Revision as of 04:25, 14 July 2019

Text

Third Ten Year Inservice Inspection Interval Requests for Relief 02-004 and 02-005, Response to RAI
	ML031550538
Person / Time
Site:	Oconee
Issue date:	05/15/2003
From:	Rosalyn Jones; Duke Power Co
To:	; Document Control Desk, Office of Nuclear Reactor Regulation
References
	-RFPFR
	Download: ML031550538 (31)
	v • d • e

Duke R. A. JONES ldwPowere Vice President A Duke Energy Company Duke Power 29672 / Oconee Nuclear Site 7800 Rochester Highway Seneca, SC 29672 864 885 3158 864 885 3564 fax May 15, 2003 U.S. Nuclear Regulatory Commission Document Control Desk Washington, DC 20555

Subject:

Duke Energy Oconee Nuclear Station, Unit 1 Docket Nos. 50-269 Third Ten Year Inservice Inspection Interval Requests for Relief No.02-004 and 02-005 On July 29, 2002, Duke Energy Corporation (Duke) submitted Requests for Relief No.02-004 and No.02-005. These requests sought to address twenty (20) limited ultrasonic examinations on Reactor Vessel welds and seventeen (17)limited ultrasonic examinations on other welds specified in the request.During examination of the subject Unit 1 welds, the ultrasonic examination coverage did not meet the 90%examination requirements of Code Case N-460. Duke personnel determined it was impractical to meet the volumetric requirements for ultrasonic examination of the specified welds due to piping/vessel geometry, interferences, and existing examination technology.

Therefore, Duke Energy requested that the NRC grant relief as authorized under 10 CFR 50.55a(g)(6)(i).

Subsequently the staff requested additional information to facilitate their review of the requests.

Accordingly, revised submittals are attached in order to clarify our requests and to provide additional information requested by the staff.If there are any questions or further information is needed you may contact R. P. Todd at (864) 885-3418.www. duke-energy.

com U. S. Nuclear Regulatory Commission May 15, 2003 Page 2 Very truly yours, R. A. Jones Site Vice President Attachments xc w/att: L. A. Reyes, Regional Administrator U.S. Nuclear Regulatory Commission, Region II Atlanta Federal Center 61 Forsyth St., SWW, Suite 23T85 Atlanta, GA 30303 L. N. Olshan, Project Manager, Section 1 Project Directorate II Division of Licensing Project Management Office of Nuclear Reactor Regulation U. S. Nuclear Regulatory Commission Washington, DC 20555-0001 xc(w/o attch): M. C. Shannon Senior NRC Resident Inspector Oconee Nuclear Station Mr. Henry Porter Division of Radioactive Waste Management Bureau of Land and Waste Management SC Dept. of Health & Environmental Control 2600 Bull St.Columbia, SC 29201 Relief Request 02-004 Rev. 1 Page 1 of 9, Proposed Relief in Accordance with 10 CFR 50.55a(g)(5)(iii)

Inservice Inspection Impracticality Duke Energy Corporation Oconee Nuclear Station -Unit 1 (EOC-20)Third 10-Year Interval -Inservice Inspection Plan Interval Start Date = 7-15-1994 Interval End Date = 1-1-2004 ASME Section XI Code -1989 Edition with No Addenda I. II. & III. IV. V. VI. VII.Limited System / Code Requirement from Which Basis for Relief Alternate Justification Implementation Area/Weld Component for Which Relief is Requested:

Examinations or for Granting Schedule I.D. Relief Is Requested:

100% Exam Volume Coverage Testing Relief Number Area or Weld to be Exam Category Examined Item No.Fig. No.Limitation Percentage I-RPV-WR34 NC System Exam Category B-A See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. B01.01 1.005 "A" "G" "1T "K" Lower Shell to Lower Fig. IWB-2500-1 Head Ring 36% Volume Coverage Circumferential Weld 1-RPV-WR35 NC System Exam Category B-A See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. BO1.021.003 "A" "G" "H "K" Lower Head Cap to Fig. IWB-2500-3 Lower Head Ring 42% Volume Coverage Circumferential Weld 1-RPV-WR13 NC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. B03.090.001 "B" "G" "I" "K" Outlet Nozzle-to-Vessel Fig. IWB-2500-7(a)

Weld @ 90° 82% Volume Coverage (UT from vessel I.D.)1-RPV- NC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph WR13A Reactor Vessel Item No. B03.090.002 "B" "G" "I" "K" Outlet Nozzle-to-Vessel Fig. IWB-2500-7(a)

Weld @ 270° 82% Volume Coverage (UT from vessel I.D.)

