RA-15-012, Response to Request for Additional Information - End of Relief Requests Associated with the Fourth 10-year Inservice Inspection (ISI) Interval
| ML15085A101 | |
| Person / Time | |
|---|---|
| Site: | Oyster Creek (DPR-019) |
| Issue date: | 01/29/2015 |
| From: | Jim Barstow Exelon Generation Co |
| To: | Document Control Desk, Office of Nuclear Reactor Regulation |
| References | |
| RA-15-012 | |
| Download: ML15085A101 (49) | |
Text
10 CFR 50.55a RA-15-012 January 29, 2015 U.S. Nuclear Regulatory Commission ATTN: Document Control Desk Washington, DC 20555-0001 Oyster Creek Nuclear Generating Station Renewed Facility Operating License No. DPR-16 NRC Docket No. 50-219
Subject:
Response to Request for Additional Information - End of Interval Relief Requests Associated with the Fourth 10-Year lnservice Inspection (ISi)
Interval
References:
- 1) Letter from J. Barstow {Exelon Generation Company, LLC) to U.S.
Nuclear Regulatory Commission, "End of Interval Relief Requests Associated with the Fourth 10-Year lnservice Inspection (ISi) Interval,"
dated January 7, 2014
- 2) Letter from J. G. Lamb (U.S. Nuclear Regulatory Commission) to M. J.
Pacilio (Exelon Generation Company, LLC), "Oyster Creek Nuclear Generating Station - Request for Additional Information Regarding the Fourth 10-Year Interval lnservice Inspection Program Plan Requests for Relief {TAC Nos. MF3406 and MF3407)," dated September 17, 2014
- 3) Letter from J. Barstow (Exelon Generation Company, LLC) to U.S.
Nuclear Regulatory Commission, "Response to Request for Additional Information - End of Interval Relief Requests Associated with the Fourth 10-Year lnservice Inspection (ISi) Interval," dated November 14, 2014
- 4) Letter from J. G. Lamb (U.S. Nuclear Regulatory Commission) to M. J.
Pacilio (Exelon Generation Company, LLC}, "Oyster Creek Nuclear Generating Station - Request for Additional Information Regarding the Fourth 10-Year Interval lnservice Inspection Program Plan Requests for Relief (TAC Nos. MF3406 AND MF3407)," dated January 6, 2015 In the Reference 1 letter, Exelon Generation Company, LLC {Exelon) requested relief from the American Society of Mechanical Engineers {ASME) Boiler and Pressure Vessel
{B&PV) Code,Section XI, "Rules for lnservice Inspection of Nuclear Power Plant Components." These reliefs apply to the fourth 10-year lnservice Inspection (ISi) interval, which concluded on January 14, 2013, for the Oyster Creek Nuclear Generating Station.
The fourth 10-year ISi interval complied with the ASME Boiler and Pressure Vessel Code,Section XI, 1995 Edition with 1996 Addenda.
U.S. Nuclear Regulatory Commission End of Interval Relief Requests Associated with the Fourth lnservice Inspection Interval January 29, 2015 Page 2 In the Reference 2 letter, the U.S. Nuclear Regulatory Commission requested additional information. Our response was contained in Reference 3. In the Reference 4 letter, the U.S. Nuclear Regulatory Commission requested additional information. Attached is our response.
There are no regulatory commitments in this response.
If you have any questions concerning this response, please contact Tom Loomis at (610) 765-5510.
Respectfully, James Barstow Director - Licensing & Regulatory Affairs Exelon Generation Company, LLC
Attachment:
Response to Request for Additional Information cc: Regional Administrator, Region I, USNRC USNRC Senior Resident Inspector, OCNGS Project Manager [OCNGS] USNRC
ATTACHMENT Response to Request for Additional Information
ATTACHMENT Response to Request for Additional Information Page 1 By letter dated January 7, 2014 (Agencywide Documents Access and Management System (ADAMS) Accession No. ML14028A579), as supplemented by letter dated November 14, 2014 (ADAMS Accession No. ML14321A044), Exelon Generation Company, LLC (Exelon or the licensee) submitted Requests for Relief R-44 and R-45 from the requirements of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code,Section XI for Oyster Creek Nuclear Generating Station (Oyster Creek). The requests for relief apply to the fourth 10-year inservice inspection (ISi) interval, in which the licensee adopted the 1995 Edition through the 1996 Addenda of ASME Code Section XI as the code of record.
The U.S. Nuclear Regulatory Commission (NRC) staff has reviewed the Relief Requests R-44 and R-45, and has determined that a request for additional information (RAI) is needed to complete its technical review. The NRC staff's RAls are below.
Request:
- 1) The examination limitations for ASME Code,Section XI, Examination Category B-F, Item B5.11, weld NR02 4-565D, N1 D Recirc Outlet Nozzle-to-Safe End, is discussed in the licensee's RAI response dated November 14, 2014. Attachment A40 to the licensee's submittal dated January 7, 2014, contains a sketch of this weld. However, this sketch appears to be a drawing of a cladded nozzle "set-in" design weld rather than a nozzle-to-safe end weld. Please clarify this sketch or provide another sketch clearly indicating the Item B5.11 nozzle and the safe end components. Please include cross-sectional plots showing volumetric coverage obtained with specific volumetric coverages near the inner surface, using appropriate ultrasonic wave angles and modalities. These are typically the most highly stressed regions, exposed to operating environments where service degradation would be expected to occur, should it be manifested.
The photos provided in the original submittal in Attachments A30 and A40 for the Item B5.11 welds are indecipherable. Please provide replacement images that are clear or alternative information to clarify the limitations these photos were intended to represent.
Response
Enclosure 1 contains the Examination Summary Sheets for welds NR02 4-565D (A40 in the Reference 1 submittal) and NR02 2-567A (A30 in the Reference 1 submittal). No photos were provided in Attachment A30 of Reference 1; however, the Examination Summary Report is provided.
Request:
- 2) For R-45, Examination Category B-J, Item B9.11 welds NE 5-0002, NE 5-0022A, and NG-5-D-0002, shown in Figures 2, 3, and 4, respectively, please provide cross-sectional plots showing volumetric coverage obtained with specific volumetric coverages near the inner surface, using appropriate ultrasonic wave angles and modalities.
Response
Enclosure 2 contains the Examination Summary Sheets for welds NE 5-0002, NE 5-0022A, and NG-D-0002 (Note: NG-D-0002 is the correct designation for this weld).
Enclosure 1 Examination Summary Sheets for Welds NR02 4-5650 and NR02 2-567A
Report No.:
EXAMINATION
SUMMARY
SHEET 005123 GE NUCLEAR ENERGY Site and Unit: O~ster Creek Unit 1 Component ID: NR02 4-5650 {N10}
Outage: OC1R20 NOZZLE to SAFE-END System RPV ASMECat.: 8-F ASMEltem 85.10 Aug Requirements: NIA Exams Performed Data Sheet Cal Sheet Procedure Calibration Block Examination Cert Level Date Personnel 45° / RL NIA APC-007 GE-UT-245N1 INV-185A Andre' Rachal II 02-NOY-04 45° /S NIA APC-008 GE-UT-245/V1 INV-185A Andre' Rachal II 02-NOY-04 60° / RL NIA APC-012 GE-UT-245/V1 INV-185A Yoshi Sekinuma Ill 02-NOY-04 60° / RL NIA APC-009 GE-UT-245/V1 INV-185A Andre' Rachal II 02-NOY-04 45° / RL N/A APC-010 GE-UT-245/V1 INV-185A Yoshi Sekinuma Ill 02-NOY-04 45° / s NIA APC-011 GE-UT-245N1 INV-185A Yoshi Sekinuma Ill 02-NOY-04 NIA APD-002 N/A GE-UT-245/V1 NIA Andre' Rachal II 08-NOY-04 PT N1DPT N/A GE-PT-100N4 NIA Chad Olson II 07-NOY-04 Examination Results:
During the automated ultrasonic examination of weld number NR02 4-565D (N1 D), the "SMART 2000" system recorded no indications associated with IGSCC utilizing 45°-shear wave, 45°-Refracted Longitudinal wave, and 60°-Refracted Longitudinal wave search units.
This examination was performed utilizing procedure GE-UT-245, Version 1, due the presence of OD and ID deposited corrosion resistant cladding (CRC).
- The 45° -shear wave examinations were performed from both the upstream and downstream sides of the weld, and recorded inside surface geometry, beam redirect and non-relevant indications.
- The 45°-RL wave examinations were performed from both the l4>Slream and downstream sides of the weld, and recorded inside surface geometry, interface, shear component and norrrelevant indications.
- The 60°-RL wave examinations were performed from both the upstream and downstream sides of the weld, and recorded shear component and non-relevant indications.
Downstream examinations were limited due to the Nozzle to Safe-end configuration. All scans were limited due to incomplete machining of the CRC on the OD surface. Machining of the OD surface CRC stopped near the weld centerline, and left a step approximately 0.020" to .040" in height. Reference the photo on page #19.
This examination satisfies the requirements of ASME Section XI, 1995 Edition, 1996 Addenda, and GL 88-01.
This component was examined following the guidelines of the POI document titled "Guideline for Ultrasonic Examination of Corrosion Resistant Cladding (CRC)", #PDl-GL-002, ReviSion "B" Dated January 29, ~~ Ultrasonic examination coverage requirements of Procedure GE-UT-245 were not achieved due to the geometrical configuration of the component. Coverage calculations were performed using ASME Sec XI, Appendix VIII, Supplement 10 as a base qualification for the examinations. The examination requirements of Supplement 10 are more stringent than those of Appendix Ill. Approximately 70% of the full-volume cmerage was achieved in accordance with the requirements of Supplement 10.
A liquid penetrant examination was performed prior to the ultrasonic examinations, which resulted in no recordable indications.
Previous ultrasonic examination data, reports, and drawings were reviewed prior to this summary.
Summary numbers: Auto UT-005123, PT-005122.
Ev.amination results were compared to data report R-16R-028 from 16R outage with ~ No Change These exarrinafions were performed under Worlc Order: C2007460 D Change This Summary and the folowing data sheets have been reviewed and accepted by the folowing personnel:
,\0 ~
jjjz~ ~"~ ~~,
/1-9-P~ 11-1~-D'{
itle: Date:
Reviewed By: Level: Date:
ANll Reviewed By: ~~ Page 1 of 19
Wall Thickness 11 Site:
QliTERCREEK Unit: 1 Report No.:
GE NUCLEAR ENERGY I I Profile Sheet Project: HlJl§ ~
I c
~ ~
System: Bat I Component ID Number: NR02 HHD fNtDJ Poeltion I o* I 90* I 1ao* I 210* I I ((]
[I] ~ I rn ~
~
1.600" NIA NIA Crown Height: EJJmi 2 I 1.4'0" NIA NIA '.A Crown Width: 1.r 3 I 1.4'0" I NIA I NIA I NIA I Nominal Diameter:
- ~
I NQWE UPST Component: \;/ SAF~:f.t:l.12 DNST Component:
4 I 1.840" I NIA I NIA I NIA I .
5 I UflO" I NIA I NIA I NIA I Weld Length: w.: I - FLOW ....
60° RL 60° RL 60° .RL 60° RLl
- 45°RL
- 45° RL 45° RL 45° RL 45° s 411;0 ~ 4s *s 0
45°S 45°$, 45°'RL'i .6Cl0 R.L Supplement WE.xaltllnaijon Coverage Thickness Taken fr9m..1996 D$ta
~ PIUIJobasoo Ul .Qi~
~ i:I'
~Exa Level: Date: I GE Reviewed By:
Page 02 of .1.i
~~~~~~~~-~~~~~~-'"-~~~~~~~~~~~~~~~~~~~__:G=-=-ENuc~arEnergy 45° Shear - General OVE!rview - (LKDN) NR02 4-5650 (NlD) NOZZLE TO SAFE-END
' " "'"Vu *w ;> .;> 1)1 t jllflNID ... llJ fi11 "'" '"'" A1MIY" Nlll .r .. t I .1ym1t : At1<1fy<,1"] ~:: .~~-:§Cf _ ~~
~-*~
.....aJjg PageJof ~
SUMMARY
NUMBER: OO!illl
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~---'G'-ENuc~arEnergy 45° Shear - General OvE~rview - (LKUP) lmnnVww /.i'l )l-1 D18i 111111iiM'4*m+;fom*@fl*
jlltlNlf);' / 11 :
NRQ2 4-56_50 (NlD) .
~ r*~,:-
, *'\*;;-:.........
