ML16258A074

Calvert Cliffs Nuclear Power Plant Unit Nos. 1 & 2 - Technical Specification Bases B 3.0-1, Limiting Condition for Operation (LCO) Applicability

ML16258A074
Person / Time
Site:	Calvert Cliffs
Issue date:	09/08/2016
From:	Exelon Generation Co
To:	Office of Nuclear Reactor Regulation
Shared Package
ML16258A079	List: ML16258A060 ML16258A072 ML16258A073 ML16258A074 ML16258A075 ML16258A076 ML16258A077 ML16258A078 ML16258A080 ML16258A081 ML16258A082 ML16258A083 ML16258A084
References
Download: ML16258A074 (24)

Text

LCO Applicability B 3.0 B 3.0 LIMITING CONDITION FOR OPERATION (LCO) APPLICABILITY

BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-1 Revision 55 LCOs Limiting Condition for Operation (LCO) 3.0.1 through LCO 3.0.9 establish the general requirements applicable to

all Specifications and apply at all times unless otherwise stated. LCO 3.0.1 Limiting Condition for Operation 3.0.1 establishes the Applicability statement within each individual Specification

as the requirement for when the LCO is required to be met (i.e., when the unit is in the MODEs or other specified

conditions of the Applicability statement of each Specification).

LCO 3.0.2 Limiting Condition for Operation 3.0.2 establishes that, upon discovery of a failure to meet an LCO, the associated

ACTIONS shall be met. The Completion Time of each Required

Action for an ACTIONS Condition is applicable from the point in time that an ACTIONS Condition is entered. The Required Actions establish those remedial measures that must be taken

within specified Completion Times when the requirements of

an LCO are not met. This Specification establishes: a. Completion of the Required Actions within the specified Completion Times constitutes compliance with a

Specification; and b. Completion of the Required Actions is not required when an LCO is met within the specified Completion Time, unless otherwise specified.

There are two basic types of Required Actions. The first type of Required Action specifies a time limit in which the LCO must be met. This time limit is the Completion Time to restore an inoperable system or component to OPERABLE status

or to restore variables to within specified limits. If this

type of Required Action is not completed within the

specified Completion Time, a shutdown may be required to

place the unit in a MODE or condition in which the

Specification is not applicable. (Whether stated as a

Required Action or not, correction of the entered Condition

is an action that may always be considered upon entering

ACTIONS.) The second type of Required Action specifies the

remedial measures, that permit continued operation of the unit, that is not further restricted by the Completion Time.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-2 Revision 55 In this case, compliance with the Required Actions provides an acceptable level of safety for continued operation.

Completing the Required Actions is not required when an LCO is met or is no longer applicable, unless otherwise stated

in the individual Specifications.

The nature of some Required Actions of some Conditions necessitates that, once the Condition is entered, the

Required Actions must be completed even though the

associated Conditions no longer exist. The individual LCO's

ACTIONS specify the Required Actions where this is the case (e.g., LCO 3.4.3).

The Completion Times of the Required Actions are also applicable when a system or component is removed from

service intentionally. The reasons for intentionally

relying on the ACTIONS include, but are not limited to, performance of Surveillance Requirements (SRs), preventive

maintenance, corrective maintenance, or investigation of

operational problems. Entering ACTIONS for these reasons

must be done in a manner that does not compromise safety.

Intentional entry into ACTIONS should not be made for

operational convenience. Additionally, if intentional entry

into ACTIONS would result in redundant equipment being

inoperable, alternatives should be used. Doing so limits

the time both subsystems/trains of a safety function are

inoperable and limits the time conditions exist that may

result in LCO 3.0.3 being entered. Individual

Specifications may specify a time limit for performing an SR when equipment is removed from service or bypassed for

testing. In this case, the Completion Times of the Required

Actions are applicable when this time limit expires if the

equipment remains removed from service or bypassed.

When a change in MODE or other specified condition is required to comply with Required Actions, the unit may enter

a MODE or other specified condition in which another

Specification becomes applicable. In this case, the

Completion Times of the associated Required Actions would

apply from the point in time that the new Specification becomes applicable and the ACTIONS Condition(s) are entered.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-3 Revision 55 LCO 3.0.3 Limiting Condition for Operation 3.0.3 establishes the actions that must be implemented when an LCO is not met and: a. An associated Required Action and Completion Time is not met and no other Condition applies; or b. The condition of the unit is not specifically addressed by the associated ACTIONS. This means that no combination of Conditions stated in the ACTIONS can be made that exactly corresponds to the actual condition

of the unit. Sometimes, possible combinations of

Conditions are such that entering LCO 3.0.3 is

warranted; in such cases, the ACTIONS specifically

state a Condition corresponding to such combinations

and also that LCO 3.0.3 be entered immediately.

This Specification delineates the time limits for placing the unit in a safe MODE, or other specified condition when

operation cannot be maintained within the limits for safe

operation, as defined by the LCO and its ACTIONS. It is not

intended to be used as an operational convenience that

permits routine, voluntary removal of redundant systems or

components from service in lieu of other alternatives that

would not result in redundant systems or components being

inoperable.

Upon entering LCO 3.0.3, 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> is allowed to prepare for an orderly shutdown before initiating a change in unit

operation. This includes time to permit the operator to

coordinate the reduction in electrical generation with the

load dispatcher to ensure the stability and availability of

the electrical grid. The time limits specified to reach

lower MODEs of operation permit the shutdown to proceed in a

controlled and orderly manner that is well within the specified maximum cooldown rate and within the capabilities of the unit, assuming only the minimum required equipment is OPERABLE. This reduces thermal stresses on components of the Reactor Coolant System and the potential for a plant

upset that could challenge safety systems under the

conditions to which this Specification applies. The use and

interpretation of specified times to complete the actions of

LCO 3.0.3 are consistent with the discussion of Section 1.3, Completion Times.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-4 Revision 2 A unit shutdown required in accordance with LCO 3.0.3 may be terminated, and LCO 3.0.3 exited, if any of the following occurs: a. The LCO has been met. b. A Condition exists for which the Required Actions have been performed. c. ACTIONS exist that do not have expired Completion Times. These Completion Times are applicable from that point in time the Condition is initially entered, and not from the time LCO 3.0.3 is exited.

The time limits of Specification 3.0.3 allow 37 hours4.282407e-4 days <br />0.0103 hours <br />6.117725e-5 weeks <br />1.40785e-5 months <br /> for the unit to be in MODE 5 when a shutdown is required during

MODE 1 operation. If the unit is in a lower MODE of

operation when a shutdown is required, the time limit for

reaching the next lower MODE applies. If a lower MODE is

reached in less time than allowed, however, the total

allowable time to reach MODE 5, or other applicable MODE, is

not reduced. For example, if MODE 3 is reached in 2 hours2.314815e-5 days <br />5.555556e-4 hours <br />3.306878e-6 weeks <br />7.61e-7 months <br />, the time allowed for reaching MODE 4 is the next 11 hours1.273148e-4 days <br />0.00306 hours <br />1.818783e-5 weeks <br />4.1855e-6 months <br />, because the total time for reaching MODE 4 is not reduced

from the allowable limit of 13 hours1.50463e-4 days <br />0.00361 hours <br />2.149471e-5 weeks <br />4.9465e-6 months <br />. Therefore, if

remedial measures are completed that would permit a return

to MODE 1, a penalty is not incurred by having to reach a

lower MODE of operation in less than the total time allowed.

In MODEs 1, 2, 3, and 4, LCO 3.0.3 provides actions for Conditions not covered in other Specifications. The

requirements of LCO 3.0.3 do not apply in MODEs 5 and 6, because the unit is already in the most restrictive

Condition required.

The requirements of LCO 3.0.3 do not apply in other specified conditions of the Applicability (unless in MODE 1, 2, 3, or 4), because the ACTIONS of individual Specifications sufficiently define the remedial measures to be taken. Exceptions to LCO 3.0.3 are provided in instances

where requiring a unit shutdown, in accordance with

LCO 3.0.3, would not provide appropriate remedial measures

for the associated condition of the unit. An example of

this is in LCO 3.7.13. Limiting Condition for Operation 3.7.13 has an Applicability of "During movement of LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-5 Revision 26 irradiated fuel assemblies in the spent fuel pool."

Therefore, this LCO can be applicable in any or all MODEs.

If the LCO and the Required Actions of LCO 3.7.13 are not

met while in MODE 1, 2, or 3, there is no safety benefit to

be gained by placing the unit in a shutdown condition. The

Required Action of LCO 3.7.13 of "Suspend movement of irradiated fuel assemblies in spent fuel pool" is the appropriate Required Action to complete in lieu of the

actions of LCO 3.0.3. These exceptions are addressed in the individual Specifications.

LCO 3.0.4 Limiting Condition for Operation 3.0.4 establishes limitations on changes in MODES or other specified conditions in the Applicability when an LCO is not met. It

allows placing the unit in a MODE or other specified condition stated in that Applicability (e.g., the Applicability desired to be entered) when unit conditions are such that the requirements of the LCO would not be met, in accordance with LCO 3.0.4.a, LCO 3.0.4.b, or LCO 3.0.4.c.

Limiting Condition for Operation 3.0.4.a allows entry into a MODE or other specified condition in the Applicability with the LCO not met when the associated ACTIONS to be entered permit continued operation in the MODE or other specified condition in the Applicability for an unlimited period of time. Compliance with Required Actions that permit continued operation of the unit for an unlimited period of

time in a MODE or other specified condition provides an

acceptable level of safety for continued operation. This is

without regard to the status of the unit before or after the MODE change. Therefore, in such cases, entry into a MODE or other specified condition in the Applicability may be made

in accordance with the provisions of the Required Actions.

Limiting Condition for Operation 3.0.4.b allows entry into a MODE or other specified condition in the Applicability with the LCO not met after performance of a risk assessment addressing inoperable systems and components, consideration of the results, determination of the acceptability of entering the MODE or other specified condition in the Applicability, and establishment of risk management actions, if appropriate.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-6 Revision 26 The risk assessment may use quantitative, qualitative, or blended approaches, and the risk assessment will be conducted using the plant program, procedures, and criteria in place to implement 10 CFR 50.65(a)(4), which requires that risk impacts of maintenance activities be assessed and managed. The risk assessment, for the purposes of LCO 3.0.4.b, must take into account all inoperable Technical Specification equipment regardless of whether the equipment is included in the normal 10 CFR 50.65(a)(4) risk assessment scope. The risk assessments will be conducted using the procedures and guidance endorsed by Regulatory Guide 1.182, Assessing and Managing Risk Before Maintenance Activities at Nuclear Power Plants. Regulatory Guide 1.182 endorses the guidance in Section 11 of NUMARC 93-01, Industry Guideline for Monitoring the Effectiveness of Maintenance at Nuclear Power Plants. These documents address general guidance for conduct of the risk assessment, quantitative and qualitative guidelines for establishing risk management actions, and contain example risk management actions. These include actions to plan and conduct other activities in a manner that controls overall risk, increased risk awareness by shift and management personnel, actions to reduce the duration of the condition, actions to minimize the magnitude of risk increases (establishment of backup success paths or compensatory measures), and determination that the proposed MODE change is acceptable. Consideration should also be given to the probability of completing restoration such that the requirements of the LCO would be met prior to the expiration of ACTIONS Completion Times that would require exiting the Applicability.

Limiting Condition for Operation 3.0.4.b may be used with single, or multiple systems and components unavailable.

NUMARC 93-01 provides guidance relative to consideration of simultaneous unavailability of multiple systems and components.

The results of the risk assessment shall be considered in determining the acceptability of entering the MODE or other specified condition in the Applicability, and any corresponding risk management actions. The LCO 3.0.4.b risk assessments do not have to be documented.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-7 Revision 26 The Technical Specifications allow continued operation with equipment unavailable in MODE 1 for the duration of the Completion Time. Since this is allowable, and since in general the risk impact in that particular MODE bounds the risk of transitioning into and through the applicable MODES or other specified conditions in the Applicability of the LCO, the use of the LCO 3.0.4.b allowance should be generally acceptable, as long as the risk is assessed and managed as stated above. However, there is a small subset of systems and components that have been determined to be more important to risk and use of the LCO 3.0.4.b allowance is prohibited. The LCOs governing these system and components contain Notes prohibiting the use of LCO 3.0.4.b by stating that LCO 3.0.4.b is not applicable.

Limiting Condition for Operation 3.0.4.c allows entry into a MODE or other specified condition in the Applicability with the LCO not met based on a Note in the Specification which states LCO 3.0.4.c is applicable. These specific allowances permit entry into MODES or other specified conditions in the Applicability when the associated ACTIONS to be entered do not provide for continued operation for an unlimited period of time and a risk assessment has not been performed. This allowance may apply to all the ACTIONS or to a specific Required Action of a Specification. The risk assessments performed to justify the use of LCO 3.0.4.b usually only consider systems and components. For this reason, LCO 3.0.4.c is typically applied to Specifications which describe values and parameters (e.g., Pressurizer), and may be applied to other Specifications based on NRC plant-specific approval.

The provisions of this Specification should not be interpreted as endorsing the failure to exercise the good practice of restoring systems or components to OPERABLE status before entering an associated MODE or other specified condition in the Applicability.

The provisions of LCO 3.0.4 shall not prevent changes in MODES or other specified conditions in the Applicability that are required to comply with ACTIONS. In addition, the provisions of LCO 3.0.4 shall not prevent changes in MODES or other specified conditions in the Applicability that LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-8 Revision 26 result from any unit shutdown. In this context, a unit shutdown is defined as a change in MODE or other specified condition in the Applicability associated with transitioning from MODE 1 to MODE 2, MODE 2 to MODE 3, MODE 3 to MODE 4, and MODE 4 to MODE 5.

