ML20129E057
| ML20129E057 | |
| Person / Time | |
|---|---|
| Site: | 07109022 |
| Issue date: | 05/24/1985 |
| From: | Macdonald C NRC OFFICE OF NUCLEAR MATERIAL SAFETY & SAFEGUARDS (NMSS) |
| To: | |
| Shared Package | |
| ML20129E032 | List: |
| References | |
| NUDOCS 8506060327 | |
| Download: ML20129E057 (4) | |
Text
-- - - - - -- JA K-- -- - EA i---- -- - a a -- ----- hsi i------N iim- -- inas.
Ip73 CERTIFICATE OF COMPLIANCE I; io CFa "
FOR RADl! ACTIVE MATERIALS PACKA"ES I
i t a CERTIFICATE NUMBER D REVISION NUMBER c PACKAGE IDENTIFICATION NUMBER d PAGE NUMBER e TOTAL NUMBER PAGE0 g!
9022 9
USA /9022/AF 1
3 g
h
- 2. PREAMBLE k
l;
- a. This certificate is issued to certify that the packaging and contents desenbed in item 5 below, meets theapplecable safety standards set forth in Title 10. Code l
g! -
of Federal Regulations. Part 71. Packaging of Radioactive Matenals for Transport and Transportatson of Radioactive Material Under Certain Conditions."
g I
- b. Thes certificate does not reheve the consignor from comphance with any requirement of the regulations of the U S. Department of Transportation or other
- N ll apphcable regulatory agencies, including the government of any country through or into which the package will be transported.
k I!
E-Il l'
I E.
- 3. THIS CERTIFICATE IS ISSUED ON THF BASIS OF A SAFETY ANALYSIS REPORT OF THE PACKAGE DESIGN OR APPLICATION i
a, PREPARED BY (Name and Adctress, b TITLE AND IDENTIFICATION OF REPORT OR APPLICATION
{
ll Combustion Engineering Co., Inc.
Combustion Engineering, Inc. application K.
Ej 1000 Prospect Hill Road dated January ll,1980, as supplemented.
E-I, Windsor, CT 06095 N
71-9022 4
I:
(
l c DOCKET NUMBER 4 CONDITIONS J
This certificate is conditional upon fulfilling the requirements of to CFR Part 71, as applicable, and the conditions specified below ll s-ti d;
l '-
gl (a) Packaging t
r i
I (1) Model No.:
CE-250-2 N
1 R!
f (2) Description f
d' N
g!
The, ekaging consists of a 16-gauge steel containment vessel,11-I ll 5/8 in.hes ID by 57-1/4 inches long with a bolted and gasketed top N
I flange closure and steel welded botton plate.
The containment vessel N
ll 1s centered and supported in a 22-1/2-inch ID by 68-3/8-inch long,16-l l
g!
gauge steel drum by twelve (12),1/4-inch diameter spring steel rods g
gl welded to the containment vessel at the top flange and the bottom of p
the vessel.
The void space between the containment vessel and outer i
g!I container is filled with vemiculite.
I I!
I k
Closure of the containment vessel is maintained by a gasket (either N
silicone rubber or asbestos and rubber) and six (6),1/2-inch hex head h
([
bolts and nuts. The outer container closure is made with a 12-gauge W
pll; bolt locking ring with drop forged lugs, one of which is threaded, I
'H having a 5/8-inch diameter bolt and lock nut.
I E!
N f
The gross weight of the packaging and contents is approximately 575 l
g pounds.
g g!
I I
I E
I N
I!
I I;
I I!
5.
I!
W si i
Rl 1
i:
i I!
I N!
N-NI B506060327 850524 E
I't C
PDR N
N lll l
...--------------------------n
m m3nrLu-
^^
)
C NDITIONS(continued) l 1
N l
Page 2 - Certificate No. 9022 - Revision No. 9 - Docket No.
l 71-9022 1
l I
N I
I j
(3) Drawing I
l The packaging is constructed in accordance with Combustion Engineering l
~
1 Company, Inc. Drawing No. NFM-E-Z2175, Revision 00.
g 1
R 1
(b) Contents i
1 i
f (1) Type and form of material l
f Dry uranium oxide pellets and powder enriched to a maximum 4.1 w/o in h
ll l
the U-235 isotope. The, maximum H/U atomic ratio, considering all e
sources of hydrogenous material within;the containment vessel shall i
Ji not exceed 2.26.