Relief Request 02-004 Rev. 1 Page 2 of 9, I. II. & III. IV. V. VI. VII.Limited System / Code Requirement from Which Basis for Relief Alternate Justification Implementation Area/Weld Component for Which Relief is Requested:

Examinations or for Granting Schedule I.D. Relief is Requested:

100% Exam Volume Coverage Testing Relief Number Area or Weld to be Exam Category Examined Item No.Fig. No.Limitation Percentage 1-RPV-WR54 NC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Fig. IWB-2500-7(a) "C" "G" "r' "K Core Flood Item No. B03.090.007 Nozzle-to-Vessel Weld (UT from vessel I.D.)@ O 81% Volume Coverage Item No. B03.090.007A (UT from nozzle ID)0% Volume Coverage (not able to scan)1-RPV- NC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph WR54A Reactor Vessel Fig. IWB-2500-7(a) "C" G "I" "K" Core Flood Item No. B03.090.008 Nozzle-to-Vessel Weld (UT from vessel ID)@ 1800 81% Volume Coverage Item No. B03.090.008A (UT from nozzle ID)0% Volume Coverage (not able to scan)1-RPV-WR54 NC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. B03.100.007 "D" "G" "I" "K" Core Flood Nozzle Fig. IWB-2500-7(a)

Inside Radius Section 52% Volume Coverage@00 1-RPV- NC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph WR54A Reactor Vessel Item No. B03.100.008 "D" "G" "I" "K" Core Flood Nozzle Fig. IWB-2500-7(a)

Inside Radius Section 52% Volume Coverage@ 1800 I r T r r I. II. & III. IV. V. VI. VII.Limited System / Code Requirement from Which Basis for Relief Alternate Justification Implementation Area/Weld Component for Which Relief Is Requested:

Examinations or for Granting Schedule I.D. Relief is Requested:

100% Exam Volume Coverage Testing Relief Number Area or Weld to be Exam Category Examined Item No.Fig. No.Limitation Percentage 1-RPV-WR53 NC System Exam Category B-F See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. B05.010.001 E "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Nozzle-to-Safe-End 86% Volume Coverage Butt Weld @ 00 (UT from nozzle I.D. in lieu of PT from O.D.)1-RPV-WR53 NC System Exam Category B-F See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. B05.010.001A "E" "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Nozzle-to-Safe-End 86% Volume Coverage Butt Weld @ 00 (UT from nozzle side)1-RPV-WR53 NC System Exam Category B-F See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. B05.010.001B "E" "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Nozzle-to-Safe-End 86% Volume Coverage Butt Weld @ 0° (UT from safe-end side) _I-RPV- NC System Exam Category B-F See Paragraph See Paragraph See Paragraph See Paragraph WR53A Reactor Vessel Item No. B05.010.002 "E" "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Nozzle-to-Safe-End 81% Volume Coverage Butt Weld @ 1800 (UT from nozzle I.D. in lieu of PT from O.D.) ._1-RPV- NC System Exam Category B-F See Paragraph See Paragraph See Paragraph See Paragraph WR53A Reactor Vessel Item No. B05.010.002A "E" "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Nozzle-to-Safe-End 81% Volume Coverage Butt Weld @ 1800 (UT from nozzle side)1-RPV- NC System Exam Category B-F See Paragraph See Paragraph See Paragraph See Paragraph WR53A Reactor Vessel Item No. B05.010.002B "E" "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Nozzle-to-Safe-End 81% Volume Coverage _Relief Request 02-004 Rev. 1 Pana'Aof 9_ J -?JV0 Relief Request 02-004 Rev. 1 Page 4 of 9,_____________

Butt Weld @ 180° (UT from safe-end side) __________

I. II. & III. IV. V. VI. VIl.Limited System / Code Requirement from Which Basis for Relief Alternate Justification Implementation Area/Weld Component for Which Relief is Requested:

Examinations or for Granting Schedule I.D. Relief is Requested:

100% Exam Volume Coverage Testing Relief Number Area or Weld to be Exam Category Examined Item No.Fig. No.Limitation Percentage 1-53A NC System Exam Category B-J See Paragraph See Paragraph See Paragraph See Paragraph 43L Reactor Vessel Item No. B09.011.090 "F' G ,I "K" Core Flood Fig. IWB-2500-8(c)

Safe-End to Pipe 76% Volume Coverage Circumferential Weld@00 1-53A NC System Exam Category B-J See Paragraph See Paragraph See Paragraph See Paragraph 43L Reactor Vessel Item No. B09.011.090A

'F' "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Safe-End to Pipe 76% Volume Coverage Circumferential Weld (UT from nozzle I.D. in lieu of_______ @ 00 PT from O.D.)1-53A-01-lL NC System Exam Category B-J See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. B09.01 1.100 'T' "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Safe-End to Pipe 83% Volume Coverage Circumferential Weld@ 1800 1-53A-01-IL NC System Exam Category B-J See Paragraph See Paragraph See Paragraph See Paragraph Reactor Vessel Item No. B09.01 1.1OOA "F' "G" "I" "K" Core Flood Fig. IWB-2500-8(c)

Safe-End to Pipe 83% Volume Coverage Circumferential Weld (UT from nozzle I.D. in lieu of@ 1800 PT from O.D.) _ _Items that are listed in the table above were inspected in April of 2002.Note: See Attachment A for a drawing on all the welds listed above.

Relief Request 02-004 Rev. 1 Page 5 of 9 IV. Basis for Relief (See Attachment A for area/weld locations.)

Paragraph A: During the ultrasonic examination of welds 1-RPV-WR34 and 1-RPV-WR35, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 36% and 42% respectively.

