ML16258A074: Difference between revisions
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
StriderTol (talk | contribs) (Created page by program invented by StriderTol) |
||
Line 67: | Line 67: | ||
associated Conditions no longer exist. The individual LCO's | associated Conditions no longer exist. The individual LCO's | ||
ACTIONS specify the Required Actions where this is the case | ACTIONS specify the Required Actions where this is the case (e.g., LCO 3.4.3). | ||
(e.g., LCO 3.4.3). | |||
The Completion Times of the Required Actions are also applicable when a system or component is removed from | The Completion Times of the Required Actions are also applicable when a system or component is removed from | ||
Line 75: | Line 73: | ||
service intentionally. The reasons for intentionally | service intentionally. The reasons for intentionally | ||
relying on the ACTIONS include, but are not limited to, | relying on the ACTIONS include, but are not limited to, performance of Surveillance Requirements (SRs), preventive | ||
performance of Surveillance Requirements (SRs), preventive | |||
maintenance, corrective maintenance, or investigation of | maintenance, corrective maintenance, or investigation of | ||
Line 164: | Line 160: | ||
interpretation of specified times to complete the actions of | interpretation of specified times to complete the actions of | ||
LCO 3.0.3 are consistent with the discussion of Section 1.3, | LCO 3.0.3 are consistent with the discussion of Section 1.3, Completion Times. | ||
Completion Times. | |||
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-4 Revision 2 A unit shutdown required in accordance with LCO 3.0.3 may be terminated, and LCO 3.0.3 exited, if any of the following occurs: a. The LCO has been met. b. A Condition exists for which the Required Actions have been performed. c. ACTIONS exist that do not have expired Completion Times. These Completion Times are applicable from that point in time the Condition is initially entered, and not from the time LCO 3.0.3 is exited. | LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-4 Revision 2 A unit shutdown required in accordance with LCO 3.0.3 may be terminated, and LCO 3.0.3 exited, if any of the following occurs: a. The LCO has been met. b. A Condition exists for which the Required Actions have been performed. c. ACTIONS exist that do not have expired Completion Times. These Completion Times are applicable from that point in time the Condition is initially entered, and not from the time LCO 3.0.3 is exited. | ||
Line 182: | Line 176: | ||
allowable time to reach MODE 5, or other applicable MODE, is | allowable time to reach MODE 5, or other applicable MODE, is | ||
not reduced. For example, if MODE 3 is reached in 2 hours, the time allowed for reaching MODE 4 is the next 11 hours, | not reduced. For example, if MODE 3 is reached in 2 hours, the time allowed for reaching MODE 4 is the next 11 hours, because the total time for reaching MODE 4 is not reduced | ||
because the total time for reaching MODE 4 is not reduced | |||
from the allowable limit of 13 hours. Therefore, if | from the allowable limit of 13 hours. Therefore, if | ||
Line 278: | Line 270: | ||
Actions and must be reopened to perform the required | Actions and must be reopened to perform the required | ||
testing. | testing. An example of demonstrating the OPERABILITY of other equipment is taking an inoperable channel or trip system out | ||
An example of demonstrating the OPERABILITY of other equipment is taking an inoperable channel or trip system out | |||
of the tripped condition to prevent the trip function from | of the tripped condition to prevent the trip function from | ||
Line 299: | Line 290: | ||
The Nuclear Regulatory Commission (NRC) staff has provided a Technical Specification interpretation for LCO 3.0.5 in a | The Nuclear Regulatory Commission (NRC) staff has provided a Technical Specification interpretation for LCO 3.0.5 in a | ||
letter from D. V. Pickett (NRC) to G. H. Gellrich (CCNPP), | letter from D. V. Pickett (NRC) to G. H. Gellrich (CCNPP), | ||
dated December 20, 2011. The NRC staff concluded that | dated December 20, 2011. The NRC staff concluded that | ||
Technical Specification Required Actions 3.3.7.B.1, | Technical Specification Required Actions 3.3.7.B.1, 3.3.8.A.1, 3.4.11.A.1, 3.4.11.C.1, 3.7.3.A.1, and 3.7.8.A.1 | ||
3.3.8.A.1, 3.4.11.A.1, 3.4.11.C.1, 3.7.3.A.1, and 3.7.8.A.1 | |||
are within the scope of the administrative controls applied | are within the scope of the administrative controls applied | ||
Line 311: | Line 299: | ||
by LCO 3.0.5 for the purpose of realignment of components | by LCO 3.0.5 for the purpose of realignment of components | ||
needed for conducting the operability testing on equipment, | needed for conducting the operability testing on equipment, so long as the testing could not be conducted while relying | ||
so long as the testing could not be conducted while relying | |||
on the Technical Specification Required Actions. This | on the Technical Specification Required Actions. This | ||
Line 416: | Line 402: | ||
exists in Systems 2, 4, 5, 8, 9, 10, and 11. | exists in Systems 2, 4, 5, 8, 9, 10, and 11. | ||
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-12 Revision 45 TRAIN A TRAIN B System 8 System 8 System 4 System 4 System 9 System 9 System 2 System 2 System 10 System 10 System 5 System 5 System 11 System 11System 1 System 1 System 12 System 12 System 6 System 6 System 13 System 13 System 3 System 3 System 14 System 14 System 7 System 7 System 15 System 15 If this evaluation determines that a loss of safety function exists, the appropriate Conditions and Required Actions of | LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-12 Revision 45 TRAIN A TRAIN B System 8 System 8 System 4 System 4 System 9 System 9 System 2 System 2 System 10 System 10 System 5 System 5 System 11 System 11System 1 System 1 System 12 System 12 System 6 System 6 System 13 System 13 System 3 System 3 System 14 System 14 System 7 System 7 System 15 System 15 If this evaluation determines that a loss of safety function exists, the appropriate Conditions and Required Actions of | ||
the LCO in which the loss of safety function exists are required to be entered. | the LCO in which the loss of safety function exists are required to be entered. | ||
Line 433: | Line 419: | ||
otherwise could not be performed if required to comply with | otherwise could not be performed if required to comply with | ||
these Technical Specifications. Unless otherwise specified, | these Technical Specifications. Unless otherwise specified, all the other Technical Specification requirements remain | ||
all the other Technical Specification requirements remain | |||
unchanged. This will ensure all appropriate requirements of | unchanged. This will ensure all appropriate requirements of | ||
Line 522: | Line 506: | ||
inoperable snubbers affect separate trains of a system or | inoperable snubbers affect separate trains of a system or | ||
one inoperable snubber affects multiple trains of a system, | one inoperable snubber affects multiple trains of a system, LCO 3.0.8.b is applicable. The supported system must not be | ||
LCO 3.0.8.b is applicable. The supported system must not be | |||
inoperable for any reason other than a lack of seismic | inoperable for any reason other than a lack of seismic | ||
Line 546: | Line 528: | ||
Industry and the Nuclear Regulatory Commission (NRC) guidance on the implementation of 10 CFR 50.65(a)(4) (the | Industry and the Nuclear Regulatory Commission (NRC) guidance on the implementation of 10 CFR 50.65(a)(4) (the | ||
