CNL-16-001, Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02): Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(Created page by program invented by StriderTol)
 
(2 intermediate revisions by the same user not shown)
Line 3: Line 3:
| issue date = 05/26/2016
| issue date = 05/26/2016
| title = Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)
| title = Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)
| author name = Shea J W
| author name = Shea J
| author affiliation = Tennessee Valley Authority
| author affiliation = Tennessee Valley Authority
| addressee name =  
| addressee name =  
Line 16: Line 16:


=Text=
=Text=
{{#Wiki_filter:Tennessee Valley Authority, 1101 Market Street, Chattanooga, Tennessee 37402 CNL-16-001 May 26, 2016  
{{#Wiki_filter:Tennessee Valley Authority, 1101 Market Street, Chattanooga, Tennessee 37402 CNL-16-001 May 26, 2016 10 CFR 50.90 U.S. Nuclear Regulatory Commission ATTN: Document Control Desk Washington, D.C. 20555-0001 Sequoyah Nuclear Plant Units 1 and 2 Renewed Facility Operating License Nos. DPR-77 and DPR-79 NRC Docket Nos. 50-327 and 50-328
 
10 CFR 50.90 U.S. Nuclear Regulatory Commission ATTN: Document Control Desk Washington, D.C. 20555-0001  
 
Sequoyah Nuclear Plant Units 1 and 2   Renewed Facility Operating License Nos. DPR-77 and DPR-79 NRC Docket Nos. 50-327 and 50-328  


==Subject:==
==Subject:==
Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)
Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)
In accordance with the provisions of Title 10 of the Code of Federal Regulations (10 CFR) 50.90, "Application for amendment of license, construction permit, or early site permit,"
In accordance with the provisions of Title 10 of the Code of Federal Regulations (10 CFR) 50.90, "Application for amendment of license, construction permit, or early site permit,"
Tennessee Valley Authority (TVA) is submitting a request for an amendment (SQN-TS-14-02) to Renewed Facility Operating License Nos. DPR-77 and DPR-79 for the Sequoyah Nuclear Plant (SQN) Units 1 and 2.  
Tennessee Valley Authority (TVA) is submitting a request for an amendment (SQN-TS-14-02) to Renewed Facility Operating License Nos. DPR-77 and DPR-79 for the Sequoyah Nuclear Plant (SQN) Units 1 and 2.
 
This license amendment request proposes to amend the SQN Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. Currently, the acceptance criteria are 58.8 Hz and  61.2 Hz. TVA proposes to change the SQN DG steady state frequency acceptance criteria to  59.8 Hz and  60.2 Hz. The DG TS SR steady state voltage range of  6800 V and  7260 V is unaffected.
This license amendment request proposes to amend the SQN Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. Currently, the acceptance criteria are 58.8 Hz and  61.2 Hz. TVA proposes to change the SQN DG steady state frequency acceptance criteria to  59.8 Hz and  60.2 Hz. The DG TS SR steady state voltage range of  6800 V and  7260 V is unaffected.
TVA has determined that the steady state frequency range acceptance criteria currently specified by SQN TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are non-conservative. A Condition Report (CR) was initiated in accordance with the TVA Corrective Action Program. Subsequently, a prompt determination of operability (PDO),
TVA has determined that the steady state frequency range acceptance criteria currently specified by SQN TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are non-conservative. A Condition Report (CR) was initiated in accordance with the TVA Corrective Action Program. Subsequently, a prompt determination of operability (PDO),
including administrative controls were established in accordance with the Nuclear Regulatory Commission (NRC) Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998. As a result of the CR, a number of immediate/interim and other corrective actions were identified, implemented, and completed. A review of historical DG test records for frequency and voltage supported the fact that the DGs were operable and supported the existing design basis analyses accidents. Administrative controls for DG frequency have been implemented in the applicable Surveillance Instructions to support continued DG operability.    
including administrative controls were established in accordance with the Nuclear Regulatory Commission (NRC) Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998. As a result of the CR, a number of immediate/interim and other corrective actions were identified, implemented, and completed. A review of historical DG test records for frequency and voltage supported the fact that the DGs were operable and supported the existing design basis analyses accidents. Administrative controls for DG frequency have been implemented in the applicable Surveillance Instructions to support continued DG operability.


U.S. Nuclear Regulatory Commission CNL-16-001  
U.S. Nuclear Regulatory Commission CNL-16-001 Page 2 May 26, 2016 The enclosure to this letter provides a description of the proposed changes, technical evaluation of the proposed changes, regulatory evaluation, and a discussion of environmental considerations. Attachments 1 and 2 to the enclosure provide the existing TS and Bases pages marked-up to show the proposed changes. Attachments 3 and 4 to the enclosure provide the existing TS and Bases pages retyped to show the proposed changes. Changes to the existing TS Bases, are provided for information only and will be implemented under the Technical Specification Bases Control Program.
As noted in the enclosure, the modified SR 3.8.1.9 is normally performed during outages.
Therefore, TVA requests NRC approval of this proposed license amendment by May 2017 with implementation during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy the revised SR 3.8.1.9 prior to implementation of this proposed license amendment.
TVA has determined that there are no significant hazard considerations associated with the proposed change and that the change qualifies for a categorical exclusion from environmental review pursuant to the provisions of 10 CFR 51 .22(c)(9).
The SQN Plant Operations Review Committee and the TVA Nuclear Safety Review Board have reviewed this proposed change and determined that operation of SQN Units 1 and 2 in accordance with the proposed change will not endanger the health and safety of the public.
In accordance with 10 CFR 50.91(b)(1), TVA is sending a copy of this letter and the enclosure to the Tennessee Department of Environment and Conservation.
There are no new regulatory commitments associated with this submittal. Please address any questions regarding this request to Ed Schrull at (423) 751-3850.
I declare under penalty of perjury that the foregoing is true and correct. Executed on this 26th day of May 2016.
President, Nuclear Licensing Enclosure cc: See Page 3


Page 3 May 26, 2016  
U.S. Nuclear Regulatory Commission CNL-16-001 Page 3 May 26, 2016 RDW: EDS
 
RDW: EDS  


==Enclosure:==
==Enclosure:==
Evaluation of Proposed Change cc (Enclosure):
Evaluation of Proposed Change cc (Enclosure):
NRC Regional Administrator - Region II NRC Senior Resident Inspector - Sequoyah Nuclear Plant NRR Project Manager - Sequoyah Nuclear Plant Director, Division of Radiological Health - Tennessee State Department of Environment and Conservation  
NRC Regional Administrator - Region II NRC Senior Resident Inspector - Sequoyah Nuclear Plant NRR Project Manager - Sequoyah Nuclear Plant Director, Division of Radiological Health - Tennessee State Department of Environment and Conservation


CNL-16-001 E1 of 20 
ENCLOSURE TENNESSEE VALLEY AUTHORITY SEQUOYAH NUCLEAR PLANT UNITS 1 AND 2 EVALUATION OF PROPOSED CHANGE


==Subject:==
==Subject:==
1.0  
Application to Modify Sequoyah Nuclear Plant Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02) 1.0


==SUMMARY==
==SUMMARY==
DESCRIPTION 2.0 DETAILED DESCRIPTION 2.1   Proposed Change 2.2   Need for Proposed Changes
DESCRIPTION 2.0 DETAILED DESCRIPTION 2.1     Proposed Change 2.2     Need for Proposed Changes 2.3     Implementation
 
2.3   Implementation
 
==3.0 TECHNICAL EVALUATION==


3.1  System Description
==3.0  TECHNICAL EVALUATION==


3.2   Evaluation
3.1    System Description 3.2     Evaluation 3.3    Conclusion


3.3  Conclusion
==4.0  REGULATORY EVALUATION==


==4.0 REGULATORY EVALUATION==
4.1    Applicable Regulatory Requirements and Criteria 4.2    Precedent 4.3    Significant Hazards Consideration 4.4    Conclusion


4.1 Applicable Regulatory Requirements and Criteria  4.2 Precedent 4.3 Significant Hazards Consideration
==5.0  ENVIRONMENTAL CONSIDERATION==


4.4 Conclusion
==6.0 REFERENCES==
 
==5.0 ENVIRONMENTAL CONSIDERATION==
 
==6.0 REFERENCES==


ATTACHMENTS
ATTACHMENTS
: 1. Proposed TS Changes (Mark
: 1. Proposed TS Changes (Mark-Ups) for SQN Units 1 and 2
-Ups) for SQN Units 1 and 2
: 2. Proposed TS Bases Changes (Mark-Ups) for SQN Units 1 and 2 (For Information Only)
: 2. Proposed TS Bases Changes (Mark
-Ups) for SQN Units 1 and 2 (For Information Only)
: 3. Proposed TS Changes (Final Typed) for SQN Units 1 and 2
: 3. Proposed TS Changes (Final Typed) for SQN Units 1 and 2
: 4. Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)
: 4. Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)
CNL-16-001                              E1 of 20


ENCLOSURE   CNL-16-001 E2 of 20  The Tennessee Valley Authority (TVA) is requesting a license amendment to amend the Sequoyah Nuclear Plant (SQN) Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in SQN Units 1 and 2, TS 3.8.1, "AC Sources - Operating.
ENCLOSURE 1.0    
"  Specifically, the proposed change and supporting evaluation will modify the acceptance criteria for the DG steady state frequency range provided in SQN Units 1 and 2 TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. Currently, the DG SR steady state acceptance criteria are  . TVA proposes to change the SQN DG steady state frequency acceptance criteria to 59.8 Hz and 0.2 Hz. The DG TS SR steady state voltage range of  6800 V and 7260 V is not affected. This license amendment request (LAR) is similar to a Watts Bar Nuclear Plant (WBN) Unit 1 submittal (Reference 1), which was approved by the NRC in Reference 2.
This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs o f TS 3.8.1 to be performed
. However, no specific changes to SR 3.8.1.3 or TS 3.8.2 are required.
Currently, the acceptance criteria for DG steady state frequency specified in SQN Units 1 and 2, TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are z and 1.2 Hz. TVA proposes to conservatively narrow the DG 59.8 Hz and decreasing the current upper limit from the existing 1.2 Hz to  60.2 Hz in the SQN Units 1 and 2 TS 1 (i.e., SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18) and TS Bases 3.8.1. The proposed SQN Units 1 and 2 DG frequency and voltage steady state operating range s only apply to the steady state condition of DG operation, and are summarized below in Table 1.
9.8 Hz to 0.2 Hz 6800 V to 7260 V  This change is applicable to the surveillance s performed at 31 days, 18 month s, and ten year s when maintenance & test equipment (M&TE) is installed on the DG per the surveillance instructions.


==SUMMARY==
DESCRIPTION The Tennessee Valley Authority (TVA) is requesting a license amendment to amend the Sequoyah Nuclear Plant (SQN) Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in SQN Units 1 and 2, TS 3.8.1, "AC Sources - Operating. Specifically, the proposed change and supporting evaluation will modify the acceptance criteria for the DG steady state frequency range provided in SQN Units 1 and 2 TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18.
Currently, the DG SR steady state acceptance criteria are  58.8 Hz and  61.2 Hz.
TVA proposes to change the SQN DG steady state frequency acceptance criteria to 59.8 Hz and  60.2 Hz. The DG TS SR steady state voltage range of  6800 V and 7260 V is not affected. This license amendment request (LAR) is similar to a Watts Bar Nuclear Plant (WBN) Unit 1 submittal (Reference 1), which was approved by the NRC in Reference 2.
This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed.
However, no specific changes to SR 3.8.1.3 or TS 3.8.2 are required.
2.0    DETAILED DESCRIPTION 2.1    Proposed Changes Currently, the acceptance criteria for DG steady state frequency specified in SQN Units 1 and 2, TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are  58.8 Hz and  61.2 Hz. TVA proposes to conservatively narrow the DG frequency range by increasing the current DG frequency lower limit of  58.8 Hz to 59.8 Hz and decreasing the current upper limit from the existing  61.2 Hz to  60.2 Hz in the SQN Units 1 and 2 TS1 (i.e., SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18) and TS Bases 3.8.1. The proposed SQN Units 1 and 2 DG frequency and voltage steady state operating ranges only apply to the steady state condition of DG operation, and are summarized below in Table 1.
Table 1 Technical Specification DG Steady-State Operating Range Parameter                                      Range Frequency                              59.8 Hz to  60.2 Hz Voltage                                6800 V to  7260 V This change is applicable to the surveillances performed at 31 days, 18 months, and ten years when maintenance & test equipment (M&TE) is installed on the DG per the surveillance instructions.
1 Note: No change is required to SQN Units 1 and 2, TS SR 3.8.1.19 because that surveillance does not apply to steady state operation.
1 Note: No change is required to SQN Units 1 and 2, TS SR 3.8.1.19 because that surveillance does not apply to steady state operation.
CNL-16-001                                    E2 of 20
ENCLOSURE The DG voltage limits as described in the Technical Specifications are correct and do not require revision.
Attachments 1 and 2 to this enclosure provide the existing SQN Units 1 and 2 TS and Bases pages marked-up to show the proposed changes. Attachments 3 and 4 to this enclosure provide the clean typed TS and Bases pages with the proposed changes incorporated.
The proposed Bases changes are provided to the NRC for information only.
2.2  Need for Proposed Changes Plant safety analyses make specific assumptions regarding the emergency core cooling system (ECCS) flow to provide the core cooling function following any event that requires safety injection (SI) to mitigate the event. For the events that assume a loss of offsite power (LOOP), the DGs provide power to the ECCS pumps. Following a LOOP, each DG starts and ties to an engineered safety feature (ESF) board, and essential loads, including the ECCS pumps, are sequentially connected to the ESF board by individual timers for each load sequence. The calculated ECCS flow rates assume that the steady state DG frequency is 60 Hz (i.e., after the DG starting and loading transients).
Once the DG starting and loading sequences are complete, the DG governor maintains the frequency at 60 Hz within a specified tolerance, which is based on the governor manufacturer/model.
The ECCS flow provided by the ECCS pumps is affected by the pump speed, which in turn is a function of the DG frequency. Historically, the DG frequency tolerances associated with the governor were not considered in the development of the ECCS, containment spray system (CSS), and auxiliary feedwater (AFW) flow rates. The primary effect of changes in DG frequency on the ECCS safety functions is an increase or decrease in the speed of safety-related motors that are powered by the DG. The increase or decrease in the speed of the motors affects pump performance, motor operated valve (MOV) stroke times, cooling fan performance, and DG loading, among other factors.
The minimum and maximum frequency values of 58.8 Hz and 61.2 Hz in the SQN TS SRs are equal to +/- 2% of the 60 Hz nominal frequency (i.e., the TS specified plant specific transient range). However, the +/- 2% frequency tolerance is only applicable to DG starting and loading transients, and does not apply to steady state operation as discussed in Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies" (Reference 3).
Because the safety analyses did not consider the effects of operating at the extremes of the steady state frequency range specified in TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18, TVA has determined that the current SQN Units 1 and 2 TS SR acceptance criteria for steady state DG frequency are non-conservative. The non-conservative acceptance criteria were addressed within the TVA corrective action program (CAP) and administrative controls were established in accordance with NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety" (Reference 4). To address the non-conservative TS, CNL-16-001                                  E3 of 20
ENCLOSURE TVA is proposing a change to TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 to revise the DG SR steady state acceptance criteria to  59.8 Hz and  60.2 Hz.
The four SQN DGs are shared between SQN Units 1 and 2, as described in Section 3.1, and the SRs for all four DGs are specified in the SQN Units 1 and 2 TSs. Therefore, the proposed SR steady state frequency acceptance criteria of  59.8 Hz and  60.2 Hz would apply to all four DGs.
2.3  Implementation The TVA process governing the preparation and submittal of TS changes and LARs requires that the appropriate organizations (e.g., Operations, Training, Engineering, Maintenance, Chemistry, Radiation Protection, and Work Control) identify the documents that are affected by each proposed change to the TSs and Operating Licenses. Among the items that are considered are training, plant modifications, procedures, special implementation constraints, design documents, and surveillance instructions associated with TS SRs, Technical Requirements Manual, TS Bases, and the Updated Final Safety Analysis Report (UFSAR). The process requires that procedures and design document changes necessary to support TS Operability are approved prior to implementation of an NRC approved license amendment. The process also provides assurance that the remaining changes, if any, are scheduled and tracked for configuration control.
SR 3.8.1.9 requires verification that each DG can maintain acceptable frequency following a load rejection greater than or equal to the single largest post-accident load.
This SR includes verification that the DG can restore frequency within the allowable steady-state band within three seconds. SQN currently performs SR 3.8.1.9 concurrent with SR 3.8.1.10, which verifies that the DG can withstand a full load rejection (from a fully loaded condition). This approach is acceptable because the full load rejection of SR 3.8.1.10 as well as the single largest post-accident load requirement of SR 3.8.1.9 are performed. The current test methodology for both SR 3.8.1.9 and 3.8.1.10 requires the DG to initially be in parallel with offsite power to achieve the required power value.
When the DG is operating in parallel with offsite power for surveillance testing, the speed droop circuit in the DG speed governor is required to be in service (i.e., non-emergency /
droop test mode). The speed droop function is necessary to ensure stable and controllable load-sharing between the DG and offsite power. However, the speed droop results in a steady-state frequency greater than the nominal 60 Hz value following a load rejection. Historical data shows that DG frequency typically stabilizes at approximately 60.3 Hz following a single largest load rejection with speed droop in service. This final frequency value is acceptable under the current SR 3.8.1.9, but is outside the more stringent frequency criteria proposed in this LAR. These results are due to the surveillance test methodology (i.e., performing the load rejection with the speed droop circuit in service) rather than being an indication of a problem or malfunction in the DG speed governor.
CNL-16-001                                    E4 of 20


ENCLOSURE   CNL-16-001 E3 of 20  The DG voltage limits as described in the Technical Specification s are correct and do not require revision. Attachments 1 and 2 to this enclosure provide the existing SQN Units 1 and 2 TS and Bases pages marked
ENCLOSURE To successfully perform SR 3.8.1.9 with the more conservative frequency band proposed in this LAR, the test methodology must be modified to perform the load rejection with the DG in accident mode (emergency / isochronous mode) and isolated on the shutdown board (i.e., not initially in parallel with offsite power). In the accident mode, the DG speed governor uses a fixed speed reference corresponding to 60.0 Hz, which ensures that the frequency criteria of SR 3.8.1.9 can be met. This requires a revision to the surveillance test procedures to perform SR 3.8.1.9 in conjunction with SR 3.8.1.18 (shutdown board blackout testing). This change in methodology is beneficial because it more closely replicates the conditions under which the DGs may have to perform following a loss of offsite power. TVA has initiated action to ensure that the applicable surveillance testing procedures are revised to incorporate this change prior to the next unit refueling outage on each SQN unit. Because the modified SR 3.8.1.9 is normally performed during outages, TVA is requesting implementation of this proposed license amendment during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy revised SR 3.8.1.9 prior to implementation of this proposed license amendment.
-up to show the proposed changes.
Attachments 3 and 4 to this enclosure provide the clean typed TS and Bases pages with the proposed changes incorporated
. The proposed Bases changes are provided to the NRC for information only.
Plant safety analyses make specific assumptions regarding the emergency core cooling syst em (ECCS) flow to provide the core cooling function following any event that requires safety injection (SI) to mitigate the event.
For the events that assume a loss of offsite power (LOOP), the DGs provide power to the ECCS pumps.
Following a LOOP, each DG starts and ties to an engineered safety feature (ESF) board, and essential loads, including the ECCS pumps, are sequentially connected to the ESF board by individual timers for each load sequence. The calculated ECCS flow rates assume that the steady state DG frequency is 60 Hz (i.e., after the DG starting and loading transients). Once the DG starting and loading sequences are complete, the DG governor maintains the frequency at 60 Hz within a specified tolerance, which is based on the governor manufacturer/model. The ECCS flow provided by the ECCS pumps is affected by the pump speed, which in turn is a function of the DG frequency.
Historically, the DG frequency tolerances associated with the governor were not considered in the development of the ECCS, containment spray system (CSS), and auxiliary feedwater (AFW) flow rates. The primary effect of changes in DG frequency on the ECCS safety functions is an increase or decrease in the speed of safety
-related motors that are powered by the DG. The increase or decrease in the speed of the motors affects pump performance, motor operated valve (MOV) stroke times, cooling fan performance, and DG loading, among other factor s. The minimum and maximum frequency values of 58.8 Hz and 61.2 Hz in the SQN TS SRs are equal to +/-
2% of the 60 Hz nominal frequency (i.e., the TS specified plant specific transient range
). However, the +/-
2% frequency tolerance is only applicable to DG starting and loading transients, and does not apply to steady state operation as discussed in Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies" (Reference 3). Because the safety analyses did not consider the effects of operating at the extremes of the steady state frequency range specified in TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18, TVA has determined that the current SQN Units 1 and 2 TS SR acceptance criteria for steady state DG frequency are non
-conservative. The non-conservative acceptance criteria were addressed within the TVA corrective action program (CAP) and administrative controls were established in accordance with NRC Administrative Letter 98
-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety" (Reference 4). To address the non
-conservative TS, ENCLOSURE    CNL-16-001 E4 of 20  TVA is proposing a change to TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 to revise the DG SR steady state acceptance criteria to 9.8 Hz and 0.2 Hz. The four SQN DGs are shared between SQN Units 1 and 2, as described in Section 3.1, and the SR s for all four DGs are specified in the SQN Units 1 and 2 TS s. Therefore, the proposed SR steady state frequency acceptance criteria of 9.8 Hz and 0.2 Hz would apply to all four DGs. The TVA process governing the preparation and submittal of TS changes and L AR s requires that the appropriate organizations (e.g., Operations, Training, Engineering, Maintenance, Chemistry, Radiation Protection, and Work Control) identify the documents that are affected by each proposed change to the TSs and Operating Licenses. Among the items that are considered are training, plant modifications, procedures, special implementation constraints, design documents, and surveillance instructions associated with TS SRs, Technical Requirements Manual, TS Bases, and the Updated Final Safety Analysis Report (UFSAR). The process requires that procedures and design document changes necessary to support TS Operability are approved prior to implementation of an NRC approved license amendment. The process also provides assurance that the remaining changes, if any, are scheduled and tracked for configuration control.
SR 3.8.1.9 requires verification that each DG can maintain acceptable frequency following a load rejection greater than or equal to the single largest post
-accident load. This SR includes verification that the DG can restore frequency within the allowable steady-state band within three seconds. SQN currently performs SR 3.8.1.9 concurrent with SR 3.8.1.10, which verifies that the DG can withstand a full load rejection (from a fully loaded condition). This approach is acceptable because the full load rejection of


SR 3.8.1.10 as well as the "single largest post
==3.0   TECHNICAL EVALUATION==
-accident load" requirement of SR 3.8.1.9 are performed. The current test methodology for both SR 3.8.1.9 and 3.8.1.10 requires the DG to initially be in parallel with offsite power to achieve the required power value.
When the DG is operating in parallel with offsite power for surveillance testing, the speed droop circuit in the DG speed governor is required to be in service (i.e., non-emergency / droop test mode). The speed droop function is necessary to ensure stable and controllable load
-sharing between the DG and offsite power. However, the speed droop results in a steady
-state frequency greater than the nominal 60 Hz value following a load rejection. Historical data shows that DG frequency typically stabilizes at approximately 60.3 Hz following a single largest load rejection with speed droop in service. This final frequency value is acceptable under the current SR 3.8.1.9, but is outside the more stringent frequency criteria proposed in this LAR. These results are due to the surveillance test methodology (i.e., performing the load rejection with the speed droop circuit in service) rather than being an indication of a problem or malfunction in the DG speed governor.
ENCLOSURE    CNL-16-001 E5 of 20   To successfully perform SR 3.8.1.9 with the more conservative frequency band proposed in this LAR, the test methodology must be modified to perform the load rejection with the DG in accident mode (emergency /
isochronous mode) and isolated on the shutdown board (i.e., not initially in parallel with offsite power). In the accident mode, the DG speed governor uses a fixed speed reference corresponding to 60.0 Hz, which ensures that the frequency criteria of SR 3.8.1.9 can be met. This requires a revision to the surveillance test procedures to perform SR 3.8.1.9 in conjunction with SR 3.8.1.18 (shutdown board blackout testing
). This change in methodology is beneficial because it more closely replicates the conditions under which the DGs may have to perform following a loss of offsite power. TVA has initiated action to ensure that the applicable surveillance testing procedures are revised to incorporate this change prior to the next unit refueling outage on each SQN unit. Because the modified SR 3.8.1.9 is normally performed during outages, TVA is requesting implementation of this proposed license amendment during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy revised SR 3.8.1.9 prior to implementation of this proposed license amendment. The onsite Class 1E alternating current (AC) standby system is described in SQN UFSAR Section 8.3, "Onsite Power System." As noted in SQN UFSAR Section 8.3, the onsite AC power system is a Class 1E system, which consists of the standby AC power system and the 120 V vital AC system. The standby AC power system is a safety
-related system, which supplies power for energizing all AC
-powered electrical devices essential to safety. The safety function of the s tandby AC power system is to supply power to permit functioning of components and systems required to assure that: (1) fuel design limits and reactor coolant pressure boundary design conditions are not exceeded due to anticipated operational occurrences, and (2) the core is cooled and vital functions are maintained in the event of a postulated accident, subject to loss of the preferred power system and subject to any single failure in the standby power system.
Specifically, the standby AC power system includes:  four Class 1E DGs (designated 1A-A, 1B-B, 2A-A, and 2B-B)  four 6.9 kV shutdown boards and logic relay panels associated 6.9 kV/480 V transformers and 480 V shutdown boards motor control centers supplied by the 480 V shutdown boards The AC standby power system is divided into two redundant load groups (power trains). The 6.9 kV shutdown boards are arranged electrically into two power trains with two boards associated with each train and each unit.
The boards comprising train A are located in the SQN Uni t 1 side and those of train B are located in the SQN Unit 2 side. The train A boards are separated from the train B boards by a reinforced concrete block wall, which is a qualified fire barrier, extended to the ceiling. When the preferred (offsite) power system is not available, each shutdown board is energized from a separate standby DG.


ENCLOSURE    CNL-16-001 E6 of 20   A loss of voltage on the 6.9 kV shutdown board starts the associated DG and initiates logic that trips the supply feeder breakers, all 6.9 kV loads (except the 480 V shutdown board transformers), and the major 480 V loads. The bypass breaker for the 480 V shutdown board's current
3.1  System Description The onsite Class 1E alternating current (AC) standby system is described in SQN UFSAR Section 8.3, "Onsite Power System.
-limiting inductive reactor is also closed as part of this logic. When the DG has reached rated speed and voltage, the generator is automatically connected to the 6.9 kV shutdown board. This return of voltage to the 6.9 kV shutdown board initiates logic that connects the required loads in sequence. The standby (onsite) power system's automatic sequencing logic is designed to automatically connect the required loads in proper sequence should the logic receive an accident signal prior to, concurrent with, or following a loss of all nuclear unit and preferred (offsite) power.
As noted in SQN UFSAR Section 8.3, the onsite AC power system is a Class 1E system, which consists of the standby AC power system and the 120 V vital AC system. The standby AC power system is a safety-related system, which supplies power for energizing all AC-powered electrical devices essential to safety. The safety function of the standby AC power system is to supply power to permit functioning of components and systems required to assure that: (1) fuel design limits and reactor coolant pressure boundary design conditions are not exceeded due to anticipated operational occurrences, and (2) the core is cooled and vital functions are maintained in the event of a postulated accident, subject to loss of the preferred power system and subject to any single failure in the standby power system.
As noted in UFSAR Section 8.3.1.1 , there are two loading sequences: "One, which is applied in the absence of a safety injection signal (SIS), the 'non-accident condition,' and the other 'accident condition,' applied when an SIS (and containment spray actuation signal) is received coincident with a sustained loss of voltage on the 6.9 kV shutdown board.
Specifically, the standby AC power system includes:
A loss of offsite power coincident with an SIS is the design basis event; however, as noted in UFSAR Section 8.3.1.1, an SIS received during the course of a non
* four Class 1E DGs (designated 1A-A, 1B-B, 2A-A, and 2B-B)
-accident shutdown loading sequence would cause the actions described below.
* four 6.9 kV shutdown boards and logic relay panels
: 1. "Loads already sequentially connected that are not required for an accident will be disconnected (except fire pumps powered by the DG). 2. Loads already sequentially connected that are required for an accident will remain connected.
* associated 6.9 kV/480 V transformers and 480 V shutdown boards
* motor control centers supplied by the 480 V shutdown boards The AC standby power system is divided into two redundant load groups (power trains).
The 6.9 kV shutdown boards are arranged electrically into two power trains with two boards associated with each train and each unit. The boards comprising train A are located in the SQN Unit 1 side and those of train B are located in the SQN Unit 2 side.
The train A boards are separated from the train B boards by a reinforced concrete block wall, which is a qualified fire barrier, extended to the ceiling. When the preferred (offsite) power system is not available, each shutdown board is energized from a separate standby DG.
CNL-16-001                                     E5 of 20
 
ENCLOSURE A loss of voltage on the 6.9 kV shutdown board starts the associated DG and initiates logic that trips the supply feeder breakers, all 6.9 kV loads (except the 480 V shutdown board transformers), and the major 480 V loads. The bypass breaker for the 480 V shutdown boards current-limiting inductive reactor is also closed as part of this logic.
When the DG has reached rated speed and voltage, the generator is automatically connected to the 6.9 kV shutdown board. This return of voltage to the 6.9 kV shutdown board initiates logic that connects the required loads in sequence. The standby (onsite) power system's automatic sequencing logic is designed to automatically connect the required loads in proper sequence should the logic receive an accident signal prior to, concurrent with, or following a loss of all nuclear unit and preferred (offsite) power.
As noted in UFSAR Section 8.3.1.1, there are two loading sequences:
One, which is applied in the absence of a safety injection signal (SIS), the non-accident condition, and the other accident condition, applied when an SIS (and containment spray actuation signal) is received coincident with a sustained loss of voltage on the 6.9 kV shutdown board.
A loss of offsite power coincident with an SIS is the design basis event; however, as noted in UFSAR Section 8.3.1.1, an SIS received during the course of a non-accident shutdown loading sequence would cause the actions described below.
: 1. Loads already sequentially connected that are not required for an accident will be disconnected (except fire pumps powered by the DG).
: 2. Loads already sequentially connected that are required for an accident will remain connected.
: 3. Loads pending sequential loading that are not required for an accident will not be connected.
: 3. Loads pending sequential loading that are not required for an accident will not be connected.
: 4. Loads awaiting sequential loading that are required for an accident will have their sequential timers reset to time zero from which they will then be sequentially loaded.An SIS received in the absence of a sustained loss of voltage on a 6.9 kV shutdown board would start the DGs , but would not connect them to the shutdown boards.
: 4. Loads awaiting sequential loading that are required for an accident will have their sequential timers reset to time zero from which they will then be sequentially loaded.
Each DG consists of two 16
An SIS received in the absence of a sustained loss of voltage on a 6.9 kV shutdown board would start the DGs, but would not connect them to the shutdown boards.
-cylinder engines directly connected to a 6.9 kV generator. The continuous rating of each DG is 4400 kilowatt (kW) at 0.8 power factor, 6.9 kV , 3-phase, and 60 Hz. Each DG also has an additional rating of 4840 kW for 2 hours out of 24 hours. Ratings for the DGs satisfy the requirements of Regulatory Guide 1.9 as clarified in Section 4.1. The continuous service rating of each DG is 4400 kW with 10% overload permissible for up to 2 hours in any 24 hour period. The normal operating speed of the DGs is 900 rpm. The DGs use a tandem arrangement; that is, each DG consists of two diesel engines with a generator between them connected together to form a common shaft. The DGs are physically separated, electrically isolated from each other, and protected from the probable maximum flood.
Each DG consists of two 16-cylinder engines directly connected to a 6.9 kV generator.
The continuous rating of each DG is 4400 kilowatt (kW) at 0.8 power factor, 6.9 kV, 3-phase, and 60 Hz. Each DG also has an additional rating of 4840 kW for 2 hours out of 24 hours.
Ratings for the DGs satisfy the requirements of Regulatory Guide 1.9 as clarified in Section 4.1. The continuous service rating of each DG is 4400 kW with 10% overload permissible for up to 2 hours in any 24 hour period.
The normal operating speed of the DGs is 900 rpm. The DGs use a tandem arrangement; that is, each DG consists of two diesel engines with a generator between them connected together to form a common shaft. The DGs are physically separated, electrically isolated from each other, and protected from the probable maximum flood.
CNL-16-001                                  E6 of 20


ENCLOSURE   CNL-16-001 E7 of 20  The DGs are equipped with Woodward governors and consist of:
ENCLOSURE The DGs are equipped with Woodward governors and consist of:
an E GB-13P actuator on each engine a 2301A computer (reverse biased) a magnetic speed pickup The Woodward EGB-13P actuator used with the 2301A computer is a proportional governor that moves the fuel rack in inverse proportion to the voltage signal from the computer. There is a governor actuator on each DG engine and they are electrically connected in series so that the loss of signal to one actuator would also result in the loss of signal to the other actuator. Based upon the input from the magnetic speed pickup, the electronic governor sends electric signals to the actuators on the two DG engines. This signal goes to the coils of each actuator that are connected in series so that each coil receives the same electric signal. The terminal shaft of each actuator will move the same amount for each change in signal, thus the fuel control shaft movement on each DG engine will be identical.
* an EGB-13P actuator on each engine
The steady state speed control will be within 0.25 percent of rated speed. The governor design includes circuits to provide high- and low-limit adjustments. These limits set the maximum and minimum speed that can be set by varying the speed
* a 2301A computer (reverse biased)
-setting milliamp or voltage reference. The low limit can be set as high as rated speed, if desired, eliminating the ability of the process or controller speed setting to reduce speed. The SQN Units 1 and 2 DG electrical governor is set within a speed band that is equivalent to a DG frequency of 59.95 Hz +/- 0.05 Hz. The SQN Units 1 and 2 DG voltage and frequency regulators were evaluated to ensure they were capable of meeting the TS and associated SRs. The measured values for both voltage and frequency have not exhibit ed drift and have been consistently within the respective setting band.
* a magnetic speed pickup The Woodward EGB-13P actuator used with the 2301A computer is a proportional governor that moves the fuel rack in inverse proportion to the voltage signal from the computer. There is a governor actuator on each DG engine and they are electrically connected in series so that the loss of signal to one actuator would also result in the loss of signal to the other actuator. Based upon the input from the magnetic speed pickup, the electronic governor sends electric signals to the actuators on the two DG engines.
This signal goes to the coils of each actuator that are connected in series so that each coil receives the same electric signal. The terminal shaft of each actuator will move the same amount for each change in signal, thus the fuel control shaft movement on each DG engine will be identical.
The steady state speed control will be within 0.25 percent of rated speed. The governor design includes circuits to provide high- and low-limit adjustments. These limits set the maximum and minimum speed that can be set by varying the speed-setting milliamp or voltage reference. The low limit can be set as high as rated speed, if desired, eliminating the ability of the process or controller speed setting to reduce speed. The SQN Units 1 and 2 DG electrical governor is set within a speed band that is equivalent to a DG frequency of 59.95 Hz +/- 0.05 Hz.
The SQN Units 1 and 2 DG voltage and frequency regulators were evaluated to ensure they were capable of meeting the TS and associated SRs. The measured values for both voltage and frequency have not exhibited drift and have been consistently within the respective setting band.
The SQN Units 1 and 2 DG voltage regulators and speed regulators are independent devices that are not expected to exhibit drift. This has been demonstrated by the past history of diesel surveillances in which the diesel is operated in isochronous mode. If the two variables drift in different directions (e.g., frequency lower and voltage higher), the combined effect on pump speed would be less than an individual drift.
The SQN Units 1 and 2 DG voltage regulators and speed regulators are independent devices that are not expected to exhibit drift. This has been demonstrated by the past history of diesel surveillances in which the diesel is operated in isochronous mode. If the two variables drift in different directions (e.g., frequency lower and voltage higher), the combined effect on pump speed would be less than an individual drift.
Based on this independence and stability, the composite impact of frequency and voltage were evaluated independently for the Technical Specification band. The frequency range was analyzed over the full range (i.e., 59.8 Hz to 60.2 Hz) within the voltage setting range (i.e., 6925 V to 7000 V). Likewise, the voltage (i.e., 6800 V to
Based on this independence and stability, the composite impact of frequency and voltage were evaluated independently for the Technical Specification band. The frequency range was analyzed over the full range (i.e., 59.8 Hz to 60.2 Hz) within the voltage setting range (i.e., 6925 V to 7000 V). Likewise, the voltage (i.e., 6800 V to 7260 V) was analyzed over the full range within the frequency range of 59.8 Hz to 60.2 Hz.
Test equipment verifies that the governor controls the DG frequency within the steady-state operational band of  59.8 Hz to  60.2 Hz.
The DGs, as clarified in Section 4.1, satisfy the requirements of Regulatory Guide (RG) 1.9, Revision 0 (Reference 3) and RG 1.9, Revision 1 (Reference 5).
CNL-16-001                                    E7 of 20


7260 V) was analyzed over the full range within the frequency range of 59.8 Hz to 60.2 Hz.
ENCLOSURE 3.2     Evaluation 3.2.1    Introduction Calculations were conducted to determine the effects of the DG frequency variation between 59.8 Hz and 60.2 Hz on plant equipment fed by the DGs following a loss of offsite power (LOOP) or a loss of coolant accident (LOCA) coincident with a LOOP.
Test equipment verifies that the governor controls the DG frequency within the steady
The changes in the DG frequency have the direct effect of changing motor speeds for the motors fed from the generators following a LOOP or a LOOP/LOCA. The changes in motor speeds are addressed in Section 3.2.2 and affect the following components:
-state operational band of 9.8 Hz to 0.2 Hz. The DGs, as clarified in Section 4.1, satisfy the requirements of Regulatory Guide (RG) 1.9, Revision 0 (Reference 3) and RG 1.9, Revision 1 (Reference 5).
* Pumps and Fans (Section 3.2.3)
ENCLOSURE   CNL-16-001 E8 of 20  Calculations were conducted to determine the effects of the DG frequency variation between 59.8 Hz and 60.2 Hz on plant equipment fed by the DGs following a loss of offsite power (LOOP) or a loss of coolant accident (LOCA) coincident with a LOOP. The changes in the DG frequency have the direct effect of changing motor speeds for the motors fed from the generators following a LOOP or a LOOP/LOCA. The changes in motor speeds are addressed in Section 3.2.2 and affect the following components:   Pump s and Fans (Section 3.2.3)   Air compressor s and chiller s (Section 3.2.4)   Motor operated valves (MOVs)
* Air compressors and chillers (Section 3.2.4)
(Section 3.2.5)   Electrical Equipment (Section 3.2.6) The changes in these parameters were evaluated to demonstrate that the subject equipment would continue to meet their safety related functions within the analyzed bounds documented in design documents. In addition, the increased horsepower associated with increased frequency was evaluated to ensure that the horsepower increases do not result in exceeding the sustained load ratings for the DGs and the decreased flowrate associated with the revised frequency range was evaluated to ensure pump parameters are adequate. Battery chargers and power transformers do not have motors, but frequency changes were examined to determine if the chargers and transformers would provide acceptable output parameters to continue to meet the specifications and requirements of the downstream components.
* Motor operated valves (MOVs) (Section 3.2.5)
The results of these calculations are provided below. Motor speed change, as a function of torque (Reference 6), is: S = (/N1)(SsynS) where, S = speed change Ssyn = motor synch speed S = motor speed
* Electrical Equipment (Section 3.2.6)
  = original torque N = the new torque The motor speed is directly affected by the frequency. T he affected component s , listed in Section 3.2.1, are either designed for 6600 V operation with the supply boards rated at 6900 V, or designed for 460 V operation with the supply boards rated ENCLOSURE    CNL-16-001 E9 of 20   at 480 V. Therefore, during normal operation, the motors see a voltage higher than their nominal rating. Thus, for the lower voltage limit of 6800 V (473 V on the low voltage side), the motors still have their minimum voltage and produce their design torque. Therefore, a low voltage condition is a non
The changes in these parameters were evaluated to demonstrate that the subject equipment would continue to meet their safety related functions within the analyzed bounds documented in design documents. In addition, the increased horsepower associated with increased frequency was evaluated to ensure that the horsepower increases do not result in exceeding the sustained load ratings for the DGs and the decreased flowrate associated with the revised frequency range was evaluated to ensure pump parameters are adequate. Battery chargers and power transformers do not have motors, but frequency changes were examined to determine if the chargers and transformers would provide acceptable output parameters to continue to meet the specifications and requirements of the downstream components.
-bounding condition and was not further evaluated.
The results of these calculations are provided below.
For the high voltage case, the motors could have a voltage of 7260 V (505 V on the low voltage side) or 10 percent above the motor design nominal rating , neglecting any voltage drop from the DG to the motor.
3.2.2    Comparison of Voltage and Frequency Impact Motor speed change, as a function of torque (Reference 6), is:
S = (/N1)(SsynS) where, S = speed change Ssyn = motor synch speed S = motor speed
          = original torque N = the new torque The motor speed is directly affected by the frequency. The affected components, listed in Section 3.2.1, are either designed for 6600 V operation with the supply boards rated at 6900 V, or designed for 460 V operation with the supply boards rated CNL-16-001                                   E8 of 20
 
ENCLOSURE at 480 V. Therefore, during normal operation, the motors see a voltage higher than their nominal rating. Thus, for the lower voltage limit of 6800 V (473 V on the low voltage side), the motors still have their minimum voltage and produce their design torque. Therefore, a low voltage condition is a non-bounding condition and was not further evaluated. For the high voltage case, the motors could have a voltage of 7260 V (505 V on the low voltage side) or 10 percent above the motor design nominal rating, neglecting any voltage drop from the DG to the motor.
Because the torque developed by a motor is directly proportional to the square of the terminal voltage, the above equation is rewritten in terms of voltage, as follows:
Because the torque developed by a motor is directly proportional to the square of the terminal voltage, the above equation is rewritten in terms of voltage, as follows:
 
S = [(V/VN)21]*(SsynS) where, S = speed change (SsynS) = motor slip, < 2 percent (the value of 2 percent is based on a review of vendor manuals which demonstrates that the motors have < 2 percent slip)
S = [(V/V N)21]*(SsynS) where, S = speed change (SsynS) = motor slip, < 2 percent (th e value of 2 percent is based on a review of vendor manuals which demonstrates that the motors have < 2 percent slip)
V = Nominal voltage, 6600 V VN = New voltage, 7260 V S = [(6600/7260)21]*(2 percent)
V = Nominal voltage, 6600 V V N = New voltage, 7260 V S = [(6600/7260) 2]*(2 percent)
S = -0.35 percent Thus, with a motor slip of less than 2 percent, the motor speed impact is less than 0.35 percent due to the voltage increase to 7260 V from design voltage of 6600 V.
S = -0.35 percent Thus, with a motor slip of less than 2 percent, the motor speed impact is less than 0.35 percent due to the voltage increase to 7260 V from design voltage of 6600 V. The frequency shift could result in a + 0.35 percent motor speed and the voltage could result in +0.35 percent motor speed change.
The frequency shift could result in a + 0.35 percent motor speed and the voltage could result in +0.35 percent motor speed change. Therefore, a speed impact of
Therefore, a speed impact of
        + 0.35 percent was used as the DG frequency impact for analyzing the effect caused either by frequency or voltage variation on the affected components in the following sections.
+ 0.35 percent was used as the DG frequency impact for analyzing the effect caused either by frequency or voltage variation on the affected components in the following sections.
3.2.3    Effect on Pumps 3.2.3.1  Pump Net Positive Suction Head (NPSH)
The change in the DG frequency was evaluated for the effect on the NPSH available to the following emergency core cooling system (ECCS) pumps. These pumps are fed from the DGs; therefore, they could be affected by the variation in frequency of 59.8 Hz to 60.2 Hz:
The change in the DG frequency was evaluated for the effect on the NPSH available to the following emergency core cooling system (ECCS) pumps. These pumps are fed from the DGs; therefore, they could be affected by the variation in frequency of 59.8 Hz to 60.2 Hz:
Containment spray (CS)
* Containment spray (CS)
Safety injection (SI)
* Safety injection (SI)
Residual heat removal (RHR)
* Residual heat removal (RHR)
Centrifugal charging (CC)
* Centrifugal charging (CC)
An evaluation was performed to determine if the NPSH available (NPSHA) exceeds the NPSH required (NPSHR) for the RHR and the CS pumps while taking suction from the containment sump (recirculation mode). The evaluation also determined ENCLOSURE    CNL-16-001 E 10 of 20   the NPSH Margin for the CS, SI, RHR, and CC pumps during injection mode operation with suction taken from the refueling water storage tank (RWST). Only the injection mode is presented, as the injection mode has less NPSH margin than the recirculation mode.
An evaluation was performed to determine if the NPSH available (NPSHA) exceeds the NPSH required (NPSHR) for the RHR and the CS pumps while taking suction from the containment sump (recirculation mode). The evaluation also determined CNL-16-001                                 E9 of 20
DG frequency affects both the head and flow values based on the pump affinity laws as follows:
 
Q 2 = (N 2 N 1)*Q1            where, Q2 = Changed pump flow due to DG frequency variation Q1 = Nominal pump flow N2  = Changed pump speed due to DG frequency variation N 1  = Nominal pump speed
 
For the 59.8 Hz frequency, Q 2 = (59.8/60.0)*Q 1 = 0.997*Q1  For the 60.2 Hz frequency, Q 2 = (60.2/60.0)*Q 1 = 1.003*Q1  Therefore, a 0.2Hz change in DG frequency will change pump flow by + 0.33%.      The NPSHR for pumps increases as the speed and flowrate increase. The NPSHR is also affected by the increase in DG frequency as follows
:  NPSHR 2 = (N 22)4/3*NPSHR 1                  (N 11)4/3    Table 2 presents examples of NPSHR changes resulting from the DG frequency changes for the various pumps.
The results in Table 3 demonstrate the actual flow rates, NPSHA, NPSHR, and the NPSH Margin for the various pumps. The NPSHR values were obtained from the pump manufacturer's NPSH curves at the flow values that are listed in Table 3. The DG increased frequency effects are included in these values. The results demonstrate that there is adequate positive margin for the pumps with the DG operating at the proposed revised frequencies.


