NRC Generic Letter 1980-05
| ML031350283 | |
| Person / Time | |
|---|---|
| Issue date: | 01/14/1980 |
| From: | Grier B NRC Region 1 |
| To: | |
| References | |
| -nr, BL-79-001B GL-80-005, NUDOCS 8001290369 | |
| Download: ML031350283 (45) | |
LfL
UNITED STATES
NUCLEA*'REGULATORY COMMISSION
REGION I
631 PARK AVENUE OL - go-_g KING OF PRUSSIA, PENNSYLVANIA 19406 Docket Nos. 50-03
50-247 JAN 1 4 1980
Consolidated Edison Company of New York, Inc.
ATTN: Mr. W. J. Cahill, Jr.
Vice President
4 Irving Place New York, New York 10003 Gentlemen:
Enclosed is IE Bulletin 79-OIB which requires action by you with regard to your power reactor facility with an operating license.
Should you have questions regarding this Bulletin or the actions required of you, please contact this office.
Sincerely, Boyce H. Grier Director Enclosures:
1 IE Bulletin No.79-01B with Attachments
2. List of Recently Issued IE Bulletins
CONTACT
- S. 0. Ebneter
(215-337-5296)
cc w/encls:
L. 0. Brooks, Project Manager, IP Nuclear W. Monti, Manager - Nuclear Power Generation Department M. Shatkouski, Plant Manager J. M. Makepeace, Director, Technical Engineering W. D. Hamlin, Assistant to Resident Manager (PASNY)
J. 0. Block, Esquire, Executive Vice President - Administration Joyce P. Davis, Esquire
80012 90
Aw
-
ENCLOSURE 1 UNITED STATES SSINS No.: 6820
NUCLEAR REGULATORY COMMISSION Accessions No.:
OFFICE OF INSPECTION AND ENFORCEMENT 7910250528 WASHINGTON, D.C. 20555 IE Bulletin No. 79-O1B
Date: January 14, 1980 ENVIRONMENTAL QUALIFICATION OF CLASS IE EQUIPMENT
Description of Circumstances
IE Bulletin No. 79-01 required the licensee to perform a detailed review of the environmental qualification of Class IE electrical equipment to ensure that the equipment will function under (i.e. during and following) postulated accident conditions.
The NRC staff has completed the initial review of licensees' responses to Bulletin No. 79-01. Based on this review, additional information is needed to facilitate completion of the NRC evaluation of the adequacy of environmental qualification of Class IE electrical equipment in the operating facilities.
In addition to requesting more detailed information, the scope of this Bulletin is expanded to resolve safety concerns relating to design basis environments and current qualification criteria not addressed in the facilities' FSARS.
These include high energy line breaks (HELB) inside and outside primary contain- ment, aging, and submergence.
Attachment 4, "GUIDELINES FOR EVALUATING ENVIRONMENTAL QUALIFICATION OF CLASS
IE ELECTRICAL EQUIPMENT IN OPERATING REACTORS", provides the guidelines and criteria the staff will use in evaluating the adequacy of the licensee's Class IE equipment evaluation in response to this Bulletin.
In general, the reporting problems encountered in the original responses and the additional information needed can be grouped into the following areas:
1. All Class IE electrical equipment required to function under the postulated accident conditions, both inside and outside primary containment, was not included in the responses.
2. In many cases, the specific information requested by the Bulletin for each component of Class IE equipment was not reported.
3. Different methods and/or formats were used in providing the written evidence of Class IE electrical equipment qualifications. Some licensees used the System Analysis Method which proved to be the most effective approach. This method includes the following information:
a. Identification of the protective plant systems required to function under postulated accident conditions. The postulated accident conditions are defined as those environmental conditions resulting from both LOCA and/or HELB inside primary containment and HELB
outside the primary containment.
IE Bulletin No. 79-QIB
Enclosure 1 Date: January 14, 1980 equipment items within b. Identification of the Class IE electrical a, that are required to each of the systems identified in Item conditions.
function under the postulated accident data requirements specified c. The correlation between the environmental test data for each in the FSAR and the environmental qualificationin Item b above.
identified Class IE electrical equipment item are addressed in IE Bulletin No. 79-01
4. Additional data not previously the environmental qualification of needed to determine the adequacy of data address component aging and Class IE electrical equipment. These operability in a submerged condition.
Operating All Power Reactor Facilities With An Action To Be Taken By Licensees Of Listed on Attachment 1)
License (Except those 11 SEP Plants Engineered Safety Feature Systems (Plant
1. Provide a "master list" of all function under postulated accident conditions.
Protection Systems) required to the LOCA/HELB inside containment, and Accident conditions are defined as system within (including cables, HELB outside containment. For each list identify each Class IE
EPA's terminal blocks, etc.) the master to function under accident electrical equipment item that is required 2 are standard formats to be used conditions. Pages 1 and 2 of Attachmentinformation included.
for the "master list" with typical components of systems listed in Electrical equipment items, which are assumed to operate in the FSAR
Appendix A of Attachment 4, which are mitigate design basis events are safety analysis and are relied on to Bulletin, regardless whether or not considered within the scope of this engineered safety features when the they were classified as part of the The necessity for further up plant was originally licensed to operate. will be dependent on the grading of nonsafety-related plant systems reviews subsequent to TMI/2.
outcome of the licensees and the NRC
item identified in Item 1, provide
2. For each class IE electrical equipment qualification to support the capa- written evidence of its environmental postulated accident conditions. For bility of the item to function under items not having adequate qualifica- those class IE electrical equipment plans for determining qualifications tion data available, identify your completing this action. Provide of these items and your schedule for this in the format of Attachment 3.
For equipment identifed in Items 1 and 2 provide service condition profiles
3. as a function of time). These data (i.e., temperature, pressure, etc., accident conditions and qualification should be provided for design basis provided in profile or tabular form.
tests performed. This data may be
Enclosure 1 IE Bulletin No.79-01B
Date: January 14, 1980 4. Evaluate the qualification of your Class IE electrical equipment against the guidelines provided in Attachment 4. Attachment 5, "Interim Staff Position on Environmental Qualification of Safety-Related Electrical Equipment," provides supplemental information to be used with these guidelines. For the equipment identified as having "Outstanding Items"
by Attachment 3, provide a detailed "Equipment Qualification Plan."
Include in this plan specific actions which will be taken to determine equipment qualification and the schedule for completing the actions.
5. Identify the maximum expected flood level inside the primary containment resulting from postulated accidents. Specify this flood level by elevation such as the 620 foot elevation. Provide this information in the format of Attachment 3.
