Information Notice 2012-07, Tube-to-Tube Contact Resulting in Wear in Once-Through Steam Generators: Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(Created page by program invented by StriderTol)
 
Line 14: Line 14:
| page count = 6
| page count = 6
}}
}}
{{#Wiki_filter:ML120740578 UNITED STATES NUCLEAR REGULATORY COMMISSION OFFICE OF NUCLEAR REACTOR REGULATION OFFICE OF NEW REACTORS WASHINGTON, DC  20555-0001
{{#Wiki_filter:UNITED STATES


July 17, 2012 NRC INFORMATION NOTICE 2012-07: TUBE-TO-TUBE
NUCLEAR REGULATORY COMMISSION
 
OFFICE OF NUCLEAR REACTOR REGULATION
 
OFFICE OF NEW REACTORS
 
WASHINGTON, DC 20555-0001 July 17, 2012 NRC INFORMATION NOTICE 2012-07:                 TUBE-TO-TUBE


==CONTACT==
==CONTACT==
RESULTING IN WEAR IN ONCE-THROUGH STEAM
 
===RESULTING IN===
                                                WEAR IN ONCE-THROUGH STEAM


GENERATORS
GENERATORS


==ADDRESSEES==
==ADDRESSEES==
All holders of an operating license or construction permit for a nuclear power reactor under Title 10 of the Code of Federal Regulations (10 CFR) Part 50, "Domestic Licensing of Production and Utilization Facilities," except those who have permanently ceased operations
All holders of an operating license or construction permit for a nuclear power reactor under
 
Title 10 of the Code of Federal Regulations (10 CFR) Part 50, Domestic Licensing of
 
Production and Utilization Facilities, except those who have permanently ceased operations


and have certified that fuel has been permanently removed from the reactor vessel.
and have certified that fuel has been permanently removed from the reactor vessel.


All holders of or applicants for an early site permit, standard design certification, standard design approval, manufacturing license, or combined license under 10 CFR Part 52, "Licenses, Certifications, and Approvals for Nuclear Power Plants."
All holders of or applicants for an early site permit, standard design certification, standard
 
design approval, manufacturing license, or combined license under 10 CFR Part 52, Licenses, Certifications, and Approvals for Nuclear Power Plants.


==PURPOSE==
==PURPOSE==
The U.S. Nuclear Regulatory Commission (NRC) is issuing this information notice (IN) to inform addressees of the detection of wear indications as a result of tube-to-tube contact in
The U.S. Nuclear Regulatory Commission (NRC) is issuing this information notice (IN) to inform


once-through steam generators and the lessons learned from the discovery of these indications.  These lessons learned apply to all steam generator types since they address detection of tube degradation.  It should be noted that as this IN was being written and issued, there is an on-going assessment of wear attributed to tube-to-tube contact that occurred at San Onofre Nuclear Generating Station, which uses recirculating steam generators.  The NRC expects that
addressees of the detection of wear indications as a result of tube-to-tube contact in


recipients will review the information for applicability to their facilities and consider actions, as appropriate, to avoid similar problems. Suggestions contained in this IN are not NRC requirements; therefore, no specific action or written response is required.
once-through steam generators and the lessons learned from the discovery of these indications.
 
These lessons learned apply to all steam generator types since they address detection of tube
 
degradation. It should be noted that as this IN was being written and issued, there is an
 
on-going assessment of wear attributed to tube-to-tube contact that occurred at San Onofre
 
Nuclear Generating Station, which uses recirculating steam generators. The NRC expects that
 
recipients will review the information for applicability to their facilities and consider actions, as
 
appropriate, to avoid similar problems. Suggestions contained in this IN are not NRC
 
requirements; therefore, no specific action or written response is required.


==DESCRIPTION OF CIRCUMSTANCES==
==DESCRIPTION OF CIRCUMSTANCES==
Three Mile Island, Unit 1 (TMI-1), completed the replacement of both of its original once-through steam generators in early 2010, after exiting a refueling outage that began in the fall of 2009.  AREVA (France) fabricated the replacement steam generators.  The tubes in the steam generator are straight and supported by 15 tube support plates.  The center of the tubes is located approximately 15 centimeters (6 inches) below the eighth tube support plate (between the seventh and eighth tube support plates).
Three Mile Island, Unit 1 (TMI-1), completed the replacement of both of its original once-through


The first inservice inspection of the TMI-1 replacement steam generators took place in fall 2011.  During this inspection, the TMI-1 licensee inspected 100-percent of the tubes in both steam generators with a bobbin coil probe, which is an eddy current nondestructive examination technique.  The bobbin coil probe is operated in both an absolute and differential mode. In the
steam generators in early 2010, after exiting a refueling outage that began in the fall of 2009.


