ML18019A787
| ML18019A787 | |
| Person / Time | |
|---|---|
| Site: | Harris |
| Issue date: | 12/04/1984 |
| From: | CAROLINA POWER & LIGHT CO. |
| To: | |
| Shared Package | |
| ML18003B224 | List: |
| References | |
| EOP-EPP-004, EOP-EPP-4, NUDOCS 8605010207 | |
| Download: ML18019A787 (29) | |
Text
EOPHP3 CAROLINA.POWER & LIGHT COMPANY SHEARON HARRIS NUCLEAR POWER PLANT PLANT OPERATING MANUAL VOLUME 3 PART'.
PROCEDURE'YPE':.
EMERGENCY OPERATING PROCEDURE'EOP)
END PATH PROCEDURE (EPP)
NUMBER:,
EOP-EPP-~
TITLE',
.. e.'EACTOR, TRIP'ESPONSE REVISION 0 APPROVED SIGNATURE DATE TITLE POR A
8~0SO~oi0~ 8~0 F
OOC~ 0~000+00 428 PDR Page 1 of 13 I
PATH-1 44r 4
A.C I Arl IUI
~
~IL i~tAs vo oto ~IAL' lot autLLl~
LL 44 L rtLDOII A IVWQV~o
~ IIVWWW IWI W WVI OW WWO ~
WI BIJOU w vw'Io ~
~ WO W U U~ U iAO UO OVVOOVNO WV ~ V OOI IOh,
~ V IW I ~ IIU
~ IVO V WWOI WOO W 'U ~
U V U WW ~
QCWU It
~ I
~
IILIKI/t~
I
~
~
IU IW N 'h WLOWWOV w
AIL oo&~ w Iv Uw TgrorttL 1tt. 'L4j m%ÃLL K-'IK ALL~
47Ã EN~M o
'LA+PA IL SAL a
~ WWIIOWWIO OWO W IVO I I OVOIW OVO IWo
~OWVU WO IW MI W IOW I I UO lt IUU IUO
~
~
gOPHP3 0
LIST OF EFFECTIVE PAGES
~Pa e
Revision No.
1 through 13.
0 EOP-EPP-4 Rev; 0
Page 2 of 13
EOPHP3 REACTOR TRIP RESPONSE i31.0 PURPOSE
~
~
~"
.This procedure provides the necessary instructions to stabilize and control the plant folloving a reactor trip vithout k safety injection..
2.0 OPERATOR ACTIONS'.
CAUTION If SI actuation.. occurs't= any. time, immediately go to PATH>>l,, entry point A.
NOTE" Fo1dout= D should: be. open EOP-EPP Rev.. 0 Page 3 of l3
1 1 4 I
p -r
EOPHP3 REACTOP, TRIP
RESPONSE
Instructions Res onse Not Obtained 1.
Check RCS Temperature STABLE AT OR TRENDING TO 557F'F temperature less t S
decreasing, THEN:
hen 557'F and a.
Stop-dumping-steam.
b IF'ooldown continues, THEN contro3 total feed flow.
Maintain total feed flow, greater than. 400 GPM or 192 KPPH until level greater than 10K in at'east.
one S/G.
c:
IF'ooldown: continues, THEN close MSIVs and bypass valves.
IF: temperature. greater than 557'F and increasing;,
THEN:
II o 'ump steam to condenser.
OR' Dump steam. using S/0 PORVs.
EOP.-EPP-4 Rev..
0.
Page 4 of 13
~
~
~
IC EOPHP3 REACTOR TRIP RESPONSE Verify At Least One RCP - RUNNING Perform the following:
o Place steam dump in pressure control mode.
o Dump steam to establish natural circulation.
3.
Check Feed System Status:
a; Check. RCS'emperature:
LESS'HAN, 564'F a-Continue. with step 4.
WHEN RCS temperature less than 564'F, THEN do steps.3b and c.'
Verif'y. feed regul'ator va1ves:
- CLOSED, c..
EstabTfsh, FR'ypass EXo~ to S:/Gs c.
Establish; AFV'low to S'/Gs..
~
P ~
e EOP-EPP-4'ev, 0
Page 5 of 13
%I i+ t%
It R
lt' l
~
U
EOPHP3 REACTOR TRIP
RESPONSE
4.
Verify All Control Rods Fully Inserted.
IF two or more control rods NOT fully
- inserted, THEN emergency borate as follows:
a.
Start a boric acid pump.
b.
Align boric acid to CSIP suction (listed in order of preference).
o Open 8104 (Emergency'oration)
OR o
Open FCV-113A (Boric Acid to Blender) and..open FCV-113B 0
~
(Blender Outlet to CSIP suction)
OR Open. FCV-113K (Bpric Acid to Blender) and open FCV-1.14A (Blender, Outlet to, VCT) c;.
Verify boric. acid. flow to CSIP
~ suction;.
Verify CSIP flow to RCS.
EOP-EPP-4 Rev.
0 Page 6 of 13
~
~
@type ~t a P
k
~ 'OPHP3 REACTOR TRIP
RESPONSE
5.
Check PZR Level Control:
a.,
Level GREATER THAN 17K a..