6. Submit a "Licensee Event Report" (LER) for any Class IE electrical equipment item which has been determined as not being capable of meeting environmental qualification requirements for service intended. Send the LER to the appropriate NRC Regional Office within 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> of identification. If plant operation is to continue following identification, provide justifi- cation for such operation in the LER. Provide a detailed written report within 14 days of identification to the appropriate NRC Regional Office.
Those items which were previously reported to the NRC as not being qualified per IEB-79-01 do not require an LER.
7. Complete the actions specified by this bulletin in accordance with the following schedule:
(a) Submit a written report required by Items 1, 2, and 3 within 45 days from receipt of this Bulletin.
(b) Submit a written report required by Items 4 and 5 within 90 days from receipt of this Bulletin.
This information is requested under the provisions of 10 CFR 50.54(f). Accordingly, you are requested to provide within the time periods specified in Items 7.a and 7.b above, written statements of the above information, signed under oath or affirmation.
Submit the reports to the Director of the appropriate NRC Regional Office.
Send a copy of your report to the U.S. Nuclear Regulatory Commission, Office of Inspection and Enforcement, Division of Reactor Operations Inspection, Washington, D.C. 20555.
Enclosure 1 Date: January 14, 1980 Approval was Approved by GAO, B180225 (R0072); clearance expires 7/31/80. generic problems.
given under a blanket clearance specifically for identified Attachments:
1. List of SEP Plants
2. Master List Standard Format, Typical
3. System Component Evaluation Work Sheet
4. Guidelines for Evaluating Environmental Qualification of Class IE Electrical Equipment in Operating Reactors
5. Interim Staff Position on Environmental Qualification of Safety-Related Equipment (To
Addressees
Only)
Attachment 1 to IE Bulletin 79-O1B
SEP Plants Plant Region Dresden 1 III
Yankee Rowe I
Big Rock Point III
San Onofre 1 V
Haddam Neck I
LaCrosse III
Oyster Creek I
R. E. Ginna I
Dresden 2 III
Millstone 1 I
Palisades III
Facility: XYZ - - -. .E
Dpcket.No.: 50-XXX .MASTER LIST--.- Attachment 'lo. .2-to IE. Bull1etin.79-OIB
-=. - >-: <t>;=m .- :~tgyp~(Typical').Pg1 f_
- --..
--- -~ <C1 ass._IE Electricai Equipment Required to Function
-:--Under.Postulated Accident Conditions). .;
I. SYSTEM: RESIDWUAL-HEAT REMOVAL (RHR)-- ~.:--:.......................;:
COMPONENTS
Location Plant-Identification Inside Primary Outside Primary Number Generic Name Containment Containment IPT 456 -PRESSURE TRANSMITTER x ILT 594 LEVEL TRANSMITTER x
.S 210 LIMIT SWITCH x II. SYSTEM: AUTOMATIC DEPRESSURIZATION SYSTEM (ADS)
COMPONENTS
. . ~Locatilon-.
Plant Identifcation Inside Primary Outside Primary Nuber
. Generic Name Containment Containment B21-ROOI VALVE MOTOR OPERATOR x B21-F003 -SOLENOID VALVE x B21-FOlO PRESSURE SWITCH . x
2 to IE Bulletin 79-01B
SYSTEM. RHR EQUIPMENT/COMOI1NENTS(Typical) Attachment No. l .
II.
- COMPONENTS'.-
k.
I
__________________________________________________________________________
Plant Identification - 4 Number*
O-RING GASKET x
16xP455
- EPA,- Clas~E,
OOC ELECTRICAL PENETRATION ASSEMBLY X
Westinghouse: E
TERMINAL BOARD x KULKA No. ET35 ONKONITE, lOOOV, 3C x x Black POWER CABLE
LUBRICATE OIL x X BRAND 10W-40
15 KB69 (Boston x INSTRUMENTATION CABLE x Wire & Cable)
x Cutler Hamner TB TERMINAL BOX
_ _ _ _
No . - 6_ _ _ _ _ _ _
x x RAYCHEM XYZ CABLE SPLICE
x Scotch No. 54 INSULATING TAPE
TERMINAL LUG x T&B No. 10 INSULATE
SEALANT x x Y Brand Epoxy No;.
.ll ._________________________
identification number, use the
- When a component is not identified by plant etc.
manufacturer, model number, serial number,
- Like components may be referenced.
' Facility: Attachment No. 3 to IE Bulletin No. 79-OIB
SYSTEM COMPONENT EVALUATION WORK SHEET Page I of 3 Unit: (Typical) t'
D ocket:
I'
EfIVI RONMENT DOCU1MENTATION'REF* QALFCTOOTTND IG
EQUIPMENT DESCRIPTION QUALIFICATION OUTSTANDI
pec if- ua li- Specifi- ualiti- METHOD ITEMS
Pa -arameter iDratnn -catin nn . _
System: RHR Operating 15 min. 300 min. 5 Simultaneou! None Plant ID No. IPT456 Time Test Component Temperature SEE ACCIDENT AND 5 Simultaneou!
PRESSURE TRANSMITTER. SEST PROFILESTAN
( ) TEST PROFILES .Test None Manufacture: PROVIDED : ;
Fischer-Porter Co. Pressura o (PSIA) , 1 5 Simultaneou None Model Number: Test
50-EN-1071-BCXN-NS Relative Functlon: Humidity(%) 100% 100% 1 5 Simultaneou None C
Accident Monitoringi. ii __- ' _ Test ,
Chemical N3B03/
Accuracy: Spec: 5% Spray NAOH 1 See Note 1 Demon: 4% NO
Servi ce: RHR Pump lA 4xl066Radiaton rads l.2xlO 8rad 2 6 Sequential Discharge Pressure Test None S/NiO7 1
1. Seq4entf Nn Location: Containment Aging yrs 40 yrs 3 7, 8 Test ysNone Flood Level Elev: 620' Not Not None Above Flood Level: Y Yes lSubmergence Required Required See Note 2 No x 'j_
(
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
-uocumentation References:, Nbtes:
1. 'tSAR Chapter 3, Paragraph 3.11 1. XYZ Letter No. 237-1, dated November 2, 1979,
2. FSAR Chapter 14, Paragraph 14.2.3.1 has been sent to MFG. requesting the qualification
3. Technical Specification 3.4.1, Paragraph A information. If qualification not determined
4. Technical. Speciffcation 4.6.5, Paragraph B acceptable by December 15, 19791, component
5. FIRL Test Report No. ?O00 dated November 2, 1972 will be replaced during refueling outage March 1980.
6. Fischer and Porter Co. Test Report No. 2500-1 .,
. I .
7. A. 0. DOD Engineering Evaluation Data.Report No. 6932 2. In the FSAR submergence was not considered
.8. Wylie Laboratbry Report.Ro. 467 an environmental parameter. ABC Laboratory . I
is to perform submergence test in April 1980.
