ML19224B017
| ML19224B017 | |
| Person / Time | |
|---|---|
| Site: | Crane  |
| Issue date: | 08/30/1978 |
| From: | Metropolitan Edison Co |
| To: | Mullinix W NRC/IE |
| References | |
| 2303-M27A-B-04, 2303-M27A-B-4, TM-0051, TM-51, NUDOCS 7906130435 | |
| Download: ML19224B017 (19) | |
Text
.
x TMI DOCLHEh"rs
[df'(([
DOCUMENT NO:
,f OF DOCUMENT PROVIDED 3Y E ON FZTROPOLITA'i EDISON COMPMTI.
8 Wilda R. Mullinix, NRC 790613043s Of 181 190
+,
\\
. CON 7e ni ! n r"CDY
'\\J' 2303-M27A%PR 2 3 :979
- ~E Fil a=4si= 4 x CB'TRAI C8/30/78 6l/
1, THREE MILE ISLAND NUCLEAR STATION UNIT #2 SURVEILLANCE PROCECURE 2303-M27A/S MOTOR CRIVEN EMERGENCY FEEDPUMP FUNCTIONAL TEST AND VALVE OPERABILITY TEST Table of Effective Pages Pace Cate R evision Pace Date Revis;on Pace Date R evision 1.0 12/01/77 1
26.0 51.0 2.0 12/01/77 1
27.0 52.0 3.0 0904/73 3
28.0 53.0 4.0 C5/C4/78 3
29.0 54.0 5.0 C5/;:/73 3
30.0 55.0 6.0 C5/0a/73 3
31.0 56.0 7.0 03/30/78 a
32.0 57.0 8.0 05/Ca/73 3
33.0 58.0 9.0 03/20/73 4
34.0 59.0 10.0 C5/C /78 3
35.0 60.0 11.0 C5/20/73 4
36.0 61.0 12.0 i:,'cl/77 1
37.0 ti2.0 13.0 C5/: /78 3
38.0 S3.0 14.0 C 5/20,'7 5 39.0 64.0 15.O i :,':1/ 77 40.0 65.0 16.0 5/ :/73 3
41.0 66.0 7.3 CE/20/73 4
42.0 67.0 13.0 C3/20/73 43.0 68.0 15.5 44.0 69.0 20.0 45.0 70.0 21.0 46.0 71.0 22.0 47.0 72.0 23.0 48.0 73.0 24.0 49.0 74.0 25.0 50.0 75.0 Unit 1 S:sfi Reccmmencs Approval Unit 2 Staff Recommends Approval
.j
/s,' - - 7/I Date Approval
/hE/
Date Appecval Ca;nirant Cept. Head C gnizan: Dept. Head Unit 1 PORC Recommends Approval Unit 2 PORC Recommends Approval
/
,k [
hv Date 7 b c
/2
/
Cate
-' S Chairr.an ;f PO RC v'-Chairman of FORC Um: 1 Sucerinte-can: Apcroval Unit 2 Superintencent Acproval l-A,A IA.
'/
is Date T
Da:e Manager Generat on Cuality A urance Apprcval NI Date i
- 9 3
) c))
n,, ~ ~ ~
$$l 2303-M27//B APR 2 3 sap
.evision 1 12/01/77 THREE MILE ISLAND NUCLEAR STATICN h
UNIT !2 SURVEILLANCE PROCECURE 2303-M27A/3 MOTOR ORIVEN EMERGENCY FEEDPUMP i
FUNCTIONAL TEST AND VALVE OPERABILITY TEST NOTE:
2303-M27A includes pump and valve testing, 2303-M27B includes pump testing only.
1.0 PURPOSE 1.1 To insure compliance with Technical Specification 4.0.5 wnich references ASME Section XI for testing of purps.
ASME Section XI specifies test quantities to be measured and acceptable ranges for those quantities.
1.2 To insure coroliance with TMI Unit d2 Technical S;ecifications, St.ction
- 0.5.a, wnich states:
Inservice testing of ASME Code Class i, 2, anc 3 pumps and valv's shall be performed in accordance with Section XI of the ASME Boiler and Pressure Vessel Code and applicable addenda as required by 10 CFRSO, Section 50.SSa(g).
