ML022050114
| ML022050114 | |
| Person / Time | |
|---|---|
| Site: | North Anna  |
| Issue date: | 01/14/2002 |
| From: | Ernstes M Division of Reactor Safety II |
| To: | Christian D Virginia Electric & Power Co (VEPCO) |
| References | |
| 50-338/02-301, 50-339/02-301 | |
| Download: ML022050114 (126) | |
See also: IR 05000338/2002301
Text
Final Submittal
(Blue Paper)
1.
Reactor Operator Written Examination
2.
Senior Reactor Operator Written Exami
NORTH ANNA
EXAM 2002-301
50-338 AND 50-339
JUNE 6, 10-14, & 24-25, 2002
1. 001A 3.05 001/T2G 1/T2G 1/ROD CONTROL/C/A 3.5/3.5/M/NA02301/C/RA/LM
The rod control startup reset push-buttons are inadvertently depressed while unit 1 is
at 100% power.
Which one of the following describes the control room indication(s) and alarm(s) that
will change as a result of this action?
A. The rod banks A/B/C/D low/low-low limit alarm will annunciate and the step
counters will go to the full-out position.
B. The non-urgent failure alarm will annunciate and the step counters will go to the
full-out position.
C.' The rod banks A/B/C/D low/low-low limit alarm will annunciate and the step
counters will go to zero.
D. The non-urgent failure alarm will annunciate and the COMPUTER ALARM POWER
TILT ROD DEV/SEQ alarm will annunciate.
Time:
I
Points:
T2G I
ROD CONTROL
M
C
1.00
Version:
0 I 2 3 4 5 6 7 8 9
Answer: CDDAAAABAC
Scramble Range: A - D
SRO Tier:
T2GI
Cog. Level:
C/A 3.5/3.5
Exam:
NA02301
Misc:
RA/LM
2. 001AK 1.03 001/Ti G2/TIGI/ROD CONTROL/C/A 3.9/4.0/M/NA02301/C/RA/LSM/SC
The unit is at 90% power with the turbine in IMP-OUT.
The following conditions occur:
- Pressurizer level is increasing.
- Reactor power is increasing.
- Reactor Coolant System Tave/Tref deviation alarm is lit.
Which one of the following has occurred?
A' a continuous control rod withdrawal has occurred.
B. a main steam leak has occurred.
C. selected impulse pressure channel has failed low.
D. B loopTc has failed high.
Tuesday, July 23, 2002 01:31:23 PM
RO Tier:
Key Word:
Source:
Test:
1
A. Correct
B. Pressurizer level would not increase
C. Reactor power would lower
D. Would not effect pressurizer
Original question:
89
ID: 2892
Points: 1.00
The unit is at 90% power with the turbine in IMP-OUT. If a continuous control rod
withdrawal occurred, which one of the following items would NOT be a consequence?
A.
Pressurizer level increase
B.
Reactor power increasing
C.
Reactor Coolant System Tavg/Tref deviation
D.
Rod control urgent failure
Answer:
D
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ACCBABCACB
Scramble Range: A - D
RO Tier:
TIG2
SRO Tier:
TIGI
Key Word:
ROD CONTROL
Cog. Level:
C/A 3.9/4.0
Source:
M
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:23 PM
2
3. 001 G2.1.12 001//i 1G 1/TS BASIS/C/A 2.9/4.0/NEW/NA02301/S/RA/LSM/SC
The LCO for ITS 3.1.4, Rod Group Alignment Limits, reads as follows:
All shutdown and control rods shall be OPERABLE.
AND
Individual indicated rod positions shall be within 12 steps of their group step counter
demand position.
NOTE
When THERMAL POWER is less than or equal to 50% RTP, the indicated position of
each rod as determined by its individual rod position indicator may be within 24 steps
from its group step counter demand position for up to 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> per 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />. This NOTE
is not applicable for control rods known to be greater than 12 steps from the rod group
step counter demand position.
Which one of the following is the basis for this note?
A0 To allow stabilization of known thermal drift in the individual rod position indicator
channels.
B. To ensure that local power density increases due to a misaligned RCCA will not
cause the core design criteria to be exceeded.
C. This represents the time necessary for determining the actual unit SDM and, if
necessary, aligning and starting the necessary systems and components to initiate
boration.
D. To allow the determination of hot channel factors and to ensure that the shutdown
margin is within limits within one hour.
Tuesday, July 23, 2002 01:31:23 PM
3
Rod Group Alignment Limits
B 3.1.4
BASES
North Anna Units 1 and 2 B 3.1.4-5 Rev 0 (Draft 2), 09/18/00 LCO
The LCO has been modified by a Note. The Note permits a wider
tolerance on indicated rod position for a maximum of one hour
in every 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> to allow stabilization of known thermal
drift in the individual rod position indicator channels.
This thermal soak time is available both for a continuous one
hour period or several discrete intervals as long as the
total time does not exceed 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> in any 24 hour2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> period and
the indicated rod position does not exceed 24 steps from the
group step counter demand position. This allowance applies
to the indicated position of the rod, not its actual
position. If the actual position is known to be greater than
12 steps from the group step counter demand position, the
Conditions and Required Actions of the specification must be
followed.
Reduction of power to 75% RTP ensures that local LHR
increases due to a misaligned RCCA will not cause the core
design criteria to be exceeded.
Power operation may continue with one RCCA OPERABLE but misaligned, provided
that SDM is verified within 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br />. The Completion Time of 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> represents the time
necessary for determining the actual unit SDM and, if necessary, aligning and starting
the necessary systems and components to initiate boration. Since the core conditions
can change with time, periodic verification of SDM is required. A Frequency of 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br />
is sufficient to ensure this requirement
continues to be met.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ADACDCCBAA
Scramble Range: A - D
RO Tier:
SRO Tier:
TIGI
Key Word:
TS BASIS
Cog. Level: C/A 2.9/4.0
Source:
NEW
Exam:
NA02301
Test:
S
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:23 PM
4
4. 001 K2.05 001/T2G1//RPS MOTORS/M 4.2/4.2/NEW/NA02301/R/RA/LM/SC
The rod drive motor generator sets receive power from which one of the following?
Station service 480-volt busses:
A.A
B
BY' B
A
C. A
C
D.C
B
and C on unit 1
and C on unit 2
and C on unit 1
and C on unit 2
only on unit 1
only on unit 2
only on unit 1
only on unit 2
REF: Lesson Plan for Rod Control System (65) page 2
OBJ: 2.3.4a
Distractor
Distractor
Distractor
Tim4
RO Tier:
Key Word:
Source:
Test:
A - Incorrect Station service 480 volt bus B and C supply MG 2.1 .U-1
B - Correct
C - Incorrect MG 2.1 .U-1 is not supplied from Station service 480 volt bus A
D - Incorrect MG 2.2.U-2 is not supplied from Station service 480 volt bus B
I
Points:
1.00
Version:
0 1 23456789
Answer: BCACADAADB
Scramble Range: A - D
T2G1
SRO Tier:
RPS MOTORS
NEW
R
Cog. Level:
M 4.2/4.2
Exam:
NA02301
Misc:
RA/LM/SC
Tuesday, July 23, 2002 01:31:23 PM
.0 9/24/01
5
5. 002K6.02 001/T2G2/T2G2/RCP TRIP/M 3.6/3.8/BANK/NA02301/C/RA/GWL/SC
- Unit 2 is holding at 20% power for chemistry.
- "B" reactor coolant pump trips.
Which one of the following correctly describes how steam flow and water level in the
"B" steam generator will respond initially to the trip of the "B" RCP?
A. steam flow increases, level increases.
B. steam flow decreases, level increases.
C.' steam flow decreases, level decreases.
D. steam flow increases, level decreases.
Bank Question. North Anna Exam Bank. Question # 3780.
Lesson Plan Reactor Coolant System. #38 Objective 9.2
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CDCDAACCCA
Scra
RO Tier:
T2G2
SRO Tier:
T2G2
Key Word:
RCP TRIP
Cog. Level:
M 3.6/3.8
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/GWL/SC
amble Range: A - D
6. 003A4.02 00l/T2G I /T2GI/LOSP/C/A 4.3/4,5/NEW/NA02301/C/RA/LM/SC
1-RC-P-1B ("B" RCP) amps start fluctuating and the indicated vibrations begin
increasing rapidly. The backboards operator reports that "B" RCP proximity vibration
indication just pegged high, then the indication went to zero. The amps continue to
fluctuate. With respect to the RCP only, which one of the following actions should be
taken and why?
A. Trip the "B" RCP; the vibration monitoring indication was over-ranged and therefore
failed low.
B. Do not trip "B" RCP; the vibration instrument has failed and amp indication is known
to occasionally fluctuate.
C. RDo not trip the "B" RCP because the only failure was that the vibration monitoring
indication/sensor failed.
D. Trip the "B" RCP; vibrations have returned to normal but fluctuating amps are an
RCP trip criterion.
Tuesday, July 23, 2002 01:31:24 PM
6
REF: Reactor Trip or Safety Injection, EOP 1-E-0 Revision 27
OBJ: 12484
Distractor A - Incorrect - RCS hot leg temperatures stable or decreasing would support
or indicate Natural Circulation flow occurring.
B - Correct
Distractor C - Incorrect - RCS Tave increasing by itself is not clear support or indicate
Natural Circulation flow occurring
Distractor D - Incorrect - PZR level decreasing and RCS Tave increasing is not support
or indication of Natural Circulation flow occurring.
Question was modified on 06/04/02 to reflect the correct KA.
Time:
1
Points:
1.00
Version:
0 1 23456789
Answer: ADDBDBADDA
Scramble Range: A - D
RO Tier:
T2G I
SRO Tier:
T2G1
Key Word:
Cog. Level:
C/A 4.3/4.5
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LM/SC
003AK3.04 00l/TIG2/TI G1/ROD DROP/C/A 3.8/4.l/NEW/NA02301/C/RA/LSM/SC
Unit 1 is at 60% power when an oscillator in the rod control logic cabinet fails during
rod movement.
You receive a ROD CONTROL URGENT FAILURE alarm. Power to all of the
stationary and movable coils have dropped to zero. No other logic or electrical failures
have occurred. Which one of the following is your required action?
A0 Enter E-0, Reactor Trip or Safety Injection.
B. Enter AP-1.2, Dropped Rod.
C. Enter AP-1.1, Continuous Rod Motion.
D. Enter AP-1.3, Control Rod out of Alignment.
Tuesday, July 23, 2002 01:31:24 PM
7.
7
Enter E-0 because all rods will drop
MODULE NCRODP-65
4.
multiplexing error.
The regulation and phase failures feed a common detector card, referred to as
the failure detector card. A phase or regulation failure indicates that the CRDM coil(s)
may be overheating, a thyristor supplying power to a CRDM is faulty, or one of the
three phases to the power cabinet has been lost. A logic error card senses power to
the stationary and movable coils. If voltage to both coils is zero at the same time, the
urgent alarm actuates. This condition would result in a dropped control rod, since no
gripper coils are energized. A multiplexing error will actuate the alarm when a lift or
movable thyristor in the power cabinet(s) fails, causing a multiplexing error.
The logic cabinet failures which result in the ROD CONTROL URGENT
FAILURE alarm are as follows:
1.
oscillator failure,
2.
slave cycler failure, or
3.
printed card removed from normal position.
Failure of the oscillator in the logic cabinet can result in improper sequencing of
the CRDM coils, or a dropped control rod. Failure of the slave cycler indicates that
logic signals between the master cycler and the slave cycler are not being coordinated
properly.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ACCCADACAA
Scramble Range: A - D
RO Tier:
TIG2
SRO Tier:
TIGI
Key Word:
ROD DROP
Cog. Level:
C/A 3.8/4.1
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:24 PM
8
8. 003K3.02 001/T2G 1/T2G I/RCS FLOW TAP/C/A 3.9/4.2/NEW/NA02301/C/RA/LM/SC
The following plant conditions exist:
- All RCPs are running.
- Reactor power is 90% by power-range NIs.
- "C" reactor coolant loop flow transmitter high-pressure tap breaks.
Which one of the following describes the effect of this loss on the RPS (disregard any
effects on containment)?
Loss of the flow tap in RCS loop "C" will:
A. only effect the RCS control function and not affect RPS or continued plant
operation.
B. provide a higher than normal flow signal and not affect RPS or continued plant
operation.
C. have no effect on reactor power.
Df result in a reactor trip.
REF:
OBJ: Topic 8.14a Terminal Knowledge Objective 12003
Distractor A Incorrect - RCS loop flow has no control functions.
Distractor B Incorrect - Loss of the high side tap will indicated decreased flow and
result in a reactor trip.
Distractor C Incorrect - The reactor is above the P8 setpoint.
D Correct
Time:
I
Points:
1.00
Version:
0 1 234567 89
RO Tier:
T2G I
Answer: DADADAADBC
SRO Tier:
T2G 1
Scramble Range: A - D
Cog. Level:
C/A 3.9/4.2
RCS FLOW TAP
NEW
C
Tuesday, July 23, 2002 01:31:24 PM
Key Word:
Source:
Test:
Exam:
Misc:
NA02301
RA/LM/SC
9
9.004A1 .06 001/T2G1/T2G I/VCT LEVEL/C/A 3.0/3.2/BANK/NA02301/C/RA/LM/SC
Given the following plant conditions:
- Unit 1 is at 100% power, with CVCS aligned for normal operation.
- One letdown orifice is in service.
- VCT level is 32%.
- All controls are in automatic, 1-CH-LT-1 112, VCT level transmitter, fails high.
Which one of the following describes the final actual VCT level? (Assume no operator
action.)
A. Automatic VCT make-up capability is lost, and the VCT level decreases until
charging pump suction automatically shifts to the RWST.
B. Continuous VCT automatic makeup occurs causing the VCT to overfill and the VCT
relief valve lifts.
C." 1-CH-LCV-1 115A, VCT level control valve, will divert to the stripper, and VCT level
will cycle due to automatic makeup.
D. 1 -CH-LCV-1 115A, VCT level control valve, will receive an open demand, but will not
open until the setpoint on 1-CH-LCV-1 1 12C, VCT level controller is exceeded.
Normal VCT level will be maintained.
REF:Bank question 5546
OBJ: Chemical & Volume Control 237
Question Comment
Level will cycle between 20% and 40% because makeup flow
is greater than flow through LCV-1 15.
Distractor A Incorrect - Level will initially decrease as LCV-1 15 diverts. Level will
decrease until auto Makeup starts but will stop increasing when auto makeup stops.
Distractor B Incorrect - Level will not overfill because auto makeup will stop and with
LCV-1 15 open level will begin decreasing.
C Correct
Distractor D Incorrect - There is no 1-CH-LCV-1 12C interlock with 1-CH-LCV-1 15A.
KA modified on 06/05/02
Time:
1
Points:
1.00
Version:
0 1 23456789
Answer: CCCBADCCAC
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:24 PM
10
RO Tier:
T2G I
SRO Tier:
T2G I
Key Word:
VCT LEVEL
Cog. Level:
C/A 3.0/3.2
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/LM/SC
10. 004K5.01 00I/T2G1/T2G 1/VCT/C/A 2.7/3.3/NEW/NA02301/C/RA/LSM/SC
Which one of the following is the reason for maintaining a hydrogen cover gas in the
VCT during normal at power operation?
A. To assure N-16 concentrations are ALARA.
B. To maintain RCS pH within the TRM limits.
C. To maintain conductivity below .017 micro Mhos.
D.' To maintain oxygen concentration below the TRM upper limit.
REF: NCRODP-41-NA pages 13, 91-93; NAPS TRM B3.4.1 pages B3.4.1-1 - B3.4.1-3
OBJ: 343 (SOER-97-1)
Distractor A - Incorrect - the use of hydrogen is not dependent on ALARA
considerations of N-16 activiation.
Distractor B - Incorrect - this is the purpose for Lythium Hydroxide.
Distractor C - Incorrect - radioactive gases in the VCT are collected by Primary Vents
and Drains System from CVCS.
D - Correct - hydrogen is absorbed in the VCT water and helps scavenge
oxygen in the RCS. Maintaining oxygen concentration less than the TRM limits with
Tavg greater than or equal to 250 F provides adequate corrosion protection.
Time:
1
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: DBACDBDBDD
Scramble Range: A - D
RO Tier:
T2G 1
SRO Tier:
T2G 1
Key Word:
Cog. Level:
C/A 2.7/3.3
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:24 PM
11
11. 005AA2.03 001//Ti G I/MISALIGNED RODS/M 2.5/3.0/NEW/NA02301/S/RA/LSM
Unit 1 was increasing power in accordance with 1-PT-34.3 following the successful
performance of a valve freedom test.
- When rod withdrawal began, a fuse blew that prevented 4 control rods from moving.
- Annunciator A-D4, CMPTR ALARM PR TILT ROD DEV/SEQ, actuates.
Which one of the following describes the required action(s)?
A. Stop the power increase and request I&C to adjust the IRPI's.
B. Enter 1-E-0.
C./ Stop the power increase and enter 1-AP-1.3, Control Rod out of Alignment.
D. Stop the power increase, declare the computer inoperable and enter 1-AP-42.
1-AP-1.3 CONTROL ROD OUT OF ALIGNMENT provides instructions for recovering
from the following misaligned rod events:
Any Single Control Rod is out of alignment by any number of steps, or Any Single
Control Rod is out of alignment by any number of steps, or Any Single Control Rod is
out of alignment by any number of steps, or
Multiple Control Rods are out of alignment provided Misaligned Control Rods are all in
the same group
Multiple Control Rods are out of alignment provided All of the misaligned Control Rods
are at the same position
Multiple Control Rods are out of alignment provided All of the misaligned Control Rods
are less than 12 steps out of alignment.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CCADBCBBAC
Scramble Range:A-D
RO Tier:
SRO Tier:
TIGI
Key Word:
MISALIGNED RODS
Cog. Level:
M 2.5/3.0
Source:
NEW
Exam:
NA02301
Test:
S
Misc:
RA/LSM
Tuesday, July 23, 2002 01:31:24 PM
12
12.005AK 1.01 00l/TG
01//STUCK ROD/C/A 3.1/3.8/BANK!NA0230I/R/RA/GWL/SC
- A ramp to 100% is in progress on unit 1.
- At 95% power, annunciator A-H7, A.F.D. MONITOR, alarms.
- The RO determines that rod H-14 in control bank D appears to be stuck at 144 steps.
Which one of the following describes the effect this event will have on core flux
patterns?
There should be:
A. a minimal effect on A.F.D.
elevation.
B. a minimal effect on A.F.D.
at the same elevation.
C. a large variation on A.F.D.
at the same elevation.
D. a large variation on A.F.D.
elevation.
indicators and on power range detectors at the same
indicators but a large variation on power range detectors
indicators but a minimal effect on power range detectors
indicators and on power range detectors at the same
North Anna Bank Question # 3761 modified for a stuck rod.
Associated objective: 11025.
A. Incorrect, there will be a large effect on axial flux, and power range detectors.
B. Incorrect, same as A.
C. Incorrect, same as A.
D. Correct
effect on
Tim,
RO Tier:
Key Word:
Source:
Test:
a Stuck rod will cause a large effect on axial flux difference, and a large
power range detectors at the same elevation.
I
Points:
1.00
Version:
0 1 23456789
Answer: DDABACCADB
Scramble Range: A - D
TIGI
SRO Tier:
STUCK ROD
Cog. Level:
C/A 3.1/3.8
BANK
Exam:
NA02301
R
Misc:
RA/GWL/SC
Tuesday, July 23, 2002 01:31:24 PM
13
13. 005K3.07 00l/T2G3/T2G3/RHR/M 3.2*/3.6*/NEW/NA02301/C/RA/LSM/SC
Unit one has cooled to slightly less than 100°F in preparation for refueling operations.
The Reactor Purification (RP) system is aligned so that the RP pumps take a suction
on the reactor cavity and the RHR system downstream of the combined discharge line.
Only the "A" RHR pump is running. "A" RHR heat exchanger CC flow transducer
FT-132A has just failed low.
Which one of the following will occur?
MCR alarm annunciation and indication and:
A. containment isolation trip valve 1-CC-TV-1 03A will close.
B. the 1B RHR pump will auto start.
C. the 1A RHR pump suction will auto swap to the RWST.
D. no automatic actions.
This is for indication only, has no automatic features
Module 40
Refueling operations. The plant cooldown continues to less than 140°F in preparation
for refueling operations. During refueling the RHR System is maintained in service with
the number of pumps and heat exchangers in operation as required by the decay heat
load. During this period the RHR System can be used, in conjunction with the RP
System, to purify the reactor cavity coolant. The RP System is aligned so that the RP
pumps take a suction on the reactor cavity and the RHR System downstream of the
combined discharge line. The flow rate from the RHR System to the RP System is
controlled at 60 gpm, which does not affect the shutdown cooling ability of the RHR
System.
Component Cooling Components
The Component Cooling (CC) System (see Figure 40-2) supplies cooling water
to the RHR heat exchangers and pump seal coolers. The cooling water is supplied to
the RHR components from the same header that supplies the reactor coolant pumps.
The supply flow is controlled by normally open, manually operated isolation valves.
The cooling water flow rate to heat exchanger 1A, as an example, is monitored by flow
transducer FT-132A which provides MCR alarm annunciation and indication. The
component cooling water flows through the shell of the heat exchanger at a design rate
of 1.72 x 106 Ibm/hr and receives 30.5 x 106 Btu/hr of heat transferred from the RHR
coolant. The outlet piping of the heat exchanger is protected from overpressurization
Tuesday, July 23, 2002 01:31:25 PM
14
by relief valve RV-128A which relieves at 150 psig to the containment drain trench.
Flow through heat exchanger 1A is controlled by motor-operated valve
1-CC-MOV-100A, which is controlled from the vertical board in the MCR.
The piping from heat exchanger 1A penetrates the Auxiliary Building where flow can be
isolated by containment isolation trip valve 1-CC-TV-103A. The valve is operated from
the
safeguards panel train A but automatically shuts upon receipt of a containment isolation
signal. The outlet temperature is monitored by a temperature element (TE-149A) which
provides MCR indication before flow combines with the flow from the other heat
exchanger and returns to the component cooling pumps.
The supply line to each heat exchanger provides flow to another manifold which
provides component cooling water (or makeup) to the following components:
1.
PDTT cooler,
2.
neutron shield tank cooler,
3.
neutron shield tank and surge tank (makeup),
4.
excess letdown heat exchanger, and
5.
RHR pump seal coolers.
The component cooling water is provided to seal cooler 1A, as an example, at
10 gpm through normally open, manual isolation valves. The cooling water cools the
seal coolant to ensure adequate lubrication and cooling exists to maintain zero seal
leakage. The component cooling flow rate through the cooler is monitored by a flow
switch (FS-131A); the cooler outlet temperature is monitored by TE-150A.
Overpressure protection for the cooler component cooling piping is provided by relief
valve RV-131A which relieves to the drain trench at 150 psig. The combined seal
cooler flow, along with the other components listed above, is returned to the piping
downstream of 1-CC-MOV-100B. It is common to receive RCP low CC flow alarms
intermittently when additional CC is "cut in" to the RHR heat exchangers
(1-CC-MOV-100A and/or B throttled open).
Power Supplies
The power supplies for the major components in the RHR System are listed in
Table 40-5 as well as illustrated in Figures 40-3 through 40-6.
Tuesday, July 23, 2002 01:31:25 PM
15
Key Word:
Cog. Level:
M 3.2"/3.6"
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
006K4.13 00 I/T2G2/T2G2/SOLI D STATE PROT/C/A 3.8/4.1 /M/NA02301/C/RA/LSM/SC
Unit 1 was at 100% power when a large-break LOCA occurred.
Which one of the following describes the interlocks between the
phase A?
SI signal and resetting
A. SI is automatically reset when phase A is reset.
B. Phase A is automatically reset when SI is reset.
C.0 Phase A can be reset without resetting SI.
D. SI can only be reset after phase A has been reset.
question replaced with bank question. Orginal bank question was no longer valid due
to system modifications
Unit one was operating at 100% power. An SI has occurred.
