Regulatory Guide 4.15: Difference between revisions

From kanterella
Jump to navigation Jump to search
(Created page by program invented by StriderTol)
(StriderTol Bot change)
Line 1: Line 1:
{{Adams
{{Adams
| number = ML13350A203
| number = ML071790506
| issue date = 12/31/1977
| issue date = 07/01/2007
| title = Quality Assurance for Radiological Monitoring Programs (Normal Operations)-Effluent Streams and the Environment
| title = Quality Assurance for Radiological Monitoring Programs (Inception Through Normal Operations to License Termination) - Effluent Streams and the Environment
| author name =  
| author name =  
| author affiliation = NRC/RES
| author affiliation = NRC/RES
Line 9: Line 9:
| docket =  
| docket =  
| license number =  
| license number =  
| contact person =  
| contact person = Ridgely JN RES 415-6555
| document report number = RG-4.015
| case reference number = DG-4010
| document report number = RG-4.015, Rev 2
| package number = ML071790495
| document type = Regulatory Guide
| document type = Regulatory Guide
| page count = 10
| page count = 28
}}
}}
{{#Wiki_filter:U.S. NUCLEAR REGULATORY COMMISSION                                                                                       December 1977 kREGULATORY GUIDE
{{#Wiki_filter:U.S. NUCLEAR REGULATORY COMMISSION                                                 July 2007 Revision 2 REGULATORY GUIDE
                                    OFFICE OF STANDARDS DEVELOPMENT
                                  OFFICE OF NUCLEAR REGULATORY RESEARCH
                                                                    REGULATORY GUIDE 4.15 QUALITY ASSURANCE FOR RADIOLOGICAL MONITORING PROGRAMS
                                      REGULATORY GUIDE 4.15 (Draft was issued as DG-4010, dated November 2006)
                      (NORMAL OPERATIONS)-EFFLUENT STREAMS AND THE ENVIRONMENT
                                          QUALITY ASSURANCE
                FOR RADIOLOGICAL MONITORING PROGRAMS
                (INCEPTION THROUGH NORMAL OPERATIONS
                                  TO LICENSE TERMINATION)  
                EFFLUENT STREAMS AND THE ENVIRONMENT


==A. INTRODUCTION==
==A. INTRODUCTION==
Section 30.34. ''Terms and Conditions of This guide describes a method acceptable to the                                               Licenses," of 10 CFR Part 30. "Rules of General NRC staff for designing a program to assure the qual-                                              Applicability to Licensing of Byproduct Material."
This regulatory guide describes a method that the U.S. Nuclear Regulatory Commission (NRC)
ity of the results of measurements of radioactive ma-                                              provides that the Commission mayý.incorporate in any terials in the effluents and the environment outside of                                             byproduct material license such'týrnis and conditions nuclear facilities during normal operations.                                                      as it deems appropriate or neccssary. in order to pro- ttr-t hn'ii,: h'*.                                      ",T,
considers acceptable for use in designing and implementing programs to ensure the quality of the results of measurements of radioactive materials in the effluents from, and environment outside of, facilities that process, use, or store radioactive materials during all phases of the facilitys life cycle.
    The NRC regulations that require the control of re-                                              Section 40.41. *.Terms".-nd Conditions of leases of radioactive materials from nuclear facilities,                                            Licenscs,' Licene  of I0.CFR'Part
                                                                                                                                  -            402...Licensing
                                                                                                                                                      "Licesingof        ofSorcSource that require the measurements of radioactive mate-                                                  Material," provides that'tihe Commission may incor- rials in the effluents and environment outside of these                                            porate in any source material license such terms and facilities, or that authorize license conditions not                                              conditionsaasit d8ims appropriate or necessar) to otherwise authorized in the regulations are as                                                    protect heaih',
follows:                                                flSeW1i0 ws:                                        *:.,.':..,, 50o '"-Issuance of Licenses and Con- Section 20.106, "Radioactivity in Effluents to Un-                                          ý,vucttor,1Permits," of 10 CFR Part 50, "Licensing restricted Areas," of 10 CFR Part 20, "Standards for                                                    production  'Iq and Utilization Facilities." provides Protection Against Radiation." provides that a licen-r,                                                t each operating license for a nuclear power plant see shall not release to an unrestricted area radioac- *A' ssued by the Nuclear Regulatory Commission will
                                                                                      "is ,* ~'*;.coitain tire materials .~ý;        in . concentrations
                                ."                      that exceed                          .*:, * .
                                                                                                                such conditions and limitations as the Com- specified in 10 CFR Part 20 or as other%ýRe aui                                            t -Mission deems appropriate and necessary.


thorized in a license issued by the Comnssio*.ýec-,.                                                  Section 70.32, "Conditions of Licenses," of 10
QUALITY ASSURANCE1 (QA) is a fundamental expectation of Title 10, Energy, of the Code of Federal Regulations (10 CFR) for items and activities that are relied on to protect the health and safety of the public and the environment.
tion 20.201, "Surveys." of 10 CFR Pflýt'' fORti                                                  CFR Part 70. "Special Nuclear Material." provides requiresmeaurmetsofleel that a licenseeo conduct    raito        surv.ys, or;' ... including
                                                                            .    .ton            that the Commission may incorporate such terms and measurements of levels of radiation oroncentrations                                              conditions as it deems appropriate or necessary to of radioactive materials, as necessary to i onstrate                                                rotect health.


compliance with the regulations in 10 CFR Part 20.
This guide specifically applies to facilities for which NRC regulations require routine monitoring of radioactive effluents to the environment, and particularly those facilities licensed under the following regulations:
*          10 CFR Part 50, Domestic Licensing of Production and Utilization Facilities (Ref. 1)
*          10 CFR Part 52, Licenses, Certifications, and Approvals for Nuclear Power Plants (Ref. 2)
1 Special terms used in this guide are marked in SMALL CAPITALS the first time they are used, and are defined in the glossary provided in this regulatory guide.


Section IV.B. of Appendix i, "Numerical Guides Paragraph (c) of S4 n.                          /. "',Purpose," of 10                          for Design Objectives and Limiting Conditions for CFR Part 20 states that                         r        nable effort should                    Operation to Meet the Criterion 'As Low As Is Rea- be made by N P-                        se      o maintain radiation ex-                          sonably Achievable' for Radioactive Material in posure, and                 ease*. f rdmoactive materials in                                     Light-Water-Cooled Nuclear Power Reactor effluents t              a ricted reas, as far below the limits                                    Effluents," to 10 CFR Part 50, "Licensing of Pro.
The U.S. Nuclear Regulatory Commission (NRC) issues regulatory guides to describe and make available to the public methods that the NRC staff considers acceptable for use in implementing specific parts of the agencys regulations, techniques that the staff uses in evaluating specific problems or postulated accidents, and data that the staff need in reviewing applications for permits and licenses. Regulatory guides are not substitutes for regulations, and compliance with them is not required. Methods and solutions that differ from those set forth in regulatory guides will be deemed acceptable if they provide a basis for the findings required for the issuance or continuance of a permit or license by the Commission.


specfi*ie P*                          -is reasonably achievable, tak-                            duction and Utilization Facilities," requires that ing into " nt the state of technology and the eco-                                                licensees establish an appropriate surveillance and nomics of"                'ovements in relation to public health                                  monitoring program to provide data on quantities of and safety an to the utilization of atomic energy in                                              radioactive material released in liquid and gaseous the public interest,                                                                              effluents and to provide data on measurable levels of USNRC REGULATORY GUIDES                                                    Comments should be sent to the Secretary at he Comn,$n,,,n.UOS.Nutlea, Regu Regulatory Guides are Issued to desctbe and make available to the public method0                1iotry Commission. Washington. D.C. 20555. Attention Dorheting i,,d Service acceplable to the NRC staff of implementing specific parts of the Commiusion's                Brfanct .
This guide was issued after consideration of comments received from the public.
regulations, to delineate techniques used by the talfl in evaluating specific problems        The guides are issued .n the tollow tnqten broad d-%1.13 or poltulated accidents, or to provide guidance to applicants. Regulatory Guides are not tubssltult for regulations. and compliance with them is not required.                  1.  Power Reactors                          6  Protuclts Met',dt end solutions different from those set out in the guides will be accept.              2.  Research and Test Reactors              7. Tans4tjrlit.tn able if they provide a basis for Ithefindings requisite to the issuance or continuance        3.  Fuels and Materials Faclittes            8. Occuluational Health of e permit or license by the Commli.son.                                                      4.  Enviros',,ental and Siting              9. Antitrust Rerty.v
                                                                                                5.  Materials and Plant Protection          tO. General Comments and suggestions for improvements in thete guides ae encouraged at all times, and guides will be revisad. as apsrotortate. to accommodate comments and                Requests Ifo singlecopies of issued g*i$es (which mavyb. ertsL'Acovll at gotelace to reflect new informatiots or eaperierrce. Howe*er, cOmmlnts on this guide,if                ment on an automatic dctlic'butlon list tO tirngle Coli.es el luture quidtr &it
                                                                                                                                                                            'tieleci-c taceived within about two months alter its jauance, will be partlcularly useful in            div*s*ons should he mnde in writing to the US. Nuclear Regulatory Crmmoissot.


evaluating the need lot an early revision,                                                     Washington. D.C. 20555. Attention. Directo,, Onvruon of DOcument Cunttol
Regulatory guides are issued in 10 broad divisions: 1, Power Reactors; 2, Research and Test Reactors; 3, Fuels and Materials Facilities; 4, Environmental and Siting; 5, Materials and Plant Protection; 6, Products; 7, Transportation; 8, Occupational Health;
9, Antitrust and Financial Review; and 10, General.


radiation and radioactive materials in the environ-            ing, and this need has been widely recognized. Regu- ment. Section lll.B of Appendix I to 10 CFR Part 50            latory Guide 1.21, "Measuring, Evaluating, and Re- provides certain effluent and environmental monitor-          porting Radioactivity in Solid Wastes and Releases of ing requirements. with respect to radioactive iodine if        Radioactive Materials in Liquid and Gaseous estimates of exposure are made on the basis of exist-          Effluents from Light-Water-Cooled Nuclear Power ing conditions and if potential changes in land and            Plants," Regulatory Guide 4.1. "Programs for water usage and food pathways could result in expo-            Monitoring Radioactivity in the Environs of Nuclear sures in excess of the guidelines of Appendix I to 10          Power Plants:" Regulatory Guide 4,8. "Environmen- CFR Part 50.                                                    tal Technical Specifications for Nuclear Power General Design Criterion 60. "'Control of releases          Plants;" and Regulatory Guide 4.14, "Measuring, Evaluating, and Reporting Radioactivity in Releases of radioactive materials to the environment," of Ap- pendix A. "General Design Criteria for Nuclear                  of Radioactive Material in Liquid and Airborne Power Plants." to 10 CFR Part 50 requires that nu-              Effluents from Uranium Mills," all give some guid- clear power plant designs provide means to control              ance on means for assuring the quality of the meas- suitably the release of radioactive materials in gase-          urements of radioactive materials in effluents and the ous a:nd liquid effluents. General Design Criterion            environment outside of nuclear facilities. More com-
Electronic copies of this guide and other recently issued guides are available through the NRCs public Web site under the Regulatory Guides document collection of the NRCs Electronic Reading Room at http://www.nrc.gov/reading-rm/doc-collections/ and through the NRCs Agencywide Documents Access and Management System (ADAMS) at http://www.nrc.gov/reading-rm/adams.html, under Accession No. ML071790506.
64. "Monitoring radioactivity releases." of Appen-              plete and extensive guidance on this subject is pro- vided in this document for nuclear power reactor dix A to 10 CFR Part 50 requires that nuclear power plant designs provide means for monitoring effluent            facilities and for other facilities for which radiologi- discharge paths and the plant environs for radioactiv-         cal monitoring is required by the NRC. This guidance ity that may be released from normal operations, in-            applies both to monitoring that is safety-related and cluding anticipated operational occurrences, and from          monitoring that is not. For safety-related monitoring of nuclear power plants and fuel reprocessing plants, postulated accidents.


other regulatory guides on quality assurance (in the General Design Criterion 1. "'Quality standards              Division I and the Division 3 series of regulatory and records." of Appendix A to 10 CFR Part 50 re-              guides) should be consulted to determine their quires that a quality assurance program be established         applicability, if any. to the radiological monitoring for those structures, systems. and components of a            activities.
*        10 CFR Part 61, Licensing Requirements for Land Disposal of Radioactive Waste (Ref. 3)
*        10 CFR Part 72, Licensing Requirements for the Independent Storage of Spent Nuclear Fuel, High-Level Radioactive Waste, and Reactor-Related Greater Than Class C Waste (Ref. 4)
*        10 CFR Part 76, Certification of Gaseous Diffusion Plants (Ref. 5)
        The guide also may apply to other facilities licensed by the NRC, for which the agency may impose specific license conditions for effluent or environmental monitoring, as deemed necessary to ensure the health and safety of the public and the environment, including those licensed under the following regulations:
*        10 CFR Part 30, Rules of General Applicability to Domestic Licensing of Byproduct Material (Ref. 6)
*        10 CFR Part 40, Domestic Licensing of Source Material (Ref. 7)
*        10 CFR Part 70, Domestic Licensing of Special Nuclear Material (Ref. 8)
         Finally, radiological standards for occupational workers and members of the public are codified in 10 CFR Part 20, Standards for Protection Against Radiation (Ref. 9).
        Although the specific regulations provide the actual requirements, the following presents an overview of applicable NRC regulations addressing limits on radioactive effluents, environmental levels of radioactivity, requirements for effluent and environmental monitoring, and associated QA.


nuclear power plant that are important to safety in  
In accordance with 10 CFR 20.1301, Dose Limits for Individual Members of the Public, the TOTAL EFFECTIVE DOSE EQUIVALENT (TEDE) to individual members of the public from licensed              operation must not exceed 1 milliSIEVERT [1 mSv, or 100 milliREM (mrem)] per year. Uranium fuel cycle          facilities (excluding transportation and disposal) also must comply with the provisions that the U.S. Environmental Protection Agency (EPA) established in 40 CFR Part 190, Environmental Radiation Protection Standards for Nuclear Power Operations (Ref. 10). In addition, 10 CFR 20.1101(d) requires licensees (other than those subject to 10 CFR 50.34a, Design Objectives for Equipment to Control Releases of Radioactive Material in Effluents  Nuclear Power Reactors, discussed below) to restrict releases of airborne radioactive materials so that the highest individual dose to the public will not exceed 0.1 mSv (10 mrem)
per year.
 
In addition, under 10 CFR 20.1101(b), licensees must apply AS LOW AS REASONABLY ACHIEVABLE
(ALARA) concepts to doses to occupational workers and members of the general public. In accordance with 10 CFR 20.1302, Compliance with Dose Limits for Individual Members of the Public, licensees must survey radiation levels to demonstrate compliance with the dose limits, and 10 CFR 20.1101, Radiation Protection Programs, requires licensees to develop, document, and implement radiation protection programs commensurate with the scope and extent of licensed activities and sufficient to ensure compliance with the provisions of 10 CFR Part 20 (Ref. 9).
        In 10 CFR Part 20, Subpart E, Radiological Criteria for License Termination, the NRC provides the radiological criteria for license termination under unrestricted and restricted use scenario
 
====s. The NRC====
considers a site acceptable for unrestricted use if the residual radioactivity that is distinguishable from background radiation does not exceed 25 mrem/year (0.25mSv/year) TEDE to an average member of the critical group, including contributions from groundwater sources. A site can be released under restricted use if the residual radioactivity that is distinguishable from background dose not exceed a yearly dose of
25 mrem (0.25mSv) TEDE with site use restrictions in place.
 
Rev. 2 of RG 4.15, Page 2
 
For nuclear power reactors, 10 CFR 50.34a and 10 CFR 50.36a, Technical Specifications on Effluents from Nuclear Power Reactors, require ALARA concepts for operations to maintain releases of radioactive materials in effluents consistent with the guidelines of Appendix I, Numerical Guides for Design Objectives and Limiting Conditions for Operation to Meet the Criterion As Low As Is Reasonably Achievable for Radioactive Material in Light-Water-Cooled Nuclear Power Reactor Effluents, to
10 CFR Part 50. Licensees must also establish appropriate SURVEILLANCE and monitoring programs to provide QA with respect to (1) areas of equipment operation and (2) data on the quantities or concentrations of radionuclides released in liquid and gaseous effluents. These programs will help to ensure accurate projection of the levels of radiation and radioactive materials found in the environment.
 
Section III.B of Appendix I addresses requirements concerning estimates of radioactive iodine in water and food pathways if land use changes occur after plant construction.
 
The regulations in 10 CFR 30.34, Byproduct Material, 10 CFR 40.41, Source Material,
10 CFR 50.50, Production and Utilization Facilities, and 10 CFR 70.32, Special Nuclear Material, provide that the NRC may incorporate in any governed license such terms and conditions as it deems appropriate or necessary to protect health.
 
For land disposal of radioactive waste, 10 CFR 61.53, Environmental Monitoring, requires measurements and observations to be made and recorded to provide data to evaluate potential health and environmental impacts, including long-term effects, as well as the need for mitigating measures. The monitoring system must be capable of providing early warning of releases of radionuclides from the disposal site. A postclosure monitoring program is also required to detect the release of radionuclides.
 
According to 10 CFR 70.59, Effluent Monitoring Reporting Requirements, licensees authorized to possess and use special nuclear materials for processing and fuel fabrication, scrap recovery, conversion of uranium hexafluoride, or in a uranium enrichment facility shall report to the NRC the quantity of each of the principal radionuclides released to unrestricted areas in liquid and gaseous effluents, and other information as the Commission may require to estimate maximum potential annual radiation doses to the public resulting from effluent releases.
 
Appendix A, General Design Criteria for Nuclear Power Plants, to 10 CFR Part 50 includes several applicable general design criteria (GDC) affecting nuclear power plant designs. GDC 60, Control of Releases of Radioactive Materials to the Environment, requires suitable means to control the release of radioactive materials in gaseous and liquid effluents. GDC 64, Monitoring Radioactivity Releases, requires means for monitoring effluent discharge paths and the plant environs for radioactivity that may be released from normal operations, including anticipated operational occurrences, and from postulated accidents. GDC 1, Quality Standards and Records, requires the establishment of a QA program for those structures, systems, and components that are important to safety to provide adequate assurance that they will satisfactorily perform their safety functions. Appendix B, Quality Assurance Criteria for Nuclear Power Plants and Fuel Reprocessing Plants, to 10 CFR Part 50 establishes the QA requirements for power plants.
 
The requirements in 10 CFR 72.104, Criteria for Radioactive Material in Effluent and Direct Radiation from an ISFSI [Independent Spent Fuel Storage Installation] or MRS [Monitored Retrievable Storage], mandate operational restrictions for maintaining effluents and direct radiation levels in accordance with ALARA concepts, with limits so as not to exceed annual DOSE EQUIVALENTS of .25 mSv
(25 mrem) to the whole body, 0.75 mSv (75 mrem) to the thyroid, and 0.25 mSv (25 mrem) to any other critical organ of any real individual beyond the controlled area.
 
For gaseous diffusion uranium enrichment facilities, 10 CFR 76.87, Technical Safety Requirements, requires licensees to establish technical safety requirements with procedures and equipment Rev. 2 of RG 4.15, Page 3
 
to address (among other things) building and process ventilation and off-gassing, radioactive waste management, and environmental protection. In addition, 10 CFR 76.93, Quality Assurance, requires a QA program satisfying the applicable provisions of the American Society of Mechanical Engineers (ASME) standard QA-1-1994, Quality Assurance Program Requirements for Nuclear Facilities (with Addenda) (Ref. 11).
        Generic Letter 79065 (Ref. 12), regarding the NRCs Radiological Assessment Branch Technical Position on Radiological Environmental Monitoring, provides guidance on the appropriate type of, and location for, sampling and monitoring the environment surrounding nuclear power plants.
 
This regulatory guide presents more complete and extensive guidance on QA for facilities where radiological effluent or environmental monitoring is required by NRC regulations.2 However, this guidance does not address all topics and elements that a facilitys QA program may require (such as requirements of Appendix B to 10 CFR Part 50 for nuclear power plants or 10 CFR 76.93 for gaseous diffusion uranium enrichment facilities).
        The NRC issues regulatory guides to describe to the public methods that the staff considers acceptable for use in implementing specific parts of the agencys regulations, to explain techniques that the staff uses in evaluating specific problems or postulated accidents, and to provide guidance to applicants.
 
Regulatory guides are not substitutes for regulations, and compliance with regulatory guides is not required.
 
2 While not specific to QA, other regulatory guides that address measurements of radioactive materials in effluents and the environment include the following:
        *    Regulatory Guide 1.21, Measuring, Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive Materials in Liquid and Gaseous Effluents from Light-Water-Cooled Nuclear Power Plants (Ref. 13)
        *    Regulatory Guide 4.1, Programs for Monitoring Radioactivity in the Environs of Nuclear Power Plants (Ref. 14)
        *    Regulatory Guide 4.14, Radiological Effluent and Environmental Monitoring at Uranium Mills (Ref. 15)
        *    Regulatory Guide 4.16, Monitoring and Reporting Radioactivity in Releases of Radioactive Materials in Liquid and Gaseous Effluents from Nuclear Fuel Processing and Fabrication Plants and Uranium Hexafluoride Production Plants (Ref. 16)
                                                Rev. 2 of RG 4.15, Page 4


==B. DISCUSSION==
==B. DISCUSSION==
*
As used in the context of this guide, QA comprises all those planned and systematic actions that are necessary to provide adequate confidence in the ASSESSMENT of monitoring result
order to provide adequate assurance that they will satisfactorily perform their safety functions.                    To assure that radiological monitoring meas- Appendix B. "Quality Assurance Criteria for Nu-            urements are reasonably valid, organizations per- clear Power Plants and Fuel Reprocessing Plants," to            forming these measurements have found it necessary
10 CFR Part 50 establishes quality assurance re-              to establish quality assurance programs. These pro- quirements for the design, construction, and opera-            grams are needed for the following reasons: (1) to tion of those structures, systems, and components of            identify deficiencies in the sampling and measure- these facilities that prevent or mitigate the conse-            ment processes to those responsible for these opera- quences of postulated accidents that could cause                tions so that corrective action can be taken, (2) to uridue risk to the health and safety of the pitblic. The        provide a means of relating the results of a particular monitoring program to the National Bureau of Stand- pertinent requirements of this Appendix apply to all safety-related functions of these structures. systems,          ards and thereby to provide a common basis for com- and components. This guide describes a method ac-              paring the results of various programs, and (3) to ob- ceptable to the NRC staff for the design and opera-            tain some measure of confidence in the results of the tion of a program to meet the requirements of Ap-              monitoring programs in order to assure the regulatory pendix B to 10 CFR Part 50, for the safety functions            agencies and the public that the results are valid.


of radiological monitoring of effluents and the                    Existing published guidance on specific quality as- environment.                                                   surance actions which are applicable to radiological As used in the context of this guide. quality assur-        monitoring is limited and, in general, is restricted to ance comprises all those planned and systematic ac-            quality control practices for radioanalytical labora.
====s. QUALITY CONTROL====
(QC) comprises those QA actions that provide a means to measure and control the characteristics of measurement equipment and processes to meet established standards; QA includes QC. This guide makes no further effort to distinguish those elements that may be considered QC from those composing QA.


tions that are necessary to provide adequate confi-            tories (Refs. 1-3). However, quality assurance should dence in the results of a monitoring program, and               be applied to all steps of the monitoring process that quality control comprises those quality assurance ac-          may include sampling, shipment of samples, receipt tions that provide a means to control and measure the          of samples in the laboratory, preparation of samples, characteristics of measurement equipment and proc-              measurement of radioactivity (counting), data reduc- esses to established requirements; therefore, quality          tion, data evaluation, and reporting of the monitoring assurance includes quality cot,,arol.                           results.
Quality assurance is necessary to ensure that all radiological and nonradiological measurements that support the radiological monitoring program are reasonably valid and of a defined quality. These programs are needed (1) to identify deficiencies in the sampling and measurement processes and report them to those responsible for these operations so that licensees may take CORRECTIVE ACTION and (2) to obtain some measure of confidence in the results of the monitoring programs to assure the regulatory agencies and the public that the results are valid. All steps of the monitoring process should involve QA
(e.g., sampling, shipment of SAMPLES, receipt of samples in the laboratory, preparation of samples, radiological measurements, data reduction, data evaluation, and reporting of the measurement and monitoring results) .
          An effective overall management system for quality must precede the design of a QA program. A
document by the International Organization for Standardization (ISO/IEC 17025-2005, Ref. 17) is available for use by laboratories in developing their management system for quality, administrative, and technical operations. Once a quality management system is in place, a DIRECTED PLANNING PROCESS can be used to define the data objectives for the specific monitoring program. The DATA QUALITY OBJECTIVE (DQO)
process (EPA QA/G-4-2006, Ref. 18) provides one example of how to develop and define acceptance and performance criteria for a sample collection, measurement, and data analysis progra


The need for quality assurance is implicit in all re-     *Definitions of special terms used in this guide are given in a quirements for effluent and environmental monitor-            glossary in Appendix A.
====m. The QUALITY====
ASSURANCE PROJECT PLAN (QAPP), which documents how data will be collected, assessed, and analyzed, can form the basis of a QA program (EPA QA/G-5-2002, Ref. 19). The QAPP provides a blueprint of where, when, why, and how a particular project will achieve data of the type and quality needed and expected.


4.15-2
NUREG-1576, Multi-Agency Radiological Laboratory Analytical Protocols Manual (Ref. 20,
hereafter referred to as MARLAP), contains guidance for developing DQOs for risk-informed decisions, and their consequent MEASUREMENT QUALITY OBJECTIVES (MQOs), in the context of radiochemical analyses of environmental samples. The same methodology can be applied in other environmental monitoring contexts. An example of a key MQO is the REQUIRED METHOD UNCERTAINTY at a specified radiation dose or radionuclide concentration. The specific dose may be a fractional amount of a radiation dose limit. The specific concentration may be a fractional amount of an effluent release or environmental radionuclide concentration. For either case, the fractional amount of the limit should be sufficiently small so that a licensee may take reasonable operational actions before the limit is exceede


The scope of this guide is limited to the elements          2. Specification of Qualifications of Personnel of a quality assurance program, which is a planned.
====d. MARLAP====
recommends a PERFORMANCE-BASED APPROACH for selecting methods used to analyze samples or measure dose rates that meet the MQOs. Under this approach, the licensees QA program should incorporate the initial (project METHOD VALIDATION) and continued [internal and external PERFORMANCE EVALUATION (PE)
PROGRAMS] assessment of a methods capability to meet the MQO specifications. Process-radiation monitoring equipment and instrumentation need to have the desired sensitivity to provide both real-time and data-trend values that can correlate to the actual measurements of process streams before release. The radiological environmental measurements program may be used to confirm the adequacy of the process- monitoring equipment.


systematic, and documented program that includes                    The qualification of. individuals performing quality control. Guidance on principles and good                radiological monitoring to perform their assigned practice in the monitoring process itself and guidance          functions should be specified and documented. Speci.
Rev. 2 of RG 4.15, Page 5


on activities that can affect the quality of the monitor-       fication of these qualifications in terms of previous ing results (e.g., design of facilities and equipment)         training and performance on the job or satisfactory are outside the scope of this guide. However, some              completion of proficiency testing is prclerred to spec- references are provided to documents that do provide            ification of education and experience levels.
==C. REGULATORY POSITION==
The QA program of each organization performing radiological effluent or environmental monitoring of nuclear facilities using, processing, or storing radioactive materials during all phases of the facilitys life cycle should be documented by written policies and procedures. Licensees should have sufficient RECORDS of program conduct and performance to demonstrate program adherence. In addition to its own program, a licensee should require any contractor or subcontractor performing support program activities (e.g., sampling, analysis, evaluations, and records) retain records sufficient for the licensee to develop and maintain a QA program covering the applicable program elements.
 
The following presents the QA program elements that should be developed and implemented to ensure the quality of data/results for radiological effluent and environmental monitoring programs.
 
1.      Organizational Structure and Responsibilities of Managerial and Operational Personnel The structure of the organization as it relates to the management and operation of the monitoring programs, including QA policy and functions, should be defined and documented. The authorities, duties, and responsibilities of the positions within this organization, down to the first-line supervisory level, should be described. This should include responsibilities for review and approval of written procedures and the preparation, review, and evaluation of monitoring data and reports.
 
Persons and organizations performing QA functions should have sufficient authority and organizational freedom to identify quality problems; to initiate, recommend, or provide solutions; and to verify implementation of solutions. Reporting should be at a management level that is independent of activity performance, costs, and schedule.
 
Section 2.1.1 of ANSI/ASQC E4-1994 (Ref. 21) and Section 5.2.1 of ANSI N42.23-2003 (Ref. 22)
provide additional guidance on management structure and organizational responsibilities for radiological effluent and environmental monitoring programs.
 
2.      Specification of Qualifications of Personnel The qualifications of individuals needed to carry out assigned radiological monitoring functions should be defined and documented (e.g., as in a job description). Individuals with responsibility for performing quality-related activities should be trained and qualified in the principles and techniques of the activities to be performed. These individuals should maintain proficiency by retraining, reexamining, and recertifying or by periodic performance reviews, as appropriate. Continual training should be conducted as needed to ensure that personnel maintain awareness of events and issues that could affect the quality of program performance.
 
Section 2.3.1 of ANSI/ASQC E4-1994 (Ref. 21) provides additional guidance and criteria for developing personnel training and qualification specifications for radiological effluent and environmental monitoring programs.
 
Rev. 2 of RG 4.15, Page 6
 
3.      Operating Procedures and Instructions Monitoring programs should have written procedures for all activities that generate data, such as dose calculations and measurements, sample collection, sample management and CHAIN OF CUSTODY,
sample preparation and analysis, data reduction and recording, data assessment and reporting, and final sample disposal. Procedures are also needed for addressing support functions, such as operation of process monitors, training, preparation of QUALITY CONTROL SAMPLES, collection of meteorological data, corrective actions, AUDITS, and records. Individuals satisfying the qualifications described in Section C.2 of this regulatory guide should write, review, and revise these procedures.
 
Instructions, procedures, or schedules should be prepared for the functions associated with the QA
program, such as the following:
*        ancillary laboratory functions (including cleaning of glassware, contamination control, and storage of standards and chemicals)
*        CALIBRATION and QC of instrumentation (including range of activity, range of energy, and frequency of calibration)
*        internal QC and external PE programs (including frequency, types, acceptance criteria for the laboratory PERFORMANCE TESTING samples, and individual analyst qualifications)
*        timetable for VERIFICATION and VALIDATION (V&V) of data Chapters 9, 11, and 12 of MARLAP (Ref. 20) provide guidance on the radioanalytical laboratory activities for which procedures are used. MARLAP Chapters 12 - 16 provide technical information that can be used to write or revise procedures. Section 5.4 of ISO/IEC 17025-2005 (Ref. 17) provides additional guidance regarding the content and quality aspects of procedure and method technical content.


some guidance in these areas. The citation of these references does not constitute an endorsement of all An introduction and orientation program, appro- of the guidance in these documents by the NRC staff.
Section 2.5.2 of ANSI/ASQC E4-1994 (Ref. 21) identifies procedures that should be documented and may need control.


Rather, these references are provided as sources of             priate to the size and complexity of the organization.
4.      Records licensees should maintain a system that produces unequivocal, accurate records that document all monitoring activities. Licensees should maintain records of implementation or ongoing activities, such as the following:
*        procedure revision
*        personnel training and qualification records
*        analytical results
*        audits
*        corrective actions
*        intermediate activities or calculations (as may be needed to validate or substantiate final results)
*        records of tracking and control (chain of custody) throughout all processes from sample collection through analysis and reporting of results, including unique identifiers, descriptions, sources, dates/times, packaging/preparation/shipping, and required analyses
*        field logs with sufficient information describing environmental conditions and recording related information and data documenting the nature of the sample and where and how it was taken
*        laboratory notebooks recording related information and data, observations of analysts, and laboratory or other conditions potentially affecting the measurement process
*        electronic data collection and algorithms and QA documentation
*        calculations (including data reduction, analysis, and verification)
                                          Rev. 2 of RG 4.15, Page 7


information to aid the licensee and the licensee's con-         should provide that (a) personnel performing tractors in developing and maintaining a monitoring             quality-related activities are trained and qualified in program.                                                        the principles and techniques of the activities per- formed. and (b) proficiency of personnel who per- form activities affecting quality is maintained by re- Every organization actually performing effluent training, reexamining. and recertifying. as appropriate and environmental monitoring, whether an NRC
*         QC records for radiation monitoring equipment, including the results of RADIOACTIVE SOURCE
licensee or the licensee's contractor, should include          to the activity performed.
          checks, calibrations, INSTRUMEN


the quality assurance program elements presented in this guide.
==T. BACKGROUND==
determinations, and maintenance activities affecting equipment performance
*        notifications to qualified staff that procedural changes affecting data quality have been made
*        QC records for laboratory counting systems and support instrumentation and equipment, including calibrations, maintenance or repair, QC sample results, and traceability of standards used for instrument calibration Records should be legible and identifiable, retained in predetermined locations, and protected against damage, deterioration, or loss. Records should be maintained in a format that is easily retrievable.


3. Operating Procedures and Instructions Written procedures should be prepared. reviewed.
If the media for storage is electronic (as opposed to paper or microfilm/fiche), the licensee should maintain the equipment necessary to read and present the data in an uncorrupted form. The document retention system should allow reconstruction of all activities associated with the generation of analytical results. The licensee should establish a retention time for records consistent with licensing conditions and in accordance with the licensees overall QA program.


==C. REGULATORY POSITION==
Section 2.5 of ANSI/ASQC E4-1994 (Ref. 21) provides guidance on specific types of documents that should be maintained, while Basic Requirement 17 of ASME NQA-1-1994 (Ref. 11) details the administrative criteria that should be considered for inclusion in a program for records and their retention.
and approved for activities involved in carrying out the monitoring program. including sample collection:
 
    The quality assurance program of each organiza-             packaging. shipment. and receipt of samples for offsite analysis: preparation and analysis of samples:
Section 4.13 of ISO/IEC 17025-2005 (Ref. 17) also provides guidance on the control of record
tion performing effluent or environmental monitoring of nuclear facilities for normal operations should be           maintenance, storage. and use of radioactive refer- documented by written policies and procedures and               ence standards; calibration and checks of radiation records. These documents should include the ele-                and radioactivity measurement systems: and reduc- ments given in this section.                                   tion. evaluation, and reporting of data. Individuals who review and approve these procedures should be knowledgeable in the subjects of the procedures.
 
====s. Chapters====
4 and 11 of MARLAP (Ref. 20) discuss documents that should be retained as records. Nuclear Information and Records Management Association (NIRMA) TG11-1998 (Ref. 23), TG15-1998 (Ref. 24), TG16-1998 (Ref. 25), and TG21-1998 (Ref. 26) provide additional information addressing issues in developing and maintaining electronic records programs.
 
5.        Quality Control in Environmental Sampling Sampling of solids, liquids, and gases involves the measurement of sample masses, flow rates, or volumes. The ACCURACY of the instruments or containers used for this purpose should be determined and checked regularly to ensure that sampling performance criteria remain within the limits specified by the MQOs. The results of mass, flow rate, or volume calibrations and associated UNCERTAINTIES should be recorded. The frequency of these calibrations should be specified and should be consistent with the DQOs of the measurement program. The collection efficiencies of the sampling equipment used should be documented; often such documentation is available from the manufacturer. HPS/ANSI N13.1-1999 (Ref. 27) provides guidance on QA and QC for air sampling instruments. Chapter 19 of MARLAP
(Ref. 20) discusses measurement uncertainties in general and volume and mass measurements in particular.
 
Sampling or measurements should be performed using equipment and methods that yield a result that is representative of the population in the particular environmental media. FIELD DUPLICATES are co-located spatially or temporally and should be collected periodically to check REPRODUCIBILITY.
 
Chapter 10 of MARLAP (Ref. 20) discusses the field and sampling issues that affect laboratory measurements, including packaging, shipping, and storage of samples.
 
Some individual environmental samples are collected simply to confirm that radioactivity levels are below a specified (small) fraction of an established concentration limit. In those cases, the MINIMUM
DETECTABLE CONCENTRATION of the method used should be below that specified fraction of the limit.
 
Chapter 20 of MARLAP (Ref. 20) discusses detection limits, while Appendix C to MARLAP covers the relationship between the desired fraction of the limit that is important to detect and the uncertainty of the measurement method. In some cases, a series of measurement results will be averaged for comparison with BACKGROUND LEVELS or a regulatory limit. For such measurements, an appropriate MQO would be the MINIMUM QUANTIFIABLE CONCENTRATION (see Chapter 20 of MARLAP).
                                            Rev. 2 of RG 4.15, Page 8
 
For an isolated, well-mixed population, a single sample or measurement may be sufficient. It is more common, however, for spatial or temporal variations to exist. In that case, the frequency of sampling and number of samples and locations will depend on the level of variability and amount of radioactivity (compared with an established risk-informed limit). NUREG-1575, Multi-Agency Radiation Survey and Site Investigation Manual (Ref. 28, hereafter referred to as MARSSIM), discusses the effect that such variability has on the number of samples that may be appropriate for SURVEYS. In general, the DQO
process may be used together with specific statistical designs (EPA QA/G-9S-2006, Ref. 29) to optimize the sampling. Continuous sampling or integrated measurements may be used to mitigate temporal variability.
 
Part 1, Sections II-11 and II-12, of ASME NQA-1-1994 (Ref. 11) discuss test control and control of measuring and test equipment. Part II, Subpart 2.20, of ASME NQA-1-1994 discusses QA standards for subsurface investigations for nuclear power plants.
 
6.      Quality Control in the Radioanalytical Laboratory The output of the directed planning process includes DQOs that encompass both sampling and analysis activities for a project or program. From the DQOs, a set of MQOs are developed for radioanalytical measurements (see Chapter 3 of MARLAP, Ref. 20). In a performance-based approach, MQOs are critical criteria used for the selection and validation of analytical methods and protocols (see Regulatory Position 8, below) and subsequently form the basis for the ongoing and final evaluation of the analytical data. The type, frequency of, and evaluation criteria for QC samples are developed during the directed planning process and are incorporated into ANALYTICAL PROTOCOL SPECIFICATIONS (APSs) for a project (see Chapter 3 of MARLAP, Ref. 20).
        Chapter 18 of MARLAP provides guidance on monitoring key laboratory PERFORMANCE
INDICATORS    to determine whether a laboratorys measurement processes are in control. The chapter also provides information on likely causes of excursions for selected laboratory performance indicators, such as chemical yield, instrument background, and QC samples. Appendix C to MARLAP provides the rationale and guidance for developing MQOs for select method performance characteristics and gives guidance on developing criteria for QC samples.
 
Performance criteria for radioanalytical measurements should be selected to provide a management tool for tracking and trending performance and to identify precursors to nonconforming conditions.
 
Laboratories should satisfy program-specific criteria for all measurement processes, including necessary levels of PRECISION, acceptable BIAS, and applicable detection levels.
 
6.1      Calibration and Quality Control of Instruments, Measuring Devices, and Test Equipment Instruments, devices, and test equipment used for measuring radioactivity should be operated, calibrated, and maintained to ensure that analytical specifications are met. All equipment should be operated, calibrated, and maintained in adherence to any applicable standards and methods and as specified in the laboratorys quality manual and standard operating procedures. Instrument configurations during calibration should match those used for subsequent analytical measurements of samples.
 
Calibrations of instruments should be made using CERTIFIED REFERENCE MATERIALS of known and documented value and stated uncertainty and should be traceable to a national standards body, such as the National Institute of Standards and Technology (NIST) in the United State
 
====s. CALIBRATION SOURCES====
should be prepared in a manner that provides comparability to TEST SOURCES with respect to source geometry, positioning relative to the detector, source composition, and distribution of the test-source material within a container or on a source mount (see Section 15.2 of MARLAP, Ref. 20).
                                          Rev. 2 of RG 4.15, Page 9
 
The frequency of calibrations should be consistent with the stability and performance of the instrument. Complete system calibration should be performed before initial use or following system maintenance, repair, or any other changes in environment or operating conditions that could affect performance (ASTM D7282-2006, Ref. 30). In addition, Sections 15.2 and 15.3 of MARLAP (Ref. 20)
present general guidance regarding calibrations of instruments. Chapter 15 of MARLAP also presents guidance specific to calibrations of different instrumentation types.
 
The continuing validity of calibrations should be checked periodically as specified in a laboratorys quality manual (see Chapter 18 of MARLAP, Ref. 20). Quality control checks of radioanalytical instrument calibration parameters, such as detector response or energy and resolution calibrations for spectrometers, should be performed by measuring the response of each radiation detection system to appropriate CHECK SOURCES. Instrument QC frequencies are generally performed daily for systems used continually or before use for those systems periodically employed, but frequencies may vary by instrument type. Instrument QC checks should meet predefined acceptance criteria for the respective calibration parameter and should ensure that conditions have not significantly changed since initial calibration (ASTM
D7282-2006, Ref. 30).
        Instrument-calibration QC check results should be tracked, trended, and compared with predetermined ranges of acceptable performance. For example, if a monitors response to a daily check source showed a trend that may lead to a condition outside of established acceptance criteria, a calibration may be needed to reestablish acceptable operation. Section 18.5 of MARLAP (Ref. 20) and ASTM D7282-
2006 (Ref. 30) discuss radioanalytical instrument-calibration QC parameters.
 
Additional method-specific quality controls (e.g., chemical yield, spectral quality, resolution) may apply to certain methods and should be tracked and trended using control or tolerance charts to identify conditions that could be adverse to quality.
 
The laboratory quality manual and standard operating procedures should address the use, calibration, maintenance, and QC of all nonradiological instruments, measuring devices, and test equipment used for measuring or quantifying other necessary data (e.g., sample masses or volumes, temperatures). All measurement and test equipment should be calibrated before use and adjusted to maintain accuracy within established limits. Quality control checks should be performed at specified frequencies and should verify that instruments are operating to specified performance levels.
 
Nonradiological instruments, measurement, and test equipment should be operated according to manufacturers instructions, according to established standards, or as specified in the laboratory quality manual and procedures. Section 18.6.7 of MARLAP (Ref. 20) provides guidance on control, calibration, and maintenance of calibration of apparatus used for mass and volume measurements. ISO/IEC 17025-
2005 (Ref. 17) provides general guidance on establishing quality controls for nonradiological instruments.
 
Items that do not conform to specified criteria should be controlled to prevent inadvertent use. These items should be tracked through the corrective action program.
 
Careful control of contamination and routine monitoring of instrument background are integral parts of a measurement QC program. Determination of the background counting rate should be performed on a regular, predefined frequency for systems in routine use and should ensure that analytical specifications for applicable programs can be met. Instrument backgrounds used to determine a net count rate should replicate actual sample measurement conditions as closely as possible (i.e., using appropriate sample containers and geometries).
                                          Rev. 2 of RG 4.15, Page 10
 
Section 18.5.1 of MARLAP (Ref. 20) provides guidance on measurement and control of instrument backgrounds. Section 18.3 and Attachment 18A of MARLAP contain guidance on the statistical evaluation of performance indicators and on using control and tolerance charts.
 
Sections 10-13 and 20-25 of ASTM D7282-2006 (Ref. 30) and Section A.5.2 of ANSI N42.23-
2003 (Ref. 22) provide additional guidance on instrument response source checks, background checks, and the use of control charts. ASTM MNL 7A-2002 (Ref. 31) provides guidance on setting up and using control charts.
 
6.2      Internal Quality Control Samples and Analysis The use of QC samples should be an integral element of a laboratory QA program. Chapter 18 of MARLAP (Ref. 20) defines the different types of laboratory QC samples and provides guidance on evaluation techniques for QC samples. The laboratory should have as part of the normal operational sample load the following QC samples:3
*        BLANK
*        MATRIX SPIKE
*        LABORATORY CONTROL SAMPLE
*        LABORATORY DUPLICATE
        Analysis of QC samples should be performed as a part of the routine operation of a laboratory to verify that laboratory operations are consistent with applicable specifications. The QC program should specify the type of and minimum frequency for processing QC samples. For example, this frequency may be defined as a minimum percentage of the total number of samples analyzed, a certain number per operational time interval (e.g., once per shift) or per sample batch, or a licensee-specified frequency based on laboratory-specific parameters. As part of its QC program, the laboratory may prepare and analyze BLIND SAMPLES, provided the individuals responsible for preparing the samples are not directly responsible for conducting the laboratory analysis. For example, the laboratorys assigned QC specialist may have the responsibility for preparing and submitting blind samples (blank, duplicate, laboratory control sample, and matrix spike). Blind samples are used primarily as a tool for evaluating the performance of individuals rather than as part of the laboratory QC load.
 
Acceptability of QC sample results should be evaluated based on criteria from the QC program, which include specific equations based on METHOD UNCERTAINTY. Chapters 7 and 18 of MARLAP
(Ref. 20) provide guidance on the evaluation of QC samples.
 
Quality control sample results should be tracked, trended, and compared with predetermined ranges of acceptable performance to identify conditions that are in, or may lead to, nonconformance with program specifications. Such conditions should be tracked through the corrective action program.
 
6.3      Performance Evaluation Program (Interlaboratory Comparison)
        Participation in an external PE program is an important independent check on the accuracy, possible bias, and precision of some radioanalytical or measurement methods used in a radiological monitoring program. Internal and contract radioanalytical laboratories used in the monitoring program should participate in one or more applicable PE programs that are administered by organizations that have an active measurement assurance (traceability) program with NIST (ANSI N42.22-1995, Ref. 32). Chapter
3 Note that this list does not include field duplicate samples that are part of the QC requirement for sampling.
 
Rev. 2 of RG 4.15, Page 11
 
5 of MARLAP (Ref. 20) recommends incorporating the criteria for a radioanalytical laboratory to participate in a PE program into the statement of work for services. Several external PE programs administered by government agencies or commercial radioactive-source suppliers are available for radionuclides and matrices germane to radiological monitoring programs. The PE program should provide fundamental sample types (e.g., solid, liquid, gas) and radionuclides (e.g., alpha-, beta-, and gamma- emitting nuclides) of interest at the facility. When available, laboratories should analyze samples as offered by a PE program on a frequency stipulated by the monitoring programs QA criteria, with all types of samples and analyses repeated at least biennially. Chapter 18 of MARLAP (Ref. 20) provides information on organizations that administer PE programs.
 
