 0.28 0 28.5 0.00 45 SW Upstream 1.5 0.28 1 28.5 11.97 70 RL Dnstream 0 0.28 0 28.5 0.00 70 RL Upstream 1.5 0.28 1 28.5 11.97 0 0.28 a 28.5 0.00 45 SW Dnstream 1.5 0.28 1 5.5 2.31 70 RL Dnstream 1.5 0.28 1 5.5 2.31 0 0.19 0 28.5 0.00 0 0.19 0 28.5 0.00 0 0.19 0 28.5 0.00 0 0.19 0 28.5 0.00 0 0.19 0 28.5 0.00 Clrc Scan Identifier Length Deoth Multioller Weld Length Comments 45 SW Clockwise 0.75 0.28 1 28.5 45 SW Counter Clockwise 0.75 0.28 1 28.5 0 0 0 28.5 0 0 0 28.5 0 0 0 28.5 0 0 0 28.5 0 0 0 28.5 0 0 0 28.5 Total Number of scans 6 Total Aggregate Volume 70.965 Total Aggregate Volume of Loss Coverage in cubic inches in cubic inches Resultant loss coverage in % Select which coverage applies ExaminationCoverage obtained X ASME Code Coverage GEH Procedure Coverage Page ¢ of 7 G- Prepared By: , J': Customer Reviewed By:_

Date: _ I 17--1ZI t Date:

Report1R c N.16, ZJ Wall Thickness Site: Oyster Creek Unit: 1_RprN H1IITACHI IP tR24-166rR Profile Sheet Project 0C1R24 4th Interval/3rd Period 1.*5" 1*

1.5"

System: 212 Component ID Number: NZ-3-0052 Crown Height: .05 Crown Width: 1.0 UPST Component: DNST Component:

Nominol Diameter: 8 Weld Length: 28.5 FLOW*

VA&e -FLcý4 ý 7-u-Tray Huhe Initials: Drawn by: Level: Dote: GE Reviewed By: Level: Dote: Utility Review Dote: . ANI Review:. Date:

Page Z of 7

Report No.:

Wall Thickness I

Site: Oyster Creek Unit I HITACHI 1R24-168 Profile Sheet Project OCIR24 I 4th Intervaol/3rdPeriod System: 212 1.5" Position 0. 90° 180° 270O Component ID Number: NZ-3-0056 1.5"

-Ib, [11

-~

EL E1-1 N/A N/A N/A N/A Crown Height .05 2 N/A N/A N/A N/A Crown Width: 1.00 Vakve Elbow 3 .67 " N/A N/A N/A UPST Component DNST Component Nominol Diameter: 82 4 .495 N/A N/A N/A Weld Length: 27.25 "

5 .49 " NIA NIA NIA FLOWD ICN I-

4--

11/6/2012 eiwd y e to 11 l:(Dote

, .,v Chad Olson 11 C/ / 7)

Initials: Drawn by: Level: Dote: GE Reviewed BY. 6 *~ Dote: Utility Review: Dote: ANII Review: Date:

Page Z of

UT Volumetric Coverage Station Creek Unit.

HITACHI Calculation Form Component Number:

Reprt Number:

NZ-3-0070 1R2 Date. 11/11/2012 Coverage Calculations Weld Insoection Data Confiouration: Valve to TEE Weld Type Single Sided DieameterlNom): 8" Limitation Type V e system 212 Y (a Weld CIL 0 Examination Box length 1.300 Weld length (Actual) 27.50 Loss Volume Data. Tne rniajo!r'jo liiat riraonri a~a 111- UX.W.1,to Ga Cz. ~italln S'-Lt tic.~s.hopIr uno omo.r GDpa configuraton. Thus resulting in 'ngnt sio. tftangi. or rectangie snrpes" or iass coverage. These common geormenc sniapes will be used tor determining volumes that have riot been examined Code Required Volume 7.2 cubic inches Insert "1" for each ueianmnUU1W.n uuuams uw miun- all uiiiuiiaiuii MIA11mm11011 ais-L Data Sht # Axial Scan Identifier Scan Lenath Depth MutJli 3ll Weld Lenoth Comments Loss Volume 45 SW Dnstream 0 0.20 0 27.5 0.00 45 SW Upstream 1 1.3 0.20 1 27.5 7.15 70 RL Dnstream 0 0.00 0 27.5 0.00 70 RL Upstream 1 1.3 0.20 1 27.5 7.15 0 0 0 27.5 0.00 45 SW Dnstream 1 1.3 0.2 1 5.0 1.30 70 RL Dnstream 1.3 0.2 1 5.0 1.30 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0.00 C>