The above inservice testing will confirn the c;eration of the follcwing ASME Code Class 3 valves:
EF-Vi A and B and EF-V27 A anc B and EF-V2 (CLCSED) 2.0
??LICABLE SURVEILLANCE FRECUENCY AND "CCES 2.1 Surveillance Frequency --
31 days (M) for the pump tests (2303-M275) 92 days (Q) for the valve tests (2203-M27A)
NOTE:
Subsection 6.1 of this precedure includes both valve and pump testing: subsecticn 6 2 includes pump testing cnly.
If 2202-127? and 22C2-M273 3gi i92 10
t'
()
2303-M27A/S APR 2 3 g Revision 1 12/01/77 are both scheduled on the Weekly Checklist Master Schedule, perform subsection 6.1 only.
If only 2303-M273 is scheduled perform subsection 6.2'only.
All of the steps in 6.2 are included in 6.1.
2.2 Modes
1 thru 4 - Testing required per ASME Section XI.
5 and 6 - Testing optional per ASME Section XI.
3.0 LIMITS AND PRECAUTIONS 3.1 When a reference value or set of values may have been affected by recair or routine servicing of the pump, a new reference value or set of values shall te determined, or the previcus value reccnfir ed by an inservice test run prior to or within 96 hours0.00111 days <br />0.0267 hours <br />1.587302e-4 weeks <br />3.6528e-5 months <br /> af ter return of the pumo to nor al service.
Ceviations between the crevicus and new set of reference values shall be identified and verification that the new values represent acceptable pumo cperation shall be placed in the Technical Specifiuations surveillance file for that pump.
3.2 An inservice test shall be run en each pump nominally each month during nor-.al plant operation.
It is reccm. mended that this test f equency be maintained during cold shutdown periods where this can reasonably be acccmplished, although this is not mandatory.
3.3 pumps that are cperated more frequently than every mcnth need not be run er stopped for a s::ecial test provided the quantities specified were measured, cbserved, and analyzed.
3.4 All test data must be analyzed within 96 hours0.00111 days <br />0.0267 hours <br />1.587302e-4 weeks <br />3.6528e-5 months <br /> af ter test conpleticn.
3.5 Eearing tem;:eratures are cnly recuired to be reasured cnce every year. When measurement of bearing temperature is not required, 181 193 2o
W e
~
h '/ APR 2 3 39 2303-27A/B
\\
Revision 3 05/04/78 each pump shall be run for at least five minutes under conditions as stable as the system permits. At the end of this time at least one measurement of each of the quantities specified shall be made and recorded.
3.6 The vibration prcbe must be placed in the same position each test to insure repeatable measurements.
3.7 Record identification of the instruments used on the Data Sheet.
3.3 Instruments used for measuring quantities shall not have o scale range exceeding four times the reference value.
3.9 If a valve is ir, an out of service system, it neec not be exercised until immediately prior to return of the system to service.
3.10 Af ter a valve o-its control system has either been replaced, re;: aired, or has undergone maintenance that could affect its performance, and prior to the time it is returned to service, it shall be tested as necessary to demonstrate that the performance parameters which could be affected arc within acceptable limits.
Adjustment of stem packing; removal of ths bonnet, stem assembly, or actuator; or
- isconnection of hydraulic or electrical lines are exampies of maintenance tnat could affect valve performance parameters.
4.C
_ :C::'4 :: 5Y3 TEM 41 I. e gency fecater pumps are located in the Control Building Area, C ava ticn 230'6".
4.2 C:r.:rols for the emergency feedwater pumps are located in Control Recm on Panel 4.
Local controls are also available.
5.0 ECUIPMENT RECUIRED 5.1 IRD Vibration Analyzer, Model 306, or equivalent.
5.2 Eagle Eye Me.er, Mcdel 77C,1 1.5% full scale, 0-50 ir.ches of water or equivalent.
{
PR 2 3 1973
?303-M27A/3 Revisien 3 05/04/78 Stepwatch - required cnly if 2303-M27A is scheduled.
5.3 6.0 PROCEDUR[
The following procedure may be used for Motor Driven tiOTE:
Emergency Feedpump 2A or 23. Those components designations in (parenthesis) refer to the 3 system.
Subsection 6.1 includes both valve and pump testing; NOTE:
If 2303-M27A subsection 6.2 includes pump testing only.
and 2303-M273 are both scheduled on the 'Jeekly Checklist Master Schedule, perform subsection 6.1 only.
If cnly All 2303-M273 is schedulec perform subsection 6.2 cnly.
of the steps in 6.2 are included in 6.1.
Initial Each Step Af ter Satisfactory Completion.
