ML062060311

Inservice Inspection Reports for End of Cycle 14 Refueling Outage

ML062060311
Person / Time
Site:	Catawba
Issue date:	07/18/2006
From:	Jamil D Duke Energy Carolinas, Duke Power Co
To:	Document Control Desk, Office of Nuclear Reactor Regulation
References
Download: ML062060311 (273)

Text

D.M. JAMIL Duke

,Energy& Vice President Catawba Nuclear Station 4800 Concord Rd. / CN01 VP York, SC 29745-9635 803 831 4251 803 831 3221 fax July 18, 2006 U.S. Nuclear Regulatory Commission Attention: Document Control Desk Washington, D.C. 20555

Subject:

Duke Power Company LLC d/b/a Duke Energy Carolinas, LLC Catawba Nuclear Station, Unit 2 Docket Number 50-414 Inservice Inspection Reports for End of Cycle 14 Refueling Outage Please find attached the subject reports which provide the results of the inservice inspection effort associated with the subject outage. Note that two reports are being submitted via this letter due to Unit 2's running of concurrent intervals during a portion of the outage cycle. One covers the seventh (last) outage cycle in the third period of the second inservice inspection interval, and one covers the first outage cycle in the first period of the third inservice inspection interval.

There are no regulatory commitments contained in this letter or its attachments.

If you have any questions concerning this material, please call L.J. Rudy at (803) 831-3084.

Very truly yours, D.M. Jamil LJR/s Attachments A091 www. duke-energy. corn

Document Control Desk Page 2 July 18, 2006 xc (with attachments):

W.D. Travers, Regional Administrator U.S. Nuclear Regulatory Commission, Region II Atlanta Federal Center 61 Forsyth St., SW, Suite 23T85 Atlanta, GA 30303 E.F. Guthrie, Senior Resident Inspector U.S. Nuclear Regulatory Commission Catawba Nuclear Station J.F. Stang, Jr., Senior Project Manager (addressee only)

U.S. Nuclear Regulatory Commission Mail Stop 8 H4A Washington, D.C. 20555-0001

Attachment 1 Inservice Inspection Report Catawba Unit 2 2006 Refueling Outage EOC14 (Outage 7)

Second Inservice Inspection Interval

FORM NIS-1 OWNER'S REPORT FOR INSERVICE INSPECTIONS As required by the Provisions of the ASME Code Rules

1. Owner: Duke Energy, 526 S. Church St., Charlotte, NC 28201-1006 (Name and Address of Owner)

2. Plant: Catawba Nuclear Station, 4800 Concord Road. York, SC 29745 (Name and Address of Plant)

3. Plant Unit: 2 4. Owner Certificate of Authorization (if required): N/A

5. Commercial Service Date: 8/19/86 6. National Board Number for Unit: 173

7. Components Inspected:

Component or Manufacturer Manufacturer State or National Appurtenance Installer Installer Serial Province No. Board No.

No.

See Section 1.1 in the Attached Report Note: Supplemental sheets in the form of lists, sketches, or drawings may be used provided (1) size is 81/2 in.

x 11 in., (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

Total number of pages contained in this report 83

FORM NIS-1 (Back)

8. Examination Dates: October 24, 2004 to April 24, 2006

9. Inspection Period Identification: Third Period

10. Inspection Interval Identification: Second Interval

11. Applicable Edition of Section XI: 1989 Addenda None

12. Date / Revision of Inspection Plan: September 9, 1999 / Revision 2

13. Abstract of Examinations and Tests. Include a list of examinations and tests and a statement concerning status of work required for the Inspection Plan: See Sections 2.0, 3.0 and 6.0

14. Abstract of Results of Examinations and Tests: See Section 4.0 and 6.0

15. Abstract of Corrective Measures: See Subsection 4.3 We certify that a) the statements made in this report are correct, b) the examinations and tests meet the Inspection Plan as required by the ASME Code, Section Xl, and c) corrective measures taken conform to the rules of the ASME Code,Section XI.

Certificate of Authorization No. (if applicable) N/A Expiration Date N/A Date --, o'L I* jOD ,Signed Duke Energy By Owner CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of N6C employed by

• HSB of Connecticut have inspected the components described in this Owner's Report during the period ji--O-iQAi*., to J IA - 06 _, and state that to the best of my knowledge and belief, the Owner has performed examinations and tests and taken corrective measures described in this Owner's Report in accordance with the Inspection Plan and as required by the ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations, tests, and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection Commissions A)J CY-7* R N-Jnspeco*rs Signature National Board, State, Province, and Endorsements Date - 1_- 0 (p _)

• The Hartford Steam Boiler Inspection & Insurance Company of Connecticut 200 Ashford Center North Suite 205 Atlanta, GA. 30338-4860 (800) 417-3721 www.hsbct.com

INSERVICE INSPECTION REPORT CA TA WBA - UNIT 2 2006 REFUELING OUTAGE EOC14 (OUTAGE 7)

Location: 4800 Concord Road, York, South Carolina 29745 NRC Docket No. 50-414 National Board No. 173 Commercial Service Date: August 19, 1986 Owner: Duke Energy 526 South Church St.

Charlotte, N.C. 28201-1006 Revision 0 Prepared By: Date Reviewed By: Date 7,4a Approved By: -k'001ý Date 4L44~

DISTRIBUTION LIST

1. Duke Energy Quality Assurance Technical Services (QATS)(Original) 2 NRC Document Control Desk

TABLE OF CONTENTS Section Title Revision 1.0 General Information 0 2.0 Second Ten-Year Interval Inspection Status 0 3.0 Final Inservice Inspection Plan 0 4.0 Results of Inspections Performed 0 5.0 Owner's Report for Repair / Replacement Activities 0 6.0 Pressure Testing 0

"-/ 1.0 General Information This report describes the Inservice Inspection of Duke Energy's Catawba Nuclear Station Unit 2 during Outage 7 / EOC14. This is the Second Outage of the Third Inspection Period of the Second Ten-Year Interval. ASME Section Xl, 1989 Edition with no Addenda, was the governing Code for selection and performance of the ISI examinations.

Included in this report are the inspection status for each examination category, the final inservice inspection plan, the inspection results for each item examined, and corrective actions taken when reportable conditions were found. In addition, there is an Owner's Report for Repair/ Replacement Section included for completed NIS-2 documentation of repairs and replacements.

1.1 Identification Numbers Manufacturer Manufacturer State or National Item or Installer or Installer Province No. Board Serial No. No.

Reactor Vessel Combustion 8871 N/A 21667 Engineering Pressurizer Westinghouse 1931 N/A W26949 Steam Generator 2A Westinghouse 1923 N/A 4 Steam Generator 2B Westinghouse 1922 N/A 3 Steam Generator 2C Westinghouse 1921 N/A 2 Steam Generator 20 Westinghouse 1924 N/A 5 Reactor Coolant Pump 2A Ionics, Inc. 1S-86P765 N/A 342 Reactor Coolant Pump 2B Ionics, Inc. 2S-86P765 N/A 343 EOC 14 Refueling Outage Report Page 1 of 6 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

1.1 Identification Numbers (Continued)

Manufacturer Manufacturer State or National Item or Installer or Installer Province Board No.

Serial No. No.

Reactor Coolant Pump 2C Ionics, Inc. 3S-86P765 N/A 586 Reactor Coolant Pump 2D Ionics, Inc. 4S-86P765 N/A 587 Reactor Coolant System Duke Power Co. C-2NC N/A 171 Safety Injection System Duke Power Co. C-2NI N/A 172 Residual Heat Removal Duke Power Co. C-2ND N/A 154 System Chemical and Volume Duke Power Co. C-2NV N/A 170 Control System Auxiliary Feedwater Duke Power Co. C-2CA N/A 159 System Feedwater System Duke Power Co. C-2CF N/A 158 Refueling Water System Duke Power Co. C-2FW N/A 141 Main Steam Supply to Duke Power Co. C-2SA N/A 134 Auxiliary Equipment Main Steam System Duke Power Co. C-2SM N/A 162 Main Steam Vent to Duke Power Co. C-2SV N/A 156 Atmosphere System Containment Spray System Duke Power Co. C-2NS N/A 150 Steam Generator Duke Power Co. C-2BB N/A 155 Blowdown System Steam Generator Wet Duke Power Co. C-2BW N/A 152 Layup Recirculation System EOC 14 Refueling Outage Report Page 2 of 6 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

1.1 Identification Numbers (Continued)

Manufacturer Manufacturer State or National Item or Installer or Installer Province No. Board No.

Serial No.

Spent Fuel Cooling Duke Power Co. C-2KF N/A 151 System Boron Recycle System Duke Power Co. C-2NB N/A 153 Nuclear Sampling Duke Power Co. C-2NM N/A 169 System Containment Duke Power Co. C-2NW N/A 165 Penetration Valve Injection Water System Liquid Radwaste Duke Power Co. C-2WL N/A 168 System Excess Letdown Heat Atlas Industrial 3205 N/A 2583 Exchanger Manufacturing Company Seal Water Heat Atlas Industrial 3621 N/A 2977 Exchanger Manufacturing Company Vertical Letdown Heat Joseph Oat 2268-2B N/A 944 Exchanger Corporation Regenerative Heat Joseph Oat 2255-1 C3 N/A 877 Exchanger Corporation Residual Heat Joseph Oat 2A 2267-3C N/A 848 Removal Heat Corporation Exchanger 2B 2267-3D N/A 849 Containment Spray Joseph Oat 2A 2636-B N/A 3449 Heat Exchanger Corporation 2B 2636-C N/A 3456 Seal Water Injection Pall Trinity Micro 2A 35367 N/A 19025 Filter Corporation 2B 35366 N/A 19024 Volume Control Tank Lamco Industries 2286.30 N/A 77171 1 Inc.

EOC 14 Refueling Outage Report Page 3 of 6 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

1.1 Identification Numbers (Continued)

Manufacturer Manufacturer State or National Item or Installer or Installer Province No. Board Serial No. No.

Residual Heat Removal Ingersoll-Rand 2A 077647 N/A 237 Pump 2B 077648 N/A 238 Containment Spray Pump Bingham- 2A 230342 N/A 215 Willamette 2B 230343 N/A 216 Safety Injection Pump Pacific Pumps 2A 49361 N/A 240 2B 49362 N/A 241 Centrifugal Charging Pump Pacific Pumps 2A 49780 N/A 262 2B 49779 N/A 259 1.2 Personnel, Equipment and Material Certifications All personnel who performed or evaluated the results of inservice inspections during the time frame bracketed by the examination dates shown on the NIS-1 Form were certified in accordance with the requirements of the 1989 Edition of ASME Section XI with no addenda including Appendix VII for ultrasonic inspections. In addition, ultrasonic examiners were qualified in accordance with ASME Section XI, Appendix VIII,1995 Edition with the 1996 Addenda through the Performance Demonstration Initiative (PDI) for welds and components within the scope of Appendix VIII.

The appropriate certification records for each inspector, calibration records for inspection equipment, and records of materials used (i.e. NDE consumables) are on file at Catawba Nuclear Station or copies may be obtained by contacting the Duke Energy Corporate Office in Charlotte, North Carolina.

The copies of the certification records for Washington Group and Atlantic Group inspectors can be obtained by contacting the Duke Energy Corporate Office in Charlotte, North Carolina.

EOC 14 Refueling Outage Report Page 4 of 6 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

1.3 Reference Documents The following reference documents apply to the inservice inspections performed during this report period. A copy may be obtained by contacting the ISI Plan Manager at Duke Energy's Corporate Office in Charlotte, North Carolina.

Duke Energy Corporation, Catawba Nuclear Station, Units 1 and 2 Docket Numbers 50-413 and 50-414, Request for Relief Number 03-001, Relief from Volumetric Examination Requirements on Regenerative Heat Exchangers.

Duke Energy Corporation Catawba Nuclear Station, Unit 2 Docket Number 50-414, Request for Relief Serial Number (To Be Filed Later) Limited Weld Coverage During End-of-Cycle 14 Refueling Outage).

1.4 Augmented and Elective Examinations Augmented and Elective Examination information found within this Inservice Inspection Owner's Summary Report is not required by the ASME Section XI Code; therefore, it is exempt from ANII review, verification, and/or record certification.

EOC 14 Refueling Outage Report Page 5 of 6 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

1.5 Responsible Inspection Agency The Hartford Steam Boiler Inspection and Insurance Company of Connecticut is responsible for the third party inspections required by ASME Section XI.

Authorized Nuclear Inservice Inspector(s)

Name: R. N. McGill Employer: The Hartford Steam Boiler Inspection & Insurance Company of Connecticut Business 200 Ashford Center North Address: Suite 205 Atlanta, GA 30338-4860 (800) 417-3721 www.hsbct.com EOC 14 Refueling Outage Report Page 6 of 6 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

2.0 Second Ten-Year Interval Inspection Status The completion status of inspections required by the 1989 ASME Code Section Xl, no addenda, is summarized in this section. The requirements are listed by the ASME Section XI Examination Category as defined in Table IWB-2500-1 for Class 1 Inspections, Table IWC-2500-1 for Class 2 Inspections, and IWF-2500-1 (Code Case N-491 applies) for Class 1, 2 and 3 Component Supports. Augmented / Elective Inspections are also included.

Class 1 Inspections Examination Description Inspections Inspections Percentage 1Deferral Category Required Completed Completed Allowed B-A Pressure Retaining Welds 24 24 100% Yes in Reactor Vessel B-B Pressure Retaining Welds 5 5 100% No in Vessels Other than Reactor Vessels B-D Full Penetration Welds of 36 36 100% Partial Nozzles in Vessels Inspection Program B B-E Pressure Retaining Partial REFERENCE SECTION 6.0 OF THIS REPORT Penetration Welds in Vessels B-F Pressure Retaining 46 46 100% No Dissimilar Metal Welds B-G-1 Pressure Retaining Bolting 220 220 100% Yes Greater than 2" in Diameter B-G-2 Pressure Retaining Bolting 27 27 100% No 2" and Less in Diameter B-H Integral Attachments for 5 5 100% No Vessels B-J Pressure Retaining Welds 224 224 100% No in Piping EOC 14 Refueling Outage Report Page 1 of 4 Catawba Unit 2 Revision 0 Section 2 June 20, 2006

Class 1 Inspections (Continued) t Deferral Examination Description Inspections Inspections Percentage Category Required Completed Completed Allowed B-K-1 Integral Attachments for N/A N/A N/A N/A Piping, Pumps and Valves B-L-1 Pressure Retaining Welds N/A N/A N/A N/A in Pump Casings B-L-2 Pump Casings 1 0 N/A Yes See Note 2 below B-M-1 Pressure Retaining 1 1 100% Yes Welds in Valve Bodies B-M-2 Valve Body > 4 in. 7 7 100% Yes Nominal Pipe Size B-N-1 Interior of Reactor Vessel 3 3 100% No B-N-2 Integrally Welded Core Support Structures and 2 2 100% Yes Interior Attachments to Reactor Vessels B-N-3 Removable Core Support 1 1 100% Yes Structures B-O Pressure Retaining Welds 3 3 100% Yes in Control Rod Housings B-P All Pressure Retaining REFERENCE SECTION 6.0 OF THIS REPORT Components B-Q Steam Generator Tubing See Note 3 below F-A Class 1 Component 71 71 100% No Supports (Code Case N-491)

Notes:

1. Deferral of Inspection to the end of the Interval as allowed by ASME Section XI Table IWB 2500-1. These examination categories are exempt from percentage requirements per IWB-2412 (a), Inspection Program B.

2. Examination required only if pump casing is disassembled. The pump casing was not disassembled during the Second Ten year Inspection Interval.

3. Steam Generator Tubing is examined and documented by Nuclear Technical Services as required by the Station Technical Specifications and Is not Included In this report.

EOC 14 Refueling Outage Report Page 2 of 4 Catawba Unit 2 Revision 0 Section 2 June 20, 2006

Class 2 Inspections Examination Description Inspections Inspections Percentage Category Required Completed Completed C-A Pressure Retaining Welds 31 19 61.29%

in Pressure Vessels See Note Below C-B Pressure Retaining Nozzle 11 11 100%

Welds in Vessels C-C Integral Attachments for 68 68 100%

Vessels, Piping, Pumps, and Valves C-D Pressure Retaining Bolting N/A N/A N/A Greater Than 2" in Diameter C-F-1 Pressure Retaining Welds 290 290 100%

in Austenitic Stainless Steel or High Alloy Piping C-F-2 Pressure Retaining Welds 46 46 100%

in Carbon or Low Alloy Steel Piping C-G Pressure Retaining Welds 20 20 100%

in Pumps and Valves I I C-H All Pressure Retaining REFERENCE SECTION 6.0 OF THIS Components REPORT F-A Class 2 Component 230 230 100%

Supports (Code Case N-491)

Note:

Twelve (12) Regenerative Heat Exchanger Welds (Shell-to-Head Welds and Tubesheet-to-Shell Welds),

originally scheduled for EOC13, were not performed because of high radiation conditions.

(Request for Relief Serial No.03-001, referenced In Section 1.3 of this report, was submitted and approved to omit their Inspection during the Interval (See SER dated February 17, 2005).

EOC 14 Refueling Outage Report Page 3 of 4 Catawba Unit 2 Revision 0 Section 2 June 20, 2006

Augmented / Elective Inspections Description PercentageComplete NI Cold Leg Accumulator Welds Subject to Unanalyzed 100% of requirements for Outage 7 / EOC-14 Thermal Transients EOC 14 Refueling Outage Report Page 4 of 4 Catawba Unit 2 Revision 0 Section 2 June 20, 2006

3.0 Final Inservice Inspection Plan The final Inservice Inspection Plan shown in this section lists all ASME Section XI Class 1, Class 2, and Augmented / Elective Inspections credited for this report period.

The information shown below is a field description for the reporting format included in this section of the report:

ITEM NUMBER = ASME Section XI Tables IWB-2500-1 (Class 1), IWC-2500-1 (Class 2), IWF-2500-1 (Class 1 and Class 2 ), Augmented / Elective Requirements ID NUMBER = Unique Identification Number SYS = Component System Identification ISO / DWG NUMBERS = Location and / or Detail Drawings PROC = Examination Procedures INSP REQ = Examination Technique - Magnetic Particle, Dye Penetrant, etc.

MAT/ SCH = General Description of Material DIA / THICK = Diameter / Thickness CAL BLOCKS = Calibration Block Number COMMENTS = General and / or Detail Description EOC 14 Refueling Outage Report Page 1 of 1 Catawba Unit 2 Revision 0 Section 3 June 20,2006

EOC 14 DUKE ENERG( .;ORPORATION CATEGORY B-F, Pressure Retaining Dissimilar INSERVICE INSPECTION PLAN MANAGEMENT C Metal Welds Inservice Inspection Database Management System Plan Report Resctor Vessel Catawba 2 Page 1 Inservice Inspection Plan for Interval 2 Outag e7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAhL BLOCKS COMMENTS

• • • • NPS 4 or larger; Nozzle-to-Safe End Butt Welds ****

B05.010.001B 2RPV-201-121BSE CNM 2201.01-67 NDE-35 PT SS-CS 27.500 RV Inlet Nozzle To Safe End 67 Degrees Loop B Circumferential NC E 8871-171-009 2.500 (Reactor Building 113 Degrees). To Be Done With Class A Term end CNM 2201.01-74/5 Nozzle to B05.130.004B.

Dissimilar Safe End B05.010.002B 2RPV-201-121ASE CNM 2201.01-67 NDE-35 PT SS-CS 27.500 RV Inlet Nozzle To Safe End 113 Degrees Loop A Circumferential NC E 8871-171-009 2.500 (Reactor Building 67 Degrees). To Be Done With Class A Term end CNM 2201.01-74/5 Nozzle to B05.130.008B.

Dissimilar Safe End B05.010.003B 2RPV-201-121DSE CNM 2201.01-67 NDE-35 PT SS-CS 27.500 RV Inlet Nozzle To Safe End 247 Degrees Loop D Circumferential NC E 8871-171-009 2.500 (Reactor Building 293 Degrees). To Be Done With Class A Term end CNM 2201.01-74/5 Nozzle to B05.130.012B.

Dissimilar Safe End B05.010.004B 2RPV-201-121CSE CNM 2201.01-67 NDE-35 PT SS-CS 27.500 RV Inlet Nozzle To Safe End 293 Degrees Loop C Circumferential NC E 8871-171-009 2.500 (Reactor Building 247 Degrees). To Be Done With Class A Term end CNM 2201.01-74/5 Nozzle to B05.130.016B.

Dissimilar Safe End Total B05.010 Items: 4

DUKE ENERGK ;ORPORATION C CATEGORY B-F, Pressure Retaining Dissimilar INSERVICE INSPECTION PLAN MANAGEMENT Metal Welds Inservice Inspection Database Management System Plan Report Catawba 2 Page 2 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• • • • NPS 4 or Larger; Dissimilar Metal Butt Welds

• B05.130.004B 2NC1 1-08 CN-2NC-01 1' NDE-35 PT SS-CS 27.500 Inlet Nozzle 67 Degrees Loop B (Reactor Building Circumferential NC CN-2553-1.0 2.500 113 Degrees). To be done with B05.010.001B.

Class A Safe End to Dissimilar Pipe B05.130.008B 2NC9-08 CN-2NC-009 NDE-35 PT SS-CS 27.500 Inlet Nozzle 113 Degrees Loop A (Reactor Building Circumferential NC CN-2553-1.0 2.500 67 Degrees). To be done with B05.010.002B.

Class A Safe End to Dissimilar Pipe B05.130.012B 2NC15-08 CN-2NC-015 NDE-35 PT SS-CS 27.500 Inlet Nozzle 247 Degrees Loop D (Reactor Building Circumferential NC CN-2553-1.0 2.500 293 Degrees). To be done with B05.010.003B.

Class A Safe End to Dissimilar Pipe B05.130.016B 2NC13-08 CN-2NC-013 NDE-35 PT SS-CS 27.500 Inlet Nozzle 293 Degrees Loop C (Reactor Building Circumferential NC CN-2553-1.0 2.500 247 Degrees) To be done with B05.010.004B.

Class A Safe End to Dissimilar Pipe Total B05.130 Items: 4 Total B05 Items: 8

EOC 14 C DUKE ENERG;ORPORATION (-

CATEGORY B-J. Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Piping Inservice Inspection Database Management System Plan Report NPS 4 or Larer Catawba 2 Page 3 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAJTHK CAL BLOCKS COMMENTS

• • • • Circumferential Welds ****

B09.01 1.006 2NC1 19-4 CN-2NC-1 19 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10 Circumferential NC CN-2553-11.1 160 0.719 50211 Depending on the examiners qualifications, Class A 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

B09.011.006A 2NC1 19-4 CN-2NC-1 19 NDE-35 PT SS 6.000 Circumferential NC CN-2553-11.1 160 0.719 Class A 90 Degree Elbow to Pipe B09.011.007 2NC48-5 CN-2NC-48 NDE-600 UT SS 10.000 *Reference General Requirements Section 8.1.10.

Circumferential NC CN-2553-1.0 140 1.000 Depending on the examiner's qualifications, Class A 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

B09.011.007A 2NC48-5 CN-2NC-48 NDE-35 PT SS 10.000 Circumferential NC CN-2553-1.0 140 1.000 Class A 90 Degree Elbow to Pipe B09.011.020 2NC255-1 CN-2NC-255 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10 Circumferential NC CN-2553-1.0 0.864 50211 Depending on the examiners qualifications, Class A UHI Adapter to Procedure PDI-UT-2 may be used in lieu of Pipe Cap NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

B09.011.020A 2NC255-1 CN-2NC-255 NDE-35 PT SS 6.000 Circumferential NC CN-2553-11.0 0.864 Class A UHI Adapter to Pipe Cap B09.011.021 2NC255-3 CN-2NC-255 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10 Circumferential NC CN-2553-11.0 0.864 50211 Depending on the examiners qualifications, Class A UHI Adapter to Procedure PDI-UT-2 may be used in lieu of Pipe Cap NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 C DUKE ENERGQCORPORATION (

CATEGORY B-J, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report EMN 4 oBRLarger Catawba 2 Page 4 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DINTHK CAL BLOCKS COMMENTS B09.011.021 A 2NC255-3 CN-2NC-255 NDE-35 PT SS 6.000 Circumferential NC CN-2553-1.0 0.864 Class A UHI Adapter to Pipe Cap B09.011.022 2NC255-4 CN-2NC-255 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10 Circumferential NC CN-2553-1.0 0.864 50211 Depending on the examiners qualifications, Class A UHI Adapter to Procedure PDI-UT-2 may be used in lieu of Pipe Cap NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

B09.011.022A 2NC255-4 CN-2NC-255 NDE-35 PT SS 6.000 Circumferential NC CN-2553-1.0 0.864 Class A UHI Adapter to Pipe Cap B09.011.023 2NC257-1 CN-2NC-257 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10 Circumferential NC CN-2553-1.0 0.864 50211 Depending on the examiners qualifications, Class A Pipe to Procedure PDI-UT-2 may be used in lieu of Reducer NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

B09.011.023A 2NC257-1 CN-2NC-257 NDE-35 PT SS 6.000 Circumferential NC CN-2553-1.0 0.864 Class A Pipe to Reducer B09.011.067 2NI379-5 CN-2NI-379 NDE-600 UT SS 8.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.2 160 0.906 Depending on the examiners qualifications, Class A Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

B09.011.067A 2NI379-5 CN-2NI-379 NDE-35 PT SS 8.000 Circumferential NI CN-2562-1.2 160 0.906 Class A Pipe to 90 Degree Elbow B09.011.068 2NI379-8 CN-2NI-379 NDE-600 UT SS 8.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.2 160 0.906 Depending on the examiners qualifications, Class A 90 Degree Elbow to Procedure PDI-UT-2 may be used In lieu of Pipe NDE-600. If PDIoUT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 C DUKE ENER ,;ORPORATION (.

CATEGORY B-J, Pressure Retainin q Welds In INSERVICE INSPECTION PLAN MANAGEMENT Piping InservIce Inspection Database Management System Plan Report Catawba 2 Page 5 r+/- 4r Larger Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS B09.011.068A 2NI379-8 CN-2NI-379 NDE-35 PT SS 8.000 Circumferential NI CN-2562-1.2 160 0.906 Class A 90 Degree Elbow to Pipe B09.011.069 2NI396-2 CN-2NI-396 NDE-600 UT SS 4.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.2 160 0.531 Depending on the examiners qualifications, Class A 6X4 Reducer to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

B09.011.069A 2NI396-2 CN-2NI-396 NDE-35 PT SS 4.000 Circumferential NI CN-2562-1.2 160 0.531 Class A 6X4 Reducer to Pipe B09.011.070 2NI396-4 CN-2NI-396 NDE-600 UT SS 4.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.2 160 0.531 Depending on the examiners qualifications, Class A Pipe to Procedure PDI-UT-2 may be used in lieu of 4X2 Reducer NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

B09.011.070A 2NI396-4 CN-2NI-396 NDE-35 PT SS 4.000 Circumferential NI CN-2562-1.2 160 0.531 Class A Pipe to 4X2 Reducer B09.011.099 2NC112-4 CN-2NC-112 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10 Circumferential NC CN-2553-1.1 160 0.719 50211 Depending on the examiners qualifications, Class A Pipe to Procedure PDI-UT-2 may be used in lieu of 45 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

B09.011.099A 2NC 112-4 CN-2NC-1 12 NDE-35 PT SS 6.000 Circumferential NC CN-2553-1.1 160 0.719 Class A Pipe to 45 Degree Elbow Total B09.011 items: 22

EOC 14 C DUKE ENERG(,CORPORATION (

CATEGORY B-J, Pressure Retaininq Welds In IN! SERVICE INSPECTION PLAN MANAGEMENT PIping Inser vice Inspection Database Management System Plan Report ess Than NPS 4 Catawba 2 Page 6 N Ins ;ervice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIANHK CAL BLOCKS COMMENTS

• • • • Circumferential Welds ****

B09.021.007 2NC140-4 CN-2NC-140 NDE-35 PT SS 1.500 Circumferential NC CN-2553-1.0 160 0.281 Class A Pipe to Pipe B09.021.008 2NC140-5 CN-2NC-140 NDE-35 PT SS 1.500 Circumferential NC CN-2553-1.0 160 0.281 Class A Pipe to Cold Leg Nozzle 2D B09.021.009 2NC145-5 CN-2NC-145 NDE-35 PT SS 1.500 Circumferential NC CN-2553-1.0 160 0.281 Class A Pipe to Pipe B09.021.010 2NC146-6 CN-2NC-146 NDE-35 PT SS 1.500 Circumferential NC CN-2553-1.0 160 0.281 Class A Pipe to Cold Leg Nozzle 2C B09.021.027 2NC74-16 CN-2NC-74 NDE-35 PT SS 2.000 Circumferential NC CN-2553-1.0 160 0.344 Class A Pipe to Pipe Total B09.021 Items: 5

EOC 14

( DUKE ENERGJ.LORPORATION (

CATEGORY B-J, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT P112inc Inservice Inspection Database Management System Plan Report WBranch Pipe Connection Welds Catawba 2 Page 7 Inservlce Inspection Plan for Interval 2 Outage 7 0612012006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUIMBERS PROC INSP REQ MAT/SCH DINTHK CAL BLOCKS COMMENTS

• • • • NPS 4 or Larger ****

B09.031.001 2NC11-WN7 CN-2NC-11 NDE-830 UT SS 14.000 50386 CNM 2201.01-104/4 Branch NC CN-2553-1.0 160 2.300 Nozzle B tp P1 Class A Nozzle to Cast Stainless Steel Base Material Pipe Reference RFR 04-CN-001 Rev. 1 B09.031.002 2NC11-WN8 CN-2NC-1 1 NDE-830 UT SS 12.000 50386 CNM 2201.01-104/4 Branch NC CN-2553-1.0 140 2.300 Nozzle C to P1 Class A Nozzle to Cast Stainless Steel Base Material Pipe Reference RFR 04-CN-001 Rev. 1 Total B09.031 Items: 2

EOC 14

( DUKE ENERG(,,;ORPORATION (

CATEGORY B-J, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Mocket Welds Catawba 2 Page 8 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DINTHK CAL BLOCKS COMMENTS B09.040.007 2NC53-36 CN-2NC-53 NDE-35 PT SS 2.000 Socket NC CN-2553-1.0 160 0.344 Class A Tee to Pipe B09.040.008 2NC53-37 CN-2NC-53 NDE-35 PT SS 2.000 Socket NC CN-2553-1.0 160 0.344 Class A Pipe to Tee B09.040.013 2NC89-20 CN-2NC-89 NDE-35 PT SS 2.000 Socket NC CN-2553-1.0 160 0.344 Class A Pipe to VLV 2NC004 B09.040.014 2NC89-21 CN-2NC-89 NDE-35 PT SS 2.000 Socket NC CN-2553-1.0 160 0.344 Class A VLV 2NC004 to Pipe B09.040.01 5 2NC89-4 CN-2NC-89 NDE-35 PT SS 2.000 Socket NC CN-2553-1.0 160 0.344 Class A Pipe to 90 Degree Elbow B09.040.016 2NC89-7 CN-2NC-89 NDE-35 PT SS 2.000 Socket NC CN-2553-1.0 160 0.344 Class A 90 Degree Elbow to Pipe B09.040.017 2NC89-12 CN-2NC-89 NDE-35 PT SS 2.000 Socket NC CN-2553-1.0 160 0.344 Class A Pipe to Tee B09.040.018 2NC89-13 CN-2NC-89 NDE-35 PT SS 2.000 Socket NC CN-2553-1.0 160 0.344 Class A Tee to Pipe

EOC 14 CATEGORY B-J. Pressure Retaining Welds In DUKE ENERGQ;ORPORATION (

INSERVICE INSPECTION PLAN MANAGEMENT P*eWng Inservice Inspection Database Management System Plan Report Mocket eds Catawba 2 Page 9 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS B09.040.030 2NI306-4 CN-2NI-306 NDE-35 PT SS 1.500 Socket NI CN-2562-1.0 160 0.281 Class A 45 Degree Elbow to Pipe B09.040.031 2NI306-6 CN-2NI-306 NDE-35 PT SS 2.000 Socket NI CN-2562-1 .0 160 0.344 Class A 2X1 1/2 Red Insert to VLV 2NI351 B09.040.032 2NI322-2 CN-2NI-322 NDE-35 PT SS 2.000 Socket NI CN-2562-1.2 160 0.344 Class A Pipe to 90 Degree Elbow B09.040.033 2NI322-4 CN-2NI-322 NDE-35 PT SS 2.000 Socket NI CN-2562-1.2 160 0.344 Class A Pipe to Special Weld Boss B09.040.034 2NI396-13 CN-2NI-396 NDE-35 PT SS 2.000 Socket NI CN-2562-1.2 160 0.344 Class A Tee to Pipe B09.040.035 2NI396-18 CN-2NI-396 NDE-35 PT SS 2.000 Socket NI CN-2562-1.2 160 0.344 Class A Pipe to 90 Degree Elbow B09.040.036 2NI396-20 CN-2NI-396 NDE-35 PT SS 2.000 Socket NI CN-2562-1.2 160 0.344 Class A Pipe to VLV 2NI159 B09.040.037 2NI396-21 CN-2NI-396 NDE-35 PT SS 2.000 Socket NI CN-2562-1.2 160 0.344 Class A 90 Degree Elbow to Pipe Total B09.040 Items: 16 Total B09 Items: 45

EOC 14 ( DUKE ENERGJORPORATION (

CATEGORY B-M-1, Pressure Retaining Welds in INSERVICE INSPECTION PLAN MANAGEMENT Valve Bodies Inservice Inspection Database Management System Plan Report Catawba 2 Page 10 Inservice Inspection Plan for Interval 2 Outage 7 06/2012006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAJTHK CAL BLOCKS COMMENTS

• NPS 4 or Larger; Valve Body Welds ****

B12.040.002B 2ND-37A CN-2ND-66 NDE-3630 UT SS 20.000 50354 Valve Body To Bonnet Circumferential ND CNM-1205.00-262 2.043 Inspect one of the following (1ND-1 B,2A,36B, or Class A 37A)

Total B12.040 Items: 1 Total B12 Items: I

EOC 14 ( DUKE ENERG.JORPORATION

(

CATEGORY C-A, Pressure Retaininq Welds In INSERVICE INSPECTION PLAN MANAGEMENT PIressure Vessels Inservice Inspection Database Management System Plan Report Shell Circumferential Welds Catawba 2 Page 11 Inservlce Inspection Plan for Interval 2 Outage 7 06/20/2006 TEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS Cc)1.010.006 2SWRF-1-3 CN-ISIN2-2554-1.6 NDE-35 PT SS 6.625 Seal Water Re turn Filter. Shell Pc. 1 to Seal Ring Circumferential NV CNM 1201.04-078 0.134 Pc. 3 Class B Shell to Reference Code Case N-435-1.

Seal Ring Total C01.010 Items: 1

EOC 14 CATEGORY C-A. Pressure Retaining Welds In DUKE ENERGQORPORATION (

INSERVICE INSPECTION PLAN MANAGEMENT Pressure Vessels Inservice Inspection Database Management System Plan Report M Crcumferential Welds Catawba 2 Page 12 Inservlce Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS C01.020.001 2SGD-06B-07 CN-2553-1.0 NDE-620 UT CS 0.000 50366 Steam Generator 2D Upper Shell To Upper Head Circumferential NC CNM 2201.01-114 3.890 50236A PC. 6B To PC. 7 Class B Upper Shell to Depending upon the examiner's qualifications, Upper Head Procedure PDI-UT-6 may be used in lieu of Procedure NDE-620.

C01.020.012 2ASWINJF-SH-HD CN-2554-1.2 NDE-12 RT SS 4.000 Seal Water Injection Filter 2A Shell To Head PC. 1 Circumferential NV CNM 1201.04-74 0.674 To PC. 2A Class B Shell to Head Examine with Radiography per Duke Energy Response to NRC Request for Additional Information, pertaining to Request for Relief Serial Number 04-CN-002, dated May 17, 2005.

C01.020.017 2SWRF-1-2 CN-ISIN2-2554-1.6 NDE-35 PT SS 6.625 Seal Water Return Filter Shell To Head PC. 5 To Circumferential NV CNM 1201.04-78 0.134 PC. 6 Class B Filter Shell (Pc. 1) to Reference Code Case N-435-1.

Head (Pc. 2)

Total C01.020 Items: 3 Total C01 items: 4

EOC 14

( DUKE ENERG?,LORPORATION C:

CATEGORY C-B, Pressure Retajning Nozzle INSERVICE INSPECTION PLAN MANAGEMENT Welds In Vessels INozzles Inservice Inspection Database Management System Plan Report In Vessels <=- 12 In. Nomlrnal Thickness Catawba 2 Page 13 Inservice Inspection Plan for Interval 2 Outage 7 06120/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• • • • Nozzle-to-Shell (or Head) Weld ****

C02.011.003 2SWRF-1-OUTLET NDE-35 PT SS 2.000 Seal Water Return Filter Outlet Nozzle Circumferential NV CN-ISIN-2554-1.6 0.154 Reference Code Case N-435-1.