Which one of the following describes what INDICATIONS would be observed if one SI
RESETswitch was operated [i.e. one train of SI was reset] instead of the SI INITIATE
switch?
Since only one train was reset, an automatic SI would be reinitiated after 60 seconds.
The reset is transparent and no indications are available to the operators except by
referral to the computer printout.
Several solid state protection system status lights will flash.
All the status and permissive windows will illuminate and the first-out indicator will
illuminate red.
BANK 1992
NCRODP-93-10-LP-2, Revision
Time:
I
Points:
1.00
RO Tier:
Key Word:
Source:
Test:
T2G2
SOLID STATE PROT
M
C
3, Objective D.; LER 91-009
Version:
0 1 234567 8 9
Answer: CBDCDDABBD
Scramble Range: A - D
SRO Tier:
T2G2
Cog. Level:
C/A 3.8/4.1
Exam:
NA02301
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:25 PM
14.
SRO Tier:
T2G3
RO Tier:
T2133
16
15. 007EA2.02 001/T 0G2//E-0/M_4.3/4.6/NEW/NA02301/R/RA/LSM/GH
The unit is at 100% power.
- PRZR level transmitter LT-1459 failed on a previous shift and was placed in TRIP.
- Vital bus 1-11 inverter fails causing a loss of vital bus 1-11.
Which one of the following statements is correct?
The reactor should:
A. have tripped, the crew should manually trip the reactor and enter 1-FR-S.I.
B.0 have tripped, the crew should enter ITS 3.0.3.
C. NOT have tripped, the crew should enter 1-AP-2.2.
D. NOT have tripped, the crew should place the second PRZR level channel in TRIP.
Replaced because question was similar to a common question
H.
Emergency Response Guideline Procedure Usage
1.
Resetting a Safety System
a.
If the system has not been reset once, then the RO shall reset the
system when directed by procedure with concurrence from the cognizant SRO whether
or not it has actuated. This action is not required if the procedure step includes the
words "if required".
b.
Once the system has been reset, it is not necessary to reposition the reset switches
every time a procedure directs a reset; simply verify that the applicable status lights
indicate the reset condition. If it does not, then another reset is performed
NCRODP-92-LP-1
Revision 8
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BCACBCBBCD
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:25 PM
17
RO Tier:
TIG2
SRO Tier:
Key Word:
E-0
Cog. Level:
M 4.3/4.6
Source:
NEW
Exam:
NA02301
Test:
R
Misc:
RA/LSM/GH
16. 007K5.02 001/T2G3/T2G3/PRT/C/A 3.1/3.4/M/NA02301/C/RA/LSM/SC
Which one of the following outlines the appropriate operator actions for drawing a
bubble in the pressurizer (PRZR) once saturation conditions have been reached?
Ensure RCS temperature is greater than 170TF, and :
A. Increase PRZR spray flow and place another CVCS letdown orifice into service.
B. Decrease PRZR spray flow and place excess letdown into service.
C.' Increase CVCS letdown flow and maintain charging flow constant.
D. Decrease CVCS charging flow and maintain letdown flow constant.
Modified SHNPP Exam bank Question B02-062.
Time:
1
Points:
1.00
Version:
0 1 23456789
Answer: CACBBBCCCC
Scramble Range: A - D
RO Tier:
T2G3
SRO Tier:
T2G3
Key Word:
Cog. Level:
C/A 3.1/3.4
Source:
M
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:25 PM
18
17.008AK 1.01 001/T I G2/T I G2/SAFETY VALVE/C/A 3.2/3.7/M/NA02301/C/RA/GWL/LSM/SC
- Unit 1 is stable at 100% power.
- A pressurizer safety valve opens and fails to reseat and the unit trips.
Which one of the following indications would the operator expect to see as a result of
this event?
A. Safety tailpipe temperature
decrease.
B. Safety tailpipe temperature
increase.
C. Safety tailpipe temperature
slowly decrease.
D. Safety tailpipe temperature
slowly increase.
would increase to greater than 600'F and then slowly
would increase to greater than 600'F and then slowly
would increase to between 200°F and 300'F and then
would increase to between 200°F and 300°F and then
Reference - steam tables provided.
Bank Question From Farley 2000 NRC exam.
North Anna Lesson Plan NCRODP-74-NA objectives A and G. and pages 23 and 24 of
the lesson plan.
A. Incorrect, This would be the correct temperature for pressure at 2240 psig. Since the
pressure
the steam is going to is 8 to 11 psig the temperature will be between
212-330 degrees per the
steam tables.
B. Incorrect, Same as above for temperature.
C. (Correct) Incorrect, After the safety has relieved to the PRT the pressure will start
increasing towards 100 psig. Per the steam tables, as the pressure rises towards 100
psig, the temperature will also rise until the rupture disc relieves, then the pressure will
drop and stablize out. (PRT remains intact) - This answer is now correct based on NA
comments.
D. (Incorrect) Correct, as the pressure rises towards 100 psig, the temperature will also
rise.
Time:
I
Points:
1.00
Version:
0 1 2345 6789
Answer: DBCABDAACC
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:25 PM
19
RO Tier:
T1G2
SRO Tier:
T1G2
Key Word:
SAFETY VALVE
Cog. Level:
C/A 3.2/3.7
Source:
M
Exam:
NA02301
Test:
C
Misc:
RA/GWL/LSM/SC
18. 008K3.03 0O1/T2G3//RCP/C/A 4.1/4.2/BANK/NA02301/R/RA/LSM
Assume the following plant conditions:
- Unit 1 is at 100% power.
- Unit 2 is in mode 6.
- The unit-1 and unit-2 component cooling water systems are split out.
- 1-CC-P-IA has just been tagged out for bearing replacement.
- A ground on 1J emergency bus causes supply breaker 15J1 1 to trip.
- 1J emergency diesel generator starts, but does not load.
Which one of the following statements is correct concerning subsequent operation of
the RCPs?
A. Component cooling water flow to the pump thermal barriers must be manually
isolated to prevent thermal barrier damage.
B. The RCPs may be run indefinitely provided seal injection flow is maintained, and
the seal leak-off valves remain open.
C.f The RCPs must be tripped or the motor windings will be damaged.
D. Component cooling water flow must be restored within 20 minutes or RCP seal
damage will occur.
Associated objective(s):
Bank ID: 5580
3656
List the following information associated with the component cooling water pumps.
Power supply to each pump
Interlocks associated with manually starting a pump
Interlocks associated with automatically starting a pump
Interlocks associated with automatically tripping a pump
Time:
1
Points:
1.00
Version:
0 1 23456789
Answer: CDDDABCBDA
Scramble Range:A-D
20
Tuesday, July 23, 2002 01:31:25 PM
RO Tier:
T2G3
Key Word:
Source:
BANK
Test:
SRO Tier:
Cog. Level:
C/A 4.1/4.2
Exam:
Misc:
R
NA02301
RA/LSM
19. 009EK3.11 001/TI G2/TIG2/RCP TRIP/M 4.4/4.5/NEW/NA02301 /C/RA/LSM/SC
The continuous action page for 1-E-1 provides the requirements for RCP trip criteria.
Under some conditions the RCPs are directed to be tripped. Which one of the
following is the basis for this trip criteria?
A' To minimize mass loss from a small-break LOCA.
B. To protect the RCP seals.
C. To minimize RCS heatup.
D. To establish natural circulation.
ERG exe volume generic issues page 58
the only purpose is to minimize break flow for a small break LOCA
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ACACCDABCB
Scramble Range: A - D
RO Tier:
T1G2
Key Word:
RCP TRIP
Source:
Test:
NEW
C
SRO Tier:
TIG2
Cog. Level:
M 4.4/4.5
Exam:
Misc:
NA02301
RA/LSM/SC
20. 010K2.01 001/T2G2/T2G2/UV/DV/M 3.0/.34/M/NA02301/C/RA/LSM/SC
Which one of the following will NOT be automatically powered by its emergency bus,
following a UV/DV event? (Assume each component was running/energized prior to
the event.)
Af PRZR back-up heater.
B. Instrument air compressor.
C. 480-volt emergency bus.
D. Inside recirc spray pump.
NCRODP-74-LP-1 OBJ. D
BANK 1996/01/29
21
Tuesday, July 23, 2002 01:31:25 PM
Time:
1
RO Tier:
Key Word:
Source:
Test:
Points:
1.00
Version:
Answer:
T2G2
UV/DV
M
C
0123456
ADCAACA
SRO Tier:
Cog. Level:
Exam:
Misc:
789
D B B
Scramble Range: A - D
T2G2
M 3.0/.34
NA02301
RA/LSM/SC
011 A2.01 001//TIGI/3. 1/3.6/C/A 4.2/4.7/M/NA02301/S/RA/LSM/SC
The plant is in mode 4, RCS pressure is 300 psig, and RCS temperature is 2500F. A
large-break LOCA occurs and none of the charging pumps can be started due to
various malfunctions.
Which one of the following methods is required per
regain adequate core cooling?
A. Manually actuate SI.
B. Establish RHR cooling.
C. Manually open accumulator isolation valves.
Df Establish low-head SI flow.
reference
Bank 1993/10/11
1-AP-1 7, Attachment 8, Rev. 3, page 3
1-AP-17, "Shutdown LOCA," to
KA modified on 06/04/02
Time:
I
Points:
RO Tier:
Key Word:
Source:
Test:
1.00
Version:
0
Answer: D
3.1/3.6
M
S
123456789
CBABCBDAD
SRO Tier:
TIGI
Cog. Level:
C/A 4.2/4
Exam:
NA02301
Misc:
RA/LSM
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:26 PM
21.
22
22. 0l IG2.1.12 001//T2G2/TS/C/A 2..9/4.0/NEW/NA02301/S/RA/LSM/SC
Unit 1 is 100% power with the following conditions:
- Normal letdown was isolated by the previous shift due to a leak.
- Excess letdown flow was maximized, but PRZR level is still increasing.
- At 0200, the power supply to group 4 PRZR heaters failed, and repairs are
estimated to require 18 hours2.083333e-4 days <br />0.005 hours <br />2.97619e-5 weeks <br />6.849e-6 months <br />.
- At 0400 PRZR level is 87% and continues to increase at 1.5% per hour.
Assume the reactor does not trip on PRZR high level, and that the group 4 heaters are
returned to service at the precise time estimated by electrical maintenance. Which one
of the following describes the actions required by ITS?
Unit 1 must be:
A. in mode 3 no later than 0800 and must be in Mode 4 no later than 1400.
B. in mode 3 no later than 0900 and must be in Mode 4 no later than 1500.
C.0 in mode 3 no later than 1400 and must be in Mode 4 no later than 2000.
D. in mode 3 no later than 2100 and repairs will be completed before a mode 4 entry is
required.
'JlIv 23 2002 01:31:26 PM
23
Ti Ic*d.nv
TuesdavI
I
93% is reached at 8:00 am + six hours is 2:00pm + 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> is 8:00pm
Reference:
Provide references.
North Anna Units 1 and 2 B 3.4.9-4 Rev 0 (Draft 3), 10/09/00
Pressurizer
B 3.4.9 BASES ACTIONS A.1, A.2, A.3 and A.4
If the pressurizer water level is not within the limit, action must be taken to bring the unit
to a MODE in which the LCO does not apply. To achieve this status, within 6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br /> the
unit must be brought to MODE 3, with all rods fully inserted and incapable of
withdrawal. Additionally, the unit must be brought to MODE 4 within 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br />. This
takes the unit out of the applicable MODES.
The allowed Completion Times are reasonable, based on operating experience, to
reach the required unit conditions from full power conditions in an orderly manner and
without challenging unit systems.
B.1
If one required group of pressurizer heaters is inoperable, restoration is required within
72 hours8.333333e-4 days <br />0.02 hours <br />1.190476e-4 weeks <br />2.7396e-5 months <br />. The Completion Time of 72 hours8.333333e-4 days <br />0.02 hours <br />1.190476e-4 weeks <br />2.7396e-5 months <br /> is reasonable considering the anticipation
that a demand caused by loss of offsite power would be unlikely in this period. Pressure
control may be maintained during this time using the remaining heaters.
C.1 and C.2
If one group of pressurizer heaters are inoperable and cannot be restored in the
allowed Completion Time of Required Action B.1, the unit must be brought to a MODE
in which the LCO does not apply. To achieve this status, the unit must be brought to
MODE 3 within 6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br /> and to MODE 4 within 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br />. The allowed Completion Times
are reasonable, based on operating experience, to reach the required unit conditions
from full power conditions in an orderly manner and without challenging unit systems.
Time:
1
Points:
1.00
Version:
0 1 23456789
Answer: CCDBABADAA
Scramble Range: A - D
RO Tier:
SRO Tier:
T2G2
Key Word:
TS
Cog. Level:
C/A 2.9/4.0
Source:
NEW
Exam:
NA02301
Test:
S
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:26 PM
24
23. 011 K6.01 OOI/T2G2//ES-0.4/C/A 2.7/3.1/NEW/NA02301/R/RA/LSM/SC
Unit 1 was at 100% power when a loss of off-site power occurred. The crew has
transitioned to 1-ES-0.4, Natural Circulation Cooldown with Steam Void in Vessel
(without RVLIS), from 1-ES-0.2A, Natural Circulation Cooldown with CRDM Fans.
The following conditions currently exist:
- RCS pressure is 1600 psig.
- RCS temperature is 450'F.
The crew has just completed step 6, which requires them to maintain
injection flow equal to letdown and seal leakoff flow.
charging and seal
Which one of the following is the reason for equalizing charging and letdown flows
during the subsequent depressurization?
A.f Allows PRZR level to be used for monitoring void growth.
B. Assures RCS total mass does not drop below minimum conditions assumed in
FSAR analysis.
C. PRZR level is not accurate during these conditions and flow matching assures the
PRZR will not go solid.
D. Assures the regenerative heat exchanger is not over stressed due to large
fluctuations in charging and letdown.
Reference
EOP Owners Group Guidelines
Time:
I
Points:
1.00
RO Tier:
Key Word:
Source:
Test:
T2G2
NEW
R
Version:
0 1 23456789
Answer: AAAADBABBB
Scramble Range: A - D
SRO Tier:
Cog. Level:
C/A 2.7/3.1
Exam:
NA02301
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:26 PM
F
25
24. 01 2K5.02 001/T2G2/T2G2/RPS/C/A 3.1/3.3/NEW/NA02301/C/RA/LSM
Which one of the following is the purpose of the overpower delta T trip?
The trip was designed to:
A. provide protection for a departure from nucleate boiling ONLY.
B3. act as backup to the high neutron flux trip and limit required range of
overtemperature delta T protection.
C. provide protection for departure from nucleate boiling and act as a backup to the
high neutron flux trip.
D. continuously calculate the RCS overpower delta T trip settings under varying load
conditions and transients.
Delta T protection system. The overtemperature delta T trip is designed to protect the
reactor core from departure from nucleate boiling (DNB) conditions by continuously
calculating the RCS overtemperature delta T trip settings under varying load conditions
and transients. The overpower delta T trip is designed to protect against a high fuel rod
power density and subsequent fuel rod cladding failure and fuel meltdown. The
overpower delta T reactor trip acts as a backup to the high neutron flux trip and limits
required range of OTDT protection.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BACCACBCAA
Scramble Range: A - D
RO Tier:
T2G2
SRO Tier:
T2G2
Key Word:
Cog. Level:
C/A 3.1/3.3
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM
"
ml*ul 92 2002 01:.3:.96 PM
26
T e
Y,
y I
25. 013A1.05 001/02G1/T2G1/ESF/C/A 3.4/3.6/BANK/NA02301/C/RA/LM
Given the following plant conditions:
- The unit is currently at 480°F
- Normal cooldown is in progress.
A steam break occurs on the 40-inch main steam manifold.
Which one of the following is the ESF response to this failure?
A. Neither a main steam line isolation nor safety injection will occur.
B. Only a safety injection will occur.
C.f Only a main steam line isolation will occur.
D. Both a main steam line isolation and a safety injection will occur.
REF: NA bank question 3824
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CCDDCAADAC
Scramble Range: A - D
RO Tier:
T2G I
SRO Tier:
T2G1
Key Word:
Cog. Level:
C/A 3.4/3.6
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/LM
Tuesday, July 23, 2002 01:31:26 PM
27
26. 013K6.01 00l/T2GI/T2G1/ESF/C/A 2.7/3.1/NEW/NA02301/C/RA/LSM/SC
Given the following plant conditions:
- A reactor shutdown is in progress as required by ITS 3.3.2.
- Pressurizer (PRZR) pressure PT-1455 failed low.
- The channel has been placed in trip.
- RCS pressure has decreased to 1750 psig during a plant cooldown.
- Lo-Lo PRZR pressure SI signals have been blocked as required by the
shutdown procedure.
- Subsequently, PRZR pressure PT-1456 fails high.
Which one of the following correctly describes how the ESF system will respond to this
failure?
A. Only a phase A actuation will occur.
Bf An SI and a phase A will occur.
C. No ESF actuation will occur, Io-lo PRZR pressure SI signals have been blocked.
D. No SI will occur, but the reactor will trip.
REF: Process Instrumentation & Control sheets NA-DW-108D014 sheet 5;
NA-DW-5655D 33 sheets 6 and 8; Lesson Plan for Safety Injection System (52);
Module NCRODP-52 Safety Injection System
OBJ: 1.2 page 45 of 56 LP
Distractor A - Incorrect - Pressurizer Pressure PT-455B in trip position and 456B failed
upscale provide will result in more than an SI actuation.
B - Correct - Pressurizer Pressure PT-455B in trip position and 456B failed
upscale provide will result in both an SI and Phase A isolation.
Distractor C - Incorrect - Lo-Lo Pressurizer Pressure SI signal auto unblocks.
Distractor D - Incorrect - SI does occur.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BBCDDCCBBD
Scramble Range: A - D
RO Tier:
T2GI
SRO Tier:
T2G1
Key Word:
Cog. Level:
C/A 2.7/3.1
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:26 PM
28
2-7. 014A2.04 001//T2G I/ROD CONTROL/M 3.4/3.9/BANK/NA02301/S/RA/LSM/SC
Assume the following plant conditions:
- Unit 1 is at 100% power
- The operator at the controls (OATC) informs the unit supervisor that the control
rods are automatically inserting for no apparent reason
- The OATC places the rod control bank selection switch to manual
- Rod motion stopped
- Control rods have stepped in 10 steps
- The OATC also notices that two control rods on "D" control bank did not insert
Which one of the following actions should the crew take in response to this event?
A.f Enter 1 -AP-1.3, "Control Rod Out of Alignment."
B. Trip the reactor and go to 1-E-0, "Reactor Trip or Safety Injection."
C. Commence an orderly shutdown in accordance with 1-OP-2.2, "Unit Power
Operation from Mode 1 to Mode 2."
D. Manually withdraw "D" control bank rods to the position of the rods that did not
move using 1-OP-58.2, "Rod Control System Operation."
bank 2157
Question was modified on 06/04/02 due to KA mismatch.
Time:
I
RO Tier:
Key Word:
Source:
Test:
Points:
1.00
Version:
Answer:
ROD CONTROL
BANK
S
0123456789
AACDACDBCC
SRO Tier:
T2C
Cog. Level:
M 3
Exam:
NA4
Misc:
RA/
Scr:
.4/3.9
02301
/LSM/SC
amble Range: A - D
Tuesday, July 23, 2002 01:31:26 PM
29
28. 014K4.06 001/42G2//ROD CONTROL/C/A 3.4/3.7/NEW/NA02301/R/RA/LSM/SC
While completing AP-1.3, attachment 2, Realigning Control Rod - Rod Low, the ROD
BANK LO/LO-LO LIMIT annunciator alarms. Which one of the following is the cause of
this alarm?
A. More than one rod in the same group has been moved simultaneously.
B. All of the affected bank's lift coils have been energized.
C. The local Manual/Automatic switch has been placed in MANUAL.
Dt The affected bank's pulse-to-analog convertor was pulsed to zero.
A. Does not alarm
B. May cause urgent failure alarm
C. Required action, but does not cause this alarm
D. Correct
Abnormal Procedure AP 1.3 Attachment 2
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: DDBDBDCDAD
RO Tier:
T2G2
Key Word:
ROD CONTROL
Source:
NEW
Scramble Range: A - D
SRO Tier:
Cog. Level:
C/A 3.4/3.7
Exam:
Misc:
R
NA02301
RA/LSM/SC
Tuesday, July 23, 2002 01:31:26 PM
Test:
30
29. 015/17AA2.08 001//TIGl/3.4/3.5/M 3.4/3.5/NEW/NA02301/S/RA/LSM/SC
Unit 1 is starting up after a refueling outage. At 25 % power the following RCP
temperatures exist:
"A" RCP
pump radial bearing 205'F
stator 295°F
motor bearing 190'F
"B" RCP:
pump radial bearing 210°F
stator 2850F
motor bearing 185°F
"C" RCP:
pump radial bearing 205'F
stator 285°F
motor bearing 205'F
Which one of the follow is the appropriate actions to direct the crew to perform?
A. There are no required actions at this power level.
B. Trip the reactor then secure A RCP.
C. Trip the reactor then secure B RCP.
Df Trip the reactor then secure C RCP.
C RCP motor Radial Bearing temperature
NEW SRO ONLY
Reference: BANK Question ID: 5435
is above temperature limit.
Which ONE of the following temperatures would require securing a reactor coolant
pump?
A.
RCP bearing 210°F
B.
RCP pump bearing 205°F
C.
D.
RCP motor bearing 205°F
Answer:
D
Tuesday, July 23, 2002 01:31:27 PM
31
Time:
1
Points:
1.00
Version:
0 1 23456789
Answer: DCBAABBACD
Scramble Range:A-fD
RO Tier:
SRO Tier:
TIGI
Key Word:
3.4/3.5
Cog. Level:
M 3.4/3.5
Source:
NEW
Exam:
NA02301
Test:
S
Misc:
RA/LSM/SC
30. 015/17AA2.10 001/TI GI//RCP/C/A 3.7/3.7/NEW/NA0230I/R/RA/GWL/SC
- Unit 1 is at 28% power.
- "C" RCP seal injection needle valve vibrates closed.
- A loss of semi-vital bus 1A causes the RCP thermal barrier CC return trip valves
1-CC-TV-116A, B, and C to go closed.
Which one of the following correctly describes the crew's required actions?
A. Trip the "C" RCP only and close its seal leakoff valve within five minutes.
B. Trip the reactor, then trip all RCPs.
C0 Trip the reactor, then trip "C" RCP onl.
D. Trip the reactor, then trip "C" RCP only and close its seal leakoff valve within five
minutes.
1-AP-33.2, Loss of all Seal Cooling.
Chemical and Volume Control Objective 9.10.
A. Incorrect, must trip the reactor first; also no need to close the seal leakoff valve.
B. Incorrect, no need to trip "A" or "B" RCP.
C. Correct, per 1-AP-33.2, all seal cooling is lost.
D. Incorrect, must trip the reactor first.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CDDDDABBCB
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
Key Word:
Cog. Level:
C/A 3.7/3.7
Source:
NEW
Exam:
NA02301
Test:
R
Misc:
RA/GWL/SC
Tuesday, July 23, 2002 01:31:27 PM
32
31. 01 5G2.1.32 001//T2G I/RCP/C/A 3.4/3.8/BANK/NA02301/S/RA/LSM
Given the following conditions:
-
Unit 1 is at 100% power.
-
C-G2, "RCP 1 B STANDPIPE HI LEVEL" has lit.
"- "B" seal injection flow is 7.8 GPM.
"- "B" seal leak-off flow is 0.2 GPM.
-
Seal return temperature is 150°F and rising steadily.
"- "B" RCP temperatures are as follows:
-
Motor stator - 2420F
-
Motor upper bearing - steady at 115 0F
-
Motor lower bearing - steady at 129 0F
-
Pump radial bearing - rising slowly at 129 0F
Based on the above indications, you should direct the operating crew to perform which
one of the following?
A' Trip the unit, secure "B" RCP and close its no. 1 seal leakoff valve after the pump
stops.