Perform
.. following:
1)
Verify letdown isolation.
2)
Verify PZR heaters secured.
3)
Control charging to restore PZR level greater than-17K.
b Ver'ify charging and. letdown.
IK SERVICE.
c..
Level STABLE AT OR; TRENDING c.,
Control'harging and letdown to TO 25K maintain PZR level at 257.'.
6:
Check PZR Pressure.
ControT a
Pressure GREATER THAN'881.
PSIG:
a Verify SI actuation.
AND go to PATE-1:, entry-point A.
EOP-EPP Rev 0
Page 7 of 13
t, u H A
~ l',. ~~
a <<'< g em P
EOPHP3 REACTOR TRIP RESPONSE
'b.,
Pressure STABLE AT'R TRENDING TO 2235 PSIG b.
IF pressure LESS THAN 2235 PSIG and decreasing, THEN:
1)
Verify PZR PORVs closed.
2)
IF. any PZR PORV can NOT be
- closed, THEN close its block valve.
~
Ver'ify PZR spray valves closed~/
IF valve(s) can NOT be
- closed, THEN stop RCP(s) supplying failed spray valve(s).
3)
Verify'ZR heaters energized.,
IF-pressure greater. than 2235 PSIG and. increasing;.
THEN:
1)
Verify PZR heaters off.
2)
Control pressure using-normal'ZR. spray IF NOT available: AND letdown, in service,,
THEN use. auxiliary spray IF'OT, THEN use one PZR; PORV; EOP-EPP-4 Rev.
0 Page 8 of 13
4
~
~
~
p ~
4
I EOPHP3 C
Ig 7..
Check S/G Levels:
RESPONSE
a.
Narrow. range level GREATER THAN 10X a.
Maintain total feed flow greater than 400 GPM or 192 KPPH until narrow range level greater than 10X'n at least one S/G.
b.-
Control. feed flow to maintain.
narrow: range; level'etween..
10X'nd, 50X; b.
IF narrow range. level in any S/G continues to increase, THEN stop feed flow. to that S/G.
EOP-EPP-4 Rev; 0
Page 9 of 13
'D, hh Pgt
~ 1&CWL~ "u h
'e
~ t 5
~ EOPHP3 REACTOR TRIP RESPONSE 0,
8.
Verify All AC Busses ENERGIZED Perform the fol3owing as necessary:
%~
BY OFFSITE POWER a.
Verify EDGs have started.
b.
Verify EDGs have assumed the proper loads.
c.,
Verify turbine DC lube oil pump and air'ide seal oil backup pump are: running.
Verify adequate EDG capacity and load the following equipment on the. EDGs:.
1)
One instrument air
.compressor 2')
Battery chargers 3)
PZR. heaters,.
as needed.,
e.,
Determine the cause of the loss of offsite power., If due to a failure-of the: startup transformer,.
request; assistance from. maintenance crews to restore 4
power from: either the main or spare startup transformer.. If the loss'f power is the result of a loss, of; grid, obtain assi'stance-.from.
the Load Dispatcher..
9..
Transfer C'ondenser steam, Dump to Pressure Control Mode.
$ )
IF condense<
NO+" available,.
THEN use
~
le S/G-'ORVs'.
EOP-EPP-4 Rev.
0 Page 10 of. 13
Ap 4
~+<a ~
~ M II
gOPHP3 i'EACTOR TRIP
RESPONSE
e,~C~'
CAUTTON On natural circulation, RTD bypass temperatures and associated interrocts will be inaccurate..
NOTE:
RCPs shoul'd be run in order of priority to provide normal PZR spray.
10..
Check. RCP Status AT LEAST ONE RUNNING Try to start one RCP:
a Establish conditions for running RCP(s) using OP-100, "REACTOR COOLANT SYSTEM," while. continuing with. this, procedure..
b 'tart'CP(s)
IF at. least one-RCP can NOT be stamped.,
THEN verify natural c&culation from; trended values:
o RCS'ubcooling GREATER THAN 25 F o
Steam; pressure. - STABLE OR DECREASING..
o RCS: hot, leg temperature STABL'E OR DECREASING; o.
Core exit T/Cs STABLE OR DECREASING o
RCS.cold: leg-temperatures TRENDING'O OR. AT SATURATION TEMPERATURE FOR'TEAM PRESSURE.
~ 4w.
IF natur~ circulation NOT'erified, THEN increase.
dumping steam.
EOP-EPP Rev.. 0 Page. Ll of 13
C II7ICE 4
~
EOPHP3 REACTOR TRIP RESPONSE I
11.
Check If Source Range Detector Should Be Energized:
a.
Check intermediate range flux
- LESS'HAN 10 AMPS a.
Continue with step 12.
WHEN flux
-10 less than 10
- AMPS, THEN do steps 10b and c.
b.
Verify source range detector's ENERGIZED c..
Transfer nuclear recorder'o source. range scale.
12.
Shutdown. U Equipment=
0:
o.