differential mode, the probe is sensitive to localized variations along the length of the tube, such as cracks or pits. However, this mode is not sensitive to gradual variations along the length of the tubing.  In the absolute mode, the probe is sensitive to long and gradual changes along the length of the tubing.
AREVA (France) fabricated the replacement steam generators. The tubes in the steam


During these inspections at TMI-1, the licensee detected several tubes with indications on the absolute channel with no discernable signal being observed on the differential channel.  A comprehensive review of all of the absolute drift indications revealed that most of them were near the middle of the tube's total length (between the eighth and ninth tube support plate), were in a radial pattern approximately 76 centimeters to 114 centimeters (30 inches to 45 inches) from the center of the steam generator, and in adjacent tubes (two or three).  In addition, the indications in adjacent tubes faced each other, were at the same elevation, and had similar lengths and depths.  A more detailed investigation led the licensee to conclude that these indications are a result of tube wear due to tube-to-tube contact.  The length of these wear indications ranged from 5 centimeters to 20 centimeters (2 inches to 8 inches) and the depths ranged from 1 percent to 21 percent through-wall.
generator are straight and supported by 15 tube support plates. The center of the tubes is


As a result of these findings, the licensee for TMI-1 informed the licensee for Arkansas Nuclear One, Unit 1 (ANO-1), since ANO-1 has similar steam generators.  At the time, ANO-1 was shut down for a refueling outage.  However, the steam generator tube inspections had been completed.
located approximately 15 centimeters (6 inches) below the eighth tube support plate (between


The original once-through steam generators at ANO-1 were replaced in 2005.  AREVA (France) also fabricated the replacement once-through steam generators at ANO-1, which are similar (but not identical) to those used at TMI-1.  Based on the information provided by the licensee for TMI-1, the ANO-1 licensee reevaluated its previously recorded eddy current data and determined it had similar indications of wear as a result of tube-to-tube contact. Some of these
the seventh and eighth tube support plates).


indications were traceable to the first inservice inspection of ANO-1's steam generators in 2007.  The characteristics of the tube-to-tube wear indications at ANO-1, including the depth and length, are similar to those at TMI-1.  In addition, two neighboring tubes have wear indications in two spans rather than one at ANO-1.
The first inservice inspection of the TMI-1 replacement steam generators took place in fall 2011.


Given that these tube-to-tube wear indications were not originally classified as tube-to-tube wear, the licensee for ANO-1 performed an apparent cause evaluation. They determined several contributing factors as to why these indications were not identified: (1) the absence of a differential channel response to indicate a flaw-like condition, (2) not reporting, mischaracterizing, or deleting the absolute indications by the eddy current analysts, and (3)  
During this inspection, the TMI-1 licensee inspected 100-percent of the tubes in both steam
distractions to the analysts because of observing bowing of the tie rods used to support and connect the tube support plates.
 
generators with a bobbin coil probe, which is an eddy current nondestructive examination
 
technique. The bobbin coil probe is operated in both an absolute and differential mode. In the
 
differential mode, the probe is sensitive to localized variations along the length of the tube, such
 
as cracks or pits. However, this mode is not sensitive to gradual variations along the length of
 
the tubing. In the absolute mode, the probe is sensitive to long and gradual changes along the
 
length of the tubing.
 
During these inspections at TMI-1, the licensee detected several tubes with indications on the
 
absolute channel with no discernable signal being observed on the differential channel. A
 
comprehensive review of all of the absolute drift indications revealed that most of them were
 
near the middle of the tubes total length (between the eighth and ninth tube support plate),
were in a radial pattern approximately 76 centimeters to 114 centimeters (30 inches to 45 inches) from the center of the steam generator, and in adjacent tubes (two or three). In
 
addition, the indications in adjacent tubes faced each other, were at the same elevation, and
 
had similar lengths and depths. A more detailed investigation led the licensee to conclude that
 
these indications are a result of tube wear due to tube-to-tube contact. The length of these
 
wear indications ranged from 5 centimeters to 20 centimeters (2 inches to 8 inches) and the
 
depths ranged from 1 percent to 21 percent through-wall.
 
As a result of these findings, the licensee for TMI-1 informed the licensee for Arkansas Nuclear
 
One, Unit 1 (ANO-1), since ANO-1 has similar steam generators. At the time, ANO-1 was shut
 
down for a refueling outage. However, the steam generator tube inspections had been
 
completed.
 
The original once-through steam generators at ANO-1 were replaced in 2005. AREVA (France)
also fabricated the replacement once-through steam generators at ANO-1, which are similar
 
(but not identical) to those used at TMI-1. Based on the information provided by the licensee for
 
TMI-1, the ANO-1 licensee reevaluated its previously recorded eddy current data and
 
determined it had similar indications of wear as a result of tube-to-tube contact. Some of these
 
indications were traceable to the first inservice inspection of ANO-1s steam generators in 2007.
 
