ML20128E902

Certificate of Compliance 9022,Rev 10,for Model CE-250-2. Approval Record Encl

ML20128E902
Person / Time
Site:	07109022
Issue date:	06/24/1985
From:	Macdonald C NRC OFFICE OF NUCLEAR MATERIAL SAFETY & SAFEGUARDS (NMSS)
To:
Shared Package
ML20128E899	List: ML20128E896 ML20128E902
References
NUDOCS 8507080024
Download: ML20128E902 (4)

Text

4----- F---=&i'immWi4Ziindis-mm-----

. i .

! I NRC FOR2 818 U.S. NUCLEAR REOULATORY C*MMISSION

+an CERTIFICATE OF COMPLlANCE

j io CFR n FOR RADIOACTIVE MATERIALS PACKAGES i ! I a CERTIFICATE NUMBER b REVISION NUMBER c PACKAGE IDENTIFICATION NUMBER d PAGE NUMBER e. TOTAL NUMBER PAGES U 9022 10 USA /9022/AF 1 3 j 2 PREAMBLE

.I a This certificate is issued to certif y that the packaging and Contents described in item $ below, meets the applicable safety standards set forth in Title 10. Code of Federal Regulations. Part 71,' Packaging of Radioactive Materials for Transport and Transportation of Radioactive Material Under Certain Conditions."

! b This certif cate does not relieve the consignor from compliance with any requirement of the regulations of the U S. Department of Transportation or other

-l applicable regulatory agencies, including the government of any country through or into which the package will be transported.

H

' ! 3 THIS CERTIFICATE IS ISSUED ON THE BASIS OF A SAFETY ANALYSIS REPORT OF THE PACKAGE DESIGN OR APPLICATION I a PREPARED BY(Name and AddressA b TITLE AND IDENTIFICATION OF REPORT OR APPLICATION

{

l Combustion Engineering, Inc. Combustion Engineering, Inc. application '

l 1000 Prospect Hill Road dated January 11, 1980, as supplemented.

Windsor, CT 06095 t

c COCKET NUMBER

$ 4 CONDITIONS i This certificate is conditional upon fulfilling the requirements of 10 CFR Part 71, as applecable, and the conditions specified below 1 s- l l

ll (a) Packaging l i I i (1) Model No.: CE-250-2 l (2) Description

l The packaging consists of a 16-gauge steel containment vessel,11-i 5/8 inches ID by 57-1/4 inches long with a bolted and gasketed top i flange closure and steel welded bottom plate. The containment vessel 1

is centered and supported in a 22-1/2-inch ID by 68-3/8-inch long, 16-gauge steel drum by twelve (12),1/4-inch diameter spring steel rods welded to the containment vessel at the top flange and the bottom of

the vessel. The void space between the containment vessel and outer i container is filled with venniculite.

I Closure of the containment vessel is maintained by a gasket (either l silicone rubber or asbestos and rubber) and six (6),1/2-inch hex head l bolts and nuts. The outer container closure is made with a 12-gauge

bolt locking ring with drop forged lugs, one of which is threaded, lj having a 5/8-inch diameter bolt and lock nut.

The gross weight of the packaging and contents is approximately 575 pounds.

1 E

1

E

- li ll a

~i 090 2

'ammmmmmmmmmmmmmmmmmmmmmmmmmmmmmmwmmmmmwwmmmmmmmmmmmmmmm

p --- - -- - -- - ---m -- - - -- - -- -- -- - ------m1EME'!E9EEfEP - -

a i

gf. I gl " '

CcNDITicNS (continu1d) gi I I!

It

! Page 2 - Certificate No. 9022 - Revision No.10 - Docket No. 71-9022 g!

I I!

I!

f (3) Drawing I!

q! The packaging is constructed in accordance with Combustion Engineering I' Company, Inc. Drawing No. NFM-E-Z2175, Revision 02.

H!

[ (b) Contents ,

f (1) Type and form of material N'i l Dry uranium oxide pellets and powder enriched to a maximum 4.1 w/o in Gl the U-235 isotope. -The inaximum H/U atomic ratio, considering all f sources of hydrogenous material within the containment vessel shall yt not exceed 2.26.

• g: ,- . _.

g! (2) Maximum quantity of material per package

• N' i! The total kontents not to exceed 300 pounds, with the U-235 content Ri not to. exceed 4.5 -kilograms. The contents shall be contained within sealed steel containers with a maximun cross sectional area of 73.2 f:

g square inches.  ;

p

, gj

/y Rl , /

1 i>

Nj (c) Fissile Class J. _ _ ,

II Ni ~

i Minimum transport index to be shown on label -

0.6 f,, .

g l

6. The containment vessel closure gaskek -(Item No.12, Drawing No. NFft-E-Z2175, g! Rev. 02) must be made of silicone' rubber,:or an Anchor Packing Company gasket N " Target" or "425."- ,1 s M{- ,t (, s f7.

gi Spacers and produc't containers shall be used to provide.a snug axial fit of the proquet containers within.the containment vessel.

I!

l 8. The package authorized by this certificate is hereby approved for use under the Hl j general license provisions of '10 CFR 571.12.

s

9. Expiration date: June 30,1990.

l Nl:

d 4

R)

H E1 i Ei N E:

1, E:

l E' el' E Hl N il I ,

I l H!

I R

N 1

I

m -m-----

If ' m m--- m mm -----mm m-----m

' -----m m m-m m mmm u- mm m mur7mm mm any lll ll ' CZNolTIONS (continuW; ,

l l!

E (l'

1 Page 3 - Certificate No. 9022 - Revision No.10 - Docket No. 71-9022 E lj N l i i l' p I E

, I REFERENCES g, I I Nl Combustion Engineering, Inc. application dated January 11, 1980.

1 I f

n Supplement dated: June 6, 1980.

i Exxon Nuclear Company supplement dated: May 13, 1981. -

I El FOR THE V.S. NUCLEAR REGULATORY COMf1ISSION I

N!

r ,,,

ql

~

! ,- g ,,,/

I +\ '

Charles E. MacDona d,'ChTef Elj -[t Transportation Certification Branch ll q Division of Fuel Cycle and y , Material Safety, NtiSS.

g _

E Date: JUN2 4 i .s i: I g'

N R; '

\.. L N ,.

q ,

p

~.

y! *

, .:: . l g!

E i n

w .

R s tl- 1 N . 3 g!

g .- <

r n , .

pl  ;

)

i N;

N' E' Nf E a; E d' E N E I E N

I I Ei Hj .

Ni Hi MI N'

i H

I_!

,____________________m__,______-_--_______m-_____-

g[ {94 UNITED STATES F o NUCLEAR REGULATORY COMMISSION 5 p WASHINGTON, D. C. 20555 1

...../

Transportation Certification Branch Approval Record Model No. CE-250-2 Package Docket No. 71-9022 By application dated May 16, 1985, Combustion Engineering, Inc. requested renewal of Certificate of Compliance No. 9022. No changes have been requested or made to the package since approval of the latest supplement dated May 13, 1981.

Combustion Engineering, Inc. has revised the packaging drawing incorporating Conditions 6, 8, and 9 of the present certificate of compliance. Accordingly, Conditions 8 and 9 have been dele +ed from the certificate. However, as a result of reducing the size of the packaging drawing, the gasket infonnation for Item 12 is not legible, therefore, Condition 6 has not been deleted.

The staff concludes that the statements of the original application, as i supplemented, satisfy the requirement for renewal of the certificate of compliance.

Charles E. MacDonald, Chief Transportation Certification Branch Division of Fuel Cycle and Material Safety, NMSS Date: J#l 2 41985