ML17285A321: Difference between revisions
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
||
Line 14: | Line 14: | ||
| document type = OPERATING LICENSES-APPLIATION TO AMEND-RENEW EXISTING, TEXT-LICENSE APPLICATIONS & PERMITS | | document type = OPERATING LICENSES-APPLIATION TO AMEND-RENEW EXISTING, TEXT-LICENSE APPLICATIONS & PERMITS | ||
| page count = 8 | | page count = 8 | ||
| project = | |||
| stage = Request | |||
}} | }} | ||
Line 49: | Line 51: | ||
The proposal to perform channel functional testing on a semi-annual frequency instead of monthly is based on 1), the manufacturer,'s total channel drift as compared to that experienced by the presently installed Riley instruments and 2), an analysis of the minimum changes in temperature between trip setpoint and allowable value .allowed by the technical specifications compared to the manu-facturer's specified total channel drift. Observed drift values on the Riley instrumentation have been as gigh as 7 F per, month. The NUMAC equipment drift specification is less than 0.7 F per month, which is one-tenth of that observed in the Riley equipment. Additionally, the minimum margin between Trip setpoint and Allowable Value for the temperature monitoring system variables as noted in Technical Specifjcation Table 3.3.2-2, Isolation Actuation Instrumentation Setpoi nts, is 10 F. Using this value and the manufacturer.'s specified drift (less than 0.7 F), the changing of channel functional testing from monthly to semi-annually fog the new system will leave a margin to the allowable value of greater. than 5.8 F. Using this same drift value, the new instrumentation could be channel functional tested each 10 months and provide approximately the same margin observed, at times, with the present instrumentation. As discussed above, failure mode diagnostic featur es are continuous and preclude the necessity of confirmation during channel functional testing. Hence, the diagnostic and drift characteristics of the NUMAC equipment assure greater confidence in system operability when functionally tested on a semi-annual<,'asis than the Riley equipment tested monthly. | The proposal to perform channel functional testing on a semi-annual frequency instead of monthly is based on 1), the manufacturer,'s total channel drift as compared to that experienced by the presently installed Riley instruments and 2), an analysis of the minimum changes in temperature between trip setpoint and allowable value .allowed by the technical specifications compared to the manu-facturer's specified total channel drift. Observed drift values on the Riley instrumentation have been as gigh as 7 F per, month. The NUMAC equipment drift specification is less than 0.7 F per month, which is one-tenth of that observed in the Riley equipment. Additionally, the minimum margin between Trip setpoint and Allowable Value for the temperature monitoring system variables as noted in Technical Specifjcation Table 3.3.2-2, Isolation Actuation Instrumentation Setpoi nts, is 10 F. Using this value and the manufacturer.'s specified drift (less than 0.7 F), the changing of channel functional testing from monthly to semi-annually fog the new system will leave a margin to the allowable value of greater. than 5.8 F. Using this same drift value, the new instrumentation could be channel functional tested each 10 months and provide approximately the same margin observed, at times, with the present instrumentation. As discussed above, failure mode diagnostic featur es are continuous and preclude the necessity of confirmation during channel functional testing. Hence, the diagnostic and drift characteristics of the NUMAC equipment assure greater confidence in system operability when functionally tested on a semi-annual<,'asis than the Riley equipment tested monthly. | ||
Page 4 REQUEST FOR AMENDMENT TO TECHNICAL SPECIFICATION TABLE 4.3.2.1"1, ISOLATION ACTUATION INSTRUMENTATION SURVEILLANCE REQUIREMENTS The Supply System has evaluated this amendment request per, | Page 4 REQUEST FOR AMENDMENT TO TECHNICAL SPECIFICATION TABLE 4.3.2.1"1, ISOLATION ACTUATION INSTRUMENTATION SURVEILLANCE REQUIREMENTS The Supply System has evaluated this amendment request per, 10CFR50.59 and 50.92 and determined that it does not represent an unreviewed safety question or a significant hazard because it does not: | ||