Stop; bottr. heater drain. pumps Stop.. condensate
- pump, condensate. booster pump and:
EW'ump='as; required.
o Isolate BTRSerify turbine generator goes.,
on-. the turning: gear; one-minute after zero, speed. alarm.
is: received-:
o, Secure. the. MSRs o
Stop DEK pumps EOP-EPP-4 Rev..
0 Page 12 of 13
~ g
'~ r
~
~ ~'r
't
>Kwl 3
Cigar
P 4
EOPQP3
\\
REACTOR TRIP RESPONSE 13.
Maintain Stable, Plant Conditions:
a.
PZR pressure - AT OR TRENDING TO 2235 PSIG b..
PZR level AT OR TRENDING TO 25X' S/G'arrow.range levels BETWEEN 10X: AND 50X'.
RCS average temperature-AT'R TRENDING'O 557'F 14-Go: To Appropriate Pl'ant Procedure:
I As; Determined'. Below."
a Perform:
OMM-004-"POSZ'RIP'/SAZEGUARDS-REVIEW" b 'heck plant. status RCS COOLDOWN: REQUIRED b.,'o to GP-'04, "RECOVERY FROM' REACTOR'RIP," and return to power operation..
c Check RCP'tatus A'Z LEAST'NE RCP AVAIMKE.
c..
Go to EPP-5, "NATURAL CIRCgLATION COOLDOWN," step 1..
"REACTOR COOLANT: SYSTEM."'
Go to. GP'OT"NORMAL PLANT'OOLDOWN n 0-FINAL PAGE Pane 13 of 13
~
~
'I V
AI u'
II C
I'
~
~ i II
EOPHP3 FOLDCUTS
'c(
FOLDOUT D a.
SI ACTUATION CRITERIA detente SI end go to PATH-1, entry point A f ElTHER co"..d-.'or. lie."'c belov occurs:
1)
RCS Subcoollng LESS THAN 25'F [30'F]
2)
PZR Level CANNOT BE MAINTAINED GREATER THAN 10'~ [45X]
b.
LOSS OF EMERGENCY'OWER Go to EPP>>.1, "LOSS OF AC POWER TO lA-SA AND 1B-SB BUSSES," step 1 'f emergency busses 1A-SA and 1B-SB are deenergzied.
EOP-FOLDOUT Rev.
0 Page 7 of 13
0 F
t A.
~F4 K
e r
4p
.a 0 L
D G
PATH 1
4 I
I W IV
~MARCH HA>>II~ MICLSAR MSGR PLANT IGVZSICN stfaurua I
I
~
~
M 1 A.C. I O/I I M I
GLC Njavtgg a.c..
0/
TrTLEt TfDII la TI wM I ~ I
~I I
M 0
I FOLDOUT R 4
RCP TRIP CRITEIIIA TRIP ALL RCP IP OOTN CO>>IITIIMS LISTED OELolt AIM IRT I
CSIP AT LEAST ua HlatilMI
- 2. Rcs pREsslAM - LEss THAN 1500 psla c lsoo psliD 0
Sl TuailNAT ION CR! TERIA I
I I
fl 4 M ao ro Epp-0 si vsRI owvNM lr ALL cctofrfcfa LISTED SZLI>> occur IIM - fatrATER ftfAN a P cso rr 2
NARRON RAMM LEVEL IN Ar LEAST Ofa IHTACT S/0 " SIMATER IWI loa C40Xl t>>
TOT>>.
PEEO PLOU To INTACT 0/0 OREI TEli TWIN 400 OPtl OR 102 RPPH 5.
RC5 PRE55UHE - STASLE CR INCREASII43 4, I'ZR LEVEL MKIITEN THAH lait I4010 C
COLO LEO RECIRCILATIIM SIIITCHOVPZI DUTEIIION
~
I 00 To ZPP I 0 TRANSI'ER To COLO LES IMCIRCIEATICN ~ STEP I IP RitST LEVEL OECREIISES To LESS THAH LATER 0
SECotOARY INTESRITY CRITEIIIOH 00 To EPP 14, PISLTEO 5TEAII 0ENEIIATOR ISOLATICN, STEP I It'NY 5/0 PRESMIM wia 'of OEEH 150uiTES OECIIEASES IN AN LliCONTIEELEO IIAMMR Oi HAS COHPLETELY OEPIMSSLRIZEO ZZZZ E
LOSS CP EtERSENCY POIIBI 00 To EPP 1
LOSS CP AC POIIER To IA.SA A141 IS 50 SUSSES STEP I Il ENEROTNCY SIMSES iA.SA>>D ia-sa>>M CEENERarzso Hvlrl/0 SSTR ISOLATlaa 00 To EPP-10 SOTR ISOLATION, STEP I
H ANY S/0 LEVEL INCREASES IH AN UNCONTIIOLLEO IIAtosa OR ANY 0/0 HAS A!MOMIALIIAOIATICNLEVELS nt I~
I Hi E
14 N
Gw \\BI ~
Yl H. I 4
IM EP12 10 II IM I
IHI
~ 4 THIS PROCEDURE CLRRENTLY DOES NOT CONTAIN ALL NECESSARY INPOIOIATTON, REOUIRED IHPOISMTION MIST OE TILLED IN PRIOR TO PLANT TUEL LOAD G