ENCLOSURE   CNL-16-001 E 11 of 20  NPSHR (ft) current12.522 37.516NPSHR (ft) at 60.2 Hz12.622.1 37.816.1 Increased Pump Flow (sgpm)5100 5100 450 450 500 500 4200 4200 Pump Suction P (psig) 3.8 -2.5 6.7 6.8 1.9 1.6 -1.6 -3.9 Pump Suction P (psia) 18.2 11.9 21.1 21.2 16.3 16.0 12.8 10.5 Vapor P at 105&deg;F (psia) 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 NPSHA (psi) 17.1 10.8 20 20.1 15.2 14.9 11.7 9.4 NPSHA (ft) 39.7 25.1 46.5 46.7 35.3 34.6 27.2 21.8 NPSHR (ft) 12.1 12.1 18 18 19 19 15 15 NPSH margin (ft) 27.6 13 28.5 28.7 16.3 15.6 12.2 6.8    The DG frequency variation of 59.8 Hz to 60.2 Hz has a negligible effect on plant operations for the above affected pumps based on the revised flow rates in Section 3.2.3.1. The flow change resulting from the DG frequency variation is limited to + 0.3 5%. The pump test acceptance criteria upper limit will be adjusted downward, and the lower limit will be adjusted upward in order to encompass the potential flow variation. The ASME OM Code inservice pump testing acceptance criteria provide assurance that the design basis is met.
ENCLOSURE the NPSH Margin for the CS, SI, RHR, and CC pumps during injection mode operation with suction taken from the refueling water storage tank (RWST). Only the injection mode is presented, as the injection mode has less NPSH margin than the recirculation mode.
DG frequencies above/below 60 Hz directly increase/reduce motor speeds for fans. Fan speed is directly proportional to fan flow. Therefore, increased/reduced motor speed will result in increased/reduced flows.
3.2.3.1.1 Pump Flow Rates DG frequency affects both the head and flow values based on the pump affinity laws as follows:
For the 60.2 Hz DG frequency, fan flows are impacted as follows:
Q2 = (N2IN1)*Q1 where, Q2 = Changed pump flow due to DG frequency variation Q1 = Nominal pump flow N2 = Changed pump speed due to DG frequency variation N1 = Nominal pump speed For the 59.8 Hz frequency, Q2 = (59.8/60.0)*Q1 = 0.997*Q1 For the 60.2 Hz frequency, Q2 = (60.2/60.0)*Q1 = 1.003*Q1 Therefore, a 0.2Hz change in DG frequency will change pump flow by + 0.33%.
3.2.3.1.2 NPSH The NPSHR for pumps increases as the speed and flowrate increase. The NPSHR is also affected by the increase in DG frequency as follows:
NPSHR2 = (N2Q2)4/3*NPSHR1 (N1Q1)4/3 Table 2 presents examples of NPSHR changes resulting from the DG frequency changes for the various pumps.
The results in Table 3 demonstrate the actual flow rates, NPSHA, NPSHR, and the NPSH Margin for the various pumps. The NPSHR values were obtained from the pump manufacturers NPSH curves at the flow values that are listed in Table 3. The DG increased frequency effects are included in these values. The results demonstrate that there is adequate positive margin for the pumps with the DG operating at the proposed revised frequencies.
CNL-16-001                                  E10 of 20


ENCLOSURE    CNL-16-001 E 12 of 20   Q 2 = (60.2/60.0)*Q 1 = 1.0033*Q1 and for the 59.8 Hz DG frequency, fan flows are impacted as follows; Q 2 = (59.8/60.0)*Q1 = 0.9967*Q1 where: Q 2 = Changed fan flow due to DG frequency variation Q 1 = Nominal fan flow From the above equations, fan flow could vary from nominal to about +0.3 3%. From the G-Spec (Reference 7), total airflow of a system can vary by
ENCLOSURE Table 2 Example NPSHR Changes System                    CS              CC              SI            RHR NPSHR (ft) current            12.5              22            37.5            16 NPSHR (ft) at                  12.6            22.1          37.8            16.1 60.2 Hz Table 3 NPSH Margin While Operating in RWST Injection Mode with Revised DG Frequency System                    CS              CC            SI            RHR Pump Number            A-A      B-B   A-A B-B        A-A      B-B    A-A      B-B Increased Pump            5100      5100    450    450    500    500    4200      4200 Flow (sgpm)
+10% at the system fan. Thus, fan flows are within allowed tolerances due to sustained DG frequency variations
Pump Suction P              3.8      -2.5    6.7      6.8   1.9      1.6    -1.6    -3.9 (psig)
. Horsepower requirements for a pump motor and fan increase by the cube of the speed change. Therefore, increased motor speed will result in increased horsepower demands on the diesels that feed the subject loads. The potential increase in load on the DGs due to operating frequency and voltage was evaluated to 60.2 Hz and 7260 V. The highest steady state loading was used which envelopes the other steady state loading scenarios.
Pump Suction P            18.2     11.9  21.1    21.2 16.3    16.0   12.8    10.5 (psia)
Motor slip is defined as the difference between actual speed and synchronous speed
Vapor P at 105&deg;F            1.1      1.1    1.1      1.1  1.1      1.1    1.1       1.1 (psia)
 
NPSHA (psi)                17.1      10.8     20    20.1  15.2     14.9    11.7      9.4 NPSHA (ft)                39.7      25.1  46.5    46.7  35.3    34.6    27.2    21.8 NPSHR (ft)                12.1      12.1    18      18    19      19      15      15 NPSH margin (ft)           27.6      13    28.5    28.7  16.3    15.6    12.2      6.8 3.2.3.2     Pump Test Points The DG frequency variation of 59.8 Hz to 60.2 Hz has a negligible effect on plant operations for the above affected pumps based on the revised flow rates in Section 3.2.3.1. The flow change resulting from the DG frequency variation is limited to + 0.35%. The pump test acceptance criteria upper limit will be adjusted downward, and the lower limit will be adjusted upward in order to encompass the potential flow variation. The ASME OM Code inservice pump testing acceptance criteria provide assurance that the design basis is met.
an induction machine operates at as a percentage of the synchronous speed. A motor slip of about one percent increase in speed was calculated based on the increased DG voltage.
3.2.3.3    Effect on Fans DG frequencies above/below 60 Hz directly increase/reduce motor speeds for fans.
Fan speed is directly proportional to fan flow. Therefore, increased/reduced motor speed will result in increased/reduced flows. For the 60.2 Hz DG frequency, fan flows are impacted as follows:
CNL-16-001                                    E11 of 20


ENCLOSURE Q2 = (60.2/60.0)*Q1 = 1.0033*Q1 and for the 59.8 Hz DG frequency, fan flows are impacted as follows; Q2 = (59.8/60.0)*Q1 = 0.9967*Q1 where:
Q2 = Changed fan flow due to DG frequency variation Q1 = Nominal fan flow From the above equations, fan flow could vary from nominal to about +0.33%. From the G-Spec (Reference 7), total airflow of a system can vary by +10% at the system fan. Thus, fan flows are within allowed tolerances due to sustained DG frequency variations.
3.2.3.4  Effect on Horsepower Requirements Horsepower requirements for a pump motor and fan increase by the cube of the speed change. Therefore, increased motor speed will result in increased horsepower demands on the diesels that feed the subject loads. The potential increase in load on the DGs due to operating frequency and voltage was evaluated to 60.2 Hz and 7260 V. The highest steady state loading was used which envelopes the other steady state loading scenarios.
Motor slip is defined as the difference between actual speed and synchronous speed an induction machine operates at as a percentage of the synchronous speed. A motor slip of about one percent increase in speed was calculated based on the increased DG voltage.
Motor speed varies directly with the system frequency as shown below:
Motor speed varies directly with the system frequency as shown below:
1/2 = 1/ 2    Thus, the speed impact of the frequency variation is (60 + 0.2)/60 or + 0.33%. Therefore, the total impact of the voltage and frequency shift would be the sum of 1% + 0.33% which equals a 1.33% increase in motor speed.
1/2 = f1/f2 Thus, the speed impact of the frequency variation is (60 + 0.2)/60 or + 0.33%.
Therefore, the total impact of the voltage and frequency shift would be the sum of 1% + 0.33% which equals a 1.33% increase in motor speed.
As noted above, motor horsepower varies directly with the cube of the motor speed:
As noted above, motor horsepower varies directly with the cube of the motor speed:
LoadNew = Loadold Speed 3  LoadNew = LoadOld
LoadNew = Loadold *Speed3 LoadNew = LoadOld
* 1.0133 3  = LoadOld *1.040 Therefore, DG load would be increased by 4% if both the voltage and frequency were at their upper limits of 7260 V and 60.2 Hz
* 1.01333 = LoadOld *1.040 Therefore, DG load would be increased by 4% if both the voltage and frequency were at their upper limits of 7260 V and 60.2 Hz. Because the DG fuel oil consumption is analyzed for a fully loaded diesel, the voltage and frequency variation do not adversely affect the fuel oil analysis.
. Because the DG fuel oil consumption is analyzed for a fully loaded diesel, the voltage and frequency variation do not adversely affect the fuel oil analysis.
CNL-16-001                                E12 of 20


ENCLOSURE    CNL-16-001 E 13 of 20    Air compressors and chillers are intermittently operated equipment designed to maintain an asset or volume between selected setpoints. Air compressors cycle on to charge a system to a high pressure setpoint, and then cycle off until the header pressure drops below the specified setpoint. Chillers cycle on and off to maintain a refrigerant fluid temperature between a specified range of temperatures. Because both air compressors and chillers work intermittently to maintain a fluid media in a range between two setpoints, the approximate  
ENCLOSURE 3.2.4   Effect on Air Compressors and Chillers Air compressors and chillers are intermittently operated equipment designed to maintain an asset or volume between selected setpoints. Air compressors cycle on to charge a system to a high pressure setpoint, and then cycle off until the header pressure drops below the specified setpoint. Chillers cycle on and off to maintain a refrigerant fluid temperature between a specified range of temperatures. Because both air compressors and chillers work intermittently to maintain a fluid media in a range between two setpoints, the approximate +0.33% (+0.2 Hz) variation in DG frequency has a negligible effect on this type of equipment.
+0.3 3% (+0.2 Hz) variation in DG frequency has a negligible effect on this type of equipment.
3.2.5    Effect on MOVs The affected MOVs were evaluated for frequency and voltage related to DG loading.
 
The affected MOVs were evaluated for frequency and voltage related to DG loading.
Motor torque and stroke time are two important parameters associated with MOV performance. The DG frequency affects the motor torque (Section 3.2.2) and speed.
Motor torque and stroke time are two important parameters associated with MOV performance. The DG frequency affects the motor torque (Section 3.2.2) and speed.
Valve stroke time is inversely proportional to motor speed. Therefore, faster/slower motor speed would result in shorter/longer valve stroke times. For the 60.2 Hz frequency, valve stroke times vary as follows:
Valve stroke time is inversely proportional to motor speed. Therefore, faster/slower motor speed would result in shorter/longer valve stroke times. For the 60.2 Hz frequency, valve stroke times vary as follows:
T 2 = (60.2/60
T2 = (60.2/60.0)*T1 = 1.0033*T1                                          Equation (1) and for the 59.8 to 60.0 Hz DG frequency range, valve stroke times are affected as follows; T2 = (59.8/60.0)*T1 = 0.9967*T1                                          Equation (2) where:
.0)*T 1 = 1.00 33*T 1     Equation (1)
T2 = Changed stroke time due to DG frequency variation T1 = Nominal stroke time From equations (1) and (2), valve stroke times vary from nominal to approximately
        +0.33%. For example, a valve that strokes in 30 seconds has the potential variation in stroke time of approximately +0.1 seconds. This potential variation is small in comparison to the valve stroke times documented in the inservice testing program and is essentially the same as the recorded resolution of the stop watches used for valve stroke time testing (i.e., 0.1 seconds). The majority of the active safety related MOVs stroke in 10 seconds or less; therefore, the variance in stroke time is
        + 0.03 seconds. For a 10-second valve, this is below the detectible threshold of the normal timing method. The longest of the safety related valve stroke times is up to 120 seconds for the valves involved in the automatic containment sump swap over.
The time variation is about + 0.4 seconds for these valves.
The MOV stroke time acceptance criteria for the ASME OM Code testing are adjusted to include the potential low frequency power. Accordingly, the design basis requirements for valve stroke time will be met. The minimum allowable DG voltage provides a voltage that is greater than the voltage used for the Generic Letter 89-10 analysis.
CNL-16-001                                  E13 of 20


and for the 59.8 to 60.0 Hz DG frequency range, valve stroke times are affected as follows; T 2 = (59.8/60.0)*T 1 = 0.99 67*T 1      Equation (2) where:  T 2 = Changed stroke time due to DG frequency variation T 1 = Nominal stroke time From equations (1) and (2), valve stroke times vary from nominal to approximately
ENCLOSURE Furthermore, based on the analyses in Section 3.2.2, the impact to torque is acceptable. In addition, there would not be a concern for water hammer due to the small change in stroke time. Therefore, there are no concerns with MOV operation due to the variation in DG frequency and voltage.
+0.3 3%. For example, a valve that strokes in 30 seconds has the potential variation in stroke time of approximately
3.2.6    Effect on Electrical Equipment Most static loads are insensitive to changes in frequency and have a directly proportional change in current with terminal voltage, which is the opposite of the effects of voltage variation on induction motors. Only electronically controlled equipment, such as battery chargers, inverters and uninterruptible power supplies may be of concern at off nominal line frequency. The maximum allowable board voltage is 7260 V and the degraded voltage relay safety limit dropout setting is 6400 V. The variation in voltage from the DG of 6800 to 7260 V is much less than the range expected from the offsite source. Therefore, the variation in DG output voltage is bounded by voltage variations when off site power supplies the AC auxiliary power system.
+0.1 seconds. This potential variation is small in comparison to the valve stroke times documented in the inservice testing program and is essentially the same as the recorded resolution of the stop watches used for valve stroke time testing (i.e., 0.1 seconds). The majority of the active safety related MOVs stroke in 1 0 seconds or less; therefore, the variance in stroke time is + 0.03 seconds. For a 10-second valve, this is below the detectible threshold of the normal timing method. The longest of the safety related valve stroke times is up to 120 seconds for the valves involved in the automatic containment sump swap over. The time variation is about + 0.4 seconds for these valves.  
3.2.6.1  Battery Chargers The battery charger regulation is maintained at +/-1% from no-load to full load with simultaneous changes in AC line voltage of +10% / -15% and changes in AC line frequency of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the battery chargers.
3.2.6.2  Hydrogen Igniters The hydrogen mitigation system (i.e., H2 igniters) does not use frequency sensitive components with the exception of the regulating transformer. The output is regulated to +/-1% from no-load to full load with AC line voltage changes of +/-10% and changes in AC frequency changes of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the hydrogen mitigation system.
3.2.6.3  Instrumentation 120 V AC instrumentation circuits are designed with a +/-1% variation in frequency.
The variation in DG frequency is within this range.
3.3      Conclusion The results of these calculations determined that the proposed change in the DG frequency does not adversely affect the equipment powered by the DGs and their associated components described above. The calculations are available for NRC review. The DG output voltage and frequency range of 6800 to 7260 V and 59.8 to 60.2 Hz, respectively, will not affect the miscellaneous electrical equipment required to mitigate design basis events.
CNL-16-001                                  E14 of 20


The MOV stroke time acceptance criteria for the ASME OM Code testing are adjusted to include the potential low frequency power. Accordingly, the design basis requirements for valve stroke time will be met.
ENCLOSURE
The minimum allowable DG voltage provides a voltage that is greater than the voltage used for the Generic Letter 89-10 analysis.
ENCLOSURE   CNL-16-001 E 14 of 20    Furthermore, based on the analyses in Section 3.2.2, the impact to torque is acceptable. In addition, there would not be a concern for water hammer due to the small change in stroke time.
Therefore, there are no concerns with MOV operation due to the variation in DG frequency and voltage.
Most static loads are insensitive to changes in frequency and have a directly proportional change in current with terminal voltage, which is the opposite of the effects of voltage variation on induction motors. Only electronically controlled equipment, such as battery chargers, inverters and uninterruptible power supplies may be of concern at off nominal line frequency. The maximum allowable board voltage is 7260 V and the degraded voltage relay safety limit dropout setting is 6400 V. The variation in voltage from the DG of 6800 to 7260 V is much less than the range expected from the offsite source. Therefore, the variation in DG output voltage is bounded by voltage variations when off site power supplies the AC auxiliary power system.
The battery charger regulation is maintained at +/-1% from no
-load to full load with simultaneous changes in AC line voltage of +10% /
-15% and changes in AC line frequency of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the battery chargers. The hydrogen mitigation system (i.e., H 2 igniters) does not use frequency sensitive components with the exception of the regulating transformer. The output is regulated to +/-1% from no
-load to full load with AC line voltage changes of +/-10% and changes in AC frequency changes of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the hydrogen mitigation system.


120 V AC instrumentation circuits are designed with a +/-1% variation in frequency. The variation in DG frequency is within this range.
==4.0  REGULATORY EVALUATION==


The results of these calculations determined that the proposed change in the DG frequency does not adversely affect the equipment powered by the DGs and their associated components described above. The calculations are available for NRC review. The DG output voltage and frequency range of 6800 to 7260 V and 59.8 to 60.2 Hz, respectively, will not affect the miscellaneous electrical equipment required to mitigate design basis events. 
4.1  Applicable Regulatory Requirements and Criteria The onsite standby ac power systems at SQN Units 1 and 2 are designed to comply with the following applicable regulations and requirements.
* Title 10 of the Code of Federal Regulations (10 CFR) Part 50 (10 CFR 50),
Appendix A, General Design Criterion (GDC) 17, "Electric power systems," specifies that an onsite electric power system shall be provided to permit functioning of structures, systems, and components important to safety.
* 10 CFR 50, Appendix A, GDC 18, "Inspection and testing of electric power systems,"
specifies that electric power systems important to safety shall be designed to permit appropriate periodic inspection and testing of important areas and features.
* Regulatory Guide 1.6, Revision 0 (Reference 8), "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems," describes an acceptable degree of independence between redundant standby (onsite) power sources and between their distribution systems.
* Regulatory Guide 1.9, Revision 0 (Reference 3). As noted in SQN UFSAR Section 8.3.1.2.1, SQN Units 1 and 2 comply with Regulatory Guide 1.9, Revision 0 except that voltage and frequency recovery requirements are taken from Regulatory Guide 1.9, Revision 1. As further noted in SQN UFSAR Section 8.3.1.2.1, an exception is taken for frequency immediately following DG breaker closure. The DG breaker is designed to automatically close at about 94 percent of nominal frequency.
This exception was accepted by the NRC in NUREG-1232 Volume 2 (Reference 9).
* IEEE Standard 308-1971, "Criteria for Class 1E Power Systems for Nuclear Power Generating Stations," provides criteria for the determination of Class 1E power system design features and the requirements for their testing, surveillance, and documentation.
With the implementation of the proposed change, SQN Units 1 and 2 continues to meet the applicable regulations and requirements, subject to the previously approved exceptions.
4.2  Precedent The NRC has previously approved changes revising the TS SR acceptance criteria for steady state DG frequency.
: 1. Amendment Number 102 was issued for WBN Unit 1 in the Safety Evaluation dated September 17, 2015 (Reference 2). The Amendment made changes similar to those in this proposed license amendment request in that it revised the DG SR steady state frequency from  58.8 Hz and 61.2 Hz to 59.8 Hz and  60.1 Hz.
: 2. Amendment Numbers 227 and 105 were issued for Beaver Valley Power Station, Units 1 and 2, respectively, in the Safety Evaluation dated February 11, 2000 CNL-16-001                                  E15 of 20


ENCLOSURE   CNL-16-001 E 15 of 20  The onsite standby ac power systems at SQN Units 1 and 2 are designed to comply with the following applicable regulations and requirements. Title 10 of the Code of Federal Regulations (10 CFR) Part 50 (10 CFR 50), Appendix A, General Design Criterion (GDC) 17, "Electric power systems," specifies that an onsite electric power system shall be provided to permit functioning of structures, systems, and components important to safety.
ENCLOSURE (Reference 10). The Amendment corrected non-conservative TSs by clarifying the fuel oil storage volume requirements, increasing the load requirement for the single largest load rejection test, establishing criteria for maximum frequency that should not be exceeded following a load rejection, and revising the DG SR steady state frequency to  60.0 Hz and  60.6 Hz for Units 1 and 2 and 59.9 Hz and  60.3 Hz for Unit 2.
10 CFR 50, Appendix A, GDC 18, "Inspection and testing of electric power systems," specifies that electric power systems important to safety shall be designed to permit appropriate periodic inspection and testing of important areas and features.
: 3. Amendment Number 129 was issued for the Palo Verde Nuclear Generating Station, Units 1, 2, and 3, in the Safety Evaluation dated October 4, 2000 (Reference 11).
Regulatory Guide 1.6, Revision 0 (Reference 8), "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems," describes an acceptable degree of independence between redundant standby (onsite) power sources and between their distribution systems.
The Amendment corrected non-conservative TSs by revising the current steady-state DG voltage limits of  3740 V and  4580 V and steady state frequency limit of 59.7 Hz and  61.2 Hz to a steady state voltage of 4000 V and <4377.2 V, and steady state frequency of  59.7 Hz and  60.7 Hz for the affected SR, except that for SR 3.8.1.2, the lower frequency limit is  58.8 Hz instead of the  59.7 Hz.
Regulatory Guide 1.9, Revision 0 (Reference 3). As noted in SQN UFSAR Section 8.3.1.2.1, SQN Units 1 and 2 comply with Regulatory Guide 1.9, Revision 0 except that voltage and frequency recovery requirements are taken from Regulatory Guide 1.9, Revision 1. As further noted in SQN UFSAR Section 8.3.1.2.1, an exception is taken for frequency immediately following DG breaker closure. The DG breaker is designed to automatically close at about 94 percent of nominal frequency. This exception was accepted by the NRC in NUREG
: 4. Amendment Numbers 309 and 291 were issued for the Donald C. Cook Nuclear Plant, Units 1 and 2, respectively, in the Safety Evaluation dated April 30, 2009 (Reference 12). The Amendment corrected non-conservative TSs by reducing the maximum DG steady state frequency in the associated SRs from 61.2 Hz to 60.5 Hz.
-1232 Volume 2 (Reference 9). IEEE Standard 308
The Amendment also revised the minimum steady state voltage from 3740 V to 3910 V for certain TS SRs for consistency with the minimum steady state voltage specified in the acceptance criteria for other TS SRs, and reduced the criteria for maximum frequency that should not be exceeded following a load rejection.
-1971, "Criteria for Class 1E Power Systems for Nuclear Power Generating Stations," provides criteria for the determination of Class 1E power system design features and the requirements for their testing, surveillance, and documentation.
: 5. Amendment Number 236 was issued for Crystal River, Unit 3 in the Safety Evaluation dated December 10, 2009 (Reference 13). The Amendment corrected non-conservative TSs by revising the DG steady state voltage to 4077 V and 4243 V and DG steady state frequency to  59.4 Hz and 60.6 Hz.
: 6. Amendment 204 was issued for the Wolf Creek Generating Station in the Safety Evaluation dated April 11, 2013 (Reference 14). The Amendment corrected non-conservative TSs by revising minimum DG steady state voltage to 3950 V and DG steady state frequency to 59.4 Hz and 60.6 Hz. The Amendment also revised the DG loading requirements to reflect the results of updated calculations.
4.3  Significant Hazards Consideration The proposed change would modify the Sequoyah Nuclear Plant (SQN), Units 1 and 2, Technical Specification (TS) 3.8.1, "AC Sources - Operating," by revising the acceptance criteria for the diesel generator (DG) steady state frequency acceptance criteria specified in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. The frequency will be changed from  58.8 Hz and  61.2 Hz to 59.8 Hz and 60.2 Hz for SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18.
This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed.
CNL-16-001                                  E16 of 20


With the implementation of the proposed change, SQN Units 1 and 2 continues to meet the applicable regulations and requirements, subject to the previously approved exceptions.
ENCLOSURE TVA has evaluated whether or not a significant hazards consideration is involved with the proposed amendment(s) by focusing on the three standards set forth in 10 CFR 50.92, Issuance of amendment, as discussed below:
The NRC has previously approved changes revising the TS SR acceptance criteria for steady state DG frequency.
: 1.     Does the proposed amendment involve a significant increase in the probability or consequence of an accident previously evaluated?
: 1. Amendment Number 102 was issued for WBN Unit 1 in the Safety Evaluation dated September 17, 2015 (Reference 2). The Amendment made changes similar to those in this proposed license amendment request in that it revised the DG SR steady state frequency from 58.8 Hz and 61.2 Hz to  59.8 Hz and 60.1 Hz. 2. Amendment Numbers 227 and 105 were issued for Beaver Valley Power Station, Units 1 and 2, respectively, in the Safety Evaluation dated February 11, 2000 ENCLOSURE    CNL-16-001 E 16 of 20  (Reference 10). The Amendment corrected non
Response: No The DGs are required to be operable in the event of a design basis accident coincident with a loss of offsite power to mitigate the consequences of the accident. The DGs are not accident initiators and therefore these changes do not involve a significant increase in the probability of an accident previously evaluated.
-conservative TSs by clarifying the fuel oil storage volume requirements, increasing the load requirement for the single largest load rejection test, establishing criteria for maximum frequency that should not be exceeded following a load rejection, and revising the DG SR steady state frequency to  60.0 Hz and 0.6 Hz for Units 1 and 2 59.9  60.3 Hz for Unit 2.
: 3. Amendment Number 129 was issued for the Palo Verde Nuclear Generating Station, Units 1, 2, and 3, in the Safety Evaluation dated October 4, 2000 (Reference 11). The Amendment corrected non
-conservative TSs by revising the current steady
-state  3740 V  4580 V and steady state frequency limit of  59.7 Hz and 1.2 Hz to a steady s4000 V and <4377.2 V, and steady state frequency of 9.7 Hz and 0.7 Hz for the affected SR, except that for SR 3.8.1.2, the lower frequency limit is 8.8 Hz instead of the 9.7 Hz. 4. Amendment Numbers 309 and 291 were issued for the Donald C. Cook Nuclear Plant, Units 1 and 2, respectively, in the Safety Evaluation dated April 30, 2009 (Reference 12). The Amendment corrected non
-conservative TSs by reducing the maximum DG steady state frequency in the associated SRs from 61.2 Hz to 60.5 Hz. The Amendment also revised the minimum steady state voltage from 3740 V to  3910 V for certain TS SRs for consistency with the minimum steady state voltage specified in the acceptance criteria for other TS SRs, and reduced the criteria for maximum frequency that should not be exceeded following a load rejection
. 5. Amendment Number 236 was issued for Crystal River, Unit 3 in the Safety Evaluation dated December 10, 2009 (Reference 13). The Amendment corrected non-conservative TSs by V and  4243 V and DG steady state frequency to 9.4 Hz and 0.6 Hz. 6. Amendment 204 was issued for the Wolf Creek Generating Station in the Safety Evaluation dated April 11, 2013 (Reference 14). The Amendment corrected non-conservative TSs by revising minimum DG steady state voltage to 3950 V and DG steady state frequency to 9.4 Hz and 0.6 Hz. The Amendment also revised the DG loading requirements to reflect the results of updated calculations. The proposed change would modify the Sequoyah Nuclear Plant (SQN), Units 1 and 2, Technical Specification (TS) 3.8.
1 , "AC Sources - Operating," by revising the acceptance criteria for the diesel generator (DG) steady state frequency acceptance criteria specified in TS Surveillance Requirements (SR s) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.188.8 Hz and  61.2 Hz to 9.8 Hz and 0.2 Hz for SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed. 
 
ENCLOSURE   CNL-16-001 E 17 of 20  TVA has evaluated whether or not a significant hazards consideration is involved with the proposed amendment(s) by focusing on the three standards set forth in 10 CFR 50.92, "Issuance of amendment," as discussed below:
: 1. Does the proposed amendment involve a significant increase in the probability or consequence of an accident previously evaluated? Response: No The DGs are required to be operable in the event of a design basis accident coincident with a loss of offsite power to mitigate the consequences of the accident. The DGs are not accident initiators and therefore these changes do not involve a significant increase in the probability of an accident previously evaluated.
The accident analyses assume that at least the boards in one load group are provided with power either from the offsite circuits or the DGs. The change proposed in this license amendment request will continue to assure that the DGs have the capacity and capability to assume their maximum design basis accident loads. The proposed change does not significantly alter how the plant would mitigate an accident previously evaluated.
The accident analyses assume that at least the boards in one load group are provided with power either from the offsite circuits or the DGs. The change proposed in this license amendment request will continue to assure that the DGs have the capacity and capability to assume their maximum design basis accident loads. The proposed change does not significantly alter how the plant would mitigate an accident previously evaluated.
The proposed change does not adversely affect accident initiators or precursors nor alter the design assumptions, conditions, and configuration of the facility or the manner in which the plant is operated and maintained. The proposed change does not adversely affect the ability of structures, systems, and components (SSC) to perform their intended safety function to mitigate the consequences of an initiating event within the assumed acceptance limits. The proposed change does not affect the source term, containment isolation, or radiological release assumptions used in evaluating the radiological consequences of any accident previously evaluated.
The proposed change does not adversely affect accident initiators or precursors nor alter the design assumptions, conditions, and configuration of the facility or the manner in which the plant is operated and maintained. The proposed change does not adversely affect the ability of structures, systems, and components (SSC) to perform their intended safety function to mitigate the consequences of an initiating event within the assumed acceptance limits. The proposed change does not affect the source term, containment isolation, or radiological release assumptions used in evaluating the radiological consequences of any accident previously evaluated. Further, the proposed change does not increase the types and amounts of radioactive effluent that may be released offsite, nor significantly increase individual or cumulative occupational/public radiation exposure.
Further, the proposed change does not increase the types and amounts of radioactive effluent that may be released offsite, nor significantly increase individual or cumulative occupational/public radiation exposure.
Therefore, the proposed change does not involve a significant increase in the probability or consequences of an accident previously evaluated.
Therefore, the proposed change does not involve a significant increase in the probability or consequences of an accident previously evaluated.
2.Does the proposed amendment create the possibility of a new or different kind of accident from any accident previously evaluat ed? Response: No.
: 2.     Does the proposed amendment create the possibility of a new or different kind of accident from any accident previously evaluated?
The proposed change does not involve a change in the plant design, system operation, or the use of the DGs. The proposed change requires the DGs to meet SR acceptance criteria that envelope the actual demand requirements for the DGs during design basis conditions. These revised acceptance criteria continue to demonstrate the capability and capacity of the DGs to perform their required functions. There are no new failure modes or mechanisms created due to testing the DGs within the proposed acceptance criteria. Testing of the DGs at the proposed acceptance criteria does not involve any modification in the ENCLOSURE    CNL-16-001 E 18 of 20   operational limits or physical design of plant systems. There are no new accident precursors generated due to the proposed test loadings. Therefore, the proposed change does not create the possibility of a new or different kind of accident from any accident previously evaluated.
Response: No.
3.Does the proposed amendment involve a significant reduction in a margin of safety? Response: No. The proposed change will continue to demonstrate that the DGs meet the TS definition of operability, that is, the proposed acceptance criteria will continue to demonstrate that the DGs will perform their safety function. The proposed testing will also continue to demonstrate the capability and capacity of the DGs to supply their required loads for mitigating a design basis accident.
The proposed change does not involve a change in the plant design, system operation, or the use of the DGs. The proposed change requires the DGs to meet SR acceptance criteria that envelope the actual demand requirements for the DGs during design basis conditions. These revised acceptance criteria continue to demonstrate the capability and capacity of the DGs to perform their required functions. There are no new failure modes or mechanisms created due to testing the DGs within the proposed acceptance criteria. Testing of the DGs at the proposed acceptance criteria does not involve any modification in the CNL-16-001                                   E17 of 20
 
ENCLOSURE operational limits or physical design of plant systems. There are no new accident precursors generated due to the proposed test loadings.
Therefore, the proposed change does not create the possibility of a new or different kind of accident from any accident previously evaluated.
: 3.     Does the proposed amendment involve a significant reduction in a margin of safety?
Response: No.
The proposed change will continue to demonstrate that the DGs meet the TS definition of operability, that is, the proposed acceptance criteria will continue to demonstrate that the DGs will perform their safety function. The proposed testing will also continue to demonstrate the capability and capacity of the DGs to supply their required loads for mitigating a design basis accident.
The proposed change does not alter the manner in which safety limits, limiting safety system settings or limiting conditions for operation are determined. The safety analysis acceptance criteria are not affected by this change. The proposed change will not result in plant operation in a configuration outside the design basis.
The proposed change does not alter the manner in which safety limits, limiting safety system settings or limiting conditions for operation are determined. The safety analysis acceptance criteria are not affected by this change. The proposed change will not result in plant operation in a configuration outside the design basis.
Therefore, the proposed change does not involve a significant reduction in a margin of safety.
Therefore, the proposed change does not involve a significant reduction in a margin of safety.
Based on the above, TVA concludes that the proposed amendment does not involve a significant hazards consideration under the standards set forth in 10 CFR 50.92 (c), and, accordingly, a finding of "no significant hazards consideration" is justified.
Based on the above, TVA concludes that the proposed amendment does not involve a significant hazards consideration under the standards set forth in 10 CFR 50.92 (c), and, accordingly, a finding of no significant hazards consideration is justified.
In conclusion, based on the considerations discussed above, (1) there is reasonable assurance that the health and safety of the public will not be endangered by operation in the proposed manner, (2) such activities will be conducted in compliance with the Commission's regulations, and (3) the issuance of the amendment will not be inimical to the common defense and security or to the health and safety of the public.
4.4  Conclusion In conclusion, based on the considerations discussed above, (1) there is reasonable assurance that the health and safety of the public will not be endangered by operation in the proposed manner, (2) such activities will be conducted in compliance with the Commissions regulations, and (3) the issuance of the amendment will not be inimical to the common defense and security or to the health and safety of the public.
 
==5.0  ENVIRONMENTAL CONSIDERATION==
 
A review has determined that the proposed amendment would change a requirement with respect to installation or use of a facility component located within the restricted area, as defined in 10 CFR 20, or would change an inspection or surveillance requirement. However, the proposed amendment does not involve (i) a significant hazards consideration, (ii) a significant change in the types or significant increase in the amounts of any effluents that may be released offsite, or (iii) a significant increase in individual or cumulative occupational radiation exposure. Accordingly, the proposed amendment meets the eligibility criterion for categorical exclusion set forth in 10 CFR 51.22(c)(9). Therefore, pursuant to 10 CFR 51.22(b), no environmental impact statement or environmental assessment need be prepared in connection with the proposed amendment.
A review has determined that the proposed amendment would change a requirement with respect to installation or use of a facility component located within the restricted area, as defined in 10 CFR 20, or would change an inspection or surveillance requirement. However, the proposed amendment does not involve (i) a significant hazards consideration, (ii) a significant change in the types or significant increase in the amounts of any effluents that may be released offsite, or (iii) a significant increase in individual or cumulative occupational radiation exposure. Accordingly, the proposed amendment meets the eligibility criterion for categorical exclusion set forth in 10 CFR 51.22(c)(9). Therefore, pursuant to 10 CFR 51.22(b), no environmental impact statement or environmental assessment need be prepared in connection with the proposed amendment.
ENCLOSURE    CNL-16-001 E 19 of 20   1. TVA Letter to NRC, CNL 218, "Application to Modify Watts Bar Nuclear Plant, Unit 1 Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (SQN
CNL-16-001                                     E18 of 20
-TS-13-08)," dated April 6, 2015 (ML15117A462)
 
: 2. NRC letter to TVA, "Watts Bar Nuclear Plant, Unit 1 - Issuance of Amendment Regarding Modification To Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (TAC N
ENCLOSURE
: o. MF6153)," dated September 17, 2015 (ML15230A155)
: 3. Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for


Standby Power Supplies" 4. NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998
==6.0  REFERENCES==
: 5. Regulatory Guide 1.9, Revision 1, "Selection, Design, and Qualification of Diesel
: 1. TVA Letter to NRC, CNL-14-218, Application to Modify Watts Bar Nuclear Plant, Unit 1 Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (SQN-TS-13-08), dated April 6, 2015 (ML15117A462)
-Generator Units Used as Onsite Electric Power Systems at Nuclear Power Plants" 6. WCAP-17308-NP, Treatment of Diesel Generator (DG) Technical Specification Frequency and Voltage Tolerances, April 2012
: 2. NRC letter to TVA, Watts Bar Nuclear Plant, Unit 1 - Issuance of Amendment Regarding Modification To Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (TAC No. MF6153), dated September 17, 2015 (ML15230A155)
: 3. Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies"
: 4. NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998
: 5. Regulatory Guide 1.9, Revision 1, "Selection, Design, and Qualification of Diesel-Generator Units Used as Onsite Electric Power Systems at Nuclear Power Plants"
: 6. WCAP-17308-NP, Treatment of Diesel Generator (DG) Technical Specification Frequency and Voltage Tolerances, April 2012
: 7. G-Spec G-37 R5, Testing and Balancing of HVAC Systems During Installation, Modification, and Maintenance
: 7. G-Spec G-37 R5, Testing and Balancing of HVAC Systems During Installation, Modification, and Maintenance
: 8. Regulatory Guide 1.6, Revision 0, "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems (Safety Guide 6)" 9. NUREG-1232, Volume 2, "Safety Evaluation Report On Tennessee Valley Authority: Sequoyah Nuclear Performance Plan," dated May 1988 10. NRC Letter, "Beaver Valley 1 and 2 - Amendment for Revised Technical Specification Requirements for Emergency Diesel Generators (TAC Nos. MA4438 and MA4439)," dated February 11, 2000 (ML003684928)
: 8. Regulatory Guide 1.6, Revision 0, "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems (Safety Guide 6)"
: 11. NRC Letter, "Palo Verde Nuclear Generating Station, Units 1, 2, and 3 - Issuance of Amendments on Diesel Generator Steady
: 9. NUREG-1232, Volume 2, Safety Evaluation Report On Tennessee Valley Authority: Sequoyah Nuclear Performance Plan, dated May 1988
-State Voltage and Frequency (TAC Nos. MA9214, MA9215, and MA9216)," dated October 4, 2000 (ML003758500)
: 10. NRC Letter, "Beaver Valley 1 and 2 - Amendment for Revised Technical Specification Requirements for Emergency Diesel Generators (TAC Nos. MA4438 and MA4439)," dated February 11, 2000 (ML003684928)
: 12. NRC Letter, "Donald C. Cook Nuclear Plant, Units 1 and 2 - Issuance of Amendment to Renewed Facility Operating License Regarding Technical Specification Change Relating to Diesel Generator Steady
: 11. NRC Letter, "Palo Verde Nuclear Generating Station, Units 1, 2, and 3 - Issuance of Amendments on Diesel Generator Steady-State Voltage and Frequency (TAC Nos. MA9214, MA9215, and MA9216)," dated October 4, 2000 (ML003758500)
-State Parameters (TAC Nos. MD8773 and MD8774)," dated April 30, 2009 (ML090630245)
: 12. NRC Letter, Donald C. Cook Nuclear Plant, Units 1 and 2 - Issuance of Amendment to Renewed Facility Operating License Regarding Technical Specification Change Relating to Diesel Generator Steady-State Parameters (TAC Nos. MD8773 and MD8774), dated April 30, 2009 (ML090630245)
: 13. NRC Letter, "Crystal River Unit 3 Nuclear Generating Plant - Issuance of Amendment Regarding Request to Revise the Technical Specification Surveillance Requirements for Emergency Diesel Generator Voltage and Frequency Limits (TAC No. ME0107)," dated December 10, 2009 (ML092680285)
: 13. NRC Letter, "Crystal River Unit 3 Nuclear Generating Plant - Issuance of Amendment Regarding Request to Revise the Technical Specification Surveillance Requirements for Emergency Diesel Generator Voltage and Frequency Limits (TAC No. ME0107), dated December 10, 2009 (ML092680285)
CNL-16-001                                E19 of 20


ENCLOSURE   CNL-16-001 E 20 of 20  14. NRC Letter, "Wolf Creek Generating Station - Issuance of Amendment Re: Revise Technical Specification 3.8.1, "AC Sources - Operating" (TAC No. ME7674)," dated April 11, 2013 (ML13077A147)
ENCLOSURE
: 14. NRC Letter, "Wolf Creek Generating Station - Issuance of Amendment Re: Revise Technical Specification 3.8.1, "AC Sources - Operating" (TAC No. ME7674),"
dated April 11, 2013 (ML13077A147)
CNL-16-001                                E20 of 20


AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-6 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
ATTACHMENT 1 Proposed TS Changes (Mark-Ups) for SQN Units 1 and 2
SURVEILLANCE FREQUENCY  SR  3.8.1.2
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading. 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
    ---------------------------------------------------------------------
Verify each DG starts from standby conditions and  6800 V and 7260  58.8 Hz  61.2 Hz.       


In accordance with the Surveillance Frequency Control Program   SR 3.8.1.3
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
------------------------------NOTES-----------------------------
SURVEILLANCE                                                  FREQUENCY SR 3.8.1.2    ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
Verify each DG starts from standby conditions and                      In accordance achieves steady state voltage  6800 V and                            with the 7260 V, and frequency  58.8 Hz and  61.2 Hz.                      Surveillance Frequency Control Program 59.8                                        60.2 SR 3.8.1.3   ------------------------------NOTES-----------------------------
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 2. Momentary transients outside the load range do not invalidate this test.
: 2. Momentary transients outside the load range do not invalidate this test.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.   ---------------------------------------------------------------------
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.
Verify each DG is synchronized and loaded and                          In accordance operates for  60 minutes at a load  3960 kW and                      with the 4400 kW.                                                            Surveillance Frequency Control Program SEQUOYAH - UNIT 1                              3.8.1-6                                    Amendment 334


Verify each DG is synchronized and loaded and  60 minutes at a load 3960 kW and  4400 kW.  
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE                                                  FREQUENCY SR 3.8.1.4    Verify each engine-mounted day tank contains                        In accordance 250 gal of fuel oil.                                                with the Surveillance Frequency Control Program SR 3.8.1.5    Check for and remove accumulated water from each                      In accordance engine-mounted day tank.                                            with the Surveillance Frequency Control Program SR 3.8.1.6    Verify the fuel oil transfer system operates to                        In accordance transfer fuel oil from the storage system to the                      with the engine-mounted day tanks.                                            Surveillance Frequency Control Program SR 3.8.1.7    ------------------------------NOTE-------------------------------
All DG starts may be preceded by an engine prelube period.
Verify each DG starts from standby condition and                      In accordance achieves:                                                              with the Surveillance
: a. In  10 seconds, voltage  6800 V and                            Frequency frequency  58.8 Hz and                                         Control Program
: b. Steady state voltage  6800 V and  7260 V, and frequency 58.8 Hz and  61.2 Hz.
59.8                60.2 SEQUOYAH - UNIT 1                              3.8.1-7                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-7 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.4 Verify each engine
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.8    ------------------------------NOTES-----------------------------
-mounted "day" tank contains  250 gal of fuel oil.
: 1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.5 Check for and remove accumulated water from each engine-mounted "day" tank.
: 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
In accordance with the Surveillance Frequency Control Program   SR  3.8.1.6 Verify the fuel oil transfer system operates to transfer fuel oil from the storage system to the engine-mounted "day" tanks.
Verify automatic and manual transfer of the power                     In accordance supply to each 6.9 kV Unit Board from the normal                       with the supply to the alternate supply.                                       Surveillance Frequency Control Program SR 3.8.1.9   ------------------------------NOTE------------------------------
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.7
------------------------------NOTE-------------------------------
All DG starts may be preceded by an engine prelube period.  ---------------------------------------------------------------------
 
Verify each DG starts from standby condition and achieves:    a. In  10 seconds, volta 6800 V and  58.8 Hz and    b. Steady state voltage  6800 V and  7260 V, and frequency  58.8 Hz and  61.2 Hz.        In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1  SEQUOYAH - UNIT 1 3.8.1-8 Amendment 334 SURVEILLANCE REQUIREMENTS  (continued)
SURVEILLANCE FREQUENCY  SR  3.8.1.8
------------------------------NOTE S-----------------------------
: 1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR. 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
---------------------------------------------------------------------
Verify automatic and manual transfer of the power supply to each 6.9 kV Unit Board from the normal supply to the alternate supply.
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.9
------------------------------NOTE------------------------------
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
Under this condition the power factor shall be maintained as close to the limit as practicable.   ---------------------------------------------------------------------
Under this condition the power factor shall be maintained as close to the limit as practicable.
Verify each DG rejects a load greater than or equal                    In accordance to its associated single largest post-accident load,                  with the and:                                                                  Surveillance Frequency
: a. Following load rejection, the frequency is                      Control Program 66.5 Hz,
: b. Within 3 seconds following load rejection, the voltage is  6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is  58.8 Hz and  61.2 Hz.
SEQUOYAH - UNIT 1      59.8                  60.2 3.8.1-8                                    Amendment 334


Verify each DG rejects a load greater than or equal to its associated single largest post
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
-accident load, and:
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.11   ------------------------------NOTES-----------------------------
: a. Following load rejection, the frequency is  66.5 Hz,    b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is 58.8 Hz and  61.2 Hz.   
 
In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-10 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.11
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, thi s Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated loss of offsite power                 In accordance signal:                                                               with the Surveillance
Verify on an actual or simulated loss of offsite power signal:
: a. De-energization of shutdown boards,                             Frequency Control Program
: a. De-energization of shutdown boards,     b. Load shedding from shutdown boards,
: b. Load shedding from shutdown boards,
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in  10 seconds,
: 1.     Energizes permanently connected loads in  10 seconds,
: 2. Energizes auto
: 2.     Energizes auto-connected shutdown loads through load sequence timers,
-connected shutdown loads through load sequence timers,
: 3.     Maintains steady state voltage 6800 V and 7260 V,
: 3. Maintains steady state voltage 6800 V and   7260 V,
: 4.     Maintains steady state frequency 58.8 Hz and 61.2 Hz, and
: 4. Maintains steady state frequency 58.8 Hz and   61.2 Hz, and
: 5.     Supplies permanently connected and auto-connected shutdown loads for 59.8                  60.2 5 minutes.
: 5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.  
SEQUOYAH - UNIT 1                            3.8.1-10                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-11 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.12
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.12     ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by prelube period.
: 1. All DG starts may be preceded by prelube period. 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated Engineered Safety                     In accordance Feature (ESF) actuation signal each DG auto-starts                     with the from standby condition and:                                           Surveillance Frequency
Verify on an actual or simulated Engineered Safety Feature (ESF) actuation signal each DG auto
: a. In  10 seconds after auto-start and during                     Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
-starts from standby condition and:
: b. Achieves steady state voltage  6800 V and 7260 V and frequency  58.8 Hz and 61.2 Hz,
: a. 10 seconds after auto
: c. Operates for  5 minutes, 59.8 60.2 d. Permanently connected loads remain energized from the offsite power system, and
-start and during  6800 V and frequency 58.8 Hz,
: b. 6800 V and   58.8 Hz and 61.2 H z,     c. 5 minutes,     d. Permanently connected loads remain energized from the offsite power system, and
: e. Emergency loads are energized from the offsite power system.
: e. Emergency loads are energized from the offsite power system.
SEQUOYAH - UNIT 1                                3.8.1-11                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-13 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.15 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.15   ------------------------------NOTES-----------------------------
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours load 3960 kW and 4400 kW   2370 kvar.
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loaded  3960 kW and 4400 kW and  2140 kvar and  2370 kvar.
Momentary transients outside of load range do not invalidate this test.
Momentary transients outside of load range do not invalidate this test.
: 2. All DG starts may be preceded by an engine prelube period.
: 2. All DG starts may be preceded by an engine prelube period.
    ---------------------------------------------------------------------
Verify each DG starts and achieves:                                   In accordance with the
 
: a. In  10 seconds, voltage 6800 V and                           Surveillance frequency 58.8 Hz and                                         Frequency Control Program
Verify each DG starts and achieves:
: b. Steady state voltage  6800 V, and 7260 V and frequency 58.8 Hz and 61.2 Hz.
: a. 10  6800 V and  58.8 Hz and
SR 3.8.1.16   ------------------------------NOTE-------------------------------
: b. 6800  7260 V  58.8  61.2 Hz.  
For DGs 59.8 1A-A and 1B-B,   60.2this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
 
Verify each DG:                                                       In accordance with the
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.16 ------------------------------NOTE-------------------------------
: a. Synchronizes with offsite power source while                     Surveillance loaded with emergency loads upon a simulated                     Frequency restoration of offsite power,                                   Control Program
For DGs 1A
-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
  ---------------------------------------------------------------------
 
Verify each DG:
: a. Synchronizes with offsite power source while loaded with emergency loads upon a simulated restoration of offsite power,
: b. Transfers loads to offsite power source, and
: b. Transfers loads to offsite power source, and
: c. Returns to ready
: c. Returns to ready-to-load operation.
-to-load operation.
SEQUOYAH - UNIT 1                            3.8.1-13                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-15 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.18 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.18   ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated loss of offsite power                 In accordance signal in conjunction with an actual or simulated                     with the ESF actuation signal:                                                 Surveillance Frequency
 
: a. De-energization of shutdown boards,                               Control Program
Verify on an actual or simulated loss of offsite power signal in conjunction with an actual or simulated ESF actuation signal:
: b. Load shedding from shutdown boards, and
: a. De-energization of shutdown boards, b. Load shedding from shutdown boards, and
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in 10 seconds, 2. Energizes auto
: 1. Energizes permanently connected loads in 10 seconds,
-connected emergency loads through load sequence timers,
: 2. Energizes auto-connected emergency loads through load sequence timers,
: 3. 6800 V  7260 V,
: 3. Achieves steady state voltage  6800 V and 7260 V,
: 4. Ach 58.8 Hz  61.2 Hz, and 5. Supplies permanently connected and auto
: 4. Achieves steady state frequency  58.8 Hz and 61.2 Hz, and
-connected emergency loads for  5 minutes.  
: 5. Supplies permanently connected and auto-connected emergency 59.8      loads for 60.2 5 minutes.
SEQUOYAH - UNIT 1                            3.8.1-15                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-6 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.2
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.2   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading. 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
    ---------------------------------------------------------------------
Verify each DG starts from standby conditions and                     In accordance achieves steady state voltage 6800 V and                             with the 7260 V, and frequency 58.8 Hz and 61.2 Hz.                       Surveillance Frequency Control Program 59.8                                        60.2 SR 3.8.1.3   ------------------------------NOTES-----------------------------
Verify each DG starts from standby conditions and  6800 V and 7260  58.8 H z 61.2 H z.  
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.3
------------------------------NOTES-----------------------------
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 2. Momentary transients outside the load range do not invalidate this test.
: 2. Momentary transients outside the load range do not invalidate this test.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.   ---------------------------------------------------------------------
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.
 
Verify each DG is synchronized and loaded and                         In accordance operates for 60 minutes at a load  3960 kW and                     with the 4400 kW.                                                             Surveillance Frequency Control Program SEQUOYAH - UNIT 2                              3.8.1-6                                    Amendment 327
Verify each DG is synchronized and loaded and  60 minutes at a load  3960 kW and 4400 kW.  


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-7 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.4 Verify each engine
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.4   Verify each engine-mounted day tank contains                         In accordance 250 gal of fuel oil.                                                 with the Surveillance Frequency Control Program SR 3.8.1.5   Check for and remove accumulated water from each                       In accordance engine-mounted day tank.                                             with the Surveillance Frequency Control Program SR 3.8.1.6   Verify the fuel oil transfer system operates to                       In accordance transfer fuel oil from the storage system to the                      with the engine-mounted day tanks.                                           Surveillance Frequency Control Program SR 3.8.1.7   ------------------------------NOTE-------------------------------
-mounted "day" tank contains 250 gal of fuel oil.
All DG starts may be preceded by an engine prelube period.
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.5 Check for and remove accumulated water from each engine-mounted "day" tank.
Verify each DG starts from standby condition and                      In accordance achieves:                                                              with the Surveillance
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.6 Verify the fuel oil transfer system operates to transfer fuel oil from the storage system to the engine-mounted "day" tanks.
: a. In  10 seconds, voltage  6800 V and                            Frequency frequency  58.8 Hz and                                          Control Program
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.7
: b. Steady state voltage 6800 V and  7260 V, and frequency  58.8 Hz and  61.2 Hz.
------------------------------NOTE-------------------------------
59.8                                            60.2 SEQUOYAH - UNIT 2                              3.8.1-7                                    Amendment 327
All DG starts may be preceded by an engine prelube period.  ---------------------------------------------------------------------


Verify each DG starts from standby condition and achieves:    a. In  10 seconds, volta 6800 V and  58.8 Hz and    b. Steady state voltage  6800 V and  7260 V, and frequency  58.8 Hz and  61.2 Hz.        In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-8 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.8
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.8   ------------------------------NOTES-----------------------------
------------------------------NOTE S-----------------------------
: 1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
: 1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR. 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
: 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
---------------------------------------------------------------------
Verify automatic and manual transfer of the power                     In accordance supply to each 6.9 kV Unit Board from the normal                       with the supply to the alternate supply.                                       Surveillance Frequency Control Program SR 3.8.1.9   ------------------------------NOTE-------------------------------
Verify automatic and manual transfer of the power supply to each 6.9 kV Unit Board from the normal supply to the alternate supply.
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.9
------------------------------NOTE-------------------------------
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
Under this condition the power factor shall be maintained as close to the limit as practicable.   ---------------------------------------------------------------------
Under this condition the power factor shall be maintained as close to the limit as practicable.
Verify each DG rejects a load greater than or equal                    In accordance to its associated single largest post-accident load,                  with the and:                                                                  Surveillance Frequency
: a. Following load rejection, the frequency is                      Control Program 66.5 Hz,
: b. Within 3 seconds following load rejection, the voltage is  6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is  58.8 Hz and  61.2 Hz.
59.8                    60.2 SEQUOYAH - UNIT 2                              3.8.1-8                                    Amendment 327


Verify each DG rejects a load greater than or equal to its associated single largest post
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
-accident load, and:
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.11   ------------------------------NOTES-----------------------------
: a. Following load rejection, the frequency is  66.5 Hz,    b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is 58.8 Hz and  61.2 Hz.   
 