0 0 0 27.5 0 0 0 27.5 0.00 Clrc Scan Identifier Lenath Depth Mulipe Weld Lenoth Comments LOss Volume 45 SW Clockwise 0.65 0.20 1 27.5 3.58 3.58 45 SW Counter Clockwise 0.65 0.20 1 27.5 0.00 0 0 0 27.5 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0 0 0 27.5 0.00 Total Number of scans 5 Total Aggregate Volume Total Aggregate Volume of Loss Coverage MA-in cubic inches in cubic inches Resultant loss coverage in %1 56.06% Select which coverage applies Examination Coverage obtainedI 4 X ASME Code Coverage GEH Procedure Coverage Page a of 7

." Prepared By::l Customer Reviewed By:

V Date:_____ 11-- Date:

Report NoN*

Wall Thickness Site: Oyster Creek Unit I I1TACH I 1R24-169 Profile Sheet Project 0C1R24 4th Interval/3rdPeriod System: 212 Component IDNumber: NZ-3-0070 Position 0° 900 180' 2700 2 4I 1 .71 N/A N/A N/A Crown Height Flush 2 .52 N/A N/A N/A Crown Width: .80 Tee Valve 3 .60 N/A N/A N/A UPST Component: DNST Component Nominal Diameter:

4 .65 N/A N/A N/A Weld Length: 27.5 5 .72 N/A N/A NIA FLOW" VW L-vj e -T:7LOC,_,ý Iýz Troy Huhe 11 111812012 G R Iel It.Da.te Drown by: Level: Dote: GE ReviewedBy Level: Date: Utility Review: Date: -ANII Review: Date:

Page Z of'

Unit: 1 Report N ..

1R24-170';4 Wall Thickness *m Site:

Oyster Ce

~h'I~ITACH I Profile Sheet I Project 4t.5"

.CIR24 rv~ d i System: 212 Component ID Number: NZ-3-0076 Crown Height Flush Crown Width: .70 UPST Component: Valve DNST Component Nominal Diameter:

I Weld Length: 27.5

--.FLOW 1LV1/4.

FWcw \J A,ýý C-

_7 *L L Troy Huhe H0 Dote: ii, Review Dote: ANINReview. L/ Dote:

Initials: Drawn by: Level: Date: GE Reviewed By:VLveI:

Page 2of i.

C'..

Station:i yster Creek UT Volumetric Coverage Unit: I HITACHI Calculation Form Component Number:

Report Number:,

NZ-3-0077 1R24-171 Date: 11/11/2012 Coverage Calculations tWeld Insoection Data Configuration: Valve to TEE Weld Type Single Sided Diameter(Nom: 8a" Limitation Type V System: 212 Y"Q Weld C/L 0 Examination Box length 1.200 Weld length (Actual) [ 7.50 Loss Volume Data. Tne majoiiy of limitaons are those attributed to OD corfmi.;iaon sucl as tauts r,oop smizn e and omner OD Pan contigurahon Thus resulting in 'ngnt syoe tiangie of rtctangl1 shapes" of loss coverage. These common geometric shapes willbe used fot determning volumes that have not buen examined Code Required Volume 6.1 cubic inches Insert "1" for each Determining volumes loss dun to limitation - all dimensions Are In Inrhes