The characteristics of the tube-to-tube wear indications at ANO-1, including the depth and
 
length, are similar to those at TMI-1. In addition, two neighboring tubes have wear indications in
 
two spans rather than one at ANO-1.
 
Given that these tube-to-tube wear indications were not originally classified as tube-to-tube
 
wear, the licensee for ANO-1 performed an apparent cause evaluation. They determined
 
several contributing factors as to why these indications were not identified: (1) the absence of a
 
differential channel response to indicate a flaw-like condition, (2) not reporting, mischaracterizing, or deleting the absolute indications by the eddy current analysts, and (3)
distractions to the analysts because of observing bowing of the tie rods used to support and
 
connect the tube support plates.


Investigations into the cause of the tube-to-tube contact at ANO-1 and TMI-1 are ongoing.
Investigations into the cause of the tube-to-tube contact at ANO-1 and TMI-1 are ongoing.


In the spring of 2012, the licensee for Oconee, Unit 3 also detected wear attributed to tube-to-tube contact in their replacement once-through steam generators. These steam
In the spring of 2012, the licensee for Oconee, Unit 3 also detected wear attributed to
 
tube-to-tube contact in their replacement once-through steam generators. These steam
 
generators were designed and fabricated by Babcock and Wilcox in Canada and were installed
 
in 2004. The AREVA and Babcock and Wilcox once-through steam generators are similar, but
 
not identical. The indications of wear attributed to tube-to-tube contact at Oconee, Unit 3 are
 
generally located in the center of the tube bundle, the region of highest compression. The
 
length of the wear indications ranged from 2.5 centimeters to 23 centimeters (1 inch to
 
9 inches), and the depths ranged up to 20 percent through-wall. All but one of the indications of


generators were designed and fabricated by Babcock and Wilcox in Canada and were installed in 2004.  The AREVA and Babcock and Wilcox once-through steam generators are similar, but not identical.  The indications of wear attributed to tube-to-tube contact at Oconee, Unit 3 are generally located in the center of the tube bundle, the region of highest compression.  The length of the wear indications ranged from 2.5 centimeters to 23 centimeters (1 inch to
wear attributed to tube-to-tube contact were traceable to the first inservice inspection of the


9 inches), and the depths ranged up to 20 percent through-wall.  All but one of the indications of wear attributed to tube-to-tube contact were traceable to the first inservice inspection of the Oconee, Unit 3's steam generators in 2006. The licensee indicated that criterion used by eddy current analysts to report a tube-to-tube wear indication in prior outages was the indication had to have a voltage greater than 0.5 volts on one channel, and the indication's depth on a second channel had to measure within 10 percent of the through-wall depth measured on the first channel.  During the 2012 inspection, this criterion was changed to only require that the indication be present on the second channel.  The licensee believes the tube-to-tube contact is
Oconee, Unit 3s steam generators in 2006. The licensee indicated that criterion used by eddy


due to compression of the tubes in the region where the indications were observed.  Discussions with the steam generator manufacturer are on-going.
current analysts to report a tube-to-tube wear indication in prior outages was the indication had


The licensees for ANO-1, Oconee, Unit 3, and TMI-1 evaluated the severity of the tube-to-tube wear indications in their steam generators. These evaluations concluded that the wear indications did not compromise tube integrity (i.e., the tubes could still perform their intended function consistent with their original design and licensing basis). The licensees also concluded that they could operate until their next scheduled inspection with the wear indications left in service without compromising tube integrity.
to have a voltage greater than 0.5 volts on one channel, and the indications depth on a second channel had to measure within 10 percent of the through-wall depth measured on the first
 
channel. During the 2012 inspection, this criterion was changed to only require that the
 
indication be present on the second channel. The licensee believes the tube-to-tube contact is
 
due to compression of the tubes in the region where the indications were observed.
 
Discussions with the steam generator manufacturer are on-going.
 
The licensees for ANO-1, Oconee, Unit 3, and TMI-1 evaluated the severity of the tube-to-tube
 
wear indications in their steam generators. These evaluations concluded that the wear
 
indications did not compromise tube integrity (i.e., the tubes could still perform their intended
 
function consistent with their original design and licensing basis). The licensees also concluded
 
that they could operate until their next scheduled inspection with the wear indications left in
 
service without compromising tube integrity.


==BACKGROUND==
==BACKGROUND==
NRC IN 2002-21, "Axial Outside-Diameter Cracking Affecting Thermally Treated Alloy 600 Steam Generator Tubing," dated June 25, 2002, highlighted, in part, the importance of being alert during inspections to evidence of possible stress corrosion cracking, regardless of how long the steam generators have been operating. NRC IN 2002-21 can be found on the NRC's public Web site in the Agencywide Documents Access and Management System (ADAMS) at
NRC IN 2002-21, Axial Outside-Diameter Cracking Affecting Thermally Treated Alloy 600
Steam Generator Tubing, dated June 25, 2002, highlighted, in part, the importance of being
 
alert during inspections to evidence of possible stress corrosion cracking, regardless of how
 
long the steam generators have been operating. NRC IN 2002-21 can be found on the NRCs
 
public Web site in the Agencywide Documents Access and Management System (ADAMS) at
 
Accession No. ML021770094.


