ML15082A163

From kanterella
Jump to navigation Jump to search

Response to Request for Additional Information - End of Interval Relief Requests Associated with the Fourth 10-Year Inservice Inspection (ISI) Interval
ML15082A163
Person / Time
Site: Oyster Creek
Issue date: 01/29/2015
From: Jim Barstow
Exelon Generation Co
To:
Document Control Desk, Office of Nuclear Reactor Regulation
References
RA-15-012
Download: ML15082A163 (49)
v • d • e


Text

RA-15-012 January 29, 2015 10 CFR 50.55a U.S. Nuclear Regulatory Commission ATTN: Document Control Desk Washington, DC 20555-0001 Oyster Creek Nuclear Generating Station Renewed Facility Operating License No. DPR-16 NRC Docket No. 50-219

Subject:

Response to Request for Additional Information - End of Interval Relief Requests Associated with the Fourth 10-Year lnservice Inspection (ISi)

Interval

References:

1) Letter from J. Barstow {Exelon Generation Company, LLC) to U.S.

Nuclear Regulatory Commission, "End of Interval Relief Requests Associated with the Fourth 10-Year lnservice Inspection (ISi) Interval,"

dated January 7, 2014

2) Letter from J. G. Lamb (U.S. Nuclear Regulatory Commission) to M. J.

Pacilio (Exelon Generation Company, LLC), "Oyster Creek Nuclear Generating Station - Request for Additional Information Regarding the Fourth 10-Year Interval lnservice Inspection Program Plan Requests for Relief {TAC Nos. MF3406 and MF3407)," dated September 17, 2014

3) Letter from J. Barstow (Exelon Generation Company, LLC) to U.S.

Nuclear Regulatory Commission, "Response to Request for Additional Information - End of Interval Relief Requests Associated with the Fourth 10-Year lnservice Inspection (ISi) Interval," dated November 14, 2014

4) Letter from J. G. Lamb (U.S. Nuclear Regulatory Commission) to M. J.

Pacilio (Exelon Generation Company, LLC}, "Oyster Creek Nuclear Generating Station - Request for Additional Information Regarding the Fourth 10-Year Interval lnservice Inspection Program Plan Requests for Relief (TAC Nos. MF3406 AND MF3407)," dated January 6, 2015 In the Reference 1 letter, Exelon Generation Company, LLC {Exelon) requested relief from the American Society of Mechanical Engineers {ASME) Boiler and Pressure Vessel

{B&PV) Code,Section XI, "Rules for lnservice Inspection of Nuclear Power Plant Components." These reliefs apply to the fourth 10-year lnservice Inspection (ISi) interval, which concluded on January 14, 2013, for the Oyster Creek Nuclear Generating Station.

The fourth 10-year ISi interval complied with the ASME Boiler and Pressure Vessel Code,Section XI, 1995 Edition with 1996 Addenda.

U.S. Nuclear Regulatory Commission End of Interval Relief Requests Associated with the Fourth lnservice Inspection Interval January 29, 2015 Page 2 In the Reference 2 letter, the U.S. Nuclear Regulatory Commission requested additional information. Our response was contained in Reference 3. In the Reference 4 letter, the U.S. Nuclear Regulatory Commission requested additional information. Attached is our response.

There are no regulatory commitments in this response.

If you have any questions concerning this response, please contact Tom Loomis at (610) 765-5510.

Respectfully, James Barstow Director - Licensing & Regulatory Affairs Exelon Generation Company, LLC

Attachment:

Response to Request for Additional Information cc:

Regional Administrator, Region I, USNRC USNRC Senior Resident Inspector, OCNGS Project Manager [OCNGS] USNRC

ATTACHMENT Response to Request for Additional Information

ATTACHMENT Response to Request for Additional Information Page 1 By letter dated January 7, 2014 (Agencywide Documents Access and Management System (ADAMS) Accession No. ML14028A579), as supplemented by letter dated November 14, 2014 (ADAMS Accession No. ML14321A044), Exelon Generation Company, LLC (Exelon or the licensee) submitted Requests for Relief R-44 and R-45 from the requirements of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code,Section XI for Oyster Creek Nuclear Generating Station (Oyster Creek). The requests for relief apply to the fourth 10-year inservice inspection (ISi) interval, in which the licensee adopted the 1995 Edition through the 1996 Addenda of ASME Code Section XI as the code of record.

The U.S. Nuclear Regulatory Commission (NRC) staff has reviewed the Relief Requests R-44 and R-45, and has determined that a request for additional information (RAI) is needed to complete its technical review. The NRC staff's RAls are below.

Request:

1) The examination limitations for ASME Code,Section XI, Examination Category B-F, Item B5.11, weld NR02 4-565D, N1 D Recirc Outlet Nozzle-to-Safe End, is discussed in the licensee's RAI response dated November 14, 2014. Attachment A40 to the licensee's submittal dated January 7, 2014, contains a sketch of this weld. However, this sketch appears to be a drawing of a cladded nozzle "set-in" design weld rather than a nozzle-to-safe end weld. Please clarify this sketch or provide another sketch clearly indicating the Item B5.11 nozzle and the safe end components. Please include cross-sectional plots showing volumetric coverage obtained with specific volumetric coverages near the inner surface, using appropriate ultrasonic wave angles and modalities. These are typically the most highly stressed regions, exposed to operating environments where service degradation would be expected to occur, should it be manifested.

The photos provided in the original submittal in Attachments A30 and A40 for the Item B5.11 welds are indecipherable. Please provide replacement images that are clear or alternative information to clarify the limitations these photos were intended to represent.

Response: contains the Examination Summary Sheets for welds NR02 4-565D (A40 in the Reference 1 submittal) and NR02 2-567A (A30 in the Reference 1 submittal). No photos were provided in Attachment A30 of Reference 1; however, the Examination Summary Report is provided.

Request:

2) For R-45, Examination Category B-J, Item B9.11 welds NE 5-0002, NE 5-0022A, and NG-5-D-0002, shown in Figures 2, 3, and 4, respectively, please provide cross-sectional plots showing volumetric coverage obtained with specific volumetric coverages near the inner surface, using appropriate ultrasonic wave angles and modalities.

Response: contains the Examination Summary Sheets for welds NE 5-0002, NE 5-0022A, and NG-D-0002 (Note: NG-D-0002 is the correct designation for this weld).

Examination Summary Sheets for Welds NR02 4-5650 and NR02 2-567A

Report No.:

EXAMINATION

SUMMARY

SHEET 005123 GE NUCLEAR ENERGY Site and Unit:

O~ster Creek Unit 1 Component ID:

NR02 4-5650 {N10}

Outage:

OC1R20 NOZZLE to SAFE-END System RPV ASMECat.:

8-F ASMEltem 85.10 Aug Requirements:

NIA Exams Performed Data Sheet Cal Sheet Procedure Calibration Block Examination Cert Level Date Personnel 45° / RL NIA APC-007 GE-UT-245N1 INV-185A Andre' Rachal II 02-NOY-04 45° /S NIA APC-008 GE-UT-245/V1 INV-185A Andre' Rachal II 02-NOY-04 60° / RL NIA APC-012 GE-UT-245/V1 INV-185A Yoshi Sekinuma Ill 02-NOY-04 60° / RL NIA APC-009 GE-UT-245/V1 INV-185A Andre' Rachal II 02-NOY-04 45° / RL N/A APC-010 GE-UT-245/V1 INV-185A Yoshi Sekinuma Ill 02-NOY-04 45° / s NIA APC-011 GE-UT-245N1 INV-185A Yoshi Sekinuma Ill 02-NOY-04 NIA APD-002 N/A GE-UT-245/V1 NIA Andre' Rachal II 08-NOY-04 PT N1DPT N/A GE-PT-100N4 NIA Chad Olson II 07-NOY-04 Examination Results:

During the automated ultrasonic examination of weld number NR02 4-565D (N1 D), the "SMART 2000" system recorded no indications associated with IGSCC utilizing 45° -shear wave, 45° -Refracted Longitudinal wave, and 60° -Refracted Longitudinal wave search units.

This examination was performed utilizing procedure GE-UT-245, Version 1, due the presence of OD and ID deposited corrosion resistant cladding (CRC).

- The 45° -shear wave examinations were performed from both the upstream and downstream sides of the weld, and recorded inside surface geometry, beam redirect and non-relevant indications.

- The 45° -RL wave examinations were performed from both the l4>Slream and downstream sides of the weld, and recorded inside surface geometry, interface, shear component and norrrelevant indications.

- The 60° -RL wave examinations were performed from both the upstream and downstream sides of the weld, and recorded shear component and non-relevant indications.

Downstream examinations were limited due to the Nozzle to Safe-end configuration. All scans were limited due to incomplete machining of the CRC on the OD surface. Machining of the OD surface CRC stopped near the weld centerline, and left a step approximately 0.020" to.040" in height. Reference the photo on page #19.

This examination satisfies the requirements of ASME Section XI, 1995 Edition, 1996 Addenda, and GL 88-01.

This component was examined following the guidelines of the POI document titled "Guideline for Ultrasonic Examination of Corrosion Resistant Cladding (CRC)", #PDl-GL-002, ReviSion "B" Dated January 29, ~~ Ultrasonic examination coverage requirements of Procedure GE-UT-245 were not achieved due to the geometrical configuration of the component. Coverage calculations were performed using ASME Sec XI, Appendix VIII, Supplement 10 as a base qualification for the examinations. The examination requirements of Supplement 10 are more stringent than those of Appendix Ill. Approximately 70% of the full-volume cmerage was achieved in accordance with the requirements of Supplement

10.

A liquid penetrant examination was performed prior to the ultrasonic examinations, which resulted in no recordable indications.

Previous ultrasonic examination data, reports, and drawings were reviewed prior to this summary.

Summary numbers: Auto UT-005123, PT-005122.

Ev.amination results were compared to data report R-16R-028 from 16R outage with

~ No Change These exarrinafions were performed under Worlc Order:

C2007460 D

Change This Summary and the folowing data sheets have been reviewed and accepted by the folowing personnel:

jjjz~

/1-9-P~ __...,,\\0 ~

11-1~-D'{

~"~ ~~

itle:

Date:

~~

Page 1

of 19 Reviewed By:

Level:

Date:

ANll Reviewed By:

Wall Thickness 11 Site:

QliTERCREEK Unit:

1 I

Report No.:

GE NUCLEAR ENERGY I I Profile Sheet Project:

HlJl§

~

I

~

c ~

System:

Bat I

NR02 HHD fNtDJ Component ID Number:

((]

Poeltion I o*

I 90*

I 1ao*

I 210*

I

[I]

~

rn

~

I 1.600" NIA NIA

~

Crown Height:

EJJmi 2

I 1.4'0" NIA NIA

'.A Crown Width:

1.r I

NQWE

\\;/

SAF~:f.t:l.12 I

NIA I

NIA I

DNST Component:

3 I 1.4'0" I NIA UPST Component:

Nominal Diameter:

~

4 I 1.840" I NIA I NIA I NIA I Weld Length:

w.:

I FLOW....

5 I UflO" I NIA I

NIA I NIA I 60° RLl 60° RL 60°.RL 60° RL

  • 45°RL
  • 45° RL 45° RL 45° RL 4s0 *s 45°S 45° s 411;0 ~

45°$, 45°'RL'i.6Cl 0R.L Supplement W E.xaltllnaijon Coverage Thickness Taken fr9m.. 1996 D$ta

~

PIUIJobasoo

~Exa

~

i:I' Ul

.Qi~

Level:

Date: I GE Reviewed By:

Page 02 of.1.i

~~~~~~~~-~~~~~~-'"-~~~~~~~~~~~~~~~~~~~__:G=-=-ENuc~arEnergy 45° Shear - General OVE!rview - (LKDN)

NR02 4-5650 (NlD)

' " "'"Vu*w ;>.;>1)1 t jllflNID... llJ

~-*~

fi11

"'" '"'" A1MIY" Nlll.r.. t I.1ym1t : At1<1fy<,1"]

~::.~~-:§Cf

SUMMARY

NUMBER: OO!illl NOZZLE TO SAFE-END

~~

.....aJjg PageJof ~

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~---'G'-ENuc~arEnergy lmnnVww /.i'l)l-1 jlltlNlf);'/ 11

~

JI 45° Shear - General OvE~rview - (LKUP)

NRQ2 4-56_50 (NlD)

D18i 111111iiM'4*m+;fom*@fl*

, *'\\*;;-: ~

  • [2"'"*

r*~,.. :-.....

_----~

"l

&14..""'

    • ~ :.......

~

SUMMARY

NUMBER: QQ!il.Zl NOZZLE TO SAFE-END

~,ij

..aJ~

Page~ of li

~~~~~~~~~-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~G~E_NuclearEnergy 45° RL - General OverviE~w - (LKDN)

NR02 4-5650 (NlD)

NOZZLE TO SAFE-END ti '-t'l11p: A11.1ly'l<oNIO.r

    11)1-1 I 1111N1 l)/;.>111pl8J i!ii;.@§ NR02 4-5650 (NlD) nnnn.-~

    SUMMARY

    NUMBER: QQ!il2l Page 2of12

    ~~~~~~~~-~~~~~~~~~~~~~~~~~~~~~~~~~~__:;G~ENuclearEnergy 60° RL - General OverviE~W - (LKDN)

    '"""'Vu*w /.,'1)1-4 liUl~lll/111 r

    1. iii!¥@f#

    SUMMARY

    NUMBER: OO:illl NR02 4-5650 (N10)

    NOZZLE TO SAFE-END

    .iJ..i..?SJ

    ..J.4J..?SJ Page Z of li

    GE Nuclear Energy

    ~~~~~-~~~_:__~~~~~~~~~~~-----

    l11111t1Vll'w ;>./I.II I lllllNl()/ ;>11 60° RL - General Overvh~w - (LKUP)

    ~?