: 1) Involve a significant increase in the probability or consequences of an accident previously evaluated because, as discussed above, the NUMAC design features and diagnostic, self-test, and low drift value preclude the necessity to perform channel checks and allow the change in channel func-tional testing to semi-annual while actually enhancing the ability to assess operability and functionality of the leak detection system. Deletion of the obsolescent channel check increases operator, availability and can be considered a contribution towards decreasing the probability or, consequences of accidents. Semi-annual channel functional testing of the NUMAC equipment provides more margin to Allowable Values than testing the present equipment on a monthly basis. Hence, the probability or. consequences of previously evaluated accidents are not increased by this change. | : 1) Involve a significant increase in the probability or consequences of an accident previously evaluated because, as discussed above, the NUMAC design features and diagnostic, self-test, and low drift value preclude the necessity to perform channel checks and allow the change in channel func-tional testing to semi-annual while actually enhancing the ability to assess operability and functionality of the leak detection system. Deletion of the obsolescent channel check increases operator, availability and can be considered a contribution towards decreasing the probability or, consequences of accidents. Semi-annual channel functional testing of the NUMAC equipment provides more margin to Allowable Values than testing the present equipment on a monthly basis. Hence, the probability or. consequences of previously evaluated accidents are not increased by this change. | ||
: 2) Create the possibility of a new or, different kind of accident from any accident pr eviously evaluated because operability and functionality of the system is enhanced with the diagnostic self-test and drift features of the NUMAC equipment. The assessment of channel behavior is made on a 30-minute interval with the NUMAC equipment. This assessment will identify system failures and malfunction much sooner than the present 12 hour manual channel check. As such, the possibility of a new or, different kind of accident due to deletion of the manual check is not credible. The semi-annual channel functional test assur es, with a large measure of conser vatism, that margins realized on monthly functional testing of the present equipment are pre-served. Again a new or, different kind of accident due to functional testing on a semi-annual ver sus monthly frequency is not credible. | : 2) Create the possibility of a new or, different kind of accident from any accident pr eviously evaluated because operability and functionality of the system is enhanced with the diagnostic self-test and drift features of the NUMAC equipment. The assessment of channel behavior is made on a 30-minute interval with the NUMAC equipment. This assessment will identify system failures and malfunction much sooner than the present 12 hour manual channel check. As such, the possibility of a new or, different kind of accident due to deletion of the manual check is not credible. The semi-annual channel functional test assur es, with a large measure of conser vatism, that margins realized on monthly functional testing of the present equipment are pre-served. Again a new or, different kind of accident due to functional testing on a semi-annual ver sus monthly frequency is not credible. |
Revision as of 06:54, 10 November 2019
ML17285A321 | |
Person / Time | |
---|---|
Site: | Columbia ![]() |
Issue date: | 03/08/1989 |
From: | Sorensen G WASHINGTON PUBLIC POWER SUPPLY SYSTEM |
To: | NRC OFFICE OF INFORMATION RESOURCES MANAGEMENT (IRM) |
Shared Package | |
ML17285A322 | List: |
References | |
GO2-89-038, GO2-89-38, TAC-72620, NUDOCS 8903170136 | |
Download: ML17285A321 (8) | |
Text
AC CELE RATED D1~BUTIOY DEMONSTPTION SYSTEM r
REGULATORY INFORMATION DISTRIBUTION SYSTEM (RIDS)
ACCESSION NBR:8903170136 DOC.DATE: 89/03/08 NOTARIZED: YES DOCKET FACIL:50-397 WPPSS Nuclear Project, Unit 2, Washington Public Powe 05000397 AUTH. NAME AUTHOR AFFILIATION SORENSEN,G.C. Washington Public Power Supply System RECIP.NAME RECIPIENT AFFILIATION Document Control Branch (Document Control Desk)
SUBJECT:
Application for amend to License NPF-21,revising Tech Spec Table 4.3.2.1-1.