In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-10 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.11
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 2A-A and 2B-B, thi s Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated loss of offsite power signal:
Verify on an actual or simulated loss of offsite power                 In accordance signal:                                                               with the Surveillance
: a. De-energization of shutdown boards,     b. Load shedding from shutdown boards,
: a. De-energization of shutdown boards,                             Frequency Control Program
: b. Load shedding from shutdown boards,
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in  10 seconds,
: 1.     Energizes permanently connected loads in  10 seconds,
: 2. Energizes auto
: 2.     Energizes auto-connected shutdown loads through load sequence timers,
-connected shutdown loads through load sequence timers,
: 3.     Maintains steady state voltage 6800 V and 7260 V,
: 3. Maintains steady state voltage 6800 V and   7260 V,
: 4.     Maintains steady state frequency 58.8 Hz and 61.2 Hz, and
: 4. Maintains steady state frequency 58.8 Hz and   61.2 Hz, and
: 5.     Supplies permanently connected and auto-connected shutdown loads for 59.8                  60.2 5 minutes.
: 5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.  
SEQUOYAH - UNIT 2                            3.8.1-10                                    Amendment 327


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-11 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.12
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.12     ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by prelube period.
: 1. All DG starts may be preceded by prelube period. 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated Engineered Safety Feature (ESF) actuation signal each DG auto
Verify on an actual or simulated Engineered Safety                     In accordance Feature (ESF) actuation signal each DG auto-starts                     with the from standby condition and:                                           Surveillance Frequency
-starts from standby condition and:
: a. In  10 seconds after auto-start and during                     Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
: a. 10 seconds after auto
: b. Achieves steady state voltage  6800 V and 7260 V and frequency  58.8 Hz and 61.2 Hz,
-start and during  6800 V and frequency 58.8 Hz,
: c. Operates for  5 minutes, 59.8
: b. 6800 V and   58.8 Hz and 61.2 H z,     c. 5 minutes,     d. Permanently connected loads remain energized from the offsite power system, and
: d. Permanently connected loads remain energized 60.2      from the offsite power system, and
: e. Emergency loads are energized from the offsite power system.
: e. Emergency loads are energized from the offsite power system.
SEQUOYAH - UNIT 2                                3.8.1-11                                    Amendment 327


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-13 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.15 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.15   ------------------------------NOTES-----------------------------
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loa 3960 kW and 4400 kW   2370 kvar.
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loaded  3960 kW and 4400 kW and  2140 kvar and  2370 kvar.
Momentary transients outside of load range do not invalidate this test.
Momentary transients outside of load range do not invalidate this test.
: 2. All DG starts may be preceded by an engine prelube period.
: 2. All DG starts may be preceded by an engine prelube period.
    ---------------------------------------------------------------------
Verify each DG starts and achieves:                                   In accordance with the
 
: a. In  10 seconds, voltage 6800 V and                           Surveillance frequency 58.8 Hz and                                         Frequency Control Program
Verify each DG starts and achieves:
: b. Steady state voltage  6800 V, and 7260 V and frequency 58.8 Hz and 61.2 Hz.
: a. 10  6800 V and  58.8 Hz and
SR 3.8.1.16   ------------------------------NOTE-------------------------------
: b. 6800  7260 V  58.8  61.2 Hz.  
For DGs 59.82A-A and 2B-B, this Surveillance shall         60.2not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
 
Verify each DG:                                                       In accordance with the
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.16 ------------------------------NOTE-------------------------------
: a. Synchronizes with offsite power source while                     Surveillance loaded with emergency loads upon a simulated                     Frequency restoration of offsite power,                                   Control Program
For DGs 2A-A and 2B-B, this Surveillance shall no t normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
  ---------------------------------------------------------------------
 
Verify each DG:
: a. Synchronizes with offsite power source while loaded with emergency loads upon a simulated restoration of offsite power,
: b. Transfers loads to offsite power source, and
: b. Transfers loads to offsite power source, and
: c. Returns to ready
: c. Returns to ready-to-load operation.
-to-load operation.
SEQUOYAH - UNIT 2                            3.8.1-13                                    Amendment 327


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-15 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.18 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.18   ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated loss of offsite power signal in conjunction with an actual or simulated ESF actuation signal:
Verify on an actual or simulated loss of offsite power                 In accordance signal in conjunction with an actual or simulated                     with the ESF actuation signal:                                                 Surveillance Frequency
: a. De-energization of shutdown boards, b. Load shedding from shutdown boards, and
: a. De-energization of shutdown boards,                               Control Program
: b. Load shedding from shutdown boards, and
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in 10 seconds, 2. Energizes auto
: 1. Energizes permanently connected loads in 10 seconds,
-connected emergency loads through load sequence timers,
: 2. Energizes auto-connected emergency loads through load sequence timers,
: 3. 6800 V  7260 V,
: 3. Achieves steady state voltage  6800 V and 7260 V,
: 4. Ach 58.8 Hz  61.2 Hz, and 5. Supplies permanently connected and auto
: 4. Achieves steady state frequency  58.8 Hz and 61.2 Hz, and
-connected emergency loads for 5 minutes.  
: 5. Supplies permanently connected and auto-connected emergency loads       59.8 for 5 minutes. 60.2 SEQUOYAH - UNIT 2                            3.8.1-15                                    Amendment 327
 
In accordance with the Surveillance Frequency Control Program 


AC Sources - Operating B 3.8.1    SEQUOYAH - UNIT 1 B 3.8.1-16 Revision 45 BASES  SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8). Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref.
ATTACHMENT 2 Proposed TS Bases Changes (Mark-Ups) for SQN Units 1 and 2 (For Information Only)
9).
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable.
The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating. The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages. The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/-
2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).
SR  3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained. 


AC Sources - Operating B 3.8.1 BASES SURVEILLANCE    The AC sources are designed to permit inspection and testing of all REQUIREMENTS    important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).
Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.
The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.
The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/- 2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3).
These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
SEQUOYAH - UNIT 1                      B 3.8.1-16                                    Revision 45


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 1 B 3.8.1-17 Revision 45 BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 During this testing, the diesel is BASES                                                     not in an accident mode and the frequency is controlled by SURVEILLANCE REQUIREMENTS (continued)                     the operator instead of the governors accident speed SR 3.8.1.2 and SR 3.8.1.7                 reference.
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
 
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2. SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.
SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 1                      B 3.8.1-17                                    Revision 45


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 1 B 3.8.1-21 Revision 45 BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post-accident load with the DG solely supplying the board.       and Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejectionmaximum test is   transient acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
: b. Tripping its associated single largest post
-accident load with the DG solely supplying the board. Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
 
The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.
The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than  0.89.
These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to  0.89 results in voltages on the emergency boards that are too high.
SEQUOYAH - UNIT 1                        B 3.8.1-21                              Revision 45


This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows  0.89. These conditions occur when grid voltage is high, and the additional field 0.89 results in voltages on the emergency boards that are too high. 
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE     The AC sources are designed to permit inspection and testing of all REQUIREMENTS     important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).
 
Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).
AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-16 Revision 44 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8). Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref.
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.
9). Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating. The specified maximum steady state output voltage o f 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages. The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/-
The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.
2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).
The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/- 2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
 
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.                         The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3).
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
 
SEQUOYAH - UNIT 2                       B 3.8.1-16                                    Revision 44
AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-17 Revision 45 BASES  SURVEILLANCE REQUIREMENTS  (continued)
SR  3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.


AC Sources - Operating B 3.8.1 During this testing, the diesel is not in an accident mode and BASES                                                          the frequency is controlled by the operator instead of the SURVEILLANCE REQUIREMENTS (continued)                          governors accident speed reference.
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2. SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.
SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 2                      B 3.8.1-17                                  Revision 45


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-21 Revision 45 BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post-accident load with the DG solely supplying the board.       and Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejectionmaximum test is   transient acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
: b. Tripping its associated single largest post
-accident load with the DG solely supplying the board. Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
 
The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.
The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than  0.89.
These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to  0.89 results in voltages on the emergency boards that are too high.
SEQUOYAH - UNIT 2                        B 3.8.1-21                              Revision 45


This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows  0.89. These conditions occur when grid voltage is high, and the additional field 0.89 results in voltages on the emergency boards that are too high.
ATTACHMENT 3 Proposed TS Changes (Final Typed) for SQN Units 1 and 2


AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-6 Amendment 33 X  SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.2
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.2   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
    ---------------------------------------------------------------------
Verify each DG starts from standby conditions and                     In accordance achieves steady state voltage 6800 V and                             with the 7260 V, and frequency 59.8 Hz and 60.2 Hz.                       Surveillance Frequency Control Program SR 3.8.1.3   ------------------------------NOTES-----------------------------
Verify each DG starts from standby conditions and  6800 V and 7260  59.8 Hz  60.2 Hz.      
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.3
------------------------------NOTES-----------------------------
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 2. Momentary transients outside the load range do not invalidate this test.
: 2. Momentary transients outside the load range do not invalidate this test.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.   ---------------------------------------------------------------------
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.
Verify each DG is synchronized and loaded and                          In accordance operates for  60 minutes at a load  3960 kW and                      with the 4400 kW.                                                            Surveillance Frequency Control Program SEQUOYAH - UNIT 1                              3.8.1-6                                  Amendment 33X


Verify each DG is synchronized and loaded and  60 minutes at a load 3960 kW and  4400 kW.  
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE                                                  FREQUENCY SR 3.8.1.4    Verify each engine-mounted day tank contains                        In accordance 250 gal of fuel oil.                                                with the Surveillance Frequency Control Program SR 3.8.1.5    Check for and remove accumulated water from each                      In accordance engine-mounted day tank.                                            with the Surveillance Frequency Control Program SR 3.8.1.6    Verify the fuel oil transfer system operates to                        In accordance transfer fuel oil from the storage system to the                      with the engine-mounted day tanks.                                            Surveillance Frequency Control Program SR 3.8.1.7    ------------------------------NOTE-------------------------------
All DG starts may be preceded by an engine prelube period.
Verify each DG starts from standby condition and                      In accordance achieves:                                                              with the Surveillance
: a. In  10 seconds, voltage  6800 V and                           Frequency frequency  58.8 Hz and                                         Control Program
: b. Steady state voltage 6800 V and 7260 V, and frequency 59.8 Hz and  60.2 Hz.
SEQUOYAH - UNIT 1                              3.8.1-7                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-7 Amendment 33 X  SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR  3.8.1.4 Verify each engine
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.8    ------------------------------NOTES-----------------------------
-mounted "day" tank contains  250 gal of fuel oil.
: 1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.5 Check for and remove accumulated water from each engine-mounted "day" tank.
: 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.6 Verify the fuel oil transfer system operates t o  transfer fuel oil from the storage system to the engine-mounted "day" tanks.
Verify automatic and manual transfer of the power                     In accordance supply to each 6.9 kV Unit Board from the normal                       with the supply to the alternate supply.                                       Surveillance Frequency Control Program SR 3.8.1.9   ------------------------------NOTE------------------------------
In accordance with the Surveillance Frequency Control Program   SR  3.8.1.7
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
------------------------------NOTE-------------------------------
Under this condition the power factor shall be maintained as close to the limit as practicable.
All DG starts may be preceded by an engine prelube period.  ---------------------------------------------------------------------
Verify each DG rejects a load greater than or equal                   In accordance to its associated single largest post-accident load,                   with the and:                                                                   Surveillance Frequency
 
: a. Following load rejection, the frequency is                       Control Program 66.5 Hz,
Verify each DG starts from standby condition and achieves:    a. In  10 seconds, vol 6800 V and  58.8 Hz and
: b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: b. Steady state voltage  6800 V and  7260 V, and frequency  59.8 Hz and  60.2 Hz.        In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1  SEQUOYAH - UNIT 1 3.8.1-8 Amendment 33 X  SURVEILLANCE REQUIREMENTS  (continued)
: c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and  60.2 Hz.
SURVEILLANCE FREQUENCY  SR  3.8.1.8
SEQUOYAH - UNIT 1                              3.8.1-8                                  Amendment 33X
------------------------------NOTE S-----------------------------
: 1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR. 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
---------------------------------------------------------------------
Verify automatic and manual transfer of the power supply to each 6.9 kV Unit Board from the normal supply to the alternate supply.
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.9
------------------------------NOTE------------------------------
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met. Under this condition the power factor shall be maintained as close to the limit as practicable.   ---------------------------------------------------------------------
 
Verify each DG rejects a load greater than or equal to its associated single largest post
-accident load, and:
: a. Following load rejection, the frequency is 66.5 Hz,     b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and  60.2 Hz.  


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-10 Amendment 33X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.11
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.11   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, th is Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated loss of offsite power                 In accordance signal:                                                               with the Surveillance
Verify on an actual or simulated loss of offsite power signal:
: a. De-energization of shutdown boards,                             Frequency Control Program
: a. De-energization of shutdown boards,     b. Load shedding from shutdown boards,
: b. Load shedding from shutdown boards,
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in  10 seconds,
: 1.     Energizes permanently connected loads in  10 seconds,
: 2. Energizes auto
: 2.     Energizes auto-connected shutdown loads through load sequence timers,
-connected shutdown loads through load sequence timers,
: 3.     Maintains steady state voltage 6800 V and 7260 V,
: 3. Maintains steady state voltage 6800 V and   7260 V,
: 4.     Maintains steady state frequency 59.8 Hz and 60.2 Hz, and
: 4. Maintains steady state frequency 59.8 Hz and   60.2 Hz, and
: 5.     Supplies permanently connected and auto-connected shutdown loads for 5 minutes.
: 5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.        
SEQUOYAH - UNIT 1                            3.8.1-10                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-11 Amendment 33X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.12
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.12   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by prelube period.
: 1. All DG starts may be preceded by prelube period. 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated Engineered Safety                     In accordance Feature (ESF) actuation signal each DG auto-starts                     with the from standby condition and:                                           Surveillance Frequency
Verify on an actual or simulated Engineered Safety Feature (ESF) actuation signal each DG auto
: a. In  10 seconds after auto-start and during                     Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
-starts from standby condition and:
: b. Achieves steady state voltage  6800 V and 7260 V and frequency  59.8 Hz and 60.2 Hz,
: a. 10 seconds after auto
: c. Operates for  5 minutes,
-start and during  6800 V and frequency 58.8 Hz,
: d. Permanently connected loads remain energized from the offsite power system, and
: b. 6800 V and   59.8 Hz and 60.2 Hz,     c. 5 minutes,     d. Permanently connected loads remain energized from the offsite power system, and
: e. Emergency loads are energized from the offsite power system.
: e. Emergency loads are energized from the offsite power system.
SEQUOYAH - UNIT 1                            3.8.1-11                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-13 Amendment 33X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.15 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.15   ------------------------------NOTES-----------------------------
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loa 3960 kW and 4400 kW   2370 kvar.
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loaded  3960 kW and 4400 kW and  2140 kvar and  2370 kvar.
Momentary transients outside of load range do not invalidate this test.
Momentary transients outside of load range do not invalidate this test.
: 2. All DG starts may be preceded by an engine prelube period.
: 2. All DG starts may be preceded by an engine prelube period.
    ---------------------------------------------------------------------
Verify each DG starts and achieves:                                   In accordance with the
 
: a. In  10 seconds, voltage 6800 V and                           Surveillance frequency 58.8 Hz and                                         Frequency Control Program
Verify each DG starts and achieves:
: b. Steady state voltage  6800 V, and 7260 V and frequency 59.8 Hz and 60.2 Hz.
: a. 10  6800 V and  58.8 Hz and
SR 3.8.1.16   ------------------------------NOTE-------------------------------
: b. 6800  7260 V  59.8  60.2 Hz.  
For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
 
Verify each DG:                                                       In accordance with the
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.16 ------------------------------NOTE-------------------------------
: a. Synchronizes with offsite power source while                     Surveillance loaded with emergency loads upon a simulated                     Frequency restoration of offsite power,                                   Control Program
For DGs 1A
-A and 1B-B, this Surveillance shall no t normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
  ---------------------------------------------------------------------
 
Verify each DG:
: a. Synchronizes with offsite power source while loaded with emergency loads upon a simulated restoration of offsite power,
: b. Transfers loads to offsite power source, and
: b. Transfers loads to offsite power source, and
: c. Returns to ready
: c. Returns to ready-to-load operation.
-to-load operation.
SEQUOYAH - UNIT 1                            3.8.1-13                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-15 Amendment 33X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.18 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.18   ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, t his Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated loss of offsite power                 In accordance signal in conjunction with an actual or simulated                     with the ESF actuation signal:                                                 Surveillance Frequency
Verify on an actual or simulated loss of offsite power signal in conjunction with an actual or simulated ESF actuation signal:
: a. De-energization of shutdown boards,                               Control Program
: a. De-energization of shutdown boards, b. Load shedding from shutdown boards, and
: b. Load shedding from shutdown boards, and
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in 10 seconds, 2. Energizes auto
: 1. Energizes permanently connected loads in 10 seconds,
-connected emergency loads through load sequence timers,
: 2. Energizes auto-connected emergency loads through load sequence timers,
: 3. 6800 V  7260 V,
: 3. Achieves steady state voltage  6800 V and 7260 V,
: 4. Ach i 59.8 Hz  60.2 Hz, and 5. Supplies permanently connected and auto
: 4. Achieves steady state frequency  59.8 Hz and 60.2 Hz, and
-connected emergency loads for 5 minutes.  
: 5. Supplies permanently connected and auto-connected emergency loads for 5 minutes.
SEQUOYAH - UNIT 1                            3.8.1-15                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-6 Amendment 32X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.2
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.2   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
    ---------------------------------------------------------------------
Verify each DG starts from standby conditions and                     In accordance achieves steady state voltage 6800 V and                             with the 7260 V, and frequency 59.8 Hz and 60.2 Hz.                       Surveillance Frequency Control Program SR 3.8.1.3   ------------------------------NOTES-----------------------------
Verify each DG starts from standby conditions and  6800 V and 7260  59.8 Hz  60.2 Hz.      
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.3
------------------------------NOTES-----------------------------
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 2. Momentary transients outside the load range do not invalidate this test.
: 2. Momentary transients outside the load range do not invalidate this test.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.   ---------------------------------------------------------------------
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.
Verify each DG is synchronized and loaded and                          In accordance operates for  60 minutes at a load  3960 kW and                      with the 4400 kW.                                                            Surveillance Frequency Control Program SEQUOYAH - UNIT 2                              3.8.1-6                                  Amendment 32X


Verify each DG is synchronized and loaded and  60 minutes at a load 3960 kW and  4400 kW.  
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE                                                  FREQUENCY SR 3.8.1.4    Verify each engine-mounted day tank contains                        In accordance 250 gal of fuel oil.                                                with the Surveillance Frequency Control Program SR 3.8.1.5    Check for and remove accumulated water from each                      In accordance engine-mounted day tank.                                            with the Surveillance Frequency Control Program SR 3.8.1.6    Verify the fuel oil transfer system operates to                        In accordance transfer fuel oil from the storage system to the                      with the engine-mounted day tanks.                                            Surveillance Frequency Control Program SR 3.8.1.7    ------------------------------NOTE-------------------------------
All DG starts may be preceded by an engine prelube period.
Verify each DG starts from standby condition and                      In accordance achieves:                                                              with the Surveillance
: a. In  10 seconds, voltage  6800 V and                           Frequency frequency  58.8 Hz and                                         Control Program
: b. Steady state voltage 6800 V and 7260 V, and frequency 59.8 Hz and  60.2 Hz.
SEQUOYAH - UNIT 2                              3.8.1-7                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-7 Amendment 32X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.4 Verify each engine
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.8    ------------------------------NOTES-----------------------------
-mounted "day" tank contains  250 gal of fuel oil.
: 1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.5 Check for and remove accumulated water from each engine-mounted "day" tank.
: 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
In accordance with the Surveillance Frequency Control Program   SR  3.8.1.6 Verify the fuel oil transfer system operates t o  transfer fuel oil from the storage system to the engine-mounted "day" tanks.
Verify automatic and manual transfer of the power                     In accordance supply to each 6.9 kV Unit Board from the normal                       with the supply to the alternate supply.                                       Surveillance Frequency Control Program SR 3.8.1.9   ------------------------------NOTE-------------------------------
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.7
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
------------------------------NOTE-------------------------------
Under this condition the power factor shall be maintained as close to the limit as practicable.
All DG starts may be preceded by an engine prelube period.  ---------------------------------------------------------------------
Verify each DG rejects a load greater than or equal                    In accordance to its associated single largest post-accident load,                  with the and:                                                                  Surveillance Frequency
Verify each DG starts from standby condition and achieves:    a. In  10 seconds, volt 6800 V and  58.8 Hz and
: a. Following load rejection, the frequency is                      Control Program 66.5 Hz,
: b. Steady state voltage  6800 V and  7260 V, and frequency  59.8 Hz and  60.2 Hz.        In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1  SEQUOYAH - UNIT 2 3.8.1-8 Amendment 32X SURVEILLANCE REQUIREMENTS  (continued)
: b. Within 3 seconds following load rejection, the voltage is  6800 V and  7260 V, and
SURVEILLANCE FREQUENCY  SR  3.8.1.8
: c. Within 3 seconds following load rejection, the frequency is  59.8 Hz and  60.2 Hz.
------------------------------NOTE S-----------------------------
SEQUOYAH - UNIT 2                              3.8.1-8                                  Amendment 32X
: 1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR. 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
---------------------------------------------------------------------
Verify automatic and manual transfer of the power supply to each 6.9 kV Unit Board from the normal supply to the alternate supply.
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.9
------------------------------NOTE-------------------------------
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met. Under this condition the power factor shall be maintained as close to the limit as practicable.   ---------------------------------------------------------------------


Verify each DG rejects a load greater than or equal to its associated single largest post
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
-accident load, and:
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.11   ------------------------------NOTES-----------------------------
: a. Following load rejection, the frequency is  66.5 Hz,    b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and  60.2 Hz.   
 
In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-10 Amendment 32X  SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.11
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 2A-A and 2B-B, thi s Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated loss of offsite power signal:
Verify on an actual or simulated loss of offsite power                 In accordance signal:                                                               with the Surveillance
: a. De-energization of shutdown boards,     b. Load shedding from shutdown boards,
: a. De-energization of shutdown boards,                             Frequency Control Program
: b. Load shedding from shutdown boards,
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in  10 seconds,
: 1.     Energizes permanently connected loads in  10 seconds,
: 2. Energizes auto
: 2.     Energizes auto-connected shutdown loads through load sequence timers,
-connected shutdown loads through load sequence timers,
: 3.     Maintains steady state voltage 6800 V and 7260 V,
: 3. Maintains steady state voltage 6800 V and   7260 V,
: 4.     Maintains steady state frequency 59.8 Hz and 60.2 Hz, and
: 4. Maintains steady state frequency 59.8 Hz and   60.2 Hz, and
: 5.     Supplies permanently connected and auto-connected shutdown loads for 5 minutes.
: 5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.        
SEQUOYAH - UNIT 2                            3.8.1-10                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-11 Amendment 32X  SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.12
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.12   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by prelube period.
: 1. All DG starts may be preceded by prelube period. 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated Engineered Safety Feature (ESF) actuation signal each DG auto
Verify on an actual or simulated Engineered Safety                     In accordance Feature (ESF) actuation signal each DG auto-starts                     with the from standby condition and:                                           Surveillance Frequency
-starts from standby condition and:
: a. In  10 seconds after auto-start and during                     Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
: a. 10 seconds after auto
: b. Achieves steady state voltage  6800 V and 7260 V and frequency  59.8 Hz and 60.2 Hz,
-start and during  6800 V and frequency 58.8 Hz,
: c. Operates for  5 minutes,
: b. 6800 V and   59.8 Hz and 60.2 Hz,     c. 5 minutes,     d. Permanently connected loads remain energized from the offsite power system, and
: d. Permanently connected loads remain energized from the offsite power system, and
: e. Emergency loads are energized from the offsite power system.
: e. Emergency loads are energized from the offsite power system.
SEQUOYAH - UNIT 2                            3.8.1-11                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-13 Amendment 32X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.15 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.15   ------------------------------NOTES-----------------------------
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loa 3960 kW and 4400 kW   2370 kvar.
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loaded  3960 kW and 4400 kW and  2140 kvar and  2370 kvar.
Momentary transients outside of load range do not invalidate this test.
Momentary transients outside of load range do not invalidate this test.
: 2. All DG starts may be preceded by an engine prelube period.
: 2. All DG starts may be preceded by an engine prelube period.
    ---------------------------------------------------------------------
Verify each DG starts and achieves:                                   In accordance with the
 
: a. In  10 seconds, voltage 6800 V and                           Surveillance frequency 58.8 Hz and                                         Frequency Control Program
Verify each DG starts and achieves:
: b. Steady state voltage  6800 V, and 7260 V and frequency 59.8 Hz and 60.2 Hz.
: a. 10  6800 V and  58.8 Hz and
SR 3.8.1.16   ------------------------------NOTE-------------------------------
: b. 6800  7260 V  59.8  60.2 Hz.  
 
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.16 ------------------------------NOTE-------------------------------
For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
  ---------------------------------------------------------------------
Verify each DG:                                                       In accordance with the
 
: a. Synchronizes with offsite power source while                     Surveillance loaded with emergency loads upon a simulated                     Frequency restoration of offsite power,                                   Control Program
Verify each DG:
: a. Synchronizes with offsite power source while loaded with emergency loads upon a simulated restoration of offsite power,
: b. Transfers loads to offsite power source, and
: b. Transfers loads to offsite power source, and
: c. Returns to ready
: c. Returns to ready-to-load operation.
-to-load operation.
SEQUOYAH - UNIT 2                            3.8.1-13                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-15 Amendment 32X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.18 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.18   ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 2A-A and 2B-B, t his Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated loss of offsite power signal in conjunction with an actual or simulated ESF actuation signal:
Verify on an actual or simulated loss of offsite power                 In accordance signal in conjunction with an actual or simulated                     with the ESF actuation signal:                                                 Surveillance Frequency
: a. De-energization of shutdown boards, b. Load shedding from shutdown boards, and
: a. De-energization of shutdown boards,                               Control Program
: b. Load shedding from shutdown boards, and
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in 10 seconds, 2. Energizes auto
: 1. Energizes permanently connected loads in 10 seconds,
-connected emergency loads through load sequence timers,
: 2. Energizes auto-connected emergency loads through load sequence timers,
: 3. 6800 V  7260 V,
: 3. Achieves steady state voltage  6800 V and 7260 V,
: 4. Ach 59.8 Hz  60.2 Hz, and 5. Supplies permanently connected and auto
: 4. Achieves steady state frequency  59.8 Hz and 60.2 Hz, and
-connected emergency loads for 5 minutes.  
: 5. Supplies permanently connected and auto-connected emergency loads for 5 minutes.
SEQUOYAH - UNIT 2                            3.8.1-15                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program 
ATTACHMENT 4 Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)
 
AC Sources - Operating B 3.8.1    SEQUOYAH - UNIT 1 B 3.8.1-16 Revision XX BASES  SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8). Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref.
9).
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable.
The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating. The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages. The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
SR  3.8.1.1  This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained. 


AC Sources - Operating B 3.8.1 BASES SURVEILLANCE    The AC sources are designed to permit inspection and testing of all REQUIREMENTS    important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).
Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.
The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.
The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 1                      B 3.8.1-16                                Revision XX


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 1 B 3.8.1-17 Revision XX BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2. SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governor's accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used.
During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governors accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
AC Sources - Operating B 3.8.1    SEQUOYAH - UNIT 1 B 3.8.1-21 Revision XX BASES  SURVEILLANCE REQUIREMENTS  (continued)
SEQUOYAH - UNIT 1                       B 3.8.1-17                              Revision XX
SR  3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single l oad (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post
-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post
-accident load with the DG solely supplying the board. Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.


AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post-accident load with the DG solely supplying the board.
Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.
The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than  0.89.
These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to  0.89 results in voltages on the emergency boards that are too high.
SEQUOYAH - UNIT 1                        B 3.8.1-21                              Revision XX


This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows  0.89. These conditions occur when grid voltage is high, and the additional field excitati 0.89 results in voltages on the emergency boards that are too high.
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE     The AC sources are designed to permit inspection and testing of all REQUIREMENTS     important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).
AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-16 Revision XX BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8). Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref.
Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).
9). Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating. The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages. The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.
 
The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 2                      B 3.8.1-16                                Revision XX


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-17 Revision XX BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
 
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2. SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governor's accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used.
During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governors accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 2                      B 3.8.1-17                              Revision XX


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-21 Revision XX BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post-accident load with the DG solely supplying the board.
: b. Tripping its associated single largest post
Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
-accident load with the DG solely supplying the board. Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.
 
The time a nd voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than  0.89.
These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to  0.89 results in voltages on the emergency boards that are too high.
SEQUOYAH - UNIT 2                        B 3.8.1-21                              Revision XX


This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows  0.89. These conditions occur when grid voltage is high, and the additional field
Tennessee Valley Authority, 1101 Market Street, Chattanooga, Tennessee 37402 CNL-16-001 May 26, 2016 10 CFR 50.90 U.S. Nuclear Regulatory Commission ATTN: Document Control Desk Washington, D.C. 20555-0001 Sequoyah Nuclear Plant Units 1 and 2 Renewed Facility Operating License Nos. DPR-77 and DPR-79 NRC Docket Nos. 50-327 and 50-328
 
e 0.89 results in voltages on the emergency boards that are too high.
 
Tennessee Valley Authority, 1101 Market Street, Chattanooga, Tennessee 37402 CNL-16-001 May 26, 2016  
 
10 CFR 50.90 U.S. Nuclear Regulatory Commission ATTN: Document Control Desk Washington, D.C. 20555-0001  
 
Sequoyah Nuclear Plant Units 1 and 2   Renewed Facility Operating License Nos. DPR-77 and DPR-79 NRC Docket Nos. 50-327 and 50-328  


==Subject:==
==Subject:==
Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)
Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)
In accordance with the provisions of Title 10 of the Code of Federal Regulations (10 CFR) 50.90, "Application for amendment of license, construction permit, or early site permit,"
In accordance with the provisions of Title 10 of the Code of Federal Regulations (10 CFR) 50.90, "Application for amendment of license, construction permit, or early site permit,"
Tennessee Valley Authority (TVA) is submitting a request for an amendment (SQN-TS-14-02) to Renewed Facility Operating License Nos. DPR-77 and DPR-79 for the Sequoyah Nuclear Plant (SQN) Units 1 and 2.  
Tennessee Valley Authority (TVA) is submitting a request for an amendment (SQN-TS-14-02) to Renewed Facility Operating License Nos. DPR-77 and DPR-79 for the Sequoyah Nuclear Plant (SQN) Units 1 and 2.
 
This license amendment request proposes to amend the SQN Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. Currently, the acceptance criteria are 58.8 Hz and  61.2 Hz. TVA proposes to change the SQN DG steady state frequency acceptance criteria to  59.8 Hz and  60.2 Hz. The DG TS SR steady state voltage range of  6800 V and  7260 V is unaffected.
This license amendment request proposes to amend the SQN Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. Currently, the acceptance criteria are 58.8 Hz and  61.2 Hz. TVA proposes to change the SQN DG steady state frequency acceptance criteria to  59.8 Hz and  60.2 Hz. The DG TS SR steady state voltage range of  6800 V and  7260 V is unaffected.
TVA has determined that the steady state frequency range acceptance criteria currently specified by SQN TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are non-conservative. A Condition Report (CR) was initiated in accordance with the TVA Corrective Action Program. Subsequently, a prompt determination of operability (PDO),
TVA has determined that the steady state frequency range acceptance criteria currently specified by SQN TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are non-conservative. A Condition Report (CR) was initiated in accordance with the TVA Corrective Action Program. Subsequently, a prompt determination of operability (PDO),
including administrative controls were established in accordance with the Nuclear Regulatory Commission (NRC) Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998. As a result of the CR, a number of immediate/interim and other corrective actions were identified, implemented, and completed. A review of historical DG test records for frequency and voltage supported the fact that the DGs were operable and supported the existing design basis analyses accidents. Administrative controls for DG frequency have been implemented in the applicable Surveillance Instructions to support continued DG operability.    
including administrative controls were established in accordance with the Nuclear Regulatory Commission (NRC) Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998. As a result of the CR, a number of immediate/interim and other corrective actions were identified, implemented, and completed. A review of historical DG test records for frequency and voltage supported the fact that the DGs were operable and supported the existing design basis analyses accidents. Administrative controls for DG frequency have been implemented in the applicable Surveillance Instructions to support continued DG operability.


U.S. Nuclear Regulatory Commission CNL-16-001  
U.S. Nuclear Regulatory Commission CNL-16-001 Page 2 May 26, 2016 The enclosure to this letter provides a description of the proposed changes, technical evaluation of the proposed changes, regulatory evaluation, and a discussion of environmental considerations. Attachments 1 and 2 to the enclosure provide the existing TS and Bases pages marked-up to show the proposed changes. Attachments 3 and 4 to the enclosure provide the existing TS and Bases pages retyped to show the proposed changes. Changes to the existing TS Bases, are provided for information only and will be implemented under the Technical Specification Bases Control Program.
As noted in the enclosure, the modified SR 3.8.1.9 is normally performed during outages.
Therefore, TVA requests NRC approval of this proposed license amendment by May 2017 with implementation during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy the revised SR 3.8.1.9 prior to implementation of this proposed license amendment.
TVA has determined that there are no significant hazard considerations associated with the proposed change and that the change qualifies for a categorical exclusion from environmental review pursuant to the provisions of 10 CFR 51 .22(c)(9).
The SQN Plant Operations Review Committee and the TVA Nuclear Safety Review Board have reviewed this proposed change and determined that operation of SQN Units 1 and 2 in accordance with the proposed change will not endanger the health and safety of the public.
In accordance with 10 CFR 50.91(b)(1), TVA is sending a copy of this letter and the enclosure to the Tennessee Department of Environment and Conservation.
There are no new regulatory commitments associated with this submittal. Please address any questions regarding this request to Ed Schrull at (423) 751-3850.
I declare under penalty of perjury that the foregoing is true and correct. Executed on this 26th day of May 2016.
President, Nuclear Licensing Enclosure cc: See Page 3


Page 3 May 26, 2016  
U.S. Nuclear Regulatory Commission CNL-16-001 Page 3 May 26, 2016 RDW: EDS
 
RDW: EDS  


==Enclosure:==
==Enclosure:==
Evaluation of Proposed Change cc (Enclosure):
Evaluation of Proposed Change cc (Enclosure):
NRC Regional Administrator - Region II NRC Senior Resident Inspector - Sequoyah Nuclear Plant NRR Project Manager - Sequoyah Nuclear Plant Director, Division of Radiological Health - Tennessee State Department of Environment and Conservation  
NRC Regional Administrator - Region II NRC Senior Resident Inspector - Sequoyah Nuclear Plant NRR Project Manager - Sequoyah Nuclear Plant Director, Division of Radiological Health - Tennessee State Department of Environment and Conservation


CNL-16-001 E1 of 20 
ENCLOSURE TENNESSEE VALLEY AUTHORITY SEQUOYAH NUCLEAR PLANT UNITS 1 AND 2 EVALUATION OF PROPOSED CHANGE


==Subject:==
==Subject:==
1.0  
Application to Modify Sequoyah Nuclear Plant Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02) 1.0


==SUMMARY==
==SUMMARY==
DESCRIPTION 2.0 DETAILED DESCRIPTION 2.1   Proposed Change 2.2   Need for Proposed Changes
DESCRIPTION 2.0 DETAILED DESCRIPTION 2.1     Proposed Change 2.2     Need for Proposed Changes 2.3     Implementation
 
2.3   Implementation
 
==3.0 TECHNICAL EVALUATION==


3.1  System Description
==3.0  TECHNICAL EVALUATION==


3.2   Evaluation
3.1    System Description 3.2     Evaluation 3.3    Conclusion


3.3  Conclusion
==4.0  REGULATORY EVALUATION==


==4.0 REGULATORY EVALUATION==
4.1    Applicable Regulatory Requirements and Criteria 4.2    Precedent 4.3    Significant Hazards Consideration 4.4    Conclusion


4.1 Applicable Regulatory Requirements and Criteria  4.2 Precedent 4.3 Significant Hazards Consideration
==5.0  ENVIRONMENTAL CONSIDERATION==


4.4 Conclusion
==6.0 REFERENCES==
 
==5.0 ENVIRONMENTAL CONSIDERATION==
 
==6.0 REFERENCES==


ATTACHMENTS
ATTACHMENTS
: 1. Proposed TS Changes (Mark
: 1. Proposed TS Changes (Mark-Ups) for SQN Units 1 and 2
-Ups) for SQN Units 1 and 2
: 2. Proposed TS Bases Changes (Mark-Ups) for SQN Units 1 and 2 (For Information Only)
: 2. Proposed TS Bases Changes (Mark
-Ups) for SQN Units 1 and 2 (For Information Only)
: 3. Proposed TS Changes (Final Typed) for SQN Units 1 and 2
: 3. Proposed TS Changes (Final Typed) for SQN Units 1 and 2
: 4. Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)
: 4. Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)
CNL-16-001                              E1 of 20


ENCLOSURE   CNL-16-001 E2 of 20  The Tennessee Valley Authority (TVA) is requesting a license amendment to amend the Sequoyah Nuclear Plant (SQN) Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in SQN Units 1 and 2, TS 3.8.1, "AC Sources - Operating.
ENCLOSURE 1.0    
"  Specifically, the proposed change and supporting evaluation will modify the acceptance criteria for the DG steady state frequency range provided in SQN Units 1 and 2 TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. Currently, the DG SR steady state acceptance criteria are  . TVA proposes to change the SQN DG steady state frequency acceptance criteria to 59.8 Hz and 0.2 Hz. The DG TS SR steady state voltage range of  6800 V and 7260 V is not affected. This license amendment request (LAR) is similar to a Watts Bar Nuclear Plant (WBN) Unit 1 submittal (Reference 1), which was approved by the NRC in Reference 2.
This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs o f TS 3.8.1 to be performed
. However, no specific changes to SR 3.8.1.3 or TS 3.8.2 are required.
Currently, the acceptance criteria for DG steady state frequency specified in SQN Units 1 and 2, TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are z and 1.2 Hz. TVA proposes to conservatively narrow the DG 59.8 Hz and decreasing the current upper limit from the existing 1.2 Hz to  60.2 Hz in the SQN Units 1 and 2 TS 1 (i.e., SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18) and TS Bases 3.8.1. The proposed SQN Units 1 and 2 DG frequency and voltage steady state operating range s only apply to the steady state condition of DG operation, and are summarized below in Table 1.
9.8 Hz to 0.2 Hz 6800 V to 7260 V  This change is applicable to the surveillance s performed at 31 days, 18 month s, and ten year s when maintenance & test equipment (M&TE) is installed on the DG per the surveillance instructions.


==SUMMARY==
DESCRIPTION The Tennessee Valley Authority (TVA) is requesting a license amendment to amend the Sequoyah Nuclear Plant (SQN) Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in SQN Units 1 and 2, TS 3.8.1, "AC Sources - Operating. Specifically, the proposed change and supporting evaluation will modify the acceptance criteria for the DG steady state frequency range provided in SQN Units 1 and 2 TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18.
Currently, the DG SR steady state acceptance criteria are  58.8 Hz and  61.2 Hz.
TVA proposes to change the SQN DG steady state frequency acceptance criteria to 59.8 Hz and  60.2 Hz. The DG TS SR steady state voltage range of  6800 V and 7260 V is not affected. This license amendment request (LAR) is similar to a Watts Bar Nuclear Plant (WBN) Unit 1 submittal (Reference 1), which was approved by the NRC in Reference 2.
This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed.
However, no specific changes to SR 3.8.1.3 or TS 3.8.2 are required.
2.0    DETAILED DESCRIPTION 2.1    Proposed Changes Currently, the acceptance criteria for DG steady state frequency specified in SQN Units 1 and 2, TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are  58.8 Hz and  61.2 Hz. TVA proposes to conservatively narrow the DG frequency range by increasing the current DG frequency lower limit of  58.8 Hz to 59.8 Hz and decreasing the current upper limit from the existing  61.2 Hz to  60.2 Hz in the SQN Units 1 and 2 TS1 (i.e., SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18) and TS Bases 3.8.1. The proposed SQN Units 1 and 2 DG frequency and voltage steady state operating ranges only apply to the steady state condition of DG operation, and are summarized below in Table 1.
Table 1 Technical Specification DG Steady-State Operating Range Parameter                                      Range Frequency                              59.8 Hz to  60.2 Hz Voltage                                6800 V to  7260 V This change is applicable to the surveillances performed at 31 days, 18 months, and ten years when maintenance & test equipment (M&TE) is installed on the DG per the surveillance instructions.
1 Note: No change is required to SQN Units 1 and 2, TS SR 3.8.1.19 because that surveillance does not apply to steady state operation.
1 Note: No change is required to SQN Units 1 and 2, TS SR 3.8.1.19 because that surveillance does not apply to steady state operation.
CNL-16-001                                    E2 of 20
ENCLOSURE The DG voltage limits as described in the Technical Specifications are correct and do not require revision.
Attachments 1 and 2 to this enclosure provide the existing SQN Units 1 and 2 TS and Bases pages marked-up to show the proposed changes. Attachments 3 and 4 to this enclosure provide the clean typed TS and Bases pages with the proposed changes incorporated.
The proposed Bases changes are provided to the NRC for information only.
2.2  Need for Proposed Changes Plant safety analyses make specific assumptions regarding the emergency core cooling system (ECCS) flow to provide the core cooling function following any event that requires safety injection (SI) to mitigate the event. For the events that assume a loss of offsite power (LOOP), the DGs provide power to the ECCS pumps. Following a LOOP, each DG starts and ties to an engineered safety feature (ESF) board, and essential loads, including the ECCS pumps, are sequentially connected to the ESF board by individual timers for each load sequence. The calculated ECCS flow rates assume that the steady state DG frequency is 60 Hz (i.e., after the DG starting and loading transients).
Once the DG starting and loading sequences are complete, the DG governor maintains the frequency at 60 Hz within a specified tolerance, which is based on the governor manufacturer/model.
The ECCS flow provided by the ECCS pumps is affected by the pump speed, which in turn is a function of the DG frequency. Historically, the DG frequency tolerances associated with the governor were not considered in the development of the ECCS, containment spray system (CSS), and auxiliary feedwater (AFW) flow rates. The primary effect of changes in DG frequency on the ECCS safety functions is an increase or decrease in the speed of safety-related motors that are powered by the DG. The increase or decrease in the speed of the motors affects pump performance, motor operated valve (MOV) stroke times, cooling fan performance, and DG loading, among other factors.
The minimum and maximum frequency values of 58.8 Hz and 61.2 Hz in the SQN TS SRs are equal to +/- 2% of the 60 Hz nominal frequency (i.e., the TS specified plant specific transient range). However, the +/- 2% frequency tolerance is only applicable to DG starting and loading transients, and does not apply to steady state operation as discussed in Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies" (Reference 3).
Because the safety analyses did not consider the effects of operating at the extremes of the steady state frequency range specified in TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18, TVA has determined that the current SQN Units 1 and 2 TS SR acceptance criteria for steady state DG frequency are non-conservative. The non-conservative acceptance criteria were addressed within the TVA corrective action program (CAP) and administrative controls were established in accordance with NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety" (Reference 4). To address the non-conservative TS, CNL-16-001                                  E3 of 20
ENCLOSURE TVA is proposing a change to TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 to revise the DG SR steady state acceptance criteria to  59.8 Hz and  60.2 Hz.
The four SQN DGs are shared between SQN Units 1 and 2, as described in Section 3.1, and the SRs for all four DGs are specified in the SQN Units 1 and 2 TSs. Therefore, the proposed SR steady state frequency acceptance criteria of  59.8 Hz and  60.2 Hz would apply to all four DGs.
2.3  Implementation The TVA process governing the preparation and submittal of TS changes and LARs requires that the appropriate organizations (e.g., Operations, Training, Engineering, Maintenance, Chemistry, Radiation Protection, and Work Control) identify the documents that are affected by each proposed change to the TSs and Operating Licenses. Among the items that are considered are training, plant modifications, procedures, special implementation constraints, design documents, and surveillance instructions associated with TS SRs, Technical Requirements Manual, TS Bases, and the Updated Final Safety Analysis Report (UFSAR). The process requires that procedures and design document changes necessary to support TS Operability are approved prior to implementation of an NRC approved license amendment. The process also provides assurance that the remaining changes, if any, are scheduled and tracked for configuration control.
SR 3.8.1.9 requires verification that each DG can maintain acceptable frequency following a load rejection greater than or equal to the single largest post-accident load.
This SR includes verification that the DG can restore frequency within the allowable steady-state band within three seconds. SQN currently performs SR 3.8.1.9 concurrent with SR 3.8.1.10, which verifies that the DG can withstand a full load rejection (from a fully loaded condition). This approach is acceptable because the full load rejection of SR 3.8.1.10 as well as the single largest post-accident load requirement of SR 3.8.1.9 are performed. The current test methodology for both SR 3.8.1.9 and 3.8.1.10 requires the DG to initially be in parallel with offsite power to achieve the required power value.
When the DG is operating in parallel with offsite power for surveillance testing, the speed droop circuit in the DG speed governor is required to be in service (i.e., non-emergency /
droop test mode). The speed droop function is necessary to ensure stable and controllable load-sharing between the DG and offsite power. However, the speed droop results in a steady-state frequency greater than the nominal 60 Hz value following a load rejection. Historical data shows that DG frequency typically stabilizes at approximately 60.3 Hz following a single largest load rejection with speed droop in service. This final frequency value is acceptable under the current SR 3.8.1.9, but is outside the more stringent frequency criteria proposed in this LAR. These results are due to the surveillance test methodology (i.e., performing the load rejection with the speed droop circuit in service) rather than being an indication of a problem or malfunction in the DG speed governor.
CNL-16-001                                    E4 of 20


ENCLOSURE   CNL-16-001 E3 of 20  The DG voltage limits as described in the Technical Specification s are correct and do not require revision. Attachments 1 and 2 to this enclosure provide the existing SQN Units 1 and 2 TS and Bases pages marked
ENCLOSURE To successfully perform SR 3.8.1.9 with the more conservative frequency band proposed in this LAR, the test methodology must be modified to perform the load rejection with the DG in accident mode (emergency / isochronous mode) and isolated on the shutdown board (i.e., not initially in parallel with offsite power). In the accident mode, the DG speed governor uses a fixed speed reference corresponding to 60.0 Hz, which ensures that the frequency criteria of SR 3.8.1.9 can be met. This requires a revision to the surveillance test procedures to perform SR 3.8.1.9 in conjunction with SR 3.8.1.18 (shutdown board blackout testing). This change in methodology is beneficial because it more closely replicates the conditions under which the DGs may have to perform following a loss of offsite power. TVA has initiated action to ensure that the applicable surveillance testing procedures are revised to incorporate this change prior to the next unit refueling outage on each SQN unit. Because the modified SR 3.8.1.9 is normally performed during outages, TVA is requesting implementation of this proposed license amendment during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy revised SR 3.8.1.9 prior to implementation of this proposed license amendment.
-up to show the proposed changes.
Attachments 3 and 4 to this enclosure provide the clean typed TS and Bases pages with the proposed changes incorporated
. The proposed Bases changes are provided to the NRC for information only.
Plant safety analyses make specific assumptions regarding the emergency core cooling syst em (ECCS) flow to provide the core cooling function following any event that requires safety injection (SI) to mitigate the event.
For the events that assume a loss of offsite power (LOOP), the DGs provide power to the ECCS pumps.
Following a LOOP, each DG starts and ties to an engineered safety feature (ESF) board, and essential loads, including the ECCS pumps, are sequentially connected to the ESF board by individual timers for each load sequence. The calculated ECCS flow rates assume that the steady state DG frequency is 60 Hz (i.e., after the DG starting and loading transients). Once the DG starting and loading sequences are complete, the DG governor maintains the frequency at 60 Hz within a specified tolerance, which is based on the governor manufacturer/model. The ECCS flow provided by the ECCS pumps is affected by the pump speed, which in turn is a function of the DG frequency.
Historically, the DG frequency tolerances associated with the governor were not considered in the development of the ECCS, containment spray system (CSS), and auxiliary feedwater (AFW) flow rates. The primary effect of changes in DG frequency on the ECCS safety functions is an increase or decrease in the speed of safety
-related motors that are powered by the DG. The increase or decrease in the speed of the motors affects pump performance, motor operated valve (MOV) stroke times, cooling fan performance, and DG loading, among other factor s. The minimum and maximum frequency values of 58.8 Hz and 61.2 Hz in the SQN TS SRs are equal to +/-
2% of the 60 Hz nominal frequency (i.e., the TS specified plant specific transient range
). However, the +/-
2% frequency tolerance is only applicable to DG starting and loading transients, and does not apply to steady state operation as discussed in Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies" (Reference 3). Because the safety analyses did not consider the effects of operating at the extremes of the steady state frequency range specified in TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18, TVA has determined that the current SQN Units 1 and 2 TS SR acceptance criteria for steady state DG frequency are non
-conservative. The non-conservative acceptance criteria were addressed within the TVA corrective action program (CAP) and administrative controls were established in accordance with NRC Administrative Letter 98
-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety" (Reference 4). To address the non
-conservative TS, ENCLOSURE    CNL-16-001 E4 of 20  TVA is proposing a change to TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 to revise the DG SR steady state acceptance criteria to 9.8 Hz and 0.2 Hz. The four SQN DGs are shared between SQN Units 1 and 2, as described in Section 3.1, and the SR s for all four DGs are specified in the SQN Units 1 and 2 TS s. Therefore, the proposed SR steady state frequency acceptance criteria of 9.8 Hz and 0.2 Hz would apply to all four DGs. The TVA process governing the preparation and submittal of TS changes and L AR s requires that the appropriate organizations (e.g., Operations, Training, Engineering, Maintenance, Chemistry, Radiation Protection, and Work Control) identify the documents that are affected by each proposed change to the TSs and Operating Licenses. Among the items that are considered are training, plant modifications, procedures, special implementation constraints, design documents, and surveillance instructions associated with TS SRs, Technical Requirements Manual, TS Bases, and the Updated Final Safety Analysis Report (UFSAR). The process requires that procedures and design document changes necessary to support TS Operability are approved prior to implementation of an NRC approved license amendment. The process also provides assurance that the remaining changes, if any, are scheduled and tracked for configuration control.
SR 3.8.1.9 requires verification that each DG can maintain acceptable frequency following a load rejection greater than or equal to the single largest post
-accident load. This SR includes verification that the DG can restore frequency within the allowable steady-state band within three seconds. SQN currently performs SR 3.8.1.9 concurrent with SR 3.8.1.10, which verifies that the DG can withstand a full load rejection (from a fully loaded condition). This approach is acceptable because the full load rejection of


SR 3.8.1.10 as well as the "single largest post
==3.0   TECHNICAL EVALUATION==
-accident load" requirement of SR 3.8.1.9 are performed. The current test methodology for both SR 3.8.1.9 and 3.8.1.10 requires the DG to initially be in parallel with offsite power to achieve the required power value.
When the DG is operating in parallel with offsite power for surveillance testing, the speed droop circuit in the DG speed governor is required to be in service (i.e., non-emergency / droop test mode). The speed droop function is necessary to ensure stable and controllable load
-sharing between the DG and offsite power. However, the speed droop results in a steady
-state frequency greater than the nominal 60 Hz value following a load rejection. Historical data shows that DG frequency typically stabilizes at approximately 60.3 Hz following a single largest load rejection with speed droop in service. This final frequency value is acceptable under the current SR 3.8.1.9, but is outside the more stringent frequency criteria proposed in this LAR. These results are due to the surveillance test methodology (i.e., performing the load rejection with the speed droop circuit in service) rather than being an indication of a problem or malfunction in the DG speed governor.
ENCLOSURE    CNL-16-001 E5 of 20   To successfully perform SR 3.8.1.9 with the more conservative frequency band proposed in this LAR, the test methodology must be modified to perform the load rejection with the DG in accident mode (emergency /
isochronous mode) and isolated on the shutdown board (i.e., not initially in parallel with offsite power). In the accident mode, the DG speed governor uses a fixed speed reference corresponding to 60.0 Hz, which ensures that the frequency criteria of SR 3.8.1.9 can be met. This requires a revision to the surveillance test procedures to perform SR 3.8.1.9 in conjunction with SR 3.8.1.18 (shutdown board blackout testing
). This change in methodology is beneficial because it more closely replicates the conditions under which the DGs may have to perform following a loss of offsite power. TVA has initiated action to ensure that the applicable surveillance testing procedures are revised to incorporate this change prior to the next unit refueling outage on each SQN unit. Because the modified SR 3.8.1.9 is normally performed during outages, TVA is requesting implementation of this proposed license amendment during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy revised SR 3.8.1.9 prior to implementation of this proposed license amendment. The onsite Class 1E alternating current (AC) standby system is described in SQN UFSAR Section 8.3, "Onsite Power System." As noted in SQN UFSAR Section 8.3, the onsite AC power system is a Class 1E system, which consists of the standby AC power system and the 120 V vital AC system. The standby AC power system is a safety
-related system, which supplies power for energizing all AC
-powered electrical devices essential to safety. The safety function of the s tandby AC power system is to supply power to permit functioning of components and systems required to assure that: (1) fuel design limits and reactor coolant pressure boundary design conditions are not exceeded due to anticipated operational occurrences, and (2) the core is cooled and vital functions are maintained in the event of a postulated accident, subject to loss of the preferred power system and subject to any single failure in the standby power system.
Specifically, the standby AC power system includes:  four Class 1E DGs (designated 1A-A, 1B-B, 2A-A, and 2B-B)  four 6.9 kV shutdown boards and logic relay panels associated 6.9 kV/480 V transformers and 480 V shutdown boards motor control centers supplied by the 480 V shutdown boards The AC standby power system is divided into two redundant load groups (power trains). The 6.9 kV shutdown boards are arranged electrically into two power trains with two boards associated with each train and each unit.
The boards comprising train A are located in the SQN Uni t 1 side and those of train B are located in the SQN Unit 2 side. The train A boards are separated from the train B boards by a reinforced concrete block wall, which is a qualified fire barrier, extended to the ceiling. When the preferred (offsite) power system is not available, each shutdown board is energized from a separate standby DG.