Limitations were caused by the core guide lugs & flow stabilizers for WR34 and incore nozzles & flow stabilizers for WR35 that restrict the scanning surface as shown on the Attachment A, B, and C drawings.

The percentage of coverage reported represents the aggregate coverage from all scans. Some areas received no coverage at all while some areas were completely covered from four directions.

13.3% of the near surface (inner 15 % of wall thickness) volume of the weld and base material was covered in four scan directions using a 700 beam angle. 76.6% of the near surface volume of the weld and base material was covered with a 70° beam angle from one axial and circumferential direction.

Only 10.1% of the near surface volume of the weld and base material received no coverage.

There were no recordable indications found in the areas that were examined for either of these 2 welds. In order to achieve more coverage the core guide lugs, incore nozzles and flow stabilizers would have to be moved to allow greater access for scanning, which is impractical.(See Attachment A for drawing on both welds)(See Attachment B for drawings on Weld 1-RPV-WR34)(See Attachment C for a drawing on Weld 1-RPV-WR35)

Paragraph B: During the ultrasonic examination of welds 1-RPV-WR13 and 1-RPV-WR13A, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 82%. Limitations were caused by the outlet nozzle boss that restricts the scanning surface both from the nozzle I.D. and the vessel I.D.. The percentage of coverage reported represents the aggregate coverage from all scans. The weld and adjacent base material received 100% coverage from the nozzle bore with 150 and 45° beam angles. Scans from the vessel shell side resulted in 42% coverage of the weld and base material with a 450 beam angle of the outer 85% of the vessel wall and coverage of the inner 15% with a 70° beam angle. There were no recordable indications found in the areas that were examined for item numbers B03.090.001 and B03.090.002.

There were recordable indications found during examination of item numbers B03.090.001A and B03.090.002A.

All of the indications were detected from the nozzle bore and were determined to be acceptable, sub-surface flaws. In order to achieve more coverage, the outlet nozzle boss would have to be moved to allow greater access for scanning, which is impractical.(See Attachment E for drawing on both welds)Paragraph C: During the ultrasonic examination of welds 1-RPV-WR54 and 1-RPV-WR54A, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 81% of the required volume.The Core Flood Nozzles of a B&W 177 plant have several obstructions which limit ultrasonic examination coverage.In order of significance these are:* The flow restrictor which is welded to the inner bore of the nozzle.* The Inlet nozzles located 30° on either side of each core flood nozzle.* The taper above the core flood nozzles associated with the Core Support Ledge.

Relief Request 02-004 Rev. 1 Page 6 of 9 The percentage of exam volume coverage reported represents the aggregate coverage as follows:* Weld and adjacent base material = 81% scanned parallel to the weld centerline in two directions and perpendicular to the weld centerline from one direction.

Inner 15% from the vessel ID = 97%, in four orthogonal directions.

There were no recordable indications found in the areas that were examined for either of these 2 welds. In order to achieve more coverage, the inlet nozzles would have to be moved and the taper on the flange would have to be redesigned to allow greater access for scanning, which is impractical.

In addition, because of the proximity of the flow restrictors no scanning was performed from the nozzle I.D. (0% examination coverage).

In order to achieve more coverage, the flow restrictor would have to be moved to allow access for scanning, which is impractical.(See Attachment D for a drawing on the core flood nozzle).Paragraph D: During the ultrasonic examination of inside radius sections 1-RPV-WR54 and 1-RPV-WR54A, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 52%. Limitations were caused by the flow restrictor that prevents scanning from the nozzle bore surface. The percentage of coverage reported represents the aggregate coverage from all scans. There were no recordable indications found in the areas that were examined for either of these inside radius sections.

In order to achieve more coverage, the flow restrictor would have to be moved to allow greater access for scanning, which is impractical.(See Attachment D for a drawing on the core flood nozzle)Paragraph E: During the ultrasonic examination of welds -RPV-WR53 and 1-RPV-WR53A, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 86% and 81%, respectively from two axial and two circumferential directions.

Limitations were caused by air at the top of the nozzle that prevented the transducer from making contact for scanning the surface. The reactor vessel inspection services vendor made two attempts to evacuate the air with equipment made for the purpose but additional air was reintroduced from an unknown source. After the second attempt was unsuccessful and the source for the air could not be determined, a decision was made to perform the scan and obtain as much coverage as possible (the percentages shown above). The vendor noted that similar problems with eliminating trapped air have been experienced on other reactor vessels with small diameter piping.The percentage of coverage reported represents the aggregate coverage from all scans. There were no recordable indications found in the volumes that were examined for either of these 2 welds. In order to achieve more coverage, the air would have to be eliminated which proved to be impractical during the subject inspection.

Alternatively, it is impractical to perform this exam from the outside nozzle surface due to the excessive personnel radiation exposure.

Approximately 40 man-hours would be required to prepare each core flood nozzle-to-safe end weld for examination from the outside surface. The preparation involves removing the refueling canal seal plate, shielding bricks, shielding supports in the nozzle area and insulation.