    14i"'W NR02 4-5650 (NlD)

    " *:.~~.,_r

    ... "'-~~~* 11:* '.

    t~

    q

    SUMMARY

    NUMBER: QQ!illl Page.a of 12

    Ultrasonic Data I Scan Parameter Sheet GE Nuc/1ear Energy (Automated with Micro TomoScan)

    Site:

    Ovster Crulc Procedure:

    fl.~:f.!.[*Z.4.§.

    System:

    Bf!)L Report No.:

    Qgj1ZJ.

    Unit:

    1 Version I Revision:

    ~

    Weld No.:

    t:f.89.Z. ~§§§.12 lN.112l Data Sheet No.:

    APQ.O(U Project No.:

    Hl9§ ORR:

    tfA Configuration:

    NOZZLe. [Q §A.Eli:&t:f.Q Calibration Sheet No.:

    A.PC.OOZ tlmJ. gj_z Scanner Information Weld Reference, (GE-ADM-1005): Lo:

    [OP DEA.Q r;e_NTER Wo:

    ~e.L.12 CL Motor Steps:

    Cir:

    1H.§ Tra:

    Z§.QZ Examination Surface:

    QJ2 Exam Surface Temperature:

    l!l *F Thermometer SIN:

    mm Exam Start:

    gz-ti!lY~ §.:Z.§.;oo eM.

    Exam End:

    08-Nov-<U l.;~l.:OO AM Nominal Pipe Size:

    ~ N1)minal Thickness:

    1...§JL Weld Width:

    1..§!L Weld Length:

    ~

    Scanner:

    ttm!A Track Diameter:

    l§JJ!L.

    Arm Length:

    1JJl!L.

    Track Location:

    QQWN§TREA.M X Positive Scan Direction:

    QQMtl.ffie.AM Y Positive Scan Direction:

    &W I

    Resolution:

    s~

    lnd*~x Ax I Clrc:

    s w.r.

    s~

    Axial Scan Speed:

    s M.laL~

    Clrc Scan Speed:

    s 1.Q la.LSec, Scanner Zero Positions:

    CIR:

    me DEA.12 r;e.NTEB.,

    TRA:

    WEl.Q f;EN[gRLttte.

    ROT Zero:

    LQQKltl.fl. QQWN§'[B&AM Scan Parameters and Results Scan:

    Skew:

    Filo ID:

    Disk:

    X-Start:

    X-Stop:

    Y-Start:

    Y-Stop:

    Gain:

    Results:

    Comments:

    Z1ll Q

    BBIJ.U2.Z1.Q S2K-D"""4.00§.

    rut:

    1.§,£.

    ~

    ~

    LQa C.O.E,J.K 46°§.. 4.§."Rt... §Q0 LKDN ZZQ 1JQ BBN.1..QlZ!J.

    S2K-D~Q£00§.

    rut:

    .u.I:

    Q,.Q'.'.

    z.£.

    LQa C.O.E,J,K 4.§.~. 4.§.

    08.L, §~ LKJ,lp ml

    .IQ BBN.1.Dm

    §2K-D"""4.006

    ~

    1..£.

    Q,.Q'.'.

    .H..§'.'.

    L.Qg

    ~

    46"S. 4.§.0Bt... §Q 0 LKCW DNS[

    w.

    .IQ BBN.112W.

    §2K-0"""4.00§.

    Q,.Q'.'.

    ~

    Q,.Q'.'.

    1§£ L.Qg

    ~

    46°§, 46~1... §Q0 l.~tt: J,LPS[

    Z4.Q

    lQ BB/j1..lmQ

    §2K-D"""4.00§.

    ~

    1..£.

    Q,.Q'.'.

    .H..§'.'.

    L.Qg

    ~

    46°§., 4.§.

    0RL, §~ LKf;'H! DN§.l ro

    lQ BB!i!Ql4.1 S2K-D"""4.00§.

    11..§£

    1Jl:

    Q,.Q'.'.

    .u&:

    LQa

    ~

    46°§.. 4.§..08.L, 80° LKCf;tt: f.LP§.T

    !;MMlt:l8I!Qt:I BfiiSULI§ L&!:lliit:ll2 A - NO RECORDABLE INDICATIONS B - NON-GEOMETRIC INDICATIONS C *NON-RELEVANT INDICATIONS D *ACOUSTIC INTERFACE E

    • INSIDE SURFACIE F *OUTSIDE SURFACE G - WELD DISCONTINUITY H
    • ROOT GEOMETRY I
    • COUNTERBORE J *SHEAR COMPONENT K
    • BEAM RE-DIRECT All scans were limited due to the presence of an incomplete CRC machining of the OD surface. Machining of the OD surface CRC stopped near weld centerline, and left a step approximately 0.020" to.040" In height. Reference the photo on page ~119.

    ~~~ /"7 I

    i~

    -,, ~' CJ

    ~~

    725 11/DLo?

    Andre' Rachal II 08-Nov-~

    ANll Review: /

    , Date:

    Examiner:

    Level:

    Date:

    Level:

    Date: ""'

    Utility Review:

    Date:

    Page ll of.l!

    GE Nuclear Energy

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Scan Information Sheet Component ID: NR02 4-5650 (N1D)

    NOZ-SE INV-185A Transducer Parameters:

    Calibration Measured Transducer Pulse Angle Size Freq.

    Model Exit Point SIN Scan Mode Width MHz AX 45°RL 250ns 45*

    2(15X25)mm 2.00 RTD 0.80"04-319 AX 45° Shear 333ns 45*

    24X 17 mm ERip.

    1.50 RTD 0.55"98-159 AX 60" RL 250ns 60" 2(15X25)mm 2.00 RTD 0.75".03-675 CIRC 45° RL 500ns 45*

    2(15X25)mm 1.00 RTD 0.75"04-331 CIRC 45° Shear 333ns 45*

    24 X 17 mm Ellip.

    1.50 RTD 0.55"98-158 CIRC 60° RL 500ns oo*

    2(15X25)mm 1.00 RTD 0.75"04-336 Scan Information:

    Temp Gauge S/N:

    235195 Component Temperature:

    90 °\\ F Scan Size Index ~ize

    ~

    Disk #

    Scan

    ~

    .EkJQ Start stnn Start stnn Scan Index S2K-D-04, 05 45°RL LKDN O"

    RRN1DZ10

    -4.60"

    -.30" O"

    86.5" O"

    O" S2K-D-04, 05 45°S LKDN O"

    O"

    -2.60" S2K-D-04, 05 OO°RL LKDN O"

    O"

    -5.30" 0

    S2K-D-04, 05 45°RL LKUP 180° RRN1DZ20 O"

    2.40" O"

    86.5" O"

    o*

    S2K-D-04, 05 45°S LKUP 180" O"

    -2.60" S2K-D-04, 05 OO°RL LKUP 180" O"

    -5.30" S2K-D-04, 05 45°RL LKCW (UPST) 90" RRN1DZ30 O"

    86.5" 3.10" 1.40" O"

    O" S2K-D-04, 05 45°8 LKCW (UPST)

    -45"

    -2.60" O"

    S2K-D-04, 05 60°RL LKCW (UPST) 90"

    -5.30" O"

    S2K-D-04, 05 45°RL LKCW (ONST) 90*

    RRN10Z31 O"

    86.5" O"

    -3.0" O"

    O" S2K-D-04, 05 45°8 LKCW (0NST)

    +45"

    -2.60" O"

    S2K-D-04, 05 60°RL LKCW (DNST) 90"

    -5.30" O"

    S2K-D-04, 05 45°RL LKCCW (UPST)

    _900 RRN1DZ40 O"

    86.5" 3.00" 1.40" O"

    O" S2K-D-04, OS 45°S LKCCW (UPST)

    -45"

    -2.60" O"

    S2K-D-04, 05 OO°RL LKCCW (UPST)

    -90*

    -5.30" O"

    S2K-D-04, 05 45°RL LKCCW (ON8T)

    -90" RRN1DZ41 O"

    86.5"

    -.54"

    -3.0" O"

    O" C'lV.nJ\\;I (lc;:

    45°S LKCCW (DNST)

    +45.

    -2.60" 0-S2K-D-04, 05 60°RL LKCCW (ONST)

    -90°

    -5.30" 0-Pagel.O of 12

    ~-=~;;;...:;...,;;..q:==-_:;;;=-~~~~~~-Date:~l~l-~l~S~*~O~t~-

    //k~fef I

    GE Nuclear Energy Scanner Information:

    Scan (X axis) start: CS/INC. INTERFACE Positive Scan Direction: Downstream Index {Y axis) start: Datum "O" ((I) Too Dead Center Positive Index Direction: Clockwise Track Diameter - 28" Scanner Arm Lenath -18" Nominal Pioe Size: 26" Cal Block "r 1.80" Weld Crown Width: 1.60" (includes butterina)

    Como. Min\\Max = 1.48" / 1.66" Resolution: s; 0.036" Track position: Downstream Index: Ax Scan: s; 0.170" ; Circ Scan: s; 0.050" Track Bolts from bottom of SE Taper= -8.0" Max Scan Soeed Settings: Axial Scans - < 1.5" I Sec.

    Circ. Scans - < 1.00" I Sec.

    Comments:

    Procedure: GE-UT-245 Ver. 1 Flow is out of Vessel FULL VOLUME EXAMINATION.

    CRCWELD Surface examination IS required REPORT NO's.: 005123/UTI. 005122tPTl GE Reviewed by: --'-'-----...'----"='----------Date: //-9-tJr Page 11of12

    ~;::+~~~~---==---Date: l I- { ~

    • 0 i ANH Reviewed by: ---.1~~~£~~~~~L ___

    Date: 11 ho!Plf I

    l

    GE Nuclear Energy LIQUID PENETRANT EXAMINATION REPORT

    - site: Ovster Creek Unit 1 Project: 34705 Report Number.

    005122 Sheet No.:

    N1DPT Weld No.:

    NR02 4-565D (N1Dl Configuration:

    Nozzle to Safe.End System:

    RPV Procedure No.:

    GE-PT-100N4 VerJRev.:

    ~

    ORR:

    NIA Material:

    Surface Condition:

    Item:

    CS/SS/INC.

    Smooth Weld-Final Technique:

    Cleaner Penetrant Developer Color Contrast Solvent Removable Manufacturer Maqnaf1ux M!an.nux Maqna1Jla Tharmomaler mm Brand/Type SJCC-S

    ~

    ~

    Temperature:

    H Batch No.

    ~

    02C09K 0280JK.

    Black Light; Light Mater. NIA Blacldlght Intensity:

    lfAj/Nlarr' Pre Clean Method:

    Wiping Drying Time:

    6 llinutes

    , Penetrant Application Bnlshina Dwell Time:

    10Minutes Penetrant Removal Wipe with dry towel Drying Time:

    6Minutes Wipe with demp towel Developer Application: Spravina Developing Time:

    1Minutes Indication Number: I

    ==

    Description:==

    I Results:

    !ft I

    NRJ I

    !!111 Comments:

    QRAWING N!JM6!;,R: ~!;,-223-A2-1000

    /

    • l c-;

    Jl* *'-'* 0 c.f

    (

    Chad Ol<mn & J /\\'-

    ( -

    07-Nov-64 I~

    Date

    - ExaOl!//JI #It/#

    Level

    ~~f 1!L I~~

    G'E Review Level Date Page 12 of 19

    ULTRASONIC CALIBRATION DATA SHEET

    ~

    GE Nuclear Energy (Automated with Micro TomoScan) 1te:

    Ovster Creek Unit: 1 Project: 34705 Repart Number.

    005123 Calibration Sheet No.: APC-007 l\\Neld:

    NR02 4--5650 £N1Dl Procedure No.:

    GE-UT-245 Version:

    V1 ORR:

    NIA Instrument:

    RD Tech/f!.Tomo 11121~

    1.MU 2.2014 Manufacturer I Model Syslem Serial No.

    Acquisition Software Analysis Software Analog to Digital Convel'ter.

    RD Tech I EQn< ON Pulser/Receiver.

    RD Tech I EQn< 100 Piggy Board:

    RD Tech I EQn< 101 Manufac1urer I Model Menufadurer / Model Manufacturer I Model Search Unit Bm

    ~

    Z{,15x2§1.mm

    ~

    46°/BL FD 1.97..

    45*

    ~

    Manufacturer Serial No.

    Element Size Freq. (MHz)

    Angle / Mode FS/FD:

    MNsured Incident lo Cable:

    12JRG-61 I RG-611BQ:.174 fZJ260' {l§.' 13'

    £W Angle WedgeFtonl Type:

    Length No. ol lntermediate Connedors Calibration Standard:

    INV-116A SS/CS/INC.

    1.600..

    1.100-Serial No.

    Material Nominal Thiclcnes6 Measured Thickness Thermomet.er.

    23619fi lli "F Couplant DemlnW!f!!

    ~

    Serial No.

    Temp("F)

    Type Balch No.

    Calibration

    • A~uisition Orientation:

    ~

    CIRC Tmebase:

    dB Start: 0.000 Range:

    §.01tsln.

    iType:

    lDNOrCH IDNQTCH Units:

    Half Path Avera!jng:

    1 Depth:

    UOln.

