ML20203E580
| ML20203E580 | |
| Person / Time | |
|---|---|
| Site: | LaSalle  |
| Issue date: | 10/19/1979 |
| From: | CBI NUCLEAR CO. |
| To: | |
| Shared Package | |
| ML20203E435 | List: |
| References | |
| WPS-E308-83670, NUDOCS 9802270084 | |
| Download: ML20203E580 (3) | |
Text
.,
C), '
d IDEldTIFI',
N jg w
l WF.LDING PROCEDURE SPECIFICATION WPS - E308/83670
+
l w
PnODuCT DOWNCOMER BRACING - NUCLEAR POWER PLANT go,E NO.
}
OF 3
No'R CuSiOr.iE n COMMONUEALTH EDIS01 CM DATE 10/10/3 nY
(' '
WOR < THIS DOCUMENT WITH GEN.WE LD PROCEDURE SPLC, GWPS-SMAW REFF DENCF PHOCEDURE QUAllFICATION HECORD CPECIFIC CONTnACT NO.
POSlflON THICKNE SS R ANGE POSITION THICKNE SS R ANCE 2525 V, H, OD 3/16" to 1 1/2" V,H,0,0 3/16" - 3/8" SPECif IC CONTR ACT WPS HEOulnEMENTS DASEMETAL-This welding procedure specification ASME SA 240 Type 304 (P-8, GP-1) complies with the ASME Code Section welded together.
S m er 1977.
This procedure is to be used for any a
welding with E308* electrode on the
<Qi base material listed.
d rlLLEH f/ETAL-Asus SnnCu:iCATioN NO.
SFA 5.4 LIMITATIONS:
p..
ASME CUMiHCATION:
E308*
'^#**'
^
ne inm pss Wenh M mms k 7,iSr.Ecac.'NO.
F-5 the base material listed shall not
(
exceed 350'F maximum.
h
- E309 ray be substituted for E303.
No post weld heat treatment is ELECTn.CA CnAnACTEHisuCS-required.
CunnENT:
DC PULARITY.
Electrode PosiLive No prcheat is required except as an aid oTnEm (Reverse Polarity) for removing moisture or unless the u AC>a NG " AT r ni A L-ambient temperature falls below 32#F.
When the ambient temperature falls below None Required 32 F, the plate shall be preheated warn to the hand within 3" of the point of Nane Required g
Gas -suiu. DING BACKLP CONTRACT f 34 78 CofaPOsmcN Mone More DATE
/d-/4 79 min. r tce. a A rt Required Required INITIALS r85/
CUSTO?/EH APPHOVAL- 06CO h LC 5 70'//
RELEASED BY
(
M //-M.97 CNQA SERVICES P otSTIMLO'NG SI ll I'hA HEG COnP REG cn ENWt{tNGR hh C
O QA IIY DATE a
C_.y. 2 JSV CMR LRS RF PREPARED JEB 5-5-78 hg
.}
CHECKED TJL 10-10-79 AUTnOnizEo RES 10.19-79 a
wuoo Imuc or n ncv nog s 1
9802270004 980220 l
PDR ADOCK 05000373 P
g IDE N TI F ICATION
- ,l mr. -
WEl&JN_G_PROCEDU R E SPECIFIC ATION WPs - E308/83670 nEN-2 or 3
rnooucT C0WilCOMER BRAC!flG - flVCLEAR POWER PLANT
.f custou[n C0tG10tlWEAl.TH EDISON "f* '[g*R DATE 10/10/79 SPECIFiG REQ 1st.7EMENTS (CONT)
SPECIFIC REQUIREMENTS (CONT) s Use only stainless steel brushes on this material.
Vertical passes may be deposited uphill or downhill, f.-
(
r; f
I
' /,,',k I
,W WL.100 (PAGE 2 OF 2) ilt.V f 40V 76
N
)
M Q{ '
, D (w l
iocutirication WPS-E308/83670
,.m WELOING PROCEDURE SPECIFICATION
,,'J L c Pacc so.
3 or 3
00WNCOMER BRAClhG - NUCLEAR POWER. PLANT n ov. so.
1 racover C0!'J10tiWEALTH EDIS0I' ev CMR o^Tc 10/10/79
- custout, GENERAL WELDING TECHNIQUE t
Optetion Desde Wold E l.c t e od e Current Volty Travel B.O.H.
O e.c rip tio n Ley.s Proc.
Sis e i T w ee (empel (Voltel flPM)
Sec/12" T
54-32 Stringer As SMA 3/32"O E308-15 60-100 23 26 Beads
- Reg'd I/8"D 60-100 23-26 90-55 100 60 5/32"O 100-145 23-26 90-47 3/16"O 130-230 24-27 x
4 3/32"C E303-16 60-100 19-22 80-49 108-55 1/8"D 70-110 23-26 105-57 5/32"E 110-170 24-26 92-50 3/16"E 160-240 24-27
- Vertical Uph ill welcs and overhead welds may be deposited usin[ a weave technique.
l JOINT DETAll-See contrae: drawings for opp;icsble joint details and dirnensions.
VERTICAL HORIZ0l;TAL OVERHEAD & DOWN
^
I I
l l
4 a
C..
~.
(wWh 0.u.
s we t oo
.tC
.c,e