- [2"'"*
..... .. ....._----~
NOZZLE TO SAFE-END
~,ij
~ **
..aJ~
-"' - - JI - -
"l
- ~ :.. ..... ~ &14..""' "',,
SUMMARY
NUMBER: QQ!il.Zl Page~ of li
~~~~~~~~~-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~G~E_NuclearEnergy 45° RL - General OverviE~w - (LKDN) NR02 4-5650 (NlD) NOZZLE TO SAFE-END I ....... vu
- w , * ]I) I.. 11111 NI DI' II I ' ti '-t'l11p : A11 . 1ly'l<oNIO.r
- .....11)1-1 Innnn.-~ .... .. I1111N1 l)/;.> 111pl8J i!ii;.@§
SUMMARY
NUMBER: QQ!il2l Page 2of12
~~~~~~~~-~~~~~~~~~~~~~~~~~~~~~~~~~~__:;G~ENuclearEnergy 60° RL - General OverviE~W - (LKDN) NR02 4-5650 (N10) NOZZLE TO SAFE-END
'"""'Vu*w / . ,'1)1-4 liUl~lll/111 r #iii!¥@f# .iJ..i..?SJ
..J.4J..?SJ
SUMMARY
NUMBER: OO:illl Page Zof li
~~~~~-~~~_:__~~~~~~~~~~~-----
60° RL - General l11111t1Vll'w ;>./ I.II I Overvh~w lllllNl()/ ;> 11 1
- (LKUP)
~? 4i"'W NR02 4-5650 (NlD)
. . " *:.~~.,_r
... "'-~~~* 11:* '. t~ q GE Nuclear Energy
SUMMARY
NUMBER: QQ!illl Page .a of 12
Site:
Unit: 1 GE Nuc/1ear Energy Ovster Crulc Procedure:
Version I Revision:
fl.~:f.!.[*Z.4.§.
~
System:
Weld No.:
Ultrasonic Data I Scan Parameter Sheet (Automated with Micro TomoScan)
Bf!)L t:f.89.Z. ~§§§.12 lN.112l Report No.:
Data Sheet No.:
Qgj1ZJ.
APQ.O(U Project No.: Hl9§ ORR: tfA Configuration: NOZZLe. [Q §A.Eli:&t:f.Q Calibration Sheet No.: A.PC.OOZ tlmJ. gj_z Scanner Information Weld Reference, (GE-ADM-1005): Lo: [OP DEA.Q r;e_NTER Wo: ~e.L.12 CL Motor Steps: Cir: 1H.§ Tra: Z§.QZ Examination Surface: QJ2 Exam Surface Temperature: l!l *F Thermometer SIN: mm Exam Start: gz-ti!lY~ §.:Z.§.;oo eM.
Exam End: 08-Nov-<U l.;~l.:OO AM Nominal Pipe Size: ~ N1)minal Thickness: 1...§JL Weld Width: 1..§!L Weld Length: ~
Scanner: ttm!A Track Diameter: l§JJ!L. Arm Length: 1JJl!L. Track Location: QQWN§TREA.M X Positive Scan Direction: QQMtl.ffie.AM Y Positive Scan Direction: &W I
Resolution: s~ lnd*~x Ax I Clrc: s w.r. s~ Axial Scan Speed: s M.laL~ Clrc Scan Speed: s 1.Q la.LSec, Scanner Zero Positions: CIR: me DEA.12 r;e.NTEB. , TRA: WEl.Q f;EN[gRLttte. ROT Zero: LQQKltl.fl. QQWN§'[B&AM Scan Parameters and Results Scan: Skew: Filo ID: Disk: X-Start: X-Stop: Y-Start: Y-Stop: Gain: Results: Comments:
Z1ll Q BBIJ.U2.Z1.Q S2K-D"""4.00§. rut: 1.§,£. ~ ~ LQa C.O.E,J.K 46°§.. 4.§."Rt... §Q 0 LKDN ZZQ 1JQ BBN.1..QlZ!J. S2K-D~Q£00§. rut: .u.I: Q,.Q'.'. z.£. LQa C.O.E,J,K 4.§.~. 4.§.0 8.L, §~ LKJ,lp ml .IQ BBN.1.Dm §2K-D"""4.006 ~ 1..£. Q,.Q'.'. .H..§'.'. L.Qg ~ 46"S. 4.§. 0 Bt... §Q LKCW DNS[
0
- w. .IQ BBN.112W. §2K-0"""4.00§. Q,.Q'.'. ~ Q,.Q'.'. 1§£ L.Qg ~ 46°§, 46~1... §Q 0 l.~tt: J,LPS[
Z4.Q :lQ BB/j1..lmQ §2K-D"""4.00§. ~ 1..£. Q,.Q'.'. .H..§'.'. L.Qg ~ 46°§., 4.§. 0RL, §~ LKf;'H! DN§.l ro :lQ BB!i!Ql4.1 S2K-D"""4.00§. 11..§£ :1Jl: Q,.Q'.'. .u&: LQa ~ 46°§.. 4.§.. 08.L, 80° LKCf;tt: f.LP§.T
!;MMlt:l8I!Qt:I BfiiSULI§ L&!:lliit:ll2 A - NO RECORDABLE INDICATIONS B - NON-GEOMETRIC INDICATIONS C *NON-RELEVANT INDICATIONS D *ACOUSTIC INTERFACE E
- INSIDE SURFACIE F *OUTSIDE SURFACE G - WELD DISCONTINUITY H
- ROOT GEOMETRY I
- COUNTERBORE J *SHEAR COMPONENT K
- BEAM RE-DIRECT All scans were limited due to the presence of an incomplete CRC machining of the OD surface. Machining of the OD surface CRC stopped near weld centerline, and left a step approximately 0.020" to .040" In height. Reference the photo on page ~119.
~~~ /"7 I ,
- ,, .~' CJ ~~ - 725 11/DLo?
Andre' Rachal II 08-Nov-~ ANll Review: / , , Date:
Examiner: Level: Date: Level: Date: Utility Review: Date:
Page ll of .l!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Component ID: NR02 4-5650 (N1D)
Scan Information Sheet NOZ-SE GE Nuclear Energy INV-185A Transducer Parameters:
Calibration Measured Transducer Pulse Angle Size Freq. Model Exit Point SIN Scan Mode Width MHz AX 45°RL 250ns 45* 2(15X25)mm 2.00 RTD 0.80"04-319 AX 45° Shear 333ns 45* 24X 17 mm ERip. 1.50 RTD 0.55"98-159 AX 60" RL 250ns 60" 2(15X25)mm 2.00 RTD 0.75" .03-675 CIRC 45° RL 500ns 45* 2(15X25)mm 1.00 RTD 0.75"04-331 CIRC 45° Shear 333ns 45* 24 X 17 mm Ellip. 1.50 RTD 0.55"98-158 CIRC 60° RL 500ns oo* 2(15X25)mm 1.00 RTD 0.75"04-336 Scan Information:
Temp Gauge S/N: 235195 Component Temperature: 90 °\ F Scan Size Index ~ize ~
Disk # Scan ~ .EkJQ Start stnn Start stnn Scan Index
-.30" S2K-D-04, 05 45°RL LKDN O" RRN1DZ10
-4.60" O"
86.5" O" O" S2K-D-04, 05 S2K-D-04, 05 45°S LKDN OO°RL LKDN O"
O" . . . . .
O" O"
-2.60"
-5.30" o*
0 S2K-D-04, 05 45°RL LKUP 180° RRN1DZ20 O"
2.40" O" 86.5" O"
S2K-D-04, 05 S2K-D-04, 05 45°S LKUP OO°RL LKUP 180" 180" . . . . .
O" O"
-2.60"
-5.30" S2K-D-04, 05 45°RL LKCW (UPST) 90" RRN1DZ30 O"
86.5" 3.10"
. 1.40" O" O" S2K-D-04, 05 S2K-D-04, 05 45°8 LKCW (UPST) 60°RL LKCW (UPST)
-45" 90" . . . . .
-2.60"
-5.30" O"
O" 90*
S2K-D-04, 05 45°RL LKCW (ONST) RRN10Z31 O"
86.5" O"
-3.0" O" O"
+45"
. . -2.60" S2K-D-04, 05 45°8 LKCW (0NST) O" S2K-D-04, 05 60°RL LKCW (DNST) 90"
. . . -5.30" O"
_900 S2K-D-04, 05 45°RL LKCCW (UPST) RRN1DZ40 O"
86.5" 3.00" 1.40" O" O" S2K-D-04, OS S2K-D-04, 05 45°S LKCCW (UPST)
OO°RL LKCCW (UPST)
-45"
-90* . . . . .
-2.60"
-5.30" O"
O" S2K-D-04, 05 45°RL LKCCW (ON8T) -90"
+45.
RRN1DZ41 O"
86.5"
-.54" -3.0" O" O" C'lV.nJ\;I S2K-D-04, 05 (lc;: 45°S LKCCW (DNST) 60°RL LKCCW (ONST) -90° . . . . .
-2.60"
-5.30" 0-0-
Pagel.O of 12
~-=~;;;...:;...,;;..q:==-_:;;;=-~~~~~~-Date:~l~l-~l~S~*~O~t~-
//k~fef I '
- Scan (X axis) start: CS/INC. INTERFACE Scanner Information:
GE Nuclear Energy Positive Scan Direction: Downstream Index {Y axis) start: Datum "O" ((I) Too Dead Center Positive Index Direction: Clockwise Track Diameter - 28" Scanner Arm Lenath -18" Nominal Pioe Size: 26" Cal Block "r 1.80" Weld Crown Width: 1.60" (includes butterina) Como. Min\Max = 1.48" / 1.66" Resolution: s; 0.036" Track position: Downstream Index: Ax Scan: s; 0.170" ; Circ Scan: s; 0.050" Track Bolts from bottom of SE Taper= -8.0" Max Scan Soeed Settings: Axial Scans - < 1.5" I Sec. Circ. Scans - < 1.00" I Sec.
Comments: Procedure: GE-UT-245 Ver. 1 Flow is out of Vessel FULL VOLUME EXAMINATION. CRCWELD Surface examination IS required REPORT NO's.: 005123/UTI. 005122tPTl Page 11of12 GE Reviewed by: --'-'-----...'----"='----------Date: //-9-tJr
~;::+~~~~---==---Date: l I- { ~ *0 i ANH Reviewed by: ---.1~~~£~~~~~L_ _ _Date: 11Iho!Plf l
GE Nuclear Energy LIQUID PENETRANT EXAMINATION REPORT
- site: Ovster Creek Unit 1 Project: 34705 Report Number. 005122 Sheet No.: N1DPT Weld No.: NR02 4-565D (N1Dl Configuration: Nozzle to Safe.End System: RPV Procedure No.: GE-PT-100N4 VerJRev.: ~ ORR: NIA Material: Surface Condition: Item:
CS/SS/INC. Smooth Weld-Final Technique: Cleaner Penetrant Developer Color Contrast Solvent Removable Manufacturer Maqnaf1ux M!an.nux Maqna1Jla Tharmomaler mm Brand/Type SJCC-S ~ ~
Temperature: H Batch No. ~ 02C09K 0280JK.
Black Light; &! Light Mater. NIA Blacldlght Intensity: lfAj/Nlarr' Pre Clean Method: Wiping Drying Time: 6 llinutes
, Penetrant Application Bnlshina Dwell Time: 10Minutes Penetrant Removal Wipe with dry towel Drying Time: 6Minutes Wipe with demp towel Developer Application: Spravina Developing Time: 1Minutes Indication Number: I
Description:
I Results:
!ft I NRJ I !!111 Comments:
QRAWING N!JM6!;,R: ~!;,-223-A2-1000
( - / *l c-; Jl* *'-'* 0 c.f J /\'-
I~
( Chad Ol<mn & !!. 07-Nov-64 Date ExaOl!//JI#It/#
G'E Review Level 1!L Level
~~f Date I~~ Page 12 of 19
ULTRASONIC CALIBRATION DATA SHEET
~
GE Nuclear Energy (Automated with Micro TomoScan)
Project: 34705 Repart Number. 005123 1te: Ovster Creek Unit:
1 Calibration Sheet No.: APC-007 l\Neld: NR02 4--5650 £N1Dl Procedure No.: GE-UT-245 Version : V1 ORR: NIA Instrument: RD Tech/f!.Tomo 11121~ 1.MU 2.2014 Manufacturer I Model Syslem Serial No. Acquisition Software Analysis Software Analog to Digital Convel'ter. RD Tech I EQn< ON Pulser/Receiver. RD Tech I EQn< 100 Piggy Board: RD Tech I EQn< 101 Manufac1urer I Model Menufadurer / Model Manufacturer I Model Search Unit Bm ~ Z{,15x2§1.mm ~ 46°/BL FD 1.97 .. 45* ~
Manufacturer Serial No. Element Size Freq. (MHz) Angle / Mode FS/FD: MNsured Incident lo Angle WedgeFtonl Cable: 12JRG-61 I RG-61 1BQ:.174 fZJ260' {l§.' 13' £W Type: Length No. ol lntermediate Connedors Calibration Standard: INV-116A SS/CS/INC. 1.600 .. 1.100-Serial No. Material Nominal Thiclcnes6 Measured Thickness Thermomet.er. 23619fi lli "F Couplant DemlnW!f!! ~
Serial No. Temp("F) Type Balch No.