Attachment 3 to IE Bulletin 79-OIB SYSTEM COMPONENT EVALUATION WORK SHEET
INSTRUCTIONS
1. Equipment Description: Provide the specific information requested for each Class IE electrical component. Provide component location, specific information such as the building, access floor elevations, and whether the component is above the flood level elevation. In addition, provide the specified and demonstrated accuracies of all instruments for their trip functions and/or post accident monitoring requirements. Cables, EPA's, terminal blocks, and other items shall be identified as part of the engineered safety features systems.
2. Environment: List values for each environmental parameter indicated.
List the specification values" obtained from postulated accident analysis in the "SPEC" column. List the "qualification values" obtained from test reports, engineering analysis data, etc. in the "Qual" column. Tempera- ture, pressure, etc., as a function of time shall be provided in profile or tabular form. Specify the time period that the component or equipment is required to function and identify the document which provides the basis for this time interval.
It is expected that some listed parameters were not requested of the licensee at the time of their license issuance: Address each parameter condition during this review. If it is determined that a parameter such as submergence or a service condition such as aging was not previously considered, identify it as an "Outstanding Item."
3. Documentation Reference: Reference the documents from which information was obtained in the "Spec" column. Identify the document, paragraph, etc., that contains the postulated accident environmental specification data. In the "Qual" column identify the document, paragraph, etc., that contains the environmental qualification data.
4. Qualification Method: Identify the method of qualification. To describe the qualification method use words such as simultaneous test, comparison test, sequential test, and/or engineering/mathematical analysis. Words such as "test" and/or "analysis" when used alone do not adequately identify the qualification method.
5. Outstanding Items: Identify parameters for which no qualification data is presently available. Also, identify parameters, service conditions, or environments not previously addressed during FSAR environmental quali- fication analysis such as submergence, qualified life (aging), or HELB.
Identify in the "Notes" section on page 1 of this attachment the actions planned for determining qualification and the schedule for completing these actions.
Attachment 3 of IE Bulletin 79-010 TYPICAL
-2- SERVICE CONDITION PROF
POSTULATED QUALIFICATION EXCEPTIONS
ACCURACY ACCURACY OR
EQUIPMENT ACCIDENT TEST
REQUIREMENTS DEMONSTRATED REMARKS
(
DESCRIPTION ENVIRONMENT ENVIRONMENT
NOTE 3 NOTE 4 NOTE 5 NOTE 6 NOTE 1 NOTE 2 NOTES:
1. Refer to "Equipment Description" on Page 1 of this Enclosure.
to draw a
2. Provide sufficient values of temperature and pressure as a function of time in tabular form characteristic profile.
equipment was qualified
3. Provide sufficient values of temperature and pressure as a function of time for which to draw a characteristic profile. Present this information in tabular form.
post accident monitori(-
4. Provide the accuracy requirements for sensors and transmitters for trip functions and/or as used in the plant safety analysis.
test regarding the trip
5. Provide the accuracy demonstrated by sensors and transmitters during the qualification functions and/or post accident monitoring as applicable.
service condition and
6. Identify any exception or deviation between specified service condition and qualification justification to explain acceptance of deviation.
. Attachment No. 4 to6 3ulTetin 1--01B- GUIDELINES FOR EVALUATING ENVIRONMENTAL QUALIFICATION
OF CLASS IE ELECTRICAL EQUIPMENT
IN OPERATING REACTORS
1.0 Introduction
2.0 Discussion
3.0 Identification of Class IE Equipment
4.0 Service Conditions
4.1 Service Conditions Inside Containment for a Loss of Coolant Accident (LOCA)
1. Temperature and Pressure Steam Conditions
2. Radiation
3. Submergence
4. Chemical SDrays
4.2 Service Conditions for a PWR Main Steam Line Break (MSLB)
Inside Containment
1. Temperature and Pressure Steam Conditions
2. Radiation
3. Submergence
4. Chemical Sprays
4.3 Service Conditions Outside Containment
4.3.1 Areas Subject to a Severe Environment as a Result of aHighEnergy Line Break (HELB)
4.3.2 Areas Where Fluids are Recirculated From Inside C ainment to Accom'lish Lona. "er e Core Coolina Following a LOCA
1. Temoerature, Pressure and Relative Humidity
2. Radiation
3. Submercence
4. Chemical SDrays
. tAttachment No. 4 to IE Bulletin 79-01B
'.Page 2 of 33
-2-
4.3.3 Areas Normally Mat--.talned at Room Conditions
5.0 Qualification Methods
5.1 Selection of Qualification Method
5.2 Qualification by Type Testing
- l. Simulated Service Conditions and Test Duration
2. Test Specimen
3. Test Sequence
4. Test Specimen Aging
5. Functional Testing and Failure Criteria
6. Installation Interfaces
5.3 Qualification by a Combination of Methods (Test, Evaluation, Analysis)
- 6.0 Margin
7.0 Acina
8.0 Documentation Appendix A - Typical Equipment/Functions Needed for Mitigation of a LOCA or MSLB Accident Appendix B - Guidelines for Evaluating Radiation Service Conditions Inside Containment for a LOCA and MSLB Accident Appendix C - Thermal and Radiation Aging Degradation of Selected Materials
Attachment No. 4 to IE Bulletin 79-01B GUIDELINES FOR EVALUATING ENVIRONMENTAL QUALIFICATION
OF CLASS IE ELECTRICAL EQUIPMENT
IN OPERATING REACTORS
1.0 INTRODUCTION
On February 8, 1979, the NRC Office of Inspection and Enforcement issued IE Bulletin 79-01, entitled, "Environmental Qualification of Class IE
Equipment." This bulletin requested that licensees for operating power reactors complete within 120 days their reviews of equipment qualification begun earlier in connection with IE Circular 78-08. The objective of IE Circular 78-08 was to initiate a review by the licensees to determine whether proper documentation existed to verify that all Class IE electrical equipment would function as required in the hostile environment which could result from design basis events.
The licensees' reviews are now essentially complete and the NRC staff has begun to evaluate the results. This document sets forth guidelines for the NRC staff to use in its evaluations of the licensees' responses to IE
Bulletin 79-01 and selected associated qualification documentation. The objective of the evaluations using these guidelines is to identify Class IE
equipment whose documentation does not provide reasonable assurance of environ- mental qualification. All such equipment identified will then be subjected to a plant application-specific evaluation to determine whether it should be requalified or replaced with a component whose qualification has been adequately verified.
These guidelines are intended to be used by the NRC staff to evaluate the qualification methods used for existing equipment in a particular class of plants, i.e., currently operating reactors including SEP plants.