6.1 Energency Feed Pump (EF-PZA(S)) and valve test.
IiSTALL Eagle Eye Meter er ecuivalent at CO-FE-7616 6.1.1 (7617).
6.1.2 PERFORM Appendix A (3) Valve Line up.
RECCRD on Data Sheet A (3) the pump idle inlet pressure 6.1.3 from CO-PI-2025 (2026).
I!iSURE Proper lube oil level on pump frem bearing sight 6.1.4 glasses and I:lITIAL Data Sheet.
Frcm its lccal control switch, OPEft EF-V-27A(3) and time 6.1.5 from when the open button is pressed until only the red Record time on open light is illuminated on the panel.
Data Sheet A(3).
6.i.6 CLOSE EF-V27A(3).
W 181 195 4.0
f g
'APR 2 3 7379 2303-M27A/S Revision 3 05/04/73 6.1.7 START EF-P-2A (B) frcm Panel 4.
6.1.8 INSURE EF-V27A (S) autcmatically opens.
6.1.9 THROTTLE OPE:t EF-V29 (EF-V40) until the ficw rate as indicated by the differential pressure across CO-FE-7616 (7617) corresponds to the reference value.
The reference value is designated cn the Data Sheet.
Calculate flow rate frca the equation Q = 66.05
& where aP is the differential pressure across CO-FE-7616 (7617) in inches of water, and 0 is in gpm.
6.
.10 Cooling water ficw to ficor drain indicates that check valves EF-VIA(3) opened as required.
Record en Cata Sheet A(0) if valves EF-VlA(3) opened as required.
6.1.11 With pump EF-P-2A(3) operating as rcquired, verify that pumo EF-P-2S(A) is not windmilling due to fluid backficw through EF-il3(A).
Reccrd en Data Sheet S(A) that valves EF-VIS(A) cicsed as required.
6.1.12 With pump EF-?-2A or EF-P-28 operating as required, verify that pump EF-P-1 (steam driven EF pump) is not windmilling due to fluid backflow thrcugh EF-V2.
Record cn Data Sheet A that valve EF-V2 closed as required.
5.1.13 LET pump run five minutes or longer until system stabilizes.
NOTE:
Perform the folicwing two steps caly the first time this test in run during each calendar year, since bearing tem::erature measurement is only required once each year.
{
5.0 lb
23 B79 2303-M27A/B 7"
Revision 3 05/04/73 6.1.14 ALLOW EF-P-2A (23) to run until three successive bearing temperature measurements (as indicated by Ccmputer Group IS cr Ccmputer points 1653 and 1654 '(1653 and 1659))
t taken at 10 minute intervals, e.hange by less than 3%.
6.1.15 RECCRD on Cata Sheet A (3) the bearing temperatures, and times taken.
RECORD the final temperatures in the table.
6.1.16 RECORD the pump running inlet pressure frca C0-FI-2025 (2026).
RECORD the pump runn'r.g disenarge pressure frca EF-PI-6.1.17 2002 (2001).
6.1.18 CALCULATE and RECCRD ficw rate on Cata Sheet A (B) using the equation Q = 65.05 hP r.ere 9 is the D/P across CO-FE-7616 (7617) in inches of wawer, and Q is in gpm.
6.1.19 MEASURE and RECCRD the pump inbcard bearing vibration in the horizontal and vertical plane perpendicular to the rotating shaft.
INDICATE the higher of the two vibration amplitudes and designate whether in the horizenal (H) or vertical (V) plane.
INSURE the probe is on the designated test points.
6.1.20 STOP EF-P-2A (B).
6.1.21 REMOVE Eagle Eye Meter.
18) 197
~
6-
APR 23 g 2303-M27A/B Revision 4 08/30/73 6.1.22 Insure EF-V8A(B) is open, EF-V12A(B) is open, EF-V7A(B) is closed, and close EF-V39(EF-V40.
6.2 Emergency Feed Pump (EF-P2A(B)) Test.
6.2.1 INSTALL Eagle Eye Meter or equivalent at CO-FE-7616 (7617).
s 6.2.2 PERFORM Appendix A (B) Valve Line up.
6.2.3 RECORD cn Data Sheet A (B) the pump idle inlet pressure from CO-PI-2025 (2026).
6.2.4 INSURE Proper lube oil level on pump from bearing sight glasses and INITIAL Data Sheet.
6.2.5 START EF-P-2A (B) from Panel 6.2.6 INSURE EF-V27A (B) automatically cpens.
6.2.7 THROT7LE EF-V39 (EF-V40) until the fica rtte as indicated by the differential pressure across CO-FE-7616 (7617) corresponds to the reference value.