    1.80 In.

    Digitizing Frequency:

    12.§ M.Hz Amplitude I dB:

    ~

    -1Z,5 d§ AcqLisition Rate:

    m..tH Sweep:

    1,793 In:

    t,793 la, Max Recurrence:

    ~

    Probe Gain: (dB)

    ~

    LOG Wave Mode:

    LQ!19.ltudlnal Scan offset:

    0.000111.

    Screen:

    ~

    25 dB Booster:

    Active Velocity:

    0.2272 ln.fusec.

    Index offset:

    O.OOQln.

    Offset:

    0.000 ln.lusec, Angle:

    46.00° Field Simulator: SSRomRI!§ SIN:

    CAL-RHOM-015 Wedge Delay:

    10.150 usec.

    Skew:

    ~

    Reflector:

    FARSDH NIA Configuration Max Amplitude/dB:

    -9.1 dB NIA Channel Name:

    46"RL 04-319 P1/R1 NOZ-sE Sweep:

    o.n2" NIA Pulser.

    P1 Voltage:

    300V Gain: (dB)

    LOG NIA Receiver:

    81 Width: (Ns) ~00011!

    Calibration Verification Configuration:

    Pitc/1. Catch High Pass:

    None Time Dl!te Bk><;!(

    Operator Receiver Type:

    l.gg Low Pass:

    !:/!HJ§.

    Initial 1735 02-Nov-04 INV-185A AMR Rectification:

    fHR!l/§.!

    Smoothing: 2..M!h Verffied N10 45° RL AX SCAN NOZ-St Verified 1725 07-Nov-04 CAL-RHOM-916 AMR Verified Final 1945 07-Nov-04 CAL-RHOM-916 YS

    .,A ndre' Rachal II 02-Nov-04 I

    I ( - J I'll 11,14~cd L-Initial Examiner Level Date r

    J,~

    I Date rra4~~

    .Ii1.

    //-1-&'f 1,;L.. I,J GER.

    Level Date fJit.e I Page

    ~ of

    ~

    ULTRASONIC CALIBRATION DATA SHEET l

    GE Nuclear Energy (Automated with Micro TomoScan)

    ~1te :

    Ovster Creek Unit: 1 Project: 34705 Report Number:

    005123 Calibration Sheet No.: APC-008 Weld:

    NR02 4-565D {.N1Dl Procedure No.:

    GE-UT-245 Version:

    V1 ORR:

    NIA Instrument:

    RD Tech l M.Tomo 11121-ot 1.4R1 2.2014 Manufacturer I Model System Serial No.

    Acquisition Software Analysis Software Analog to Digital Converter:

    RD Tech I EQ.TX ON Pulser/Receiver.

    RD Tech I EQTX 1flQ Piggy Board:

    BQ. Tech / EQTX101 Menufaoturer I Model Menulllcturer I Model Manufaclurer I Model Search Unit RTD 91-169 Q..fX11lmm 1.6 MHz

    ~

    ~

    450 0.66-Manufacturer Serial No.

    Element Size Freq. (M-t:Z)

    Angle / Mode FSIFO:

    Measured Incident lo RG*61 I RG-61 U l!.i.-114 250' I 26' I 3'

    ~

    Angle Wedge Front Cable:

    Type:

    Length No. ol lntermedlate Connedors Calibnrtion Standard:

    INV-115A SS / CSl llJ..C.

    L§!!C.

    ~

    Serlal No.

    Materiel Nominal Thickness Measured Thlcli:ness Thermometer:

    236116 16 "'F Couplant DemlnWatw NIA Serial No.

    Tamp ( °F )

    Type Batch No.

    Caljbration A£Quisition Orientation:

    gB!;.

    CIRC Tinebase:

    dB Start: 0.000 Range:

    6.000tn.

    Type:

    IQ.NOTgj_

    112.fJ.OTCH Un is:

    Haff Path Averaging:

    1 Depth:

    1.BO#n.

    1.BOln.

    Digitizing Frequency:

    1Z,§.Ml::a Amplitude I dB:

    ~

    • 1l,9d8 Acquisition Rate:

    262Hz Sweep:

    1,164 In.

    1,"[Mln, Max Recurrence:

    2000Hz Probe Gain: (dB) 9d8 LOG Wave Mode:

    Shear Scan offset:

    0.000 In.

    Screen:

    Il!tR1l!

    25 dB Booster:

    Inactive Velocity:

    0.1240 ln.lusec.

    Index offset:

    -Z,600 In.

    . Offset:

    o. 000 lr..!Jl§.ec.

    Angle:

    45.00° Field Simulator: SSRomll!l§ SIN:

    CAl..*RHOM-016 Wedge Delay:

    12.000 ll!ec.

    Skew:

    0.00" Reflector:

    FARSDH NIA Configuration Max Amplitude/dB:

    • 1B.6dB NIA Channel Name:

    46°5 98-169 P2 NOZ-SE Sweep:

    0.112-NIA Pulser:

    fl Voltage:

    300V Gain: (dB)

    LOG NIA Receiver:

    WA Width: (Ns) 333.000ns Calibration Verification Configuration:

    Pulse Echo High Pass: ~

    TI me Da!O?

    Rloclc Operator Receiver Type:

    l.29.

    Low Pass: ~

    Initial 1806 02*Nov41 INV-186A AMR Rectification:

    !fHR!l!ilr Smoothing: z..M!1z Verified N1 D 45° S AX SCAN NOZ-SE Verified 1126 07 *Nov41 CAL-RHOM.o1e AMR Verified Final 1941 01-Nov41 CAL-RHCJM.016 YS Ytndre' Rachal II 02-Nov-04

    ("

    I (

    /)

    ~

    lHS*Ol-1 Initial Examiner Level Date

    ~~~h/I Date ~

    f:~~

    L(-<J.,tJ'/

    lll

    //?~

    I Level Date ANll Review

    /

    /bate/

    Page 14 of 19

    GE Nuclear Energy ULTRASONIC CALIBRATION DATA SHEET (Automated with Micro TomoScan)

    Oyster Creek Unit: 1 Project: 34705 Report Number.

    005123 NR02,,,_5650 <N1DJ Procedure No.:

    GE*UT-245 Instrument:

    BO Tec!JluTomo Manufactunw I Model Version:

    Calibration Sheet No.: APC-009 ORR:

    NIA 11121-09 System Serial No.

    Analog to Digital Converter:

    RD Teclr I EOlX ON Pulser/Receiver.

    RD Tech IEOTX 100 Piggy Board:

    RD T!Ch I EQTX 101 Manulacturer I Model Search Unit:

    B112 Manufacturer Manufacturer I Model OU16 Serial No.

    Cable:

    f2JRG-61 I RG-61 IRG-114 Type;

    ?l1.liX26Jmm Element Size IZJ2fi!l.'lZ§.'l~'

    Length Manufacturer I Model liM&

    WIRL FD 1.fl."

    ~

    o.zr Freq. {MHz)

    Aogle / Mode FSIFD:

    Meesured Incident to AntJe Wedge Front tm No. of lnlennediale Connedorg Calibration standard:

    lfN.1164 Serial No.

    235196 SSl CSllNC.

    Orientation:

    Depth:

    Amplitude I dB:

    Sweep:

    Gain: (dB)

    Screen:

    Field Simulator:

    Reflector:

    Serial No.

    Calibration

    ~

    ~

    ID NO[gj Ill!.

    IDf':!.QlCH 1.30/n.

    1.30/n.

    ~

    • 29.2dB 1.193 In.

    1.193 In.

    '3d8 LOG

    ~

    25 dB Booster:

    15 9F Temp( *F)

    ~

    SSBomoas SIN:

    CAL-RHDM-016 Max Amplitude/dB:

    FARSDH

    -16.ldB o.n6" LOG NIA NIA NIA NIA Sweep:

    Gain: (dB)

    Ti1Tre Initial 1760 Verified Vertfied 1121 Verified Final 1949 Calibration Verification n...-

    02-Nov-IU 07-Nov-IU 01-Nov-IU II Level

    .l.1k

    ._,,:o___

    Level INV-185A 02-Nov-04 Date 1/-9-~'I Date Operator AMR AMR AMR Material Nominal Thickness Measured ~

    Couplant Demit! Waf!lc

    ~

    Type Batch No.

    Acquisition Tmebase:

    dBStart: ~

    Half Path 1

    Range:

    7.016 In.

    Units:

    Avera!jng:

    Digitizing Frequency:

    Acquisition Rate:

    Max Recurrence:

    Wave Mode:

    /.,QDJl.ltudlnal 12,6MHz m.ta.

    1QQQ1ll Scan offset:

    Velocity:

    0.2272 ln.lusec.

    Index offset:

    O,OOOh

    -6.3001D..

    Offset:

    0.000 ln..!usec.

    Angle:

    -~

    Wedge Delay:

    11.00Q usec.

    Skew:

    0.00" Confia uration Channel Name:

    6D°RL 03-676 P3/R3 NOZ§!;.

    Pulser:

    P3 Voltage:

    300V Receiver:

    m Width: (Ns) Z§Q,OOQ/1§.

    Configuration:

    Pf1.ch Catct!

    High Pass:

    !l!1!Jg_

    Receiver Type:

    LQSl Low Pass:

    None Rectification:

    !!JJR9l!lL Smoothing: 1..M!:H N1 D 60° RL AX SCAN NOZ-SE Page

    ~ of

    ~

    ULTRASONIC CALIBRATION DATA SHEET

    ~

    GE Nuclear Energy (Automated with Micro TomoScan)

    IS'ite:

    Ovster Creek Unit: 1 Project: 34705 Report Number:

    005123 Calibration Sheet No.: APC-010

    !Weld:

    NR02 4-5850 fN1DJ Procedure No.:

    GE*UT-245 Version:

    V1 ORR:

    NIA Instrument RD Tech/11.Tomo 11121-0I 1ART 2.2014 Manufacturer I Model System Serial No.

    Acquisition Software Analysls Software Analog to Digital Converter.

    RD Tech I EQTX n§ Pulser/Rec:efver.

    RD T,gr I E!il,TX 100 Piggy Board:

    RD Tech/EQL!Ul1 Manufacturer I Model Manufacturer I Model Manufacturer I Model Search Unit:

    8112 04-.JJ1 W.lix2~tmJ.

    ~

    46°/BL ED 1.,u*

    460 0.76" Manufacturer Serial No.

    Elemenl Size Freq. (Miz)

    Angle/Mode FS/FD:

    Measured Incident lo Cable:

    QJBG-61 I BQ-61 I B!l:.17~

    (1JZ60' !.. l6' !.. 3' Angle Wedge Front Lm Type:

    l.ength No. rl lntennedillte Connedors Calibration standard:

    INV-116.A SSICSUNC.

    1.&<<r 1M!1.:

    . Sel1al No.

    Material Nominal Thiclcness Measured Thiclcness Thermometer:

    ~

    16-F Couplant Demln ~.,.,.

    Serial No.

    Temp("F)

    Type Batch No.

    Calibration A~uisition Orientation:

    ~

    ~

    Tmebase:

    dB Start: 0.000 Range:

    6.016111.

    J'ype:

    IDNO[CH IQ NOTCH Units:

    Half Path Averaijng:

    1 Depth:

    1.80 In.

    1.80 In.

    Digitizing F requeocy:

    §.26MfX Amplitude I dB:

    ~

    -16.Sdlf!.

    Acquisition Rate:

    36§Hz Sweep:

    t.l99 In.

    1.799111.

    Max Recurrence:

    1!!!1!J..&

    Probe Gain: (dB)

    Z!.11§ l:Q!i.

    Wave Mode:

    l,,,.ongltudlnal Scan offset:

    0.000/n.

    Screen:

    ~

    25 dB Booster:

    Active Velocity:

    0.2272 in.lusec.

    Index offset:

    0.000 In.

    Offset:

    0,000 /n./usec..

    Angle:

    46.-<<r Field Simulator: SSB2111R!§ SIN:

    CAL-RHOM4'16 Wedge Delay:

    1Z,OOO usec.

    Skew:

    0.00° Reflector:

    FARSDH NIA Configuration Max Amplitude/dB:

    -12.2d8 NIA Channel Name:

    46°RJ.04-331 P1R1 NOZ-SE Sweep:

    o.nr NIA Pulser:

    f.1.

    Voltage:

    300V Gain: (dB)

    LOG NIA Receiver:

    R1 Width: (Ns)

    ~000[1§.

    Calibration Verification Configuration:

    Pitch Catch High Pass:

    !J9Dg_

    Tl--

    Date Block Operator Receiver Type:

    l.gg Low Pass:

    !J9Dg_

    1 11 1n:,;;

    Initial 2239 02-Nov-04 INV-18SA YS Rectification:

    !fJ1R!1JiJ!

    Smoothing:

    1MHz Verified t'.11 D 45° R!c QIRC SC~N NOZ-SE Verified 1966 07-Nov-04 CAL-RHOM-01f YS Verified Final 0732 08-Nov-04 CAL-RHDM-01!

    YS

    ~Yoshi Sekinuma Ill 02-Nov-04 I~

    I I

    ( )

    ':zfr ll-15~

    Initial Examiner Level Date

    ' ~o~

    ~~I ~! c-,,_

    LL-'l.-of iLL GE Revfe.'

    Level Date ~

    /~

    Page 16 of 19

    ULTRASONIC CALIBRATION DATA SHEET GE Nuclear Energy (Automated with Micro TomoScan) site:

    0-a!,erCreelc Uni: 1 Project: 34705 Report Number:

    005123 Calibration Sheet No.: APC-011 Weld:

    NR02.-.5650 (!J.1Dl Procedure No.:

    GE-UT-245 Version:

    V1 ORR:

    NIA Instrument:

    RD Tech £11.Tomo 1111.1-ot UHi.