Acceptable performance criteria for results of performance-testing samples should be established that are consistent with the MQOs for the radiological monitoring project or program. For certain monitoring activities, the acceptance criteria of the PE program may be satisfactory. The performance in a PE program should be tracked and trended as one of the performance indicators for the laboratory and evaluated as part of the corrective action program.


In addition to its own program, a licensee should require any contractor or subcontractor performing monitoring activities for the licensee to provide a                  Guidance on principles and good practice in many quality assurance program consistent with the provi-            of these activities is presented in NRC regulatory sions of this guide, as follows:                                guides (Refs.4-7) and other publications (Refs. 2.3.
7.        Quality Control for Radioactive Effluent Monitoring Systems
7.1      Radioactive Effluent Process Monitors An initial, primary radiation monitor calibration that meets the specifications of ANSI N42.18-
2004 (Ref. 33), should be performed with radioactive sources traceable to a national standards body (such as NIST). Calibrations should be repeated periodically using (1) STANDARD REFERENCE MATERIALS or (2)
certified reference materials that can be directly traced to the initial, primary calibration. Complete system calibration  including electronics, detector, and any support functions (such as alarm, display, and recording devices)  should be performed at a frequency that ensures system reliability and accuracy or after repair or maintenance that may affect instrument calibration. Unless otherwise specified in license requirements, the licensee should verify and validate the complete effluent monitoring system every 12 months. This frequency may be extended to longer time periods coinciding with facility maintenance schedules, such as refueling for nuclear power plants, if the licensee has verified proper system operation through established system reliability and more frequent source checks and functional checks.


8-25). In addition to these publications, the American Public Health Association is preparing a book on
Detectors should be response-checked periodically4 for continuous effluent release points (e.g., ventilation systems and secondary water systems) and before release for batch discharges (e.g., primary boundary or containment purges and liquid waste tank releases). Licensees should ensure that check sources are of sufficient radiochemical purity so that the activity of the source may be corrected for decay to the date of measurement. These check sources need not be traceable to a national standards body (e.g., NIST). Whenever practicable, check sources should be an integral part of the monitoring system and should be remotely actuated. The functionality of isolation or alarm functions should be verified periodically, preferably by use of a radiation source.
1. Organizational Structure and Responsibilities                quality assurance practices in health laboratories that of Managerial and Operational Personnel                      will include a chapter on radiochemistry. and Scien- tific Committee 18A of the NCRP is preparing a The structure of the organization as it relates to the       manual of radioactivity measurement procedures that management and operation of the monitoring pro.                 will be a revision of NCRP Report 28, NBS Hand- gram(s), including quality assurance policy and func-            book 80, "'A Manual of Radioactivity Procedures."
tions, should be presented. The authorities, duties, and responsibilities of the persons holding specified positions within this organization should be stated, including responsibilities for review and approval of            4. Records written procedures and for preparation, review, and evaluation of monitoring data and reports.                          The records necessary to document the activities performed in the monitoring program should be spec- Persons and organizations performing quality as-            ified in the quality assurance program.


surance functions should have sufficient authority and organizational freedom to identify quality prob-                One key aspect of quality control is maintaining lems; to initiate, recommend, or provide solutions;              the ability to track and control a sample in its prog- and to verify implementation of solutions.                      ress through the sequence of monitoring processes.
Trends of process radiation monitor readings versus total radionuclide concentrations in the monitored release path should be performed routinely. These trends should be based on the results of analyses for specific radionuclides in samples taken from the release path that will yield a monitor response. Deviations in the trend may occur if concentrations or the mixture of radionuclides changed significantly (for example, during a fuel cycle in which significant fuel defects exist). The licensee should define the monitor-response parameter for all radiation monitors. The monitor-response constant should be adjusted to maintain this correlation between effluent radionuclide concentration and monitor response.


4.15-3
4 Frequencies should be appropriate to the instrument under consideration and may be dictated by license conditions.


Records to accomplish this should cover the follow-              Procedures for sampling, packaging, shipping, and
Rev. 2 of RG 4.15, Page 12
*    ing proce.sses: field and inplant sample collection and      storage of samples should be designed to maintair (l;!:
    sample description; sample receipt and laboratory              integrity of the sample from time of collection t, timc identification coding, sample preparation and                  of analysis. Aqueous samples may present a particu-
*  radiochcmical processing (e.g., laboratory note-              lar problem in this regard, and one of the most severe books); radioactivity measurements (counting) of              problems has been encountered with aqueous samples
*  samples, instrument backgrounds. and analytical                of radioactive wastes from operating nuclear reactors blanks. and data reduction and verification.                  (Ref. 2 ).
        Quality control records for laboratory counting sys-          Guidance on the principles and practice of sam- tems should include the results of measurements of            pling in environmental monitoring is provided in sev- radioactive check sources, calibration sources, back-          eral publications (Refs. 2,9.19). In addition, workers grounds. and blanks.                                          at the National Bureau of Standards (NBS) have pub- lished the results of a survey of information on sam- Records relating to overall laboratory performance        pling, sample handling, and long-term storage for should include the results of analysis of quality con-        environmental materials (Ref. 13). Some guidance on trol samples such as analytical blanks, duplicates,            the principles and practice of air sampling is provided interlaboratory cross-check samples and other quality          in References 15, 17, and 22. Guidance on the prin- control analyses; use of standard (radioactive) refer-        ciples and practice of water sampling is provided in ence materials to prepare working standards; prepara-          numerous publications (Refs. II, 12, 23-25).
    tion and standardization of carrier solutions; and            6. Quality Control in the Radioanalytical Labora- calibration of analytical balances.                                tory Additional records that are needed should include              6.1 Radionuclide Reference Standards-Use for the calibration of inline radiation detection equip-                    Calibration of Radiation Measuretnenit ment. air samplers, and thermoluminescence                            Systemns dosimetry systems; verification and documentation of              Reference standards are used to determine counting computer programs; qualifications of personnel; and            efficiencies for specific radionuclides or, in the case results of. audits.                                            of gamma-ray spectrometry systems, to determine counting efficiency as a function of gamma-ray The minimum period of retention of the records            energy. A counting efficiency value is used to con- should be specified. Only the final results of the            vert a sample counting rate to the disintegration rate monitoring programs need be retained for the life of          of a radionuclide or to a radionuclide concentration.


the facility.                                                 (Guidance on calibration and usage of germanium de- tectors for measurement of gamma-ray emission rates of radionuclides is being prepared by a writing group of the Health Physics Society Standards Committee
7.2      Flow Monitoring Instrumentation Continuous sampling of liquids and gases involves the measurement of sample flow rates and/or sample volumes. The accuracy and associated uncertainty of the devices used for this purpose should be determined on a regularly scheduled basis, and adjustments should be made as needed to bring the performance of the devices within specified limits. The results of these calibrations should be recorded.
  5. Quality Control in Sampling (Including Packag-              for publication as an ANSI Standard.)
      Ing, Shipping, and Storage of Samples)
                                                                      Radionuclide standards that have been certified by Continuous sampling of liquids and gases involves         the NBS, or standards that have been standardized the measurement of sample flow rates and/or sample             using a measurement system that is traceable to that volumcs. The accuracy of the devices used for this             of the NBS,* should be used when such standards are purpose should be determined on a regularly sched- uled basis, and adjustments should be made as                 *For a discussion by NBS staff members of the concept of needed to bring the performance of the devices within         traceability of radioactivity measurements to NBS, see Refer- specified limits. The results of these calibrations           ence 27.A brief summary of this discussion is as follows: There should be recorded. The frequency of these calibra-            are both direct and indirect traceability. Direct traceability to NBS exists when. any outside laboratory prepares a batch of tions should be specified and should be based on the          calibrated radioactivity standards and submits several randomly required accuracy, purpose, degree of usage, stability        selected samples to NBS for confirmation or verification. Indi.


characteristics, and other conditions affecting the            rect traceability to NBS exists when NBS provides "unknown"
The frequency of these calibrations should be specified and should be based on the necessary accuracy, purpose, degree of usage, stability characteristics, and other conditions affecting the measurement.
*  measurement. Continuous sampling should be dem-                calibrate radioactivity samples to one or more laboratories which in turn make measurements of activity that agree within certain onstrably representative of the material volumes sam-          specified limits with those of NBS. Thus there can be 1%, etc.,
  pled. The collection efficiencies of the samplers used        traceability. Regular use of NBS radioactivity standards by an should be documented.                                          outside laboratory to calibrate its measuring equipment does not, in the view of the NBS staff, constitute traceability. Only when Grab samples should be demonstrably representa-            the outside laboratory can measure the activity of an unknown sample and send back values to NBS that agree with NBS values tive of the material sampled, and replicate samples            within a certain specified range of error does NBS consider that should be taken periodically to demonstrate the re-            traceability has been established. NBS notes that this condition producibility of sampling.                                    can be achieved without using a single NBS standard.


4.15-4
Any flow-rate measuring devices associated with the system should be calibrated to determine actual flow rates at the conditions of temperature and pressure under which the system will operate. These flow rate devices should be recalibrated annually, but the frequency may be extended to that established for the radiation detector system, provided sufficient operating experience exists and an accelerated measurement check frequency gives sufficient data to ensure reliable performance.


available. Otherwise, standards should be obtained            with automatic sample changers, background mncas- from other reputable suppliers. An "International Di-         urements should be included within each counting rectory of Certified Radioactive Materials" has been          cycle.
Flow measuring devices should be checked periodically on an established frequency, considering the variability of the instrument, and recalibrated when established control limits are exceeded. HPS/ANSI
N13.1-1999 (Ref. 27) provides additional guidance on QA and QC measures for the use, maintenance, and calibration of airborne sampling instrumentation. ANSI N42.18-2004 (Ref. 33) provides additional guidance on the calibration of liquid flow monitors.


publi.;hcd by the International Atomic Energy Agency (Ref. 26).                                                  For alpha- and gamma-ray spectrometry systems, energy-calibration sources (i.e.. a source containing a Acceptable standards for certain natural radionuc-          radionuclide. or mixture of radionuclides. emitting lides may be prepared from commercially available              two or more alpha or gamma rays of known energies)
7.3      Grab Sampling of Effluent Process Streams Whenever practicable, effluent releases should be batch-controlled and released when the volume to be released has been mixed sufficiently to ensure uniform concentration. Sampling and analysis for each batch should be performed, and release conditions set, before release. A certain percentage of all batch releases should have field duplicates taken either before or during the release to assess the reproducibility of sampling and the effectiveness of the mixing process before release. Where possible, samples that are spatially or temporally separated should be collected periodically to verify representativeness.
high-purity chemicals. For example, potassium-40              arc counted to determine the relationship between standards for gross beta measurements or gamma-ray            channel number and alpha- or gamma-ray energy.


spectrometry may be prepared from dried reagent-              The frequency of these energy calibration checks de- grade potassium chloride.                                     pends on the stability of the system but usually is in the range of daily to weekly. The results of these The details of the preparation of working standards          *l.ci,,uienlents should be recorded and compared to from certified standard solutions should be recorded.          predetermined limits in order to determine whether or The working standard should be prepared in the same            noi system gain and zero level need adjustment. Ad- form as the unknown samples, or close approxima-              justmients should be made as necessary.
For continuous-effluent discharges, composite samplers should be employed. However, periodic grab samples may be used when composite sampling of a continuous discharge point is not feasible. When grab samples are collected instead of composite samples, licensees should design the sampling program to sample at the time, location, and frequency that ensures each sample is representative of the radioactive materials released.


tion thereto.
7.4      General Quality Control Considerations The QC plan should address the following items:
*        Sampling should be performed using calibrated instruments and equipment when taking a composite sample.


Additional checks needed for spectrometry systems Efficiency calibrations should he checked periodi-          are the energy resolution of the system and the count cally (typically monthly tc yearly) with standard              rate (or counting efficiency) of a check source. These sources. In addition, these checks should be made              should be determined periodically (usually weekly to whenever the need is indicated, such as when a sig-            nmonthly for energy resolution and daily to weekly for nificant change in the measurement system is de-              count rate) and after system changes, such as power tected by routine measurements with a check source.            failures or repairs, to determine if there has been any significant change in the system. The results of these measurements should be recorded.
*        Collection efficiencies based on the physical configuration of the sampling point and the type of collector should be documented. Vendor-supplied data may be used where adequate documentation exists to ensure the reliability and accuracy of data.


6.2 Performance Checks of Radiation Measure- Inenit Systems                                            6.3 Analysis of Quality' Control Samples Determination of the background counting rate and             The analysis of quality control samples provides a the response of each radiation detection system to ap-        means to determine the precision and accuracy of the propriate check sources should be performed on a              monitoring processes and include!, both intralabora- scheduled basis for systems in routine use. The re-          tory and interlaboratory measurements.
*        Volumes of tanks and containers should be established during initial installation and should be verified again following any physical changes that could alter the system configuration.


sults of these measurements should be recorded in a log and/or plotted on a control chart. Appropriate in-            The analysis of replicate samples provides a means vestigative and corrective action should be taken              to determine precision: the analysis of samples con- when the measurement value falls outside the pre-              taining known concentrations of radionuclides pro- determined control value.                                     vides a means to deter'mine accuracy. The analysis of laboratory blanks provides a means to detect and A check source for determining changes in count-            measure radioactive contamination of analytical sam- ing rate or counting efficiency should be of sufficient      ples, a common source of error in radiochemical radiochemical purity to allow correction for decay but        analysis of low-level samples. The analysis of analyt- need not have an accurately known disintegration              ical blanks also provides information on the adequacy rate, i.e., need not be a standard source.                    of background subtraction, particularly for samples measured by gamma-ray spectrometry.
Rev. 2 of RG 4.15, Page 13


For systems in which samples are changed manu- ally, check sources are usually measured daily. For              The fraction of the analytical effort needed for the systems with automatic sample changers, it may be             analysis of quality control samples depends to a large more convenient to include the check source within            extent on (I) the mixture of sample types in a particu- each batch of samples and thus obtain a measurement          lar laboratory in a particular time period and (2) the of this source within each counting cycle. For propor-       history of performance of that laboratory in the anal- tional counter systems, the plateau(s) should be              ysis of quality control samples. H6wever, in general checked after each gas change. Background meas-              it is found that at least 5%, and typically 10%, of the urements should be made frequently to ensure that            analytical load should consist of quality control levels arc within the expected range. For systems            samples.
*        The frequency of duplicates and REPLICATES5 should be established based on time (for continuous discharges) or number of batches (for batch discharges).
*       Sample integrity should be maintained through chain of custody procedures.


4.15-5
Procedures for continuous sampling should use methods that are designed to ensure that the sample is representative of the volumes being discharged.


6.3.1 IntralaboratoryAnalyses                              grams to provide an independent test of the ability to measure radionuclides at the very low concentrations Replicate samples, usually duplicates, should be            present in most environmental samples.
8.       Verification and Validation The V&V of certain aspects and support activities of the radiological measurement process or monitoring program are essential to the QA program. These aspects and activities include data and computer software V&V and project method validation.


analyzed routinely. These replicates should be pre- pared from samples that are as homogeneous as pos-                 The NRC Office of Inspection and Enforcement sible, such as well-stirred or mixed liquids (water or conducts a Ccnfirmatory Measurements Program for milk) and solids (dried, ground, or screened soil, sed- laboratories of licensees that measure nuclear reactor iment, or vegetation; or the ash of these materials).
Project method validation is the demonstration that a method (radioanalytical or radiation measurement) using performance-based method selection is capable of providing analytical results to meet a projects MQOs and any other criteria in the analytical protocol specification (APS). Acceptable method validation is necessary before the radiological analysis of samples or the taking of measurements in a monitoring program. Chapter 6 of MARLAP (Ref. 20) presents detailed guidance on project method validation for radioanalytical methods. In addition, Section 5.2.7 of ANSI N42.23-2003 (Ref. 22) and Section 5.4.5 of ISO/IEC 17025-2005 (Ref. 17) provide limited guidance for radioanalytical method validation.
                                                                effluents. The analyses of liquid waste holdup tank The size and other physical and chemical characteris-         samples, gas samples, charcoal cartridges, and stack tics of the replicate samples should be similar to particulate filters are included in this program. The those of single samples analyzed routinely.


results of the licensee's measurements of samples split with the NRC are compared to those of an NRC
Chapter 8 of MARLAP (Ref. 20) gives detailed guidance and applicable tools for the radioanalytical data V&V evaluation process as well as information for developing a data V&V plan, determining acceptable criteria and tests, and applying data qualifiers for radioanalytical data validation, as related to MQOs. EPA QA/G-8-2002 (Ref. 34) provides guidance for nonradioanalytical data V&V.
    The analysis of the replicate samples as blind re-         reference laboratory whose measurements are trace- plicates is desirable but is not practicable for all lab-      able to the National Bureau of Standards (Ref. 27).
oratories or for all types of samples. For example, in          Thus the results of this comparison provide to the small laboratories it may not be practicable to prevent        NRC an objective measure of the accuracy of the the analysts from being aware that particular samples          licensee's analyses.


are replicates of one another.
Computer programs used in the implementation of the radiological environmental monitoring program should be documented, verified, and validated before initial routine use and after each modification of the program. As described in Section 5.4.3.2 of MARLAP (Ref. 20), the laboratorys quality manual should include the criteria for computer software V&V and documentation. The software data reduction and reporting functions should be verified to perform as expected.6
9.      Assessments and Audits Assessments, audits, and surveillances are elements used to evaluate the initial and ongoing effectiveness of the QA program to monitor and control the quality of a radiological monitoring program.


Laboratories of licensees or their contractors that Obtaining true replicates of all types .of samples          perform environmental measurements should partici- also is not practicable. For example, obtaining repli-          pate in the EPA's Environmental Radioactivity Lab- cate samples of airborne materials usually is not prac-        oratory Intercomparison Studies (Cross-check) Pro- ticable on a routine basis because it requires either a        gram, or an equivalent program. This participation separate sampling system or splitting a single sample          should include all of the determinations (sample (e.g., cutting a filter in half). Use of replicate              medium/radionuclide combinations) that are both of- samplers usually is not economically feasible and               fered by EPA and included in the licensee's environ- splitting of samples results in replicates that do not          mental monitoring program. Participation in the EPA
Management having responsibility in the area being reviewed should document and review the results of these activities. Assessments that are independent of the day-to-day operations should be performed routinely, including management surveillance, peer reviews, and READINESS REVIEWS for new or revised systems and methods. Key performance indicators should be tracked and trended, with periodic management reporting. The QA program or project plan should outline the scope, frequency, and schedule of assessments, audits, and surveillances. A plan should be developed for each assessment audit or
represent the usual sample size or measurement con-            program provides an objective measure of the accu- figuration (counting geometry) for direct measure-              racy of the analyses because the EPA measurements ment. However, simulated samples of airborne mate-              are traceable to the National Bureau of Standards. If rials may be prepared in replicate and submitted for            the mean result of a cross-check analysis exceeds the analysis as unknowns.                                          control limit as defined by EPA (Ref. 28), an investi- gation should be made to determine the reason for Analysis of intralaboratory blank and spiked sam-          this deviation and corrective action should be taken ples is an important part of each laboratory's quality          as necessary. Similarly, an investigation and any control program. A known analytical blank sample                necessary corrective action should take place if the should be analyzed with each group of unknown                  "normalized range." as calculated by EPA, exceeds samples that is processed radiochemically to deter-            the control limit, as defined by EPA. A series of re- mine a specific radionuclide or radionuclides. Spiked          sults that is within the control limits but that exhibits and blank samples should be submitted for analysis              a trend toward these limits may indicate a need for an as unknowns to provide an intralaboratory basis for            investigation to determine the reason for the trend.
5 Replicate samples may be prepared by removing separate ALIQUANTS from the same grab sample.


estimating the accuracy of the analytical results.
6 The Institute of Electrical and Electronics Engineers (IEEE) Standard 1063, IEEE Standard for Software User Documentation (Ref. 35); EPA Directive 2185, Good Automated Laboratory Practices (Ref. 36); Subpart 2.7 of ASME NQA-1-1994 (Ref. 11); Regulatory Guide 1.168, Verification, Validation, Reviews, and Audits for Digital Computer Software Used Safety Systems of Nuclear Power Plants (Ref. 37); and Section 8 of ANSI N42.14-1999, Calibration and Use of Germanium Spectrometers for the Measurement of Gamma-Ray Emission Rates of Radionuclides (Ref. 38), also provide guidelines on software V&V.


These blanks and spikes may include blind replicates.
Rev. 2 of RG 4.15, Page 14


6.4 Compuitational Checks
surveillance for each area of the monitoring program being evaluated. A report of these activities should be generated according to the outline, format, and content established in the plan.
    6.3.2 InterlaboratvryAnalyses                                  Procedures for the computation of the concentra- tion of radioactive materials should include the inde- Analysis of effluent and environmental samples              pendent verification of a substantial fraction of the split with one or more independent laboratories is an          results of the computation by a person other than the important part of the quality assurance program be-            one performing the original computat'on. For com- cause it provides a means to detect errors that might          puter calculations, the input data should be verified not be detected by intralaboratory measurements                by a knowledgeable individual. All computer pro- alone. When possible, these independent laboratories            grams should be documented and verified before ini- should be those whose measurements are traceable to             tial routine use and after each modification of the NBS (Ref. 27).                                                  program. The verification process should include ver- ification, by a knowledgeable individual, of the al- Analysis of split field samples, such as samples of        gorithm used and test runs in which the output of the milk, water, soil or sediment, and vegetation, is par-          computer computation for given input can be com- ticularly important in environmental monitoring pro-            pared to "true" values that are known or determined
                                                          4.15-6


independently of the computer calculation. Documen-           under which the system will be optrated. These flow tation of the program should include a description of          rate devices should be recalibrated periodically.
Only qualified QA staff (see Regulatory Position 2, above), supported as needed by experts in the technical areas under evaluation, should conduct assessments, audits, and surveillances. (See ASME
NQA-1-1994, Supplement 2S, Ref. 11.) Deficiencies, areas for improvement, and observations noted should be incorporated into the corrective action program and tracked. Section 18 of ASME NQA-1-1994 (Ref. 11) and Section 4.10 of ISO/IEC 17025-2005 (Ref. 17) provide guidance on establishing and conducting an audit program.


the algorithm and a current listing of the program.
When the monitoring program will depend upon the services of a radioanalytical laboratory, prior onsite audits of the laboratory may be conducted to ensure that the laboratory is capable of fulfilling the project criteria in accordance with the APS (including MQOs) outlined in a statement of work (MARLAP
Chapter 5 and Appendix E). The ongoing evaluation of the laboratorys QUALITY SYSTEM and operations is accomplished through onsite audits and desk audits. These audits are focused more on whether the laboratory is meeting project or program specifications than whether the laboratory has the capability to meet monitoring program or project criteria. Chapter 7 of MARLAP provides guidance and statistical tests to determine whether a laboratory is meeting the MQOs, especially the REQUIRED METHOD UNCERTAINTY.


Guidelines for the documentation of digital computer              Whenever practicable, a check source that is ac- programs are given in ANSI N413-1974 (Ref. 29).               tuated remotely should be installed for integrity cheeks of the detector and the associated electrical
Section 5.2.10 of ANSI N42.23-2003 provides additional guidance for radioanalytical laboratory assessments.
7. Quality Control for Continuous Effluent                    system.