The reference value is designated on the Data Sheet.
Calculate flow rate from the equation Q = 66.05 hP where cP is the differential pressure across C0-FE-7616 (76i7) in inches of water, and 0 is in gpm.
7.0
h
"\\
D23 679 2303-M27A/B Revision 3 05/04/78 6.2.8 LET pump run five minutes or longer until system stabilizes.
NOTE:
Perform the following two steps only the first time this test in run during each calendar year, since bearing temperature measurement is only required once each year.
ALLOW EF-P-2A (23) to run until three successive bearing 5.2.9 temperat:.re measurements (as indicated by Computer Group 16, or C;mputer points 1653 and 1654 (1658 and 1659))
taken at 10 minute intervals, change by less than 3"..
RECCRD on Data Sheet A (B) the bearing temperatures, and 5.2.10 times taken.
RECCR0 the final temperatures in the table.
6.2.11 RECORD the pump running inlet pressure from CO-PI-2025 (2026).
RECCRD the pump running discharge pressure frca EF-PI-6.2.12 2C02 (2001).
CALCUL ATE and RECORD flow rate on Data Sheet A (B) from 6.2.13 the equation Q = 66.05 6P where aP is the differential pressure across CO-FE-7616 (7617) in inches of water, and Q is in gpm.
MEASURE and RECORD the pump ini: card bearing vibration in 5.2.14 the horizonal and vertical plane perpendicular to the rotating shaft.
INDICATE the higher of the two vibration amplitudes and designate whether in the horizcnal (H) or INSURE the pec'e is cn the designated c
vertical (V) plane.
test points.
I 6.2.15 STCP EF-P-2A (3).
181 199 3.0
@N I'O 2303-M27A/3
" A?R 2 3 GT3
,evision 4 n
CS/20/78 6.2.16 REMOVE Eagle Eye Meter.
6.2.17 Insure EF-VSA(B) is open, EF-V12A(B) is open, EF-V7A(S) is closed, and close EF-V39 (EF-V40).
7.0 ACCEPTANCE CRITERIA 7.1 If measured values fall within t'e Acceptable Range, Analysis portion of the data sheet shall be filled out and signed by the Shift Supervisor / Shift Foreman within 96 hours0.00111 days <br />0.0267 hours <br />1.587302e-4 weeks <br />3.6528e-5 months <br />.
7.2 If deviations fall within the Alert Range, the frequency of testing chall be doubled until the cause of the deviation is dete' mined and the condition corrected.
Analysis portion of the data sheet shall ta filled out and signed by the Lead Mechanical Engineer /ISI Cccedinatcr witnin 95 he;rs.
7.2 If deviations fall within the Required Action Range, the pump shall be declared incoerati'.'e and not returned to rervice until the cause
- ne deviaticn has been determined and the condition corrected.
C Analysis scrtion of the data sheet shall be filled out and signed by the Lead Mecnanical Engineer /ISI Coordinatcr.
.;3TE:
Correction can be replacement or repair or an analysis to demonstrate that the ccndition dees not ircair pump operability and that the pump will still fulfill its function. A new set of reference values shall be established after such analysis.
NOTE:
Modes I thru 3 - Two motor dris a emergency feedpumps CPERABLE per T.S. 3.7.1.2.
9.0
h
/
l 2303-M27A/S D23 Revision 3 93 05/04/78 NOTE:
If the acceptance criteria are not met, proceed with ACTION s tatement 3.7.1.2.
7.4 Each of the valves which has been tested to function, shall have been observed to function as required on the data sheet.
If a valve fails to exhibit the required change of valve stem or disc position during the test, corrective action shall be initiated irmediately. If the condition is not or tc net be corrected within 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />, the valve shall be declared inoperative.
When corrective action is required as a result of tests during cold shutdown, the condition shall be corrected before startup.
A retest shcwing acceptable operation shall be run following any required corrective action before the valve is returned to service.
7; When valve tes:ing has been performed, the Analysis portion of the data sheet shall be filled out by the Lead Mechanical Engineer /ISI Coordinator.