    2.2014 Manufacturer I Model System Serial No.

    Acquisition Software Analy&ia Software Analog to Digital Converter:

    RD Tech I EQTX ON Pulser/Receiver:

    BQ Tech I ~QTX 100 Piggy Board:

    RD Tech £C,QTX 101 Manufecturer I Medel Manufactul'8f I Model Manufacturer I Model Search Unit:

    Bm

    .H:1H Q4x17ltmJ.

    L§..IJ1!g 46°/s NIA 46*

    0.66-Manufacturer Serial No.

    Element Size Freq. (MHz)

    AnglefMcde FSIFO:

    Measured Incident to Angla Wedge Front Cable:

    RG:§f. £RG-61 I RG-114 2MJ' 11§.' £ J' 1

    Type:

    length No. d Intermediate Conneclor.I Calibration Standard:

    l!!Y:115A SS/CS/INC.

    1M!L uoo*

    Serial No.

    Material Nominal Thic<<ne&&

    Measured Thickness Thermometer:

    236196 15 '"F Couplant QemlnWatw lf4 Serial No.

    Temp("F)

    Type Balch No.

    Calibration A~uisition Orientation:

    ~

    CIRC Trnebase:

    dB Start: 0.000 Range:

    §..000 !!1.

    lQtJ.OlCH lDNQlCH Units:

    Half Path Averaging:

    1 Depth:

    U!l..ltJ,,

    L.f!l..!&

    Digitizing Frequency:

    1Z.§.MHz Amplitude I dB:

    ~

    -1~.ldB Acquisition Rate:

    366Hz Sweep:

    t.l99 In.

    1.199 la.

    Max Recurrence:

    ~

    Probe Gain: (dB) 7dB

    !..Q§.

    Wave Mode:

    Shear Scan offset:

    -2.600 In.

    Screen:

    !2!JR1!1 25 dB Booster:

    Inactive Velocity:

    O. fZ.40 ln.Jusec.

    Index offset:

    0.000/n.

    • Offset:

    Q.000 ln./usec.

    Angle:

    ~

    Field Simulator: SSRomei!§.

    SIN:

    CAL-RHDM-01§.

    Wedge Delay:

    12.000 usec.

    Skew:

    0.00" Reflector:

    FARSDH NIA Configuration Max Amplitude/dB:

    -20.1 dB NIA Channel Name:

    46°S98-158 P2 NOZ-sE Sweep:

    0.112" NIA Pulser:

    P2 Voltage:

    ~

    Gain: (dB)

    LOG NIA Receiver:

    !JiA Width: (Ns) 33if.~ll!

    Calibration Verification Configuration:

    PutuE~

    High Pass: t:ml1!l

    ~--

    Block f'l.....,,.ftv Receiver Type:

    J.gg Low Pass:

    t:ml1!l I lllR::

    -r--*--*

    Initial 2254 02-Nov-64 INV-186A YS Rectification:

    !1JR!ll!lr.

    Smoothing: l.M!:H Verified N1 D 45° S ~IRC SC8N ~OZ-SE Verified 1963 07-Nov-<U CAL-RHOM-01li YS Verified Final 0733 08-Nov-64 CAL-RHOM-01li YS

    ~

    oshl Sekinuma Ill 02-Nov-04 (

    (

    ,)

    ~

    tl-15*0c./

    ~

    ~.

    u~

    Level Date

    ~

    ~~.#

    Date 1IL

    //"<f~pr

    ~

    ~-_.....,

    GER Level Date

    ?;NII Review Page 1Z of 19

    GE Nuclear Energy ULTRASONIC CALIBRATION DATA SHEET (Automated with Micro TomoScan)

    Site:

    Oyster Creek Unt 1 Project: 34705 Report Number:

    005123 Calibration Sheet No.: APC-012 Weld:

    NR02 4-5650 CN1DJ Procedure No.:

    GE-UT-245 Version:

    ORR:

    NIA Instrument

    • RP Tech I uTomo Manufacturer I Model 11121-0I SY$tem Serial No.

    Acquisition Software Analysis son-re Analog to Oigilal Converter:

    RD T!Ch IE01X091 Pulser/Receiver.

    RD Ted1IEQD(100 Piggy Board:

    RD Tech I EQTX 101 Manufacturer I Model Search Unit:

    Cable:

    Menufactur<< I Model

    ~

    Serial No.

    l2JRG-H I RG-ff IRG-174 Type:

    ?[16x2§J.tmi Element Size tzl.ZM!.' I 26' l 3' Length Manufacturer I Model u.Ml:B.

    WIRL FQ0.11~

    fr o.1r Freq. ~) Angle/Mode FS/FO:

    Measured Incident to Im Angle Wedge Fron!

    No. d Intermediate Connectoni Calibration Standard:

    INV-115A Serie! No.

    23611§ SSlCS/fNC.

    1..§l!r.

    as er:

    Serial No.

    Temp("F)

    Calibration Orientation:

    Type:

    /DNOTCff IDNOTCff Depth:

    L21lJ!1,.

    ~

    Amplitude I dB:

    ~

    -2§.1 dB Sweep:

    1.!fM In.

    t!fUln.

    Gain: (dB)

    "1dB LOG Melerial Couplant Nominal Thicknea Trnebase:

    Units:

    Averaging:

    DemlnWlfer Type Acquisition dB Start: 0.000 Haff Path 1

    Digitizing Frequency:

    Acquisition Rate:

    Max Recurrence:

    NIA Batch No.

    Range:

    3.998 In.

    Wave Mode:

    Longttudm_t Scan offset:

    -6.400 In.

    Screen:

    ~

    25 dB Booster:

    Active Velocity:

    0.2272 /n.lusec.

    Index offset:

    0.000 In, Offset:

    0,000 ln;/Jl!!1£.

    Angle:

    u.ooo.

    Field Simulator: SS Rompas SIN:

    CAL-RHQM-lH6 Wedge Delay:

    11.320 usec.

    Skew:

    0.00° Reflector:

    Max Amplitude/dB:

    Sweep:

    Gain: (dB)

    T.~

    Initial 2219 Verified Verified 1961 Verified Final 0738 FARSDH

    -11.9 dB o.1sr LOG NIA NIA NIA NIA Calibration Verification 02.Nov-04 INV-1B6A OperatlX YS 07-Nov-04 CAL-RH()M.()1li YS OB-Nov-04 CAL-RH()M.()1li YS Configuration Channel Name:

    f.O"RI..98-233 P3/R3 NOi...sE Pulser:

    P3 Voltage:

    Receiver:

    R3 Width: (Ns)

    Configuration:

    Pf1.ch Catch High Pass:

    Receiver Type:

    l.QSl Low Pass:

    Rectification:

    !J.!RgJil[

    Smoothing:

    N1 D 60° RL CIRC SCAN NOZ-SE Ill Level 02-Nov-04 -=-.., ~,I

    ( ~

    ~

    Jf-IS-04 300V 600.QQ2(§

    ~

    tl!HI!!

    1MHz Date r-oe:;;~~~~V §'/ ~el Date j/~ 9 -~~ ~~

    /thAih Date A II Review

    ~

    Page 18 of 19

    .ilC Level

    GE Nuclear Energy

    ~~~~~~~~~~~~~~~~~--~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    NOZZLE to SAFE-END f,~, ;. ns l5itJ 0

    • c-n......, w 5 M*' 5W ;..). PW!'¥'1s~z:;.u;; &**

    P fl

    ~.. p,

    t

    _. >c;:::::

    ':~~~~li*at::_*

    Non-Machined Area

    .s; v11t*f'r1n*

    • P*..,.1,-= rn.,, noo 1-.i. 1 IQll+1tpcr1n,tt1+mm41.g14a11,mnn

    ._ ;,,...,. *-~!?!'*.&-*i:::

    ~-~~-~~--

    1::..1c.f~ *:

    SUMMARY

    NUMBER: QQ.5123 PAGE 12of12

    Report No.:

    HITACHI EXAMINATION

    SUMMARY

    SHEET 1R23-115 Site O~ster Creek Component ID:

    NR02 2-567A WELD Outage 1R23 Nozzle to Shell System:

    212 ASME Cat.:

    B-0 ASME Item 83.90/83.100 Aug Req NIA Exams Performed Data I Cal Sheet I Procedure Calibration Block I

    Exam /Oper.

    Cert Level 1

    Date Sheet I

    Personnel

    _J so* Long.

    D-188 I

    N/A GE-UT-300 Ver/Rev 10 INV-116 Clint Gauthier u

    11/13/2010

    ~-60° Long.

    D-187 N/A GE-UT-300 Ver/Rev 10 CAL-llW2-044 Clint Gauthier II 11/13/2010 60°Shear D-193 N/A GEH-UT-311Ver/Rev16 INV-116 Jimmy Johnson II 11/13/2010 SC° Shear D-192 NIA GEH-UT-311 Ver/Rev 16 INV-116 Jimmy Johnson i

    II 11/13/2010 so* Shear D-191 N/A GEH-UT-311 Voc/R" 18= INV-116 Jimmy Johnson II 11/13/2010 60°Shear D-190 NIA GEH-UT-311Ver/Rev1 INV-116 Jimmy Johnson II 11/13/2010 45°Shear NIA GEH-UT-311 Ver/Rev 16

    ~Jimmy Johnson 11/13/2010 D-189 INV-116 II Examination Results:

    Ultrasonic examination results were acceptable to the requirements of ASME B&PV Code Section XI. 1995 Edition with Addenda through Summer 1996, as modified by the PDI program description and the Federal Register. Part II, Nuclear Regulatory Commission. 10 CFR Part 50 for Category B-D Reactor Pressure Vessel (RPV) Assembly Welds.

    Nozzle to Shell Weld Manual transverse and parallel scans were performed from the OD surface in accordance with procedure GE-UT-300, using 60° Refracted Longitudinal (RU wave search units.

    Nozzle to Shell Weld - Manual parallel scans of the inner 15%T volume were performed from the OD surface in accordance with procedure GEH-UT-311 using model validated search units.

    Nozzle Inner Radius - Manual Zone 1 and Zone 2A scans were performed from the OD surface plate and OD Blend Radius surfaces in accordance with procedure GEH-UT-311 using model validated search units.

    Manual scanning was restricted by the nozzle configuration. proximity of the Nl3B nozzle, and nozzle window access limitations.

    No relevant indications were recorded.

    Achieved Coverage: Nozzle to Shell 28.1%, IRS= 44%.

    Examination results were compared to Data Report N/A from:

    NIA Change These examinations were performed under Work Order:

    C2023090-05 No Change This Summary and the following data sheets have been reviewed and accepted by the following personnel:

    RWP:

    eon:

    519

    zµ;_

    /IO,/o Dose:

    140 mr.

    Prepared By:

    Level:

    Date:

    Utility Review:

    Date:

    a (. L~-

    IJ/JJJ_ta J1_

    ANll Review:

    Date:

    Page 1

    of

    I.

    H~~~;----/

    /-Ultrasonic Calibration and Examination Record --1 I

    1 RPV Components - EPOCH 4 I Site/Unit:

    Oy~;-;;~~e-;k/~--***-- '

    Data Report Number:

    !Bll::fil Linearity Sheet

    .kQ!l!.

    1 Outage:

    1R23 Data Sheet Number:

    D-187 Procedure:

    GE-lff-300 Rev.:

    10 ORR:

    ~

    --- *--*-***--***--** ---*--------~----------------------

    Calibration Block:

    CAL-llW2-044 cs Material Initial Cal:

    0909 Cal Check:

    Cal Check:

    NI A Final Cal:

    270147 Thermometer Flat

    $fl Size Thickness Exam Start: !lli Exam End:

    1532 Sound safe 07220H Couplant Batch 76'F Initial Cal Temp.

    84° F Final Cal Temp:

    DAC Construction Reflector Hole Gain@ !Max Amp I "W" Dim.

    Sweep Screen Depth lX I

    Div.

    SDH

    '0.8'.. ~

    8(11/o g

    0.64" 3.2 i

    lX i

    lX I lX I

    lX I

    DAC lX=

    5&2 dB Sweep 0-10 2.a*

    Depth Note: NIA dB difference between 3/8 and 5/8 Vee Exam Data for Weld:

    NR02 2-561 A WELD OD Plate Exam Surface:

    Nozzle to Shell Configuration:

    92°F Component Temperature Search Unit Data Sigma Manufacturer.

    228C-08001 Serial Number:

    2Cl.1"K. 62"1/ Rect.

    Size I Shape:

    o:r Incident Point:

    Nominal Angle:

    Measured Angle:

    3.0MHz Frequency:

    SDC-3 Model:

    Long.

    Mode:

    Search Unit Cable RG-174 Cable Type:

    9ft.

    Length:

    Q Connectors:

    Instrument Settings Panametrics t. Eeoch 4 031526804 Manufacturer/Model:

    Serial Number:

    9.215us 0.234 in:L.f!.sec.

    0.8-3.0MHz Delay/Zero:

    Velocity:

    Narrowband Filter:

    Auto Full wave 4.0in.

    Sg.{.Med Rep Rate:

    Rectification:

    Range:

    Pulser:

    4000hms 0%

    3.03 MHz Dual Damping:

    Reject:

    Frequency:

    Mode:

    Off:

    Off:

    Off:

    Off:

    DAC:

    TVG:

    CSC:

    DGS:

    Calibration Verification Field Simulator Block S/N:

    !::JM.