Class B CNM 1201.04-078 Nozzle to Shell Total C02.011 Items: 1

EOC 14

( DUKE ENERJ? CORPORATION C:

CATEGORY C-B, Pressure Retaining Nozzle INSERVICE INSPECTION PLAN MANAGEMENT Welds In Vessels Inselrvice Inspection Database Management System Plan Report N*oNozleWithout Reinforcinq Plate In Vessels> Catawba 2 Page 14 12 In. Nom. Thickness In,.service Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIATHK CAL BLOCKS COMMENTS

• • • • Nozzle-to-Shell (or Head) Weld ****

C02.021.003 2SGD-UH-1 5 NDE-820 UT CS 32.000 50366 Steam Generator 2D Main Steam Nozzle To Upper Circumferential NC CNM-2201.01-102/1 NDE-640 3.820 Head Class B CNM-2201.01-114/1 Nozzle to PC. 7 To PC. 15 Upper Head C02.021.003A 2SGD-UH-15 NDE-25 MT CS 32.000 Steam Generator 2D Main Steam Nozzle To Upper Circumferential NC CNM-2201.01-102/1 3.820 Head Class B CNM-2201.01-114/1 Nozzle to PC. 7 To Pc. 15 Upper Head Total C02.021 Items: 2 Total C02 Items: 3

EOC 14 DUKE ENERG4* CORPORATION C

CATEGORY C-C, Integral Attachments For INSERVICE INSPECTION PLAN MANAGEMENT Vessels, PipinQ, Pumps, And Valves Inservice Inspection Database Management System Plan Report EEIPfng ITEM NUMBER Catawba 2 Inservice Inspection Plan for Interval 2 Outage 7 PROC INSP REQ MAT/SCH DIA/lH-K CAL BLOCKS COMMENTS Page 15 06/20/2006 ID NUMBER SYS ISO/DWG NUMBERS

• • • • Integrally Welded Attachments ****

C03.020.001 2-R-CF.1521 CN-2491-CF002 NDE-25 MT CS 18.000 Welded Attachment Rigid Support CF CN-2591-1.1 0.750 Class B C03.020.004 2-R-CF-1582 CN-2491-CF001 NDE-25 MT CS 18.000 Welded Attachment Rigid Support CF CN-2591-1.1 0.750 Class B C03.020.005 2-R-CF-1563 CN-2491 -CF003 NDE-25 MT CS 18.000 Welded Attachment Spring Hgr CF CN-2591-1.1 0.750 Class B C03.020.010 2-R-CF-1585 CN-2491-CF001 NDE-25 MT CS 18.000 Welded Attachment Spring Hgr CF CN-2591-1.1 0.750 Class B C03.020.054 2-R-NV-0281 CN-2492-NV131 NDE-35 PT SS 3.000 Welded Attachment Rigid Support NV CN-2554-1.7 0.750 Class B Total C03.020 Items: 5

EOC 14 CATEGORY C-C, Integral Attachments For DUKE ENERt(( %ORPORATION C INSERVICE INSPECTION PLAN MANAGEMENT Vessels, Piping, Pumps, And Valves Inservice Inspection Database Management System Plan Report Catawba 2 Page 16 Inservice Inspection Plan for Interval 2 Outage 7 06200/006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DI'ITHK CAL BLOCKS COMMENTS

• • • • Integrally Welded Attachments ****

C03.040.001 2-R-SV-1573 CN-ISIN-2493-1.0 NDE-25 MT CS 0.000 Lug to Valve Rigid Support SV CN-2491 -SV005 1.000 Class B Valve C03.040.002 2-R-SV-1574 CN-ISIN-2493-1.0 NDE-25 MT CS 0.000 Support 2-R-SV-1574 to Forged Bracket on valve Rigid Support SV CN-2491-SV005 1.000 Body.

Class B Forged Bracket C03.040.003 2-R-SV-1553 CN-ISIN-2493-1.0 NDE-25 MT CS 0.000 Lug to Valve Rigid Support SV CN-2491-SV006 1.000 Class B Valve C03.040.004 2-R-SV-1 554 CN-ISIN-2493-1.0 NDE-25 MT CS 0.000 Support 2-R-SV-1554 to Forged Bracket on Valve Rigid Support SV CN-2491-SV006 1.000 Body.

Class B Support to Forged Bracket C03.040.005 2-R-SV-1610 CN-ISIN-2493-1.0 NDE-25 MT CS 0.000 Lug to Valve Rigid Support SV CN-2591-SVO07 1.000 Class B Valve C03.040.006 2-R-SVo1 611 CN-ISIN-2493-1.0 NDE-25 MT CS 0.000 Support 2-R-SV-1611 on valve body.

Rigid Support SV CN-2591-SV007 1.000 Class B Forged Bracket C03.040.007 2-R-SV-1 593 CN-ISIN-2493-1.0 NDE-25 MT CS 0.000 Lug to Valve Rigid Support SV CN-2591 -SV008 1.000 Class B Valve C03.040.008 2-R-SV-1594 CN-ISIN-2493-1.0 NDE-25 MT CS 0.000 Support 2-R-SV-1611 to Forged Bracket on Valve Rigid Support SV CN-2591-SVO08 1.000 Body.

Class B Support to Forged Bracket Total C03.040 items: 8 Total C03 Items: 13

EOC 14 ENERk CORPORATION fDUKE CATEGORY C-F-., Pressure Retaininq Welds In INSERVICE INSPECTION PLAN MANAGEMENT C

Austenitic SS or Hfaqh Alloy Piping Inservice Inspection Database Management System Plan Report WPPi~inaWWlds =3/8 In. Nominal Wall Thickness Catawba 2 Page 17 orPI In >NPS4 Inservice Inspection Plan for Interval 2 Outag e7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DINTHK CA,LBLOCKS COMMENTS

• • • • Circumferential Weld C05.011.073 2ND24-2 CN-2ND-24 NDE-600 UT SS 12.000 * *Reference General Requirements Section 8.1.10.

Circumferential ND CN-25611-1.0 STD 0.375 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.073A 2ND24-2 CN-2ND-24 NDE-35 PT SS 12.000 Circumferential ND CN-2561 -1.0 STD 0.375 Class B Pipe to 90 Degree Elbow C05.011.074 2ND24-4 CN-2ND-24 NDE-600 UT SS 12.000 *Reference General Requirements Section 8.1.10.

Circumferential ND CN-2561-1.0 STD 0.375 Depending on the examiner's qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.074A 2ND24-4 CN-2ND-24 NDE-35 PT SS 12.000 Circumferential ND CN-2561-1.0 STD 0.375 Class B 90 Degree Elbow to Pipe C05.011,075 2ND24-6 CN-2ND-24 NDE-600 UT SS 12.000 *Reference General Requirements Section 8.1.10.

Circumferential ND CN-2561-1.0 STD 0.375 Depending on the examiners qualifications, Class B Elbow 90 Degree to Procedure PDI-UT-2 may be used in lieu of Elbow 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.075A 2ND24-6 CN-2ND-24 NDE-35 PT SS 12.000 Circumferential ND CN-2561-11.0 STD 0.375 Class B Elbow 90 Degree to Elbow 90 Degree Elbow C05.011.076 2ND24-8 CN-2ND-24 NDE-600 UT SS 12.000 *

• Reference General Reouirements Section 8.1110 Circumferential ND CN-2561-1.0 STD 0.375 50313 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 DUKE ENERGY CORPORATION CATEGORY C-F-i, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT

(

Austenitic SS or HI-qh Alloy Piping Inservlce Inspection Database Management System Plan Report Welds >= 3/8 In.

iPIDIna Nominal Wall Thickness Catawba 2 Page 18 EoPipng > NPS 4 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.0111.076A 2ND24-8 CN-2ND-24 NDE-35 PT SS 12.000 Circumferential ND CN-2561-1.0 STD 0.375 Class B Pipe to 90 Degree Elbow C05.011.077 2ND24-16 CN-2ND-24 NDE-600 UT SS 12.000 *

• Reference General Requirements Section 8.1.10 Circumferential ND CN-2561-1.0 STD 0.375 50313 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of Flange NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.077A 2ND24-16 CN-2ND-24 NDE-35 PT SS 12.000 Circumferential ND CN-2561-1.0 STD 0.375 Class B Pipe to Flange C05.011.083 2ND46-6 CN-2ND-46 NDE-600 UT SS 12.000 *

• Reference General Requirements Section 8.1.10 Circumferential ND CN-2561-1.0 STD 0.375 50313 Depending on the examiners qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.083A 2ND46-6 CN-2ND-46 NDE-35 PT SS 12.000 Circumferential ND CN-2561-1.0 STD 0.375 Class B 90 Degree Elbow to Pipe C05.011.114 2NI73-10 CN-2NI-73 NDEo600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiner's qualifications, Class B Flange to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.114A 2NI73-10 CN-2NI-73 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B Flange to Pipe C05.011.115 2NI73-11 CN-2NI-73 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-2 may be used In lieu of Flange NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 ( DUKE ENERc( .;ORPORATION (

CATEGORY C-F-i. Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS or High Alloy Piping Inservice Inspection Database Management System Plan Report N >= 3/8 In. Nominal Wall Thickness Pi~inaWWlds Catawba 2 Page 19 for Pin >NPS4 Inservice Inspection Plan for Interval 2 Outag e 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAkL BLOCKS COMMENTS C05.011.115A 2NI73-11 CN-2NI-73 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B Pipe to Flange C05.011.116 2NI73-2 CN-2NI-73 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.116A 2NI73-2 CN-2NI-73 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B Pipe to 90 Degree Elbow C05.011.117 2NI73-4 CN-2NI-73 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B 45 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

C05.011.117A 2NI73-4 CN-2NI-73 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B 45 Degree Elbow to Pipe C05.011.118 2NI76-2 CN-2NI-76 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.118A 2NI76-2 CN-2NI-76 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B 90 Degree Elbow to Pipe t'nf nil 11I 0 OMIKI.IQ P.OMI.7TdI MfI:_fI9n I IT a0 **

M * *n f-/ Q-! a 4 in I, I l , l VW ,

W a, flNl*la l I4,,-

9 a, , r l, a .UII * .. I

• IV.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

1 (oc DUKE ENERC CORPORATION (

CATEGORY C-F-l. Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS or High Alloy Piping Inservice Inspection Database Management System Plan Report Elon WWlds >=3/8 in. Nominal Wall Thickness Catawba 2 Page 20 orPipin >NPS4 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.011.119A 2NI76-3 CN-2NI-76 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B Pipe to 90 Degree Elbow C05.011.120 2NI76-4 CN-2NI-76 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.120A 2NI76-4 CN-2NI-76 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B 90 Degree Elbow to Pipe C05.011.121 2NI76-5 CN-2NI-76 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examineres qualifications, Class B Pipe to Procedure PDI-UT-2 may be used In lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.121A 2NI76-5 CN-2NI-76 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B Pipe to 90 Degree Elbow C05.011.149 2NI89-1 CN-2NI-89 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B 45 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.149A 2NI89-1 CN-2NI-89 NDE-35 PT SS 6.000

' Circumferential NI CN-2562-1.3 160 0.719 Class B 45 Degree Elbow to Pipe frl ^4 4 4 CA nfljfl A f^ k II K111 I'I4U-OUU UI 0 O.UUU 4.... ~ r...!~...

nuluren;e Geuiiwral nequiremenui oSectioln 8. I. I U.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examinees qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 DUKE ENER*;i CORPORATION

(

CATEGORY C-F-i, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS or Hlgh Alloy Pipin" Inservice Inspection Database Management System Plan Report NP Welds >= 318 In. Nominal Wall Thickness Pllnn Catawba 2 Page 21 orPipin >NPS4 Inservlce Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.011.150A 2NI89-4 CN-2NI-89 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B Pipe to 90 Degree Elbow C05.011.151 2NI89-5 CN-2NI-89 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

C05.011.151A 2NI89-5 CN-2NI-89 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B 90 Degree Elbow to Pipe C05.011.152 2NI89-6 CN-2NI-89 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.152A 2NI89-6 CN-2NI-89 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B Pipe to 90 Degree Elbow C05.011.153 2NI89-7 CN-2NI-89 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examinees qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

C05.011.153A 2NI89-7 CN-2NI-89 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B 90 Degree Elbow to Pipe C05.011.154 2NI89-10 CN-2NI-89 NDE-600 UT SS 6.000 *Reference General Reauirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used In lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 CATEGORY C-F-I. Pressure Retaining Welds In DUKE ENERcC CORPORATION INSERVICE INSPECTION PLAN MANAGEMENT C

Austenitic SS or Hih Alloy Pilina Inservice Inspection Database Management System Plan Report M >=3/8 In. Nominal Wall Thickness i~ing Welds Catawba 2 Page 22 orPi in >NPS4 InservIce Inspection Plan for Interval 2 Outag e7 06/202006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MATISCH DIA/ITHK CA L BLOCKS COMMENTS C05.011.154A 2NI89-10 CN-2NI-89 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B Pipe to 90 Degree Elbow C05.011.155 2NI89-11 CN-2NI-89 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examiners qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used In lieu of Pipe NDE-600. If PDI-UT-2 Is used, Calibration Block PDI°UT-2-C may be used.

C05.011.155A 2NI89-11 CN-2NI-89 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B 90 Degree Elbow to Pipe C05.011.160 2NI76-6 CN-2NI-76 NDE-600 UT SS 6.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.719 Depending on the examineres qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used In lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.011.160A 2NI76-6 CN-2NI-76 NDE-35 PT SS 6.000 Circumferential NI CN-2562-1.3 160 0.719 Class B 90 Degree Elbow to Pipe Total C05.011 items: 44

EOC 14 ( DUKE ENER(. CORPORATION

(

CATEGORY C-F-i. Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS or High Alloy Piping Inservice Inspection Database Management System Plan Report WP IDWel US In. Nom Wall For Ploln >=

Wlds> Catawba 2 Page 23 NPS2And<-NP 4 Inservice Inspection Plan for Interval 2 Outag e 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REG MAT/SCH DIATIHK CA v..

• LBLOCKS COMMENTS Circumferential Weld C05.021.121 2NI303-1 CN-2NI-303 NDE-600 UT SS 4.000 * *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.531 Depending on the examiner's qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.121A 2NI303-1 CN-2NI-303 NDE-35 PT SS 4.000 Circumferential NI CN-2562-1.3 160 0.531 Class B 90 Degree Elbow to Pipe C05.021.122 2NI303-10 CN-2NI-303 NDE-600 UT SS 4.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.531 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

C05.021.122A 2NI303-10 CN-2NI°303 NDE-35 PT SS 4.000 Circumferential NI CN-2562-1.3 160 0.531 Class B Pipe to 90 Degree Elbow C05.021.123 2NI303-13 CN-2NI-303 NDE-600 UT SS 4.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.531 Depending on the examiner's qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.123A 2NI303-13 CN-2NI-303 NDE-35 PT SS 4.000 Circumferential NI CN-2562-1.3 160 0.531 Class B 90 Degree Elbow to Pipe C05.021.124 2NI303-14 CN-2NI-303 NDE-600 UT SS 4.000 *Reference General ReAnuirements Sretion R1 10 Circumferential NI CN-2562-1.3 160 0.531 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 ( DUKE ENERC( .;ORPORATION C CATEGORY C-F-I, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS or Hi-fh Alloy Piping Inservice Inspection Database Management System Plan Report EEiRIng Welds> 1/5 In. Nom Wall For Piping >= Catawba 2 Page 24 PS 2 And <= NPS 4 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIANTHK CAL BLOCKS COMMENTS C05.021.124A 2NI303-14 CN-2NI-303 NDE-35 PT SS 4.000 Circumferential NI CN-2562-1.3 160 0.531 Class B Pipe to 90 Degree Elbow C05.021.125 2NI309-10 CN-2NI-309 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.0 160 0.438 Depending on the examiners qualifications, Class B Tee to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.125A 2NI309-10 CN-2NI-309 NDE-35 PT SS 3.000 Circumferential NI CN-2562-1.0 160 0.438 Class B Tee to Pipe C05.021.126 2NI309-11 CN-2NI-309 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.0 160 0.438 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.126A 2NI309-11 CN-2NI-309 NDE-35 PT SS 3.000 Circumferential NI CN-2562-1.0 160 0.438 Class B Pipe to 90 Degree Elbow C05.021.127 2NI369-19 CN-2NI-369 NDE-600 UT SS 2.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.2 160 0.344 Depending on the examiners qualifications, Class B 4X2 Reducer to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.127A 2NI369-19 CN-2NI-369 NDE-35 PT SS 2.000 Circumferential NI CN-2562-1.2 160 0.344 Class B 4X2 Reducer to Pipe C05.021.128 2NI369-8 CN-2NI-369 NDE-600 UT SS 2.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.2 160 0.344 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of Orf. Flange NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 ( DUKE ENERGC  %.ORPORATION C

CATEGORY C-F-l. Pressure Retainingi Welds In INSERVICE INSPECTION PLAN MANAGEMENT AustenitIc SS or Hi-gh Alloy Pipinq Inservice Inspection Database Management System Plan Report 0P1lInq Welds > 1/5 In. Nom Wall For Plpln-q >= Catawba 2 Page 25 MNPS 2 And <= NPS 4 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.021.128A 2NI369-8 CN-2NI-369 NDE-35 PT SS 2.000 Circumferential NI CN-2562-1.2 160 0.344 Class B Pipe to Orf. Flange C05.021.129 2NI68-2 CN-2NI-68 NDE-600 UT SS 4.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.531 Depending on the examiners qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.129A 2NI68-2 CN-2NI-68 NDE-35 PT SS 4.000 Circumferential NI CN-2562-1.3 160 0.531 Class B 90 Degree Elbow to Pipe C05.021.130 2NI68-10 CN-2NI-68 NDE-600 UT SS 4.000 *Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.3 160 0.531 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.130A 2NI68-10 CN-2NI-68 NDE-35 PT SS 4.000 Circumferential NI CN-2562-1.3 160 0.531 Class B Pipe to 90 Degree Elbow C05.021.250 2NV47-17 CN-2NV-47 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NV CN-2554-1.2 160 0.438 Depending on the examiners qualifications, Class B 45 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.250A 2NV47-17 CN-2NV-47 NDE-35 PT SS 3.000 Circumferential NV CN-2554-1.2 160 0.438 Class B 45 Degree Elbow to Pipe C05.021.251 2NV47-18 CN-2NV-47 NDE-600 UT SS 3.000 *Reference General Reauirements Section 8.1.10.

Circumferential NV CN-2554-1.2 160 0.438 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used In lieu of 45 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 ( DUKE ENERG.,;ORPORATION C

CATEGORY C-F-l, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitlc SS or Hifgh Alloy Pipinq Inservice Inspection Database Management System Plan Report WPIDlno Welds> 115 In. Nom Wall For Piing >= Catawba 2 Page 26 ENPS 2 And,<-- NPS4 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DINTHK CAL BLOCKS COMMENTS C05.021.251 A 2NV47-1 8 CN-2NV-47 NDE-35 PT SS 3.000 Circumferential NV CN-2554-1.2 160 0.438 Class B Pipe to 45 Degree Elbow C05.021.252 2NV47-9 CN-2NV-47 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NV CN-2554-1.2 160 0.438 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.252A 2NV47-9 CN-2NV-47 NDE-35 PT SS 3.000 Circumferential NV CN-2554-1.2 160 0.438 Class B Pipe to 90 Degree Elbow C05.021.253 2NV47-20 CN-2NV-47 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NV CN-2554-1.2 160 0.438 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-2 may be used In lieu of 45 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.253A 2NV47-20 CN-2NV-47 NDE-35 PT SS 3.000 Circumferential NV CN-2554-1.2 160 0.438 Class B Pipe to 45 Degree Elbow C05.021.254 2NV489-12 CN-2NV-489 NDE-600 UT SS 4.000 *Reference General Requirements Section 8.1.10.

Circumferential NV CN-2554-1.6 40 0.237 Depending on the examiner's qualifications, Class B 45 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.254A 2NV489-12 CN-2NV-489 NDE-35 PT SS 4.000 Circumferential NV CN-2554-1.6 40 0.237 Class B 45 Degree Elbow to Pipe C05.021.255 2NV489-13 CN-2NV-489 NDE-600 UT SS 4.000 *Reference General Reauirements Section 8.1.10.

Circumferential NV CN-2554-1.6 40 0.237 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 45 Degree Elbow NDE-600. If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 DUKE ENER4?..ORPORATlON C

CATEGORY C-F-i. Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS or Hlgh Alloy Piping Inservice Inspection Database Management System Plan Report i Pllna Welds > 1/5 In. Norm Wall For P! Ina >= Catawba 2 Page 27 06/20/2006 NPS 2 And <= NPS 4 InservIce Inspection Plan for Interval 2 Outagqe7 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIN/THK CAL BLOCKS COMMENTS C05.021.255A 2NV489-13 CN-2NV-489 NDE-35 PT SS 4.000 Circumferential NV CN-2554-1.6 40 0.237 Class B Pipe to 45 Degree Elbow C05.021.256 2NV49-8 CN-2NV-49 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NV CN-2554-1.2 160 0.438 Depending on the examiners qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.256A 2NV49-8 CN-2NV-49 NDE-35 PT SS 3.000 Circumferential NV CN-2554-1.2 160 0.438 Class B 90 Degree Elbow to Pipe C05.021.257 2NV49-9 CN-2NV-49 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NV CN-2554-1.2 160 0.438 Depending on the examiners qualifications, Class B Pipe to Procedure PDI-UT-2 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.257A 2NV49-9 CN-2NV-49 NDE-35 PT SS 3.000 Circumferential NV CN-2554-1.2 160 0.438 Class B Pipe to 90 Degree Elbow C05.021.258 2NV50-15 CN-2NV-50 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NV CN-2554-1.7 40 0.216 Depending on the examiners qualifications, Class B 90 Degree Elbow to Procedure PDI-UT-2 may be used in lieu of Pipe NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

C05.021.258A 2NV50-15 CN-2NV-50 NDE-35 PT SS 3.000 Circumferential NV CN-2554-1.7 40 0.216 Class B 90 Degree Elbow to Pipe C05.021.259 2NV50-16 CN-2NV-50 NDE-600 UT SS 3.000 *Reference General Requirements Section 8.1.10.

Circumferential NV CN-2554-11.7 40 0.216 Depending on the examiners qualifications, Pipe to Procedure PDI-UT-2 may be used in lieu of Class B 90 Degree Elbow NDE-600. If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 C DUKE ENERGQ-.;ORPORATION (

CATEGORY C-F-I. Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT AustenItlc SS or High Alloy Piping EPllona Welds > 1/5 In. Nom Wall For Plplnjq >=

NNPS 2 And <= NPS 4 InservIce Inspection Database Management System Inservlce Catawba 2 Inspection Plan for Interval 2 Outage 7 Plan Report Page 28 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIArTHK CAL BLOCKS COMMENTS C05.021.259A 2NV50-16 CN-2NV-50 NDE-35 PT SS 3.000 Circumferential NV CN-2554-1.7 40 0.216 Class B Pipe to 90 Degree Elbow Total C05.021 items: 40

EOC 14 DUKE ENERGC ,.ORPORATION CATEGORY C-F-2, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT

(

Carbon Or Low Alloy Steel Piping Inservice Inspection Database Management System Plan Report NPi In Welds >= 3L8 in,.Nomlnal Wall Thickness Catawba 2 Page 29 Efor PipIng > NPS 4 Inservlce Inspection Plan for Interval 2 Outage 7 06120/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• • • • Circumferential Weld ****

C05.051.009 2CA93-1 CN-2CA-93 NDE-600 UT CS 6.000

• Steam Generator 2C Circumferential CA CN-2592-1.1 80 0.432 *Reference General Requirements Section 8.1.10.

Class B Term end 90 Degree Elbow to Depending on the examiner's qualifications, 2CSG Nozzle Procedure PDI-UT-1 may be used in lieu of NDE-600. If PDI-UT-1 is used, Calibration Block PDI-UT-1-C may be used.

C05.051.009A 2CA93-1 CN-2CA-93 NDE MT CS 6.000 Steam Generator 2C Circumferential CA CN-2592-1.1 80 0.432 Class B Term end 90 Degree Elbow to 2CSG Nozzle C05.051.011 2CA97-1 CN-2CA-97 NDE-600 UT CS 6.000 Steam Generator 2A Circumferential CA CN-2592-1.1 80 0.432 *Reference General Requirements Section 8.1.10.

Class B Term end 90 Degree Elbow to Depending on the examiner's qualifications, 2ASG Nozzle Procedure PDI-UT-1 may be used in lieu of NDE-600. If PDI-UT-1 is used, Calibration Block PDI-UT-1-C may be used.

C05.051.01 1A 2CA97-1 CN-2CA-97 NDE-25 MT CS 6.000 Steam Generator 2A Circumferential CA CN-2592-1.1 80 0.432 Class B Term end 90 Degree Elbow to 2ASG Nozzle C05.051.103 2SM12-4 CN-2SM-12 NDE-600 UT CS 34.000 *Reference General Requirements Section 8.1.10.

Circumferential SM CN-2593-1.0 1.375 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-1 may be used in lieu of 90 Degree Elbow NDE-600. If PDI-UT-1 is used, Calibration Block PDI-UT-1-C may be used.

C05.051.103A 2SM12-4 CN-2SM-12 NDE-25 MT CS 34.000 Circumferential SM CN-2593-1.0 1.375 Class B Pipe to 90 Degree Elbow C05.051.110 2SM-8A-B CN-2SM-57 NDE-600 UT CS 10.000 *Reference General Requirements Section 8.1.10.

Circumferential SM CN-2593-1.0 1.500 Depending on the examiner's qualifications, Class B Outlet to Procedure PDI-UT-1 may be used in lieu of Transition Piece NDE-600. If PDI-UT-1 is used, Calibration Block PDI-UT-1-C may be used.

EOC 14 ( DUKE ENERG(.,ORPORATION CATEGORY C-F-2. Pressure Retalnlng Welds In INSERVICE INSPECTION PLAN MANAGEMENT Carbon Or Low Alloy Steel Pilpin Inservice Inspection Database Management System Plan Report NPPlonnoWelds >=3/8 In. Nominal Wall Thickness Catawba 2 Page 30 for Pin >NPS4 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.051.11OA 2SM-8A-B CN-2SM-57 NDE-25 MT CS 10.000 Circumferential SM CN-2593-1.0 1.500 Class B Outlet to Transition Piece C05.051.111 2SM-8A-F CN-2SM-57 NDE-600 UT CS 10.000 *Reference General Requirements Section 8.1.10.

Circumferential SM CN-2593-1.0 1.500 Depending on the examiner's qualifications, Class B Outlet to Procedure PDI-UT-1 may be used in lieu of Transition Piece NDE-600. If PDI-UT-1 is used, Calibration Block PDI-UT-1-C may be used.

C05.051.111A 2SM-8A-F CN-2SM-57 NDE-25 MT CS 10.000 Circumferential SM CN-2593-1.0 1.500 Class B Outlet to Transition Piece C05.051.153 2SV19-3 CN-2SV-19 NDE-600 UT CS 9.000 *Reference General Requirements Section 8.1.10.

Circumferential SV CN-2593-1.0 40 1.500 Depending on the examiner's qualifications, Class B Pipe to Procedure PDI-UT-1 may be used in lieu of VLV 2SV004 NDE-600. If PDI-UT-1 is used, Calibration Block PDI-UT-1-C may be used.

C05.051.153A 2SV19-3 CN-2SV-19 NDE-25 MT CS 9.000 Circumferential SV CN-2593-1.0 40 1.500 Class B Pipe to VLV 2SV004 Total C05.051 Items: 12

EOC 14 ( DUKE ENERGCORPORATION (

CATEGORY C-F-2. Pressure Retalnlng Welds In INSERVICE INSPECTION PLAN MANAGEMENT Carbon Or Low Alloy Steel PIDInq Inservlce Inspection Database Management System Plan Report Ploe Branch Connections of Branch Piping >= Catawba 2 Page 31 NPS 2 Inservice Inspection Plan for Interval 2 Outag e7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MATISCH DIA/THK CA*L BLOCKS COMMENTS

• • • • Circumferential Weld ****

C05.081.001 2SM-5A-C CN-2SM-059 NDE-25 MT CS 6.000 Grinnell Piece Mark CW-SM-5A Weld C Branch SM CN-2593-1.0 0.432 Class B Pipe Main Header to Sweepolet Total C05.081 Items: 1 Total COS items: 97

EOC14 1 CATEGORY C-G. Pressure Retaininq Welds In DUKE ENERG(-,.;ORPORATION (

INSERVICE INSPECTION PLAN MANAGEMENT Pumps And Valves Inservice Inspection Database Management System Plan Report Catawba 2 Page 32 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS t

'

• Valve Body Welds ***

C06.020.016 2SA-1 NDE-25 MT CS 6.000 Valve Body Weld - Valve Numbers in Valve Group Circumferential SA CN-2593-1.1 1.164 2SA-1,2SA-4 Class B CNM-1205.00-117 Valve Body to Bonnet C06.020.018 2SV-10 NDE-35 PT SS-CS 9.000 Valve Body Weld - Valve Numbers in Valve Group Circumferential SV CN-2593-1.0 1.500 2SV-8, 2SV-9, 2SV-1 0, 2SV-1 1, 2SV-1 2 Class B CNM-1205.09-02 Valve to Pipe Inlet Neck To Base C06.020.019 2SVo14 NDE-35 PT SS-CS 9.000 Valve Body Weld - Valve Numbers in Valve Group Circumferential SV CN-2593-1.0 1.500 2SV-14, 2SV-15, 2SV-16, Class B CNM-1205.09-02 Valve to 2SV-17, 2SV-18 Pipe Inlet Neck To Base C06.020.020 2SV-20 NDE-35 PT SS-CS 9.000 Valve Body Weld - Valve Numbers in Valve Group Circumferential SV CN-2593-1.0 1.500 2SV-20, 2SV-21,2SV-22, Class B CNM-1205.09-02 Valve to 2SV-23, 2SV-24 Pipe Inlet Neck To Base Total C06.020 Items: 4 Total C06 Items: 4

EOC 14 (

CATEGORY D-B, Systems In Support Of ECC, DUKE ENERGC".;ORPORATION INSERVICE INSPECTION PLAN MANAGEMENT C

CHR, Atmos. Cleanup, And Reactor RHR Inservice Inspection Database Management System Plan Report an!iLterlAtachment Catawba 2 Page 33 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS IS()/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

-*** Component Supports and Restraints ****

D02.020.001 2-R-CA-0142 CN-2492-CA051 OAL-14 VT-3 NA 4.000 Welded Attachments To Be Done With F01.031.015 Rigid Support CA CN-2592-1.1 1.000 Class C D02.020.007 2-R-KC-0313 CN-2492-KC090 QAL-14 VT-3 NA 6.000 Welded Attachment Rigid Support KC CN-2573-1.1 0.625 To Be Done With F01.030.072 Class C D02.020.014 2-R-RN-0226 CN-2493-RN001 OAL-14 VT-3 NA 10.000 Welded Attachment Rigid Support RN CN-2574-2.5 0.750 To Be Done With F01.031.153 Class C D02.020.015 2-R-RN-0239 CN-2493-RN029 QAL-14 VT-3 NA 10.000 Welded Attachment Rigid Support RN CN-2574-2.1 0.750 To Be Done With F01.031.154 Class C D02.020.018 2-RNPB-SUPPORT QAL-14 VT-3 NA 0.000 Nuclear Service Water Pump 2B Rigid Support RN CN-ISIN-1574-1.2 0.000 Welded Attachment Class C CNM 1201.05-122 Stiffners to To be done with F01.040.219 Pump Casing Total D02.020 items: 5 Total D02 Items: 5

EOC 14(

CAEORY F-ASpprs DUKE ENERGcfORPORATION C INSERVICE INSPECTION PLAN MANAGEMENT Inservlce Inspection Database Management System Plan Report M~las 1Pt Ing Supports Catawba 2 Page 34 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS I One-Directional F01.010.003 2-R-NC-2002 CN-2491-NCO09 QAL-14 VT-3 NA 2.000 Rigid Support NC CN-2553-1.0 0.000 Class A F01.010.004 2-R-NC-2005 CN-2491-NCO09 OAL-14 VT-3 NA 2.000 Rigid Support NC CN-2553-1.0 0.000 Class A F01.010.007 2-R-NC-1501 CN-2491-NCO160 OAL-14 VT-3 NA 14.000 Rigid Support NC CN-2553-1.0 0.000 Class A Total F01.010 Items: 3

• • • • Thermal Movement ItA*

F01.012.013 2-R-NC-1693 CN-2491-NC099 QAL-14 VT-3 NA 6.000 Mech Snubber NC CN-2553-1.1 0.000 Class A Total F01.012 Items: 1

EOC 14 CATEGORY F-A. Supports DUKE ENERGk 4;ORPORATION INSERVICE INSPECTION PLAN MANAGEMENT C

Inservice Inspection Database Management System Plan Report Mims 2PInSup s Catawba 2 Page 35 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMFNTS

• • • • One-Directional ****

F01.020.039 2-R-ND-0140 CN-2492-ND031 QAL-14 VT-3 NA 12.000 Rigid Support ND CN-2561-1.1 0.000 Class B F01.020.040 2-R-ND-0141 CN-2492-ND031 OAL-14 VT-3 NA 12.000 Rigid Support ND CN-2561-1.1 0.000 Class B F01.020.041 2-R-ND-0246 CN-2492-ND031 QAL-14 VT-3 NA 12.000 Rigid Support ND CN-2561-1.1 0.000 Class B F01.020.042 2-R-ND-0247 CN-2492-ND032 QAL-14 VT-3 NA 8.000 Rigid Support ND CN-2561-1.1 0.000 Class B F01.020.043 2-R-ND-0248 CN-2492-ND032 QAL-14 VT-3 NA 8.000 Rigid Support ND CN-2561-1.1 0.000 Class B F01.020.044 2-R-ND-0318 CN-2492-ND032 QAL-14 VT-3 NA 8.000 Rigid Support ND CN-2561-1.1 0.000 Class B F01.020.074 2-R-NI-0040 CN-2492-NI017 QAL-14 VT-3 NA 4.000 Rigid Support NI CN-2562-1.2 0.000 Class B F01.020.075 2-R-NI-0045 CN-2492-NI017 OAL-14 VT-3 NA 4.000 Rigid Support NI CN-2562-1.2 0.000 Class B

EOC 14 CAEORYO Sports DUKE ENERG( .,ORPORATION INSERVICE INSPECTION PLAN MANAGEMENT C

Inservice Inspection Database Management System Plan Report Catawba 2 Page 36

=Clss2 PI~naSupports Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DINATHK CAL BLOCKS COMMENTS F01.020.076 2-R-NI-0047 CN-2492-NI017 QAL-14 VT-3 NA 4.000 Rigid Support NI CN-2562-1.2 0.000 Class B F01.020.077 2-R-NI-0048 CN-2492-NI017 OAL-14 VT-3 NA 4.000 Rigid Support NI CN-2562-1.2 0.000 Class B F01.020.106 2-R-NS-1011 CN-2491-NS017 QAL-14 VT-3 NA 8.000 Rigid Support NS CN-2563-1.0 0.000 Class B F01.020.107 2-R-NS-1018 CN-2491-NS016 OAL-14 VT-3 NA 8.000 Rigid Support NS CN-2563-1.0 0.000 Class B F01.020.108 2-R-NS-1019 CN-2491-NS016 QAL-14 VT-3 NA 8.000 Rigid Support NS CN-2563-1.0 0.000 Class B F01.020.162 2-R-NV-0006 CN-2492-NV068 QAL-14 VT-3 NA 4.000 Rigid Support NV CN-2554-1.7 0.000 Class B F01.020.163 2-R-NV-0007 CN-2492-NV068 QAL-14 VT-3 NA 4.000 Rigid Support NV CN-2554-1.7 0.000 Class B F01.020.164 2-R-NV-0252 CN-2492-NVO70 OAL-14 VT-3 NA 3.000 Rigid Support NV CN-2554-1.2 0.000 Class B F01.020.165 2-R-NV-0254 CN-2492-NVO70 QAL-14 VT-3 NA 3.000 Rigid Support NV CN-2554-1.2 0.000 Class B

EOC 14 -

CATEGORY F-A. Supports DUKE ENERG( .,ORPORATION INSERVICE INSPECTION PLAN MANAGEMENT C

Inservice Inspection Database Management System Plan Report M~las2 PIRInS.upports Catawba 2 Page 37 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS F01.020.166 2-R-NV-0255 CN-2492-NVO70 QAL-14 VT-3 NA 3.000 Rigid Support NV CN-2554-1.2 0.000 Class B F01.020.223 2-R-SV-1589 CN-2491-SVO08 QAL-14 VT-3 NA 6.000 Rigid Support SV CN-2593-1 .0 0.000 Class B F01.020.224 2-R-SV-1591 CN-2491 -SV008 OAL-14 VT-3 NA 6.000 Rigid Support SV CN-2593-1.0 0.000 Class B Total F101.020 Items: 20

