ML17263A612
| ML17263A612 | |
| Person / Time | |
|---|---|
| Site: | Ginna  |
| Issue date: | 03/30/1994 |
| From: | ROCHESTER GAS & ELECTRIC CORP. |
| To: | |
| Shared Package | |
| ML17263A585 | List:
|
| References | |
| ECA-3.2, NUDOCS 9404190162 | |
| Download: ML17263A612 (62) | |
Text
EOP:'CA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 1 of 25 ROCHESTER GAS AND ELECTRIC CORPORATI GINNA STATION CONTROLLED COPY NUMBER TECHNICAL REVIE PORC REVIE DATE '6 I PLANT S PE NTENDENT 4-') -9 EFFECTIVE DATE CATEGORY 1.0 REVIEWED BY:
r J 940419'0162 9404i4
'PDR ADOCK 05000244 J,"
- .'P PDR
)
t
4 I
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 2 of 25 A.
PURPOSE This procedure provides actions to cool down and depressurize the RCS to cold shutdown conditions while minimizing loss of RCS inventory and voiding in the RCS.
B.
ENTRY CONDITIONS/SYMPTOMS 1.
ENTRY CONDITIONS This procedure is entered from:
a.
ECA-3.1, SGTR WITH LOSS OF REACTOR COOLANT-SUBCOOLED RECOVERY DESIRED, when RWST level is low without a corresponding increase in containment sump level.
b ~
ECA 3
1 I SGTR WITH LOSS OF REACTOR COOLANT SUBCOOLED RECOVERY DESIRED, when the ruptured S/G level is high and plant staff selects saturated recovery method.
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 3 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED
- %'*****%x* x m ***x*********************
CAUTION IF RWST LEVEL DECREASES TO LESS THAN 28%,
THEN THE SI SYSTEM SHOULD BE ALIGNED FOR COLD LEG RECIRCULATION USING ES-1.3, TRANSFER TO COLD LEG RECIRCULATION.
x**x x x **% *x x x **x% x
- x x**x %'***************
NOTE:
o Steps 1 through 1S of ECA-3.1, SGTR WITH LOSS OF REACTOR COOLANT SUBCOOLED RECOVERY DESIRED, should be performed before continuing with this procedure.
o FOLDOUT page should be open and monitored periodically.
o Adverse CNMT values should be used whenever CNMT pressure is greater than 4 psig or CNMT radiation is greater than 10+
R/hr.
1 Add Makeup To RWST As Necessary:
o Refer to S-9J, BLENDING TO RWST
-OR-o Refer to S-3. 2D, TRANSFERRING WATER FROM CVCS HUT(S)
-OR-o Refer to Attachment SFP-RWST
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 4 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED x*x*x**xx x x x*xx**xx***xx*x***x**x x x******
CAUTION o
IF OFFSITE POWER IS LOST AFTER SI RESET, THEN SELECTED SW PUMPS AND ONE CCW PUMP WILL AUTO START ON EMERGENCY D/G.
MANUAL ACTION WILL BE REQUIRED TO RESTART SAFEGUARDS EQUIPMENT.
o RCS PRESSURE SHOULD BE MONITORED.
IF RCS PRESSURE DECREASES TO LESS THAN 250 PSIG
[465 PSIG ADVERSE CNMT), THEN THE RHR PUMPS MUST BE MANUALLY RESTARTED TO SUPPLY WATER TO THE RCS.
x **x **x x x x
- x x **x x x **x******************
2 Check If RHR Pumps Should Be Stopped:
a.
Check RCS pressure:
/
- 1) Pressure GREATER THAN 250 psig (465 psig adverse CNMT]
2)
RCS pressure STABLE OR INCREASING a.
Go to Step 3.
b.
Stop RHR pumps and place in AUTO
g'C J
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV'3 PAGE 5 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED x x
- x' ***x **x ***x *******x**********
CAUTION IF ANY RUPTURED S/G IS
- FAULTED, FEED FLOW TO THAT S/G SHOULD REMAIN ISOLATED DURING SUBSEQUENT RECOVERY ACTIONS UNLESS NEEDED FOR RCS COOLDOWN.
x * ***x ****x ********************
- 3 Monitor Ruptured S/G Level:
a.
Narrow range level GREATER THAN 5%
(25% adverse CNMT]
- a. IF ruptured S/G NOT faulted, THEN perform the following:
l) Maintain feed flow to ruptured S/G until level greater than 5%
[25% adverse CNMT].