Maintenance Rule) does not address seismic risk. However, | Maintenance Rule) does not address seismic risk. However, use of LCO 3.0.8 must be considered with respect to other | ||
use of LCO 3.0.8 must be considered with respect to other | |||
plant maintenance activities, and integrated into the | plant maintenance activities, and integrated into the | ||
Line 585: | Line 565: | ||
providing their related support function(s). | providing their related support function(s). | ||
Barriers are doors, walls, floor plugs, curbs, hatches, | Barriers are doors, walls, floor plugs, curbs, hatches, installed structures or components, or other devices, not | ||
installed structures or components, or other devices, not | |||
explicitly described in Technical Specifications, that | explicitly described in Technical Specifications, that | ||
Line 729: | Line 707: | ||
respond to emergent conditions that would otherwise likely | respond to emergent conditions that would otherwise likely | ||
lead to entry into LCO 3.0.3 and a rapid plant shutdown, | lead to entry into LCO 3.0.3 and a rapid plant shutdown, which is not justified given the low probability of an | ||
which is not justified given the low probability of an | |||
initiating event which would require the barrier(s) not | initiating event which would require the barrier(s) not | ||
Line 748: | Line 724: | ||
SR 3.0.1 Surveillance Requirement 3.0.1 establishes that SRs must be met during the MODEs or other specified conditions in the | SR 3.0.1 Surveillance Requirement 3.0.1 establishes that SRs must be met during the MODEs or other specified conditions in the | ||
Applicability for which the requirements of the LCO apply, | Applicability for which the requirements of the LCO apply, unless otherwise specified in the individual SRs. This | ||
unless otherwise specified in the individual SRs. This | |||
Specification is to ensure that Surveillances are performed to verify the OPERABILITY of systems and components, and | Specification is to ensure that Surveillances are performed to verify the OPERABILITY of systems and components, and | ||
Line 769: | Line 743: | ||
Surveillances do not have to be performed when the unit is in a MODE or other specified condition for which the | Surveillances do not have to be performed when the unit is in a MODE or other specified condition for which the | ||
requirements of the associated LCO are not applicable, | requirements of the associated LCO are not applicable, unless otherwise specified. The SRs associated with a STE | ||
unless otherwise specified. The SRs associated with a STE | |||
are only applicable when the STE is used as an allowable | are only applicable when the STE is used as an allowable | ||
Line 831: | Line 803: | ||
periodic performance of the Required Action on a "once per . | periodic performance of the Required Action on a "once per . | ||
. ." interval. | . ." interval. | ||
Surveillance Requirement 3.0.2 permits a 25% extension of the interval specified in the Frequency. This extension | Surveillance Requirement 3.0.2 permits a 25% extension of the interval specified in the Frequency. This extension | ||
Line 881: | Line 852: | ||
Surveillance has not been completed within the specified Frequency. A delay period of up to 24 hours or up to the | Surveillance has not been completed within the specified Frequency. A delay period of up to 24 hours or up to the | ||
limit of the specified Frequency, whichever is greater, | limit of the specified Frequency, whichever is greater, applies from the point in time that it is discovered that the Surveillance has not been performed in accordance with SR 3.0.2, and not at the time that the specified Frequency | ||
applies from the point in time that it is discovered that the Surveillance has not been performed in accordance with SR 3.0.2, and not at the time that the specified Frequency | |||
was not met. | was not met. | ||
Line 940: | Line 909: | ||
perform the Surveillance) and impact on any analysis | perform the Surveillance) and impact on any analysis | ||
assumptions, in addition to unit conditions, planning, | assumptions, in addition to unit conditions, planning, availability of personnel, and the time required to perform | ||
availability of personnel, and the time required to perform | |||
the Surveillance. This risk impact should be managed | the Surveillance. This risk impact should be managed | ||
Line 948: | Line 915: | ||
through the program in place to implement 10 CFR 50.65(a)(4) | through the program in place to implement 10 CFR 50.65(a)(4) | ||
and its implementation guidance, NRC Regulatory Guide 1.182, | and its implementation guidance, NRC Regulatory Guide 1.182, "Assessing and Managing Risk Before Maintenance Activities | ||
"Assessing and Managing Risk Before Maintenance Activities | |||
at Nuclear Power Plants." This Regulatory Guide addresses | at Nuclear Power Plants." This Regulatory Guide addresses | ||
consideration of temporary and aggregate risk impacts, | consideration of temporary and aggregate risk impacts, determination of risk management action thresholds, and risk | ||
determination of risk management action thresholds, and risk | |||
management action up to and including plant shutdown. The | management action up to and including plant shutdown. The | ||
Line 1,013: | Line 976: | ||
However, in certain circumstances, failing to meet an SR will not result in SR 3.0.4 restricting a MODE change or | However, in certain circumstances, failing to meet an SR will not result in SR 3.0.4 restricting a MODE change or | ||
other specified condition change. When a system, subsystem, | other specified condition change. When a system, subsystem, division, component, device, or variable is inoperable or | ||
division, component, device, or variable is inoperable or | |||
outside its specified limits, the associated SR(s) are not | outside its specified limits, the associated SR(s) are not | ||
Line 1,031: | Line 992: | ||
perform the Surveillance(s) within the specified Frequency SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-24 Revision 55 does not result in an SR 3.0.4 restriction to changing MODES or other specified conditions of the Applicability. | perform the Surveillance(s) within the specified Frequency SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-24 Revision 55 does not result in an SR 3.0.4 restriction to changing MODES or other specified conditions of the Applicability. | ||
However, since the LCO is not met in this instance, | However, since the LCO is not met in this instance, LCO 3.0.4 will govern any restrictions that may (or may not) | ||
LCO 3.0.4 will govern any restrictions that may (or may not) | |||
apply to MODE or other specified condition changes. | apply to MODE or other specified condition changes. |
Revision as of 05:52, 8 July 2018
ML16258A074 | |
Person / Time | |
---|---|
Site: | Calvert Cliffs ![]() |
Issue date: | 09/08/2016 |
From: | Exelon Generation Co |
To: | Office of Nuclear Reactor Regulation |
Shared Package | |
ML16258A079 | List: |
References | |
Download: ML16258A074 (24) | |
Text
LCO Applicability B 3.0 B 3.0 LIMITING CONDITION FOR OPERATION (LCO) APPLICABILITY
BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-1 Revision 55 LCOs Limiting Condition for Operation (LCO) 3.0.1 through LCO 3.0.9 establish the general requirements applicable to
all Specifications and apply at all times unless otherwise stated. LCO 3.0.1 Limiting Condition for Operation 3.0.1 establishes the Applicability statement within each individual Specification
as the requirement for when the LCO is required to be met (i.e., when the unit is in the MODEs or other specified
conditions of the Applicability statement of each Specification).