    Weld Examination Area:

    Exam Access Scan dB Recordable Exam Reflector

    !:Jf.d Indications Angle Amplitude

    !:Jf.d

    '!~ 1="=rr=o=m=N=1=3~8=to=1=80'~---=T=s=ca=n=------~-=73;.2=_**~~~-N=R=t~-*---*~60"~~**_*=l_Jl-***----~ l --~!:Jf.d===~'-----ll---==---if--"===---

    ~! =1"=~=ro=m=N1===3=8=t=o=180'::=__~_..:.P=s=c=an=._ __ _!:::73=.2=---=N=Rl:.__ _ _..:.60"~___Jlc_ _____ __jl__ _ __:!::!M.==~'----~-===~~**' l---===---

    Acceptable Linearity performed:

    10/27/2010 Comments: Cal/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject= Off.

    Calibration for near surface examination.

    Exams performed a minimum of 14 dB above reference.

    Scanning limited due to N138 on top and access from bioshield window on bottom.

    04 Clint Gauthier

    !l 11/13/2(110 Initials: Examiner Level: Cal/Exam Date:

    Utility Reviewed By:

    !:J.ld

    ~

    • w,51 l~

    C~E-Level:

    11/<.,/,()

    ANll Reviewed By:

    J7J;:_

    GE Reviewed By:

    Level:

    Date:

    Date:

    ujJJJto Date:

    Page L of / 2..

    I--:~**------**

    I

    • HITACHI Ultrasonic Calibration and Examination Record I

    1 RPV Components - EPOCH 4 Site/Unit: Ovster Creek I 1 Dato Report Number:

    1R23-115 Linearity Sheet:

    l-007 Outage:

    1R23 Dato Sheet Number:

    D-188 I

    Procedure:

    GE-lff-300 Rev.:

    10 ORR:

    !:JM

    ~-***---

    i Calibration Block:

    INV-116 Search Unit Data cs 229' 7.87" Sigma 22BC-08001 2a.1"x.62"lf Rect.

    Material Size Thickness Manufacturer:

    Serial Number:

    Size I Shope:

    Initial Col:

    0918 Exam Start:

    1445 Col Check:

    !:JM Exam End:

    1532 0.7" fQ fQ Incident Point Nominal Angle:

    Measured Angle:

    Col Check:

    NIA Soundsafe 07220H Final Col:

    1842 Couplont Botch 3.0MHz SDC-3 long.

    Frequency:

    Model:

    Mode:

    270147 76' F 84° F Thermometer Initial Col Temp.

    Final Col Temp:

    Search Unit Cable DAC Construction RG-174 9ft.

    Q Reflector Hole Goin@ Max Amp! "W' Dim.

    Sweep Screen Cable Type:

    Length:

    Connectors:

    Depth lX i

    Div.

    I Instrument Settings ID Notch 7.87' lX 80%

    15.6' 8.17" fill Panametrics {. Eeoch 4 031526804 lX Manufacturer/Model:

    Serial Number:

    lX 9.215us 0.234 in.[1!,sec.

    0.8-3.0MHz lX i

    Delay/Zero:

    Velocity:

    Narrowband Filter:

    lX fil!t.2 Fullwave 25.0in.

    Sq.[ Med DAC lX=

    71.4dB Rep Rate:

    Rectification:

    Range:

    Pulser:

    4000hms 0%

    3.03 MHz Dual Sweep 0-10 = 12S' Depth Damping:

    Reject:

    Frequency:

    Mode:

    Note: NIA dB difference between 3/8 and 5/8 Vee Off:

    Off:

    Off:

    Off:

    Exam Data for Weld:

    DAC:

    TVG:

    CSC:

    DGS:

    NR02 2-561A WELD Nozzle to Shell Configuration:

    Calibration Verification OD Plate 92° F Field Simulator Block S/N:

    !:JM.

    Exam Surface:

    Component Temperature i I Weld Examination Exam Access Scan dB Recordable Exam Reflector !rn'

    !:JM

    ~

    Area:

    Indications Angle Amplitude i

    !:JM.

    l!

    !:JM

    !:JM.

    l"from NUB to180" Tscan --***--***-****--1 i1

    ~

    !:JM.

    ~

    74.3 NRI fQ Goin (dB) ll_ffe 1[

    I 1H from NHB to 180" Pscan 74.3 NRI oo*

    I L3weep (SD)

    !:JM

    ~

    l Acceptable Linearity performed :

    19f.27{.2010 Comments: Cal/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject= Off.

    Calibration for full volume examination.

    Exams p erformed to maintain a minimum 20% ID roll.

    Non-relevant plate segregates observed.

    Scanning limited due to NHB on top and access from bioshield window on bottom.

    ~

    Clint Gauthier 11

    'Jli..H{.2010 Initials: Examiner Level: Cal/Exam Dote:

    Utility Reviewed By:

    Dote:

    !:JM.

    !:JM

    _F'h_,_f~rJ.e-~"""-'-=-=-* -*~~~"hfftD

    ~s: Examiner Level:

    "lo ff(

    ~

    GE Reviewed By:

    Level:

    Date:

    ANll Reviewed By:

    Dote:

    Page '3 of / l...

    HITACHI Ultrasonic Calibration and Examination Record Site/Unit: Ovster Creek I 1 Outage:

    1R23 Procedure.

    GEH-UT-311 Calibration Data for Block:

    INV-116 cs Material 22!1' Size 7.87' Thickness Initial Col:

    0913 Col Check:

    !:JM Exam Start:

    1310 Exam End:

    1424 Cal Check:

    !:JM Final Cal:

    1857 270147 Thermometer Soundsafe Couplant:

    ~

    Initial Cal Temp.

    DAC @ lX= 39.0 dB Sweep 0-10 = 15.<1' Metal Path 07220H Botch

    ~

    Final Col Temp:

    Acceptable Linearity performed:

    10/27/201.0 Exam Data for Component:

    NR02 2-567A WELD Nozzle to Shell OD Plate Exam Surface:

    Exam Configuration:

    Rotation Inner Radius Examinations - EPOCH 4 Data Report Number: ~ Linearity Sheet:

    L-005 Data Sheet Number:

    IH89 Rev:

    16 ORR:

    10-22 Search Unit Data KBA Manufacturer:

    01FRNP Serial No.:

    0.5" x 1.C1' I Rect.

    Size/Shope:

    0.7 in.

    45° 45° Incident Point:

    Nominal Angle:

    Measured Angle:

    ~

    Frequency:

    113-891-600 Model:

    Search Unit Cable 12ff.

    Shear Mode:

    Q RG-174 Coble Type:

    Length:

    Connectors:

    Instrument Settings Panametrics I Epoch 4 Manufacturer/Model:

    031572911 Serial No.:

    13.22us 0.1281 in 11:1.sec 0.8-3.0MHz Zero:

    Velocity:

    Narrowband Filter:

    Auto Fullwave 15.00in.

    Sg./ Med Rep Rote:

    Rectification:

    Range:

    Pulser/Energy 4000hms OOA>

    1.0MHz P1f Dom ping:

    Reject:

    Frequency:

    Mode:

    Off:

    Off:

    Off:

    Off:

    DAC:

    TVG:

    CSC:

    DGS:

    Calibration Verification Field Simulator Block S/N:

    !:JM Reflector

    !:JM

    !:JM

    !:JM Amplitude

    !:JM

    !:JM NIA Goin{dB)

    !:JM

    !:JM

    !:JM Sweep{SD)

    !:1M

    !:JM

    !:JM Comments: Cal/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject= Off.

    Calibration for nozzle to vessel weld IN/VJ.

    Exams performed to maintain a 20-30% FSH clad roll.

    Scanned CW and CCW.

    Examined 1" from N138to1800 due to limited access.

    -W-Jimm~ Johnson 11 1'!:1..13{.2aJ.O Initials: Examiner:

    Level:

    Col/Exam Dote:

    ~

    lit.

    ~

    GE Reviewed By:

    Level:

    Dote:

    Utility Reviewed By:

    Dote:

    .1f _s. l~

    ~/-'

    ANll Reviewed By:

    Dote:

    Page Y of {L I

    Ultrasonic Calibration and Examination Record Inner Radius Examinations - EPOCH 4 n

    ~-

    ~

    Site/Unit Qi!ster Creek I 1 Doto Report Number:

    1R23-115 Linearity Sheet:

    l-005

    • Outage:

    1R23 Data Sheet Number:

    D-190 Procedure:

    GEH-UT-311 Rev:

    16 DRR:

    10-22 Calibration Data for Block:

    INV-ll6 Search Unit Data cs 229' 7.87" KBA 01X820 0.5" x 1.cr I Rect.

    Material Size Thickness Manufacturer:

    Serial No.:

    Size/Shape:

    Initial Cal:

    0909 Exam Start:

    1310 0.7 in.

    Ell' Ell' Cal Check:

    !:Ji!J.

    Exam End:

    1424 Incident Point:

    Nominal Angle:

    Measured Angle:

    Cal Check:

    NIA Soundsafe 07220H 1.0MHz 113-891-600 Shear Final Cal:

    1859 Couplant:

    Batch Frequency:

    Model:

    Mode:

    2701.47 76" F 84°F Search Unit Cable Thermometer Initial Col Temp.

    Final Col Temp:

    RG-174 12ft.

    Q DAC Construction Coble Type:

    Length:

    Connectors:

    ~

    Reflector Depth Goin@ jMox Ampj "W" Dim.

    Sweep Screen I

    Instrument Settings lX i

    Div.

    ID Notch 7.87' lX 80%

    14.9' 16.S" Zd I

    Panametrics I Epoch 4 031572911 I

    I Manufacturer/Model:

    Serial No.:

    I lX I

    15.23us 0.1282 in f.l:!.sec 0.8-3.0MHz DAC@lX= 54.SdB Zero:

    Velocity:

    Narrowband Filter:

    Auto Fullwave 22.50in.

    Sq.I Med Sweep 0-10 = 22.!!l' Metal Path Rep Rate:

    Rectification:

    Range:

    Pulser/Energy Acceptable Linearity performed :

    l'Jf..27{_2010 4000hms 0%

    1.0MHz Ea.

    I Damping:

    Reject:

    Frequency:

    Mode:

    I Exam Data for Component:

    NR022-56lA WELD Off:

    Off:

    Off:

    Off:

    Nozzle Inner Radius DAC:

    TVG:

    CSC:

    DGS:

    Configuration:

    OD Plate 92° F Calibration Verification Exam Surface:

    Component Temp.

    Examination Exam Rotation Wedge Scan Recordable Field Simulator Block S/N:

    !:Ji!J.

    Area Angle Angle S/N dB Indications Reflector

    !:Ji!J.

    !:Ji!J.

    0- 7.fJ' 60

    t25.0"

    !:Ji!J.

    80.5 NRI Amplitude

    !:Ji!J.

    !:Ji!J.

    Goin (dB)

    !:Ji!J.

    !:Ji!J.

      • -~*--

    Sweep(SDJ NIA

    !:Ji!J.

    Comments: Col/Exam Dote is the dote of initial calibration. See coverage sheet for limitations. 0% Reject= Off.

    Calibration for Zone 1.

    Exams performed to maintain a 20-30% FSH clad roll.

    Scanned CW and CCW.

    Examined 1" from N138to180" due to limited access.

    -P9-Jimmy Johnson Initials: Examiner:

    11 11/13/2010 Level:

    Cal/Exam Dote:

    (JM£.-~~*

    GE Reviewed By:

    Level:

    ~

    Date:

    Utility Reviewed By:

    Date:

    I !l!!Jj_;o ANll Reviewed By:

    Date:

    !:Ji!J.

    !:Ji!J.

    !:Ji!J.

    !:Ji!J.

    Page S of I Z..

    re ~IT~HI

    ~--***--

    Ultrasonic Calibration and Examination Record l Inner Radius Examinations - EPOCH 4 Site/Unit: Ovster Creek/ 1 Data Report Number:

    1R23-115 Linearity Sheet:

    L-005 I

    Outage:

    1R23 Data Sheet Number:

    D-191 Procedure:

    GEH-UT-311 Rev:

    16 DRR:

    10-22 I

    Calibration Data for Block:

    INV-116 Search Unit Data cs 22g*

    7.87" KBA 01FRPB 0.5" x 1.U'/..Rect.

    Material Size Thickness Manufacturer:

    Serial No.:

    Size/Shape:

    ~nitial Cal:

    0911 Exam Start 1310 0.7 in.

    fQ fQ Cal Check:

    !:11.B_

    Exam End:

    1424 Incident Point Nominal Angle:

    Measured Angle:

    Cal Check:

    NIA Soundsafe 07220H l.OMHz 113-891-600 Shear rinal Cal:

    1902 Couplant:

    Batch Frequency:

    Model:

    Mode:

    270147 76" F 84°F Search Unit Cable Thermometer Initial Cal Temp.

    Final Cal Temp:

    RG-174 12ft.

    Q DAC Construction Cable Type:

    Length:

    Connectors:

    lReflectofl

    ~---~~------~

    Depth Gain@ JMax Amp! "W" Dim.

    Sweep I Ser~~

    Instrument Settings lX I

    Div.

    I ID Notch 7.87" lX 800A>

    14.!1' 16.5

    4.7 Panametrlcs I Epoch 4 031572911 I

    I I

    Manufacturer/Model:

    Serial No.:

    lX 15.23 us 0.1282 In L11.sec 0.8-3.0MHz DAC@lX=

    54.SdB Zero:

    Velocity:

    Narrowband Filter:

    Sweep0-10= 35.<J' Auto Full wave 35.00in.