...... f,,,,--'rt"... ................. T"Y "" ,T,'l'f,'lr'lr Scan Data Sht N Axial Scan Identifier Comments Loss Volume 45 SW Dnstream 0 0.18 27.5 0.00 45 SW Upstream 1.2 0.18 1 27.5 5.94 70 RL Dnstream 0 0.18 0 27.5 0.00 70 RL Upstream 1.2 0.18 1 27.5 5.94 0 0.18 0 27.5 0.00 45 SW Dnstream 1.2 0.18 1 5.0 1.08 70 RL Dnstream 1.2 0.18 1 5.0 1.08 0 0.19 0 27.5 0.00 0 0.19 0 27.5 0.00 0 0.19 0 27.5 0.00 0 0.19 0 27.5 0.00 0 0.19 0 27.5 0.00 CIrc Scan Identifier Le~nJoth Denth Mu'iioll' Weld Length Comments LOss Volume 45 SW Clockwise 0.8 0.18 1 27.5 2.97 45 SW Counter Clockwise 0.8 0.18 1 27.5 2.97 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0 0 0 27.5 0.00 0 0 0 27.5 0.00 Total Number of scans 6 Total Aggregate Volume 3 Total Aggregate Volume of Loss Coverage 'U' in cubic inches in cubic inches Resultant loss coverage in %1 55.04% e Select which coverage applies ExaminationCoverage obtained X ASME Code Coverage GEH Procedure Coverage Page > of 7 DPrepared By: - Customer Reviewed By:

- ~Date: I11-*11 2- Date:

Unit: Report NoV Wall Thickness Site: Oyster Creek 1R24-171 Q)-M TACHI Profile Sheet Project 0C1R24 4th Interval/3rd Period System: 212 Component ID Number: NZ-3-0077 1.5"1.5" Position 0° 90° 180° 2700 Ell R fl 1 .67 N/A N/A N/A Crown Height Flush 2 .53 N/A N/A N/A Crown Width: .7 3 .55 N/A N/A N/A UPST Component DNST Component Nominol Diameter:

4 .49 N/A N/A N/A Weld Length: 27.5 5 .49 NIA NIA NIA FLOW"

\/Iwg 12wZ--

L1 11/8/2012 L -**d6 . ..~

7nti Initials:

Troy Huhe Drown by: Level: Date: IGE ReiwdB Level: Dote: Utility Review: Date: .. -ANII Review. Date:

Page z- of 7

Report N\q 4 0 Wall Thickness Site: Oyster Creek Unit HITACHI 1R24-172 Profile Sheet Project: 0CIR24 L- -------------I 4th Interval/3rdPeriod System: 212 Component ID Number: NZ-3-0081 "1.5" Position 0. 90 180' 270° 1 .48 N/A N/A N/A Crown Height Flush 2 .45 N/A N/A N/A Crown Width: 1.0 PIValve 3 .54 N/A N/A N/A UPST Component DNST Component Nominal Diometer:

4 1.0 N/A N/A N/A Weld Length: 27.5 NIA NIA N/A 5 NIA FLOW~

T-LQCý-4 V&L\,c Troy Hyhe It 111812012 Drawn by: Level: Dote: GE Reviewed B'. Level: Date: t~i

ýtyReview. Date: ANII Review: Date:

Page of

Station: Oyster Creek UT Volumetric Coverage Unit:

r6 HITACHI Calculation Form Component Number:

Report Number:

1R24-192 RF-2-0115 Date: 11/19/2012 Coverage Calculations Weld Inspection Data Confinuration: Vavle to Pipe Weld Type Dual Access Diameter(Nom): 18" Limitation Type Confi System: 422 Y @ Weld C/L Examination Box length Weld length (Actual) Loss Volume Data. The n.uo;, of .rn~rubOIl arv tli,*u ,IttID.Avu a CD .. ",liun v*Gn as ..efs. hOup s r :nd Gird C. paa connigurai.an Thus resulting in'rignt slde triangle of rectangle shapus" of loss coverage These commoni geometric shapes will be used for dletemininng volumes that have not bern exanined Code Required Volume 30.4 cubic inches Insert "1"for each r*at.a*i*ln* u^hma= I^ee *,l,,a (,^ Ilmi4"a)l^* --- --.- I--