B. Trip the "B" RCP and close its no. 1 seal leakoff valve after the pump stops.
C. Close the "B" RCP's no. 1 seal leakoff valve within 5 minutes and shutdown the unit
within the next 30 minutes then secure the "B" RCP.
D. Trip the unit, secure "B" RCP and contact OMOC.
Reference required - 1-AP-33.1
BANK 1996 VISION OBJ. 11101
1996/01/29
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ADBBDCCCAC
Scramble Range: A - D
RO Tier:
SRO Tier:
T2G1
Key Word:
Cog. Level:
C/A 3.4/3.8
Source:
BANK
Exam:
NA02301
Test:
S
Misc:
RA/LSM
Tuesday, July 23, 2002 01:31:27 PM
33
015K3.06 00I/T2G1 //ROD CONTROL/C/A 2.9*/3.2*/BANK/NA02301/R/RA/LM
The unit is at 75% power with "D" bank control rods at 150 steps in AUTOMATIC when
power-range nuclear instrument N-44 fails LOW.
Assuming NO OPERATOR ACTION, which one of the following describes the effect
this failure will have on rod control?
The control rods will:
A. insert automatically for several seconds and then remain in that position.
B. insert automatically for several seconds and then withdraw to the previous position.
C. withdraw automatically for several seconds and then remain in that position.
D" withdraw automatically for several seconds and then insert to the previous position.
REF: NA Bank question 2162; Lesson Plan Rod Control (065)
OBJ: 2.9.2, 2.9.6
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7
Answer: DCDBCBAC
RO Tier:
T2G I
SRO Tier:
Key Word:
ROD CONTROL
Cog. Level:
Source:
BANK
Exam:
Test:
R
Misc:
89
D A
Scramble Range: A - D
C/A 2.9*/3.2*
NA02301
RA/LM
Tuesday, July 23, 2002 01:31:27 PM
32.
34
33. 01 5K6.02 001/T2G 1//SOURCE RANGE/C/A 2.6/2.9/BANK/NA02301/R/RA/LM/SC
Which one of the following describes how the pulse height discriminator failing low
would affect the indication of the failed source range channel?
A. The output would decrease due to failure in removing the higher amplitude
neutron-generated pulses.
B. The output would increase due to electronic filtering which narrows the pulse height
window.
C.0 The output would increase due to counting both the gamma- and
neutron-generated pulses.
D. The output would decrease due to decreased gamma interaction inside the
detector.
REF: Braidwood 9/14/98 RO; Ex-core Nuclear Instrumentation System (62) objective
3.2
Comment: The Pulse height discriminator is used to set window to detect those pulses
with an energy level high enough to be from an event associated with neutron
detection. Gamma and other interactions such as the alpha decay of fission product
daughters are of lower height (energy) and the discriminator normally electronically
removes them.
Time:
I
Points:
1.00
Version: 0 1 23456789
Answer: CCDADDCACC
Scramble Range: A - D
RO Tier:
T2G I
SRO Tier:
Key Word:
SOURCE RANGE
Cog. Level:
C/A 2.6/2.9
Source:
BANK
Exam:
NA02301
Test:
R
Misc:
RA/LM/SC
"sd
1w
Jul
Q*3
20100
1 '17 PM
35
Ti' a
Tue
Y.
y
I
34. 016A2.01 O01/T2G2/T2G2/NNIS/C/A 3.0/3. 1/NEW/NA02301/C/RA/LSM/SC
Which one of the following describes the immediate effects and the long-term effects if
the main generator hydrogen cooler air release valve level switch failed while the
Bearing Cooling System is operating normally in the tower mode? (For the long term
effect assume the problem is not corrected).
A.' There is no immediate effect. On the subsequent system startup, the bearing
cooling pump discharge MOVs will not open past the 25% system flow position.
B. There is no immediate effect. On the subsequent system startup, the bearing
cooling pump discharge MOVs must be opened manually.
C. Initially the bearing cooling pump discharge valves will not open past the 35%
system flow position. On the subsequent system startup, the pump discharge
MOVs must be opened manually.
D. Initially the bearing cooling pump discharge valves will not close past the 50%
system flow position. On the subsequent system startup, the pump discharge
MOVs must be de-energized to allow the valves to be open enough for the pump to
start. The valve then must be positioned manually.
NRCODP33
If the main generator hydrogen cooler Air Release Valve Level Switch failed while the
system is operating normally in the tower mode, there is no immediate effect. If the
problem is not corrected, on the subsequent system startup, the pump discharge MOVs
will not open past the 25 percent system flow position.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ADCABADDAC
Scramble Range: A - D
RO Tier:
T2G2
SRO Tier:
T2G2
Key Word:
NNIS
Cog. Level:
C/A 3.0/3.1
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tlules
,II.l
9¶-
9A1*9
23
1
2002
3
27 PM
36
I
I
35. 017K3.01 001/T2G I/T2G I/NATURAL CIRC/M 3.5*/3.7*/BANK/NA02301/C/RA/LM/LSM
If all core-exit thermocouples are inoperable during an event in which the RCPs were
tripped, what other indication(s) may be used to verify that natural circulation cooling is
occurring?
A. RCS hot leg temperature only.
B. RCS cold leg temperature only.
C.0 Both RCS cold leg and hot leg temperature.
D. There are no direct indications available.
REF: NA Bank 3796
OBJ: 12484
Time:
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: CCCDBCDCBB
Scramble Range: A - D
RO Tier:
T2G1
Key Word:
NATURAL CIRC
Source:
BANK
C
SRO Tier:
T2G I
Cog. Level:
M 3.5*/3.7*
Exam:
Misc:
NA02301
RA/LM/LSM
36. 017K4.01 001/T2G1//ICCM/M 3.4/3.7/BANK/NA02301/R/RA/LM
Which one of the following is the primary purpose of the subcooled margin monitor
subsystem associated with the Inadequate Core Cooling Monitor System?
The primary purpose is to provide indication of the:
A. pressure margin to saturation based on the wide-range Reactor Coolant System
pressure.
B. temperature margin to saturation based on the wide-range Reactor Coolant System
temperature.
C.t temperature margin to saturation based on the core-exit thermocouples.
D. pressure margin to saturation based on the wide-range Reactor Coolant System
temperature and pressure.
37
Tuesday, July 23, 2002 01:31:27 PM
Test:
I
REF:NA Bank 501
OBJ:
Distractor A: Incorrect - Subcooled margin monitor is based on a temperature margin.
Distractor B: Incorrect - Subcooled margin monitor utilizes core-exit thermocouples.
C: Correct
Distractor D: Incorrect- combination of
Time:
I
Points:
1.00
Version:
Answer:
RO Tier:
T2G1
Key Word:
ICCM
Source:
BANK
Test:
R
two incorrect statements.
0123456789
CCDCDADBAA
Scramble Range: A - D
SRO Tier:
Cog. Level:
M 3.4/3.7
Exam:
NA02301
Misc:
RA/LM
022K2.02 001/T2G I//POWER SUPPLY/M 2.5/2.4/BANK/NA02301/R/RA/LSM
Which one of the following is the power supply to the "A" outside recirc spray pump?
A. 4160-volt AC bus 1J.
B. 4160-volt AC bus 1H.
C. 480-volt AC bus 1J1.
D. 480-volt AC bus 1 H1.
Bank- ID: 280
Time:
I
RO Tier:
Key Word:
Source:
Test:
T2G I
POWER:
BANK
R
Points:
1.00
Version:
0 1 2 3 4 5 6 7
Answer: BDDBBDBC
SRO Tier:
SUPPLY
Cog. Level:
Exam:
Misc:
89
Scramble Range: A - D
M 2.5/2.4
NA02301
RA/LSM
Tuesday, July 23, 2002 01:31:28 PM
37
38
38. 022K4.03 001/T2GI/T2G1/3.6*/4.0/C/A 3.6/4.0/NEW/NA02301/C/RA/LSM/SC
A small leak has developed in the component cooling water supply line to the reactor
coolant pumps. An initial idea is to initiate a phase B containment isolation, which will
close the component cooling water supply trip valves to reactor coolant pumps.
Subsequent review has found this is not practical because of which one of the
following?
A. There is no provision for direct manual initiation of only a phase B signal without
first initiating a phase A signal.
B. There is no provision for direct manual initiation of only a phase B signal without
also initiating a CDA signal.
C. The direct manual initiation of only a phase B signal will also cause a phase A
signal which will shut all containment isolation valves for penetrations that are not
essential for an orderly cooldown of the reactor with the reactor coolant pumps
running.
D. The direct manual initiation of only a phase B signal will also cause a CDA signal.
There are two types of containment isolation signals: (a) phase A and (b) phase B.
The phase A containment isolation signal is initiated either automatically by a safety
injection actuation signal or manually by operator action. The phase A signal shuts all
containment isolation valves for penetrations that are not essential for an orderly
cooldown of the reactor with the reactor coolant pumps running. The phase B
containment isolation signal is initiated automatically when containment total pressure
exceeds 27.75 psia. There is no provision for direct manual initiation of only a phase B
signal without also initiating a CDA. The phase B signal completes containment
isolation by sending a close signal to containment isolation valves for component
cooling water used by the reactor coolant pumps, which will be secured by the control
room operator, the return from the containment recirculation air coolers, the steam
generator blowdown isolation valves (which are also closed by phase A) and instrument
air. Containment isolation must be reset before valves shut by either phase A or phase
B can be reopened. The equipment that generates the containment isolation signals is
more fully discussed in the Instrumentation and Controls section of this module.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BABABAACDB
Scramble Range: A - D
RO Tier:
T2G I
SRO Tier:
T2G I
Key Word:
3.6*/4.0
Cog. Level:
C/A 3.6/4.0
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:29 PM
39
39. 024AK3.01 001/TIGI//BORATION/M 4.1/4.4/M/NA0230I/R/RA/GWL/LSM/SC
- Unit 1 is operating at 50% power.
- The crew is required to evacuate the control room due to noxious fumes.
Which one of the following would require the crew to commence an emergency
boration in accordance with 1-AP-20, "Operation from the Auxiliary Shutdown Panel"?
A' The crew was unable to verify IRPI status before leaving the control room.
B. One control rod remains fully withdrawn, all other IRPIs indicate zero.
C. IRPIs for three control rods indicate six steps, all other IRPIs indicate zero.
D. The control room remains uninhabitable 18 hours2.083333e-4 days <br />0.005 hours <br />2.97619e-5 weeks <br />6.849e-6 months <br /> following the reactor trip.
North Anna Bank Question # 3779. Modified.
Changed conditions in answers to allow for another answer to be correct.
Changed the time on D to 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> instead of 16.
Changed # of rods and rod height.
A. correct. recent procedure change.
B. Incorrect, Shut down margin is calculated with the most reactive rod out of the core,
the
procedure directs the crew to emergency borate only if two or more rods
are out.
C. Incorrect - with three control rods indicated out greater than 10 steps out of the core
the
procedure calls for an emergency boration. This does not meet that
criteria
D. Incorrect, the previous procedure stated - the time is greater than 15 hours1.736111e-4 days <br />0.00417 hours <br />2.480159e-5 weeks <br />5.7075e-6 months <br /> and
requires emergency boration.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ABDAABDDDC
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
Key Word:
BORATION
Cog. Level:
M 4.1/4.4
Source:
M
Exam:
NA02301
Test:
R
Misc:
RA/GWL/LSM/SC
Tuesday, July 23, 2002 01:31:29 PM
40
40. 024G2.4.35 001//TIG1/BORATION/C/A 3.3/3.5/M/NAO2301/S/RA/LSM/SC
The control room has been evacuated due to an uninhabitable atmosphere. The 1-E-0
immediate actions were performed prior to evacuating the control room. The RO
reported that all IRPIs indicated zero except;
- 1 rod at 30 steps
- 1 rod at 20 steps
- 1 rod at 10 steps
Which
how it
one of the following describes how long emergency boration is required and
is initiated?
A. 25 minutes; by opening emergency borate valve from the auxiliary building.
B. 25 minutes; by opening emergency borate valve from the auxiliary shutdown panel.
C0 50 minutes; by opening emergency borate valve from the auxiliary building.
D. 50 minutes; by opening emergency borate valve from the auxiliary shutdown panel.
Reference required
1993/10/11 Modified bank to match new criteria of 25 minutes per rod changed AP
reference
1-AP-20, Rev. 18, page 8
Question modified on 06/04/02 to reflect accurate KA
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CCCDDCDADC
Scramble Range: A - D
RO Tier:
SRO Tier:
TIGI
Key Word:
BORATION
Cog. Level:
C/A 3.3/3.5
Source:
M
Exam:
NA02301
Test:
S
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:29 PM
41
41. 025AK3.03 00I/TiG2/TIG2/REFUELING/C/A 3.9/4. 1/BANK/NA02301/C/RA/LSM/SC
F-
Unit 1 is in mode 5 for an unscheduled maintenance outage.
The unit has been shutdown for 10 days.
RCS temperature is 130 0F.
RCS level is +11" above centerline.
Residual heat removal (RHR) pump 1-RH-P-1B is in service.
Both RHR heat exchangers are in service.
The reactor operator observes the following RHR parameters:
- RHR flow - fluctuating 2800 gpm plus or minus 200 gpm.
- RHR motor amps - fluctuating 35 plus or minus 5 amps.
- RCS standpipe level - fluctuating at +11 plus or minus 1 inch.
Which one of the following describes the RHR flow? The RHR flow is:
(1-AP-1 I is available for reference)
A' above design flow and can be reduced to 2250 gpm.
B. below design flow and can be raised to 2900 gpm.
C. below design flow and can be left at 2800 gpm.
D. above design flow and can be raised to 4000 gpm.
Tuesday, July 23, 2002 01:31:29 PM
42
Bank 3037
reference AP-1 1
Question replaced
Original Question
Stand pipe operation changed
Unit 2 is refueling and is on RHR. There has been a degradation of RHRSW causing
the running RHR pumps to cavitate. Unit 2 then enters 1-AP-11, LOSS OF RHR. The
RCS level stand pipe initially has dropped then began to slowly rise. You get initial
reports from the refueling floor that there is some boiling in the core. The caution in
1-AP-1 1 describes which one of the following effect on the RCS Level measurements?
Changes in RCS temperature due to boiling in the core can result in Reactor Vessel
water level changes that may not show on RCS standpipe level indicator.
Changes in RCS pressure due to boiling in the core can result in Reactor Vessel water
level changes that may not show on RCS ultrasonic level indicator.
Changes in RCS temperature due to boiling in the core can result in Reactor Vessel
water level changes that may not show on RCS ultrasonic level indicator.
Changes in RCS pressure due to boiling in the core can result in Reactor Vessel water
level changes that may not show on RCS standpipe level indicator.
Answer - D
Time:
I
RO Tier:
Key Word:
Source:
Test:
Points:
1.00
Version:
Answer:
TIG2
REFUELING
BANK
C
0123456789
AABDCCBBBA
Scr
SRO Tier:
T1G2
Cog. Level:
C/A 3.9/4.1
Exam:
NA02301
Misc:
RA/LSM/SC
amble Range: A - D
Tuesday, July 23, 2002 01:31:29 PM
43
42. 026AK3.03 001/T G I /TI G I/DEGRADED COOLING/C/A 4.0/4.2/BANK/NA0230I/C/RA/GWL/SC
- Unit 2 has entered 2-FR-C.2 "Response to Degraded Core Cooling"' due to
indications of degraded core cooling.
- "B" RCP is running, "A" and "C" have been secured.
- Component cooling water flow to the "B" RCP motor has just been lost.
Which one of the following describes the actions that should be taken in accordance
with 2-FR-C.2?
A. Secure the "B" RCP immediately; allowing it to run will cause core cooling to
degrade further.
B. Continue to operate "B" RCP; this will allow better pressure control of the Reactor
Coolant System.
C. Secure the "B" RCP immediately; damage to the motor windings could occur.
D. Continue to operate "B" RCP until directed by the procedure; the pump may
provide core cooling.
North Anna Bank question # 2540.
A. Incorrect, allowing the B RCP to continue to run could cause reflux cooling to take
place, this
will not degrade core cooling further.
B. Incorrect, Pressurizer sprays come off the A and C RCPs, not the B RCP.
C. Incorrect, The B RCP should remain running until directed by the procedure.
D. Correct, the B RCP should remain running the pump could provide some reflux
cooling.
Time:
1
RO Tier:
TIGI
Points:
1.00
Version:
0 1 23456789
Answer:
DCBAAADAAA
SRO Tier:
TIGI
Scramble Range: A - D
Key Word:
DEGRADED COOLING
Source:
BANK
Test:
Cog. Level:
C/A 4.0/4.2
Exam:
Misc:
C
NA02301
RA/GWL/SC
Tuesday, July 23, 2002 01:31:29 PM
44
43. 026K4.01 O0I/T2G2/T2GI/RECIRC SPRAY/C/A 4.2/4.3/BANK/NA02301/C/RA/LSM/SC
Which one of the following describes how the Recirculation Spray System would be
affected by a rupture outside containment in the quench spray pump discharge piping?
A. The additional source of water for the outside recirc spray [ORS] pumps will be lost
and ORS pump available NPSH will not be increased by reduced temperature of
the water at the suction of the ORS pumps.
B. The capacity of the Recirculation Spray System will be reduced by the loss of the
ORS pumps when the Quench Spray System is isolated.
C.f The additional source of water for the inside recirc spray [IRS] pumps will be lost
and IRS pump available NPSH will be decreased by the increased temperature of
the water at the suction of the IRS pumps.
D. The capacity of the Recirculation Spray System will be reduced by the loss of the
ORS pumps when the Quench Spray System is isolated; however, the IRS pump
NPSH will be increased by the increase in containment pressure due to the early
termination of quench spray.
NCRDOP-91.1-LP-3, Revision 4, Pages 12 & 13
1992 bank
Time:
1
Points:
1.00
Version: 0 1 2 3 4 5 6 7 8 9
Answer: CCCABCBDBB
Scramble Range: A - D
RO Tier:
T2G2
SRO Tier:
T2G1
Key Word:
RECIRC SPRAY
Cog. Level:
C/A 4.2/4.3
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:29 PM
45
44. 027AK3.04 001/T G I /T I G2/PZR/C/A 2.8/3.3/NEW/NA02301/C/RA/GWL/LSM/SC
- Unit 1 has had a reactor trip and safety injection due to a main steam line break.
- The steam break was isolated prior to the diagnostic steps in 1 -E-0.
- l-E-0 has been completed.
- The crew is performing actions in 1-ES-1.1, "SI Termination."
- PRZR level is 22% and slowly rising.
- PRZR heaters have been energized.
- PRZR pressure is 1900 psig.
- The crew desires to raise pressure to normal operating pressure.
Which one of the following describes how and why PRZR pressure will respond when
compared to normal steady state conditions.
A. Pressure will rise more rapidly than normal due to charging flow being maximized,
and the bubble being compressed.
B.' Pressure will rise more slowly than normal due to the liquid in the pressurizer being
subcooled.
C. Pressure will rise more rapidly than normal due to letdown being placed in service,
preheating the charging flow.
D. Pressure will rise more slowly than normal due to the pressurizer vapor space
temperature being higher than normal.
A. Incorrect, Cooler water has entered the pressurizer, the actions of SI termination
have the crew maintain charging flow to maintain pressurizer level but charging flow will
not be maximized. (initial conditions pressurizer level 22% and slowly rising.
B. Correct, the water in the pressurizer is subcooled and will require time to heat,
therfore pressure rise will be slower when compared to normal steady state conditions.
C. Incorrect, placing letdown in service will tend to lower pressurizer pressure, so the
pressure rise would be slower.
D. Incorrect, pressurizer vapor space temperature will be lower than normal, based on
Psat-Tsat conditions.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BBCBACBCCD
Scramble Range: A - D
RO Tier:
TIGi
SRO Tier:
TIG2
Key Word:
PZR
Cog. Level:
C/A 2.8/3.3
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/GWL/LSM/SC
Tuesday, July 23, 2002 01:31:29 PM
46
45. 028K5.04 00l/T2G3/T2G2/HYDROGEN/M 2.6/3.2*/BANK/NA02301/C/RA/LSM
Which one of the following describes the design basis of the hydrogen recombiner?
A' Reduce hydrogen concentration from 4% to 0.5% at a flow rate of 50 SCFM.
B. Maintain hydrogen concentration less than 6% following a LOCA with zirc-water
reaction.
C. Reduce hydrogen concentration from 15% to 4% in less than 10 days following a
LOCA.
D. Maintain hydrogen concentration less than 6% in less than 10 days following a
LOCA.
L.P. NCRODP-91 .2-LP-1, Rev. 6, p. 29, Objective G
1992 bank
Time:
I
Points:
1.00
Version:
0 1 23456789
T2G3
BANK
C
Answer: ABABDCBA
SRO Tier:
Cog. Level:
Exam:
Misc:
C B
Scramble Range: A - D
T2G2
M 2.6/3.2"
NA02301
RA/LSM
46. 029EA2.09 001//TI G I/REACTOR TRIP/M 4.4/4.5/NEW/NA02301/S/RA/LSM/SC
Unit one has had a turbine trip, but the reactor did not trip and the generator output
breaker did not open. The RO verifies automatic rod insertion and verifies the turbine
is tripped. Which one of the following describes the procedurally-required actions if the
generator output breaker cannot be verified open within 30 seconds?
A. Manually open G-12 ONLY.
B. Manually open exciter field breaker ONLY.
C.' Manually open both G-12 and the exciter field breaker.
D. Manually open either G-1 2 or the exciter field breaker.
both must be opened
reference 1-FR-S.1 step 2.d RNC
Time:
I
Points:
1.00
RO Tier:
Key Word:
Source:
Test:
NEW
S
Version:
0 1 23456789
Answer: CAAACAAABB
SRO Tier:
TiGI
Cog. Level:
Exam:
Misc:
Scramble Range: A - D
M 4.4/4.5
NA02301
RA/LSM/SC
Tuesday, July 23, 2002 01:31:30 PM
RO Tier:
Key Word:
Source:
Test:
47
47. 029K4.03 0OI/T2G2/T2G2/PURGE/M 3.2/3.5/BANK/NA02301/C/RA/LM/SC
Which one of the following conditions will automatically trip the containment purge
supply fans?
A0 Containment particulate radiation monitor hi-hi alarm.
B. Safety injection.
C. CDA.
D. Vent stack "B" radiation monitor hi-hi alarm.
Bank supplied by Utility for this exam.
Changed K/A since orginal selected K/A did not apply to North Anna. There was no
physical connection between the CTMT and the purge system blowers. The original
question also required the operator to know from memory a caution in an OP. This was
not considered information an operator should have memorized.
Which one of the following describes the precautions to be taken BEFORE operating a
purge blower?
Containment pressure must be atmospheric, RCS temperature < 200 degrees F.
Break containment vacuum using MOV-HV-1 QOB and ensure reactor shut down.
Pressurize containment to atmospheric, verify RCS temperature < 250 degrees F,
bypass filters unless particulate is high.
Be in Mode 6, RCS temperature < 200 degrees F, containment pressure within 4 psi of
atmospheric.
L.P. NCRODP-91.2-LP-1, Rev. 6, page 33, Objective G
1-OP-21.2 Containment Purge, Rev. 13, page 2 & 3 of 8
1992 bank
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ABACBAAADA
RO Tier:
T2G2
SRO Tier:
T2G
Key Word:
PURGE
Cog. Level:
M 3
Source:
BANK
Exam:
NA(
Test:
C
Misc:
RA/
Sc
i2
.2/3.5
02301
LM/SC
ramble Range: A - D
Tuesday, July 23, 2002 01:31:30 PM
48
48. 032AA2.09 00//T1G2/SOURCE RANGE/M 2.5/2.9/BANK/NA02301/S/RA/LSM/SC
Your shift is in the process of performing a reactor startup, and the reactor operator is
withdrawing control rods to take the reactor critical. As reactor power increases, the
reactor operator can manually block the source-range nuclear instruments after
verifying which one of the following?
A. Both intermediate-range detectors are properly compensated by indicating within
one-half decade of each other.
B. The intermediate-range detectors have both increased at least one decade from the
bottom of their scale.