LCO 3.0.2 Limiting Condition for Operation 3.0.2 establishes that, upon discovery of a failure to meet an LCO, the associated
ACTIONS shall be met. The Completion Time of each Required
Action for an ACTIONS Condition is applicable from the point in time that an ACTIONS Condition is entered. The Required Actions establish those remedial measures that must be taken
within specified Completion Times when the requirements of
an LCO are not met. This Specification establishes: a. Completion of the Required Actions within the specified Completion Times constitutes compliance with a
Specification; and b. Completion of the Required Actions is not required when an LCO is met within the specified Completion Time, unless otherwise specified.
There are two basic types of Required Actions. The first type of Required Action specifies a time limit in which the LCO must be met. This time limit is the Completion Time to restore an inoperable system or component to OPERABLE status
or to restore variables to within specified limits. If this
type of Required Action is not completed within the
specified Completion Time, a shutdown may be required to
place the unit in a MODE or condition in which the
Specification is not applicable. (Whether stated as a
Required Action or not, correction of the entered Condition
is an action that may always be considered upon entering
ACTIONS.) The second type of Required Action specifies the
remedial measures, that permit continued operation of the unit, that is not further restricted by the Completion Time.
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-2 Revision 55 In this case, compliance with the Required Actions provides an acceptable level of safety for continued operation.
Completing the Required Actions is not required when an LCO is met or is no longer applicable, unless otherwise stated
in the individual Specifications.
The nature of some Required Actions of some Conditions necessitates that, once the Condition is entered, the
Required Actions must be completed even though the
associated Conditions no longer exist. The individual LCO's
ACTIONS specify the Required Actions where this is the case (e.g., LCO 3.4.3).
The Completion Times of the Required Actions are also applicable when a system or component is removed from
service intentionally. The reasons for intentionally
relying on the ACTIONS include, but are not limited to, performance of Surveillance Requirements (SRs), preventive
maintenance, corrective maintenance, or investigation of
operational problems. Entering ACTIONS for these reasons
must be done in a manner that does not compromise safety.
Intentional entry into ACTIONS should not be made for
operational convenience. Additionally, if intentional entry
into ACTIONS would result in redundant equipment being
inoperable, alternatives should be used. Doing so limits
the time both subsystems/trains of a safety function are
inoperable and limits the time conditions exist that may
result in LCO 3.0.3 being entered. Individual
Specifications may specify a time limit for performing an SR when equipment is removed from service or bypassed for
testing. In this case, the Completion Times of the Required
Actions are applicable when this time limit expires if the
equipment remains removed from service or bypassed.
When a change in MODE or other specified condition is required to comply with Required Actions, the unit may enter
a MODE or other specified condition in which another
Specification becomes applicable. In this case, the
Completion Times of the associated Required Actions would
apply from the point in time that the new Specification becomes applicable and the ACTIONS Condition(s) are entered.
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-3 Revision 55 LCO 3.0.3 Limiting Condition for Operation 3.0.3 establishes the actions that must be implemented when an LCO is not met and: a. An associated Required Action and Completion Time is not met and no other Condition applies; or b. The condition of the unit is not specifically addressed by the associated ACTIONS. This means that no combination of Conditions stated in the ACTIONS can be made that exactly corresponds to the actual condition
of the unit. Sometimes, possible combinations of
Conditions are such that entering LCO 3.0.3 is
warranted; in such cases, the ACTIONS specifically
state a Condition corresponding to such combinations
and also that LCO 3.0.3 be entered immediately.
This Specification delineates the time limits for placing the unit in a safe MODE, or other specified condition when
operation cannot be maintained within the limits for safe
operation, as defined by the LCO and its ACTIONS. It is not
intended to be used as an operational convenience that
permits routine, voluntary removal of redundant systems or
components from service in lieu of other alternatives that
would not result in redundant systems or components being
Upon entering LCO 3.0.3, 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> is allowed to prepare for an orderly shutdown before initiating a change in unit
operation. This includes time to permit the operator to
coordinate the reduction in electrical generation with the
load dispatcher to ensure the stability and availability of
the electrical grid. The time limits specified to reach
lower MODEs of operation permit the shutdown to proceed in a
controlled and orderly manner that is well within the specified maximum cooldown rate and within the capabilities of the unit, assuming only the minimum required equipment is OPERABLE. This reduces thermal stresses on components of the Reactor Coolant System and the potential for a plant
upset that could challenge safety systems under the
conditions to which this Specification applies. The use and
interpretation of specified times to complete the actions of
LCO 3.0.3 are consistent with the discussion of Section 1.3, Completion Times.
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-4 Revision 2 A unit shutdown required in accordance with LCO 3.0.3 may be terminated, and LCO 3.0.3 exited, if any of the following occurs: a. The LCO has been met. b. A Condition exists for which the Required Actions have been performed. c. ACTIONS exist that do not have expired Completion Times. These Completion Times are applicable from that point in time the Condition is initially entered, and not from the time LCO 3.0.3 is exited.
The time limits of Specification 3.0.3 allow 37 hours4.282407e-4 days <br />0.0103 hours <br />6.117725e-5 weeks <br />1.40785e-5 months <br /> for the unit to be in MODE 5 when a shutdown is required during
MODE 1 operation. If the unit is in a lower MODE of
operation when a shutdown is required, the time limit for
reaching the next lower MODE applies. If a lower MODE is
reached in less time than allowed, however, the total
allowable time to reach MODE 5, or other applicable MODE, is
not reduced. For example, if MODE 3 is reached in 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br />, the time allowed for reaching MODE 4 is the next 11 hours1.273148e-4 days <br />0.00306 hours <br />1.818783e-5 weeks <br />4.1855e-6 months <br />, because the total time for reaching MODE 4 is not reduced
from the allowable limit of 13 hours1.50463e-4 days <br />0.00361 hours <br />2.149471e-5 weeks <br />4.9465e-6 months <br />. Therefore, if
remedial measures are completed that would permit a return
to MODE 1, a penalty is not incurred by having to reach a
lower MODE of operation in less than the total time allowed.
In MODEs 1, 2, 3, and 4, LCO 3.0.3 provides actions for Conditions not covered in other Specifications. The
requirements of LCO 3.0.3 do not apply in MODEs 5 and 6, because the unit is already in the most restrictive
Condition required.
The requirements of LCO 3.0.3 do not apply in other specified conditions of the Applicability (unless in MODE 1, 2, 3, or 4), because the ACTIONS of individual Specifications sufficiently define the remedial measures to be taken. Exceptions to LCO 3.0.3 are provided in instances
where requiring a unit shutdown, in accordance with
LCO 3.0.3, would not provide appropriate remedial measures
for the associated condition of the unit. An example of
this is in LCO 3.7.13. Limiting Condition for Operation 3.7.13 has an Applicability of "During movement of LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-5 Revision 26 irradiated fuel assemblies in the spent fuel pool."
Therefore, this LCO can be applicable in any or all MODEs.
If the LCO and the Required Actions of LCO 3.7.13 are not
met while in MODE 1, 2, or 3, there is no safety benefit to
be gained by placing the unit in a shutdown condition. The
Required Action of LCO 3.7.13 of "Suspend movement of irradiated fuel assemblies in spent fuel pool" is the appropriate Required Action to complete in lieu of the
actions of LCO 3.0.3. These exceptions are addressed in the individual Specifications.
LCO 3.0.4 Limiting Condition for Operation 3.0.4 establishes limitations on changes in MODES or other specified conditions in the Applicability when an LCO is not met. It
allows placing the unit in a MODE or other specified condition stated in that Applicability (e.g., the Applicability desired to be entered) when unit conditions are such that the requirements of the LCO would not be met, in accordance with LCO 3.0.4.a, LCO 3.0.4.b, or LCO 3.0.4.c.
Limiting Condition for Operation 3.0.4.a allows entry into a MODE or other specified condition in the Applicability with the LCO not met when the associated ACTIONS to be entered permit continued operation in the MODE or other specified condition in the Applicability for an unlimited period of time. Compliance with Required Actions that permit continued operation of the unit for an unlimited period of
time in a MODE or other specified condition provides an
acceptable level of safety for continued operation. This is
without regard to the status of the unit before or after the MODE change. Therefore, in such cases, entry into a MODE or other specified condition in the Applicability may be made
in accordance with the provisions of the Required Actions.
Limiting Condition for Operation 3.0.4.b allows entry into a MODE or other specified condition in the Applicability with the LCO not met after performance of a risk assessment addressing inoperable systems and components, consideration of the results, determination of the acceptability of entering the MODE or other specified condition in the Applicability, and establishment of risk management actions, if appropriate.
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-6 Revision 26 The risk assessment may use quantitative, qualitative, or blended approaches, and the risk assessment will be conducted using the plant program, procedures, and criteria in place to implement 10 CFR 50.65(a)(4), which requires that risk impacts of maintenance activities be assessed and managed. The risk assessment, for the purposes of LCO 3.0.4.b, must take into account all inoperable Technical Specification equipment regardless of whether the equipment is included in the normal 10 CFR 50.65(a)(4) risk assessment scope. The risk assessments will be conducted using the procedures and guidance endorsed by Regulatory Guide 1.182, Assessing and Managing Risk Before Maintenance Activities at Nuclear Power Plants. Regulatory Guide 1.182 endorses the guidance in Section 11 of NUMARC 93-01, Industry Guideline for Monitoring the Effectiveness of Maintenance at Nuclear Power Plants. These documents address general guidance for conduct of the risk assessment, quantitative and qualitative guidelines for establishing risk management actions, and contain example risk management actions. These include actions to plan and conduct other activities in a manner that controls overall risk, increased risk awareness by shift and management personnel, actions to reduce the duration of the condition, actions to minimize the magnitude of risk increases (establishment of backup success paths or compensatory measures), and determination that the proposed MODE change is acceptable. Consideration should also be given to the probability of completing restoration such that the requirements of the LCO would be met prior to the expiration of ACTIONS Completion Times that would require exiting the Applicability.
Limiting Condition for Operation 3.0.4.b may be used with single, or multiple systems and components unavailable.
NUMARC 93-01 provides guidance relative to consideration of simultaneous unavailability of multiple systems and components.
The results of the risk assessment shall be considered in determining the acceptability of entering the MODE or other specified condition in the Applicability, and any corresponding risk management actions. The LCO 3.0.4.b risk assessments do not have to be documented.
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-7 Revision 26 The Technical Specifications allow continued operation with equipment unavailable in MODE 1 for the duration of the Completion Time. Since this is allowable, and since in general the risk impact in that particular MODE bounds the risk of transitioning into and through the applicable MODES or other specified conditions in the Applicability of the LCO, the use of the LCO 3.0.4.b allowance should be generally acceptable, as long as the risk is assessed and managed as stated above. However, there is a small subset of systems and components that have been determined to be more important to risk and use of the LCO 3.0.4.b allowance is prohibited. The LCOs governing these system and components contain Notes prohibiting the use of LCO 3.0.4.b by stating that LCO 3.0.4.b is not applicable.
Limiting Condition for Operation 3.0.4.c allows entry into a MODE or other specified condition in the Applicability with the LCO not met based on a Note in the Specification which states LCO 3.0.4.c is applicable. These specific allowances permit entry into MODES or other specified conditions in the Applicability when the associated ACTIONS to be entered do not provide for continued operation for an unlimited period of time and a risk assessment has not been performed. This allowance may apply to all the ACTIONS or to a specific Required Action of a Specification. The risk assessments performed to justify the use of LCO 3.0.4.b usually only consider systems and components. For this reason, LCO 3.0.4.c is typically applied to Specifications which describe values and parameters (e.g., Pressurizer), and may be applied to other Specifications based on NRC plant-specific approval.
The provisions of this Specification should not be interpreted as endorsing the failure to exercise the good practice of restoring systems or components to OPERABLE status before entering an associated MODE or other specified condition in the Applicability.
The provisions of LCO 3.0.4 shall not prevent changes in MODES or other specified conditions in the Applicability that are required to comply with ACTIONS. In addition, the provisions of LCO 3.0.4 shall not prevent changes in MODES or other specified conditions in the Applicability that LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-8 Revision 26 result from any unit shutdown. In this context, a unit shutdown is defined as a change in MODE or other specified condition in the Applicability associated with transitioning from MODE 1 to MODE 2, MODE 2 to MODE 3, MODE 3 to MODE 4, and MODE 4 to MODE 5.
Upon entry into a MODE or other specified condition in the Applicability with the LCO not met, LCO 3.0.1 and LCO 3.0.2 require entry into the applicable Conditions and Required Actions until the Condition is resolved, until the LCO is met, or until the unit is not within the Applicability of the Technical Specification.
Surveillances do not have to be performed on the associated inoperable equipment (or on variables outside the specified limits), as permitted by SR 3.0.1. Therefore, utilizing LCO 3.0.4 is not a violation of SR 3.0.1 or SR 3.0.4 for any SRs that have not been performed on inoperable equipment.