ENCLOSURE    CNL-16-001 E6 of 20   A loss of voltage on the 6.9 kV shutdown board starts the associated DG and initiates logic that trips the supply feeder breakers, all 6.9 kV loads (except the 480 V shutdown board transformers), and the major 480 V loads. The bypass breaker for the 480 V shutdown board's current
3.1  System Description The onsite Class 1E alternating current (AC) standby system is described in SQN UFSAR Section 8.3, "Onsite Power System.
-limiting inductive reactor is also closed as part of this logic. When the DG has reached rated speed and voltage, the generator is automatically connected to the 6.9 kV shutdown board. This return of voltage to the 6.9 kV shutdown board initiates logic that connects the required loads in sequence. The standby (onsite) power system's automatic sequencing logic is designed to automatically connect the required loads in proper sequence should the logic receive an accident signal prior to, concurrent with, or following a loss of all nuclear unit and preferred (offsite) power.
As noted in SQN UFSAR Section 8.3, the onsite AC power system is a Class 1E system, which consists of the standby AC power system and the 120 V vital AC system. The standby AC power system is a safety-related system, which supplies power for energizing all AC-powered electrical devices essential to safety. The safety function of the standby AC power system is to supply power to permit functioning of components and systems required to assure that: (1) fuel design limits and reactor coolant pressure boundary design conditions are not exceeded due to anticipated operational occurrences, and (2) the core is cooled and vital functions are maintained in the event of a postulated accident, subject to loss of the preferred power system and subject to any single failure in the standby power system.
As noted in UFSAR Section 8.3.1.1 , there are two loading sequences: "One, which is applied in the absence of a safety injection signal (SIS), the 'non-accident condition,' and the other 'accident condition,' applied when an SIS (and containment spray actuation signal) is received coincident with a sustained loss of voltage on the 6.9 kV shutdown board.
Specifically, the standby AC power system includes:
A loss of offsite power coincident with an SIS is the design basis event; however, as noted in UFSAR Section 8.3.1.1, an SIS received during the course of a non
* four Class 1E DGs (designated 1A-A, 1B-B, 2A-A, and 2B-B)
-accident shutdown loading sequence would cause the actions described below.
* four 6.9 kV shutdown boards and logic relay panels
: 1. "Loads already sequentially connected that are not required for an accident will be disconnected (except fire pumps powered by the DG). 2. Loads already sequentially connected that are required for an accident will remain connected.
* associated 6.9 kV/480 V transformers and 480 V shutdown boards
* motor control centers supplied by the 480 V shutdown boards The AC standby power system is divided into two redundant load groups (power trains).
The 6.9 kV shutdown boards are arranged electrically into two power trains with two boards associated with each train and each unit. The boards comprising train A are located in the SQN Unit 1 side and those of train B are located in the SQN Unit 2 side.
The train A boards are separated from the train B boards by a reinforced concrete block wall, which is a qualified fire barrier, extended to the ceiling. When the preferred (offsite) power system is not available, each shutdown board is energized from a separate standby DG.
CNL-16-001                                     E5 of 20
 
ENCLOSURE A loss of voltage on the 6.9 kV shutdown board starts the associated DG and initiates logic that trips the supply feeder breakers, all 6.9 kV loads (except the 480 V shutdown board transformers), and the major 480 V loads. The bypass breaker for the 480 V shutdown boards current-limiting inductive reactor is also closed as part of this logic.
When the DG has reached rated speed and voltage, the generator is automatically connected to the 6.9 kV shutdown board. This return of voltage to the 6.9 kV shutdown board initiates logic that connects the required loads in sequence. The standby (onsite) power system's automatic sequencing logic is designed to automatically connect the required loads in proper sequence should the logic receive an accident signal prior to, concurrent with, or following a loss of all nuclear unit and preferred (offsite) power.
As noted in UFSAR Section 8.3.1.1, there are two loading sequences:
One, which is applied in the absence of a safety injection signal (SIS), the non-accident condition, and the other accident condition, applied when an SIS (and containment spray actuation signal) is received coincident with a sustained loss of voltage on the 6.9 kV shutdown board.
A loss of offsite power coincident with an SIS is the design basis event; however, as noted in UFSAR Section 8.3.1.1, an SIS received during the course of a non-accident shutdown loading sequence would cause the actions described below.
: 1. Loads already sequentially connected that are not required for an accident will be disconnected (except fire pumps powered by the DG).
: 2. Loads already sequentially connected that are required for an accident will remain connected.
: 3. Loads pending sequential loading that are not required for an accident will not be connected.
: 3. Loads pending sequential loading that are not required for an accident will not be connected.
: 4. Loads awaiting sequential loading that are required for an accident will have their sequential timers reset to time zero from which they will then be sequentially loaded.An SIS received in the absence of a sustained loss of voltage on a 6.9 kV shutdown board would start the DGs , but would not connect them to the shutdown boards.
: 4. Loads awaiting sequential loading that are required for an accident will have their sequential timers reset to time zero from which they will then be sequentially loaded.
Each DG consists of two 16
An SIS received in the absence of a sustained loss of voltage on a 6.9 kV shutdown board would start the DGs, but would not connect them to the shutdown boards.
-cylinder engines directly connected to a 6.9 kV generator. The continuous rating of each DG is 4400 kilowatt (kW) at 0.8 power factor, 6.9 kV , 3-phase, and 60 Hz. Each DG also has an additional rating of 4840 kW for 2 hours out of 24 hours. Ratings for the DGs satisfy the requirements of Regulatory Guide 1.9 as clarified in Section 4.1. The continuous service rating of each DG is 4400 kW with 10% overload permissible for up to 2 hours in any 24 hour period. The normal operating speed of the DGs is 900 rpm. The DGs use a tandem arrangement; that is, each DG consists of two diesel engines with a generator between them connected together to form a common shaft. The DGs are physically separated, electrically isolated from each other, and protected from the probable maximum flood.
Each DG consists of two 16-cylinder engines directly connected to a 6.9 kV generator.
The continuous rating of each DG is 4400 kilowatt (kW) at 0.8 power factor, 6.9 kV, 3-phase, and 60 Hz. Each DG also has an additional rating of 4840 kW for 2 hours out of 24 hours.
Ratings for the DGs satisfy the requirements of Regulatory Guide 1.9 as clarified in Section 4.1. The continuous service rating of each DG is 4400 kW with 10% overload permissible for up to 2 hours in any 24 hour period.
The normal operating speed of the DGs is 900 rpm. The DGs use a tandem arrangement; that is, each DG consists of two diesel engines with a generator between them connected together to form a common shaft. The DGs are physically separated, electrically isolated from each other, and protected from the probable maximum flood.
CNL-16-001                                  E6 of 20


ENCLOSURE   CNL-16-001 E7 of 20  The DGs are equipped with Woodward governors and consist of:
ENCLOSURE The DGs are equipped with Woodward governors and consist of:
an E GB-13P actuator on each engine a 2301A computer (reverse biased) a magnetic speed pickup The Woodward EGB-13P actuator used with the 2301A computer is a proportional governor that moves the fuel rack in inverse proportion to the voltage signal from the computer. There is a governor actuator on each DG engine and they are electrically connected in series so that the loss of signal to one actuator would also result in the loss of signal to the other actuator. Based upon the input from the magnetic speed pickup, the electronic governor sends electric signals to the actuators on the two DG engines. This signal goes to the coils of each actuator that are connected in series so that each coil receives the same electric signal. The terminal shaft of each actuator will move the same amount for each change in signal, thus the fuel control shaft movement on each DG engine will be identical.
* an EGB-13P actuator on each engine
The steady state speed control will be within 0.25 percent of rated speed. The governor design includes circuits to provide high- and low-limit adjustments. These limits set the maximum and minimum speed that can be set by varying the speed
* a 2301A computer (reverse biased)
-setting milliamp or voltage reference. The low limit can be set as high as rated speed, if desired, eliminating the ability of the process or controller speed setting to reduce speed. The SQN Units 1 and 2 DG electrical governor is set within a speed band that is equivalent to a DG frequency of 59.95 Hz +/- 0.05 Hz. The SQN Units 1 and 2 DG voltage and frequency regulators were evaluated to ensure they were capable of meeting the TS and associated SRs. The measured values for both voltage and frequency have not exhibit ed drift and have been consistently within the respective setting band.
* a magnetic speed pickup The Woodward EGB-13P actuator used with the 2301A computer is a proportional governor that moves the fuel rack in inverse proportion to the voltage signal from the computer. There is a governor actuator on each DG engine and they are electrically connected in series so that the loss of signal to one actuator would also result in the loss of signal to the other actuator. Based upon the input from the magnetic speed pickup, the electronic governor sends electric signals to the actuators on the two DG engines.
This signal goes to the coils of each actuator that are connected in series so that each coil receives the same electric signal. The terminal shaft of each actuator will move the same amount for each change in signal, thus the fuel control shaft movement on each DG engine will be identical.
The steady state speed control will be within 0.25 percent of rated speed. The governor design includes circuits to provide high- and low-limit adjustments. These limits set the maximum and minimum speed that can be set by varying the speed-setting milliamp or voltage reference. The low limit can be set as high as rated speed, if desired, eliminating the ability of the process or controller speed setting to reduce speed. The SQN Units 1 and 2 DG electrical governor is set within a speed band that is equivalent to a DG frequency of 59.95 Hz +/- 0.05 Hz.
The SQN Units 1 and 2 DG voltage and frequency regulators were evaluated to ensure they were capable of meeting the TS and associated SRs. The measured values for both voltage and frequency have not exhibited drift and have been consistently within the respective setting band.
The SQN Units 1 and 2 DG voltage regulators and speed regulators are independent devices that are not expected to exhibit drift. This has been demonstrated by the past history of diesel surveillances in which the diesel is operated in isochronous mode. If the two variables drift in different directions (e.g., frequency lower and voltage higher), the combined effect on pump speed would be less than an individual drift.
The SQN Units 1 and 2 DG voltage regulators and speed regulators are independent devices that are not expected to exhibit drift. This has been demonstrated by the past history of diesel surveillances in which the diesel is operated in isochronous mode. If the two variables drift in different directions (e.g., frequency lower and voltage higher), the combined effect on pump speed would be less than an individual drift.
Based on this independence and stability, the composite impact of frequency and voltage were evaluated independently for the Technical Specification band. The frequency range was analyzed over the full range (i.e., 59.8 Hz to 60.2 Hz) within the voltage setting range (i.e., 6925 V to 7000 V). Likewise, the voltage (i.e., 6800 V to
Based on this independence and stability, the composite impact of frequency and voltage were evaluated independently for the Technical Specification band. The frequency range was analyzed over the full range (i.e., 59.8 Hz to 60.2 Hz) within the voltage setting range (i.e., 6925 V to 7000 V). Likewise, the voltage (i.e., 6800 V to 7260 V) was analyzed over the full range within the frequency range of 59.8 Hz to 60.2 Hz.
Test equipment verifies that the governor controls the DG frequency within the steady-state operational band of  59.8 Hz to  60.2 Hz.
The DGs, as clarified in Section 4.1, satisfy the requirements of Regulatory Guide (RG) 1.9, Revision 0 (Reference 3) and RG 1.9, Revision 1 (Reference 5).
CNL-16-001                                    E7 of 20


7260 V) was analyzed over the full range within the frequency range of 59.8 Hz to 60.2 Hz.
ENCLOSURE 3.2     Evaluation 3.2.1    Introduction Calculations were conducted to determine the effects of the DG frequency variation between 59.8 Hz and 60.2 Hz on plant equipment fed by the DGs following a loss of offsite power (LOOP) or a loss of coolant accident (LOCA) coincident with a LOOP.
Test equipment verifies that the governor controls the DG frequency within the steady
The changes in the DG frequency have the direct effect of changing motor speeds for the motors fed from the generators following a LOOP or a LOOP/LOCA. The changes in motor speeds are addressed in Section 3.2.2 and affect the following components:
-state operational band of 9.8 Hz to 0.2 Hz. The DGs, as clarified in Section 4.1, satisfy the requirements of Regulatory Guide (RG) 1.9, Revision 0 (Reference 3) and RG 1.9, Revision 1 (Reference 5).
* Pumps and Fans (Section 3.2.3)
ENCLOSURE   CNL-16-001 E8 of 20  Calculations were conducted to determine the effects of the DG frequency variation between 59.8 Hz and 60.2 Hz on plant equipment fed by the DGs following a loss of offsite power (LOOP) or a loss of coolant accident (LOCA) coincident with a LOOP. The changes in the DG frequency have the direct effect of changing motor speeds for the motors fed from the generators following a LOOP or a LOOP/LOCA. The changes in motor speeds are addressed in Section 3.2.2 and affect the following components:   Pump s and Fans (Section 3.2.3)   Air compressor s and chiller s (Section 3.2.4)   Motor operated valves (MOVs)
* Air compressors and chillers (Section 3.2.4)
(Section 3.2.5)   Electrical Equipment (Section 3.2.6) The changes in these parameters were evaluated to demonstrate that the subject equipment would continue to meet their safety related functions within the analyzed bounds documented in design documents. In addition, the increased horsepower associated with increased frequency was evaluated to ensure that the horsepower increases do not result in exceeding the sustained load ratings for the DGs and the decreased flowrate associated with the revised frequency range was evaluated to ensure pump parameters are adequate. Battery chargers and power transformers do not have motors, but frequency changes were examined to determine if the chargers and transformers would provide acceptable output parameters to continue to meet the specifications and requirements of the downstream components.
* Motor operated valves (MOVs) (Section 3.2.5)
The results of these calculations are provided below. Motor speed change, as a function of torque (Reference 6), is: S = (/N1)(SsynS) where, S = speed change Ssyn = motor synch speed S = motor speed
* Electrical Equipment (Section 3.2.6)
  = original torque N = the new torque The motor speed is directly affected by the frequency. T he affected component s , listed in Section 3.2.1, are either designed for 6600 V operation with the supply boards rated at 6900 V, or designed for 460 V operation with the supply boards rated ENCLOSURE    CNL-16-001 E9 of 20   at 480 V. Therefore, during normal operation, the motors see a voltage higher than their nominal rating. Thus, for the lower voltage limit of 6800 V (473 V on the low voltage side), the motors still have their minimum voltage and produce their design torque. Therefore, a low voltage condition is a non
The changes in these parameters were evaluated to demonstrate that the subject equipment would continue to meet their safety related functions within the analyzed bounds documented in design documents. In addition, the increased horsepower associated with increased frequency was evaluated to ensure that the horsepower increases do not result in exceeding the sustained load ratings for the DGs and the decreased flowrate associated with the revised frequency range was evaluated to ensure pump parameters are adequate. Battery chargers and power transformers do not have motors, but frequency changes were examined to determine if the chargers and transformers would provide acceptable output parameters to continue to meet the specifications and requirements of the downstream components.
-bounding condition and was not further evaluated.
The results of these calculations are provided below.
For the high voltage case, the motors could have a voltage of 7260 V (505 V on the low voltage side) or 10 percent above the motor design nominal rating , neglecting any voltage drop from the DG to the motor.
3.2.2    Comparison of Voltage and Frequency Impact Motor speed change, as a function of torque (Reference 6), is:
S = (/N1)(SsynS) where, S = speed change Ssyn = motor synch speed S = motor speed
          = original torque N = the new torque The motor speed is directly affected by the frequency. The affected components, listed in Section 3.2.1, are either designed for 6600 V operation with the supply boards rated at 6900 V, or designed for 460 V operation with the supply boards rated CNL-16-001                                   E8 of 20
 
ENCLOSURE at 480 V. Therefore, during normal operation, the motors see a voltage higher than their nominal rating. Thus, for the lower voltage limit of 6800 V (473 V on the low voltage side), the motors still have their minimum voltage and produce their design torque. Therefore, a low voltage condition is a non-bounding condition and was not further evaluated. For the high voltage case, the motors could have a voltage of 7260 V (505 V on the low voltage side) or 10 percent above the motor design nominal rating, neglecting any voltage drop from the DG to the motor.
Because the torque developed by a motor is directly proportional to the square of the terminal voltage, the above equation is rewritten in terms of voltage, as follows:
Because the torque developed by a motor is directly proportional to the square of the terminal voltage, the above equation is rewritten in terms of voltage, as follows:
 
S = [(V/VN)21]*(SsynS) where, S = speed change (SsynS) = motor slip, < 2 percent (the value of 2 percent is based on a review of vendor manuals which demonstrates that the motors have < 2 percent slip)
S = [(V/V N)21]*(SsynS) where, S = speed change (SsynS) = motor slip, < 2 percent (th e value of 2 percent is based on a review of vendor manuals which demonstrates that the motors have < 2 percent slip)
V = Nominal voltage, 6600 V VN = New voltage, 7260 V S = [(6600/7260)21]*(2 percent)
V = Nominal voltage, 6600 V V N = New voltage, 7260 V S = [(6600/7260) 2]*(2 percent)
S = -0.35 percent Thus, with a motor slip of less than 2 percent, the motor speed impact is less than 0.35 percent due to the voltage increase to 7260 V from design voltage of 6600 V.
S = -0.35 percent Thus, with a motor slip of less than 2 percent, the motor speed impact is less than 0.35 percent due to the voltage increase to 7260 V from design voltage of 6600 V. The frequency shift could result in a + 0.35 percent motor speed and the voltage could result in +0.35 percent motor speed change.
The frequency shift could result in a + 0.35 percent motor speed and the voltage could result in +0.35 percent motor speed change. Therefore, a speed impact of
Therefore, a speed impact of
        + 0.35 percent was used as the DG frequency impact for analyzing the effect caused either by frequency or voltage variation on the affected components in the following sections.
+ 0.35 percent was used as the DG frequency impact for analyzing the effect caused either by frequency or voltage variation on the affected components in the following sections.
3.2.3    Effect on Pumps 3.2.3.1  Pump Net Positive Suction Head (NPSH)
The change in the DG frequency was evaluated for the effect on the NPSH available to the following emergency core cooling system (ECCS) pumps. These pumps are fed from the DGs; therefore, they could be affected by the variation in frequency of 59.8 Hz to 60.2 Hz:
The change in the DG frequency was evaluated for the effect on the NPSH available to the following emergency core cooling system (ECCS) pumps. These pumps are fed from the DGs; therefore, they could be affected by the variation in frequency of 59.8 Hz to 60.2 Hz:
Containment spray (CS)
* Containment spray (CS)
Safety injection (SI)
* Safety injection (SI)
Residual heat removal (RHR)
* Residual heat removal (RHR)
Centrifugal charging (CC)
* Centrifugal charging (CC)
An evaluation was performed to determine if the NPSH available (NPSHA) exceeds the NPSH required (NPSHR) for the RHR and the CS pumps while taking suction from the containment sump (recirculation mode). The evaluation also determined ENCLOSURE    CNL-16-001 E 10 of 20   the NPSH Margin for the CS, SI, RHR, and CC pumps during injection mode operation with suction taken from the refueling water storage tank (RWST). Only the injection mode is presented, as the injection mode has less NPSH margin than the recirculation mode.
An evaluation was performed to determine if the NPSH available (NPSHA) exceeds the NPSH required (NPSHR) for the RHR and the CS pumps while taking suction from the containment sump (recirculation mode). The evaluation also determined CNL-16-001                                 E9 of 20
DG frequency affects both the head and flow values based on the pump affinity laws as follows:
 
Q 2 = (N 2 N 1)*Q1            where, Q2 = Changed pump flow due to DG frequency variation Q1 = Nominal pump flow N2  = Changed pump speed due to DG frequency variation N 1  = Nominal pump speed
 
For the 59.8 Hz frequency, Q 2 = (59.8/60.0)*Q 1 = 0.997*Q1  For the 60.2 Hz frequency, Q 2 = (60.2/60.0)*Q 1 = 1.003*Q1  Therefore, a 0.2Hz change in DG frequency will change pump flow by + 0.33%.      The NPSHR for pumps increases as the speed and flowrate increase. The NPSHR is also affected by the increase in DG frequency as follows
:  NPSHR 2 = (N 22)4/3*NPSHR 1                  (N 11)4/3    Table 2 presents examples of NPSHR changes resulting from the DG frequency changes for the various pumps.
The results in Table 3 demonstrate the actual flow rates, NPSHA, NPSHR, and the NPSH Margin for the various pumps. The NPSHR values were obtained from the pump manufacturer's NPSH curves at the flow values that are listed in Table 3. The DG increased frequency effects are included in these values. The results demonstrate that there is adequate positive margin for the pumps with the DG operating at the proposed revised frequencies.


ENCLOSURE   CNL-16-001 E 11 of 20  NPSHR (ft) current12.522 37.516NPSHR (ft) at 60.2 Hz12.622.1 37.816.1 Increased Pump Flow (sgpm)5100 5100 450 450 500 500 4200 4200 Pump Suction P (psig) 3.8 -2.5 6.7 6.8 1.9 1.6 -1.6 -3.9 Pump Suction P (psia) 18.2 11.9 21.1 21.2 16.3 16.0 12.8 10.5 Vapor P at 105&deg;F (psia) 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 NPSHA (psi) 17.1 10.8 20 20.1 15.2 14.9 11.7 9.4 NPSHA (ft) 39.7 25.1 46.5 46.7 35.3 34.6 27.2 21.8 NPSHR (ft) 12.1 12.1 18 18 19 19 15 15 NPSH margin (ft) 27.6 13 28.5 28.7 16.3 15.6 12.2 6.8    The DG frequency variation of 59.8 Hz to 60.2 Hz has a negligible effect on plant operations for the above affected pumps based on the revised flow rates in Section 3.2.3.1. The flow change resulting from the DG frequency variation is limited to + 0.3 5%. The pump test acceptance criteria upper limit will be adjusted downward, and the lower limit will be adjusted upward in order to encompass the potential flow variation. The ASME OM Code inservice pump testing acceptance criteria provide assurance that the design basis is met.
ENCLOSURE the NPSH Margin for the CS, SI, RHR, and CC pumps during injection mode operation with suction taken from the refueling water storage tank (RWST). Only the injection mode is presented, as the injection mode has less NPSH margin than the recirculation mode.
DG frequencies above/below 60 Hz directly increase/reduce motor speeds for fans. Fan speed is directly proportional to fan flow. Therefore, increased/reduced motor speed will result in increased/reduced flows.
3.2.3.1.1 Pump Flow Rates DG frequency affects both the head and flow values based on the pump affinity laws as follows:
For the 60.2 Hz DG frequency, fan flows are impacted as follows:
Q2 = (N2IN1)*Q1 where, Q2 = Changed pump flow due to DG frequency variation Q1 = Nominal pump flow N2 = Changed pump speed due to DG frequency variation N1 = Nominal pump speed For the 59.8 Hz frequency, Q2 = (59.8/60.0)*Q1 = 0.997*Q1 For the 60.2 Hz frequency, Q2 = (60.2/60.0)*Q1 = 1.003*Q1 Therefore, a 0.2Hz change in DG frequency will change pump flow by + 0.33%.
3.2.3.1.2 NPSH The NPSHR for pumps increases as the speed and flowrate increase. The NPSHR is also affected by the increase in DG frequency as follows:
NPSHR2 = (N2Q2)4/3*NPSHR1 (N1Q1)4/3 Table 2 presents examples of NPSHR changes resulting from the DG frequency changes for the various pumps.
The results in Table 3 demonstrate the actual flow rates, NPSHA, NPSHR, and the NPSH Margin for the various pumps. The NPSHR values were obtained from the pump manufacturers NPSH curves at the flow values that are listed in Table 3. The DG increased frequency effects are included in these values. The results demonstrate that there is adequate positive margin for the pumps with the DG operating at the proposed revised frequencies.
CNL-16-001                                  E10 of 20


ENCLOSURE    CNL-16-001 E 12 of 20   Q 2 = (60.2/60.0)*Q 1 = 1.0033*Q1 and for the 59.8 Hz DG frequency, fan flows are impacted as follows; Q 2 = (59.8/60.0)*Q1 = 0.9967*Q1 where: Q 2 = Changed fan flow due to DG frequency variation Q 1 = Nominal fan flow From the above equations, fan flow could vary from nominal to about +0.3 3%. From the G-Spec (Reference 7), total airflow of a system can vary by
ENCLOSURE Table 2 Example NPSHR Changes System                    CS              CC              SI            RHR NPSHR (ft) current            12.5              22            37.5            16 NPSHR (ft) at                  12.6            22.1          37.8            16.1 60.2 Hz Table 3 NPSH Margin While Operating in RWST Injection Mode with Revised DG Frequency System                    CS              CC            SI            RHR Pump Number            A-A      B-B   A-A B-B        A-A      B-B    A-A      B-B Increased Pump            5100      5100    450    450    500    500    4200      4200 Flow (sgpm)
+10% at the system fan. Thus, fan flows are within allowed tolerances due to sustained DG frequency variations
Pump Suction P              3.8      -2.5    6.7      6.8   1.9      1.6    -1.6    -3.9 (psig)
. Horsepower requirements for a pump motor and fan increase by the cube of the speed change. Therefore, increased motor speed will result in increased horsepower demands on the diesels that feed the subject loads. The potential increase in load on the DGs due to operating frequency and voltage was evaluated to 60.2 Hz and 7260 V. The highest steady state loading was used which envelopes the other steady state loading scenarios.
Pump Suction P            18.2     11.9  21.1    21.2 16.3    16.0   12.8    10.5 (psia)
Motor slip is defined as the difference between actual speed and synchronous speed
Vapor P at 105&deg;F            1.1      1.1    1.1      1.1  1.1      1.1    1.1       1.1 (psia)
 
NPSHA (psi)                17.1      10.8     20    20.1  15.2     14.9    11.7      9.4 NPSHA (ft)                39.7      25.1  46.5    46.7  35.3    34.6    27.2    21.8 NPSHR (ft)                12.1      12.1    18      18    19      19      15      15 NPSH margin (ft)           27.6      13    28.5    28.7  16.3    15.6    12.2      6.8 3.2.3.2     Pump Test Points The DG frequency variation of 59.8 Hz to 60.2 Hz has a negligible effect on plant operations for the above affected pumps based on the revised flow rates in Section 3.2.3.1. The flow change resulting from the DG frequency variation is limited to + 0.35%. The pump test acceptance criteria upper limit will be adjusted downward, and the lower limit will be adjusted upward in order to encompass the potential flow variation. The ASME OM Code inservice pump testing acceptance criteria provide assurance that the design basis is met.
an induction machine operates at as a percentage of the synchronous speed. A motor slip of about one percent increase in speed was calculated based on the increased DG voltage.
3.2.3.3    Effect on Fans DG frequencies above/below 60 Hz directly increase/reduce motor speeds for fans.
Fan speed is directly proportional to fan flow. Therefore, increased/reduced motor speed will result in increased/reduced flows. For the 60.2 Hz DG frequency, fan flows are impacted as follows:
CNL-16-001                                    E11 of 20


ENCLOSURE Q2 = (60.2/60.0)*Q1 = 1.0033*Q1 and for the 59.8 Hz DG frequency, fan flows are impacted as follows; Q2 = (59.8/60.0)*Q1 = 0.9967*Q1 where:
Q2 = Changed fan flow due to DG frequency variation Q1 = Nominal fan flow From the above equations, fan flow could vary from nominal to about +0.33%. From the G-Spec (Reference 7), total airflow of a system can vary by +10% at the system fan. Thus, fan flows are within allowed tolerances due to sustained DG frequency variations.
3.2.3.4  Effect on Horsepower Requirements Horsepower requirements for a pump motor and fan increase by the cube of the speed change. Therefore, increased motor speed will result in increased horsepower demands on the diesels that feed the subject loads. The potential increase in load on the DGs due to operating frequency and voltage was evaluated to 60.2 Hz and 7260 V. The highest steady state loading was used which envelopes the other steady state loading scenarios.
Motor slip is defined as the difference between actual speed and synchronous speed an induction machine operates at as a percentage of the synchronous speed. A motor slip of about one percent increase in speed was calculated based on the increased DG voltage.
Motor speed varies directly with the system frequency as shown below:
Motor speed varies directly with the system frequency as shown below:
1/2 = 1/ 2    Thus, the speed impact of the frequency variation is (60 + 0.2)/60 or + 0.33%. Therefore, the total impact of the voltage and frequency shift would be the sum of 1% + 0.33% which equals a 1.33% increase in motor speed.
1/2 = f1/f2 Thus, the speed impact of the frequency variation is (60 + 0.2)/60 or + 0.33%.
Therefore, the total impact of the voltage and frequency shift would be the sum of 1% + 0.33% which equals a 1.33% increase in motor speed.
As noted above, motor horsepower varies directly with the cube of the motor speed:
As noted above, motor horsepower varies directly with the cube of the motor speed:
LoadNew = Loadold Speed 3  LoadNew = LoadOld
LoadNew = Loadold *Speed3 LoadNew = LoadOld
* 1.0133 3  = LoadOld *1.040 Therefore, DG load would be increased by 4% if both the voltage and frequency were at their upper limits of 7260 V and 60.2 Hz
* 1.01333 = LoadOld *1.040 Therefore, DG load would be increased by 4% if both the voltage and frequency were at their upper limits of 7260 V and 60.2 Hz. Because the DG fuel oil consumption is analyzed for a fully loaded diesel, the voltage and frequency variation do not adversely affect the fuel oil analysis.
. Because the DG fuel oil consumption is analyzed for a fully loaded diesel, the voltage and frequency variation do not adversely affect the fuel oil analysis.
CNL-16-001                                E12 of 20


ENCLOSURE    CNL-16-001 E 13 of 20    Air compressors and chillers are intermittently operated equipment designed to maintain an asset or volume between selected setpoints. Air compressors cycle on to charge a system to a high pressure setpoint, and then cycle off until the header pressure drops below the specified setpoint. Chillers cycle on and off to maintain a refrigerant fluid temperature between a specified range of temperatures. Because both air compressors and chillers work intermittently to maintain a fluid media in a range between two setpoints, the approximate  
ENCLOSURE 3.2.4   Effect on Air Compressors and Chillers Air compressors and chillers are intermittently operated equipment designed to maintain an asset or volume between selected setpoints. Air compressors cycle on to charge a system to a high pressure setpoint, and then cycle off until the header pressure drops below the specified setpoint. Chillers cycle on and off to maintain a refrigerant fluid temperature between a specified range of temperatures. Because both air compressors and chillers work intermittently to maintain a fluid media in a range between two setpoints, the approximate +0.33% (+0.2 Hz) variation in DG frequency has a negligible effect on this type of equipment.
+0.3 3% (+0.2 Hz) variation in DG frequency has a negligible effect on this type of equipment.
3.2.5    Effect on MOVs The affected MOVs were evaluated for frequency and voltage related to DG loading.
 
The affected MOVs were evaluated for frequency and voltage related to DG loading.
Motor torque and stroke time are two important parameters associated with MOV performance. The DG frequency affects the motor torque (Section 3.2.2) and speed.
Motor torque and stroke time are two important parameters associated with MOV performance. The DG frequency affects the motor torque (Section 3.2.2) and speed.
Valve stroke time is inversely proportional to motor speed. Therefore, faster/slower motor speed would result in shorter/longer valve stroke times. For the 60.2 Hz frequency, valve stroke times vary as follows:
Valve stroke time is inversely proportional to motor speed. Therefore, faster/slower motor speed would result in shorter/longer valve stroke times. For the 60.2 Hz frequency, valve stroke times vary as follows:
T 2 = (60.2/60
T2 = (60.2/60.0)*T1 = 1.0033*T1                                          Equation (1) and for the 59.8 to 60.0 Hz DG frequency range, valve stroke times are affected as follows; T2 = (59.8/60.0)*T1 = 0.9967*T1                                          Equation (2) where:
.0)*T 1 = 1.00 33*T 1     Equation (1)
T2 = Changed stroke time due to DG frequency variation T1 = Nominal stroke time From equations (1) and (2), valve stroke times vary from nominal to approximately
        +0.33%. For example, a valve that strokes in 30 seconds has the potential variation in stroke time of approximately +0.1 seconds. This potential variation is small in comparison to the valve stroke times documented in the inservice testing program and is essentially the same as the recorded resolution of the stop watches used for valve stroke time testing (i.e., 0.1 seconds). The majority of the active safety related MOVs stroke in 10 seconds or less; therefore, the variance in stroke time is
        + 0.03 seconds. For a 10-second valve, this is below the detectible threshold of the normal timing method. The longest of the safety related valve stroke times is up to 120 seconds for the valves involved in the automatic containment sump swap over.
The time variation is about + 0.4 seconds for these valves.
The MOV stroke time acceptance criteria for the ASME OM Code testing are adjusted to include the potential low frequency power. Accordingly, the design basis requirements for valve stroke time will be met. The minimum allowable DG voltage provides a voltage that is greater than the voltage used for the Generic Letter 89-10 analysis.
CNL-16-001                                  E13 of 20


and for the 59.8 to 60.0 Hz DG frequency range, valve stroke times are affected as follows; T 2 = (59.8/60.0)*T 1 = 0.99 67*T 1      Equation (2) where:  T 2 = Changed stroke time due to DG frequency variation T 1 = Nominal stroke time From equations (1) and (2), valve stroke times vary from nominal to approximately
ENCLOSURE Furthermore, based on the analyses in Section 3.2.2, the impact to torque is acceptable. In addition, there would not be a concern for water hammer due to the small change in stroke time. Therefore, there are no concerns with MOV operation due to the variation in DG frequency and voltage.
+0.3 3%. For example, a valve that strokes in 30 seconds has the potential variation in stroke time of approximately
3.2.6    Effect on Electrical Equipment Most static loads are insensitive to changes in frequency and have a directly proportional change in current with terminal voltage, which is the opposite of the effects of voltage variation on induction motors. Only electronically controlled equipment, such as battery chargers, inverters and uninterruptible power supplies may be of concern at off nominal line frequency. The maximum allowable board voltage is 7260 V and the degraded voltage relay safety limit dropout setting is 6400 V. The variation in voltage from the DG of 6800 to 7260 V is much less than the range expected from the offsite source. Therefore, the variation in DG output voltage is bounded by voltage variations when off site power supplies the AC auxiliary power system.
+0.1 seconds. This potential variation is small in comparison to the valve stroke times documented in the inservice testing program and is essentially the same as the recorded resolution of the stop watches used for valve stroke time testing (i.e., 0.1 seconds). The majority of the active safety related MOVs stroke in 1 0 seconds or less; therefore, the variance in stroke time is + 0.03 seconds. For a 10-second valve, this is below the detectible threshold of the normal timing method. The longest of the safety related valve stroke times is up to 120 seconds for the valves involved in the automatic containment sump swap over. The time variation is about + 0.4 seconds for these valves.  
3.2.6.1  Battery Chargers The battery charger regulation is maintained at +/-1% from no-load to full load with simultaneous changes in AC line voltage of +10% / -15% and changes in AC line frequency of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the battery chargers.
3.2.6.2  Hydrogen Igniters The hydrogen mitigation system (i.e., H2 igniters) does not use frequency sensitive components with the exception of the regulating transformer. The output is regulated to +/-1% from no-load to full load with AC line voltage changes of +/-10% and changes in AC frequency changes of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the hydrogen mitigation system.
3.2.6.3  Instrumentation 120 V AC instrumentation circuits are designed with a +/-1% variation in frequency.
The variation in DG frequency is within this range.
3.3      Conclusion The results of these calculations determined that the proposed change in the DG frequency does not adversely affect the equipment powered by the DGs and their associated components described above. The calculations are available for NRC review. The DG output voltage and frequency range of 6800 to 7260 V and 59.8 to 60.2 Hz, respectively, will not affect the miscellaneous electrical equipment required to mitigate design basis events.
CNL-16-001                                  E14 of 20


The MOV stroke time acceptance criteria for the ASME OM Code testing are adjusted to include the potential low frequency power. Accordingly, the design basis requirements for valve stroke time will be met.
ENCLOSURE
The minimum allowable DG voltage provides a voltage that is greater than the voltage used for the Generic Letter 89-10 analysis.
ENCLOSURE   CNL-16-001 E 14 of 20    Furthermore, based on the analyses in Section 3.2.2, the impact to torque is acceptable. In addition, there would not be a concern for water hammer due to the small change in stroke time.
Therefore, there are no concerns with MOV operation due to the variation in DG frequency and voltage.
Most static loads are insensitive to changes in frequency and have a directly proportional change in current with terminal voltage, which is the opposite of the effects of voltage variation on induction motors. Only electronically controlled equipment, such as battery chargers, inverters and uninterruptible power supplies may be of concern at off nominal line frequency. The maximum allowable board voltage is 7260 V and the degraded voltage relay safety limit dropout setting is 6400 V. The variation in voltage from the DG of 6800 to 7260 V is much less than the range expected from the offsite source. Therefore, the variation in DG output voltage is bounded by voltage variations when off site power supplies the AC auxiliary power system.
The battery charger regulation is maintained at +/-1% from no
-load to full load with simultaneous changes in AC line voltage of +10% /
-15% and changes in AC line frequency of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the battery chargers. The hydrogen mitigation system (i.e., H 2 igniters) does not use frequency sensitive components with the exception of the regulating transformer. The output is regulated to +/-1% from no
-load to full load with AC line voltage changes of +/-10% and changes in AC frequency changes of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the hydrogen mitigation system.


120 V AC instrumentation circuits are designed with a +/-1% variation in frequency. The variation in DG frequency is within this range.
==4.0  REGULATORY EVALUATION==


The results of these calculations determined that the proposed change in the DG frequency does not adversely affect the equipment powered by the DGs and their associated components described above. The calculations are available for NRC review. The DG output voltage and frequency range of 6800 to 7260 V and 59.8 to 60.2 Hz, respectively, will not affect the miscellaneous electrical equipment required to mitigate design basis events. 
4.1  Applicable Regulatory Requirements and Criteria The onsite standby ac power systems at SQN Units 1 and 2 are designed to comply with the following applicable regulations and requirements.
* Title 10 of the Code of Federal Regulations (10 CFR) Part 50 (10 CFR 50),
Appendix A, General Design Criterion (GDC) 17, "Electric power systems," specifies that an onsite electric power system shall be provided to permit functioning of structures, systems, and components important to safety.
* 10 CFR 50, Appendix A, GDC 18, "Inspection and testing of electric power systems,"
specifies that electric power systems important to safety shall be designed to permit appropriate periodic inspection and testing of important areas and features.
* Regulatory Guide 1.6, Revision 0 (Reference 8), "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems," describes an acceptable degree of independence between redundant standby (onsite) power sources and between their distribution systems.
* Regulatory Guide 1.9, Revision 0 (Reference 3). As noted in SQN UFSAR Section 8.3.1.2.1, SQN Units 1 and 2 comply with Regulatory Guide 1.9, Revision 0 except that voltage and frequency recovery requirements are taken from Regulatory Guide 1.9, Revision 1. As further noted in SQN UFSAR Section 8.3.1.2.1, an exception is taken for frequency immediately following DG breaker closure. The DG breaker is designed to automatically close at about 94 percent of nominal frequency.
This exception was accepted by the NRC in NUREG-1232 Volume 2 (Reference 9).
* IEEE Standard 308-1971, "Criteria for Class 1E Power Systems for Nuclear Power Generating Stations," provides criteria for the determination of Class 1E power system design features and the requirements for their testing, surveillance, and documentation.
With the implementation of the proposed change, SQN Units 1 and 2 continues to meet the applicable regulations and requirements, subject to the previously approved exceptions.
4.2  Precedent The NRC has previously approved changes revising the TS SR acceptance criteria for steady state DG frequency.
: 1. Amendment Number 102 was issued for WBN Unit 1 in the Safety Evaluation dated September 17, 2015 (Reference 2). The Amendment made changes similar to those in this proposed license amendment request in that it revised the DG SR steady state frequency from  58.8 Hz and 61.2 Hz to 59.8 Hz and  60.1 Hz.
: 2. Amendment Numbers 227 and 105 were issued for Beaver Valley Power Station, Units 1 and 2, respectively, in the Safety Evaluation dated February 11, 2000 CNL-16-001                                  E15 of 20


ENCLOSURE   CNL-16-001 E 15 of 20  The onsite standby ac power systems at SQN Units 1 and 2 are designed to comply with the following applicable regulations and requirements. Title 10 of the Code of Federal Regulations (10 CFR) Part 50 (10 CFR 50), Appendix A, General Design Criterion (GDC) 17, "Electric power systems," specifies that an onsite electric power system shall be provided to permit functioning of structures, systems, and components important to safety.
ENCLOSURE (Reference 10). The Amendment corrected non-conservative TSs by clarifying the fuel oil storage volume requirements, increasing the load requirement for the single largest load rejection test, establishing criteria for maximum frequency that should not be exceeded following a load rejection, and revising the DG SR steady state frequency to  60.0 Hz and  60.6 Hz for Units 1 and 2 and 59.9 Hz and  60.3 Hz for Unit 2.
10 CFR 50, Appendix A, GDC 18, "Inspection and testing of electric power systems," specifies that electric power systems important to safety shall be designed to permit appropriate periodic inspection and testing of important areas and features.
: 3. Amendment Number 129 was issued for the Palo Verde Nuclear Generating Station, Units 1, 2, and 3, in the Safety Evaluation dated October 4, 2000 (Reference 11).
Regulatory Guide 1.6, Revision 0 (Reference 8), "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems," describes an acceptable degree of independence between redundant standby (onsite) power sources and between their distribution systems.
The Amendment corrected non-conservative TSs by revising the current steady-state DG voltage limits of  3740 V and  4580 V and steady state frequency limit of 59.7 Hz and  61.2 Hz to a steady state voltage of 4000 V and <4377.2 V, and steady state frequency of  59.7 Hz and  60.7 Hz for the affected SR, except that for SR 3.8.1.2, the lower frequency limit is  58.8 Hz instead of the  59.7 Hz.
Regulatory Guide 1.9, Revision 0 (Reference 3). As noted in SQN UFSAR Section 8.3.1.2.1, SQN Units 1 and 2 comply with Regulatory Guide 1.9, Revision 0 except that voltage and frequency recovery requirements are taken from Regulatory Guide 1.9, Revision 1. As further noted in SQN UFSAR Section 8.3.1.2.1, an exception is taken for frequency immediately following DG breaker closure. The DG breaker is designed to automatically close at about 94 percent of nominal frequency. This exception was accepted by the NRC in NUREG
: 4. Amendment Numbers 309 and 291 were issued for the Donald C. Cook Nuclear Plant, Units 1 and 2, respectively, in the Safety Evaluation dated April 30, 2009 (Reference 12). The Amendment corrected non-conservative TSs by reducing the maximum DG steady state frequency in the associated SRs from 61.2 Hz to 60.5 Hz.
-1232 Volume 2 (Reference 9). IEEE Standard 308
The Amendment also revised the minimum steady state voltage from 3740 V to 3910 V for certain TS SRs for consistency with the minimum steady state voltage specified in the acceptance criteria for other TS SRs, and reduced the criteria for maximum frequency that should not be exceeded following a load rejection.
-1971, "Criteria for Class 1E Power Systems for Nuclear Power Generating Stations," provides criteria for the determination of Class 1E power system design features and the requirements for their testing, surveillance, and documentation.
: 5. Amendment Number 236 was issued for Crystal River, Unit 3 in the Safety Evaluation dated December 10, 2009 (Reference 13). The Amendment corrected non-conservative TSs by revising the DG steady state voltage to 4077 V and 4243 V and DG steady state frequency to  59.4 Hz and 60.6 Hz.
: 6. Amendment 204 was issued for the Wolf Creek Generating Station in the Safety Evaluation dated April 11, 2013 (Reference 14). The Amendment corrected non-conservative TSs by revising minimum DG steady state voltage to 3950 V and DG steady state frequency to 59.4 Hz and 60.6 Hz. The Amendment also revised the DG loading requirements to reflect the results of updated calculations.
4.3  Significant Hazards Consideration The proposed change would modify the Sequoyah Nuclear Plant (SQN), Units 1 and 2, Technical Specification (TS) 3.8.1, "AC Sources - Operating," by revising the acceptance criteria for the diesel generator (DG) steady state frequency acceptance criteria specified in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. The frequency will be changed from  58.8 Hz and  61.2 Hz to 59.8 Hz and 60.2 Hz for SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18.
This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed.
CNL-16-001                                  E16 of 20


With the implementation of the proposed change, SQN Units 1 and 2 continues to meet the applicable regulations and requirements, subject to the previously approved exceptions.
ENCLOSURE TVA has evaluated whether or not a significant hazards consideration is involved with the proposed amendment(s) by focusing on the three standards set forth in 10 CFR 50.92, Issuance of amendment, as discussed below:
The NRC has previously approved changes revising the TS SR acceptance criteria for steady state DG frequency.
: 1.     Does the proposed amendment involve a significant increase in the probability or consequence of an accident previously evaluated?
: 1. Amendment Number 102 was issued for WBN Unit 1 in the Safety Evaluation dated September 17, 2015 (Reference 2). The Amendment made changes similar to those in this proposed license amendment request in that it revised the DG SR steady state frequency from 58.8 Hz and 61.2 Hz to  59.8 Hz and 60.1 Hz. 2. Amendment Numbers 227 and 105 were issued for Beaver Valley Power Station, Units 1 and 2, respectively, in the Safety Evaluation dated February 11, 2000 ENCLOSURE    CNL-16-001 E 16 of 20  (Reference 10). The Amendment corrected non
Response: No The DGs are required to be operable in the event of a design basis accident coincident with a loss of offsite power to mitigate the consequences of the accident. The DGs are not accident initiators and therefore these changes do not involve a significant increase in the probability of an accident previously evaluated.
-conservative TSs by clarifying the fuel oil storage volume requirements, increasing the load requirement for the single largest load rejection test, establishing criteria for maximum frequency that should not be exceeded following a load rejection, and revising the DG SR steady state frequency to  60.0 Hz and 0.6 Hz for Units 1 and 2 59.9  60.3 Hz for Unit 2.
: 3. Amendment Number 129 was issued for the Palo Verde Nuclear Generating Station, Units 1, 2, and 3, in the Safety Evaluation dated October 4, 2000 (Reference 11). The Amendment corrected non
-conservative TSs by revising the current steady
-state  3740 V  4580 V and steady state frequency limit of  59.7 Hz and 1.2 Hz to a steady s4000 V and <4377.2 V, and steady state frequency of 9.7 Hz and 0.7 Hz for the affected SR, except that for SR 3.8.1.2, the lower frequency limit is 8.8 Hz instead of the 9.7 Hz. 4. Amendment Numbers 309 and 291 were issued for the Donald C. Cook Nuclear Plant, Units 1 and 2, respectively, in the Safety Evaluation dated April 30, 2009 (Reference 12). The Amendment corrected non
-conservative TSs by reducing the maximum DG steady state frequency in the associated SRs from 61.2 Hz to 60.5 Hz. The Amendment also revised the minimum steady state voltage from 3740 V to  3910 V for certain TS SRs for consistency with the minimum steady state voltage specified in the acceptance criteria for other TS SRs, and reduced the criteria for maximum frequency that should not be exceeded following a load rejection
. 5. Amendment Number 236 was issued for Crystal River, Unit 3 in the Safety Evaluation dated December 10, 2009 (Reference 13). The Amendment corrected non-conservative TSs by V and  4243 V and DG steady state frequency to 9.4 Hz and 0.6 Hz. 6. Amendment 204 was issued for the Wolf Creek Generating Station in the Safety Evaluation dated April 11, 2013 (Reference 14). The Amendment corrected non-conservative TSs by revising minimum DG steady state voltage to 3950 V and DG steady state frequency to 9.4 Hz and 0.6 Hz. The Amendment also revised the DG loading requirements to reflect the results of updated calculations. The proposed change would modify the Sequoyah Nuclear Plant (SQN), Units 1 and 2, Technical Specification (TS) 3.8.
1 , "AC Sources - Operating," by revising the acceptance criteria for the diesel generator (DG) steady state frequency acceptance criteria specified in TS Surveillance Requirements (SR s) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.188.8 Hz and  61.2 Hz to 9.8 Hz and 0.2 Hz for SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed. 
 