C. Both intermediate-range detectors are indicating on-scale.
Do At least a one decade overlap between the source-range and intermediate-range
detectors.
replaced question - KA was not applicable to NA
Replaced KA on 06/05/02
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: DDBBAAC
SRO Tier:
SOURCERANGE
BANK
S
D DC
TIG2
Scramble Range: A - D
Cog. Level:
M 2.5/2.9
Exam:
NA02301
Misc:
RA/LSM/SC
034K4.02 001/T2G3//HOIST/M 2.6/3.4/BANK/NA02301/R/RA/LSM
Which one of the following describes the conditions which render the manipulator
crane bridge AND trolley inoperative simultaneously?
A. The upender is in the vertical position in the fuel transfer canal.
B. The trolley bypass is engaged.
C." The hoist is being operated or the gripper tube is down.
D. The Dillon load cell indicates 1200 pounds or greater.
L.P. NCRODP-92.9-LP-3, Rev. 2, p. 37, Objective D
1992 bank
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CCBDACDDDD
RO Tier:
T2G3
SRO Tier:
Key Word:
HOIST
Cog. Level:
M 2
Source:
BANK
Exam:
NAO
Test:
R
Misc:
RA/
Scramble Range: A - D
.6/3.4
)2301
LSM
Tuesday, July 23, 2002 01:31:30 PM
RO Tier:
Key Word:
Source:
Test:
49.
49
50. 035K6.03 00 /T2G2/T2G2/S/G LEVEL/C/A 2.6/3.0/NEW/NA02301/C/RA/LSM/SC
The crew has entered 1-AP-3, "Loss of Vital Instrumentation," due to the failure of "B"
steam generator level channel I1l. In accordance with 1-AP-3, which one of the
following describes the actions that must be taken?
A. There are no required actions.
B. Place the associated main feed reg valves in MANUAL ONLY.
C.0 Place BOTH the associated main feed reg valves and bypass valves in MANUAL.
D. Select steam generator level channel II as controlling channel.
1-AP-3 LOSS OF VITAL INSTRUMENTATION 2 of 15
[ 2] VERIFY STEAM GENERATOR LEVEL
Do the following:
CONTROL PARAMETERS - NORMAL:
.. Steam Flow
-..Feed Flow
"-Steam Generator Level Ch III
. Steam Pressure - *
Time:
I
RO Tier:
Key Word:
Source:
Test:
T2G2
S/G LEV
NEW
C
a) Place the associated valves in
MANUAL
Main Feed Reg Valves
Main Feed Reg Bypass Valves
b) Control Steam Generator level
Points:
1.00
Version:
0 1 2345 6789
Answer: CCDBBABACA
Scramble Range: A - D
SRO Tier:
T2G2
EL
Cog. Level:
C/A 2.6/3.0
Exam:
NA02301
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:30 PM
50
51. 036AA2.02 001//TIG3/3.4/4. I/M 3.4/4.l/MINA02301/S/RA/LSM/SC
During the refueling of unit 2, a fuel assembly was placed in the wrong location. Per
transient and accident analysis, this mistake could be found by which one of the
following?
A. During the performance of the normal required calorimetric.
B. By observing the axial flux differential.
C.f During the incore flux mapping.
D. By observing differences in the hotleg temperatures.
Replaced with Bank question- original not required knowledge and not the normally
required SRO actions.
Reference:
MODULE NCRODP-48 FUEL HANDLING SYSTEM
Inadvertent loading of a fuel assembly into an improper position. This accident analysis
assumes that a fuel assembly is placed in the wrong position in the core. An example
is the inadvertent loading of a fuel assembly position requiring burnable poison rods
with an assembly not having burnable poison rods. The power distortion due to any
combination of misplaced fuel assemblies would significantly raise peaking factors and
would be readily observable with in-core flux monitors. Core thermocouples would also
indicate any abnormally high coolant enthalpy rise. In-core flux measurements are
taken during the startup following the refueling operations. The results of this analysis
concluded that fuel assembly loading errors are prevented by administrative
procedures implemented during core loading. In the unlikely event that a loading error
occurs, the power distribution effects either will be readily detected by the in-core
movable detector system or will cause sufficiently small perturbation to be acceptable
within the uncertainties allowed between nominal and design power shapes.
KA typo corrected on 06/05/02
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CAAABBBBCD
Scramble Range: A - D
RO Tier:
SRO Tier:
TIG3
Key Word:
3.4/4.1
Cog. Level:
M 3.4/4.1
Source:
M
Exam:
NA02301
Test:
S
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:30 PM
51
52. 037AK1.02 001/TG2/TI G2/3.5/3.9/C/A 3.5/3.9/M/NAO2301/C/RA/LSM
Given the following conditions:
-
The unit was operating at 100% power.
-
A major steam line rupture occurred on the "A" SG.
-
An automatic SI was received.
-
All systems responded as designed.
-
The operating crew is now in the later steps of 1-E-2, "Faulted Steam Generator
Isolation."
-
PRZR level has suddenly started decreasing.
-
PRZR pressure is 2100 PSIG and decreasing.
-
1-MS-RM-170 ("A" SG steamline radiation monitor) has a valid high alarm.
Based on the above information, the crew should do which one of the following?
A. Upon completion of 1-E-2, transition to 1-ES-0.0.
B. Immediately enter 1-E-0.
C. Upon completion of 1-E-2, transition to 1-E-1.
DW Upon completion of 1-E-2, transition to 1-E-3.
VISION OBJ. 13842
modified - bank 1996/01/29
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: DADAADAACC
Scramble Range: A - D
RO Tier:
TIG2
SRO Tier:
T1G2
Key Word:
3.5/3.9
Cog. Level:
C/A 3.5/3.9
Source:
M
Exam:
NA02301
Test:
C
Misc:
RA/LSM
Tuesday, July 23, 2002 01:31:30 PM
52
53. 038EA2.09 001//TIG2/4.2/4.2/C/A 4.2/4.2/NEW/NA02301/S/RA/LSM
Which one of the following conditions support or indicate natural circulation flow in
accordance with 1-E-3, Attachment 1, Natural Circulation Verification?
A. SG pressures - stable or decreasing
RCS hot-leg temperatures - at saturation temperature
RCS cold-leg temperatures - stable or decreasing
B. SG pressures - stable or decreasing
RCS hot-leg temperatures - stable or decreasing
RCS cold-leg temperatures - stable or decreasing
C.f SG pressures - stable or decreasing
RCS hot-leg temperatures - stable or decreasing
RCS cold-leg temperatures - at saturation temperature for
for SG pressure
SG pressure
D. SG temperature - at saturation temperature for SG pressure
RCS hot-leg temperatures - stable or decreasing
RCS cold-leg temperatures - stable or decreasing
Reference
1-E-3 Attachment 1 NATURAL CIRCULATION VERIFICATION
NOTE: The following conditions support or indicate natural circulation flow.
1. 1. 1. VERIFY NATURAL CIRCULATION FLOW
.. SG pressures - STABLE OR DECREASING
Core Exit TCs - STABLE OR DECREASING
.. RCS Cold Leg temperatures - AT SATURATION TEMPERATURE FOR SG
PRESSURE
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CACBDBDBAD
Sc
SRO Tier:
TIG2
Cog. Level:
C/A 4.2/4.2
Exam:
NA02301
Misc:
RA/LSM
ramble Range: A - D
Tuesday, July 23, 2002 01:31:30 PM
RO Tier:
Key Word:
Source:
Test:
4.2/4.2
NEW
S
53
54. 038EK3.08 001/TI G2//RCP TRIP/M 4.1/4.2/NEW/NA02301/R/RA/GWL/LSM/SC
- Unit 2 has had a steam generator tube rupture.
- The crew is performing 2-E-3.
- At the step for checking RCP trip and charging pump recirc criteria the crew
determines that all RCPs must be tripped.
Which one of the following correctly describes the reason for tripping the RCPs during
a SGTR event when the trip criteria is met?
A. This will ensure core cooling during a steam generator tube rupture event.
B.0 To minimize the effects of a misdiagnosis of the fault or a multiple failure event.
C. To reduce RCS pressure, since this will slow the rate of in-leakage into the steam
generator.
D. To allow natural circulation cooling to develop, since this will expedite steam
generator cooldown.
NCRODP-92-LP-5. North Anna Steam Generator Tube Rupture lesson plan page 10.
WOG Background document.
A. Incorrect, Tripping the RCP's during a tube rupture event is to minimize the effects of
a
misdiagnosis. Core cooling would be better if the RCPs were left running.
B. Correct, lAW the WOG the tripping of the RCPs during a tube rupture event is so
that the
event will not be misdiagnosed if for some reason later the pumps were
tripped/or lost at an
inconvient time (a time that might mask the diagnosis).
C. Incorrect, stopping the RCPs will actually take away one of the methods for pressure
reduction (sprays) securing the pumps will only slightly lower pressure and
then is will be
determined by heat input from the core and leak rate.
D. Incorrect, Stopping the pumps would not in themselves does not allow natural
circulation to
develop, the pumps must be stopped for natural circ cooling to occur
but steam generator
position and steam flow actually determine (delta T) natural
circ flow. This would not
expedite the cooldown.
Time:
I
Points:
1.00
Version:
0 1 2 34 5 6 7 8 9
Answer: BBCCBCBBBC
Scramble Range: A - D
RO Tier:
T1G2
SRO Tier:
Key Word:
RCP TRIP
Cog. Level:
M 4.1/4.2
Source:
NEW
Exam:
NA02301
Test:
R
Misc:
RA/GWL/LSM/SC
Tuesday, July 23, 2002 01:31:30 PM
54
55. 039K5.08 001/T2G2/T2G2/MSRJC/A 3.6/3.6/NEW/NA02301/C/LSM/LM/GH/SC
Which one of the following would be the effects on reactor power and enthalpy of the
HP turbine exhaust steam entering the MSR if scaling of the heat exchanger reduces
the MSR's efficiency by 50%? (Ignore any slight changes in ambient losses or gains).
AO Reactor power would increase and enthalpy would remain unchanged.
B. Both reactor power and enthalpy would increase.
C. Both reactor power and enthalpy would decrease.
D. Reactor power would decrease and enthalpy would remain unchanged.
Solution: a
Reactor power would increase because feedwater temperature would not be heated by
the MSR. Enthalpy at the inlet of the MSR's would remain at the enthalpy of the outlet
of the first stage of the turbine turbine which should essentially remain unchanged.
NCRODP23
Assume that at full power operation 9,798,706 Ibm/hr of wet steam exits the HP turbine
and enters the MSRs at an enthalpy (h) of 1115.5 Btu/lbm and a pressure of 230 psia.
The quality (X) of the steam entering the MSRs is determined by solving the
thermodynamic formula; h = hf + X hfg for X, and by finding the values for hf (368.3)
and hfg (831.8), corresponding to a saturation pressure of 230 psia, in the steam
tables:
X = (h - hf)/hfg
The quality of the inlet steam to the MSRs in this example is 89.8 percent. The MSRs
remove approximately 10 percent (988,745 Ibm/hr) of this mass in the form of moisture
(100 percent of the liquid). Thus, the steam entering the MSR tube bundle is dry,
saturated steam (X=1 00 percent). The enthalpy of the steam entering the tube bundle
is
h = hf + X hfg, or
h = 368.3 + 100(831.8), or
h = 1200.1 Btu/lbm.
Time:
I
Points:
1.00
Version: 0 1 23456789
Answer: AACBABDBBD
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:31 PM
55
RO Tier:
T2G2
Key Word:
Source:
NEW
Test:
C
SRO Tier:
T2G2
Cog. Level:
C/A 3.6/3.6
Exam:
NA02301
Misc:
LSM/LM/GH/SC
56. 041 K6.03 O01/T2G3/T2G3/STEAM DUMPS/C/A 2.7/2.9/BANK/NA02301/C/LSM/LM/SC
During operation of the Steam Dump System in the steam pressure mode, which one
of the following describes how the arming signal is cleared?
A. By shifting the steam header pressure controller to MANUAL and decreasing signal
demand to zero.
B./ Place the Steam Dump Mode Selector Switch to the Tavg mode.
C. Place the Steam Dump Interlock Switch to OFF/RESET and return the switch to the
ON position.
D. Place the Steam Dump Interlock Switch to the BYPASS INTERLOCK position.
bank - 1992/03/16 Surry
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6
Answer: BBBBACB
RO Tier:
T2G3
SRO Tier:
Key Word:
STEAM DUMPS
Cog. Level:
Source:
BANK
Exam:
Test:
C
Misc:
789
A B B
Scramble Range: A - D
T2G3
C/A 2.7/2.9
NA02301
LSM/LM/SC
Tuesday, July 23, 2002 01:31:31 PM
56
57. 045K4.34 001/T2G3/T2G3/ROD CONTROL/C/A 2.7/2.9/NEW/NA02301/C/RA/GWL
- Unit 1 has ramped to 12% power due to maintenence concerns.
- PT-1446 and PT-1447 indicate approximately 12% turbine load.
- Rod control has been left in AUTOMATIC from the ramp down.
- Steam dumps have been taken to the steam pressure mode in preparation for
removing the turbine.
- The RO inadvertently opens the steam dumps until reactor power indicates 17% on
N-41 and N-42, and 16% on N-43 and N-44.
- RCS temperature lowers to 543°F.
Which one of the following describes the effect this failure will have on the Rod Control
System?
A. Control rods will step out at 40 spm until Tave and Tref are within 1.5 degrees.
B.' Control rods will NOT step out due to control interlock C-5 not being satisfied.
C. Control rods will step out at 32 spm until Tave and Tref are within 1.5 degrees.
D. Control rods will NOT step out due to permissive P-10 not being satisfied.
NCRODP-77-NA Objective I, NCRODP-65, Objective A and D.
A. Incorrect, Rods will not step out in auto due to turbine load being < 15%.
B. Correct, Rods will not step out due to turbine load being < 15% and C-5 not allowing
auto rod
motion.
C. Incorrect, Rods will not step out due to turbine load.
D. Incorrect, Rods will not step out and P-10 does not effect auto-rod motion.
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: BBCABCADAC
Scramble Range: A - D
RO Tier:
T2G3
SRO Tier:
T2G3
Key Word:
ROD CONTROL
Cog. Level:
C/A 2.7/2.9
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/GWL
Tuesday, July 23, 2002 01:31:31 PM
57
58. 051AA2.02 001//TI 01/3.9/4.1/C/A 3.9/4.1/NEW/NA02301/S/RA/LSM/SC
Unit 1 is at 100% power.
- The RO reports that you have degrading condenser vacuum and decreasing
generator output.
- You direct the crew to enter 1-AP-14, "Low Condenser Vacuum."
- Reactor power has been reduced to 60%, condenser pressure is now 5.6 inches of
Hg absolute.
Which one of the following is the correct action?
A. Exit 1-AP-14 and go to 1-E-0.
B.0 Go to 1-E-0 and complete 1-AP-14.
C. Complete 1-AP-14 and then go to 1-E-0
D. Place condenser hogger ejectors in service per 1-OP-36.1.
Reference - 1-AP-14, revision 17
a 1-E-0 does not contain sufficient guidance for this condition, must also remain in the
b correct per step 4, RNO
c Have reached reactor trip criteria for Condenser pressure, must enter 1-E-0
d only appropriate, if pressure had not degraded
Time:
1
Points:
1.00
Version:
0 1 23456789
Answer: BCDBBBCDAD
Scramble Range: A - D
RO Tier:
SRO Tier:
TIGI
Key Word:
3.9/4.1
Cog. Level:
C/A 3.9/4.1
Source:
NEW
Exam:
NA02301
Test:
S
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:31 PM
58
59. 055EK1.02 001/T1G1/T1G1/CSFST/C/A 3.3/3.7/BANK/NA02301/C/RA/LSM
VISION OBJ. 13835 (LORP)
BANK 1996/01/29
Time:
I
Points:
1.00
Version:
0 1 2345 6789
Answer: AABBBDDACA
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
TIGI
Key Word:
Cog. Level:
C/A 3.3/3.7
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/LSM
60. 055K3.01 001/T2G2//CONDENSER/C/A 2.5/2.7/M/NA02301/R/RAILSM/SC
Unit 1 is 18% power during startup.
- A malfunction causes all condenser waterbox vacuum breakers to open.
- Condenser pressure is 5.0 inches Hg absolute and increasing.
Which one of the following is the required immediate action?
A. Reduce turbine load until condenser vacuum is stable.
B. Trip the turbine and go to 1-AP-2.1, Turbine Trip without Reactor Trip Required.
C. Trip the turbine and reduce reactor power to less than 5%.
DO Go to 1 -E-0, Reactor Trip or Safety Injection.
1-AP-14, Rev. 9, page 2
1993 bank
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: DBBCCAABAB
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:31 PM
When depressurizing SGs in 1-ECA-0.0, the operator is directed to check RCS Tcold
> 315°F during the depressurization to ensure that the evolution does NOT do which
one of the following?
Af Challenge the integrity critical safety function.
B. Disrupt natural circulation.
C. Create a void in the reactor vessel upper head.
D. Inject nitrogen from the SI accumulators into the RCS.
59
RO Tier:
Key Word:
Source:
Test:
T2G2
CONDENSER
M
R
SRO Tier:
Cog. Level:
Exam:
Misc:
C/A 2.5/2.7
NA02301
RA/LSM/SC
61. 056A2.04 001/T2G 1/T2G 1/CONDENSATE/C/A 2.6/2.8/NEW/NA02301/C/RA/LM/LSM/SC
REF: MODULE NCRODP-25 MAIN CONDENSATE SYSTEM pages 62-63
OBJ: 2.19
Distractor B - PS-CN-11 8A is the condensate pump discharge header pressure.
Header pressure will not decrease on a pump start.
Distractor C - A faulted speed switch will result in the associated pump tripping and
auto-start of the third pump.
Distractor D - A drop in Feedwater suction pressure is not characteristic with starting a
second condensate pump.
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
T2G I
CONDENSATE
NEW
C
Answer: ADADBADD
SRO Tier:
Cog. Level:
Exam:
Misc:
C C
Scrambl
T2G I
C/A 2.6/2.8
NA02301
RA/LM/LSM/SC
[e Range: A - D
Tuesday, July 23, 2002 01:31:31 PM
- Unit 1 is operating at 5% power
- "B" condensate pump is running.
- "C" condensate pump is in AUTO.
- "A" condensate pump is manually started.
- "C" condensate pump auto starts
Which one of the following is the most probable cause of "C" condensate pump starting
and what action should be taken?
Ar Caused by the "C" handswitch being in the AUTO position when starting the "A"
condensate pump. The "C" condensate pump should be shutdown per normal
operating procedures.
B. Starting "A" condensate pump dropped pressure sensed by PS-CN-1 18A to below
440 psig, an auto-start for "C". The "C" condensate pump should be shutdown per
normal operating procedures.
C. Caused by false low hotwell level generated because the "B" pump was running
when starting the "A" condensate pump. The "C" condensate pump should be
shutdown per normal operating procedures.
D. Caused by a drop in feedwater suction pressure below 280 psig, characteristic of
starting a second condensate pump at this power level. Notify the Shift Supervisor.
RO Tier:
Key Word:
Source:
Test:
60
62. 056AK3.02 001/T1G3//ECA-0.0/C/A 3.5/3.9/NEW/NA02301/R/RA/LSM/SC
NEW
Reference
1-ECA-0.0 Revision 18, Caution before step 9 page 6 of 18
distractor analysis - this is only done because of loading concerns, the SI is required to
be reset to allow the manual loading of a recovered EDG.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CABACDCBAC
Scramble Range: A - D
RO Tier:
T1G3
SRO Tier:
Key Word:
ECA-0.0
Cog. Level: C/A 3.5/3.9
Source:
NEW
Exam:
NA02301
Test:
R
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:31 PM
- Unit 1 is at 100 % power and a lost off-site power has occurred.
- Both Unit 1 EDGs failed to start.
- The crew enters 1-ECA-0.0.
- An SI occurred during steam generator depressurization, then power to 1 H bus was
restored from 1 H EDG.
Which one of the following describes your required actions, and the reason for those
actions?
A. The SI should NOT be reset to allow automatic loading of equipment on the 1 H bus.
B. The running SI pumps should be stopped, operators must manually load equipment
on the 1H bus in a controlled fashion per 1-ECA-0.0 to prevent overloading the
EDG.
C.f The SI should be reset to allow manual loading of equipment on the 1 H bus.
D. The SI should NOT be reset, the running SI pumps should be stopped because of
sequencing and loading concerns on the 1 H bus.
61
63. 057AA1.06 00I/TIG1/TIG1/MANUAL CONTROL/C/A 3.5/3.5/BANK/NA02301/C/RA/LSM
BANK 1996
VISION OBJ. 11550
Time:
I
Points:
1.00
RO Tier:
Key Word:
Source:
Test:
TIGI
MANUAL CONTROL
BANK
C
Version:
0 1 234567
Answer: BCACCCBD
SRO Tier:
Cog. Level:
Exam:
Misc:
89
D C
Scramble Range: A - D
T1GI
C/A 3.5/3.5
NA02301
RA/LSM
Tuesday, July 23, 2002 01:31:31 PM
Given the following conditions:
-
Unit 1 is at 35% power.
-
While hanging a tagout, an operator opened the wrong breaker and de-energized
the power to 1-DA-TV-100B, containment sump pump discharge valve.
-
The mispositioned breaker has been re-closed lAW procedures.
-
J-A6, "RX CONT SUMP HI LEVEL" has alarmed.
In order to pump the containment sump, the operator will have to do which one of the
following?
A. Push the OPEN button for 1-DA-TV-100B.
BH Push the CLOSE button for 1-DA-TV-1 00B.
C. Cycle 1 -DA-P-1 B to OFF, then back to AUTO.
D. Reset phase "A" isolation, train "B".
62
64. 058AK3.02 001/T 0G2/TI G2/LOSS OF DC POWER/C/A 4.0/4.2/M/NA02301/C/RA/LSM/SC
1996 Bank
NCRODP-35-LP-1 OBJ. B, NCRODP-41-LP-1 OBJ. G
Time:
I
Points:
1.00
Version:
0 1 23456789
RO Tier:
TIG2
Key Word:
LOSS
Source:
M
Test:
Answer: BCAACADACA
SRO Tier:
T1G2
OF DC POWER
Cog. Level:
Exam:
Misc:
C
Scramble Range: A - D
C/A 4.0/4.2
NA02301
RA/LSM/SC
Tuesday, July 23, 2002 01:31:32 PM
Given the following:
-
Unit 1 was operating at 100 percent power.
-
1-CH-P-1A was running.
-
A loss of DC control power to the 1J bus has occurred.
-
While stabilizing the unit, a spurious SI occurred.
As you enter E-0, which one of the following pump combinations will exist as a result of
these failures?
A. 1-CH-P-1A not running, 1-CH-P-1B running, 1-CH-P-1C running.
B. 1-CH-P-1A running, 1-CH-P-1B not running, 1-CH-P-1C not running.
C. 1-CH-P-1A running, 1-CH-P-1B running, 1-CH-P-iC not running.
D. 1-CH-P-1A running, 1-CH-P-lB not running, 1-CH-P-IC running.
63
65. 059A3.02 001/T2G1/T2G1/STEAM PRESSURE/C/A 2..9/3.1/BANK/NA02301/C/RA/LM/GH/LSM/SC
The following plant conditions exist:
- Reactor power is 100%
- Rod control is in AUTO
- Steam generator level control is in AUTO
- Steam generator level control inputs (steam flow, feed flow, turbine first stage
pressure) are selected to channel III
With NO OPERATOR ACTION, which one of the following conditions describes the
effect on plant operation when channel III steam pressure in "A"
low?
A. Increased feed flow results in steam generator shrink, steam
stabilizes at a slightly higher level.
B. Decreased feed flow results in steam generator swell, steam
stabilizes at a slightly lower level.
C.' Decreased feed flow results in a reactor trip.
D. Increased feed flow results in a Hi-Hi steam generator level.
steam generator fails
generator level
generator level
REF: NCRODP26 Main Feedwater p77-81
OBJ:
SOURCE: Braidwood 4/1/96
Distractor A - Incorrect -feed flow would decrease.