Qeks in na vo unnes oss Hue w maggon - a mians ons gie ... ...-

Data Sht # Axial Scan Identifier Scan Lenth Depth Multiplier Weld Lenath Comments Loss Volume 45' Scan UPS &DNS 0.6 0.80o 0.5 57 2 Configuration Loss 10.3 1.6 0.333 1 10.2 Attachment Loss 5.4 0 0 0 10.2 0.0 0 10.2 0 0 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 Clrc Scan Identifier Lenohe Ooth jutt Weld Length0 Comments Loss Volume 45 SW Clockwise 0 0 0 10.2 No Loss 0 45 SW Counter Clockwise 0 0 0 10.2 No Loss 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 10.2 0 0 0 0 1 10.2 0 Total Number of scans Total Aggregate Volume 1 "1. Total Aggregate Volume of Loss Coverage M.'

in cubic inches in cubic inches Resultant loss coverage in %Select which coverage applies ExaminationCoverage obtainedI 7.0 I X ASME Code Coverage GEH Procedure Coverage Page $ of(

Prepared By::, , Customer Reviewed By:

Date: 0-J ff. I?- - Date:

HITACHI Wall Thickness Site: Oyster Creek Unit I Report Noa" Profile Sheet Project: 0C1R24 1R24-192 r==m System: 422 Component ID Number: RF-2-0115 1.5"

1.5" Position 0. 900 180' 2700 1 NIA N/A N/A N/A 01 2 4 Crown Height 0.05",

2 N/A 1.05" N/A N/A Crown Width: 1.10"*

Valve Pp 3 NA 1.00" N/A N/A UPST Component: DNST Component:

Nominal Diameter: 18.0"'

4 N/A 1.10" N/A N/A 5 N/A [ N/A INIA N/A Weld Length: 57.0"

-FL-OW-0 (CxJr--&A&l& 'RO-r

-4' Cie Paul! Valden 11 11117/2012 Dote: ,-ANII Reviewr. Date:

49 Page 2 of 6

Wall Thickness (6iI Profile Sheet 1.511 Crown Height: 0.05"1 Crown width: 0.90" PIPE VALVE UPST Component: DNST Component Nominal Diameter:

Weld Length: 27.4" 0 ~

-7

~-1 60 (1ý-6 C7r414:6j /::-40/' &.Vlok/jS 647-a (Qu

,<46le!d /Z -r ý 4 - -) z ý j ý f- P re , 6 1-',1- zc<)o

Unit ReportN.

Wall Thickness Site: Oyster Creek H1IITACHI 1R24-199 Profile Sheet Project 0CIR24 4th Interval/3rdPeriod System: 212 Component ID Number: V-1-173 EMRV Position 0. 90° 180° 270° 3 2 El S15" 1 1.43 N/A N/A N/A 4~

Crown Height 0.15"_

2 1.43 N/A N/A N/A Crown Width: 1.50' Valve Flange 3 1.55 N/A N/A N/A UPST Component: I DNNST Component:

Nominal Diameter: 12 4 N/A N/A N/A N/A Weld Length: 37.75 5 NIA NIA NIA NIA FLOW 4(L KJ.~

46-- - = V -I- ^i3

£tl,?V V-1-T173 Jack Reisewitz II 11111/2012: * -

Initials: Drown by: Level: Date: GE Reviewed By: Level: Date: Utility Review: Dote: ý-"Nl Review. Dote:

Page 1. of(

Wall Thickness Profile Sheet Crown Height: .05 in Crown Width: 2.0 in Hemi Head Nozzle UPST Component DNST Component Nominal Diameter: 8.0 in Weld Length: 29.5 in P

ý,Tj-"

Wall Thickness HITACHI Profile Sheet System: 211 Crown Height: .05 in Crown Width: 2.2 in Nozzle Hemi Head UPST Component: DNST Component Nominal Diameter: 12.0 in Weld Length: 42.5 in a

N Aj 0;V 1Z

v t e Letter Sequence Request
TAC:MF3406, (Open)
Initiation Request Acceptance Administration Questions 17 September 2014 6 January 2015 Answers 29 January 2015 14 November 2014 Results Approval... Other: ML15097A153
MONTHYEAR2014-09-17 [Table View]

RA-14-001, End of Interval Relief Requests Associated with the Fourth 10-Year Inservice Inspection (ISI) Interval: Difference between revisions

Latest revision as of 23:45, 5 February 2020

Text

Subject:

Attachment:

Reference:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment:

Description:

Attachment: