ML19247A076
| ML19247A076 | |
| Person / Time | |
|---|---|
| Site: | Sterling |
| Issue date: | 07/11/1979 |
| From: | Grier B NRC OFFICE OF INSPECTION & ENFORCEMENT (IE REGION I) |
| To: | Arthur J ROCHESTER GAS & ELECTRIC CORP. |
| References | |
| NUDOCS 7907270368 | |
| Download: ML19247A076 (1) | |
Text
pa arc,
o ef ' '
h UNITED STATES d
8 ',
.c, c ( h NUCLEAR REGULATORY COMMISSION Gj
-/
C REGION I r
S@
[
631 PARK AVENUE
%, ' \\/ g[
KING OF PRUSSIA, PENNSYLVANix 19406 July 11, 1979 Docket No. 50-485 Rochester Gas & Electric Corporation ATTN:
Mr. J. E. Arthur Chief Engineer 89 East Avenue Rochester, New York 14649 Gentlemen:
The enclosed Bulletin No. 79-15 is forwarded to you for action.
A written response is equired.
If you desire additional information regarding this matter, please contact this ffice.
Sincerely, Y
/
~
oyce H. Grier
' Director
Enclosures:
1.
IE Bulletin No. 79-15 w/ Attachments 2.
Listing of IE Bulletins Issued in Las+ Twelve Months c w/encls:
C. R. Anderson, Manager, QA Lax K. Larson, Esquire N. A. Petrio., Executive Director, SNUPPS Gerald Charnoff, Esquire E750Lb 7 9Q7270 f,g t'
j
ENCLOSURE 1 UNITED STATES NUCLEAR REGULATORY COMMISSION OFFICE OF INSPECTION AND ENFORCEMENT WASHINGTON, D.C.
20555 IE Bulletin No. 79-15 Date:
July 11, 1979 Page 1 of 3 DEEP DRAFT PUMP DEFICIENCIES Description of Circumstances:
On October 20, 1978, Commonwealth Edison Company reported that manufacturing deficiencies had been identified in new high pressure core spray, low pressure core spray, and residual heat removal pumps manufactured by Inga:soll-Rand (I-R)
Company, Cameron Pump Division.
Each of these pumps is a vertical turbine pump with impellers located in bowls in a sump or a self contained barrel.
The motor (prime mover) is located at the highest pump elevation to take into account maximum flooding at the site or space considerations.
The suction is at the lower end of the pump while the discharge head is just below the driver.
Bearings supporting the vertical shaft segments (usually 5 to 10 segments) are either self lubricated, force fed (lubricated by fluid being pumped), or oil lubricated and maintained within their own isolated system.
These pumps are designated as " Deep Draft".
Figures 1&2 show typical outlines of such pumps.
The internal deficiencies, identified through dimensional and visual inspections were as follows:
Low Pressure Core Spray Pumps (I-R Model No. 29APKD-5) (Date of Manufacture -
Feburary 1973)
Loose impeller bolts and bolts improperly staked Loose key - keyway fit Excessive runout on pump shaft Bearing showed wear Bearing clearance exceeded recommended tolerance Coupling thread galled Wear ring clearance out-of specification b /5CM Impeller-to-shaft clearance out of specification Cracks found in second-and-third-stage impellers Stuffing box bushings were severely galled High Pressure Core Spray Pumps (I-R Mode' % 'q^*;'""*~-C "-"Tc"^
y September 1972)
DUPLICATE DOCUMENT Bearing clearance exceeded recommendet Wear ring clearance out-of-specificat.
Entire document previously entered Bearings showed wear into system under:
7907/f O/25
.c ANO I.
s f:
No. of pages:
h 90 m.-
m