However, SRs must be met to ensure OPERABILITY prior to
declaring the associated equipment OPERABLE (or variable
within limits) and restoring compliance with the affected LCO. LCO 3.0.5 Limiting Condition for Operation 3.0.5 establishes the allowance for restoring equipment to service under
administrative controls when it has been removed from
service or declared inoperable to comply with ACTIONS. The
sole purpose of this Specification is to provide an
exception to LCO 3.0.2 [e.g., to not comply with the
applicable Required Action(s)]
to allow the performance of required testing to demonstrate: a. The OPERABILITY of the equipment being returned to service; or b. The OPERABILITY of other equipment.
The administrative controls ensure the time the equipment is returned to service (in conflict with the requirements of
the ACTIONS) is limited to the time absolutely necessary to
perform the required testing to demonstrate OPERABILITY.
This Specification does not provide time to perform any
other preventive or corrective maintenance.
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-9 Revision 55 An example of demonstrating the OPERABILITY of the equipment being returned to service is reopening a containment
isolation valve that has been closed to comply with Required
Actions and must be reopened to perform the required
testing. An example of demonstrating the OPERABILITY of other equipment is taking an inoperable channel or trip system out
of the tripped condition to prevent the trip function from
occurring during the performance of required testing on
another channel in the other trip system. A similar example
of demonstrating the OPERABILITY of other equipment is
taking an inoperable channel or trip system out of the
tripped condition to permit the logic to function and
indicate the appropriate response during the performance of
required testing on another channel in the same trip system.
The Nuclear Regulatory Commission (NRC) staff has provided a Technical Specification interpretation for LCO 3.0.5 in a
letter from D. V. Pickett (NRC) to G. H. Gellrich (CCNPP),
dated December 20, 2011. The NRC staff concluded that
Technical Specification Required Actions 3.3.7.B.1, 3.3.8.A.1, 3.4.11.A.1, 3.4.11.C.1, 3.7.3.A.1, and 3.7.8.A.1
are within the scope of the administrative controls applied
by LCO 3.0.5 for the purpose of realignment of components
needed for conducting the operability testing on equipment, so long as the testing could not be conducted while relying
on the Technical Specification Required Actions. This
includes repositioning of redundant or alternate equipment
or trains previously manipulated to comply with the
Technical Specification Required Action. The NRC staff
further concluded that LCO 3.0.5 would apply in all cases to
systems or components in Section 3 of the Technical Specifications.
LCO 3.0.6 Limiting Condition for Operation 3.0.6 establishes an exception to LCO 3.0.2 for support systems that have an LCO
specified in the Technical Specifications. This exception
is provided because LCO 3.0.2 would require the Conditions
and Required Actions of the associated inoperable supported
system LCO be entered solely due to the inoperability of the support system. This exception is justified because the
actions that are required to ensure the unit is maintained LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-10 Revision 55 in a safe condition are specified in the support system LCO's Required Actions. These Required Actions may include
entering the supported system's Conditions and Required
Actions or may specify other Required Actions.
When a support system is inoperable and there is an LCO specified for it in the Technical Specification, the supported system(s) are required to be declared inoperable
if they are determined to be inoperable as a result of the
support system inoperability. However, it is not necessary
to enter into the supported systems' Conditions and Required
Actions unless directed to do so by the support system's
Required Actions. The potential confusion and inconsistency
of requirements related to the entry into multiple support
and supported systems' LCOs' Conditions and Required Actions are eliminated by providing all the actions that are necessary to ensure the unit is maintained in a safe
condition in the support system's Required Actions.
However, there are instances where a support system's Required Action may either direct a supported system to be
declared inoperable or direct entry into Conditions and
Required Actions for the supported system. This may occur
immediately or after some specified delay to perform some
other Required Action. Regardless of whether it is
immediate or after some delay, when a support system's
Required Action directs a supported system to be declared
inoperable or directs entry into Conditions and Required
Actions for a supported system, the applicable Conditions
and Required Actions shall be entered in accordance with
Specification 5.5.15, "Safety Function Determination Program (SFDP)," ensures loss of safety function is detected and appropriate actions are taken. Upon entry into LCO 3.0.6, an evaluation shall be made to determine if a loss of safety
function exists. Additionally, other limitations, remedial
actions, or compensatory actions may be identified as a
result of the support system inoperability and corresponding
exception to entering supported system Conditions and
Required Actions. The SFDP implements the requirements of
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-11 Revision 55 Cross-train checks to identify a loss of safety function for those support systems supporting multiple and redundant
safety systems are required. The cross-train check verifies
that the supported systems of the redundant OPERABLE support
system are OPERABLE, thereby ensuring safety function is
retained. A loss of safety function may exist when a support system is inoperable, and: a. A required system redundant to system(s) supported by the inoperable support system is also inoperable; or EXAMPLE B3.0.6-1 If System 2 of Train A is inoperable, and System 5 of Train B is inoperable, a loss of safety function
exists in supported Systems 5, 10, and 11. b. A required system redundant to system(s) in turn supported by the inoperable supported system is also
inoperable; or EXAMPLE B3.0.6-2 If System 2 of Train A is inoperable, and System 11 of Train B is inoperable, a loss of safety function
exists in System 11. c. A required system redundant to support system(s) for the supported systems (a) and (b) above is also
inoperable. EXAMPLE B3.0.6-3 If System 2 of Train A is inoperable, and System 1 of Train B is inoperable, a loss of safety function
exists in Systems 2, 4, 5, 8, 9, 10, and 11.
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-12 Revision 45 TRAIN A TRAIN B System 8 System 8 System 4 System 4 System 9 System 9 System 2 System 2 System 10 System 10 System 5 System 5 System 11 System 11System 1 System 1 System 12 System 12 System 6 System 6 System 13 System 13 System 3 System 3 System 14 System 14 System 7 System 7 System 15 System 15 If this evaluation determines that a loss of safety function exists, the appropriate Conditions and Required Actions of
the LCO in which the loss of safety function exists are required to be entered.
LCO 3.0.7 There are certain special tests and operations required to be performed at various times over the life of the unit.
These special tests and operations are necessary to
demonstrate select unit performance characteristics, to
perform special maintenance activities, and to perform
special evolutions. Special Test Exception (STE)
LCOs 3.1.7, 3.1.8, and 3.4.17 allow specific Technical Specification requirements to be changed to permit performances of these special tests and operations, which
otherwise could not be performed if required to comply with
these Technical Specifications. Unless otherwise specified, all the other Technical Specification requirements remain
unchanged. This will ensure all appropriate requirements of
the MODE, or other specified condition not directly
associated with or required to be changed to perform the
special test or operation, will remain in effect.