Attachment No. 4 to IE Bulletin 79-01B
2 Equipment in other classes of plants not yet licensed to operate, or replacement equipment for operating reactors, may be subject to different requirements such as those set forth in NUREG-0588, Interim Staff Position on Environmental Qualification of Safety-Related Electrical Equipment.
In addition to its reviews in connection with IE Bulletin 79-01 the staff is engaged in other generic-reviews that include aspects of the equipment qualification issue. TMI-2 lessons learned and the effects of failures of non-Class IE control and indication equipment are examples of these generic reviews. In some cases these guidelines may be applicable, however, this determination will be made as part of that related generic review.
2.0 DISCUSSION
IEEE Std. 323-19741 is the current industry standard for environmental qualification of safety-related electrical equipment. This standard was first issued as a trail use standard, IEEE Std. 323-1971, in 1971 and later after substantial revision, the current version was issued in 1974. Both versions of the standard set forth generic requirements for equipment quali- fication but the 1974 standard includes specific requirements for aging, margins, and maintaining documentation records that were not Included in the 1971 trial use standard.
The intent of this document is not to provide guidelines for implementing either version of IEEE Std. 323 for operating reactors. Infact most of the operating reactors are not committed to comply with any particular industry standard for electrical equipment qualification. However, all of the operating reactors are required to comply with the General Design Criteria
1IEEE Std. 323-1974, 'IEEE Standard for Qualifying Class IEEquipment for Nuclear Power Generating Stations."
.'*. .. -Attachment No. 4 to IE Bulletin 79tO1B
- specified in Appendix A of 10 CFR 50. General Design Criterion 4 states in part that structures, systems and components important to safetS shall be designed to accomodate the affects of and to be compatible with the environmental conditions associated with normal operation, maintenance, testing and postulated accidents, including loss-of-coolant accidents."
The intent of these guidelines is to provide a basis for judgements required to confirm that operating reactors are in compliance with General Design Criterion 4.
3.0 IDENTIFICATION OF CLASS IE EQUIPMENT
Class IE equipment includes all electrical equipment needed to achieve emergency reactor shutdown, containment isolation, reactor core cooling, containment and reactor heat removal, and prevention of significant release of radioactive material to the environment, Typical systems included in pressurized and boiling water reactor designs to perform these functions for the most severe postulated loss of coolant accident (LOCA) and main steanline break accident (MSLB) are listed in Appendix A.
More detailed descriptions of the Class IE equipment installed at specific plants can be obtained from FSARs, Technical specifications, and emergency procedures. Although variation in nomenclature may exist at the various plants, environmental qualification of those systems which perform the functions identified in Appendix A should be evaluated against the appropriate service conditions CSection 4.0).
The guidelines in this document are applicable to all components necessary for operation of the systems listed in Appendix A including but not limited to valves, motors, cables, connectors, relays, switches, transmitters and valve position indicators,
Attachment No. 4 to IE Bulletin 79-O1B -4 -
4.0 SERVICE CONDITIONS
In order to determine the adequacy of the qualification of equipment It Is necessary to specify the environment the equipment is exposed to during normal and accident conditions with a requirement to remain functional, These environments are referred to as the 'service conditions."
The approved service conditions specified in the FSAR or other licensee submittals are acceptable, unless otherwise noted in the guidelines discussued below.
4,1 Service Conditions Inside Containment for a Loss of Coolant Accident (LOCA)
1, Temperature and Pressure Steam Conditions q In general, the containment temperature and pressure conditions as a function of time should be based on the analyses in the FSAR, In the specific case of pressure suppression type containments, the following minimum high tempeature conditions should be used: (l11BWR Drywells . 3400F for 6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br />; and C21 FWR Ice Condenser Lower Compartments - 3400 F for 3 hours3.472222e-5 days <br />8.333333e-4 hours <br />4.960317e-6 weeks <br />1.1415e-6 months <br />.
2.. ?adiation - When specifying radiation service conditions for equipment exposed to radiation during normal operating and accident conditions, the normal operating dose should be added to the dose received during the course of an accident. Guidelines for evaluating beta and gamma radiation service conditions for general areas inside containment are provided below, Radiation service conditions for equipment located directly above the containment sump; in the vicinity of filters, or- submerced in contaminated liquids must be evaluated on a case by case basis, Guidelines for these evaluations are not provided in this document.,
, Attachment No. 4 to IE Bulletin 79-O1B Ganma Radiation Doses - A total gamma dose radiation service condition of 2 x 107 RADS is acceptable for Class IE equipm..at located in general areas inside containment for PWRs with dry type containments, Where a dose less than this value has been specified, an application specific evaluation must be performed to determine If the dose specified is acceptable. Procedures for evaluating radiation service conditions in such cases are provided In Appendix B, The procedures in Appendix B are based on the calculation for a typical PWR reported in Appendix D of XUREG-.0588 1 Ga6nna dose radiation service conditions for BWRs and PWRs with ice condenser containments must be evaluated on a case by case basis.
Since the procedures in Appendix B are based on a calculation for a typical PWR with a dry type containment, they are not directly applicable to BWRs and other containment types, However, doses for these other plant configurations may be evaluated using similar procedures with conservative dose assumptions and adjustment factors developed on a case by case basIs, Bet.a Radiation Doses - Beta radiation doses generally are less significant than gama radiation doses for equipment qualification, This is due to the low penetrating power of beta particles in comparison to gamma rays of equivalent energy, Of the general classes of electrical equipment in a plant (etg,, cables, instrument transmitters, valve operators, containment penetrations), electrical cable is considered the most
1NUkE-0588, Interim Staff Position on Environmental Qualification of SafetyRelated Electrical Equipment.
Attachment No. 4 to IE Bulletin 79-OIB - 6- vulnerable to damage from beta radiation. Assuming a TID 14844 source term, the average maximum beta energy and isotopic abundance will vary as a function of time following an accident. If these parameters are considered in a detailed calculation, the conservative beta surface dose of 1.40 x x 108 RADS reported in Appendix 0 of NUREG
0588 would be reduced by approximately a factor of ten within 30 mils of the sur face of electrical cable insulation of unit density. An additional 40 mils of insulation (total of 70 mils) results in another actor of 10 reduction in dose. Any structures or other equipment in the vicinity of the equipment of interest would act as shielding to further reduce beta doses. If it can be shown, by assuming a conserva- tive unshielded surface beta dose of 2.0 x 108 RADS and considering the shielding factors discussed here, that the beta dose to radiation sensitive equipment internals would be less than or equal to 106 of the tota' garma dose to which an item of equipment has been qualified, then that equipment may be considered qualified for the total radiation environment (gamma plus beta). If this criterion is not satisfied the radiation service condition should be determined by the sum of the garma and beta doses.