ENCLOSURE   CNL-16-001 E 17 of 20  TVA has evaluated whether or not a significant hazards consideration is involved with the proposed amendment(s) by focusing on the three standards set forth in 10 CFR 50.92, "Issuance of amendment," as discussed below:
: 1. Does the proposed amendment involve a significant increase in the probability or consequence of an accident previously evaluated? Response: No The DGs are required to be operable in the event of a design basis accident coincident with a loss of offsite power to mitigate the consequences of the accident. The DGs are not accident initiators and therefore these changes do not involve a significant increase in the probability of an accident previously evaluated.
The accident analyses assume that at least the boards in one load group are provided with power either from the offsite circuits or the DGs. The change proposed in this license amendment request will continue to assure that the DGs have the capacity and capability to assume their maximum design basis accident loads. The proposed change does not significantly alter how the plant would mitigate an accident previously evaluated.
The accident analyses assume that at least the boards in one load group are provided with power either from the offsite circuits or the DGs. The change proposed in this license amendment request will continue to assure that the DGs have the capacity and capability to assume their maximum design basis accident loads. The proposed change does not significantly alter how the plant would mitigate an accident previously evaluated.
The proposed change does not adversely affect accident initiators or precursors nor alter the design assumptions, conditions, and configuration of the facility or the manner in which the plant is operated and maintained. The proposed change does not adversely affect the ability of structures, systems, and components (SSC) to perform their intended safety function to mitigate the consequences of an initiating event within the assumed acceptance limits. The proposed change does not affect the source term, containment isolation, or radiological release assumptions used in evaluating the radiological consequences of any accident previously evaluated.
The proposed change does not adversely affect accident initiators or precursors nor alter the design assumptions, conditions, and configuration of the facility or the manner in which the plant is operated and maintained. The proposed change does not adversely affect the ability of structures, systems, and components (SSC) to perform their intended safety function to mitigate the consequences of an initiating event within the assumed acceptance limits. The proposed change does not affect the source term, containment isolation, or radiological release assumptions used in evaluating the radiological consequences of any accident previously evaluated. Further, the proposed change does not increase the types and amounts of radioactive effluent that may be released offsite, nor significantly increase individual or cumulative occupational/public radiation exposure.
Further, the proposed change does not increase the types and amounts of radioactive effluent that may be released offsite, nor significantly increase individual or cumulative occupational/public radiation exposure.
Therefore, the proposed change does not involve a significant increase in the probability or consequences of an accident previously evaluated.
Therefore, the proposed change does not involve a significant increase in the probability or consequences of an accident previously evaluated.
2.Does the proposed amendment create the possibility of a new or different kind of accident from any accident previously evaluat ed? Response: No.
: 2.     Does the proposed amendment create the possibility of a new or different kind of accident from any accident previously evaluated?
The proposed change does not involve a change in the plant design, system operation, or the use of the DGs. The proposed change requires the DGs to meet SR acceptance criteria that envelope the actual demand requirements for the DGs during design basis conditions. These revised acceptance criteria continue to demonstrate the capability and capacity of the DGs to perform their required functions. There are no new failure modes or mechanisms created due to testing the DGs within the proposed acceptance criteria. Testing of the DGs at the proposed acceptance criteria does not involve any modification in the ENCLOSURE    CNL-16-001 E 18 of 20   operational limits or physical design of plant systems. There are no new accident precursors generated due to the proposed test loadings. Therefore, the proposed change does not create the possibility of a new or different kind of accident from any accident previously evaluated.
Response: No.
3.Does the proposed amendment involve a significant reduction in a margin of safety? Response: No. The proposed change will continue to demonstrate that the DGs meet the TS definition of operability, that is, the proposed acceptance criteria will continue to demonstrate that the DGs will perform their safety function. The proposed testing will also continue to demonstrate the capability and capacity of the DGs to supply their required loads for mitigating a design basis accident.
The proposed change does not involve a change in the plant design, system operation, or the use of the DGs. The proposed change requires the DGs to meet SR acceptance criteria that envelope the actual demand requirements for the DGs during design basis conditions. These revised acceptance criteria continue to demonstrate the capability and capacity of the DGs to perform their required functions. There are no new failure modes or mechanisms created due to testing the DGs within the proposed acceptance criteria. Testing of the DGs at the proposed acceptance criteria does not involve any modification in the CNL-16-001                                   E17 of 20
 
ENCLOSURE operational limits or physical design of plant systems. There are no new accident precursors generated due to the proposed test loadings.
Therefore, the proposed change does not create the possibility of a new or different kind of accident from any accident previously evaluated.
: 3.     Does the proposed amendment involve a significant reduction in a margin of safety?
Response: No.
The proposed change will continue to demonstrate that the DGs meet the TS definition of operability, that is, the proposed acceptance criteria will continue to demonstrate that the DGs will perform their safety function. The proposed testing will also continue to demonstrate the capability and capacity of the DGs to supply their required loads for mitigating a design basis accident.
The proposed change does not alter the manner in which safety limits, limiting safety system settings or limiting conditions for operation are determined. The safety analysis acceptance criteria are not affected by this change. The proposed change will not result in plant operation in a configuration outside the design basis.
The proposed change does not alter the manner in which safety limits, limiting safety system settings or limiting conditions for operation are determined. The safety analysis acceptance criteria are not affected by this change. The proposed change will not result in plant operation in a configuration outside the design basis.
Therefore, the proposed change does not involve a significant reduction in a margin of safety.
Therefore, the proposed change does not involve a significant reduction in a margin of safety.
Based on the above, TVA concludes that the proposed amendment does not involve a significant hazards consideration under the standards set forth in 10 CFR 50.92 (c), and, accordingly, a finding of "no significant hazards consideration" is justified.
Based on the above, TVA concludes that the proposed amendment does not involve a significant hazards consideration under the standards set forth in 10 CFR 50.92 (c), and, accordingly, a finding of no significant hazards consideration is justified.
In conclusion, based on the considerations discussed above, (1) there is reasonable assurance that the health and safety of the public will not be endangered by operation in the proposed manner, (2) such activities will be conducted in compliance with the Commission's regulations, and (3) the issuance of the amendment will not be inimical to the common defense and security or to the health and safety of the public.
4.4  Conclusion In conclusion, based on the considerations discussed above, (1) there is reasonable assurance that the health and safety of the public will not be endangered by operation in the proposed manner, (2) such activities will be conducted in compliance with the Commissions regulations, and (3) the issuance of the amendment will not be inimical to the common defense and security or to the health and safety of the public.
 
==5.0  ENVIRONMENTAL CONSIDERATION==
 
A review has determined that the proposed amendment would change a requirement with respect to installation or use of a facility component located within the restricted area, as defined in 10 CFR 20, or would change an inspection or surveillance requirement. However, the proposed amendment does not involve (i) a significant hazards consideration, (ii) a significant change in the types or significant increase in the amounts of any effluents that may be released offsite, or (iii) a significant increase in individual or cumulative occupational radiation exposure. Accordingly, the proposed amendment meets the eligibility criterion for categorical exclusion set forth in 10 CFR 51.22(c)(9). Therefore, pursuant to 10 CFR 51.22(b), no environmental impact statement or environmental assessment need be prepared in connection with the proposed amendment.
A review has determined that the proposed amendment would change a requirement with respect to installation or use of a facility component located within the restricted area, as defined in 10 CFR 20, or would change an inspection or surveillance requirement. However, the proposed amendment does not involve (i) a significant hazards consideration, (ii) a significant change in the types or significant increase in the amounts of any effluents that may be released offsite, or (iii) a significant increase in individual or cumulative occupational radiation exposure. Accordingly, the proposed amendment meets the eligibility criterion for categorical exclusion set forth in 10 CFR 51.22(c)(9). Therefore, pursuant to 10 CFR 51.22(b), no environmental impact statement or environmental assessment need be prepared in connection with the proposed amendment.
ENCLOSURE    CNL-16-001 E 19 of 20   1. TVA Letter to NRC, CNL 218, "Application to Modify Watts Bar Nuclear Plant, Unit 1 Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (SQN
CNL-16-001                                     E18 of 20
-TS-13-08)," dated April 6, 2015 (ML15117A462)
 
: 2. NRC letter to TVA, "Watts Bar Nuclear Plant, Unit 1 - Issuance of Amendment Regarding Modification To Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (TAC N
ENCLOSURE
: o. MF6153)," dated September 17, 2015 (ML15230A155)
: 3. Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for


Standby Power Supplies" 4. NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998
==6.0  REFERENCES==
: 5. Regulatory Guide 1.9, Revision 1, "Selection, Design, and Qualification of Diesel
: 1. TVA Letter to NRC, CNL-14-218, Application to Modify Watts Bar Nuclear Plant, Unit 1 Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (SQN-TS-13-08), dated April 6, 2015 (ML15117A462)
-Generator Units Used as Onsite Electric Power Systems at Nuclear Power Plants" 6. WCAP-17308-NP, Treatment of Diesel Generator (DG) Technical Specification Frequency and Voltage Tolerances, April 2012
: 2. NRC letter to TVA, Watts Bar Nuclear Plant, Unit 1 - Issuance of Amendment Regarding Modification To Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (TAC No. MF6153), dated September 17, 2015 (ML15230A155)
: 3. Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies"
: 4. NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998
: 5. Regulatory Guide 1.9, Revision 1, "Selection, Design, and Qualification of Diesel-Generator Units Used as Onsite Electric Power Systems at Nuclear Power Plants"
: 6. WCAP-17308-NP, Treatment of Diesel Generator (DG) Technical Specification Frequency and Voltage Tolerances, April 2012
: 7. G-Spec G-37 R5, Testing and Balancing of HVAC Systems During Installation, Modification, and Maintenance
: 7. G-Spec G-37 R5, Testing and Balancing of HVAC Systems During Installation, Modification, and Maintenance
: 8. Regulatory Guide 1.6, Revision 0, "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems (Safety Guide 6)" 9. NUREG-1232, Volume 2, "Safety Evaluation Report On Tennessee Valley Authority: Sequoyah Nuclear Performance Plan," dated May 1988 10. NRC Letter, "Beaver Valley 1 and 2 - Amendment for Revised Technical Specification Requirements for Emergency Diesel Generators (TAC Nos. MA4438 and MA4439)," dated February 11, 2000 (ML003684928)
: 8. Regulatory Guide 1.6, Revision 0, "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems (Safety Guide 6)"
: 11. NRC Letter, "Palo Verde Nuclear Generating Station, Units 1, 2, and 3 - Issuance of Amendments on Diesel Generator Steady
: 9. NUREG-1232, Volume 2, Safety Evaluation Report On Tennessee Valley Authority: Sequoyah Nuclear Performance Plan, dated May 1988
-State Voltage and Frequency (TAC Nos. MA9214, MA9215, and MA9216)," dated October 4, 2000 (ML003758500)
: 10. NRC Letter, "Beaver Valley 1 and 2 - Amendment for Revised Technical Specification Requirements for Emergency Diesel Generators (TAC Nos. MA4438 and MA4439)," dated February 11, 2000 (ML003684928)
: 12. NRC Letter, "Donald C. Cook Nuclear Plant, Units 1 and 2 - Issuance of Amendment to Renewed Facility Operating License Regarding Technical Specification Change Relating to Diesel Generator Steady
: 11. NRC Letter, "Palo Verde Nuclear Generating Station, Units 1, 2, and 3 - Issuance of Amendments on Diesel Generator Steady-State Voltage and Frequency (TAC Nos. MA9214, MA9215, and MA9216)," dated October 4, 2000 (ML003758500)
-State Parameters (TAC Nos. MD8773 and MD8774)," dated April 30, 2009 (ML090630245)
: 12. NRC Letter, Donald C. Cook Nuclear Plant, Units 1 and 2 - Issuance of Amendment to Renewed Facility Operating License Regarding Technical Specification Change Relating to Diesel Generator Steady-State Parameters (TAC Nos. MD8773 and MD8774), dated April 30, 2009 (ML090630245)
: 13. NRC Letter, "Crystal River Unit 3 Nuclear Generating Plant - Issuance of Amendment Regarding Request to Revise the Technical Specification Surveillance Requirements for Emergency Diesel Generator Voltage and Frequency Limits (TAC No. ME0107)," dated December 10, 2009 (ML092680285)
: 13. NRC Letter, "Crystal River Unit 3 Nuclear Generating Plant - Issuance of Amendment Regarding Request to Revise the Technical Specification Surveillance Requirements for Emergency Diesel Generator Voltage and Frequency Limits (TAC No. ME0107), dated December 10, 2009 (ML092680285)
CNL-16-001                                E19 of 20


ENCLOSURE   CNL-16-001 E 20 of 20  14. NRC Letter, "Wolf Creek Generating Station - Issuance of Amendment Re: Revise Technical Specification 3.8.1, "AC Sources - Operating" (TAC No. ME7674)," dated April 11, 2013 (ML13077A147)
ENCLOSURE
: 14. NRC Letter, "Wolf Creek Generating Station - Issuance of Amendment Re: Revise Technical Specification 3.8.1, "AC Sources - Operating" (TAC No. ME7674),"
dated April 11, 2013 (ML13077A147)
CNL-16-001                                E20 of 20


AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-6 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
ATTACHMENT 1 Proposed TS Changes (Mark-Ups) for SQN Units 1 and 2
SURVEILLANCE FREQUENCY  SR  3.8.1.2
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading. 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
    ---------------------------------------------------------------------
Verify each DG starts from standby conditions and  6800 V and 7260  58.8 Hz  61.2 Hz.       


In accordance with the Surveillance Frequency Control Program   SR 3.8.1.3
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
------------------------------NOTES-----------------------------
SURVEILLANCE                                                  FREQUENCY SR 3.8.1.2    ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
Verify each DG starts from standby conditions and                      In accordance achieves steady state voltage  6800 V and                            with the 7260 V, and frequency  58.8 Hz and  61.2 Hz.                      Surveillance Frequency Control Program 59.8                                        60.2 SR 3.8.1.3   ------------------------------NOTES-----------------------------
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 2. Momentary transients outside the load range do not invalidate this test.
: 2. Momentary transients outside the load range do not invalidate this test.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.   ---------------------------------------------------------------------
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.
Verify each DG is synchronized and loaded and                          In accordance operates for  60 minutes at a load  3960 kW and                      with the 4400 kW.                                                            Surveillance Frequency Control Program SEQUOYAH - UNIT 1                              3.8.1-6                                    Amendment 334


Verify each DG is synchronized and loaded and  60 minutes at a load 3960 kW and  4400 kW.  
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE                                                  FREQUENCY SR 3.8.1.4    Verify each engine-mounted day tank contains                        In accordance 250 gal of fuel oil.                                                with the Surveillance Frequency Control Program SR 3.8.1.5    Check for and remove accumulated water from each                      In accordance engine-mounted day tank.                                            with the Surveillance Frequency Control Program SR 3.8.1.6    Verify the fuel oil transfer system operates to                        In accordance transfer fuel oil from the storage system to the                      with the engine-mounted day tanks.                                            Surveillance Frequency Control Program SR 3.8.1.7    ------------------------------NOTE-------------------------------
All DG starts may be preceded by an engine prelube period.
Verify each DG starts from standby condition and                      In accordance achieves:                                                              with the Surveillance
: a. In  10 seconds, voltage  6800 V and                            Frequency frequency  58.8 Hz and                                         Control Program
: b. Steady state voltage  6800 V and  7260 V, and frequency 58.8 Hz and  61.2 Hz.
59.8                60.2 SEQUOYAH - UNIT 1                              3.8.1-7                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-7 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.4 Verify each engine
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.8    ------------------------------NOTES-----------------------------
-mounted "day" tank contains  250 gal of fuel oil.
: 1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.5 Check for and remove accumulated water from each engine-mounted "day" tank.
: 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
In accordance with the Surveillance Frequency Control Program   SR  3.8.1.6 Verify the fuel oil transfer system operates to transfer fuel oil from the storage system to the engine-mounted "day" tanks.
Verify automatic and manual transfer of the power                     In accordance supply to each 6.9 kV Unit Board from the normal                       with the supply to the alternate supply.                                       Surveillance Frequency Control Program SR 3.8.1.9   ------------------------------NOTE------------------------------
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.7
------------------------------NOTE-------------------------------
All DG starts may be preceded by an engine prelube period.  ---------------------------------------------------------------------
 
Verify each DG starts from standby condition and achieves:    a. In  10 seconds, volta 6800 V and  58.8 Hz and    b. Steady state voltage  6800 V and  7260 V, and frequency  58.8 Hz and  61.2 Hz.        In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1  SEQUOYAH - UNIT 1 3.8.1-8 Amendment 334 SURVEILLANCE REQUIREMENTS  (continued)
SURVEILLANCE FREQUENCY  SR  3.8.1.8
------------------------------NOTE S-----------------------------
: 1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR. 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
---------------------------------------------------------------------
Verify automatic and manual transfer of the power supply to each 6.9 kV Unit Board from the normal supply to the alternate supply.
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.9
------------------------------NOTE------------------------------
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
Under this condition the power factor shall be maintained as close to the limit as practicable.   ---------------------------------------------------------------------
Under this condition the power factor shall be maintained as close to the limit as practicable.
Verify each DG rejects a load greater than or equal                    In accordance to its associated single largest post-accident load,                  with the and:                                                                  Surveillance Frequency
: a. Following load rejection, the frequency is                      Control Program 66.5 Hz,
: b. Within 3 seconds following load rejection, the voltage is  6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is  58.8 Hz and  61.2 Hz.
SEQUOYAH - UNIT 1      59.8                  60.2 3.8.1-8                                    Amendment 334


Verify each DG rejects a load greater than or equal to its associated single largest post
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
-accident load, and:
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.11   ------------------------------NOTES-----------------------------
: a. Following load rejection, the frequency is  66.5 Hz,    b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is 58.8 Hz and  61.2 Hz.   
 
In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-10 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.11
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, thi s Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated loss of offsite power                 In accordance signal:                                                               with the Surveillance
Verify on an actual or simulated loss of offsite power signal:
: a. De-energization of shutdown boards,                             Frequency Control Program
: a. De-energization of shutdown boards,     b. Load shedding from shutdown boards,
: b. Load shedding from shutdown boards,
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in  10 seconds,
: 1.     Energizes permanently connected loads in  10 seconds,
: 2. Energizes auto
: 2.     Energizes auto-connected shutdown loads through load sequence timers,
-connected shutdown loads through load sequence timers,
: 3.     Maintains steady state voltage 6800 V and 7260 V,
: 3. Maintains steady state voltage 6800 V and   7260 V,
: 4.     Maintains steady state frequency 58.8 Hz and 61.2 Hz, and
: 4. Maintains steady state frequency 58.8 Hz and   61.2 Hz, and
: 5.     Supplies permanently connected and auto-connected shutdown loads for 59.8                  60.2 5 minutes.
: 5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.  
SEQUOYAH - UNIT 1                            3.8.1-10                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-11 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.12
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.12     ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by prelube period.
: 1. All DG starts may be preceded by prelube period. 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated Engineered Safety                     In accordance Feature (ESF) actuation signal each DG auto-starts                     with the from standby condition and:                                           Surveillance Frequency
Verify on an actual or simulated Engineered Safety Feature (ESF) actuation signal each DG auto
: a. In  10 seconds after auto-start and during                     Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
-starts from standby condition and:
: b. Achieves steady state voltage  6800 V and 7260 V and frequency  58.8 Hz and 61.2 Hz,
: a. 10 seconds after auto
: c. Operates for  5 minutes, 59.8 60.2 d. Permanently connected loads remain energized from the offsite power system, and
-start and during  6800 V and frequency 58.8 Hz,
: b. 6800 V and   58.8 Hz and 61.2 H z,     c. 5 minutes,     d. Permanently connected loads remain energized from the offsite power system, and
: e. Emergency loads are energized from the offsite power system.
: e. Emergency loads are energized from the offsite power system.
SEQUOYAH - UNIT 1                                3.8.1-11                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-13 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.15 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.15   ------------------------------NOTES-----------------------------
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours load 3960 kW and 4400 kW   2370 kvar.
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loaded  3960 kW and 4400 kW and  2140 kvar and  2370 kvar.
Momentary transients outside of load range do not invalidate this test.
Momentary transients outside of load range do not invalidate this test.
: 2. All DG starts may be preceded by an engine prelube period.
: 2. All DG starts may be preceded by an engine prelube period.
    ---------------------------------------------------------------------
Verify each DG starts and achieves:                                   In accordance with the
 
: a. In  10 seconds, voltage 6800 V and                           Surveillance frequency 58.8 Hz and                                         Frequency Control Program
Verify each DG starts and achieves:
: b. Steady state voltage  6800 V, and 7260 V and frequency 58.8 Hz and 61.2 Hz.
: a. 10  6800 V and  58.8 Hz and
SR 3.8.1.16   ------------------------------NOTE-------------------------------
: b. 6800  7260 V  58.8  61.2 Hz.  
For DGs 59.8 1A-A and 1B-B,   60.2this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
 
Verify each DG:                                                       In accordance with the
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.16 ------------------------------NOTE-------------------------------
: a. Synchronizes with offsite power source while                     Surveillance loaded with emergency loads upon a simulated                     Frequency restoration of offsite power,                                   Control Program
For DGs 1A
-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
  ---------------------------------------------------------------------
 
Verify each DG:
: a. Synchronizes with offsite power source while loaded with emergency loads upon a simulated restoration of offsite power,
: b. Transfers loads to offsite power source, and
: b. Transfers loads to offsite power source, and
: c. Returns to ready
: c. Returns to ready-to-load operation.
-to-load operation.
SEQUOYAH - UNIT 1                            3.8.1-13                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-15 Amendment 334 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.18 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.18   ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated loss of offsite power                 In accordance signal in conjunction with an actual or simulated                     with the ESF actuation signal:                                                 Surveillance Frequency
 
: a. De-energization of shutdown boards,                               Control Program
Verify on an actual or simulated loss of offsite power signal in conjunction with an actual or simulated ESF actuation signal:
: b. Load shedding from shutdown boards, and
: a. De-energization of shutdown boards, b. Load shedding from shutdown boards, and
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in 10 seconds, 2. Energizes auto
: 1. Energizes permanently connected loads in 10 seconds,
-connected emergency loads through load sequence timers,
: 2. Energizes auto-connected emergency loads through load sequence timers,
: 3. 6800 V  7260 V,
: 3. Achieves steady state voltage  6800 V and 7260 V,
: 4. Ach 58.8 Hz  61.2 Hz, and 5. Supplies permanently connected and auto
: 4. Achieves steady state frequency  58.8 Hz and 61.2 Hz, and
-connected emergency loads for  5 minutes.  
: 5. Supplies permanently connected and auto-connected emergency 59.8      loads for 60.2 5 minutes.
SEQUOYAH - UNIT 1                            3.8.1-15                                    Amendment 334


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-6 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.2
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.2   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading. 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
    ---------------------------------------------------------------------
Verify each DG starts from standby conditions and                     In accordance achieves steady state voltage 6800 V and                             with the 7260 V, and frequency 58.8 Hz and 61.2 Hz.                       Surveillance Frequency Control Program 59.8                                        60.2 SR 3.8.1.3   ------------------------------NOTES-----------------------------
Verify each DG starts from standby conditions and  6800 V and 7260  58.8 H z 61.2 H z.  
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.3
------------------------------NOTES-----------------------------
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 2. Momentary transients outside the load range do not invalidate this test.
: 2. Momentary transients outside the load range do not invalidate this test.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.   ---------------------------------------------------------------------
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.
 
Verify each DG is synchronized and loaded and                         In accordance operates for 60 minutes at a load  3960 kW and                     with the 4400 kW.                                                             Surveillance Frequency Control Program SEQUOYAH - UNIT 2                              3.8.1-6                                    Amendment 327
Verify each DG is synchronized and loaded and  60 minutes at a load  3960 kW and 4400 kW.  


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-7 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.4 Verify each engine
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.4   Verify each engine-mounted day tank contains                         In accordance 250 gal of fuel oil.                                                 with the Surveillance Frequency Control Program SR 3.8.1.5   Check for and remove accumulated water from each                       In accordance engine-mounted day tank.                                             with the Surveillance Frequency Control Program SR 3.8.1.6   Verify the fuel oil transfer system operates to                       In accordance transfer fuel oil from the storage system to the                      with the engine-mounted day tanks.                                           Surveillance Frequency Control Program SR 3.8.1.7   ------------------------------NOTE-------------------------------
-mounted "day" tank contains 250 gal of fuel oil.
All DG starts may be preceded by an engine prelube period.
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.5 Check for and remove accumulated water from each engine-mounted "day" tank.
Verify each DG starts from standby condition and                      In accordance achieves:                                                              with the Surveillance
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.6 Verify the fuel oil transfer system operates to transfer fuel oil from the storage system to the engine-mounted "day" tanks.
: a. In  10 seconds, voltage  6800 V and                            Frequency frequency  58.8 Hz and                                          Control Program
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.7
: b. Steady state voltage 6800 V and  7260 V, and frequency  58.8 Hz and  61.2 Hz.
------------------------------NOTE-------------------------------
59.8                                            60.2 SEQUOYAH - UNIT 2                              3.8.1-7                                    Amendment 327
All DG starts may be preceded by an engine prelube period.  ---------------------------------------------------------------------


Verify each DG starts from standby condition and achieves:    a. In  10 seconds, volta 6800 V and  58.8 Hz and    b. Steady state voltage  6800 V and  7260 V, and frequency  58.8 Hz and  61.2 Hz.        In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-8 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.8
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.8   ------------------------------NOTES-----------------------------
------------------------------NOTE S-----------------------------
: 1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
: 1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR. 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
: 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
---------------------------------------------------------------------
Verify automatic and manual transfer of the power                     In accordance supply to each 6.9 kV Unit Board from the normal                       with the supply to the alternate supply.                                       Surveillance Frequency Control Program SR 3.8.1.9   ------------------------------NOTE-------------------------------
Verify automatic and manual transfer of the power supply to each 6.9 kV Unit Board from the normal supply to the alternate supply.
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.9
------------------------------NOTE-------------------------------
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
Under this condition the power factor shall be maintained as close to the limit as practicable.   ---------------------------------------------------------------------
Under this condition the power factor shall be maintained as close to the limit as practicable.
Verify each DG rejects a load greater than or equal                    In accordance to its associated single largest post-accident load,                  with the and:                                                                  Surveillance Frequency
: a. Following load rejection, the frequency is                      Control Program 66.5 Hz,
: b. Within 3 seconds following load rejection, the voltage is  6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is  58.8 Hz and  61.2 Hz.
59.8                    60.2 SEQUOYAH - UNIT 2                              3.8.1-8                                    Amendment 327


Verify each DG rejects a load greater than or equal to its associated single largest post
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
-accident load, and:
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.11   ------------------------------NOTES-----------------------------
: a. Following load rejection, the frequency is  66.5 Hz,    b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is 58.8 Hz and  61.2 Hz.   
 
In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-10 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.11
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 2A-A and 2B-B, thi s Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated loss of offsite power signal:
Verify on an actual or simulated loss of offsite power                 In accordance signal:                                                               with the Surveillance
: a. De-energization of shutdown boards,     b. Load shedding from shutdown boards,
: a. De-energization of shutdown boards,                             Frequency Control Program
: b. Load shedding from shutdown boards,
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in  10 seconds,
: 1.     Energizes permanently connected loads in  10 seconds,
: 2. Energizes auto
: 2.     Energizes auto-connected shutdown loads through load sequence timers,
-connected shutdown loads through load sequence timers,
: 3.     Maintains steady state voltage 6800 V and 7260 V,
: 3. Maintains steady state voltage 6800 V and   7260 V,
: 4.     Maintains steady state frequency 58.8 Hz and 61.2 Hz, and
: 4. Maintains steady state frequency 58.8 Hz and   61.2 Hz, and
: 5.     Supplies permanently connected and auto-connected shutdown loads for 59.8                  60.2 5 minutes.
: 5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.  
SEQUOYAH - UNIT 2                            3.8.1-10                                    Amendment 327


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-11 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.12
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.12     ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by prelube period.
: 1. All DG starts may be preceded by prelube period. 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated Engineered Safety Feature (ESF) actuation signal each DG auto
Verify on an actual or simulated Engineered Safety                     In accordance Feature (ESF) actuation signal each DG auto-starts                     with the from standby condition and:                                           Surveillance Frequency
-starts from standby condition and:
: a. In  10 seconds after auto-start and during                     Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
: a. 10 seconds after auto
: b. Achieves steady state voltage  6800 V and 7260 V and frequency  58.8 Hz and 61.2 Hz,
-start and during  6800 V and frequency 58.8 Hz,
: c. Operates for  5 minutes, 59.8
: b. 6800 V and   58.8 Hz and 61.2 H z,     c. 5 minutes,     d. Permanently connected loads remain energized from the offsite power system, and
: d. Permanently connected loads remain energized 60.2      from the offsite power system, and
: e. Emergency loads are energized from the offsite power system.
: e. Emergency loads are energized from the offsite power system.
SEQUOYAH - UNIT 2                                3.8.1-11                                    Amendment 327


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-13 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.15 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.15   ------------------------------NOTES-----------------------------
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loa 3960 kW and 4400 kW   2370 kvar.
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loaded  3960 kW and 4400 kW and  2140 kvar and  2370 kvar.
Momentary transients outside of load range do not invalidate this test.
Momentary transients outside of load range do not invalidate this test.
: 2. All DG starts may be preceded by an engine prelube period.
: 2. All DG starts may be preceded by an engine prelube period.
    ---------------------------------------------------------------------
Verify each DG starts and achieves:                                   In accordance with the
 
: a. In  10 seconds, voltage 6800 V and                           Surveillance frequency 58.8 Hz and                                         Frequency Control Program
Verify each DG starts and achieves:
: b. Steady state voltage  6800 V, and 7260 V and frequency 58.8 Hz and 61.2 Hz.
: a. 10  6800 V and  58.8 Hz and
SR 3.8.1.16   ------------------------------NOTE-------------------------------
: b. 6800  7260 V  58.8  61.2 Hz.  
For DGs 59.82A-A and 2B-B, this Surveillance shall         60.2not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
 
Verify each DG:                                                       In accordance with the
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.16 ------------------------------NOTE-------------------------------
: a. Synchronizes with offsite power source while                     Surveillance loaded with emergency loads upon a simulated                     Frequency restoration of offsite power,                                   Control Program
For DGs 2A-A and 2B-B, this Surveillance shall no t normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
  ---------------------------------------------------------------------
 
Verify each DG:
: a. Synchronizes with offsite power source while loaded with emergency loads upon a simulated restoration of offsite power,
: b. Transfers loads to offsite power source, and
: b. Transfers loads to offsite power source, and
: c. Returns to ready
: c. Returns to ready-to-load operation.
-to-load operation.
SEQUOYAH - UNIT 2                            3.8.1-13                                    Amendment 327


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-15 Amendment 327 SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.18 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.18   ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated loss of offsite power signal in conjunction with an actual or simulated ESF actuation signal:
Verify on an actual or simulated loss of offsite power                 In accordance signal in conjunction with an actual or simulated                     with the ESF actuation signal:                                                 Surveillance Frequency
: a. De-energization of shutdown boards, b. Load shedding from shutdown boards, and
: a. De-energization of shutdown boards,                               Control Program
: b. Load shedding from shutdown boards, and
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in 10 seconds, 2. Energizes auto
: 1. Energizes permanently connected loads in 10 seconds,
-connected emergency loads through load sequence timers,
: 2. Energizes auto-connected emergency loads through load sequence timers,
: 3. 6800 V  7260 V,
: 3. Achieves steady state voltage  6800 V and 7260 V,
: 4. Ach 58.8 Hz  61.2 Hz, and 5. Supplies permanently connected and auto
: 4. Achieves steady state frequency  58.8 Hz and 61.2 Hz, and
-connected emergency loads for 5 minutes.  
: 5. Supplies permanently connected and auto-connected emergency loads       59.8 for 5 minutes. 60.2 SEQUOYAH - UNIT 2                            3.8.1-15                                    Amendment 327
 
In accordance with the Surveillance Frequency Control Program 


AC Sources - Operating B 3.8.1    SEQUOYAH - UNIT 1 B 3.8.1-16 Revision 45 BASES  SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8). Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref.
ATTACHMENT 2 Proposed TS Bases Changes (Mark-Ups) for SQN Units 1 and 2 (For Information Only)
9).
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable.
The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating. The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages. The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/-
2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).
SR  3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained. 


AC Sources - Operating B 3.8.1 BASES SURVEILLANCE    The AC sources are designed to permit inspection and testing of all REQUIREMENTS    important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).
Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.
The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.
The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/- 2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3).
These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
SEQUOYAH - UNIT 1                      B 3.8.1-16                                    Revision 45


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 1 B 3.8.1-17 Revision 45 BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 During this testing, the diesel is BASES                                                     not in an accident mode and the frequency is controlled by SURVEILLANCE REQUIREMENTS (continued)                     the operator instead of the governors accident speed SR 3.8.1.2 and SR 3.8.1.7                 reference.
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
 
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2. SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.
SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 1                      B 3.8.1-17                                    Revision 45


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 1 B 3.8.1-21 Revision 45 BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post-accident load with the DG solely supplying the board.       and Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejectionmaximum test is   transient acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
: b. Tripping its associated single largest post
-accident load with the DG solely supplying the board. Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
 
The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.
The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than  0.89.
These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to  0.89 results in voltages on the emergency boards that are too high.
SEQUOYAH - UNIT 1                        B 3.8.1-21                              Revision 45


This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows  0.89. These conditions occur when grid voltage is high, and the additional field 0.89 results in voltages on the emergency boards that are too high. 
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE     The AC sources are designed to permit inspection and testing of all REQUIREMENTS     important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).
 
Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).
AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-16 Revision 44 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8). Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref.
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.
9). Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating. The specified maximum steady state output voltage o f 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages. The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/-
The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.
2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).
The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/- 2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
 
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.                         The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3).
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
 
SEQUOYAH - UNIT 2                       B 3.8.1-16                                    Revision 44
AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-17 Revision 45 BASES  SURVEILLANCE REQUIREMENTS  (continued)
SR  3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.


AC Sources - Operating B 3.8.1 During this testing, the diesel is not in an accident mode and BASES                                                          the frequency is controlled by the operator instead of the SURVEILLANCE REQUIREMENTS (continued)                          governors accident speed reference.
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2. SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.
SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 2                      B 3.8.1-17                                  Revision 45


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-21 Revision 45 BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post-accident load with the DG solely supplying the board.       and Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejectionmaximum test is   transient acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
: b. Tripping its associated single largest post
-accident load with the DG solely supplying the board. Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
 
The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.
The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than  0.89.
These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to  0.89 results in voltages on the emergency boards that are too high.
SEQUOYAH - UNIT 2                        B 3.8.1-21                              Revision 45


This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows  0.89. These conditions occur when grid voltage is high, and the additional field 0.89 results in voltages on the emergency boards that are too high.
ATTACHMENT 3 Proposed TS Changes (Final Typed) for SQN Units 1 and 2


AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-6 Amendment 33 X  SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.2
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.2   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
    ---------------------------------------------------------------------
Verify each DG starts from standby conditions and                     In accordance achieves steady state voltage 6800 V and                             with the 7260 V, and frequency 59.8 Hz and 60.2 Hz.                       Surveillance Frequency Control Program SR 3.8.1.3   ------------------------------NOTES-----------------------------
Verify each DG starts from standby conditions and  6800 V and 7260  59.8 Hz  60.2 Hz.      
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.3
------------------------------NOTES-----------------------------
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 2. Momentary transients outside the load range do not invalidate this test.
: 2. Momentary transients outside the load range do not invalidate this test.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.   ---------------------------------------------------------------------
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.
Verify each DG is synchronized and loaded and                          In accordance operates for  60 minutes at a load  3960 kW and                      with the 4400 kW.                                                            Surveillance Frequency Control Program SEQUOYAH - UNIT 1                              3.8.1-6                                  Amendment 33X


Verify each DG is synchronized and loaded and  60 minutes at a load 3960 kW and  4400 kW.  
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE                                                  FREQUENCY SR 3.8.1.4    Verify each engine-mounted day tank contains                        In accordance 250 gal of fuel oil.                                                with the Surveillance Frequency Control Program SR 3.8.1.5    Check for and remove accumulated water from each                      In accordance engine-mounted day tank.                                            with the Surveillance Frequency Control Program SR 3.8.1.6    Verify the fuel oil transfer system operates to                        In accordance transfer fuel oil from the storage system to the                      with the engine-mounted day tanks.                                            Surveillance Frequency Control Program SR 3.8.1.7    ------------------------------NOTE-------------------------------
All DG starts may be preceded by an engine prelube period.
Verify each DG starts from standby condition and                      In accordance achieves:                                                              with the Surveillance
: a. In  10 seconds, voltage  6800 V and                           Frequency frequency  58.8 Hz and                                         Control Program
: b. Steady state voltage 6800 V and 7260 V, and frequency 59.8 Hz and  60.2 Hz.
SEQUOYAH - UNIT 1                              3.8.1-7                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-7 Amendment 33 X  SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR  3.8.1.4 Verify each engine
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.8    ------------------------------NOTES-----------------------------
-mounted "day" tank contains  250 gal of fuel oil.
: 1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.5 Check for and remove accumulated water from each engine-mounted "day" tank.
: 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.6 Verify the fuel oil transfer system operates t o  transfer fuel oil from the storage system to the engine-mounted "day" tanks.
Verify automatic and manual transfer of the power                     In accordance supply to each 6.9 kV Unit Board from the normal                       with the supply to the alternate supply.                                       Surveillance Frequency Control Program SR 3.8.1.9   ------------------------------NOTE------------------------------
In accordance with the Surveillance Frequency Control Program   SR  3.8.1.7
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
------------------------------NOTE-------------------------------
Under this condition the power factor shall be maintained as close to the limit as practicable.
All DG starts may be preceded by an engine prelube period.  ---------------------------------------------------------------------
Verify each DG rejects a load greater than or equal                   In accordance to its associated single largest post-accident load,                   with the and:                                                                   Surveillance Frequency
 
: a. Following load rejection, the frequency is                       Control Program 66.5 Hz,
Verify each DG starts from standby condition and achieves:    a. In  10 seconds, vol 6800 V and  58.8 Hz and
: b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: b. Steady state voltage  6800 V and  7260 V, and frequency  59.8 Hz and  60.2 Hz.        In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1  SEQUOYAH - UNIT 1 3.8.1-8 Amendment 33 X  SURVEILLANCE REQUIREMENTS  (continued)
: c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and  60.2 Hz.
SURVEILLANCE FREQUENCY  SR  3.8.1.8
SEQUOYAH - UNIT 1                              3.8.1-8                                  Amendment 33X
------------------------------NOTE S-----------------------------
: 1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR. 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
---------------------------------------------------------------------
Verify automatic and manual transfer of the power supply to each 6.9 kV Unit Board from the normal supply to the alternate supply.
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.9
------------------------------NOTE------------------------------
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met. Under this condition the power factor shall be maintained as close to the limit as practicable.   ---------------------------------------------------------------------
 
Verify each DG rejects a load greater than or equal to its associated single largest post
-accident load, and:
: a. Following load rejection, the frequency is 66.5 Hz,     b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and  60.2 Hz.  


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-10 Amendment 33X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.11
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.11   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, th is Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated loss of offsite power                 In accordance signal:                                                               with the Surveillance
Verify on an actual or simulated loss of offsite power signal:
: a. De-energization of shutdown boards,                             Frequency Control Program
: a. De-energization of shutdown boards,     b. Load shedding from shutdown boards,
: b. Load shedding from shutdown boards,
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in  10 seconds,
: 1.     Energizes permanently connected loads in  10 seconds,
: 2. Energizes auto
: 2.     Energizes auto-connected shutdown loads through load sequence timers,
-connected shutdown loads through load sequence timers,
: 3.     Maintains steady state voltage 6800 V and 7260 V,
: 3. Maintains steady state voltage 6800 V and   7260 V,
: 4.     Maintains steady state frequency 59.8 Hz and 60.2 Hz, and
: 4. Maintains steady state frequency 59.8 Hz and   60.2 Hz, and
: 5.     Supplies permanently connected and auto-connected shutdown loads for 5 minutes.
: 5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.        
SEQUOYAH - UNIT 1                            3.8.1-10                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-11 Amendment 33X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.12
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.12   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by prelube period.
: 1. All DG starts may be preceded by prelube period. 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated Engineered Safety                     In accordance Feature (ESF) actuation signal each DG auto-starts                     with the from standby condition and:                                           Surveillance Frequency
Verify on an actual or simulated Engineered Safety Feature (ESF) actuation signal each DG auto
: a. In  10 seconds after auto-start and during                     Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
-starts from standby condition and:
: b. Achieves steady state voltage  6800 V and 7260 V and frequency  59.8 Hz and 60.2 Hz,
: a. 10 seconds after auto
: c. Operates for  5 minutes,
-start and during  6800 V and frequency 58.8 Hz,
: d. Permanently connected loads remain energized from the offsite power system, and
: b. 6800 V and   59.8 Hz and 60.2 Hz,     c. 5 minutes,     d. Permanently connected loads remain energized from the offsite power system, and
: e. Emergency loads are energized from the offsite power system.
: e. Emergency loads are energized from the offsite power system.
SEQUOYAH - UNIT 1                            3.8.1-11                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-13 Amendment 33X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.15 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.15   ------------------------------NOTES-----------------------------
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loa 3960 kW and 4400 kW   2370 kvar.
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loaded  3960 kW and 4400 kW and  2140 kvar and  2370 kvar.
Momentary transients outside of load range do not invalidate this test.
Momentary transients outside of load range do not invalidate this test.
: 2. All DG starts may be preceded by an engine prelube period.
: 2. All DG starts may be preceded by an engine prelube period.
    ---------------------------------------------------------------------
Verify each DG starts and achieves:                                   In accordance with the
 
: a. In  10 seconds, voltage 6800 V and                           Surveillance frequency 58.8 Hz and                                         Frequency Control Program
Verify each DG starts and achieves:
: b. Steady state voltage  6800 V, and 7260 V and frequency 59.8 Hz and 60.2 Hz.
: a. 10  6800 V and  58.8 Hz and
SR 3.8.1.16   ------------------------------NOTE-------------------------------
: b. 6800  7260 V  59.8  60.2 Hz.  
For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
 
Verify each DG:                                                       In accordance with the
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.16 ------------------------------NOTE-------------------------------
: a. Synchronizes with offsite power source while                     Surveillance loaded with emergency loads upon a simulated                     Frequency restoration of offsite power,                                   Control Program
For DGs 1A
-A and 1B-B, this Surveillance shall no t normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
  ---------------------------------------------------------------------
 
Verify each DG:
: a. Synchronizes with offsite power source while loaded with emergency loads upon a simulated restoration of offsite power,
: b. Transfers loads to offsite power source, and
: b. Transfers loads to offsite power source, and
: c. Returns to ready
: c. Returns to ready-to-load operation.
-to-load operation.
SEQUOYAH - UNIT 1                            3.8.1-13                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 1 3.8.1-15 Amendment 33X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.18 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.18   ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 1A
: 2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
-A and 1B-B, t his Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
Verify on an actual or simulated loss of offsite power                 In accordance signal in conjunction with an actual or simulated                     with the ESF actuation signal:                                                 Surveillance Frequency
Verify on an actual or simulated loss of offsite power signal in conjunction with an actual or simulated ESF actuation signal:
: a. De-energization of shutdown boards,                               Control Program
: a. De-energization of shutdown boards, b. Load shedding from shutdown boards, and
: b. Load shedding from shutdown boards, and
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in 10 seconds, 2. Energizes auto
: 1. Energizes permanently connected loads in 10 seconds,
-connected emergency loads through load sequence timers,
: 2. Energizes auto-connected emergency loads through load sequence timers,
: 3. 6800 V  7260 V,
: 3. Achieves steady state voltage  6800 V and 7260 V,
: 4. Ach i 59.8 Hz  60.2 Hz, and 5. Supplies permanently connected and auto
: 4. Achieves steady state frequency  59.8 Hz and 60.2 Hz, and
-connected emergency loads for 5 minutes.  
: 5. Supplies permanently connected and auto-connected emergency loads for 5 minutes.
SEQUOYAH - UNIT 1                            3.8.1-15                                  Amendment 33X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-6 Amendment 32X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.2
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.2   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
: 2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.
    ---------------------------------------------------------------------
Verify each DG starts from standby conditions and                     In accordance achieves steady state voltage 6800 V and                             with the 7260 V, and frequency 59.8 Hz and 60.2 Hz.                       Surveillance Frequency Control Program SR 3.8.1.3   ------------------------------NOTES-----------------------------
Verify each DG starts from standby conditions and  6800 V and 7260  59.8 Hz  60.2 Hz.      
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.3
------------------------------NOTES-----------------------------
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 1. DG loadings may include gradual loading as recommended by the manufacturer.
: 2. Momentary transients outside the load range do not invalidate this test.
: 2. Momentary transients outside the load range do not invalidate this test.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 3. This Surveillance shall be conducted on only one DG at a time.
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.   ---------------------------------------------------------------------
: 4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.
Verify each DG is synchronized and loaded and                          In accordance operates for  60 minutes at a load  3960 kW and                      with the 4400 kW.                                                            Surveillance Frequency Control Program SEQUOYAH - UNIT 2                              3.8.1-6                                  Amendment 32X


Verify each DG is synchronized and loaded and  60 minutes at a load 3960 kW and  4400 kW.  
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE                                                  FREQUENCY SR 3.8.1.4    Verify each engine-mounted day tank contains                        In accordance 250 gal of fuel oil.                                                with the Surveillance Frequency Control Program SR 3.8.1.5    Check for and remove accumulated water from each                      In accordance engine-mounted day tank.                                            with the Surveillance Frequency Control Program SR 3.8.1.6    Verify the fuel oil transfer system operates to                        In accordance transfer fuel oil from the storage system to the                      with the engine-mounted day tanks.                                            Surveillance Frequency Control Program SR 3.8.1.7    ------------------------------NOTE-------------------------------
All DG starts may be preceded by an engine prelube period.
Verify each DG starts from standby condition and                      In accordance achieves:                                                              with the Surveillance
: a. In  10 seconds, voltage  6800 V and                           Frequency frequency  58.8 Hz and                                         Control Program
: b. Steady state voltage 6800 V and 7260 V, and frequency 59.8 Hz and  60.2 Hz.
SEQUOYAH - UNIT 2                              3.8.1-7                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-7 Amendment 32X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.4 Verify each engine
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.8    ------------------------------NOTES-----------------------------
-mounted "day" tank contains  250 gal of fuel oil.
: 1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.5 Check for and remove accumulated water from each engine-mounted "day" tank.
: 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
In accordance with the Surveillance Frequency Control Program   SR  3.8.1.6 Verify the fuel oil transfer system operates t o  transfer fuel oil from the storage system to the engine-mounted "day" tanks.
Verify automatic and manual transfer of the power                     In accordance supply to each 6.9 kV Unit Board from the normal                       with the supply to the alternate supply.                                       Surveillance Frequency Control Program SR 3.8.1.9   ------------------------------NOTE-------------------------------
In accordance with the Surveillance Frequency Control Program    SR  3.8.1.7
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.
------------------------------NOTE-------------------------------
Under this condition the power factor shall be maintained as close to the limit as practicable.
All DG starts may be preceded by an engine prelube period.  ---------------------------------------------------------------------
Verify each DG rejects a load greater than or equal                    In accordance to its associated single largest post-accident load,                  with the and:                                                                  Surveillance Frequency
Verify each DG starts from standby condition and achieves:    a. In  10 seconds, volt 6800 V and  58.8 Hz and
: a. Following load rejection, the frequency is                      Control Program 66.5 Hz,
: b. Steady state voltage  6800 V and  7260 V, and frequency  59.8 Hz and  60.2 Hz.        In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1  SEQUOYAH - UNIT 2 3.8.1-8 Amendment 32X SURVEILLANCE REQUIREMENTS  (continued)
: b. Within 3 seconds following load rejection, the voltage is  6800 V and  7260 V, and
SURVEILLANCE FREQUENCY  SR  3.8.1.8
: c. Within 3 seconds following load rejection, the frequency is  59.8 Hz and  60.2 Hz.
------------------------------NOTE S-----------------------------
SEQUOYAH - UNIT 2                              3.8.1-8                                  Amendment 32X
: 1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR. 2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.
---------------------------------------------------------------------
Verify automatic and manual transfer of the power supply to each 6.9 kV Unit Board from the normal supply to the alternate supply.
 