Calibration
- A~uisition Orientation: ~ CIRC Tmebase: dB Start: 0.000 Range: §.01tsln.
Units: Half Path iType: lDNOrCH IDNQTCH Avera!jng: 1 Depth: UOln. 1.80 In.
Digitizing Frequency: 12.§ M.Hz Amplitude I dB: ~ -1Z,5 d§ AcqLisition Rate: m..tH Sweep: 1,793 In: t,793 la, Max Recurrence: ~
Probe Gain: (dB) ~ LOG Wave Mode: LQ!19.ltudlnal Scan offset: 0.000111.
Screen: ~ 25 dB Booster: Active Velocity: 0.2272 ln.fusec. Index offset: O.OOQln.
- Offset: 0.000 ln.lusec, Angle: 46.00° Field Simulator: SSRomRI!§ SIN: CAL-RHOM-015 Wedge Delay: 10.150 usec. Skew: ~
Reflector: FARSDH NIA Configuration Max Amplitude/dB: -9.1 dB NIA Channel Name: 46"RL 04-319 P1/R1 NOZ-sE Sweep: o.n2" NIA Pulser. P1 Voltage: 300V Gain: (dB) LOG NIA Receiver: 81 Width: (Ns) ~00011!
Calibration Verification Configuration: Pitc/1. Catch High Pass: None Time Dl!te Bk><;!( Operator Receiver Type: l.gg Low Pass: !:/!HJ§.
Initial 1735 02-Nov-04 INV-185A AMR Rectification: fHR!l/§.! Smoothing: 2..M!h Verffied N10 45° RL AX SCAN NOZ-St Verified 1725 07-Nov-04 CAL-RHOM-916 AMR Verified Final 1945 07-Nov-04 CAL-RHOM-916 YS
-- J
.,A ndre' Rachal II 02-Nov-04
--- I L-I (
- I'll 11,14~cd J,~
r Initial Examiner Level Date I Date rra4~~ .Ii1. //-1-&'f 1,;L .. I ,J GER . Level Date fJit.e I Page ~ of ~
ULTRASONIC CALIBRATION DATA SHEET l GE Nuclear Energy (Automated with Micro TomoScan)
Unit: Report Number: 005123
~1te : Ovster Creek 1 Project: 34705 Calibration Sheet No.: APC-008 Weld: NR02 4-565D {.N1Dl Procedure No.: GE-UT-245 Version : V1 ORR: NIA Instrument: RD Tech l M.Tomo 11121-ot 1.4R1 2.2014 Manufacturer I Model System Serial No. Acquisition Software Analysis Software Analog to Digital Converter: RD Tech I EQ.TX ON Pulser/Receiver. RD Tech I EQTX 1flQ Piggy Board: BQ. Tech / EQTX101 Menufaoturer I Model Menulllcturer I Model Manufaclurer I Model Search Unit RTD 91-169 Q..fX11lmm 1.6 MHz ~ ~ 450 0.66-Manufacturer Serial No. Element Size Freq. (M-t:Z) Angle / Mode FSIFO: Measured Incident lo Angle Wedge Front Cable: RG* 61 I RG-61 U l!.i .-114 250' I 26' I 3' ~
Type: Length No. ol lntermedlate Connedors Calibnrtion Standard: INV-115A SS / CS l llJ..C. L§!!C. ~
Serlal No. Materiel Nominal Thickness Measured Thlcli:ness Thermometer: 236116 16 "'F Couplant DemlnWatw NIA Serial No. Tamp ( °F ) Type Batch No.
Caljbration A£Quisition Orientation: gB!;. CIRC Tinebase: dB Start: 0.000 Range: 6.000tn.
Un is: Haff Path
- Type: IQ.NOTgj_ 112.fJ.OTCH Averaging: 1 Depth: 1.BO#n. 1.BOln. Digitizing Frequency: 1Z,§.Ml::a Amplitude I dB: ~ *1l,9d8 Acq uisition Rate: 262Hz Max Recurrence: 2000Hz Sweep: 1,164 In. 1,"[Mln, Probe Gain: (dB) 9d8 LOG Wave Mode: Shear Scan offset: 0.000 In.
Screen: Il!tR1l! 25 dB Booster: Inactive Velocity: 0.1240 ln.lusec. Index offset: -Z,600 In.
-- - .. ,, .Offset: .. o. 000 lr..!Jl§.ec. Angle: 45.00° Field Simulator: SSRomll!l§ SIN: CAl..*RHOM-016 Wedge Delay: 12.000 ll!ec. Skew: 0.00" Reflector: FARSDH NIA Configuration Max Amplitude/dB: *1B.6dB NIA Channel Name: 46°5 98-169 P2 NOZ-SE Sweep: 0.112- NIA Pulser: fl Voltage: 300V Gain: (dB) LOG NIA Receiver: WA Width: (Ns) 333.000ns Calibration Verification Configuration: Pulse Echo High Pass: ~
TI me Da!O? Rloclc Operator Receiver Type: l.29. Low Pass: ~
Initial 1806 02*Nov41 INV-186A AMR Rectification: !fHR!l!ilr Smoothing: z..M!1z Verified N1 D 45° S AX SCAN NOZ-SE Verified 1126 07* Nov41 CAL-RHOM.o1e AMR Verified Final 1941 01-Nov41 CAL-RHCJM.016 YS
. /)
Ytndre' Rachal II 02-Nov-04
("
I (
~ lHS*Ol-1
~~~h/I ~
Initial Examiner Level Date Date f:~~ lll Level L(-<J.,tJ'/
Date ANll Review
/
//?~
/bate/
I Page 14 of 19
ULTRASONIC CALIBRATION DATA SHEET GE Nuclear Energy (Automated with Micro TomoScan)
Oyster Creek Unit: 1 Project: 34705 Report Number. 005123 Calibration Sheet No.: APC-009 NR02 ,,,_5650 <N1DJ Procedure No.: GE*UT-245 Version : ORR: NIA Instrument: BO Tec!JluTomo 11121-09 Manufactunw I Model System Serial No.
Analog to Digital Converter: RD Teclr I EOlX ON Pulser/Receiver. RD Tech IEOTX 100 Piggy Board: RD T!Ch I EQTX 101 Manufacturer I Model Manufacturer I Model Manulacturer I Model Search Unit: B112 OU16 ?l1.liX26Jmm liM& WIRL FD 1.fl." ~ o.zr Manufacturer Serial No. Element Size Freq. {MHz) Aogle / Mode FSIFD: Meesured Incident to AntJe Wedge Front Cable: f2JRG-61 I RG-61 IRG-114 IZJ2fi!l.'lZ§.'l~' tm Type; Length No. of lnlennediale Connedorg Calibration standard: lfN.1164 SS l CSllNC.
Serial No. Material Nominal Thickness Measured ~
235196 15 9F Couplant Demit! Waf!lc ~
Serial No. Temp( *F) Type Batch No.
Calibration Acquisition Orientation: ~ ~ Tmebase: dBStart: ~ Range: 7.016 In.
Units: Half Path ID NO[gj Ill!. IDf':!.QlCH Avera!jng: 1 Depth: 1.30/n. 1.30/n. Digitizing Frequency: 12,6MHz Amplitude I dB: ~ *29.2dB Acquisition Rate: m.ta.
Max Recurrence: 1QQQ1ll Sweep: 1.193 In. 1.193 In.
Gain: (dB) '3d8 LOG Wave Mode: /.,QDJl.ltudlnal Scan offset: O,OOOh Screen: ~ 25 dB Booster: ~ Velocity: 0.2272 ln.lusec. Index offset: -6.3001D..
Offset: 0.000 ln..!usec. Angle: -~
Field Simulator: SSBomoas SIN: CAL-RHDM-016 Wedge Delay: 11.00Q usec. Skew: 0.00" Reflector: FARSDH NIA Confia uration Max Amplitude/dB: -16.ldB NIA Channel Name: 6D°RL 03-676 P3/R3 NOZ§!;.
Sweep: o.n6" NIA Pulser: P3 Voltage: 300V Gain: (dB) LOG NIA Receiver: m Width: (Ns) Z§Q,OOQ/1§.
Calibration Verification Configuration: Pf1.ch Catct! High Pass: !l!1!Jg_
Ti1Tre n...- Operator Receiver Type: LQSl Low Pass: None Initial 1760 02-Nov-IU INV-185A AMR Rectification: !!JJR9l!lL Smoothing: 1..M!:H Verified N1 D 60° RL AX SCAN NOZ-SE Vertfied 1121 07-Nov-IU AMR Verified Final 1949 01-Nov-IU AMR II 02-Nov-04 Level Date
.l.1k
._,,:o___ 1/-9-~'I Level Date Page ~ of ~
ULTRASONIC CALIBRATION DATA SHEET
~
GE Nuclear Energy (Automated with Micro TomoScan)
Unit: Report Number: 005123 IS'ite: Ovster Creek 1 Project: 34705 Calibration Sheet No.: APC-010
!Weld: NR02 4-5850 fN1DJ Procedure No.: GE*UT-245 Version : V1 ORR: NIA Instrument RD Tech/11.Tomo 11121-0I 1ART 2.2014 Manufacturer I Model System Serial No. Acquisition Software Analysls Software Analog to Digital Converter. RD Tech I EQTX n§ Pulser/Rec:efver. RD T,gr I E!il,TX 100 Piggy Board: RD Tech/EQL!Ul1 Manufacturer I Model Manufacturer I Model Manufacturer I Model Search Unit: 8112 04-.JJ1 W.lix2~tmJ. ~ 46°/BL ED 1.,u* 460 0.76" Manufacturer Serial No. Elemenl Size Freq. (Miz) Angle/Mode FS/FD: Measured Incident lo Angle Wedge Front Cable: QJBG-61 I BQ-61 I B!l:.17~ (1JZ60' !.. l6' !.. 3' Lm Type: l .e ngth No. rl lntennedillte Connedors Calibration standard: INV-116.A SS ICSUNC. 1.&<<r 1M!1.:
. Sel1al No. Material Nominal Thiclcness Measured Thiclcness Thermometer: ~ 16-F Couplant Demln ~.,.,. !@
Serial No. Temp("F) Type Batch No.
Calibration A~uisition Orientation: ~ ~ Tmebase: dB Start: 0.000 Range: 6.016111.
Units: Half Path J'ype: IDNO[CH IQ NOTCH Averaijng: 1 Depth: 1.80 In. 1.80 In.
Digitizing Frequeocy: §.26MfX Amplitude I dB: ~ -16.Sdlf!. Acquisition Rate: 36§Hz Max Recurrence: 1!!!1!J..&
Sweep: t.l99 In. 1.799111.
Probe Gain: (dB) Z!.11§ l:Q!i.
Wave Mode: l,,,.ongltudlnal Scan offset: 0.000/n.
Screen: ~ 25 dB Booster: Active Velocity: 0.2272 in.lusec. Index offset: 0.000 In.
Offset: 0,000 /n./usec. . Angle: 46.-<<r Field Simulator: SSB2111R!§ SIN: CAL-RHOM4'16 Wedge Delay: 1Z,OOO usec. Skew: 0.00° Reflector: FARSDH NIA Configuration Max Amplitude/dB: -12.2d8 NIA Channel Name: 46°RJ.04-331 P1R1 NOZ-SE Sweep: o.nr NIA Voltage:
Pulser: f.1. 300V Gain: (dB) LOG NIA Receiver: R1 Width: (Ns) ~000[1§.