3. Submercence - The preferred method of protection against the effects of submEergency is to locate equipment above the water flooding level.
Specifying saturated steam as a service condition during type testing of equipment that will become flooded in service is not an acceptable alternative for actually flooding the equipment during the test.
-7 Attachment No. 4 to IE Bulletin 79-O0B 4. Containment Sprays - Equipment exposed to chemical sprays should be qualified for the most severe chemical environment (actdic or basic) which could exist, Demineralized water sprays should not be exempt from consideration as a potentially adverse service condition.,
4.2 Service Conditions for a PWR Main Steam Line Break (MSLB) Inside Containment Equipment required to function in a steam line break environment must be qualified for the high temperature and pressure that could result.
In some cases the environmental stress on exposed equipment may be higher than that resulting from a LOCA, in others it may be no more severe than for a LOCA due to the automatic operation of a containment spray system.
1. Ter.Derature and Pressure Steam Conditions - Equipment qualified for a LOCA environment is considered qualified for a MSLB accident environ- rer.t in plants with automatic spray systems not subject to disabling single component failures. This position is based on the 'Best Estim.at'e calculation of a typical plant peak temperature and pressure and a therma' analysis of typical components inside containment.1 /
The 'inal acceptability of this approach, i.e., use of the 'Best Estimate",
is pending the completion of Task Action Plan A-21, Main Steamline Break Inside Containment.
Class IE equipment installed in plants without automatic spray systems or plants with Spray systems subject to disabling single failures or delayed initiation should be qualified for a MSLB accident environment determined by a plant specific analysis. Acceptable methods See NURE 0456, Short Term Safety Assessment on the Environmpntal Qualification of Safety-Related Electrical Equipment of SEP Operating Reactors, for a more detailed discussion of the best estimate calculation.
Attachment No. 4 to IE Bulletin 79-O1B for performing such an analysis for operating reactors are provided in Section 1.2 for Category II plants in NUREG-0588, Interim Staff Position on Environmental Qualification of Safety-Related Eletctrical Equipment.
2. Radiation - Same as Section 4.1 above except that a conservative gamia dose of 2 x 106 RADS is acceptable.
3. Submercence - Same as Section 4.1 above.
4. Chemical Sprays - Same as Section 4.1 above.
4.3 Seruice Conditions Outside of Containment
4.3.1 Areas Subject to a Severe Environment as a Result of a High Energy Line Break 'HELB)
Service conditions for areas outside containment exposed to a HELB were evaluated on a plant by plant basis as part of a program initiated by the staff in Dece.mber, 1972 to evaluate the effects of a HELB. The equipment required to mitigate the event was also Identified. This equipment should be qualified for the service conditions reviewed and approved n tne i.-. Sa-ezy Evaluation Report. for each specific plant.
4.3.2 Areas Where Fluids are Recirculated from Inside Containment to Accomplish Lona-Temn Core Coolino Followina a LOCA
1. Termerature and Relative Humidity - One hundred oercent relative humidity shouTd be established as a service condition in confined spaces. The temoerature and pressure as a function of time should be based on the plant unique analysis reported in the FSAR.
Attachment No. 4 to IE Bulletin 79-O1B 2. Radiation - Due to differences in equipment arrangement within these areas and the significant effect of this factor on doses, radiation service conditions must be evaluated on a case by case basis. In general, a dose of at least 4 x 106 RADS would be expected.
3. Submergence - Not applicable.
4. Chemical Sorays - Not applicable.
4.3.3 Areas Normally Maintained at Room Conditions Class IE equipment located in these areas does not experience significant stress due to a change inservice conditions during a design basis event.
This equipment was designed and installed using standard engineering practices and industry codes and standards (e.g., ANSI, NEMA, National
- Electric Code). Based on these factors, failures of equipment in these areas during a design basis event are expected to be random except to the extent that they may be due to aging or failures of air conditioning or ventilation systems. Therefore, no special consideration need be given to the environmental qualification of Class IEequipment in these areas provided the aging requirements discussed in Section 7.0 below are satisfied and the areas are maintained at room conditions by redundant air conditioning or ventilation systemis served by the onsite emergency electrical power system.
Equip.ent located irf areas not served by redundant systems powered from onsite emergency sources should be qualified for the environmental extremes which could result from a failure of the systems as determined from a plant specific analysis.
5.0 QJALIFICATION METHODS
Attachment No. 4 to IE Bulletin 79-OB lo: V
- 10 -
5.1 Selection of Qualification Method The choice of qualification method employed for a particular application of equipment is largely a matter of technical Judgement based on such factors as: (1) the severity of the service conditions; (2)the structural and material complexity of the equipment; and (3) the degree of certainty required in the qualification procedure (i.e., the safety importance of the equipment function). Based on these considerations, type testing is the preferred method of qualification for electrical equipment located inside containment required to mitigate the consequences of design basis events, i.e., Class IE equipment (see Section 3.0 above). As a minimum, the cualification for severe temperature, pressure, and steam service conditions for Class IE equipment should be based on type testing.
- Qualification for other service conditions such as radiation and chemical sprays may be by analysis (evaluation) supported by test data (see Section
5.3 below). Exceptions to these general guidelines must be justified on a case by case basis.
5.2 Oualification by Tyce Testina The evaluation of test plans and results should include consideration of the following factors:
1. Simulated Service Conditions and Test Duration - The environment in the test chamber should be established and maintained so that it envelopes the service conditions defined in accordance with Section 4.0 above.
The time duration of the test should be at least as long as the period from the initiation of the accident until the temperature and pressure service conditions return to essentially the same levels that existed before the postulated accident. A shorter test duration may be acceptable
Attachment No. 4 to IE Bulletin 79-01B
-1 if specific analyses are provided to demonstrate that the materials involved t 11 not experience significant accelerated thermal aging during the period not tested.
2. Test Soecimen - The test specimen should be the same model as the equipment being qualified. The type test should only be considered valid for equipment identical in design and material construction to the test specimen. Any deviations should be evaluated as part of the qualifica- tion documentation (see also Section 8.0 below).
3. Test Secuence - The component being tested should be exposed to a steam./air environment at elevated temperature, and pressure in the sequence defined for its service conditions. Where radiation is a service condition which is to be considered as part of a type test, it may-be applied at any time during the test sequence provided the component does not contain any materials which are known to be susceptible to significant radiation damage at the service condition levels or materials whose susceptibility to radiation damage is not known (see Apn-endix C). If the component contains any such materials, the radiation dose should be applied prior to or concurrent with exposure to the elevated temperature and pressure steam/air environment. The same test specimen should be used throughout the test sequence for all service conditions the equipment is to be qualified for by type testing. The type test should only be considered valid for the service conditions applied to the sare test specimen in the appropriate sequence.