The Applicability of a STE LCO represents a condition not necessarily in compliance with the normal requirements of LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-13 Revision 55 the Technical Specification. Compliance with STE LCOs is optional. A special operation may be performed either under
the provisions of the appropriate STE LCO or under the other
applicable Technical Specification requirements. If it is
desired to perform the special operation under the
provisions of the STE LCO, the requirements of the STE LCO shall be followed.
LCO 3.0.8 LCO 3.0.8 establishes conditions under which systems are considered to remain capable of performing their intended
safety function when associated seismic-designated snubbers
are not capable of providing their associated support
function(s). This LCO states that the supported system is
not considered to be inoperable solely due to one or more
snubbers not capable of performing their associated support
function(s). This is appropriate because a limited length
of time is allowed for maintenance, testing, or repair of
one or more snubbers not capable of performing their
associated support function(s) and appropriate compensatory
measures are specified in the snubber requirements, which
are located outside of the Technical Specifications in the
Technical Requirements Manual (TRM). The snubber
requirements do not meet the criteria in 10 CFR
50.36(d)(2)(ii), and, as such, are appropriate for control
by the TRM.
If the allowed time expires and the snubber(s) are unable to
perform their associated support function(s), the affected
supported system's LCO must be declared not met and the
Conditions and Required Actions entered in accordance with
LCO 3.0.8.a applies when one or more snubbers are not
capable of providing their associated support function(s) to a single train or subsystem of a multiple train or subsystem supported system or to a single train or subsystem of a
single train system. The supported system must not be
inoperable for any reason other than a lack of seismic
support. The LCO allows 72 hours8.333333e-4 days <br />0.02 hours <br />1.190476e-4 weeks <br />2.7396e-5 months <br /> to restore the snubber(s)
before declaring the supported system inoperable. The
72 hour8.333333e-4 days <br />0.02 hours <br />1.190476e-4 weeks <br />2.7396e-5 months <br /> Completion Time is reasonable based on the low
probability of a seismic event concurrent with an event that
would require operation of the supported system occurring LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-14 Revision 55 while the snubber(s) are not capable of performing their associated support function and due to the availability of
the redundant train of the supported system.
LCO 3.0.8.b applies when one or more snubbers are not
capable of providing their associated support function(s) to more than one train or subsystem of a multiple train or subsystem supported system. For example, if multiple
inoperable snubbers affect separate trains of a system or
one inoperable snubber affects multiple trains of a system, LCO 3.0.8.b is applicable. The supported system must not be
inoperable for any reason other than a lack of seismic
support. The LCO allows 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> to restore the snubber(s)
before declaring the supported system inoperable. The
12 hour1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> Completion Time is reasonable based on the low
probability of a seismic event concurrent with an event that
would require operation of the supported system occurring
while the snubber(s) are not capable of performing their
associated support function.
LCO 3.0.8 requires that risk be assessed and managed.
Industry and the Nuclear Regulatory Commission (NRC) guidance on the implementation of 10 CFR 50.65(a)(4) (the
Maintenance Rule) does not address seismic risk. However, use of LCO 3.0.8 must be considered with respect to other
plant maintenance activities, and integrated into the
existing Maintenance Rule process to the extent possible so
that maintenance of any unaffected train or subsystem is
properly controlled, and emergent issues are properly
addressed. The risk assessment need not be quantified, but
may be a qualitative awareness of the vulnerability of
systems and components when one or more snubbers are not
able to perform their associated support function.
The NRC placed several conditions on the use of LCO 3.0.8:
- a. When LCO 3.0.8.a is used, one auxiliary feedwater (AFW) train not associated with the inoperable snubber must
be available.
- b. When LCO 3.0.8.b is used, either one AFW train not associated with the inoperable snubber or some LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-15 Revision 55 alternative means of core cooling (e.g., once-through core cooling) must be available.
- c. When the provisions of LCO 3.0.8 are used, confirm at least one train or subsystem of systems supported by the inoperable snubbers would remain capable of performing the systems required safety or support function(s) for postulated design loads other than seismic loads.
- d. A record of the design function of the inoperable snubber (i.e., seismic versus non-seismic), the
implementation of any of these conditions, and the
associated plant configuration shall all be available
on a recoverable basis for NRC inspection.
LCO 3.0.9 LCO 3.0.9 establishes conditions under which systems described in the Technical Specifications are considered to
remain OPERABLE when required barriers are not capable of
providing their related support function(s).
Barriers are doors, walls, floor plugs, curbs, hatches, installed structures or components, or other devices, not
explicitly described in Technical Specifications, that
support the performance of the safety function of systems
described in the Technical Specifications. This LCO states
that the supported system is not considered to be inoperable
solely due to required barriers not capable of performing
their related support function(s) under the described
conditions. LCO 3.0.9 allows 30 days before declaring the
supported system(s) inoperable and the LCO(s) associated
with the supported system(s) not met. A maximum time is
placed on each use of this allowance to ensure that as required barriers are found or are otherwise made unavailable, they are restored. However, the allowable
duration may be less than the specified maximum time based
on the risk assessment.
If the allowed time expires and the barriers are unable to
perform their related support function(s), the supported
system's LCO(s) must be declared not met and the Conditions
and Required Actions entered in accordance with LCO 3.0.2.
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-16 Revision 55 This provision does not apply to barriers which support
ventilation systems or to fire barriers. The Technical
Specifications for ventilation systems provide specific
Conditions for inoperable barriers. Fire barriers are
addressed by other regulatory requirements and associated plant programs. This provision does not apply to barriers which are not required to support system OPERABILITY (see
NRC Regulatory Issue Summary 2001-09, "Control of Hazard
Barriers," dated April 2, 2001).
The provisions of LCO 3.0.9 are justified because of the low
risk associated with required barriers not being capable of
performing their related support function. This provision
is based on consideration of the following initiating event
categories:
- Loss of coolant accidents;
- High energy line breaks;
- Feedwater line breaks;
- External flooding;
- Turbine missile ejection; and
- Tornado or high wind.
The risk impact of the barriers which cannot perform their
related support function(s) must be addressed pursuant to
the risk assessment and management provision of the
Maintenance Rule, 10 CFR 50.65(a)(4), and the associated
implementation guidance, Regulatory Guide 1.182, "Assessing
and Managing Risk Before Maintenance Activities at Nuclear
Power Plants." Regulatory Guide 1.182 endorses the guidance
in Section 11 of NUMARC 93-01, "Industry Guideline for
Monitoring the Effectiveness of Maintenance at Nuclear Power
Plants." This guidance provides for the consideration of
dynamic plant configuration issues, emergent conditions, and
other aspects pertinent to plant operation with the barriers
unable to perform their related support function(s). These
considerations may result in risk management and other
compensatory actions being required during the period that
barriers are unable to perform their related support
function(s).
LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-17 Revision 55 LCO 3.0.9 may be applied to one or more trains or subsystems of a system supported by barriers that cannot provide their
related support function(s), provided that risk is assessed
and managed (including consideration of the effects on Large
Early Release and from external events). If applied
concurrently to more than one train or subsystem of a multiple train or subsystem supported system, the barriers supporting each of these trains or subsystems must provide
their related support function(s) for different categories
of initiating events. For example, LCO 3.0.9 may be applied
for up to 30 days for more than one train of a multiple
train supported system if the affected barrier for one train
protects against internal flooding and the affected barrier
for the other train protects against tornado missiles. In
this example, the affected barrier may be the same physical
barrier but serve different protection functions for each
train.
If during the time that LCO 3.0.9 is being used, the
required OPERABLE train or subsystem becomes inoperable, it
must be restored to OPERABLE status within 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />.
Otherwise, the train(s) or subsystem(s) supported by
barriers that cannot perform their related support
function(s) must be declared inoperable and the associated
LCOs declared not met. This 24 hour2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> period provides time to
respond to emergent conditions that would otherwise likely
lead to entry into LCO 3.0.3 and a rapid plant shutdown, which is not justified given the low probability of an
initiating event which would require the barrier(s) not
capable of performing their related support function(s).
During this 24 hour2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> period, the plant risk associated with
the existing conditions is assessed and managed in
accordance with 10 CFR 50.65(a)(4).
SR Applicability B 3.0 B 3.0 SURVEILLANCE REQUIREMENT (SR) APPLICABILITY
BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-18 Revision 55 SRs Surveillance Requirement 3.0.1 through SR 3.0.4 establish the general requirements applicable to all Specifications and apply at all times, unless otherwise stated.
SR 3.0.1 Surveillance Requirement 3.0.1 establishes that SRs must be met during the MODEs or other specified conditions in the
Applicability for which the requirements of the LCO apply, unless otherwise specified in the individual SRs. This
Specification is to ensure that Surveillances are performed to verify the OPERABILITY of systems and components, and
that variables are within specified limits. Failure to meet
a SR within the specified Frequency, in accordance with
SR 3.0.2, constitutes a failure to meet an LCO.
Surveillances may be performed by means of any series of sequential, overlapping, or total steps provided the entire Surveillance is performed within the specified Frequency.
Additionally, the definitions related to instrument testing (e.g., CHANNEL CALIBRATION) specify that these tests are performed by means of any series of sequential, overlapping or total steps.
Systems and components are assumed to be OPERABLE when the associated SRs have been met. Nothing in this
Specification, however, is to be construed as implying that
systems or components are OPERABLE when: a. The systems or components are known to be inoperable, although still meeting the SRs; or b. The requirements of the Surveillance(s) are known to be not met between required Surveillance performances.
Surveillances do not have to be performed when the unit is in a MODE or other specified condition for which the
requirements of the associated LCO are not applicable, unless otherwise specified. The SRs associated with a STE
are only applicable when the STE is used as an allowable
exception to the requirements of a Specification.
Unplanned events may satisfy the requirements (including applicable acceptance criteria) for a given SR. In this
case, the unplanned event may be credited as fulfilling the
performance of the SR. This allowance includes those SRs SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-19 Revision 55 whose performance is normally precluded in a given MODE or other specified condition.
Surveillances, including Surveillances invoked by Required Actions, do not have to be performed on inoperable
equipment, because the ACTIONS define the applicable remedial measures that apply. Surveillances have to be met and performed in accordance with SR 3.0.2 prior to returning equipment to OPERABLE status.
Upon completion of maintenance, appropriate post-maintenance testing is required to declare equipment OPERABLE. This
includes ensuring applicable Surveillances are not failed and their most recent performance is in accordance with
SR 3.0.2. Post-maintenance testing may not be possible in
the current MODE or other specified conditions in the
Applicability due to the necessary unit parameters not
having been established. In these situations, the equipment
may be considered OPERABLE provided testing has been
satisfactorily completed to the extent possible and the
equipment is not otherwise believed to be incapable of
performing its function. This will allow operation to
proceed to a MODE or other specified condition where other
necessary post-maintenance tests can be completed. Some examples of this process are: a. Auxiliary feedwater pump turbine maintenance during refueling that requires testing at steam pressures
> 800 psi. However, if other appropriate testing is
satisfactorily completed, the Auxiliary Feedwater
System can be considered OPERABLE. This allows startup
and other necessary testing to proceed until the plant
reaches the steam pressure required to perform the
testing. b. High pressure safety injection maintenance during shutdown that requires system functional tests at a specified pressure. Provided other appropriate testing
is satisfactorily completed, startup can proceed with
high pressure safety injection considered OPERABLE.
This allows operation to reach the specified pressure to complete the necessary post-maintenance testing.
SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-20 Revision 55 SR 3.0.2 Surveillance Requirement 3.0.2 establishes the requirements for meeting the specified Frequency for Surveillances and any Required Action with a Completion Time that requires the
periodic performance of the Required Action on a "once per .
. ." interval.
Surveillance Requirement 3.0.2 permits a 25% extension of the interval specified in the Frequency. This extension
facilitates Surveillance scheduling and considers plant operating conditions that may not be suitable for conducting
the Surveillance (e.g., transient conditions or other ongoing Surveillance or maintenance activities).
The 25% extension does not significantly degrade the reliability that results from performing the Surveillance at its specified Frequency. This is based on the recognition
that the most probable result of any particular Surveillance being performed is the verification of conformance with the
SRs. The exceptions to SR 3.0.2 are those Surveillances for which the 25% extension of the interval specified in the
Frequency does not apply. These exceptions are stated in
the individual Specifications. An example of where SR 3.0.2
does not apply is the Containment Leakage Rate Testing
Program. The program establishes testing requirements and Frequencies in accordance with the requirements of regulations. The Technical Specifications cannot in and of themselves, extend a test interval specified in the regulations.
As stated in SR 3.0.2, the 25% extension also does not apply to the initial portion of a periodic Completion Time that
requires performance on a "once per . . ." basis. The 25%
extension applies to each performance after the initial
performance. The initial performance of the Required Action, whether it is a particular Surveillance or some other remedial action, is considered a single action with a single Completion Time. One reason for not allowing the 25%
extension to this Completion Time is that such an action
usually verifies that no loss of function has occurred by
checking the status of redundant or diverse components or
accomplishes the function of the inoperable equipment in an
alternative manner.
SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-21 Revision 55 The provisions of SR 3.0.2 are not intended to be used repeatedly, merely as an operational convenience to extend
Surveillance intervals (other than those consistent with refueling intervals) or periodic Completion Time intervals beyond those specified.