- 2) Continue with Step 4.
WHEN ruptured S/G level greater than 5%
(25% adverse CNMT],
THEN do Steps 3b through e.
- b. Close MDAFW pump discharge valve to ruptured S/G
- b. Dispatch AO to locally close valve.
~ S/G A, MOV-4007
~ S/G B, MOV-4008
- c. Pull stop MDAFW pump for ruptured S/G
- d. Close TDAFW pump flow control valve to ruptured S/G
~ S/G A, AOV-4297
~ S/G B, AOV-4298
- e. Verify MDAFW pump crosstie valves CLOSED
- d. Dispatch AO with locked valve key to locally close TDAFW pump manual feedwater isolation valve to ruptured S/G.
~ S/G A, V-4005
~ S/G B, V-4006
- e. Manually close valves.
~ MOV-4000A
~ MOV-4000B
à y,l
EOP:
ECA-3. 2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 6 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 4
Check If S/G Secondary Side Is Intact:
o Pressure in both S/Gs STABLE OR INCREASING IF any S/G pressure decreasing in an uncontrolled manner OR completely depressurized, THEN verify faulted S/G isolated unless needed for RCS cooldown:
o Pressure in both S/Gs GREATER THAN 100, PSIG
~ Steamlines
~ Feedlines IF NOT, THEN go to E-2, FAULTED STEAM GENERATOR ISOLATION, Step l.
- x x*************
CAUTION IF CST LEVEL DECREASES TO LESS THAN 5 FEET, THEN ALTERNATE WATER SOURCES FOR AFW PUMPS WILL BE NECESSARY (REFER TO ER-AFW.1, ALTERNATE WATER SUPPLY TO AFW PUMPS).
- x**x***x**
x x*x x x**xx ****x*****x*****
NOTE:
TDAFW pump flow control valves fail open on loss of IA.
5 Monitor Intact S/G Level:
a.
Narrow range level GREATER THAN 5%
[25% adverse CNMT]
- b. Control feed flow to maintain narrow range level between 17%
[25% adverse CNMT] and 50%
- a. Maintain total feed flow greater than 200 gpm until narrow range level greater than 5%
[25%
adverse CNMT] in at least one S/G.
- b. IF narrow range level in the intact S/G continues to increase in an uncontrolled manner, THEN consider isolating unnecessary release paths:
~ TDAFW pump steam supply valves
~ S/G'lowdown valves
~ Refer to Attachment RUPTURED S/G
I
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 7 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED NOTE:
Shutdown margin should be monitored during RCS cooldown; Refer to Figure SDM.
6 Initiate RCS Cooldown To Cold Shutdown:
- a. Establish and maintain cooldown rate in RCS cold legs LESS THAN 100'F/HR b.
Use RHR system if in service c.
Dump steam to condenser from intact S/G
- c. Manually or locally dump steam using intact S/G ARV.
IF no intact S/G available, THEN perform the following:
o Use faulted S/G.
-OR-o IF RHR system NOT in service, THEN use ruptured S/G.
7 Check RCS Subcooling Based On Core Exit T/Cs GREATER THAN O'F USING FIGURE.MIN SUBCOOLING Go to Step 19.
8 Check Safeguards Pump Status o
SI pumps ANY RUNNING Go to Step 15.
-OR-o RHR pumps ANY. RUNNING IN INJECTION MODE
k
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 8 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 9 Place PRZR Heater Switches In The Following Positions:
o PRZR heater control group PULL STOP o
PRZR heater backup group
- OFF CAUTION VOIDING MAY OCCUR IN THE RCS DURING RCS DEPRESSURIZATION.
THIS WILL RESULT IN A RAPIDLY INCREASING PRZR LEVEL.
x **x
- x
- x *******
x *************
x ******
NOTE:
o If auxiliary spray is in use, spray flow may be increased by closing normal charging valve AOV-294 and normal PRZR spray valves.
o When using PRZR PORV, select one with an operable block valve.
10 Depressurize RCS To Refill PRZR a.
Use normal PRZR spray valve associated with running RCP
~ PCV-431A for A RCP
~ PCV-431B for B RCP b.
PRZR level GREATER THAN 13%
[40% adverse CNMT) a.
Use one PRZR PORV.
IF IA NOT available, THEN refer to Attachment N2 PORVS.