    Sq.I Med Metal Path Rep Rate:

    Rectification:

    Range:

    Pulser/Energy Acceptable Linearity performed:

    10/27/.2010 4000hms 0%

    1.0MHz

    !!ff.

    Damping:

    Reject:

    Frequency:

    Mode:

    Exam Doto for Component:

    NR02 2-SfilA WELD Off:

    Off:

    Off:

    Off:

    Nozzle Inner Radius DAC:

    TVG:

    CSC:

    DGS:

    Configuration:

    OD Plate 92° F Calibration Verification Exam Surface:

    Component Temp.

    Examination Exam Rotation Wedge Scan Recordable Field Simulator Block S/N:

    !:11.B_

    Area Angle Angle S/N dB Indications Reflector

    !:11.B_

    NIA i=WA

    ! Q.:...1Q,J!

    Z9.

    t.200

    !:11.B_

    90.5 NRI Amplitude NIA

    !:11.B_

    !:11.B_

    I Gain (dB)

    !:11.B_

    !:11.B_

    - !:11.B_

    I

    ~

    !:11.B_

    ~ J

    !:11.B_

    Comments: Cal/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject= Off.

    Calibration for Zone 2A.

    Exams performed to maintain a 20-300A> FSH clad roll.

    Scanned CW and CCW.

    Calibration on fU flat wedge. Scanned on 700 flat wedge per ORR 10-20 due to insufficient block length.

    Examined l" from Nl38 to 1800.

    C'11Y1 r#iL Jimm't. Johnson 11 11/lJf.2010 Initials: Examiner:

    Level:

    Cal/Exam Date:

    Utility Reviewed By:

    Date:

    C!Q/YC

    ~ id~{)

    • 11. S_. /~

    I !/_!Jj_ I tJ GE Reviewed By:

    Level:

    Date:

    ANll Reviewed By:

    Date:

    Page h of 12-

    HITACHI Ultrasonic Calibration and Examination Record Inner Radius Examinations - EPOCH 4 Site/Unit: Oyster Creek I 1 Outage:

    1R23 Procedure:

    GEH-UT-311 Calibration Data for Block:

    JNV-116 cs Material 22g*

    Size 7.87" Thickness Initial Cal:

    0913 Cal Check:

    !:JfA Exam Start:

    1310 Exam End:

    1424 Ca/Check:

    NIA Final Cal:

    1903 Soundsafe Couplant:

    07220H Batch 270147 Thermometer 76°F Initial Cal Temp.

    84°f Final Cal Temp:

    DAC@ lX=

    54.5 dB Sweep 0-10 = 22.!l' Metal Path Acceptable Linearity performed:

    10{27/2010 Exam Data for Component:

    NR02 2-567A WELD Nozzle Inner Radius Configuration:

    ODBR Exam Surface:

    92° F Component Temp.

    Data Report Number:

    1R23-115 Linearity Sheet:

    L-005 Data Sheet Number:

    D-192 Rev:

    16 DRR:

    10-22 KBA Manufacturer:

    Search Unit Data 01FRP4 Serial No.:

    0.5 K 1.a'/Rect Size/Shape:

    Incident Point:

    Nominal Angle:

    Measured Angle:

    1.0MHz Frequency:

    113-891-600 Model:

    Search Unit Cable 12ft.

    Shear Mode:

    Q RG-174 Cable Type:

    Length:

    Connectors:

    Instrument Settings Panametrics I Epoch 4 Manufacturer/Model:

    031572911 Serial No.:

    15.23 us 0.1282 in t.11.sec 0.8-3.0MHz Zero:

    Velocity:

    Narrowband Filter:

    Auto Ful/wave 22.50in.

    Sg./Med Rep Rate:

    Rectification:

    Range:

    Pu Iser/Energy 4000hms 0%

    l.OMHz fil Damping:

    Reject:

    Frequency:

    Mode:

    Off:

    Off:

    Off:

    Off:

    DAC:

    IVG:

    CSC:

    DGS:

    Calibration Verification Examination Exam Rotation Wedge Scan Recordable Field Simulator Block S/N:

    Area Angle Angle S/N dB Indications Reflector Amplitude

    • I Gain (dB) r--------------------------; ~e:~sJU.

    Comments: Cal/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject= Off.

    • Calibration for Zone 2A.

    EKams performed to maintain a 20-30% FSH clad roll.

    Scanned CW.

    Calibration Sweep is 22.!l' metal path, Examination Range setting is 15.a'.

    Examined l" from Nl38to180" due to limited access.

    __Jj_ Jimm'l_Johnson 11 l!f.13/2010 Initials: Examiner:

    Level:

    Cal/Exam Date:

    Utility Reviewed By:

    CQ/1£ JJL_

    llh1.,Jo

    /fl, ;,,~*-

    GE Reviewed By:

    Level:

    Date:

    ANll Reviewed By:

    Date:

    I !./!_!1)_ I O Date:

    Page 7 of /Z..

    HITACHI Ultrasonic Calibration and Examination Record Inner Radius Examinations - EPOCH 4 Site/Unit: Oyster Creek/ 1 Outage:

    1R23 Data Report Number:

    1R23-115 Linearity Sheet:

    L-005 Data Sheet Number:

    D-193 Procedure:

    GEH-UT-311 Rev:

    16 ORR:

    10-22 Calibration Dato for Block:

    INV-116 cs Material Initial Cal:

    0916 CalCheck:

    ~

    Cal Check:

    NIA Final Cal:

    1905 ll!!12l.

    Thermometer 229' Size 7.87' Thickness Exam Start 1310 Exam End:

    1424 Soundsafe Couplant:

    76° F Initial Cal Temp.

    07220H Batch 84° F Final Cal Temp:

    DAC @ lX=

    54.5 dB Sweep 0-10 = 2ZS' Metal Path Acceptable Linearity performed:

    10/27/2010 Exam Data for Component:

    NR02 2-567A WELD Nozzle Inner Radius Configuration:

    ODBR Exam Surface:

    92°F Component Temp.

    Examination Area Exam Angle Rotation Angle Wedge SIN Scan Recordable dB Indications 88.5 NRI KBA Manufacturer:

    Search Unit Data 01FRP8 Serial No.:

    0.5" x 1.CJ'/Rect.

    Size/Shape:

    Incident Point:

    Nominal Angle:

    Measured Angle:

    1.0MHz Frequency:

    113-891-600 Model:

    Search Unit Cable 12ft.

    Shear Mode:

    Q RG-174 Cable Type:

    Length:

    Connectors:

    Instrument Settings Panametrics I Epoch 4 Manufacturer/Model:

    031572911 Serial No.:

    15.23 us 0.1282 in LM.sec 0.8 3.0MHz Zero:

    Velocity:

    Narrowband Filter:

    Auto Fullwave 22.50in.

    Sq.I Med Rep Rate:

    Rectification:

    Range:

    Pulser/Energy 4000hms 0%

    1.0MHz

    !?ff.

    Damping:

    Reject:

    Frequency:

    Mode:

    Off:

    Off:

    Off:

    Off:

    DAC:

    TVG:

    CSC:

    DGS:

    Calibration Verification Field Simulator Block S/N:

    NIA Reflector

    ~

    ~

    NIA Amplitude

    !JM

    !JM

    ~

    ~

    !JM.

    !JM

    ~

    ~-----*----

    Comments: Cal/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject = Off.

    Calibration for Zone 2A.

    Exams performed to maintain a 20-30"Ai FSH clad roll.

    Scanned CCW.

    Calibration Sweep is 22.s' metal path, Examination Range setting is 15.CJ'.

    Examined CW/CCW 1" from N13B to 180" due to limited access.

    __Jj__ JimmY._ Johnson ll 1U,13/2010 Initials: Examiner:

    Level:

    Cal/Exam Date:

    Utility Reviewed By:

    WA TfZ l/bt.lc 1f _f I l~

    GE Reviewed By:

    Level:

    Date:

    ANll Reviewed By:

    Date:

    11/;q/10 Date:

    Page 8 ot 12.

    "l1 l.O

    (\\)

    ~

    Q.,

    I~

    HITACHI Reactor Pressure Vessel Coverage Calculation Sheet Oyster Creek NGA - Core Spray CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length =

    360 Area sq. in.

    Area Scanned of Area Weld Length Percent Exam Volume =

    66.3 IRS-Scan LKCW (S4)

    A 7.4 7.4 11.2%

    158 1.2%

    IRS-Scan LKCCW ($4)

    A 7.4 7.4 11.2%

    158 1.2%

    60° P-Scan (S6l A

    58.9 30.5 46.0%

    158 10.1%

    60° T-Scan (S41 A

    7.4 7.4 11.2%

    158 2.4%

    60° T-Scan !S6l A

    58.9 39.5 59.6%

    158 13.1%

    % Total Composite Coverage=

    28.1%

    Rev. 0 9/23/0' Comments A - Scanned area from 1 inch CW of nozzle Nl3B CW to 180°. Scanning limited due to nozzle configuration, proximity of the Nl3B and the N6A nozzle window configuration. Examined from the N4A nozzle window Note - Rounding methods may affect calculated values. S4-Supplement 4 underclad volume, S6-Supplement 6 volume. Weld length in degree~

    ~

    ()

    (D

    <D A"

    N 0

    0

    -0 Cl I.Cl ro 10:

    0 -

    1~

    /

    //

    let I

    60°T/P I

    I I

    I I

    I I

    I 11 ----1 Radial Plate T Norn.= 7.125" Ciad T Norn.= 0.2i875" 11.5" 60°P 19.6" 60°T I

    Oyster Creek Core Spray 60° S4 Exam Volume= 7.4 Sq. In.

    60° S6 Exam Volume = 58.9 Sq. In.

    60° S4 IRS-Scan LKCW achieved= 7.4 Sq. In.

    60° S4 IRS-Scan LKCCW achieved= 7.4 Sq. In.

    60° S6 P-Scan achieved = 30.5 Sq. In.

    60° S4 T-Scan achieved= 7.4 Sq. In.

    60° S6 T-Scan achieved= 39.5 Sq. In.

    ~

    ~o z

    CD 1'11 0

    r-1 z

    f / (_

    Page 0 ~

    ManDet Nir_PDI Oyc_Rev 6.XLS MANUAL DETECTION NOZZLE INNER RADIUS ANO BORE INSPECTION REQUIREMENTS PLANT OYSTER CREEK PREPARED SY S.C MORTENSON NOZZLE SCAN SCAN BEAM EXAM ZONE SURFACE AREA ANGLE RECIRC INLET ZONE l{M)

    PLATE 5.0" -10.0" ss.o*

    ZONE l!M)

    PLATE 0-14.0" 6s.o*

    ZONE2A!M)

    PLATE 0 8.0" 10.0*

    ZONE2A{MI PLATE 0-8.0" so.o*

    FEEDWATER NNWeld(MI PLATE 0 6.5" 5s.o*

    Zone l !Ml PLATE 0-6.0" 60.o*

    Zone2A{M)

    PLATE 0-7.0" 70.0° Zone2AIMI ODBR 40* 90° 67.3° Zone 2BIMI BARREL ALL 39.0° Zone3(M)

    BARREL ALL 28.0 CORE SPRAY N/VWeld(MI PLATE 0- 6.5" 4s.o*

    Zone 1 (Ml PLATE 0- 7.0" 60.0° Zone2A!MI PLATE 0-10.0" 7o.o*

    Zone2AIMJ ODBR so* - go*

    66.1° Questions on this NIR requirements sheet shall be directed to 5.C. Mortenson@ 704 577-3770 Digitally signed by Chris Minor Chris M

    • ON: cn=Chris Minor, o=GE Hitachi, I n 0 r ou=Nudear Energy, emall=Chris.Minor@ge.com, c=US Date: 2010.10.26 12:39:46 -04'00' SME Review f Date DATE 10/25/10 ROTATION WEDGE Metal OFFSET ANGLE RADIUS Poth

    +/-45° FLAT 16.9"

    +/-40° FLAT 27.0"

    +/-35° FLAT 17.2"

    +/-35° FLAT 16.0"

    +/- 35.0° - 55.0' FLAT 13.4"

    1:40.0*

    FLAT 16.0"

    +/- 2s.o*

    FLAT 26.0" 25.4° 2.3" 9.6" 46.s*

    FLAT 7.4" 9o.o*

    FLAT 6.1"

    +/- 3s.o* - 65.0' FLAT 10.5"

    +/- 2s.o*

    FLAT 16.1" 20.0° FLAT 23.0" 19.3° 1.6" 7.7' NOTES:

    IMI MANUAL xx.x* (xx.><")

    WEDGE/ IFIXTUREJ ROTATION ANGLE Pqge __il of I Z..

    FREQ 1.0 MHz 1.0 MHZ lOMHz 1.0 MHz 1.0 MHz 1.0 MH:z 1.0 MHz 1.0 MHz W-240 2.0 MHz 2.0 MHz 1.0 MHZ 1.0 MHZ 1.0 MHZ 1.0 MHz W-078 Site Review f Date Examination Summary Sheets for Welds NE 5-0002, NE 5-0022A, and NG-D-0002

    c" Report No.:

    EXAMINATION

    SUMMARY

    SHEET OCR20-143 GE NUCLEAR ENERGY O]tster Creek Component ID:

    NE-5-0002 Site:

    I Outage:

    1R20 Safe End to Elbow (NSB)

    I System lso. Cond.

    ASMECat.:

    B-J ASME/tem 89.11 Aug Requirement:

    Exams Perfonned Data Sheet Cal Sheet Procedure Calibration Block Examination Cert Level Date Personnel 45° Shear UT-190 N/A GE-PDl-UT-2 ASMEALT.

