2CAN040301, Annual Report of Steam Generator Tubing In-service Inspections

From kanterella
Jump to navigation Jump to search
Annual Report of Steam Generator Tubing In-service Inspections
ML031080421
Person / Time
Site: Arkansas Nuclear Entergy icon.png
Issue date: 04/11/2003
From: Cotton S
Entergy Operations
To:
Document Control Desk, Office of Nuclear Reactor Regulation
References
2CAN040301
Download: ML031080421 (6)


Text

EnterI gy Entergy Operations, Inc 1448 SR 333 Russeliville, AR 72802 Tel 501 858 5000 2CAN040301 April 11, 2003 U. S. Nuclear Regulatory Commission Document Control Desk Mail Station OP1-17 Washington, DC 20555

Subject:

Arkansas Nuclear One - Unit 2 Docket No. 50-368 License No. NPF-6 2003 Annual Report of Steam Generator Tubing In-service Inspections

Dear Sir or Madam:

Arkansas Nuclear One, Unit 2 (ANO-2) Technical Specifications 4.4.5.5.b and 6.9.1.5.b require that results of ANO-2 steam generator (SG) tubing in-service inspections performed during the report period be submitted to the NRC on an annual basis. Attached is the Steam Generator Tubing In-service Inspection Annual Report which presents the results from ANO-2's scheduled refueling outage (2R15) inspection. These inspections were completed on April 24, 2002.

This submittal completes the reporting requirements of ANO-2 Technical Specifications 4.4.5.5.b and 6.9.1.5.b for 2003. This submittal contains no commitments.

Should you have any questions regarding this issue, please contact Fred Van Buskirk of my staff at (479) 858-3155.

Sincerely, Sherrie R. Cotton Director, Nuclear Safety Assurance SRC/fpv Attachment 43(447

2CAN040301 Page 2 of 2 cc wI att: Mr. Ellis W. Merschoff Regional Administrator U. S. Nuclear Regulatory Commission Region IV 611 Ryan Plaza Drive, Suite 400 Arlington, TX 76011-8064 NRC Senior Resident Inspector Arkansas Nuclear One P.O. Box 310 London, AR 72847 U. S. Nuclear Regulatory Commission Attn: Mr. Thomas W. Alexion MS O-7D1 Washington, DC 20555-0001

Attachment to 2CAN040301 Page 1 of 4 ARKANSAS NUCLEAR ONE, UNIT 2 STEAM GENERATOR TUBING IN-SERVICE INSPECTION ANNUAL REPORT 1 INTRODUCTION Arkansas Nuclear One, Unit 2 (ANO-2) Technical Specification (TS) 4.4.5.5.b requires Entergy Operations to submit an annual report to the NRC that outlines the details of the steam generator (SG) tubing in-service inspections that were performed during the reporting period. The report shall include:

1. Number and extent of tubes inspected
2. Location and percent of wall-thickness penetration for each indication of an imperfection.

3 Identification of tubes plugged The operating period for this report includes one outage, a refueling inspection (2R15) in April 2002.

2 DESIGN The replacement steam generators are Westinghouse (W) Model Delta 109s. They consist of Inconel 690 thermally treated tubing that is 11/16" in diameter with a 0.040" wall thickness The tubes are expanded full depth hydraulically in the tubesheet The tube supports are constructed of stainless steel and are a broached trefoil-hole design. The upper bundle supports consist of five sets of staggered stainless steel anti-vibration bars (AVBs) that are numbered AO1-A20.

Attachment to 2CAN040301 Page 2 of 4 3 2R15 OUTAGE RESULTS 3.1 2R15 Scope Table 3.1 lists the inspection scope of 2R15.

Table 3.1 2R15 Inspection Scope SG "A" Examination Type Inspections Conducted  % Scope Extent Tested Bobbin 10637 100 TEC to TEH Row 1&2 U-Bend 181 100 08H to 08C Bobbin I-Codes 15 N/A N/A SG "B" Examination Type Inspections Conducted  % Scope Extent Tested Bobbin 10636 J 100 J TEC to TEH Row 1&2 U-Bend 181 100 08H to 08C Bobbin I-Codes 11 N/A N/A TEC - Tube End Cold TEH - Tube End Hot 3.2 Degradation Mechanisms Found Table 3.2 outlines the number of indications found during the outage.

Table 3.2 2R15 Inspection Results Location SG "A" SG "B" AVB Wear l 0_l 1 Loose Part Wear _ 2 Manufacturing Burnish Marks (MBM) 139 216 Dents (Pre-service) 1017 596

Attachment to 2CAN040301 Page 3 of 4 3.3 NDE Techniques Utilized Table 3.3 identifies the non-destructive examination (NDE) technique used for each location:

Table 3.3 2R15 NDE Techniques Location NDE Technique Bobbin 0.560" Bobbin U-Bend 0 520" Plus Point Coil Special Interest 0.520" or 0.560" Plus Point Coil 3.4 Number of Tubes Plugged or Repaired by Damage Mechanism There were no plugs or sleeves installed during 2RI 5.

3.5 Number and Percent Plugged and Sleeved Following 2R15 The number of tubes plugged or sleeved following 2R15 is shown in Table 3.5.

Table 3.5 Cumulative Plugs and Sleeves in Service SG "A" SG "B' Sleeves 0 0 Pre-service I-690 Welded 0 1 Post Installation Plugs 0 0 Percent Plugged 0.000 % 0.009 %

3.6 Description of Tube Integrity Assessment The operational assessment was performed using deterministic methods for the identified damage mechanism and justified operation for the next two cycles. All performance criteria were met.

3.7 Description of Corrective Actions There were no corrective actions taken since all tests met the specified criteria

Attachment to 2CAN040301 Page 4 of 4 3.8 Evaluation of Exceeding Condition Monitoring Not applicable since all conditions were met.

3.9 Item #2 of the Technical Specification (location and percent of wall-thickness penetration for each indication of an imperfection)

This topic is addressed in Table 3.9 for SG "B" below. There were no indications identified in SG "A".

TABLE 3.9 SG "B" INDICATION LIST FOR 2R15 No. Row Column Indication Location Reason  % TW 1 100 25 VOL TSC +12.8 Loose Part 18 2 102 25 VOL TSC +12.3 Loose Part 4 3 109 92 WAR All -0.17 AVB Wear 12 Legend:

VOL - Volumetric WAR - Anti-Vibration Bar Wear TSC - Tubesheet Cold Al l - I lh Anti-Vibration Bar TW - Through Wall