Distractor B - Incorrect - swell in not caused by decreased feed flow.
Distractor D - Incorrect - feed flow would decrease.
Comment: The mass flow rate of steam is directly proportional to the density of steam,
which is proportional to the square root of steam pressure. Loss of steam pressure
transmitter appears to the Steam Generator Water Level Control system as a decrease
in steam flow.
Time:
I
RO Tier:
Key Word:
Source:
Test:
T2GI
STEAM I
BANK
C
Points:
1.00
Version:
0 1 2345 6789
Answer: CCDBABBCDC
Scramble R
SRO Tier:
T2G I
PRESSURE
Cog. Level:
C/A 2..9/3.1
Exam:
NA02301
Misc:
RA/LM/GH/LSM/SC
ange: A - D
Tuesday, July 23, 2002 01:31:32 PM
64
66. 059AK3.03 00I/TI G2/TI1G1/RADWASTE/M 3.0/3.7/M/NA02301/C/RA/LSM
Assume the following conditions:
- A liquid radwaste release is in progress.
- Unit I is operating at 15% power.
- Unit 2 is in a forced maintenance outage due to multiple condenser tube failures.
- Unit-2 water boxes are tagged out and drained for repairs.
- The liquid effluent radiation monitor has been declared inoperable.
- Health Physics has taken a grab sample and the results indicate the release may
continue.
1-CW-P-IC has just tripped, leaving the "A," "B," and "D" pumps running.
Which one of the following actions must be taken?
Af Secure all liquid waste releases.
B. Trip the reactor and enter 1-E-0.
C. Align liquid waste releases to unit-2 discharge tunnel.
D. Trip the turbine and enter 1-AP-2.1.
A. Not enough dilution water flow
Modified bank ID: 3121
Time:
I
Points:
1.00
Version:
0 I 2 34567 89
Answer: AACBABACCD
Scramble Range: A - D
RO Tier:
T1G2
SRO Tier:
TIGI
Key Word:
RADWASTE
Cog. Level:
M 3.0/3.7
Source:
M
Exam:
NA02301
Test:
C
Misc:
RA/LSM
67. 059K4.16 001/T2G 1//FEED PUMP TRIP/M 3.1 */3.2*/BANK/NA0230 1 /R/RA/LSM/SC
Which one of the following conditions will cause a main feedwater pump to trip?
A. "A" main feedwater pump will trip if its lube oil pressure is 7 psig.
B. "A" or "B" main feedwater pumps will trip on low condenser vacuum.
C. "B" main feedwater pump will trip if suction pressure is < 300 psig for 45 seconds.
Df Undervoltage on "A" 4160-volt station service bus will cause "A" main feedwater
pump to trip.
Tuesday, July 23, 2002 01:31:32 PM
65
REF: NA Bank 3365
OBJ:
Distractor A - Incorrect
Distractor B - Incorrect
Distractor C - Incorrect
Time:
I
Points:
RO Tier:
T2G I
Key Word:
FEED PUMP TRII
Source:
BANK
Test:
R
68. 060G2.4.11 00l//TlG2/3.7/4.3/1
lube oil pressure less than 5 psig causes trip.
there is no low condenser vacuum trip
suction pressure less than 280 psig for 55 sec for B pump
1.00
Version:
0 1 23456789
Answer: DCDCABCAAC
Scramble Range: A - D
SRO Tier:
P
Cog. Level:
M 3.1*/3.2*
Exam:
NA02301
Misc:
RA/LSM/SC
4 3.4/3.6/BANK/NA02301/S/RA/LSM
BANK ID: 2676
KA modified on 06/05/02
Time:
I
Points:
RO Tier:
Key Word:
3.7/4.3
Source:
BANK
Test:
S
1.00
Version: 0 1 234567
Answer: ADBCDCCD
SRO Tier:
Cog. Level:
Exam:
Misc:
89
B D
Scramble Range: A - D
TIG2
M 3.4/3.6
NA02301
RA/LSM
Tuesday, July 23, 2002 01:31:32 PM
While operating with primary-to-secondary leakage, steam release from the which one
of the following does NOT require entry into 0-AP-54, "Accidental, Unplanned, or
Uncontrolled Radioactive Gaseous Waste Release?"
A0 Containment hogger discharge.
B. Main condenser hogger discharge.
C. Decay heat release valve.
D. Steam generator power-operated relief valve.
66
69. 061K1.07 001/T72G01/T2G 1/FIRE PROTECTION/C/A 3.4/3.7/BANK/NA02301/C/RA/LSM/LM
With AFW in service to supply feedwater, ECST level suddenly begins to decrease
rapidly due to a rupture in the tank.
Which ONE of the following water sources should be aligned to supply AFW pump
suction?
A. Standby 300,000-gallon condensate storage tank.
B. In-service 300,000-gallon condensate storage tank.
C. Fire Protection System using diesel-driven pump 1-FP-P-2.
DO Fire Protection System using motor-driven pump 1-FP-P-1.
REF: 1-AR-F-E8; 1-AP-22.5; 1-OP-31.2.
OBJ: 5971
COMMENT: Answer correct: Fire protection using lake water is the preferred source;
1-FP-P-1 takes suction on the lake.
Distractors A & B: - candidate misconception concerning piping configuration for CST
supply to AFW system. CST cannot be aligned to supply suction directly to the AFW
pumps, only to makeup to the ECST; since the ECST is ruptured, this is not an option.
Distractor C - fire protection system is the preferred alternate suction source.
Distractors wrong:
diesel-driven pump takes suction from the service water reservoir.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: DAAABCCCAA
Scramble Range: A - D
RO Tier:
T2GI
SRO Tier:
T2G1
Key Word:
FIRE PROTECTION
Cog. Level:
C/A 3.4/3.7
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/LSM/LM
Tuesday, July 23, 2002 01:31:32 PM
67
70.061 K4.04 O01/T2G 1//AUX FEED WATER/M 3.1 /3.4/NEW/NA02301/R/RA/LSM/GH/SC
Which one of the following describes the design features that limit the maximum flow
from each of the AFW pumps in the event of a piping rupture?
A' An orifice is installed on the discharge header of the turbine-driven pump. A PCV is
installed on the discharge header of each motor-driven pump.
B. An orifice is installed on each pump's discharge header.
C. A PCV is installed on each pump's discharge header.
D. A PCV is installed on the discharge header of the turbine-driven pump. An orifice is
installed on the discharge header of each motor-driven pump.
REF: NCRODP-26-NA
Three auxiliary feedwater pumps are provided; two are motor- driven and the third is
turbine-driven. This ensures that at least one pump is available during a complete loss
of power. The discharge header of the turbine-driven pump has an orifice which limits
the maximum flow from the pump in the event of a piping rupture downstream of the
orifice. This flow-limiting action for the motor-driven pumps is accomplished by
pressure control valves located on the pump discharge. One pump is normally
dedicated to a particular steam generator, but any pump can feed any steam generator
if required. A hand control valve (HCV) and a MOV header are provided on the
auxiliary feedwater pumps discharge for each steam generator. These headers permit
greater auxiliary feedwater diversity and reliability. Prior to joining the main feedwater
headers, a check valve in the auxiliary feedwater line prevents backflow from the steam
generators in the event of an auxiliary feedwater piping rupture.
Time:
I
Points:
1.00
Version:
0 1 2 3456789
Answer: ACAACBDBDB
Scramble Range: A - D
RO Tier:
T2GI
SRO Tier:
Key Word:
AUX FEED WATER
Cog. Level:
M 3.1/3.4
Source:
NEW
Exam:
NA02301
Test:
R
Misc:
RA/LSM/GH/SC
Tuesday, July 23, 2002 01:31:32 PM
68
71. 062A2.09 00 I/T2G2//AC CURRENT/C/A 2.7/3.0/NEW/NA02301/R/LSM/LM/GH/SC
Shutting the battery input breaker on a 120-volt AC static inverter without previously
charging the capacitors results in which one of the following?
A. Large voltage surges, breaker trip, and possible circuit damage.
Bf Large current surges, breaker trip, and possible circuit damage.
C. Large surges in both voltage and current, breaker trip, and possible circuit damage.
D. Normal operation of the breaker, the capacitors are charged after the battery input
breaker is closed.
Lesson Plan for VITAL AND EMERGENCY ELECTRICAL DISTRIBUTION SYSTEM
(35)
1.
The static inverters provide a reliable source of AC electrical power to vital
instrumentation and controls.
1.1.
Pre-charging the inverter precharges the filtering capacitors to prevent large
current surges.
2.
Shutting the breaker without previously charging the capacitors results in large current
surges, breaker over-current trip, and possible circuit damage
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: BBDADACCCA
Scramble Range: A - D
RO Tier:
T2G2
SRO Tier:
Key Word:
AC CURRENT
Cog. Level:
C/A 2.7/3.0
Source:
NEW
Exam:
NA02301
Test:
R
Misc:
LSM/LM/GH/SC
Tuesday, July 23, 2002 01:31:32 PM
69
72. 062AK3.03 001/T1 10/TIG 1/SERVICE WATER/C/A 4.0/4.2/M/NA02301/C/RA/LSM
Assume the following plant conditions:
- ECA-0.0 is in effect due to a loss of all AC power
- The operators have performed actions of the procedure to re-energize the busses
and are up to the step of checking the Service Water System
The service water pumps are started before a transition is made to a recovery
procedure, because
A' subsequent procedures will start equipment within power-source limitations, which
will place heat loads on the Service Water System.
B. this provides procedure redundancy as the pumps will always be started in
subsequent procedures.
C. a failure of the pumps to start will prevent a procedure transition.
D. the number of pumps started determines which procedure is entered.
Modified NA Bank ID: 3989
Original Question:
Unit 1 was operating at 100% power, with both unit l's service water pumps in
operation, when a total loss of off-site power occurred. The following conditions exist:
All plant equipment responded as designed with the exception of the U-1 1 H and 1 J
emergency diesel generators (EDG) which failed to start.
The operators have corrected the cause of the start failure and are preparing to start
the 1H EDG.
Following the successful start of the 1 H EDG, the unit 1 "A" service water pump will
automatically start on
A.
loss of reserve station service
B.
low service water flow
C.
1J4160V emergency bus UV
D.
"B" service water pump trip
Answer:
A
Time:
I
Points:
1.00
Version: 0 1 23456789
Answer: ABAADDDADB
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:32 PM
70
RO Tier:
TIGI
Key Word:
Source:
Test:
M
C
SRO Tier:
TIGI
Cog. Level: C/A 4.0/4.2
Exam:
NA02301
Misc:
RA/LSM
73. 062G2.1.12 001//T2G2/EDG/C/A 2..9/4.0/NEW/NA02301/S/LSM/LM/SC
One qualified circuit between the off-site transmission network and the on-site Class
1 E AC Electrical Power Distribution System has been declared inoperable. You
instruct the crew to perform 0-PT-80. The circuit that was declared inoperable fails SR
3.8.1.1 acceptance criteria.
Which one of the following is your next required action?
Af Check the remaining circuits per 0-PT-80.
B. Enter TS condition G, required action G.1 and G.2.
C. Enter TS condition I, required action II.
D. Enter TS 3.0.3.
Provide references
A. Since the Required Action only specifies "perform," a failure of SR
acceptance criteria does not result in a Required Action not met. The
must be tested.
3.8.1.1
remaining circuits
B. Only correct if this constitutes a second required circuit failure. The second offsite
circuit is inoperable, and Condition G, for two offsite circuits inoperable, is entered.
C. Only required if two EDG's are inoperable. The failure of the SR does not cause the
EDG to be inoperable.
D. Entry TS 3.0.3 is required if 3 or more sources are inoperable.
Reference TS/ TS BASIS 3.8.1
AC Sources-Operating B 3.8.1 BASES (Draft 3), 07/17/01
LCO
LCO 3.8.2, "AC Sources-Shutdown."
ACTIONS A.1
To ensure a highly reliable power source remains with one offsite circuit inoperable, it is
necessary to verify the OPERABILITY of the remaining required offsite circuit(s) on a
more frequent basis. Since the Required Action only specifies "perform," a failure of SR
Tuesday, July 23, 2002 01:31:33 PM
71
second required circuit fails SR 3.8.1.1, the second offsite circuit is inoperable, and
Condition G, for two offsite circuits inoperable, is entered.
A.2
Required Action A.2, which only applies if the train cannot be powered from an offsite
source, is intended to provide assurance that an event coincident with a single failure of
the associated EDG will not result in a complete loss of safety function of critical
redundant required features. These features are powered from the redundant AC
electrical power trains. The Completion Time for Required Action A.2 is intended to
allow the operator time to evaluate and repair any discovered inoperabilities. This
Completion Time also allows
(continued)
3.8 ELECTRICAL POWER SYSTEMS
3.8.1 AC Sources-Operating
LCO 3.8.1 The following AC electrical sources shall be OPERABLE:
a. Two qualified circuits between the offsite transmission network and the onsite Class
1 E AC Electrical Power Distribution System;
b. Two emergency diesel generators (EDGs) capable of
supplying the onsite Class 1 E power distribution
subsystem(s);
c. One qualified circuit between the offsite transmission network and the onsite Class
1 E AC Electrical Power Distribution System and one EDG capable of supplying the
onsite Class 1 E AC power distribution subsystem on the other unit for each required
shared component; and
d. Required sequencing timing relays.
A. One LCO 3.8.1 .a offsite circuit inoperable.
A.1 Perform SR 3.8.1.1 for required OPERABLE offsite circuit(s).
Tuesday, July 23, 2002 01:31:33 PM
72
74. 063K2.01 011/T2G2/T2G 1/POWER SUPPLY/M 2.9*/3.1 */M/NA02301/C/RA/GWL/LSM/SC
Which one of the following is the power supply to the Unit 1 air side seal oil back-up
pump?
A! 125-volt DC bus 1-IV.
B. "A" 480-volt AC Bus.
C. 120-volt AC vital bus 1-11.
D. "H" 480-volt AC Bus.
North Anna Lesson NCRODP-32-NA objective G of detailed descriptions.
Modified from questions # ID 183 and 119.
A. Correct, this is the power supply for the Air side seal oil back-up pump.
B. Incorrect, this the emergency bus power supply for B train AC components.
C. Incorrect, this is the power supply various vital loads.
D. Incorrect, this the emergency bus power supply for A train AC components.
Time:
I
Points:
1.00
Version:
0 1 2 34 5 6 7 8 9
Answer: ACBCCDBDBC
Scramble Range: A - D
RO Tier:
T2G2
SRO Tier:
T2G 1
Key Word:
POWER SUPPLY
Cog. Level:
M 2.9*/3.1*
Source:
M
Exam:
NA02301
Test:
C
Misc:
RA/GWL/LSM/SC
75. 064A4.01 00l/T2G2/T2G2/EDG/C/A 4.0/4.3/BANK/NA02301 /C/RA/LSM/GH
Tuesday, July 23, 2002 01:31:33 PM
The IJ emergency diesel generator (EDG) is supplying the 1J bus. The motor
operated potentiometer (MOP) has failed. Speed is being controlled manually.
If the 1J EDG trips due to an overspeed condition, which one of the following actions
must be taken to restart the 1J EDG?
A! Reset the shutdown relay in the control room and reset the fuel racks.
B. Reset the shutdown relay in the control room and return the MOP defeat switch to
AUTO.
C. Reset the fuel racks then return the MOP defeat switch to AUTO.
D. Return the MOP defeat switch to AUTO then reset the fuel racks.
73
1-OP-6.2, Rev. 23, pages 3 and
1992 bank
Time:
I
Points:
1.00
RO Tier:
Key Word:
Source:
Test:
T2G2
BANK
C
4
Version:
0 1 23456789
Answer: AADACBCCDD
Scrn
SRO Tier:
T2G2
Cog. Level:
C/A 4.0/4.3
Exam:
NA02301
Misc:
RA/LSM/GH
76. 065AA2.08 001//TI G2/IA LOSS/C/A 2.9/3.3/BANK/NA02301 /S/RA/LSM/SC
- REFERENCE
VISION OBJ. 11662, AP-28 (bank)
Bases for isolating charging
BANK 1996/01/29
KA modified on 06/05/02
Time:
I
Points:
RO Tier:
Key Word:
Source:
Test:
IA LOSS
BANK
S
1.00
Version:
0 1 234567
Answer: ABBBDABC
SRO Tier:
Cog. Level:
Exam:
Misc:
89
C A
Scramble Range: A - D
TIG2
C/A 2.9/3.3
NA02301
RA/LSM/SC
Tuesday, July 23, 2002 01:31:33 PM
amble Range: A - D
Given the following conditions:
-
Unit 1 was operating at 100% power.
-
A loss of station instrument air (IA) has occurred.
-
The unit has been tripped due to low IA pressure.
The procedure will eventually direct the closure of one of the charging line MOVs for
which one of the following reasons?
A' A loss of PRZR level control.
B. The letdown divert valve failing to the stripper.
C. The letdown pressure control valve, 1-CH-PCV-1 145, failing closed.
D. A loss of VCT makeup capability.
74
77. 065AK3.08 ooi/TriG3/TIG2/ES-0.2/C/A 3.0/3.2/M/NA02301/C/RA/LSM/SC
Unit 1 was operating at 100% power when a loss of instrument air occurred. The crew
tripped the reactor and performed 1-E-0, "Reactor Trip or Safety Injection," and
1-ES-0.1, "Reactor Trip Response."
The following conditions exist:
- All RCPs secured due to loss of component cooling water.
- Containment instrument air pressure is 0 psig.
- CRDM fans 1-HV-F-37A, E, and F are running.
- The Operations Manager has approved a natural circulation cooldown.
The crew should use which one of the following ?
A. 1-ES-0.2B, "Natural Circulation Cooldown without CRDM Fans."
B. 1-OP-3.2, "Unit Shutdown From Mode 3 to Mode 4."
C. 1-ES-0.2A, "Natural Circulation Cooldown
1-ES-0.2B, "Natural Circulation Cooldown
DW 1-ES-0.2A, "Natural Circulation Cooldown
completion.
with CRDM Fans," then transition to
without CRDM Fans," when directed.
with CRDM Fans," and perform to
Bank 84 modified format only ID: 4097
Associated objective(s):
12492
Plant Mod during
Time:
I
RO Tier:
Key Word:
Source:
Test:
TIG3
M
C
the last two outages made "D" correct answer.
Points:
1.00
Version:
0 1 23456789
Answer: DDBCACDACD
Scramble Range: A - D
SRO Tier:
TIG2
Cog. Level:
C/A 3.0/3.2
Exam:
NA02301
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:33 PM
75
78. 067G2.4.25 001/TIG1//FIRE PROTECTION/M 2.9/3.4/M/NA02301/R/RA/GWL/SC
Assume the following conditions:
- An Appendix-R fire is in progress.
- the Appendix-R key switches for the steam generator power operated relief valves
have been placed in the EMERG CLOSE position.
RCS temperature is controlled by the operator assigned to perform main steam valve
operations by which one of the following?
Locally ...
A0 controlling the steam generator power-operated relief valves using the manual
handwheel.
B. opening the main steam trip bypass valves using the manual handwheel.
C. placing the Appendix-R key switches in the NORMAL position, then returning the
switches to the EMERG CLOSE position.
D. opening the decay heat release valve.
Question replaced - system operations had changed
- A fire is in progress in the unit 1 emergency switchgear room.
- Halon has been discharged into the area.
- No other manual actions have taken place in the emergency switchgear room.
- An SI has resulted in the dumping of the control room air bottles into the emergency
switchgear room.
North Anna Bank Question #678
Associated objective 5781.
A. Incorrect, Emergency switchgear room recirculation fans have not tripped.
B. Incorrect, with the fire dampers being closed the control room will not pressurize.
C. Incorrect, the control room pressurization is affected, it will not pressurize because of
the fire
dampers being closed.
D. Correct, with the fire dampers being closed the control room will not pressurize.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ABDACDDBBD
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
Key Word:
FIRE PROTECTION
Cog. Level:
M 2.9/3.4
Source:
M
Exam:
NA02301
Test:
R
Misc:
RA/GWL/SC
Tuesday, July 23, 2002 01:31:33 PM
76
79. 067G2.4.29 001//TI1GI/EPIP/M 2.6/4.0/NEW/NA02301/S/RA/LSM/SC
You are the US. You are informed that there has been an accident involving a
company truck colliding with a reserve station service transformer (RSST). A small fire
was involved, but was quickly extinguished by the truck driver using a portable fire
extinguisher located in the truck (six minutes). The RSST has failed resulting in a
partial loss of off-site power. The EDG and all the associated equipment responded
normally.
Which one of the following describes your required response?
Af EPIP-1.01 must be initiated because safety-related equipment was affected by the
fire.
B. EPIP-1.01 must be initiated because the fire was extinguished without assembling
the fire brigade.
C. EPIP-1.01 is not initiated because although safety-related equipment was affected,
the fire duration was less than 10 minutes.
D. The fire caused the activation of safety-related equipment, EPIP-1.01 must be
entered.
EPIP-1.01 must be initiated if either of the following conditions
(0-FCA-0).
occur during a fire
Safety-related equipment is affected by the fire
Fire duration is greater than ten minutes
KA modified on
Time:
I
RO Tier:
Key Word:
Source:
Test:
NEW
S
06/05/02
Points:
1.00
Version:
0 1 23456789
Answer: ABDCDCDDAA
SRO Tier:
TIGI
Scramble Range: A - D
Cog. Level:
M 2.6/4.0
Exam:
NA02301
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:33 PM
77
80. 068A3.02 001/T2GI /T2G 1/RADWASTE/C/A 3.2/3.5/NEW/NA02301/C/RA/LSM
Which one of the following describes how liquid waste effluent control valve
PCV-LW-1 15 operates?
A! Fails shut on loss of air and fails shut on loss of electric power.
B. Fails shut on loss of air and fails as-is on loss of electric power.
C. Automatically closes on high effluent flow rate and fails shut on loss of air.
D. Fails shut on high effluent flow rate.
NCRODP-92.3-LP.1, Revision 4, Page 22
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ADCDDBBDCB
Scramble Range: A - D
RO Tier:
T2G1
SRO Tier:
T2G I
Key Word:
RADWASTE
Cog. Level:
C/A 3.2/3.5
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM
81. 068AK2.03 001/TIG1/T1G1/AUX SHUTDOWN/C/A 2.9/3.1/BANK/NA02301/C/RA/LSM/SC
Given the following plant conditions:
- Unit 1 was at 100% power when noxious fumes forced evacuation of the MCR.
-The immediate actions of 1-AP-20, Operation from the Auxiliary Shutdown Panel,
were completed prior to evacuation.
-AFW flow was throttled to 150 GPM to each SG prior to evacuation.
Which one of the following describes the sequence of control manipulations required to
transfer control of "C" SG AFW flow?
A. Decrease the demand on 1-FW-HCV-1 00C controller, then place the
LOCAL-REMOTE switch in LOCAL.
B. Place the LOCAL-REMOTE switch in LOCAL, then decrease the demand on the
controller.
C. Place the LOCAL-REMOTE switch in LOCAL, then throttle 1-FW-MOV-1 00C.
D. Locally throttle 1-FW-MOV-100C, then place the LOCAL-REMOTE switch in
LOCAL.
Tuesday, July 23, 2002 01:31:33 PM
78
Bank - Supplied by Utility for this examination.
Orginal Question - replaced. While this question was used on the 1992 exam, it's
contents are no longer considered required operator knowledge.
LCV-1460 A and B, Letdown Isolation Valves, do not have "Local/Remote" switches at
the auxiliary shutdown panel.
Which one of the following describes the reason?
HCV-1 200 A, B, and C provide sufficient letdown isolation alone.
LCV-1460 A and B can be controlled from the Appendix R isolation panel.
LCV-1460 A and B cannot be operated without HCV-1200A, B and C being closed.
There is no need to operate LCV-1460A and B after Control Room Evacuation.