10.0
~
\\S\\
23\\
s
/hr
\\ %v j
FR 2 3 t379 2303-M27A/S Revision 4 DATA SHEET A 08/30/78 Motor Driven Emergency Fe d e pumo EF-P-2A Functional Test e
1 Pump idle inlet pressure 2.
Purp running inlet pressure (6 psig 3
Rumo running discharge press
.1.16 or 6.2.11) psig 4
Calculate differential press ure (6.1.17 or 6.2.12) psig 5.
ure (#3 - #2)
Lute oil level (Initial if s ti a
psig 5.
Puma Intcard Bearing Vibr ti s factory) a on (mils)
H Y
l
^ U "iT I TY M~ASURED l
ACCEPTAELE i ALERT PxiGE REQUIRED ACTION l LiL UE
, Pr;3E
.m.. -
ix,.
0L:-
1 i tcw jgigg rat:GE
. r. :.13 l gigg RErrREl;cE (PSIG)
LOy yAtug l'
I
}
>7.3 rt"? Rut,';I ;3 i liA l
i tlA
<7.
t t, :.,i. -,.
j 8
(?5:3) l l fiA enna.
150 i
1 I
>7.8 l
fiA n.7. 3 l'
flA PRESSURE I
1259 145 (PSI) f to 1223 1392 'I.
I 1392 to to 1259 1405
<l228 ! >l405 FLOW RATE
'1365 (3FM) 117.5 l
I I
to 112.5 127.5' PLMP Il,80ARD 127.5 to l to
{C:;)a"GTr"D 117.51 123.75!<ll2.Si pr l
n-
> l 28. 75li i25 i
I
~"
-130 i
FUW CUT 50Aa3 [
ffA liA fiA
>l80 BURI' (u-) ';G 7:"P'll 91.3 I
<180 t
MAX VIBRA TION
- tiA I
li l
- A
> tiA t
I (MILS)
I l
0.0 I
~>l30 i 109.3 t
to I
i
>) Oi i
l.0 to '
i i
NA
'v 1.5
- A easurements taken only during fi
>l.5 l
. 7 5.. y I
rst test run each calendar y j
ear 11.0
n
( 4 2303-M27A/B @ l L
APR 2 3 y; Revision 1 12/01/77 DATA SHEET A (Cent'd)
- =
Searing Temperatures NOTE:
To be reasured yearly.
TIME INBOARD BEARING TEMP.
OUTBOARD BEARING TEMP.
NOTE:
Three consecutive measurements taken at 10 minute intervals must change by less then 3%.
181 203 12.0
?SI d
2303-M27A/B j
AFR23 g Revision 3 DATA SHEET A (cont'd) l EAGLE EYE VIBRATI0ti I C0-PI-2025 EF-PI-2002 C0-FE-7616 METER INSTRUMENT MAliUFACTURE MODEL SERIAL N0.
f SCALE RANGE DATE:
TI?tE:
PERF0PftED BY:_
APPROVED SY:
DATE:
Valve No.
Stroke Time (sec)
Accectance Criteria EF-V27A CPEN in
<3 sec.
Valve No.
Valve Function Recuirement Da te/ Ini ti a' EF-V1 A (check valve) OPE: 4 EF-V13 (check valve) CLOSED EF-72 (check valve) CLCSED PEPFORMED E!-
DATE:
APPROVED SY:
DATE:
Af,ALYSIS:
Analysis by:
DATE:
TIME.
Analysis ;;erfor ed within 95 hours0.0011 days <br />0.0264 hours <br />1.570767e-4 weeks <br />3.61475e-5 months <br />?
Yes No 181 204
~
13.0
/
['
2303-M27A/B jb APR 2 3 7379 Revision 4 03/30/78 OATA SHEET S Motor Driven Emergency Feedpump EF-P-2B Functional Test psig 1.
Pump idle inlet pressure 2.
Pumo running inlet pressure (6.1.16 or 6.2.11)
Psi 9 Pump running discharge pressure (6.1.17 or 6.2.12) psig 3.
4 Calculate differential pressure (#3 - #2) psig 5.
Lute oil level (Initial if satisfactory) 5.
Pump Inboard Bearing Vibration (nils)
H V
REQUIRED ACTION MEASURED ACCE?!AELE ALERT RANGE PANGE REFERENCE QUANTilf VALUE RANGE LOW HIGH LOW HIGH VALUE i
PU"P ICLE INLET PRESS.
$.8 NA l48 7
g (PSIG)
>7.8 NA j NA I
I PU"P RUNNING INLET PRESS.
(PSIG)
>7.8 NA NA 5.7. 8 NA 144 PUMP DIFF.