IF no PORV available, THEN use auxiliary spray valve.
- b. Continue with Step 11.
WHEN level greater than 13$
(40%
adverse CNMT], THEN stop RCS depressurization.
c.
Stop RCS depressurization
J I
EOP:
ECA-3. 2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 9 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED x x*x*x*x**x***x**x***x x****************
CAUTION IF RCP SEAL COOLING HAD PREVIOUSLY BEEN LOST, THEN THE AFFECTED RCP SHOULD NOT BE STARTED PRIOR TO A STATUS EVALUATION.
x
- x **x x x *x***x****************
11 Check If An RCP Should Be Started:
a.
Both RCPs STOPPED b.
RCS subcooling based on core exit T/Cs GREATER THAN O' USING FIGURE MIN SUBCOOLING a.
Stop all but one RCP and go to Step 12 Go to Step 19.
c.
PRZR level GREATER THAN 13%
(40% adverse CNMT]
- d. Try to start an RCP
- 1) Establish conditions for starting an RCP o
Bus 11A or 11B'energized o
Refer to Attachment RCP START
- c. Return to Step 10.
- 2) Start one RCP
~ v
EOP:
ECA-3.2 SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 10 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 12 Check If One Of Three SI Pumps Should Be Stopped:
a.
Three SI pumps RUNNING b.
RCS subcooling based on core exit T/Cs GREATER THAN 10'F
[10'F adverse CNMT] USING FIGURE MIN SUBCOOLING c.
Check PRZR level GREATER THAN 13%
[40% adverse CNMT) a.
Go to Step 13.
- b. IF RCS hot leg temperatures greater than 320'F [310'F adverse CNMT] OR IF RHR normal cooling in service, THEN go to Step 19.
IF RHR normal cooling NOT in service AND RCS hot leg temperatures less than 320'F
[310'F adverse CNMT], THEN ensure at least one RHR pump running in injection mode and go to Step 12c.
IF no RHR pump can be operated in injection mode, THEN go to Step 19.
c.
Do NOT stop SI pump: Return to Step 10.
d.
Stop one SI pump
EOP:
ECA-3.2 SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 11 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 13 Check If One Of Two SI Pumps Should Be Stopped:
a.
Two SI pumps RUNNING b.
RCS subcooling based on core exit T/Cs GREATER THAN 35'F
[35 'F adverse CNMT] USING FIGURE MIN SUBCOOLING c.
PRZR level GREATER THAN 13%
[40% adverse CNMT) d.
Stop one SI pump a.
Go to Step 14.
- b. IF RCS hot leg temperatures greater than 320'F [310'F adverse CNMT]
OR IF RHR normal cooling in service, THEN go to Step 19.
IF RHR normal cooling NOT in service AND RCS hot leg temperatures less than 320'F
[310'F adverse CNMT], THEN ensure at least one RHR pump running in injection mode and go to Step 13c.
IF no RHR pump can be operated in injection mode, THEN go to Step 19.
c.
Do NOT stop SI pump. Return to Step 10.
EOP ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV'3 PAGE 12 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 14 Check If Last SI Pump Should Be Stopped:
a.
One SI pump RUNNING
- b. Determine required RCS subcooling from table:
- a. IF any RHR pump running in injection mode, THEN go to Step 19.
IF NOT, THEN go to Step 15.
Charging Pump Availability RCS Subcooling Criteria NONE ONE TWO THREE Insufficient subcooling to stop SI pump.
215'F [215'F adverse CNMT]
150'F [150'F adverse CNMT]
80'F [80'F adverse CNMT) c.
RCS subcooling based on core exit T/Cs GREATER THAN VALUE FROM TABLE ABOVE USING FIGURE MIN SUBCOOLING d.
PRZR level GREATER THAN 13%
(40% adverse CNMT]
e.
Stop running SI pump
- c. IF RCS hot leg temperatures greater than 320'F [310'F adverse CNMT]
OR IF RHR normal cooling in service, THEN go to Step 19.
IF RHR normal cooling NOT in service AND RCS hot leg temperatures less than 320'F
[310'F adverse CNMT), THEN ensure at least one RHR pump running in injection mode and go to Step 14d.
IF no RHR pump can be operated in injection mode, THEN go to Step 19.
d.
Do NOT stop SI pump.
Return 'to Step 10.
0
~
JNh
EOP:
ECA-3. 2 SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 13 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 15 Check If Charging Flow Should Be Controlled To Maintain RCS Inventory:
a.
Check RHR pumps RUNNING IN INJECTION MODE a.
Perform the following:
- 1) Control charging flow to maintain RCS inventory:
BETWEEN 68%
AND 73%
[73%
AND 76% adverse CNMT]
-OR-o RVLIS fluid fraction (any RCP running)
BETWEEN 80%
AND 904 2)
Go to Step 16.
b.
Go to Step 19
4
EOP:
ECA-3.2 TITLE:
SGTR WITH, LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 14 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED x*xx***x**x*x*x x x**x***x********x******
CAUTION IF RCP SEAL COOLING HAD PREVIOUSLY BEEN LOST, THEN THE AFFECTED RCP SHOULD NOT BE STARTED PRIOR TO A STATUS EVALUATION.
- x ******
x x *****x*******x*****xx*x% ******
16 Check RCP Status:
a.
- AT LEAST ONE RUNNING a.
Perform the following:
- 1) Establish conditions for starting an RCP:
o Verify bus 11A or 11B energized.
o Refer to Attachment RCP START.
- 2) Start one RCP.
IF an RCP can NOT be started, THEN verify natural circulation (Refer to Attachment NC).
IF natural circulation NOT
- verified, THEN increase dumping steam.
b.
Stop all but one RCP
ll 8
= ~ d f
,n
EOP:
ECA-3.2 ilTLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 15 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED
- x %
- x x x%
x*x**x x**xx* x x***x************
CAUTION o
VOIDING MAY OCCUR IN THE RCS DURING RCS DEPRESSURIZATION.
THIS WILL RESULT IN A RAPIDLY INCREASING PRZR LEVEL.
o IF SI HAS BEEN TERMINATED, THE ACCUMS SHOULD BE ISOLATED PRIOR TO DEPRESSURIZING THE RCS TO LESS THAN 1000 PSIG.
- x x******%*x*******************
NOTE:
o If auxiliary spray is in use, spray flow may be increased by closing normal charging valve AOV-294 and normal PRZR spray valves.
o When using PRZR PORV, select one with an operable block valve.
17 Depressurize RCS To Saturation At Core Exit:
a.
Determine saturation pressure for core exit T/Cs using Figure TSAT b.
Use normal PRZR spray valves associated with running RCP
~ PCV-431A for A RCP
~ PCV-431B for B RCP
- c. Energize PRZR heaters as necessary
- d. Depressurize RCS until EITHER of the following conditions satisfied:
b.
Use one PRZR PORV.
IF IA NOT available, THEN refer to Attachment N2 PORVS.
IF PORV NOT available, THEN use auxiliary'spray valve (AOV-296).
o PRZR level GREATER THAN 75%
[65% adverse CNMT]
-OR-o RCS pressure
- AT SATURATION FROM STEP 17a
0
EOP:
ECA-3.2 SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 16 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 18 Verify Adequate Shutdown Margin
- b. Borate as necessary.
- 19 Monitor SI Reinitiation Criteria:
a.
Core exit T/Cs DECREASING b.
Check RVLIS indication:
o Level (no RCPs)
GREATER THAN 68%
[73% adverse CNMT) a.
Increase dumping steam.
IF core exit T/Cs do NOT
- decrease, THEN manually operate SI pumps as necessary.
- b. Manually operate SI pumps as necessary.
-OR-o Fluid Fraction (any RCP running)
GREATER THAN 80%
EOP:
ECA-3.2 SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 17 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 20 Check If SI ACCUMs Should Be Isolated:
a.
RCS subcooling based on core exit T/Cs GREATER THAN O' USING FIGURE MIN SUBCOOLING b.
PRZR level
- GREATER THAN 5%
(30% adverse CNMT)
- a. IF both RCS hot leg temperatures less than 400'F, THEN go to Step 20c.
IF NOT, THEN go to Step 21.
- b. Return to Step 10.
~ MOV-841, MCC C position 12F
~ MOV-865, MCC D position 12C
- d. Close SI ACCUM discharge valves
~ MOV-841
~ MOV-865
- d. Vent any unisolated ACCUMs:
1)
Open vent valves for unisolated SI ACCUMs.
- e. Locally reopen breakers for MOV-841 and MOV-865
~ ACCUM A, AOV-834A
~ ACCUM B, AOV-834B
- 2) Open HCV-945.