In accordance with the Surveillance Frequency Control Program   SR 3.8.1.9
------------------------------NOTE-------------------------------
If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met. Under this condition the power factor shall be maintained as close to the limit as practicable.   ---------------------------------------------------------------------


Verify each DG rejects a load greater than or equal to its associated single largest post
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
-accident load, and:
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.11   ------------------------------NOTES-----------------------------
: a. Following load rejection, the frequency is  66.5 Hz,    b. Within 3 seconds following load rejection, the voltage is 6800 V and  7260 V, and
: c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and  60.2 Hz.   
 
In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-10 Amendment 32X  SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.11
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 2A-A and 2B-B, thi s Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated loss of offsite power signal:
Verify on an actual or simulated loss of offsite power                 In accordance signal:                                                               with the Surveillance
: a. De-energization of shutdown boards,     b. Load shedding from shutdown boards,
: a. De-energization of shutdown boards,                             Frequency Control Program
: b. Load shedding from shutdown boards,
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in  10 seconds,
: 1.     Energizes permanently connected loads in  10 seconds,
: 2. Energizes auto
: 2.     Energizes auto-connected shutdown loads through load sequence timers,
-connected shutdown loads through load sequence timers,
: 3.     Maintains steady state voltage 6800 V and 7260 V,
: 3. Maintains steady state voltage 6800 V and   7260 V,
: 4.     Maintains steady state frequency 59.8 Hz and 60.2 Hz, and
: 4. Maintains steady state frequency 59.8 Hz and   60.2 Hz, and
: 5.     Supplies permanently connected and auto-connected shutdown loads for 5 minutes.
: 5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.        
SEQUOYAH - UNIT 2                            3.8.1-10                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-11 Amendment 32X  SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.12
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.12   ------------------------------NOTES-----------------------------
------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by prelube period.
: 1. All DG starts may be preceded by prelube period. 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated Engineered Safety Feature (ESF) actuation signal each DG auto
Verify on an actual or simulated Engineered Safety                     In accordance Feature (ESF) actuation signal each DG auto-starts                     with the from standby condition and:                                           Surveillance Frequency
-starts from standby condition and:
: a. In  10 seconds after auto-start and during                     Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
: a. 10 seconds after auto
: b. Achieves steady state voltage  6800 V and 7260 V and frequency  59.8 Hz and 60.2 Hz,
-start and during  6800 V and frequency 58.8 Hz,
: c. Operates for  5 minutes,
: b. 6800 V and   59.8 Hz and 60.2 Hz,     c. 5 minutes,     d. Permanently connected loads remain energized from the offsite power system, and
: d. Permanently connected loads remain energized from the offsite power system, and
: e. Emergency loads are energized from the offsite power system.
: e. Emergency loads are energized from the offsite power system.
SEQUOYAH - UNIT 2                            3.8.1-11                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-13 Amendment 32X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.15 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.15   ------------------------------NOTES-----------------------------
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loa 3960 kW and 4400 kW   2370 kvar.
: 1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated  2 hours loaded  3960 kW and 4400 kW and  2140 kvar and  2370 kvar.
Momentary transients outside of load range do not invalidate this test.
Momentary transients outside of load range do not invalidate this test.
: 2. All DG starts may be preceded by an engine prelube period.
: 2. All DG starts may be preceded by an engine prelube period.
    ---------------------------------------------------------------------
Verify each DG starts and achieves:                                   In accordance with the
 
: a. In  10 seconds, voltage 6800 V and                           Surveillance frequency 58.8 Hz and                                         Frequency Control Program
Verify each DG starts and achieves:
: b. Steady state voltage  6800 V, and 7260 V and frequency 59.8 Hz and 60.2 Hz.
: a. 10  6800 V and  58.8 Hz and
SR 3.8.1.16   ------------------------------NOTE-------------------------------
: b. 6800  7260 V  59.8  60.2 Hz.  
 
In accordance with the Surveillance Frequency Control Program    SR 3.8.1.16 ------------------------------NOTE-------------------------------
For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
  ---------------------------------------------------------------------
Verify each DG:                                                       In accordance with the
 
: a. Synchronizes with offsite power source while                     Surveillance loaded with emergency loads upon a simulated                     Frequency restoration of offsite power,                                   Control Program
Verify each DG:
: a. Synchronizes with offsite power source while loaded with emergency loads upon a simulated restoration of offsite power,
: b. Transfers loads to offsite power source, and
: b. Transfers loads to offsite power source, and
: c. Returns to ready
: c. Returns to ready-to-load operation.
-to-load operation.
SEQUOYAH - UNIT 2                            3.8.1-13                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program AC Sources - Operating 3.8.1   SEQUOYAH - UNIT 2 3.8.1-15 Amendment 32X SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)
SURVEILLANCE FREQUENCY   SR 3.8.1.18 ------------------------------NOTES-----------------------------
SURVEILLANCE                                                 FREQUENCY SR 3.8.1.18   ------------------------------NOTES-----------------------------
: 1. All DG starts may be preceded by an engine prelube period.
: 1. All DG starts may be preceded by an engine prelube period.
: 2. For DGs 2A-A and 2B-B, t his Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.   ---------------------------------------------------------------------
: 2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
Verify on an actual or simulated loss of offsite power signal in conjunction with an actual or simulated ESF actuation signal:
Verify on an actual or simulated loss of offsite power                 In accordance signal in conjunction with an actual or simulated                     with the ESF actuation signal:                                                 Surveillance Frequency
: a. De-energization of shutdown boards, b. Load shedding from shutdown boards, and
: a. De-energization of shutdown boards,                               Control Program
: b. Load shedding from shutdown boards, and
: c. DG auto-starts from standby condition and:
: c. DG auto-starts from standby condition and:
: 1. Energizes permanently connected loads in 10 seconds, 2. Energizes auto
: 1. Energizes permanently connected loads in 10 seconds,
-connected emergency loads through load sequence timers,
: 2. Energizes auto-connected emergency loads through load sequence timers,
: 3. 6800 V  7260 V,
: 3. Achieves steady state voltage  6800 V and 7260 V,
: 4. Ach 59.8 Hz  60.2 Hz, and 5. Supplies permanently connected and auto
: 4. Achieves steady state frequency  59.8 Hz and 60.2 Hz, and
-connected emergency loads for 5 minutes.  
: 5. Supplies permanently connected and auto-connected emergency loads for 5 minutes.
SEQUOYAH - UNIT 2                            3.8.1-15                                  Amendment 32X


In accordance with the Surveillance Frequency Control Program 
ATTACHMENT 4 Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)
 
AC Sources - Operating B 3.8.1    SEQUOYAH - UNIT 1 B 3.8.1-16 Revision XX BASES  SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8). Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref.
9).
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable.
The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating. The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages. The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
SR  3.8.1.1  This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained. 


AC Sources - Operating B 3.8.1 BASES SURVEILLANCE    The AC sources are designed to permit inspection and testing of all REQUIREMENTS    important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).
Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.
The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.
The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 1                      B 3.8.1-16                                Revision XX


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 1 B 3.8.1-17 Revision XX BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2. SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governor's accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used.
During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governors accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
AC Sources - Operating B 3.8.1    SEQUOYAH - UNIT 1 B 3.8.1-21 Revision XX BASES  SURVEILLANCE REQUIREMENTS  (continued)
SEQUOYAH - UNIT 1                       B 3.8.1-17                              Revision XX
SR  3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single l oad (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post
-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post
-accident load with the DG solely supplying the board. Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.


AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post-accident load with the DG solely supplying the board.
Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.
The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than  0.89.
These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to  0.89 results in voltages on the emergency boards that are too high.
SEQUOYAH - UNIT 1                        B 3.8.1-21                              Revision XX


This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows  0.89. These conditions occur when grid voltage is high, and the additional field excitati 0.89 results in voltages on the emergency boards that are too high.
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE     The AC sources are designed to permit inspection and testing of all REQUIREMENTS     important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).
AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-16 Revision XX BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8). Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref.
Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).
9). Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating. The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages. The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.
 
The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.
SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 2                      B 3.8.1-16                                Revision XX


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-17 Revision XX BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.
 
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2. SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governor's accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).
The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used.
During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governors accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
SEQUOYAH - UNIT 2                      B 3.8.1-17                              Revision XX


AC Sources - Operating B 3.8.1   SEQUOYAH - UNIT 2 B 3.8.1-21 Revision XX BASES SURVEILLANCE REQUIREMENTS (continued)
AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post
: a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
-accident load while paralleled to offsite power, or while solely supplying the board, or
: b. Tripping its associated single largest post-accident load with the DG solely supplying the board.
: b. Tripping its associated single largest post
Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
-accident load with the DG solely supplying the board. Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.
The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.
 
The time a nd voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.
 
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.
This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be  0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows  0.89. These conditions occur when grid voltage is high, and the additional field  
These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to  0.89 results in voltages on the emergency boards that are too high.
 
SEQUOYAH - UNIT 2                        B 3.8.1-21                              Revision XX}}
e 0.89 results in voltages on the emergency boards that are too high.}}

Latest revision as of 03:04, 5 February 2020

Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)
ML16148A175
Person / Time
Site: Sequoyah  Tennessee Valley Authority icon.png
Issue date: 05/26/2016
From: James Shea
Tennessee Valley Authority
To:
Document Control Desk, Office of Nuclear Reactor Regulation
References
CNL-16-001
Download: ML16148A175 (67)


Text

Tennessee Valley Authority, 1101 Market Street, Chattanooga, Tennessee 37402 CNL-16-001 May 26, 2016 10 CFR 50.90 U.S. Nuclear Regulatory Commission ATTN: Document Control Desk Washington, D.C. 20555-0001 Sequoyah Nuclear Plant Units 1 and 2 Renewed Facility Operating License Nos. DPR-77 and DPR-79 NRC Docket Nos. 50-327 and 50-328

Subject:

Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)

In accordance with the provisions of Title 10 of the Code of Federal Regulations (10 CFR) 50.90, "Application for amendment of license, construction permit, or early site permit,"

Tennessee Valley Authority (TVA) is submitting a request for an amendment (SQN-TS-14-02) to Renewed Facility Operating License Nos. DPR-77 and DPR-79 for the Sequoyah Nuclear Plant (SQN) Units 1 and 2.

This license amendment request proposes to amend the SQN Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. Currently, the acceptance criteria are 58.8 Hz and 61.2 Hz. TVA proposes to change the SQN DG steady state frequency acceptance criteria to 59.8 Hz and 60.2 Hz. The DG TS SR steady state voltage range of 6800 V and 7260 V is unaffected.

TVA has determined that the steady state frequency range acceptance criteria currently specified by SQN TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are non-conservative. A Condition Report (CR) was initiated in accordance with the TVA Corrective Action Program. Subsequently, a prompt determination of operability (PDO),

including administrative controls were established in accordance with the Nuclear Regulatory Commission (NRC) Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998. As a result of the CR, a number of immediate/interim and other corrective actions were identified, implemented, and completed. A review of historical DG test records for frequency and voltage supported the fact that the DGs were operable and supported the existing design basis analyses accidents. Administrative controls for DG frequency have been implemented in the applicable Surveillance Instructions to support continued DG operability.

U.S. Nuclear Regulatory Commission CNL-16-001 Page 2 May 26, 2016 The enclosure to this letter provides a description of the proposed changes, technical evaluation of the proposed changes, regulatory evaluation, and a discussion of environmental considerations. Attachments 1 and 2 to the enclosure provide the existing TS and Bases pages marked-up to show the proposed changes. Attachments 3 and 4 to the enclosure provide the existing TS and Bases pages retyped to show the proposed changes. Changes to the existing TS Bases, are provided for information only and will be implemented under the Technical Specification Bases Control Program.

As noted in the enclosure, the modified SR 3.8.1.9 is normally performed during outages.

Therefore, TVA requests NRC approval of this proposed license amendment by May 2017 with implementation during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy the revised SR 3.8.1.9 prior to implementation of this proposed license amendment.

TVA has determined that there are no significant hazard considerations associated with the proposed change and that the change qualifies for a categorical exclusion from environmental review pursuant to the provisions of 10 CFR 51 .22(c)(9).

The SQN Plant Operations Review Committee and the TVA Nuclear Safety Review Board have reviewed this proposed change and determined that operation of SQN Units 1 and 2 in accordance with the proposed change will not endanger the health and safety of the public.

In accordance with 10 CFR 50.91(b)(1), TVA is sending a copy of this letter and the enclosure to the Tennessee Department of Environment and Conservation.

There are no new regulatory commitments associated with this submittal. Please address any questions regarding this request to Ed Schrull at (423) 751-3850.

I declare under penalty of perjury that the foregoing is true and correct. Executed on this 26th day of May 2016.

President, Nuclear Licensing Enclosure cc: See Page 3

U.S. Nuclear Regulatory Commission CNL-16-001 Page 3 May 26, 2016 RDW: EDS

Enclosure:

Evaluation of Proposed Change cc (Enclosure):

NRC Regional Administrator - Region II NRC Senior Resident Inspector - Sequoyah Nuclear Plant NRR Project Manager - Sequoyah Nuclear Plant Director, Division of Radiological Health - Tennessee State Department of Environment and Conservation

ENCLOSURE TENNESSEE VALLEY AUTHORITY SEQUOYAH NUCLEAR PLANT UNITS 1 AND 2 EVALUATION OF PROPOSED CHANGE

Subject:

Application to Modify Sequoyah Nuclear Plant Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02) 1.0

SUMMARY

DESCRIPTION 2.0 DETAILED DESCRIPTION 2.1 Proposed Change 2.2 Need for Proposed Changes 2.3 Implementation

3.0 TECHNICAL EVALUATION

3.1 System Description 3.2 Evaluation 3.3 Conclusion

4.0 REGULATORY EVALUATION

4.1 Applicable Regulatory Requirements and Criteria 4.2 Precedent 4.3 Significant Hazards Consideration 4.4 Conclusion

5.0 ENVIRONMENTAL CONSIDERATION

6.0 REFERENCES

ATTACHMENTS

1. Proposed TS Changes (Mark-Ups) for SQN Units 1 and 2
2. Proposed TS Bases Changes (Mark-Ups) for SQN Units 1 and 2 (For Information Only)
3. Proposed TS Changes (Final Typed) for SQN Units 1 and 2
4. Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)

CNL-16-001 E1 of 20

ENCLOSURE 1.0

SUMMARY

DESCRIPTION The Tennessee Valley Authority (TVA) is requesting a license amendment to amend the Sequoyah Nuclear Plant (SQN) Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in SQN Units 1 and 2, TS 3.8.1, "AC Sources - Operating. Specifically, the proposed change and supporting evaluation will modify the acceptance criteria for the DG steady state frequency range provided in SQN Units 1 and 2 TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18.

Currently, the DG SR steady state acceptance criteria are 58.8 Hz and 61.2 Hz.

TVA proposes to change the SQN DG steady state frequency acceptance criteria to 59.8 Hz and 60.2 Hz. The DG TS SR steady state voltage range of 6800 V and 7260 V is not affected. This license amendment request (LAR) is similar to a Watts Bar Nuclear Plant (WBN) Unit 1 submittal (Reference 1), which was approved by the NRC in Reference 2.

This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed.

However, no specific changes to SR 3.8.1.3 or TS 3.8.2 are required.

2.0 DETAILED DESCRIPTION 2.1 Proposed Changes Currently, the acceptance criteria for DG steady state frequency specified in SQN Units 1 and 2, TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are 58.8 Hz and 61.2 Hz. TVA proposes to conservatively narrow the DG frequency range by increasing the current DG frequency lower limit of 58.8 Hz to 59.8 Hz and decreasing the current upper limit from the existing 61.2 Hz to 60.2 Hz in the SQN Units 1 and 2 TS1 (i.e., SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18) and TS Bases 3.8.1. The proposed SQN Units 1 and 2 DG frequency and voltage steady state operating ranges only apply to the steady state condition of DG operation, and are summarized below in Table 1.

Table 1 Technical Specification DG Steady-State Operating Range Parameter Range Frequency 59.8 Hz to 60.2 Hz Voltage 6800 V to 7260 V This change is applicable to the surveillances performed at 31 days, 18 months, and ten years when maintenance & test equipment (M&TE) is installed on the DG per the surveillance instructions.

1 Note: No change is required to SQN Units 1 and 2, TS SR 3.8.1.19 because that surveillance does not apply to steady state operation.

CNL-16-001 E2 of 20

ENCLOSURE The DG voltage limits as described in the Technical Specifications are correct and do not require revision.

Attachments 1 and 2 to this enclosure provide the existing SQN Units 1 and 2 TS and Bases pages marked-up to show the proposed changes. Attachments 3 and 4 to this enclosure provide the clean typed TS and Bases pages with the proposed changes incorporated.

The proposed Bases changes are provided to the NRC for information only.

2.2 Need for Proposed Changes Plant safety analyses make specific assumptions regarding the emergency core cooling system (ECCS) flow to provide the core cooling function following any event that requires safety injection (SI) to mitigate the event. For the events that assume a loss of offsite power (LOOP), the DGs provide power to the ECCS pumps. Following a LOOP, each DG starts and ties to an engineered safety feature (ESF) board, and essential loads, including the ECCS pumps, are sequentially connected to the ESF board by individual timers for each load sequence. The calculated ECCS flow rates assume that the steady state DG frequency is 60 Hz (i.e., after the DG starting and loading transients).

Once the DG starting and loading sequences are complete, the DG governor maintains the frequency at 60 Hz within a specified tolerance, which is based on the governor manufacturer/model.

The ECCS flow provided by the ECCS pumps is affected by the pump speed, which in turn is a function of the DG frequency. Historically, the DG frequency tolerances associated with the governor were not considered in the development of the ECCS, containment spray system (CSS), and auxiliary feedwater (AFW) flow rates. The primary effect of changes in DG frequency on the ECCS safety functions is an increase or decrease in the speed of safety-related motors that are powered by the DG. The increase or decrease in the speed of the motors affects pump performance, motor operated valve (MOV) stroke times, cooling fan performance, and DG loading, among other factors.

The minimum and maximum frequency values of 58.8 Hz and 61.2 Hz in the SQN TS SRs are equal to +/- 2% of the 60 Hz nominal frequency (i.e., the TS specified plant specific transient range). However, the +/- 2% frequency tolerance is only applicable to DG starting and loading transients, and does not apply to steady state operation as discussed in Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies" (Reference 3).

Because the safety analyses did not consider the effects of operating at the extremes of the steady state frequency range specified in TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18, TVA has determined that the current SQN Units 1 and 2 TS SR acceptance criteria for steady state DG frequency are non-conservative. The non-conservative acceptance criteria were addressed within the TVA corrective action program (CAP) and administrative controls were established in accordance with NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety" (Reference 4). To address the non-conservative TS, CNL-16-001 E3 of 20

ENCLOSURE TVA is proposing a change to TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 to revise the DG SR steady state acceptance criteria to 59.8 Hz and 60.2 Hz.

The four SQN DGs are shared between SQN Units 1 and 2, as described in Section 3.1, and the SRs for all four DGs are specified in the SQN Units 1 and 2 TSs. Therefore, the proposed SR steady state frequency acceptance criteria of 59.8 Hz and 60.2 Hz would apply to all four DGs.

2.3 Implementation The TVA process governing the preparation and submittal of TS changes and LARs requires that the appropriate organizations (e.g., Operations, Training, Engineering, Maintenance, Chemistry, Radiation Protection, and Work Control) identify the documents that are affected by each proposed change to the TSs and Operating Licenses. Among the items that are considered are training, plant modifications, procedures, special implementation constraints, design documents, and surveillance instructions associated with TS SRs, Technical Requirements Manual, TS Bases, and the Updated Final Safety Analysis Report (UFSAR). The process requires that procedures and design document changes necessary to support TS Operability are approved prior to implementation of an NRC approved license amendment. The process also provides assurance that the remaining changes, if any, are scheduled and tracked for configuration control.

SR 3.8.1.9 requires verification that each DG can maintain acceptable frequency following a load rejection greater than or equal to the single largest post-accident load.

This SR includes verification that the DG can restore frequency within the allowable steady-state band within three seconds. SQN currently performs SR 3.8.1.9 concurrent with SR 3.8.1.10, which verifies that the DG can withstand a full load rejection (from a fully loaded condition). This approach is acceptable because the full load rejection of SR 3.8.1.10 as well as the single largest post-accident load requirement of SR 3.8.1.9 are performed. The current test methodology for both SR 3.8.1.9 and 3.8.1.10 requires the DG to initially be in parallel with offsite power to achieve the required power value.

When the DG is operating in parallel with offsite power for surveillance testing, the speed droop circuit in the DG speed governor is required to be in service (i.e., non-emergency /

droop test mode). The speed droop function is necessary to ensure stable and controllable load-sharing between the DG and offsite power. However, the speed droop results in a steady-state frequency greater than the nominal 60 Hz value following a load rejection. Historical data shows that DG frequency typically stabilizes at approximately 60.3 Hz following a single largest load rejection with speed droop in service. This final frequency value is acceptable under the current SR 3.8.1.9, but is outside the more stringent frequency criteria proposed in this LAR. These results are due to the surveillance test methodology (i.e., performing the load rejection with the speed droop circuit in service) rather than being an indication of a problem or malfunction in the DG speed governor.

CNL-16-001 E4 of 20

ENCLOSURE To successfully perform SR 3.8.1.9 with the more conservative frequency band proposed in this LAR, the test methodology must be modified to perform the load rejection with the DG in accident mode (emergency / isochronous mode) and isolated on the shutdown board (i.e., not initially in parallel with offsite power). In the accident mode, the DG speed governor uses a fixed speed reference corresponding to 60.0 Hz, which ensures that the frequency criteria of SR 3.8.1.9 can be met. This requires a revision to the surveillance test procedures to perform SR 3.8.1.9 in conjunction with SR 3.8.1.18 (shutdown board blackout testing). This change in methodology is beneficial because it more closely replicates the conditions under which the DGs may have to perform following a loss of offsite power. TVA has initiated action to ensure that the applicable surveillance testing procedures are revised to incorporate this change prior to the next unit refueling outage on each SQN unit. Because the modified SR 3.8.1.9 is normally performed during outages, TVA is requesting implementation of this proposed license amendment during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy revised SR 3.8.1.9 prior to implementation of this proposed license amendment.

3.0 TECHNICAL EVALUATION

3.1 System Description The onsite Class 1E alternating current (AC) standby system is described in SQN UFSAR Section 8.3, "Onsite Power System.

As noted in SQN UFSAR Section 8.3, the onsite AC power system is a Class 1E system, which consists of the standby AC power system and the 120 V vital AC system. The standby AC power system is a safety-related system, which supplies power for energizing all AC-powered electrical devices essential to safety. The safety function of the standby AC power system is to supply power to permit functioning of components and systems required to assure that: (1) fuel design limits and reactor coolant pressure boundary design conditions are not exceeded due to anticipated operational occurrences, and (2) the core is cooled and vital functions are maintained in the event of a postulated accident, subject to loss of the preferred power system and subject to any single failure in the standby power system.

Specifically, the standby AC power system includes:

  • four 6.9 kV shutdown boards and logic relay panels
  • associated 6.9 kV/480 V transformers and 480 V shutdown boards
  • motor control centers supplied by the 480 V shutdown boards The AC standby power system is divided into two redundant load groups (power trains).

The 6.9 kV shutdown boards are arranged electrically into two power trains with two boards associated with each train and each unit. The boards comprising train A are located in the SQN Unit 1 side and those of train B are located in the SQN Unit 2 side.

The train A boards are separated from the train B boards by a reinforced concrete block wall, which is a qualified fire barrier, extended to the ceiling. When the preferred (offsite) power system is not available, each shutdown board is energized from a separate standby DG.

CNL-16-001 E5 of 20

ENCLOSURE A loss of voltage on the 6.9 kV shutdown board starts the associated DG and initiates logic that trips the supply feeder breakers, all 6.9 kV loads (except the 480 V shutdown board transformers), and the major 480 V loads. The bypass breaker for the 480 V shutdown boards current-limiting inductive reactor is also closed as part of this logic.

When the DG has reached rated speed and voltage, the generator is automatically connected to the 6.9 kV shutdown board. This return of voltage to the 6.9 kV shutdown board initiates logic that connects the required loads in sequence. The standby (onsite) power system's automatic sequencing logic is designed to automatically connect the required loads in proper sequence should the logic receive an accident signal prior to, concurrent with, or following a loss of all nuclear unit and preferred (offsite) power.

As noted in UFSAR Section 8.3.1.1, there are two loading sequences:

One, which is applied in the absence of a safety injection signal (SIS), the non-accident condition, and the other accident condition, applied when an SIS (and containment spray actuation signal) is received coincident with a sustained loss of voltage on the 6.9 kV shutdown board.

A loss of offsite power coincident with an SIS is the design basis event; however, as noted in UFSAR Section 8.3.1.1, an SIS received during the course of a non-accident shutdown loading sequence would cause the actions described below.

1. Loads already sequentially connected that are not required for an accident will be disconnected (except fire pumps powered by the DG).
2. Loads already sequentially connected that are required for an accident will remain connected.
3. Loads pending sequential loading that are not required for an accident will not be connected.
4. Loads awaiting sequential loading that are required for an accident will have their sequential timers reset to time zero from which they will then be sequentially loaded.

An SIS received in the absence of a sustained loss of voltage on a 6.9 kV shutdown board would start the DGs, but would not connect them to the shutdown boards.

Each DG consists of two 16-cylinder engines directly connected to a 6.9 kV generator.

The continuous rating of each DG is 4400 kilowatt (kW) at 0.8 power factor, 6.9 kV, 3-phase, and 60 Hz. Each DG also has an additional rating of 4840 kW for 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> out of 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />.

Ratings for the DGs satisfy the requirements of Regulatory Guide 1.9 as clarified in Section 4.1. The continuous service rating of each DG is 4400 kW with 10% overload permissible for up to 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> in any 24 hour2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> period.

The normal operating speed of the DGs is 900 rpm. The DGs use a tandem arrangement; that is, each DG consists of two diesel engines with a generator between them connected together to form a common shaft. The DGs are physically separated, electrically isolated from each other, and protected from the probable maximum flood.

CNL-16-001 E6 of 20

ENCLOSURE The DGs are equipped with Woodward governors and consist of:

  • an EGB-13P actuator on each engine
  • a 2301A computer (reverse biased)
  • a magnetic speed pickup The Woodward EGB-13P actuator used with the 2301A computer is a proportional governor that moves the fuel rack in inverse proportion to the voltage signal from the computer. There is a governor actuator on each DG engine and they are electrically connected in series so that the loss of signal to one actuator would also result in the loss of signal to the other actuator. Based upon the input from the magnetic speed pickup, the electronic governor sends electric signals to the actuators on the two DG engines.

This signal goes to the coils of each actuator that are connected in series so that each coil receives the same electric signal. The terminal shaft of each actuator will move the same amount for each change in signal, thus the fuel control shaft movement on each DG engine will be identical.

The steady state speed control will be within 0.25 percent of rated speed. The governor design includes circuits to provide high- and low-limit adjustments. These limits set the maximum and minimum speed that can be set by varying the speed-setting milliamp or voltage reference. The low limit can be set as high as rated speed, if desired, eliminating the ability of the process or controller speed setting to reduce speed. The SQN Units 1 and 2 DG electrical governor is set within a speed band that is equivalent to a DG frequency of 59.95 Hz +/- 0.05 Hz.

The SQN Units 1 and 2 DG voltage and frequency regulators were evaluated to ensure they were capable of meeting the TS and associated SRs. The measured values for both voltage and frequency have not exhibited drift and have been consistently within the respective setting band.

The SQN Units 1 and 2 DG voltage regulators and speed regulators are independent devices that are not expected to exhibit drift. This has been demonstrated by the past history of diesel surveillances in which the diesel is operated in isochronous mode. If the two variables drift in different directions (e.g., frequency lower and voltage higher), the combined effect on pump speed would be less than an individual drift.

Based on this independence and stability, the composite impact of frequency and voltage were evaluated independently for the Technical Specification band. The frequency range was analyzed over the full range (i.e., 59.8 Hz to 60.2 Hz) within the voltage setting range (i.e., 6925 V to 7000 V). Likewise, the voltage (i.e., 6800 V to 7260 V) was analyzed over the full range within the frequency range of 59.8 Hz to 60.2 Hz.

Test equipment verifies that the governor controls the DG frequency within the steady-state operational band of 59.8 Hz to 60.2 Hz.

The DGs, as clarified in Section 4.1, satisfy the requirements of Regulatory Guide (RG) 1.9, Revision 0 (Reference 3) and RG 1.9, Revision 1 (Reference 5).

CNL-16-001 E7 of 20

ENCLOSURE 3.2 Evaluation 3.2.1 Introduction Calculations were conducted to determine the effects of the DG frequency variation between 59.8 Hz and 60.2 Hz on plant equipment fed by the DGs following a loss of offsite power (LOOP) or a loss of coolant accident (LOCA) coincident with a LOOP.

The changes in the DG frequency have the direct effect of changing motor speeds for the motors fed from the generators following a LOOP or a LOOP/LOCA. The changes in motor speeds are addressed in Section 3.2.2 and affect the following components:

  • Pumps and Fans (Section 3.2.3)
  • Air compressors and chillers (Section 3.2.4)
  • Motor operated valves (MOVs) (Section 3.2.5)
  • Electrical Equipment (Section 3.2.6)

The changes in these parameters were evaluated to demonstrate that the subject equipment would continue to meet their safety related functions within the analyzed bounds documented in design documents. In addition, the increased horsepower associated with increased frequency was evaluated to ensure that the horsepower increases do not result in exceeding the sustained load ratings for the DGs and the decreased flowrate associated with the revised frequency range was evaluated to ensure pump parameters are adequate. Battery chargers and power transformers do not have motors, but frequency changes were examined to determine if the chargers and transformers would provide acceptable output parameters to continue to meet the specifications and requirements of the downstream components.

The results of these calculations are provided below.

3.2.2 Comparison of Voltage and Frequency Impact Motor speed change, as a function of torque (Reference 6), is:

S = (/N1)(SsynS) where, S = speed change Ssyn = motor synch speed S = motor speed

= original torque N = the new torque The motor speed is directly affected by the frequency. The affected components, listed in Section 3.2.1, are either designed for 6600 V operation with the supply boards rated at 6900 V, or designed for 460 V operation with the supply boards rated CNL-16-001 E8 of 20

ENCLOSURE at 480 V. Therefore, during normal operation, the motors see a voltage higher than their nominal rating. Thus, for the lower voltage limit of 6800 V (473 V on the low voltage side), the motors still have their minimum voltage and produce their design torque. Therefore, a low voltage condition is a non-bounding condition and was not further evaluated. For the high voltage case, the motors could have a voltage of 7260 V (505 V on the low voltage side) or 10 percent above the motor design nominal rating, neglecting any voltage drop from the DG to the motor.

Because the torque developed by a motor is directly proportional to the square of the terminal voltage, the above equation is rewritten in terms of voltage, as follows:

S = [(V/VN)21]*(SsynS) where, S = speed change (SsynS) = motor slip, < 2 percent (the value of 2 percent is based on a review of vendor manuals which demonstrates that the motors have < 2 percent slip)

V = Nominal voltage, 6600 V VN = New voltage, 7260 V S = [(6600/7260)21]*(2 percent)

S = -0.35 percent Thus, with a motor slip of less than 2 percent, the motor speed impact is less than 0.35 percent due to the voltage increase to 7260 V from design voltage of 6600 V.

The frequency shift could result in a + 0.35 percent motor speed and the voltage could result in +0.35 percent motor speed change. Therefore, a speed impact of

+ 0.35 percent was used as the DG frequency impact for analyzing the effect caused either by frequency or voltage variation on the affected components in the following sections.

3.2.3 Effect on Pumps 3.2.3.1 Pump Net Positive Suction Head (NPSH)

The change in the DG frequency was evaluated for the effect on the NPSH available to the following emergency core cooling system (ECCS) pumps. These pumps are fed from the DGs; therefore, they could be affected by the variation in frequency of 59.8 Hz to 60.2 Hz:

  • Safety injection (SI)
  • Centrifugal charging (CC)

An evaluation was performed to determine if the NPSH available (NPSHA) exceeds the NPSH required (NPSHR) for the RHR and the CS pumps while taking suction from the containment sump (recirculation mode). The evaluation also determined CNL-16-001 E9 of 20

ENCLOSURE the NPSH Margin for the CS, SI, RHR, and CC pumps during injection mode operation with suction taken from the refueling water storage tank (RWST). Only the injection mode is presented, as the injection mode has less NPSH margin than the recirculation mode.

3.2.3.1.1 Pump Flow Rates DG frequency affects both the head and flow values based on the pump affinity laws as follows:

Q2 = (N2IN1)*Q1 where, Q2 = Changed pump flow due to DG frequency variation Q1 = Nominal pump flow N2 = Changed pump speed due to DG frequency variation N1 = Nominal pump speed For the 59.8 Hz frequency, Q2 = (59.8/60.0)*Q1 = 0.997*Q1 For the 60.2 Hz frequency, Q2 = (60.2/60.0)*Q1 = 1.003*Q1 Therefore, a 0.2Hz change in DG frequency will change pump flow by + 0.33%.

3.2.3.1.2 NPSH The NPSHR for pumps increases as the speed and flowrate increase. The NPSHR is also affected by the increase in DG frequency as follows:

NPSHR2 = (N2Q2)4/3*NPSHR1 (N1Q1)4/3 Table 2 presents examples of NPSHR changes resulting from the DG frequency changes for the various pumps.

The results in Table 3 demonstrate the actual flow rates, NPSHA, NPSHR, and the NPSH Margin for the various pumps. The NPSHR values were obtained from the pump manufacturers NPSH curves at the flow values that are listed in Table 3. The DG increased frequency effects are included in these values. The results demonstrate that there is adequate positive margin for the pumps with the DG operating at the proposed revised frequencies.

CNL-16-001 E10 of 20

ENCLOSURE Table 2 Example NPSHR Changes System CS CC SI RHR NPSHR (ft) current 12.5 22 37.5 16 NPSHR (ft) at 12.6 22.1 37.8 16.1 60.2 Hz Table 3 NPSH Margin While Operating in RWST Injection Mode with Revised DG Frequency System CS CC SI RHR Pump Number A-A B-B A-A B-B A-A B-B A-A B-B Increased Pump 5100 5100 450 450 500 500 4200 4200 Flow (sgpm)

Pump Suction P 3.8 -2.5 6.7 6.8 1.9 1.6 -1.6 -3.9 (psig)

Pump Suction P 18.2 11.9 21.1 21.2 16.3 16.0 12.8 10.5 (psia)

Vapor P at 105°F 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 (psia)

NPSHA (psi) 17.1 10.8 20 20.1 15.2 14.9 11.7 9.4 NPSHA (ft) 39.7 25.1 46.5 46.7 35.3 34.6 27.2 21.8 NPSHR (ft) 12.1 12.1 18 18 19 19 15 15 NPSH margin (ft) 27.6 13 28.5 28.7 16.3 15.6 12.2 6.8 3.2.3.2 Pump Test Points The DG frequency variation of 59.8 Hz to 60.2 Hz has a negligible effect on plant operations for the above affected pumps based on the revised flow rates in Section 3.2.3.1. The flow change resulting from the DG frequency variation is limited to + 0.35%. The pump test acceptance criteria upper limit will be adjusted downward, and the lower limit will be adjusted upward in order to encompass the potential flow variation. The ASME OM Code inservice pump testing acceptance criteria provide assurance that the design basis is met.

3.2.3.3 Effect on Fans DG frequencies above/below 60 Hz directly increase/reduce motor speeds for fans.

Fan speed is directly proportional to fan flow. Therefore, increased/reduced motor speed will result in increased/reduced flows. For the 60.2 Hz DG frequency, fan flows are impacted as follows:

CNL-16-001 E11 of 20

ENCLOSURE Q2 = (60.2/60.0)*Q1 = 1.0033*Q1 and for the 59.8 Hz DG frequency, fan flows are impacted as follows; Q2 = (59.8/60.0)*Q1 = 0.9967*Q1 where:

Q2 = Changed fan flow due to DG frequency variation Q1 = Nominal fan flow From the above equations, fan flow could vary from nominal to about +0.33%. From the G-Spec (Reference 7), total airflow of a system can vary by +10% at the system fan. Thus, fan flows are within allowed tolerances due to sustained DG frequency variations.

3.2.3.4 Effect on Horsepower Requirements Horsepower requirements for a pump motor and fan increase by the cube of the speed change. Therefore, increased motor speed will result in increased horsepower demands on the diesels that feed the subject loads. The potential increase in load on the DGs due to operating frequency and voltage was evaluated to 60.2 Hz and 7260 V. The highest steady state loading was used which envelopes the other steady state loading scenarios.

Motor slip is defined as the difference between actual speed and synchronous speed an induction machine operates at as a percentage of the synchronous speed. A motor slip of about one percent increase in speed was calculated based on the increased DG voltage.

Motor speed varies directly with the system frequency as shown below:

1/2 = f1/f2 Thus, the speed impact of the frequency variation is (60 + 0.2)/60 or + 0.33%.

Therefore, the total impact of the voltage and frequency shift would be the sum of 1% + 0.33% which equals a 1.33% increase in motor speed.

As noted above, motor horsepower varies directly with the cube of the motor speed:

LoadNew = Loadold *Speed3 LoadNew = LoadOld

  • 1.01333 = LoadOld *1.040 Therefore, DG load would be increased by 4% if both the voltage and frequency were at their upper limits of 7260 V and 60.2 Hz. Because the DG fuel oil consumption is analyzed for a fully loaded diesel, the voltage and frequency variation do not adversely affect the fuel oil analysis.

CNL-16-001 E12 of 20

ENCLOSURE 3.2.4 Effect on Air Compressors and Chillers Air compressors and chillers are intermittently operated equipment designed to maintain an asset or volume between selected setpoints. Air compressors cycle on to charge a system to a high pressure setpoint, and then cycle off until the header pressure drops below the specified setpoint. Chillers cycle on and off to maintain a refrigerant fluid temperature between a specified range of temperatures. Because both air compressors and chillers work intermittently to maintain a fluid media in a range between two setpoints, the approximate +0.33% (+0.2 Hz) variation in DG frequency has a negligible effect on this type of equipment.

3.2.5 Effect on MOVs The affected MOVs were evaluated for frequency and voltage related to DG loading.

Motor torque and stroke time are two important parameters associated with MOV performance. The DG frequency affects the motor torque (Section 3.2.2) and speed.

Valve stroke time is inversely proportional to motor speed. Therefore, faster/slower motor speed would result in shorter/longer valve stroke times. For the 60.2 Hz frequency, valve stroke times vary as follows:

T2 = (60.2/60.0)*T1 = 1.0033*T1 Equation (1) and for the 59.8 to 60.0 Hz DG frequency range, valve stroke times are affected as follows; T2 = (59.8/60.0)*T1 = 0.9967*T1 Equation (2) where:

T2 = Changed stroke time due to DG frequency variation T1 = Nominal stroke time From equations (1) and (2), valve stroke times vary from nominal to approximately

+0.33%. For example, a valve that strokes in 30 seconds has the potential variation in stroke time of approximately +0.1 seconds. This potential variation is small in comparison to the valve stroke times documented in the inservice testing program and is essentially the same as the recorded resolution of the stop watches used for valve stroke time testing (i.e., 0.1 seconds). The majority of the active safety related MOVs stroke in 10 seconds or less; therefore, the variance in stroke time is

+ 0.03 seconds. For a 10-second valve, this is below the detectible threshold of the normal timing method. The longest of the safety related valve stroke times is up to 120 seconds for the valves involved in the automatic containment sump swap over.

The time variation is about + 0.4 seconds for these valves.

The MOV stroke time acceptance criteria for the ASME OM Code testing are adjusted to include the potential low frequency power. Accordingly, the design basis requirements for valve stroke time will be met. The minimum allowable DG voltage provides a voltage that is greater than the voltage used for the Generic Letter 89-10 analysis.

CNL-16-001 E13 of 20

ENCLOSURE Furthermore, based on the analyses in Section 3.2.2, the impact to torque is acceptable. In addition, there would not be a concern for water hammer due to the small change in stroke time. Therefore, there are no concerns with MOV operation due to the variation in DG frequency and voltage.

3.2.6 Effect on Electrical Equipment Most static loads are insensitive to changes in frequency and have a directly proportional change in current with terminal voltage, which is the opposite of the effects of voltage variation on induction motors. Only electronically controlled equipment, such as battery chargers, inverters and uninterruptible power supplies may be of concern at off nominal line frequency. The maximum allowable board voltage is 7260 V and the degraded voltage relay safety limit dropout setting is 6400 V. The variation in voltage from the DG of 6800 to 7260 V is much less than the range expected from the offsite source. Therefore, the variation in DG output voltage is bounded by voltage variations when off site power supplies the AC auxiliary power system.

3.2.6.1 Battery Chargers The battery charger regulation is maintained at +/-1% from no-load to full load with simultaneous changes in AC line voltage of +10% / -15% and changes in AC line frequency of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the battery chargers.

3.2.6.2 Hydrogen Igniters The hydrogen mitigation system (i.e., H2 igniters) does not use frequency sensitive components with the exception of the regulating transformer. The output is regulated to +/-1% from no-load to full load with AC line voltage changes of +/-10% and changes in AC frequency changes of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the hydrogen mitigation system.

3.2.6.3 Instrumentation 120 V AC instrumentation circuits are designed with a +/-1% variation in frequency.

The variation in DG frequency is within this range.

3.3 Conclusion The results of these calculations determined that the proposed change in the DG frequency does not adversely affect the equipment powered by the DGs and their associated components described above. The calculations are available for NRC review. The DG output voltage and frequency range of 6800 to 7260 V and 59.8 to 60.2 Hz, respectively, will not affect the miscellaneous electrical equipment required to mitigate design basis events.

CNL-16-001 E14 of 20

ENCLOSURE

4.0 REGULATORY EVALUATION

4.1 Applicable Regulatory Requirements and Criteria The onsite standby ac power systems at SQN Units 1 and 2 are designed to comply with the following applicable regulations and requirements.

  • Title 10 of the Code of Federal Regulations (10 CFR) Part 50 (10 CFR 50),

Appendix A, General Design Criterion (GDC) 17, "Electric power systems," specifies that an onsite electric power system shall be provided to permit functioning of structures, systems, and components important to safety.

specifies that electric power systems important to safety shall be designed to permit appropriate periodic inspection and testing of important areas and features.

  • Regulatory Guide 1.6, Revision 0 (Reference 8), "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems," describes an acceptable degree of independence between redundant standby (onsite) power sources and between their distribution systems.
  • Regulatory Guide 1.9, Revision 0 (Reference 3). As noted in SQN UFSAR Section 8.3.1.2.1, SQN Units 1 and 2 comply with Regulatory Guide 1.9, Revision 0 except that voltage and frequency recovery requirements are taken from Regulatory Guide 1.9, Revision 1. As further noted in SQN UFSAR Section 8.3.1.2.1, an exception is taken for frequency immediately following DG breaker closure. The DG breaker is designed to automatically close at about 94 percent of nominal frequency.

This exception was accepted by the NRC in NUREG-1232 Volume 2 (Reference 9).

  • IEEE Standard 308-1971, "Criteria for Class 1E Power Systems for Nuclear Power Generating Stations," provides criteria for the determination of Class 1E power system design features and the requirements for their testing, surveillance, and documentation.

With the implementation of the proposed change, SQN Units 1 and 2 continues to meet the applicable regulations and requirements, subject to the previously approved exceptions.

4.2 Precedent The NRC has previously approved changes revising the TS SR acceptance criteria for steady state DG frequency.

1. Amendment Number 102 was issued for WBN Unit 1 in the Safety Evaluation dated September 17, 2015 (Reference 2). The Amendment made changes similar to those in this proposed license amendment request in that it revised the DG SR steady state frequency from 58.8 Hz and 61.2 Hz to 59.8 Hz and 60.1 Hz.
2. Amendment Numbers 227 and 105 were issued for Beaver Valley Power Station, Units 1 and 2, respectively, in the Safety Evaluation dated February 11, 2000 CNL-16-001 E15 of 20

ENCLOSURE (Reference 10). The Amendment corrected non-conservative TSs by clarifying the fuel oil storage volume requirements, increasing the load requirement for the single largest load rejection test, establishing criteria for maximum frequency that should not be exceeded following a load rejection, and revising the DG SR steady state frequency to 60.0 Hz and 60.6 Hz for Units 1 and 2 and 59.9 Hz and 60.3 Hz for Unit 2.

3. Amendment Number 129 was issued for the Palo Verde Nuclear Generating Station, Units 1, 2, and 3, in the Safety Evaluation dated October 4, 2000 (Reference 11).

The Amendment corrected non-conservative TSs by revising the current steady-state DG voltage limits of 3740 V and 4580 V and steady state frequency limit of 59.7 Hz and 61.2 Hz to a steady state voltage of 4000 V and <4377.2 V, and steady state frequency of 59.7 Hz and 60.7 Hz for the affected SR, except that for SR 3.8.1.2, the lower frequency limit is 58.8 Hz instead of the 59.7 Hz.

4. Amendment Numbers 309 and 291 were issued for the Donald C. Cook Nuclear Plant, Units 1 and 2, respectively, in the Safety Evaluation dated April 30, 2009 (Reference 12). The Amendment corrected non-conservative TSs by reducing the maximum DG steady state frequency in the associated SRs from 61.2 Hz to 60.5 Hz.

The Amendment also revised the minimum steady state voltage from 3740 V to 3910 V for certain TS SRs for consistency with the minimum steady state voltage specified in the acceptance criteria for other TS SRs, and reduced the criteria for maximum frequency that should not be exceeded following a load rejection.

5. Amendment Number 236 was issued for Crystal River, Unit 3 in the Safety Evaluation dated December 10, 2009 (Reference 13). The Amendment corrected non-conservative TSs by revising the DG steady state voltage to 4077 V and 4243 V and DG steady state frequency to 59.4 Hz and 60.6 Hz.
6. Amendment 204 was issued for the Wolf Creek Generating Station in the Safety Evaluation dated April 11, 2013 (Reference 14). The Amendment corrected non-conservative TSs by revising minimum DG steady state voltage to 3950 V and DG steady state frequency to 59.4 Hz and 60.6 Hz. The Amendment also revised the DG loading requirements to reflect the results of updated calculations.

4.3 Significant Hazards Consideration The proposed change would modify the Sequoyah Nuclear Plant (SQN), Units 1 and 2, Technical Specification (TS) 3.8.1, "AC Sources - Operating," by revising the acceptance criteria for the diesel generator (DG) steady state frequency acceptance criteria specified in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. The frequency will be changed from 58.8 Hz and 61.2 Hz to 59.8 Hz and 60.2 Hz for SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18.

This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed.

CNL-16-001 E16 of 20

ENCLOSURE TVA has evaluated whether or not a significant hazards consideration is involved with the proposed amendment(s) by focusing on the three standards set forth in 10 CFR 50.92, Issuance of amendment, as discussed below:

1. Does the proposed amendment involve a significant increase in the probability or consequence of an accident previously evaluated?

Response: No The DGs are required to be operable in the event of a design basis accident coincident with a loss of offsite power to mitigate the consequences of the accident. The DGs are not accident initiators and therefore these changes do not involve a significant increase in the probability of an accident previously evaluated.

The accident analyses assume that at least the boards in one load group are provided with power either from the offsite circuits or the DGs. The change proposed in this license amendment request will continue to assure that the DGs have the capacity and capability to assume their maximum design basis accident loads. The proposed change does not significantly alter how the plant would mitigate an accident previously evaluated.

The proposed change does not adversely affect accident initiators or precursors nor alter the design assumptions, conditions, and configuration of the facility or the manner in which the plant is operated and maintained. The proposed change does not adversely affect the ability of structures, systems, and components (SSC) to perform their intended safety function to mitigate the consequences of an initiating event within the assumed acceptance limits. The proposed change does not affect the source term, containment isolation, or radiological release assumptions used in evaluating the radiological consequences of any accident previously evaluated. Further, the proposed change does not increase the types and amounts of radioactive effluent that may be released offsite, nor significantly increase individual or cumulative occupational/public radiation exposure.

Therefore, the proposed change does not involve a significant increase in the probability or consequences of an accident previously evaluated.

2. Does the proposed amendment create the possibility of a new or different kind of accident from any accident previously evaluated?

Response: No.

The proposed change does not involve a change in the plant design, system operation, or the use of the DGs. The proposed change requires the DGs to meet SR acceptance criteria that envelope the actual demand requirements for the DGs during design basis conditions. These revised acceptance criteria continue to demonstrate the capability and capacity of the DGs to perform their required functions. There are no new failure modes or mechanisms created due to testing the DGs within the proposed acceptance criteria. Testing of the DGs at the proposed acceptance criteria does not involve any modification in the CNL-16-001 E17 of 20

ENCLOSURE operational limits or physical design of plant systems. There are no new accident precursors generated due to the proposed test loadings.

Therefore, the proposed change does not create the possibility of a new or different kind of accident from any accident previously evaluated.

3. Does the proposed amendment involve a significant reduction in a margin of safety?

Response: No.

The proposed change will continue to demonstrate that the DGs meet the TS definition of operability, that is, the proposed acceptance criteria will continue to demonstrate that the DGs will perform their safety function. The proposed testing will also continue to demonstrate the capability and capacity of the DGs to supply their required loads for mitigating a design basis accident.