The radiation levels in this area are expected to be 0.51 Rlhr. An alternative path would be to enter from the bottom of the reactor vessel and build scaffolding approximately 30 feet high to reach the core flood nozzles. This activity would require approximately 80 man-hours.

40 man-hours in a 0.51/hr radiation field and 40 man-hours in a 1-2 R/hr radiation field. Total estimated exposure would be 80-140 man-rem. Shielding in this area is impractical.

Any remote inspection would require the same preparatory work.

Relief Request 02-004 Rev. 1 Page 7 of 9 Paragraph F: During the ultrasonic examination of welds 1-53A-02-43L and 1-53A-01-lL, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 76% and 83%, respectively from two axial and two circumferential directions.

Limitations were caused by air at the top of nozzle that prevented the transducer from making contact for scanning the surface. The reactor vessel inspection services vendor made two attempts to evacuate the air with equipment made for the purpose but additional air was reintroduced from an unknown source. After the second attempt was unsuccessful and the source for the air could not be determined, a decision was made to perform the scan and obtain as much coverage as possible (the percentages shown above). The vendor noted that similar problems with eliminating trapped air have been experienced on other reactor vessels with small diameter piping.The percentage of coverage reported represents the aggregate coverage.

There were no recordable indications found in the volumes that were examined for either of these 2 welds. In order to achieve more coverage, the air would have to be eliminated which proved to be impractical during the subject inspection.

V. Alternate Examinations or Testing Paragraph G: The scheduled 10-year code examination was performed on the referenced area/weld and it resulted in the noted limited coverage of the required ultrasonic volume. No additional examinations are planned for the area/weld during the current inspection interval.VI. Justification for Granting Relief Paragraph H: Ultrasonic examination of welds for item numbers B01.01 1 and B01.021 were conducted using personnel, equipment and procedures qualified in accordance with ASME Section XI, Appendix VIII, Supplements 4 and 6, 1995 Edition with the 1996 Addenda as administered through the Performance Demonstration Initiative (PDI)Program. Although 100% coverage of the examination volume could not be achieved, the amount of coverage obtained for these examinations along with the additional volumetric and visual examinations (listed in subsequent paragraph) provides an acceptable level of quality and integrity. (See Paragraph J for additional justification.)

In addition to the Category B-A welds that relief is being sought for, there were 5 circumferential and 6 longitudinal, Category B-A welds that were inspected and all obtained greater than 90 % coverage and there were no reportable indications found during the inspections.

Visual examinations were also performed as part of the reactor vessel inspections (item number B 13.010.001 and B 13.050.001) and were found to be without any reportable indications.

Paragraph I: Ultrasonic examination of areas/welds for item numbers B03.090, B03.100, B05.010 and B09.011 were conducted using personnel, equipment and procedures qualified in accordance with ASME Section XI, Appendix I, 1989 Edition with no Addenda Inspection of the B05.010 and B09.011 welds from the outside diameter is not a viable alternate due to the dose that would be received to prepare and perform the inspections.

Relief Request ONS-001 and ONS-002 were written to perform UT from the ID surface in lieu of a surface exam from the OD surface of all reactor vessel nozzles to pipe welds due to the radiation exposure that is involved with performing inspections from the OD surface. Relief was granted for ONS-001 and ONS-002 on an SER dated 11-15-95.

Although 100% coverage of the examination volume could not be achieved, the amount of coverage obtained for these examinations provides an acceptable level of quality and integrity. (See Paragraph J for additional justification.)

Paragraph J: Duke Energy will use pressure testing and VT-2 visual examination to compliment the limited examination coverage.The Code requires (reference Table IWB-2500-1, item numbers B 15.010 and B 15.050) that a system leakage test be performed after each refueling outage for Class 1. Additionally a system hydrostatic test (reference Table IWB-Relief Request 02-004 Rev. 1 Page 8 of 9 2500-1, item numbers B 15.011 and B15.051) is required once during each 10-year inspection interval.

These tests require a VT-2 visual examination for evidence of leakage. This testing provides adequate assurance of pressure boundary integrity.

Duke Energy will use VT-3 visual examination to compliment the limited examination coverage.

The Code requires (reference Table IWB-2500-1, item number B 13.010) that a VT-3 examination be performed after the first refueling outage and subsequent refueling outages at approximately 3 year periods. During the first and second periods of an interval a VT-3 examination is performed on areas above and below the reactor core that are made accessible for examination by removal of components during normal refueling outages. During the third period of an interval the VT-3 examination is performed on all of the reactor vessel interior surfaces at the same time that the automated UT exams are performed on the reactor vessel welds. This examination provides adequate assurance of pressure boundary integrity.

In addition to the above Code required examinations (volumetric, pressure test, and VT-3), there are other activities which provide a high level of confidence that, in the unlikely case that leakage did occur through these welds, it would be detected and isolated.

Specifically, leakage from these welds would be detected by monitoring of the Reactor Coolant System (RCS), which is performed once each shift under procedure PT/1,2,3/A/0600/10, "RCS Leakage".

This RCS leakage monitoring is a requirement of Technical Specification 3.4.13, "Reactor Coolant System Leakage".