~
C
'4 I
EOP:
ECA-3 '
TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 18 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 21 Check If Emergency D/Gs Should Be Stopped:
- a. Verify AC emergency busses energized by offsite power:
o Emergency D/G output breakers OPEN
- a. Try to restore offsite power (Refer to ER-ELEC.1, RESTORATION OF OFFSITE POWER).
o AC emergency bus voltage GREATER THAN 420 VOLTS o
AC emergency bus normal feed breakers CLOSED
- b. Stop any unloaded emergency D/G and place in standby (Refer to Attachment D/G STOP) 22 Minimize Secondary System Contamination:
- a. Isolate reject from hotwell to CST:
o Place hotwell level controller (HC-107) in MANUAL at50'.
IF hotwell level increasing, THEN direct HP to sample hotwells for activity.
o Verify hotwell level STABLE
- b. Verify local actions to complete isolation of ruptured S/G (Refer to Attachment RUPTURED S/G)
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF. REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 19 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 23 Verify Adequate SW Flow To CCW Hx:
- a. Verify at least two SW pumps RUNNING
- b. Verify AUX BLDG SW isolation valves OPEN
~ MOV-4615 and MOV-4734
~ MOV-4616 and MOV-4735
- a. Manually start pumps as power supply permits (258 kw per pump).
IF less than two SW pumps can be operated, THEN go to Step 24.
- c. Verify CNMT RECIRC fan annunciator C-2, HIGH TEMPERATURE ALARM -
EXTINGUISHED
24 Check RCP Cooling a.
Check CCW to RCPs Establish normal cooling to RCPs (Refer to Attachment SEAL COOLING).
o Annunciator A-7, RCP 1A CCW RETURN HIGH TEMP OR LOW FLOW EXTINGUISHED o -Annunciator A-15, RCP 1B CCW RETURN HIGH TEMP OR LOW FLOW EXTINGUISHED b.
Check RCP seal injection o
Labyrinth seal D/Ps GREATER THAN 15 INCHES OF WATER
-OR-o RCP seal injection flow to each RCP GREATER THAN 6 GPM
'h
EOP:
ECA-3.2 ijTLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 20 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 25 Check If Seal Return Flow Should Be Established:
- a. Verify instrument bus D
ENERGIZED
- b. Verify RCP Pl seal outlet temperature LESS THAN 235'F
- c. Verify RCP seal outlet valves OPEN
~ AOV-270A
~ AOV-270B
- d. Reset both trains of XY relays for RCP seal return isolation valve MOV-313 e.
Open RCP seal return isolation valve MOV-313
- f. Verify RCP 01 seal leakoff flow LESS THAN 5.5 GPM
- g. Verify RCP 41 seal leakoff flow GREATER THAN 0.25 GPM a.
Perform the following:
- 1) Ensure steam dump mode control in MANUAL'.
b.
Go to Step 26.
- c. Manually open valves as necessary.
e.
Perform the following:
- 1) Place MOV-313 switch to OPEN.
- f. IF any RCP seal leakoff flow greater than 5.5 gpm THEN:
o Close the affected RCP seal discharge valve
~ RCP A, AOV-270A
~ RCP B, AOV-270B o
Trip the affected RCP IF both RCP seal discharge valves are shut, THEN go to Step 26.
- g. Refer to AP-RCP.1, RCP SEAL MALFUNCTION.
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 21 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED NOTE:
Adverse CNMT conditions or loss of forced air cooling may result in failure of NIS detectors.
26 Check If Source Range Detectors Should Be Energized:
a.
Source range channels DEENERGIZED a.
Go to Step 26e.
b.
Check intermediate range flux-EITHER CHANNEL LESS THAN
'0 10 AMPS
- b. Perform the following:
N
- 1) IF neither intermediate range channel is decreasing, THEN initiate boration.
- 2) Continue with Step 27.
WHEN flux is LESS THAN 10 amps on any operable
- channel, THEN do Steps
- 26c, d and e.
c.
Check the following:
o Both intermediate range channels LESS THAN 10-10 AMPS
- c. Continue with Step 27.
WHEN either condition met, THEN do Steps 26d and e.
-OR-o Greater than 20 minutes since reactor trip
- d. Verify source range detectors ENERGIZED
- d. Manually energize source range detectors by depressing P-6 permissive defeat pushbuttons (2
of 2).