The proposed change does not alter the manner in which safety limits, limiting safety system settings or limiting conditions for operation are determined. The safety analysis acceptance criteria are not affected by this change. The proposed change will not result in plant operation in a configuration outside the design basis.

Therefore, the proposed change does not involve a significant reduction in a margin of safety.

Based on the above, TVA concludes that the proposed amendment does not involve a significant hazards consideration under the standards set forth in 10 CFR 50.92 (c), and, accordingly, a finding of no significant hazards consideration is justified.

4.4 Conclusion In conclusion, based on the considerations discussed above, (1) there is reasonable assurance that the health and safety of the public will not be endangered by operation in the proposed manner, (2) such activities will be conducted in compliance with the Commissions regulations, and (3) the issuance of the amendment will not be inimical to the common defense and security or to the health and safety of the public.

5.0 ENVIRONMENTAL CONSIDERATION

A review has determined that the proposed amendment would change a requirement with respect to installation or use of a facility component located within the restricted area, as defined in 10 CFR 20, or would change an inspection or surveillance requirement. However, the proposed amendment does not involve (i) a significant hazards consideration, (ii) a significant change in the types or significant increase in the amounts of any effluents that may be released offsite, or (iii) a significant increase in individual or cumulative occupational radiation exposure. Accordingly, the proposed amendment meets the eligibility criterion for categorical exclusion set forth in 10 CFR 51.22(c)(9). Therefore, pursuant to 10 CFR 51.22(b), no environmental impact statement or environmental assessment need be prepared in connection with the proposed amendment.

CNL-16-001 E18 of 20

ENCLOSURE

6.0 REFERENCES

1. TVA Letter to NRC, CNL-14-218, Application to Modify Watts Bar Nuclear Plant, Unit 1 Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (SQN-TS-13-08), dated April 6, 2015 (ML15117A462)
2. NRC letter to TVA, Watts Bar Nuclear Plant, Unit 1 - Issuance of Amendment Regarding Modification To Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (TAC No. MF6153), dated September 17, 2015 (ML15230A155)
3. Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies"
4. NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998
5. Regulatory Guide 1.9, Revision 1, "Selection, Design, and Qualification of Diesel-Generator Units Used as Onsite Electric Power Systems at Nuclear Power Plants"
6. WCAP-17308-NP, Treatment of Diesel Generator (DG) Technical Specification Frequency and Voltage Tolerances, April 2012
7. G-Spec G-37 R5, Testing and Balancing of HVAC Systems During Installation, Modification, and Maintenance
8. Regulatory Guide 1.6, Revision 0, "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems (Safety Guide 6)"
9. NUREG-1232, Volume 2, Safety Evaluation Report On Tennessee Valley Authority: Sequoyah Nuclear Performance Plan, dated May 1988
10. NRC Letter, "Beaver Valley 1 and 2 - Amendment for Revised Technical Specification Requirements for Emergency Diesel Generators (TAC Nos. MA4438 and MA4439)," dated February 11, 2000 (ML003684928)
11. NRC Letter, "Palo Verde Nuclear Generating Station, Units 1, 2, and 3 - Issuance of Amendments on Diesel Generator Steady-State Voltage and Frequency (TAC Nos. MA9214, MA9215, and MA9216)," dated October 4, 2000 (ML003758500)
12. NRC Letter, Donald C. Cook Nuclear Plant, Units 1 and 2 - Issuance of Amendment to Renewed Facility Operating License Regarding Technical Specification Change Relating to Diesel Generator Steady-State Parameters (TAC Nos. MD8773 and MD8774), dated April 30, 2009 (ML090630245)
13. NRC Letter, "Crystal River Unit 3 Nuclear Generating Plant - Issuance of Amendment Regarding Request to Revise the Technical Specification Surveillance Requirements for Emergency Diesel Generator Voltage and Frequency Limits (TAC No. ME0107), dated December 10, 2009 (ML092680285)

CNL-16-001 E19 of 20

ENCLOSURE

14. NRC Letter, "Wolf Creek Generating Station - Issuance of Amendment Re: Revise Technical Specification 3.8.1, "AC Sources - Operating" (TAC No. ME7674),"

dated April 11, 2013 (ML13077A147)

CNL-16-001 E20 of 20

ATTACHMENT 1 Proposed TS Changes (Mark-Ups) for SQN Units 1 and 2

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.2 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.

Verify each DG starts from standby conditions and In accordance achieves steady state voltage 6800 V and with the 7260 V, and frequency 58.8 Hz and 61.2 Hz. Surveillance Frequency Control Program 59.8 60.2 SR 3.8.1.3 ------------------------------NOTES-----------------------------

1. DG loadings may include gradual loading as recommended by the manufacturer.
2. Momentary transients outside the load range do not invalidate this test.
3. This Surveillance shall be conducted on only one DG at a time.
4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.

Verify each DG is synchronized and loaded and In accordance operates for 60 minutes at a load 3960 kW and with the 4400 kW. Surveillance Frequency Control Program SEQUOYAH - UNIT 1 3.8.1-6 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.4 Verify each engine-mounted day tank contains In accordance 250 gal of fuel oil. with the Surveillance Frequency Control Program SR 3.8.1.5 Check for and remove accumulated water from each In accordance engine-mounted day tank. with the Surveillance Frequency Control Program SR 3.8.1.6 Verify the fuel oil transfer system operates to In accordance transfer fuel oil from the storage system to the with the engine-mounted day tanks. Surveillance Frequency Control Program SR 3.8.1.7 ------------------------------NOTE-------------------------------

All DG starts may be preceded by an engine prelube period.

Verify each DG starts from standby condition and In accordance achieves: with the Surveillance

a. In 10 seconds, voltage 6800 V and Frequency frequency 58.8 Hz and Control Program
b. Steady state voltage 6800 V and 7260 V, and frequency 58.8 Hz and 61.2 Hz.

59.8 60.2 SEQUOYAH - UNIT 1 3.8.1-7 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.8 ------------------------------NOTES-----------------------------

1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.

Verify automatic and manual transfer of the power In accordance supply to each 6.9 kV Unit Board from the normal with the supply to the alternate supply. Surveillance Frequency Control Program SR 3.8.1.9 ------------------------------NOTE------------------------------

If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.

Under this condition the power factor shall be maintained as close to the limit as practicable.

Verify each DG rejects a load greater than or equal In accordance to its associated single largest post-accident load, with the and: Surveillance Frequency

a. Following load rejection, the frequency is Control Program 66.5 Hz,
b. Within 3 seconds following load rejection, the voltage is 6800 V and 7260 V, and
c. Within 3 seconds following load rejection, the frequency is 58.8 Hz and 61.2 Hz.

SEQUOYAH - UNIT 1 59.8 60.2 3.8.1-8 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.11 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal: with the Surveillance

a. De-energization of shutdown boards, Frequency Control Program
b. Load shedding from shutdown boards,
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected shutdown loads through load sequence timers,
3. Maintains steady state voltage 6800 V and 7260 V,
4. Maintains steady state frequency 58.8 Hz and 61.2 Hz, and
5. Supplies permanently connected and auto-connected shutdown loads for 59.8 60.2 5 minutes.

SEQUOYAH - UNIT 1 3.8.1-10 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.12 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated Engineered Safety In accordance Feature (ESF) actuation signal each DG auto-starts with the from standby condition and: Surveillance Frequency

a. In 10 seconds after auto-start and during Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
b. Achieves steady state voltage 6800 V and 7260 V and frequency 58.8 Hz and 61.2 Hz,
c. Operates for 5 minutes, 59.8 60.2 d. Permanently connected loads remain energized from the offsite power system, and
e. Emergency loads are energized from the offsite power system.

SEQUOYAH - UNIT 1 3.8.1-11 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.15 ------------------------------NOTES-----------------------------

1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> loaded 3960 kW and 4400 kW and 2140 kvar and 2370 kvar.

Momentary transients outside of load range do not invalidate this test.

2. All DG starts may be preceded by an engine prelube period.

Verify each DG starts and achieves: In accordance with the

a. In 10 seconds, voltage 6800 V and Surveillance frequency 58.8 Hz and Frequency Control Program
b. Steady state voltage 6800 V, and 7260 V and frequency 58.8 Hz and 61.2 Hz.

SR 3.8.1.16 ------------------------------NOTE-------------------------------

For DGs 59.8 1A-A and 1B-B, 60.2this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify each DG: In accordance with the

a. Synchronizes with offsite power source while Surveillance loaded with emergency loads upon a simulated Frequency restoration of offsite power, Control Program
b. Transfers loads to offsite power source, and
c. Returns to ready-to-load operation.

SEQUOYAH - UNIT 1 3.8.1-13 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.18 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal in conjunction with an actual or simulated with the ESF actuation signal: Surveillance Frequency

a. De-energization of shutdown boards, Control Program
b. Load shedding from shutdown boards, and
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected emergency loads through load sequence timers,
3. Achieves steady state voltage 6800 V and 7260 V,
4. Achieves steady state frequency 58.8 Hz and 61.2 Hz, and
5. Supplies permanently connected and auto-connected emergency 59.8 loads for 60.2 5 minutes.

SEQUOYAH - UNIT 1 3.8.1-15 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.2 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.

Verify each DG starts from standby conditions and In accordance achieves steady state voltage 6800 V and with the 7260 V, and frequency 58.8 Hz and 61.2 Hz. Surveillance Frequency Control Program 59.8 60.2 SR 3.8.1.3 ------------------------------NOTES-----------------------------

1. DG loadings may include gradual loading as recommended by the manufacturer.
2. Momentary transients outside the load range do not invalidate this test.
3. This Surveillance shall be conducted on only one DG at a time.
4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.

Verify each DG is synchronized and loaded and In accordance operates for 60 minutes at a load 3960 kW and with the 4400 kW. Surveillance Frequency Control Program SEQUOYAH - UNIT 2 3.8.1-6 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.4 Verify each engine-mounted day tank contains In accordance 250 gal of fuel oil. with the Surveillance Frequency Control Program SR 3.8.1.5 Check for and remove accumulated water from each In accordance engine-mounted day tank. with the Surveillance Frequency Control Program SR 3.8.1.6 Verify the fuel oil transfer system operates to In accordance transfer fuel oil from the storage system to the with the engine-mounted day tanks. Surveillance Frequency Control Program SR 3.8.1.7 ------------------------------NOTE-------------------------------

All DG starts may be preceded by an engine prelube period.

Verify each DG starts from standby condition and In accordance achieves: with the Surveillance

a. In 10 seconds, voltage 6800 V and Frequency frequency 58.8 Hz and Control Program
b. Steady state voltage 6800 V and 7260 V, and frequency 58.8 Hz and 61.2 Hz.

59.8 60.2 SEQUOYAH - UNIT 2 3.8.1-7 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.8 ------------------------------NOTES-----------------------------

1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.

Verify automatic and manual transfer of the power In accordance supply to each 6.9 kV Unit Board from the normal with the supply to the alternate supply. Surveillance Frequency Control Program SR 3.8.1.9 ------------------------------NOTE-------------------------------

If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.

Under this condition the power factor shall be maintained as close to the limit as practicable.

Verify each DG rejects a load greater than or equal In accordance to its associated single largest post-accident load, with the and: Surveillance Frequency

a. Following load rejection, the frequency is Control Program 66.5 Hz,
b. Within 3 seconds following load rejection, the voltage is 6800 V and 7260 V, and
c. Within 3 seconds following load rejection, the frequency is 58.8 Hz and 61.2 Hz.

59.8 60.2 SEQUOYAH - UNIT 2 3.8.1-8 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.11 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal: with the Surveillance

a. De-energization of shutdown boards, Frequency Control Program
b. Load shedding from shutdown boards,
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected shutdown loads through load sequence timers,
3. Maintains steady state voltage 6800 V and 7260 V,
4. Maintains steady state frequency 58.8 Hz and 61.2 Hz, and
5. Supplies permanently connected and auto-connected shutdown loads for 59.8 60.2 5 minutes.

SEQUOYAH - UNIT 2 3.8.1-10 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.12 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated Engineered Safety In accordance Feature (ESF) actuation signal each DG auto-starts with the from standby condition and: Surveillance Frequency

a. In 10 seconds after auto-start and during Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
b. Achieves steady state voltage 6800 V and 7260 V and frequency 58.8 Hz and 61.2 Hz,
c. Operates for 5 minutes, 59.8
d. Permanently connected loads remain energized 60.2 from the offsite power system, and
e. Emergency loads are energized from the offsite power system.

SEQUOYAH - UNIT 2 3.8.1-11 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.15 ------------------------------NOTES-----------------------------

1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> loaded 3960 kW and 4400 kW and 2140 kvar and 2370 kvar.

Momentary transients outside of load range do not invalidate this test.

2. All DG starts may be preceded by an engine prelube period.

Verify each DG starts and achieves: In accordance with the

a. In 10 seconds, voltage 6800 V and Surveillance frequency 58.8 Hz and Frequency Control Program
b. Steady state voltage 6800 V, and 7260 V and frequency 58.8 Hz and 61.2 Hz.

SR 3.8.1.16 ------------------------------NOTE-------------------------------

For DGs 59.82A-A and 2B-B, this Surveillance shall 60.2not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify each DG: In accordance with the

a. Synchronizes with offsite power source while Surveillance loaded with emergency loads upon a simulated Frequency restoration of offsite power, Control Program
b. Transfers loads to offsite power source, and
c. Returns to ready-to-load operation.

SEQUOYAH - UNIT 2 3.8.1-13 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.18 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal in conjunction with an actual or simulated with the ESF actuation signal: Surveillance Frequency

a. De-energization of shutdown boards, Control Program
b. Load shedding from shutdown boards, and
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected emergency loads through load sequence timers,
3. Achieves steady state voltage 6800 V and 7260 V,
4. Achieves steady state frequency 58.8 Hz and 61.2 Hz, and
5. Supplies permanently connected and auto-connected emergency loads 59.8 for 5 minutes. 60.2 SEQUOYAH - UNIT 2 3.8.1-15 Amendment 327

ATTACHMENT 2 Proposed TS Bases Changes (Mark-Ups) for SQN Units 1 and 2 (For Information Only)

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).

Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).

Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.

The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.

The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/- 2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).

SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3).

These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.

SEQUOYAH - UNIT 1 B 3.8.1-16 Revision 45

AC Sources - Operating B 3.8.1 During this testing, the diesel is BASES not in an accident mode and the frequency is controlled by SURVEILLANCE REQUIREMENTS (continued) the operator instead of the governors accident speed SR 3.8.1.2 and SR 3.8.1.7 reference.

These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.

To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.

For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.

In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.

SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).

The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.

Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.

In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 1 B 3.8.1-17 Revision 45

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:

a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
b. Tripping its associated single largest post-accident load with the DG solely supplying the board. and Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejectionmaximum test is transient acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.

The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.

SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.

These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to 0.89 results in voltages on the emergency boards that are too high.

SEQUOYAH - UNIT 1 B 3.8.1-21 Revision 45

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).

Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).

Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.

The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.

The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/- 2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).

SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program. The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3).

These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.

SEQUOYAH - UNIT 2 B 3.8.1-16 Revision 44

AC Sources - Operating B 3.8.1 During this testing, the diesel is not in an accident mode and BASES the frequency is controlled by the operator instead of the SURVEILLANCE REQUIREMENTS (continued) governors accident speed reference.

SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.

To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.

For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.

In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.

SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).

The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.

Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.

In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 2 B 3.8.1-17 Revision 45

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:

a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
b. Tripping its associated single largest post-accident load with the DG solely supplying the board. and Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejectionmaximum test is transient acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.

The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.

SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.

These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to 0.89 results in voltages on the emergency boards that are too high.

SEQUOYAH - UNIT 2 B 3.8.1-21 Revision 45

ATTACHMENT 3 Proposed TS Changes (Final Typed) for SQN Units 1 and 2

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.2 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.

Verify each DG starts from standby conditions and In accordance achieves steady state voltage 6800 V and with the 7260 V, and frequency 59.8 Hz and 60.2 Hz. Surveillance Frequency Control Program SR 3.8.1.3 ------------------------------NOTES-----------------------------

1. DG loadings may include gradual loading as recommended by the manufacturer.
2. Momentary transients outside the load range do not invalidate this test.
3. This Surveillance shall be conducted on only one DG at a time.
4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.

Verify each DG is synchronized and loaded and In accordance operates for 60 minutes at a load 3960 kW and with the 4400 kW. Surveillance Frequency Control Program SEQUOYAH - UNIT 1 3.8.1-6 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.4 Verify each engine-mounted day tank contains In accordance 250 gal of fuel oil. with the Surveillance Frequency Control Program SR 3.8.1.5 Check for and remove accumulated water from each In accordance engine-mounted day tank. with the Surveillance Frequency Control Program SR 3.8.1.6 Verify the fuel oil transfer system operates to In accordance transfer fuel oil from the storage system to the with the engine-mounted day tanks. Surveillance Frequency Control Program SR 3.8.1.7 ------------------------------NOTE-------------------------------

All DG starts may be preceded by an engine prelube period.

Verify each DG starts from standby condition and In accordance achieves: with the Surveillance

a. In 10 seconds, voltage 6800 V and Frequency frequency 58.8 Hz and Control Program
b. Steady state voltage 6800 V and 7260 V, and frequency 59.8 Hz and 60.2 Hz.

SEQUOYAH - UNIT 1 3.8.1-7 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.8 ------------------------------NOTES-----------------------------

1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.

Verify automatic and manual transfer of the power In accordance supply to each 6.9 kV Unit Board from the normal with the supply to the alternate supply. Surveillance Frequency Control Program SR 3.8.1.9 ------------------------------NOTE------------------------------

If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.

Under this condition the power factor shall be maintained as close to the limit as practicable.

Verify each DG rejects a load greater than or equal In accordance to its associated single largest post-accident load, with the and: Surveillance Frequency

a. Following load rejection, the frequency is Control Program 66.5 Hz,
b. Within 3 seconds following load rejection, the voltage is 6800 V and 7260 V, and
c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and 60.2 Hz.

SEQUOYAH - UNIT 1 3.8.1-8 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.11 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal: with the Surveillance

a. De-energization of shutdown boards, Frequency Control Program
b. Load shedding from shutdown boards,
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected shutdown loads through load sequence timers,
3. Maintains steady state voltage 6800 V and 7260 V,
4. Maintains steady state frequency 59.8 Hz and 60.2 Hz, and
5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.

SEQUOYAH - UNIT 1 3.8.1-10 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.12 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated Engineered Safety In accordance Feature (ESF) actuation signal each DG auto-starts with the from standby condition and: Surveillance Frequency

a. In 10 seconds after auto-start and during Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
b. Achieves steady state voltage 6800 V and 7260 V and frequency 59.8 Hz and 60.2 Hz,
c. Operates for 5 minutes,
d. Permanently connected loads remain energized from the offsite power system, and
e. Emergency loads are energized from the offsite power system.

SEQUOYAH - UNIT 1 3.8.1-11 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.15 ------------------------------NOTES-----------------------------

1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> loaded 3960 kW and 4400 kW and 2140 kvar and 2370 kvar.

Momentary transients outside of load range do not invalidate this test.

2. All DG starts may be preceded by an engine prelube period.

Verify each DG starts and achieves: In accordance with the

a. In 10 seconds, voltage 6800 V and Surveillance frequency 58.8 Hz and Frequency Control Program
b. Steady state voltage 6800 V, and 7260 V and frequency 59.8 Hz and 60.2 Hz.

SR 3.8.1.16 ------------------------------NOTE-------------------------------

For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify each DG: In accordance with the

a. Synchronizes with offsite power source while Surveillance loaded with emergency loads upon a simulated Frequency restoration of offsite power, Control Program
b. Transfers loads to offsite power source, and
c. Returns to ready-to-load operation.

SEQUOYAH - UNIT 1 3.8.1-13 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.18 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal in conjunction with an actual or simulated with the ESF actuation signal: Surveillance Frequency

a. De-energization of shutdown boards, Control Program
b. Load shedding from shutdown boards, and
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected emergency loads through load sequence timers,
3. Achieves steady state voltage 6800 V and 7260 V,
4. Achieves steady state frequency 59.8 Hz and 60.2 Hz, and
5. Supplies permanently connected and auto-connected emergency loads for 5 minutes.

SEQUOYAH - UNIT 1 3.8.1-15 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.2 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.

Verify each DG starts from standby conditions and In accordance achieves steady state voltage 6800 V and with the 7260 V, and frequency 59.8 Hz and 60.2 Hz. Surveillance Frequency Control Program SR 3.8.1.3 ------------------------------NOTES-----------------------------

1. DG loadings may include gradual loading as recommended by the manufacturer.
2. Momentary transients outside the load range do not invalidate this test.
3. This Surveillance shall be conducted on only one DG at a time.
4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.

Verify each DG is synchronized and loaded and In accordance operates for 60 minutes at a load 3960 kW and with the 4400 kW. Surveillance Frequency Control Program SEQUOYAH - UNIT 2 3.8.1-6 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.4 Verify each engine-mounted day tank contains In accordance 250 gal of fuel oil. with the Surveillance Frequency Control Program SR 3.8.1.5 Check for and remove accumulated water from each In accordance engine-mounted day tank. with the Surveillance Frequency Control Program SR 3.8.1.6 Verify the fuel oil transfer system operates to In accordance transfer fuel oil from the storage system to the with the engine-mounted day tanks. Surveillance Frequency Control Program SR 3.8.1.7 ------------------------------NOTE-------------------------------

All DG starts may be preceded by an engine prelube period.

Verify each DG starts from standby condition and In accordance achieves: with the Surveillance

a. In 10 seconds, voltage 6800 V and Frequency frequency 58.8 Hz and Control Program
b. Steady state voltage 6800 V and 7260 V, and frequency 59.8 Hz and 60.2 Hz.

SEQUOYAH - UNIT 2 3.8.1-7 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.8 ------------------------------NOTES-----------------------------

1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.

Verify automatic and manual transfer of the power In accordance supply to each 6.9 kV Unit Board from the normal with the supply to the alternate supply. Surveillance Frequency Control Program SR 3.8.1.9 ------------------------------NOTE-------------------------------

If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.

Under this condition the power factor shall be maintained as close to the limit as practicable.

Verify each DG rejects a load greater than or equal In accordance to its associated single largest post-accident load, with the and: Surveillance Frequency

a. Following load rejection, the frequency is Control Program 66.5 Hz,
b. Within 3 seconds following load rejection, the voltage is 6800 V and 7260 V, and
c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and 60.2 Hz.

SEQUOYAH - UNIT 2 3.8.1-8 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.11 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal: with the Surveillance

a. De-energization of shutdown boards, Frequency Control Program
b. Load shedding from shutdown boards,
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected shutdown loads through load sequence timers,
3. Maintains steady state voltage 6800 V and 7260 V,
4. Maintains steady state frequency 59.8 Hz and 60.2 Hz, and
5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.

SEQUOYAH - UNIT 2 3.8.1-10 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.12 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated Engineered Safety In accordance Feature (ESF) actuation signal each DG auto-starts with the from standby condition and: Surveillance Frequency

a. In 10 seconds after auto-start and during Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
b. Achieves steady state voltage 6800 V and 7260 V and frequency 59.8 Hz and 60.2 Hz,
c. Operates for 5 minutes,
d. Permanently connected loads remain energized from the offsite power system, and
e. Emergency loads are energized from the offsite power system.

SEQUOYAH - UNIT 2 3.8.1-11 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.15 ------------------------------NOTES-----------------------------

1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> loaded 3960 kW and 4400 kW and 2140 kvar and 2370 kvar.

Momentary transients outside of load range do not invalidate this test.

2. All DG starts may be preceded by an engine prelube period.

Verify each DG starts and achieves: In accordance with the

a. In 10 seconds, voltage 6800 V and Surveillance frequency 58.8 Hz and Frequency Control Program
b. Steady state voltage 6800 V, and 7260 V and frequency 59.8 Hz and 60.2 Hz.

SR 3.8.1.16 ------------------------------NOTE-------------------------------

For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify each DG: In accordance with the

a. Synchronizes with offsite power source while Surveillance loaded with emergency loads upon a simulated Frequency restoration of offsite power, Control Program
b. Transfers loads to offsite power source, and
c. Returns to ready-to-load operation.

SEQUOYAH - UNIT 2 3.8.1-13 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.18 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal in conjunction with an actual or simulated with the ESF actuation signal: Surveillance Frequency

a. De-energization of shutdown boards, Control Program
b. Load shedding from shutdown boards, and
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected emergency loads through load sequence timers,
3. Achieves steady state voltage 6800 V and 7260 V,
4. Achieves steady state frequency 59.8 Hz and 60.2 Hz, and
5. Supplies permanently connected and auto-connected emergency loads for 5 minutes.

SEQUOYAH - UNIT 2 3.8.1-15 Amendment 32X

ATTACHMENT 4 Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).

Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).

Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.

The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.

The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.

SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 1 B 3.8.1-16 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.

To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.

For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.

In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.

SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).

The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used.

During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governors accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.

Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.

In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 1 B 3.8.1-17 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:

a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
b. Tripping its associated single largest post-accident load with the DG solely supplying the board.

Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.

The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.

SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.

These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to 0.89 results in voltages on the emergency boards that are too high.

SEQUOYAH - UNIT 1 B 3.8.1-21 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).

Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).

Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.

The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.

The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.

SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 2 B 3.8.1-16 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.

To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.

For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.

In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.

SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).

The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used.

During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governors accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.

Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.

In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 2 B 3.8.1-17 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:

a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
b. Tripping its associated single largest post-accident load with the DG solely supplying the board.

Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.

The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.

SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.

These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to 0.89 results in voltages on the emergency boards that are too high.

SEQUOYAH - UNIT 2 B 3.8.1-21 Revision XX

Tennessee Valley Authority, 1101 Market Street, Chattanooga, Tennessee 37402 CNL-16-001 May 26, 2016 10 CFR 50.90 U.S. Nuclear Regulatory Commission ATTN: Document Control Desk Washington, D.C. 20555-0001 Sequoyah Nuclear Plant Units 1 and 2 Renewed Facility Operating License Nos. DPR-77 and DPR-79 NRC Docket Nos. 50-327 and 50-328

Subject:

Application to Modify Sequoyah Nuclear Plant, Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02)

In accordance with the provisions of Title 10 of the Code of Federal Regulations (10 CFR) 50.90, "Application for amendment of license, construction permit, or early site permit,"

Tennessee Valley Authority (TVA) is submitting a request for an amendment (SQN-TS-14-02) to Renewed Facility Operating License Nos. DPR-77 and DPR-79 for the Sequoyah Nuclear Plant (SQN) Units 1 and 2.

This license amendment request proposes to amend the SQN Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. Currently, the acceptance criteria are 58.8 Hz and 61.2 Hz. TVA proposes to change the SQN DG steady state frequency acceptance criteria to 59.8 Hz and 60.2 Hz. The DG TS SR steady state voltage range of 6800 V and 7260 V is unaffected.

TVA has determined that the steady state frequency range acceptance criteria currently specified by SQN TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are non-conservative. A Condition Report (CR) was initiated in accordance with the TVA Corrective Action Program. Subsequently, a prompt determination of operability (PDO),

including administrative controls were established in accordance with the Nuclear Regulatory Commission (NRC) Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998. As a result of the CR, a number of immediate/interim and other corrective actions were identified, implemented, and completed. A review of historical DG test records for frequency and voltage supported the fact that the DGs were operable and supported the existing design basis analyses accidents. Administrative controls for DG frequency have been implemented in the applicable Surveillance Instructions to support continued DG operability.

U.S. Nuclear Regulatory Commission CNL-16-001 Page 2 May 26, 2016 The enclosure to this letter provides a description of the proposed changes, technical evaluation of the proposed changes, regulatory evaluation, and a discussion of environmental considerations. Attachments 1 and 2 to the enclosure provide the existing TS and Bases pages marked-up to show the proposed changes. Attachments 3 and 4 to the enclosure provide the existing TS and Bases pages retyped to show the proposed changes. Changes to the existing TS Bases, are provided for information only and will be implemented under the Technical Specification Bases Control Program.

As noted in the enclosure, the modified SR 3.8.1.9 is normally performed during outages.

Therefore, TVA requests NRC approval of this proposed license amendment by May 2017 with implementation during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy the revised SR 3.8.1.9 prior to implementation of this proposed license amendment.

TVA has determined that there are no significant hazard considerations associated with the proposed change and that the change qualifies for a categorical exclusion from environmental review pursuant to the provisions of 10 CFR 51 .22(c)(9).

The SQN Plant Operations Review Committee and the TVA Nuclear Safety Review Board have reviewed this proposed change and determined that operation of SQN Units 1 and 2 in accordance with the proposed change will not endanger the health and safety of the public.

In accordance with 10 CFR 50.91(b)(1), TVA is sending a copy of this letter and the enclosure to the Tennessee Department of Environment and Conservation.

There are no new regulatory commitments associated with this submittal. Please address any questions regarding this request to Ed Schrull at (423) 751-3850.

I declare under penalty of perjury that the foregoing is true and correct. Executed on this 26th day of May 2016.

President, Nuclear Licensing Enclosure cc: See Page 3

U.S. Nuclear Regulatory Commission CNL-16-001 Page 3 May 26, 2016 RDW: EDS

Enclosure:

Evaluation of Proposed Change cc (Enclosure):

NRC Regional Administrator - Region II NRC Senior Resident Inspector - Sequoyah Nuclear Plant NRR Project Manager - Sequoyah Nuclear Plant Director, Division of Radiological Health - Tennessee State Department of Environment and Conservation

ENCLOSURE TENNESSEE VALLEY AUTHORITY SEQUOYAH NUCLEAR PLANT UNITS 1 AND 2 EVALUATION OF PROPOSED CHANGE

Subject:

Application to Modify Sequoyah Nuclear Plant Units 1 and 2 Technical Specifications Regarding Diesel Generator Steady State Frequency (SQN-TS-14-02) 1.0

SUMMARY

DESCRIPTION 2.0 DETAILED DESCRIPTION 2.1 Proposed Change 2.2 Need for Proposed Changes 2.3 Implementation

3.0 TECHNICAL EVALUATION

3.1 System Description 3.2 Evaluation 3.3 Conclusion

4.0 REGULATORY EVALUATION

4.1 Applicable Regulatory Requirements and Criteria 4.2 Precedent 4.3 Significant Hazards Consideration 4.4 Conclusion

5.0 ENVIRONMENTAL CONSIDERATION

6.0 REFERENCES

ATTACHMENTS

1. Proposed TS Changes (Mark-Ups) for SQN Units 1 and 2
2. Proposed TS Bases Changes (Mark-Ups) for SQN Units 1 and 2 (For Information Only)
3. Proposed TS Changes (Final Typed) for SQN Units 1 and 2
4. Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)

CNL-16-001 E1 of 20

ENCLOSURE 1.0

SUMMARY

DESCRIPTION The Tennessee Valley Authority (TVA) is requesting a license amendment to amend the Sequoyah Nuclear Plant (SQN) Units 1 and 2 Technical Specifications (TS) by modifying the acceptance criteria for the diesel generator (DG) steady state frequency range provided in SQN Units 1 and 2, TS 3.8.1, "AC Sources - Operating. Specifically, the proposed change and supporting evaluation will modify the acceptance criteria for the DG steady state frequency range provided in SQN Units 1 and 2 TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18.

Currently, the DG SR steady state acceptance criteria are 58.8 Hz and 61.2 Hz.

TVA proposes to change the SQN DG steady state frequency acceptance criteria to 59.8 Hz and 60.2 Hz. The DG TS SR steady state voltage range of 6800 V and 7260 V is not affected. This license amendment request (LAR) is similar to a Watts Bar Nuclear Plant (WBN) Unit 1 submittal (Reference 1), which was approved by the NRC in Reference 2.

This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed.

However, no specific changes to SR 3.8.1.3 or TS 3.8.2 are required.

2.0 DETAILED DESCRIPTION 2.1 Proposed Changes Currently, the acceptance criteria for DG steady state frequency specified in SQN Units 1 and 2, TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 are 58.8 Hz and 61.2 Hz. TVA proposes to conservatively narrow the DG frequency range by increasing the current DG frequency lower limit of 58.8 Hz to 59.8 Hz and decreasing the current upper limit from the existing 61.2 Hz to 60.2 Hz in the SQN Units 1 and 2 TS1 (i.e., SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18) and TS Bases 3.8.1. The proposed SQN Units 1 and 2 DG frequency and voltage steady state operating ranges only apply to the steady state condition of DG operation, and are summarized below in Table 1.

Table 1 Technical Specification DG Steady-State Operating Range Parameter Range Frequency 59.8 Hz to 60.2 Hz Voltage 6800 V to 7260 V This change is applicable to the surveillances performed at 31 days, 18 months, and ten years when maintenance & test equipment (M&TE) is installed on the DG per the surveillance instructions.

1 Note: No change is required to SQN Units 1 and 2, TS SR 3.8.1.19 because that surveillance does not apply to steady state operation.

CNL-16-001 E2 of 20

ENCLOSURE The DG voltage limits as described in the Technical Specifications are correct and do not require revision.

Attachments 1 and 2 to this enclosure provide the existing SQN Units 1 and 2 TS and Bases pages marked-up to show the proposed changes. Attachments 3 and 4 to this enclosure provide the clean typed TS and Bases pages with the proposed changes incorporated.

The proposed Bases changes are provided to the NRC for information only.

2.2 Need for Proposed Changes Plant safety analyses make specific assumptions regarding the emergency core cooling system (ECCS) flow to provide the core cooling function following any event that requires safety injection (SI) to mitigate the event. For the events that assume a loss of offsite power (LOOP), the DGs provide power to the ECCS pumps. Following a LOOP, each DG starts and ties to an engineered safety feature (ESF) board, and essential loads, including the ECCS pumps, are sequentially connected to the ESF board by individual timers for each load sequence. The calculated ECCS flow rates assume that the steady state DG frequency is 60 Hz (i.e., after the DG starting and loading transients).

Once the DG starting and loading sequences are complete, the DG governor maintains the frequency at 60 Hz within a specified tolerance, which is based on the governor manufacturer/model.

The ECCS flow provided by the ECCS pumps is affected by the pump speed, which in turn is a function of the DG frequency. Historically, the DG frequency tolerances associated with the governor were not considered in the development of the ECCS, containment spray system (CSS), and auxiliary feedwater (AFW) flow rates. The primary effect of changes in DG frequency on the ECCS safety functions is an increase or decrease in the speed of safety-related motors that are powered by the DG. The increase or decrease in the speed of the motors affects pump performance, motor operated valve (MOV) stroke times, cooling fan performance, and DG loading, among other factors.

The minimum and maximum frequency values of 58.8 Hz and 61.2 Hz in the SQN TS SRs are equal to +/- 2% of the 60 Hz nominal frequency (i.e., the TS specified plant specific transient range). However, the +/- 2% frequency tolerance is only applicable to DG starting and loading transients, and does not apply to steady state operation as discussed in Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies" (Reference 3).

Because the safety analyses did not consider the effects of operating at the extremes of the steady state frequency range specified in TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18, TVA has determined that the current SQN Units 1 and 2 TS SR acceptance criteria for steady state DG frequency are non-conservative. The non-conservative acceptance criteria were addressed within the TVA corrective action program (CAP) and administrative controls were established in accordance with NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety" (Reference 4). To address the non-conservative TS, CNL-16-001 E3 of 20

ENCLOSURE TVA is proposing a change to TS SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18 to revise the DG SR steady state acceptance criteria to 59.8 Hz and 60.2 Hz.

The four SQN DGs are shared between SQN Units 1 and 2, as described in Section 3.1, and the SRs for all four DGs are specified in the SQN Units 1 and 2 TSs. Therefore, the proposed SR steady state frequency acceptance criteria of 59.8 Hz and 60.2 Hz would apply to all four DGs.

2.3 Implementation The TVA process governing the preparation and submittal of TS changes and LARs requires that the appropriate organizations (e.g., Operations, Training, Engineering, Maintenance, Chemistry, Radiation Protection, and Work Control) identify the documents that are affected by each proposed change to the TSs and Operating Licenses. Among the items that are considered are training, plant modifications, procedures, special implementation constraints, design documents, and surveillance instructions associated with TS SRs, Technical Requirements Manual, TS Bases, and the Updated Final Safety Analysis Report (UFSAR). The process requires that procedures and design document changes necessary to support TS Operability are approved prior to implementation of an NRC approved license amendment. The process also provides assurance that the remaining changes, if any, are scheduled and tracked for configuration control.

SR 3.8.1.9 requires verification that each DG can maintain acceptable frequency following a load rejection greater than or equal to the single largest post-accident load.

This SR includes verification that the DG can restore frequency within the allowable steady-state band within three seconds. SQN currently performs SR 3.8.1.9 concurrent with SR 3.8.1.10, which verifies that the DG can withstand a full load rejection (from a fully loaded condition). This approach is acceptable because the full load rejection of SR 3.8.1.10 as well as the single largest post-accident load requirement of SR 3.8.1.9 are performed. The current test methodology for both SR 3.8.1.9 and 3.8.1.10 requires the DG to initially be in parallel with offsite power to achieve the required power value.

When the DG is operating in parallel with offsite power for surveillance testing, the speed droop circuit in the DG speed governor is required to be in service (i.e., non-emergency /

droop test mode). The speed droop function is necessary to ensure stable and controllable load-sharing between the DG and offsite power. However, the speed droop results in a steady-state frequency greater than the nominal 60 Hz value following a load rejection. Historical data shows that DG frequency typically stabilizes at approximately 60.3 Hz following a single largest load rejection with speed droop in service. This final frequency value is acceptable under the current SR 3.8.1.9, but is outside the more stringent frequency criteria proposed in this LAR. These results are due to the surveillance test methodology (i.e., performing the load rejection with the speed droop circuit in service) rather than being an indication of a problem or malfunction in the DG speed governor.

CNL-16-001 E4 of 20

ENCLOSURE To successfully perform SR 3.8.1.9 with the more conservative frequency band proposed in this LAR, the test methodology must be modified to perform the load rejection with the DG in accident mode (emergency / isochronous mode) and isolated on the shutdown board (i.e., not initially in parallel with offsite power). In the accident mode, the DG speed governor uses a fixed speed reference corresponding to 60.0 Hz, which ensures that the frequency criteria of SR 3.8.1.9 can be met. This requires a revision to the surveillance test procedures to perform SR 3.8.1.9 in conjunction with SR 3.8.1.18 (shutdown board blackout testing). This change in methodology is beneficial because it more closely replicates the conditions under which the DGs may have to perform following a loss of offsite power. TVA has initiated action to ensure that the applicable surveillance testing procedures are revised to incorporate this change prior to the next unit refueling outage on each SQN unit. Because the modified SR 3.8.1.9 is normally performed during outages, TVA is requesting implementation of this proposed license amendment during or after the next refueling outage on SQN Unit 2 (scheduled to be completed in May 2017). This will allow all four DGs to be tested via the new test methodology to satisfy revised SR 3.8.1.9 prior to implementation of this proposed license amendment.

3.0 TECHNICAL EVALUATION

3.1 System Description The onsite Class 1E alternating current (AC) standby system is described in SQN UFSAR Section 8.3, "Onsite Power System.

As noted in SQN UFSAR Section 8.3, the onsite AC power system is a Class 1E system, which consists of the standby AC power system and the 120 V vital AC system. The standby AC power system is a safety-related system, which supplies power for energizing all AC-powered electrical devices essential to safety. The safety function of the standby AC power system is to supply power to permit functioning of components and systems required to assure that: (1) fuel design limits and reactor coolant pressure boundary design conditions are not exceeded due to anticipated operational occurrences, and (2) the core is cooled and vital functions are maintained in the event of a postulated accident, subject to loss of the preferred power system and subject to any single failure in the standby power system.

Specifically, the standby AC power system includes:

  • four 6.9 kV shutdown boards and logic relay panels
  • associated 6.9 kV/480 V transformers and 480 V shutdown boards
  • motor control centers supplied by the 480 V shutdown boards The AC standby power system is divided into two redundant load groups (power trains).

The 6.9 kV shutdown boards are arranged electrically into two power trains with two boards associated with each train and each unit. The boards comprising train A are located in the SQN Unit 1 side and those of train B are located in the SQN Unit 2 side.

The train A boards are separated from the train B boards by a reinforced concrete block wall, which is a qualified fire barrier, extended to the ceiling. When the preferred (offsite) power system is not available, each shutdown board is energized from a separate standby DG.

CNL-16-001 E5 of 20

ENCLOSURE A loss of voltage on the 6.9 kV shutdown board starts the associated DG and initiates logic that trips the supply feeder breakers, all 6.9 kV loads (except the 480 V shutdown board transformers), and the major 480 V loads. The bypass breaker for the 480 V shutdown boards current-limiting inductive reactor is also closed as part of this logic.

When the DG has reached rated speed and voltage, the generator is automatically connected to the 6.9 kV shutdown board. This return of voltage to the 6.9 kV shutdown board initiates logic that connects the required loads in sequence. The standby (onsite) power system's automatic sequencing logic is designed to automatically connect the required loads in proper sequence should the logic receive an accident signal prior to, concurrent with, or following a loss of all nuclear unit and preferred (offsite) power.

As noted in UFSAR Section 8.3.1.1, there are two loading sequences:

One, which is applied in the absence of a safety injection signal (SIS), the non-accident condition, and the other accident condition, applied when an SIS (and containment spray actuation signal) is received coincident with a sustained loss of voltage on the 6.9 kV shutdown board.

A loss of offsite power coincident with an SIS is the design basis event; however, as noted in UFSAR Section 8.3.1.1, an SIS received during the course of a non-accident shutdown loading sequence would cause the actions described below.

1. Loads already sequentially connected that are not required for an accident will be disconnected (except fire pumps powered by the DG).
2. Loads already sequentially connected that are required for an accident will remain connected.
3. Loads pending sequential loading that are not required for an accident will not be connected.
4. Loads awaiting sequential loading that are required for an accident will have their sequential timers reset to time zero from which they will then be sequentially loaded.

An SIS received in the absence of a sustained loss of voltage on a 6.9 kV shutdown board would start the DGs, but would not connect them to the shutdown boards.

Each DG consists of two 16-cylinder engines directly connected to a 6.9 kV generator.

The continuous rating of each DG is 4400 kilowatt (kW) at 0.8 power factor, 6.9 kV, 3-phase, and 60 Hz. Each DG also has an additional rating of 4840 kW for 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> out of 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />.

Ratings for the DGs satisfy the requirements of Regulatory Guide 1.9 as clarified in Section 4.1. The continuous service rating of each DG is 4400 kW with 10% overload permissible for up to 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> in any 24 hour2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> period.

The normal operating speed of the DGs is 900 rpm. The DGs use a tandem arrangement; that is, each DG consists of two diesel engines with a generator between them connected together to form a common shaft. The DGs are physically separated, electrically isolated from each other, and protected from the probable maximum flood.

CNL-16-001 E6 of 20

ENCLOSURE The DGs are equipped with Woodward governors and consist of:

  • an EGB-13P actuator on each engine
  • a 2301A computer (reverse biased)
  • a magnetic speed pickup The Woodward EGB-13P actuator used with the 2301A computer is a proportional governor that moves the fuel rack in inverse proportion to the voltage signal from the computer. There is a governor actuator on each DG engine and they are electrically connected in series so that the loss of signal to one actuator would also result in the loss of signal to the other actuator. Based upon the input from the magnetic speed pickup, the electronic governor sends electric signals to the actuators on the two DG engines.

This signal goes to the coils of each actuator that are connected in series so that each coil receives the same electric signal. The terminal shaft of each actuator will move the same amount for each change in signal, thus the fuel control shaft movement on each DG engine will be identical.

The steady state speed control will be within 0.25 percent of rated speed. The governor design includes circuits to provide high- and low-limit adjustments. These limits set the maximum and minimum speed that can be set by varying the speed-setting milliamp or voltage reference. The low limit can be set as high as rated speed, if desired, eliminating the ability of the process or controller speed setting to reduce speed. The SQN Units 1 and 2 DG electrical governor is set within a speed band that is equivalent to a DG frequency of 59.95 Hz +/- 0.05 Hz.

The SQN Units 1 and 2 DG voltage and frequency regulators were evaluated to ensure they were capable of meeting the TS and associated SRs. The measured values for both voltage and frequency have not exhibited drift and have been consistently within the respective setting band.

The SQN Units 1 and 2 DG voltage regulators and speed regulators are independent devices that are not expected to exhibit drift. This has been demonstrated by the past history of diesel surveillances in which the diesel is operated in isochronous mode. If the two variables drift in different directions (e.g., frequency lower and voltage higher), the combined effect on pump speed would be less than an individual drift.

Based on this independence and stability, the composite impact of frequency and voltage were evaluated independently for the Technical Specification band. The frequency range was analyzed over the full range (i.e., 59.8 Hz to 60.2 Hz) within the voltage setting range (i.e., 6925 V to 7000 V). Likewise, the voltage (i.e., 6800 V to 7260 V) was analyzed over the full range within the frequency range of 59.8 Hz to 60.2 Hz.

Test equipment verifies that the governor controls the DG frequency within the steady-state operational band of 59.8 Hz to 60.2 Hz.

The DGs, as clarified in Section 4.1, satisfy the requirements of Regulatory Guide (RG) 1.9, Revision 0 (Reference 3) and RG 1.9, Revision 1 (Reference 5).

CNL-16-001 E7 of 20

ENCLOSURE 3.2 Evaluation 3.2.1 Introduction Calculations were conducted to determine the effects of the DG frequency variation between 59.8 Hz and 60.2 Hz on plant equipment fed by the DGs following a loss of offsite power (LOOP) or a loss of coolant accident (LOCA) coincident with a LOOP.

The changes in the DG frequency have the direct effect of changing motor speeds for the motors fed from the generators following a LOOP or a LOOP/LOCA. The changes in motor speeds are addressed in Section 3.2.2 and affect the following components:

  • Pumps and Fans (Section 3.2.3)
  • Air compressors and chillers (Section 3.2.4)
  • Motor operated valves (MOVs) (Section 3.2.5)
  • Electrical Equipment (Section 3.2.6)

The changes in these parameters were evaluated to demonstrate that the subject equipment would continue to meet their safety related functions within the analyzed bounds documented in design documents. In addition, the increased horsepower associated with increased frequency was evaluated to ensure that the horsepower increases do not result in exceeding the sustained load ratings for the DGs and the decreased flowrate associated with the revised frequency range was evaluated to ensure pump parameters are adequate. Battery chargers and power transformers do not have motors, but frequency changes were examined to determine if the chargers and transformers would provide acceptable output parameters to continue to meet the specifications and requirements of the downstream components.

The results of these calculations are provided below.

3.2.2 Comparison of Voltage and Frequency Impact Motor speed change, as a function of torque (Reference 6), is:

S = (/N1)(SsynS) where, S = speed change Ssyn = motor synch speed S = motor speed

= original torque N = the new torque The motor speed is directly affected by the frequency. The affected components, listed in Section 3.2.1, are either designed for 6600 V operation with the supply boards rated at 6900 V, or designed for 460 V operation with the supply boards rated CNL-16-001 E8 of 20

ENCLOSURE at 480 V. Therefore, during normal operation, the motors see a voltage higher than their nominal rating. Thus, for the lower voltage limit of 6800 V (473 V on the low voltage side), the motors still have their minimum voltage and produce their design torque. Therefore, a low voltage condition is a non-bounding condition and was not further evaluated. For the high voltage case, the motors could have a voltage of 7260 V (505 V on the low voltage side) or 10 percent above the motor design nominal rating, neglecting any voltage drop from the DG to the motor.

Because the torque developed by a motor is directly proportional to the square of the terminal voltage, the above equation is rewritten in terms of voltage, as follows:

S = [(V/VN)21]*(SsynS) where, S = speed change (SsynS) = motor slip, < 2 percent (the value of 2 percent is based on a review of vendor manuals which demonstrates that the motors have < 2 percent slip)

V = Nominal voltage, 6600 V VN = New voltage, 7260 V S = [(6600/7260)21]*(2 percent)

S = -0.35 percent Thus, with a motor slip of less than 2 percent, the motor speed impact is less than 0.35 percent due to the voltage increase to 7260 V from design voltage of 6600 V.

The frequency shift could result in a + 0.35 percent motor speed and the voltage could result in +0.35 percent motor speed change. Therefore, a speed impact of

+ 0.35 percent was used as the DG frequency impact for analyzing the effect caused either by frequency or voltage variation on the affected components in the following sections.

3.2.3 Effect on Pumps 3.2.3.1 Pump Net Positive Suction Head (NPSH)

The change in the DG frequency was evaluated for the effect on the NPSH available to the following emergency core cooling system (ECCS) pumps. These pumps are fed from the DGs; therefore, they could be affected by the variation in frequency of 59.8 Hz to 60.2 Hz:

  • Safety injection (SI)
  • Centrifugal charging (CC)

An evaluation was performed to determine if the NPSH available (NPSHA) exceeds the NPSH required (NPSHR) for the RHR and the CS pumps while taking suction from the containment sump (recirculation mode). The evaluation also determined CNL-16-001 E9 of 20

ENCLOSURE the NPSH Margin for the CS, SI, RHR, and CC pumps during injection mode operation with suction taken from the refueling water storage tank (RWST). Only the injection mode is presented, as the injection mode has less NPSH margin than the recirculation mode.

3.2.3.1.1 Pump Flow Rates DG frequency affects both the head and flow values based on the pump affinity laws as follows:

Q2 = (N2IN1)*Q1 where, Q2 = Changed pump flow due to DG frequency variation Q1 = Nominal pump flow N2 = Changed pump speed due to DG frequency variation N1 = Nominal pump speed For the 59.8 Hz frequency, Q2 = (59.8/60.0)*Q1 = 0.997*Q1 For the 60.2 Hz frequency, Q2 = (60.2/60.0)*Q1 = 1.003*Q1 Therefore, a 0.2Hz change in DG frequency will change pump flow by + 0.33%.

3.2.3.1.2 NPSH The NPSHR for pumps increases as the speed and flowrate increase. The NPSHR is also affected by the increase in DG frequency as follows:

NPSHR2 = (N2Q2)4/3*NPSHR1 (N1Q1)4/3 Table 2 presents examples of NPSHR changes resulting from the DG frequency changes for the various pumps.