Accession No. ML021770094.  NRC IN 2003-05, "Failure to Detect Freespan Cracks in PWR [Pressurized Water Reactor] Steam Generator Tubes," dated June 5, 2003, highlighted, in part, that the bobbin coil eddy current data from the absolute channel can be helpful in detecting long freespan indications and
NRC IN 2003-05, Failure to Detect Freespan Cracks in PWR [Pressurized Water Reactor]
Steam Generator Tubes, dated June 5, 2003, highlighted, in part, that the bobbin coil eddy


observing changes in signals over time (ADAMS Accession No ML031550258).   NRC IN 2010-21, "Crack-Like Indication in the U-Bend Region of a Thermally Treated Alloy 600 Steam Generator Tube," dated October 6, 2010, highlighted, in part, difficulty in detecting new or unexpected forms of degradation (ADAMS Accession No. ML102210244).
current data from the absolute channel can be helpful in detecting long freespan indications and
 
observing changes in signals over time (ADAMS Accession No ML031550258).
 
NRC IN 2010-21, Crack-Like Indication in the U-Bend Region of a Thermally Treated Alloy 600
Steam Generator Tube, dated October 6, 2010, highlighted, in part, difficulty in detecting new
 
or unexpected forms of degradation (ADAMS Accession No. ML102210244).


==DISCUSSION==
==DISCUSSION==
Technical specifications require steam generator tubes to be inspected. Furthermore, they require licensees to perform an assessment to determine the types and locations of flaws to
Technical specifications require steam generator tubes to be inspected. Furthermore, they
 
require licensees to perform an assessment to determine the types and locations of flaws to
 
which the tubes may be susceptible, as well as to determine which inspection methods need to
 
be used and at what locations. The objective is to detect flaws of any type that may satisfy the
 
applicable tube repair criteria. Tube-to-tube contact and the resultant wearing of the tubes are
 
not expected to occur in steam generators. The reevaluation results of the eddy current data at
 
ANO-1 and Oconee Unit 3 illustrate the difficulties in identifying new or unexpected forms of
 
degradation and the importance of performing robust inspections that will detect both expected
 
and potentially new or emerging degradation mechanisms. IN 2010-21 highlighted the difficulty
 
of identifying a new form of degradation. IN 2002-21 indicated that the steam generators with


which the tubes may be susceptible, as well as to determine which inspection methods need to be used and at what locations.  The objective is to detect flaws of any type that may satisfy the applicable tube repair criteria.  Tube-to-tube contact and the resultant wearing of the tubes are not expected to occur in steam generators.  The reevaluation results of the eddy current data at ANO-1 and Oconee Unit 3 illustrate the difficulties in identifying new or unexpected forms of degradation and the importance of performing robust inspections that will detect both expected and potentially new or emerging degradation mechanisms.  IN 2010-21 highlighted the difficulty
the most severe operating conditions (e.g., operating time) may not be the first plant at which


of identifying a new form of degradation.  IN 2002-21 indicated that the steam generators with the most severe operating conditions (e.g., operating time) may not be the first plant at which degradation is observed.
degradation is observed.


The successful identification of wear because of tube-to-tube contact at TMI-1 indicates that a
The successful identification of wear because of tube-to-tube contact at TMI-1 indicates that a


comprehensive review of the locations and characteristics of all detected eddy current indications may be an effective diagnostic tool for evaluating inspection data. This comprehensive review may include plotting all locations where indications have been detected both radially within the steam generator tube bundle and axially along the tube length. It may involve reviewing all indications together or looking at subsets of various types of indications. It may also include determining the directions the indications face and plotting changes in signal amplitudes to determine if the indications are changing with time. Performance of the comprehensive review may, for example, reveal a clustering of eddy current indications or
comprehensive review of the locations and characteristics of all detected eddy current
 
indications may be an effective diagnostic tool for evaluating inspection data. This
 
comprehensive review may include plotting all locations where indications have been detected
 
both radially within the steam generator tube bundle and axially along the tube length. It may
 
involve reviewing all indications together or looking at subsets of various types of indications. It may also include determining the directions the indications face and plotting changes in signal
 
amplitudes to determine if the indications are changing with time. Performance of the
 
comprehensive review may, for example, reveal a clustering of eddy current indications or
 
another pattern that may warrant additional attention (e.g., migration of a loose part left in a
 
steam generator or the tube-to-tube wear phenomenon).
 