Calibration Verification Configuration: Pitch Catch High Pass: !J9Dg_
Tl--
1 11 1n:,;; Date Block Operator Receiver Type: l.gg Low Pass: !J9Dg_
Initial 2239 02-Nov-04 INV-18SA YS Rectification: !fJ1R!1JiJ! Smoothing: 1MHz Verified t'.11 D 45° R!c QIRC SC~N NOZ-SE Verified 1966 07-Nov-04 CAL-RHOM-01f YS Verified Final 0732 08-Nov-04 CAL-RHDM-01! YS
~ Yoshi Sekinuma Ill 02-Nov-04 I~ , I I ( ) ':zfr ll-15~
~o~
Initial Examiner Level Date '
~~I ~! c-,,_
GE Revfe.'
iLL Level LL-'l.-of ~
Date /~ Page 16 of 19
ULTRASONIC CALIBRATION DATA SHEET GE Nuclear Energy (Automated with Micro TomoScan)
Uni: Report Number: 005123 site: 0-a!,erCreelc 1 Project: 34705 Calibration Sheet No.: APC-011 Weld: NR02 .-.5650 (!J.1Dl Procedure No.: GE-UT-245 Version : V1 ORR: NIA Instrument: RD Tech £11.Tomo 1111.1-ot UHi. 2.2014 Manufacturer I Model System Serial No. Acquisition Software Analy&ia Software Analog to Digital Converter: RD Tech I EQTX ON Pulser/Receiver: BQ Tech I ~QTX 100 Piggy Board: RD Tech £C,QTX 101 Manufecturer I Medel Manufactul'8f I Model Manufacturer I Model Search Unit: Bm .H:1H Q4x17ltmJ. L§..IJ1!g 46°/ s NIA 46* 0.66-Manufacturer Serial No. Element Size Freq. (MHz) AnglefMcde FSIFO: Measured Incident to Angla Wedge Front Cable: RG:§f. £RG-61 I RG-114 2MJ' 11§.' £ J' 1 Type: length No. d Intermediate Conneclor.I Calibration Standard: l!!Y:115A SS/CS/INC. 1M!L uoo*
Serial No. Material Nominal Thic<<ne&& Measured Thickness Thermometer: 236196 15 '"F Couplant QemlnWatw lf4 Serial No. Temp("F) Type Balch No.
Calibration A~uisition Orientation: ~ CIRC Trnebase: dB Start: 0.000 Range: §..000 !!1.
Units: Half Path lQtJ.OlCH lDNQlCH Averaging: 1 Depth: U!l..ltJ,, L.f!l..!& Digitizing Frequency: 1Z.§.MHz Amplitude I dB: ~ -1~.ldB Acquisition Rate: 366Hz Max Recurrence: ~
Sweep: t.l99 In. 1.199 la.
Probe Gain: (dB) 7dB !..Q§.
Wave Mode: Shear Scan offset: -2.600 In.
Screen: !2!JR1!1 25 dB Booster: Inactive Velocity: O. fZ.40 ln.Jusec. Index offset: 0.000/n.
- Offset: Q.000 ln./usec. Angle: ~
Field Simulator: SSRomei!§. SIN: CAL-RHDM-01§.
Wedge Delay: 12.000 usec. Skew: 0.00" Reflector: FARSDH NIA Configuration Max Amplitude/dB: -20.1 dB NIA Channel Name: 46°S98-158 P2 NOZ-sE Sweep: 0.112" NIA Pulser: P2 Voltage: ~
Gain: (dB) LOG NIA Receiver: !JiA Width: (Ns) 33if.~ll!
Calibration Verification Configuration: PutuE~ High Pass: t:ml1!l
~--
I lllR::
........ Block -r--*--*
f'l.....,,.ftv Receiver Type: J.gg Low Pass: t:ml1!l Initial 2254 02-Nov-64 INV-186A YS Rectification: !1JR!ll!lr. Smoothing: l.M!:H Verified N1 D 45° S ~IRC SC8N ~OZ-SE Verified 1963 07-Nov-<U CAL-RHOM-01li YS Verified 0733 Final 08-Nov-64 CAL-RHOM-01li YS
~
( ,)
~
oshl Sekinuma Ill 02-Nov-04 ( ~
- ~
tl-15*0c./
~ ~~.#-
u~
Level Date Date GER 1ILLevel
//"<f~pr Date ?;NII Review
~-_.....,
, ~ Page 1Z of 19
ULTRASONIC CALIBRATION DATA SHEET GE Nuclear Energy (Automated with Micro TomoScan)
Site: Oyster Creek Unt 1 Project: 34705 Report Number: 005123 Calibration Sheet No.: APC-012 Weld: NR02 4-5650 CN1DJ Procedure No.: GE-UT-245 Version: ORR: NIA Instrument
- RP Tech I uTomo 11121-0I Manufacturer I Model SY$tem Serial No. Acquisition Software Analysis son-re Analog to Oigilal Converter: RD T!Ch IE01X091 Pulser/Receiver. RD Ted1IEQD(100 Piggy Board: RD Tech I EQTX 101 Menufactur<< I Model Manufacturer I Model Manufacturer I Model Search Unit: ~ ?[16x2§J.tmi u.Ml:B. WIRL FQ0.11~ fr o.1r Serial No. Element Size Freq . ~) Angle/Mode FS/FO: Measured Incident to Angle Wedge Fron!
Cable: l2JRG-H I RG-ff IRG-174 tzl.ZM!.' I 26' l 3' Im Type: Length No. d Intermediate Connectoni Calibration Standard: INV-115A SSlCS/fNC. 1..§l!r.
Serie! No. Melerial Nominal Thicknea 23611§ as er: Couplant DemlnWlfer NIA Serial No. Temp("F) Type Batch No.
Calibration Acquisition Orientation: Trnebase: dB Start: 0.000 Range: 3.998 In.
Units: Haff Path Type: /DNOTCff IDNOTCff Averaging: 1 Depth: L21lJ!1,. ~ Digitizing Frequency:
Amplitude I dB: ~ -2§.1 dB Acquisition Rate:
Max Recurrence:
Sweep: 1.!fM In. t!fUln.
Gain: (dB) "1dB LOG Wave Mode: Longttudm_t Scan offset: -6.400 In.
Screen: ~ 25 dB Booster: Active Velocity: 0.2272 /n.lusec. Index offset: 0.000 In, Offset: 0,000 ln;/Jl!!1£. Angle: u.ooo.
Field Simulator: SS Rompas SIN: CAL-RHQM-lH6 Wedge Delay: 11.320 usec. Skew: 0.00° Reflector: FARSDH NIA Configuration Max Amplitude/dB: -11.9 dB NIA Channel Name: f.O"RI..98-233 P3/R3 NOi...sE Sweep: o.1sr NIA Pulser: P3 Voltage: 300V Gain: (dB) LOG NIA Receiver: R3 Width: (Ns) 600.QQ2(§ Calibration Verification Configuration: Pf1.ch Catch High Pass: ~
T.~ OperatlX Receiver Type: l.QSl Low Pass: tl!HI!!
Initial 2219 02.Nov-04 INV-1B6A YS Rectification: !J.!RgJil[ Smoothing: 1MHz Verified N1 D 60° RL CIRC SCAN NOZ-SE Verified 1961 07-Nov-04 CAL-RH()M.()1li YS Verified Final 0738 OB-Nov-04 CAL-RH()M.()1li YS Ill 02-Nov-04 -=-.., ~ ,I ( ~ ~ Jf-IS-04 Level Date r-oe:;;~~~~V§ ' / ~el Date *
.ilC j/~ 9-~~ ~~ /thAih Level Date A II Review ~ Page 18 of 19
~~~~~~~~~~~~~~~~~--~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Non-Machined Area f,~ , ; . ns l5itJ 0* c-n ......, w 5 M*' 5W ;..). PW!'¥'1s~z:;.u;; &** P fl ~ .. p ,
GE Nuclear Energy t _. >c;:::::
NOZZLE to SAFE-END
- ':~~~~li*at::_*
.s; v11t*f'r1n* *P* .. , .1,-= rn.,, noo 1-.i. 1 IQll+1tpcr1n,tt1+mm41.g14a11,mnn * * ._ ;, ..,. *-~!?!'*.&-*i::: ~-~~-~~-- 1::..1c.f~ *:
SUMMARY
NUMBER: QQ.5123 PAGE 12of12
Report No.:
HITACHI EXAMINATION
SUMMARY
SHEET 1R23-115 Site O~ster Creek Component ID: NR02 2-567A WELD Outage 1R23 Nozzle to Shell
~em: 212 ASME Cat.: 8-D ASME Item 83.90/83.100 Aug Req N/A E1<ams Performed Data Cal Sheet Procedure Calibration Block Exam/Oper. Cert Level Date Sheet Personnel 60° Long. 0-188 N/A GE-UT-300 Ver/Rev 10 INV-116 Clint Gauthier II 11/13/2010
- 60"--- Long. 0-187 N/A GE-UT-300 Ver/Rev 10 CAL-llW2-044 Clint Gauthier II 11/13/2010 60"Shear 0-193 N/A GEH-UT-311 Ver/Rev 16 INV-116 Jimmy Johnson II 11/13/2010 611' Shear 0-192 NIA GEH-UT-311Ver/Rev16 INV-116 Jimmy Johnson II 11/13/2010 60°Shear 0-191 N/A GEH-UT-311Ver/Rev16 INV-116 Jimmy Johnson II 11/13/2010 60" Shear 0-190 NIA GEH-UT-311Ver/Rev16 INV-116 Jimmy Johnson II 11/13/2010 45"Sheor 0-189 NIA GEH-UT-311Ver/ReN16 INV-116 Jimmy Johnson II 11113/2010 Examination Results:
Ultrasonic examination results were acceptable to the requirements of ASM E B&PV Code Section XI, 1995 Edition with Addenda through Summer 1996, os modified by the POI program description and the Federal Register, Part II, Nuclear Regulatory Commission. 10 CFR Part 50 for Category B-0 Reactor Pressure Vessel IRPVJ Assembly Welds.
Nozzle to Shell Weld - Manual transverse and parallel scans were performed from the OD surface in accordance with procedure GE-UT-300, using 60" Refracted Longitudinal IRU wave search units.
Nozzle to Shell Weld - Manual parallel scans of the inner 15%T volume were performed from the OD surface in accordance with procedure GEH-UT-311 using model voUdoted search units.
Nozzle Inner Radius - Manual Zone 1 and Zone 2A scans were performed from the OD surface plate and OD Blend Radius surfaces in accordance with procedure GEH-UT-311 using model validated search units.
Manual scanning was restricted by the nozzle configuration. proximity of the N13B nozzle, and nozzle window access limitations.
No relevant indications were recorded.
Achieved Coverage: Nozzle to Shell = 28.1%, IRS = 44%.
Examination results were compared to Data Report N/A fram; N/A D Change These examinations were performed under Wark Order. C2023090-05 0No Change This Summa/}' and the fa/lawing data sheets have been reviewed and accepted ~ the fa/lawing personnel:
RWP: 519 CQIYC -,-;-;- 11J,/o - --
Dote:
Dose: 140 mr.
Prepared By. Level: Dote: Utility Review:
"b (_ L~ 1 /ftqjto ANll ReNiew: Date: Page ~1~ of ~
- -.*----*-- *--*- -1
- HITACHI Ultrasonic Calibration and Examination Record RPV Components - EPOCH 4 Site/Unit OVster Creek O Doto Report Number: lBl1::ill Linearity Sheet !d!!!!.
Outage: 1R23 Doto Sheet Number: CH87 Procedure: GE-UT-300 Rev.: !Q ORR: !JM Calibration Block: CAL-llW2-044 Search Unit Data cs Flot .!:Q: Sigma 22BC-O!!QQ£ 21!-l"K.62'1 L Rect.
Material Size Thickness Manufacturer. Serial Number. Size I Shope:
Initial Col: 0909 Exam Start: !ill 0.7" 61)" 61)"
Col Check: ~ Exam End: 1532 Incident Point Nominal Angle: Measured Angle:
Col Check: NIA Soundsafe 07220H Couplont Botch 1:.Q.!it!! ~ long.
Final Col: !fil Frequency: Model: Mode:
.llQ!£ Z!l:.f. 84*f Thermometer Initial Col Temp. Final Col Temp: Search Unit Cable DAC Construction RG-174 9ft. Q Coble Type: Length: Connectors:
Reflector Hole Goin@ Mox Amp "W"Dim. Sweep Screen Depth IX Div.
Instrument Settings SDH M:. 1X 80% g 0.64" 3.2 Panometr[~s L Eeoch 4 031526804 IX Manufacturer/Model: Serial Number.
1X 9.215us 0.234 lnf.f!.sec. 0.8-3.0MHi; 1X i Deloy/Zero: Velocity: Narrowband Filter:
1X I ~ ~ .!Q.!!!. Sg./Med Rep Rote: Rectification: Range: Pulser.
DAC lX= 5&2dB 4000hms 0% 3.03MHz Dual Sweep 0-10 = 2.0' Depth Damping: Reject: Frequency: Mode:
Note: NIA dB difference between 3/8 and 5/8 Vee Off: Qft. Qft.
Qft.