DISTRIBUTION CODE: AOOID TITLE: OR COPIES RECEIVED:LTR Submittal: General Distribution g ENCL g SIZE: k1 3 NOTES:
RECIPIENT COPIES RECIPIENT COPIES ID 'CODE/NAME LTTR ENCL ID CODE/NAME LTTR ENCL PD5 LA 1 0 PD5 PD 2 2 SAMWORTH, R 1 1
,INTERNAL: ACRS '6 6 ARM/DAF/LFMB 1 0 NRR/DEST/ADS 7E 1 1 NRR/DEST/CEB 8H 1 1 NRR/DEST/ESB 8D 1 1 NRR/DEST/MTB 9H 1 1 NRR/DEST/RSB 8E 1 1 NRR/DEST/SICB 1 r 1 NRR/DOEA/TS B 11 1 1 GGSzhBSTRACT 1 1 OGC/HDS2 1 0 REG 01 1 1 RES/DSIR/EIB 1 1 EXTERNAL: LPDR 1 1 NRC PDR 1 1 NSIC 1 1 mrZ TO mx. iiRIDS>> RECIPIENTS:
PLEASE HELP US Io REDUCE WASTE. CONIACr XHE DOCUMEMI'ONTROL DESK, ROOM Pl-37 (EXT. 20079) %0 ELIKCNATE YOUR NAME PRK DISTIUBVTIOH LISTS FOR DOCUMENTS YOU DON'T NEEDI TOTAL NUMBER OF COPIES REQUIRED: LTTR 25 ENCL 22
WASHINGTON PUBLIC POWER SUPPLY SYSTEM P.O. Box 968 ~ 3000 George Washington Way ~ Richland, Washington 99352 March 8, 1989 G02-89-038 Docket No. 50-397 Nuclear, Regulatory Commission Attn: Document Control Desk Mail Station Pl-137 Washington, D. C. 20555 Gentlemen:
Subject:
NUCLEAR PLANT NO. 2 OPERATING LICENSE NPF-21, REQUEST FOR AMENDMENT TO TECHNICAL SPECIFICATION TABLE 4.3.2.1"1, ISOLATION ACTUATION INSTRUMENTATION SURVEILLANCE RE(}UI REMENTS In accordance with the Code of Federal Regulations, Title 10, Parts 50.90 and 2.101, the Supply System hereby submits a request for, amendment to the WNP-2 Technical Specifications. Specifically, the Supply System is requesting that the subject table be modified, as attached, to reflect enhanced operating capabilities of the leak detection system due to replacement of the present equipment (based on Riley Model 86 temperature switches) with General Electric Nuclear Measurement Analysis and Control (NUMAC) micro-computer, based instru-mentation.
During the upcoming spring refueling outage the Supply System intends to replace the Riley temperature switches in the leak detection system with General Electric Nuclear Measurement and Control instrumentation. The NUMAC equipment will receive signals from the presently installed thermocouples and provide alarm and trip signals to existing circuitry. All functions of the leak detection system will remain, the cHange is being made to enhance overall system reliability. WitH enhanced capabilities the applicable technical speci-fication requirements should be changed to recognize the improvements. Since installation will be completed during the spring refueling outage the proposed technical specification change will be the most beneficial if effective by June 1989.
( 89 f70136 390308 0500039 PDR ADDCK PDC p
<) I
Page 2
'EQUEST FOR AMENDMENT TO TECHNICAL SPECIFICATION TABLE 4-3-2.1-1, ISOLATION ACTUATION INSTRUMENTATION SURVEILLANCE REQUIREMENTS Presently the technical speci fi cation requires channel checks and channel functional tests on a 12-hour and monthly frequency respectively. Due to the enhanced capabilities of the NUMAC instrumentaton, the Supply System proposes
'o amend the Technical Specifications to 1) eliminate the 12-hour channel check requirement based on diagnostic and self-test features provided in the NUMAC design and 2) change the channel functional test frequency from monthly to semi-annually based on the significantly better. total channel drift charac-teristics of the NUMAC equipment and the diagnostic and self-test features of the design.