V U.
I
(,e
-q j
ll; (2) Maximum quantity of material per package J
p, g
1:
i' f
1l The totalJcontents not to exceed 300 pounds, with the U-235 content i
1 not to exceed 4.5 kilograms. The contents shall-be contained within i
1 sealed steel containers with a maximum cross sectional area of 73.2 i
f square' inches.
N f rL l
+ h,f z
n',
If-p 1:
r-
/
\\j L,.
ll (c) Fissile Class II p
]
i j
a,.
s.
cr..3
./-
1 Minimum transport index. to be shown on label 0.6 5
]
i 3r,;
i yr The containment ' vessel closure gashe;t (Item!No.12,' Drawing No. NFN-E-Z2175, l
m 6.
j.
1!
Rev. 00) must be made of Jsilicone rubber, or an Anchor Packing Company gasket y
' ; ~ 1/
N 1j
" Target" or "425.",i y n, J
s-r,
.o o
p 1
7.
Spacers and product-containers 'shall.bs'used to provide afsnug axial fit of the I
]!
product containers within the containmentLvessel.'"
(
l 7
j! -
8.
Attachment of handle (Item 18, Drawing No. NFM-EZ2175) to outer lid is not p
m y
4
]
1l 1
authorized.
a p
't i
3 I
1 Alternate closure system shown in Figure 1 of Exxon Nuclear Company, Inc. letter I
[
9.
l dated August 14, 1980 is authorized.
Jt I
lj
- 10. The package authorized by this certificate is hereby approved for use under the y
1 general license provisions of 10 CFR 671.12.
p 1
1 11.
Expiration date:
September 30, 1985.
I 1
a 1
I l,
i j
lj l
lq I
i lj i
1, i
1 i
1; e
l; I
i lj I
lj N
1 p
n
,--------AAA-----------------------------------------$
CONDITEONs (continua) l l!
I h
Page 3 - Certificate No. 9022 - Revision No. 9 - Docket No. 71-9022 1
I L
I J:
lt REFERENCES j
i
>l E
Jl Combustion Engineering, Inc. application dated January 11, 1980.
1 li Il 4
3; Supplement dated:
June 6, 1980.
(
1 t
Jl Exxon Nuclear Company supplement dated: May 13, 1981.
[
l E
1l l
FOR THE U.S. NUCLEAR REGULATORY COMMISSION tl t-1l
?l r
p { {- /j/
N 1;
u - s e
m 1;
te.
t:
l p\\'
s g2 I1; s*>
Charles E. MacDonald, Chief t-1
- ?
Transportation Certification Branch ti f
e Division of Fuel Cycle and i
Material Safety, f#iSS.
[
q!
NAY24 25 l
- 'x 4
L' l
Date:
N L:
j t;
I, s
l ?
t:
l!
s 1) t
,L t
3 3
1l t
1 g-1
'T
~
L:
l j
s y
g-e t
.t o
t:
1.
c' '
x.
t:
s ll t
ll t-lj i.
L t-s Jl
!.i ',
t.
I t-t Jj t-li t
lj 4
t 1
3 t
l,i
[
1 I
I I
l E
l{i E
1 1;
1 f
1
[
l i
il i
i J.
E l'
t ilj l
1l I
l 5
lj B-1, t
l! -
I t
a 1l l
lo l
1 1
_I!_- ______--________________________________________-,_,p,.
'o,,
UNITED STATES
_8 NUCLEAR REGULATORY COMMISSION o
O j
WASHINGTON, D. C. 20555 "s.,...../
Transportation Certification Branch Approval Record Model No. CE-250-2 Package Docket No. 71-9022 By application dated May 20, 1985, Exxon Nuclear Company, Inc. has requested that the expiration date for Certificate of Compliance No. 9022 he extended from June 30, 1985 to September 30, 1985. This would allow time to permit the Combustion Engineering Company to request renewal of the package without interrupting foreign shipments in the package by Exxon Nuclear Company.
Charles E. Macbonald, Chief Transportation Certification Branch Division of Fuel Cycle and Material Safety, NMSS Date: MM 2 41985
.