The results in Table 3 demonstrate the actual flow rates, NPSHA, NPSHR, and the NPSH Margin for the various pumps. The NPSHR values were obtained from the pump manufacturers NPSH curves at the flow values that are listed in Table 3. The DG increased frequency effects are included in these values. The results demonstrate that there is adequate positive margin for the pumps with the DG operating at the proposed revised frequencies.

CNL-16-001 E10 of 20

ENCLOSURE Table 2 Example NPSHR Changes System CS CC SI RHR NPSHR (ft) current 12.5 22 37.5 16 NPSHR (ft) at 12.6 22.1 37.8 16.1 60.2 Hz Table 3 NPSH Margin While Operating in RWST Injection Mode with Revised DG Frequency System CS CC SI RHR Pump Number A-A B-B A-A B-B A-A B-B A-A B-B Increased Pump 5100 5100 450 450 500 500 4200 4200 Flow (sgpm)

Pump Suction P 3.8 -2.5 6.7 6.8 1.9 1.6 -1.6 -3.9 (psig)

Pump Suction P 18.2 11.9 21.1 21.2 16.3 16.0 12.8 10.5 (psia)

Vapor P at 105°F 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 (psia)

NPSHA (psi) 17.1 10.8 20 20.1 15.2 14.9 11.7 9.4 NPSHA (ft) 39.7 25.1 46.5 46.7 35.3 34.6 27.2 21.8 NPSHR (ft) 12.1 12.1 18 18 19 19 15 15 NPSH margin (ft) 27.6 13 28.5 28.7 16.3 15.6 12.2 6.8 3.2.3.2 Pump Test Points The DG frequency variation of 59.8 Hz to 60.2 Hz has a negligible effect on plant operations for the above affected pumps based on the revised flow rates in Section 3.2.3.1. The flow change resulting from the DG frequency variation is limited to + 0.35%. The pump test acceptance criteria upper limit will be adjusted downward, and the lower limit will be adjusted upward in order to encompass the potential flow variation. The ASME OM Code inservice pump testing acceptance criteria provide assurance that the design basis is met.

3.2.3.3 Effect on Fans DG frequencies above/below 60 Hz directly increase/reduce motor speeds for fans.

Fan speed is directly proportional to fan flow. Therefore, increased/reduced motor speed will result in increased/reduced flows. For the 60.2 Hz DG frequency, fan flows are impacted as follows:

CNL-16-001 E11 of 20

ENCLOSURE Q2 = (60.2/60.0)*Q1 = 1.0033*Q1 and for the 59.8 Hz DG frequency, fan flows are impacted as follows; Q2 = (59.8/60.0)*Q1 = 0.9967*Q1 where:

Q2 = Changed fan flow due to DG frequency variation Q1 = Nominal fan flow From the above equations, fan flow could vary from nominal to about +0.33%. From the G-Spec (Reference 7), total airflow of a system can vary by +10% at the system fan. Thus, fan flows are within allowed tolerances due to sustained DG frequency variations.

3.2.3.4 Effect on Horsepower Requirements Horsepower requirements for a pump motor and fan increase by the cube of the speed change. Therefore, increased motor speed will result in increased horsepower demands on the diesels that feed the subject loads. The potential increase in load on the DGs due to operating frequency and voltage was evaluated to 60.2 Hz and 7260 V. The highest steady state loading was used which envelopes the other steady state loading scenarios.

Motor slip is defined as the difference between actual speed and synchronous speed an induction machine operates at as a percentage of the synchronous speed. A motor slip of about one percent increase in speed was calculated based on the increased DG voltage.

Motor speed varies directly with the system frequency as shown below:

1/2 = f1/f2 Thus, the speed impact of the frequency variation is (60 + 0.2)/60 or + 0.33%.

Therefore, the total impact of the voltage and frequency shift would be the sum of 1% + 0.33% which equals a 1.33% increase in motor speed.

As noted above, motor horsepower varies directly with the cube of the motor speed:

LoadNew = Loadold *Speed3 LoadNew = LoadOld

  • 1.01333 = LoadOld *1.040 Therefore, DG load would be increased by 4% if both the voltage and frequency were at their upper limits of 7260 V and 60.2 Hz. Because the DG fuel oil consumption is analyzed for a fully loaded diesel, the voltage and frequency variation do not adversely affect the fuel oil analysis.

CNL-16-001 E12 of 20

ENCLOSURE 3.2.4 Effect on Air Compressors and Chillers Air compressors and chillers are intermittently operated equipment designed to maintain an asset or volume between selected setpoints. Air compressors cycle on to charge a system to a high pressure setpoint, and then cycle off until the header pressure drops below the specified setpoint. Chillers cycle on and off to maintain a refrigerant fluid temperature between a specified range of temperatures. Because both air compressors and chillers work intermittently to maintain a fluid media in a range between two setpoints, the approximate +0.33% (+0.2 Hz) variation in DG frequency has a negligible effect on this type of equipment.

3.2.5 Effect on MOVs The affected MOVs were evaluated for frequency and voltage related to DG loading.

Motor torque and stroke time are two important parameters associated with MOV performance. The DG frequency affects the motor torque (Section 3.2.2) and speed.

Valve stroke time is inversely proportional to motor speed. Therefore, faster/slower motor speed would result in shorter/longer valve stroke times. For the 60.2 Hz frequency, valve stroke times vary as follows:

T2 = (60.2/60.0)*T1 = 1.0033*T1 Equation (1) and for the 59.8 to 60.0 Hz DG frequency range, valve stroke times are affected as follows; T2 = (59.8/60.0)*T1 = 0.9967*T1 Equation (2) where:

T2 = Changed stroke time due to DG frequency variation T1 = Nominal stroke time From equations (1) and (2), valve stroke times vary from nominal to approximately

+0.33%. For example, a valve that strokes in 30 seconds has the potential variation in stroke time of approximately +0.1 seconds. This potential variation is small in comparison to the valve stroke times documented in the inservice testing program and is essentially the same as the recorded resolution of the stop watches used for valve stroke time testing (i.e., 0.1 seconds). The majority of the active safety related MOVs stroke in 10 seconds or less; therefore, the variance in stroke time is

+ 0.03 seconds. For a 10-second valve, this is below the detectible threshold of the normal timing method. The longest of the safety related valve stroke times is up to 120 seconds for the valves involved in the automatic containment sump swap over.

The time variation is about + 0.4 seconds for these valves.

The MOV stroke time acceptance criteria for the ASME OM Code testing are adjusted to include the potential low frequency power. Accordingly, the design basis requirements for valve stroke time will be met. The minimum allowable DG voltage provides a voltage that is greater than the voltage used for the Generic Letter 89-10 analysis.

CNL-16-001 E13 of 20

ENCLOSURE Furthermore, based on the analyses in Section 3.2.2, the impact to torque is acceptable. In addition, there would not be a concern for water hammer due to the small change in stroke time. Therefore, there are no concerns with MOV operation due to the variation in DG frequency and voltage.

3.2.6 Effect on Electrical Equipment Most static loads are insensitive to changes in frequency and have a directly proportional change in current with terminal voltage, which is the opposite of the effects of voltage variation on induction motors. Only electronically controlled equipment, such as battery chargers, inverters and uninterruptible power supplies may be of concern at off nominal line frequency. The maximum allowable board voltage is 7260 V and the degraded voltage relay safety limit dropout setting is 6400 V. The variation in voltage from the DG of 6800 to 7260 V is much less than the range expected from the offsite source. Therefore, the variation in DG output voltage is bounded by voltage variations when off site power supplies the AC auxiliary power system.

3.2.6.1 Battery Chargers The battery charger regulation is maintained at +/-1% from no-load to full load with simultaneous changes in AC line voltage of +10% / -15% and changes in AC line frequency of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the battery chargers.

3.2.6.2 Hydrogen Igniters The hydrogen mitigation system (i.e., H2 igniters) does not use frequency sensitive components with the exception of the regulating transformer. The output is regulated to +/-1% from no-load to full load with AC line voltage changes of +/-10% and changes in AC frequency changes of +/-5%. Therefore, the variations in DG frequency will not impact the performance of the hydrogen mitigation system.

3.2.6.3 Instrumentation 120 V AC instrumentation circuits are designed with a +/-1% variation in frequency.

The variation in DG frequency is within this range.

3.3 Conclusion The results of these calculations determined that the proposed change in the DG frequency does not adversely affect the equipment powered by the DGs and their associated components described above. The calculations are available for NRC review. The DG output voltage and frequency range of 6800 to 7260 V and 59.8 to 60.2 Hz, respectively, will not affect the miscellaneous electrical equipment required to mitigate design basis events.

CNL-16-001 E14 of 20

ENCLOSURE

4.0 REGULATORY EVALUATION

4.1 Applicable Regulatory Requirements and Criteria The onsite standby ac power systems at SQN Units 1 and 2 are designed to comply with the following applicable regulations and requirements.

  • Title 10 of the Code of Federal Regulations (10 CFR) Part 50 (10 CFR 50),

Appendix A, General Design Criterion (GDC) 17, "Electric power systems," specifies that an onsite electric power system shall be provided to permit functioning of structures, systems, and components important to safety.

specifies that electric power systems important to safety shall be designed to permit appropriate periodic inspection and testing of important areas and features.

  • Regulatory Guide 1.6, Revision 0 (Reference 8), "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems," describes an acceptable degree of independence between redundant standby (onsite) power sources and between their distribution systems.
  • Regulatory Guide 1.9, Revision 0 (Reference 3). As noted in SQN UFSAR Section 8.3.1.2.1, SQN Units 1 and 2 comply with Regulatory Guide 1.9, Revision 0 except that voltage and frequency recovery requirements are taken from Regulatory Guide 1.9, Revision 1. As further noted in SQN UFSAR Section 8.3.1.2.1, an exception is taken for frequency immediately following DG breaker closure. The DG breaker is designed to automatically close at about 94 percent of nominal frequency.

This exception was accepted by the NRC in NUREG-1232 Volume 2 (Reference 9).

  • IEEE Standard 308-1971, "Criteria for Class 1E Power Systems for Nuclear Power Generating Stations," provides criteria for the determination of Class 1E power system design features and the requirements for their testing, surveillance, and documentation.

With the implementation of the proposed change, SQN Units 1 and 2 continues to meet the applicable regulations and requirements, subject to the previously approved exceptions.

4.2 Precedent The NRC has previously approved changes revising the TS SR acceptance criteria for steady state DG frequency.

1. Amendment Number 102 was issued for WBN Unit 1 in the Safety Evaluation dated September 17, 2015 (Reference 2). The Amendment made changes similar to those in this proposed license amendment request in that it revised the DG SR steady state frequency from 58.8 Hz and 61.2 Hz to 59.8 Hz and 60.1 Hz.
2. Amendment Numbers 227 and 105 were issued for Beaver Valley Power Station, Units 1 and 2, respectively, in the Safety Evaluation dated February 11, 2000 CNL-16-001 E15 of 20

ENCLOSURE (Reference 10). The Amendment corrected non-conservative TSs by clarifying the fuel oil storage volume requirements, increasing the load requirement for the single largest load rejection test, establishing criteria for maximum frequency that should not be exceeded following a load rejection, and revising the DG SR steady state frequency to 60.0 Hz and 60.6 Hz for Units 1 and 2 and 59.9 Hz and 60.3 Hz for Unit 2.

3. Amendment Number 129 was issued for the Palo Verde Nuclear Generating Station, Units 1, 2, and 3, in the Safety Evaluation dated October 4, 2000 (Reference 11).

The Amendment corrected non-conservative TSs by revising the current steady-state DG voltage limits of 3740 V and 4580 V and steady state frequency limit of 59.7 Hz and 61.2 Hz to a steady state voltage of 4000 V and <4377.2 V, and steady state frequency of 59.7 Hz and 60.7 Hz for the affected SR, except that for SR 3.8.1.2, the lower frequency limit is 58.8 Hz instead of the 59.7 Hz.

4. Amendment Numbers 309 and 291 were issued for the Donald C. Cook Nuclear Plant, Units 1 and 2, respectively, in the Safety Evaluation dated April 30, 2009 (Reference 12). The Amendment corrected non-conservative TSs by reducing the maximum DG steady state frequency in the associated SRs from 61.2 Hz to 60.5 Hz.

The Amendment also revised the minimum steady state voltage from 3740 V to 3910 V for certain TS SRs for consistency with the minimum steady state voltage specified in the acceptance criteria for other TS SRs, and reduced the criteria for maximum frequency that should not be exceeded following a load rejection.

5. Amendment Number 236 was issued for Crystal River, Unit 3 in the Safety Evaluation dated December 10, 2009 (Reference 13). The Amendment corrected non-conservative TSs by revising the DG steady state voltage to 4077 V and 4243 V and DG steady state frequency to 59.4 Hz and 60.6 Hz.
6. Amendment 204 was issued for the Wolf Creek Generating Station in the Safety Evaluation dated April 11, 2013 (Reference 14). The Amendment corrected non-conservative TSs by revising minimum DG steady state voltage to 3950 V and DG steady state frequency to 59.4 Hz and 60.6 Hz. The Amendment also revised the DG loading requirements to reflect the results of updated calculations.

4.3 Significant Hazards Consideration The proposed change would modify the Sequoyah Nuclear Plant (SQN), Units 1 and 2, Technical Specification (TS) 3.8.1, "AC Sources - Operating," by revising the acceptance criteria for the diesel generator (DG) steady state frequency acceptance criteria specified in TS Surveillance Requirements (SRs) 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18. The frequency will be changed from 58.8 Hz and 61.2 Hz to 59.8 Hz and 60.2 Hz for SRs 3.8.1.2, 3.8.1.7, 3.8.1.9, 3.8.1.11, 3.8.1.12, 3.8.1.15, and 3.8.1.18.

This proposed change also affects SR 3.8.1.3, because it requires successful performance of SR 3.8.1.2 or 3.8.1.7. TS 3.8.2, "AC Sources - Shutdown," is also affected because SR 3.8.2.1 requires the applicable SRs of TS 3.8.1 to be performed.

CNL-16-001 E16 of 20

ENCLOSURE TVA has evaluated whether or not a significant hazards consideration is involved with the proposed amendment(s) by focusing on the three standards set forth in 10 CFR 50.92, Issuance of amendment, as discussed below:

1. Does the proposed amendment involve a significant increase in the probability or consequence of an accident previously evaluated?

Response: No The DGs are required to be operable in the event of a design basis accident coincident with a loss of offsite power to mitigate the consequences of the accident. The DGs are not accident initiators and therefore these changes do not involve a significant increase in the probability of an accident previously evaluated.

The accident analyses assume that at least the boards in one load group are provided with power either from the offsite circuits or the DGs. The change proposed in this license amendment request will continue to assure that the DGs have the capacity and capability to assume their maximum design basis accident loads. The proposed change does not significantly alter how the plant would mitigate an accident previously evaluated.

The proposed change does not adversely affect accident initiators or precursors nor alter the design assumptions, conditions, and configuration of the facility or the manner in which the plant is operated and maintained. The proposed change does not adversely affect the ability of structures, systems, and components (SSC) to perform their intended safety function to mitigate the consequences of an initiating event within the assumed acceptance limits. The proposed change does not affect the source term, containment isolation, or radiological release assumptions used in evaluating the radiological consequences of any accident previously evaluated. Further, the proposed change does not increase the types and amounts of radioactive effluent that may be released offsite, nor significantly increase individual or cumulative occupational/public radiation exposure.

Therefore, the proposed change does not involve a significant increase in the probability or consequences of an accident previously evaluated.

2. Does the proposed amendment create the possibility of a new or different kind of accident from any accident previously evaluated?

Response: No.

The proposed change does not involve a change in the plant design, system operation, or the use of the DGs. The proposed change requires the DGs to meet SR acceptance criteria that envelope the actual demand requirements for the DGs during design basis conditions. These revised acceptance criteria continue to demonstrate the capability and capacity of the DGs to perform their required functions. There are no new failure modes or mechanisms created due to testing the DGs within the proposed acceptance criteria. Testing of the DGs at the proposed acceptance criteria does not involve any modification in the CNL-16-001 E17 of 20

ENCLOSURE operational limits or physical design of plant systems. There are no new accident precursors generated due to the proposed test loadings.

Therefore, the proposed change does not create the possibility of a new or different kind of accident from any accident previously evaluated.

3. Does the proposed amendment involve a significant reduction in a margin of safety?

Response: No.

The proposed change will continue to demonstrate that the DGs meet the TS definition of operability, that is, the proposed acceptance criteria will continue to demonstrate that the DGs will perform their safety function. The proposed testing will also continue to demonstrate the capability and capacity of the DGs to supply their required loads for mitigating a design basis accident.

The proposed change does not alter the manner in which safety limits, limiting safety system settings or limiting conditions for operation are determined. The safety analysis acceptance criteria are not affected by this change. The proposed change will not result in plant operation in a configuration outside the design basis.

Therefore, the proposed change does not involve a significant reduction in a margin of safety.

Based on the above, TVA concludes that the proposed amendment does not involve a significant hazards consideration under the standards set forth in 10 CFR 50.92 (c), and, accordingly, a finding of no significant hazards consideration is justified.

4.4 Conclusion In conclusion, based on the considerations discussed above, (1) there is reasonable assurance that the health and safety of the public will not be endangered by operation in the proposed manner, (2) such activities will be conducted in compliance with the Commissions regulations, and (3) the issuance of the amendment will not be inimical to the common defense and security or to the health and safety of the public.

5.0 ENVIRONMENTAL CONSIDERATION

A review has determined that the proposed amendment would change a requirement with respect to installation or use of a facility component located within the restricted area, as defined in 10 CFR 20, or would change an inspection or surveillance requirement. However, the proposed amendment does not involve (i) a significant hazards consideration, (ii) a significant change in the types or significant increase in the amounts of any effluents that may be released offsite, or (iii) a significant increase in individual or cumulative occupational radiation exposure. Accordingly, the proposed amendment meets the eligibility criterion for categorical exclusion set forth in 10 CFR 51.22(c)(9). Therefore, pursuant to 10 CFR 51.22(b), no environmental impact statement or environmental assessment need be prepared in connection with the proposed amendment.

CNL-16-001 E18 of 20

ENCLOSURE

6.0 REFERENCES

1. TVA Letter to NRC, CNL-14-218, Application to Modify Watts Bar Nuclear Plant, Unit 1 Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (SQN-TS-13-08), dated April 6, 2015 (ML15117A462)
2. NRC letter to TVA, Watts Bar Nuclear Plant, Unit 1 - Issuance of Amendment Regarding Modification To Technical Specification 3.8.1 Regarding Diesel Generator Steady State Frequency (TAC No. MF6153), dated September 17, 2015 (ML15230A155)
3. Regulatory Guide 1.9, Revision 0, "Selection of Diesel Generator Set Capacity for Standby Power Supplies"
4. NRC Administrative Letter 98-10, "Dispositioning of Technical Specifications that are Insufficient to Assure Plant Safety," dated December 29, 1998
5. Regulatory Guide 1.9, Revision 1, "Selection, Design, and Qualification of Diesel-Generator Units Used as Onsite Electric Power Systems at Nuclear Power Plants"
6. WCAP-17308-NP, Treatment of Diesel Generator (DG) Technical Specification Frequency and Voltage Tolerances, April 2012
7. G-Spec G-37 R5, Testing and Balancing of HVAC Systems During Installation, Modification, and Maintenance
8. Regulatory Guide 1.6, Revision 0, "Independence Between Redundant Standby (Onsite) Power Sources and Between Their Distribution Systems (Safety Guide 6)"
9. NUREG-1232, Volume 2, Safety Evaluation Report On Tennessee Valley Authority: Sequoyah Nuclear Performance Plan, dated May 1988
10. NRC Letter, "Beaver Valley 1 and 2 - Amendment for Revised Technical Specification Requirements for Emergency Diesel Generators (TAC Nos. MA4438 and MA4439)," dated February 11, 2000 (ML003684928)
11. NRC Letter, "Palo Verde Nuclear Generating Station, Units 1, 2, and 3 - Issuance of Amendments on Diesel Generator Steady-State Voltage and Frequency (TAC Nos. MA9214, MA9215, and MA9216)," dated October 4, 2000 (ML003758500)
12. NRC Letter, Donald C. Cook Nuclear Plant, Units 1 and 2 - Issuance of Amendment to Renewed Facility Operating License Regarding Technical Specification Change Relating to Diesel Generator Steady-State Parameters (TAC Nos. MD8773 and MD8774), dated April 30, 2009 (ML090630245)
13. NRC Letter, "Crystal River Unit 3 Nuclear Generating Plant - Issuance of Amendment Regarding Request to Revise the Technical Specification Surveillance Requirements for Emergency Diesel Generator Voltage and Frequency Limits (TAC No. ME0107), dated December 10, 2009 (ML092680285)

CNL-16-001 E19 of 20

ENCLOSURE

14. NRC Letter, "Wolf Creek Generating Station - Issuance of Amendment Re: Revise Technical Specification 3.8.1, "AC Sources - Operating" (TAC No. ME7674),"

dated April 11, 2013 (ML13077A147)

CNL-16-001 E20 of 20

ATTACHMENT 1 Proposed TS Changes (Mark-Ups) for SQN Units 1 and 2

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.2 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.

Verify each DG starts from standby conditions and In accordance achieves steady state voltage 6800 V and with the 7260 V, and frequency 58.8 Hz and 61.2 Hz. Surveillance Frequency Control Program 59.8 60.2 SR 3.8.1.3 ------------------------------NOTES-----------------------------

1. DG loadings may include gradual loading as recommended by the manufacturer.
2. Momentary transients outside the load range do not invalidate this test.
3. This Surveillance shall be conducted on only one DG at a time.
4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.

Verify each DG is synchronized and loaded and In accordance operates for 60 minutes at a load 3960 kW and with the 4400 kW. Surveillance Frequency Control Program SEQUOYAH - UNIT 1 3.8.1-6 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.4 Verify each engine-mounted day tank contains In accordance 250 gal of fuel oil. with the Surveillance Frequency Control Program SR 3.8.1.5 Check for and remove accumulated water from each In accordance engine-mounted day tank. with the Surveillance Frequency Control Program SR 3.8.1.6 Verify the fuel oil transfer system operates to In accordance transfer fuel oil from the storage system to the with the engine-mounted day tanks. Surveillance Frequency Control Program SR 3.8.1.7 ------------------------------NOTE-------------------------------

All DG starts may be preceded by an engine prelube period.

Verify each DG starts from standby condition and In accordance achieves: with the Surveillance

a. In 10 seconds, voltage 6800 V and Frequency frequency 58.8 Hz and Control Program
b. Steady state voltage 6800 V and 7260 V, and frequency 58.8 Hz and 61.2 Hz.

59.8 60.2 SEQUOYAH - UNIT 1 3.8.1-7 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.8 ------------------------------NOTES-----------------------------

1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.

Verify automatic and manual transfer of the power In accordance supply to each 6.9 kV Unit Board from the normal with the supply to the alternate supply. Surveillance Frequency Control Program SR 3.8.1.9 ------------------------------NOTE------------------------------

If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.

Under this condition the power factor shall be maintained as close to the limit as practicable.

Verify each DG rejects a load greater than or equal In accordance to its associated single largest post-accident load, with the and: Surveillance Frequency

a. Following load rejection, the frequency is Control Program 66.5 Hz,
b. Within 3 seconds following load rejection, the voltage is 6800 V and 7260 V, and
c. Within 3 seconds following load rejection, the frequency is 58.8 Hz and 61.2 Hz.

SEQUOYAH - UNIT 1 59.8 60.2 3.8.1-8 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.11 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal: with the Surveillance

a. De-energization of shutdown boards, Frequency Control Program
b. Load shedding from shutdown boards,
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected shutdown loads through load sequence timers,
3. Maintains steady state voltage 6800 V and 7260 V,
4. Maintains steady state frequency 58.8 Hz and 61.2 Hz, and
5. Supplies permanently connected and auto-connected shutdown loads for 59.8 60.2 5 minutes.

SEQUOYAH - UNIT 1 3.8.1-10 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.12 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated Engineered Safety In accordance Feature (ESF) actuation signal each DG auto-starts with the from standby condition and: Surveillance Frequency

a. In 10 seconds after auto-start and during Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
b. Achieves steady state voltage 6800 V and 7260 V and frequency 58.8 Hz and 61.2 Hz,
c. Operates for 5 minutes, 59.8 60.2 d. Permanently connected loads remain energized from the offsite power system, and
e. Emergency loads are energized from the offsite power system.

SEQUOYAH - UNIT 1 3.8.1-11 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.15 ------------------------------NOTES-----------------------------

1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> loaded 3960 kW and 4400 kW and 2140 kvar and 2370 kvar.

Momentary transients outside of load range do not invalidate this test.

2. All DG starts may be preceded by an engine prelube period.

Verify each DG starts and achieves: In accordance with the

a. In 10 seconds, voltage 6800 V and Surveillance frequency 58.8 Hz and Frequency Control Program
b. Steady state voltage 6800 V, and 7260 V and frequency 58.8 Hz and 61.2 Hz.

SR 3.8.1.16 ------------------------------NOTE-------------------------------

For DGs 59.8 1A-A and 1B-B, 60.2this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify each DG: In accordance with the

a. Synchronizes with offsite power source while Surveillance loaded with emergency loads upon a simulated Frequency restoration of offsite power, Control Program
b. Transfers loads to offsite power source, and
c. Returns to ready-to-load operation.

SEQUOYAH - UNIT 1 3.8.1-13 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.18 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal in conjunction with an actual or simulated with the ESF actuation signal: Surveillance Frequency

a. De-energization of shutdown boards, Control Program
b. Load shedding from shutdown boards, and
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected emergency loads through load sequence timers,
3. Achieves steady state voltage 6800 V and 7260 V,
4. Achieves steady state frequency 58.8 Hz and 61.2 Hz, and
5. Supplies permanently connected and auto-connected emergency 59.8 loads for 60.2 5 minutes.

SEQUOYAH - UNIT 1 3.8.1-15 Amendment 334

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.2 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.

Verify each DG starts from standby conditions and In accordance achieves steady state voltage 6800 V and with the 7260 V, and frequency 58.8 Hz and 61.2 Hz. Surveillance Frequency Control Program 59.8 60.2 SR 3.8.1.3 ------------------------------NOTES-----------------------------

1. DG loadings may include gradual loading as recommended by the manufacturer.
2. Momentary transients outside the load range do not invalidate this test.
3. This Surveillance shall be conducted on only one DG at a time.
4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.

Verify each DG is synchronized and loaded and In accordance operates for 60 minutes at a load 3960 kW and with the 4400 kW. Surveillance Frequency Control Program SEQUOYAH - UNIT 2 3.8.1-6 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.4 Verify each engine-mounted day tank contains In accordance 250 gal of fuel oil. with the Surveillance Frequency Control Program SR 3.8.1.5 Check for and remove accumulated water from each In accordance engine-mounted day tank. with the Surveillance Frequency Control Program SR 3.8.1.6 Verify the fuel oil transfer system operates to In accordance transfer fuel oil from the storage system to the with the engine-mounted day tanks. Surveillance Frequency Control Program SR 3.8.1.7 ------------------------------NOTE-------------------------------

All DG starts may be preceded by an engine prelube period.

Verify each DG starts from standby condition and In accordance achieves: with the Surveillance

a. In 10 seconds, voltage 6800 V and Frequency frequency 58.8 Hz and Control Program
b. Steady state voltage 6800 V and 7260 V, and frequency 58.8 Hz and 61.2 Hz.

59.8 60.2 SEQUOYAH - UNIT 2 3.8.1-7 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.8 ------------------------------NOTES-----------------------------

1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.

Verify automatic and manual transfer of the power In accordance supply to each 6.9 kV Unit Board from the normal with the supply to the alternate supply. Surveillance Frequency Control Program SR 3.8.1.9 ------------------------------NOTE-------------------------------

If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.

Under this condition the power factor shall be maintained as close to the limit as practicable.

Verify each DG rejects a load greater than or equal In accordance to its associated single largest post-accident load, with the and: Surveillance Frequency

a. Following load rejection, the frequency is Control Program 66.5 Hz,
b. Within 3 seconds following load rejection, the voltage is 6800 V and 7260 V, and
c. Within 3 seconds following load rejection, the frequency is 58.8 Hz and 61.2 Hz.

59.8 60.2 SEQUOYAH - UNIT 2 3.8.1-8 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.11 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal: with the Surveillance

a. De-energization of shutdown boards, Frequency Control Program
b. Load shedding from shutdown boards,
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected shutdown loads through load sequence timers,
3. Maintains steady state voltage 6800 V and 7260 V,
4. Maintains steady state frequency 58.8 Hz and 61.2 Hz, and
5. Supplies permanently connected and auto-connected shutdown loads for 59.8 60.2 5 minutes.

SEQUOYAH - UNIT 2 3.8.1-10 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.12 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated Engineered Safety In accordance Feature (ESF) actuation signal each DG auto-starts with the from standby condition and: Surveillance Frequency

a. In 10 seconds after auto-start and during Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
b. Achieves steady state voltage 6800 V and 7260 V and frequency 58.8 Hz and 61.2 Hz,
c. Operates for 5 minutes, 59.8
d. Permanently connected loads remain energized 60.2 from the offsite power system, and
e. Emergency loads are energized from the offsite power system.

SEQUOYAH - UNIT 2 3.8.1-11 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.15 ------------------------------NOTES-----------------------------

1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> loaded 3960 kW and 4400 kW and 2140 kvar and 2370 kvar.

Momentary transients outside of load range do not invalidate this test.

2. All DG starts may be preceded by an engine prelube period.

Verify each DG starts and achieves: In accordance with the

a. In 10 seconds, voltage 6800 V and Surveillance frequency 58.8 Hz and Frequency Control Program
b. Steady state voltage 6800 V, and 7260 V and frequency 58.8 Hz and 61.2 Hz.

SR 3.8.1.16 ------------------------------NOTE-------------------------------

For DGs 59.82A-A and 2B-B, this Surveillance shall 60.2not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify each DG: In accordance with the

a. Synchronizes with offsite power source while Surveillance loaded with emergency loads upon a simulated Frequency restoration of offsite power, Control Program
b. Transfers loads to offsite power source, and
c. Returns to ready-to-load operation.

SEQUOYAH - UNIT 2 3.8.1-13 Amendment 327

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.18 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal in conjunction with an actual or simulated with the ESF actuation signal: Surveillance Frequency

a. De-energization of shutdown boards, Control Program
b. Load shedding from shutdown boards, and
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected emergency loads through load sequence timers,
3. Achieves steady state voltage 6800 V and 7260 V,
4. Achieves steady state frequency 58.8 Hz and 61.2 Hz, and
5. Supplies permanently connected and auto-connected emergency loads 59.8 for 5 minutes. 60.2 SEQUOYAH - UNIT 2 3.8.1-15 Amendment 327

ATTACHMENT 2 Proposed TS Bases Changes (Mark-Ups) for SQN Units 1 and 2 (For Information Only)

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).

Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).

Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.

The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.

The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/- 2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).

SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3).

These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.

SEQUOYAH - UNIT 1 B 3.8.1-16 Revision 45

AC Sources - Operating B 3.8.1 During this testing, the diesel is BASES not in an accident mode and the frequency is controlled by SURVEILLANCE REQUIREMENTS (continued) the operator instead of the governors accident speed SR 3.8.1.2 and SR 3.8.1.7 reference.

These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.

To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.

For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.

In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.

SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).

The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.

Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.

In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 1 B 3.8.1-17 Revision 45

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:

a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
b. Tripping its associated single largest post-accident load with the DG solely supplying the board. and Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejectionmaximum test is transient acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.

The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.

SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.

These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to 0.89 results in voltages on the emergency boards that are too high.

SEQUOYAH - UNIT 1 B 3.8.1-21 Revision 45

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).

Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).

Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.

The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.

The specified minimum and maximum frequencies of the DG are 58.8 Hz and 61.2 Hz, respectively. These values are equal to +/- 2% of the 60 Hz nominal frequency and are derived from the recommendations given in Regulatory Guide 1.9 (Ref. 3).

SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program. The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3).

These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.

SEQUOYAH - UNIT 2 B 3.8.1-16 Revision 44

AC Sources - Operating B 3.8.1 During this testing, the diesel is not in an accident mode and BASES the frequency is controlled by the operator instead of the SURVEILLANCE REQUIREMENTS (continued) governors accident speed reference.

SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.

To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.

For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.

In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.

SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).

The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.

Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.

In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 2 B 3.8.1-17 Revision 45

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:

a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
b. Tripping its associated single largest post-accident load with the DG solely supplying the board. and Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejectionmaximum test is transient acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.

The time, voltage, and frequency tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and frequency specified are consistent with the design range of the equipment powered by the DG.

SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.

These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to 0.89 results in voltages on the emergency boards that are too high.

SEQUOYAH - UNIT 2 B 3.8.1-21 Revision 45

ATTACHMENT 3 Proposed TS Changes (Final Typed) for SQN Units 1 and 2

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.2 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.

Verify each DG starts from standby conditions and In accordance achieves steady state voltage 6800 V and with the 7260 V, and frequency 59.8 Hz and 60.2 Hz. Surveillance Frequency Control Program SR 3.8.1.3 ------------------------------NOTES-----------------------------

1. DG loadings may include gradual loading as recommended by the manufacturer.
2. Momentary transients outside the load range do not invalidate this test.
3. This Surveillance shall be conducted on only one DG at a time.
4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.

Verify each DG is synchronized and loaded and In accordance operates for 60 minutes at a load 3960 kW and with the 4400 kW. Surveillance Frequency Control Program SEQUOYAH - UNIT 1 3.8.1-6 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.4 Verify each engine-mounted day tank contains In accordance 250 gal of fuel oil. with the Surveillance Frequency Control Program SR 3.8.1.5 Check for and remove accumulated water from each In accordance engine-mounted day tank. with the Surveillance Frequency Control Program SR 3.8.1.6 Verify the fuel oil transfer system operates to In accordance transfer fuel oil from the storage system to the with the engine-mounted day tanks. Surveillance Frequency Control Program SR 3.8.1.7 ------------------------------NOTE-------------------------------

All DG starts may be preceded by an engine prelube period.

Verify each DG starts from standby condition and In accordance achieves: with the Surveillance

a. In 10 seconds, voltage 6800 V and Frequency frequency 58.8 Hz and Control Program
b. Steady state voltage 6800 V and 7260 V, and frequency 59.8 Hz and 60.2 Hz.

SEQUOYAH - UNIT 1 3.8.1-7 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.8 ------------------------------NOTES-----------------------------

1. For the 1A, 1B, 1C, and 1D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.

Verify automatic and manual transfer of the power In accordance supply to each 6.9 kV Unit Board from the normal with the supply to the alternate supply. Surveillance Frequency Control Program SR 3.8.1.9 ------------------------------NOTE------------------------------

If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.

Under this condition the power factor shall be maintained as close to the limit as practicable.

Verify each DG rejects a load greater than or equal In accordance to its associated single largest post-accident load, with the and: Surveillance Frequency

a. Following load rejection, the frequency is Control Program 66.5 Hz,
b. Within 3 seconds following load rejection, the voltage is 6800 V and 7260 V, and
c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and 60.2 Hz.

SEQUOYAH - UNIT 1 3.8.1-8 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.11 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal: with the Surveillance

a. De-energization of shutdown boards, Frequency Control Program
b. Load shedding from shutdown boards,
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected shutdown loads through load sequence timers,
3. Maintains steady state voltage 6800 V and 7260 V,
4. Maintains steady state frequency 59.8 Hz and 60.2 Hz, and
5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.

SEQUOYAH - UNIT 1 3.8.1-10 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.12 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated Engineered Safety In accordance Feature (ESF) actuation signal each DG auto-starts with the from standby condition and: Surveillance Frequency

a. In 10 seconds after auto-start and during Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
b. Achieves steady state voltage 6800 V and 7260 V and frequency 59.8 Hz and 60.2 Hz,
c. Operates for 5 minutes,
d. Permanently connected loads remain energized from the offsite power system, and
e. Emergency loads are energized from the offsite power system.

SEQUOYAH - UNIT 1 3.8.1-11 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.15 ------------------------------NOTES-----------------------------

1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> loaded 3960 kW and 4400 kW and 2140 kvar and 2370 kvar.

Momentary transients outside of load range do not invalidate this test.

2. All DG starts may be preceded by an engine prelube period.

Verify each DG starts and achieves: In accordance with the

a. In 10 seconds, voltage 6800 V and Surveillance frequency 58.8 Hz and Frequency Control Program
b. Steady state voltage 6800 V, and 7260 V and frequency 59.8 Hz and 60.2 Hz.

SR 3.8.1.16 ------------------------------NOTE-------------------------------

For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify each DG: In accordance with the

a. Synchronizes with offsite power source while Surveillance loaded with emergency loads upon a simulated Frequency restoration of offsite power, Control Program
b. Transfers loads to offsite power source, and
c. Returns to ready-to-load operation.

SEQUOYAH - UNIT 1 3.8.1-13 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.18 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 1A-A and 1B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal in conjunction with an actual or simulated with the ESF actuation signal: Surveillance Frequency

a. De-energization of shutdown boards, Control Program
b. Load shedding from shutdown boards, and
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected emergency loads through load sequence timers,
3. Achieves steady state voltage 6800 V and 7260 V,
4. Achieves steady state frequency 59.8 Hz and 60.2 Hz, and
5. Supplies permanently connected and auto-connected emergency loads for 5 minutes.

SEQUOYAH - UNIT 1 3.8.1-15 Amendment 33X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.2 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period and followed by a warmup period prior to loading.
2. A modified DG start involving idling and gradual acceleration to synchronous speed may be used for this SR as recommended by the manufacturer. When modified start procedures are not used, the time, voltage, and frequency tolerances of SR 3.8.1.7 must be met.

Verify each DG starts from standby conditions and In accordance achieves steady state voltage 6800 V and with the 7260 V, and frequency 59.8 Hz and 60.2 Hz. Surveillance Frequency Control Program SR 3.8.1.3 ------------------------------NOTES-----------------------------

1. DG loadings may include gradual loading as recommended by the manufacturer.
2. Momentary transients outside the load range do not invalidate this test.
3. This Surveillance shall be conducted on only one DG at a time.
4. This SR shall be preceded by and immediately follow without shutdown a successful performance of SR 3.8.1.2 or SR 3.8.1.7.

Verify each DG is synchronized and loaded and In accordance operates for 60 minutes at a load 3960 kW and with the 4400 kW. Surveillance Frequency Control Program SEQUOYAH - UNIT 2 3.8.1-6 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.4 Verify each engine-mounted day tank contains In accordance 250 gal of fuel oil. with the Surveillance Frequency Control Program SR 3.8.1.5 Check for and remove accumulated water from each In accordance engine-mounted day tank. with the Surveillance Frequency Control Program SR 3.8.1.6 Verify the fuel oil transfer system operates to In accordance transfer fuel oil from the storage system to the with the engine-mounted day tanks. Surveillance Frequency Control Program SR 3.8.1.7 ------------------------------NOTE-------------------------------

All DG starts may be preceded by an engine prelube period.

Verify each DG starts from standby condition and In accordance achieves: with the Surveillance

a. In 10 seconds, voltage 6800 V and Frequency frequency 58.8 Hz and Control Program
b. Steady state voltage 6800 V and 7260 V, and frequency 59.8 Hz and 60.2 Hz.

SEQUOYAH - UNIT 2 3.8.1-7 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.8 ------------------------------NOTES-----------------------------

1. For the 2A, 2B, 2C, and 2D Unit Boards, this Surveillance shall not normally be performed in MODE 1 or 2. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.
2. Transfer capability is only required to be met for 6.9 kV Unit Boards that require normal and alternate power supplies.

Verify automatic and manual transfer of the power In accordance supply to each 6.9 kV Unit Board from the normal with the supply to the alternate supply. Surveillance Frequency Control Program SR 3.8.1.9 ------------------------------NOTE-------------------------------

If performed with the DG synchronized with offsite power, it shall be performed at a power factor 0.89. However, if grid conditions do not permit, the power factor limit is not required to be met.

Under this condition the power factor shall be maintained as close to the limit as practicable.

Verify each DG rejects a load greater than or equal In accordance to its associated single largest post-accident load, with the and: Surveillance Frequency

a. Following load rejection, the frequency is Control Program 66.5 Hz,
b. Within 3 seconds following load rejection, the voltage is 6800 V and 7260 V, and
c. Within 3 seconds following load rejection, the frequency is 59.8 Hz and 60.2 Hz.

SEQUOYAH - UNIT 2 3.8.1-8 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.11 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal: with the Surveillance

a. De-energization of shutdown boards, Frequency Control Program
b. Load shedding from shutdown boards,
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected shutdown loads through load sequence timers,
3. Maintains steady state voltage 6800 V and 7260 V,
4. Maintains steady state frequency 59.8 Hz and 60.2 Hz, and
5. Supplies permanently connected and auto-connected shutdown loads for 5 minutes.

SEQUOYAH - UNIT 2 3.8.1-10 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.12 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1 or 2. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated Engineered Safety In accordance Feature (ESF) actuation signal each DG auto-starts with the from standby condition and: Surveillance Frequency

a. In 10 seconds after auto-start and during Control Program tests, achieves voltage 6800 V and frequency 58.8 Hz,
b. Achieves steady state voltage 6800 V and 7260 V and frequency 59.8 Hz and 60.2 Hz,
c. Operates for 5 minutes,
d. Permanently connected loads remain energized from the offsite power system, and
e. Emergency loads are energized from the offsite power system.

SEQUOYAH - UNIT 2 3.8.1-11 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.15 ------------------------------NOTES-----------------------------

1. This Surveillance shall be performed within 5 minutes of shutting down the DG after the DG has operated 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br /> loaded 3960 kW and 4400 kW and 2140 kvar and 2370 kvar.

Momentary transients outside of load range do not invalidate this test.

2. All DG starts may be preceded by an engine prelube period.

Verify each DG starts and achieves: In accordance with the

a. In 10 seconds, voltage 6800 V and Surveillance frequency 58.8 Hz and Frequency Control Program
b. Steady state voltage 6800 V, and 7260 V and frequency 59.8 Hz and 60.2 Hz.

SR 3.8.1.16 ------------------------------NOTE-------------------------------

For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, this Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify each DG: In accordance with the

a. Synchronizes with offsite power source while Surveillance loaded with emergency loads upon a simulated Frequency restoration of offsite power, Control Program
b. Transfers loads to offsite power source, and
c. Returns to ready-to-load operation.

SEQUOYAH - UNIT 2 3.8.1-13 Amendment 32X

AC Sources - Operating 3.8.1 SURVEILLANCE REQUIREMENTS (continued)

SURVEILLANCE FREQUENCY SR 3.8.1.18 ------------------------------NOTES-----------------------------

1. All DG starts may be preceded by an engine prelube period.
2. For DGs 2A-A and 2B-B, this Surveillance shall not normally be performed in MODE 1, 2, 3, or 4. However, portions of the Surveillance may be performed to reestablish OPERABILITY provided an assessment determines the safety of the plant is maintained or enhanced. Credit may be taken for unplanned events that satisfy this SR.

Verify on an actual or simulated loss of offsite power In accordance signal in conjunction with an actual or simulated with the ESF actuation signal: Surveillance Frequency

a. De-energization of shutdown boards, Control Program
b. Load shedding from shutdown boards, and
c. DG auto-starts from standby condition and:
1. Energizes permanently connected loads in 10 seconds,
2. Energizes auto-connected emergency loads through load sequence timers,
3. Achieves steady state voltage 6800 V and 7260 V,
4. Achieves steady state frequency 59.8 Hz and 60.2 Hz, and
5. Supplies permanently connected and auto-connected emergency loads for 5 minutes.

SEQUOYAH - UNIT 2 3.8.1-15 Amendment 32X

ATTACHMENT 4 Proposed TS Bases Changes (Final Typed) for SQN Units 1 and 2 (For Information Only)

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).

Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).

Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.

The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.

The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.

SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 1 B 3.8.1-16 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.

To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.

For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.

In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.

SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).

The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used.

During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governors accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.

Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.

In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 1 B 3.8.1-17 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:

a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
b. Tripping its associated single largest post-accident load with the DG solely supplying the board.

Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.

The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.

SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.

These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to 0.89 results in voltages on the emergency boards that are too high.

SEQUOYAH - UNIT 1 B 3.8.1-21 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE The AC sources are designed to permit inspection and testing of all REQUIREMENTS important areas and features, especially those that have a standby function, in accordance with 10 CFR 50, Appendix A, GDC 18 (Ref. 8).

Periodic component tests are supplemented by extensive functional tests during refueling outages (under simulated accident conditions). The SRs for demonstrating the OPERABILITY of the DGs are in accordance with the recommendations of Regulatory Guide 1.9 (Ref. 3) and Regulatory Guide 1.108 (Ref. 9).

Where the SRs discussed herein specify voltage and frequency tolerances, the following is applicable. The minimum steady state output voltage of 6210 V is 90% of the nominal 6900 V output voltage. This value, which is specified in ANSI C84.1 (Ref. 10), allows for voltage drop to the terminals of 6600 V motors whose minimum operating voltage is specified as 90% or 5940 V. It also allows for voltage drops to motors and other equipment down through the 120 V level where minimum operating voltage is also usually specified as 90% of name plate rating.

The specified maximum steady state output voltage of 7260 V is equal to the maximum operating voltage specified for 6600 V motors. It ensures that for a lightly loaded distribution system, the voltage at the terminals of 6600 V motors is no more than the maximum rated operating voltages.

The steady state minimum and maximum frequency values are 59.8 Hz and 60.2 Hz, which are consistent with the recommendations in Regulatory Guide 1.9 (Ref. 3). These values ensure that the safety related plant equipment powered from the DGs is capable of performing its safety functions.

SR 3.8.1.1 This SR ensures proper circuit continuity for the offsite AC electrical power supply to the onsite distribution network and availability of offsite AC electrical power. The breaker alignment verifies that each breaker is in its correct position to ensure that distribution buses and loads are connected to their preferred power source, and that appropriate independence of offsite circuits is maintained.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 2 B 3.8.1-16 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.2 and SR 3.8.1.7 These SRs help to ensure the availability of the standby electrical power supply to mitigate DBAs and transients and to maintain the unit in a safe shutdown condition.

To minimize the wear on moving parts that do not get lubricated when the engine is not running, these SRs are modified by a Note (Note 1 for SR 3.8.1.2 and Note for SR 3.8.1.7) to indicate that all DG starts for these Surveillances may be preceded by an engine prelube period and followed by a warmup period prior to loading.

For the purposes of SR 3.8.1.2 and SR 3.8.1.7 testing, the DGs are started from standby conditions. Standby conditions for a DG mean that the diesel engine coolant and oil are being continuously circulated and temperature is being maintained consistent with manufacturer recommendations.

In order to reduce stress and wear on diesel engines, the manufacturer recommends a modified start in which the starting speed of DGs is limited, warmup is limited to this lower speed, and the DGs are gradually accelerated to synchronous speed prior to loading. These start procedures are the intent of Note 2.

SR 3.8.1.7 requires that the DG starts from standby conditions and achieves required voltage and frequency within 10 seconds. The 10 second start requirement supports the assumptions of the design basis LOCA analysis in the UFSAR, Chapter 15 (Ref. 5).

The 10 second start requirement is not applicable to SR 3.8.1.2 (see Note 2) when a modified start procedure as described above is used.

During this testing, the diesel is not in an accident mode and the frequency is controlled by the operator instead of the governors accident speed reference. If a modified start is not used, the 10 second start requirement of SR 3.8.1.7 applies.

Since SR 3.8.1.7 requires a 10 second start, it is more restrictive than SR 3.8.1.2, and it may be performed in lieu of SR 3.8.1.2.

In addition to the SR requirements, the time for the DG to reach steady state operation, unless the modified DG start method is employed, is periodically monitored and the trend evaluated to identify degradation of governor and voltage regulator performance.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

SEQUOYAH - UNIT 2 B 3.8.1-17 Revision XX

AC Sources - Operating B 3.8.1 BASES SURVEILLANCE REQUIREMENTS (continued)

SR 3.8.1.9 Each DG is provided with an engine overspeed trip to prevent damage to the engine. Recovery from the transient caused by the loss of a large load could cause diesel engine overspeed, which, if excessive, might result in a trip of the engine. This Surveillance demonstrates the DG load response characteristics and capability to reject the largest single load (600 kW) without exceeding predetermined voltage and frequency and while maintaining a specified margin to the overspeed trip. This Surveillance may be accomplished by:

a. Tripping the DG output breaker with the DG carrying greater than or equal to its associated single largest post-accident load while paralleled to offsite power, or while solely supplying the board, or
b. Tripping its associated single largest post-accident load with the DG solely supplying the board.

Consistent with Regulatory Guide 1.9 (Ref. 3), the load rejection test is acceptable if the increase in diesel speed does not exceed 75% of the difference between synchronous speed and the overspeed trip setpoint, or 15% above synchronous speed, whichever is lower.

The time and voltage tolerances specified in this SR are derived from Regulatory Guide 1.9 (Ref. 3) recommendations for response during load sequence intervals. The 3 seconds specified is equal to 60% of a typical 5 second load sequence interval associated with sequencing of the largest load. The voltage and maximum transient frequency specified are consistent with the design range of the equipment powered by the DG.

SR 3.8.1.9.a corresponds to the maximum frequency excursion, while SR 3.8.1.9.b and SR 3.8.1.9.c are steady state voltage and frequency values to which the system must recover following load rejection.

The Surveillance Frequency is controlled under the Surveillance Frequency Control Program.

This SR is modified by a Note. The Note ensures that the DG is tested under load conditions that are as close to design basis conditions as possible. When synchronized with offsite power, testing should be performed at a power factor of 0.89. This power factor is representative of the actual inductive loading a DG would see under design basis accident conditions. Under certain conditions, however, the Note allows the Surveillance to be conducted at a power factor other than 0.89.

These conditions occur when grid voltage is high, and the additional field excitation needed to get the power factor to 0.89 results in voltages on the emergency boards that are too high.

SEQUOYAH - UNIT 2 B 3.8.1-21 Revision XX