Presently the channel check of the instrumentation requires that an operator read the output of each channel and compare the reading to expected and similar, channel readings on a 12-hour, basis. Fifty-nine thermocouples are presently manually selected and assessed to complete the channel check. As a result, the process has potential for, human error, and consumes operator, time that could be utilized elsewhere. Failure of the Riley instruments could remain unnoticed until the next channel check (12-hours later). The NUMAC replacement instru-mentation, Quality Class 1 and seismically qualified, has the following diagnostic and self-test features:
o Continually senses an open thermocouple (no input signal) and provides a trouble alarm.
o Continually monitors two internal power supplies and provides a trouble alarm should one fail. The monitors remain functional with one power supply.
o Continually monitors power input to the module and provides a trouble alarm on loss of power.
o Self-checks each channel utilizing a micro-pulse signal through the channel to confirm functionality on a 30-minute frequency and pro-vides a trouble alarm on failure of the self test.
o Provides a trouble alarm if the module is left in'n inoperable condi-tion (card-out-of-file, instrument left in an instrument-out-of-operate mode).
Page 3 REQUEST FOR AMENDMENT TO TECHNICAL SPECIFICATION TABLE 4.3.2.1"1, ISOLATION ACTUATION INSTRUMENTATION SURVEILLANCE REQUIREMENTS These design features provide a more comprehensive assessment of system opera-bility every 30 minutes than that presently provided by the Riley instrument channel check on a 12-hour basis. Essentially, a 30-minute channel check feature is inherent in the design that far, surpasses and precludes the necessity of the channel check presently performed. Utilization of the NUMAC instrumentation channel check feature provides greater, and more frequent assessment of system operability, is more resistant to human error, and will avoid the use of an operator,'s time for an obsolescent function (channel check-ing manually). Continuation of a channel check requirement for, the NUMAC equipment will consume man hours and not provide any greater, assessment of system operability over, that provided by the above design features. From the standpoint of efficient use of an operator,'s time in the assurance of plant safety, a manual channel check requirement for, the new equipment detracts from the operator,'s mission.
The proposal to perform channel functional testing on a semi-annual frequency instead of monthly is based on 1), the manufacturer,'s total channel drift as compared to that experienced by the presently installed Riley instruments and 2), an analysis of the minimum changes in temperature between trip setpoint and allowable value .allowed by the technical specifications compared to the manu-facturer's specified total channel drift. Observed drift values on the Riley instrumentation have been as gigh as 7 F per, month. The NUMAC equipment drift specification is less than 0.7 F per month, which is one-tenth of that observed in the Riley equipment. Additionally, the minimum margin between Trip setpoint and Allowable Value for the temperature monitoring system variables as noted in Technical Specifjcation Table 3.3.2-2, Isolation Actuation Instrumentation Setpoi nts, is 10 F. Using this value and the manufacturer.'s specified drift (less than 0.7 F), the changing of channel functional testing from monthly to semi-annually fog the new system will leave a margin to the allowable value of greater. than 5.8 F. Using this same drift value, the new instrumentation could be channel functional tested each 10 months and provide approximately the same margin observed, at times, with the present instrumentation. As discussed above, failure mode diagnostic featur es are continuous and preclude the necessity of confirmation during channel functional testing. Hence, the diagnostic and drift characteristics of the NUMAC equipment assure greater confidence in system operability when functionally tested on a semi-annual<,'asis than the Riley equipment tested monthly.