    Paul Vaiden II 11/13/2004 BLOCK 3908 so* RL UT-191 N/A GE-PDl-UT-2 ASMEALT.

    Paul Vaiden II 11/13/2004 BLOCK3908 Examination Results:

    During the manual ultrasonic examination of the above referenced component, no recordable indications were detected utilizing the 45*

    shear and 60°RL wave search units..

    The exam was perfo.nned from the (Downstream) Elbow side only due to the Safe-End to Elbow configuration.

    50% of the Code required volume was examined.

    c This examination meets the requirements of the 1995 Edition of ASME Section XI, 1996 Addenda.

    Summary No. 005294.

    Examination results were compared to data report

    i/!r from /Jiii outage with 0

    No Change These examinations were performed under Work Order:

    C2007458 0

    Change This Summary and the following data sheets have been reviewed and accepted by the following personnel:

    (jj)~ ~- uMi c

    Prepared fu; Level:

    Date:

    Utility Review:

    Date:

    --~~ 11i1d1 ANllR~ --"/

    Date:

    Page 1

    of 4

    Ultrasonic Calibration and Examination Record GE NUCLEAR ENERGY Manual Piping and Components Report Number:

    005294 Site/Unit: Or,ster Creek I 1 Data Sheet Number:

    UT-190 Outage: 1R20 Linearity Sheet:

    L-006 Calibration Data for Block ASME ALT. BLOCK 3908 Procedure:

    GE-PDl-UT-2 I

    SIS Flat 1.0" Ver I Rev: R3 ORR: NIA I

    Calibration Cal Time Material Size Thick Initial Cal:

    1055 Search Unit Data Soundafe 19620 Cal Check: 1146 KBA OOC6H9 0.375"1Round Couplant:

    Couplant batch 235141 70"F Cal Check:

    NIA Manufacturer:

    Serial Number Size/Shape:

    Thermometer SIN Cal Temp.

    Final Cal:

    1245 0.25in.

    45" 45" Incident Point:

    Nominal Angle:

    Measured Angle:

    DAC Construction 1.5MHz ComQ:G Shear 1

    Scan Direction Ax NIA NIA Frequency:

    Style:

    Mode:

    Elements:

    Cal Reflector 1.0" Notch NIA NIA Search Unit Cable Signal Amplitude 80%

    ~

    ~

    RG-174

    §:

    Q Signal Sweep:

    7.0Dlv

    .ODiv

    .OD/v Cable Type:

    Length:

    Connectors:

    Signal dB:

    7.1dB

    .OdB

    .OdB Sweep 0-10 = 2.034/n Meta/Path Instrument Settings Calibration Verification Panametrics I EQoch 4 031574612 Maufacturer/Model:

    Serial Number:

    Field Simulator Block SIN:

    CAL-RHOM-010 Reflector FSH NIA 5.985us 0.1230 lnJusec.

    0.8-3.0MHz Amplitude 20"Ai NIA Zero:

    Velocity:

    Narrowband Filter:

    Gain (dB) 7.1 NIA Auto Fullwave 2.034/n Sq.I Max Sweep (SD) 5.0 NIA I

    Rep Rate:

    Rectification:

    Range:

    Pulser/Energy:

    Acceptable Linearity performed : 10/2512004 4000hms Off 2.0MHz PIE Damping:

    Reject:

    Frequency:

    Mode:

    Exam Data for Weld: NE-5-0002 I

    Safe End to Elbow (N5B!

    Exam Comments I Limitations:

    I Configuration:

    Examinatioo was perf'nnn&d from ti1'1} DNST Elbow side c:ily I

    OD 84"F 235141 due to Safe End to Elbow configutatiCll.

    I Exam Surface:

    Exam Temp.

    Exam Thermometer Maintained a 5% - 20% ID Roll throughout exam.

    No recordable indications.

    I Axial UPST Scan dB Recordable Exam I

    Circ DNST Indications Angle Axial DNST 20 NRI 45*

    Clrc DNST 20 NRI 45*

    I I

    I Exam Start:

    1147 Exam End:

    1200 I

    ~

    Paul Vaiden ll h/IJ{}

    ~

    11hsiE*1 I

    ~

    Re'viewed By:

    I Initials:

    Examiner:

    Level:

    Level:

    Date:

    1 Utility Review:

    I Date:

    I Initials:

    Examiner2:

    Level:

    ~'-/./!

    ~v I

    ./

    I Initial Cal/Exam Date:

    11113/..2004 A~ll Rejfe_;:vf Page 1 of!

    Date:

    Ultrasonic Calibration and Examination Record GE NUCLEAR ENERGY Manual Piping and Components Report Number.

    005294 Site/Unit:

    O~ster Creek I 1 Data Sheet Number:

    UT-191 Outage: 1R20 Linearity Sheet:

    L-006 Calibration Data for Block ASME ALT. BLOCK 3908 Procedure:

    GE-PDl-UT-2 Ver I Rev: R3 ORR: NIA 1.0" SIS Flat Calibration Cal Time Material Size Thick Initial Cal:

    1100 Search Unit Data Soundsafe 19620 Cal Check:

    1200 RTD 99-506 2(8x141 mmlRect Couplant:

    Couplant batch 235141 70"F Cal Check:

    NIA Manufacturer:

    Serial Number Size/Shape:

    Thermometer SIN Cal Temp.

    Final Cal:

    1246 0.3/n.

    60° 60° Incident Point:

    Nominal Angle:

    Measured Angle:

    DAC Construction 2.0MHz TRLA RL i

    Scan Direction Ax NIA NIA Frequency:

    Style:

    Mode:

    Elements:

    Cal Reflector 1.0" Notch NIA NIA Search Unit Cable Signal Amplitude 80%

    ~

    RG-174

    ~

    Q Signal Sweep:

    7.0Div

    .ODiv

    .ODiv Cable Type:

    Length:

    Connectors:

    I Signal dB:

    43.5dB

    .OdB

    .OdB Sweep 0-10=

    2.849in Metal Path Instrument Settings Calibration Verification Panametrics I Er1.och 4 031574612 Maufacturer/Model:

    Serial Number:

    I Field Simulator Block SIN:

    CAL-RHOM-010 8.774us 0.2320 inJusec.

    0.8-3.0MHz Reflector FSH NIA Amplitude 80%

    NIA Zero:

    Velocity:

    Narrowband Filter:

    Gain (dB) 36.8 NIA Auto Fullwave 2.849/n Sq.I Max Sweep (SD) 5.4 NIA Rep Rate:

    Rectification:

    Range:

    Pulser/Energy:

    Acceptable Linearity performed : 10/2512004 4000hms Off 2.0MHz Dual Damping:

    Reject:

    Frequency:

    Mode:

    Exam Data for Weld: NE-5-0002 I

    Safe End to Elbow (N5Bl Exam Comments I Limitations:

    I Confi uration:

    g I

    ExammatiiJn ~as JVJrformed from the DNST Elbow sidP only d

    to S fe E d to Elbo nfii ti ue a

    n wco gura on.

    OD 84"F 235141 Exam Surface:

    Exam Temp.

    Exam Thermometer Scanned at reference in order to maintain a 5% to 20% ID roll.

    No Recordable Indications.

    I Axial UPST Scan dB I Recordable Exam I

    Circ DNST Indications Angle Axial I

    DNST 43.5 NRI I 60° I

    I Exam Start:

    1201 Exam End:

    1207 I

    y lff~

    ~~t 1

    I Paul Vaiden

    !1 I

    i I

    Initials:

    Examiner:

    Level:

    GE Reviewed By:

    Level:

    Date:

    I I

    I I ---

    I

    ~

    Date:

    I Initials:

    Examiner2:

    Level:

    t/iJ/tY I

    I I

    Initial Cal/Exam Date:

    1111312004 Page ~ of!

    I ANll view:

    Date:

    I I

    \\...J

    --t 1-

    --v---

    ~ -

    Wall Thickness Site:

    Oyster Creek Unit:

    1 Report No.:

    GE NUCLEAR ENERGY Profile Sheet Project:

    1R20 005294

    ~

    System:

    /so. Cond.

    ~ ~

    Component ID Number:

    NE-5-0002 Position o*

    90° 180° 270°

    ((]

    [!]

    121 r4l

    @]

    1 NIA NIA NIA NIA Crown Height:

    Flush I

    2 0.88 NIA NIA NIA I

    Crown Width:

    1.3" I

    0.92 NIA NIA NIA Safe End Elbow 3

    I UPST Component:

    DNST Component:

    Nominal Diameter 10/n.

    I 4

    0.8 NIA NIA NIA I

    I Weld Length:

    33.50 In.

    FLOW.,.

    5 0.64 NIA NIA NIA T&C's taken from previous data report no. OCR19-047 dated 10/12/02.

    4..

    l?v.

    Paul Vaiden

    !1 1111312004 na-mr-

    ~ ~

    ANll~~ /;zi#y

    ~

    Initials: Examiner:

    Level:

    Date:

    GE Reviewed By:

    Level:

    Date:

    Utility Review:

    Date:

    Date:

    Page of !

    ~*--S-ite_:_G_E_N_:-:-:-:-:-:-:-~-:-R_G_Y Report No.:

    OCR20-142 EXAMINATION

    SUMMARY

    SHEET Component ID:

    NE-5-0022A Outage:

    1R20 Safe End to Elbow (NSA)

    System lso. Cond.

    ASMECat.:

    B-J ASME Item 89.11 Aug Requirement:

    Exams Performed Data Sheet Cal Sheet Procedure Calibration Block Examination Cert Level Date Personnel 45" Shear UT-182 NIA GE-PDl-UT-2 ASME-ALT.

    Paul Vaiden II 11113/2004 BLOCK3908 60" RL UT-188 NIA GE-PDl-UT-2 ASMEALT.

    Paul Vaiden II 11/13/2004 BLOCK3908 Examination Results:

    During the manual ultrasonic examination of the above referenced component, no recordable indications were detected utilizing the 45" shear and 60"RL wave search units..

    The exam was performed from the (Downstream) Elbow side only due to the Safe-End to Elbow configuration.

    50% of the Code required volume was examined.

    C This examination meets the requirements of the 1995 Edition of ASME Section XI, 1996 Addenda.

    c Summary No. 005296.

    Examination results were compared to data report These examinations were performed under Worlc Order.

    N/A from N/A outage with C2007457 This Summary and the following data sheets have been reviewed and accepted by the following personnel:

    s ;p.....-.. ;e
    ;p<L!!!! ~

    ..... ~

    ..... ~

    u..e10 D*teo /~

    A~

    ~~~~~~~-

    Date:

    11,/i1,M Date:

    D D

    No Change Change Page 1

    of 4

    Ultrasonic Calibration and Examination Record GE NUCLEAR ENERGY Manual Piping and Components Report Number:

    005296 Site/Unit: O~ster Creek I 1 Data Sheet Number:

    UT-182 Outage: 1R20 Linearity Sheet:

    L-006 Calibration Data for Block ASME-ALT. BLOCK 3908 Procedure:

    GE-PDl-UT-2 SIS FLAT 1.0*

    Calibration Ver I Rev: R3 ORR: NIA Cal Time Material Size Thick Initial Cal:

    1055 Search Unit Data Soundsafe 19620 Cal Check: 1217 KBA OOC6H9 0.375*/Round Couplant:

    Couplant batch 235141 70°F Cal Check: NIA Manufacturer:

    Serial Number Size/Shape:

    Thermometer SIN Cal Temp.

    Final Cal:

    1245 0.25/n.

    45° 45*

    Incident Point:

    Nominal Angle:

    Measured Angle:

    DAC Construction 1.5MHz Como-G Shear 1

    Scan Direction Ax NIA NIA Frequency:

    Style:

    Mode:

    Elements:

    Cal Reflector 1.0Notch NIA NIA Search Unit Cable Signal Amplitude 80%

    ~

    ~

    RG-174 Q

    Signal Sweep:

    7.0D/v

    .ODiv

    .ODiv Cable Type:

    Length:

    Connectors:

    Signal dB:

    7.1dB

    .OdB

    .OdB Sweep 0-10 =

    2.034in Meta/Path Instrument Settings Calibration Verification Panametrics I §1.och ~

    031574612 Maufacturer/Model:

    Serial Number:

    Field Simulator Block S/N:

    CAL-RHOM-010 Reflector FSDH NIA I

    5.985us 0.1230 lnJusec.

    0.8-3.0MHz Amplitude 20%

    NIA Zero:

    Velocity:

    Narrowband Filter:

    Gain (dB) 7.1 NIA Auto Fullwave 2.034/n Sq.I Max I Sweep (SD) 5.0 NIA Rep Rate:

    Rectification:

    Range:

    Pulser/Energy:

    Acceptable Linearity performed : 10/2512004 4000hms Off 2.0MHz PIE Damping:

    Reject:

    Frequency:

    Mode:

    Exam Data for Weld: NE-5-0022A Safe End to Elbow (N5Al Exam Comments I Limitations:

    Configuration*

    Examination was per~

    from the DHST E~bow side Mly I

    due to Safe Enel to Elbow configuration OD 84°F 235141 Maintained a 5% - 20% ID Roll throughout exam.

    Exam Surface:

    Exam Temp.

    Exam Thermometer I No recordable indications.