DAC: TVG: CSC: DGS:
Exam Data for Weld: NR02 2-56lA WELD Nozzle to Shell Configuration: Calibration Verification OD Plate 2?:.! Field Simulator Block S/N: ~
Exam Surface: Component Temperature Reflector Weld Examination Exam Access ScondB Recordable Exam !18 !18 !18 Area: Indications Angle Amplitude !JM ~ !18 Goin(dB) !18 ~ !:18 1" from N138 to l!jz Tscan 73.2 tJB! 61)"
Sweep(SDI !:18 ~ ~
l"from N13B tol!jz Pscan 73.2 NRI 61)"
Acceptable Linearity performed : 1<JLPL2010 Comments: Col/Exam Date is the date of initial collbration. See coverage sheet for !Imitations. 0% Reject= Off.
Ca/lbration for near surface eKamlnation.
EKams performed a minimum <K 14 dB above reference.
Scanning limited due to N138 on top and access from bioshleld window on bottom.
I
~ Clint Gauthier !!. 11/13/2<11. 0 Dote:
Initials: Examiner level: Cal/Exam Dote: Utility Reviewed By:
--- !iM !JM *Yi.51l~- t_!/!Jjto Date:
CJJJR(:_
GE Reviewed By:
Level:
- i:;:;;__
Level:
11/1.-to Date:
ANll Reviewed By:
Page 'L of I 2-
Ultrasonic Calibration and Examination Record HITACHI RPV Components - EPOCH 4 Site/Unit Oyster Creek I l Doto Report Number: 1R23-115 Linearity Sheet: !&Ql.
Outage: 1R23 Doto Sheet Number. Q:!.!!!!
Procedure: GE-UT-l{}!J Rev.: 1Q ORR: !:JM
- -..... --. - --** **- - - - ~-
Calibration Block: INV-116 Search Unit Doto cs ll2: l.&1:. Sigma 22BC-08001 2(!-J"x.62U. Rect.
Material Size Thickness Manufacturer. Serial Number: Size I Shope:
Initial Col: Q2!§ Exam Start: 00 Col Check: Exam End: !!Z: .§2: .§2:
!iM YB Incident Point Nominal Angle: Measured Angle:
Col Check: NIA Soundsafe QfilQ!:!
Final Col: Couplont Botch 3.0MHz ~ Long.
!§£ Frequency: Model: Mode:
llilli !.ll EL Thermometer Initial Col Temp. Final Col Temp: Search Unit Coble DAC Construction RG-174 9ft. Q Coble Type: Length: Connectors:
Reflector Hole Goin Mo>< Amp "W'Dim. Sweep Screen Depth lX Div.
lnstrum!i!nt Settings ID Notch 7.87' lX ~ !M: !!11: §§ Panametrlcs I Epoch 4 031526804 lX Manufacturer/Model: Serial Number.
lX 0.8 - 3.0MHz 9.215us Q234 ln.t11.sec.
lX Deloy/Zero: Velocity: Narrowband Filter:
lX ~ Fu I/wave 25.0in. ~
Rep Rote: Rectification: Range: Pulser:
DAC lX= 71.4dB 4000hms ~ 1J!ll.1!:!! Dual Sweep 0-10 = 12.s' Depth Damping: Reject: Frequency: Mode:
Note: NIA dB difference between 3/8 and 5/8 Vee Qff;. Off: Off: Off:
DAC: 1VG: CSC: DGS:
Exam Data for Weld: NR02 2-56lA WElD Nozzle to Shell Configuration: Calibration Verification OD Plate x..t: Field Simulator Block SIN: !:JM Exam Surface: Component Temperature Reflector !iM ~
Weld Examination Exam Access Scan dB Recordable Exam ~
Area: Indications Angle Amplitude
!JM ~ ~
74.l NR/ <<I' Goin(dBl !:JM ~ !:JM 1" from NllB to 1~ Tscan Sweep(SDI !:JM !JM ~
1" from NllB to 180" Pscan 74.l NRI FU Acceptable linearity performed : 19/pt.2010 Comments: Col/E><am Date is the dote of initial oallbration. See coverage sheet for limitations. 0% Reject = Off.
Cal/brat/on for full volume eitaminatlon.
Exams performed to maintain a minimum 20% 10 roll.
Non-relevant plate segregates observed.
Scanning limited due to N1lB on top and access from bioshield window on bottom.
~ Clint Gauthier .!! W1¥2010 Dote:
Initials: Examiner level: Col/E><om Dote: Utility Reviewed By:
- -- ~ !:JM "hf~. 11{1,/Jl>
ANJI Reviewed By: Dote:
~s: Examiner Level:
,&:£_
GE Reviewed By:
~
Level:
ddo Date: Page 3 of /Z...
i
- -- ~- -* * * * ------*-*---** * ----* --*** *-. - - ** *---
Ultrasonic Calibration and Examination Record HITACHI Inner Radius Examinations - EPOCH 4 Site/Unit: Dato Report Number: 1R23-115 Linearity Sheet: L-005 Ovster Creek/ 1 Outage: Doto Sheet Number: Q:11!2 1R23 Procedure: GEH-UT-311 Rev: 16 ORR: 10-22 Calibration Doto for Block: INV-116 Search Unit Data g KBA 9!f.B!:!!!. 0.5" 11 l.C1' {.. Rect.
?12:. lil:.
Material Size Thickness Manufacturer. Serial No.: Size/Shape:
Initial Cal: m?Y E>mm Start: illQ 0.7/n. 4.S- 45*
Cal Check: P!Ld Exam End: 1424 Incident Point: Nominal Angle: Measured Angle:
Col Check: !:!i!J. ~oundsafe 07220H 1.0MHz 1l3-!!2HQQ Shear Final Col: Couplant Botch frequency: Model: Mode:
~
llQill 76" F M:.f. Search Unit Cable Thermometer Initial Cal Temp. Final Col Temp:
RG-174 12ft. Q DAC Construction Coble Type: Length: Connectors:
Reflector Depth Goin @ Mox Amp "W" Dim. Sweep Screen lX Div.
Instrument Settings ID Notch 7.87' lX 80% a5" g 7.5 Panametr/cs I Epoch 4 031572911 Manufacturer/Model: Serial No.:
lX 13.22 us 0.1281 In /Jl.sec 0.8 - 3.0MHz DAC@lX= 39.0dB Zero: Velocity: Narrowband Filter.
Auto Fu//wave ~ Sq.I Med Sweep0-10= 15.<1' Meta/Path Rep Rate: Rectification: Range: Pulser/Energy Acceptable Linearity performed: 4000hms 0% l.OMHz P1f lfJl..?.7{..2'>>.0 Damping: Reject: Frequency: Mode:
Exam Data for Component: NR022-567A WELD Off: Off: Off: Qft Nozzle to Shell DAC: TVG: CSC: DGS:
Configuration:
OD Plate 92°F Calibration Verification Exam Surface: Component Temp.
Examination Exam Rotation Wedge Scan Recordable Field Simulator Block S/N: !:!L!J.
Area Angle Angle SIN dB Indications Reflector
!:!i!J. !:!i!J. !:!i!J.
Q.:.fil: ~ ~ !:!i!J. ~ !iBJ. Amplitude NIA !:!L!J. !:!i!J.
GainldB) !:!i!J. !:!L!J. !:!i!J.
Sweep ISO) !:!L!J. !:!i!J. !:JM Comments: Col/Exam Date is the date of Initial calibration. See coverage sheet for limitations. 0% Reject .. Off.
Calibration for nozzle to vessel weld IN/VJ.
EKams performed to maintain a 20-30% FSH clad roll.
Examined r from NlJB to 180° due to limited access.
$--Jimmy_ Johnson 11 l'IJ,.13{..2010 *-- ---
Initials: Examiner: Level: Col/Exam Date: Utility Reviewed By: Date:
- CfJ/J£ lit. l/hh .1f _.r, I~ ~/:J I GE Reviewed By. Level: Date: ANll Reviewed By: Date: Page 't of ('L
- -----I ***-
Ultrasonic Calibration and Examination Record HITACHI Inner Radius Examinations - EPOCH 4 Site/Unit: Ovster Creek 1.1 Data Report Number: ~ Linearity Sheet: l-OOS Doto Sheet Number: !illQ Ou toge: 1R23 Procedure: GEIHff-311 Rev: 16 DRR: 10-22 Calibration Doto for Block: ~ Search Unit Data
~ 229' !.:E. KBA ~ t..
0.5" 111.CI' R<<t.
Material Size Thickness Manufacturer: Serial No.: Size/Shape:
Initial Col: ~ Exam Start: illQ 0.71n. fU &Q:
Col Check: !il.d Exam End: 1424 Incident Point Nominal Angle: Measured Angle:
Cal Check: !JM Soundsafe ~ 1.0MHz 113-891-600 Shear Final Cal: Couplant Botch Frequency: Model: Mode:
1859 ll!!ill 7fl' F 84*f Search Unit Cable Thermometer Initial Cal Temp. Final Cal Temp:
RG-174 12ft. Q DAC Construction Coble Type: Length: Connectors:
Reflector Depth Gain@ ]Mox Amp "W"Dim. Sweep Screen Instrument Settings lX . Div.
ID Notch !:£: lX ~ 14.9' 16.5' ZJ. £ Panametr/cs Ee,och 4 031572911 Manufacturer/Model: Serial No.:
lX 15.23us 0.1282 lnlJ!.sec 0.8-3.0MH~
DAC@lX= Zero: Velocity. Narrowband Filter:
54.5dB Auto Fullwave ~ S4/Med Sweep 0-10 = 22.!l' Meta/Path Rep Rote: Rectification: Range: Pulser/Energy 4000hms 0% 1.0MHz !!l.S.
Acceptable Linearity performed : lfi.271..2010 Damping: Reject Frequency: Mode:
Exam Doto for Component NR02 2-56/A WELD Off: Off: Off: Off:
Nozzle Inner Radius DAC: lVG: CSC: OGS:
Configuration: *-* ******-
OD Plate 92°F Cali~ration Verification Exam Surface: Component Temp.
Examination Exam Rotation Wedge Scan Recordable Field Simulator Block S/N: ~
Area Angle Angle S/N dB Indications Reflector
!:!M ~ ~
~ 60 ill&: ~ !fil NRI Amplitude !JM. ~ ~
Goin(dBI !JM. !JM. ..._.. !JM.
Sweep(SOI NIA !:!M !JM.
Comments: Col/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject = Off.
Calibration for Zone 1.
Exams performed to maintain a 20-30% FSH clad roll.
E11amlned 1" from Nl38 to 180" due to limited access.
-W- Jimm~ Johnson ll Wl!f.2010 - --
Dote:
Initials: Examiner: level: Col/Exam Dote: Utility Reviewed By:
COKGE Reviewed By.
-rSi-level:
~
Date:
1t-s1 l~
ANll Reviewed By.
1!/HJ_10 Dote:
Page S of I Z.
, HIT_.A"HI
. .* -.. ----*-~ . - *-
- .-- ... = ** == ---- =--... . .
Ultrasonic Calibration and Examination Record
===.,-*-1
.-----*-..-*- -**-..-.__L--=---------------!!!1111..
Site/Unit Oyster Creek/1 Outage: 1R23
~ Inner Radius Examinations - EPOCH 4 Data Report Number:
Data Sheet Number:
~
fill!!
Linearity Sheet: L-005
!!I._._,
Procedure: GEH-UT-311 Rev: 16 ORR: 10-22 Calibration Data for Block: l!JJt::1J§. Search Unit Data cs ~ l.:fil: KBA !!!fBf!! 0.5"" l.<r/Rect.
Material Size Thickness Manufacturer: Serial No.: Size/Shope:
Initial Cal: ~ Exam Start mQ 9:11!1 CalCheck: !:!fA. Exam End: 1424 Incident Point Nominal Angle: Measured Angle:
Cal Check: !!IA_ Soundsafe 07220H 1Ql11:!1. 113-891-600 ~
final Col; 1902 Couplont: Botch Frequency: Model: Mode:
llQ!!Z l§:..f. 84*f Search Unit Cable Thermometer Initial Cal Temp. Final Col Temp:
RG-174 R!1 Q DAC Construction Cable Type: Length: Connectors:
Reflector Depth IGoin@ Mox Amp *w* Dim. s;eep Screen Instrument Settings lX Div.
ID Notch lX Ponametrlcs I Epoch 4 031572911 Manufacturer/Model: Serial No.:
lX 15.23 us 0.1282 In lJ!.sec 0.8-3.0MHz DAC @ lX= 54.5 dB Zero: Velocity: Narrowband Filter:
Auto Fullwave ~ Sq.I Med Sweep0-10= 35.0' Meta/Path Rep Rote: Rectification: Range: Pulser/Energy Acceptable Linearity performed : 1(¥27/2010 4000hm1, ~ ~ !!LS.