• • • • Multidlrectional ****

F01.021.035 2-R-ND-0322 CN-2492-ND026 QAL-14 VT-3 NA 8.000 Rigid Support ND CN-2561-1.1 0.000 Class B F01.021.078 2-R-NI-1783 CN-2491-NI090 QAL-14 VT-3 NA 4.000 Rigid Support NI CN-2562-1.2 0.000 Class B F01.021.079 2-R-NI-1785 CN-2491-NI090 OAL-14 VT-3 NA 4.000 Rigid Support NI CN-2562-1.2 0.000 Class B F01.021.080 2-R-NI-1786 CN-2491-NI090 OAL-14 VT-3 NA 4.000 Rigid Support NI CN-2562-1.2 0.000 Class B F01.021.104 2-R-NS-0063 CN-2492-NS013 OAL-14 VT-3 NA 10.000 Rigid Support NS CN-2563-1.0 0.000 Class B

EOC 14 CATEGORY F-A, Supports DUKE ENERG( ,.;ORPORATION C INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report M~lss2PipingSupports Catawba 2 Page 38 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS F01.021.105 2-R-NS-0068 CN-2492-NS013 OAL-14 VT-3 NA 10.000 Rigid Support NS CN-2563-1.0 0.000 Class B F01.021.162 2-R-NV-0251 CN-2492-NV070 QAL-14 VT-3 NA 3.000 Rigid Support NV CN-2554-1.2 0.000 Class B F01.021.163 2-R-NV-0253 CN-2492-NVO70 GAL-14 VT-3 NA 3.000 Rigid Support NV CN-2554-1.2 0.000 Class B F01.021.164 2-R-NV-0289 CN-2492-NV072 OAL-14 VT-3 NA 8.000 Rigid Support NV CN-2554-1.7 0.000 Class B F01.021.165 2-R-NV-0290 CN-2492-NV072 OAL-14 VT-3 NA 8.000 Rigid Support NV CN-2554-1.7 0.000 Class B Total F01.021 Items: 10

EOC 14 r DUKE ENERGY %;ORPORATION C CAEORY F-ASu&pors INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 39 M~ls3 PIDIncSuRorts Inservice Inspection Plan for Interval 2 Outage 7 06120/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• • • • One-Directional F01.030.072 2-R-KC-0313 CN-2492-KC090 GAL-14 VT-3 NA 6.000 To Be Done With D02.020.007 Rigid Support KC CN-2573-1.1 0.000 Class C F01.030.122 2-R-LD-0016 CN-2493-LD030 OAL-14 V'-3 NA 6.000 Rigid Support LD CN-2609-2.0 0.000 Class C Total F01.030 Items: 2

• • • • Multldirectlonal ****

F01.031.015 2-R-CA-0142 CN-2492-CA051 QAL-14 VT-3 NA 4.000 To Be Done With D02.020.001 Rigid Support CA CN-2592-1.1 0.000 Class C F01.031.057 2-R-KC-0252 CN-2492-KC101 QAL-14 VT-3 NA 8.000 Rigid Support KC CN-2573-1.0 0.000 Class C F01.031.058 2-R-KC-0253 CN-2492-KC101 QAL-14 VT-3 NA 8.000 Rigid Support KC CN-2573-1.0 0.000 Class C F01.031.059 2-R-KC-0347 CN-2492-KC1 10 GAL-14 VT-3 NA 6.000 Rigid Support KC CN-2573-1.1 0.000 Class C F01.031.060 2-R-KC-0218 CN-2492-KC1 17 QAL-14 VT-3 NA 14.000 Rigid Support KC CN-2573-1.2 0.000 Class C F01.031.061 2-R-KC-0219 CN-2492-KC117 QAL-14 VT-3 NA 14.000 Rigid Support KC CN-2573-1.2 0.000 Class C

EOC 14 DUKE ENER(t CORPORATION CATEGORY F-A. Supports INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report M~as3PIPina Spoors Catawba 2 Page 40 Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS F01.031.062 2-R-KC-0221 CN-2492-KC1 17 QAL-14 VT-3 NA 14.000 Rigid Support KC CN-2573-1.2 0.000 Class C F01.031.153 2-R-RN-0226 CN-2493-RN001 QAL-14 VT-3 NA 10.000 To Be Done With D02.020.014 Rigid Support RN CN-2574-2.5 0.000 Class C F01.031.154 2-R-RN-0239 CN-2493-RN029 QAL-14 VT-3 NA 10.000 To Be Done With D02.020.015 Rigid Support RN CN-2574-2.1 0.000 Class C Total F101.031 items: 9

• • • • Thermal Movement ****

F01.032.104 2-R-KD-0033 CN-2493-KD048 OAL-14 VT-3 NA 8.000 Mech Snubber KD CN-2609-1.0 0.000 Class C F01.032.105 2-R-KD-0007 CN-2493-KD052 QAL-14 VT-3 NA 6.000 Spring Hgr KD CN-2609-1.0 0.000 Class C F01.032.153 2-R-RN-0037 CN-2492-RN139 QAL-14 VT-3 NA 6.000 Mech Snubber RN CN-2574-2.0 0.000 Class C Total F01.032 Items: 3

EOC 14 DUKE ENER(, %;ORPORATION C CATEGORY F-A, Supports INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 41 Mims 12 3. Suppors Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS

• • • • Supports Other Than Piping Supports ****

F01.040.101 2SGA-SUPPORT CN-1070-30 QAL-14 VT-3 NA 0.000 Steam Generator 2A Upper Lateral Support And Rigid Support NC CN-2553-1.0 0.000 Snubbers Class B F01.040.103 2REGHX-SUPPORT CN-2554-1.0 OAL-14 VT-3 NA 0.000 Regenerative Heat Exchanger Support Rigid Support CNM 1201.06-31 0.000 6 Brackets Class B F01.040.109 2SWRF-SUPPORT CN-ISIN-2554-1.6 OAL-14 VT-3 NA 6.000 Seal Water Return Filter Support and Legs Rigid Support NV CNM 1201.04-078 0.250 Class B F01.040.1 10 2CCPA-SUPPORT CN-2554-1.7 OAL-14 VT-3 NA 0.000 Centrifugal Charging Pump 2A Support Rigid Support CNM 1201.05-144 0.000 Class B F01.040.219 2RNPB-SUPPORT QAL-14 VT-3 NA 0.000 Nuclear Service Water Pump 2B Support Rigid Support RN CN-ISIN-1574-1.2 0.000 To be done with D02.020.018 Class C CNM 1201.05-122 F01.040.220 2RNSB-SUPPORT QAL-14 VT-3 NA 0.000 Nuclear Service Water Strainer 2B Support Rigid Support RN CN-ISIN-1574-1.2 0.000 Class C CNM 1218.02-0010 Total F01.040 Items: 6 Total F01 items: 54

EOC 14 ( C DUKE ENERG( 60RPORATION CATEGORY ELC, Elective Inspections INSERVICE INSPECTION PLAN MANAGEMENT Inservlce Inspection Database Management System SNI Cold Lea Accumulator Welds sublect to Unanalyzed Thermal Transients Catawba 2 Inservlce Inspectlon Plan for Interval 2 Outage 7 Plan Report Page 42 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS H-01.001.001 2NI55-8 CN-2NI-55 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 160 0.719 50211 This weld examined under Item Number Class A Pipe to B09.011.077 in Outage 1(EOC8), and meets the Tee intent of this Elective Examination. This Elective Examination was added to the ISI Database per Engineering Examination Request # ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.002 2NI55-9 CN-2NI-55 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 140 1.000 50209 This Elective Examination was added to the ISI Class A Tee to Database per Engineering Examination Request #

Valve 2NI082 ER-CNS-99-01.

Depending on the examiner's qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.003 2NI55-10 CN-2NI-55 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 140 1.000 50209 This Elective Examination was added to the ISI Class A Tee to Database per Engineering Examination Request #

Valve 2NI081 ER-CNS-99-01.

Depending on the examiner's qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.004 2NI183-12 CN-2NI-183 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 160 0.719 50211 This Elective Examination was added to the ISI Class A Pipe to Database per Engineering Examination Request #

Tee ER-CNS-99-01.

EOC14 (

DUKE ENERk 4ORPORATION CATEGORY ELC, Elective Inspectlons INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report ENI Cold Lea Accumulator Welds sublect to MUnanalyzed Thermal Transients Catawba 2 InservIce Inspection Plan for Interval 2 Outage 7 Page 43 08//202006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUME3ERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS Depending on the examineres qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.005 2NI183-12L CN-2NI-183 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1.10.

Longitudinal NI CN-2562-1.1 160 0.719 50211 The examination includes at least a pipe diameter Class A Pipe to length but no more than 12 inches of longitudinal Tee weld intersecting the circumferential weld In reducing T, located near circumferential weld #12.

This Elective Examination was added to the ISI Database per Engineering Examination Request #

ER-CNS-99-01.

Depending on the examiner's qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.006 2NI183-17 CN-2NI-183 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 140 1.000 50209 This Elective Examination was added to the ISI Class A Valve 2NI093 to Database per Engineering Examination Request #

Tee ER-CNS-99-01.

Depending on the examiner's qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

H01.001.007 2NI183-17L CN-2NI-183 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Longitudinal NI CN-2562-1.1 140 1.000 50209 The examination includes at least a pipe diameter Class A Valve 2NI093 to length but no more than 12 Inches of longitudinal Tee weld intersecting the circumferential weld in reducing T, located near circumferential weld #17.

This Elective Examination was added to the ISI Database per Engineering Examination Request #

ER-CNS-99-01.

Depending on the examiner's qualifications,

EOC 14

(

CATEGORY ELC,. Elective Inspections DUKE ENER4% CORPORATION INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System INI Cold Leg Accumulator Welds sublect to Unanalyzed Thermal Transients Catawba 2 Inservice Inspection Plan for Interval 2 Outage 7 Plan Report Page 44 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUME3ERS PROC INSP REQ MATISCH DIA/THK CAL BLOCKS COMMENTS Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H-01.001.008 2NI183-18 CN-2NI-183 NDE-600 UT SS 10.000

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 140 1.000 50209 This Elective Examination was added to the ISI Class A Tee to Database per Engineering Examination Request #

Valve 2NI094 ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.009 2NI183-18L CN-2NI-183 NDE-600 UT SS 10.000

• Reference General Requirements Section 8.1.10.

Longitudinal NI CN-2562-1.1 140 1.000 50209 The examination includes at least a pipe diameter Class A Tee to length but no more than 12 inches of longitudinal Valve 2NI094 weld intersecting the circumferential weld in reducing T, located near circumferential weld #18.

This Elective Examination was added to the ISI Database per Engineering Examination Request #

ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.010 2NI184-12 CN-2NI-184 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 140 1.000 50209 This Elective Examination was added to the ISI Class A Valve 2NI059 to Database per Engineering Examination Request #

Tee ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 DUKE ENER&v CORPORATION C CATEGORY ELC, Elective Inspections INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System INI Cold Leg Accumulator Welds sublect to Unanalyzed Thermal Transients Catawba 2 Inservice Inspection Plan for Interval 2 Outage 7 Plan Report Page 45 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIANTHK CAL BLOCKS COMMENTS H01.001.011 2NI184-13 CN-2NI-184 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 140 1.000 50209 This Elective Examination was added to the ISI Class A Tee to Database per Engineering Examination Request #

Pipe ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

H01.001.012 2NI184-14 CN-2NI-184 NDE-600 UT SS 6.000

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 160 0.719 50211 This Elective Examination was added to the ISI Class A Tee to Database per Engineering Examination Request #

Pipe ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.013 2NI185-9 CN-2NI-185 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 140 1.000 50209 This Elective Examination was added to the ISI Class A Valve 2NI070 to Database per Engineering Examination Request #

Tee ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H-01.001.014 2NI185-9L CN-2NI-185 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Longitudinal NI CN-2562-1.1 140 1.000 50209 The examination includes at least a pipe diameter Class A Valve 2NI070 to length but no more than 12 inches of longitudinal Tee weld Intersecting the circumferential weld in reducing T, located near circumferential weld #9.

This Elective Examination was added to the ISI Database per Engineering Examination Request #

ER-CNS-99-01.

EOC 14 (

DUKE ENER*t CORPORATION C

CATEGORY ELC, Elective Inspections INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 46 Inservlce Inspection Plan for Interval 2 Outage 7 06/2012006 MIL!aalg Thermal Transients ITEM NUMBER IDNUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DINTHK CAL BLOCKS COMMENTS Depending on the examiner's qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 Is used, Calibration Block PDI-UT-2-C may be used.

H01.001.015 2NI185-10 CN-2NIo185 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 140 1.000 50209 This Elective Examination was added to the ISI Class A Tee to Database per Engineering Examination Request #

Valve 2NI071 ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used In lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.016 2NI185-10L CN-2NI-185 NDE-600 UT SS 10.000 *

• Reference General Requirements Section 8.1.10.

Longitudinal NI CN-2562-1.1 140 1.000 50209 The examination Includes at least a pipe diameter Class A Tee to length but no more than 12 inches of longitudinal Valve 2NI071 weld intersecting the circumferential weld in reducing T, located near circumferential weld #10.

This Elective Examination was added to the ISI Database per Engineering Examination Request #

ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

H01.001.017 2NI185-11 CN-2NI-185 NDE-600 UT SS 6.000

• Reference General Requirements Section 8.1.10.

Circumferential NI CN-2562-1.1 160 0.719 50211 This Elective Examination was added to the ISI Class A Tee to Database per Engineering Examination Request #

Pipe ER-CNS-99-01.

Depending on the examiners qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

EOC 14 ( C DUKE ENERr,, CORPORATION CATEGORY ELC, Elective Inspections INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report INI Cold Leg Accumulator Welds sublect to Catawba 2 Page 47 MUnanalyzed Thermal Transients Inservice Inspection Plan for Interval 2 Outage 7 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MATISCH DIAITHK CAL BLOCKS COMMENTS H01.001.018 2NI185-11L CN-2NI-185 NDE-600 UT SS 6.000 *

• Reference General Requirements Section 8.1 .10.

Longitudinal NI CN-2562-1.1 160 0.719 50211 The examination includes at least a pipe diameter Class A Tee to length but no more than 12 inches of longitudinal Pipe weld Intersecting the circumferential weld in reducing T. located near circumferential weld #11.

This Elective Examination was added to the ISI Database per Engineering Examination Request #

ER-CNS-99-01.

Depending on the examiner's qualifications, Procedure PDI-UT-2 may be used in lieu of NDE-600.

If PDI-UT-2 is used, Calibration Block PDI-UT-2-C may be used.

Total H01.001 Items: 18 Total H01 Items: 18

4.0 Results Of Inspections Performed The results of each examination shown in the final Inservice Inspection Plan (Section 3.0 of this report) are included in this section. The completion date and status for each examination are shown. All examinations revealing reportable indications and any corrective action required as a result are described in further detail in Subsections 4.1 and 4.2. Corrective measures performed and limited examinations are described in further detail in Subsections 4.3 and 4.4.

The information shown below is a field description for the reporting format included in this section of the report.

ITEM NUMBER = ASME Section Xl Tables IWB-2500-1 (Class 1), IWC-2500-1 (Class 2), IWF-2500-1 (Class 1 and Class 2),

Augmented / Elective Requirements ID NUMBER = Unique Identification Number SYSTEM = Component System Identification INSP DATE = Date of Examination INSP STATUS = CLR Clear REC Recordable REP Reportable INSP LIMITED = Indicates inspection was limited.

Coverage obtained is listed.

GEO REF = Y Yes (Geometric Reflector NNo applies only to UT)

= Y Yes RFR (Relief Request)

-- No COMMENTS = General and / or Detail Description EOC 14 Refueling Outage Report Page 1 of 2 Catawba Unit 2 Revision 0 Section 4 June 20, 2006

4.1 Reportable Indications None 4.2 Corrective Action Corrective action is action taken to resolve flaws and relevant conditions, including supplemental examinations, analytical evaluations, repair/

replacement activities, and corrective measures.

4.3 Corrective Measures Corrective measures are actions (such as maintenance) taken to resolve relevant conditions, but not including supplemental examinations, analytical evaluations, and repair / replacement activities. Any corrective measures performed for examinations associated with this report period will be shown on the examination data sheets which are on file at the Duke Energy Corporate Office in Charlotte, North Carolina.

4.4 Limited Examinations Limitations (i.e. 90% or less of the required examination coverage obtained) identified for examinations associated with this report period are shown below. A relief request will be submitted to seek NRC acceptance of the limited coverage. This information will be on file at The Duke Energy Corporate Office in Charlotte, North Carolina. Reference Subsection 1.3 for additional information.

Item Number Relief Request Serial Numbers B 12.040.002B To be filed later C05.011.077 To be filed later EOC 14 Refueling Outage Report Page 2 of 2 Catawba Unit 2 Revision 0 Section 4 June 20, 2006

DUKE ENERGY CORPORATION QUALITY ASSURANC( ICHNICAL SERVICES C Run D In-Service Inspection Datauase Management System EOC 14 Page 1 Catawba 2 Inservice Inspection Usting Plant: Catawba 2 Interval 2 Outage 7 07/11/2006 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS B05.010.001 B 2RPV-201-121BSE NC 03/29/2006 CLR - N N B05.010.002B 2RPV-201-121ASE NC 03/29/2006 CLR --- N N B05.010.003B 2RPV-201-121DSE NC 03/29/2006 CLR -- N N B05.010.004B 2RPV-201-121CSE NC 03/29/2006 CLR --- N N B05.130.004B 2NC1 1-08 NC 03/29/2006 CLR --- N N B05.130.008B 2NC9-08 NC 03/29/2006 CLR -- N N 605.130.0122B 2NC15-08 NC 03/29/2006 CLR --- N N 605.130.016B 2NC13-08 NC 03/29/2006 CLR --- N N B09.011.006 2NC1 19-4 NC 04/03/2006 CLR -- N N B09.011.006A 2NC1 19-4 NC 04/03/2006 CLR -- N N B09.011.007 2NC48-5 NC 03/25/2006 CLR -- N N 609.011.007A 2NC48-5 NC 03/25/2006 CLR --- N N B09.011.020 2NC255-1 NC 04/02/2006, CLR 91.20% N N 609.011.020A 2NC255-1 NC 04/02/2006 CLR --- N N B09.011.021 2NC255-3 NC 04/02/2006 CLR 91.20% N N B09.011.021A 2NC255-3 NC 04/02/2006 CLR --- N N B09.011.022 2NC255-4 NC 04/02/2006 CLR 91.20% N N B09.011.022A 2NC255-4 NC 04/02/2006 CLR -- N N B09.011.023 2NC257-1 NC 04/02/2006 CLR -- N N 609.011.023A 2NC257-1 NC 04/02/2006 CLR --- N N B09.011.067 2NI379-5 NI 03/24/2006 CLR -- N N B09.011.067A 2NI379-5 NI 03/24/2006 CLR --- N N B09.011.068 2NI379-8 NI 03/24/2006 CLR -- N N 809.011.068A 2NI379-8 NI 03/24/2006 CLR -- N N B09.011.069 2NI396-2 NI 04/07/2006 CLR --- N N B09.011.069A 2NI396-2 NI 04/07/2006 CLR --- N N B09.011.070 2NI396-4 NI 04/07/2006 CLR --- N N B09.011.070A 2NI396-4 NI 04/07/2006 CLR -- N N B09.011.099 2NC1 12-4 NC 04/03/2006 CLR - N N B09.011.099A 2NC112-4 NC 04/03/2006 CLR - N N B09.021.007 2NC140-4 NC 03/25/2006 CLR -- N N 609.021.008 2NC140-5 NC 03/25/2006 CLR --- N N B09.021.009 2NC145-5 NC 03/23/2006 CLR -- N N B09.021.010 2NC146-6 NC 03/25/2006 CLR - N N B09.021.027 2NC74-16 NC 03/25/2006 CLR -- N N B09.031.001 2NC11-WN7 NC 03/31/2006 CLR -- N N B09.031.002 2NC11-WN8 NC 03/31/2006 CLR --- N N

DUKE ENERGY CORPORATION EOC 14 C QUALITY ASSURANC' 'iCHNICAL SERVICES In-Service Inspection Da .jase Management System Run D Page 2 Catawba 2 Inservice Inspection Listing Plant: Catawba 2 711/2006 07A Interval 2 Outage 7 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS B09.040.007 2NC53-36 NC 03/23/2006 CLR - N N B09.040.008 2NC53-37 NC 03/23/2006 CLR -- N N B09.040.013 2NC89-20 NC 03/29/2006 CLR --- N N B09.040.014 2NC89-21 NC 03/29/2006 CLR - N N B09.040.015 2NC89-4 NC 03/29/2006 CLR -- N N B09.040.016 2NC89-7 NC 03/31/2006 CLR --- N N B09.040.017 2NC89-12 NC 03/29/2006 CLR --- N N B09.040.018 2NC89-13 NC 03/29/2006 CLR --- N N B09.040.030 2NI306-4 NI 03/24/2006 CLR -- N N B09.040.031 2NI306-6 NI 03/24/2006 CLR -- N N 109.040.032 2NI322-2 NI 03/24/2006 CLR -- N N B09.040.033 2NI322-4 NI 03/24/2006 CLR --- N N B09.040.034 2NI396-13 NI 03/24/2006 CLR --- N N B09.040.035 2NI396-18 NI 03/24/2006 CLR -- N N B09.040.036 2NI396-20 NI 03/24/2006 CLR --- N N B09.040.037 2NI396-21 NI 04/07/2006 CLR - N N 812.040.002B 2ND-37A ND 04/01/2006 CLR 70.80% N Y Request for Relief will be filed C01.010.006 2SWRF-1-3 NV 03/08/2006 CLR 96.00% N N C01.020.001 2SGD-06B-07 NC 04/03/2006 CLR 99.70% N N C01.020.012 2ASWINJF-SH-HD NV 04/02/2006 CLR 70.00% N N Examined with Radioaraohv durina EOC1 4. per Duke Enerav Response to NRC Request for Additional Information, pertaining to Request for Relief Serial Number 04-CN-002, dated May 17, 2005.

C01.020.017 2SWRF-1-2 NV 03/08/2006 CLR N N C02.011.003 2SWRF-1-OUTLET NV 03/08/2006 CLR N N C02.021.003 2SGD-UH-15 NC 03/21/2006 CLR 97.60% N N C02.021.003A 2SGD-UH-15 NC 03/21/2006 CLR N N C03.020.001 2-R-CF-1521 CF 04/06/2006 CLR N N C03.020.004 2-R-CF-1582 CF 04/06/2006 CLR N N C03.020.005 2-R-CF-1563 CF 04/01/2006 CLR N N C03.020.01 0 2-R-CF-1585 CF 04/06/2006 CLR N N C03.020.054 2-R-NV-0281 NV 02/02/2005 CLR N N C03.040.001 2-R-SV-i573 SV 04/04/2006 CLR N N C03.040.002 2-R-SV-1574 SV 04/04/2006 CLR N N C03.040.003 2-R-SV-1553 SV 04/04/2006 CLR N N C03.040.004 2-R-SV-1554 SV 04/04/2006 CLR N N C03.040.005 2-R-SV-1610 SV 04/05/2006 CLR N N

DUKE ENERGY CORPORATION EOC 14

( QUALITY ASSURANC( "CHNICAL SERVICES In-Service Inspection Dataoase Management System

( Run D Page 3 Plant:OCat a 24 Catawba 2 Inservice Inspection Usting Page23 Plant: Catawba 2 Interval 2 Outage 7 07/11/2006 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS C03.040.006 2-R-SV-1 611 SV 04/05/2006 CLR -- N N C03.040.007 2-R-SV-1 593 SV 04/05/2006 CLR -- N N C03.040.008 2-R-SV-1 594 SV 04/05/2006 CLR -- N N C05.011.073 2ND24-2 ND 03/15/2006 CLR -- N N C05.011 .073A 2ND24-2 ND 03/15/2006 CLR --- N N C05.011.074 2ND24-4 ND 03/15/2006 CLR --- N N C05.011.074A 2ND24-4 ND 03/15/2006 CLR -- N N C05.011.075 2ND24-6 ND 03/15/2006 CLR -- N N C05.011.075A 2ND24-6 ND 03/15/2006 CLR --- N N C05.011.076 2ND24-8 ND 03/15/2006 CLR --- N N C05.011.076A 2ND24-8 ND 03/15/2006 CLR --- N N C05.011.077 2ND24-16 ND 03/15/2006 CLR 62.50% N Y Request for Relief will be filed.

C05.011.077A 2ND24-16 ND 03/15/2006 CLR --- N N C05.011.083 2ND46-6 ND 03/07/2006 CLR --- N N C05.011.083A 2ND46-6 ND 03/07/2006 CLR -- N N C05.011.114 2NI73-10 NI 03/27/2006 CLR - N N C05.011.114A 2NI73-10 NI 03/26/2006 CLR -- N N C05.011.115 2NI73-11 NI 03/27/2006 CLR --- N N C05.011.115A 2NI73-11 NI 03/26/2006 CLR --- N N C05.011.116 2NI73-2 NI 03/27/2006 CLR --- N N C05.011.116A 2NI73-2 NI 03/28/2006 CLR --- N ' N C05.011.117 2NI73-4 NI 03/27/2006 CLR --- N N C05.011.117A 2NI73-4 NI 03/26/2006 CLR --- N N C05.011.118 2NI76-2 NI 03/24/2006 CLR -- N N C05.011.118A 2NI76-2 NI 03/24/2006 CLR -- N N C05.011.119 2NI76-3 NI 03/24/2006 CLR -- N N C05.011.119A 2NI76-3 NI 03/24/2006 CLR --- N N C05.011.120 2NI76-4 NI 03/24/2006 CLR --- N N C05.011.120A 2NI76-4 NI 03/24/2006 CLR -- N N C05.011.121 2NI76-5 NI 03/24/2006 CLR --- Y N C05.011.121A 2NI76-5 NI 03/24/2006 CLR --- N N C05.011.149 2NI89-1 NI 03/28/2006 CLR - N N C05.011.149A 2NI89-1 NI 03/26/2006 CLR --- N N C05.011.150 2NI89-4 NI 03/28/2006 CLR - N N C05.011.150A 2NI89-4 NI 03/26/2006 CLR - N N C05.011.151 2NI89-5 NI 03/28/2006 CLR -- N N C05.011.151A 2NI89-5 NI 03/26/2006 CLR --- N N

DUKE ENERGY CORPORATION QUALITY ASSURANC( '.CHNICAL SERVICES In-Service Inspection Dathaase Management System

(: Run D EOC 14 Page 4 Catawba 2 Inservice Inspection Usting Plant: Catawba 2 Interval 2 Outage 7 07/11/2006 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS C05.011.152 2NI89-6 NI 03/28/2006 CLR N N C05.01 1.1 52A 2NI89-6 NI 03/26/2006 CLR C05.011.153 2NI89-7 NI 03/28/2006 CLR C05.011.153A 2NI89-7 NI 03/26/2006 CLR C05.011.154 2NI89-10 NI 03/28/2006 CLR C05.011.154A 2NI89-10 NI 03/26/2006 CLR C05.011.155 2NI89o- 1 NI 03/28/2006 CLR C05.011.155A 2NI89-11 NI 03/26/2006 CLR C05.011.160 2NI76-6 NI 03/24/2006 CLR C05.011.160A 2NI76-6 NI 03/24/2006 CLR C05.021.121 2NI303-1 NI 03/27/2006 CLR C05.021.121A 2NI303-1 NI 03/26/2006 CLR C05.021.122 2NI303-10 NI 03/27/2006 CLR C05.021.122A 2NI303-1 0 NI 03/26/2006 CLR C05.021.123 2NI303-13 NI 03/27/2006 CLR C05.021.123A 2NI303-13 NI 03/26/2006 CLR C05.021.124 2NI303-14 NI 03/27/2006 CLR C05.021.124A 2NI303-14 NI 03/26/2006 CLR C05.021.125 2NI309-10 NI 03/27/2006 CLR C05.021.125A 2NI309-1 0 NI 03/26/2006 CLR C05.021.126 2NI309-11 NI 03/27/2006 CLR C05.021.126A 2NI309-11 NI 03/26/2006 CLR C05.021.127 2NI369-19 NI 04/07/2006 CLR C05.021.127A 2NI369-19 NI 04/07/2006 CLR C05.021.128 2NI369-8 NI 03/25/2006 CLR C05.021.128A 2NI369-8 NI 03/25/2006 CLR C05.021.129 2NI68-2 NI 03/29/2006 CLR C05.021.129A 2NI68-2 NI 03/29/2006 CLR C05.021.130 2NI68-10 NI 03/29/2006 CLR C05.021.130A 2NI68-10 NI 03/29/2006 CLR C05.021.250 2NV47-17 NV 03/09/2006 CLR C05.021.250A 2NV47-17 NV 03/09/2006 CLR C05.021.251 2NV47-18 NV 03/09/2006 CLR C05.021.251A 2NV47-18 NV 03/09/2006 CLR C05.021.252 2NV47-9 NV 03/09/2006 CLR C05.021.252A 2NV47-9 NV 03/09/2006 CLR C05.021.253 2NV47-20 NV 03/09/2006 CLR

DUKE ENERGY CORPORATION QUALITY ASSURANC( ECHNICAL SERVICES ( Run D In-Service Inspection Datioase Management System EOC 14 Page 5 Catawba 2 Inservlce Inspection Listing Plant: Catawba 2 07/11/2006 Interval 2 Outage 7 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS C05.021.253A 2NV47-20 NV 03109/2006 CLR N C05.021.254 2NV489-12 NV 03/02/2006 CLR C05.021.254A 2NV489-12 NV 03/02/2006 CLR C05.021.255 2NV489-13 NV 03/02/2006 CLR C05.021.255A 2NV489-13 NV 03/02/2006 CLR C05.021.256 2NV49-8 NV 03/03/2006 CLR C05.021.256A 2NV49-8 NV 03/03/2006 CLR C05.021.257 2NV49-9 NV 03/03/2006 CLR C05.021.257A 2NV49-9 NV 03/03/2006 CLR C05.021.258 2NV50-15 NV 03/02/2006 CLR C05.021.258A 2NV50-15 NV 03/02/2006 CLR C05.021.259 2NV50-16 NV 03/02/2006 CLR C05.021.259A 2NV50-16 NV 03/02/2006 CLR C05.051.009 2CA93-1 CA 04/05/2006 CLR C05.051.009A 2CA93-1 CA 04/05/2006 CLR C05.051.011 2CA97-1 CA 04/04/2006 CLR C05.051.011 A 2CA97-1 CA 04/04/2006 CLR C05.051.103 2SM12-4 SM 04/04/2006 CLR C05.051.103A 2SM12-4 SM 04/04/2006 CLR C05.051.110 2SM-8A-B SM 04/10/2006 CLR C05.051.1 1OA 2SM-8A-B SM 04/10/2006 CLR C05.051.111 2SM-8A-F SM 04/09/2006 CLR C05.051.111A 2SM-8A-F SM 04/09/2006 CLR C05.051.153 2SV19-3 SV 04/07/2006 CLR C05.051.153A 2SV19-3 SV 04/07/2006 CLR C05.081.001 2SM-5A-C SM 04/10/2006 CLR C06.020.016 2SA-1 SA 04/02/2006 CLR C06.020.018 2SV-10 SV 04/02/2006 CLR C06.020.019 2SV-14 SV 04/02/2006 CLR C06.020.020 2SV-20 SV 04/01/2006 CLR D02.020.001 2-R-CA-0142 CA 10/17/2005 CLR D02.020.007 2-R-KC-0313 KC 10/17/2005 CLR D02.020.014 2-R-RN-0226 RN 11/08/2005 CLR D02.020.015 2-R-RN-0239 RN 10/17/2005 CLR D02.020.018 2-RNPB-SUPPORT RN 03/23/2006 CLR F01.010.003 2-R-NC-2002 NC 03/21/2006 CLR F01.010.004 2-R-NC-2005 NC 03/21/2006 CLR

DUKE ENERGY CORPORATION QUALITY ASSURANQ "ECHNICAL SERVICES Run D In-Service Inspection Daljaese Management System Page 6 EOC 14 Catawba 2 Inservice Inspection Listing Plant: Catawba 2 07/11/2006 Interval 2 Outage 7 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS F01.010.007 2-R-NC-1501 NC 03/20/2005 CLR F01.012.013 2-R-NC-1693 NC 02/23/2006 CLR F01.020.039 2-R-ND-0140 ND 10/17/2005 CLR F01.020.040 2-R-ND-0141 ND 10/24/2005 CLR F01.020.041 2-R-ND-0246 ND 10/24/2005 CLR F01.020.042 2-R-ND-0247 ND 11/01/2005 CLR F01.020.043 2-R-ND-0248 ND 11/01/2005 CLR F01.020.044 2-R-ND-0318 ND 11/01/2005 CLR F01.020.074 2-R-NI-0040 NI 10/17/2005 CLR F01.020.075 2-R-NI-0045 NI 10/17/2005 CLR F01.020.076 2-R-NI-0047 NI 10/18/2005 CLR F01.020.077 2-R-NI-0048 NI 10/17/2005 CLR F01.020.106 2-R-NS-1011 NS 03t22/2006 CLR F01.020.107 2-R-NS-1018 NS 03/20/2006 CLR F01.020.108 2-R-NS-1019 NS 03/20/2006 CLR F01.020.162 2-R-NV-0006 NV 10/18/2005 CLR F01.020.163 2-R-NV-0007 NV 10/18/2005 CLR F01.020.164 2-R-NV-0252 NV 10/18/2005 CLR F01.020.165 2-R-NV-0254 NV 10/18/2005 CLR F01.020.166 2-R-NV-0255 NV 10/18/2005 CLR F01.020.223 2-R-SV-1589 SV 03/20/2006 CLR F01.020.224 2-R-SV-1591 SV 03/20/2006 CLR F01.021.035 2-R-ND-0322 ND 11/01/2005 CLR F01.021.078 2-R-NI-1783 NI 03/21/2006 CLR F01.021.079 2-R-NI-1785 NI 03/21/2006 CLR F01.021.080 2-R-NI-1786 NI 03/21/2006 CLR F01.021.104 2-R-NS-0063 NS 10/17/2005 CLR F01.021.105 2-R-NS-0068 NS 10/18/2005 CLR F01.021.162 2-R-NV-0251 NV 10/18/2005 CLR F01.021.163 2-R-NV-0253 NV 10/18/2005 CLR F01.021.164 2-R-NV-0289 NV 11/01/2005 CLR F01.021.165 2-R-NV-0290 NV 11/01/2005 CLR F01.030.072 2-R-KC-0313 KC 10/17/2005 CLR F01.030.122 2-R-LD-0016 LD 03/08/2006 CLR F01.031.015 2-R-CA-0142 CA 10/17/2005 CLR F01.031.057 2-R-KC-0252 KC 11/02/2005 CLR F01.031.058 2-R-KC-0253 KC 11/02/2005 CLR

DUKE ENERG/Y CORPORATION EOC 14 C QUALITY ASSURANO* ECHNICAL SERVICES In-Service Inspection Database Management System

( Run D Catawba 2 Inservlce Inspection Usting Page 7 Plant: Catawba 2 Interval 2 Outage 7 07/11/2006 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS F01.031.059 2-R-KC-0347 KC 11/0212005 CLR - N N F01.031.060 2-R-KC-0218 KC 11/02/2005 CLR - N N F01.031.061 2-R-KC-0219 KC 11/02/2005 CLR .-- N N F01.031.062 2-R-KC-0221 KC 11/02/2005 CLR --- N N F01.031.153 2-R-RN-0226 RN 11/08/2005 CLR --- N N F01.031.154 2-R-RN-0239 RN 10/17/2005 CLR --- N N F01.032.104 2-R-KD-0033 KD 10/17/2005 CLR --- N N F01.032.105 2-R-KD-0007 KD 10/19/2005 CLR - N N F01.032.153 2-R-RN-0037 RN 10/17/2005 CLR .-- N N F01.040.101 2SGA-SUPPORT NC 04/06/2006 REC --- N N F01.040.103 2REGHX-SUPPORT 04/08/2006 CLR --- N N F01.040.109 2SWRF-SUPPORT NV 03/08/2006 CLR -- N N F01.040.110 2CCPA-SUPPORT 10/25/2005 CLR --- N N F01.040.219 2RNPB-SUPPORT RN 03/23/2006 CLR -- N N F01.040.220 2RNSB-SUPPORT RN 03/23/2006 CLR -- N N H01.001.001 2NI55-8 NI 03/23/2006 CLR .-- N N H01.001.002 2NI55-9 NI 03/23/2006 CLR --- N N H01.001.003 2NI55-10 NI 03/28/2006 CLR -- N N H01.001.004 2NI183-12 NI 03/28/2006 CLR -- Y N H01.001.005 2NI183-12L NI 03/28/2006 CLR .-- N N H01.001.006 2NI183-17 NI 03/28/2006 CLR .-- N N H01.001.007 2NI183-17L NI 03/28/2006 CLR --- N N H01.001.008 2NI183-18 NI 03/28/2006 CLR -- Y N H01.001.009 2NI183-18L NI 03/28/2006 CLR -- N N H01.001.010 2N1184-12 NI 03/28/2006 CLR N N H01.001.011 2N1184-13 NI 03/28/2006 CLR .-. N N H01.001.012 2N1184-14 NI 03/28/2006 CLR -- N N H01.001.013 2N1185-9 NI 03/28/2006 CLR --- N N H01.001.014 2NI185-9L NI 03/28/2006 CLR -- N N H01.001.015 2N1185-10 NI 03/28/2006 CLR -- N N H01.001.016 2NI185-10L NI 03/28/2006 CLR --- N N H01.001.017 2N1185-11 NI 03/28/2006 CLR ... N N H01.001.018 2NI185-11L NI 03/28/2006 CLR - N N

5.0 Owner's Report for Repair I Replacement Activities As required by the applicable code, records of Class 1 and Class 2 Repair and Replacement work is included on NIS-2 forms in this section.