4. Test Soecimen Acing - Tests which were successful using test specimens which had not been preaged may be considered acceptable provided the co0cnent does not contain materials which are known to be susceptible
Attachment No. 4 to IE Bulletin 79-01B v
- 12 -
to significant degradation due to thermal and radiation agir. (see Section
7.0). If the component contains such materials a qualified life for the component must be established on a case by case basis. Arrhenius techniques are generally considered acceptable for thermal aging.
S. Functional Testing and Failure Criteria - Operational modes tested should be representative of the actual application requirements (e.g., components which operate normally energized in the plant should be normally energized during the tests, motor and electrical cable loading during the test should be representative of actual operating conditions). Failure criteria should include instrument accuracy requirements based on the maximum error assumed in the plant safety analyses. If a component fails at any time during the test, even in a so called "fail safe" mode, the test should be considered inconclusive with regard to demonstrating the ability of the component to function for the entire period prior to the failure.
6. Installation Interfaces - The equipment mounting and electrical or mechanical seals used during the type test should be representative of the actual installation for the test to be considered conclusive.
The equipment qualification program should include an as-built inspection in the field to verify that equipment was installed as it was tested. Particular emphasis should be placed on common problems such as protective enclosures installed upside down with drain holes at the top and penetrations in equipment housings for electrical connections being left unsealed or susceptible to moisture incursion through stranded conductors.
Attachment No. 4 to IE Bulletin 79-O1B
- : -13 5.3 Oualification by a:Combination of Methods (Test, Evaluation, Analysis As discussed in Section 5.1 above, an item of Class IE equipment may be shown to be qualified for a complete spectrum of service conditions even though it was only type tested for high temperature, pressure and steam. The qualification for service conditions such as radiation and chemical sprays may be demonstrated by analysis (evaluation). In such cases the overall qualification is said to be by a combination of methods. Following are two specific examples of procedures that are considered acceptable. Other similar procedures may also be reviewed and fown: acceptable on a case by case basis.
1. Radiation Oualiflcation - Some of the earlier tvop tests performed for operating reactors did not include radiation as a service condition. In these cases the equipment may be shown to be radiation qualified by performing a calculation of the dose expected, taking into account the time the equipment is required to remain functional and its location using the methods described in Appendix B, and analyzing the effect of the calculated dose on the materials used in the equipment (see Appendix C). As a general rule, the time required to remain functional assumed for dose calculations should be at least 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br />.
2. Chemical SDray Qualification - Components enclosed entirely in corrosion resistant cases (egg.1 stainless steel) may be shown to be qualified for a chemical environment by an analysis of the effects of the particular chemicals on the zarticular enclo- sure materials. The effects of chemical sprays on the pressure inmtegrity of any gaskets or seals present should be considered in the analysis.
. Attachment No. 4 to IE Bulletin 79-O1B
_14 6.0 Marcin IEEE Std. 323-1974 dC ines margin as the difference between the most severe specified service conditions of the plant and the conditions used in type testing to account for normal variations in commercial production of equipment and reasonable errors in defining satisfactory performance.
Section 6.3.1.5 of the standard provides suggested-factors to be applied to the service conditions to assure adequate margins. The factor applied to the time equipment is required to remain functional is the most significant in terms of the additional confidence in qualification that is achieved by adding margins to service conditions when establishing tes: environments. For this reason, special consideration was given to the time required to remain functional when the guidelines for Functional Testing and Failure Criteria in Section 5.2 above were established. In addition, all of the guidelines in Section 4.0 for establishing service conditions include conservatisms which assure margins between the service conditions specified and the actual conditions which could realistically be expected in a design basis event. Therefore, if the guidelines in Section 4.0 and 5.2 are satisfiedino separate margin factors are required to be added to the service conditions when specifying test conditions.
7.0 Acina Inpiicit in the-staff position in Regulatory Guide 1.89 with regard to backfitting IEEE Std. 323-1974 is the staff's conclusion that the incremental improvement in safety from arbitrarily requiring that a specific qualified life be demonstrated for all Class IE equipment is not sufficient to justify the expense for plants already constructed and operating. This position does not, however, exclude equipment
.* Attachment No. 4 to IE Bulletin 79-O1B using materials that have been identified as being susceptible to significant degradation due to thermal and radiation aging. Component maintenance or replacement schedules should include considerations of the specific aging characteristics of the component materials. Ongoing programs should exist at the plant to review surveillance and maintenance records to assure that equipment which is exhibiting age related degrada- tion will be identified and replaced as necessary. Appendix C contains a listing of materials which may be found in nuclear power plants along with an indication of the material susceptability to thermal and radiation aging.
8.0 Documentation Cornplete and auditable records must be available for qualification by any of the methods described in Section 5.0 above to be considered valid.
These records should describe the qualification method in sufficient detail to verify that all of the guidelines have been satisfied. A simple vendor certification of compliance with a design specification should not be considered adequate.
Attachment No. 4 to IE Bulletin 79-OlB APPENDIX A
TYPICAL EQUIPMENT/FUNCTIONS NEEDED FOR
MITIGATION OF A LOCA OR MSLB ACCIDENT
Engineered Safeguards Actuation Reactor Protection Containment Isolation Steanrline Isolation Main Feedwater Shutdown and Isolation Emergency Power Emergency Core Cooling1 Contairment Heat Renoval Containment Fission Product Removal Containment Conbustible Gas Control Auxiliary Feedwater Containment Ventilation Containment Radiation Monitoring Control Room Habitability Systems (e.g., HVAC, Radiation Filters)
Ventilation for Areas Containing Safety Equipment Component Cooling Service Water Emergency Shutdown 2 Post Accident Sampling and Monitoring Radiation Monitoring3 Safety Related Display Instrumentation3
Attachment No. 4 to IE Bulletin 79-O1B These systems will differ for PWRs and BWRs, and for older and newer plents. In each case the system features which allow fov transfer to recirculation cooling mode and establishment of long term cooling with boron prec-ipitation control are to be considered as part of the system to be evaluated.
Emergency shutdown systems include those systems used to bring the plant to a cold shutdown condition following accidents which do not result in a breach of the reactor coolant pressure boundary together with a rapid depressurization of the reactor coolant system. Examples of such systems and equipment are the RHR system, PORVs, RCIC, pressurizer sprays, chemical and volumse control system, and steam dump systems.