Monitoring Systems                                        8. Review, Analysis, and Reporting Data The specified frequency of calibration for a par-             Procedures for review, analysis, and reporting of ticular system should he based on considerations of the       data should include examinatiuns for reasonableness nature and stability of that system. For nuclear power       and consistency of the data and investigative and plants, specific requirements for calibrations and corrective actions to be taken under specified checks of particular effluent monitoring systems usu-        circumstances.
Audits of the QA programs of contractors providing materials, supplies, or services affecting the quality of the laboratorys operations should be performed periodically (Section 4.6 of ISO/IEC 17025-
2005, Ref. 17).
10.     Preventive and Corrective Actions Integral components of a QA program include identifying areas for improvement, defining performance or programmatic deficiencies, and initiating appropriate corrective or preventive actions. The QA program for radiological effluent and environmental monitoring programs should contain both a continuous-improvement program and a program for implementing corrective actions when conditions adverse to quality have been identified. In addition, needed improvements and potential sources of nonconformance should be identified and reported as part of a preventive action initiative of the continuous-improvement program (ISO/IEC 17025-2005, Sections 4.10-4.12)  for example, a condition- reporting program. Investigations should be initiated for degrading conditions, and corrective actions should be taken when conditions fall outside quality or regulatory acceptance criteria. For conditions that are adverse to quality, the corrective action process includes the following basic elements:
*       identification and documentation
*        classification
*        cause analysis
*        corrections
*        followup
*        closure Findings and corrective actions should be documented, tracked, and reported to management.


ally are included in the technical specifications for the plant.                                                    9. Audits Initial calibration of each measuring system should          Planned and periodic audits should be made to ver- be performed using one or more of the reference                ify implementation of the quality assurance program.
Followup reviews should be performed to verify the effectiveness and adequacy of the corrective actions.


standards that are certified by the National Bureau of       The audits should be performed by qualified indi- Standards or that are calibrated by a measurement            viduals who do not have direct responsibilities in the system that is traceable to that of the National Bureau      areas being audited.
Section 2.10 of ANSI/ASQC E4-1994 (Ref. 21) provides specifications and guidelines for developing the process, programs, and procedures necessary to detect and correct items of nonconformance and for implementing continuous quality improvement.


of Standards (Ref. 27). For nuclear power plants, Audit results should be documented and reviewed these calibrations are usually repeated at least annu- by management having responsibility in the area au- ally. The radionuclide standards should permit calib- dited. Followup action, including reaudit of deficient rating the system over its intended range of energy areas, should be taken where indicated.
Rev. 2 of RG 4.15, Page 15


and rate capabilities. Periodic inplant calibration should be performed using a secondary source or                             
When conducting an audit or surveillance of laboratory services, a prime area of review should be the effectiveness of the laboratorys corrective action program (Section 7.4.2 of MARLAP, Ref. 20).
Section 4.11 of ISO/IEC 17025-2005 (Ref. 17) provides general guidance on preventive and corrective action programs for laboratories. Annex C of ANSI N42.23-2003 (Ref. 22) provides additional guidance that should be considered in developing a corrective action program, including root cause analysis for radioanalytical services.


==D. IMPLEMENTATION==
==D. IMPLEMENTATION==
method that has been related to the initial calibration.
The purpose of this section is to provide information to licensees regarding the NRC staffs plans for using this regulatory guide. No backfit is intended or approved in connection with its issuance.


For nuclear power plants, these calibrations are usu-            The purpose of this section is to provide informa- ally performed at least monthly.                              tion to applicants and licensees regarding the NRC
Non-nuclear power reactor applicants and licensees may continue to use Revision 1 of Regulatory Guide 4.15, dated February 1979, or may adopt other procedures or practices that reflect generally accepted standards for ensuring quality in environmental data collected for effluent monitoring purposes. Except in those cases in which a nuclear power reactor applicant or licensee proposes or has previously established an acceptable alternative method for complying with specified portions of the NRCs regulations, the methods and practices described in this guide will be used in evaluating QA practices for environmental radiological monitoring programs.
                                                              staff's plans for using this regulatory guide.


Periodic correlations should be made during opera- This guide reflects current NRC staff practice.
Rev. 2 of RG 4.15, Page 16


tion to relate monitor readings to the concentrations Therefore, except in those cases in which the appli- and/or release rates of radioactive material in the monitored release path. These correlations should be          cant or licensee proposes an acceptable alternative method, the staff will use the method described based on the results of analyses for specific radionuc- herein in evaluating an applicant's or licensee's ca- lides in grab samples from the release path.
GLOSSARY7 accuracyThe closeness of a measured result to the true value of the quantity being measured.


pability for and performance in complying with spec- Flow-rate measuring devices associated with the           ified portions of the Commission's regulations until system should be calibrated to determine actual flow          this guide is revised as a result of suggestions from rates at the conditions of temperature and pressure            the public or additional staff review.
Various recognized authorities have given the word accuracy different technical definitions, expressed in terms of bias and imprecision. Following the Multi-Agency Radiological Laboratory Analytical Protocols (MARLAP) Manual (Ref. 20), the U.S. Nuclear Regulatory Commission (NRC) avoids all of these technical definitions and uses the term accuracy in its common, ordinary sense, which is consistent with the definition established by the International Organization for Standardization (ISO) in the International Vocabulary of Basic and General Terms in Metrology (Ref. 39).
aliquantA representative portion of a homogeneous SAMPLE removed for the purpose of analysis or other chemical treatment. The quantity removed is not an evenly divisible part of the whole sample. An aliquot, by contrast, is an evenly divisible part of the whole.


4.15-7
analyteSee TARGET ANALYTE.


REFERENCES
analytical protocol specification (APS)The output of a DIRECTED PLANNING PROCESS that contains the projects analytical data needs and criteria in an organized, concise form. The level of specificity in the APS should be limited to those criteria that are considered essential to meeting the projects analytical data criteria to allow the laboratory the flexibility of selecting the protocols or methods that meet the analytical criteria.
  I. Section 6.2, "Validation of Analyses," Chapter        Interface 5 (#4), 49-62 (1976). Also available from
 
6, "Validity of Results," Methods of Radiochewnical       the Superintendent of Documents, U.S. Government Analysis, World l-ealth Organization, Geneva, 1966.        Printing Office, Washington, D.C. 20402, as NBS
as low as reasonably achievable (ALARA)As low as is reasonably achievable taking into account the state of the technology and the economics of improvements in relation to benefits to the public health and safety and other societal and socioeconomic considerations, and in relation to the use of atomic energy in the public interest [10 CFR 50.34a(a)].
                                                          Technical Note #929, October 1976, C 13.46:929,
assessmentA planned and documented activity performed to determine whether various elements within a quality management system are effective in achieving stated quality objectives (ANSI N42.23-
2. "Analytical Quality Control Methods," Environ-        S/N 003.003-01694-2.
        2003, Ref. 22).
auditA planned and documented activity performed to determine by investigation, examination, or evaluation of objective evidence the adequacy of, and CONFORMANCE with, established procedures, instructions, drawings, and other applicable documents as well as the effectiveness of implementation. An audit should not be confused with surveillance or inspection activities performed for the sole purpose of process control or product acceptance (after ANSI N42.23-2003, Ref. 22).
background, instrumentRadiation detected by an instrument when no SOURCE is present. The background radiation that is detected may come from radionuclides in the materials of construction of the detector, its housing, its electronics, and the building as well as the environment and natural radiation.
 
background levelA term that usually refers to the presence of radioactivity or radiation in the environment. From an analytical perspective, the presence of background radioactivity in samples
7 Certain terms included in this glossary are not used in the main body of this regulatory guide, but are included because they are used within other definitions.
 
Rev. 2 of RG 4.15, Page 17
 
needs to be considered when clarifying the radioanalytical aspects of the decision or study question. Many radionuclides are present in measurable quantities in the environment.
 
bias (of a measurement process)A persistent deviation of the mean measured result from the true or accepted reference value of the quantity being measured, which does not vary if a measurement is repeated.
 
blank (analytical or method)A SAMPLE that is assumed to be essentially free of the TARGET ANALYTE
        (the unknown), that is carried through the radiochemical preparation, analysis, mounting, and measurement process in the same manner as a routine sample of a given matrix.
 
blind sampleA SAMPLE with a concentration not known to the analyst. Blind samples are used to assess analytical performance. A double-blind sample is a sample whose concentration and identity as a sample is known to the submitter, but not to the analyst. The analyst should treat the double-blind sample as a routine sample, so it is important that the double-blind sample is identical in appearance to routine samples.
 
calibrationThe set of operations that establish, under specified conditions, the relationship between values indicated by a measuring instrument or measuring system, or values represented by a material measure, and the corresponding known value of a parameter of interest.
 
calibration sourceA prepared SOURCE, made from a CERTIFIED REFERENCE MATERIAL OR STANDARD
        REFERENCE MATERIAL, that is used for calibrating instruments.
 
certified reference materialA reference material, accompanied by a certificate, with one or more property values certified by a procedure that establishes its traceability to an accurate realization of the unit in which the property values are expressed, and for which each certified value is accompanied by an UNCERTAINTY at a stated level of confidence (ISO Guide 30, Ref. 40). See STANDARD REFERENCE MATERIAL.
 
chain of custodyProcedures that provide the means to trace the possession and handling of a sample from collection to data reporting.
 
check sourceA material used to validate the operability of a radiation measurement device, sometimes used for instrument quality control. See TEST SOURCE and SOURCE, RADIOACTIVE.
 
condition adverse to quality an all-inclusive term used in reference to any of the following: failures, malfunctions, deficiencies, defective items, and nonconformances. A significant condition adverse to quality is one which, if uncorrected, could have a serious effect on safety or operability.
 
conformanceAn affirmative indication or judgment that a product or service has met the criteria of the relevant specifications, contract, or regulation; also the state of meeting the criteria (ANSI/ASQC
        E4-1994, Ref. 21).
corrective actionsThose measures taken to prevent, rectify, or eliminate conditions adverse to quality or detected nonconformities and  as necessary  to preclude repetition of those conditions.
 
data quality objective (DQO)Qualitative and quantitative statements that clarify the study objectives, define the most appropriate type of data to collect, determine the most appropriate conditions from which to collect the data, and specify tolerable limits on decision error rates. Because DQOs will be used to establish the quality and quantity of data needed to support decisions, they should Rev. 2 of RG 4.15, Page 18
 
encompass the total UNCERTAINTY resulting from all data collection activities, including analytical and sampling activities.
 
directed planning processA systematic framework focused on defining the data needed to support an informed decision for a specific project. Directed planning provides a logic for setting well- defined, achievable objectives and developing a cost-effective, technically sound sampling and analysis design that balances the data users tolerance for UNCERTAINTY in the decision process and the available resources for obtaining data to support a decision. Directed planning helps to eliminate unnecessary, poor, or inadequate sampling and analysis designs.
 
dose equivalentQuantity that expresses all radiations on a common scale for calculating the effective absorbed dose. This quantity is the product of absorbed dose (GRAYS (Gy) or rads) multiplied by a quality factor and any other modifying factors (MARSSIM, Ref. 28). The quality factor adjusts the absorbed dose because not all types of ionizing radiation create the same effect on human tissue.
 
For example, a dose equivalent of one SIEVERT (Sv) requires 1 Gy of beta or gamma radiation, but only 0.05 Gy of alpha radiation or 0.1 Gy of neutron radiation. Because the sievert is a large unit, radiation doses often are expressed in milliSIEVERTS (mSv). See TOTAL EFFECTIVE DOSE
        EQUIVALENT.
 
duplicate, fieldTwo samples of the same material, collected at the same location at the same time and under the same conditions, which are used to verify representativeness of the sampled material.
 
duplicate, laboratoryTwo ALIQUANTS of a SAMPLE, which are prepared and analyzed separately as part of the same batch, used in the laboratory to measure the overall PRECISION of the sample measurement process, beginning with laboratory subsampling of a field SAMPLE.
 
field duplicateSee DUPLICATE, FIELD.
 
graded approachA process of basing the level of management controls applied to an item or work on the intended use of the results and the degree of confidence needed in the quality of the results.
 
The NRC follows a graded approach to project planning and QUALITY ASSURANCE because of the diversity of environmental data collection activities. This diversity in the type of project and the data to be collected impacts the content and extent of the detail to be presented in the project planning documents.
 
gray (Gy)The International System of Units (SI) unit for absorbed radiation dose. One Gy is 1 joule of energy absorbed per kilogram of matter, equal to 100 RAD. See SIEVERT.
 
laboratory control sampleA standard material of known composition or an artificial SAMPLE (created by fortification of a clean material similar in nature to the sample), which is prepared and analyzed in the same manner as the sample. In an ideal situation, the result of an analysis of the laboratory control sample should be equivalent to (give 100 percent of) the TARGET ANALYTE concentration or activity known to be present in the fortified sample or standard material. The result normally is expressed as percent recovery. See also QUALITY CONTROL SAMPLE.
 
laboratory duplicateSee DUPLICATE, LABORATORY.
 
matrix spikeSee SPIKE.
 
Rev. 2 of RG 4.15, Page 19
 
measurement quality objective (MQO)The analytical data criteria of the DATA QUALITY OBJECTIVES,
      which are project- or program-specific and can be quantitative or qualitative. These analytical data criteria serve as measurement performance criteria or objectives of the analytical process.
 
MARLAP (Ref. 20) refers to these performance objectives as MQOs. Examples of quantitative MQOs include statements of required analyte detectability and the UNCERTAINTY of the analytical protocol at a specified radionuclide concentration, such as the action level. Examples of qualitative MQOs include statements of the required specificity of the analytical protocol (e.g., the ability to analyze for the radionuclide of interest (or TARGET ANALYTE) given the presence of interferences).
method uncertaintyReference to the predicted UNCERTAINTY of the result that would be measured if the method were applied to a hypothetical laboratory SAMPLE with a specified analyte concentration.
 
Although individual measurement uncertainties will vary from one measured result to another, the REQUIRED METHOD UNCERTAINTY is a target value for the individual measurement uncertainties and is an estimate of uncertainty before the sample is actually measured. See also UNCERTAINTY and REQUIRED METHOD UNCERTAINTY.
 
method validationThe demonstration that the method selected for the analysis of a particular analyte in a given matrix is capable of providing analytical results to meet the projects MEASUREMENT
      QUALITY OBJECTIVES and any other criteria in the ANALYTICAL PROTOCOL SPECIFICATIONS.
 
Compare with data and software VALIDATION.
 
minimum detectable concentrationThe minimum detectable value of the analyte concentration in a sample. The smallest (true) value of the net state variable that gives a specified probability that the value of the response variable will exceed its critical value (i.e., that the material analyzed is not blank).
minimum quantifiable concentrationMinimum quantifiable value of the analyte concentration, defined as the smallest concentration of analyte whose presence in a laboratory SAMPLE ensures that the relative standard deviation of the measurement does not exceed a specified value, usually 10
       percent.
 
nonconformancea deficiency in characteristic, documentation, or procedure that renders the quality of an item or activity unacceptable or indeterminate performance-based approachDefinition of the analytical data needs and criteria of a project in terms of measurable goals during the planning phase of a project. In a performance-based approach, the project-specific data objectives that are determined during a DIRECTED PLANNING PROCESS serve as measurement performance criteria for selections and decisions regarding the conduct of the laboratory analyses. The project-specific analytical data objectives are also used for the initial, ongoing, and final evaluation of the laboratorys performance and the laboratory data. In method selection, a performance-based approach is the process wherein a validated method is selected based on a demonstrated capability to meet defined quality and laboratory performance criteria.
 
performance evaluation (PE) programA laboratorys participation in an internal or external program of analyzing performance-testing samples appropriate for the analytes and matrices under consideration (i.e., PE program traceable to a national standards body, such as the National Institute of Standards and Technology (NIST) in the United States). Reference-material samples used to evaluate the performance of the laboratory are called performance-evaluation or performance-testing samples or materials. See CERTIFIED REFERENCE MATERIAL and STANDARD
       REFERENCE MATERIAL.
 
Rev. 2 of RG 4.15, Page 20
 
performance indicatorInstrument- or protocol-related parameter routinely monitored to assess the laboratorys estimate of controls such as chemical yield, instrument background, UNCERTAINTY,
        PRECISION, and BIAS. See BACKGROUND, INSTRUMENT.
 
performance testingSee PERFORMANCE EVALUATION PROGRAM.
 
precisionThe closeness of agreement between independent test results obtained by applying the experimental procedure under stipulated conditions. Conversely, imprecision is the variation of the results in a set of REPLICATE measurements. Precision may be expressed as the standard deviation (IUPAC, Ref. 41).
quality assurance (QA)An integrated system of management activities involving planning, implementation, assessment, reporting, and quality improvement to ensure that a process, item, or service is of the type and quality needed and expected. Quality assurance includes QUALITY
        CONTROL.
 
quality assurance project plan (QAPP)A formal document describing in detail the necessary QUALITY
        ASSURANCE, QUALITY CONTROL, and other technical activities that must be implemented to ensure that the results of the work performed will satisfy the stated performance criteria. The QA project plan describes policy, organization, and functional activities and the DATA QUALITY OBJECTIVES
        and measures necessary to achieve adequate data for use in selecting the appropriate remedy.
 
quality control (QC)The overall system of technical activities that measures the attributes and performance of a process, item, or service against defined standards to verify that they meet the stated objectives established by the project; operational techniques and activities that are used to fulfill objectives for quality. This system of activities and checks is used to ensure that measurement systems are maintained within prescribed limits, providing protection against out-of- control conditions and ensuring that the results are of acceptable quality.
 
quality control (QC) sampleAn uncontaminated SAMPLE matrix spiked with known amounts of analytes from a source independent of the calibration standards.
 
quality systemA structured and documented management system describing the policies, objectives, principles, organizational authority, responsibilities, accountability, and implementation plan of an organization for ensuring quality in its work processes, products (items), and services. The quality system provides the framework for planning, implementing, and assessing the work performed by an organization and for carrying out required QUALITY ASSURANCE and QUALITY CONTROL
         activities (ANSI/ASQC E4-1994, Ref. 21).
readiness reviewThe formal process of performing a written or verbal assessment of key attributes of a program or project measured against defined minimum criteria, standards, or quality metrics before initiation of activities under that project or program.
 
recordA retrievable document that furnishes objective evidence of the quality of products, services, or activities and that has been verified and authenticated as technically complete and correct.
 
remThe common unit for the effective or equivalent dose of radiation received by a living organism, equal to the actual dose (in rads) multiplied by a factor representing the danger of the radiation.
 
Rem is an abbreviation for roentgen equivalent man, meaning that it measures the biological effects of ionizing radiation in humans. One rem is equal to 0.01 Sv. See SIEVERT and DOSE EQUIVALENT.
 
Rev. 2 of RG 4.15, Page 21
 
replicatesTwo or more ALIQUANTS of a homogenous SAMPLE whose independent measurements are used to determine the PRECISION of laboratory preparation and analytical procedures.
 
reproducibilityThe closeness of the agreement between the results of measurements of the same parameter carried out under changed conditions of measurement. A valid statement of reproducibility depends upon specification of the conditions changed. The changed conditions may include principle of measurement, method of measurement, observer (or analyst), measuring instrument, reference standard, location, conditions of use, and time. Reproducibility may be expressed quantitatively in terms of the dispersion characteristics of the results. Results are usually understood to be corrected results.
 
required method uncertainty (uMR)METHOD UNCERTAINTY at a specified concentration. This is a key MEASUREMENT QUALITY OBJECTIVE.
 
sample(1) A portion of material selected from a larger quantity of material, or (2) a set of individual samples or measurements drawn from a population whose properties are studied to gain information about the entire population.
 
sievert (Sv)The Systme International (SI) unit for the effective dose of radiation received by a living organism. This unit represents the actual dose received (GRAYS in SI or rads in traditional units)
        times a factor that is larger for more dangerous forms of radiation. One Sv is 100 REM. Radiation doses are often measured in mSv. An effective dose of 1 Sv requires 1 GRAY of beta or gamma radiation, but only 0.05 Gy of alpha radiation or 0.1 Gy of neutron radiation.


mental Radioactivity Surveillance Guide, U.S. En-          14. Tritium Measure.'ent Techniques, Report of vironniental Protection Agency Report, ORP/SID
source, radioactiveA quantity of material configured for radiation measurement.
72-2, June 1972.                                          NCRP SC-36, NCRP Report No. 47, 1976.


3. Environmental Ra,.'iation Measurements, Report          15. "Guide to Sampling Airborne Radioactive Mate- of NCRP SC.35, NCRP Report No. 50, 1976.                  rials in Nuclear Facilities," ANSI N 13.1-1969.
spikeA known amount of TARGET ANALYTE added to the environmental sample to establish whether the method or procedure is appropriate for the analysis of the particular matrix and how the TARGET
        ANALYTE responds when the environmental sample is prepared and measured, thereby estimating the bias introduced by the sample matrix. Also termed MATRIX SPIKE.


4. Regulatory Guide 1.21, "Measuring, Evaluating,          16. "Specification and Performance of On-Site In- and Reporting Radioactivity in Solid Wastes and Re-        strumentation for Continuously Monitoring Radioac- leases of Radioactive Materials in Liquid and Gase-      tivity in Effluents," ANSI N13.10-1974.
standard reference materialA CERTIFIED REFERENCE MATERIAL issued by NIST in the United States.


ous Effluents from Light-Water-Cooled Nuclear              17. Air Sampling Instruments for Evaluation of At- Power Plants."                                            mospheric Contaminants, Fourth Edition, American
NIST certifies a standard reference material for specific chemical or physical properties and issues it with a certificate that reports the results of the characterization and indicates the intended use of the material.
5. Regulatory Guide 4.5, "Measurements of                 Conference of Industrial Hygienists, 1972.


Radionuclides in the Environment-Sampling and
surveillanceContinual or frequent monitoring and verification of the status of an activity and the analysis of records to ensure that specified requirements are being fulfilled. A surveillance is less extensive and more frequent than an AUDIT and concentrates on a single item or activity.
                                                            18. Users' Guide for Radioactivity Standards. Sub- Analyses of Plutonium in Soil."
                                                          committee on Radiochemistry and Subcommittee on
6. Regulatory Guide 4.6, "Measurements of                 the Use of Radioactivity Standards, Committee on Radionuclides in the Environment-Strontium-89 and          Nuclear Science, National Academy of Sciences- Strontium-90 Analyses."                                    National Research Council Report, NAS-NS-3115, February 1974.


7. Regulatory Cuide 4.13, "Performance, Testing, and Procedural Specifications for Thermolumines-            19. Environmental Impact Monitoring for Nuclear cence Dosimetry: Environmental Applications."              Power Plants, Source Book of Monitoring Methods, Vol. I, Atomic Industrial Forum Report, AIF/
surveyA systematic evaluation and documentation of radiological measurements with a correctly calibrated instrument or instruments that meet the sensitivity required by the objective of the evaluation.
8. HASL Procedures Manual, U.S. Energy Research NESP-004, February 1975.


and Development Administration Report, HASL-300,
target analyteA radionuclide on the list of radionuclides of interest or a radionuclide of concern for a project.
1972 (updated annually).                                  20. Instrumentation for Environmental Monitoring:
                                                          Radiation, Lawrence Berkeley Laboratory Report,
9. A Guide for Environmental Radiological Surveil-        LBL-l, Vol. 3, First Ed., May 1972; First update, lance at ERDA Installations, Energy Research and          February 1973; Second update, October 1973.