The NIS-2 forms included in this section were completed for work performed during this report period.

The individual work request documents and manufacturers' data reports are on file at Catawba Nuclear Station.

EOC 14 Refueling Outage Report Page I of 1 Catawba Unit 2 Revision 0 Section 5 June 20,2006

( (- (

Flaw Indication Code Repair, Maint/ ISI Owner Work Order Class Sys MOD No. Description of Work Replacement (*Yes No) Final ANII Final 98630140-01 A NI NA Valve Disc for 2NI-71 Replacement No 2/9/2005 2/14/2005 98520607-06 B NI NA Valve Disc for 2N1-102 Replacement No 2/14/2005 2/15/2005 98674876-01 B NS NA NS Pump "2B" Bolting Replacement No 3/8/2005 3/8/2005

( C (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owner DUKE POWER COMPANY la Date 3/08/05 Sheet / of /

Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Plant CATAWBA NUCLEAR STATION 2a Unit I'I 1 02 El 3 ["1 Shared (specify Units" )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98674876-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NS CONTAINMENT SPRAY SYSTEM Class B

5. (a) Applicable Construction Code 1IT 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1989 Addenda NONE 6_ Identifieation of Crnmnnnent.* Renaired or Renlaeement Comnonent.*

Column 1 Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Bolting Duke Power NA NA Bolting- SA193 Gr. B7 Hex Nuts- NA Replaced No Co. SA194 Gr 2H for NS Pump "2B" B Bolting Duke Power NA NA Bolting- SA564 Tp 630 H1 100 for NS NA Replacement No Co. Pump "2B" C-E-

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Bolting for NS Pump "2B"-

8. Test Conducted: Hydrostatic El Pneumatic D] Nominal Operating Pressure "] Other[] Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases __NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A TECH SPEC Date _,204._:

Signed..

Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of NORTH CAROLINA and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 2.-2J - OS to 3 " 5 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_ __**_ _._ _ _ _Commissions NC 978 In'pector's Signature Date 3* & ,200 5 _

Revision 6

(i C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owner DUKE POWER COMPANY la Date 02/09/05 Sheet of Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Plant CATAWBA NUCLEAR STATION 2a Unit -' 1 [2 D-3 E] Shared (specify Units[] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98630140-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NI SAFETY INJECTION SYSTEM Class A

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases_

(b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1989 Addenda NONE

6. Identification of Com nonents Renaired or Renlacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufactur N B Other Identification (Size) Year Repaired. ASME Component Manufacturer er Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Disc Assembly Westinghouse S-74 NA For Valve 2NI-71 1977 Replaced No B Disc Assembly Westinghouse RP 1003 NA For Valve 2NI-71 2000 Replacement No c

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2)

/ information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbished Valve 2NI-7 I_

8. Test Conducted: Hydrostatic LI Pneumatic E" Nominal Operating Pressure I'] Other [] Exempt Z Pressure psig Test Temp, deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of uthorization No. N/A Signed /2 )4 2 TECH SPEC Date ,20,_S" S Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of NORTH CAROLINA and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 9 -19 .01 to 2-- A- 0-. and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_________________Commissions NC 978 Inspettor's Signature Date ,- V\ý ,2 0_b3-- _

Revision 6

( C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owner DUKE POWER COMPANY 1a Date 2/14/05 Sheet of Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Plant CATAWBA NUCLEAR STATION 2a Unit E" 1 Z2 El 3 [-] Shared (specify Units[] )

Addrc*s 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98520607-06 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NI SAFETY INJECTION SYSTEM Class B

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1989 Addenda NONE

6. Identification of Components Repaired or Replacement Components Column 1 Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number

_ _(Ms or no)

A Disc Dresser NA NA Valve tag 2NI-102 NA Replaced No B Disc Dresser A14134 H22 NA Valve tag 2NI-102 NA Replacement No C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2)

• .-' information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbished Valve 2NI-102_

8. Test Conducted: Hydrostatic L-I Pneumatic [:] Nominal Operating Pressure EI OtherE-Exempt 2 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed AASW3Z TECH SPEC Date -.206S-"

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of NORTH CAROLINA and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 7--.-S- to t.. oS -O and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

& A n'7a* Commissions NC 978 Inspecto"'s Signature Date _2.- S_ 20_0-S Revision 6

6.0 Pressure Testin, Table 6-1 shows the number of ISI Class 1 (Category B-P) and ISI Class 2 (Category C-H) pressure tests completed for refueling cycle 2EOC14.

Table 6-1 Outage Specific Summary Examination Category Test Requirement Total Completed2EOC14 B-P System Leakage Test (IWB-5221) 1 C-H System Hydrostatic Test (IWC-5222) 14 Section 6 Prepared By: Date:

619 1 Z&e6 Section 6 Reviewed By: Date:

Refueling Outage Report 2EOC14 Page 1 of 5 S Catawba Unit 2 Revision 0 2nd 10-Year Interval May 9, 2006 Section 6

Table 6-2 shows a completion status of pressure tests conducted during the third period of the second ten-year interval.

Table 6-2 Period Specific Summarv Total Total (%)

Examination Test Requirement Examinations Examinations Examinations Category RequiredFor CreditedFor Complete For This Period This Period This Period B-E System Hydrostatic 1 1 100%

Test (IWB-5222)

B-P System Leakage Test 1 1 100%

(IWB-5221)

B-P System Hydrostatic 12 12 100%

Test (IWB-5222)

C-H System 0 0 0%

Inservice/Functional Test (IWC-5221)

C-H System Hydrostatic 321 32 100%

Test (IWC-5222)

I The total number required changed from 33 in the last summary report to 32 because one zone was deleted per plan addendum C2-PT-02 1.

, Refueling Outage Report 2EOC14 Page 2 of 5 Catawba Unit 2 Revision 0 2nd 10-Year Interval May 9, 2006 Section 6

Table 6-3 shows a completion status of the 1 - Class 1 (Category B-P) pressure test zone conducted during refueling cycle 2EOC14.

Table 6-3 Detailed Class I Listing 2EOC14 2EOC14 VT-2 Zone Completion Examination Number Boundary Dwg Status Test Type Date 2NC-001 L-A CN-ISIL-2553-1.0 Complete Leakage 04/17/06 CN-ISIL-2553-1.1 Complete Leakage 04/17/06 CN-ISIL-2554-1.0 Complete Leakage 04/17/06 CN-ISIL-2554-1.5 Complete Leakage 04/17/06 CN-ISIL-2561-1.0 Complete Leakage 04/17/06 CN-ISIL-2561-1.1 Complete Leakage 04/17/06 CN-ISIL-2562-1.0 Complete Leakage 04/17/06 CN-ISIL-2562-1.1 Complete Leakage 04/17/06 CN-ISIL-2562-1.2 Complete Leakage 04/17/06 CN-ISIL-2562-1.3 Complete Leakage 04/17/06 Refueling Outage Report 2EOC1 4 Page 3 of 5 Catawba Unit 2 Revision 0 2nd 10-Year Interval May 9, 2006 Section 6

Table 6-4 shows a completion status of the 14 - Class 2 (Category C-H) hydrostatic

• .- pressure test zones completed during refueling cycle 2EOC14.

Table 6-4 Detailed Class 2 Listina 2EOC14 2EOC14 VT-2 Zone Completion Examination Number Boundary Dwg Status Test Type Date 1 2FW-001 H-B CN-ISIH-2554-1.2 Complete Hydrostatic 07/11/05 CN-ISIH-2554-1 .7 Complete Hydrostatic 07/11/05 CN-ISIH-2561 -1.0 Complete Hydrostatic 07/11/05 CN-ISIH-2562-1.2 Complete Hydrostatic 07/11/05 CN-ISIH-2563-1.0 Complete Hydrostatic 07/11/05 CN-ISIH-2570-1.0 Complete Hydrostatic 07/11/05 CN-ISIH-2571-1.0 Complete Hydrostatic 07/11/05 CN-ISIH-2571 -1.0 Complete Hydrostatic 07/13/05 2 2KF-001 H-B CN-ISIH-2570-1.0 Complete Hydrostatic 09/08/05 3 2NI-003H-B CN-ISIH-2562-1.2 Complete Hydrostatic 04/07/06 CN-ISIH-2562-1.3 Complete Hydrostatic 04/07/06 4 2NI-005H-B CN-ISIH-2562-1.2 Complete Hydrostatic 11/30/05 5 2NI-009H-B CN-ISIH-2562-1.2 Complete Hydrostatic 04/14/06 6 2NS-001 H-B CN-ISIH-2563-1.0 Complete Hydrostatic 08/04/05 7 2NS-002H-B CN-ISIH-2563-1.0 Complete Hydrostatic 08/11/05 8 2NS-003H-B CN-ISIH-2563-1.0 Complete Hydrostatic 208/17/98 9 2NV-002H-B CN-ISIH-2554-1.7 Complete Hydrostatic* 07/05/05 10 2NV-003H-B CN-ISIH-2554-1.7 Complete Hydrostatic 07/18/05 11 2NV-004H-B CN-ISIH-2554-1.2 Complete Hydrostatic 03/08/06 12 2NV-005H-B CN-ISIH-2554-1.2 Complete Hydrostatic 02/28/06 13 2NV-006H-B CN-ISIH-1554-1.4 Complete Hydrostatic 11/02/05 CN-ISIH-1 556-1.0 Complete Hydrostatic 11/02/05 CN-ISIH-2554-1.0 Complete Hydrostatic 11/02/05 CN-ISIH-2554-1.1 Complete Hydrostatic 11/02/05 2 A test was performed to satisfy the requirements of IWC-5222(d) during the first inspection period as allowed by Table IWC-2500-1, Category C-H, footnote 8.

Refueling Outage Report 2EOC14 Page 4 of 5 S Catawba Unit 2 Revision 0 2nd 10-Year Interval May 9, 2006 Section 6

Table 6-4 DetailedClass 2 Listinct 2EOC14 2EOC14 VT-2 Zone Completion Examination Number Boundary Dwg Status Test Type Date 13 2NV-006H-B CN-ISIH-2554-1.2 Complete Hydrostatic 11/02/05 CN-ISIH-2554-1.5 Complete Hydrostatic 11/02/05 CN-ISIH-2554-1.6 Complete Hydrostatic 11/02/05 CN-ISIH-2554-1.7 Complete Hydrostatic 11/02/05 CN-ISIH-2562-1.0 Complete Hydrostatic 11/02/05 CN-ISIH-2562-1.2 Complete Hydrostatic 11/02/05 I I I +

14 1 2SA-001 H-B CN-ISIH-2593-1 .1 Complete Hydrostatic 09/07/05 Refueling Outage Report 2EOC14 Page 5 of 5

"-.- Catawba Unit 2 Revision 0 2nd 10-Year Interval May 9, 2006 Section 6

Attachment 2 Inservice Inspection Report Catawba Unit 2 2006 Refueling Outage EOC14 (Outage 1)

Third Inservice Inspection Interval

FORM NIS-1 OWNER'S REPORT FOR INSERVICE INSPECTIONS As required by the Provisions of the ASME Code Rules

1. Owner: Duke Enerqy, 526 S. Church St., Charlotte, NC 28201-1006 (Name and Address of Owner)

2. Plant: Catawba Nuclear Station, 4800 Concord Road, York, SC 29745 (Name and Address of Plant)

3. Plant Unit: 2 4. Owner Certificate of Authorization (if required): N/A

5. Commercial Service Date: 8/19/86 6. National Board Number for Unit: 173

7. Components Inspected:

Component or Manufacturer Manufacturer State or National Appurtenance Installer Installer Serial Province No. Board No.

No.

See Section 1.1 in the Attached Report Note: Supplemental sheets in the form of lists, sketches, or drawings may be used provided (1) size is 81/2 in.

x 11 in., (2) information in items 1 through 6 on this report is included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

Total number of pages contained in this report 182

FORM NIS-i (Back)

'. Examination Dates: October 15, 2005 to April 24, 2006

9. Inspection Period Identification: First Period

10. Inspection Interval Identification: Third Interval

11. Applicable Edition of Section XI: 1998 Addenda 2000

12. Date / Revision of Inspection Plan: March 1, 2006 / Revision 0

13. Abstract of Examinations and Tests. Include a list of examinations and tests and a statement concerning status of work required for the Inspection Plan: See Sections 2.0, 3.0 and 6.0

14. Abstract of Results of Examinations and Tests: See Section 4.0 and 6.0

15. Abstract of Corrective Measures: See Subsection 4.3 We certify that a) the statements made in this report are correct, b) the examinations and tests meet the Inspection Plan as required by the ASME Code,Section XI, and c) corrective measures taken conform to the rules of the ASME Code,Section XI.

Certificate of Authorization No. (if applicable) N/A Expiration Date N/A Date 14n,7 7_mW,, Signed Duke Ener gy By _ _ _

w

• dr Owner /

-q CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of Nit employed by

• HSB of Connecticut have inspected the components described in this Owner's Report during the period 10 - I .. - 00 to

" - I A - -& , and state that to the best of my knowledge and belief, the Owner has performed examinations and tests and taken corrective measures described in this Owner's Report in accordance with the Inspection Plan and as required by the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations, tests, and corrective measures described in this Owner's Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage orany kind arising from or connected with this inspection Commissions A) C f 1lilspector's Signature National Board, State, Province, and Endorsements Date "- iAA2(Z

• The Hartford Steam Boiler Inspection & Insurance Company of Connecticut 200 Ashford Center North Suite 205 Atlanta, GA. 30338-4860

, (800) 417-3721 www.hsbct.com

INSERVICE INSPECTION REPORT CA TAWBA - UNIT 2 2006 REFUELING OUTAGE EOC14 (OUTAGE 1)

Location: 4800 Concord Road, York, South Carolina 29745 NRC Docket No. 50-414 National Board No. 173 Commercial Service Date: August 19, 1986 Owner: Duke Energy Corporation 526 South Church St.

Charlotte, N.C. 28201-1006 Revision 0 Prepared By: Date Reviewed By: Date 74-0 Approved By: Date

DISTRIBUTION LIST

1. Duke Energy Quality Assurance Technical Services (QATS)(Original)

2. NRC Document Control Desk

TABLE OF CONTENTS Section Title Revision 1.0 General Information 0 2.0 Second Ten-Year Interval Inspection Status 0 3.0 Final Inservice Inspection Plan 0 4.0 Results of Inspections Performed 0 5.0 Owner's Report for Repair / Replacement Activities 0 6.0 Pressure Testing 0

,I .0 General Information This report describes the Inservice Inspection of Duke Energy's Catawba Nuclear Station Unit 2 during Outage 1 / EOC14. This is the First Outage of the First Inspection Period of the Third Ten-Year Interval. By letter dated October 25, 2005 to the U.S.

Nuclear Regulatory Commission, Duke Energy cited their intent to utilize ASME Interpretation, #1N05-09, that allows Duke Energy to start the Catawba Unit 2, 3r inspection interval prior to completing the 2 nd inspection interval. ASME Section XI, 1998 Edition with 2000 Addenda, was the governing Code for selection and performance of the ISI examinations.

Included in this report are the inspection status for each examination category, the final inservice inspection plan, the inspection results for each item examined, and corrective actions taken when reportable conditions were found. In addition, there is an Owner's Report for Repair / Replacement Section included for completed NIS-2 documentation of repairs and replacements.

1.1 Identification Numbers Manufacturer Manufacturer State or National Item or Installer or Installer Province No. Board Serial No. No.

Reactor Vessel Combustion 8871 N/A 21667 Engineering Pressurizer Westinghouse 1931 N/A W26949 Steam Generator 2A Westinghouse 1923 N/A 4 Steam Generator 2B Westinghouse 1922 N/A 3 Steam Generator 2C Westinghouse 1921 N/A 2 Steam Generator 2D Westinghouse 1924 N/A 5 Reactor Coolant Pump 2A Ionics, Inc. 1S-86P765 N/A 342 Reactor Coolant Pump 2B Ionics, Inc. 2S-86P765 N/A 343 EOC 14 Refueling Outage Report Page 1 of 5 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

1.1 Identification Numbers (Continued)

Manufacturer Manufacturer State or National Item or Installer or Installer Province Board No.

Serial No. No.

Reactor Coolant Pump 2C Ionics, Inc. 3S-86P765 N/A 586 Reactor Coolant Pump 2D Ionics, Inc. 4S-86P765 N/A 587 Reactor Coolant System Duke Power Co. C-2NC N/A 171 Safety Injection System Duke Power Co. C-2NI N/A 172 Residual Heat Removal Duke Power Co. C-2ND N/A 154 System Chemical and Volume Duke Power Co. C-2NV N/A 170 Control System Auxiliary Feedwater Duke Power Co. C-2CA N/A 159 System Feedwater System Duke Power Co. C-2CF N/A 158 Refueling Water System Duke Power Co. C-2FW' N/A 141 Main Steam Supply to Duke Power Co. C-2SA N/A 134 Auxiliary Equipment Main Steam System Duke Power Co. C-2SM N/A 162 Main Steam Vent to Duke Power Co. C-2SV N/A 156 Atmosphere System Containment Spray System Duke Power Co. C-2NS N/A 150 Steam Generator Duke Power Co. C-2BB N/A 155 Blowdown System Steam Generator Wet Duke Power Co. C-2BW N/A 152 Layup Recirculation System EOC 14 Refueling Outage Report Page 2 of 5 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

1.1 Identification Numbers (Continued)

Manufacturer Manufacturer State or National Item or Installer or Installer Province No. Board No.

Serial No.

Spent Fuel Cooling Duke Power Co. C-2KF N/A 151 System Boron Recycle System Duke Power Co. C-2NB N/A 153 Nuclear Sampling Duke Power Co. C-2NM N/A 169 System Containment Duke Power Co. C-2NW N/A 165 Penetration Valve Injection Water System Liquid Radwaste Duke Power Co. C-2WL N/A 168 System Excess Letdown Heat Atlas Industrial 3205 N/A 2583 Exchanger Manufacturing Company Seal Water Heat Atlas Industrial 3621 N/A 2977 Exchanger Manufacturing Company Vertical Letdown Heat Joseph Oat 2268-2B N/A 944 Exchanger Corporation Regenerative Heat Joseph Oat 2255-1C3 N/A 877 Exchanger Corporation Residual Heat Joseph Oat 2A 2267-3C N/A 848 Removal Heat Corporation Exchanger 2B 2267-3D N/A 849 Containment Spray Joseph Oat 2A 2636-B N/A 3449 Heat Exchanger Corporation 2B 2636-C N/A 3456 Seal Water Injection Pall Trinity Micro 2A 35367 N/A 19025 Filter Corporation 2B 35366 N/A 19024 Volume Control Tank Lamco Industries 2286.30 N/A 77171 Inc.

EOC 14 Refueling Outage Report Page 3 of 5 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

Identification Numbers (Continued)

Manufacturer Manufacturer State or National Item or Installer or Installer Province No. Board Serial No. No.

Residual Heat Removal Ingersoll-Rand 2A 077647 N/A 237 Pump Pump 2B 077648 N/A 238 Containment Spray Pump Bingham- 2A 230342 N/A 215 Willamette 2B 230343 N/A 216 Safety Injection Pump Pacific Pumps 2A 49361 N/A 240 2B 49362 N/A 241 Centrifugal Charging Pump Pacific Pumps 2A 49780 N/A 262 2B 49779 N/A 259 1.2 Personnel. Equipment and Material Certifications All personnel who performed or evaluated the results of inservice inspections during the time frame bracketed by the examination dates shown on the NIS-1 Form were certified in accordance with the requirements of the 1998 Edition of ASME Section XI with 2000 addenda including Appendix VII for ultrasonic inspections. In addition, ultrasonic examiners were qualified in accordance with ASME Section XI, Appendix VIII,1995 Edition with the 1996 Addenda through the Performance Demonstration Initiative (PDI) for welds and components within the scope of Appendix VIII.

The appropriate certification records for each inspector, calibration records for inspection equipment, and records of materials used (i.e. NDE consumables) are on file at Catawba Nuclear Station or copies may be obtained by contacting the Duke Energy Corporate Office in Charlotte, North Carolina.

The copies of the certification records for Washington Group and Atlantic Group inspectors can be obtained by contacting the Duke Energy Corporate Office in Charlotte, North Carolina.

EOC 14 Refueling Outage Report Page 4 of 5 Catawba Unit 2 Revision 0 Section 1 June 20,2006

'..a.3 Reference Documents The following reference documents apply to the inservice inspections performed during this report period. A copy may be obtained by contacting the ISI Plan Manager at Duke Energy's Corporate Office in Charlotte, North Carolina.

Duke Energy's Catawba Nuclear Station, Unit 2 Docket Number 50-414, Request for Relief Serial Number (To Be Filed Later) Limited Weld Coverage During End-of-Cycle 14 Refueling Outage 1.4 Augmented and Elective Examinations Augmented and elective examination information found within this Inservice Inspection Owner's Summary Report is not required by the ASME Section XI Code; therefore, it is exempt from ANII review, verification, and/or record certification.

1.5 Responsible Inspection Agency The Hartford Steam Boiler Inspection and Insurance Company of Connecticut is responsible for the third party inspections required by ASME Section XI.

Authorized Nuclear Inservice Inspector(s)

Name: R. N. McGill Employer: The Hartford Steam Boiler Inspection & Insurance Company of Connecticut Business 200 Ashford Center North Address: Suite 205 Atlanta, GA 30338-4860 (800) 417-3721 www.hsbct.com EOC 14 Refueling Outage Report Page 5 of 5 Catawba Unit 2 Revision 0 Section 1 June 20, 2006

'2.0 Second Ten-Year Interval Inspection Status The completion status of inspections required by the 1998 ASME Code Section XI, 2000 addenda, is summarized in this section. The requirements are listed by the ASME Section XI Examination Category as defined in Table IWB-2500-1 for Class 1 Inspections, Table IWC-2500-1 for Class 2 Inspections, and IWF-2500-1 for Class 1, 2 and 3 Component Supports. Augmented / Elective Inspections are also included.

Class 1 Inspections Examination Description Inspections Inspections Percentage 'Deferral Category Required Completed Completed Allowed B-A Pressure Retaining Welds 25 0 0% Yes in Reactor Vessel B-B Pressure Retaining Welds 5 0 0% No in Vessels Other than Reactor Vessels B-D Full Penetration Welds of 36 0 0% Partial Nozzles in Vessels Inspection Program B B-E Pressure Retaining Partial REFERENCE SECTION 6.0 OF THIS REPORT Penetration Welds in Vessels B-F Pressure Retaining 26 0 0% No Dissimilar Metal Welds B-G-1 Pressure Retaining Bolting 217 54 24.88% Yes Greater than 2" in Diameter B-G-2 Pressure Retaining Bolting 27 0 0% No 12" and Less in Diameter B-J Pressure Retaining Welds 243 22 9.10% No I in Piping I I _III

\,OC 14 Refueling Outage Report Page 1 of 4 Catawba Unit 2 Revision 0 Section 2 June 20, 2006

Class I Inspections (Continued) 1Deferral Examination Description Inspections Inspections Percentage Category Required Completed Completed Allowed B-K Integral Attachments for 5 0 0% No Piping, Pumps and Valves B-L-1 Pressure Retaining Welds N/A N/A N/A N/A in Pump Casings B-L-2 Pump Casings 1 0 0% Yes B-M-1 Pressure Retaining 1 0 0% Yes Welds in Valve Bodies B-M-2 Valve Body > 4 in. 7 0 0% Yes Nominal Pipe Size B-N-1 Interior of Reactor Vessel 3 0 0% No B-N-2 Integrally Welded Core Support Structures and 2 0 0% Yes Interior Attachments to Reactor Vessels B-N-3 Removable Core Support 1 0 0% Yes

, _ __ __ Structures B-O Pressure Retaining Welds 3 0 0% Yes in Control Rod Housings B-P All Pressure Retaining REFERENCE SECTION 6.0 OF THIS REPORT Components B-Q Steam Generator Tubing See Note 2 below F-A Class 1 Component 70 8 11.43% No Supports Notes:

1. Deferral of Inspection to the end of the Interval as allowed by ASME Section XI Table IWB 2500-1.

These examination categories are exempt from percentage requirements per IWB-2412 (a), Inspection Program B.

2. Steam Generator Tubing is examined and documented by Nuclear Technical Services as required by the Station Technical Specifications and is not included in this report.

\-.AOC 14 Refueling Outage Report Page 2 of 4 Catawba Unit 2 Revision 0 Section 2 June 20, 2006

Class 2 Inspections Examination Description Inspections Inspections Percentage Category Required Completed Completed C-A Pressure Retaining Welds 30 0 0%

in Pressure Vessels C-B Pressure Retaining Nozzle 13 0 0%

Welds in Vessels C-C Integral Attachments for 28 0 0%

Vessels, Piping, Pumps, and Valves C-D Pressure Retaining Bolting N/A N/A N/A Greater Than 2" in Diameter C-F-1 Pressure Retaining Welds 300 24 8%

in Austenitic Stainless Steel or High Alloy Piping C-F-2 Pressure Retaining Welds 63 3 4.76%

in Carbon or Low Alloy Steel Piping C-G Pressure Retaining Welds 21 1 4.76%

in Pumps and Valves C-H All Pressure Retaining REFERENCE SECTION 6.0 OF THIS Components REPORT F-A Class 2 Component 247 33 13.36%

Supports KJOC 14 Refueling Outage Report Page 3 of 4 Catawba Unit 2 Revision 0 Section 2 June 20, 2006

Augmented I Elective Inspections Description PercentageComplete Postulated Pipe Failures 100% of requirements for Outage 7 / EOC-1 4 Pressurizer Bare Metal Visual Examinations 100% of requirements for Outage 7/ EOC-1 4 (NRC Bulletin 2004-01) _

\..EOC 14 Refueling Outage Report Page 4 of 4 Catawba Unit 2 Revision 0 Section 2 June 20, 2006

.0 Final Inservice Inspection Plan The final Inservice Inspection Plan shown in this section lists all ASME Section XI Class 1, Class 2, and Augmented / Elective inspections credited for this report period.

The information shown below is a field description for the reporting format included in this section of the report:

ITEM NUMBER = ASME Section XI Tables IWB-2500-1 (Class 1), IWC-2500-1 (Class 2), IWF-2500-1 (Class 1 and Class 2 ), Augmented / Elective Requirements ID NUMBER = Unique Identification Number SYS = Component System Identification ISO / DWG NUMBERS = Location and / or Detail Drawings PROC = Examination Procedures INSP REQ = Examination Technique - Magnetic Particle, Dye Penetrant, etc.

MAT/ SCH = General Description of Material DIA / THICK = Diameter / Thickness CAL BLOCKS = Calibration Block Number COMMENTS = General and / or Detail Description

ý-iOC14 Refueling Outage Report Page 1 of 1 Catawba Unit 2 Revision 0 Section 3 June 20, 2006

EOC 14 DUKE ENERt"CORPORATION C CATEGORY B-G-1, Pressure Retalninq Bolting, INSERVICE INSPECTION PLAN MANAGEMENT Greater Than 2 In. In Diameter Inservice Inspection Database Management System Plan Report Reactor Vessel Catawba 2 Page 1 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIArTHK CAL BLOCKS COMMENTS

• • • • Closure Studs, In place ****

B06.010.001 2RPV-179-102-01 E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.002 2RPV-179-102-02A E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.003 2RPV-179-102-03 E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.004 2RPV-179-102-04 E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.005 2RPV-179-102-05A E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.006 2RPV-179-102-Si E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.007 2RPV-179-102-07 E 8871-179-001 OAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.008 2RPV-179-102-08A E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A

EOC 14 ( DUKE ENER*4 CORPORATION (

CATEGORY B-G-1, Pressure Retaining Bolting. INSERVICE INSPECTION PLAN MANAGEMENT Greater Than 2 In. In Diameter Inservice Inspection Database Management System Plan Report

~eactor Vessel Catawba 2 Page 2 Inservlce Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MATISCH DIAITHK CAL BLOCKS COMMENTS B06.010.009 2RPV-179-102-09A E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.010 2RPV-179-102-10 E 8871-179-001 QAL-13 VT-i CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.011 2RPV-179-102-11 E 8871-179-001 QAL-13 VT-i CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.012 2RPV-179-102-12 E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.013 2RPV-179-102-13A E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.014 2RPV-179-102-14 E 8871-179-001 QAL-13 VT-i CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.015 2RPV-179-102-15 E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.016 2RPV-179-102-16 E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A B06.010.017 2RPV-179-102-17 E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM2201.01-67 1.857 Class A

(

EOC 14 DUKE ENER(, ,;ORPORATION (

CATEGORY B-G-1, Pressure Rietaininq Bolting, INSERVICE INSPECTION PLAN MANAGEMENT Greater Than 2 In. In Diameter Inservice Inspection Database Management System Plan Report W~eatorVessel Catawba 2 Page 3 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAJTHK CAL BLOCKS COMMENTS B06.010.018 2RPV-179-102-18 E 8871-179-001 QAL-13 VT-1 CS 10.580 Reactor Vessel Closure Head Nut.

NC CNM 2201.01-67 1.857 Class A Items: 18 Total B06.O1O 906.010 Items: is

EOC 14 CATEGORY B-G-1, Pressure Retalning Boltln.,

DUKE ENER(G ,ORPORATION INSERVICE INSPECTION PLAN MANAGEMENT C

Greater Than 2 In. In Diameter Inservice Inspection Database Management System Plan Report IReactor Vessel Catawba 2 Page 4 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER PROC INSP REO MAT/SCH DIA/THK CAL BLOCKS COMMENTS SYS ISO/DWG NUMBERS PROC INSP REQ MATISCH DlArrHK CAL BLOCKS COMMENTS

• • • • Threads In Flange ****

B06.030.001 2RPV-179-101-01 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.002 2RPV-179-101-02A E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.003 2RPV-179-101-03 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.004 2RPV-179-101-04 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.005 2RPV-179-101-05A E 8871-179-001 PD0-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.006 2RPV-179-101-S1 E 8871-179-001 PD1-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.007 2RPV-179-101-07 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.008 2RPV-179-101-08 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A

EOC 14 - DUKE ENERI. ;ORPORATION (

CATEGORY B-G-1, Pressure Retaining Bolting, INSERVICE INSPECTION PLAN MANAGEMENT Greater Than 2 in. In Diameter Inservice Inspection Database Management System Plan Report Res2or Vessel Catawba 2 Page 5 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS B06.030.009 2RPV-179-101-09 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.010 2RPV-179-101-10 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.011 2RPV-179-101-11 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.012 2RPV-179-101-12 E 8871-179-001 PD0-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.013 2RPV-179-101-13 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.014 2RPV-179-101-14 E 8871-179-001 PD1-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.015 2RPV-179-101-15 E 8871-179-001 PD1-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.016 2RPV-179-101-16 E 8871-179-001 PD0-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A B06.030.017 2RPV-179-101-17 E 8871-179-001 PD0-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A

EOC 14 DUKE ENER( ,;ORPORATION CATEGORY B-G-1, Pressure Retaining Baiting, INSERVICE INSPECTION PLAN MANAGEMENT Greater Than 2 In. In Diameter Inservice Inspection Database Management System Plan Report WRector Vessel Catawba 2 Page 6 N Inservice Inspection Plan for Interval 3 Outage I 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS B06.030.018 2RPV-179-101-18 E 8871-179-001 PDI-UT-5 UT CS 7.000 50501 Reactor Vessel Closure Head Stud.

NC CNM 2201.01-67 57.688 Class A Total B06.030 Items: 18

EOC 14 ( C DUKE ENERf, CORPORATION CATEGORY B-G-1, Pressure Retalninfi Bolting, INSERVICE INSPECTION PLAN MANAGEMENT Greater Than 2 in. In Diameter Inservice Inspection Database Management System Plan Report Pressurizer Catawba 2 Page 7 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUME3ERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• • • • Bolts and Studs ****

B06.050.001 2RPV-179-103-01 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.002 2RPV-179-103-02A E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.003 2RPV-179-103-03 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.004 2RPV-179-103-04 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.005 2RPV-179-103-05A E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.006 2RPV-179-103-S1 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.007 2RPV-179-103-07 E 8871-179-001 OAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.008 2RPV-1 79-103-08 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A

EOC 14 DUKE ENERG( CORPORATION C CATEGORY B-G-l, Pressure Retaining Bolting, INSERVICE INSPECTION PLAN MANAGEMENT Greater Than 2 In. In Diameter Inservice Inspection Database Management System Plan Report Pressurizer Catawba 2 Page 8 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS B06.050.009 2RPV-179-103-09 E 8871-179-001 QAL-1 3 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.01 0 2RPV-179-103-10 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.011 2RPV-179-103-11 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.012 2RPV-179-103-12 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.013 2RPV-179-103-13A E 8871-179-001 QAL-13 VT-I CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.014 2RPV-179-103-14 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.015 2RPV-179-103-15 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.016 2RPV-179-103-16 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A B06.050.017 2RPV-179-103-17 E 8871-179-001 OAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A

EOC 14 ( DUKE ENERC( %:ORPORATION C CATEGORY B-G-1, Pressure Retaining Bolting, INSERVICE INSPECTION PLAN MANAGEMENT Greater Than 2 In. In Diameter Inservice Inspection Database Management System Ph an Report Pressurlzer Catawba 2 Page 9 e1 0*6/20/2006 Inservice Inspection Plan for Interval 3 Outag ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MATISCH DIA/THK CA,L BLOCKS COMMENTS B06.050.018 2RPV-179-103-18 E 8871-179-001 QAL-13 VT-1 CS 10.560 Reactor Vessel Closure Head Washer.

NC CNM 2201.01-67 1.719 Class A Total B06.050 Items: 18 Total B06 Items: 54

EOC 14 CATEGORY B-J, Pressure Retaining Welds In DUKE ENERC( ..ORPORATION C INSERVICE INSPECTION PLAN MANAGEMENT Piping Inservice Inspection Database Management System Plan Report Less han NPS 4 Catawba 2 Page 10 Inservice Inspection Plan for Interval 3 Outage I 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS B09.011.032 2NC24-11 CN-2NC-24 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NC CN-ISIN3-2553-1.1 PDI-UT-2 160 0.531 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Elbow to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

B09.011.032A 2NC24-11 CN-2NC-24 NDE-35 PT SS 4.000 Circumferential NC CN-ISIN3-2553-1.1 160 0.531 Class A Elbow to Pipe B09.011.033 2NC24-17 CN-2NC-24 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NC CN-ISIN3-2553-1.1 PDI-UT-2 160 0.531 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

B09.011.033A 2NC24-17 CN-2NC-24 NDE-35 PT SS 4.000 Circumferential NC CN-ISIN3-2553-1.1 160 0.531 Class A Pipe to Elbow B09.011.034 2NC24-7 CN-2NC-24 NDE-600 UT SS 6.000 Component Procedure NDE-600 uses the component for Circumferential NC CN-ISIN3-2553-1.1 PDI-UT-2 160 0.719 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Elbow to of NDE-600. If PDI-UT-2 is used, then the Reducer calibration block listed shall be used.

B09.011.034A 2NC24-7 CN-2NC-24 NDE-35 PT SS 6.000 Circumferential NC CN-ISIN3-2553-1.1 160 0.719 Class A Elbow to Reducer B09.011.035 2NC24-8 CN-2NC-24 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NC CN-ISIN3-2553-1.1 PDI-UT-2 160 0.531 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Reducer to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

B09.011.035A 2NC24-8 CN-2NC-24 NDE-35 PT SS 4.000 Circumferential NC CN-ISIN3-2553-1.1 160 0.531 Class A Reducer to Pipe

EOC 14 ( C DUKE ENERIC JORPORATION CATEGORY B-J, Pressure Retalning Welds In INSERVICE INSPECTION PLAN MANAGEMENT Peipng Inservlce Inspection Database Management System Plan Report Page 11 WLesshan NPS 4 Catawba 2 06/20/2006 Inservice Inspection Plan for Interval 3 Outage 1 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIANTHK CAL BLOCKS COMMENTS B09.011.165 2NI55-11 CN-2NI-55 NDE-600 UT SS 10.000 Component Procedure NDE-600 uses the component for Circumferential NI CN-ISIN3-2562-1.1 PDI-UT-2 140 1.000 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Valve 2NI081 to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

B09.011.165A 2NI55-11 CN-2NI-55 NDE-35 PT SS 10.000 Circumferential NI CN-ISIN3-2562-1.1 140 1.000 Class A Valve 2NI081 to Pipe B09.011.166 2NI55-12 CN-2NI-55 NDE-600 UT SS 10.000 Component Procedure NDE-600 uses the component for Circumferential NI CN-ISIN3-2562-1.1 PDI-UT-2 140 1.000 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

B09.011.166A 2NI55-12 CN-2NI-55 NDE-35 PT SS 10.000 Circumferential NI CN-ISIN3-2562-1.1 140 1.000 Class A Pipe to Elbow B09.011.167 2NI55-14 CN-2NI-55 NDE-600 UT SS 10.000 Component Procedure NDE-600 uses the component for Circumferential NI CN-ISIN3-2562-1.1 PDI-UT-2 140 1.000 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

B09.011.167A 2NI55-14 CN-2NI-55 NDE-35 PT SS 10.000 Circumferential NI CN-ISIN3-2562-1.1 140 1.000 Class A Pipe to Elbow B09.011.168 2NI55-2 CN-2NI-55 NDE-600 UT SS 6.000 Component Procedure NDE-600 uses the component for Circumferential NI CN-oSIN3-2562-1.1 PDI-UT-2 160 0.719 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

B09.011.168A 2NI55-2 CN-2NI-55 NDE-35 PT SS 6.000 Circumferential NI CN-ISIN3-2562-1.1 160 0.719 Class A Pipe to Elbow B09.011.169 2NI55-4 CN-2NI-55 NDE-600 UT SS 6.000 Component Procedure NDE-600 uses the component for Circumferential NI CN-ISIN3-2562-1 .1 PDI-UT-2 160 0.719 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

EOC 14 DUKE ENERC( CORPORATION (

CATEGORY B-J, Pressure Retaininq Welds In INSERVICE INSPECTION PLAN MANAGEMENT PipingS Inservice Inspection Database Management System Plan Report Catawba 2 Page 12 Wess han NPS 4 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS B09.011.169A 2NI55-4 CN-2NI-55 NDE-35 PT SS 6.000 Circumferential NI CN-ISIN3-2562-1.1 160 0.719 Class A Pipe to Elbow B09.011.170 2NI55-6 CN-2NI-55 NDE-600 UT SS 6.000 Component Procedure NDE-600 uses the component for Circumferential NI CN-ISIN3-2562-1.1 PDI-UT-2 160 0.719 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

B09.011.170A 2NI55-6 CN-2NI-55 NDE-35 PT SS 6.000 Circumferential NI CN-ISIN3-2562-1.1 160 0.719 Class A Pipe to Elbow B09.011.171 2NI55-8 CN-2NI-55 NDE-600 UT SS 6.000 Component Procedure NDE-600 uses the component for Circumferential NI CN-ISIN3-2562-1.1 PDI-UT-2 160 0.719 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class A Pipe to of NDE-600. If PDI-UT-2 is used, then the Tee calibration block listed shall be used. Reference Elective Examination Item Number H01.001.001.

B09.011.171A 2NI55-8 CN-2NI-55 NDE-35 PT SS 6.000 Circumferential NI CN-ISIN3-2562-1.1 160 0.719 Class A Pipe to Tee Total B09.011 Items: 22

EOC 14 CATEGORY B-J, Pressure Retaining Welds In DUKE ENERr. CORPORATION (

INSERVICE INSPECTION PLAN MANAGEMENT P sueee Inservice Inspection Database Management System Plan Report N~essue Vssels Catawba 2 Page 13 Inservice Inspection Plan for Interval 3 Outage I 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• • • • Welded Attachments ****

B09.040.006 2NC44-27 CN-2NC-44 NDE-35 PT SS 2.000 Socket NC CN-ISIN3-2553-1.1 160 0.344 Class A Pipe to Valve 2NV038 B09.040.127 2NV323-1 0 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Elbow to Pipe B09.040.128 2NV323-11 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Pipe to Elbow 809.040.129 2NV323-12 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Elbow to Pipe B09.040.130 2NV323-16 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Tee to Pipe B09.040.131 2NV323-18 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Tee to Pipe B09.040.132 2NV323-19 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Pipe to Elbow B09.040.133 2NV323-20 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Elbow to Pipe

EOC 14 DUKE ENERGY, CORPORATION (

CATEGORY B-J. Pressure Reta ininq Welds In INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report NPressure Vessels Catawba 2 Page 14 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS B09.040.134 2NV323-22 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Valve 2NV060 to Pipe B09.040.135 2NV323-25 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Tee to Pipe B09.040.136 2NV323-26 CN-2NV-323 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class A Tee to Pipe Total B09.040 Items: 11 Total B09 Items: 33

EOC 14 CATEGORY (C-F-l, Pressure Retalninq Welds In DUKE INSERVICE ENER(. CORPORATION INSPECTION PLAN MANAGEMENT (

Austenitic SS Or Hlqh Alloy Piping Inservice Inspection Database Management System Plan Report PI in Welds> 1/ In. Nom Wall for Pi In >= Catawba 2 Page 15 NPS 2 and <= NPS 4 Inservice Inspection Plan for Interval 3 Outag el 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAiTHK CAkL BLOCKS COMMENTS

• • • • Piping Welds > 1/5 In. Nom Wall For Piping >= NPS 2 And <= NPS 4

• C05.011.008 2CA1 53-49 CN-2CA-153 NDE-600 UT SS 6.000 Component Procedure NDE-600 uses the component for Circumferential CA CN-ISIN3-2592-1.1 PDI-UT-2 80 0.432 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Elbow to of NDE-600. IfPDI-UT-2 is used, then the Elbow calibration block listed shall be used.

C05.011.008A 2CA1 53-49 CN-2CA-153 NDE-35 PT SS 6.000 Circumferential CA CN-ISIN3-2592-1.1 80 0.432 Class B Elbow to Elbow C05.011.009 2CA1 53-50 CN-2CA-153 NDE-600 UT SS 6.000 Component Procedure NDE-600 uses the component for Circumferential CA CN-ISIN3-2592-1.1 PDI-UT-2 80 0.432 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

C05.01 1.009A 2CA1 53-50 CN-2CA-153 NDE-35 PT SS 6.000 Circumferential CA CN-ISIN3-2592-1.1 80 0.432 Class B Pipe to Elbow C05.011.101 2FW76-1 CN-2FW-76 NDE-600 UT SS 12.000 Component Procedure NDE-600 uses the component for Circumferential FW CN-ISIN3-2571-1.0 PDI-UT-2 STD 0.375 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Elbow to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

C05.011.101A 2FW76-1 CN-2FW-76 NDE-35 PT SS 12.000 Circumferential FW CN-ISIN3-2571-1.0 STD 0.375 Class B Elbow to Pipe C05.011.164 2ND2-1 CN-2ND-2 NDE-600 UT SS 12.000 Component Procedure NDE-600 uses the component for Circumferential ND CN-ISIN3-2561-1.0 PDI-UT-2 STD 0.375 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used Inlieu Class B Elbow to of NDE-600. If PDI-UT-2 Is used, then the Pipe calibration block listed shall be used.

C05.011.164A 2ND2-1 CN-2ND-2 NDE-35 PT SS 12.000 Circumferential ND CN-ISIN3-2561-1.0 STD 0.375 Class B Elbow to Pipe

EOC 14 ( DUKE ENERC CORPORATION (

CATEGORY C-F-l, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS Or High Alloy Piping Inservice Inspection Database Management System Plan Report

• PiInal Welds > 115 In. Nom Wall for Piplng >= Catawba 2 Page 16 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 WENPS 2 and <= NPS 4 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS C05.011.165 2ND2-10 CN-2ND-2 NDE-600 UT SS 12.000 Component Procedure NDE-600 uses the component for Circumferential ND CN-ISIN3-2561-1.0 PDI-UT-2 STD 0.375 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

C05.011.165A 2ND2-10 CN-2ND-2 NDE-35 PT SS 12.000 Circumferential ND CN-ISIN3-2561-1.0 STD 0.375 Class B Pipe to Elbow C05.011.166 2ND2-11 CN-2ND-2 NDE-600 UT SS 12.000 Component Procedure NDE-600 uses the component for Circumferential ND CN-ISIN3-2561-1.0 PDI-UT-2 STD 0.375 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Elbow to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

C05.011.166A 2ND2-11 CN-2ND-2 NDE-35 PT SS 12.000 Circumferential ND CN-ISIN3-2561-1.0 STD 0.375 Class B Elbow to Pipe C05.011.167 2ND2-2 CN-2ND-2 NDE-600 UT SS 12.000 Component Procedure NDE-600 uses the component for Circumferential ND CN-ISIN3-2561-1.0 PDI-UT-2 STD 0.375 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used In lieu Class B Pipe to of NDE-600. If PDI-UT-2 Is used, then the Elbow calibration block listed shall be used.

C05.011.167A 2ND2-2 CN-2ND-2 NDE-35 PT SS 12.000 Circumferential ND CN-ISIN3-2561-1.0 STD 0.375 Class B Pipe to Elbow C05.011.168 2ND2-3 CN-2ND-2 NDE-600 UT SS 12.000 Component Procedure NDE-600 uses the component for Circumferential ND CN-ISIN3-2561-1.0 PDI-UT-2 STD 0.375 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used In lieu Class B Elbow to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

C05.011.168A 2ND2-3 CN-2ND-2 NDE-35 PT SS 12.000 Circumferential ND CN-ISIN3-2561-1.0 STD 0.375 Class B Elbow to Pipe C05.011.169 2ND2-9 CN-2ND-2 NDE-600 UT SS 12.000 Component Procedure NDE-600 uses the component for Circumferential ND CN-ISIN3-2561-1.0 PDI-UT-2 STD 0.375 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Elbow to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

EOC 14 ( DUKE ENER( CORPORATION (

CATEGORY C-F-I, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS Or High Alloy Pipinq Inservice Inspection Database Management System L

WNPS Ploina Welds > 1/5 In. Nom Wall for Piping >

2 and <= NPS 4 Inservice Catawba 2 Inspection Plan for Interval 3 Outagiel Plan Report Page 17 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CA\L BLOCKS COMMENTS C05.011.169A 2ND2-9 CN-2ND-2 NDE-35 PT SS 12.000 Circumferential ND CN-ISIN3-2561-1.0 STD 0.375 Class B Elbow to Pipe Total C05.011 Items: 18

EOC 14 (

CATEGORY C-F-l, Pressure Retainincq Welds In DUKE ENERC, CORPORATION INSERVICE INSPECTION PLAN MANAGEMENT C

Austenitic SS Or HI-ih Alloy PIDIng Inservice Inspection Database Management System Plan Report Socket Welds Catawba 2 Page 18 N Inservice Inspection Plan for Interval 3 Outage 1 0W/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MATISCH DIA/THK CAL BLOCKS COMMENTS C05.021.201 2NV1 04-1 CN-2NV-104 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.6 PDI-UT-2 40 0.237 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Elbow to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

C05.021.201A 2NV104-1 CN-2NV-104 NDE-35 PT SS 4.000 Circumferential NV CN-ISIN3-2554-1.6 40 0.237 Class B Elbow to Pipe C05.021.202 2NV104-2 CN-2NV-104 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.6 PDI-UT-2 40 0.237 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

C05.021.202A 2NV104-2 CN-2NV-104 NDE-35 PT SS 4.000 Circumferential NV CN-ISIN3-2554-1.6 40 0.237 Class B Pipe to Elbow C05.021.203 2NV1 1-16 CN-2NV-1 1 NDE-600 UT SS 3.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.7 PDI-UT-2 160 0.438 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Elbow to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

C05.021.203A 2NV11-16 CN-2NV-1 1 NDE-35 PT SS 3.000 Circumferential NV CN-ISIN3-2554-1.7 160 0.438 Class B Elbow to Elbow C05.021.204 2NV1 1-18 CN-2NV-1 1 NDE-600 UT SS 3.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.7 PDI-UT-2 160 0.438 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Pipe to of NDE-600. If PDI-UT-2 is used, then the 90 Degree Elbow calibration block listed shall be used.

C05.021.204A 2NV11-18 CN-2NV-11 NDE-35 PT SS 3.000 Circumferential NV CN-ISIN3-2554-1.7 160 0.438 Class B Pipe to 90 Degree Elbow

EOC 14 ( DUKE ENERG? .;ORPORATION (

CATEGORY C-F-i, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitlc SS Or Hla-h Alloy Pipinq Inservice Inspection Database Management System Plan Report Catawba 2 Page 19 iWSoctWeds Inservice Inspection Plan for Interval 3 Outage I 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.021.205 2NV1 1-20 CN-2NV-i1 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.7 PDI-UT-2 160 0.531 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Elbow to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

C05.021.205A 2NVl 1-20 CN-2NV-11 NDE-35 PT SS 4.000 Circumferential NV CN-ISIN3-2554-1.7 160 0.531 Class B Elbow to Pipe C05.021.206 2NV1 1-21 CN-2NV-1 1 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.7 PDI-UT-2 160 0.531 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used In lieu Class B Pipe to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

C05.021.206A 2NV11-21 CN-2NV-11 NDE-35 PT SS 4.000 Circumferential NV CN-ISIN3-2554-1.7 160 0.531 Class B Pipe to Elbow C05.021.207 2NV1 1-7 CN-2NV-1 1 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.7 PDI-UT-2 160 0.531 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Pipe to of NDE-600. If PDI-UT-2 Is used, then the Tee calibration block listed shall be used.

C05.021.207A 2NV1 1-7 CN-2NV-1 1 NDE-35 PT SS 4.000 Circumferential NV CN-ISIN3-2554-1.7 160 0.531 Class B Pipe to Tee C05.021.208 2NV1 1-8 CN-2NV-1 1 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.7 PDI-UT-2 160 0.531 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Tee to of NDE-600. If PDI-UT-2 is used, then the Pipe calibration block listed shall be used.

C05.021.208A 2NV1 1-8 CN-2NV-1 1 NDE-35 PT SS 4.000 Circumferential NV CN-ISIN3-2554-1.7 160 0.531 Class B Tee to Pipe C05.021.209 2NV12-10 CN-2NV-12 NDE-600 UT SS 4.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.7 PDI-UT-2 160 0.531 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B Tee to of NDE-600. If PDI-UT-2 Is used, then the 4X3 Reducer calibration block listed shall be used.

EOC 14 C DUKE ENERC(...ORPORATION C CATEGORY C-F-i, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT Austenitic SS Or HI-h Alloy Piping Inservice Inspection Database Management System Plan Report Esocket Welds Catawba 2 Page 20 M Inservlce Inspection Plan for Interval 3 Outag el 06W20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.021.209A 2NV12-10 CN-2NV-12 NDE-35 PT SS 4.000 Circumferential NV CN-ISIN3-2554-1.7 160 0.531 Class B Tee to 4X3 Reducer C05.021.210 2NV12-11 CN-2NV-12 NDE-600 UT SS 3.000 Component Procedure NDE-600 uses the component for Circumferential NV CN-ISIN3-2554-1.7 PDI-UT-2 160 0.438 PDI-UT-2-C calibration. Procedure PDI-UT-2 may be used in lieu Class B 4X3 Reducer to of NDE-600. If PDI-UT-2 is used, then the Elbow calibration block listed shall be used.

C05.021.210A 2NV12-11 CN-2NV-12 NDE-35 PT SS 3.000 Circumferential NV CN-ISIN3-2554-1.7 160 0.438 Class B 4X3 Reducer to Elbow Total C05.021 Items: 20

EOC 14 - DUKE ENERd 2 CATEGORY C-F-l, Pressure Retaining Welds In INSERVICE INSPECTION PLAN MANAGEMENT

.;ORPORATION C Austenitic SS Or High Alloy Pipinq Inservice Inspection Database Management System Plan Report Wine Branch Connections of Branch PipIng > Catawba 2 Page 21 NPS 2 InservIce Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS C05.030.108 2NV242-1 0 CN-2NV-242 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class B Pipe to Tee C05.030.109 2NV242-11 CN-2NV-242 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class B Tee to Pipe C05.030.1 10 2NV242-3 CN-2NV-242 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class B Elbow to Pipe C05.030.1 11 2NV242-4 CN-2NV-242 NDE-35 PT SS 2.000 Socket NV CN-ISIN3-2554-1.5 160 0.344 Class B Pipe to Elbow Total C05.030 Items: 4

EOC 14 ( '

CATEGORY C-F-I. Pressure Retaining Welds In DUKE ENERGJ;ORPORATION INSERVICE INSPECTION PLAN MANAGEMENT

(

Austenitic SS Or High Alloy Piping Inservice Inspection Database Management System Plan Report PPDLng Welds >=3/8 In. Nominal Wall Thickness Catawba 2 Page 22 orPipin> NPS 4 InservIce Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.041.031 2NI100-9 CN-2NI-100 NDE-35 PT SS 2.000 Branch NI CN-ISIN3-2562-1.2 80 0.218 Class B Pipe to Half Coupling Total C05.041 Items: 1

EOC 14 ( DUKE ENERJC..ORPORATION CATEGORY C-F-2, Pressure Retalninq Welds In INSERVICE INSPECTION PLAN MANAGEMENT Carbon Or Low Alloy Steel PIpIncq Inservice Inspection Database Management System Plan Report P1 In Welds> 1/5 In. Nom Wall for Pi in >= Catawba 2 Page 23 ENPS 2 and <= NPS 4 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS C05.051.001 2CA59-11 CN-2CA-59 NDE-600 UT CS 6.000 Component Procedure NDE-600 uses the component for Circumferential CA CN-ISIN3-2592-1.1 PDI-UT-1 80 0.432 PDI-UT-1-C calibration. Procedure PDI-UT-1 may be used in lieu Class B Elbow to of NDE-600. If PDI-UT-1 is used, then the Pipe calibration block listed shall be used.

C05.051.001A 2CA59-11 CN-2CA-59 NDE-25 MT CS 6.000 Circumferential CA CN-ISIN3-2592-1.1 80 0.432 Class B Elbow to Pipe C05.051.002 2CA59-8 CN-2CA-59 NDE-600 UT CS 6.000 Comoonent Procedure NDE-600 uses the comoonent for Circumferential CA CN-ISIN3-2592-1.1 PDI-UT-1 80 0.432 PDI-UT-1-C calibration. Procedure PDI-UT-1 may be used in lieu Class B Pipe to of NDE-600. If PDI-UT-1 Is used, then the Elbow calibration block listed shall be used.

C05.051.002A 2CA59-8 CN-2CA-59 NDE-25 MT CS 6.000 Circumferential CA CN-ISIN3-2592-1.1 80 0.432 Class B Pipe to Elbow C05.051.155 2SV8-2 CN-2SV-8 NDE-600 UT CS 9.000 Component Procedure NDE-600 uses the component for Circumferential SV CN-ISIN3-2593-1.0 PDI-UT-1 40 1.500 PDI-UT-1-C calibration. Procedure PDI-UT-1 may be used in lieu Class B Pipe to of NDE-600. If PDI-UT-1 is used, then the Valve 2SV009 calibration block listed shall be used.

C05.051.155A 2SV8-2 CN-2SV-8 NDE-25 MT CS 9.000 Circumferential SV CN-ISIN3-2593-1.0 40 1.500 Class B Pipe to Valve 2SV009 Total C05.051 Items: 6 Total C05 Items: 49

EOC 14

( DUKE ENER&i, ,ORPORATION C CATEGORY C-G, Pressure Reta ininq Welds In INSERVICE INSPECTION PLAN MANAGEMENT Pumps And Valves Inservice Inspection Database Management System Plan Report Pressure Vessels Catawba 2 Page 24 InservIce Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• • • • Welded Attachments ****

C06.020.018 2SV-2 CNM 1205.09-02 NDE-35 PT SS-CS 9.000 Valve Body Weld - Valve Numbers in Valve Group Circumferential SV CN-ISIN3-2593-1.0 1.500 2SV-2, 2SV-3, 2SV-4, 2SV-5, 2SV-6.

Class B Weld lAD Valve Inlet Neck to Base Total C06.020 Items: 1 Total C06 Items: 1

EOC 14

( DUKE ENER? %;ORPORATION C CATEGORY D-A. Welded Attachments For INSERVICE INSPECTION PLAN MANAGEMENT Vessels, Piping, Pumps. And Valves Inservice Inspection Database Management System Plan Report Catawba 2 Page 25 InservIce Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DW( 3 NUMBERS PROC INSP REQ MAT/SCH DINATHK CAL BLOCKS COMMENTS

• 1 Welded Attachments ****

D01.020.011 2-R-KC-0227 CN-2492-KCl 18 OAL-13 VT-1 NA 14.000 Inspect with F01.032.053.

Mech Snubber KC CN-ISIN3-2573-1.2 0.625 Class C D:01.020.012 2-R-KC-0001 CN-2492-KC073 OAL-13 VT-1 NA 16.000 Inspect with F01.032.051.

Spring Hgr KC CN-ISIN3-2573-2.0 0.750 Class C D01.020.013 2-R-KC-0054 CN-2492-KC095 OAL-13 VT-1 NA 16.000 Inspect with F101.032.052.

Spring Hgr KC CN-ISIN3-2573-2.1 0.750 Class C Total D01.020 Items: 3 Total D01 Items: 3

EOC 14 ( (

DUKE ENERG4;ORPORATION CATEGORY F-A. SupDorts INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Cass I PIiSup s Catawba 2 Page 26 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUME3ER SYS ISO/DWG NUMBErRS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• Category A, One-Directional

• FO1.010.001 2-R-NC-1022 CN-2491-NCO04 QAL-14 VT-3 NA 2.000 Rigid Support NC CN-ISIN3-2553-1.1 0.000 Class A F01.010.002 2-R-NC-1024 CN-2491-NCO04 QAL-14 VT-3 NA 2.000 Rigid Support NC CN-ISIN3-2553-1.1 0.000 Class A Total F01.010 Items: 2

• • • • Category B, Multi-Directional F01.011.051 2-R-NI-1759 CN-2491-NI009 OAL-14 VT-3 NA 10.000 Rigid Restraint NI CN-ISIN3-2562-1.1 0.000 Class A F01.011.052 2-R-NI-1761 CN-2491-NI009 QAL-14 VT-3 NA 10.000 Rigid Restraint NI CN-ISIN3-2562-1.1 0.000 Class A Total F01.011 Items: 2

• • • • Category C, Thermal Movement F01.012.001 2-R-NC-1028 CN-2491-NCO04 OAL-14 VT-3 NA 2.000 Spring Hgr NC CN-ISIN3-2553-1.1 0.000 Class A F01.012.051 2-R-NI-1086 CN-2491-NI002 QAL-14 VT-3 NA 1.500 Spring Hgr NI CN-ISIN3-2562-1.1 0.000 Class A F01.012.052 2-R-NI-1762 CN-2491-NI009 QAL-14 VT-3 NA 10.000 Spring Hgr NI CN-ISIN3-2562-1.1 0.000 Class A Total F01.012 Items: 3

EOC 14 CATEGORY F-A. Sulanorts DUKE ENERJC .dORPORATION (

INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report MClass 2 PIPIna Supports Catawba 2 Page 27 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 N

ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS I Category A, One-Directional ****

F01.020.001 2-R-CA-1614 CN-2491-CA.00-001 QAL-14 VT-3 NA 6.000 Rigid Support CA CN-ISIN3-2592-1.1 0.000 Class B F01.020.002 2-R-CA-1620 CN-2491-CA.00-001 QAL-14 VT-3 NA 6.000 Rigid Support CA CN-ISIN3-2592-1.1 0.000 Class B F01.020.003 2-R-CA-1622 CN-2491-CA.00-001 OAL-14 VT-3 NA 6.000 Rigid Support CA CN-ISIN3-2592-1.1 0.000 Class B F01.020.021 2-R-FW-0116 CN-2492-FW019 QAL-14 VT-3 NA 12.000 Rigid Support FW CN-ISIN3-2571-1.0 0.000 Class B F01.020.031 2-R-ND-0319 CN-2492-ND026 QAL-14 VT-3 NA 8.000 Rigid Support ND CN-ISIN3-2561-1.1 0.000 Class B F01.020.032 2-R-ND-0321 CN-2492-ND026 QAL-14 VT-3 NA 8.000 Rigid Support ND CN-ISIN3-2561-1.1 0.000 Class B F01.020.033 2-R-ND-0323 CN-2492-ND026 OAL-14 VT-3 NA 8.000 Rigid Support ND CN-ISIN3-2561 -1.1 0.000 Class B F01.020.061 2-R-NI-1769 CN-2491-NI006 QAL-14 VT-3 NA 6.000 Rigid Support NI CN-ISIN3-2562-1 .1 0.000 Class B

EOC 14 DUKE ENERG ..;ORPORATION C CATEGORY F-A, Supports INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 28 M~ls2 PipingSurnorts Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS F01.020.062 2-R-NI-1770 CN-2491-NI007 QAL-14 VT-3 NA 6.000 Rigid Support NI CN-ISIN3-2562-1.3 0.000 Class B F01.020.063 2-R-NI-1623 CN-2491-NI008 QAL-14 VT-3 NA 6.000 Rigid Support NI CN-ISIN3-2562-1.3 0.000 Class B F01.020.091 2-R-NS-1220 CN-2491-NS001 QAL-14 VT-3 NA 8.000 Rigid Support NS CN-ISIN3-2563-1.0 0.000 Class B F01.020.092 2-R-NS-1221 CN-2491-NSOO1 OAL-14 VT-3 NA 8.000 Rigid Support NS CN-ISIN3-2563-1.0 0.000 Class B F01.020.093 2-R-NS-1250 CN-2491-NS001 QAL-14 VT-3 NA 8.000 Rigid Support NS CN-ISIN3-2563-1.0 0.000 Class B F01.020.141 2-R-NV-1170 CN-2491-NV036 OAL-14 VT-3 NA 2.000 Rigid Support NV CN-ISIN3-2554-1.5 0.000 Class B F01.020.142 2-R-NV-1171 CN-2491-NV036 QAL-14 VT-3 NA 2.000 Rigid Support NV CN-ISIN3-2554-1.5 0.000 Class B F01.020.143 2-R-NV-1 172 CN-2491 -NV036 QAL-14 VT-3 NA 2.000 Rigid Support NV CN-ISIN3-2554-1.5 0.000 Class B Total F011.020 Items: 16

• • • • Category B, Mufti-Directional ****

EOC 14 DUKE ENERGC,,ORPORATION C CATEGORY F-A, Supports INSERVICE INSPECTION PLAN MANAGEMENT Inservlce Inspection Database Management System Plan Report Catawba 2 Page 29 r~las2 PipingSuports Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS F01.021.011 2-R-CF-1654 CN-2491-CF020 QAL-14 VT-3 NA 6.000 Rigid Restraint CF CN-ISIN3-2591-1.1 0.000 Class B F01.021.061 2-R-NI-1619 CN-2491-NI008 OAL-14 VT-3 NA 6.000 Rigid Restraint NI CN-ISIN3-2562-1.3 0.000 Class B F01.021.062 2-R-NI-1620 CN-2491-NI008 QAL-14 VT-3 NA 6.000 Rigid Restraint NI CN-ISIN3-2562-1.3 0.000 Class B F01.021.091 2-R-NS-1208 CN-2491-NS002 QAL-14 VT-3 NA 8.000 Rigid Restraint NS CN-ISIN3-2563-1.0 0.000 Class B F01.021.092 2-R-NS-1209 CN-2491-NS002 OAL-14 VT-3 NA 8.000 Rigid Restraint NS CN-ISIN3-2563-1.0 0.000 Class B F01.021.093 2-R-NS-1211 CN-2491-NS002 QAL-14 VT-3 NA 8.000 Rigid Restraint NS CN-ISIN3-2563-1.0 0.000 Class B F01.021.094 2-R-NS-1203 CN-2491-NS003 QAL-14 VT-3 NA 8.000 Rigid Restraint NS CN-ISIN3-2563-1.0 0.000 Class B F01.021.095 2-R-NS-1204 CN-2491-NS003 QAL-14 VT-3 NA 8.000 Rigid Restraint NS CN-ISIN3-2563-1.0 0.000 Class B F01.021.141 2-R-NV-1 121 CN-2491-NVO31 QAL-14 VT-3 NA 2.000 Rigid Restraint NV CN-ISIN3-2554-1.5 0.000 Class B

EOCI14(

CAEORY FASuports DUKE ENER4? C;ORPORATION (

INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report M~ass2 PipLirngSports Catawba 2 Page 30 Inservice Inspection Plan for Interval 3 Outage I 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS F01.021.142 2-R-NVo1126 CN-2491-NVO31 QAL-14 VT-3 NA 2.000 Rigid Restraint NV CN-ISIN3-2554-1.5 0.000 Class B F01.021.143 2-R-NV-1 127 CN-2491-NVO31 OAL-14 VT-3 NA 2.000 Rigid Restraint NV CN-ISIN3-2554-1.5 0.000 Class B F01.021.144 2-R-NV-1131 CN-2491-NV032 QAL-14 VT-3 NA 2.000 Rigid Restraint NV CN-ISIN3-2554-1.5 0.000 Class B F01.021.145 2-R-NV-1 132 CN-2491-NV032 OAL-14 VT-3 NA 2.000 Rigid Restraint NV CN-ISIN3-2554-1.5 0.000 Class B F01.021.146 2-R-NV-1133 CN-2491 -NV032 QAL-14 VT-3 NA 2.000 Rigid Restraint NV CN-ISIN3-2554-1.5 0.000 Class B Total F01.021 items: 14

• • • • Category C, Thermal Movement F01.022.001 2-R-CA-1623 CN-2491-CA.00-001 QAL-14 VT-3 NA 6.000 Spring Hgr CA CN-ISIN3-2592-1.1 0.000 Class B F01.022.031 2-R-ND-0017 CN-2492-ND006 QAL-14 VT-3 NA 8.000 Spring Hgr ND CN-ISIN3-2561-1.0 0.000 Class B F01.022.032 2-R-ND-0025 CN-2492-ND006 QAL-14 VT-3 NA 8.000 Spring Hgr ND CN-ISIN3-2561-1.0 0.000 Class B Total F01.022 Items: 3

EOC 14 DUKE ENERG( CORPORATION C

CATEGORY F-A. Supports INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 31 06/20/2006 Inservice Inspection Plan for Interval 3 Outage 1 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS

• • • • Category A, One-DIrectional F01.030.051 2-R-KC-1668 CN-2491-KC140 QAL-14 VT-3 NA 6.000 Rigid Support KC CN-ISIN3-2573-1.4 0.000 Class C F01.030.052 2-R-KC-1670 CN-2491-KC140 OAL-14 VT-3 NA 6.000 Rigid Support KC CN-ISIN3-2573-1.4 0.000 Class C F01.030.053 2-R-KC-1671 CN-2491-KC140 QAL-14 VT-3 NA 6.000 Rigid Support KC CN-ISIN3-2573-1.4 0.000 Class C F01.030.054 2-R-KC-1672 CN-2491-KC140 QAL-14 VT-3 NA 6.000 Rigid Support KC CN-ISIN3-2573-1.4 0.000 Class C F01.030.055 2-R-KC-1673 CN-2491-KC140 QAL-14 VT-3 NA 6.000 Rigid Support KC CN-ISIN3-2573-1.4 0.000 Class C F01 .030.056 2-R-KC-1641 CN-2491-KC142 QAL-14 VT-3 NA 6.000 Rigid Support KC CN-ISIN3-2573-1.7 0.000 Class C F01.030.057 2-R-KC-1632 CN-2491-KC144 QAL-14 VT-3 NA 8.000 Rigid Support KC CN-ISIN3-2573-1.7 0.000 Class C F01.030.058 2-R-KC-1630 CN-2491-KC145 QAL-14 VT-3 NA 8.000 Rigid Support KC CN-ISIN3-2573-1.3 0.000 Class C

EOC 14(

DUKE ENERk' CORPORATION C CATEORY F-ALI~rs INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 32 M~!is3 PipingSuports Inservice Inspection Plan for Interval 3 Outage 1 06420/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS F01.030.101 2-R-KD-0086 CN-2493-KDO01 QAL-14 VT-3 NA 8.000 Rigid Support KD CN-ISIN3-2609-1.0 0.000 Class C Total F101.030 Items: 9

• • • • Category B, Multi-Directional F01.031.051 2-R-KC-1665 CN-2491-KC140 QAL-14 VT-3 NA 6.000 Rigid Restraint KC CN-ISIN3-2573-1.4 0.000 Class C F01.031.052 2-R-KC-1666 CN-2491-KC140 OAL-14 VT-3 NA 6.000 Rigid Restraint KC CN-ISIN3-2573-1.4 0.000 Class C F01.031.121 2-R-LD-0007 CN-2493-LD032 OAL-14 VT-3 NA 6.000 Rigid Restraint LD CN-ISIN3-2609-2.0 0.000 Class C F01.031.221 2-R-VN-0058 CN-2493-VN002 QAL-14 VT-3 NA 30.000 Rigid Restraint VN CN-ISIN3-2609-5.0 0.000 Class C Total F01.031 items: 4 Category C, Thermal Movement F01.032.051 2-R-KC-0001 CN-2492-KC073 OAL-14 VT-3 NA 16.000 Inspect with D101.020.012.

Spring Hgr KC CN-ISIN3-2573-2.0 0.750 Class C F01.032.052 2-R-KC-0054 CN-2492-KC095 OAL-14 VT-3 NA 16.000 Inspect with D01.020.013.

Spring Hgr KC CNolSIN3-2573-2.1 0.750 Class C

EOC 14 ( (

DUKE ENERGC ,;ORPORATION CATEGORY F-A .Supports INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 33 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS F01.032.053 2-R-KC-0227 CN-2492-KC1 18 GAL-14 VT-3 NA 14.000 Inspect with D01.020.011.

Mech Snubber KC CN-ISIN3-2573-1.2 0.625 Class C F01.032.101 2-R-KD-0081 CN-2493-KDO02 QAL-14 VT-3 NA 8.000 Spring Hgr KD CN-ISIN3-2609-1.0 0.000 Class C F01.032.102 2-R-KD-0084 CN-2493-KDO02 GAL-14 VT-3 NA 8.000 Mech Snubber KD CN-ISIN3-2609-1.0 0.000 Class C F01.032.121 2-R-LD-0018 CN-2493-LD001 OAL-14 VT-3 NA 6.000 Spring Hgr LD CN-ISIN3-2609-2.2 0.000 Class C Total F01.032 Items: 6

EOC 14 CATEGORY F-A, Supports DUKE ENER4? ,;ORPORATION (-

INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report E urts OtherihanPiinSuorts Catawba 2 Page 34 M Inservice Inspection Plan for Interval 3 Outage 1 06/20f2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS

• • • • Class 1, 2, and 3 ****

F01.040.005 2RCPA-SUPPORT CN-1070-8 QAL-14 VT-3 NA 0.000 Reactor Coolant Pump 2A Lateral Support.

Rigid Support NC CN-ISIN3-2553-1.0 0.000 Class A F01.040.202 2KFPA-SUPPORT CNM 2201.05-15 OAL-14 VT-3 NA 0.000 Fuel Pool Cooling Pump 2A Support (2 Angle Beam Rigid Support KC CN-ISIN3-2570-1.0 0.000 Brace Supports).

Class C F01.040.203 2KFHXA-SUPPORT CNM 1201.06-54 OAL-14 VT-3 NA 0.000 Fuel Pool Cooling Heat Rigid Support KC CN-ISIN3-2570-1.0 0.000 Exchanger 2A Support (2 Saddle Supports).

Class C Total F01.040 Items: 3 Total F01 Items: 62

EOC 14 ( C DUKE ENERCI CORPORATION CATEGORY AUG. Augmented Inspections INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspecton Database Management System Plan Report Catawba 2 Page 35 Inservice Inspection Plan for Interval 3 Outage I 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS G02.001.023 2SM51-06 CN-2SM-051 NDE-600 UT CS 34.000 Component SM CN-ISIN3-2593-1.0 2.375 Class B G02.001.023A 2SM51-06 CN-2SM-051 NDE-25 MT CS 34.000 SM CN-ISIN3-2593-1.0 2.375 Class B G02.001.024 2SM51-05 CN-2SM-051 NDE-600 UT CS 34.000 Component SM CN-ISIN3-2593-1.0 2.375 Class B G02.001.024A 2SM51-05 CN-2SM-051 NDE-25 MT CS 34.000 SM CN-ISIN3-2593-1.0 2.375 Class B G02.001.025 2SM-7C-A CN-2SM-051 NDE-600 UT CS 34.000 Component Grinnell Piece Mark CW-SM-7C Weld A.

SM CN-ISIN3-2593-1.0 2.375 Class B G02.0011.025A 2SM-7C-A CN-2SM-051 NDE-25 MT CS 34.000 Grinnell Piece Mark CW-SM-7C Weld A SM CN-ISIN3-2593-1.0 2.375 Class B G02.001.026 2SM51-07 CN-2SM-051 NDE-600 UT CS 34.000 Component SM CN-ISIN3-2593-1.0 2.375 Class B G02.001.026A 2SM51-07 CN-2SM-051 NDE-25 MT CS 34.000 SM CN-ISIN3-2593-1.0 2.375 Class B

EOC 14 ( DUKE ENER&, q.ORPORATION C CATEGORY AUG. Augmented Inspections INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 36 Inservice Inspection Plan for Interval 3 Outage 1 06/20/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIAITHK CAL BLOCKS COMMENTS G02.001.027 2SM-6C-A CN-2SM-051 NDE-600 UT CS 34.000 Component Grinnell Piece Mark CW-SM-6C Weld A. Procedure SM CN-ISIN3-2593-1.0 PDI-UT-1 1.750 PDI-UT-1-C NDE-600 uses the component for calibration.

Class B Procedure PDI-UT-1 may be used in lieu of NDE-600. If PDI-UT-1 is used, then the calibration block listed shall be used.

G02.001.027A 2SM-6C-A CN-2SM-051 NDE-25 MT CS 34.000 Grinnell Piece Mark CW-SM-6C Weld A SM CN-ISIN3-2593-1.0 1.750 Class B G02.001.028 2SM54-03 CN-2SM-054 NDE-600 UT CS 34.000 Component Procedure NDE-600 uses the component for SM CN-ISIN3-2593-1.0 PDI-UT-1 1.750 PDI-UT-1-C calibration. Procedure PDI-UT-1 may be used in lieu Class B of NDE-600. If PDI-UT-1 is used, then the calibration block listed shall be used.

G02.001.028A 2SM54-03 CN-2SM-054 NDE-25 MT CS 34.000 SM CN-ISIN3-2593-1.0 1.750 Class B G02.001.029 2SM54-02 CN-2SM-054 NDE-600 UT CS 34.000 Component Procedure NDE-600 uses the component for SM CN-ISIN3-2593-1.0 PDI-UTo1 1.750 PDI-UT-1-C calibration. Procedure PDI-UT-1 may be used in lieu Class B of NDE-600. If PDI-UT-1 is used, then the calibration block listed shall be used.

G02.001.029A 2SM54-02 CN-2SM-054 NDE-25 MT CS 34.000 SM CN-ISIN3-2593-1.0 1.750 Class B G02.001.030 2SM-4C-A CN-2SM-054 NDE-600 UT CS 34.000 Component Grinnell Piece Mark CW-SM-4C Weld A. Procedure SM CN-ISIN3-2593-1.0 PDI-UT-1 1.375 PDI-UT-1-C NDE-600 uses the component for calibration.

Class B Procedure PDI-UT-1 may be used in lieu of NDE-600. If PDI-UT-1 is used, then the calibration block listed shall be used.

G02.001.030A 2SM-4C-A CN-2SM-054 NDE-25 MT CS 34.000 Grinnell Piece Mark CW-SM-4C Weld A SM CN-ISIN3-2593-1.0 1.375 Class B

EOC14 *DUKE ENER* CORPORATION CATEGORY AUG. Augmented Inspections INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report Catawba 2 Page 37 Inservice Inspection Plan for Interval 3 Outage 1 06120/2006 ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC INSP REQ MAT/SCH DIATHK CAL BLOCKS COMMENTS G02.001.031 2SM-4C-B CN-2SM-054 NDE-600 UT CS 34.000 Component Grinnell Piece Mark CW-SM-4C Weld B. Procedure SM CN-ISIN3-2593-1.0 PDI-UT-1 1.375 PDI-UT-1-C NDE-600 uses the component for calibration.

Class B Procedure PDI-UT-1 may be used in lieu of NDE-600. If PDI-UT-1 is used, then the calibration block listed shall be used.

G02.001.031A 2SM-4C-B CN-2SM-054 NDE-25 MT CS 34.000 Grinnell Piece Mark CW-SM-4C Weld B SM CN-ISIN3-2593-1.0 1.375 Class B Total G02.001 Items: 18 Total G02 Items: 18

EOC 14 DUKE ENERC CORPORATION C

CATEGORY AUG. Augmented Inspections INSERVICE INSPECTION PLAN MANAGEMENT Inservice Inspection Database Management System Plan Report IITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC Catawba 2 Inservice Inspection Plan for Interval 3 Outage 1 INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS Page 38 06/20/2006 G06.001.001 2PZR-W4ASE OAL-15 VT-2 SS-CS 6.000 Pressurizer Safety Nozzle Safe End X-Y Quadrant.

Circumferential NC CNM 2201.01-110/1 0.960 Bare Metal Visual Examination by VT-2 qualified Class A Term end CNM 2201.01-110/2 inspector around 100% of penetration. (For Dissimilar responsibile individual, contact J. M. Shuping, Alloy 600 Engineer Nuclear Technical Services).

Reference NRC Bulletin 2004-01).

Reference Item Number G08.001.003.

G06.001.002 2PZR-W4BSE CNM 2201.01-110/1 QAL-15 VT-2 SS-CS 6.000 Pressurizer Safety Nozzle To Safe End.

Circumferential NC CNM 2201.01-110/2 0.960 W-X Quadrant.

Class A Term end Nozzle to Bare Metal Visual Examination by VT-2 qualified Dissimilar Safe End inspector around 100% of penetration. (For responsibile individual, contact J. M. Shuping, Alloy 600 Engineer Nuclear Technical Services).

Reference NRC Bulletin 2004-01).

Reference Item Number G08.001.004.

G06.001.003 2PZR-W4CSE CNM 2201.01-110/1 QAL-15 VT-2 SS-CS 6.000 Pressurizer Relief Nozzle To Safe End.

Circumferential NC CNM 2201.01-110/2 0.960 W-Z Quadrant.

Class A Term end Nozzle to Bare Metal Visual Examination by VT-2 qualified Dissimilar Safe End Inspector around 100% of penetration. (For responsibile individual, contact J. M. Shuping, Alloy 600 Engineer Nuclear Technical Services).

Reference NRC Bulletin 2004-01).

Reference Item Number G08.001.005.

G06.001.004 2PZR-W3SE CNM 2201.01-110/1 QAL-15 VT-2 SS-CS 6.000 Pressurizer Safety Nozzle To Safe End. Y-Z Circumferential NC CNM 2201.01-110/2

• 0.960 Quadrant.

Class A Term end Nozzle to Bare Metal Visual Examination by VT-2 qualified Dissimilar Safe End inspector around 100% of penetration. (For responsibile individual, contact J. M. Shuping, Alloy 600 Engineer Nuclear Technical Services).

Reference NRC Bulletin 2004-01).

Reference Item Number G08.001.002.

G06.001.005 2PZR-WISE CNM 2201.01-110/1 QAL-15 VT-2 SS-CS 14.000 Pressurizer Surge Nozzle To Safe End.

Circumferential NC CNM 2201.01-110/2 1.640 Bare Metal Visual Examination by VT-2 qualified Class A Term end Nozzle to inspector around 100% of penetration. (For Dissimilar Safe End responsibile individual, contact J. M. Shuping, Alloy 600 Engineer Nuclear Technical Services).

Reference NRC Bulletin 2004-01).

(

EOC 14 CATEGORY AUG. Auamented InRn~etirmn* DUKE ENERC CORPORATION INSERVICE INSPECTION PLAN MANAGEMENT C

CA EGO Y A G AunmentedInsnpctions Inservice Inspection Database Management System Plan Report I

ITEM NUMBER ID NUMBER SYS ISO/DWG NUMBERS PROC Catawba 2 Inservice Inspection Plan for Interval 3 Outage 1 INSP REQ MAT/SCH DIA/THK CAL BLOCKS COMMENTS Page 39 06/2012006 Reference Item Number G08.001.001.

G06.001.006 2PZR-W2SE CNM 2201.01-110/1 QAL-15 VT-2 SS-CS 4.000 Pressurizer Spray Nozzle To Safe End.

Circumferential NC CNM 2201.01-110/2 0.760 Bare Metal Visual Examination by VT-2 qualified Class A Term end Nozzle to Inspector around 100% of penetration. (For Dissimilar Safe End responsibile individual, contact J. M. Shuping, Alloy 600 Engineer Nuclear Technical Services).

Reference NRC Bulletin 2004-01).

Reference Item Number G08.001.006.

Total GO6.001 Items: 6 G06.002.001 2PZR-MANWAY CNM 2201.01-110/1 QAL-15 VT-2 NA 0.000 Pressurizer Manwav Dlanhram Seal Weld NC CNM 2201.01-110/2 0.000 Bare Metal Visual Examination by VT-2 qualified Class A Inspector. Examine the gap between the Pressurizer Manway Cover and Manway for evidence of diaphram plate seal weld leakage. (For responsibile individual, contact J. M. Shuping, Alloy 600 Engineer Nuclear Technical Services).

Reference NRC Bulletin 2004-01)

Total G06.002 items: 1 Total G06 Items: 7

4.0 Results Of Inspections Performed The results of each examination shown in the final Inservice Inspection Plan (Section 3.0 of this report) are included in this section. The completion date and status for each examination are shown. All examinations revealing reportable indications and any corrective action required as a result are described in further detail in Subsections 4.1 and 4.2. Corrective measures performed and limited examinations are described in further detail in Subsections 4.3 and 4.4.

The information shown below is a field description for the reporting format included in this section of the report.

ITEM NUMBER = ASME Section Xl Tables IWB-2500-1 (Class 1), IWC-2500-1 (Class 2), IWF-2500-1 (Class 1 and Class 2),

Augmented / Elective Requirements ID NUMBER = Unique Identification Number SYSTEM = Component System Identification INSP DATE = Date of Examination INSP STATUS = CLR Clear REC Recordable REP Reportable INSP LIMITED = Indicates inspection was limited.

Coverage obtained is listed.

GEO REF = Y Yes (Geometric Reflector -- No applies only to UT)

= Y Yes RFR (Relief Request)

-- No COMMENTS = General and / or Detail Description EOC 14 Refueling Outage Report Page 1 of 2 Catawba Unit 2 Revision 0 Section 4 June 20, 2006

4.1 Reportable Indications None 4.2 Corrective Action Corrective action is action taken to resolve flaws and relevant conditions, including supplemental examinations, analytical evaluations, repair/

replacement activities, and corrective measures.

4.3 Corrective Measures Corrective measures are actions (such as maintenance) taken to resolve relevant conditions, but not including supplemental examinations, analytical evaluations, and repair/ replacement activities. Any corrective measures performed for examinations associated with this report period will be shown on the examination data sheets which are on file at the Duke Energy Corporate Office in Charlotte, North Carolina.

4.4 Limited Examinations Limitations (i.e. 90% or less of the required examination coverage obtained) identified for examinations associated with this report period are shown below. A relief request will be submitted to seek NRC acceptance of the limited coverage. This information will be on file at The Duke Energy Corporate Office in Charlotte, North Carolina. Reference Subsection 1.3 for additional information.

A request for relief for non-code inspections (item Number G02.001.030A in this report) are not required to be submitted.

Item Number Relief Reauest Serial Numbers B09.011.165 To be filed later B09.011.171 To be filed later C05.021.209 To be filed later EOC 14 Refueling Outage Report Page 2 of 2 Catawba Unit 2 Revision 0 Section 4 June 20, 2006

DUKE ENERGY CORPORATION QUALITY ASSURANCFTECHNICAL SERVICES Run D EOC14 1 Plant: Catawba 2 In-Service Inspection D( ase Management System Catawba 2 Inservice Inspection Usting C Page 1 07/11/2006 Interval 3 Outage 1 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS B06.010.001 2RPV-179-102-01 NC 03/26/2006 CLR - N N B06.010.002 2RPV-179-102-02A NC 03/26/2006 CLR -- N N B06.010.003 2RPV-179-102-03 NC 03/26/2006 CLR - N N 806.010.004 2RPV-179-102-04 NC 03/26/2006 CLR - N N B06.010.005 2RPV-179-102-05A NC 03/26/2006 CLR - N N B06.010.006 2RPV-179-102-Si NC 03/26/2006 CLR - N N B06.010.007 2RPV-179-102-07 NC 03/28/2006 CLR -- N N B06.010.008 2RPV-179-102-08A NC 03/28/2006 CLR --- N N B06.010.009 2RPV-179-102-09A NC 03/28/2006 CLR --- N N B06.010.010 2RPV-179-102-10 NC 03/28/2006 CLR --- N N B06.010.011 2RPV-179-102-11 NC 03/28/2006 CLR --- N N B06.010.012 2RPV-179-102-12 NC 03/28/2006 CLR -- N N B06.010.013 2RPV-179-102-13A NC 03/27/2006 CLR --- N N B06.010.014 2RPV-179-102-14 NC 03/27/2006 CLR - N N B06.010.015 2RPV-179-102-15 NC 03/27/2006 CLR -- N N B06.010.016 2RPV-179-102-16 NC 03/27/2006 CLR - N N B06.010.017 2RPV-179-102-17 NC 03/27/2006 CLR - N N B06.010.018 2RPV-179-102-18 NC 03/27/2006 CLR - N N B06.030.001 2RPV-179-101-01 NC 03/27/2006 CLR - N N B06.030.002 2RPV-179-101-02A NC 03/27/2006 CLR - N N B06.030.003 2RPV-179-101-03 NC 03127/2006 CLR -- N N B06.030.004 2RPV-179-101-04 NC 03/27/2006 CLR - N N B06.030.005 2RPV-179-101-05A NC 03/27/2006 CLR - N N B06.030.006 2RPV-179-101-Si NC 03/27/2006 CLR - N N B06.030.007 2RPV-179-101-07 NC 03/27/2006 CLR - N N B06.030.008 2RPV-179-101-08 NC 03/27/2006 CLR --- N N B06.030.009 2RPV-179-101-09 NC 03/27/2006 CLR - N N B06.030.010 2RPV-179-101-10 NC 03/27/2006 CLR - N N B06.030.011 2RPV-179-101-11 NC 03/27/2006 CLR - N N B06.030.012 2RPV-179-101-12 NC 03/27/2006 CLR - N N B06.030.013 2RPV-179-101-13 NC 03/27/2006 CLR - N N B06.030.014 2RPV-179-101-14 NC 03/27/2006 CLR -- N N B06.030.015 2RPV-179-101-15 NC- 03/27/2006 CLR -- N N 806.030.016 2RPV-179-101-16 NC 03/27/2006 CLR - N N B06.030.017 2RPV-179-101-17 NC 03/27/2006 CLR -- N N B06.030.018 2RPV-179-101-18 NC 03/2712006 CLR - N N B06.050.001 2RPV-179-103-01 NC 03/26/2006 CLR - N N

DUKE ENERGY CORPORATION QUALITY ASSURANCI- TECHNICAL SERVICES EOC 14 ( In-Service Inspection Dk ase Management System Catawba 2 Inservice Inspection Listing

( Run D Page 2 Plant: Catawba 2 07/11/2006 Interval 3 Outage 1 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS B06.050.002 2RPV-179-103-02A NC 03/26/2006 CLR - N N B06.050.003 2RPV-179-103-03 NC 03/26/2006 CLR -- N N B06.050.004 2RPV-179-103-04 NC 03/26/2006 CLR -- N N B06.050.005 2RPV-179-103-05A NC 03/26/2006 CLR - N N B06.050.006 2RPV-179-103-Si NC 03/26/2006 CLR - N N B06.050.007 2RPV-179-103-07 NC 03/26/2006 CLR - N N B06.050.008 2RPV-179-103-08 NC 03/28/2006 CLR - N N B06.050.009 2RPV-179-103-09 NC 03/28/2006 CLR -- N N B06.050.010 2RPV-179-103-10 NC 03/28/2006 CLR -- N N B06.050.011 2RPV-179-103-11 NC 03/28/2006 CLR -- N N B06.050.012 2RPV-179-103-12 NC 03/28/2006 CLR -- N N B06.050.013 2RPV-179-103-13A NC 03/27/2006 CLR -- N N B06.050.014 2RPV-179-103-14 NC 03/27/2006 CLR - N N B06.050.015 2RPV-179-103-15 NC 03/27/2006 CLR --- N N B06.050.016 2RPV-179-103-16 NC 03/27/2006 CLR - N N B06.050.017 2RPV-179-103-17 NC 03/27/2006 CLR - N N B06.050.018 2RPV-179-103-18 NC 03/27/2006 CLR - N N B09.011.032 2NC24-11 NC 03/20/2006 CLR -- N N 609.011 .032A 2NC24-11 NC 03/20/2006 CLR --- N N B09.011.033 2NC24-17 NC 03/20/2006 CLR -- N N B09.011.033A 2NC24-17 NC 03/20/2006 CLR -- N N B09.011.034 2NC24-7 NC 03/20/2006 CLR - N N B09.011.034A 2NC24-7 NC 03/20/2006 CLR - N N B09.011.035 2NC24-8 NC 03/20/2006 CLR -- N N B09.011.035A 2NC24-8 NC 03/20/2006 CLR -- N N B09.011.165 2NI55-11 NI 03/23/2006 CLR 37.50% N Y Request for Relief will be Filed.

B09.011.165A 2NI55-11 NI 03/23/2006 CLR --- N N B09.011.166 2NI55-12 NI 03/23/2006 bLR - N N B09.011.166A 2NI55-12 NI 03/23/2006 CLR - N N B09.011.167 2NI55-14 NI 03/28/2006 CLR -- N N B09.011.167A 2NI55-14 NI 03/22/2006 CLR - N N B09.011.168 2NI55-2 NI 03/23/2006 CLR -- N N B09.011.168A 2NI55-2 NI 03/22/2006 CLR - N N B09.011.169 2NI55-4 NI 03/23/2006 CLR - N N B09.011.169A 2NI55-4 NI 03/22/2006 CLR -- N N B09.011.170 2NI55-6 NI 03/23/2006 CLR - Y N B09.011.170A 2NI55-6 NI 03/23/2006 CLR -- N N

DUKE ENERGY CORPORATION QUALITY ASSURANCF TECHNICAL SERVICES Run D EOC 14 ( In-Service Inspection D( ase Management System Catawba 2 Inservice Inspection Listing Page 3 07/11/2006 Plant: Catawba 2 Interval 3 Outage 1 ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS B09.011.171 2NI55-8 NI 03/23/2006 CLR 62.50% Y Request for Relief will be Filed.

B09.011.171A 2NI55-8 NI 03/23/2006 CLR N B09.040.006 2NC44-27 NC 03/23/2006 CLR N B09.040.127 2NV323-10 NV 03/26/2006 CLR N B09.040.128 2NV323-11 NV 03/26/2006 CLR N B09.040.129 2NV323-12 NV 03/26/2006 CLR N B09.040.130 2NV323-16 NV 03/26/2006 CLR N B09.040.131 2NV323-18 NV 03/26/2006 CLR N B09.040.132 2NV323-19 NV 03/26/2006 CLR N B09.040.133 2NV323-20 NV 03/26/2006 CLR N B09.040.134 2NV323-22 NV 03/26/2006 CLR N B09.040.135 2NV323-25 NV 03/26/2006 CLR N B09.040.136 2NV323-26 NV 03/26/2006 CLR N C05.011.008 2CA153-49 CA 04/06/2006 CLR N C05.011.008A 2CA1 53-49 CA 04/08/2006 CLR N C05.011.009 2CA153-50 CA 04/08/2006 CLR N C05.011.009A 2CA153-50 CA 04/08/2006 CLR N C05.011.101 2FW76-1 FW 03/07/2006 CLR N C05.01 1.101 A 2FW76-1 FW 03/07/2006 CLR N C05.011.164 2ND2-1 ND 03/14/2006 CLR N C05.011.164A 2ND2-1 ND 03/14/2006 CLR N C05.011.165 2ND2-10 ND 03/14/2006 CLR N C05.011.165A 2ND2-10 ND 03/14/2006 CLR N C05.011.166 2ND2-11 ND 03/14/2006 CLR N C05.011.166A 2ND2-11 ND 03/14/2006 CLR N C05.011.167 2ND2-2 ND 03/14/2006 CLR N C05.011.167A 2ND2-2 ND 03/14/2006 CLR N C05.011.168 2ND2-3 ND 03/14/2006 CLR N C05.011.168A 2ND2-3 NO 03/14/2006 CLR N C05.011.169 2ND2-9 ND 03/14/2006 CLR N C05.011.169A 2ND2-9 ND 03/14/2006 CLR N C05.021.201 2NV104-1 NV 03/03/2006 CLR N C05.021.201A 2NV104-1 NV 03/03/2006 CLR N C05.021.202 2NV104-2 NV 03/03/2006 CLR N C05.021.202A 2NV104-2 NV 03/03/2006 CLR N C05.021.203 2NVI1-16 NV 03/01/2006 CLR N C05.021.203A 2NV11-16 NV 03/01/2006 CLR N

DUKE ENERGY CORPORATION QUALITY ASSURAN9'" TECHNICAL SERVICES EOC 14 ( In-Service Inspection D4 jase Management System Catawba 2 Inservice Inspection Listing

( Run D Page 4 Plant: Catawba 2 07/11/2006 Interval 3 Outage I ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS C05.021.204 2NV11-18 NV 03/02/2006 CLR - N N C05.021.204A 2NV11-18 NV 03/02/2006 CLR - N N C05.021.205 2NV1 1-20 NV 03/01/2006 CLR -- N N C05.021.205A 2NV1 1-20 NV 03/01/2006 CLR -- N N C05.021.206 2NV1 1-21 NV 03/01/2006 CLR -- N N C05.021.206A 2NV1 1-21 NV 03/01/2006 CLR -- N N C05.021.207 2NV1 1-7 NV 03/01/2006 CLR 92.00% N N C05.021.207A 2NVl 1-7 NV 03/01/2006 CLR -- N N C05.021.208 2NV1 1-8 NV 03/01/2006 CLR 92.00% N N C05.021.208A 2NV11-8 NV 03/01/2006 CLR -- N N C05.021.209 2NV12-10 NV 03/02/2006 CLR 78.70% N Y Request for Relief will be Filed C05.021.209A 2NV12-10 NV 03/01/2006 CLR - N N C05.021.210 2NV12-11 NV 03/01/2006 CLR -- N N C05.021.210A 2NV12-11 NV 03/01/2006 CLR --- N N C05.030.108 2NV242-10 NV 03/27/2006 CLR - N N C05.030.109 2NV242-11 NV 03/27/2006 CLR -- N N C05.030.110 2NV242-3 NV 03/27/2006 CLR - N N C05.030.111 2NV242-4 NV 03/27/2006 CLR - N N C05.041.031 2NI100-9 NI 03/07/2006 CLR -- N N C05.051.001 2CA59-11 CA 03/31/2006 CLR - Y N C05.051.001A 2CA59-11 CA 03/31/2006 CLR -- N N C05.051.002 2CA59-8 CA 03/31/2006 CLR -- Y N C05.051.002A 2CA59-8 CA 03/31/2006 CLR - N N C05.051.155 2SV8-2 SV 04/05/2006 CLR - N N C05.051.155A 2SV8-2 SV 04/05/2006 CLR - N N C06.020.018 2SV-2 SV 04/07/2006 CLR --. N N D01.020.011 2-R-KC-0227 KC 10/17/2005 CLR - N N D01.020.012 2-R-KC-0001 KC 10/20/2005 CLR - N N D01.020.013 2-R-KC-0054 KC 11/02/2005 CLR - N N F01.010.001 2-R-NC-1022 NC 03/21/2006 CLR - N N F01.010.002 2-R-NC-1024 NC 03/21/2006 CLR - N N F01.011.051 2-R-NI-1759 NI 03/21/2006 CLR - N N F01.011.052 2-R-NI-1761 NI 03/21/2006 CLR - N N F01.012.001 2-R-NC-1028 NC 03/21/2006 CLR - N N F01.012.051 2-R-NI-1086 NI 03/21/2006 CLR - N N F01.012.052 2-R-NI-1762 NI 03/21/2006 CLR - N N F01.020.001 2-R-CA-1614 CA 03/20/2006 CLR - N N

DUKE ENERGY CORPORATION QUALITY ASSURANCE: TECHNICAL SERVICES EOC 14 I-evc Inspection ~ jase npcin -1In-Service aaeetSse SystemunD s Management Page 5 Inservice Catawba 2Interval 3 Outage I usting Inspection 07/11/2005 ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS ITEM NUMBER 2-R-CA-1620 CA 03/20/2006 CLR - N N F01.020.002 F01.020.003 2-R-CA-1622 CA 03/20/2006 CLR - N N F01.020.021 2-R-FW-01 16 FW 10/17/2005 CLR -- N N F01.020.031 2-R-ND-0319 ND 11/08/2005 CLR ... N N F01.020.032 2-R-ND-0321 ND 11/08/2005 CLR -- N N F01.020.033 2-R-ND-0323 ND 11/08/2005 REC - N N 2-R-NI-1769 NI 03/21/2006 CLR - N N F01.020.061 F01.020.062 2-R-NI-1770 NI 03/21/2006 CLR .-- N N F01.020.063 2-R-NI-1623 NI 03/21/2006 CLR --- N N F01.020.091 2-R-NS-1220 NS 03/20/2006 CLR -- N N F01.020.092 2-R-NS-1221 NS 03/20/2006 CLR - N N F01.020.093 2-R-NS-1250 NS 03/20/2006 CLR -- N N 2-R-NV-1170 NV 03/21/2006 CLR .-- N N F01.020.141 F01.020.142 2-R-NV-1171 NV 03/21/2006 CLR - N N F01.020.143 2-R-NV-1172 NV 03/21/2006 CLR --- N N F01.021.011 2-R-CF-1654 CF 03/20/2006 CLR .-- N N F01.021.061 2-R-NI-1619 NI 03/21/2006 CLR - N N F01.021.062 2-R-NI-1620 NI 03/21/2006 CLR - N N F01.021.091 2-R-NS-1208 NS 03/20/2006 REC -- N N F01.021.092 2-R-NS-1209 NS 03/20/2006 CLR -- N N 2-R-NS-1211 NS 03/20/2006 CLR N N F01.021.093 -

F01.021.094 2-R-NS-1203 NS 03/20/2006 CLR -- N N F01.021.095 2-R-NS-1204 NS 03/20/2006 CLR -- N N F01.021.141 2-R-NV-1121 NV 03/21/2006 CLR -- N N F01.021.142 2-R-NV-1 126 NV 03/21/2006 CLR - N N F01.021.143 2-R-NV-1127 NV 03/21/2006 CLR - N N F01.021.144 2-R-NV-1131 NV 03/21/2006 CLR -- N N F01.021.145 2-R-NV-1132 NV 03/21/2006 CLR - N N F01.021.146 2-R-NV-1133 NV 03/21/2006 CLR .-- N N F01.022.001 2-R-CA-1623 CA 03/20/2006 CLR - N N F01.022.031 2-R-ND-0017 ND 10/17/2005 CLR - N N F01.022.032 2-R-ND-0025 ND 10/17/2005 CLR --. N N F01.030.051 2-R-KC-1668 KC 03/21/2006 CLR -- N N P01.030.052 2-R-KC-1670 KC 03/21/2006 CLR - N N 2-R-KC-1671 KC 03/21/2006 CLR - N N F01.030.053 2-R-KC-1672 KC 03/21/2006 CLR - N N F01.030.054 F01.030.055 2-R-KC-1673 KC 03/21/2006 CLR - N N

DUKE ENERGY CORPORATION QUALITY ASSURAN9- TECHNICAL SERVICES EOC 14 ( In-ServIce Inspection D1, )ase Management System Catawba 2 Inservlce Inspection Listing

( Run D Page 6 Plant: Catawba 2 07/11/2006 Interval 3 Outage I ITEM NUMBER ID NUMBER SYSTEM INSP DATE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS F01.030.056 2-R-KC-1 641 KC 03/21/2006 CLR - N N F01.030.057 2-R-KC-1632 KC 03/21/2006 CLR --- N N F01.030.058 2-R-KC-1630 KC 03/21/2006 CLR - N N F01.030.101 2-R-KD-0086 KD 11/02/2005 CLR - N N F01.031.051 2-R-KC-1665 KC 03/21/2006 CLR - N N F01.031.052 2-R-KC-1666 KC 03/21/2006 CLR -- N N F01.031.121 2-R-LD-0007 LD 10/17/2005 CLR - N N F01.031.221 2-R-VN-0058 VN 10/17/2005 CLR -- N N F01.032.051 2-R-KC-0001 KC 10/20/2005 CLR - N N F01.032.052 2-R-KC-0054 KC 11/02/2005 CLR - N N F01.032.053 2-R-KC-0227 KC 10/17/2005 CLR -- N N F01.032.101 2-R-KD-0081 KD 11/02/2005 CLR - N N F01.032.102 2-R-KD-0084 KD 11/02/2005 CLR -- N N F01.032.121 2-R-LD-0018 LD 11/02/2005 CLR -- N N F01.040.005 2RCPA-SUPPORT NC 03/20/2006 CLR - N N F01.040.202 2KFPA-SUPPORT KC 10/20/2005 CLR - N N F01.040.203 2KFHXA-SUPPORT KC 10/24/2005 CLR -- N N G02.001.023 2SM51-06 SM 04/08/2006 CLR - N N G02.001.023A 2SM51-06 SM 04/07/2006 CLR -- N N G02.001.024 2SM51-05 SM 04/08/2006 CLR -- N N G02.001.024A 2SM51-05 SM 04/07/2006 CLR - N N G02.001.025 2SM-7C-A SM 04/08/2006 CLR --- N N G02.001.025A 2SM-7C-A SM 04/07/2006 CLR - N N G02.001.026 2SM51-07 SM 04/09/2006 CLR -- N N G02.001.026A 2SM51-07 SM 04/07/2006 CLR - N N G02.001.027 2SM-6C-A SM 04/09/2006 CLR - N N G02.001.027A 2SM-6C-A SM 04/07/2006 CLR -- N N G02.001.028 2SM54-03 SM 04/08/2006 CLR - N N G02.001.028A 2SM54-03 SM 04/07/2006 CLR - N N G02.001.029 2SM54-02 SM 04/08/2006 CLR - N N G02.001.029A 2SM54-02 SM 04/07/2006 CLR - N N G02.001.030 2SM-4C-A SM 04/08/2006 CLR -- N N G02.001.030A 2SM-4C-A SM 04/07/2006 CLR 73.80% N N G02.001.031 2SM-4C-B SM 04/08/2006 CLR - N N G02.001.031A 2SM-4C-B SM 04/07/2006 CLR - N N G06.001.001 2PZR-W4ASE NC 03/28/2006 CLR - N N G06.001.002 2PZR-W4BSE NC 03/28/2006 CLR - N N

DUKE ENERGY CORPORATION QUALITY ASSURAN9F TECHNICAL SERVICES In-Service Inspection I* 3ase Management System ( Run D EOC 14 Page 7 Catawba 2 Inservice Inspection Listing Plant: Catawba . 07111/2006 Interval 3 Outage 1 ITEM NUMBER ID NUMBER SYSTEM INSP D TE INSP STATUS INSP LIMITED GEO REF RFR COMMENTS G06.001.003 2PZR-W4CSE NC 03/28/2( 006 CLR - N N G06.001.004 2PZR-W3SE NC 03128/2( 06 CLR - N N G06.001.005 2PZR-W 1SE NC 04/02/2( 306 CLR - N N G06.001.006 2PZR-W2SE NC 03/28/2( 06 CLR --- N N G06.002.001 2PZR-MANWAY NC 03/28/2( 06 CLR -- N N

v._ 5.0 Owner's Report for Repair I Replacement Activities As required by the applicable code, records of Class 1 and Class 2 Repair and Replacement work is included on NIS-2 forms in this section.

The NIS-2 forms included in this section were completed for work performed during this report period.

The individual work request documents and manufacturers' data reports are on file at Catawba Nuclear Station.

EOC 14 Refueling Outage Report Page 1 of 1 Catawba Unit 2 Revision 0 Section 5 June 20, 2006

-C ( -I U Flaw I I (

Indication Code Repair, Maint/ ISI Owner Work Order Class Sys MOD No. Description of Work Replacement (*Yes No) Final ANII Final 98672243-01 B NV NA Bolting for Flange Replacement No 5/3/2006 7/14/2006 98688708-15 NF SM CN21441/00 U Bolt for 2-R-SM-1880 New No 5/10/2006 5/10/2006 98688709-15 NF SM CN21441/00 Sway Strut for 2-R-SM-1 885 New No 5/9/2006 5/10/2006 98698974-01 B SM NA Bolting for 2SM-3 Replacement No 4/18/2006 4/18/2006 98706897-03 B NS NA Valve Disc for 2NS-75 Replacement No 3/30/2006 4/15/2006 98707253-01 B NV NA Plug Assembly for 2NV-309 Replacement No 4/12/2006 4/12/2006 98707254-01 B NV NA Plug Assembly for 2NV-294 Replacement No 5/3/2006 5/5/2006 98709786-06 NF RN CD500175 S/R 1-R-RN-851 Replacement No 1/22/2006 2/11/2006 98709787-15 NF RN CD500175 S/R 1-R-RN-850 Replacement No 2/6/2006 2/11/2006 98711211-06 B SM NA Pressure Test Replacement No 6/12/2006 7/14/2006 98711213-06 B SM NA Pressure Test Replacement No 6/12/2006 7/14/2006 98717037-01 B ND NA Valve Disc for 2ND24A Replacement No 4/10/2006 4/15/2006 98717523-15 NF NS NSM21448 Install NS supports Replacement No 5/11/2006 7/13/2006 98718428-15 NF RN NA Bolting for S/R 2-R-RN-288 Replacement No 4/6/2006 4/15/2006 98726106-15 B CF NA 2" CF Piping Replacement No 5/4/2006 5/5/2006 98728898-01 A NI NA Seal Weld Valve 2NI-351 Repair No 4/3/2006 4/4/2006 98728899-01 A NI NA Seal Weld Valve 2N1-015 Repair No 4/3/2006 4/4/2006 98731479-22 B CA CD200323 Relocate Valve 2CA57 Replacement No 5/31/2006 7/14/2006 98731479-33 NF CA CD200323 Relocate valve 2CA-57 Replacement No 5/11/2006 7/14/2006 98731480-15 B CA CD200323 Relocate Valve 2CA61 Replacement No 5/31/2006 7/14/2006 98731480-31 NF CA CD200323 S/R 2-R-CA-1 696 Replacement No 5/4/2006 5/5/2006 98731786-04 NF RN CD500063 S/R 2-R-RN-359 Replacement No 1/22/2006 2/11/2006 98733767-01 B NV NA Plug Assembly for 2NV-849 Replacement No 5/3/2006 5/5/2006 98734295-14 NF RN CD200108 Modify S/R 2-R-RN-365 Replacement No 3/30/2006 4/13/2006 98734297-07 NF NW NA U Bolt for 2-P-NW-5013 Replacement No 4/10/2006 4/12/2006 98735045-04 A NC NA S/R 2-R-NC-1 675 Replacement No 5/4/2006 5/4/2006 98735045-05 A NC NA Valve 2NC-002 Replacement No 5/3/2006 5/9/2006 98735046-05 A NC NA Valve 2NC-003 Replacement No 5/3/2006 5/9/2006 98735058-01 B CF NA Disc for Valve 2CF-1 66 Replacement No 4/11/2006 4/12/2006 98735059-01 B CF NA Disc for Valve 2CF-1 69 Replacement No 4/11/2006 4/12/2006 98735101-01 B SV NA Valve Disc for 2SV-3 Replacement No 4/5/2006 4/15/2006 98735103-01 B SV NA Valve Disc for 2SV-5 Replacement No 4/5/2006 4/15/2006 98735104-01 B SV NA Valve Disc for 2SV-20 Replacement No 4/5/2006 4/15/2006 98735105-01 B SV NA Valve Disc for 2SV-22 Replacement No 4/6/2006 4/15/2006 98735107-01 B SV NA Disc for Valve 2SV-24 Replacement No 4/11/2006 4/12/2006 98735717-02 NF CF NA Replace S/R 2-R-CF-1002 Replacement No 3/30/2006 4/15/2006 98735717-14 NF NV NA Replace S/R 2-R-NV-1 905 Replacement No 3/30/2006 4/1/2006 98735718-10 NF FW NA Repair S/R 2-R-FW-0003 Repair No 3/30/2006 4/1/2006 98735718-12 NF KC NA S/R 2-R-KC-0541 Replacement No 4/10/2006 4/15/2006

"98i(ij7374-02 B NW CD200358

(-

Install 2" NW 2A Dioina

-r New y -

No Y-------

4/18/2006 7/14/2006

(

98737374--26 NF NW CD200358 Supports for NW piping New No 4/20/2006 7/14/2006 98737375-02 B NW CD200358 Install 2" NW 2B piping New No 4/18/2006 7/14/2006 98738962-01 B NV NA Bolting for NV Pump "2B" Conn. Replacement No 11/10/2005 11/17/2005 98742134-01 B NV NA Bolting for 2NVFE5300 Replacement No 5/3/2006 5/3/2006 98747553-01 B KC CE200500 Valve 2KC-412 Replacement No 5/3/2006 5/9/2006 98747554-01 B KC CE200500 Install valve, piping for 2KC393 Replacement No 5/11/2006 7/14/2006 98747555-01 B KC CE200500 Valve 2KV363 Replacement No 5/3/2006 5/9/2006 98747556-01 B KC CE200500 Install valve, piping for 2KC344 Replacement No 5/23/2006 7/14/2006 98759348-01 B SV NA Valve Disc for 2SV-1 2 Replacement No 3/30/2006 4/15/2006 98760045-01 B NV NA 2NV-333 Valve Disc Replacement No 3/20/2006 3/22/2006 98783351-01 A NV NA Seal Weld Valve 2NV-861 Repair No 4/3/2006 4/4/2006 98783830-01 NF CF NA Refurbish S/R 2-R-CF-1724 Repair No 4/10/2006 4/12/2006 98785424-12 B NI NA Replace valve 2N1144 Replacement No 5/3/2006 7/14/2006 98785454-08 B NI NA Bonnet for Valve 2NI009A Replacement No 5/3/2006 5/5/2006 98785886-01 B BB NA SIR 2-R-BB-1 033 Replacement No 5/4/2006 5/4/2006 98786279-02 B ND NA SIR 2-R-ND-277 Replacement No 4/18/2006 4/18/2006 98787227-07 NF NM NA S/R 2-R-NM-1414 Pivot Pin Replacement No 5/3/2006 5/3/2006

( C (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI I. n,,w DUKE POWER COMPANY la Date 5/3/06 Sheet I of I

\ddc5.,, 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. 1,,, CATAWBA NUCLEAR STATION 2a Unit I [2 '- 3 - Shared (specify Units[:] )

Atddic,., 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98672243-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B NV CNEMICAL VOLUME CONTROL SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (h) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identi fication of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number Replacement Stamped

,es or no)

A Bolting NA NA NA Rod-SA193 Hex Nuts-SA194 for NV NA Replacement No Pump "2A" Suction Flange Conn.