1279 1238 l 1403 1376 l>l417 PRESSURE to to to
<l238 (PSI) 1403 1279 1417 FLCW RATE li7.5 1i2.5 127.Q t
1
>128.75 125.3 (GPM) to to l to I <112.5 i
127.5 117.5 128.75 i
PLMP IN50ARD 3 EARING TEMP.
<l80 NA NA NA 2180 lla
("F)
PUMPOUIS0ARDl*
BEARING TEMP.
<180 NA NA NA 2.180 96.6
("F)
MAX VIERATION O to 1 NA
>i tc NA l>l.5
. 3 2 '/
1.5 (MILS)
H'easurements taken only curing first test run each calendar year _
181 205
^
l ~,. 0
=
/ (, l 2303-M27A/B k 2 3 E73 Revision 1 12/01/77 t
DATA SHEET B (Cont'd)
Bearing Temperatures NOTE:
To be measured yearly.
TIME INBOARD BEARING TEMP.
CUTE 0ARD BEARING TEMP.
':~E:
Three consecutive measurements taken at 10 minute intervals must change by less then 3%.
15.0 181 206
.;\\
V 2303-M27A/B APR 2 3 D73 Revision 3 g i}
_CATA SHEET S (Cont'd)
C5/04/73 l
l EAGLE EYE VIBRA TIOT-CO-PI-2026 EF-PI-2001 l CO-FE-7617 l METER INSTRUMENT MANUFACTURE i
M00EL SERIAL NO.
SCALE RANGE PERFCRMED BY:
DATE:
TIME:
APPROVED BY:
CATE:
!' a l v e No.
Stroke Time (sec.)
Accectance Criteria EF-V273 CPEN in 2 3 sec.
Valve ':.
Valve Functinn Pecuirement Date/ Initial EF-V1 3 (check valve) CPEN EF-VlA (check valve) CLOSED PERFCRMED 3 f:
DATE:
APPROVED BY:
CATE:
ANALYSIS:
Analysis by:
CATE:
TIME:
Analysis performed within 95 hours0.0011 days <br />0.0264 hours <br />1.570767e-4 weeks <br />3.61475e-5 months <br />?
Yes No 15.0 181 207
Fs' V
I I
s Q
2303-M27A/B
EF-V7A EF-P-2A Recirc to Cond.
OP EF-VEA EF-P-2A Recire. to CO-T-1A CL EF-V9 CO-T-1A isolation valve OP CO-V92A EF Suction frca CO-T-1A CP CC-7953 EF Suction Frcm CO-T-1B CP CC-V37 EF Pumps Suct Hdr Block CP EF-VilA Emerg. F.W. to RC-H-1A CL EF-V12A Energ. F W. to RC-H-1A CL EF-732A EF-VilA Bypass CL EF-V33A EF-V12A Bypass CL EF-V29A EF-P-2A Cooling Water Inlet CP EF-131A Searing ccoling water outlet CP EF-VilB Emerg. F.W. to RC-H-18 CL EF-V125 Emerg. F.W. to RC-H-13 CL EF-V328 EF-VilB Bypass CL EF '!333 EF-V123 Bypass CL
!81 208 17.0
n L
2303-P27A/B APR 2 3 Ep9 Revision 4 08/30/78 APPENDIX B Motor Driven Emergency Feedpump, EF-P-23 Recirculation Valve Line-Up Valve Description Position Initial C0-V85 Iso Valve on Header' from Cond. r umps OP CD-V823 Iso Valve frcm Cond. Storate Tanks OP CO-V833 Suction to EF-P-28 L.O.
EF-V73 EF-P-23 Recirc to Cand.
CP EF-VES EF-P-23 9ecirc. to CO-T-1A CL EF-V9 CD-T-13 isolation valve CP CO-V9EA EF Suction frcm CD-T-1 A CP
'v 7-3
_ Suct en Frcm CO-7_]3 tr 0?
CC '/37 EF Pumos Suct Hdr Sicck CP EF-VilA Emerg. r.W. to RC-H-1A CL EF-V12A Energ. F.W. to RC-H-1A CL EF-V32A EF-VilA 33 ass CL EF-V33A EF-V12A Bypass CL EF-V293 EF-P-23 Cooling Water Inlet CP EF-V313 Cocling viater cutlet OP EF-Vll3 Emerg. F.W. to RC-H-13 CL EF-V123 Emerg. F.W. to RC-H-13 CL EF-V323 EF-Vil3 Bypass CL EF-V333 EF-V123 Bypass CL 181 209 13.0