Damping: Reject Frequency: Mode:
Exam Doto for Component NR02 2-567A WELD Off: Off: Qff;. Off:
Nozzle Inner Radius DAC: TVG: CSC: DGS:
Configuration: !-**---- - --- - - -- ---------;
OD Plate 92" F Calibration Verification Exam Surface: Component Temp.
Examination Exam Rotation Wedge Scan Recordable Field Simulator Block S/N: !:!8 Area Angle Angle S/N dB Indications Reflector 90.5
!:!M !:!M MY. Amplitude
~ ~
Goin(dBI ~ !:!IA.
Comments: Col/Exam Dote is the date of Initial calibration. See coverage sheet for limitations. 0% Reject= Off.
Calibration for Zone 2A.
E>1ams performed to maintain a ~30% FSH clad roll.
Calibration on 60" flat wedge. Scanned on 7<1' flat wedge per ORR 10-20 dUf! to insufficient block length.
EHamined l" from N13B to 180°.
f#IL C.11/YJ Jimmy_ Johnson !! lYJ.Jfl.(lJO ---
Initials: Examiner: Level: Col/Exam Date: Utility Reviewed By: Dote:
,{]} /!l__ 7.ZT ,d_J(J *11. £. /J.ew,o- I!/.!..Jj_ltJ I GE Reviewed By: Level: Dote: ANll Reviewed By: Dote: Page {:, of / 2-.
- ,, Hrr.
__.A"H;-__-___
.........., __ -_**-.1.___*. .. --U-ltr.~.Inner ! l *C~*1 l1i~b*;~.Examinations
-~.~.nl! ! cRadius t! l io*n**a n*d*-E*~*a*m-in*a*tl!!!!io*n*R*e*c*~-~d-*
- EPOCH 4 -...____
Site/Unit: Oyster Creek I 1 Dato Report Number: 1R23-ll5 Linearity Sheet: L-005 Doto Sheet Number: Q:1J!l.
Outage: 1R23 Procedure: GEH-UT-311 Rev: 16 ORR: 10-22 Calibration Doto for Block: INV-116 Search Unit Data cs ~ U!:. KBA 01FRP4 0.!1' 111.rJ'{.Rect Material Size Thickness Manufacturer: Serial No.: Size/Shope:
Initial Col: ~ Exam Start mQ 9.:1..l!1. fU fU Cal Check: f:1M Exam End: 1424 Incident Point: Nominal Angle: Measured Angle:
Col Check: f:1M Soundsafe 07220H 113-!!21-600 Shear Couplont; Batch Yl.11..t!l.
Final Col: 1903 Frequency: Model: Mode:
llQill l§:£ !!£.f. Search Unit Cable Thermometer Initial Col Temp. Final Col Temp:
RG-174 12ft. Q DAC Construction Coble Type: Length: Connectors:
Reflector Depth !Gain@ Max Amp ;w, Dim. Sweep I Screen I Instrument Settings 1X \ Div. j I
7.Br
! Panametrics/ Epoch 4 031572911 ID Notch lX ~ i l:1. I Manufacturer/Model Serial No.:
1 lX I I 15.23us 0.1282 In ll!.sec 0.8-3.0MH~
DAC@ lX= 54.5 dB Zero: Velocity: Narrowband Filter:
Auto Fu//wave 22.SOin. Sg. {.Med Sweep 0-10 = 22.s' Metal Path Rep Rote: Rectification: Range: Pulser/Energy Acceptable Linearity performed: 10/27/?0JO 4000hmi 0% !Q!:1.!:!1 l'1f.
Damping: Reject Frequency: Mode:
Exam Doto for Component: NR02 2-56lA WELD Off: Off: Off: Off:
Nozzle Inner Radius DAC: TVG: CSC: DGS:
Configuration: - - - -- * * - -- ****- -- *** * - - -- - - - -- - - !
ODBR 92" F Callbratian Verification Exam Surface: ComponentTemp.
Examination Exam Rotation Wedge Scan Recordable Field Simulator Block S/N: ~
Area Angle Angle S/N dB Indications Reflector
~ !:1M ~
Amplitude
~ ~ !:1M Gain(dBI
~ !:1M . !:1M f - - - - - = ....- = - . - -
Sweep(SDl ~ !:1M !lf4_
Comments: Cal/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject= Off.
Calibration for Zone 2A.
E11ams performed to maintain a ~30% FSH clad roll.
Scanned CW.
Calibration Sweep is 22.!1' metal path, Eitamlnatlon Range setting is 15.0'.
EJcamined i-from N138 to 180' due to limited access.
_jJ_ Jlmm'i_ Johnson !! 11l.Hl2a1.0 Initials: Examiner: Level: Col/Exam Date: Utility Reviewed By: Dote:
CO&L GE Reviewed By:
JiI_
Level:
tJ/Jo Dote:
-11. f,/~
- AN11 Reviewed By:
1!./!.#1a Dote:
Page 7 of IL.
Dato Report Number: 1R23-115 Linearity Sheet: ~
Site/Unit: Oyster Creek/ 1 Doto Sheet Number: D-193 Outage: J.BgJ, Procedure: GEH-UT-311 Rev: 16 ORR: l0-22 Calibration Doto for Block: INV-116 Search Unit Data KBA Q!EBe!! OS' x 1.<J'/Rect.
~ 229' l.J!l:.
Material Size Thickness Manufacturer: Serial No.: Size/Shope:
Initial Col: Exam Start 1310 0.7/n.
Col Check: Exam End: 1424 Incident Point Nominal Angle: Measured Angle:
Col Check: !:1IA Soundsafe 07220H 113-891-600 Shl!ar bQ.!1!i!
Final Col: ~
Couplont: Botch Frequency: Model: Made:
270147 ~ !M:..E Search Unit Coble Thermometer Initial Col Temp. Final Col Temp:
RG-174 12ft. Q DAC Construction Cable Type: Length: Connectors:
Reflector Depth
- Goin-@ Mox Amp "W" Dim: Sweep ** Screen ****
lX Div..
Instrument Settings ID Natch 1X Ponametrics/Epoch 4 031572911 Manufacturer/Model: Serial No.:
lX 15.23us 0J282 ia Lf!.sec 0.{},-3.0MHt; DAC @ lX= 54.5 dB Zero: Velocity: Narrowband Filter:
Auto Fullwave 22.50/n. Sq./Med Sweep 0-10 = 22S' Metal Path Rep Rote: Rectification: Range: Pulser/Energy 4000hms 0% l.OMHz !!1.§.
Acceptable Linearity periormed: 10/27/Wl.O Damping: Reject Frequency: Mode:
Exam Doto for Component: NR02 2-561A WEl.D Off: Off: Off: Off:
Nozzle Inner Radius DAC: TVG: CSC: DGS:
Configuration: f-._ __ .._ _ _.. _ __ _ _ _ _ _ _ _ __ _.._ _ _
ODBR ~ Calibration Verification Exam Surioce: Component Temp.
Examination Exam Rotation Wedge Scan Recordable Field Simulator Block S/N: !:1IA Area Angle Angle S/N dB Indications Reflector
!:!M !:1IA !:1IA
.w NRI Amplitude
!:1IA !:1IA !:1IA Goin!dBl
- *!:1IA
. !:1IA - !:@__
sweep!SDl !:1IA !:1IA ...___ !:1IA _
Comments: Cal/Exam Date is the date of initial calibration. See coverage sheet for limitations. 0% Reject"' Off.
Calibration for Zone 2A.
Exams pelformed to maintain a 20-30% FSH clad roll.
Scanned CCW.
Cal/brat/on Sweep Is 22.S' metal path, Examination Range setting is 15.0'.
Examined CWICCW r from NUB to 180" due to limited access.
_jj__ Jlmm~ Johnson !1 ll/13/2C!J.0 - -*-- -
Initials: Examiner: Level: Col/Exam Date: Utility Reviewed By: Dote:
C{)_/}£_ rrz 11&./," 1r ~JI {_~ t1/tq/10 GE Reviewed By: Level: Dote: ANll Reviewed By: Dote: Page 8 ot I 'l
e HITACHI Reactor Pressure Vessel Coverage Oyster Creek Calculation Sheet N6A - Core Spray CODE CROSS-SECTIONAL AREA TOTAL CODE COVERAGE Required Exam Percent Weld Length = 360 Area sq. in. Area Scanned of Area Weld Length Percent Exam Volume= 66.3 IRS-Scan LKCW (S4l A 7.4 7.4 11.2% 158 1.2%
IRS-Scan LKCCW {$4) A 7.4 7.4 11.2% 158 1.2%
60° P-Scan (56) A 58.9 30.5 46.0% 158 10.1%
60" T-Scan IS4l A 7.4 7.4 11.2% 158 2.4%
60° T-Scan tS6l A 58.9 39.5 59.6% 158 13.1%
~
\C C1>
~ % Total Composite Coverage=
sa. 28.1%
Rev. 0 9/23JQ5 I~ Comments A - Scanned area from 1 inch CW of nozzle N138 ON to 180°. Scanning limited due to nozzle configuration. proximity of the N13B and the N6A nozzle window configuration. Examined from the N4A nozzle window Note* Rounding methods may affect calculated values. 54-Supplement 4 underclad volume, 56-Supplement 6 volume. Weld length in degrees
fe
...n~
Oyster Creek a
tD A"
~
b 60° S4 Exam Volume= 7.4 Sq. In.
60° S6 Exam Volume = 58.9 Sq. In.
600 S4 IRS-Scan LKCW achieved =7.4 Sq. In.
600 S4 IRS-Scan LKCCW achieved = 7.4 Sq. In.
60° S6 P-Scan achieved = 30.5 Sq. In.
600 S4 T-Scan achieved= 7.4 Sq. In.
60° S6 T-Scan achieved= 39.5 Sq. In.
/
/ ct.
I 6C°T/P I 11.5" 60°P 19.6.
I ------- I 60°T I I I
I I
~
I I
11 - - - - ,
';'S lC 11) la 1~
0 Radial Plate T Norn.= 7.125" Clad T Norn.= 0.21875"
10 z
co I") 0
~
z <(
\D z
Page_li_of - It.
ManDet Nlr_PDI Oyc_Rev 6JCl.S MANUAL DETECTION NOZZLE INNER RADIUS AND BORE INSPECTION REQUIREMENTS P!ANT OYSTER CREEK PREPAREDBV S.C. MORTENSON DATE 10/25/10 NOZZLE SCAN SCAN BEAM ROTATION WEDGE Metal EXAM ZONE SURFACE AREA ANGLE OFFSET ANGLE RADIUS Path FREQ RECIRC INLET ZONEllMI PLATE 5.0"-10.0" ss.o* - +/-45° FLAT 16.9. 1.0 MHz ZONEllMI PLATE 0-14.0" 65.0° - +/-40" FLAT 27.0" 1.0MHz ZONE2AIMI PLATE 0-8.0" 70.0" - :t35° FLAT 17.2" 1.0MHz ZONE2AIMI PLATE 0-8.()" eo.o* - :!:35° FLAT 16.0" l.OMHz FEEDWATER NNWeld(MI PLATE 0 -6.5" 55.0" - :t 35.0" - 55.0' FLAT 13.4" 1.0MHz
!Zane 1 IMI PLATE 0-6.0" 60.0" - +/-40.D" FLAT 16.0" l.OMH:r ZoneZAIMI PLATE 0- 7.0" 70.0" - :1:25.0" FLAT 26.0" l.OMHz Zane2AIMI Zone 2BIMI OOBR BARREL 40"- 90" ALL 67.3° 39.0"
-- 25.4° 46.8" 2.3" FLAT 9.6" 7.4" 1.0MHz 2.0MHZ W*240 Zane31MI BARREL ALL 28.0 . 90.0° FLAT 6.1" 2.0MHz CORE SPRAY NNWeldlMI P!ATE 0. 6.5" 45.0° - :!: 35.0°
- 65.0' FLAT 10.5" 1.0MHz ZonellMI Zone2AIMI PLATE PLATE 0-7.0" 0-10.0" 60.0" 70.0" .- +/-25.0"
- 1:20.0" FLAT FLAT 16.1" 23.0" 1.0MHz l.OMHz Zone2A(Ml OOBR 50"- 90* 66.1° - 19.3° 1.6' 7.7' l.OMHz W-078 IMI MANUAL lOOC" ()oc,M"! WEDGE/ IFIXTIJREI ROTATION ANGl£ Questions on this NIR requirements sheet shaU be directed to S.C. Mortenson@ 704 577*3770
- Dlgltally *lgned by Chris Minor Chris MI n0 r ON: cn-<:hris Minor, o-GE Hitachi, ou=Nuclear Energy, omol-Chris.Minor~eom. e=US Datt: 2010.10.26 12:39'A6-G4'00' SME Review I Date Site Review I Date Pqge -1.1=... of I Z..
