ML13219A038

Email from J. Poehler to P. Purtscher, Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis

ML13219A038
Person / Time
Site:	Vermont Yankee
Issue date:	02/15/2012
From:	Poehler J C Office of Nuclear Reactor Regulation
To:	Purtscher P T NRC/NRR/DE/EVIB
References
FOIA/PA-2013-0139
Download: ML13219A038 (2)

Text

Poehler, Jeffrey 1(1From: Poehler, Jeffrey i C.Sent: Wednesday, February 15, 2012 9:57 AMTo: Purtscher, Patrick

Subject:

RE: Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis (ME6248)Thanks,Jeffrey C. PoehlerSr. Materials EngineerNRR/DE/EVIB (301) 415-8353From: Purtscher, Patrick Sent: Wednesday, Februarý1, 2012 9:57 AMTo: Poehler, Jeffrey

Subject:

RE: Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis (ME6248)I think the rewording is appropriate.

I don't have any other issues.PatFrom: Poehler, JeffreySent: Wednesday, February 15, 2012 9:54 AMTo: Purtscher, PatrickCc: Cheruvenki, Ganesh

Subject:

RE: Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis (ME6248)Any comments on my changes?Jeffrey C. PoehlerSr. Materials EngineerNRR/DE/EVIB (301) 415-8353From: Poehler, JeffreySent: Tuesday, February 14, 2012 3:34 PMTo: Purtscher, Patrick

Subject:

RE: Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis (ME6248)Pat, the whole 15' paragraph of Section 3.2.1 could be clearer.

I reworded this paragraph to eliminate someunnecessary details.I fixed footnote 2.For Figure H-7, I agree that the lower bound could be higher at 0.1 dpa especially if you only considered thedata points that are Type 304. However, I'm not sure if the 75% would work with the stress analysis forVYNPS since they determined 14% relaxation.

The stress analysis only showed 13% margin over the ASMECode allowable for some scenarios.

I'm not sure an additional 11% of preload reduction would result in a one-to-one reduction in the percent margin, but would definitely reduce it. At any rate, Figure H-7 is just one datapoint supporting VYNPS's estimate.

If you look at the GEH curve, it is also a best-estimate curve.10aI Please review the changes which are marked up in the attached revision.

Thanks,JeffFrom: Purtscher, PatrickSent: Tuesday, February 14, 2012 1:53 PMTo: Poehler, Jeffrey

Subject:

RE: Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis (ME6248)Jeff,The 3rd sentence in Section 3.2.1 doesn't seem clear enough for the reader, I think it needs rewording.

Footnote 2, don't you mean displacement per atom?Regarding Figure H-7 from MRP-175, I looked at it and I think 75% is a realistic lower bound, still better thanthe 50% line that is drawn, but more relaxation than the mean value. Would that 25% relaxation be a problembased on what we know?PatFrom: Poehler, JeffreySent: Tuesday, February 14, 2012 9:25 AMTo: Cheruvenki, GaneshCc: Purtscher, Patrick

Subject:

RE: Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis (ME6248)Did you guys have time to comment?From: Cheruvenki, GaneshSent: Tuesday, February 07, 2012 12:07 PMTo: Poehler, Jeffrey

Subject:

RE: Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis (ME6248)Will do.From: Poehler, JeffreySent: Tuesday, February 07, 2012 10:45 AMTo: Cheruvenki, GaneshCc: Purtscher, Patrick

Subject:

Peer Review of SE Input for Vermont Yankee Core Plate Bolt Analysis (ME6248)Ganesh,As discussed yesterday, please peer review (technical only) my SE input for Vermont Yankee. Use TACME6248. Note that it is not a complete SE because Pani has the lead on the SE. He can integrate my inputsinto the structure of his SE.If you can give me comments by the end of the week that would be fine.Pat, I copied you so if you have time to review your comments would also be appreciated.

11