    Axial UPST Scan dB Recordable Exam I

    Circ DNST Indications Angle i

    AXIAL DNST 20.0 NRI 45*

    CIRC DNST 20.0 NRI 45° Exam Start:

    1218 Exam End:

    1230 I

    JliL I

    ~<8--r=

    I Paul Vaiden fl

    ~=- Uf'l~y'

    ~

    Initials:

    Examiner:

    Level:

    GEReVi ~sy :

    Level:

    ate:

    Initials:

    Examiner 2:

    Level:

    Utility Review:

    ~/

    ANll~J Date: #t*

    Date:

    Page.i. of!

    Initial Cal/Exam Date:

    1111312004

    GE NUCLEAR ENERGY Site/Unit: Oyster Creek I 1 Outage: 1 R20 Ultrasonic Calibration and Examination Record Manual Piping and Components Report Number:

    005296 Data Sheet Number:

    UT-188 Linearity Sheet:

    Jdl!l!

    Calibration Data for Block ASME ALT. BLOCK 3908 Procedure:

    GE-PDl-UT-2 SIS FLAT 1.0*

    Calibration Cal Time Material Size Thick Initial Cal:

    1100 Soundsafe 19620 Cal Check: NIA Coup I ant:

    Couplant batch 235141 70"F Cal Check:

    NIA Thermometer SIN Cal Temp.

    Final Cal:

    1246 DAC Construction Scan Direction Ax NIA NIA Cal Reflector 1.0* Notch NIA NIA Signal Amplitude 80%

    ~

    ~

    Signal Sweep:

    7.0Div

    .ODiv

    .ODiv Signal dB:

    ~.OdB

    .OdB Sweep <l-10 = 2.849/n Metal Path Calibration Verification Field Simulator Block SIN:

    CAL*RHOM-010 Ver I Rev: R3 DRR: NIA Search Unit Data RTD 99-506 2(8x14l mm!Rect Manufacturer:

    Serial Number Size/Shape:

    0.3 in.

    §.Q:

    60*

    Incident Point:

    Nominal Angle:

    Measured Angle:

    2.0MHz TRLA RL

    ~

    Frequency:

    Style:

    Mode:

    Elements:

    Search Unit Cable Q

    RG-174 Cable Type:

    Length:

    Connectors:

    Instrument Settings Panametrics I Eaocb 4 Maufacturer/Model:

    031574612 Serial Number:

    I Reflector FSH NIA Amplitude 80%

    NIA 8.n4us Zero:

    0.2320 in.fusee.

    Velocity:

    0.8

    • 3.0 MHz Narrowband Filter:

    Gain (dB) 36.8 NIA Sweep (SD) 5.4 NIA Acceptable Linearity performed : 10/2512004 Exam Data for Weld: NE-5-0022A Safe End to Elbow (N5Al Configuration:

    OD 84° F 235141 Exam Surface:

    Exam Temp.

    Exam Thermometer Axial I

    Circ AXIAL I

    I UPST DNST DNST Scan dB Recordable 1 Exam Indications I Angle Auto Ful/wave 2.849 in

    ~g./Max Rep"Rate:

    Rectification:

    Range:

    Pulser/Energy:

    4000hms Q

    2.0MHz DUAL Damping:

    Reject:

    Frequency:

    Mode:

    Exam Comments I Limitations:

    Examination.vas perfonned kom the DNST Elbow side only due to Safe End to Elbow configuration Scanned at teference in onler b maintain a 5% to 20% ID 101/.

    No Recordable Indications 1210 Exam End:

    I I

    1---------l----

    +----+------'----1 Exam Start:

    I r?.v' Paul Vaiden Initials:

    Examiner:

    ll Level:

    I~

    "Z'L- -;,~~~

    Level:

    ate:

    Initials:

    Examiner 2:

    Level:

    Date:

    Initial Cal/Exam Date:

    1111312004 11/1:J6'f Date:

    Page ~ of!,

    I I

    '-.J

    " _/

    Wall Thickness Site:

    Oyster Creek Unit:

    1 Report No.:

    GE NUCLEAR ENERGY Profile Sheet Project:

    1BZJl 005296

    . - **~**

    System:

    /so. Cong.

    ~

    ~ 4 Component ID Number:

    NE-5-0022A Position O'

    90' 180' 270'

    [))

    rn 121 r4l

    [§]

    1 NIA NIA NIA NIA Crown Height:

    FLUSH 2

    1 NIA NIA NIA Crown Width:

    1.3" 3

    0.92 NIA NIA NIA

    ~AFEEND ELBOW Nominal Diameter 10/n.

    UPST Component:

    DNST Component:

    4 0.8 NIA NIA NIA Weld Length:

    33.~ln.

    FLow*

    5 0.64 NIA NIA NIA T&C's taken from previous data report no. OCR19-048 dated 10/12/02.

    ~

    <i:.

    I I

    I

    ~v.

    Paul ValfJJl.n l1 1111312004 ~8~--~~

    ANllR~

    tt/?Jft Initials: Examiner:

    Level:

    Date:

    GERevi~y:

    Level:

    Date:

    Utility Review:

    Date:

    Date:

    Page of !

    ,~*

    Report No.:

    EXAMINATION

    SUMMARY

    SHEET OCR20-103 GE NUCLEAR ENERGY Site:

    O]lster Creek Component ID:

    NG-D-0002 Outage:

    1R20 26" Elbow to Pie!

    System Reclrc ASMECat.:

    B-J ASME/tem 89.11 Aug Requirement!

    Exams Perfonned Data Sheet Cal Sheet Procedure Calibration Block Examination Cert Level Date Personnel 45° Shear UT-111 NIA GE-PDl-UT-2 ASMEALT.

    James Williams II 11/9/2004 BLOCK3908 so* Long.

    UT-112 N/A GE-PDl-UT-2 ASME ALT.

    James Williams II 11/9/2004 BLOCK 3908 Examination Results:

    During the manual ultrasonic examination of the above referenced component, no recordable indications were detected.

    One-sided stainless. 50% Coverage per POI.

    This examination meets the requirements of the 1995 Edition of ASME Section XI, 1996 Addenda.

    c Report Number 005334 Examination results were compared to data reoort NIA from N/A Outage With D

    No Change These examinations were performed under Worlc Order:

    C2007461 0

    Change This Summary and the following data sheets have been reviewed and accepted by the following personnel:

    ~~~~

    ~/¢~r c

    Prepared \\

    Level:

    Date:

    w~GJ Date:

    iflr ANll "°"" -~/

    Page 1

    of 4

    Ultrasonic Calibration and Examination Record GE NUCLEAR ENERGY Manual Piping and Components Site/Unit:

    O~ster Creek I 1 Outage: 1R20 Calibration Data for Block ASME ALT. *BLOCK 3908 SIS FL.AT 1.5 Calibration Cal Time Material Size Thick Initial Cal:

    1300 Soundsafe 19620 Cal Check:

    1400 Couplant:

    Couplant batch 235347 68"F Cal Check:

    NIA Thermometer SIN Cal Temp.

    Final Cal:

    1640 DAC Construction Scan Direction Ax NIA NIA Cal Reflector 1.5 Notch NIA NIA Signal Amplitude 80%

    Signal Sweep:

    5.2 Div

    .ODlv

    .ODlv Signal dB:

    1.6dB

    .OdB

    .OdB Sweep 0-10=

    4.000ln M1talPath Calibration Verification Field Simulator Block SIN:

    CAL.-RHOM-018 Reflector FSDH NIA Amplitude 80 NIA Gain (dB) 16.9 NIA Sweep (SD) 2.6 NIA Acceptable Linearity performed : 1012512004 Exam Data for Weld: NG-D-0002 26" Elbow to Ploe Configuration:

    235347 OD Exam Surface:

    70"F Exam Temp.

    Exam Thermometer Axial Circ UPST DNST UPST IJPST James Williams Scan dB 17.6 17.6 Recordable Exam Indications Angle NRI 45*

    NRI 45*

    ll Report Number:

    005334 Data Sheet Number:

    UT-111 Linearity Sheet:

    L.-008 Procedure:

    GE-PDl-UT-2 Ver I Rev: R3 DRR: NIA Search Unit Data KBA OOMPXC 0.50"1Round Manufacturer:

    Serial Number Size/Shape:

    0.35 in.

    45*

    45" Incident Point:

    Nominal Angle:

    Measured Angle:

    1.5MHz Como-G Shear 1

    Frequency:

    Style:

    Mode:

    Elements:

    Search Unit Cable RG-174

    .§:

    Q Cable Type:

    Length:

    Connectors:

    Instrument Settings Panametrics I Ee.och 4 031540306 Maufacturer/Model:

    Serial Number:

    7.773us 0.1230 lnJusec.

    0.8-3.0MHz Zero:

    Velocity:

    Narrowband Filler:

    Fixed Fullwave 4.000ln Sq.I Max I Rep Rate:

    Rectification:

    Range:

    Pulser/Energy:

    4000hms QI[

    2.0MHz PIE Damping:

    Reject:

    Frequency:

    Mode:

    Exam Comments I Limitations:

    145" Shear wave examination noied pravlous non-televant indications countetbore below recordable levels.

    Exam was performed UPST due to pipe cootiguration.

    Exam Start:

    1400 Exam End:

    1445 Examiner:

    Level:

    GE Reviewed By:

    Level:

    Date:

    Initials:

    Examiner 2:

    Level:

    Page ~ of!

    Date:

    ula-M Date:

    Initial Cal/Exam Date:

    111912004

    Ultrasonic Calibration and Examination Record GE NUCLEAR ENERGY Manual Piping and Components Report Number:

    005334 Site/Unit:

    O~ster Creek I 1 Data Sheet Number:

    UT-112 Outage: 1R20 Linearity Sheet:

    L-008 Calibration Data for Block ASME ALT. BLOCK 3908 Procedure: GE-PDl-UT-2 SIS FLAT 1.5 Calibration Cal Time Ver I Rev: R3 ORR: NIA I

    Material Size Thick Initial Cal:

    1300 Search Unit Data Soundsafe 19620 Cal Check:

    1446 RTD 00-343 2(10x18J mmlRect.

    Couplant:

    Couplant batch 235347 68°F Cal Check:

    NIA Manufacturer:

    Serial Number Size/Shape:

    Thermometer SIN Cal Temp.

    Final Cal:

    1640 0.4in.

    60" 60" Incident Point:

    Nominal Angle:

    Measured Angle:

    DAC Construction 2.0MHz TRL2-Aust Long.

    ~

    Scan Direction A!

    NIA NIA Frequency:

    Style:

    Mode:

    Elements:

    Cal Reflector 1.5 Notch NIA NIA Search Unit Cable Signal Amplitude 80%

    ~

    RG-174

    §:

    fl Signal Sweep:

    6.0Div

    .ODlv

    .ODiv Cable Type:

    Length:

    Connectors:

    Signal dB:

    49.1 dB

    .OdB

    .OdB Sweep 0-10=

    5.030in Meta/Path Instrument Settings Calibration Verification Panametrics I E12,och 4 031540306 Maufacturer/Model:

    Serial Number:

    Field Simulator Block SIN:

    CAL-RHOM-018 Reflector 2*Radius NIA 8.899us 0.2259 lnJusec.

    0.8-3.0MHz Amplitude 80 NIA Zero:

    Velocity:

    Narrowband Filter:

    Gain (dB) 27.6 NIA Fixed Fullwave

    ~ Sq.I Max Sweep (SD) 4.0 NIA Rep Rate:

    Rectification:

    Range:

    Pulser/Energy:

    Acceptable Linearity performed : 10/2512004 4000hms Off 2.0MHz PIE Damping:

    Reject:

    Frequency:

    Mode:

    Exam Data for Weld: NG-D-0002 2&- Elbow to P/12,e Exam Comments I Limitations:

    I Conti uration:

    1 No tecon:lable in g

    dications.

    OD 70"F 235347 Exam Surface:

    Exam Temp.

    Exam Thermometer Axial UPST Scan dB Recordable Exam Circ DNST Indications Angle AXIAL UPST 34 NRI 60° 1---------'-------"1----+-------1----1 Exam Start:

    Exam End:

    James Williams

    !l Level:

    Examiner:

    .-w:::.-.

    Level:

    11Jil>)'

    Date:

    I GE R.,,;owed By:

    Initials:

    Examiner 2:

    Level:

    Initial CaUExam Date:

    1119/2004 Date:

    _u/ilfrr Date:

    Page ~ of§.

    '-J

    ' /

    Wall Thickness Site:

    O"s[er Creek Unit:

    1 Report No.:

    GE NUCLEAR ENERGY Profile Sheet Project:

    1R20 005334 System:

    Reel re

    ~

    ~ 4 Component ID Number:

    NG-D-0002 Position o*

    90° 1eo*

    270° llJ

    [TI f21 (41

    [§]

    1 1.35 NIA NIA NIA Crown Height:

    FLUSH 2

    1.3 NIA NIA NIA Crown Width:

    2.0*

    3 1.25 NIA NIA NIA ELBOW PIPE Nominal Diameter l 26/n.

    UPST Component:

    DNST Component:

    4 NIA NIA NIA NIA NIA NIA NIA NIA Weld Length:

    84/n.

    FLOW..,.

    5 J

    I t

    _,/

    \\

    I

    /

    '\\

    /

    /

    ' '\\

    I

    \\

    /

    .,.,,..t(laJ P2Ml P~l/IO(/J. l)f't7'A

    ~~..z;z

    ...,./~,!.,.

    ~¥ 1i?Jr

    ~

    Jamos Wl/llams ll 11.1912004 Examiner:

    Level:

    IJate:

    GE Re:

    By:

    • Level:

    'Date:

    Utility Review:

    Date:

    ANllireVieW Date:

    Page of !

    -

Retrieved from "https://kanterella.com/w/index.php?title=ML15082A163&oldid=5194556"