Development Administration Report, ERDA 77-24, March 1977.                                                21. C. W. Sill, "Problems in Sample Treatment in Trace Analysis." National Bureau of Standards Spe-
test sourceThe final radioanalytical processing product or matrix (e.g., precipitate, solution, filter) that is introduced into a measurement instrument. A test source is prepared from laboratory sample material for the purpose of determining its radioactive constituents. See CALIBRATION SOURCE,
10. Handbook of Radiochemical Analytical Methods,         cial Publication 4-22, Accuracy in Trace Analysis:
        CHECK SOURCE, and SOURCE, RADIOACTIVE.
U.S. Environmental Protection Agency Report,              Sampling, Sample Handling. and Analysis, pp. 463- EPA-680/4-75-001, February 1975.                          490, August 1976.


I1. Standard Methods for the Examination of Water        22. "General Principles for Sampling Airborne and Wastewater, Thirteenth Edition, American Pub-          Radioactive Materials," International Standard, lic Health Association, 1975.                              ISO-2889, 1975.
Rev. 2 of RG 4.15, Page 22


12. Handbookfor Sampling and Sample Preservation          23. Manual of Methods for Chemical Analysis of of Water and Wastewater, U.S. Environmental Pro-          Water and Wastes, EPA-625/6-74-003, U.S. En- tection Agency Report, Office of Research and De-          vironmental Protection Agency, Office of Technol- velopment, Environmental Monitoring Support Lab-          ogy Transfer, Washington, D.C. 20460, 1974.
total effective dose equivalent (TEDE)The sum of the effective dose equivalent (for external exposure)
        and the committed effective dose equivalent (for internal exposure), expressed in units of Sv or rem (MARSSIM, Ref. 28). See DOSE EQUIVALENT.


oratory, EPA-200/4-76-049. September 1976i
uncertaintyA parameter, usually associated with the result of a measurement, that characterizes the dispersion of the values that could reasonably be attributed to the measurement of interest (Chapter 19 of MARLAP, Ref. 20).
                                                          24. Annual Book of ASTM Standards (Part31), Wa-
validation(1) Data validation, the evaluation of data to determine the presence or absence of an analyte and to establish the UNCERTAINTY of the measurement process for contaminants of concern. Data validation qualifies the usability of each datum (after interpreting the impacts of exceptions identified during data VERIFICATION) by comparing the data produced with the MEASUREMENT
13. E. J. Maienthal and D. A. Becker, "A Survey on        ter, American Society for Testing and Materials, Current Literature on Sampling, Sample Handling,           Method D, 3370, pp. 71-82, Philadelphia, PA, July and Long-Term Storage for Environmental Materials,"        1975.
        QUALITY OBJECTIVES and any other analytical process criteria contained in the ANALYTICAL
        PROTOCOL SPECIFICATIONS developed in the planning process. (2) Software validation, the confirmation by examination and provision of objective evidence that the particular criteria for a specific intended use are fulfilled. Validation for a system is the set of activities ensuring and gaining confidence that the system is able to accomplish its intended use, goals, and objectives (ISO/IEC 15288-2002, Ref. 42).
verification(1) Data verification, a process that ensures that laboratory conditions and operations were compliant with the statement of work, sampling and analysis plan, and QUALITY ASSURANCE
        PROJECT PLAN and that identifies problems, if present, that should be investigated during data validation. Data verification compares the material delivered by the laboratory to these criteria (compliance) and checks for consistency and comparability of the data throughout the data package and for completeness of the results to ensure that all necessary documentation is available. (2)
        Software verification, the confirmation by examination and provision of objective evidence that specified criteria have been fulfilled. A set of activities compares a system life cycle product against the necessary characteristics for that product. The system life cycle products may include, but are not limited to, specified criteria, design description, and the system itself (ISO/IEC 15288-
        2002, Ref. 42).
                                          Rev. 2 of RG 4.15, Page 23


4.15-8
REFERENCES
1.  10 CFR Part 50, Domestic Licensing of Production and Utilization Facilities, U.S. Nuclear Regulatory Commission, Washington, DC.8
2.  10 CFR Part 52, Licenses, Certifications, and Approvals for Nuclear Power Plants, U.S. Nuclear Regulatory Commission, Washington, DC.8
3.  10 CFR Part 61, Licensing Requirements for Land Disposal of Radioactive Waste, U.S. Nuclear Regulatory Commission, Washington, DC.8
4. 10 CFR Part 72, Licensing Requirements for the Independent Storage of Spent Nuclear Fuel, High-Level Radioactive Waste, and Reactor-Related Greater Than Class C Waste, U.S. Nuclear Regulatory Commission, Washington, DC.8
5.  10 CFR Part 76, Certification of Gaseous Diffusion Plants, U.S. Nuclear Regulatory Commission, Washington, DC.8
6.  10 CFR Part 30, Rules of General Applicability to Domestic Licensing of Byproduct Material, U.S. Nuclear Regulatory Commission, Washington, DC.8
7.  10 CFR Part 40, Domestic Licensing of Source Material, U.S. Nuclear Regulatory Commission, Washington, DC.8
8.  10 CFR Part 70, Domestic Licensing of Special Nuclear Material, U.S. Nuclear Regulatory Commission, Washington, DC.8
9.  10 CFR Part 20, Standards for Protection Against Radiation, U.S. Nuclear Regulatory Commission, Washington, DC.8
10. 40 CFR Part 190, Environmental Radiation Protection Standards for Nuclear Power Operations, U.S. Environmental Protection Agency, Washington, DC.9
11. ASME NQA-1-1994, Quality Assurance Program Requirements for Nuclear Facilities (with Addenda), American Society of Mechanical Engineers, New York, NY, 1994.10
8 All NRC regulations listed herein are available electronically through the Public Electronic Reading Room on the NRCs public Web site, at http://www.nrc.gov/reading-rm/doc-collections/cfr/. Copies are also available for inspection or copying for a fee from the NRCs Public Document Room at 11555 Rockville Pike, Rockville, MD;
    the PDRs mailing address is USNRC PDR, Washington, DC 20555; telephone (301) 415-4737 or (800) 397-4209;
    fax (301) 415-3548; email PDR@nrc.gov.


25. Biological Field and Laboratory, Methods for          Standards and Measurements in Different Fields,"
9 This regulation is available electronically through the U.S. Environmental Protection Agencys public Web site, at http://www.epa.gov/epacfr40/chapt-I.info/.
Measuring the Quality of Surface Waters and              Nuclear Instruments and Methods, Vol. 112, pp.
10
    Purchase information is available through the American Society of Mechanical Engineers (ASME) Web site at http://catalog.asme.org/Codes/PrintBook/NQA1_1994_Quality_Assurance.cfm.


Effluents, EPA-670/4-73-001, Office of Research and      5-18, 1973.
Rev. 2 of RG 4.15, Page 24


Development, U.S. Environmental Protection Agency, Cincinnati, Ohio, July 1973.                     28. Environmental Radioactivity Laboratory Inter- comparison Studies Program, FY 1977, EPA-600/4.
12. Generic Letter 79065, Radiological Assessment Branch Technical Position on Radiological Environmental Monitoring, Revision 1, U.S. Nuclear Regulatory Commission, Washington, DC,
    November 27, 1979.11
13. Regulatory Guide 1.21, Measuring, Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive Materials in Liquid and Gaseous Effluents from Light-Water-Cooled Nuclear Power Plants, U.S. Nuclear Regulatory Commission, Washington, DC.12
14. Regulatory Guide 4.1, Programs for Monitoring Radioactivity in the Environs of Nuclear Power Plants, U.S. Nuclear Regulatory Commission, Washington, DC.12
15. Regulatory Guide 4.14, Radiological Effluent and Environmental Monitoring at Uranium Mills, U.S. Nuclear Regulatory Commission, Washington, DC.12
16. Regulatory Guide 4.16, Monitoring and Reporting Radioactivity in Releases of Radioactive Materials in Liquid and Gaseous Effluents from Nuclear Fuel Processing and Fabrication Plants and Uranium Hexafluoride Production Plants, U.S. Nuclear Regulatory Commission, Washington, DC.12
17. ISO/IEC 17025-2005, General Requirements for the Competence of Testing and Calibration Laboratories, International Standards Organization/International Electrotechnical Commission, Geneva, Switzerland, May 2005, Correction 1, August 2006.13
18. EPA QA/G-4-2006, Guidance on Systematic Planning Using the Data Quality Objectives Process, U.S. Environmental Protection Agency, Washington, DC, EPA 240/B-06/001, February 2006.14
19. EPA QA/G-5-2002, Guidance for Quality Assurance Project Plans, U.S. Environmental Protection Agency, Washington, DC, EPA/240/R-02/009, December 2002.14
20. NUREG-1576 (MARLAP), Multi-Agency Radiological Laboratory Analytical Protocols Manual, Volumes 1-3, U.S. Nuclear Regulatory Commission, Environmental Protection Agency, Department of Energy, Department of Defense, Department of Homeland Security, National
11 Generic Letter 79065 is available electronically through the NRCs public Web site at http://www.nrc.gov/reading-rm/
    doc-collections/gen-comm/gen-letters/1979/gl79065.html.


26. International Directory of Certified Radioactive      77-001, January 1977.
12 All regulatory guides listed herein were published by the U.S. Nuclear Regulatory Commission or its predecessor, the U.S. Atomic Energy Commission. Most are available electronically through the Electronic Reading Room on the NRCs public Web site, at http://www.nrc.gov/reading-rm/doc-collections/reg-guides/. Active guides may be purchased from the National Technical Information Service (NTIS). Details may be obtained by contacting NTIS at
    5285 Port Royal Road, Springfield, Virginia 22161, online at http://www.ntis.gov, by telephone at (800) 553-NTIS
    (6847) or (703) 605-6000, or by fax to (703) 605-6900. Copies are also available for inspection or copying for a fee from the NRCs Public Document Room (PDR), which is located at 11555 Rockville Pike, Rockville, Maryland; the PDRs mailing address is USNRC PDR, Washington, DC 20555-0001. The PDR can also be reached by telephone at
    (301) 415-4737 or (800) 397-4209, by fax at (301) 415-3548, and by email to PDR@nrc.gov.


Materials, International Atomic Energy Agency Re- port, STI/PUB/398, 1975.                                  29. "Guidelines for the Documentation of Digital
13 Copies of all ISO publications cited in this document may be purchased from ISO in Geneva, Switzerland.
27. L. M. Cavallo et al.. "Needs for Radioactivity        Computer Programs," ANSI N413- 1974.


4.15-9
Purchase information is available through the ISO Web site at http://www.iso.org/iso/en/ISOOnline.frontpage.


APPENDIX A
14 Copies of all EPA quality system publications are available for download free of charge from the EPA public Web site at http://www.epa.gov/quality/qa_docs.html.
                                                    GLOSSARY
A-ccurac'yv-normally refers to the difference (error or      electronic components of the system are operating bias) between tile mean, K. of the set of results and        correctly.


the value *. which is accepted as the true or correct Instrument Batckground--the response of the instru- value for the quantity measured. It is also used as the ment in the absence of a radioactive sample or other difference between an individual value X, and X.
Rev. 2 of RG 4.15, Page 25


radioactive source.
Institute of Standards and Technology, U.S. Geological Survey, and Food and Drug Administration, Washington, DC, July 2004.15
21. ANSI/ASQC E4-1994, Specifications and Guidelines for Quality Systems for Environmental Data Collection and Environmental Technology Programs, American National Standards Institute/American Society for Quality Control, New York, NY, 1994.16
22. ANSI N42.23-2003, Measurement and Associated Instrumentation Quality Assurance for Radioassay Laboratories, American National Standards Institute, New York, NY, 2003.16
23. NIRMA TG11, Authentication of Records and Media, Nuclear Information and Records Management Association, Inc., Windham, NH, 1998.17
24. NIRMA TG15, Management of Electronic Records, Nuclear Information and Records Management Association, Inc., Windham, NH, 1998.17
25. NIRMA TG16, Software Configuration Management and Quality Assurance, Nuclear Information and Records Management Association, Inc., Windham, NH, 1998.17
26. NIRMA TG21, Electronic Records Protection and Restoration, Nuclear Information and Records Management Association, Inc., Windham, NH, 1998.17
27. HPS/ANSI N13.1-1999, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stacks and Ducts of Nuclear Facilities, Health Physics Society (HPS), McLean, VA,
    1999.18
28. NUREG-1575 (MARSSIM), Multi-Agency Radiation Survey and Site Investigation Manual, Revision 1 (EPA 402-R-97-016 Revision 1, DOE/EH-0624 Revision 1), U.S. Nuclear Regulatory Commission, Environmental Protection Agency, Department of Energy, Washington, DC,
    August 2000.15
29. EPA QA/G-9S-2006, Data Quality Assessment: Statistical Tools for Practitioners, U.S.


Absolhte acciuracy of the mean is given by "-,*
Environmental Protection Agency, Washington, DC, EPA/240/B-06/003, February 2006.14
                                                              Precision-relates to the reproducibility (f meas- and of an individual value by XrT.
15 Copies are available electronically through NRCs public Web site at http://www.nrc.gov/reading-rm/doc-collections/
    nuregs/staff/sr1576/ and from EPAs public Web site at http://www.epa.gov/radiation/marlap/links.htm.


urements within a set, that is. to the scatter or disper- Relative accrwvr  of the mean is given by t.-,)/:.       son of a set about its central value.
16 Copies of all ANSI publications cited in this document may be purchased from the American National Standards Institute, 1819 L Street, NW, 6th floor, Washington, DC 20036. Purchase information is available through the ANSI
    Web site at http://webstore.ansi.org/ansidocstore/default.asp.


Pr'rcentageaccurac*y is given by 100 (X-0)/*.           Quality Assurance (QA )-(the planned and systematic actions that are necessary to provide adequate confi-
17 Copies of all NIRMA Technical Guidance documents cited herein may be purchased from the Nuclear Information and Records Management Association, Inc., 10 Almas Road, Windham, NH; telephone (603) 432-6476;
,Imd Vtic*'l Blank (Sample)-ideally. a sample having          dence in the results of a monitoring program.
    fax (603) 432-3024; see the NIRMA Web site at http://www.nirma.org/member/publications.htm.


all of the constituents of the unknown sample except those to be determined. In radioanalytical practice.          Quaitiy Control (QC)-those quality assurance ac- the term often refers it) the radiochemical processing        tions that provide a means to control and measure the of carrier(s) or tracers without the sample matrix ma-        characteristics of measurement equipment and proc- terial.                                                      esses to established requirements. Thus. quality as- surance includes quality control.
18 Copies of this standard are available for purchase from the HPS Web site at http://hps.org/hpssc/n13standards.html.


"Blind" Replivcat (Sample)-replicate samples that are not identified as replicates to the persons pcrform-      Spiketd Sample-a sample to which a known amount ing the analysis.                                             of radioactive material has been added. Generally.
Rev. 2 of RG 4.15, Page 26


spiked samples are submitted as unknowns to the Calibrainon-the process of determining the numeri- analysts.
30. ASTM D7282-2006, New Standard Practice for Setup, Calibration, and Quality Control of Instruments Used for Radioactivity Measurements, American Society for Testing and Materials, West Conshohocken, PA, 2006.19
31. ASTM MNL 7A-2002, Manual on Presentation of Data and Control Chart Analysis, 7th Edition, American Society for Testing and Materials, West Conshohocken, PA, 2002.19
32. ANSI N42.22-1995, Traceability of Radioactive Sources to the National Institute of Standards and Technology (NIST) and Associated Instrument Quality Control, American National Standards Institute, New York, NY, 1995 (R2002).16
33. ANSI N42.18-2004, American National Standard Specification and Performance of On-Site Instrumentation for Continuously Monitoring Radioactivity in Effluents, Institute of Electrical and Electronics Engineers, Inc., New York, NY, 1980 (R2004).16
34. EPA QA/G-8-2002, Guidance on Environmental Data Verification and Data Validation, U.S.


cal relationship between the observed output of a measurement system and the value, based on refer-            Split Sample-a sample that is divided into parts.
Environmental Protection Agency, Washington, DC, EPA/240/R-02/004, November 2002.14
35. IEEE 1063, IEEE Standard for Software User Documentation, Institute of Electrical and Electronics Engineers, Inc. (IEEE), Piscataway, New Jersey, December 2001.20
36. EPA Directive 2185, Good Automated Laboratory Practices, U.S. Environmental Protection Agency (EPA), Office of Information Resources Management, 1995.21
37. Regulatory Guide 1.168, Verification, Validation, Reviews, and Audits for Digital Computer Software Used in Safety Systems of Nuclear Power Plants, U.S. Nuclear Regulatory Commission, Washington, DC.12
38. ANSI N42.14-1999, Calibration and Use of Germanium Spectrometers for the Measurement of Gamma-Ray Emission Rates of Radionuclides, American National Standards Institute, New York, NY, 1999.16
39. International Organization for Standardization (ISO), International Vocabulary of Basic and General Terms in Metrology, 2nd Edition, Geneva, Switzerland, 1993.13
40. ISO Guide 30, Terms and Definitions Used in Connection with Reference Materials, International Organization for Standardization, Geneva, Switzerland, 1992.13
19 Copies of all ASTM standards cited herein may be purchased from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959; see the ASTM International Web-based standards search tool at http://www.astm.org/cgi-bin/SoftCart.exe/NEWSITE_JAVASCRIPT/index.shtml?L+mystore+qkyo3147+117461063.


ence standards, of the characteristics being measured.       each of which is analyzed independently by separate Calibration Source-any radioactive source that is            laboratory organizations.
20
    Copies of this standard are available for purchase from the IEEE Web site at http://standards.ieee.org/db/status/index.shtml.


used for calibration of a measurement system.
21 Copies of this directive are available electronically from the EPAs public Web site at http://www.epa.gov/irmpoli8/archived/irm_galp/.
                                            Rev. 2 of RG 4.15, Page 27


Standard (radioactive) Source-a radioactive source Check Source (or instrumnent check source, perform-          having an accurately known radionuclide content and anlce check source, or referJence source)-a radioac-         radioactive disintegration rate or particle or photon tive source used to determine if the detector and all        emission rate.
41. International Union of Pure and Applied Chemistry (IUPAC), Nomenclature for Radioanalytical Chemistry, Pure and Applied Chemistry, 66:12, pp. 2513-2526, 1994.22
42. ISO/IEC 15288-2002, System Engineering  System Life Cycle Processes, International Organization for Standardization, Geneva, Switzerland, 2002.13
22 Copies are available electronically through the IUPAC public Web site at http://www.iupac.org/publications/pac/1994/6612/index.html.


4.15-10}}
Rev. 2 of RG 4.15, Page 28}}


{{RG-Nav}}
{{RG-Nav}}

Revision as of 14:28, 13 March 2020

Quality Assurance for Radiological Monitoring Programs (Inception Through Normal Operations to License Termination) - Effluent Streams and the Environment
ML071790506
Person / Time
Issue date: 07/01/2007
From:
Office of Nuclear Regulatory Research
To:
Ridgely JN RES 415-6555
Shared Package
ML071790495 List:
References
DG-4010 RG-4.015, Rev 2
Download: ML071790506 (28)
v • d • e


U.S. NUCLEAR REGULATORY COMMISSION July 2007 Revision 2 REGULATORY GUIDE

OFFICE OF NUCLEAR REGULATORY RESEARCH

REGULATORY GUIDE 4.15 (Draft was issued as DG-4010, dated November 2006)

QUALITY ASSURANCE

FOR RADIOLOGICAL MONITORING PROGRAMS

(INCEPTION THROUGH NORMAL OPERATIONS

TO LICENSE TERMINATION)

EFFLUENT STREAMS AND THE ENVIRONMENT

A. INTRODUCTION

This regulatory guide describes a method that the U.S. Nuclear Regulatory Commission (NRC)

considers acceptable for use in designing and implementing programs to ensure the quality of the results of measurements of radioactive materials in the effluents from, and environment outside of, facilities that process, use, or store radioactive materials during all phases of the facilitys life cycle.

QUALITY ASSURANCE1 (QA) is a fundamental expectation of Title 10, Energy, of the Code of Federal Regulations (10 CFR) for items and activities that are relied on to protect the health and safety of the public and the environment.

This guide specifically applies to facilities for which NRC regulations require routine monitoring of radioactive effluents to the environment, and particularly those facilities licensed under the following regulations:

  • 10 CFR Part 50, Domestic Licensing of Production and Utilization Facilities (Ref. 1)
  • 10 CFR Part 52, Licenses, Certifications, and Approvals for Nuclear Power Plants (Ref. 2)

1 Special terms used in this guide are marked in SMALL CAPITALS the first time they are used, and are defined in the glossary provided in this regulatory guide.

The U.S. Nuclear Regulatory Commission (NRC) issues regulatory guides to describe and make available to the public methods that the NRC staff considers acceptable for use in implementing specific parts of the agencys regulations, techniques that the staff uses in evaluating specific problems or postulated accidents, and data that the staff need in reviewing applications for permits and licenses. Regulatory guides are not substitutes for regulations, and compliance with them is not required. Methods and solutions that differ from those set forth in regulatory guides will be deemed acceptable if they provide a basis for the findings required for the issuance or continuance of a permit or license by the Commission.

This guide was issued after consideration of comments received from the public.

Regulatory guides are issued in 10 broad divisions: 1, Power Reactors; 2, Research and Test Reactors; 3, Fuels and Materials Facilities; 4, Environmental and Siting; 5, Materials and Plant Protection; 6, Products; 7, Transportation; 8, Occupational Health;

9, Antitrust and Financial Review; and 10, General.

Electronic copies of this guide and other recently issued guides are available through the NRCs public Web site under the Regulatory Guides document collection of the NRCs Electronic Reading Room at http://www.nrc.gov/reading-rm/doc-collections/ and through the NRCs Agencywide Documents Access and Management System (ADAMS) at http://www.nrc.gov/reading-rm/adams.html, under Accession No. ML071790506.

  • 10 CFR Part 61, Licensing Requirements for Land Disposal of Radioactive Waste (Ref. 3)
  • 10 CFR Part 72, Licensing Requirements for the Independent Storage of Spent Nuclear Fuel, High-Level Radioactive Waste, and Reactor-Related Greater Than Class C Waste (Ref. 4)

The guide also may apply to other facilities licensed by the NRC, for which the agency may impose specific license conditions for effluent or environmental monitoring, as deemed necessary to ensure the health and safety of the public and the environment, including those licensed under the following regulations:

  • 10 CFR Part 30, Rules of General Applicability to Domestic Licensing of Byproduct Material (Ref. 6)

Finally, radiological standards for occupational workers and members of the public are codified in 10 CFR Part 20, Standards for Protection Against Radiation (Ref. 9).

Although the specific regulations provide the actual requirements, the following presents an overview of applicable NRC regulations addressing limits on radioactive effluents, environmental levels of radioactivity, requirements for effluent and environmental monitoring, and associated QA.