SR 3.0.3 Surveillance Requirement 3.0.3 establishes the flexibility to defer declaring affected equipment inoperable or an
affected variable outside the specified limits when a
Surveillance has not been completed within the specified Frequency. A delay period of up to 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> or up to the
limit of the specified Frequency, whichever is greater, applies from the point in time that it is discovered that the Surveillance has not been performed in accordance with SR 3.0.2, and not at the time that the specified Frequency
was not met.
This delay period provides an adequate time to complete Surveillances that have been missed. This delay period permits the completion of a Surveillance before complying with Required Actions or other remedial measures that might
preclude completion of the Surveillance.
The basis for this delay period includes consideration of unit conditions, adequate planning, availability of
personnel, the time required to perform the Surveillance, the safety significance of the delay in completing the
required Surveillance, and the recognition that the most probable result of any particular Surveillance being performed is the verification of conformance with the
requirements.
When a Surveillance with a Frequency based not on time intervals, but upon specified unit conditions, operating situations, or requirements of regulations (e.g., prior to entering MODE 1 after each fuel loading, or in accordance
with 10 CFR Part 50, Appendix J, as modified by approved
exemptions, etc.) is discovered to not have been performed
when specified, SR 3.0.3 allows for the full delay period of
up to the specified Frequency to perform the Surveillance.
However, since there is not a time interval specified, the
missed Surveillance should be performed at the first
reasonable opportunity.
SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-22 Revision 55 Surveillance Requirement 3.0.3 provides a time limit for, and allowances for the performance of, Surveillances that
become applicable as a consequence of MODE changes imposed
by Required Actions.
Failure to comply with specified Frequencies for SRs is expected to be an infrequent occurrence. Use of the delay
period established by SR 3.0.3 is a flexibility that is not
intended to be used as an operational convenience to extend
Surveillance intervals. While up to 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> or the limit of the specified Frequency is provided to perform the missed
Surveillance, it is expected that the missed Surveillance
will be performed at the first reasonable opportunity. The
determination of the first reasonable opportunity should
include consideration of the impact on plant risk (from
delaying the Surveillance, as well as any plant
configuration changes required or shutting the plant down to
perform the Surveillance) and impact on any analysis
assumptions, in addition to unit conditions, planning, availability of personnel, and the time required to perform
the Surveillance. This risk impact should be managed
through the program in place to implement 10 CFR 50.65(a)(4)
and its implementation guidance, NRC Regulatory Guide 1.182, "Assessing and Managing Risk Before Maintenance Activities
at Nuclear Power Plants." This Regulatory Guide addresses
consideration of temporary and aggregate risk impacts, determination of risk management action thresholds, and risk
management action up to and including plant shutdown. The
missed Surveillance should be treated as an emergent
condition as discussed in the Regulatory Guide. The risk
evaluation may use quantitative, qualitative, or blended
methods. The degree of depth and rigor of the evaluation
should be commensurate with the importance of the component.
Missed Surveillances for important components should be analyzed quantitatively. If the results of the risk
evaluation determine the risk increase is significant, this
evaluation should be used to determine the safest course of
action. All missed Surveillances will be placed in the
licensee's Corrective Action Program.
If a Surveillance is not completed within the allowed delay period, then the equipment is considered inoperable or the SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-23 Revision 55 variable is considered outside the specified limits, and the Completion Times of the Required Actions for the applicable
LCO Conditions begin immediately upon expiration of the
delay period. If a Surveillance is failed within the delay period, then the equipment is inoperable or the variable is outside the specified limits, and the Completion Times of the Required Actions for the applicable LCO Conditions begin immediately upon the failure of the Surveillance.
Completion of the Surveillance within the delay period allowed by this Specification, or within the Completion Time of the ACTIONS, restores compliance with SR 3.0.1.
SR 3.0.4 Surveillance Requirement 3.0.4 establishes the requirement that all applicable SRs must be met before entry into a MODE
or other specified Condition in the Applicability.
This Specification ensures system and component OPERABILITY requirements and variable limits are met before entry into
MODEs or other specified conditions in the Applicability for
which these systems and components ensure safe operation of
the unit. The provisions of this Specification should not
be interpreted as endorsing the failure to exercise the good
practice of restoring systems or components to OPERABLE
status before entering an associated MODE or other specified
condition in the Applicability.
A provision is included to allow entry into a MODE or other
specified condition in the Applicability when an LCO is not
met due to Surveillance not being met in accordance with LCO 3.0.4.
However, in certain circumstances, failing to meet an SR will not result in SR 3.0.4 restricting a MODE change or
other specified condition change. When a system, subsystem, division, component, device, or variable is inoperable or
outside its specified limits, the associated SR(s) are not
required to be performed, per SR 3.0.1, which states that
Surveillances do not have to be performed on inoperable
equipment. When equipment is inoperable, SR 3.0.4 does not
apply to the associated SR(s) since the requirement for the
SR(s) to be performed is removed. Therefore, failing to
perform the Surveillance(s) within the specified Frequency SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-24 Revision 55 does not result in an SR 3.0.4 restriction to changing MODES or other specified conditions of the Applicability.
However, since the LCO is not met in this instance, LCO 3.0.4 will govern any restrictions that may (or may not)
apply to MODE or other specified condition changes.
Surveillance Requirement 3.0.4 does not restrict changing MODES or other specified conditions of the Applicability when a Surveillance has not been performed within the
specified Frequency, provided the requirement to declare the
LCO not met has been delayed in accordance with SR 3.0.3.
The provisions of SR 3.0.4 shall not prevent entry into MODES or other specified conditions in the Applicability
that are required to comply with ACTIONS. In addition, the
provisions of SR 3.0.4 shall not prevent changes in MODES or
other specified conditions in the Applicability that result
from any unit shutdown. In this context, a unit shutdown is
defined as a change in MODE or other specified condition in
the Applicability associated with transitioning from MODE 1
to MODE 2, MODE 2 to MODE 3, MODE 3 to MODE 4, and MODE 4 to
MODE 5.
The precise requirements for performance of SRs are specified such that exceptions to SR 3.0.4 are not
necessary. The specific time frames and conditions
necessary for meeting the SRs are specified in the
Frequency, in the Surveillance, or both. This allows
performance of Surveillances when the prerequisite
condition(s) specified in a Surveillance procedure require
entry into the MODE or other specified condition in the
Applicability of the associated LCO prior to the performance
or completion of a Surveillance. A Surveillance that could
not be performed until after entering the LCOs
Applicability, would have its Frequency specified such that it is not "due" until the specific conditions needed are met. Alternately, the Surveillance may be stated in the
form of a Note, as not required (to be met or performed)
until a particular event, condition, or time has been
reached. Further discussion of the specific formats of SRs'
annotation is found in Section 1.4, Frequency.