The ANO-1 and TMI-1 inspections highlight the importance of reviewing data from the absolute
 
channels in addition to data from the differential channels. Slowly varying flaws such as
 
long-tapered wear scars and cracks may not be detectable on the differential channels.
 
However, they may create clearly discernible signals on the absolute channel. The usefulness
 
of reviewing data from the absolute channel was discussed in IN 2003-05.
 
The indications at ANO-1 may have been characterized earlier as wear flaws if a more
 
comprehensive comparison was performed of the data obtained during the preservice and first
 
inservice inspection of the tubes. Since none of the tube-to-tube wear indications were present
 
in the preservice inspection, there was clearly a change in the eddy current data. The difficulty
 
of attributing this clear change in eddy current data to tube degradation, however, is that some
 
of this change also could be the result of operating the tubes at temperature for a cycle (i.e., the
 
first heating of the tubes) and normal test repeatability. This highlights the importance of
 
understanding the magnitude of the change in eddy current signals that typically occur as a
 
result of the first heat cycle and test repeatability so that any higher-than-normal changes can
 
be further investigated as possible indications of tube degradation.


another pattern that may warrant additional attention (e.g., migration of a loose part left in a steam generator or the tube-to-tube wear phenomenon).
The findings at Oconee Unit 3 demonstrate the importance of properly establishing the reporting


The ANO-1 and TMI-1 inspections highlight the importance of reviewing data from the absolute channels in addition to data from the differential channels.  Slowly varying flaws such as
criteria used by eddy current analysts to ensure flaws are identified. In addition, the findings at


long-tapered wear scars and cracks may not be detectable on the differential channels.  However, they may create clearly discernible signals on the absolute channel.  The usefulness of reviewing data from the absolute channel was discussed in IN 2003-05.
Oconee Unit 3 demonstrate the importance of using operating experience since the results from


The indications at ANO-1 may have been characterized earlier as wear flaws if a more comprehensive comparison was performed of the data obtained during the preservice and first inservice inspection of the tubes.  Since none of the tube-to-tube wear indications were present
TMI-1 and ANO-1 were used to target the inspections at Oconee Unit 3 to detect tube-to-tube


in the preservice inspection, there was clearly a change in the eddy current data. The difficulty of attributing this clear change in eddy current data to tube degradation, however, is that some of this change also could be the result of operating the tubes at temperature for a cycle (i.e., the first heating of the tubes) and normal test repeatability.  This highlights the importance of understanding the magnitude of the change in eddy current signals that typically occur as a
wear indications. The ANO-1 findings also highlight the importance of staying attentive to all


result of the first heat cycle and test repeatability so that any higher-than-normal changes can be further investigated as possible indications of tube degradation.
inspection results and not only focusing on specific issues.


The findings at Oconee Unit 3 demonstrate the importance of properly establishing the reporting criteria used by eddy current analysts to ensure flaws are identified.  In addition, the findings at Oconee Unit 3 demonstrate the importance of using operating experience since the results from TMI-1 and ANO-1 were used to target the inspections at Oconee Unit 3 to detect tube-to-tube wear indications.  The ANO-1 findings also highlight the importance of staying attentive to all inspection results and not only focusing on specific issues.
From a broader perspective, the ANO-1 and TMI-1 findings highlight the importance of


From a broader perspective, the ANO-1 and TMI-1 findings highlight the importance of performing comprehensive inspections of new and replacement equipment to ensure that it is performing as expected.
performing comprehensive inspections of new and replacement equipment to ensure that it is
 
performing as expected.


==CONTACT==
==CONTACT==
This IN requires no specific action or written response. Please direct any questions about this
This IN requires no specific action or written response. Please direct any questions about this
 
matter to the technical contact listed below or the appropriate Office of Nuclear Reactor
 
Regulation (NRR) project manager.
 
/RA/                                          /RA/
Laura A. Dudes, Director                      Timothy J. McGinty, Director


matter to the technical contact listed below or the appropriate Office of Nuclear Reactor Regulation (NRR) project manager.
Division of Construction Inspection          Division of Policy and Rulemaking


/RA/      /RA/
and Operational Programs                    Office of Nuclear Reactor Regulation


Laura A. Dudes, Director Timothy J. McGinty, Director Division of Construction Inspection Division of Policy and Rulemaking    and Operational Programs Office of Nuclear Reactor Regulation Office of New Reactors
===Office of New Reactors===


===Technical Contact:===
===Technical Contact:===
Kenneth J. Karwoski, NRR  301-415-2752 E-mail:  kenneth.karwoski@nrc.gov


Note: NRC generic communications can be found on the NRC public Web site, http://www.nrc.gov, under NRC Library.
===Kenneth J. Karwoski, NRR===
                      301-415-2752 E-mail: kenneth.karwoski@nrc.gov
 
Note: NRC generic communications can be found on the NRC public Web site, http://www.nrc.gov, under NRC Library.
 