Leakage is also evaluated in accordance with this Technical Specification.

The leakage could also be detected through several other methods. One is the RCS mass balance calculation.

A second is the Reactor Building air particulate monitor. This monitor is sensitive to low leak rates; the iodine monitor, gaseous monitor and area monitor are capable of detecting any fission products in the coolant and will be activated by coolant leakage. A third is the level indicator in the Reactor Building normal sump. A fourth is a loss of level in the Letdown Storage Tank.Duke Energy has examined the welds/components referenced in this request to the maximum extent possible utilizing the latest in examination techniques and equipment.

These welds were rigorously inspected by volumetric NDE methods during construction and verified to be free from unacceptable fabrication defects. Based on the portions and results of the required volumetric and visual examinations performed during this outage, it's our opinion that this combination of examinations provides a reasonable assurance of component integrity.

VII.TmDlementation Schedule Paragraph K The scheduled third 10-year interval plan code examination was performed on the referenced area/weld resulting in limited volumetric coverage.

No additional examinations are planned for the area/weld during the current inspection interval.

The same area/weld may be examined again as part of the next (fourth) 10-year interval plan, depending on the applicable code year edition and addenda requirements adopted in the future.

Relief Request 02-004 Rev. 1 Page 9 of 9 VIII. Other Information The following individuals contributed to the development of this relief request: James J. McArdle (Principal NDE Level III Inspector) provided Sections II through V and part of Section VI.B. W. Camey, Jr. (Oconee Engineering) provided part of Section VI.Larry C. Keith (Oconee ISI Plan Manager) compiled the remaining sections.Sponsored By: Approved By:<&j7g.o /W Date:4 Al K +C, fj~e Date 514 1 C3 Attachment A Attachment B Attachment C Attachment D Attachment E Drawing on Reactor Vessel Welds Drawings on Weld I -RPV-WR34 Drawings on Weld 1-RPV-WR35 Drawing on Weld 1 -RPV-WR54 and I -RPV-WR54A (core flood nozzle)Drawing on Weld -RPV-WR13 and 1-RPV-WR13A S// e)-

'3 I 11 10 I"It Attachment A 0 NORTH o Ly IDEEP END OF L NOfZLE f6(09 --) l t l12 --Il Il to I GUIDE GUIDE LUG LUGa 27 ~ ~ ~ ~ ~ ~ 0 3/ \W09 OCONEE-1 1-RPV-WR34 m B01.011.005

.-_ _ % it~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~4 WELD (NEAR SURFACE): 4.12 SQ IN. (70-L)WELD (BALANCE OF VOLUME): 3.03 SQ IN. (45-L) 6.42 SQ IN. (45-S)BASE METAL (NEAR SURFACE): 7.31 SQ IN. (70-L)BASE METAL (BALANCE OF VOLUME): 22.67 SQ IN. (45-L) 32.19 SQ IN.(45-S)CORE GUIDE LUG QUAN: 12 45 0 L 45 0 S 70°L THIS VIEW DEPICTS ALPHA (AXIAL) SCANS FIRING DOWNWARD (DIRECTILN 11)FLOW STABILIZER REMNANT QUAN: 12 W09 OCONEE-1 1-RPV-WR34 B01.011.005 PARTIAL SCANS LUGS AND FLOW REMNANTS DUE TO GUIDE STABILIZER j Attachment B Page ;- of lAttachment B! Page of L0 WELD (NEAR SURFACE)0.00 SQ IN.WELD (BALANCE OF VOLUME): 0.00 SQ IN.BASE METAL (NEAR SURFACE): 0.00 SQ IN.BASE METAL (BALANCE OF VOLUME): 0.00 SQ IN.CORE GUIDE LUG QUAN: 12 70°L 45°L THIS VIEW DEPICTS ALPHA (AXIAL) SCANS FIRING UPWARD (DIRECTION 12)FLOW STABILIZER REMNANT QUAN: 12 W09 OCONEE-1 1-RPV-WR34 B01.011. 005 PARTIAL SCANS LUGS AND FLOW REMNANTS DUE TO GUIDE STABILIZER l Attachment B; Page of 1 1 L WELD (NEAR SURFACE): 4.12 SQ IN. (70-L)WELD (BALANCE OF VOLUME): 7.17 SQ IN. (45L & 45'S)BASE METAL (NEAR SURFACE): 5.62 SQ IN. (70-L)BASE METAL (BALANCE OF VOLUME): 18.25 SQ IN. (45-L) 26.88 SQ IN.(45-S)CORE GUIDE LUG QUAN: 12 THIS VIEW DEPICTS THETA (CIRC) SCANS (DIRECTION 3 & 4)FLOW STABILIZER REMNANT QUAN 12 W09 OCONEE-1 1-RPV-WR34 B01.011.005 PARTIAL SCANS LUGS AND FLOW REMNANTS DUE TO GUIDE STABILIZER

._

Pt ;p.:0 n 0 14 n E m 0 =" n CHAKE.a I R29.17 STAR, LEDGE TAPER Z-27.00'0 NWN SCAN LIMITS 1. 'y NOTE: CAD FILE .5 SCALE INLET R29.17-T NWP SCAN LIMITS NOTE: CAD FILE .5 SCALE 7s.25bo N/1"CLD CE'ERLWC 75 R12,11 SCAN INDEX 0.50' FOR 12 R2 IINOZZLE-TO-SHELL SCANS 15X TS N8R/NI3L SCAN LIMITS OCONEE-1 MT / NOTE: CAD FILE .5 SCALE W1_lRPV-WR54 B03.090.007 B03.090.007A IWAII AD 03.100.007 ORCOAT.O.