IF source ranges can NOT be
- restored, THEN refer to ER-NIS.1, SR MALFUNCTION and go to Step 27.
- e. Transfer Rk-45 recorder to one source range and one intermediate range channel
EOP l ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 22 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 27 Establish Normal Shutdown Alignment:
a.
Check condenser
- AVAILABLE
- a. Dispatch AO to perform Attachment SD-2.
- b. Perform the following:
o Open generator disconnects
~ 1G13A71
~ 9X13A73 o
Place voltage regulator to OFF o
Open turbine drain valves o
Rotate reheater steam supply controller cam to close valves o
Place reheater dump valve switches to HAND o
Stop all but one condensate pulllp
- c. Verify adequate Rx head cooling:
Go to Step 28.
- 2) Verify at least one control rod shroud fan RUNNING
- 2) Manually start one fan as power supply permits (45 kw)
- 3) Verify one Rx compartment cooling fan RUNNING
- 3) Perform the following:
o Dispatch AO to reset UV relays at MCC C and MCC D.
o Manually start one fan as power supply permits (23 kw).
- d. Verify Attachment SD-1 COMPLETE
J
~
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 23 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED x ****x ****4'***********
CAUTION FEED FLOW SHOULD NOT BE ESTABLISHED TO ANY RUPTURED S/G WHICH IS ALSO FAULTED UNLESS IT IS NEEDED FOR RCS COOLDOWN.
- x
- x ********
x **x x x
- x x
- x
- x ********
x x ******
- 28 Monitor Ruptured S/G(s)
Narrow Range Level GREATER THAN 17%
[25% adverse CNMT]
Refill ruptured S/G to 67%
[55%
adverse CNHT] using feed flow.
IF either of the following conditions occurs, THEN stop feed flow to ruptured S/G.unless needed for RCS cooldown:
o Ruptured S/G pressure decreases in an uncontrolled manner.
-OR-o Ruptured S/G pressure increases to 1020 psig.
- 29 Monitor RCP Trip Criteria:
a.
RCPs ANY RUNNING b.
Check the following:
o RCP 41 seal D/P LESS THAN 220 PSID a.
Go to Step 30.
b.
Go to Step 30.
-OR-o Check RCP seal leakage LESS THAN 0.25 GPM c.
Stop affected RCP(s)
EOP:
ECA-3.2 SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 24, of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED 30 Check Condenser Steam Dump Available CONDENSER VACUUM GREATER THAN 20 INCHES HG Use intact S/G ARV for RCS temperature control.
31 Check If RHR Normal Cooling Can Be Established:
a.
RCS cold leg temperature LESS THAN 350'F a.
Go to Step 32.
b.
RCS pressure LESS THAN 400 psig (300 psig adverse CNMT)
- c. Place letdown pressure controller in MANUAL CLOSED b.
Go to Step 32.
d.
Check following valves OPEN
~ AOV-371, letdown isolation valve
~ AOV-427, loop B cold leg to REGEN Hx
~ At least one letdown orifice valve (AOV-200A, AOV-200B, or AOV-202)
- d. Perform the following:
- 1) Reset both trains of XY relays for AOV-371 and AOV-427.
- 2) Open AOV-371 and AOV-427
- 3) Open one letdown orifice valve.
- e. Verify pressure on PI-135 LESS THAN 400 PSIG e.
Go to Step 32.
- f. Place RCS overpressure protection system in service (Refer to 0-7, ALIGNMENT AND OPERATION OF THE REACTOR VESSEL OVERPRESSURE PROTECTION SYSTEM)
EOP:
ECA-3.2 SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 25 of 25 STEP ACTION/EXPECTED RESPONSE
RESPONSE
NOT OBTAINED NOTE:
This procedure should be continued while obtaining CNMT hydrogen sample in Step 32.
32 Check CNMT Hydrogen Concentration:
- b. Hydrogen concentration LESS THAN 0.5%
33 Check Core Exit T/Cs' LESS THAN 200'F Return to Step 2.
34 Evaluate Long Term Plant Status:
- a. Maintain cold shutdown conditions
- b. Consult TSC
-END-
C I
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 1 of 1 ECA-3.2 APPENDIX LIST TITLE PAGES 1)
RED PATH
SUMMARY
2)
FIGURE MIN SUBCOOLING 3)
FIGURE SDM 4)
FIGURE TSAT 5)
ATTACHMENT SFP-RWST 6)
ATTACHMENT N2 PORVS 7)
ATTACHMENT NC 8)
ATTACHMENT SEAL COOLING 9)
ATTACHMENT RCP START 10)
ATTACHMENT D/G STOP 11)
ATTACHMENT AUX BLDG SW 12)
ATTACHMENT RUPTURED S/G 13)
ATTACHMENT SD-1 14)
ATTACHMENT SD-2 15)
ATTACHMENT RHR COOL 16)
FOLDOUT
i yl
EOP:
ECA-3.2 iITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 1 of 1 RED PATH
SUMMARY
a.