NCRODP-88.3-LP.1, Objective B
1993 bank
Time:
I
Points:
1.00
Version: 0
Answer: A
RO Tier:
Key Word:
Source:
Test:
TIGI
AUX SHUTDOWN
BANK
C
123456789
ABCACCACB
SRO Tier:
TIG
Cog. Level:
C/A
Exam:
NA(
Misc:
RA/
Scr:
31
.2.9/3.1
02301
LSM/SC
amble Range: A - D
82. 071 A4.24 001/T2GI/T2G1/WASTE GAS/M 2.9/3.4/NEW/NA02301/C/RA/LSM/SC
The "A" waste gas decay tank (WGDT) has been sampled and release paperwork has
been delivered to the control room by Health Physics.
Which one of the following correctly describes the personnel involvement in the control
room prior to releasing the WGDT?
A. Any backboards-qualified operator can release the tank and a licensed reactor
operator must be made aware of the release.
B. Only a licensed reactor operator can release the tank and a licensed senior reactor
operator must be made aware of the release.
Cf A licensed reactor operator or license class trainee can release the tank and a
licensed senior reactor operator must be made aware of the release.
D. A license class trainee can release the tank and a licensed reactor operator must
be made aware of the release.
Tuesday, July 23, 2002 01:31:34 PM
79
Source - new - written by licensee for this exam.
Question replaced - based on interpretation of K/A and task was normally performed by
Which one of the following describes the controls used for Waste Gas Decay Tank
releases?
The Waste Decay Tank is sampled:
and assessed independently to verify compliance with release limits.
and assessed independently for noble gases, radioiodines, particulates, and tritium.
to ensure the 30 day dose commitment estimate is not exceed and to verify compliance
with release limits.
to ensure the 30 day dose commitment estimate is not exceed and to verify compliance
with 10CFR part 20 limits.
Reference:
Ncrodp-45
The actual source term through the Process Vent System is sampled routinely. Dose
calculations are made to ensure that actual releases are within the limits established for
this release pathway. Concurrently, dose projections are made to estimate the dose
commitment for the next 30 day period. The dose projection provides a degree of
assurance that continued operation will not exceed any release limit. In addition to
these normal release considerations, specific releases such as a Waste Gas Decay
Tank are sampled and assessed independently to verify compliance. The Process
Vent System is routinely sampled for noble gases, radioiodines, particulates, and
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CBBCDBACCD
Scramble Range: A - D
RO Tier:
T2G I
SRO Tier:
T2G1
Key Word:
WASTE GAS
Cog. Level:
M 2.9/3.4
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:34 PM
80
83.072A1.01 00I/T2GI1T2GI/RAD MONITOR/M 3.4/3.6/NEW/NA02301/C/RA/LSM
Reference:
NCRODP-46
Victoreen Radiation Monitoring Subsystem. Each Containment is equipped with two
Seismic class I (earthquake-proof) monitor units (see Table 46-4). Each unit consists
of a high range detector (100 to 107 R/hour), a control room readout unit, a recorder,
and interconnecting cable. The detectors are located approximately 155 degrees apart
for Unit 1 and approximately 130o apart for Unit 2 on the inside of the containment
polar crane wall to provide physical separation. Their location approximately 5 feet
above the operating floor facilitates the periodic calibration of the detectors. The units
are designed for intense radiation fields, such as might exist after an accident, and are
powered from diverse vital buses. Their indicators and racks in the MCR also meet
separation and seismic requirements. The high range containment radiation monitors
are for indication/verification purposes only and do not affect the logic schemes of any
safety-related plant systems.
Nuclear Research Corporation (NRC) Radiation Monitoring Subsystem. The
NRC high range monitors are located on potential effluent lines that were either not
provided with Westinghouse monitors or lacked high range monitors. The NRC high
range monitors (listed in Table 46-5) were installed prior to the Kaman monitors. (This
is mentioned because there are some redundant monitors between the two
subsystems.) These monitors measure the gaseous effluent release paths of the
Process Vent Subsystem of the Gaseous Waste System, ventilation vent stacks "A"
and "B", and potential effluent paths of contaminated steam (in the event of a
primary-to-secondary leak in the steam generators.) The potential paths of
contaminated steam monitored are the six main steam lines and the exhausts from the
two turbine-driven auxiliary feed pumps.
The high range effluent monitors consist of a detector and the control unit. The
detector has an 9-decade range of 10-5 to 10+4 R/hr which is displayed on an 8-
Tuesday, July 23, 2002 01:31:34 PM
After a seismic event, which one of the following high-range containment radiation
monitors are for indication/verification purposes ONLY and do not affect the logic
schemes of any safety-related plant systems?
A. Merlin-Gerin Radiation Monitoring Subsystem.
B. Kaman Radiation Monitoring Subsystem.
Cf Victoreen Radiation Monitoring Subsystem.
D. Nuclear Research Corporation Radiation Monitoring Subsystem.
81
decade display of 10-4 to 10+4 and is comprised of two G-M tubes, an ion chamber,
and an internal cesium check source. The components are enclosed in a box that
protects them from expected operating environments. The detector is enclosed in a
lead shield to reduce background radiation.
Kaman Radiation Monitoring Subsystem. The high range monitors in this
subsystem are supplemented by normal range monitors for verification purposes. The
Kaman monitors are listed in Table 46-6. These monitors measure the gaseous
effluent release paths of the process vent (a subsystem of the Gaseous Waste
System), and ventilation vent stacks "A" and "B". These monitors operate in
conjunction with the Westinghouse monitors for the same release paths. They have a
greater sensitivity and range than the Westinghouse monitors for these release paths.
They can monitor beta/gamma activity from 10-7 to 105 microcurie per cubic centimeter
and iodine/particulate releases below 100 microcurie per cubic centimeter. They are
redundant also with the NRC monitors. (The NRC monitors were originally intended to
be a short term solution to NUREG 0578, but have been left in place as backup
monitors.)
The normal range monitors consist of a cabinet assembly, a pumping system
with automatic flow control, a gas sampler assembly with a beta detector and check
source, two particulate-iodine collectors without detectors, and an associated
microcomputer. The high range monitors consist of a cabinet assembly, a pumping
system with automatic flow control, a gas sampler assembly with two G-M tubes and a
check source, and three particulate-iodine collector assemblies with G-M tube
detectors.
The process vent normal range monitor from Table 46-6, GW-RM-1 78-1, has the
same automatic functions as those mentioned previously for Westinghouse process
vent monitors GW-RM-101 and -102. A high radiation level sensed by GW-RM-178-1
causes the flow control valve GW-FCV-101 from the waste gas decay tanks to shut, the
containment vacuum pumps to trip, and the vacuum pumps' discharge valves to shut.
Merlin-Gerin Radiation Monitoring Subsystem. The Merlin-Gerin radiation
monitoring subsystem consists of the eight N-16 radiation monitors (1-MS-RM-190,
191,192, and 193 and 2-MS-RM-290, 291, 292, and 293). These radiation monitors
are used to monitor the main steam lines for indication of a Steam Generator tube leak
or rupture. The monitors provide the operators with an indication in the Control Room
of Steam Generator leaks as small as 1 gallon per day (GPD). The Merlin-Gerin
subsystem also is installed in the discharge line of the High Capacity Steam Generator
Blowdown System. These monitors, 1-SS-RM-125 and 2-SS-RM-225, monitors the
blowdown effluent prior to discharge to the Circulating Water tunnel and subsequent
discharge to the environment. Radiation monitor 1-SS-RM-125 is located in the
Turbine Building basement adjacent to Blowdown Cooler 1-BD-E-2AIB. The monitor
has a local indicator and provides a signal to the Blowdown System control panel
1-EI-CP-10. A high radiation alarm will be annunciated in the Control Room by a
Tuesday, July 23, 2002 01:31:34 PM
82
Steam Generator Blowdown Trouble alarm. The Blowdown radiation monitor has a
1OE-07 to 1OE-03 pCi/cc range. The Merlin-Gerin radiation monitors are listed in Table
46-11.
All Rad Monitor Alarm Setpoints are maintained in the "Rad Monitor Setpoint Records"
book in the MCR.
Tuesday, July 23, 2002 01:31:34 PM83
83
MODIFIED BANK 3088
Original Question:
Assume the following conditions.
Unit 1 is in mode 6
Core off-load is in progress
A fuel handling accident has occurred in the fuel building
A high and a high-high alarm was received on 1-RM-RMS-1 53.
This alarm will isolate main control room ventilation,
A.
dump bottled air, and start the unit -1 unit 41 and 42 fans only
B.
dump bottled air, and start both units' 41 and 42 fans
C.
and start all 41 and 42 fans, but will not dump bottled air
D.
and dump bottled air, but will not start any 41 or 42 fan
Answer:
B
Time:
I
Points:
1.00
Version:
0 1 2 34 5 67 89
Answer: BDADBDCBAB
Scramble Range: A - D
RO Tier:
T2G1
SRO Tier:
Key Word:
3.1/3.5
Cog. Level:
M 3.1/3.5
Source:
BANK
Exam:
NA02301
Test:
R
Misc:
RA/LSM/SC
85. 073A1.01 001/T2G2/T2G2/RAD MONITOR/M 3.2/3.5/M/NA02301/C/LSM!LM/LSM/SC
Which one of the following describes the result of a hi-hi alarm actuation on the
Westinghouse clarifier outlet process monitor (RM-1 11)?
A. Only clarifier inlet valve FCV-LW-100 closes, which causes the steam generator
blowdown pumps to trip. The clarifier outlet PCV-LW-1 15 does not close.
B. The actuation causes clarifier outlet valve PCV-LW-1 15 to close and clarifier inlet
FCV-LW-100 to close. The steam generator blowdown pumps trip when the inlet
valve closes.
C. The actuation causes clarifier inlet valve FCV-LW-1 00 to close and the steam
generator blowdown pumps to trip. The clarifier outlet PCV-LW-1 15 does not close.
D. Clarifier outlet valve PCV-LW-1 15 closes, which causes clarifier inlet valve
FCV-LW-100 to close, which in turn causes the steam generator blowdown pumps
to trip.
Tuesday, July 23, 2002 01:31:34 PM
84
Bank 1091
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BDBAACCBCD
Scramble
RO Tier:
T2G2
SRO Tier:
T2G2
Key Word:
RAD MONITOR
Cog. Level:
M 3.2/3.5
Source:
M
Exam:
NA02301
Test:
C
Misc:
LSM/LM/LSM/SC
86. 075G2.1.27 00I/T2G2/T2G2/CIRC WATER/M 2.8/2.9/M/NA02301/C/RA/LSM
Range: A - D
Which one of the following conditions will cause the unit-1 "A" Circulating Water
System's screenwash pump (1-CW-P-2A) to start automatically when its control switch
is in the AUTO position?
A. Rotation of any travelling water screen for any reason.
B. Screenwash header pressure decreases below 65 psig.
C. Bearing Lube System PCV is fully closed.
D' Bearing lube pressure < 25 psig.
Bank - ID: 854
Associated objective(s):
7447
List the following information associated with the circulating water screenwash pumps.
Functions which can be performed by each pump
Conditions which will start each screenwash pump manually
Conditions which will start each screenwash pump automatically
Time:
I
Points:
1.00
Version:
0 1 2345 67 89
Answer: DADCCCADBC
Scramble Range: A - D
RO Tier:
T2G2
SRO Tier:
T2G2
Key Word:
CIRC WATER
Cog. Level:
M 2.8/2.9
Source:
M
Exam:
NA02301
Test:
C
Misc:
RA/LSM
Tuesday, July 23, 2002 01:31:34 PM
85
87. 076AA 1.04 001/TI
1 /TIG 1/RCS ACTIVITY/M 3.2/3.4/NEW/NA02301/C/RA/LSM/GH
Replaced question - based on expected operator knowledge
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ADBCBDBACD
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
TIGI
Key Word:
RCS ACTIVITY
Cog. Level:
M 3.2/3.4
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/GH
88. 079K1.01 001I/T2G2/T2G2/AIR SYSTEMS/M 3.9/3.1/NEW/NA02301/C/LSM/LM/SC
Which one of the following describes the interconnection of the service air and
instrument air systems?
A. the service air receivers are the backup air supply for the instrument air receivers.
B.0 the service air receivers normally supply air to the instrument air receivers.
C. the instrument air receivers normally supply air to the service air receivers.
D. the instrument air receivers are the backup air supply for the service air receivers.
Tuesday, July 23, 2002 01:31:34 PM
Unit 1 is operating at 100% power.
- The letdown radiation monitor is in HIGH alarm.
- You request Chemistry to confirm results.
- Chemistry reports the dose equivalent Iodine is 50 microcuries/gram
Which one of the following should you do?
Af Consult with Health Physics and Chemistry to determine if a change in letdown flow
is desired.
B. This indicates 1% failed fuel, trip the reactor and enter 1-E-0.
C. This indicates 1% failed fuel, isolate letdown.
D. Request chemistry to take a second sample, declare the monitor inoperable.
86
Module NCRODP17
At one time, the Service Air Receivers served as the "backup" air supply for the
Instrument Air Receivers. This was accomplished by utilizing cross connect piping
between both Service Air Receivers and both Instrument Air Receivers. This cross
connect piping has four installed Pressure Control Valves and four associated check
valves. On decreasing Instrument Air Pressure, the Pressure Control Valves use to
automatically open at a predetermined set point to allow the Service Air Receivers to
makeup for pressure losses in the Instrument Air Receivers. The check valves
associated with the Pressure Control Valves prevent flow reversals from the Instrument
Air Receivers to the Service Air Receivers. Therefore, the Instrument Air Receivers will
not depressurize if the Service Air Receivers lose pressure. In order to enhance the
overall reliability of the Instrument Air Subsystem, the four Pressure Control Valves
have been failed open by disconnecting their Instrument Air supply lines. As such, the
Service Air Receivers have become the "normal" air supply for the Instrument Air
Receivers as opposed to the "backup" air supply that was originally intended.
Time:
I
RO Tier:
Key Word:
Source:
Test:
T2G2
Points:
1.00
Version: 0 1 234567 89
Answer: BDBAADDBDD
SRO Tier:
T2G2
AIR SYSTEMS
NEW
C
Cog. Level:
Exam:
Misc:
Scramble Range: A - D
M 3.9/3.1
NA02301
LSM/LM/SC
89. 086A2.01 00I/T2G2/T2G2/FIRE PROTECTION/M 2.9/3.I/NEW/NA02301/C/LSM/LM/SC
Lesson Plan - Fire
and Procedures
Protection System - Fire Protection System-construction, Operation
Tuesday, July 23, 2002 01:31:35 PM
Unit 1 receives the following alarm:
- 1D-C6, MOTOR FIRE PP RUNNING
A few moments later you receive a telephone call and are told that the pump was
inadvertently started by an instrument technician during a surveillance. Which one of
the following describes how you would secure the pump?
Af The pump can be secured from the intake structure ONLY.
B. The pump can be secured from the service water pump house ONLY.
C. The pump can be secured from the unit I benchboard ONLY.
D. The pump can be secured from both the unit 1 benchboard or at the service water
pump house.
87
4.
The motor driven fire pump can be started at the unit one main control
board or in the motor driven fire pump house at the intake structure.
a.
The pump can only be stopped at the intake structure.
5.
Indications available to the control room operator that a pump has started
a.
Control room annunciator 1D-C6, MOTOR FIRE PP RUNNING.
6.
The rated discharge flow of the motor driven fire pump is 2500 gpm.
7.
The relief valve setpoint for the motor driven fire pump is 164 psig.
EE.
Diesel?driven fire pump 1?FP?P?2. [6633]
1.
The diesel driven fire pump 1-FP-P-2 takes a suction from unit one "A"
service water bay.
2.
Conditions that will cause the pump to start or trip automatically
a.
The diesel-driven pump starts in the AUTO mode if there is a loss
of AC control power or main fire loop pressure drops to 52 psig as sensed by
PS-FP-1 203 provided the local (AUTO-OFF-MANUAL A- MANUAL B- TEST) switch in
the AUTO position.
b.
The diesel-driven fire pump automatically stops on overspeed
(approx. 1900 rpm) or low oil pressure (12 psig).
3.
Manual start and stop
a.
The diesel-driven fire pump can be started from the main control room unit 1
benchboard by placing the (ON, AUTO) switch in the ON position.
b.
From the service water pump house the pump can be manually started using
either of the following methods.
(1)
By placing the local test control switch in either MANUAL A or MANUAL B and
depressing the START pushbutton.
(2)
The pump can also be manually started by placing the local
(AUTO-OFF-MANUAL A- MANUAL B- TEST) switch in the TEST position.
c.
The pump can be secured from the service water pump house ONLY.
Tuesday, July 23, 2002 01:31:35 PM
88
(1)
Depressing the local STOP pushbutton (normal method)
(2)
Placing the local (AUTO-OFF-MANUAL A- MANUAL B- TEST) switch in the OFF
position
Tuesday, July 23, 2002 01:31:35 PM89
89
91. 103A3.01 00 I/T2G3/T2G2/PHASE A/M 3.9/4.2/NEWiNA02301 /C/RA/LSM/SC
A large-break LOCA has occurred. Which one of the following is a result of a Phase A
actuation?
A. Both instrument air 1-IA-TV-102A and RHR CC return 1-CC-TlV-103A close.
B. Both blowdown trip valve 1-BD-TV-1OOF and instrument air 1-IA-IV-1 02A open.
C.f Both letdown trip valve 1-CH-fV-1204B and blowdown trip valve 1-BD-TV-100F
close.
D. Blowdown trip valve 1-BD-TV-100F closes and instrument air 1-IA-TV-1 02A opens.
Replaced a KA that did not apply to North Anna
Question replaced to provide a question that matches Operator expected memory level
knowledge.
KA modified on 06/05/02
T
RO Tier:
Key Word
Source:
Test:
92. G2.1.1 00
rime:
I
Points:
1.00
Version:
0 1 23456789
Answer: CBADBBDDCD
Scr
T2G3
SRO Tier:
T2G2
d: PHASE A
Cog. Level:
M 3.9/4.2
NEW
Exam:
NA02301
C
Misc:
RA/LSM/SC
I/T3/T3/STANDING ORDER/C/A 3.7/3.8/NEW/NA02301/C/RA/LSM
amble Range: A - D
Tuesday, July 23, 2002 01:31:35 PM
When pumping the gas stripper, it is permissible to pump to a lower than normal level
in order to minimize the number of times that the stripper must be pumped. Which
one of the following allows this to occur?
A' Standing order 215, Pumping of Radioactive Fluids to the Boron Recovery Tanks.
B. The NPDES release permit.
C. Engineering Transmittal SE-97-119, but must be approved by the Operations
Manager or designee.
D. Engineering Transmittal SE-97-119, but must be approved by the Operations
Manager and may not be delegated.
90
Reference -
NEW
North Anna Power Station
Standing Order No. 215, Rev 3
I.
TITLE:
Pumping of radioactive fluids to the Boron Recovery Tanks
I1.
BACKGROUND:
Deviation Report N-96-1770 was written on September 11, 1996 documenting the
unplanned radioactive release while filling the "C" Boron Recovery Tank, 1-BR-TK-4C.
The fill rate was approximately 30 gallons per minute which exceeded the capacity of
the Process Vent sweep. This produced flow through the BRT vent into the Waste
Solids Building. The Waste Solids Building is not a monitored release path within the
NAPS license.
Task assignment MCT 96-0226 was initiated to coordinate a test of the BRT vent flow
as created by the process vent system. Testing of the vent inlet flow was attempted
using a differential pressure measurement across the roof vent of the boron recovery
tanks. The differential pressure was too low to be measured on a manometer that has
graduations of 0.1 inch (water). The calculated vent flow velocity of 1 foot/second is
too low to be measured with a rotameter(REA 97-065 had been written to install throttle
valves and rotometers in the vent lines from the three BRTs for utilization during filling
operations). Other solutions are being sought for final resolution in accordance with
MCT 96-0226.
Engineering Transmittal SE-97-119, Rev. 0 summarized the measurement of sweep
gas flow rate from the boron recovery tanks to the process vent. The ET provides
guidance to Design Engineering for use in developing DCP 97-110 to add isolation
valves as well as liquid and gas flow measuring devices to properly monitor BRT filling
activities. Without the addition of these isolation valves to ensure that all sweep gas is
drawn from the on-service BRT while filling, the maximum allowable fill rate for a BRT is
5 gpm. After the DCP is completed and installed, and the OP's are properly revised,
the maximum allowable fill rate will increase to 30 gpm.
Ill.
INSTRUCTIONS:
A Miscellaneous Gas Release Permit must be completed prior to pumping from any
Source to the Boron Recovery Tanks. When pumping the Gas Stripper, it is permisible
To pump to a lower than normal level in order to minimize the number of times that the
Stripper must be pumped.
Tuesday, July 23, 2002 01:31:35 PM
91
Time:
I
RO Tier:
T3
Points:
1.00
Version:
0 1 23456789
Answer: ADCCCBDCCA
SRO Tier:
T3
Scramble Range: A - D
Key Word:
STANDING ORDER
Source:
NEW
Test:
C
Cog. Level:
Exam:
Misc:
C/A 3.7/3.8
NA02301
RA/LSM
93. G2.1.10 00I//T3/QPTR AFD/C/A 2.7/3.9/NEW/NA02301/S/RA/LSM/SC
The unit is being maintained within the boundaries of the following ITS LCOs:
- Shutdown bank and control bank insertion limits
- Rod group alignment limits
- Axial flux difference
- Quadrant power tilt ratio
Which one of the following is ensured?
A' The core operates within the fuel design criteria.
B. There are no fuel cladding failures in the event of a LOCA, loss
or other accident requiring termination by an RPS trip function.
C. There are no fuel cladding failures in the event of a LOCA, loss
or other accident requiring termination by an ECCS initiation.
of flow, ejected rod,
of flow, ejected rod,
D. There are no fuel cladding failures in the event of a LOCA, loss of flow, ejected rod,
or other accident requiring termination by an RPS trip function or an ECCS
initiation.
Tuesday, July 23, 2002 01:31:35 PM
92
B, C, and D are incorrect because this will not prevent cladding damage, it will ONLY
minimize it.
Reference:
North Anna Units 1 and 2 B 3.1.6-2 Rev 4 (Draft 1), 06/19/01 Control Bank Insertion
Limits
B 3.1.6
The control banks are used for precise reactivity control of the reactor. The positions of
the control banks are normally controlled automatically by the Rod Control System, but
can also be manually controlled. They are capable of adding reactivity very quickly
(compared to borating or diluting).
The power density at any point in the core must be limited, so that the fuel design
criteria are maintained. Together, LCO 3.1.4, LCO 3.1.5, "Shutdown Bank Insertion
Limits," LCO 3.1.6, LCO 3.2.3, "AXIAL FLUX DIFFERENCE (AFD)," and LCO 3.2.4,
"QUADRANT POWER TILT RATIO (QPTR)," provide limits on control component
operation and on monitored process variables, which ensure that the core operates
within the fuel design criteria.
The shutdown and control bank insertion and alignment limits, AFD, and QPTR are
process variables that together characterize and control the three dimensional power
distribution of the reactor core. Additionally, the control bank insertion limits control the
reactivity that could be added in the event of a rod ejection accident, and the shutdown
and control bank insertion limits ensure the required SDM is maintained.
Operation within the subject LCO limits will limit fuel cladding failures that would breach
the primary fission product barrier and release fission products to the reactor coolant to
within acceptable limits in the event of a loss of coolant accident (LOCA), loss of flow,
ejected rod, or other accident requiring termination by a Reactor Trip System (RTS) trip
function.
APPLICABLE SAFETY ANALYSES
The shutdown and control bank insertion limits, AFD, and QPTR LCOs are required to
maintain power distributions that limit fuel cladding failures to within acceptable limits in
the event of a LOCA, loss of flow, ejected rod, or other accident requiring termination
by an RTS trip function.
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: ABBCABBACB
Scramble Range: A - D
RO Tier:
SRO Tier:
T3
Key Word:
QPTR AFD
Cog. Level:
C/A 2.7/3.9
Source:
NEW
Exam:
NA02301
Test:
S
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:35 PM
93
94. G2.1.12 001//T3/TS/C/A 2.9/4.0/NEW/NA02301/S/RA/LSM/SC
Unit 1 is operating at 97% power.
At 0300, you were informed that QPTR is 1.04.