B C,

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2)

• information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Repair Flange Leak.-

8. Test Conducted: Hydrostatic EL Pneumatic "] Nominal Operating Pressure l' OtherF-Exempt ED Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Aythorization No. N/A Signed 7 A! TECHSPEC Date -20 C

/ Owner or Owner's Designee, Titi e CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of Al C- and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 3 ") --O, to '7 -/T-CI, and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions /JX97 0

'In.pector's Signature Date_7-cA _0 G _

Rex ision 6

( ( (-

ASME Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI I1.,,, DUKE POWER COMPANY la Date 5/10/06 Sheet I of 1

.\Uii,., 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006 2,, CATAWBA NUCLEAR STATION 2a Unit -' I Z22 3 F- Shared (specify UnitsE] )

h 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98688708-15 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CN2144100 Expiration Date N/A 4 Identification of System SM MAIN STEAM SYSTEM Class ,/ACA.. ]/,/ot

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000 (v Idcntilhication of Comnonents Repaired or Renlacement Comtnonents

.. . . .. . . .. . . .. . -... ..- " . .. . . . . . .. I-. . .. . .... ..L.. ___ __ __ ___,

Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Manufacturer Serial Number Built Replaced. or Code Component Replacement Stamped Number Number _(yes or no)

A U Bolt Anvil NA NA For S/R 2-R-SM-1880 & 2-R-SM-1881 NA New No International I B Hex Nuts NA NA NA For S/R 2-R-SM-1880 & 2-R-SM-1881 NA New No D

E F

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Install S/R 2-R-SM-1880 & 2-R-SM-1881_

8. Test Conducted: Hydrostatic s Pneumatic s- Nominal Operating Pressure [- Other [-" Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed A &-, ZfQ TECHSPEC Date :h20 Owner or Owner's Designee. Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holdi ig a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of ,JQ_ and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period .1 -Ž.. 016 to 5- 1.-0 G and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore. neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspe ,on.

n

". AA) Commissions _______

11speclor's Signature Date _!' I Q .20_f Re%ision 6

( C (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. (),,,C. DUKE POWER COMPANY la Date 5/9/06 Sheet I of I

• ,526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. CATAWBA NUCLEAR STATION 2a Unit r 1 Z2 r 3 D" Shared (specify Unitsr-- )

.xu~i, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98688709-15 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CN2144100 Expiration Date N/A 4 Identification of System SM MAIN STEAM SYSTEM Class VAFac. s'w/n,/b

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (h) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Reolacement Comtonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Narne of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASVIE Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number (yes or no)

A Sway Strut Anvil 2001-59 NA S/R 2-R-SM-1885 2001 New Yes International B Rear Bracket, Anvil NA NA S/R 2-R-SM-1885 NA New No Plate, U-Bolt International C Welds Duke Power C-2SM 162 Welds #2-R-SM-1885-1 2-R-SM-1885- 2006 New Yes Co. 2 2-R-SM-1885-3 E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Install S/R 2-R-SM- 1885_

8. Test Conducted: Hydrostatic - Pneumatic I' Nominal Operating Pressure FI Other[] Exempt E Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A TECH SPEC Date SAV _2004 0/1f&

Sioned 7 Owner or Owner's Designee. Title CERTIFICATE OF INSERVICE INSPECTION 1, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A C and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period I "6 "

• to S "IO U and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspeco~av

____ ____ _ __Commissions AC'*)

• Inspector's Signature Date, 5 -"I L) 20_Q(6-__

Re\ ision 6

C C- C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI I (,.A,., DUKE POWER COMPANY la Date 4/18/06 Sheet of

,, 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. '*i, CATAWBA NUCLEAR STATION 2a Unit I [2 2 3 "-1 Shared (specify Units"l )

..,ij,. 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98698974-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System SM MAIN STEAM SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Com onents Repaired or Retlacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped

_Number (yes or no)

A Bolting NA NA NA Studs- SA193, Nuts- SA194 for valve NA Replacement No 2SM-3 B-C D

E--

Revision 6

,* I ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish Valve 2SM-3_

8. Test Conducted: Hydrostatic E]" Pneumatic L1 Nominal Operating Pressure L-- OtherE"Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases ___NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed S2/, , TECH SPEC Date ,20 04 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A/L and employed by HSB I AND lýompany of Connecticut have inspected the components described in this Owners Report during the period !-'T 0 (c to f-16 '6 6 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspectio/

L. ' Commissions A/CJ-" £ Ins ctor's Signature I Date 1 20OOG Rce ision 6

C ( (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owner DUKE POWER COMPANY la Date 3/29/06 Sheet I of I Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ,llant CATAWBA NUCLEAR STATION 2a Unit ["2

[2 3 El Shared (specify Units' )

Al'CSý 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98706897-03 Address 526 S. Church St. Charlotte- N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NS CONTAINMENT SPRAY SYSTEM Class B

5. (a) Applicable Construction Code 11I 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column

_ 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number__ _(yes or no)

A Disc Kerotest NA NA For Valve 2NS-75 NA Replaced No B Disc Kerotest 24513-11 NA For Valve 2NS-75 NA Replacement No C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish Valve 2NS-75_

8. Test Conducted: Hydrostatic El- Pneumatic E] Nominal Operating Pressure r-] Other L- Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE _

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed )" Z 'C TECH SPEC Date 3,&,D 0 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of At P. and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period -3 2 -*&. to 4-IS - G, and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspe on.

V4;UJ Commissions ,ArC_-,

Inspector's Signature Date_* 1$__,200 (0-Revision 6

( C (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. (ownr DUKE POWER COMPANY 1a Date 4/12/06 Sheet I of 1 Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. PIlan CATAWBA NUCLEAR STATION 2a Unit 1 1- [2 E2 3 El Shared (specify Units[] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98707253-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B NV CNEMICAL VOLUME CONTROL SYSTEM

5. (a) Applicable Construction Code 1II 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Com onents Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced.

Replacementor Code Stamped Number _(yes or no)

A Plug/Stcim Fisher NA NA For valve 2NV-309 NA Replaced No Assembly I B Plug/Stem Fisher AF6994-1 NA For valve 2NV309 NA Replacement No Assembly C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish Valve 2NV-309_

8. Test Conducted: Hydrostatic E] Pneumatic E] Nominal Operating Pressure E1] Other-] Exempt E Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicitble Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed A&.rc TECH SPEC Date ,20 6 C

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A! G" and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period -T.,S -OL to 4*1.Z'4G and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described'in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

___ ___ __ Commissions_ ____________

Inspector's Signature Date _A--I - 20_0 Revision 6 s.-

C C ASME Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. O,,*, DUKE POWER COMPANY la Date 5/03/06 Sheet 1 of 1 Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i,,aw CATAWBA NUCLEAR STATION 2a Unit I 22 3 [] Shared (specify Units[] )

.,, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98707254-01 AddrCss 526 S. Church St. Charlotte. N.C. 28201-1006 Typc Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B NV CNEMICAL VOLUME CONTROL SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Renaired or Replacement Compn ents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Narne of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number_ (yes or no)

A Plug Assembly Fisher 6308628-629 NA For valve tag 2NV-294 NA Replaced No B Plug Assenbly Fisher 256255-IA NA For valve tag 2NV-294 NA Replacement No C

D F--

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2)

,, information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Rebuild Valve 2NV-294_

8. Test Conducted: Hydrostatic [l' Pneumatic 1i" Nominal Operating Pressure 1L" Other I- Exempt ED Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicitble Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Si~yned A" IC TECH SPEC Date ,.20 04

- Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of Al L and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period - 07 to -1&-) ( and state that-to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code, Section Xl.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising fromn or connected with this inspection.

2k-x~L~ Commissions AC In's~rs Sinature Date_-" .200G Revision 6

( (? (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. owner DUKE POWER COMPANY la Date 1/22/06 Sheet of Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Plant CATAWBA NUCLEAR STATION 2a Unit 1 [E2 2 3 E] Shared (specify Units[] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98709786-06 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD500175 Expiration Date N/A 4 Identification of System Class NF NW CONTAINMENT PENETRATION VALVE INJECTION WATER

5. (a) Applicable Construction Code m11 1974 Edition, S'75 Addenda, Code Cases_

(b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped

__(yes or no)

A Welds Duke Power C-2RN 160 Welds # 1-R-RN-851-1 thru 4 2006 New Yes Co.

B S/R I-R-RN-851 Anvil NA NA Clevis Hanger, Threaded Rod, Welding NA New No International Lug, Hex Nuts, Plate, Tubesteel, U-Bolt C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2)

. information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace S/R I-R-RN-851 _

8. Test Conducted: Hydrostatic E] Pneumatic "]Nominal Operating Pressure E] Other [E] Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases __NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of uthorization No. N/A Signed Z & zr& TECHSPEC Date 117- .20._

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of rNLMi.RtN, s4MItaAnd employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period /C

• to V/ and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

/ýt a Commissions --- /0 'f-)

Iector's Signature Date _ -IL ,20IL V.L Revision 6

C ( C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI 1.Owner DUKE POWER COMPANY 1a Date 2/6/06 Sheet of Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Pnan, CATAWBA NUCLEAR STATION 2a Unit -' 1 [2 "- 3 [E Shared (specify UnitsE] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98709787-15 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD500175 Expiration Date N/A 4 Identification of System Class NF RN NUCLEAR SERVICE WATER SYSTEM

5. (a) Applicable Construction Code IIm 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column

_ 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Welds Duke Power C-2RN 160 Welds #1-R-RN-850-1 thru 4 2006 Replacement Yes Co. I B Lug Anvil NA NA For S/R I-R-RN-850 NA Replacement No International C Plate & Flat Bar NA NA NA For S/R 1-R-RN-850 NA New No D-E F

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Rework S/R I-R-RN-850_

8. Test Conducted: Hydrostatic El Pneumatic 1"1 Nominal Operating Pressure E' Other E] Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases ___NONE_

(Appli6able Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of uthorization No. N/A Signed, TECH SPEC Date _200 j/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION ILthe undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of TeL -" and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period ',/!,"O" to .. f//// &a and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

~ 4~zc. i`1 Commissions V - lOav Inspect s Signature Date _ 7- IL ,200 G -

Revision 6

( (- (-

.S Nt-B Section XI Malnual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. oner DUKE POWER COMPANY la Date 6/12/06 Sheet I of 1 Addrss 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Piant CATAWBA NUCLEAR STATION 2a Unit El i Z2 El 3 E"] Shared (specify UnitsL- )

Addre, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98711211-06 Address 526 S. Church St. Charlotte, N.C. 28201-1006 1\pc ('ode Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System SM MAIN STEAM SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comnnnents Renaired or Renlaee~ment flnmnornentr Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME

('omponent Manufacturer Serial Number Built Replaced. or Code Number Number(yes Replacement Stamped or no)

.A Steam Generator Westinghouse 1570-03 5 Steam Generator "2D" Secondary NA Replacement No Manway Cover Manway Cover B Bolting NA NA NA Rod- SA193 Hex Nuts-SA194 for SG NA Replacement No "2D" Manway Cover C

D E

Revision 6

ASME Section X1 Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace SG "2D" Manway Cover-

8. Test Conducted: Hydrostatic L- Pneumatic "-- Nominal Operating Pressure Other - Exempt El Pressure 1076 psig Test Temp. 555.5 deg.F.

9. Remarks _ Code Cases _NONEPressure test completed on work order 98790985-01.

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of uthorization No. N/A Signed /_,,(M TECH SPEC Date d/, _20 Q e.

Owner or Owner's Designee, Titlee

/

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of _ ___ and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period  ? to -- O- and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code.Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied. concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_________ Commissions -A/C US7 In 'ctor's Signature Date_ " ,_2 ___

Revision 6

( ( (

.\5Mi"F Sccti n XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. owne, DUKE POWER COMPANY la Date 6/12/06 Sheet I of I Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ,na,, CATAWBA NUCLEAR STATION 2a Unit El I Z2 r- 3 [:] Shared (specify UnitsF' )

Addiceý 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98711213-06 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Ident Iication of System SM MAIN STEAM SYSTEM Class B

5. (a) Applicahle Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Steam Generator Westinghouse 1570-01 4 Steam Generator "2A" Secondary NA Replacement No Mani av Cover Manway Cover B Steam Generator Westinghouse 1570-2 4 Steam Generator "2A" Secondary NA Replacement No Manway Cover Manway Cover D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace SG "2A" Manway Cover-

8. Test Conducted: Hydrostatic E- Pneumatic I' Nominal Operating Pressure Other L] Exempt El Pressure 1076 psig Test Temp. 556.7 deg.F.

9. Remarks _ Code Cases _NONEPressure test completed on work order 98790986-01.

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Saion e d TECH SPEC Date .20

-_i2Z04 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of / L and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period .' to u2/--MO-0 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions f/(~

Inspectoxs Signature Date _? - i .20- 0 1 ___

Revision 6

( ( (

ASME Section X! Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. (),ner DUKE POWER COMPANY Ia Date 4/10/06 Sheet I of I

.ddii,* 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. iini CATAWBA NUCLEAR STATION 2a Unit -" 1 2 E-" 3 E] Shared (specify Unitsl] )

-Add,, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98717037-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B ND RESIDUAL HEAT REMOVAL SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comoonents Repaired or Replacement Components Colurnn I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Disc Kerotest NA NA For Valve 2ND24A NA Replaced No B Disc Kerotest S/N 2 NA For Valve 2ND24A NA Replacement No C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish Valve 2ND24A_

8. Test Conducted: Hydrostatic El Pneumatic -1l Nominal Operating Pressure E] Other "] Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed ,/za TECH SPEC Date 510 _2064 z Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of Al 0- and employed by HSB I AND I Comrnany of Connecticut have inspected the components described in this Owners Report during the period 3 to -+-/ 5-0 G and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

___ a v V'"N Commissions o,*/C,-

Inspector's Signature Date._A1 __ .20_ OG __

Revision 6

C C (-

ASME Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI 1 (h,,I DUKE POWER COMPANY la Date 5/11/06 Sheet I of ?-,- -

Adac 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ,*la,,CATAWBA NUCLEAR STATION 2a Unit I [2 2 3 [ Shared (specify Units[] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98717523-15 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # 21448/00 Expiration Date N/A 4 ldcntification of System NS CONTAINMENT SPRAY SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (h) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Co oonents Repaired or Ret:lacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number

_ (yes or no)

A Pipe/Fittings NA NA NA 8" Flange- SA182 NA New No B Pipe Welds Duke Power C-2NS 150 2492-NS.00-45-1 2492-NS.00-46-18, 2005 New Yes Co. 23 2492-NS.00-44-1 C Bolting NA NA NA Rod- SA564 Hex Nuts- SA564 NA New No D

E F

Revision 6

( ( C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI I. Owner DUKE POWER COMPANY la Date 5/11/06 Sheet 2 of 2 Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ',a,, CATAWBA NUCLEAR STATION 2a Unit 1 Z2 "2 3 - Shared (specify Units[] )

\,di, 4800 CONCORD RD. YORK, S.C. 29745 3 Work Performed By Duke Power Company 3a Work Order # 98717523-15 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # 21448/00 Expiration Date N/A 4 Identification of System NS CONTAINMENT SPRAY SYSTEM Class NF

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comnonents Renaired or Renlacement Comnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column

_ 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number

_ (yes or no)

A Bracket Anvil NA NA For S/R 2-R-ND-144-3 NA Replacement No International B Weld Duke Power C-2NS 150 2-R-NS-144-3 2005 Replacement Yes Co.

C D

E LF Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Install "A" Train Test Loop.

8. Test Conducted: Hydrostatic E- Pneumatic 11 Nominal Operating Pressure E Other F] Exempt El Pressure 47 psig Test Temp. 85 deg.F.

9. Remarks _ Code Cases _NONEPressure Test completed on work orders 98717523-18 and 98739980-18.

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed 2 i& TECH SPEC Date VZ/t _20A..6__

I Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period b - E5-0. to "7 0 1 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions . 7 Ins inature Date- -13 .200 __

Revision 6

( ( (

.\ASME Section Xl Manual Section E Exhibit A FORNI NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. *),,ur DUKE POWER COMPANY I a Date 4/6/06 Sheet / of /

Addess 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i',,at CATAWBA NUCLEAR STATION 2aUnit I [2 2 3 E] Shared (specify Units- )

.-t i]d,,,s 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98718428-15 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200108 Expiration Date N/A 4 Idcntification of System Class NF RN NUCLEAR SERVICE WATER SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comronents Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped

_Number (yes or no)

.-\ Clevis Pipe Anvil NA NA S/R 2-R-RN-288 NA Replacement No I-lanacr International B Treaded Rod and NA NA NA S/R 2-R-RN-288 NA Replacement No Hex Nuts C Welds Duke Power C-2RN 160 Welds # 2-R-RN-288-1, 2,3, 4 2006 New Yes Co.

D E

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (t) size is 81/2in. x tI in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Rework S/R 2-R-RN-288_

8. Test Conducted: Hydrostatic [] Pneumatic [- Nominal Operating Pressure E] Other - Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases __NONE.

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed 4A-; a<

Owner or Owner's Designee. Title TECH SPEC Date e

/ ,20 04 CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of &/C, and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period ,*"j1-&, to . P--O ,and state that to the best of mv knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code, Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_____ ___ __ ___ Commissions A/C- U- 8 Inspector's Signatute Date 4- k5 .200 G -

Revision 6

( ( C lm ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. owner DUKE POWER COMPANY Ia Date 5/4/06 Sheet I of I AIdh,.,, 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. CATAWBA NUCLEAR STATION 2a Unit - 1 [2 ' 3 ' Shared (specify Units' )

,,,,.. 480() CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98726106-15 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CE200326 Expiration Date N/A 4 Identification of System CF MAIN FEEDWATER SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comoonents Renaired or Reolacement Comnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 1 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number Replacement Stamped

_yes or no)

A Pipe Welds Duke Power C-2CF 158 2CA53-29 2CA53-33 2006 Replacement Yes Co.

B C

E F

Revision 6

4 t ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Install 2" CF Pipe-

8. Test Conducted: Hydrostatic El' Pneumatic 1l Nominal Operating Pressure Other "] Exempt []

Pressure 977 psig Test Temp. 108 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed "ZA g& TECH SPEC Date 67,P ,120-0

/ Owner or Owner's Designee. Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of -.A/ - and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period - -0 (o to S "* -0 6 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected %kiththis inspection.

___,__._ Commissions ___'_'_

Insp tor's Signature Date _S -. 20_0 CG_

Revision 6

( ( (-

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. (),,,L1 DUKE POWER COMPANY la Date 4/3/06 Sheet 1 of I Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. iplait CATAWBA NUCLEAR STATION 2a Unit EI" 1 2 ' 3 E- Shared (specify Units] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98728898-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NI SAFETY INJECTION SYSTEM Class A

5. (a) Applicable Construction Code I1 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Retaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number_ (yes or no)

A Valve Kerotest CAB9-3 28914 Seal Weld Bonnet to Body for valve tag 1980 Repaired Yes 2NI-351 B

C D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Repair Valve 2NI-351_

8. Test Conducted: Hydrostatic Eli Pneumatic IEl Nominal Operating Pressure EI Other -' Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases ___NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp NIA Expiration Date N/A Certificate of Authorization No. N/A Signed "~A YSnl: TECHSPEC Date * ,200/.

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of JA C- and employed by HSB I AND I company of Connecticut have inspected the components described in this Owners Report during the period 3.-° 0 -. b to a nd state that to the best of my knowledge and O'-A'-06 belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

! ,*k_*" "N"N 'N\N A) Commissions _ ' c y' *;

Inspector'sSignature Dale Jvl0_ C'2 Revision 6

C (

ASME Section X1 Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owner DUKE POWER COMPANY Ia Date 4/3/06 Sheet 1 of I Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Plant CATAWBA NUCLEAR STATION 2a Unit El 1 02 -1 3 El Shared (specify UnitsEl )

.ddiws' 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98728899-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NI SAFETY INJECTION SYSTEM Class A

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Corn onents Renaired or Renlacement Comnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Valve Kerotest CAB9-4 28915 Seal Weld Bonnet to Body for valve tag 1980 Repaired Yes 2NI-015 B

C D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Repair Valve 2NI-015_

8. Test Conducted: Hydrostatic E"] Pneumatic I"' Nominal Operating Pressure L" Other LI Exempt Z Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed 1! 0Z -g TECH SPEC Date ,20U.

_/__

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of and employed by H B I AND I ompany of Connecticut have inspected the components described in this Owners Report during the period : --d b to 06 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions &I_U)-_)_P_

Inspctor's Siggature Date .Akl\ -,20U (4 Revision 6

C C-

.\SMI Se.'tin Xl Manual Section E xhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. own,- DUKE POWER COMPANY la Date 5/31/06 Sheet 1 of Addies, 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Plant CATAWBA NUCLEAR STATION 2a Unit D"I Z2 " [ ] Shared (specify Units-- )

Addres, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98731479-ZZ Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # cd-200323 Expiration Date N/A 4 Identification of System CA AUXILIARY FEEDWATER SYSTEM Class B

5. (a) Applicable Construction Code II1 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Com nonents Repaired or Renlacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number_ (yes or no)

A VALVE ANCHOR ET697-1-7 1786 2CA57 1994 Replaced Yes DARLING B VALVE ANCHOR AZ2362 1553 2CA57 2005 Replacement Yes DARLING C PIPE WELDS Duke Energy C-2CA 159 2CA61-9 THRU 17, 2CA62-12 2006 Replacement Yes Corporation D PIPE/FITTINGS NA NA NA 4" FLG-SA-105,4" PIPE-SA-106,4" 90 NA Replacement No ELBOW-SA-234, E BOLTING NA NA NA 1 1/4" ROD, SA-193, HEX NUTS SA- NA Replacement No 194

_ __ _ _ _ _ _ _ _ _ _ 9 _ _ _ _ _ _ _ _ _ _

Revision 6

ASME Section Xl Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x I I in. (2)

Sinformation in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work REPLACE/RELOCATE VALVE 2CA-57_

8. Test Conducted: Hydrostatic E] Pneumatic Er Nominal Operating Pressure [n Other L"'] Exempt E]

Pressure 1085 psig Test Temp. 82 deg.F.

9. Remarks _ Code Cases __NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No N/A Signed '*X TECH SPEC Date .20Y_-_

Owner or Owner's/besignee. Title CERTIFICATE OF INSERVICE INSPECTION

1. the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of 1 C and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period to ._2-1-(a and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

-2"s)m Commissions Ai*c 97)

D~ate 2) 14- ,200CC7 Revision 6

C C C ASME Section Xi Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,*, DUKE POWER COMPANY la Date 5/11/06 Sheet I of I Add,', 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. *,at CATAWBA NUCLEAR STATION 2a Unit 1 E2 " 3 E] Shared (specify UnitsE- )

,dLNN, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98731479-33 Address 526 S. Church St. Charlotte, N.C. 28201-1006 T~pc Codc Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200323 Expiration Date N/A 4 Identification of System CA AUXILIARY FEEDWATER SYSTEM Class NF

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Cornonents Renaired or Renlacement Comoonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number

_ (yes or no)

A Lug Anvil NA NA For S/R 2-R-CA-241 NA Replacement No International B Plate NA NA NA For S/R 2-R-CA-241 NA Replacement No C Weld Duke Power C-2CA 159 2-R-CA-241-1 2006 Replacement No Co.

D Sway Strut Grinnell NA NA For 2-R-CA-1631 NA Replacement No lE Weld Duke Power C-2CA 159 2-R-CA-1631-5 2006 Replacement Yes Co.

I:

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Install S/R 2-R-CA-241_

8. Test Conducted: Hydrostatic Eli Pneumatic 1-1 Nominal Operating Pressure El- Other El Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed Al TECH SPEC Date _____/// -,20._

if - Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of d. C and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period - to and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions A&/C 9 7S ________

Inspector".icynture Date7 /-_ 200 ___

Re i~o 1

C (- C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o*, DUKE POWER COMPANY la Date 5/31/06 Sheet 1 of I

,,,5 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006 2.,tCATAWBA NUCLEAR STATION 2a Unit 1 Z2 " 3 E] Shared (specify Units" )

\vu,,, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98731480-15 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200323 Expiration Date N/A 4 Identification of System CA AUXILIARY FEEDWATER SYSTEM Class B

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comn onents Retnaired or Replacement Comoonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped or no)

Number(yes A Pipe/Fittings NA NA NA 4" Fig.- SA105, 4" Pipe- SA106, 4" 90 NA Replacement No Ell- SA234 B Pipe Welds Duke Power C-2CA 159 2CA152-9 thru 18, 2CA151-11 2006 Replacement Yes Co.

C Bolting NA NA NA Rod- SA193, Hex Nuts- SA194 NA Replacement No D Valve Anchor ET69-1-8 1787 Valve tag 2CA61 1994 Replaced Yes Darling E Valvc Anchor AZ361 1552 Valve tag 2CA61 2005 Replacement Yes Darling F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibi( A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 112in. x II in. (2)

S information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Relocate Valve 2CA-61_

8. Test Conducted: Hydrostatic L-- Pneumatic '- Nominal Operating Pressure Other[] Exempt El Pressure 1081 psig Test Temp. 770 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A TECH SPEC Date ,1-/ .2004 Signed Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION

[, the undersigned. holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of N L-

. and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period to )*-<. and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection

- lYv Commissions MCA__

Date -) A Revision 6

( (- (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. ,,,, DUKE POWER COMPANY la Date 5/4/06 Sheet I of 1

\,ldh,., 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. P',, CATAWBA NUCLEAR STATION 2a Unit i1 02 E:1 3 r-1 Shared (specify Units] )

Addrsc 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98731480-31 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200323 Expiration Date N/A 4 Identification of System CA AUXILIARY FEEDWATER SYSTEM Class NF

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Idcntification of' Comn onents Renaired or Reolacement Comnonents CoILImn 1 Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped

_Number (yes or no)

A Snubber Lisega 4617093/017 NA S/R 2-R-CA-1696 NA New Yes B Welds Duke Power C-2CA 159 2-R-CA-1696-1, 2 2006 New Yes Co.

C D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 l/2in. x 11 in. (2)

'../ information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Add S/R 2-R-CA- 1696

8. Test Conducted: Hydrostatic I-- Pneumatic L-I Nominal Operating Pressure [] Other [l Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Aithorization No. N/A Signed TECH SPEC Date 20 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A , and employed-by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 3 -06 to -S - " ,an state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied. concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Q -' i \r*,\AA Commissions _______.___-____

-petor's Sign'*natUre Date _ 20_C (o-Revision 6

( ( (I ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

.............0-

1. Owner DUKE POWER COMPANY la Date 1/22/06 Sheet of Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Plant CATAWBA NUCLEAR STATION 2a Unit El 1 Z2 E1l 3 E"] Shared (specify Units[] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98731786-04 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD500063 Expiration Date N/A 4 Identification of System Class NF NW CONTAINMENT PENETRATION VALVE INJECTION WATER

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number(yes Replacement Stamped or no)

A Welds Duke Power C-2RN 160 Welds # 2-R-RN-359-1, 2-R-RN-360-1 2006 New Yes Co. 2-R-RN-361-1 thru 8 B Rear Bracket Anvil NA NA For S/R 2-R-RN-360 NA New No Assembly International C Spring Cam Anvil 1992300 NA For S/R 2-R-RN-359 1992 New No Internationa D

E F _I _

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2)

\.,/ information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Support Restraints _

8. Test Conducted: Hydrostatic L-] Pneumatic [-] Nominal Operating Pressure '] Other F[] Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_ _

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed & / Jý. TECH SPEC Date / Z ,20!9_

Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of N R.g..AR N A --.

J414618 employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period / 1h 7&6- to ,V111 and state that to the best of my knowledge and belief, the Owner has performed examinations and talen corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

SICommissions . / (~t1)

Ins tor's Signature Date -_2 -_L_0b Revision 6

( C (-

ASMF, Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. >,,.n, DUKE POWER COMPANY la Date 5/03/06 Sheet I of I Addiess 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. itnt CATAWBA NUCLEAR STATION 2a Unit " i [E2 Z2 3 'I Shared (specify Units[] )

Adi,. 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98733767-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Typc Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification ol' System Class B NV CNEMICAL VOLUME CONTROL SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comnonents Renaired or Replacement Comoonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column

_ 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number (yes or no)

.\ Plug Assembly CCI 100611-010- NA For valve tag 2NV-849 NA Replaced No B Plug Assenbly CCI 600479 NA For valve tag 2NV-849 NA Replacement No C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 l/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Rebuild Valve 2NV-849_

8. Test Conducted: Hydrostatic r] Pneumatic r] Nominal Operating Pressure Er Other LF Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Sioxned11Azc v-i*, ....

TECH SPEC Date ,20O_

/ - Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of Cd' and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 3 to " - -)0 G and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

______________ Commissions d oI-IC3t)

I'njpector's §igna ure Date, - ,20_0

"-' (0 Revision 6

( C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. fl,,,L. DUKE POWER COMPANY la Date 3/30/06 Sheet I of I

, 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. pi,.,t CATAWBA NUCLEAR STATION 2a Unit C"] 1 22 3 E1l Shared (specify Units[] )

Add,-es 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98734295-14 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200108 Expiration Date N/A 4 Identification of System Class NF RN NUCLEAR SERVICE WATER SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number(yes Replacement Stamped or no)

A U Bolt and Eye Anvil NA NA For S/R 2-R-RN-365 NA Replacement No Nut International B Hex Nuts and NA NA NA For S/R 2/R/RN/365 NA Replacement No Rod C Welds Duke Power C-2RN 160 Welds # 2-R-RN-365-1, 2, 3 2006 New Yes Co.

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Modify S/R 2-R-RN-365_

8. Test Conducted: Hydrostatic El" Pneumatic [' Nominal Operating Pressure E] Other -- Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(ApplicAble Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed A & TECH SPEC Date VJ6,20 Q f-Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of 7-e"X a_ -,. and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 2,YT(/ 6 to Y/13o/I and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions TAX-)( 0 Inspectr Signature Date _ 4 f1 3.2004 __

Revision 6

C C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,,,. DUKE POWER COMPANY la Date 4/10/06 Sheet of Addis 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. natt CATAWBA NUCLEAR STATION 2a Unit -' I Z2 E" 3 E-' Shared (specify Units[] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order #-9874t-Address 526 S. Church St. Charlotte, N.C. 28201-1006 9.87sy z9?- o7 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class NF NW CONTAINMENT PENETRATION VALVE INJECTION WATER

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Cor onents Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped

_Number (yes or no)

A U-Bolt Anvil NA NA For S/R 2-P-NW-5013 NA Replacement No International B

C D.-

E Pi_

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish S/R 2-P-NW-5013_

8. Test Conducted: Hydrostatic El Pneumatic I-- Nominal Operating Pressure -] Other E] Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of uthorization No. N/A Signed Z &Z,? TECH SPEC Date _.i

,20-04

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of , and employed by HSB I AND I Cornmany of Connecticut have inspected the components described in this Owners Report during the period -t0 to and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspe n.

___ .___, __,_ ___ __ __ __ _ Commissions ,A" _ __ _ __ _ _

+ 12-I, Date* .200) 6 _

Revision 6

C C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,,,r DUKE POWER COMPANY la Date 5/04/06 Sheet I of I Addro. 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. nt',, CATAWBA NUCLEAR STATION 2a Unit E-'I E2 E] 3 D Shared (specify Units"' )

Addres, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98735045-04 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NC REACTOR COOLANT SYSTEM Class A

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Com nonents Renaired or Renlacement Comnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number (yes or no)

A Snubber PSA/3 10048 NA For S/R 2-R-NC-1675 1979 Replaced Yes B Snubbcr PSA/3 199 NA For S/R 2-R-NC-1675 1979 Replacement Yes C

D-E F

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2)

Sinformation in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace S/R 2-R-NC-1675_

8. Test Conducted: Hydrostatic El Pneumatic [- Nominal Operating Pressure i- OtherE 'Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of uthorization No. N/A Sioned AA , TECH SPEC Date -<-/4-/ ,20-6-6

- Owner or Owner's Designee, Titl CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of AIC," and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 3 - .

02-i to A -OG and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected %%iththis inspe 2,.

_ _ _ _ _ _ Commissions iVC_ 7 )

pector's Signature ie - 200 &__

Re' ision 6

( C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASMIE Code Section XI I oi.\,,., DUKE POWER COMPANY 1a Date 5/3/06 Sheet of

\AdIhI. 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. 1'1,,t CATAWBA NUCLEAR STATION 2a Unit -" 1 Z2 E] 3 [E] Shared (specify Units[] )

Addr.,, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98735045-05 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NC REACTOR COOLANT SYSTEM Class A

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (h) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comoonents Reoaired or Renlacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number (yes or no)

A Valve Dresser BS-02868 NA Valve tag 2NC-002 1979 Replaced Yes B Valve Dresser BS-02872 NA Valve tag 2NC002 1979 Replacement Yes C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheet&...

recorded at the top of this form.

7. Description of Work Replace Valve 2NC-002_

8. Test Conducted: Hydrostatics- Pneumatic s" Nominal Operating Pressure Other [] Exempt E]

Pressure 2230 psig Test Temp. 543 deg.F.

9. Remarks _ Code Cases __NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed -Pla xf* TECH SPEC Date .2066 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned. holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of Al

• and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period +-B" '06 to b -J '0 b and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

____________________ Commissions _ _C__") __

inspector s Signature Date,5 -9l " .20 0 __

Revision 0

(. C C ASME Section XI Ma1Inual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,*ne DUKE POWER COMPANY la Date 5/3/06 Sheet of

.dkr,.SN 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. CATAWBA NUCLEAR STATION 2a Unit D-I Z2 0 3 [] Shared (specify Units[] )

\*LILI,, 4800 CONCORD RD. YORK, S.C. 29745

. Work Performed By Duke Power Company 3a Work Order # 98735046-05 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NC REACTOR COOLANT SYSTEM Class A

5. (a) Applicable Construction Code 1II 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number (yes or no)

A Valve Dresser BS-02870 NA Valve tag 2NC-003 1980 Replaced Yes B Valve Dresser BS-02867 NA Valve tag 2NC-003 1979 Replacement Yes C Bolting NA NA NA Rod- SA193, Hex Nuts- SA194 NA Replacement No D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Valve 2NC-003_

8. Test Conducted: Hydrostatic El- Pneumatic 1-] Nominal Operating Pressure Other[] Exempt []

Pressure 2230 psig Test Temp. 543 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed " -44 TECH SPEC Date 42," ,206._Z

// Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of J L- and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period -S G6 to & ") -o G and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_______________m Commissions A/C ")

IspV-tor's Signature Date _Sc)_ .200& __

Revision 6

( ( (-

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. owner DUKE POWER COMPANY la Date 4/11/06 Sheet I of 1 Addr*ess 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i'iant CATAWBA NUCLEAR STATION 2a Unit FI 1 Z22 3 El Shared (specify UnitsD] )

A.-dd,* 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98735058-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System CF MAIN FEEDWATER SYSTEM Class B

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comoonents Renai red or Renlacement Comnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASMIE Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number (yes or no)

A Disc Atwood H533 NA For Valve 2CF166 1997 Replaced No Morrill B Disc Atwood M95 NA For Valve 2CF166 2000 Replacement No Morrill C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 I/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish Valve 2CF-166_

8. Test Conducted: Hydrostatic rL Pneumatic r-] Nominal Operating Pressure El Other r Exempt [0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases -NONE.