ML120740578                                                      TAC ME7921 OFFICE  DE                    Tech Editor              BC:NRR/DE/ESGB      D:NRR/DE
 
NAME    KKarwoski              J Dougherty              GKulesa              PHiland
 
DATE    4/5/12 email          04/2/12 e-mail          5/14/12              5/21/12 OFFICE  BC:NRO/DE/CIB          PM:NRR/PGCB              LA:NRR/PGCB
 
NAME    DTerao                DBeaulieu                CHawes
 
DATE    5/14/12                5/21/12                  4/10/12 OFFICE  BC:NRR/PGCB            LA:NRR/PGCB              D:NRO/DCIP          D:NRR/DPR
 
NAME    KMorganButler          CHawes                  LDudes              TMcGinty


ML120740578 TAC ME7921 OFFICE DE Tech Editor BC:NRR/DE/ESGB D:NRR/DE NAME KKarwoski J Dougherty GKulesa PHiland DATE 4/5/12 email 04/2/12 e-mail 5/14/12 5/21/12 OFFICE BC:NRO/DE/CIB PM:NRR/PGCB LA:NRR/PGCB  NAME DTerao DBeaulieu CHawes  DATE 5/14/12 5/21/12 4/10/12  OFFICE BC:NRR/PGCB LA:NRR/PGCB D:NRO/DCIP D:NRR/DPR NAME KMorganButler CHawes LDudes TMcGinty OFFICE 4/16/12 4/16/12 via e-mail 7/13/12 7/16/12}}
OFFICE   4/16/12               4/16/12 via e-mail       7/13/12             7/16/12}}


{{Information notice-Nav}}
{{Information notice-Nav}}

Latest revision as of 07:47, 12 November 2019

Tube-to-Tube Contact Resulting in Wear in Once-Through Steam Generators
ML120740578
Person / Time
Issue date: 07/17/2012
From: Laura Dudes, Mcginty T
Office of New Reactors, Division of Policy and Rulemaking
To:
References
IN-2012-007
Download: ML120740578 (6)


UNITED STATES

NUCLEAR REGULATORY COMMISSION

OFFICE OF NUCLEAR REACTOR REGULATION

OFFICE OF NEW REACTORS

WASHINGTON, DC 20555-0001 July 17, 2012 NRC INFORMATION NOTICE 2012-07: TUBE-TO-TUBE

CONTACT

RESULTING IN

WEAR IN ONCE-THROUGH STEAM

GENERATORS

ADDRESSEES

All holders of an operating license or construction permit for a nuclear power reactor under

Title 10 of the Code of Federal Regulations (10 CFR) Part 50, Domestic Licensing of

Production and Utilization Facilities, except those who have permanently ceased operations

and have certified that fuel has been permanently removed from the reactor vessel.

All holders of or applicants for an early site permit, standard design certification, standard

design approval, manufacturing license, or combined license under 10 CFR Part 52, Licenses, Certifications, and Approvals for Nuclear Power Plants.

PURPOSE

The U.S. Nuclear Regulatory Commission (NRC) is issuing this information notice (IN) to inform

addressees of the detection of wear indications as a result of tube-to-tube contact in

once-through steam generators and the lessons learned from the discovery of these indications.

These lessons learned apply to all steam generator types since they address detection of tube

degradation. It should be noted that as this IN was being written and issued, there is an

on-going assessment of wear attributed to tube-to-tube contact that occurred at San Onofre

Nuclear Generating Station, which uses recirculating steam generators. The NRC expects that

recipients will review the information for applicability to their facilities and consider actions, as

appropriate, to avoid similar problems. Suggestions contained in this IN are not NRC

requirements; therefore, no specific action or written response is required.

DESCRIPTION OF CIRCUMSTANCES

Three Mile Island, Unit 1 (TMI-1), completed the replacement of both of its original once-through

steam generators in early 2010, after exiting a refueling outage that began in the fall of 2009.

AREVA (France) fabricated the replacement steam generators. The tubes in the steam

generator are straight and supported by 15 tube support plates. The center of the tubes is

located approximately 15 centimeters (6 inches) below the eighth tube support plate (between

the seventh and eighth tube support plates).

The first inservice inspection of the TMI-1 replacement steam generators took place in fall 2011.

During this inspection, the TMI-1 licensee inspected 100-percent of the tubes in both steam

generators with a bobbin coil probe, which is an eddy current nondestructive examination

technique. The bobbin coil probe is operated in both an absolute and differential mode. In the

differential mode, the probe is sensitive to localized variations along the length of the tube, such

as cracks or pits. However, this mode is not sensitive to gradual variations along the length of

the tubing. In the absolute mode, the probe is sensitive to long and gradual changes along the

length of the tubing.