Enclosure 2 Examination Summary Sheets for Welds NE 5-0002, NE 5-0022A, and NG-D-0002
Report No.:
c" Site:
Outage:
GE NUCLEAR ENERGY O]tster Creek 1R20 Component ID:
EXAMINATION
SUMMARY
SHEET NE-5-0002 Safe End to Elbow (NSB)
OCR20-143 I
System lso. Cond. ASMECat.:
B-J ASME/tem 89.11 Aug Requirement: I Exams Perfonned Data Sheet Cal Sheet Procedure Calibration Block Examination Cert Level Date Personnel 45° Shear UT-190 N/A GE-PDl-UT-2 ASMEALT. Paul Vaiden II 11/13/2004 BLOCK 3908 so* RL UT-191 N/A GE-PDl-UT-2 ASMEALT. Paul Vaiden II 11/13/2004 BLOCK3908 Examination Results:
During the manual ultrasonic examination of the above referenced component, no recordable indications were detected utilizing the 45*
shear and 60°RL wave search units ..
The exam was perfo.nned from the (Downstream) Elbow side only due to the Safe-End to Elbow configuration.
50% of the Code required volume was examined.
c This examination meets the requirements of the 1995 Edition of ASME Section XI, 1996 Addenda.
Summary No. 005294.
Examination results were compared to data report ;i/!r from /Jiii outage with 0 No Change These examinations were performed under Work Order: C2007458 0 Change This Summary and the following data sheets have been reviewed and accepted by the following personnel:
(jj)~ fu;
~- uMi ---
c Prepared Level: Date: Utility Review: Date:
ANllR~
- ~~ --"/
11i1d1 Page 1 of 4 Date: - -
Ultrasonic Calibration and Examination Record GE NUCLEAR ENERGY Manual Piping and Components Report Number: 005294 Site/Unit: Or,ster Creek I 1 Data Sheet Number: UT-190 Outage: 1R20 Linearity Sheet: L-006 Calibration Data for Block ASME ALT. BLOCK 3908 Procedure: GE-PDl-UT-2 Ver I Rev: R3 ORR: NIA I
SIS Flat 1.0" Calibration Cal Time Material Size Thick Initial Cal: 1055 Search Unit Data I Soundafe 19620 Cal Check: 1146 KBA OOC6H9 0.375"1Round Couplant: Couplant batch Cal Check: NIA Manufacturer: Serial Number Size/Shape:
235141 70"F Thermometer SIN Cal Temp. Final Cal: 1245 0.25in. 45" 45" Incident Point: Nominal Angle: Measured Angle:
DAC Construction 1.5MHz ComQ:G Shear 1 Scan Direction Ax NIA NIA Frequency: Style: Mode: Elements:
Cal Reflector 1.0" Notch NIA NIA Search Unit Cable Signal Amplitude 80% ~ ~
RG-174 §: Q Signal Sweep: 7.0Dlv .ODiv .OD/v Cable Type: Length: Connectors:
Signal dB: 7.1dB .OdB .OdB Sweep 0-10 = 2.034/n Meta/Path Instrument Settings Calibration Verification Panametrics I EQoch 4 031574612 Maufacturer/Model: Serial Number:
Field Simulator Block SIN: CAL-RHOM-010 5.985us 0.1230 lnJusec. 0.8-3.0MHz Reflector FSH NIA Zero: Velocity: Narrowband Filter:
Amplitude 20"Ai NIA Gain (dB) 7.1 NIA Auto Fullwave 2.034/n Sq.I Max Sweep (SD) 5.0 NIA Rep Rate: Rectification: Range: Pulser/Energy:
I 4000hms Off 2.0MHz PIE Acceptable Linearity performed : 10/2512004 Damping: Reject: Frequency: Mode:
Exam Data for Weld: NE-5-0002 Safe End to Elbow (N5B! Exam Comments I Limitations:
II Configuration: Examinatioo was perf'nnn&d from ti1'1} DNST Elbow side c:ily I OD 84"F 235141 due to Safe End to Elbow configutatiCll.
I Exam Surface: Exam Temp. Exam Thermometer Maintained a 5% - 20% ID Roll throughout exam.
No recordable indications.
I I
Axial UPST Scan dB Recordable Exam Circ DNST Indications Angle Axial DNST 20 NRI 45*
Clrc DNST 20 NRI 45*
I I I Exam Start: 1147 Exam End: 1200 I
~
Paul Vaiden ll h/IJ{} ~ 11hsiE*1 I Initials: Examiner: Level: ~ Re'viewed By: ----- Level: Date:
II
-- 1 Initials: Examiner2: Level:
Utility Review: Date: I
~'-/./! ./ ~v I Initial Cal/Exam Date: 11113/..2004 A~ll Rejfe_;:v f Date:
Page 1 of!
I
- GE NUCLEAR ENERGY Site/Unit: O~ster Creek I 1 Outage: 1R20 Ultrasonic Calibration and Examination Record Manual Piping and Components Report Number.
Data Sheet Number:
Linearity Sheet:
005294 UT-191 L-006 Calibration Data for Block ASME ALT. BLOCK 3908 Procedure: GE-PDl-UT-2 Ver I Rev: R3 ORR: NIA SIS Flat 1.0" Calibration Cal Time Material Size Thick Initial Cal: 1100 Search Unit Data Soundsafe 19620 Cal Check: 1200 RTD 99-506 2(8x141 mmlRect Couplant: Couplant batch Cal Check: NIA Manufacturer: Serial Number Size/Shape:
235141 70"F Thermometer SIN Cal Temp. Final Cal: 1246 0.3/n. 60° 60° Incident Point: Nominal Angle: Measured Angle:
DAC Construction 2.0MHz TRLA RL i Scan Direction Ax NIA NIA Frequency: Style: Mode: Elements:
Cal Reflector 1.0" Notch NIA NIA Search Unit Cable Signal Amplitude 80% % ~
RG-174 ~ Q Signal Sweep: 7.0Div .ODiv .ODiv Cable Type: Length: Connectors:
Signal dB: 43.5dB .OdB .OdB I
Sweep 0-10= 2.849in Metal Path Instrument Settings Calibration Verification Panametrics I Er1.och 4 031574612 Maufacturer/Model: Serial Number:
Field Simulator Block SIN: CAL-RHOM-010 8.774us 0.2320 inJusec. 0.8-3.0MHz I
Reflector FSH NIA Zero: Velocity: Narrowband Filter:
Amplitude 80% NIA Gain (dB) 36.8 NIA Auto Fullwave 2.849/n Sq.I Max Sweep (SD) 5.4 NIA Rep Rate: Rectification: Range: Pulser/Energy:
4000hms Off 2.0MHz Dual Acceptable Linearity performed : 10/2512004 Damping: Reject: Frequency: Mode:
Exam Data for Weld: NE-5-0002 Safe End to Elbow (N5Bl Exam Comments I Limitations:
I I Confi guration: ExammatiiJn ~as JVJrformed from the DNST Elbow sidP only OD 84"F 235141 Idue to Safe End to Elbowconfiiguration.
Exam Surface: Exam Temp. Exam Thermometer Scanned at reference in order to maintain a 5% to 20% ID roll.
No Recordable Indications.
Axial UPST I Scan dB Recordable Exam I
Circ DNST Indications Angle Axial I DNST 43.5 NRI 60° I I
I I
Exam Start: 1201 Exam End: 1207 y
I 1
&_ Paul Vaiden !1 I lff~ ~~t i Initials: Examiner: Level: GE Reviewed By: Level: Date:
I I I
I I I
II
~
Date: !
Initials: Examiner2: Level:
I Initial Cal/Exam Date: 1111312004 t/iJ/t Y Page ~ of!
I I
I I
ANll view: Date:
I
--t 1- --v---
\...J ~ -
Wall Thickness Site: Oyster Creek Unit: 1 Report No.:
GE NUCLEAR ENERGY Profile Sheet Project: 1R20 005294
~
~ ~
System: /so. Cond.
Component ID Number: NE-5-0002 Position o* 90° 180° 270° ((]
- [!] 121 r4l @]
1 NIA NIA NIA NIA Crown Height: Flush I
2 0.88 NIA NIA NIA I Crown Width: 1.3" I
Safe End Elbow 3 0.92 NIA NIA NIA UPST Component: I DNST Component:
Nominal Diameter 10/n. I 4 0.8 NIA NIA NIA I
Weld Length: 33.50 In.
5 0.64 NIA NIA NIA FLOW.,. I T&C's taken from previous data report no. OCR19-047 dated 10/12/02.
4..
l?v. Paul Vaiden Initials: Examiner:
!1 Level:
1111312004 Date:
na-mr-GE Reviewed By:
~
~
Level:
~ Date: Utility Review: Date: ANll~~ /;zi#y Date:
Page ! of !
~*--S-it_e:_G_E_N_:-:-:-:-:-:-:-~-:-R_G_Y Report No.:
EXAMINATION
SUMMARY
SHEET OCR20-142 Component ID: NE-5-0022A Outage: 1R20 Safe End to Elbow (NSA)
System lso. Cond. ASMECat.: B-J ASME Item 89.11 Aug Requirement:
Exams Performed Data Sheet Cal Sheet Procedure Calibration Block Examination Cert Level Date Personnel 45" Shear UT-182 NIA GE-PDl-UT-2 ASME-ALT. Paul Vaiden II 11113/2004 BLOCK3908 60" RL UT-188 NIA GE-PDl-UT-2 ASMEALT. Paul Vaiden II 11/13/2004 BLOCK3908 Examination Results:
During the manual ultrasonic examination of the above referenced component, no recordable indications were detected utilizing the 45" shear and 60"RL wave search units ..
The exam was performed from the (Downstream) Elbow side only due to the Safe-End to Elbow configuration.
50% of the Code required volume was examined.
C This examination meets the requirements of the 1995 Edition of ASME Section XI, 1996 Addenda.
Summary No. 005296.
Examination results were compared to data report N/A from N/A outage with D No Change These examinations were performed under Worlc Order. C2007457 D Change This Summary and the following data sheets have been reviewed and accepted by the following personnel:
- s ;p.....-..;e
- ;p<L!!!! ~ .....~ - - - - -- --
.....~ /~
c u..e10 D*teo A~ ~~~~~~~-
Date:
11,/i1,M Date: Page 1 of 4
- GE NUCLEAR ENERGY Site/Unit: O~ster Creek I 1 Outage: 1R20 Ultrasonic Calibration and Examination Record Manual Piping and Components Report Number:
Data Sheet Number:
Linearity Sheet:
005296 UT-182 L-006 Calibration Data for Block ASME- ALT. BLOCK 3908 Procedure: GE-PDl-UT-2 Ver I Rev: R3 ORR: NIA SIS FLAT 1.0* Calibration Cal Time Material Size Thick Initial Cal: 1055 Search Unit Data Soundsafe 19620 Cal Check: 1217 KBA OOC6H9 0.375*/Round Couplant: Couplant batch Cal Check: NIA Manufacturer: Serial Number Size/Shape:
235141 70°F Thermometer SIN Cal Temp. Final Cal: 1245 0.25/n. 45° 45*
Incident Point: Nominal Angle: Measured Angle:
DAC Construction 1.5MHz Como-G Shear 1 Scan Direction Ax NIA NIA Frequency: Style: Mode: Elements:
Cal Reflector 1.0Notch NIA NIA Search Unit Cable Signal Amplitude 80% ~ ~
RG-174 !: Q Signal Sweep: 7.0D/v .ODiv .ODiv Cable Type: Length: Connectors:
Signal dB: 7.1dB .OdB .OdB Sweep 0-10 = 2.034in Meta/Path Instrument Settings Calibration Verification Panametrics I §1.och ~ 031574612 Maufacturer/Model: Serial Number:
Field Simulator Block S/N: CAL-RHOM-010 Reflector FSDH NIA I 5.985us 0.1230 lnJusec. 0.8-3.0MHz Zero: Velocity: Narrowband Filter:
Amplitude 20% NIA Gain (dB) 7.1 NIA Auto Fullwave 2.034/n Sq.I Max Sweep (SD) 5.0 NIA Rep Rate:
4000hms Rectification:
Off Range:
2.0MHz Pulser/Energy:
PIE I
Acceptable Linearity performed : 10/2512004 Damping: Reject: Frequency: Mode:
Exam Data for Weld: NE-5-0022A Safe End to Elbow (N5Al Exam Comments I Limitations:
Configuration* Examination was per~ from the DHST E~bow side Mly due to Safe Enel to Elbow configuration I OD 84°F 235141 Maintained a 5% - 20% ID Roll throughout exam.