B RErEKI-CE W19 cm Is 11 1 RPV-WR54A ps.75 803.090.008 803.111 IIA T4-R4 T9_R9 PARE TO-RS.12 2x3 UT HEAD CONFIGURATION

3 OCONEE-1 Z._-: ruil%FOR APPENDIX VIII SHELL SCANS 10 YEAR RV ISI CORE FLOOD (SHELL)AS VIEWED rROM VBLOCK ATTACHMENT SIVC URSULA EXA ]NATION SHEET 3 OF 14

Relief Request 02-005 Rev. 1 Page 1 of 10 -Proposed Relief in Accordance with 10 CFR 50.55a(g)(5)(iii)

Inservice Inspection Impracticality Duke Energy Corporation Oconee Nuclear Station- Unit 1 (EOC-20)Third 10-Year Interval -Inservice Inspection Plan Interval Start Date= 7-15-1994 Interval End Date=1-1-2004 ASME Section XI Code -1989 Edition with No Addenda I. 11. & III. IV. V. VI. VII.Limited System / Code Requirement from Which Basis for Alternate Justification for Implementation Area/Weld Component for Relief is Requested:

Relief Examinations Granting Relief Schedule I.D. Which Relief is 100% Exam Volume Coverage &/or or Testing Number Requested:

4 Scan Directions Area or Weld o be Exam Category Examined Item No.Fig. No.Limitation Percentage 1-SGA-WG25 RC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph Steam Generator A Item No. B03.130.005 "A" " ..pT" Nozzle-to-Vessel Fig. IWB-2500-7(a)

Weld 57.98% Volume Coverage _ _ _ _ _ _1-SGB-WG25 RC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph Steam Generator B Item No. B03.130.006 "A" "0" .p" Nozzle-to-Vessel Fig. IWB-2500-7(a)

Weld 57.98% Volume Coverage 1-SGA-WG25 RC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph Steam Generator A Item No. B03.140.005 "A" " " .Q, "T Noizle Inside Radius Fig. IWB-2500-7) (a)Section 70.21% Volume Coverage _1-SGB-WG25 RC System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph Steam Generator B Item No. B03.140.006 "A" "" "Q" .T" Nozzle Inside Radius Fig. IWB-2500-7(a)

Section 70.21% Volume Coverage ____1-LDCB-IN-HPI System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph VI Let Down Cooler B Item No. B03.150.003 "B" "0" "Q" "T, Inlet Nozzle-to-Fig. IWB-2500-7(a)

Channel Body Weld 27.48% Volume Coverage Relief Request 02-005 Rev. 1___________

__________

_ Page 2 of .o I. II. & III. IV. V. VI. VII.Liniited System I Code Requirement from Which Basis for Alternate Justification for Implementation Area/Weld Component for Relief is Requested:

Relief Exaninations Granting Relief Schedule I.D. Which Relief is 100% Exam Volume Coverage &/or or Testing Number Requested:

4 Scan Directions Area or Weld to be Exam Category Examined Item No.Fig. No.Limitation Percentage 1-LDCB-OUT-HPI System Exam Category B-D See Paragraph See Paragraph See Paragraph See Paragraph V2 Let Down Cooler B Item No. B03.150.004 "B" "0" Q ",, Outlet Nozzle-to-Fig. IWB-2500-7(a)

Channel Body Weld 27.48% Volume Coverage I-RPV- RC System Exam Category B-G- 1 See Paragraph See Paragraph See Paragraph See Paragraph LIGAMENTS Reactor Vessel Item No. B06.040.001A "C" "0" "T" Threads in Flange Fig. IWB-2500-12 (a-b-c-d)1800 to 3600 84.52% Volume Coverage ILP-128-80 LP System Exam Category C-F-I See Paragraph See Paragraph See Paragraph See Paragraph Reducer to Item No. C05.011.007 "D" "0" "5" Valve LP-18 Weld Fig. IWC-2500-7(a)

___________

59.74% Volume Coverage 1HP-192-15 HPI System Exam Category C-F-1 See Paragraph See Paragraph See Paragraph See Paragraph Pipe to Flange Item No. C05.021.006 "E" "0" "5" Orifice Weld Fig. IWC-2500-7(a)

_____________

60.99% Volume Coverage 1-51A-01-91A HPI System Exam Category C-F-1 See Paragraph See Paragraph See Paragraph See Paragraph Pipe to Item No. C05.021.043 "F' "0" "5" Valve HP-128 Weld Fig. IWC-2500-7(a)