(Applicible Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate o Authorization No. N/A Signed 2/

-ge Owner'orOwner's Designee, Title TECH SPEC Date _ ,20_op(2 CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A/ C- and employed HSB I AND I !ýom any of Connecticut have inspected the components described in this Owners Report during the period "1" f -0 ( to It - and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Inspector's Signature Date _ __ .20_

Revision 6

( ( C ASME Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,,,*, DUKE POWER COMPANY la Date 4/11/06 Sheet I of I Akddress 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i,int CATAWBA NUCLEAR STATION 2a Unit 1 1- 2 [ 3 E] Shared (specify UnitsE' )

,\ddr,* 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98735059-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System CF MAIN FEEDWATER SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comoonents Renaired or Reolacement Comnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number _(yes or no)

A Disc Atwood H532 NA For Valve 2CF169 NA Replaced No MorrillI B Disc Atwood C579 NA For Valve 2CF169 NA Replacement No MorrilI I C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish Valve 2CF- 169

8. Test Conducted: Hydrostatic I- Pneumatic LI Nominal Operating Pressure -L Other L'] Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of uthorization No. N/A Signed TECH SPEC Date ,/il ,20 69 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A/,- and employed b HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period . 6 to i{ ol o...and

.. state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

~~r~v Insp ctor's Signature Commissions N Date -4"2-L .20 -0 Revision 6

( (-

.\SME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI I. om,, DUKE POWER COMPANY la Date 4/5/06 Sheet I of I A.Iddi,. 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. 1',,. CATAWBA NUCLEAR STATION 2a Unit 1 Z2 l3 7 Shared (specify Units- )

..\dil.S. 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98735101-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B S\' MAIN STEAM VENT TO ATMOSPHERE

5. (a) Applicable Construction Code Ill 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comnonents Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number Replacement Stamped (yes or no)

A Disc Dresser AAH30 NA Valve tag 2SV-3 NA Replaced No 13 Disc Dresser ADF-12 NA Valve tag 2SV-3 NA Replacement No C-D

'E-Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbished Valve 2SV-3_

8. Test Conducted: Hydrostatic I- Pneumatic [-1 Nominal Operating Pressure El- Other[] Exempt 2 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed " ZC TECH SPEC Date 9115" ,20 Q 4 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of IV C - and employed by HSB I AND I Comnan' of Connecticut have inspected the components described in this Owners Report during the period to *'1.> -6 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore. neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_____Commissions

_ I -

InDSa e S-on0ture Date 4

.l-).20c,'

Revision 6

C C (-

,.\SNII" Secwil XI MN'.llilU. Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. owner DUKE POWER COMPANY la Date 4/5/06 Sheet I of I Addt,.ý 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i,,I,, CATAWBA NUCLEAR STATION 2a Unit 1 1I Z2 I"I 3 D- Shared (specify Units[:] )

Addrc,. 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98735103-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B SV MAIN STEAM VENT TO ATMOSPHERE

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Numbr N(yes D e or no)

B Disc Dresser AAH89 NA Valve tag 2SV-5 NA Replaced No B Disc Dresser ADI-28 NA Valve tag 2SV-5 NA Replacement No C

D E

F Revision 6

• . .° ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbished Valve 2SV-5_

8. Test Conducted: Hydrostatic E- Pneumatic [-1 Nominal Operating Pressure -I Other [:] Exempt Z Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed ,/AS ý~t TECH SPEC Date -/,,-- ,20 -C

/ Owner or Owner's Designee. Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of J C.- and employed by HSB I AND I nompany of Connecticut have inspected the components described in this Owners Report during the period 1- to . - and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code.Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

uolzev-Inspector's Signature Commissions ,/(tý(--

Date4I& ,2_ __

Revision 6

C C- C

.\SNI': Scction Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,,nc, DUKE POWER COMPANY la Date 4/5/06 Sheet I of I A.LdIII 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Iant,, CATAWBA NUCLEAR STATION 2a Unit I Z22 3 -- Shared (specify Units[] )

,.dics, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98735104-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B SV MAIN STEAM VENT TO ATMOSPHERE

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number __ (yes or no)

A Disc Dresser AAH37 NA Valve tag 2SV-20 NA Replaced No B Disc Dresser ADI-26 NA Valve tag 2SV-20 NA Replacement No C

D F

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbished Valve 2SV-20_

8. Test Conducted: Hydrostatic El Pneumatic l" Nominal Operating Pressure Eli Other - Exempt [0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed & !ge TECH SPEC Date .!,,

20. 40,

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION 1, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of / C and employed by HSB I AND I *ompany of Connecticut have inspected the components described in this Owners Report during the period ,3 3&to "IS -04 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

___________________ Commissions _ _ _ _ _ _ _

lnec r's Signature Date 4 - ,200 b Revision 6

( C (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. *1W,, DUKE POWER COMPANY Ia Date 4/6/06 Sheet / of /

AdzC,.' 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. "i,ia CATAWBA NUCLEAR STATION 2a Unit 1-1 Z2 '- 3 E] Shared (specify Units[] )

Addic,, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98735105-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B SV MAIN STEAM VENT TO ATMOSPHERE

5. (a) Applicable Construction Code I1 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number (yes or no)

A Disc Dresser AAH-92 NA For Valve tag 2SV-22 NA Replaced No B Disc Dresser ADF-19 NA For Valve tag 2SV-22 NA Replacement No C

D E-F-

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish Valve 2SV-22_

8. Test Conducted: Hydrostatic r-- Pneumatic r-] Nominal Operating Pressure El Other r-] Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases __-NONE_

(Applicible Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed TECH SPEC Date iZ/1, -20 1 7 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the I

State or Province of // C*. and employedby HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period -1"O 3ff ,

'to G and state that to the best of my knowledge and

-'IS '05" belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

NN ~Commissions ___ ______

Inspector's Signature Date _I-S .20_0 (_:

Rc'.ision 6

C C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,ict. DUKE POWER COMPANY la Date 4/11/06 Sheet I of I

• Adde. 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i,,iam CATAWBA NUCLEAR STATION 2a Unit "l 1 Z2 E" 3 E1 Shared (specify Units[l )

Addres 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98735107-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B SV MAIN STEAM VENT TO ATMOSPHERE

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases_

(b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Com onents Renaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped (ys or no)

A Disc Dresser AAH-88 NA For Valve 2SV-24 NA Replaced No B Disc Dresser ADF-13 NA For Valve 2SV-24 NA Replacement No

D E

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish Valve 2SV-24_

8. Test Conducted: Hydrostatic r-- Pneumatic E] Nominal Operating Pressure EL Other [] Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Appliiiable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of 4uthorization No. N/A SiTned/C * ------

IB v*m-- * .............

TECH P0-C TECH S1PEC( Date Date ý/'// -20jDC

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of /C and employed HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period T *0 6 to 06 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspecpJQ'.

____________Com mi mmssions *A/C () *

[nsp-ctor's Signature Dale - - 200 6 ___

Revision 6

C C C ASME Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owner DUKE POWER COMPANY la Date 3/30/06 Sheet / of /

Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ,',in, CATAWBA NUCLEAR STATION 2a Unit ((I E2 D-13 F Shared (specify Units[] )

,. 4800 CONCORD RD. YORK, S.C. 29745

3. Work Pcrfornmed By Duke Power Company 3a Work Order# 98735717-02 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System CF MAIN FEEDWATER SYSTEM Class NF

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comoonents Repaired or Reolacement Comoonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number_ (yes or no)

A Snubber PSA 9311 NA For S/R 2-R-CF-1002 1979 Replaced Yes B Snubber Lisega 01615123/06 NA For S/R 2-R-CF-1002 2001 Replacement Yes 6

C Snubber PSA 11082 NA For S/R 2-R-CF-1002 1980 Replaced Yes D Snubber Lisega 01615123/06 NA For S/R 2-R-CF-1002 2001 Replacement Yes 2

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Snubbers 2-R-CF-1002_

8. Test Conducted: Hydrostatic Eli Pneumatic LI Nominal Operating Pressure -l Other E] Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed 4 TECH SPEC Date , -20,Q

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of l C and employed by HSB I AND I Comran of Connecticut have inspected the components described in this Owners Report during the period . -2J./06 to ,., 1S 0G and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

__ __ __ __ __ Commissions _______ _

Inspector's Signature Date A . .20- __

Re%i,,ion 6

( C (

ASME Section X1 Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. owner DUKE POWER COMPANY la Date 3/30/06 Sheet 1 of I Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. it:, CATAWBA NUCLEAR STATION 2a Unit 1 1I 2 -' 3 [1 Shared (specify UnitsD" )

.\dihi 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98735717-14 Adcdress 526 S. Church St. Charlotte. N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class NF NV CNEMICAL VOLUME CONTROL SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Snubber PSA 41426 NA For S/R 2-R-NV-1905 2000 Replaced Yes B Snubber Lisega 04617093/00 NA For S/R 2-R-NV-1905 2004 Replacement Yes 8

C--

D I-- - -

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace S/R 2-R-NV- 1905

8. Test Conducted: Hydrostatic E] Pneumatic 1-1 Nominal Operating Pressure -] Other --- Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(ApplicAble Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of uthorization No. N/A Signed / Owner or Owner's Designee, Title TECH SPEC Date V5 0 20 6(

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A& .,-- and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 3 -*1'?-O2, to 1 - (-O= and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_____ _____ Commissions 4& q_____ _ _ __

Inspe-ors Signature Date 4- 0_ __

Revision 6

(- ( (-

ASME Section X1 Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI 1.owner DUKE POWER COMPANY la Date 3/30/06 Sheet of Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Plant CATAWBA NUCLEAR STATION 2a Unit - 1 [2 i-13 [-] Shared (specify Units-' )

A,1,hc, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98735718-10 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System FW REFUELING WATER SYSTEM Class NF

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Comoonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number NuumA1N Replacement Stamped (yes or no)

A Snubber PSA 11568 NA Replace Pivot Pin on S/R 2-R-FW-0003 1981 Repaired Yes B

C D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 1I in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Repair Snubber 2-R-FW-0003_

8. Test Conducted: Hydrostatic 1- Pneumatic -- Nominal Operating Pressure I-' Other [-' Exempt 0g Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE _

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed I aA 6Z,,-  !ý- TECH SPEC Date -5/0 ,20 0,o Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of C-. and employed by HSB I AND I !ompany of Connecticut have inspected the components described in this Owners Report during the period -"Z -06 to +- 1 -0 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

nisg**N* /*Commissions ,Yc-9 "? )

I sp&tor's Signature Date k ,20_0 Revision 6

( C (i.

ASME Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. ()Vo.Ir DUKE POWER COMPANY Ia Date 4/10/06 Sheet I of I Addie., 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. na,, CATAWBA NUCLEAR STATION 2a Unit 1I Z2 - 3 ['1 Shared (specify Units] )

Add,*dcss 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98735718-12 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System KC COMPONENT COOLING SYSTEM Class NF

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comnonents Renaired or Rernlacement Comrnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped

_Number (yes or no)

A Snubber PSA 41793 NA For S/R 2-R-KC-0541 2001 Replaced Yes B Snubher Lisega 03615873/02 NA Fpr S/R 2-R-KC-0541 2003 Replacement Yes 2

C D

E F

Revision 6

I ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace S/R 2-R-KC-0541_

8. Test Conducted: Hydrostatic F] Pneumatic ElI Nominal Operating Pressure EL- Other L-' Exempt Z Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A TECH SPEC Date 2' ,20-6 Sioned

/Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of 1A C. and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the .3 period -S ' to 4- IS-O. and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

________________________ C ommissions _ _________

Inspector's Signature Date_ A- tS 20_0, __

Revision 6

( ( C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. ,,, DUKE POWER COMPANY la Date 4/19/06 Sheet I of 2

., 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. rl,,t CATAWBA NUCLEAR STATION 2a Unit - 1 Z2 ' 3 D" Shared (specify Units" )

Addi'CS 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98737374-02 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200358 Expiration Date N/A 4 Identification of System Class B NW CONTAINMENT PENETRATION VALVE INJECTION WATER

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column 1 Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number (yes or no)

A Pipe/Fittings NA NA NA 2" Pipe- SA376, 2" Pipe- SA312, 2" NA New No Tee- SA182, 2"xl" Insert- SA182 B 2" 45 ell-SA182, 2" 90 ell-SA182, 2" Flange- SA182, 2"x 3/4" Insert- SA182 C Bolting NA NA NA Rod-SA193, Hex Nuts- SA194 NA New No D Pipe Welds Duke Power C-2RN 165 2NW38-11, 12, 2492-NW.00-155-i thru 2006 New Yes Co. 6, 9 thru 17 E 2492-NW.00-156-1 thru 22 F

Revision 6

( (. C

.\SME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. oknc,, DUKE POWER COMPANY la Date 4/19/06 Sheet 2 of 2 Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. rnwiCATAWBA NUCLEAR STATION 2a Unit "1 [' 2 3 [1 Shared (specify Units[:] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98737374-02 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200358 Expiration Date N/A 4 Identification of System Class B NW CONTAINMENT PENETRATION VALVE INJECTION WATER

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number (yes or no)

A Valve Valcor 6 501 Valve 2NW8A 1993 Replaced Yes B Valve Valcor 3 498 Valve 2NW8A 1993 Replacement Yes C

D Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 l/2in. x II in. (2)

',.' information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Install "2A" NW Pipe.

8. Test Conducted: Hydrostatic r- Pneumatic EI] Nominal Operating Pressure Other r-- Exempt E]

Pressure 80 psig Test Temp. 63 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N[A Expiration Date N/A Certificate of uthorization No. N/A T It( - ZV T;1 Date on Owner or Owner's Designee, Title ..... Date..

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of "TNc*-5, and employed by HSB I AND I Company of Connecticut. have inspected the components described in this Owners Report during the period a to 71/1106 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions TY C. ~

Date t' '__ .2(tO(

Revisioni 6

( C C ASME Section X1 Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. (,,,., DUKE POWER COMPANY la Date 4/20/06 Sheet 1 of I Add,'cN. 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. nn,, CATAWBA NUCLEAR STATION 2a Unit E- 1 2 "- 3 ["- Shared (specify Units'- )

Add,.*cs 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98737374-26 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200358 Expiration Date N/A 4 Identification of System Class NF NW CONTAINMENT PENETRATION VALVE INJECTION WATER

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repai red or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column

_ 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or code Replacement Stamped Number _(yes or no)

A U-Bolt Anvil NA NA For S/R 2-R-NW-020, 2-R-NW-021, 2- NA Replacement No International R-NW-022, 2-R-NW-023 B 2-R-NW-025, 2-R-NW-026 C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Reinstall NW Supports-

8. Test Conducted: Hydrostatic EL Pneumatic L"] Nominal Operating Pressure El' Other [] Exempt Z Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificateo uthorization No. N/A Signed TECH SPEC Date ____ __20 6__

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of " and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period - .. I _o

-. to -!//4 fo&. and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore. neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

_____ ____ ____ __Co Commissions -- ' 10,A0 Inspector's Sig ure Date_-l~.OO, _

Re%ision 6

( C (-

ASME Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Ownr DUKE POWER COMPANY la Date 4/19/06 Sheet I of 2 Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. nat CATAWBA NUCLEAR STATION 2a Unit E" 1 Z2 El 3 El Shared (specify UnitsE-' )

Addes. 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98737375-02 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200358 Expiration Date N/A 4 Identification of System Class B NW CONTAINMENT PENETRATION VALVE INJECTION WATER

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME" Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number_ (yes or no)

A Pipe/Fittings NA NA NA 2" Pipe- SA376/312, 2" Tee- SA182, 2" NA New No 90 ell- SA182, 2"xl" Insert- SA182 B 2" Flange- SA182 C Bolting NA NA NA Rod- SA193, Hex Nuts- SA194 NA New No D Pipe Welds Duke Power C-2NW 165 2NW18-20, 21 2492-NW.00-157-1 thru 2006 New Yes Co. 19

[- 2492-NW.00-158-1 thru 5, 7 thru 20 2NW6 IB Body to Bonnet Seal Weld F

Revision 6

( C C"

..\SM I-'Section X I Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. ow.ner DUKE POWER COMPANY la Date 4/19/06 Sheet 2 of 2 Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i:,ia CATAWBA NUCLEAR STATION 2a Unit F-I Z2 "l 3 [1 Shared (specify Units[] )

Addc*. 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98737375-02 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CD200358 Expiration Date N/A 4 Identification of System Class B NW CONTAINMENT PENETRATION VALVE INJECTION WATER

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Valve V(lces or no)

A Valve Valcor 5 500 Valve 2NW61B 1993 Replaced Yes B Valve Valcor 2 497 Valve 2NW61B 1993 Replacement Yes C

D--

E F

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (I) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Install "2B" NW Pipe-

8. Test Conducted: Hydrostatic 11 Pneumatic El Nominal Operating Pressure 1^ Other E- Exempt El Pressure 72.9 psig Test Temp. 60.7 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed TECH SPEC Date ,2066 Owner or Owner's Designee. Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of .  % and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 2.0f.o~or to 7hy/oy, and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

C*. 4it.-*s--- Commissions 7.*, [o ti2 I,

Revision 6

C ( C ASME Section Xl Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. ,,*wner DUKE POWER COMPANY la Date 11/10/05 Sheet of Addres, 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. Piant CATAWBA NUCLEAR STATION 2a Unit I"-1 E2 I' 3 E"- Shared (specify Units[] )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98738962-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B NV CNEMICAL VOLUME CONTROL SYSTEM

5. (a) Applicable Construction Code II 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Co ponents Repaired or Replacement Components Column 1 Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped Number_ (yes or no)

A Bolting Duke Power NA NA Threaded Rod -SA193 Hex Nut-SA194 NA Replacement No Co. for "2B" NV Pump Flange Conn.

B C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is k./ recorded at the top of this form.

7. Description of Work Repair Leak at Flange

8. Test Conducted: Hydrostatic EL Pneumatic E" Nominal Operating Pressure I-" Other [L Exempt Z Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed TECH SPEC Date ////0 -20 .*,

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of NORTH CAROLINA and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 0 - -S-) to,I/ - " - .. and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

1_ý Commissions NC 978 lns~ector's Signature Date _ - f h ,20_C' o S Revision 6

( ( (-

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI I. ow,,,r DUKE POWER COMPANY la Date 5/3/06 Sheet 1 of 1

-ddil,., 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i>i,,, CATAWBA NUCLEAR STATION 2a Unit II"1 [2 2 3 - Shared (specify UnitsE] )

Add.,,, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98742134-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NC REACTOR COOLANT SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Idcntilicaiion of Conmnonents Renaired or Reolacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number NumerReplacement Built Replaced. or Code Stamped Number

_ (yes or no)

A Bolting NA NA NA Rod- SA193 Hex Nuts-SA194 for NA Replacement No 2NVFE5300 Flange Connection B

C D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 l/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Repair Flange Leak.-

8. Test Conducted: Hydrostatic L- Pneumatic L-i Nominal Operating Pressure EI Other[] Exempt N Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Sisned -,,*

TECH SPEC Date -,20

,20 Signed Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A/lCe. and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period &'aO- 06 to 5 O6 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

2 "Am 4ýV-Inspector's Cgnttr Commissions A/*,-- ) b Date _9 -5 ,200~

Revision 6

( C C-

.\SME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. ow,.nr DUKE POWER COMPANY la Date 5/3/06 Sheet of Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. p.at CATAWBA NUCLEAR STATION 2a Unit "I 1 2 "" 3 D-' Shared (specify Units"- )

Aokddss 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98747553-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CE200500 Expiration Date N/A 4 Identification of System KC COMPONENT COOLING SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comnonents Retnaired or Retnlacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Pipe/Fittingls NA NA NA 1 1/2" Pipe-SA312, 2"xl 1/2" Ins.- NA New No

_ SAI05, 2"xl 1/2" Cplg.- SA182_

B Pipe Welds Duke Power C-2KC 166 2KC372-1, 2 2KC371-1, 17, 18, 19 2006 New Yes Co. I C Valve Kerotest TM3-2 11967 Valve tag 2KC412 1976 Replaced Yes D Valve Flowserve 92BEQ 1597 Valve tag 2KC412 2006 Replacement Yes E

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 l/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Valve 2KC412_

8. Test Conducted: Hydrostatic L"' Pneumatic 7I Nominal Operating Pressure 1u Other[] Exempt F]

Pressure 100 psig Test Temp. 93 deg.F.

9. Remarks _ Code Cases __NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed - TECH SPEC Date Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A/ - and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period I 8 i -0 to .-S - ')0 -O and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions AICt9 *ý Inspect r's Signature Date _C" C .21_ (D 6__

Revision 6

( ( (-

ASME Sc*cion XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. owne, DUKE POWER COMPANY la Date 5/11/06 Sheet I of I Addiess 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. p,,an, CATAWBA NUCLEAR STATION 2a Unit f"]I [2 D3 "- Shared (specify Units" )

.\dr,., 4800 CONCORD RD. YORK, S.C. 29745 3 Work Performed By Duke Power Company 3a Work Order# 98747554-01 A\ddrcss 526 S. Church St. Charlotte, N.C. 28201-1006 l1vpc Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CE200500 Expiration Date N/A 4 Identification of System KC COMPONENT COOLING SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Iden~tification of Comnonents Renaiired or Renlacement Comnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 1 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped

_(yes or no)

A Pipc/Fittings NA NA NA 2"xl 1/2" Ins.- SAI05, 1 1/2" Pipe- NA Replacement No SA376 B Pipe Welds Duke Power C-2KC 166 2KC490-1, 2 2KC491-1, 15, 16, 17 2006 Replacement Yes Co.

C Valve Kerotest 24 E684P-I Valve 2KC-393 NA Replaced Yes D Valve Flowserve 93BEQ 1598 Valve 2KC-393 2006 Replacement Yes E

I--S Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 1/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Valve 2KC-393_

8. Test Conducted: Hydrostatic I- Pneumatic E] Nominal Operating Pressure OtherF IExempt [-

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Sisoned v

& /CZ TECH SPEC Date ;/./ ,2040_

Owner or Owner's Designee, Title M

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned. holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of d C and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period I"- 2 0 (o to '7 -I tO(, and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code, Section X1.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions Datec-"- s Sig-nature--

Date7-? 14 .1OO Revision 6

( C C

.\SME Section X1 Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI 1.o,,,*. DUKE POWER COMPANY la Date 5/3/06 Sheet of Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i*,,nt CATAWBA NUCLEAR STATION 2a Unit 1 Z2 D23 [1 Shared (specify Units[] )

Addess 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98747555-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CE200500 Expiration Date N/A 4 Identification of System KC COMPONENT COOLING SYSTEM Class B

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Com onents Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped

_(yes or no)

A Pipe/Fittings NA NA NA 1 1/2" Pipe- SA376, 2"xl 1/2" Red. NA New No

..Cplg-SA182, 2"xl 1/2" Red. Ins. SAI05 B Pipe Welds Duke Power C-2KC 166 2KC432-1, 27, 28, 29 2KC367-1, 2 2006 New Yes Co. I C Valve Kerotest TX5-19 13794 Valve tag 2KC363 1977 Replaced Yes D Valve Flowserve 90BEQ NA Valve tag 2KC363 2006 Replacement Yes E

F Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Valve 2KC363_

8. Test Conducted: Hydrostatic El" Pneumatic E] Nominal Operating Pressure 1 Other [] Exempt El Pressure 100 psig Test Temp. 92 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed 4tC TECH SPEC Date 5.5 ,20 06 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of f % and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period )- c-, -06 to 5 -J -0 (* and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspec i.n

__ _ _ _ _ _ _Commissions A/IC/*--- O*3) ,_

Inspector's Signature Date - _,20_0 C Re\ ision 6

( C (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI 1.o),,er DUKE POWER COMPANY la Date 5/23/06 Sheet 1 of 1

'Wc. 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. , C ATAWBA NUCLEAR STATION 2a Unit EI Z2 " 3 [] Shared (specify Units- )

\,h,,. 4S,)) CONCORD RD. YORK, S.C. 29745

3. \Vork Performed By Duke Power Company 3a Work Order# 98747556-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # CE200500 Expiration Date N/A 4 Identification of System KC COMPONENT COOLING SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000 6 Iltentificmicin nf Cnmnonents Re~naired nr Penlnternent Cnmnnone~nt*

Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Coinlponent Manufacturer Serial Number Built Replaced. or Code Replacement Stamped

_Number _ (yes or no)

A Valve Kerotest CAD9912 13790 Valve tag 2KC344 1977 Replaced Yes B Valve Flowserve 89BEQ 1596 Valve tag 2KC344 2006 Replacement Yes C Pipe/Fittings NA NA NA 2"xl 1/2" Red Ins./Cplg.-SA105, 1/2" NA Replacement No Pipe- SA376 1D Pie,1\VWelds Duke Power C-2KC 166 2KC359-1, 2 2KC361-9, 14, 15, 16 2006 New Yes Co.

F Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Valve 2KC2344_

8. Test Conducted: Hydrostatic [-1 Pneumatic --] Nominal Operating Pressure Other L- Exempt El Pressure 100 psig Test Temp. 92 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed/ &r TECH SPEC Date ,-IZ3 -,206(

IOwner ýor Owner's -DesigneeTitle CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A C.- ./ and employed by HSB I AND I Conl.anv of Connecticut have inspected the components 0

described in this Owners Report during the period / - -7*- to"7 I'f" b and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property darnage or a loss of any kind arising from or connected with this inspection.

Inp&tor's Signature Date - .20_OG Revision 0

( C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owner DUKE POWER COMPANY la Date 3/29/06 Sheet 1 of 1

,d~i,, 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i,,,, CATAWBA NUCLEAR STATION 2a Unit I 22 3 "- Shared (specify Units- )

\t. 4800 CONCORD RD. YORK, S.C. 29745

3. Work Pcrformed By Duke Power Company 3a Work Order# 98759348-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B SV MAIN STEAM VENT TO ATMOSPHERE

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Com onents Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number_

Replacement Stamped (yes or no)

A Disc Dresser ADF06 NA For valve 2SV-12 NA Replaced No B Disc Dresser ADFI0 NA For valve 2SV-12 NA Replacement No C

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 l/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is

\ recorded at the top of this form.

7. Description of Work Refurbish Valve 2SV-12_

8. Test Conducted: Hydrostatic El Pneumatic Ei- Nominal Operating Pressure L] Other --] Exempt 0 Pressure psig Test Temp. deg.F.

9. Remarks _Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed , & _,J Z TECH SPEC Date 3&6 ,20 016"

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A/l Q- - and employed by AND I n of Connecticut have inspected the components described in this Owners Report during the period 2ý4.6 to "I -IS; -4 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

____*____*_____Commissions Al--4: ")

Insector's Signature Date .4-I .20_ 0 __

Revision 6

C C ASME Section X! Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,,er DUKE POWER COMPANY la Date 3/20/06 Sheet I of I Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. i',Ia, CATAWBA NUCLEAR STATION 2a Unit DI 22 3 E[ Shared (specify Units" )

\LICd,., 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98760045-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B NV CNEMICAL VOLUME CONTROL SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number Replacement Stamped

_(yes or no)

A Valve Discs(2) Anchor SS15-4 NA For valve tag 2NV-333 NA Replacement No Darling SS 15-7 B Valve Discs(2) Anchor NA NA For Valve tag 2NV-333 NA Replaced No Darling C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 I/2in. x II in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is

\ recorded at the top of this form.

7. Description of Work Refurbished Valve 2NV-333_

8. Test Conducted: Hydrostatic "l'1 Pneumatic E" Nominal Operating Pressure EIl Other[:] Exempt N Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases __NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A TECH SPEC Date -o 20 04 Si Wned -- Owner or.Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of _____" _ and employed by HSB I AND I Company, of Connecticut have inspected the components described in this Owners Report during the period " ,T-O to Q_,O(. and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspect Commissions AICc'"k A tlor's Signa0ture Date-3-a20-o-n OG Revision 6

,( (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,cr DUKE POWER COMPANY I a Date 4/3/06 Sheet I of I Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ,nat CATAWBA NUCLEAR STATION 2a Unit 1 1] Z2 E2 3 [-l Shared (specify Units'- )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order# 98783351-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class A NV CNEMICAL VOLUME CONTROL SYSTEM

5. (a) Applicable Construction Code 111 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 1 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number_

Replacement Stamped (yes or no)

A Valve Kerotest THAI-10 11828 Bonnet to Body Seal Weld for valve tag 1976 Repaired Yes 2NV861 B

C D

E Revision 6

.4 ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is

"',' recorded at the top of this form.

7. Description of Work Repair Valve 2NV861_

8. Test Conducted: Hydrostatic -- Pneumatic "] Nominal Operating Pressure Eli Other [:] Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A v ",D ....

TECH SPEC Date -,20 0(.

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of i" '. and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period A - ." U-L to -'1! and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this ins jion. \

.,N -. k Commissions ____ ____"____

npector's

• Signature "IC D~ate A-* k ,20-0 Revision 6

(" (- (

ASME Section X1 Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. , DUKE POWER COMPANY la Date 4/10/06 Sheet of

• h526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. n*,t:, CATAWBA NUCLEAR STATION 2a Unit 11 [2 " 3 " Shared (specify Units] )

Addres.s 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98783830-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System CF MAIN FEEDWATER SYSTEM Class NF

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comroonents Reoaired or Reolacement Comoonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped RdEdAvN (yes or no)

A Rod End Anvil NA NA For S/R 2-R-CF-1724 NA Replacement No International B

C D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x 11 in. (2) information in items 1 through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Refurbish S/R 2-R-CF-1724_

8. Test Conducted: Hydrostatic I' Pneumatic L" Nominal Operating Pressure EL Other L- Exempt 10 Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases __NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed Za3 TECH SPEC Date 4,20 04

/ Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of AJC-- and employed b HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period ,-TO G to 12"0 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspecr~n.

ins]e I Vi > eJ3,4J Commissions _ _______

In.jector" sSignature Date -A- 2._ .20_0 G, Re\ iion 6

( C (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. oc, DUKE POWER COMPANY la Date 5/3/06 Sheet I of I Addres 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. iiai CATAWBA NUCLEAR STATION 2a Unit " 1" 1 2 3 l Shared (specify Units- )

Addlvs 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98785424-12 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NI SAFETY INJECTION SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of ComDonents Reoaired or Renlacement Comnonents Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Replacement Stamped

_(yes or no)

A Pipe NA NA NA 2" Pipe- SA376 NA Replacement No B Pipe Welds Duke Power C-2NI 172 2NI255-15, 16, 17, 18 2006 Replacement No Co.

C Valve Kerotest OB5-12 14997 Valve tag 2NI-144A 1977 Replaced Yes D Valve Kerotest AFHI-9 37112 Valve tag 2NI-144A 1985 Replacement Yes E

F Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 l/2in. x 11 in. (2) information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Valve 2NI-144A_

8. Test Conducted: Hydrostatic E-1 Pneumatic [I Nominal Operating Pressure Other I" Exempt El Pressure 1550 psig Test Temp. 85.6 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of thorization No. N/A Signed TECH SPEC Date -5200 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION 1, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of .) - and employed by HSB I AND I Comiany of Connecticut have inspected the components described in this Owners Report during the period 4--3 -06 to 7 0 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

Commissions A10______7 Inspector's Signature Date-? "4 .20_0(o -

Revision 6

( C (

ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. o,,*.n DUKE POWER COMPANY la Date 4/18/06 Sheet / of /

.i,. 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ',, CATAWBA NUCLEAR STATION 2a Unit II [2 2 3 E] Shared (specify Unitsr] )

\Jdic, 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98785454-08 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NI SAFETY INJECTION SYSTEM Class B

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Comnonent* Rennired or Renlneement Comnonent.*

6 - I - - - - - ... ........ ... ..... o.. ... -r.......... C .

Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number(yes Replacement Stamped or no)

A Valve Bonnet Borg Warner NA NA For valve 2NI009A NA Replaced No B Valve Bonnet Borg Warner 30 NA For valve 2NI009A NA Replacement No C

D F

Fz Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 I/2in. x 11 in. (2)

, information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace Valve 2NI-009A Bonnet_

8. Test Conducted: Hydrostatic El- Pneumatic II Nominal Operating Pressure N Other iI1 Exempt E]

Pressure 75 psig Test Temp. 160 deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed AA-~1~ TECH SPEC Date _,2004 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of 'C-. and employed y HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period 4 ,-13-0 to G,-0 and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

2~QLVi~N {\\QP "lIni.pector's Sitgynature Commissions AIL B5)

Date 5-6 .20_0 G C Re%ision 6

C C C ASME Section XI Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. *,,n,. DUKE POWER COMPANY la Date 5/04/06 Sheet I of 1

.ddi,, 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. I',,,t CATAWBA NUCLEAR STATION 2a Unit 1 1" [2 E2 3 E" Shared (specify Units[] )

.Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98785886-01 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B BB STEAM GERATOR BLOWDOWN SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (h) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Number Number _(yes Replacement Stamped or no)

A Snubber PSAI/3 14947 NA For S/R 2-R-BB-1033 1982 Replaced Yes B Snuhher Lisega 03615873/02 NA For S/R 2-R-BB-1033 2003 Replacement Yes 4

C D

E F

Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x I I in. (2)

\ information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

.7. Description of Work Replace S/R 2-R-BB-1033_

8. Test Conducted: Hydrostatic[ - Pneumatic "Nominal Operating Pressure El" Other ["] Exempt N Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed TECH SPEC Date -/t ,120.

0Ownier or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A/ C-. and employed by HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period ,IT- -G to S - qa - and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this ins tion.

sQA iICommissions______________

spector's Signature

)ate 5- -_2OC Re"x iIkil 6

( C C-ASME Section X! Manual Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI 1 , DUKE POWER COMPANY la Date 4/18/06 Sheet / of /

\,dc', 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ,*it CATAWBA NUCLEAR STATION 2a Unit F'11 Z 2 I--3 [:] Shared (specify Units[] )

Addles 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 987862 79-02 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System Class B ND RESIDUAL HEAT REMOVAL SYSTEM

5. (a) Applicable Construction Code III 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

. lIdenitif~iation of C(omnonents Rennired or Renhnremnent (7nrnnnne~nt*

Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number _(yes or no)

A Snubber PSA-I 8718 NA For S/R 2-R-ND-277 1979 Replaced Yes B Snubber PSA-lI-f-U5 NA For S/R 2-R-ND-277 2002 Replacement Yes C

D E

F Revision 6

ASME Section XI Manual Form NIS-2 (Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 81/2in. x II in. (2)

, information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Replace S/R 2-R-ND-277_

8. Test Conducted: Hydrostatic Eli Pneumatic -l Nominal Operating Pressure --l Other [-] Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed A & O(0g**r4e TECH SPEC Date -0

____20 Owner or Owner's Designee, Title CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of A/ e& and employed AND I Company of Connecticut have inspected the components described in this Owners Report during the period 0& to 4 48 -0 G and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

/i2 torsSign e Commission Date 4-~ (8 .2006~ _

Revision 6

(. C (-

ASN.E Section XI ManualI Section E Exhibit A FORM NIS-2 OWNER'S REPORT FOR REPAIRS OR REPLACEMENTS As Required By The Provisions Of The ASME Code Section XI

1. Owne. DUKE POWER COMPANY la Date 5/3/06 Sheet I of I Address 526 S. CHURCH STREET. CHARLOTTE N.C. 28201-1006

2. ant CATAWBA NUCLEAR STATION 2a Unit 1 Z2 -' 3 ["" Shared (specify Units[ )

Address 4800 CONCORD RD. YORK, S.C. 29745

3. Work Performed By Duke Power Company 3a Work Order # 98787227-07 Address 526 S. Church St. Charlotte, N.C. 28201-1006 Type Code Symbol Stamp N/A Authorization No. N/A 3b NSM or MN # NA Expiration Date N/A 4 Identification of System NM NUCLEAR SAMPLING SYSTEM Class NF

5. (a) Applicable Construction Code 1II 1974 Edition, S'75 Addenda, Code Cases (b) Applicable Edition of Section XI Utilized for Repairs or Replacements 1998 Addenda 2000

6. Identification of Components Repaired or Replacement Components Column I Column 2 Column 3 Column Column 5 Column Column 7 Column 4 6 8 Name of Name of Manufacturer N B Other Identification (Size) Year Repaired. ASME Component Manufacturer Serial Number Built Replaced. or Code Replacement Stamped Number (yes or no)

A Pi\ot Pin Anvil NA NA For S/R 2-R-NM-1414 NA Replacement No Intrnational B

C D

E F

Revision 6

ASME Section XI Manual Form NIS-2 ( Back) Section E Exibit A NOTE: Supplemental sheets in form of lists, sketches, or drawings may be used, provided (1) size is 8 I/2in. x II in. (2)

. information in items I through 6 on this reports included on each sheet, and (3) each sheet is numbered and the number of sheets is recorded at the top of this form.

7. Description of Work Restore Support 2-R-NM-1414_

8. Test Conducted: Hydrostatic L-"Pneumatic Ij Nominal Operating Pressure - Other -L Exempt [

Pressure psig Test Temp. deg.F.

9. Remarks _ Code Cases _NONE_

(Applicable Manufacturers Data Records to be attached)

CERTIFICATE OF COMPLIANCE We certify that the statements made in the report are correct and this repair or replacement conforms to the rules of the rules of the ASME Code,Section XI.

Type Code Symbol Stamp N/A Expiration Date N/A Certificate of Authorization No. N/A Signed-A Z w TECH SPEC Date :S_/3

.1

_20cC Owner or Owner's Designee, Title

/

CERTIFICATE OF INSERVICE INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and the State or Province of V/C- and employedpy HSB I AND I Company of Connecticut have inspected the components described in this Owners Report during the period T-2A.-.Q16 to _,_ ______ and state that to the best of my knowledge and belief, the Owner has performed examinations and taken corrective measures described in this Owner's Report in accordance with the requirements of the ASME Code,Section XI.

By signing this certificate neither the Inspector nor his employer makes any warranty. expressed or implied, concerning the examinations and corrective measure described in this Owners Report. Furthermore. neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this ins[ection.

Commissions N)bIGf ___-_

Inspector's Signature DateE 2.20C o -

Rex ision 6

6.0 Pressure Testinq By letter dated October 25, 2005 to the U.S. Nuclear Regulatory Commission, Duke Energy cited their intent to utilize ASME Interpretation, #IN05-09, that allows Duke the 2 nd Energy to start the Catawba Unit 2, 3 rd inspection interval prior to completing inspection interval.

As such, no pressure tests were conducted and credited to the 3 rd inspection interval. The credited as part of the 2 nd Class 1 Leakage test performed during the refueling outage was inspection interval.

Section 6 Prepared By: Date:

Section 6 Reviewed By: Date:

th~ 5(1

_ yao

_ __ý Refueling Outage Report 2EOC14 Page 1 of 1

'I--' Catawba Unit 2 Revision 0 3rd 10-Year Interval May 9, 2006 Section 6