In accordance with 10 CFR 20.1301, Dose Limits for Individual Members of the Public, the TOTAL EFFECTIVE DOSE EQUIVALENT (TEDE) to individual members of the public from licensed operation must not exceed 1 milliSIEVERT [1 mSv, or 100 milliREM (mrem)] per year. Uranium fuel cycle facilities (excluding transportation and disposal) also must comply with the provisions that the U.S. Environmental Protection Agency (EPA) established in 40 CFR Part 190, Environmental Radiation Protection Standards for Nuclear Power Operations (Ref. 10). In addition, 10 CFR 20.1101(d) requires licensees (other than those subject to 10 CFR 50.34a, Design Objectives for Equipment to Control Releases of Radioactive Material in Effluents Nuclear Power Reactors, discussed below) to restrict releases of airborne radioactive materials so that the highest individual dose to the public will not exceed 0.1 mSv (10 mrem)

per year.

In addition, under 10 CFR 20.1101(b), licensees must apply AS LOW AS REASONABLY ACHIEVABLE

(ALARA) concepts to doses to occupational workers and members of the general public. In accordance with 10 CFR 20.1302, Compliance with Dose Limits for Individual Members of the Public, licensees must survey radiation levels to demonstrate compliance with the dose limits, and 10 CFR 20.1101, Radiation Protection Programs, requires licensees to develop, document, and implement radiation protection programs commensurate with the scope and extent of licensed activities and sufficient to ensure compliance with the provisions of 10 CFR Part 20 (Ref. 9).

In 10 CFR Part 20, Subpart E, Radiological Criteria for License Termination, the NRC provides the radiological criteria for license termination under unrestricted and restricted use scenario

s. The NRC

considers a site acceptable for unrestricted use if the residual radioactivity that is distinguishable from background radiation does not exceed 25 mrem/year (0.25mSv/year) TEDE to an average member of the critical group, including contributions from groundwater sources. A site can be released under restricted use if the residual radioactivity that is distinguishable from background dose not exceed a yearly dose of

25 mrem (0.25mSv) TEDE with site use restrictions in place.

Rev. 2 of RG 4.15, Page 2

For nuclear power reactors, 10 CFR 50.34a and 10 CFR 50.36a, Technical Specifications on Effluents from Nuclear Power Reactors, require ALARA concepts for operations to maintain releases of radioactive materials in effluents consistent with the guidelines of Appendix I, Numerical Guides for Design Objectives and Limiting Conditions for Operation to Meet the Criterion As Low As Is Reasonably Achievable for Radioactive Material in Light-Water-Cooled Nuclear Power Reactor Effluents, to

10 CFR Part 50. Licensees must also establish appropriate SURVEILLANCE and monitoring programs to provide QA with respect to (1) areas of equipment operation and (2) data on the quantities or concentrations of radionuclides released in liquid and gaseous effluents. These programs will help to ensure accurate projection of the levels of radiation and radioactive materials found in the environment.

Section III.B of Appendix I addresses requirements concerning estimates of radioactive iodine in water and food pathways if land use changes occur after plant construction.

The regulations in 10 CFR 30.34, Byproduct Material, 10 CFR 40.41, Source Material,

10 CFR 50.50, Production and Utilization Facilities, and 10 CFR 70.32, Special Nuclear Material, provide that the NRC may incorporate in any governed license such terms and conditions as it deems appropriate or necessary to protect health.

For land disposal of radioactive waste, 10 CFR 61.53, Environmental Monitoring, requires measurements and observations to be made and recorded to provide data to evaluate potential health and environmental impacts, including long-term effects, as well as the need for mitigating measures. The monitoring system must be capable of providing early warning of releases of radionuclides from the disposal site. A postclosure monitoring program is also required to detect the release of radionuclides.

According to 10 CFR 70.59, Effluent Monitoring Reporting Requirements, licensees authorized to possess and use special nuclear materials for processing and fuel fabrication, scrap recovery, conversion of uranium hexafluoride, or in a uranium enrichment facility shall report to the NRC the quantity of each of the principal radionuclides released to unrestricted areas in liquid and gaseous effluents, and other information as the Commission may require to estimate maximum potential annual radiation doses to the public resulting from effluent releases.

Appendix A, General Design Criteria for Nuclear Power Plants, to 10 CFR Part 50 includes several applicable general design criteria (GDC) affecting nuclear power plant designs. GDC 60, Control of Releases of Radioactive Materials to the Environment, requires suitable means to control the release of radioactive materials in gaseous and liquid effluents. GDC 64, Monitoring Radioactivity Releases, requires means for monitoring effluent discharge paths and the plant environs for radioactivity that may be released from normal operations, including anticipated operational occurrences, and from postulated accidents. GDC 1, Quality Standards and Records, requires the establishment of a QA program for those structures, systems, and components that are important to safety to provide adequate assurance that they will satisfactorily perform their safety functions. Appendix B, Quality Assurance Criteria for Nuclear Power Plants and Fuel Reprocessing Plants, to 10 CFR Part 50 establishes the QA requirements for power plants.

The requirements in 10 CFR 72.104, Criteria for Radioactive Material in Effluent and Direct Radiation from an ISFSI [Independent Spent Fuel Storage Installation] or MRS [Monitored Retrievable Storage], mandate operational restrictions for maintaining effluents and direct radiation levels in accordance with ALARA concepts, with limits so as not to exceed annual DOSE EQUIVALENTS of .25 mSv

(25 mrem) to the whole body, 0.75 mSv (75 mrem) to the thyroid, and 0.25 mSv (25 mrem) to any other critical organ of any real individual beyond the controlled area.

For gaseous diffusion uranium enrichment facilities, 10 CFR 76.87, Technical Safety Requirements, requires licensees to establish technical safety requirements with procedures and equipment Rev. 2 of RG 4.15, Page 3

to address (among other things) building and process ventilation and off-gassing, radioactive waste management, and environmental protection. In addition, 10 CFR 76.93, Quality Assurance, requires a QA program satisfying the applicable provisions of the American Society of Mechanical Engineers (ASME) standard QA-1-1994, Quality Assurance Program Requirements for Nuclear Facilities (with Addenda) (Ref. 11).

Generic Letter 79065 (Ref. 12), regarding the NRCs Radiological Assessment Branch Technical Position on Radiological Environmental Monitoring, provides guidance on the appropriate type of, and location for, sampling and monitoring the environment surrounding nuclear power plants.

This regulatory guide presents more complete and extensive guidance on QA for facilities where radiological effluent or environmental monitoring is required by NRC regulations.2 However, this guidance does not address all topics and elements that a facilitys QA program may require (such as requirements of Appendix B to 10 CFR Part 50 for nuclear power plants or 10 CFR 76.93 for gaseous diffusion uranium enrichment facilities).

The NRC issues regulatory guides to describe to the public methods that the staff considers acceptable for use in implementing specific parts of the agencys regulations, to explain techniques that the staff uses in evaluating specific problems or postulated accidents, and to provide guidance to applicants.

Regulatory guides are not substitutes for regulations, and compliance with regulatory guides is not required.

2 While not specific to QA, other regulatory guides that address measurements of radioactive materials in effluents and the environment include the following:

  • Regulatory Guide 1.21, Measuring, Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive Materials in Liquid and Gaseous Effluents from Light-Water-Cooled Nuclear Power Plants (Ref. 13)
  • Regulatory Guide 4.1, Programs for Monitoring Radioactivity in the Environs of Nuclear Power Plants (Ref. 14)
  • Regulatory Guide 4.16, Monitoring and Reporting Radioactivity in Releases of Radioactive Materials in Liquid and Gaseous Effluents from Nuclear Fuel Processing and Fabrication Plants and Uranium Hexafluoride Production Plants (Ref. 16)

Rev. 2 of RG 4.15, Page 4

B. DISCUSSION

As used in the context of this guide, QA comprises all those planned and systematic actions that are necessary to provide adequate confidence in the ASSESSMENT of monitoring result

s. QUALITY CONTROL

(QC) comprises those QA actions that provide a means to measure and control the characteristics of measurement equipment and processes to meet established standards; QA includes QC. This guide makes no further effort to distinguish those elements that may be considered QC from those composing QA.

Quality assurance is necessary to ensure that all radiological and nonradiological measurements that support the radiological monitoring program are reasonably valid and of a defined quality. These programs are needed (1) to identify deficiencies in the sampling and measurement processes and report them to those responsible for these operations so that licensees may take CORRECTIVE ACTION and (2) to obtain some measure of confidence in the results of the monitoring programs to assure the regulatory agencies and the public that the results are valid. All steps of the monitoring process should involve QA

(e.g., sampling, shipment of SAMPLES, receipt of samples in the laboratory, preparation of samples, radiological measurements, data reduction, data evaluation, and reporting of the measurement and monitoring results) .

An effective overall management system for quality must precede the design of a QA program. A

document by the International Organization for Standardization (ISO/IEC 17025-2005, Ref. 17) is available for use by laboratories in developing their management system for quality, administrative, and technical operations. Once a quality management system is in place, a DIRECTED PLANNING PROCESS can be used to define the data objectives for the specific monitoring program. The DATA QUALITY OBJECTIVE (DQO)

process (EPA QA/G-4-2006, Ref. 18) provides one example of how to develop and define acceptance and performance criteria for a sample collection, measurement, and data analysis progra

m. The QUALITY

ASSURANCE PROJECT PLAN (QAPP), which documents how data will be collected, assessed, and analyzed, can form the basis of a QA program (EPA QA/G-5-2002, Ref. 19). The QAPP provides a blueprint of where, when, why, and how a particular project will achieve data of the type and quality needed and expected.

NUREG-1576, Multi-Agency Radiological Laboratory Analytical Protocols Manual (Ref. 20,

hereafter referred to as MARLAP), contains guidance for developing DQOs for risk-informed decisions, and their consequent MEASUREMENT QUALITY OBJECTIVES (MQOs), in the context of radiochemical analyses of environmental samples. The same methodology can be applied in other environmental monitoring contexts. An example of a key MQO is the REQUIRED METHOD UNCERTAINTY at a specified radiation dose or radionuclide concentration. The specific dose may be a fractional amount of a radiation dose limit. The specific concentration may be a fractional amount of an effluent release or environmental radionuclide concentration. For either case, the fractional amount of the limit should be sufficiently small so that a licensee may take reasonable operational actions before the limit is exceede

d. MARLAP

recommends a PERFORMANCE-BASED APPROACH for selecting methods used to analyze samples or measure dose rates that meet the MQOs. Under this approach, the licensees QA program should incorporate the initial (project METHOD VALIDATION) and continued [internal and external PERFORMANCE EVALUATION (PE)

PROGRAMS] assessment of a methods capability to meet the MQO specifications. Process-radiation monitoring equipment and instrumentation need to have the desired sensitivity to provide both real-time and data-trend values that can correlate to the actual measurements of process streams before release. The radiological environmental measurements program may be used to confirm the adequacy of the process- monitoring equipment.

Rev. 2 of RG 4.15, Page 5

C. REGULATORY POSITION

The QA program of each organization performing radiological effluent or environmental monitoring of nuclear facilities using, processing, or storing radioactive materials during all phases of the facilitys life cycle should be documented by written policies and procedures. Licensees should have sufficient RECORDS of program conduct and performance to demonstrate program adherence. In addition to its own program, a licensee should require any contractor or subcontractor performing support program activities (e.g., sampling, analysis, evaluations, and records) retain records sufficient for the licensee to develop and maintain a QA program covering the applicable program elements.

The following presents the QA program elements that should be developed and implemented to ensure the quality of data/results for radiological effluent and environmental monitoring programs.

1. Organizational Structure and Responsibilities of Managerial and Operational Personnel The structure of the organization as it relates to the management and operation of the monitoring programs, including QA policy and functions, should be defined and documented. The authorities, duties, and responsibilities of the positions within this organization, down to the first-line supervisory level, should be described. This should include responsibilities for review and approval of written procedures and the preparation, review, and evaluation of monitoring data and reports.

Persons and organizations performing QA functions should have sufficient authority and organizational freedom to identify quality problems; to initiate, recommend, or provide solutions; and to verify implementation of solutions. Reporting should be at a management level that is independent of activity performance, costs, and schedule.

Section 2.1.1 of ANSI/ASQC E4-1994 (Ref. 21) and Section 5.2.1 of ANSI N42.23-2003 (Ref. 22)

provide additional guidance on management structure and organizational responsibilities for radiological effluent and environmental monitoring programs.

2. Specification of Qualifications of Personnel The qualifications of individuals needed to carry out assigned radiological monitoring functions should be defined and documented (e.g., as in a job description). Individuals with responsibility for performing quality-related activities should be trained and qualified in the principles and techniques of the activities to be performed. These individuals should maintain proficiency by retraining, reexamining, and recertifying or by periodic performance reviews, as appropriate. Continual training should be conducted as needed to ensure that personnel maintain awareness of events and issues that could affect the quality of program performance.

Section 2.3.1 of ANSI/ASQC E4-1994 (Ref. 21) provides additional guidance and criteria for developing personnel training and qualification specifications for radiological effluent and environmental monitoring programs.

Rev. 2 of RG 4.15, Page 6

3. Operating Procedures and Instructions Monitoring programs should have written procedures for all activities that generate data, such as dose calculations and measurements, sample collection, sample management and CHAIN OF CUSTODY,

sample preparation and analysis, data reduction and recording, data assessment and reporting, and final sample disposal. Procedures are also needed for addressing support functions, such as operation of process monitors, training, preparation of QUALITY CONTROL SAMPLES, collection of meteorological data, corrective actions, AUDITS, and records. Individuals satisfying the qualifications described in Section C.2 of this regulatory guide should write, review, and revise these procedures.

Instructions, procedures, or schedules should be prepared for the functions associated with the QA

program, such as the following:

  • ancillary laboratory functions (including cleaning of glassware, contamination control, and storage of standards and chemicals)
  • CALIBRATION and QC of instrumentation (including range of activity, range of energy, and frequency of calibration)
  • internal QC and external PE programs (including frequency, types, acceptance criteria for the laboratory PERFORMANCE TESTING samples, and individual analyst qualifications)
  • timetable for VERIFICATION and VALIDATION (V&V) of data Chapters 9, 11, and 12 of MARLAP (Ref. 20) provide guidance on the radioanalytical laboratory activities for which procedures are used. MARLAP Chapters 12 - 16 provide technical information that can be used to write or revise procedures. Section 5.4 of ISO/IEC 17025-2005 (Ref. 17) provides additional guidance regarding the content and quality aspects of procedure and method technical content.

Section 2.5.2 of ANSI/ASQC E4-1994 (Ref. 21) identifies procedures that should be documented and may need control.

4. Records licensees should maintain a system that produces unequivocal, accurate records that document all monitoring activities. Licensees should maintain records of implementation or ongoing activities, such as the following:

  • procedure revision
  • personnel training and qualification records
  • analytical results
  • audits
  • corrective actions
  • intermediate activities or calculations (as may be needed to validate or substantiate final results)
  • records of tracking and control (chain of custody) throughout all processes from sample collection through analysis and reporting of results, including unique identifiers, descriptions, sources, dates/times, packaging/preparation/shipping, and required analyses
  • field logs with sufficient information describing environmental conditions and recording related information and data documenting the nature of the sample and where and how it was taken
  • laboratory notebooks recording related information and data, observations of analysts, and laboratory or other conditions potentially affecting the measurement process
  • electronic data collection and algorithms and QA documentation
  • calculations (including data reduction, analysis, and verification)

Rev. 2 of RG 4.15, Page 7

  • QC records for radiation monitoring equipment, including the results of RADIOACTIVE SOURCE

checks, calibrations, INSTRUMEN

T. BACKGROUND

determinations, and maintenance activities affecting equipment performance

  • notifications to qualified staff that procedural changes affecting data quality have been made
  • QC records for laboratory counting systems and support instrumentation and equipment, including calibrations, maintenance or repair, QC sample results, and traceability of standards used for instrument calibration Records should be legible and identifiable, retained in predetermined locations, and protected against damage, deterioration, or loss. Records should be maintained in a format that is easily retrievable.

If the media for storage is electronic (as opposed to paper or microfilm/fiche), the licensee should maintain the equipment necessary to read and present the data in an uncorrupted form. The document retention system should allow reconstruction of all activities associated with the generation of analytical results. The licensee should establish a retention time for records consistent with licensing conditions and in accordance with the licensees overall QA program.

Section 2.5 of ANSI/ASQC E4-1994 (Ref. 21) provides guidance on specific types of documents that should be maintained, while Basic Requirement 17 of ASME NQA-1-1994 (Ref. 11) details the administrative criteria that should be considered for inclusion in a program for records and their retention.

Section 4.13 of ISO/IEC 17025-2005 (Ref. 17) also provides guidance on the control of record

s. Chapters

4 and 11 of MARLAP (Ref. 20) discuss documents that should be retained as records. Nuclear Information and Records Management Association (NIRMA) TG11-1998 (Ref. 23), TG15-1998 (Ref. 24), TG16-1998 (Ref. 25), and TG21-1998 (Ref. 26) provide additional information addressing issues in developing and maintaining electronic records programs.

5. Quality Control in Environmental Sampling Sampling of solids, liquids, and gases involves the measurement of sample masses, flow rates, or volumes. The ACCURACY of the instruments or containers used for this purpose should be determined and checked regularly to ensure that sampling performance criteria remain within the limits specified by the MQOs. The results of mass, flow rate, or volume calibrations and associated UNCERTAINTIES should be recorded. The frequency of these calibrations should be specified and should be consistent with the DQOs of the measurement program. The collection efficiencies of the sampling equipment used should be documented; often such documentation is available from the manufacturer. HPS/ANSI N13.1-1999 (Ref. 27) provides guidance on QA and QC for air sampling instruments. Chapter 19 of MARLAP

(Ref. 20) discusses measurement uncertainties in general and volume and mass measurements in particular.

Sampling or measurements should be performed using equipment and methods that yield a result that is representative of the population in the particular environmental media. FIELD DUPLICATES are co-located spatially or temporally and should be collected periodically to check REPRODUCIBILITY.

Chapter 10 of MARLAP (Ref. 20) discusses the field and sampling issues that affect laboratory measurements, including packaging, shipping, and storage of samples.

Some individual environmental samples are collected simply to confirm that radioactivity levels are below a specified (small) fraction of an established concentration limit. In those cases, the MINIMUM

DETECTABLE CONCENTRATION of the method used should be below that specified fraction of the limit.

Chapter 20 of MARLAP (Ref. 20) discusses detection limits, while Appendix C to MARLAP covers the relationship between the desired fraction of the limit that is important to detect and the uncertainty of the measurement method. In some cases, a series of measurement results will be averaged for comparison with BACKGROUND LEVELS or a regulatory limit. For such measurements, an appropriate MQO would be the MINIMUM QUANTIFIABLE CONCENTRATION (see Chapter 20 of MARLAP).

Rev. 2 of RG 4.15, Page 8

For an isolated, well-mixed population, a single sample or measurement may be sufficient. It is more common, however, for spatial or temporal variations to exist. In that case, the frequency of sampling and number of samples and locations will depend on the level of variability and amount of radioactivity (compared with an established risk-informed limit). NUREG-1575, Multi-Agency Radiation Survey and Site Investigation Manual (Ref. 28, hereafter referred to as MARSSIM), discusses the effect that such variability has on the number of samples that may be appropriate for SURVEYS. In general, the DQO

process may be used together with specific statistical designs (EPA QA/G-9S-2006, Ref. 29) to optimize the sampling. Continuous sampling or integrated measurements may be used to mitigate temporal variability.

Part 1, Sections II-11 and II-12, of ASME NQA-1-1994 (Ref. 11) discuss test control and control of measuring and test equipment. Part II, Subpart 2.20, of ASME NQA-1-1994 discusses QA standards for subsurface investigations for nuclear power plants.

6. Quality Control in the Radioanalytical Laboratory The output of the directed planning process includes DQOs that encompass both sampling and analysis activities for a project or program. From the DQOs, a set of MQOs are developed for radioanalytical measurements (see Chapter 3 of MARLAP, Ref. 20). In a performance-based approach, MQOs are critical criteria used for the selection and validation of analytical methods and protocols (see Regulatory Position 8, below) and subsequently form the basis for the ongoing and final evaluation of the analytical data. The type, frequency of, and evaluation criteria for QC samples are developed during the directed planning process and are incorporated into ANALYTICAL PROTOCOL SPECIFICATIONS (APSs) for a project (see Chapter 3 of MARLAP, Ref. 20).

Chapter 18 of MARLAP provides guidance on monitoring key laboratory PERFORMANCE

INDICATORS to determine whether a laboratorys measurement processes are in control. The chapter also provides information on likely causes of excursions for selected laboratory performance indicators, such as chemical yield, instrument background, and QC samples. Appendix C to MARLAP provides the rationale and guidance for developing MQOs for select method performance characteristics and gives guidance on developing criteria for QC samples.

Performance criteria for radioanalytical measurements should be selected to provide a management tool for tracking and trending performance and to identify precursors to nonconforming conditions.

Laboratories should satisfy program-specific criteria for all measurement processes, including necessary levels of PRECISION, acceptable BIAS, and applicable detection levels.

6.1 Calibration and Quality Control of Instruments, Measuring Devices, and Test Equipment Instruments, devices, and test equipment used for measuring radioactivity should be operated, calibrated, and maintained to ensure that analytical specifications are met. All equipment should be operated, calibrated, and maintained in adherence to any applicable standards and methods and as specified in the laboratorys quality manual and standard operating procedures. Instrument configurations during calibration should match those used for subsequent analytical measurements of samples.

Calibrations of instruments should be made using CERTIFIED REFERENCE MATERIALS of known and documented value and stated uncertainty and should be traceable to a national standards body, such as the National Institute of Standards and Technology (NIST) in the United State

s. CALIBRATION SOURCES

should be prepared in a manner that provides comparability to TEST SOURCES with respect to source geometry, positioning relative to the detector, source composition, and distribution of the test-source material within a container or on a source mount (see Section 15.2 of MARLAP, Ref. 20).

Rev. 2 of RG 4.15, Page 9

The frequency of calibrations should be consistent with the stability and performance of the instrument. Complete system calibration should be performed before initial use or following system maintenance, repair, or any other changes in environment or operating conditions that could affect performance (ASTM D7282-2006, Ref. 30). In addition, Sections 15.2 and 15.3 of MARLAP (Ref. 20)

present general guidance regarding calibrations of instruments. Chapter 15 of MARLAP also presents guidance specific to calibrations of different instrumentation types.

The continuing validity of calibrations should be checked periodically as specified in a laboratorys quality manual (see Chapter 18 of MARLAP, Ref. 20). Quality control checks of radioanalytical instrument calibration parameters, such as detector response or energy and resolution calibrations for spectrometers, should be performed by measuring the response of each radiation detection system to appropriate CHECK SOURCES. Instrument QC frequencies are generally performed daily for systems used continually or before use for those systems periodically employed, but frequencies may vary by instrument type. Instrument QC checks should meet predefined acceptance criteria for the respective calibration parameter and should ensure that conditions have not significantly changed since initial calibration (ASTM

D7282-2006, Ref. 30).

Instrument-calibration QC check results should be tracked, trended, and compared with predetermined ranges of acceptable performance. For example, if a monitors response to a daily check source showed a trend that may lead to a condition outside of established acceptance criteria, a calibration may be needed to reestablish acceptable operation. Section 18.5 of MARLAP (Ref. 20) and ASTM D7282-

2006 (Ref. 30) discuss radioanalytical instrument-calibration QC parameters.