________________

60.84% Volume Coverage 1HP-324-118B BPI System Exam Category C-F-I See Paragraph See Paragraph See Paragraph See Paragraph Tee to Item No. C05.021.065 "G" "O" "5" 'T" Valve HP- 119 Weld Fig. IWC-2500-7(a) 61.54% Volume Coverage _1-51A HPI System Exam Category C-F-1 See Paragraph See Paragraph See Paragraph See Paragraph 32AA Pipe to Item No. C05.021.078 "H" "0" "5" Valve IHP-23 Weld Fig. IWC-2500-7(a) 60.39% Volume Coverage iHP-393-127A HPI System Exam Category C-F-I See Paragraph See Paragraph See Paragraph See Paragraph Pipe to Item No. C05.021.084 "I" "0" "5" Valve 1lHP-105 Weld Fig. IWC-2500-7(a)

__________________

59.31 % Volume Coverage ___

Relief Request 02-005 Rev. 1 Page 3 of 10 -I. II. & III. IV. V. VI. VII.Limited System / Code Requirement from Which Basis for Alternate Justification for Implementation Area/Weld Component for Relief is Requested:

Relief Examinations Granting Relief Schedule I.D. Which Relief is 100% Exam Volume Coverage &/or or Testing Number Requested:

4 Scan Directions Area or Weld to be Exam Category Examined Item No.Fig. No.___________________

Limitation Percentage 1-51A-02-34B HPI System Exam Category C-F-I See Paragraph See Paragraph See Paragraph See Paragraph Elbow to Item No. C05.021.090

,"O" "S" "T" Valve lHP-134 Weld Fig. IWC-2500-7(a)

_________________

61.30% Volume Coverage IHP-193-12 HPI System Exam Category C-F-I See Paragraph See Paragraph See Paragraph See Paragraph Tee to Item No. C05.021.096 "K" "0" "S" Valve HP-26 Weld Fig. IWC-2500-7(a) 59.37% Volume Coverage IHP-70-11 HPI System Exam Category C-F-I See Paragraph See Paragraph See Paragraph See Paragraph Expansion Joint Item No. C05.021.102 "I," "" "5" M-0891 to Elbow Fig. IWC-2500-7(a)

Weld 56.22% Volume Coverage 1-5lA HPI System Exam Category C-F-1 See Paragraph See Paragraph See Paragraph See Paragraph 103A Pipe to Item No. C05.021.110 "M" "0" "5" "T" Valve 1HP-109 Weld Fig. IWC-2500-7(a) 60.71% Volume Coverage Note: See Attachment A for a drawing on the Steam Generator welds listed above.See Attachment B for a drawing on the Let Down Cooler welds listed above.See Attachment C for examination data for all items listed above.See Attachment D for a drawing on 1-RPV-LIGAMENTS (Item B06.040.001A).

Relief Request 02-005 Rev. 1 Page 4 of 10 IV. Basis for Relief Paragraph A: (The steam generator head material is SA 302, Gr. B and the nozzle material is SA 508, Cl. 1. The diameter of the Nozzle to Vessel weld is 48 inches and it has a wall thickness of 8 inches. These steam generators are scheduled to be replaced in the fall of 2003.)Welds: During the ultrasonic examination of welds 1-SGA-WG25

& 1-SGB-WG25, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 57.98%. The examination was performed in accordance with the requirements of ASME Section V, Article 4 as amended by ASME Section XI, Appendix I. Single sided access caused by the weld design prevents scanning the welds from four directions.

Scanning was performed from three directions, parallel and perpendicular to the welds from the vessel head side using 45°and 600 shear wave beams and straight beam search units. Scanning was limited from the nozzle side due to the tapered geometry.

The percentage of coverage reported represents the aggregate coverage obtained by all scans over the full length of the weld. The 450 and 600 scans parallel to the welds covered 50% of the weld metal and 100% of the base material on the head side from one direction.

The 45° and 600 scans perpendicular to the weld covered 37% of the base material on the nozzle side of the weld from one direction, 100% of the base material on the vessel head side of the weld from one direction and 97% of the weld metal from one direction.

In order to achieve more coverage the nozzle would have to be re-designed to allow scanning from both sides of the weld, which is impractical.

There were no recordable indications found during the inspection of these welds.Inner Radii: During the ultrasonic examination of the inside radius sections associated with both nozzle to vessel welds, 1-SGA-WG25

& 1-SGB-WG25, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 70.21%. The nozzle inner radii were examined from the vessel shell in two opposing directions using 600 and 70° shear wave beam angles. The search units were skewed from the nozzle centerline in order to provide a 450 intercept angle between the sound beam and any flaws oriented in the axial/radial plane within the required examination volume. The examination was performed in accordance with the requirements of ASME Section V, Article 4 as amended by ASME Section XI, Appendix I. There were no recordable indications found during the inspection of these inner radii.Paragraph B: (Material type for both welds is SA182, F316L. The diameter of the inlet nozzle to channel body weld and the outlet nozzle to channel body weld is 3 inches and they have a wall thickness of .875 inches.)During the ultrasonic examination of welds -LDCB-IN-Vl and 1-LDCB-OUT-V2, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 27.48%. Although these welds are classified as Category B-D the actual configuration is similar to a pipe branch connection.