During these inspections at TMI-1, the licensee detected several tubes with indications on the

absolute channel with no discernable signal being observed on the differential channel. A

comprehensive review of all of the absolute drift indications revealed that most of them were

near the middle of the tubes total length (between the eighth and ninth tube support plate),

were in a radial pattern approximately 76 centimeters to 114 centimeters (30 inches to 45 inches) from the center of the steam generator, and in adjacent tubes (two or three). In

addition, the indications in adjacent tubes faced each other, were at the same elevation, and

had similar lengths and depths. A more detailed investigation led the licensee to conclude that

these indications are a result of tube wear due to tube-to-tube contact. The length of these

wear indications ranged from 5 centimeters to 20 centimeters (2 inches to 8 inches) and the

depths ranged from 1 percent to 21 percent through-wall.

As a result of these findings, the licensee for TMI-1 informed the licensee for Arkansas Nuclear

One, Unit 1 (ANO-1), since ANO-1 has similar steam generators. At the time, ANO-1 was shut

down for a refueling outage. However, the steam generator tube inspections had been

completed.

The original once-through steam generators at ANO-1 were replaced in 2005. AREVA (France)

also fabricated the replacement once-through steam generators at ANO-1, which are similar

(but not identical) to those used at TMI-1. Based on the information provided by the licensee for

TMI-1, the ANO-1 licensee reevaluated its previously recorded eddy current data and

determined it had similar indications of wear as a result of tube-to-tube contact. Some of these

indications were traceable to the first inservice inspection of ANO-1s steam generators in 2007.

The characteristics of the tube-to-tube wear indications at ANO-1, including the depth and

length, are similar to those at TMI-1. In addition, two neighboring tubes have wear indications in

two spans rather than one at ANO-1.

Given that these tube-to-tube wear indications were not originally classified as tube-to-tube

wear, the licensee for ANO-1 performed an apparent cause evaluation. They determined

several contributing factors as to why these indications were not identified: (1) the absence of a

differential channel response to indicate a flaw-like condition, (2) not reporting, mischaracterizing, or deleting the absolute indications by the eddy current analysts, and (3)

distractions to the analysts because of observing bowing of the tie rods used to support and

connect the tube support plates.

Investigations into the cause of the tube-to-tube contact at ANO-1 and TMI-1 are ongoing.

In the spring of 2012, the licensee for Oconee, Unit 3 also detected wear attributed to

tube-to-tube contact in their replacement once-through steam generators. These steam

generators were designed and fabricated by Babcock and Wilcox in Canada and were installed

in 2004. The AREVA and Babcock and Wilcox once-through steam generators are similar, but

not identical. The indications of wear attributed to tube-to-tube contact at Oconee, Unit 3 are

generally located in the center of the tube bundle, the region of highest compression. The

length of the wear indications ranged from 2.5 centimeters to 23 centimeters (1 inch to

9 inches), and the depths ranged up to 20 percent through-wall. All but one of the indications of

wear attributed to tube-to-tube contact were traceable to the first inservice inspection of the

Oconee, Unit 3s steam generators in 2006. The licensee indicated that criterion used by eddy

current analysts to report a tube-to-tube wear indication in prior outages was the indication had

to have a voltage greater than 0.5 volts on one channel, and the indications depth on a second channel had to measure within 10 percent of the through-wall depth measured on the first

channel. During the 2012 inspection, this criterion was changed to only require that the

indication be present on the second channel. The licensee believes the tube-to-tube contact is

due to compression of the tubes in the region where the indications were observed.

Discussions with the steam generator manufacturer are on-going.

The licensees for ANO-1, Oconee, Unit 3, and TMI-1 evaluated the severity of the tube-to-tube

wear indications in their steam generators. These evaluations concluded that the wear

indications did not compromise tube integrity (i.e., the tubes could still perform their intended

function consistent with their original design and licensing basis). The licensees also concluded

that they could operate until their next scheduled inspection with the wear indications left in

service without compromising tube integrity.

BACKGROUND

NRC IN 2002-21, Axial Outside-Diameter Cracking Affecting Thermally Treated Alloy 600

Steam Generator Tubing, dated June 25, 2002, highlighted, in part, the importance of being

alert during inspections to evidence of possible stress corrosion cracking, regardless of how

long the steam generators have been operating. NRC IN 2002-21 can be found on the NRCs

public Web site in the Agencywide Documents Access and Management System (ADAMS) at

Accession No. ML021770094.

NRC IN 2003-05, Failure to Detect Freespan Cracks in PWR [Pressurized Water Reactor]

Steam Generator Tubes, dated June 5, 2003, highlighted, in part, that the bobbin coil eddy

current data from the absolute channel can be helpful in detecting long freespan indications and

observing changes in signals over time (ADAMS Accession No ML031550258).