Additional method-specific quality controls (e.g., chemical yield, spectral quality, resolution) may apply to certain methods and should be tracked and trended using control or tolerance charts to identify conditions that could be adverse to quality.

The laboratory quality manual and standard operating procedures should address the use, calibration, maintenance, and QC of all nonradiological instruments, measuring devices, and test equipment used for measuring or quantifying other necessary data (e.g., sample masses or volumes, temperatures). All measurement and test equipment should be calibrated before use and adjusted to maintain accuracy within established limits. Quality control checks should be performed at specified frequencies and should verify that instruments are operating to specified performance levels.

Nonradiological instruments, measurement, and test equipment should be operated according to manufacturers instructions, according to established standards, or as specified in the laboratory quality manual and procedures. Section 18.6.7 of MARLAP (Ref. 20) provides guidance on control, calibration, and maintenance of calibration of apparatus used for mass and volume measurements. ISO/IEC 17025-

2005 (Ref. 17) provides general guidance on establishing quality controls for nonradiological instruments.

Items that do not conform to specified criteria should be controlled to prevent inadvertent use. These items should be tracked through the corrective action program.

Careful control of contamination and routine monitoring of instrument background are integral parts of a measurement QC program. Determination of the background counting rate should be performed on a regular, predefined frequency for systems in routine use and should ensure that analytical specifications for applicable programs can be met. Instrument backgrounds used to determine a net count rate should replicate actual sample measurement conditions as closely as possible (i.e., using appropriate sample containers and geometries).

Rev. 2 of RG 4.15, Page 10

Section 18.5.1 of MARLAP (Ref. 20) provides guidance on measurement and control of instrument backgrounds. Section 18.3 and Attachment 18A of MARLAP contain guidance on the statistical evaluation of performance indicators and on using control and tolerance charts.

Sections 10-13 and 20-25 of ASTM D7282-2006 (Ref. 30) and Section A.5.2 of ANSI N42.23-

2003 (Ref. 22) provide additional guidance on instrument response source checks, background checks, and the use of control charts. ASTM MNL 7A-2002 (Ref. 31) provides guidance on setting up and using control charts.

6.2 Internal Quality Control Samples and Analysis The use of QC samples should be an integral element of a laboratory QA program. Chapter 18 of MARLAP (Ref. 20) defines the different types of laboratory QC samples and provides guidance on evaluation techniques for QC samples. The laboratory should have as part of the normal operational sample load the following QC samples:3

  • BLANK
  • MATRIX SPIKE
  • LABORATORY CONTROL SAMPLE
  • LABORATORY DUPLICATE

Analysis of QC samples should be performed as a part of the routine operation of a laboratory to verify that laboratory operations are consistent with applicable specifications. The QC program should specify the type of and minimum frequency for processing QC samples. For example, this frequency may be defined as a minimum percentage of the total number of samples analyzed, a certain number per operational time interval (e.g., once per shift) or per sample batch, or a licensee-specified frequency based on laboratory-specific parameters. As part of its QC program, the laboratory may prepare and analyze BLIND SAMPLES, provided the individuals responsible for preparing the samples are not directly responsible for conducting the laboratory analysis. For example, the laboratorys assigned QC specialist may have the responsibility for preparing and submitting blind samples (blank, duplicate, laboratory control sample, and matrix spike). Blind samples are used primarily as a tool for evaluating the performance of individuals rather than as part of the laboratory QC load.

Acceptability of QC sample results should be evaluated based on criteria from the QC program, which include specific equations based on METHOD UNCERTAINTY. Chapters 7 and 18 of MARLAP

(Ref. 20) provide guidance on the evaluation of QC samples.

Quality control sample results should be tracked, trended, and compared with predetermined ranges of acceptable performance to identify conditions that are in, or may lead to, nonconformance with program specifications. Such conditions should be tracked through the corrective action program.

6.3 Performance Evaluation Program (Interlaboratory Comparison)

Participation in an external PE program is an important independent check on the accuracy, possible bias, and precision of some radioanalytical or measurement methods used in a radiological monitoring program. Internal and contract radioanalytical laboratories used in the monitoring program should participate in one or more applicable PE programs that are administered by organizations that have an active measurement assurance (traceability) program with NIST (ANSI N42.22-1995, Ref. 32). Chapter

3 Note that this list does not include field duplicate samples that are part of the QC requirement for sampling.

Rev. 2 of RG 4.15, Page 11

5 of MARLAP (Ref. 20) recommends incorporating the criteria for a radioanalytical laboratory to participate in a PE program into the statement of work for services. Several external PE programs administered by government agencies or commercial radioactive-source suppliers are available for radionuclides and matrices germane to radiological monitoring programs. The PE program should provide fundamental sample types (e.g., solid, liquid, gas) and radionuclides (e.g., alpha-, beta-, and gamma- emitting nuclides) of interest at the facility. When available, laboratories should analyze samples as offered by a PE program on a frequency stipulated by the monitoring programs QA criteria, with all types of samples and analyses repeated at least biennially. Chapter 18 of MARLAP (Ref. 20) provides information on organizations that administer PE programs.

Acceptable performance criteria for results of performance-testing samples should be established that are consistent with the MQOs for the radiological monitoring project or program. For certain monitoring activities, the acceptance criteria of the PE program may be satisfactory. The performance in a PE program should be tracked and trended as one of the performance indicators for the laboratory and evaluated as part of the corrective action program.

7. Quality Control for Radioactive Effluent Monitoring Systems

7.1 Radioactive Effluent Process Monitors An initial, primary radiation monitor calibration that meets the specifications of ANSI N42.18-

2004 (Ref. 33), should be performed with radioactive sources traceable to a national standards body (such as NIST). Calibrations should be repeated periodically using (1) STANDARD REFERENCE MATERIALS or (2)

certified reference materials that can be directly traced to the initial, primary calibration. Complete system calibration including electronics, detector, and any support functions (such as alarm, display, and recording devices) should be performed at a frequency that ensures system reliability and accuracy or after repair or maintenance that may affect instrument calibration. Unless otherwise specified in license requirements, the licensee should verify and validate the complete effluent monitoring system every 12 months. This frequency may be extended to longer time periods coinciding with facility maintenance schedules, such as refueling for nuclear power plants, if the licensee has verified proper system operation through established system reliability and more frequent source checks and functional checks.

Detectors should be response-checked periodically4 for continuous effluent release points (e.g., ventilation systems and secondary water systems) and before release for batch discharges (e.g., primary boundary or containment purges and liquid waste tank releases). Licensees should ensure that check sources are of sufficient radiochemical purity so that the activity of the source may be corrected for decay to the date of measurement. These check sources need not be traceable to a national standards body (e.g., NIST). Whenever practicable, check sources should be an integral part of the monitoring system and should be remotely actuated. The functionality of isolation or alarm functions should be verified periodically, preferably by use of a radiation source.

Trends of process radiation monitor readings versus total radionuclide concentrations in the monitored release path should be performed routinely. These trends should be based on the results of analyses for specific radionuclides in samples taken from the release path that will yield a monitor response. Deviations in the trend may occur if concentrations or the mixture of radionuclides changed significantly (for example, during a fuel cycle in which significant fuel defects exist). The licensee should define the monitor-response parameter for all radiation monitors. The monitor-response constant should be adjusted to maintain this correlation between effluent radionuclide concentration and monitor response.

4 Frequencies should be appropriate to the instrument under consideration and may be dictated by license conditions.

Rev. 2 of RG 4.15, Page 12

7.2 Flow Monitoring Instrumentation Continuous sampling of liquids and gases involves the measurement of sample flow rates and/or sample volumes. The accuracy and associated uncertainty of the devices used for this purpose should be determined on a regularly scheduled basis, and adjustments should be made as needed to bring the performance of the devices within specified limits. The results of these calibrations should be recorded.

The frequency of these calibrations should be specified and should be based on the necessary accuracy, purpose, degree of usage, stability characteristics, and other conditions affecting the measurement.

Any flow-rate measuring devices associated with the system should be calibrated to determine actual flow rates at the conditions of temperature and pressure under which the system will operate. These flow rate devices should be recalibrated annually, but the frequency may be extended to that established for the radiation detector system, provided sufficient operating experience exists and an accelerated measurement check frequency gives sufficient data to ensure reliable performance.

Flow measuring devices should be checked periodically on an established frequency, considering the variability of the instrument, and recalibrated when established control limits are exceeded. HPS/ANSI

N13.1-1999 (Ref. 27) provides additional guidance on QA and QC measures for the use, maintenance, and calibration of airborne sampling instrumentation. ANSI N42.18-2004 (Ref. 33) provides additional guidance on the calibration of liquid flow monitors.

7.3 Grab Sampling of Effluent Process Streams Whenever practicable, effluent releases should be batch-controlled and released when the volume to be released has been mixed sufficiently to ensure uniform concentration. Sampling and analysis for each batch should be performed, and release conditions set, before release. A certain percentage of all batch releases should have field duplicates taken either before or during the release to assess the reproducibility of sampling and the effectiveness of the mixing process before release. Where possible, samples that are spatially or temporally separated should be collected periodically to verify representativeness.

For continuous-effluent discharges, composite samplers should be employed. However, periodic grab samples may be used when composite sampling of a continuous discharge point is not feasible. When grab samples are collected instead of composite samples, licensees should design the sampling program to sample at the time, location, and frequency that ensures each sample is representative of the radioactive materials released.

7.4 General Quality Control Considerations The QC plan should address the following items:

  • Sampling should be performed using calibrated instruments and equipment when taking a composite sample.
  • Collection efficiencies based on the physical configuration of the sampling point and the type of collector should be documented. Vendor-supplied data may be used where adequate documentation exists to ensure the reliability and accuracy of data.
  • Volumes of tanks and containers should be established during initial installation and should be verified again following any physical changes that could alter the system configuration.

Rev. 2 of RG 4.15, Page 13

  • The frequency of duplicates and REPLICATES5 should be established based on time (for continuous discharges) or number of batches (for batch discharges).
  • Sample integrity should be maintained through chain of custody procedures.

Procedures for continuous sampling should use methods that are designed to ensure that the sample is representative of the volumes being discharged.

8. Verification and Validation The V&V of certain aspects and support activities of the radiological measurement process or monitoring program are essential to the QA program. These aspects and activities include data and computer software V&V and project method validation.

Project method validation is the demonstration that a method (radioanalytical or radiation measurement) using performance-based method selection is capable of providing analytical results to meet a projects MQOs and any other criteria in the analytical protocol specification (APS). Acceptable method validation is necessary before the radiological analysis of samples or the taking of measurements in a monitoring program. Chapter 6 of MARLAP (Ref. 20) presents detailed guidance on project method validation for radioanalytical methods. In addition, Section 5.2.7 of ANSI N42.23-2003 (Ref. 22) and Section 5.4.5 of ISO/IEC 17025-2005 (Ref. 17) provide limited guidance for radioanalytical method validation.

Chapter 8 of MARLAP (Ref. 20) gives detailed guidance and applicable tools for the radioanalytical data V&V evaluation process as well as information for developing a data V&V plan, determining acceptable criteria and tests, and applying data qualifiers for radioanalytical data validation, as related to MQOs. EPA QA/G-8-2002 (Ref. 34) provides guidance for nonradioanalytical data V&V.

Computer programs used in the implementation of the radiological environmental monitoring program should be documented, verified, and validated before initial routine use and after each modification of the program. As described in Section 5.4.3.2 of MARLAP (Ref. 20), the laboratorys quality manual should include the criteria for computer software V&V and documentation. The software data reduction and reporting functions should be verified to perform as expected.6

9. Assessments and Audits Assessments, audits, and surveillances are elements used to evaluate the initial and ongoing effectiveness of the QA program to monitor and control the quality of a radiological monitoring program.

Management having responsibility in the area being reviewed should document and review the results of these activities. Assessments that are independent of the day-to-day operations should be performed routinely, including management surveillance, peer reviews, and READINESS REVIEWS for new or revised systems and methods. Key performance indicators should be tracked and trended, with periodic management reporting. The QA program or project plan should outline the scope, frequency, and schedule of assessments, audits, and surveillances. A plan should be developed for each assessment audit or

5 Replicate samples may be prepared by removing separate ALIQUANTS from the same grab sample.

6 The Institute of Electrical and Electronics Engineers (IEEE) Standard 1063, IEEE Standard for Software User Documentation (Ref. 35); EPA Directive 2185, Good Automated Laboratory Practices (Ref. 36); Subpart 2.7 of ASME NQA-1-1994 (Ref. 11); Regulatory Guide 1.168, Verification, Validation, Reviews, and Audits for Digital Computer Software Used Safety Systems of Nuclear Power Plants (Ref. 37); and Section 8 of ANSI N42.14-1999, Calibration and Use of Germanium Spectrometers for the Measurement of Gamma-Ray Emission Rates of Radionuclides (Ref. 38), also provide guidelines on software V&V.

Rev. 2 of RG 4.15, Page 14

surveillance for each area of the monitoring program being evaluated. A report of these activities should be generated according to the outline, format, and content established in the plan.

Only qualified QA staff (see Regulatory Position 2, above), supported as needed by experts in the technical areas under evaluation, should conduct assessments, audits, and surveillances. (See ASME

NQA-1-1994, Supplement 2S, Ref. 11.) Deficiencies, areas for improvement, and observations noted should be incorporated into the corrective action program and tracked. Section 18 of ASME NQA-1-1994 (Ref. 11) and Section 4.10 of ISO/IEC 17025-2005 (Ref. 17) provide guidance on establishing and conducting an audit program.

When the monitoring program will depend upon the services of a radioanalytical laboratory, prior onsite audits of the laboratory may be conducted to ensure that the laboratory is capable of fulfilling the project criteria in accordance with the APS (including MQOs) outlined in a statement of work (MARLAP

Chapter 5 and Appendix E). The ongoing evaluation of the laboratorys QUALITY SYSTEM and operations is accomplished through onsite audits and desk audits. These audits are focused more on whether the laboratory is meeting project or program specifications than whether the laboratory has the capability to meet monitoring program or project criteria. Chapter 7 of MARLAP provides guidance and statistical tests to determine whether a laboratory is meeting the MQOs, especially the REQUIRED METHOD UNCERTAINTY.

Section 5.2.10 of ANSI N42.23-2003 provides additional guidance for radioanalytical laboratory assessments.

Audits of the QA programs of contractors providing materials, supplies, or services affecting the quality of the laboratorys operations should be performed periodically (Section 4.6 of ISO/IEC 17025-

2005, Ref. 17).

10. Preventive and Corrective Actions Integral components of a QA program include identifying areas for improvement, defining performance or programmatic deficiencies, and initiating appropriate corrective or preventive actions. The QA program for radiological effluent and environmental monitoring programs should contain both a continuous-improvement program and a program for implementing corrective actions when conditions adverse to quality have been identified. In addition, needed improvements and potential sources of nonconformance should be identified and reported as part of a preventive action initiative of the continuous-improvement program (ISO/IEC 17025-2005, Sections 4.10-4.12) for example, a condition- reporting program. Investigations should be initiated for degrading conditions, and corrective actions should be taken when conditions fall outside quality or regulatory acceptance criteria. For conditions that are adverse to quality, the corrective action process includes the following basic elements:

  • identification and documentation
  • classification
  • cause analysis
  • corrections
  • followup
  • closure Findings and corrective actions should be documented, tracked, and reported to management.

Followup reviews should be performed to verify the effectiveness and adequacy of the corrective actions.

Section 2.10 of ANSI/ASQC E4-1994 (Ref. 21) provides specifications and guidelines for developing the process, programs, and procedures necessary to detect and correct items of nonconformance and for implementing continuous quality improvement.

Rev. 2 of RG 4.15, Page 15

When conducting an audit or surveillance of laboratory services, a prime area of review should be the effectiveness of the laboratorys corrective action program (Section 7.4.2 of MARLAP, Ref. 20).

Section 4.11 of ISO/IEC 17025-2005 (Ref. 17) provides general guidance on preventive and corrective action programs for laboratories. Annex C of ANSI N42.23-2003 (Ref. 22) provides additional guidance that should be considered in developing a corrective action program, including root cause analysis for radioanalytical services.

D. IMPLEMENTATION

The purpose of this section is to provide information to licensees regarding the NRC staffs plans for using this regulatory guide. No backfit is intended or approved in connection with its issuance.

Non-nuclear power reactor applicants and licensees may continue to use Revision 1 of Regulatory Guide 4.15, dated February 1979, or may adopt other procedures or practices that reflect generally accepted standards for ensuring quality in environmental data collected for effluent monitoring purposes. Except in those cases in which a nuclear power reactor applicant or licensee proposes or has previously established an acceptable alternative method for complying with specified portions of the NRCs regulations, the methods and practices described in this guide will be used in evaluating QA practices for environmental radiological monitoring programs.

Rev. 2 of RG 4.15, Page 16

GLOSSARY7 accuracyThe closeness of a measured result to the true value of the quantity being measured.

Various recognized authorities have given the word accuracy different technical definitions, expressed in terms of bias and imprecision. Following the Multi-Agency Radiological Laboratory Analytical Protocols (MARLAP) Manual (Ref. 20), the U.S. Nuclear Regulatory Commission (NRC) avoids all of these technical definitions and uses the term accuracy in its common, ordinary sense, which is consistent with the definition established by the International Organization for Standardization (ISO) in the International Vocabulary of Basic and General Terms in Metrology (Ref. 39).

aliquantA representative portion of a homogeneous SAMPLE removed for the purpose of analysis or other chemical treatment. The quantity removed is not an evenly divisible part of the whole sample. An aliquot, by contrast, is an evenly divisible part of the whole.

analyteSee TARGET ANALYTE.

analytical protocol specification (APS)The output of a DIRECTED PLANNING PROCESS that contains the projects analytical data needs and criteria in an organized, concise form. The level of specificity in the APS should be limited to those criteria that are considered essential to meeting the projects analytical data criteria to allow the laboratory the flexibility of selecting the protocols or methods that meet the analytical criteria.

as low as reasonably achievable (ALARA)As low as is reasonably achievable taking into account the state of the technology and the economics of improvements in relation to benefits to the public health and safety and other societal and socioeconomic considerations, and in relation to the use of atomic energy in the public interest [10 CFR 50.34a(a)].

assessmentA planned and documented activity performed to determine whether various elements within a quality management system are effective in achieving stated quality objectives (ANSI N42.23-

2003, Ref. 22).

auditA planned and documented activity performed to determine by investigation, examination, or evaluation of objective evidence the adequacy of, and CONFORMANCE with, established procedures, instructions, drawings, and other applicable documents as well as the effectiveness of implementation. An audit should not be confused with surveillance or inspection activities performed for the sole purpose of process control or product acceptance (after ANSI N42.23-2003, Ref. 22).

background, instrumentRadiation detected by an instrument when no SOURCE is present. The background radiation that is detected may come from radionuclides in the materials of construction of the detector, its housing, its electronics, and the building as well as the environment and natural radiation.

background levelA term that usually refers to the presence of radioactivity or radiation in the environment. From an analytical perspective, the presence of background radioactivity in samples

7 Certain terms included in this glossary are not used in the main body of this regulatory guide, but are included because they are used within other definitions.

Rev. 2 of RG 4.15, Page 17

needs to be considered when clarifying the radioanalytical aspects of the decision or study question. Many radionuclides are present in measurable quantities in the environment.

bias (of a measurement process)A persistent deviation of the mean measured result from the true or accepted reference value of the quantity being measured, which does not vary if a measurement is repeated.

blank (analytical or method)A SAMPLE that is assumed to be essentially free of the TARGET ANALYTE

(the unknown), that is carried through the radiochemical preparation, analysis, mounting, and measurement process in the same manner as a routine sample of a given matrix.

blind sampleA SAMPLE with a concentration not known to the analyst. Blind samples are used to assess analytical performance. A double-blind sample is a sample whose concentration and identity as a sample is known to the submitter, but not to the analyst. The analyst should treat the double-blind sample as a routine sample, so it is important that the double-blind sample is identical in appearance to routine samples.

calibrationThe set of operations that establish, under specified conditions, the relationship between values indicated by a measuring instrument or measuring system, or values represented by a material measure, and the corresponding known value of a parameter of interest.

calibration sourceA prepared SOURCE, made from a CERTIFIED REFERENCE MATERIAL OR STANDARD

REFERENCE MATERIAL, that is used for calibrating instruments.

certified reference materialA reference material, accompanied by a certificate, with one or more property values certified by a procedure that establishes its traceability to an accurate realization of the unit in which the property values are expressed, and for which each certified value is accompanied by an UNCERTAINTY at a stated level of confidence (ISO Guide 30, Ref. 40). See STANDARD REFERENCE MATERIAL.

chain of custodyProcedures that provide the means to trace the possession and handling of a sample from collection to data reporting.

check sourceA material used to validate the operability of a radiation measurement device, sometimes used for instrument quality control. See TEST SOURCE and SOURCE, RADIOACTIVE.

condition adverse to quality an all-inclusive term used in reference to any of the following: failures, malfunctions, deficiencies, defective items, and nonconformances. A significant condition adverse to quality is one which, if uncorrected, could have a serious effect on safety or operability.

conformanceAn affirmative indication or judgment that a product or service has met the criteria of the relevant specifications, contract, or regulation; also the state of meeting the criteria (ANSI/ASQC

E4-1994, Ref. 21).

corrective actionsThose measures taken to prevent, rectify, or eliminate conditions adverse to quality or detected nonconformities and as necessary to preclude repetition of those conditions.

data quality objective (DQO)Qualitative and quantitative statements that clarify the study objectives, define the most appropriate type of data to collect, determine the most appropriate conditions from which to collect the data, and specify tolerable limits on decision error rates. Because DQOs will be used to establish the quality and quantity of data needed to support decisions, they should Rev. 2 of RG 4.15, Page 18

encompass the total UNCERTAINTY resulting from all data collection activities, including analytical and sampling activities.

directed planning processA systematic framework focused on defining the data needed to support an informed decision for a specific project. Directed planning provides a logic for setting well- defined, achievable objectives and developing a cost-effective, technically sound sampling and analysis design that balances the data users tolerance for UNCERTAINTY in the decision process and the available resources for obtaining data to support a decision. Directed planning helps to eliminate unnecessary, poor, or inadequate sampling and analysis designs.

dose equivalentQuantity that expresses all radiations on a common scale for calculating the effective absorbed dose. This quantity is the product of absorbed dose (GRAYS (Gy) or rads) multiplied by a quality factor and any other modifying factors (MARSSIM, Ref. 28). The quality factor adjusts the absorbed dose because not all types of ionizing radiation create the same effect on human tissue.

For example, a dose equivalent of one SIEVERT (Sv) requires 1 Gy of beta or gamma radiation, but only 0.05 Gy of alpha radiation or 0.1 Gy of neutron radiation. Because the sievert is a large unit, radiation doses often are expressed in milliSIEVERTS (mSv). See TOTAL EFFECTIVE DOSE

EQUIVALENT.

duplicate, fieldTwo samples of the same material, collected at the same location at the same time and under the same conditions, which are used to verify representativeness of the sampled material.

duplicate, laboratoryTwo ALIQUANTS of a SAMPLE, which are prepared and analyzed separately as part of the same batch, used in the laboratory to measure the overall PRECISION of the sample measurement process, beginning with laboratory subsampling of a field SAMPLE.

field duplicateSee DUPLICATE, FIELD.

graded approachA process of basing the level of management controls applied to an item or work on the intended use of the results and the degree of confidence needed in the quality of the results.