Exam Surface: Exam Temp. Exam Thermometer I No recordable indications.
Axial UPST Scan dB Recordable Exam I Circ DNST Indications Angle AXIAL DNST 20.0 NRI 45*
- 20.0 CIRC DNST NRI 45° i
Exam Start: 1218 Exam End: 1230 I
I I JliL Paul Vaiden fl
~<8--r=
GEReVi ~sy:
~
~=- Uf'l~y' Level: ate:
Initials: Examiner: Level:
Utility Review: Date:
Initials: Examiner 2: Level:
Initial Cal/Exam Date: 1111312004 ANll~J ~/ # t*
Date:
Page .i. of!
Ultrasonic Calibration and Examination Record GE NUCLEAR ENERGY Manual Piping and Components Report Number: 005296 Site/Unit: Oyster Creek I 1 Data Sheet Number: UT-188 Outage: 1R20 Linearity Sheet: Jdl!l!
Calibration Data for Block ASME ALT. BLOCK 3908 Procedure: GE-PDl-UT-2 Ver I Rev: R3 DRR: NIA SIS FLAT 1.0* Calibration Cal Time Material Size Thick Initial Cal: 1100 Search Unit Data Soundsafe 19620 Cal Check: NIA CoupIant:
235141 Couplant batch 70"F Cal Check: NIA RTD Manufacturer:
99-506 Serial Number 2(8x14l mm!Rect Size/Shape: I Thermometer SIN Cal Temp. Final Cal: 1246 0.3 in. §.Q: 60*
Incident Point: Nominal Angle: Measured Angle:
DAC Construction 2.0MHz TRLA RL ~
Scan Direction Ax NIA NIA Frequency: Style: Mode: Elements:
Cal Reflector 1.0* Notch NIA NIA Search Unit Cable Signal Amplitude 80% ~ ~ Q RG-174 !:
Signal Sweep: 7.0Div .ODiv .ODiv Cable Type: Length: Connectors:
Signal dB: ~ .OdB .OdB Sweep <l-10 = 2.849/n Metal Path Instrument Settings Calibration Verification Panametrics I Eaocb 4 031574612 Maufacturer/Model: Serial Number:
Field Simulator Block SIN: CAL*RHOM-010 8.n4us 0.2320 in.fusee. 0.8
- 3.0 MHz ,.
Reflector FSH NIA Zero: Velocity: Narrowband Filter:
Amplitude 80% NIA Gain (dB) 36.8 NIA Auto Ful/wave 2.849 in ~g./Max Sweep (SD) 5.4 NIA Rep"Rate: Rectification: Range: Pulser/Energy:
4000hms Q 2.0MHz DUAL Acceptable Linearity performed : 10/2512004 Damping: Reject: Frequency: Mode:
Exam Data for Weld: NE-5-0022A Exam Comments I Limitations:
Safe End to Elbow (N5Al Configuration: Examination .vas perfonned kom the DNST Elbow side only I!
due to Safe End to Elbow configuration OD 84° F 235141 Scanned at teference in onler b maintain a 5% to 20% ID 101/.
Exam Surface: Exam Temp. Exam Thermometer No Recordable Indications 1
Axial UPST Scan dB Recordable Exam Circ I DNST Indications I Angle AXIAL DNST I
I 1 - - - -- - -- - l - - -- I - +--- -+--- - -- ' - ---1 Exam Start: 1210 Exam End:
I I I r?.v' Initials:
Paul Vaiden Examiner:
ll Level:
I~ "Z'L- -;,~~~
Level: ate:
Date:
Initials: Examiner 2: Level:
Initial Cal/Exam Date: 1111312004 11/1:J6'f Page ~ of!,
Date:
'-.J _/
Wall Thickness Site: Oyster Creek Unit: 1 Report No.:
GE NUCLEAR ENERGY Profile Sheet Project: 1BZJl 005296
.. .. .. . - **~** - .
~
~ 4 System: /so. Cong.
Component ID Number: NE-5-0022A Position O' 90' 180' 270' [))
1 NIA NIA NIA NIA Crown Height: FLUSH rn 121 r4l [§]
2 1 NIA NIA NIA Crown Width: 1.3"
~AFEEND ELBOW 3 0.92 NIA NIA NIA UPST Component: DNST Component:
Nominal Diameter 10/n.
4 0.8 NIA NIA NIA Weld Length: 33.~ln.
T&C's taken from previous data report no. OCR19-048 dated 10/12/02.
~ I
<i:.
I I
~v. Paul ValfJJl.n Initials: Examiner:
l1 Level:
1111312004 Date:
~8~--~~
GERevi~y: Level: Date: Utility Review: Date: ANllR~ Page !
tt/?Jft Date:
of !
,~*
Report No.:
EXAMINATION
SUMMARY
SHEET OCR20-103 GE NUCLEAR ENERGY
-, Site:
Outage:
O]lster Creek 1R20 Component ID: NG-D-0002 26" Elbow to Pie!
System Reclrc ASMECat.: B-J ASME/tem 89.11 Aug Requirement!
Exams Perfonned Data Sheet Cal Sheet Procedure Calibration Block Examination Cert Level Date Personnel 45° Shear UT-111 NIA GE-PDl-UT-2 ASMEALT. James Williams II 11/9/2004 BLOCK3908 so* Long. UT-112 N/A GE-PDl-UT-2 ASME ALT. James W illiams II 11/9/2004 BLOCK 3908 Examination Results:
During the manual ultrasonic examination of the above referenced component, no recordable indications were detected.
One-sided stainless. 50% Coverage per POI.
This examination meets the requirements of the 1995 Edition of ASME Section XI, 1996 Addenda.
c Report Number 005334 Examination results were compared to data reoort NIA from N/A Outage With D No Change These examinations were performed under Worlc Order: C2007461 0 Change This Summary and the following data sheets have been reviewed and accepted by the following personnel:
~~~~ ~/¢~r ---
c Prepared \
w~GJ Level: Date: Date:
ANll "°"" -~/ iflr Page
-1 of 4
- GE NUCLEAR ENERGY Site/Unit: O~ster Creek I 1 Outage: 1R20 Ultrasonic Calibration and Examination Record Manual Piping and Components Report Number:
Data Sheet Number:
Linearity Sheet:
005334 UT-111 L.-008 Calibration Data for Block ASME ALT. *BLOCK 3908 Procedure: GE-PDl-UT-2 Ver I Rev: R3 DRR: NIA SIS FL.AT 1.5 Calibration Cal Time Material Size Thick Initial Cal: 1300 Search Unit Data Soundsafe 19620 Cal Check: 1400 KBA OOMPXC 0.50"1Round Couplant: Couplant batch Cal Check: NIA Manufacturer: Serial Number Size/Shape:
235347 68"F Thermometer SIN Cal Temp. Final Cal: 1640 0.35 in. 45* 45" Incident Point: Nominal Angle: Measured Angle:
DAC Construction 1.5MHz Como-G Shear 1 Scan Direction Ax NIA NIA Frequency: Style: Mode: Elements:
Cal Reflector 1.5 Notch NIA NIA Search Unit Cable Signal Amplitude 80% %
RG-174 .§: Q Signal Sweep: 5.2 Div .ODlv .ODlv Cable Type: Length: Connectors:
Signal dB: 1.6dB .OdB .OdB Sweep 0-10= 4.000ln M1talPath Instrument Settings Calibration Verification Panametrics I Ee.och 4 031540306 Maufacturer/Model: Serial Number:
Field Simulator Block SIN: CAL.-RHOM-018 7.773us 0.1230 lnJusec. 0.8-3.0MHz Reflector FSDH NIA Zero: Velocity: Narrowband Filler:
Amplitude 80 NIA Gain (dB) 16.9 NIA Fixed Fullwave 4.000ln Sq.I Max Sweep (SD) 2.6 NIA I Rep Rate: Rectification: Range: Pulser/Energy:
4000hms QI[ 2.0MHz PIE Acceptable Linearity performed : 1012512004 Damping: Reject: Frequency: Mode:
Exam Data for Weld: NG-D-0002 26" Elbow to Ploe Exam Comments I Limitations:
Configuration: 145" Shear wave examination noied pravlous non-televant indications countetbore below recordable levels.
OD 70"F 235347 Exam was performed UPST due to pipe cootiguration.
Exam Surface: Exam Temp. Exam Thermometer Axial UPST Scan dB Recordable Exam Circ DNST Indications Angle UPST 17.6 NRI 45*
IJPST 17.6 NRI 45*
Exam Start: 1400 Exam End: 1445 James Williams ll Examiner: Level: GE Reviewed By: Level: Date:
Date:
Initials: Examiner 2: Level:
Initial Cal/Exam Date: 111912004 ula-M Date:
Page ~ of!
- GE NUCLEAR ENERGY Site/Unit: O~ster Creek I 1 Outage: 1R20 Ultrasonic Calibration and Examination Record Manual Piping and Components Report Number:
Data Sheet Number:
Linearity Sheet:
005334 UT-112 L-008 Calibration Data for Block ASME ALT. BLOCK 3908 Procedure: GE-PDl-UT-2 Ver I Rev: R3 ORR: NIA SIS FLAT 1.5 Calibration Cal Time I Material Size Thick Initial Cal: 1300 Search Unit Data Soundsafe 19620 Cal Check: 1446 RTD 00-343 2(10x18J mmlRect.
Couplant: Couplant batch Cal Check: NIA Manufacturer: Serial Number Size/Shape:
235347 68°F Thermometer SIN Cal Temp. Final Cal: 1640 0.4in. 60" 60" Incident Point: Nominal Angle: Measured Angle:
DAC Construction 2.0MHz TRL2-Aust Long. ~
NIA Frequency: Style: Mode: Elements:
Scan Direction A! NIA Cal Reflector 1.5 Notch NIA NIA Search Unit Cable Signal Amplitude 80% ~
RG-174 §: fl Signal Sweep: 6.0Div .ODlv .ODiv Cable Type: Length: Connectors:
Signal dB: 49.1 dB .OdB .OdB Sweep 0-10= 5.030in Meta/Path Instrument Settings Calibration Verification Panametrics I E12,och 4 031540306 Maufacturer/Model: Serial Number:
Field Simulator Block SIN: CAL-RHOM-018 8.899us 0.2259 lnJusec. 0.8-3.0MHz Reflector 2*Radius NIA Zero: Velocity: Narrowband Filter:
Amplitude 80 NIA Gain (dB) 27.6 NIA Fixed Fullwave ~ Sq.I Max Sweep (SD) 4.0 NIA Rep Rate: Rectification: Range: Pulser/Energy:
4000hms Off 2.0MHz PIE Acceptable Linearity performed : 10/2512004 Damping: Reject: Frequency: Mode:
Exam Data for Weld: NG-D-0002 2&- Elbow to P/12,e Exam Comments I Limitations:
I
. Conti guration: * ---
1 No tecon:lable indications.
OD 70"F 235347 Exam Surface: Exam Temp. Exam Thermometer Axial UPST Scan dB Recordable Exam Circ DNST Indications Angle AXIAL UPST 34 NRI 60° 1---------'-------"1----+-------1----1 Exam Start: Exam End:
James Williams !l .-w:::.-. 11Jil>)'
Examiner: Level: I GE R.,,;owed By: Level: Date:
Date:
Initials: Examiner 2: Level:
Initial CaUExam Date: 1119/2004
_u/ilfrr Page ~ of§.
Date:
'-J ' /
Wall Thickness Site: O"s[er Creek Unit: 1 Report No.:
GE NUCLEAR ENERGY Profile Sheet Project: 1R20 005334
~
~f21 4 System: Reelre Component ID Number: NG-D-0002 Position o* 90° 1eo* 270° llJ
[TI ' (41 [§]
1 1.35 NIA NIA NIA Crown Height: FLUSH 2 1.3 NIA NIA NIA Crown Width: 2.0*
ELBOW PIPE 3 1.25 NIA NIA NIA UPST Component: DNST Component:
Nominal Diameter l 26/n.
4 NIA NIA NIA NIA Weld Length: 84/n.
I
, __ t _,/
\
' /
I
' '\ /
/
' '\ \ /
I
.,.,,..t(laJ P2Ml P~l/IO(/J. l)f't7'A
~ Jamos Wl/llams Examiner:
ll Level:
11.1912004 IJate:
- ~~..z;z
- ...,./~ ,!.,.
GE Re: By:
- Level: 'Date: Utility Review: Date: ~¥ ANllireVieW Page !
1 i?Jr Date:
of !
-