The percentage of coverage reported represents the'aggregate coverage from all scans performed on the weld and base material.

The examination was performed from both the vessel shell side and the nozzle side of the weld. The 450 and 600 beam angles directed perpendicular to the weld covered 88.24% of the base material examination volume. The axial scans with 45° beams covered 37.46% of the examination volume including the weld and base material in two opposite directions.

In order to achieve more coverage, the nozzle would have to be re-designed to allow additional scanning from both sides of the weld, and across the width of the weld, which is impractical.

There were no recordable indications found during the inspection of these welds.In order to examine similar metal stainless steel welds refracted longitudinal wave and refracted shear wave search units are used. The refracted longitudinal wave search units have an inherent limitation in that the useful portion of the sound beam lies in the first beam path leg between the transducer and the inside surface of the component.

Beam paths beyond the inside surface of the component cannot be used to extend the examination coverage through the weld because of mode conversion that occurs at the inside surface. However, refracted longitudinal wave search units have better penetration through stainless steel weld metal than shear wave search units. When calibrating in accordance with ASME Section XI, Appendix III and using refracted longitudinal wave there is not enough sound Relief Request 02-005 Rev. 1 Page 5 of 10 energy available to establish a distance-amplitude-correction curve beyond the inside surface notch located in the basic calibration block.Paragraph C: During the ultrasonic examination of 1-RPV-LIGAMENTS, 100% coverage of the required examination volume could not be obtained.

The examination coverage was limited to 84.52%. Limitations are caused by the clad area at each stud hole that causes the search unit to lift off the scanning surface. There were no recordable indications found during the examination for this item. In order to achieve more coverage the cladding would have to be removed to allow for scanning, which is impractical.

Paragraph D: (This weld is 12 inches in diameter with a wall thickness of 1.168 inches and made of stainless steel.)During the ultrasonic examination of reducer-to-valve weld LP-128-80, coverage of the required examination volume was limited to 59.74%. The percentage of coverage reported represents the aggregate coverage from all scans performed on the weld and base material.

Single sided access, caused by the proximity of the valve taper, prevents access to both sides of the weld. In order to achieve coverage from four directions, the weld would have to be re-designed to allow scanning from both sides of the weld, which is impractical.

There were no recordable indications found during the inspection of this weld.See Paragraph N for additional basis for relief. (Note: When "near side" is referenced in Paragraph N for weld ILP-128-80, it is referring to reducer side.)Paragraph E: (This weld is 4 inches in diameter with a wall thickness of .531 inches and made of stainless steel.)During the ultrasonic examination of pipe-to-flange orifice weld 1HP-192-15, the examination coverage was limited to 60.99%. The percentage of coverage reported represents the aggregate coverage from all scans performed on the weld and base material.

Single sided access, caused by the proximity of the flange, prevents access to both sides of the weld. In order to achieve coverage from four directions, the weld would have to be re-designed to allow scanning from both sides of the weld, which is impractical.

There was one recordable indication found during the inspection of this weld. It was determined to be a geometric reflector due to weld root geometry.See Paragraph N for additional basis for relief. (Note: When "near side" is referenced in Paragraph N for weld IHP-192-15, it is referring to pipe side.)Paragraph F: (This weld is 4 inches in diameter with a wall thickness of .531 inches and made of stainless steel.)During the ultrasonic examination of pipe-to-valve weld 1-51A-01-91A, the examination coverage was limited to 60.84%. The percentage of coverage reported represents the aggregate coverage from all scans performed on the weld and base material.

Single sided access, caused by the proximity of the valve taper, prevents access to both sides of the weld. In order to achieve coverage from four directions, the weld would have to be re-designed to allow scanning from both sides of the weld, which is impractical.

There were no recordable indications found during the inspection of this weld.See Paragraph N for additional basis for relief. (Note: When "near side" is referenced in Paragraph N for weld 1-51A-01-91A, it is referring to pipe side.)Paragraph G: (This weld is 2.5 inches in diameter with a wall thickness of .375 inches and made of stainless steel.)During the ultrasonic examination of tee-to-valve weld 1HP-324-118B, the examination coverage was limited to 61.54%. The percentage of coverage reported represents the aggregate coverage from all scans performed on the weld and base material.

Single sided access, caused by the proximity of the valve taper, prevents access to both sides of the weld. In order to achieve coverage from four directions, the weld would have to be re-designed to allow Relief Request 02-005 Rev. 1 Page 6 of 10 scanning from both sides of the weld, which is impractical.

There were no recordable indications found during the inspection of this weld.See Paragraph N for additional basis for relief. (Note: When "near side" is referenced in Paragraph N for weld lHP-324-118B, it is referring to tee side.)Paragraph H: (This weld is 4 inches in diameter with a wall thickness of .237 inches and made of stainless steel.)During the ultrasonic examination of pipe-to-valve weld 1-51A-01-32AA, the examination coverage was limited to 60.39%. The percentage of coverage reported represents the aggregate coverage from all scans performed on the weld and base material.