It is now 0400. Which one of the following is the highest power level the ITS will allow
for this condition?
Af 97%
B. 94%
C. 91%
D. 84%
Provide references.
A. This is not a 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> LCO, no power change is required for two hours.
B. Reflects 3% change (step change for each 1% RTP)
C. Reflects 6% change (half of change required at 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br />)
D. Reflects required change in two hours.
Reference:
(New SRO ONLY)
3.2.4-1 Rev 4 (Draft 1), 06/19/01
3.2 POWER DISTRIBUTION LIMITS
3.2.4 QUADRANT POWER TILT RATIO (QPTR)
LCO 3.2.4 The QPTR shall be # 1.02.
MODE 1 with THERMAL POWER > 50% RTP.
TS Required ACTIONS
A. QPTR not within limit.
A.1 Reduce THERMAL POWER 3% from RTP for each 1% of QPTR > 1.00. Within 2
hours
KA modified on 06/05/02
Tuesday, July 23, 2002 01:31:35 PM
94
Time:
I
RO Tier:
Key Word:
TS
Source:
NEW
Test:
S
Points:
1.00
Version:
0 1 23456789
Answer: ADCCADBCDB
SRO Tier:
T3
Cog. Level:
C/A
Exam:
NA(
Misc:
RA/
Scramble Range: A - D
2.9/4.0
12301
LSM/SC
95. G2.1.29 001/T3/T3/3.4/3.3/M 3.4/3.3/BANKINA02301/C/RA/LSM
Assume the following conditions:
- Unit 1 is in mode 5 following a refueling outage.
- Startup of secondary systems is in progress.
- The annex supervisor assigns you to perform a valve lineup on the Main
Feedwater System.
- You are an operator who is currently working on step 3 of the development program.
You should do which one of the following?
A0 Inform the annex supervisor that you are not qualified to perform any tasks on the
Main Feedwater System.
B. Perform the valve lineup only if you have completed all job performance measures
on the Main Feedwater System.
C. Inform the annex supervisor that you are qualified to perform only those tasks in
step 3 for which you have completed job performance measures.
D. Perform the valve lineup, but notify the annex supervisor that it will have to be
independently verified.
Bank 39
ID: 3224
Time:
I
RO Tier:
Key Word:
Source:
Test:
T3
3.4/3.3
BANK
C
Points:
1.00
Version:
0 1 23456789
Answer: ADCCDCBDDD
SRO Tier:
T3
Cog. Level:
Exam:
Misc:
Scramble Range: A - D
M 3.4/3.3
NA02301
RA/LSM
Tuesday, July 23, 2002 01:31:35 PM
95
96. G2.2.11 OO0/T3/T3/CONT. ENTRY/M 2.5/3.4/NEW/NA02301/C/RA/LSM/SC
a. correct - The use of SCBA is required if Containment pressure is greater than or
equal to 9.0 psia and less than 12.0 psia. SCBA with 33 to 37 percent oxygen volume
shall be used.
b, c, d these requirements are listed as those that can be waived in
source - NEW VPAP-01 06 1.6a. Objective
Reference:
Topic 1.6: Subatmospheric Containment Entry (VPAP-01 06) 13547
1.6a. Objective
List the following information associated with subatmospheric containment entry
(VPAP-0106).
Definition of subatmospheric containment
Physical conditions limiting the authorization of individuals for entry into
containment that may not be waived
Conditions limiting the authorization of individuals for entry into containment that
may be waived by the individual
Minimum and maximum number of members of which the entry team shall
consist
Conditions that require the containment to be evacuated
1.6b. Content
Tuesday, July 23, 2002 01:31:36 PM
96
Unit 1 is at 100% power. A team of three people plan to enter containment to
troubleshoot a failed letdown trip valve.
Which one of the following can an individual team member NOT waive prior to entry?
A! The use of SCBA for a short duration entry.
B. Two hours rest since last containment entry.
C. Working in containment twice during the previous 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br />.
D. At least six hours of rest during the previous 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />.
1.
Definition of subatmospheric containment
1.1.
Air Pressure less than or equal to 12.0 psia.
2.
Physical conditions limiting the authorization of individuals for entry into
containment that may not be waived
2.1.
Containment Entry Team personnel shall not have:
2.2.
Obvious or known respiratory difficulties (e.g., could, flu, sinusitis)
2.3.
Respiratory or cardiovascular ailments or be under a physician's care for those
ailments
3.
Conditions limiting the authorization of individuals for entry into containment that
may be waived by the individual.
NOTE: The following items may be waived by the Containment Entry Team members.
3.1.
Worked at the Station for less than 10 continuous hours immediately before
entry
3.2.
At least six hours of rest in the previous 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />
3.3.
More than two hours of light duties since the last exit from Containment
3.4.
Not worked twice in containment in the previous 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br />
4.
Minimum and maximum number of members of which the entry team shall
consist
4.1.
The smallest Containment Entry Team shall consist of two members, one of
which shall be a HP Technician.
4.2.
The largest Containment Entry Team shall consist of 15 members
4.3.
One member shall be the Containment Entry Team Leader.
5.
Conditions that require the containment to be evacuated The Containment shall
be evacuated if:
5.1.
The containment evacuation alarm, Station emergency alarm, or high flux at
shutdown alarm sounds
5.2.
Containment evacuation is announced over the Gai-tronics system
Tuesday, July 23, 2002 01:31:36 PM
97
97. G2.2.13 0O1/T3/T3/VALVE/M 3.6/.38/M/NA02301/C/RA/LSMIGH/SC
Assume the following conditions:
- Unit 1 is at 100% power.
- 1-CH-P-1C is tagged out.
- Preventive maintenance was performed on "C" charging pump suction valve
1 -CH-MOV-1270A.
- An electrician is prepared to obtain test data on the valve.
The valve must be returned to mid-position in accordance with the maintenance
procedure. Which one of the following can perform this task?
A. Operations department personnel are the only personnel authorized to operate the
valve. Any operator qualified for the task may operate this valve.
B. Only an operator with an active license may operate this valve.
C. Only an operator with an active license, or an operator in training under the direct
supervision of an operator with an active license may operate this valve.
D. The electrician may manually operate the valve.
Source: Bank ID: modified - 3222
distractor analysis:
A, B and C. This valve is part of maintenance and may be operated by Maintenance
Department personnel.
D. Correct answer per VPAP 1401 section 6.1.7 a.3
Associated objective(s):
13558
Explain the operating policy associated with the following activities (VPAP-1401).
Station component operation (SOER-94-2)
Station valve operation
Control room notification
Switchyard activities
Tuesday, July 23, 2002 01:31:36 PM98
98
Availability of safety systems (SOER-98-1)
DOMINION VPAP-1401 REVISION 10
PAGE 13 OF 35
6.1.7 Station Valve Operations [Commitment 3.2.3]
a. Operations Department personnel shall be the only Station personnel authorized to
manipulate valves except:
1. Instrument valves (e.g., local isolation valves, equalizing valves, and vents and
drains) may be operated by qualified Instrument Technicians. Instrument valves
are normally downstream of a root valve and are used to isolate an instrument.
If an instrument has only one valve for isolation, that valve shall be used as an
instrument valve.
2. Sample valves may be operated by qualified Chemistry and Radiological
Control Technicians.
3. Motor Operated Valves (MOVs) that require testing as part of a Maintenance
Procedure may be operated by Maintenance Department personnel.
4. Valves that require testing as part of an Engineering Work Request (EWR) or
Design Change Package (DCP) may be operated by Testing personnel.
5. Fire Protection valves may be operated by Safety and Loss Prevention
personnel with the concurrence of the Operations Shift Supervisor.
6. Valves that are used to control a process (not related to plant operations) may
be operated by individuals responsible for that process, as determined by
Operations management.
b. Valve operation shall be in accordance with approved Station procedures, skill of
the craft, or if action is required to protect Station equipment or personnel.
c. A procedure or process that directs operation of a valve shall include sufficient Shift
Supervisor notification.
d. Valves that have Danger Tags attached to them shall not be operated.
Tuesday, July 23, 2002 01:31:36 PM
99
98. G2.2.2 001/T3/T3/CONTROLS/C/A 4.0/3.5/NEW/NA0230 I /C/RA/LSM/SC
Unit 2 is at 74% reactor power. Severe thunderstorms are in the area and the unit trips
for no apparent reason. The crew enters 2-E-0.
- The reactor was verified tripped.
- The turbine trip buttons were manually depressed.
- Turbine stop valves failed to close.
Which one of the following describes your next two immediate actions?
A. Put both EHC pumps in pull to lock, then reset reheaters.
B. Put both EHC pumps in pull to lock, then verify generator output breaker open.
C. Manually run back turbine, then put both EHC pumps in pull to lock.
D/ Put both EHC pumps in pull to lock, then manually run back turbine.
reference - 1-E-0 rev 27 page 2 of 22
a. Put Both EHC pumps in pull to lock, the turbine is not tripped so turbine must be run
back
b. generator output breakers are after first two steps
c turbine is runback only if Put Both EHC pumps in pull to lock fails to close turbine
stop valves. Stem states assume no other failures
d. Correct answer
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: DABAADBCBD
Scramble Range: A - D
RO Tier:
T3
SRO Tier:
T3
Key Word:
CONTROLS
Cog. Level: C/A 4.0/3.5
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
Tuesday, July 23, 2002 01:31:36 PM
100
99. G2.2.26 001//T3/REFUELING/M 2.5/3.7/NEW/NA02301/S/RA/LSM
VIRGINIA POWER 1-OP-4.1
NORTH ANNA POWER STATION REVISION 45-P2 PAGE 26 OF 143
4.22 Operations NOT requiring the completion of preceding steps may be done out of
sequence. The Fueling Handling Supervisor or Supervisor Operations Support must
initial and explain any steps done out of sequence on Attachment 5, Step Deviation
Comment Sheet. (Steps done concurrently will NOT be considered out of sequence.)
Completion Signature authority is granted to the Fueling Handling Supervisor or
Supervisor Operations Support only. Unless otherwise noted, other signature authority
may be delegated.
Time:
I
Points:
1.00
Version:
0 1 2345 6789
Answer: BDBACBCBBB
Scramble Range: A - D
RO Tier:
SRO Tier:
T3
Key Word:
REFUELING
Cog. Level:
M 2.5/3.7
Source:
NEW
Exam:
NA02301
Test:
S
Misc:
RA/LSM
Tuesday, July 23, 2002 01:31:36 PM
Unit one is in refueling. While performing 1-OP-4.1, it becomes necessary to perform
two steps out of sequence. Performing these steps requires a completion signature.
According to 1-OP-4.1, which one of the following groups have been granted
completion signature authority to authorize these steps to be completed out of
sequence?
A. Refueling SRO, Superintendent of Operations, and Shift Supervisor.
B" Fuel Handling Supervisor and Supervisor Operations Support.
C. Refueling SRO, Unit SRO, and Fuel Handling Supervisor.
D. Refueling SRO, Unit SRO, Fuel Handling Supervisor, Supervisor Operations
Support, Operations Manager, and Shift Supervisor.
101
100. G2.3.1 00I/T3/T3/2.6/3.0/C/A 2.6/3.0/BANK/NA02301/C/RA/LSM
Given the following:
- Committed Dose Equivalent (CDE) is 2525 mr
- Deep Dose Equivalent (DDE) is 2335 mr
- Lens Dose Equivalent (LDE) is 744 mr
- Committed Effected Dose Equivalent (CEDE) is 405 mr
- Total Organ Dose Equivalent (TODE) is 4865 mr
- Shallow Dose Equivalent (SDE) is 435 mr
- Maximum Extremity (ME) is 6565 mr
Which one of the following is the Total Effective Dose Equivalent?
A. 5270 mr
B. 15249 mr
C. 6444 mr
D' 2740 mr.
Source Bank - 62- ID: 3849
Associated objective(s):
13583
List the following information associated with the radiation protection program
(VPAP-2101).
10-CFR-20 dose limits
Administrative dose limits
Time:
I
Points:
1.00
RO Tier:
Key Word:
Source:
Test:
T3
2.6/3.0
BANK
C
Version:
0 1 23456789
Answer: DAAADACCAA
SRO Tier:
T3
Cog. Level:
C/A
Exam:
Misc:
Scramble Range: A - D
2.6/3.0
02301
RA/LSM
Tuesday, July 23, 2002 01:31:36 PM
102
101. G2.3.2 00 1/T3/T3/ALARA/C/A 2.5/2.9/NEW/NA02301/C/RA/LSM/SC
Switch yard is within the exclusion area boundary and the 22 REM Dose is with-in the
the 25 REM legal limit.
Question replaced at request of utility- New question more closely reflects information
that is required operator knowledge.
When application of process or engineering controls to keep radioactive material in air
below values that constitute an Airborne Radioactivity Area are not practicable, then
VPAP-2102 directs other controls shall be:
implemented to maintain the total effective dose equivalent (TEDE) ALARA.
implemented to maintain the deep Dose Equivalent (DDE) ALARA.
Implemented through the use of a respiratory device with a higher protection factor (PF)
than the peak concentration may be selected to be consistent with TEDE ALARA
Implemented through the use of a respiratory device with a higher protection factor (PF)
than the peak concentration may be selected to be consistent with DDE ALARA.
B & D incorrect because of DDE
B&C incorrect because of higher PF
Source - New
VPAP-2102 REVISION 8 PAGE 16 OF 65
a. Radiation exposure control measures should be designed, selected, implemented,
and maintained to ensure that anticipated and actual doses are ALARA.
b. When application of process or engineering controls to keep radioactive material in
air below values that constitute an Airborne Radioactivity Area are not practicable, then
other controls shall be implemented to maintain the total effective dose equivalent
(TEDE) ALARA. The use (or non-use) of a respiratory device with a lower protection
factor (PF) than the peak concentration may be selected to be consistent with TEDE
Tuesday, July 23, 2002 01:31:36 PM
An accident at NAPS results in a radioactive plume passing over the switchyard. An
operator stationed at the switchyard is exposed to 11 REM/hr whole body dose for a
2-hour period. Which one of the following is correct?
This operator stationed at the switchyard is in the:
A. low population zone and has exceeded 10 CFR100 Limits.
B. low population zone and has NOT exceeded 10 CFR100 Limits.
C. exclusion area and has exceeded 10 CFR100 Limits.
D.' exclusion area and has NOT exceeded 10 CFR100 Limits.
103
ALARA. A Respiratory Hazards evaluation should be a component of a TEDE ALARA
Evaluation.
c. C-HP-1 042.210, Respiratory Hazards Evaluation And Respiratory Protection
Selection, provides several methods to evaluate respiratory hazards due to airborne
radioactive material if historical conditions are not applicable or unavailable. If one
of these methods is used in the TEDE ALARA Evaluation process, list methods
used in part 2.1 of TEDE ALARA Evaluation (Attachment 2) and attach worksheet
from C-HP-1 042.210 to the completed TEDE ALARA Evaluation.
d. A TEDE ALARA Evaluation shall be done if any of the following conditions are
met. Documented evaluations for use (or non-use) of individual respiratory
protection shall be performed on TEDE ALARA Evaluation (Attachment 2) when
activity exposure projections meet one or more of the following:
0.5 rem
- Ratio of dose rate, mrem/hr, to DAC fraction is greater than 50 and without
respirator use, individual DAC-Hour exposure would exceed 10 DAC-Hours
- Requested by Station ALARA Coordinator
e. HP Operations should initiate TEDE ALARA Evaluation (Attachment 2) based on
the above criteria, unless deemed appropriate to do so by the Station ALARA
Coordinator.
f. If initiated outside the Station ALARA Staff, forward TEDE Evaluation form to the
Station ALARA Staff for completion.
Tuesday, July 23, 2002 01:31:36 PM
104
102. G2.4.1 001/T3/T3/IMMEDIATE ACTIONS/M 4.3/4.6/NEW/NA02301 /C/RA/LSM/SC
Solution. B
A - Immediate Action Steps of FR-S.1
B - correct
C - EOP immediate actions SHOULD
The first four Immediate Action Steps
must be performed sequentially.
D - EOP immediate actions SHOULD
The first four Immediate Action Steps
must be performed sequentially
shall be performed in sequence or sequentially
not SHALL be
of E-0 and the
not SHALL be
of E-0 and the
performed from memory, and only
Immediate Action Steps of FR-S.1
performed from memory, and only
Immediate Action Steps of FR-S.1
Reference:
OPAP-0002 REVISION 7 PAGE 24 OF 41
e. Immediate Action Steps
1. EOP Immediate Action Steps should be performed from memory. Immediate Action
Steps are designated by brackets around the individual step number in the applicable
procedures (e.g., [1.])
2. The first four Immediate Action Steps of E-0 and the Immediate Action Steps of
FR-S.1 shall be performed in sequence or sequentially. All other Immediate Action
steps do not have specific step sequence requirements.
3. Immediate Action Steps that have been performed shall be verified when the
EOP is entered.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BCBBDDCCDC
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:37 PM
Which one of the following are correct concerning EOP immediate actions?
A. EOP immediate action steps SHOULD be performed from memory.
The immediate action steps of E-0 SHALL be performed in sequence or
sequentially.
BX EOP immediate action steps SHOULD be performed from memory.
The immediate action steps of E-0 and FR-S.1 ONLY SHALL be performed in
sequence or sequentially.
C. EOP immediate action steps SHALL be performed from memory.
The immediate action steps E-O, FR-S.1, and ECA-0.0 ONLY SHALL be performed
in sequence or sequentially.
D. EOP immediate action steps SHALL be performed from memory and SHALL be
performed in sequence or sequentially.
105
RO Tier:
T3
SRO Tier:
Key Word:
IMMEDIATE ACTIONS
Cog. Level:
Source:
NEW
Exam:
Test:
C
Misc:
103. G2.4.10 001/T3/T3/3.0/3. I/M 3.0/3. 1/NEW/NA0230 1/C/RA/LSM/SC
T3
M 4.3/4.6
NA02301
RA/LSM/SC
a. This is an expected alarm for a normal start of the EDG.
b. Would cause alarm, however the alarm would have come in before the EDG would
have started.
c. Would cause alarm, however the alarm would have come in before the EDG would
have started.
d. Would cause alarm, however the alarm would have come in before the EDG would
have started.
Source - NEW1-AR-21, revision 15, page 3 of 36
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ACCCACDCAA
Scramble Range: A - D
RO Tier:
T3
SRO Tier:
T3
Key Word:
3.0/3.1
Cog. Level:
M 3.0/3.1
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
104. G2.4.16 001/T3/T3/CSFST/M 3.0/4.0/M/NA02301/C/RA/LSM/SC
Tuesday, July 23, 2002 01:31:37 PM
1J EDG has just started. Following the start you receive a "Starting Air Pressure Low"
alarm. Which one of the following is the most probable cause?
A0 This is an expected alarm when the EDG starts.
B. Air compressor control switch is in the off position.
C. Failure of the 1-EG-PS-1JA to start air compressor.
D. Refrigerant air dryer line is frozen.
Which one of the following correctly lists the CSF in DESCENDING order of priority?
A. Subcriticality, Core Cooling, Heat Sink, RCS Inventory, Containment, RCS Integrity.
B. Subcriticality, Containment, Heat Sink, RCS Integrity, Core Cooling, RCS Inventory.
C' Subcriticality, Core Cooling, Heat Sink, RCS Integrity, Containment, RCS Inventory.
D. Subcriticality, Containment, Heat Sink, RCS Inventory, Core Cooling, RCS Integrity.
106
Source BANK Modified 1990/11/26 V. C. Summer 1
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7
Answer: CACCBBAB
RO Tier:
T3
SRO Tier:
Key Word:
Cog. Level:
Source:
M
Exam:
Test:
C
Misc:
105. G2.4.18 001/IT3/E-0/C/A 2.7/3.6/NEW/NA02301/S/RAfLSM/SC
1-E-3 steps 1 through 6.
Procedure change
KA modified on 06/05/02
Time:
I
Points:
RO Tier:
Key Word:
E-0
Source:
NEW
Test:
S
89
D A
Scramble Range: A - D
T3
M 3.0/4.0
NA02301
RA/LSM/SC
NCRODP-92-LP-5
1.00
Version:
0 1 2345 6789
Answer: ADDBBDCADA
Scr
SRO Tier:
T3
Cog. Level:
C/A 2.7/3.6
Exam:
NA02301
Misc:
RA/LSM/SC
"amble Range: A - D
Tuesday, July 23, 2002 01:31:37 PM
You are the US.
-
Unit 1 was at 100% power.
-
A SGTR occurred.
-
The crew is responding to the SGTR in accordance with 1-E-3.
You have just dispatched the turbine building operators to transfer auxiliary steam and
secure powdex system.
Which one of the following describes the reasons that these actions must be taken?
A0 To prevent contamination of the secondary systems.
B. To prevent the release of particulates from the powdex filter elements.
C. To ensure proper steam flow is available, because the auxiliary boiler is unreliable.
D. To prevent lifting the relief valve on the auxiliary steam system.
107
106. G2.4.23 001/F3/r3/RESET/M 2.8/3.8/NEW/NA02301/C/RA/LSM/SC
Which one of the following is correct concerning safety system (e.g. SI, containment
isolation) resets within EOPs?
A. If the system has NOT been reset once, then the crew shall reset the system when
directed by procedure ONLY if it has actuated. This action is not required if the
procedure step includes the words, "if necessary."
B. Once the system has been reset once, it is necessary to reposition the reset
switches every time a procedure directs a reset. Verifying that the applicable status
light still reflects the reset condition is not acceptable.
C.' If the system has NOT been reset once, then the crew shall reset the system when
directed by procedure whether it has actuated or not. This action is not required if
the procedure step includes the words, "if necessary."
D. Once the system has been reset once, it is necessary to reposition the reset
switches ONLY the next time a procedure directs a reset. No additional resets are
required.
Solution - c
a. Does not have to have actuated
b. It is not necessary to reset switches
c. correct answer
d. if it does not, another reset shall be performed
NEW
OPAP-0002 REVISION 7 PAGE 24 OF 41
d. Safety System Resets
1. If the system (e.g., Safety Injection, Containment Isolation) has not been reset
once, then the Reactor Operator shall reset the system when directed by
procedure with concurrence from the cognizant SRO whether it has actuated or
not. This action is not required if the procedure step includes the words if
necessary.
2. Once the system has been reset once, it is not necessary to reposition the reset
switches every time a procedure directs a reset. Verify that the applicable status
light still reflects the reset condition. If it does not, another reset shall be
performed.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: CBABCCACDC
Scramble Range: A - D
RO Tier:
T3
SRO Tier:
T3
Key Word:
RESET
Cog. Level:
M 2.8/3.8
Source:
NEW
Exam:
NA02301
Test:
C
Misc:
RA/LSMISC
Tuesday, July 23, 2002 01:31:37 PM
108
107. G2.4.32 0O1/T3/T3/EPIPS/M 3.3/3.5/BANK!NA02301/C/RA/LSM
Which one of the following station procedures must be initiated if the hathaway
annunciators, the Prodac-250 computer, the PCS computer, and the ERF computer
systems are all inoperable during a unit transient?
A. Emergency Plan Implementing Procedures.
B. Annunciator Response Procedures.
C. Emergency Operating Procedures.
D. Critical Status Function Status Trees.
Source - bank ID: 634
Associated objective(s):
7843
Identify the appropriate controlling station procedure to be used in response to a loss of
the Hathaway annunciators, the Prodac-250 computer, and the ERF computer system
during a unit transient.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: AABCCADDCC
Scramble Range: A - D
RO Tier:
T3
SRO Tier:
T3
Key Word:
Cog. Level:
M 3.3/3.5
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/LSM
108. G2.4.6 001/T3/T3/QUENCH SPRAY/C/A 3.1/4.0/BANK/NA02301/C/RA/LSM
Given a spurious CDA, the operating crew uses E-l, Attachment #3, "Termination of
Quench Spray," as a guide. Which one of the following represents the correct
sequence for securing quench spray?
Af Reset CDA, stop the QS pumps, close the QS pump discharge valves, then close
the CAT discharge valves.