3 More specific identification of these types of equipment can be found in the plant emergency procedures.
.* Attachment No. 4 to IE Bulletin 79-O1B
-~~~~ PEN~ El v PROCEU?.ES FOR EVALUATING G6MfA RADIATION SERVICE CONDITWNS
Introduction and Discussion The adequacy of gamnma radiation servi-ce conditions specified for inside containment during a LOCA or FML3 accident can be verified by assuming a conservative dose at the contaTlment centerline and adjusting the dose according the plant specific parameters; The purpose of this appendix ts to identify thase paraneters whose effect on the total gamma dose is easy to quantify with a high degree of ccnfidence and describe procedures which may be used to take these effects into consideration.
The bases for the procedures and restrictions for their use are as follows:
(l} A conservative dose at the containment centerline of 2 x 107 RADS
for a LOCA and 2 x 10i RADS for a MSLE accident has been assumed.
This assumption and all the dose rates used in the procedure out- lined below are based on the methods and sample calculation described In Appendix D of WP.EG-053, "Interim Staff Position on Environrental Qualification of Safety-Related Electrical Equip- ment. " Therefore, all the llmitations listed in Appendix D of NURES-.588 apply to these procedures.
t2) The sample calculation In Appendix D of HLUREG-0588 is for a 4,000
MWth pressurized water reactor housed in a 2.52 x 1O6 ft 3 contain- ment wi.th an Iodine scrzbbing spray system. A similar calculation without Iodine scrubbint sprzys would increase the dose to equipment approxriately 150. The conservative dose o.' 2 x 107 RADS assumed
S. . ,'Attachment No. 4 to IE Bulletin 79-O1B
-2- in the procedure below includes sufficient conservatism to account for this factor. Therefore, the proc.edure is also applicable to plants without an iodine scrubbing spray system.
(3) Shielding calculations are based on an average gamma energy of
1 MEY derived from TID 14844.
(4) These procedures are not applicable to equipment located directly above the containment sump, submerged in contaminated liquids, or near filters. Doses specified for equipment located in these areas must be evaluated on a case by case basis.
(5) Since the dose adjustment factors used in these procedures are based on a calculation for a typical pressurized water reactor with a dry type containment, they are not directly applicable to boiling water reactors or other containment types. However, doses for these other plant configurations may be evaluated using similar procedures with conservative dose assumptions and adjustment factors developed on a case by case basis.
Procedure Figures I through 4 provide factors to be applied to the conservative dose to correct the dose for the following plant specific parameters:
(1) reactor power level; (2) containment volume; (3)shielding; (4)
compartment volume; and (5)time equipment is required to remain functional.
- ,. .- Attachment No. 4 to IE Bulletin 79-O1B
'~.-. * ,Page 22 of 33
-3- The procedure for using the figures is best illustrated by an example.
Consider the following case. The radiation service condition for a particular item of equipment has been specified as 2 x 106 RADS. The application specific parameters are:
Reactor power level - 3,000 MWth Containment volume - 2.5 x 106 ft3 Compartment Volume - 8,000 ft3 Thickness of compartment shield wall (concrete) - 24"
Time equipment is required to remain functional - 1 hr.
The problem is to make a reasonable estimate of the dose that the equipment could be expected to receive in order to evaluate the adequacy of the radiation service condition specification.
Step 1 Enter the nomogram in Figure 1 at 3,000 MWth reactor power level and
2.5 x 10i ft3 containment volume and read a 30-day integrated dose of
1.5 x 107 RADS.
SteD 2 Enter Figure 2 at a dose of 1.5 x 107 RADS and 24" of concrete shielding for the compartment the equipment is located in and read 4.5 x 104 RADS.
This is the dose the equipment receives from sources outside the compart- ment. To this must be added the dose from sources inside the compartment
.(Step 3).
Stem 3 Enter Figure 3 at 8,000 ft3 and read a correction factor of 0.13. The dose due to sources inside the compartment would then be 0.13 (1.5 x 107)
1.95 x 106 RADS. The sums of the doses from steps 2 and 3 equals:
4.5 x 104 RADS + 0.13 (1.5 x 107)- RADS - 2.0 x 106 RADS
Attachment No. 4 to IE Bulletin 79-OlB
Page-23 of 33
-4- Step 4 Enter Figure 4 at 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> and read a correction factor of 0.15. Apply this factor to the sum of the doses determined from steps 2 and 3 to correct the 30 day total dose to the equipment inside the compartment to 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br />.
0.15 (Z.O xl10 6 1 = 3 x 105 RADS
In this particular example the service condition of 2 x 106 RADS
specified is conservative with respect to the estimated dose of 3 x
105 RADS calculated in steps 1 through 4 and is, therefore, acceptable.
J
FIGURE 1
. K1tGAM FOR rONTAINMENT VOLUME AND REACTOR P'- m
- &n JA DOSE CORRECTIONS*
Attachment No. 4 to IE Bulletin 79-OlB
CONTAINMEN T II VOLUME (ft3)
3xlC _
2x1C
~6
30 DAY
MWTH INTEGRATED
I Xi1o 40 YDOSE
4o00_
40DW _ 4 x 10o
3000k_
3 x 107 K
5 x 105- -
1000
4x10V
500% 2 x107
. 3x16
2x 10 w
200 E 1 x 107
-
I x 1O
5x 1061 _
4 x 106 _
3x106
2.S x 106
2.0 x 106 I-
1 x 106
_I
- ISLB ACCIDENT DOSES SHOULD BE READ AS A FACTOR OF 10 LESS
DOSE CORRECTION FACTOR FOR CONCRETE SHIELDING
Y(ONLY) Attachment NcoA to IE Bul letin 79-01B
108 page 25 of 33 x1 S x oS
0
1 X104
- I-
l10:3 ', fitIds , Nit~to t I
- 1oC 1O7 106 10 S
I DOSE (RADS) WITHOUT SHIELDING (FROM FIGURE 1)
a FIGURE 3 \
DOSE CORRECTIN FACTOR FOR COMPARTMENT VOLUMBE
Attachment No. 4 to IE Bulletin 79-O1B 106
-
I
I-
- 0
Lu
106 z
0
C
C;
CD
I I I I I I I ,I I I
0 .2 .4 .6 .8 1.0
CORRECTION FACTOR
D URE 4 DOSE CORRECTION FOR TIME hEQUIRED TO REMAIN FUNCTIONAL
c- V-.
- 1 C.a,
-
w U.-
r-..o U 1.0 -
4J
4Ju I
Ad O
=: VI)
0
C.0 .
0n.
al
.1 .
II , .. a I i II fi II I A I I fia ll I I I I I i lt I I I I l I I I II hIIII
.01 , I ........... . ..
.1 1.0 10 100 1000
TIME REQUIRED TO REMAIN FUNCTIONAL MHRSP
4
- - .