NRC IN 2010-21, Crack-Like Indication in the U-Bend Region of a Thermally Treated Alloy 600

Steam Generator Tube, dated October 6, 2010, highlighted, in part, difficulty in detecting new

or unexpected forms of degradation (ADAMS Accession No. ML102210244).

DISCUSSION

Technical specifications require steam generator tubes to be inspected. Furthermore, they

require licensees to perform an assessment to determine the types and locations of flaws to

which the tubes may be susceptible, as well as to determine which inspection methods need to

be used and at what locations. The objective is to detect flaws of any type that may satisfy the

applicable tube repair criteria. Tube-to-tube contact and the resultant wearing of the tubes are

not expected to occur in steam generators. The reevaluation results of the eddy current data at

ANO-1 and Oconee Unit 3 illustrate the difficulties in identifying new or unexpected forms of

degradation and the importance of performing robust inspections that will detect both expected

and potentially new or emerging degradation mechanisms. IN 2010-21 highlighted the difficulty

of identifying a new form of degradation. IN 2002-21 indicated that the steam generators with

the most severe operating conditions (e.g., operating time) may not be the first plant at which

degradation is observed.

The successful identification of wear because of tube-to-tube contact at TMI-1 indicates that a

comprehensive review of the locations and characteristics of all detected eddy current

indications may be an effective diagnostic tool for evaluating inspection data. This

comprehensive review may include plotting all locations where indications have been detected

both radially within the steam generator tube bundle and axially along the tube length. It may

involve reviewing all indications together or looking at subsets of various types of indications. It may also include determining the directions the indications face and plotting changes in signal

amplitudes to determine if the indications are changing with time. Performance of the

comprehensive review may, for example, reveal a clustering of eddy current indications or

another pattern that may warrant additional attention (e.g., migration of a loose part left in a

steam generator or the tube-to-tube wear phenomenon).

The ANO-1 and TMI-1 inspections highlight the importance of reviewing data from the absolute

channels in addition to data from the differential channels. Slowly varying flaws such as

long-tapered wear scars and cracks may not be detectable on the differential channels.

However, they may create clearly discernible signals on the absolute channel. The usefulness

of reviewing data from the absolute channel was discussed in IN 2003-05.

The indications at ANO-1 may have been characterized earlier as wear flaws if a more

comprehensive comparison was performed of the data obtained during the preservice and first

inservice inspection of the tubes. Since none of the tube-to-tube wear indications were present

in the preservice inspection, there was clearly a change in the eddy current data. The difficulty

of attributing this clear change in eddy current data to tube degradation, however, is that some

of this change also could be the result of operating the tubes at temperature for a cycle (i.e., the

first heating of the tubes) and normal test repeatability. This highlights the importance of

understanding the magnitude of the change in eddy current signals that typically occur as a

result of the first heat cycle and test repeatability so that any higher-than-normal changes can

be further investigated as possible indications of tube degradation.

The findings at Oconee Unit 3 demonstrate the importance of properly establishing the reporting

criteria used by eddy current analysts to ensure flaws are identified. In addition, the findings at

Oconee Unit 3 demonstrate the importance of using operating experience since the results from

TMI-1 and ANO-1 were used to target the inspections at Oconee Unit 3 to detect tube-to-tube

wear indications. The ANO-1 findings also highlight the importance of staying attentive to all

inspection results and not only focusing on specific issues.

From a broader perspective, the ANO-1 and TMI-1 findings highlight the importance of

performing comprehensive inspections of new and replacement equipment to ensure that it is

performing as expected.

CONTACT

This IN requires no specific action or written response. Please direct any questions about this

matter to the technical contact listed below or the appropriate Office of Nuclear Reactor

Regulation (NRR) project manager.

/RA/ /RA/

Laura A. Dudes, Director Timothy J. McGinty, Director

Division of Construction Inspection Division of Policy and Rulemaking

and Operational Programs Office of Nuclear Reactor Regulation

Office of New Reactors

Technical Contact:

Kenneth J. Karwoski, NRR

301-415-2752 E-mail: kenneth.karwoski@nrc.gov

Note: NRC generic communications can be found on the NRC public Web site, http://www.nrc.gov, under NRC Library.

ML120740578 TAC ME7921 OFFICE DE Tech Editor BC:NRR/DE/ESGB D:NRR/DE

NAME KKarwoski J Dougherty GKulesa PHiland

DATE 4/5/12 email 04/2/12 e-mail 5/14/12 5/21/12 OFFICE BC:NRO/DE/CIB PM:NRR/PGCB LA:NRR/PGCB

NAME DTerao DBeaulieu CHawes

DATE 5/14/12 5/21/12 4/10/12 OFFICE BC:NRR/PGCB LA:NRR/PGCB D:NRO/DCIP D:NRR/DPR

NAME KMorganButler CHawes LDudes TMcGinty

OFFICE 4/16/12 4/16/12 via e-mail 7/13/12 7/16/12