Page 4 REQUEST FOR AMENDMENT TO TECHNICAL SPECIFICATION TABLE 4.3.2.1"1, ISOLATION ACTUATION INSTRUMENTATION SURVEILLANCE REQUIREMENTS The Supply System has evaluated this amendment request per, 10CFR50.59 and 50.92 and determined that it does not represent an unreviewed safety question or a significant hazard because it does not:
- 1) Involve a significant increase in the probability or consequences of an accident previously evaluated because, as discussed above, the NUMAC design features and diagnostic, self-test, and low drift value preclude the necessity to perform channel checks and allow the change in channel func-tional testing to semi-annual while actually enhancing the ability to assess operability and functionality of the leak detection system. Deletion of the obsolescent channel check increases operator, availability and can be considered a contribution towards decreasing the probability or, consequences of accidents. Semi-annual channel functional testing of the NUMAC equipment provides more margin to Allowable Values than testing the present equipment on a monthly basis. Hence, the probability or. consequences of previously evaluated accidents are not increased by this change.
- 2) Create the possibility of a new or, different kind of accident from any accident pr eviously evaluated because operability and functionality of the system is enhanced with the diagnostic self-test and drift features of the NUMAC equipment. The assessment of channel behavior is made on a 30-minute interval with the NUMAC equipment. This assessment will identify system failures and malfunction much sooner than the present 12 hour1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> manual channel check. As such, the possibility of a new or, different kind of accident due to deletion of the manual check is not credible. The semi-annual channel functional test assur es, with a large measure of conser vatism, that margins realized on monthly functional testing of the present equipment are pre-served. Again a new or, different kind of accident due to functional testing on a semi-annual ver sus monthly frequency is not credible.
- 3) Involve a significant reduction in a margin of safety because as discussed above both changes, channel check deletion and semi-annual functional test-ing, have no impact on the margin of safety. Due to the diagnostic, self-test, and channel drift features, system operability is assessed more frequently and accurately, ,failure is identified more readily, operator, efficiency is increased and presently recognized margins are conservatively preserved. The margin of safety is increased through the use of the NUMAC equipment. The diagnostic and self-test functions in lieu of a manual channel check, and semi-annual functional testing ensure the NUMAC equipment functions as intended. Hence, there is no impact to safety due to this proposal.
0 Page 5 RE()UEST FOR AMENDMENT TO TECHNICAL SPECIFICATION TABLE 4.3.2.1"1, ISOLATION ACTUATION INSTRUMENTATION SURVEILLANCE RE()UIREMENTS II As discussed above, the Supply System considers that this change does not involve a significant hazards consideraton, nor. is there a potential for signi-ficant change in the types or, significant increase in the amount of any effluents that may be released offsite, nor does it involve a significant Accor-increase in individual or cumulative occupational radiation exposure.
dingly, the proposed change meets the eligibility criteria for categorical exclusion set forth in 10CFR51.22(c)(9) and therefore, per 10CFR51.22(b), an environmental assessment of the change, is not required.
This amendment request has been reviewed and approved by the WNP-2 Plant Oper a-tions Committee (POC) and the Supply System Corporate Nuclear., Safety Review Board (CNSRB).
with the State of Washington has been provided
"
In accordance 10CFR 50.91, a copy of this letter.
Very truly yours, G. C. rensen, Manager Regulatory Programs Enclosure lw cc: JB Martin - NRC RV NS Reynolds BCP8R RB Samworth - NRC DL Williams - BPA/399 NRC Site Inspector - 901A C Eschels EFSEC
STATE OF WASHINGTON)
)
COUNTY OF BENTON )
I, G. C. Sorensen, being duly sworn, subscribe to and say that I am the Manager, Regulatory Programs, for the WASHINGTON PUBLIC POWER SUPPLY SYSTEM, the applicant herein; that I have full authority to execute this oath; that I have reviewed the foregoing; and that to the best of my knowledge, information and belief the statements made in it are true.
DATE 8 4g, 1989 G. . S9 ensen, Planager Regulatory Programs On this day personally appeared before me G. C. Sorensen to me known to be the individual who executed the foregoing instrument and acknowledged that he signed the same as his free act and deed for the uses and purposes herein mentioned.
GIVEli under s/y hand and seal this ~~day of v 1989.
otary Pu lic ~n and or tP S OF WASHINGTON Residing at j Lcr My commission expires 7 1 91
C IP I
~ 4 y g )
a 4 n