Attachment No. 4 to IE Bulletin 79-O0B
t ' *Pale 28 of 33
- APPENDI C
ThERMAL AND RADIATION AGING DEGRADATION
OF SELECTED MATERIALS
Table C-1 is a partial list of materials which may be found in a nuclear power plant along with an indication of the material susceptibility to radiation and thermal aging.
Susceptibility to significant thermal aging in a 450 C environment and normal atmosphere for 10 or 40 years is indicated by an (*) in the appro- priate column. Significant aging degradation is defined as that amount of degradation that would place in substantial doubt the ability of typical equipment using these materials to function in a hostile environment.
- Susceptibility to radiation damage is indicated by the dose level and the observed effect identified in the column headed BASIS. The meaning of the terms used to characterize the dose effect is as follows:
- Threshold - Refers to damage threshold, which is the radiation exposure required to change at least one physical property of the material.
- Percent Change of Property - Refers to the radiation exposure required to change the physical property noted by the percent.
I Allowable - Refers to the radiation which can be absorbed before serious degradation occurs.
The information in this appendix is based on a literature search of sources including the National Technical Information Service (NMIS), the National Aeronautics and Space Administration's Scientific and Technical Aerospace Report (STA.), NTIS Government Report Announcements and Index (GRA), and
.Attachment
- No. 4 to IE Bulletin 79-O1B 2- various manufacturers data reports. The materials list is not to be considered all inclusive neither is it to be used as a basis for specifying materials to be used for specific applications within a nuclear plant. The list is solely intended for use by the NRC staff in making Judgements as to the possibility of a particular material in a particular application being susceptible to significant degradation due to radiation or thermal aging.
The data base for thermal and radiation aging in engineering materials is rapidly expanding at this time. As additional information becomes available Table C-1 will be updated accordingly.
11/14/79 TABLE C-1 THERMAL AND RADIATION AGING DEGRADATION
OF SELECTED MATERIALS
r1 T I
TyPrs or rQtUiPI*N.tr (wrI~nll WHIh
10 iTEIAi, NAly lip tyoII))
RtADIATION
smirnICANT
SUSCEPTIDI LITY IA
ALSO AGING
flAs
% y I C'
"'h MATlt:I At. AS 10 YILS 140 YRS t'HK IIAS I S
I- - 1~ -Afi ! I I I _-I _ I
Integrated Circuits JIC) Threshold Integrated Circuits IIC) K
C-tiS
104 K
Transltors
104 Diodes I
a Silicon-Controlled 14 l K
Rectifiers Integrated Circuits (IC)
Analog Ix xC
Vulcanized Fiber K K K DP 0
Fish Paper 105 K I K K x M SU
Polyester (unfilled) 105 K x K K I x x Nylon Polyamide 105 K I x K x x I K x 0
ik A 106 x K x C*
l Polycarbondte Polywide 6 x I K 0
Chlorosulfonated Poly- Itypalon 10. Allowable K K I C
O
ethylene
8um-n 'tSR/ti- 106 Threshold I K I
trile W=
tubber Integrated Circuit. (IC) 106 I
biallyl Phthalate )AP
a Silicone Rubbet K K
X
. I __________ I I L
- Indicates that there is data available which shows a potential for significant thermal aging of the materials when exposed to normal operating conditions for either 10 or 40 years as indicated.
11/14/79
11/14/79 I.
9-v U r TYPES OF EQUIPAUrTr (WITHIN wiiiaC MATERIAL M"Y UK INwXI .
ALSO
rOTENTIAL
OR.
tlCNIFICIWT
AGING
RRMArloN
SuscePTInILITY
/77 -4kv1
- MTreAL AS i0 YM 40 YM8 I Is a I I- I I I
1107 fllowable I
Polysultone wrasde 10l 24% Loss X X X I S
of Elonga- tion
19 rhrerhold I X I N
Reaistora - Wire-ound I
109 a K X I U I
Resistors - Carbmr omposition Capacitors - Ceramia 109 Allowable K I
K
I tC
U I K I N
Capacitors - alas. 109 Capacitora - Rica 109 K I 3.X K -0:r-
109 I IDOt ENA Thermosetting 0
Lamnatee, Oar X c HEA Thermos.ttin' 109 X
Laminates, Grafe XXXP
"EOA theuosetting l0g
109 I CD
Laminate.. Grafe XPX
Nm Thermosetting U I @_hC
Laminates, Grade XPC
109 a 0
WMR Thermoeetting X I K
Laminates, Grata XX
HEt Thermoaetting 109 I I
f "I
LaOinate.. Grade XXP N.
s-I
mHE¶termosattinq 109 aa I I K
Laminate., CGra XXX K ID
40
MhETherrmoetting 109 CI
I 1-4 Laminate, Graft Ce U
eOM Thermoaetting 109 s- La"nate. GCrade C
O,
.1 L 1. .1
I ;i11/14/79
- vI;_
iTypes or rvQuirfl ("ITIN WIlc0 IIRTERIAI4 .MAT IIe
1 09flU))
ron
5IE."IFICAPM SS~T1ILT
109 Shre0l AS 10 vp' 40 Tits GM BSI
1L09 Threehold t9
103 1
1099
109 N
9
10
109 *
1010 1
It
1 W
ENCLOSURE 2 IE Bulletin No. 79-O0B
Date: January 14, 1980 RECENTLY ISSUED IE BULLETINS
Bulletin Subject Date Issued Issued To No.
79-13 Cracking in Feedwater 10/17/79 All PWRs with an OL
(Rev. 2) System Piping and Designated Ap- plicants (for Action),
All Other Power Reactor Facilities with an Operating License (OL) or Con- struction Permit (CP)
(for Information)
79-17 Pipe Cracks in Stagnant 10/29/79 All PWRs with an (Rev. 1) Borated Water Systems OL (for Action). All other Power Reactor Facilities with an OL or CP (for In- formation)
79-25 Failures of Westinghouse 11/2/79 All Power Reactor BFD Relays in Safety- Facilities with an Related Systems OL or CP (for Action)
79-02 Pipe Base Plate Designs 11/8/79 All Power Reactor (Rev. 2) Using Concrete Expansion Facilities with an Bolts OL or CP
79-26 Boron Loss From BWR 11/20/79 All BWR Power Reactor Control Blades Facilities with an OL
79-27 Loss of Non-Class-1-E 11/30/79 All Power Reactor Instrumentation and Con- Facilities with an OL
trol Power System Bus and those nearing During Operation Licensing (for Action)
All Power Reactor Facilities with a CP
(for Information).
79-28 Possible Malfunction 12/7/79 All Power Reactor of NAMCO Model EA180 Facilities with an Limit Switches at OL or CP
Elevated Temperatures