B. Reset CDA, stop the QS pumps, close the CAT discharge valves, then close the
QS pump discharge valves.
C. Stop the QS pumps, close the CAT discharge valves, then close the QS pump
discharge valves.
D. Stop the QS pumps, close the QS pump discharge valves, then reset CDA.
Tuesday, July 23, 2002 01:31:37 PM
109
Source - Bank
ID: 4074
Associated objective(s):
13593
Explain the guidelines for using the following types of procedures (OPAP-0002;
Operating procedures
Emergency operating procedures
Abnormal procedures
Annunciator response procedures
Time:
I
Points:
1.00
Version: 0
Answer: A
RO Tier:
Key Word:
Source:
Test:
T3
QUENCH SPRAY
BANK
C
123456789
BBDCBDBBB
SRO Tier:
T3
Cog. Level:
C/A 3.1/4
Exam:
NA02301
Misc:
RA/LSM
Scramble Range: A - D
109. W/EO3EK3.I 001IT2G2/T2G2/2.8/3.2/C/A 3.3/3.7/NEW/NA02301/C/RA/LSM/SC
Unit 1 is recovering from a small-break LOCA.
ES-1.2, "Post-LOCA Cooldown and Depressurization," is in use.
All ECCS equipment is operating properly.
Depressurization of the RCS has commenced.
Pressurizer (PRZR) level has just risen rapidly from off-scale low to 50%.
Which one of the following is the cause of the rapid increase in PRZR level?
A. A PRZR vapor space leak has developed.
B/ Voiding is occurring in the reactor vessel head.
C. SI flow is refilling the PRZR.
D. Temperature variations are affecting the reference leg of the PRZR level
instrument.
Tuesday, July 23, 2002 01:31:37 PM
110
REFERENCE
ES-1.2 - Post-LOCA Cooldown and Depressurization, Caution prior to Step 12.
Time:
I
RO Tier:
Key Word:
Source:
Test:
T2G2
2.8/3.2
NEW
C
Points:
1.00
Version:
0 1 234567 89
Answer: BABACBDAAB
Scramble Range: A - D
SRO Tier:
T2G2
Cog. Level:
C/A 3.3/3.7
Exam:
NA02301
Misc:
RA/LSM/SC
110. WEO IG2.4.4 001/1 1G2//SI TERMINATION/C/A 4.0/4.3/M/NA02301/R/RA/GWL/SC
line break in containment.
psig.
crew to transition from 1 -E-1
Tuesday, July 23, 2002 01:31:37 PM
- Unit 1 has had a reactor trip and SI due to a main steam
- "B" S/G has boiled dry and pressure is approximately 50
- "A" S/G narrow range level is 20% and slowly rising.
- "C" S/G narrow range level is 10% and slowly rising.
- Total AFW flow is 300 gpm.
- PRZR level is 19% and rising.
- Containment pressure is 21 psia and slowly lowering.
- RCS subcooling is stable at 880F.
- RCS pressure is 1800 psig and slowly rising.
Which one of the following sets of conditions will allow the
to 1-ES-1.1, "SI Termination?"
A. One intact steam generator increases to greater than 11%, and PRZR level
increases to 45%.
B' PRZR level increases to 45%, and AFW flow is raised to 345 gpm.
C. One intact steam generator increases to 23%, and AFW flow is raised to 350 gpm.
D. RCS Subcooling is raised to 100°F, and PRZR level increases to 21%.
ill
Modified from North Anna Bank question # 5019
Associated Objective 13683.
(Adverse Numbers)
A. Incorrect, Steam generator level is required to be > 22%, or AFW flow > 340 gpm.
B. Correct, Pressurizer level must be 40% or greater and AFW Flow > 340 gpm.
C. Incorrect, SG level satisfies one condition, but pressurizer level is still not 40% or
greater.
D. Incorrect, Pressurizer level must be 40% or greater.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BBBABDAACB
Scramble Range: A - D
RO Tier:
TIG2
SRO Tier:
Key Word:
SI TERMINATION
Cog. Level:
C/A 4.0/4.3
Source:
M
Exam:
NA02301
Test:
R
Misc:
RA/GWL/SC
111. WE02EA2.2 001//TIGI/TS/C/A 3.5/4.0/NEW/NA02301/S/RA/LSM
Unit one is in post-LOCA cooldown. The current temperature is 3450F. A mechanical
failure of one train of SI has just occurred. The other train is available.
Which one of the following describes the ITS LCO that applies to this condition?
A. LCO 3.5.2, ECCS - Operating.
B. LCO 3.4.7, RCS Loops - Mode 5, Loops Filled.
C. LCO 3.9.5, Residual Heat Removal and Coolant Circulation-High Water Level.
D. LCO 3.5.3, ECCS - Shutdown.
Tuesday, July 23, 2002 01:31:37 PM
112
One train is required in mode 4 by LCO 3.5.3
North Anna Units 1 and 2 B 3.5.3-2 Rev 0 (Draft 1), 06/05/00
ECCS-Shutdown
B 3.5.3
BASES
LCO
During an event requiring ECCS actuation, a flow path is required to provide an
abundant supply of water from the RWST to the RCS via the ECCS pumps and their
respective supply headers to each of the three cold leg injection nozzles. In the long
term, this flow path may be switched to take its supply from the containment sump and
to deliver its flow to the RCS hot or cold legs.
APPLICABILITY In MODES 1, 2, and 3, the OPERABILITY requirements for ECCS are
covered by LCO 3.5.2.
In MODE 4 with RCS temperature below 350... .F, one OPERABLE ECCS train is
acceptable without single failure consideration, on the basis of the stable reactivity of
the reactor and the limited core cooling requirements.
In MODES 5 and 6, unit conditions are such that the probability of an event requiring
ECCS injection is extremely low. Core cooling requirements in MODE 5 are addressed
by LCO 3.4.7, "RCS Loops-MODE 5, Loops Filled," and LCO 3.4.8, "RCS
Loops-MODE 5, Loops Not Filled." MODE 6 core cooling requirements are addressed
by LCO 3.9.5, "Residual Heat Removal (RHR) and Coolant Circulation-High Water
Level," and LCO 3.9.6, "Residual Heat Removal (RHR) and Coolant Circulation-Low
Water Level."
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: DBCBCCDAAB
Scramble Range: A - D
RO Tier:
SRO Tier:
T1GI
Key Word:
TS
Cog. Level:
C/A 3.5/4.0
Source:
NEW
Exam:
NA02301
Test:
S
Misc:
RA/LSM
Tuesday, July 23, 2002 01:31:38 PM
113
112. WE03EK3. I 001/TI G2/T I G2/ECA-2.1/C/A 3.6/3.9/BANK/NA02301/C/RA/LSM!SC
Given the following conditions:
-
Unit 1 was operating at 100% power.
-
An earthquake resulted in a rupture of the 40" main steam manifold.
-
The operating crew was NOT able to close the MSTVs or the main steam NRVs,
and has transitioned to 1-ECA-2.1.
-
A report comes in from the MSVH that "C" main steam NRV has been closed.
-
The RO observes "C" SG pressure increasing slowly.
Based on the above information, the operating crew should:
A0 transition to 1-E-2.
B. transition to 1-E-3.
C. remain in 1-ECA-2.1 until RHR is in service.
D. remain in 1-ECA-2.1 until SI is terminated.
1996/01/29
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ACAAAADDBC
Scramble Range: A - D
RO Tier:
TIG2
SRO Tier:
T1G2
Key Word:
ECA-2.1
Cog. Level:
C/A 3.6/3.9
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/LSM/SC
113. WE03EK3.2 001//T1G2/E-I/M 3.4/3.9/NEW/NA02301/S/RA/LSM
Unit 1 has just transitioned from 1 -E-1. The crew has entered 1-ES-1.2, "Post-LOCA
Cooldown and Depressurization." At step 5 in the procedure you are directed to place
the PRZR heaters in Pull-to-Lock. Which one of the following is the reason for this?
A. To minimize heat load during the cooldown.
B. To prevent potential overload on any running EDG.
C." To prevent damaging the PRZR heaters.
D. To prevent pressure transients.
Tuesday, July 23, 2002 01:31:38 PM
114
Caution before step five reminds the operator that the PRZR heaters may not be
covered at this point and that the heaters should not be energized until the heaters are
covered.
NEW
KA modified on 06/05/02
Time:
1
Points:
RO Tier:
Key Word:
Source:
Test:
E-1
NEW
S
1.00
Version:
Answer:
0123456789
CCAABCCCCB
SRO Tier:
T1G2
Cog. Level:
Exam:
Misc:
Scramble Range: A - D
M 3.4/3.9
NA02301
RA/LSM
114. WE04EA2.1 001//TIGI/STEAM BREAK/C/A 3.4/4.3/BANK/NA02301/S/RA/LSM
A reactor trip occurs from 65% power and the immediate o
"Reactor Trip or Safety injection," have been completed. I
progress, the crew identifies the following plant conditions.
perator actions of 1-E-0,
n diagnosing the event in
- Pressurizer level is decreasing
- Pressurizer pressure is decreasing
- Containment pressure is 9 psia and stable
- Containment radiation monitors are reading normal
- Reactor Coolant System Tavg is stable at 5470F
- Steam generator levels are consistent between generators
- Auxiliary Building sump level is normal
Which of the following describes the procedure used to mitigate it this event?
AY 1-ECA-1.2, "LOCA Outside Containment."
B. 1 -E-1, "Loss of Reactor or secondary Coolant."
C. 1-E-3, "Steam Generator Tube Rupture."
D. 1-E-2, "Faulted Steam Generator Isolation."
BANK 1996/01/29
VISION OBJ. 12025, SIMULATOR SETUP
Reactor trip status panel
Question modified on 06/04/02 due to KA mismatch.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: ABABCACBBC
Scramble Range: A - D
Tuesday, July 23, 2002 01:31:38 PM
115
RO Tier:
SRO Tier:
TIGI
Key Word:
STEAM BREAK
Cog. Level:
C/A 3.4/4.3
Source:
BANK
Exam:
NA02301
Test:
S
Misc:
RAILSM
115. WE04EK2.1 002/TI G2//E-3/C/A 3.6/4.0/NEW/NA02301/R/RA/LSM
According to 1 -E-3, which one of the following is the reason that feed flow to any
ruptured SG that is faulted should remain isolated unless needed for cooldown?
Af To prevent excessive RCS cooldown.
B. To prevent spread of contamination.
C. To prevent dilution of the RCS.
D. To prevent loss of feed flow inventory.
Note prior to step 4 1-E-3, rev 19
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: AADADBADBB
Scramble Range: A - D
RO Tier:
T1G2
SRO Tier:
Key Word:
E-3
Cog. Level:
C/A 3.6/4.0
Source:
NEW
Exam:
NA02301
Test:
R
Misc:
RA/LSM
116. WE05EKI.2 ooi/TIG2/TtG2/3.9/4.5/M 3.9/4.5/NEW/NA02301/C/RA/LSM/SC
Operators are responding to three faulted steam generators. The heat sink status tree
has a red terminus.
Which one of the following is the reason that the operators should NOT perform any
steps in 1-FR-H.1?
Operator actions taken in 1-ECA-2.1 have:
Af reduced total AFW flow.
B. reduced RCS pressure.
C. increased total AFW flow.
D. increased RCS pressure.
Tuesday, July 23, 2002 01:31:38 PM
116
NEW
Reference 1-FR-H.1, Revision 13, page 2 of 15
Note prior to step one indicated that procedure cannot be entered if AFW flow is less
that 340 because of operator actions.
a. correct answer
b. RCS only applies if greater than any NON-Faulted SG Pressure
c. RCS only applies if greater than any NON-Faulted SG Pressure
d. RCS only applies if greater than any NON-Faulted SG Pressure, RCP pump statu
does not apply here
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: AADCCDAC
SRO Tier:
Cog. Level:
Exam:
Misc:
A C
Scr
TIG2
M 3.9/4.5
NA02301
RA/LSM/SC
amble Range: A - D
117. WE06EK2.2 00I/TIGI/TIGI/CORE COOLING/C/A 3.8/4.I/BANK/NA02301/C/RA/LSM
NCRODP-95.6,
1992 bank
Time:
I
RO Tier:
Key Word:
Source:
Test:
TIGI
CORE C(
BANK
C
Revision 2, Page 3.9, Step 11, Objective D.
Points:
1.00
Version:
0 1 23456789
Answer: BDACCAADDA
S
SRO Tier:
TIGI
)OLING
Cog. Level: C/A 3.8/4.1
Exam:
NA02301
Misc:
RA/LSM
cramble Range: A - D
Tuesday, July 23, 2002 01:31:38 PM
RO Tier:
Key Word:
Source:
Test:
TIG2
3.9/4.5
NEW
C
S
While responding to inadequate core cooling in accordance with 1-FR-C.1, which one
of the following describes how core recovery by SI accumulator injection is initiated?
A. Dumping steam to the condenser and initiating forced two-phase flow using the
RCPs.
B.0 Dumping steam to the condenser or using SG PORVs.
C. Restarting the RCPs to sweep steam voids and nitrogen gas from the core.
D. Increasing nitrogen pressure on the top of the SI accumulators to increase the
injection rate into the RCS.
117
118. WE08EKI .2 001/TIGl/TIGI/PTS/M 3.4/4.0/BANK/NA02301/C/RA/GWL/SC
- Unit 2 has experienced a main steam line break.
- All systems operated as designed.
- The crew responded in accordance with the emergency operating procedures, and is
currently in 2-FR-P.I.
- The crew has been directed by the procedure to perform a soak.
Which one of the following evolutions can be performed during the soak?
A. Warm up the RHR System and place it in service.
B?' Un-isolate charging pump recirculation.
C. Raise steam generator narrow-range levels to 50% and secure AFW pumps.
D. Energize the pressurizer heaters.
North Anna Exam bank questions # 3109 and 3585.
A. Incorrect, warming up the RHR system could cooldown the RCS even more, and
placing it in
service would cooldown the RCS.
B. Correct, unisolating the charging pump recirculation would tend to lower RCS
pressure, and
would not raise pressure or cause a cooldown.
C. Incorrect, raising steam generator water levels would cause an RCS cooldown.
D. Incorrect, Energizing the pressurizer heaters would raise RCS pressure resulting in
increased
thermal stresses.
Time:
I
Points:
1.00
Version:
0 1 2 34 5 6 7 89
Answer: BCCADADAAA
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
TIGI
Key Word:
Cog. Level:
M 3.4/4.0
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/GWL/SC
Tuesday, July 23, 2002 01:31:38 PM
118
119. WE09EA 1.2 00/iT1Gi /T IGI/NATURAL CIRC/M 3.6/3.9/BANK/NA02301/C/RA/GWL/SC
- A natural circulation cooldown is in progress.
- Steam generator feed flow rate is increased.
- Assume all parameters are within limits.
Which one of the following describes how this will affect the natural circulation flow
rate?
Natural circulation flow rate will:
A. decrease.
B. not be affected.
C. be stopped, and will not recommence.
D' increase.
From Farley exam bank.
North Anna associated objective 12484 and 13435.
A. Incorrect, slowly increasing steam flow from the steam generators will increase
natural circulation flow.
B. Incorrect, Natural circulation flow will be affected.
C. Incorrect, Natural circulation flow may be stopped momentarily if the steam demand
was increased to much, but would re-establish it self, at a higher flow rate.
D. Correct, increasing the steaming rate on the S/G will increse the natural circulation
flow rate.
Time:
I
Points:
1.00
Version:
0 1 2 34 567 89
Answer: DACBADAABB
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
TIGI
Key Word:
NATURAL CIRC
Cog. Level:
M 3.6/3.9
Source:
BANK
Exam:
NA02301
Test:
C
Misc:
RA/GWL/SC
Tuesday, July 23, 2002 01:31:38 PM
119
120. WEIl EK2.2 oo0iT 0G2/T 0G2/HEAT REMOVAL/C/A 3.9/4.3/BANK/NA02301/C/RA/LSM/SC
Given the following conditions:
- A LOCA has occurred.
- A CDA signal was received.
- The current containment pressure is 25 psia and decreasing.
- The RWST level is 20% and decreasing.
Which one of the following describes the action to be taken by the operator?
A. Momentarily place the spray actuation reset switches in RESET to reset the CDA
signal.
B' Verify changeover from injection mode to recirculation mode or shift manually if not
yet accomplished.
C. Reset the CDA signal and stop the quench spray pumps to let the pressure decay
naturally and conserve resources.
D. Refill the RWST from the CVCS and continue to spray down containment until
pressure is 12 psia.
1992/02/24
L.P. NCRODP-91-1-LP-3, Rev. 4, page 13, Objective B
Time:
I
RO Tier:
TIG
Key Word:
HEA
Source:
BAN
Test:
C
2
T RI
K
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: BDABDCBDDA
Sc
SRO Tier:
TIG2
EMOVAL
Cog. Level: C/A 3.9/4.3
Exam:
NA02301
Misc:
ramble Range: A - D
RA/LSM/SC
Tuesday, July 23, 2002 01:31:38 PM
120
121. WE12EK3.3 001/TI GI//FEEDWATER/M 3.5/3.7/M/NA02301/R/RA/GWL/SC
Modified from North Anna Bank questions, # 3055,2885, and 3767.
Associated objectives 13842, and 13843.
A. Incorrect, While in ECA-2.1 AFW flow is to be limited to 100 gpm for each generator.
340
gpm is the correct flow rate for other ERGs, and the reason is correct for
those procedures.
B. Correct, 100 gpm should be delivered to each steam generator, and this is the
correct reason listed in the WOG background documents.
C. Incorrect, This is the incorrect amount, while this would prevent overheating of the
pumps, this is not the reason that flow is limited in ECA 2.1.
D. Incorrect, 100 gpm total to all generators is not correct(100 to each S/G is
required), the
RCS will re pressurize when cooldown (shrinkage of the RCS
can be made up by the Safey
Injection systems.
Time:
I
Points:
1.00
Version:
0 1 23456789
Answer: BCCADADADC
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
Key Word:
Cog. Level:
M 3.5/3.7
Source:
M
Exam:
NA02301
Test:
R
Misc:
RA/GWL/SC
Tuesday, July 23, 2002 01:31:39 PM
Assume the following plant conditions:
- All steam generators are depressurizing uncontrollably.
- Narrow range level in each steam generator is offscale low.
Which one of the following correctly describes how feedwater flow to the steam
generators should be controlled, and why this is necessary?
A. Maintain a minimum of 340 gpm total to all steam generators, this is the minimum
flow required to ensure decay heat removal is sufficient to prevent fuel damage.
B. Maintain a minimum of 100 gpm to each steam generator, this will minimize thermal
shock effects if feedwater flow is increased.
C. Maintain a minimum of 340 gpm total to all steam generators not isolated, this will
prevent overheating of the AFW pumps due to running at low flow conditions for
long periods of time.
D. Maintain a minimum of 100 gpm total to all steam generators, this is the minimum
flow required to prevent the Reactor Coolant System from re-pressurizing.
121
122. WE 12G2.4.22 001//T 1GI/SG LEVEL/C/A 3.0/4.3/M/NA02301/S/RA/LSM
1-E-1, Step 3, Check Intact SG Levels, reads:
- Narrow range level - greater than 11% [23%]
- Control feed flow to maintain narrow range level between 23% and 50%
Which one of the following is the reason or basis for these actions?
To maintain RCS heat sink and:
A. minimize pressurized thermal shock.
B/ establish symmetric cooling of the RCS.
C. maintain the SGs in a wet condition.
D. to establish conditions to prevent core reflux boiling.
1-E-1 Rev 15, Owners Group Guidelines,
NCRODP-95.4, Revision 4, Pages 5.11 & 5.12, Objective D.
MODIFIED BANK 1992
Time:
I
Points:
1.00
Version:
0 1 2 3 45 6789
Answer: BBBDCADDDB
Scramble Range: A - D
RO Tier:
SRO Tier:
TIGI
Key Word:
SG LEVEL
Cog. Level:
C/A 3.0/4.3
Source:
M
Exam:
NA02301
Test:
S
Misc:
RA/LSM
Tuesday, July 23, 2002 01:31:39 PM
122
123. WE14EA1.3 001/TIG1/TIGI/CONTAINMENT/C/A 3.3/3.8/M/NA02301/C/RA/GWL/SC
- A reactor trip and safety injection has occurred on unit 1.
- CDA has NOT actuated.
- All steam generator pressures are stable at approximately 800 psig.
- Containment pressure as indicated on recorder 1 -LM-PR-1 10B is 29 psia and slowly
decreasing.
- 1-E-0 is in effect and the crew has just completed performing the immediate actions.
Which one of the following correctly describes the actions that the crew should take?
A. Start the quench spray pumps and open pump discharge and chemical addition
tank valves.
B/ Manually acuate CDA, and ensure CDA actions are complete.
C. Continue in 1-E-0, address CDA actions when they reach the procedure step.
D. Go to 1-FR-Z.1, "Response to High Containment Pressure."
Modified From North Anna Bank Question 3312,3320 and 3861. Associated objective
s12460, and 12467.
A. Incorrect, this would be the correct action that would be required if containment
pressure exceeded 20 psia and a CDA was not required.
B. Correct, if containment pressure exceeded 28 psia a CDA should have occured and
the crew should initiate a CDA.
C. Incorrect, the crew should perform CDA actions per the continuous action page and
not wait until reaching the procedure step.
D. Incorrect, FR-Z.1 has steps that will address these conditions, but should not be
used until E-0 is exited.
Time:
I
Points:
1.00
Version:
0 1 2 3 4 5 6 7 8 9
Answer: BBACCBDAAA
Scramble Range: A - D
RO Tier:
TIGI
SRO Tier:
TIGI
Key Word:
CONTAINMENT
Cog. Level:
C/A 3.3/3.8
Source:
M
Exam:
NA02301
Test:
C
Mise:
RA/GWL/SC
Tuesday, July 23, 2002 01:31:39 PM
123
124. WE] 5EKI .1 001T10G3/T 1G3/FLOODING/M 2.8/3.0/NEW/NA02301/C/RA/LSM/SC
New
Per O-AP-39.2 Revision
charging.
6, Page 2. Auxiliary Building Flooding could cause a loss of
Time:
I
RO Tier:
Key Word:
Source:
Test:
TIG3
FLOODI]
NEW
C
Points:
1.00
Version:
0 1 23456789
Answer: ADBDCCBADD
SRO Tier:
TIG
NG
Cog. Level:
M 2
Exam:
Misc:
RA/
Scn
- 3
.8/3.0
02301
'LSrM/SC
amble Range: A - D
125. WEI6EKI .3 001ff I G2/TIG2/WASTE GAS/M 3.0/3.3/BANK/NA02301/C/RA/LSM/SC
Which one of the following statements is correct if a high-high alarm is initiated by
process vent particulate radiation monitor 1-RM-VG-101 during a waste gas decay tank
release?
A. 1-GW-FCV-101 (decay tanks effluent flow control) will close automatically and must
be reset locally before it can be reopened.
B. 1-GW-TV-102A (containment vacuum pump discharge) will close automatically, and
will reopen when the alarm condition clears and the OPEN pushbutton is
depressed.
C. 1-GW-TV-102A (containment vacuum pump discharge) will close automatically and
must be reset locally before it can be reopened.
D. 1-GW-FCV-101 (decay tanks effluent flow control) will close automatically and will
reopen automatically when the alarm condition clears and the CLOSE pushbutton is
depressed.
Bank 16 ID: 3812
Tuesday, July 23, 2002 01:31:39 PM
The control room receives reports of flooding in the auxiliary building. The crew enters
O-AP-39.2. Which one of the following systems could be damaged by this flooding?
A' Charging.
B. Pressurizer spray.
C. Containment ventilation.
D. Boric acid transfer.
124
Time:
I
RO Tier:
Key Word:
Source:
Test:
TIG2
WASTE
BANK
C
Points:
1.00
Version:
0 1 23456789
Answer: BAADADACAA
Scrn
SRO Tier:
TIG2
GAS
Cog. Level:
M 3.0/3.3
Exam:
NA02301
Misc:
RA/LSM/SC
amble Range: A - D
Tuesday, July 23, 2002 01:31:39 PM
125