The NRC follows a graded approach to project planning and QUALITY ASSURANCE because of the diversity of environmental data collection activities. This diversity in the type of project and the data to be collected impacts the content and extent of the detail to be presented in the project planning documents.

gray (Gy)The International System of Units (SI) unit for absorbed radiation dose. One Gy is 1 joule of energy absorbed per kilogram of matter, equal to 100 RAD. See SIEVERT.

laboratory control sampleA standard material of known composition or an artificial SAMPLE (created by fortification of a clean material similar in nature to the sample), which is prepared and analyzed in the same manner as the sample. In an ideal situation, the result of an analysis of the laboratory control sample should be equivalent to (give 100 percent of) the TARGET ANALYTE concentration or activity known to be present in the fortified sample or standard material. The result normally is expressed as percent recovery. See also QUALITY CONTROL SAMPLE.

laboratory duplicateSee DUPLICATE, LABORATORY.

matrix spikeSee SPIKE.

Rev. 2 of RG 4.15, Page 19

measurement quality objective (MQO)The analytical data criteria of the DATA QUALITY OBJECTIVES,

which are project- or program-specific and can be quantitative or qualitative. These analytical data criteria serve as measurement performance criteria or objectives of the analytical process.

MARLAP (Ref. 20) refers to these performance objectives as MQOs. Examples of quantitative MQOs include statements of required analyte detectability and the UNCERTAINTY of the analytical protocol at a specified radionuclide concentration, such as the action level. Examples of qualitative MQOs include statements of the required specificity of the analytical protocol (e.g., the ability to analyze for the radionuclide of interest (or TARGET ANALYTE) given the presence of interferences).

method uncertaintyReference to the predicted UNCERTAINTY of the result that would be measured if the method were applied to a hypothetical laboratory SAMPLE with a specified analyte concentration.

Although individual measurement uncertainties will vary from one measured result to another, the REQUIRED METHOD UNCERTAINTY is a target value for the individual measurement uncertainties and is an estimate of uncertainty before the sample is actually measured. See also UNCERTAINTY and REQUIRED METHOD UNCERTAINTY.

method validationThe demonstration that the method selected for the analysis of a particular analyte in a given matrix is capable of providing analytical results to meet the projects MEASUREMENT

QUALITY OBJECTIVES and any other criteria in the ANALYTICAL PROTOCOL SPECIFICATIONS.

Compare with data and software VALIDATION.

minimum detectable concentrationThe minimum detectable value of the analyte concentration in a sample. The smallest (true) value of the net state variable that gives a specified probability that the value of the response variable will exceed its critical value (i.e., that the material analyzed is not blank).

minimum quantifiable concentrationMinimum quantifiable value of the analyte concentration, defined as the smallest concentration of analyte whose presence in a laboratory SAMPLE ensures that the relative standard deviation of the measurement does not exceed a specified value, usually 10

percent.

nonconformancea deficiency in characteristic, documentation, or procedure that renders the quality of an item or activity unacceptable or indeterminate performance-based approachDefinition of the analytical data needs and criteria of a project in terms of measurable goals during the planning phase of a project. In a performance-based approach, the project-specific data objectives that are determined during a DIRECTED PLANNING PROCESS serve as measurement performance criteria for selections and decisions regarding the conduct of the laboratory analyses. The project-specific analytical data objectives are also used for the initial, ongoing, and final evaluation of the laboratorys performance and the laboratory data. In method selection, a performance-based approach is the process wherein a validated method is selected based on a demonstrated capability to meet defined quality and laboratory performance criteria.

performance evaluation (PE) programA laboratorys participation in an internal or external program of analyzing performance-testing samples appropriate for the analytes and matrices under consideration (i.e., PE program traceable to a national standards body, such as the National Institute of Standards and Technology (NIST) in the United States). Reference-material samples used to evaluate the performance of the laboratory are called performance-evaluation or performance-testing samples or materials. See CERTIFIED REFERENCE MATERIAL and STANDARD

REFERENCE MATERIAL.

Rev. 2 of RG 4.15, Page 20

performance indicatorInstrument- or protocol-related parameter routinely monitored to assess the laboratorys estimate of controls such as chemical yield, instrument background, UNCERTAINTY,

PRECISION, and BIAS. See BACKGROUND, INSTRUMENT.

performance testingSee PERFORMANCE EVALUATION PROGRAM.

precisionThe closeness of agreement between independent test results obtained by applying the experimental procedure under stipulated conditions. Conversely, imprecision is the variation of the results in a set of REPLICATE measurements. Precision may be expressed as the standard deviation (IUPAC, Ref. 41).

quality assurance (QA)An integrated system of management activities involving planning, implementation, assessment, reporting, and quality improvement to ensure that a process, item, or service is of the type and quality needed and expected. Quality assurance includes QUALITY

CONTROL.

quality assurance project plan (QAPP)A formal document describing in detail the necessary QUALITY

ASSURANCE, QUALITY CONTROL, and other technical activities that must be implemented to ensure that the results of the work performed will satisfy the stated performance criteria. The QA project plan describes policy, organization, and functional activities and the DATA QUALITY OBJECTIVES

and measures necessary to achieve adequate data for use in selecting the appropriate remedy.

quality control (QC)The overall system of technical activities that measures the attributes and performance of a process, item, or service against defined standards to verify that they meet the stated objectives established by the project; operational techniques and activities that are used to fulfill objectives for quality. This system of activities and checks is used to ensure that measurement systems are maintained within prescribed limits, providing protection against out-of- control conditions and ensuring that the results are of acceptable quality.

quality control (QC) sampleAn uncontaminated SAMPLE matrix spiked with known amounts of analytes from a source independent of the calibration standards.

quality systemA structured and documented management system describing the policies, objectives, principles, organizational authority, responsibilities, accountability, and implementation plan of an organization for ensuring quality in its work processes, products (items), and services. The quality system provides the framework for planning, implementing, and assessing the work performed by an organization and for carrying out required QUALITY ASSURANCE and QUALITY CONTROL

activities (ANSI/ASQC E4-1994, Ref. 21).

readiness reviewThe formal process of performing a written or verbal assessment of key attributes of a program or project measured against defined minimum criteria, standards, or quality metrics before initiation of activities under that project or program.

recordA retrievable document that furnishes objective evidence of the quality of products, services, or activities and that has been verified and authenticated as technically complete and correct.

remThe common unit for the effective or equivalent dose of radiation received by a living organism, equal to the actual dose (in rads) multiplied by a factor representing the danger of the radiation.

Rem is an abbreviation for roentgen equivalent man, meaning that it measures the biological effects of ionizing radiation in humans. One rem is equal to 0.01 Sv. See SIEVERT and DOSE EQUIVALENT.

Rev. 2 of RG 4.15, Page 21

replicatesTwo or more ALIQUANTS of a homogenous SAMPLE whose independent measurements are used to determine the PRECISION of laboratory preparation and analytical procedures.

reproducibilityThe closeness of the agreement between the results of measurements of the same parameter carried out under changed conditions of measurement. A valid statement of reproducibility depends upon specification of the conditions changed. The changed conditions may include principle of measurement, method of measurement, observer (or analyst), measuring instrument, reference standard, location, conditions of use, and time. Reproducibility may be expressed quantitatively in terms of the dispersion characteristics of the results. Results are usually understood to be corrected results.

required method uncertainty (uMR)METHOD UNCERTAINTY at a specified concentration. This is a key MEASUREMENT QUALITY OBJECTIVE.

sample(1) A portion of material selected from a larger quantity of material, or (2) a set of individual samples or measurements drawn from a population whose properties are studied to gain information about the entire population.

sievert (Sv)The Systme International (SI) unit for the effective dose of radiation received by a living organism. This unit represents the actual dose received (GRAYS in SI or rads in traditional units)

times a factor that is larger for more dangerous forms of radiation. One Sv is 100 REM. Radiation doses are often measured in mSv. An effective dose of 1 Sv requires 1 GRAY of beta or gamma radiation, but only 0.05 Gy of alpha radiation or 0.1 Gy of neutron radiation.

source, radioactiveA quantity of material configured for radiation measurement.

spikeA known amount of TARGET ANALYTE added to the environmental sample to establish whether the method or procedure is appropriate for the analysis of the particular matrix and how the TARGET

ANALYTE responds when the environmental sample is prepared and measured, thereby estimating the bias introduced by the sample matrix. Also termed MATRIX SPIKE.

standard reference materialA CERTIFIED REFERENCE MATERIAL issued by NIST in the United States.

NIST certifies a standard reference material for specific chemical or physical properties and issues it with a certificate that reports the results of the characterization and indicates the intended use of the material.

surveillanceContinual or frequent monitoring and verification of the status of an activity and the analysis of records to ensure that specified requirements are being fulfilled. A surveillance is less extensive and more frequent than an AUDIT and concentrates on a single item or activity.

surveyA systematic evaluation and documentation of radiological measurements with a correctly calibrated instrument or instruments that meet the sensitivity required by the objective of the evaluation.

target analyteA radionuclide on the list of radionuclides of interest or a radionuclide of concern for a project.

test sourceThe final radioanalytical processing product or matrix (e.g., precipitate, solution, filter) that is introduced into a measurement instrument. A test source is prepared from laboratory sample material for the purpose of determining its radioactive constituents. See CALIBRATION SOURCE,

CHECK SOURCE, and SOURCE, RADIOACTIVE.

Rev. 2 of RG 4.15, Page 22

total effective dose equivalent (TEDE)The sum of the effective dose equivalent (for external exposure)

and the committed effective dose equivalent (for internal exposure), expressed in units of Sv or rem (MARSSIM, Ref. 28). See DOSE EQUIVALENT.

uncertaintyA parameter, usually associated with the result of a measurement, that characterizes the dispersion of the values that could reasonably be attributed to the measurement of interest (Chapter 19 of MARLAP, Ref. 20).

validation(1) Data validation, the evaluation of data to determine the presence or absence of an analyte and to establish the UNCERTAINTY of the measurement process for contaminants of concern. Data validation qualifies the usability of each datum (after interpreting the impacts of exceptions identified during data VERIFICATION) by comparing the data produced with the MEASUREMENT

QUALITY OBJECTIVES and any other analytical process criteria contained in the ANALYTICAL

PROTOCOL SPECIFICATIONS developed in the planning process. (2) Software validation, the confirmation by examination and provision of objective evidence that the particular criteria for a specific intended use are fulfilled. Validation for a system is the set of activities ensuring and gaining confidence that the system is able to accomplish its intended use, goals, and objectives (ISO/IEC 15288-2002, Ref. 42).

verification(1) Data verification, a process that ensures that laboratory conditions and operations were compliant with the statement of work, sampling and analysis plan, and QUALITY ASSURANCE

PROJECT PLAN and that identifies problems, if present, that should be investigated during data validation. Data verification compares the material delivered by the laboratory to these criteria (compliance) and checks for consistency and comparability of the data throughout the data package and for completeness of the results to ensure that all necessary documentation is available. (2)

Software verification, the confirmation by examination and provision of objective evidence that specified criteria have been fulfilled. A set of activities compares a system life cycle product against the necessary characteristics for that product. The system life cycle products may include, but are not limited to, specified criteria, design description, and the system itself (ISO/IEC 15288-

2002, Ref. 42).

Rev. 2 of RG 4.15, Page 23

REFERENCES

1. 10 CFR Part 50, Domestic Licensing of Production and Utilization Facilities, U.S. Nuclear Regulatory Commission, Washington, DC.8

2. 10 CFR Part 52, Licenses, Certifications, and Approvals for Nuclear Power Plants, U.S. Nuclear Regulatory Commission, Washington, DC.8

3. 10 CFR Part 61, Licensing Requirements for Land Disposal of Radioactive Waste, U.S. Nuclear Regulatory Commission, Washington, DC.8

4. 10 CFR Part 72, Licensing Requirements for the Independent Storage of Spent Nuclear Fuel, High-Level Radioactive Waste, and Reactor-Related Greater Than Class C Waste, U.S. Nuclear Regulatory Commission, Washington, DC.8

5. 10 CFR Part 76, Certification of Gaseous Diffusion Plants, U.S. Nuclear Regulatory Commission, Washington, DC.8

6. 10 CFR Part 30, Rules of General Applicability to Domestic Licensing of Byproduct Material, U.S. Nuclear Regulatory Commission, Washington, DC.8

7. 10 CFR Part 40, Domestic Licensing of Source Material, U.S. Nuclear Regulatory Commission, Washington, DC.8

8. 10 CFR Part 70, Domestic Licensing of Special Nuclear Material, U.S. Nuclear Regulatory Commission, Washington, DC.8

9. 10 CFR Part 20, Standards for Protection Against Radiation, U.S. Nuclear Regulatory Commission, Washington, DC.8

10. 40 CFR Part 190, Environmental Radiation Protection Standards for Nuclear Power Operations, U.S. Environmental Protection Agency, Washington, DC.9

11. ASME NQA-1-1994, Quality Assurance Program Requirements for Nuclear Facilities (with Addenda), American Society of Mechanical Engineers, New York, NY, 1994.10

8 All NRC regulations listed herein are available electronically through the Public Electronic Reading Room on the NRCs public Web site, at http://www.nrc.gov/reading-rm/doc-collections/cfr/. Copies are also available for inspection or copying for a fee from the NRCs Public Document Room at 11555 Rockville Pike, Rockville, MD;

the PDRs mailing address is USNRC PDR, Washington, DC 20555; telephone (301) 415-4737 or (800) 397-4209;

fax (301) 415-3548; email PDR@nrc.gov.

9 This regulation is available electronically through the U.S. Environmental Protection Agencys public Web site, at http://www.epa.gov/epacfr40/chapt-I.info/.

10

Purchase information is available through the American Society of Mechanical Engineers (ASME) Web site at http://catalog.asme.org/Codes/PrintBook/NQA1_1994_Quality_Assurance.cfm.

Rev. 2 of RG 4.15, Page 24

12. Generic Letter 79065, Radiological Assessment Branch Technical Position on Radiological Environmental Monitoring, Revision 1, U.S. Nuclear Regulatory Commission, Washington, DC,

November 27, 1979.11

13. Regulatory Guide 1.21, Measuring, Evaluating, and Reporting Radioactivity in Solid Wastes and Releases of Radioactive Materials in Liquid and Gaseous Effluents from Light-Water-Cooled Nuclear Power Plants, U.S. Nuclear Regulatory Commission, Washington, DC.12

14. Regulatory Guide 4.1, Programs for Monitoring Radioactivity in the Environs of Nuclear Power Plants, U.S. Nuclear Regulatory Commission, Washington, DC.12

15. Regulatory Guide 4.14, Radiological Effluent and Environmental Monitoring at Uranium Mills, U.S. Nuclear Regulatory Commission, Washington, DC.12

16. Regulatory Guide 4.16, Monitoring and Reporting Radioactivity in Releases of Radioactive Materials in Liquid and Gaseous Effluents from Nuclear Fuel Processing and Fabrication Plants and Uranium Hexafluoride Production Plants, U.S. Nuclear Regulatory Commission, Washington, DC.12

17. ISO/IEC 17025-2005, General Requirements for the Competence of Testing and Calibration Laboratories, International Standards Organization/International Electrotechnical Commission, Geneva, Switzerland, May 2005, Correction 1, August 2006.13

18. EPA QA/G-4-2006, Guidance on Systematic Planning Using the Data Quality Objectives Process, U.S. Environmental Protection Agency, Washington, DC, EPA 240/B-06/001, February 2006.14

19. EPA QA/G-5-2002, Guidance for Quality Assurance Project Plans, U.S. Environmental Protection Agency, Washington, DC, EPA/240/R-02/009, December 2002.14

20. NUREG-1576 (MARLAP), Multi-Agency Radiological Laboratory Analytical Protocols Manual, Volumes 1-3, U.S. Nuclear Regulatory Commission, Environmental Protection Agency, Department of Energy, Department of Defense, Department of Homeland Security, National

11 Generic Letter 79065 is available electronically through the NRCs public Web site at http://www.nrc.gov/reading-rm/

doc-collections/gen-comm/gen-letters/1979/gl79065.html.

12 All regulatory guides listed herein were published by the U.S. Nuclear Regulatory Commission or its predecessor, the U.S. Atomic Energy Commission. Most are available electronically through the Electronic Reading Room on the NRCs public Web site, at http://www.nrc.gov/reading-rm/doc-collections/reg-guides/. Active guides may be purchased from the National Technical Information Service (NTIS). Details may be obtained by contacting NTIS at

5285 Port Royal Road, Springfield, Virginia 22161, online at http://www.ntis.gov, by telephone at (800) 553-NTIS

(6847) or (703) 605-6000, or by fax to (703) 605-6900. Copies are also available for inspection or copying for a fee from the NRCs Public Document Room (PDR), which is located at 11555 Rockville Pike, Rockville, Maryland; the PDRs mailing address is USNRC PDR, Washington, DC 20555-0001. The PDR can also be reached by telephone at

(301) 415-4737 or (800) 397-4209, by fax at (301) 415-3548, and by email to PDR@nrc.gov.

13 Copies of all ISO publications cited in this document may be purchased from ISO in Geneva, Switzerland.

Purchase information is available through the ISO Web site at http://www.iso.org/iso/en/ISOOnline.frontpage.

14 Copies of all EPA quality system publications are available for download free of charge from the EPA public Web site at http://www.epa.gov/quality/qa_docs.html.

Rev. 2 of RG 4.15, Page 25

Institute of Standards and Technology, U.S. Geological Survey, and Food and Drug Administration, Washington, DC, July 2004.15

21. ANSI/ASQC E4-1994, Specifications and Guidelines for Quality Systems for Environmental Data Collection and Environmental Technology Programs, American National Standards Institute/American Society for Quality Control, New York, NY, 1994.16

22. ANSI N42.23-2003, Measurement and Associated Instrumentation Quality Assurance for Radioassay Laboratories, American National Standards Institute, New York, NY, 2003.16

23. NIRMA TG11, Authentication of Records and Media, Nuclear Information and Records Management Association, Inc., Windham, NH, 1998.17

24. NIRMA TG15, Management of Electronic Records, Nuclear Information and Records Management Association, Inc., Windham, NH, 1998.17

25. NIRMA TG16, Software Configuration Management and Quality Assurance, Nuclear Information and Records Management Association, Inc., Windham, NH, 1998.17

26. NIRMA TG21, Electronic Records Protection and Restoration, Nuclear Information and Records Management Association, Inc., Windham, NH, 1998.17

27. HPS/ANSI N13.1-1999, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stacks and Ducts of Nuclear Facilities, Health Physics Society (HPS), McLean, VA,

1999.18

28. NUREG-1575 (MARSSIM), Multi-Agency Radiation Survey and Site Investigation Manual, Revision 1 (EPA 402-R-97-016 Revision 1, DOE/EH-0624 Revision 1), U.S. Nuclear Regulatory Commission, Environmental Protection Agency, Department of Energy, Washington, DC,

August 2000.15

29. EPA QA/G-9S-2006, Data Quality Assessment: Statistical Tools for Practitioners, U.S.

Environmental Protection Agency, Washington, DC, EPA/240/B-06/003, February 2006.14

15 Copies are available electronically through NRCs public Web site at http://www.nrc.gov/reading-rm/doc-collections/

nuregs/staff/sr1576/ and from EPAs public Web site at http://www.epa.gov/radiation/marlap/links.htm.

16 Copies of all ANSI publications cited in this document may be purchased from the American National Standards Institute, 1819 L Street, NW, 6th floor, Washington, DC 20036. Purchase information is available through the ANSI

Web site at http://webstore.ansi.org/ansidocstore/default.asp.

17 Copies of all NIRMA Technical Guidance documents cited herein may be purchased from the Nuclear Information and Records Management Association, Inc., 10 Almas Road, Windham, NH; telephone (603) 432-6476;

fax (603) 432-3024; see the NIRMA Web site at http://www.nirma.org/member/publications.htm.

18 Copies of this standard are available for purchase from the HPS Web site at http://hps.org/hpssc/n13standards.html.

Rev. 2 of RG 4.15, Page 26

30. ASTM D7282-2006, New Standard Practice for Setup, Calibration, and Quality Control of Instruments Used for Radioactivity Measurements, American Society for Testing and Materials, West Conshohocken, PA, 2006.19

31. ASTM MNL 7A-2002, Manual on Presentation of Data and Control Chart Analysis, 7th Edition, American Society for Testing and Materials, West Conshohocken, PA, 2002.19

32. ANSI N42.22-1995, Traceability of Radioactive Sources to the National Institute of Standards and Technology (NIST) and Associated Instrument Quality Control, American National Standards Institute, New York, NY, 1995 (R2002).16

33. ANSI N42.18-2004, American National Standard Specification and Performance of On-Site Instrumentation for Continuously Monitoring Radioactivity in Effluents, Institute of Electrical and Electronics Engineers, Inc., New York, NY, 1980 (R2004).16

34. EPA QA/G-8-2002, Guidance on Environmental Data Verification and Data Validation, U.S.

Environmental Protection Agency, Washington, DC, EPA/240/R-02/004, November 2002.14

35. IEEE 1063, IEEE Standard for Software User Documentation, Institute of Electrical and Electronics Engineers, Inc. (IEEE), Piscataway, New Jersey, December 2001.20

36. EPA Directive 2185, Good Automated Laboratory Practices, U.S. Environmental Protection Agency (EPA), Office of Information Resources Management, 1995.21

37. Regulatory Guide 1.168, Verification, Validation, Reviews, and Audits for Digital Computer Software Used in Safety Systems of Nuclear Power Plants, U.S. Nuclear Regulatory Commission, Washington, DC.12

38. ANSI N42.14-1999, Calibration and Use of Germanium Spectrometers for the Measurement of Gamma-Ray Emission Rates of Radionuclides, American National Standards Institute, New York, NY, 1999.16

39. International Organization for Standardization (ISO), International Vocabulary of Basic and General Terms in Metrology, 2nd Edition, Geneva, Switzerland, 1993.13

40. ISO Guide 30, Terms and Definitions Used in Connection with Reference Materials, International Organization for Standardization, Geneva, Switzerland, 1992.13

19 Copies of all ASTM standards cited herein may be purchased from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959; see the ASTM International Web-based standards search tool at http://www.astm.org/cgi-bin/SoftCart.exe/NEWSITE_JAVASCRIPT/index.shtml?L+mystore+qkyo3147+117461063.

20

Copies of this standard are available for purchase from the IEEE Web site at http://standards.ieee.org/db/status/index.shtml.

21 Copies of this directive are available electronically from the EPAs public Web site at http://www.epa.gov/irmpoli8/archived/irm_galp/.

Rev. 2 of RG 4.15, Page 27

41. International Union of Pure and Applied Chemistry (IUPAC), Nomenclature for Radioanalytical Chemistry, Pure and Applied Chemistry, 66:12, pp. 2513-2526, 1994.22

42. ISO/IEC 15288-2002, System Engineering System Life Cycle Processes, International Organization for Standardization, Geneva, Switzerland, 2002.13

22 Copies are available electronically through the IUPAC public Web site at http://www.iupac.org/publications/pac/1994/6612/index.html.

Rev. 2 of RG 4.15, Page 28


Retrieved from "https://kanterella.com/w/index.php?title=Regulatory_Guide_4.15&oldid=2576155"