SUBCRITICALITY Nuclear power greater than 54 b.
CORE COOLING Core exit T/Cs greater than 1200'F
-OR-Core exit T/Cs greater than 700'F AND RVLIS level (no RCPs) less than 434
[464 adverse CNMT]
c ~
d.
HEAT SINK Narrow range level in all S/Gs less than 5%
(25% adverse CNMT] AND total feedwater flow less than 200 gpm INTEGRITY Cold leg temperatures decrease
.greater than 100'F in last 60 minutes AND RCS cold leg temperature less than 285'F e.
CONTAINMENT CNMT pressure greater than 60 psig
EOP:
ECA-3. 2 TITLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV:
13 PAGE 1 of 1
FIGURE MIN SUBCOOLING NOTE:
Subcooling Margin = Saturation Temperature From Figure Below (-] Core Exit T/C Indication S
PRESSURE (PSIG)
RC 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 A
500 400 300 200 100 0
20 RCS PRESSURE INCREMENTS 20 PSIG SUBCOOLED REGION INADEQUATE SUBCOOL ING REGION DVE E
C NMT RS TEMPERATURE INCREMENTS 10'F NORMAL CNMT 0
250 300 350 400 450 500 550 600 650 700 CORE EXIT SATURATION TEMPERATURE ('F)
EOP:
ECA-3.2 T!TLE:
SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED FIGURE SDM REV 13 PAGE 1 of 1 NOTE:
o Curve includes allowance for one stuck rod.
Add 100 ppm for each additional stuck rod.
o To obtain core burnup, use PPCS turn on code BURNUP.
BORON CONCENTRATION (PPH) 1800 1600 BORON INCREMENTS 20 PPH 1400 1200I oooo ADEQUATE SDM 100 PPM CONSERVATISM INCLUDED 800 600 400 BORATE 200 BURNUP INCREMENTS 100 MWD/MTU 0
1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 11000 12000 CYCLE 24 BURNUP (HWD/MTU)
r
~v n
1 yX EOP:
ECA-3. 2 iITLE:
.SGTR WITH LOSS OF REACTOR COOLANT SATURATED RECOVERY DESIRED I
REV:
13 PAGE 1 of 1 FIGURE TSAT SAT 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0
URATION PRESSURE (PSIG)
PRESSURE INCREMENTS 20 PSIG TEMPERATURE INCREMENTS 10'F 200 250 300 350 400 450 500 550 600 650 700 CORE EXIT SATURATION TEMPERATURE (')
(
EOP:
ECA-3.2 TITLE:
SGTR WITH LOSS'OF REACTOR COOLANT SATURATED RECOVERY DESIRED REV 13 PAGE 1 of 1 SI REINITIATION CRITERIA FOLDOUT PAGE IF EITHER condition listed below occurs, THEN manually operate SI pumps as necessary:
o Core exit T/Cs
INCREASING
-OR-o Check RVLIS indication:
Level (no RCPs)
LESS THAN 68%
[73% adverse CNMT]
Fluid fraction (any RCP running)
LESS THAN 804 2.
SECONDARY INTEGRITY CRITERIA IF any S/G pressure is decreasing in an uncontrolled manner or is completely depressurized, and has not been isolated, THEN go to E-2, FAULTED S/G ISOLATION, Step 1, unless faulted S/G needed for RCS cooldown.
3.
COLD LEG RECIRCULATION SWITCHOVER CRITERION IF RWST level decreases to less than 28%,
THEN go to ES-1.3, TRANSFER TO COLD LEG RECIRCULATION, Step 1.
4.
AFW SUPPLY SWITCHOVER CRITERION IF CST level decreases to less than 5 feet, THEN switch to alternate AFW water supply (Refer to ER-AFW.1, ALTERNATE WATER SUPPLY TO AFW PUMPS).
4 1
r 0