Upon entry into a MODE or other specified condition in the Applicability with the LCO not met, LCO 3.0.1 and LCO 3.0.2 require entry into the applicable Conditions and Required Actions until the Condition is resolved, until the LCO is met, or until the unit is not within the Applicability of the Technical Specification.

Surveillances do not have to be performed on the associated inoperable equipment (or on variables outside the specified limits), as permitted by SR 3.0.1. Therefore, utilizing LCO 3.0.4 is not a violation of SR 3.0.1 or SR 3.0.4 for any SRs that have not been performed on inoperable equipment.

However, SRs must be met to ensure OPERABILITY prior to

declaring the associated equipment OPERABLE (or variable

within limits) and restoring compliance with the affected LCO. LCO 3.0.5 Limiting Condition for Operation 3.0.5 establishes the allowance for restoring equipment to service under

administrative controls when it has been removed from

service or declared inoperable to comply with ACTIONS. The

sole purpose of this Specification is to provide an

exception to LCO 3.0.2 [e.g., to not comply with the

applicable Required Action(s)]

to allow the performance of required testing to demonstrate: a. The OPERABILITY of the equipment being returned to service; or b. The OPERABILITY of other equipment.

The administrative controls ensure the time the equipment is returned to service (in conflict with the requirements of

the ACTIONS) is limited to the time absolutely necessary to

perform the required testing to demonstrate OPERABILITY.

This Specification does not provide time to perform any

other preventive or corrective maintenance.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-9 Revision 55 An example of demonstrating the OPERABILITY of the equipment being returned to service is reopening a containment

isolation valve that has been closed to comply with Required

Actions and must be reopened to perform the required

testing. An example of demonstrating the OPERABILITY of other equipment is taking an inoperable channel or trip system out

of the tripped condition to prevent the trip function from

occurring during the performance of required testing on

another channel in the other trip system. A similar example

of demonstrating the OPERABILITY of other equipment is

taking an inoperable channel or trip system out of the

tripped condition to permit the logic to function and

indicate the appropriate response during the performance of

required testing on another channel in the same trip system.

The Nuclear Regulatory Commission (NRC) staff has provided a Technical Specification interpretation for LCO 3.0.5 in a

letter from D. V. Pickett (NRC) to G. H. Gellrich (CCNPP),

dated December 20, 2011. The NRC staff concluded that

Technical Specification Required Actions 3.3.7.B.1, 3.3.8.A.1, 3.4.11.A.1, 3.4.11.C.1, 3.7.3.A.1, and 3.7.8.A.1

are within the scope of the administrative controls applied

by LCO 3.0.5 for the purpose of realignment of components

needed for conducting the operability testing on equipment, so long as the testing could not be conducted while relying

on the Technical Specification Required Actions. This

includes repositioning of redundant or alternate equipment

or trains previously manipulated to comply with the

Technical Specification Required Action. The NRC staff

further concluded that LCO 3.0.5 would apply in all cases to

systems or components in Section 3 of the Technical Specifications.

LCO 3.0.6 Limiting Condition for Operation 3.0.6 establishes an exception to LCO 3.0.2 for support systems that have an LCO

specified in the Technical Specifications. This exception

is provided because LCO 3.0.2 would require the Conditions

and Required Actions of the associated inoperable supported

system LCO be entered solely due to the inoperability of the support system. This exception is justified because the

actions that are required to ensure the unit is maintained LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-10 Revision 55 in a safe condition are specified in the support system LCO's Required Actions. These Required Actions may include

entering the supported system's Conditions and Required

Actions or may specify other Required Actions.

When a support system is inoperable and there is an LCO specified for it in the Technical Specification, the supported system(s) are required to be declared inoperable

if they are determined to be inoperable as a result of the

support system inoperability. However, it is not necessary

to enter into the supported systems' Conditions and Required

Actions unless directed to do so by the support system's

Required Actions. The potential confusion and inconsistency

of requirements related to the entry into multiple support

and supported systems' LCOs' Conditions and Required Actions are eliminated by providing all the actions that are necessary to ensure the unit is maintained in a safe

condition in the support system's Required Actions.

However, there are instances where a support system's Required Action may either direct a supported system to be

declared inoperable or direct entry into Conditions and

Required Actions for the supported system. This may occur

immediately or after some specified delay to perform some

other Required Action. Regardless of whether it is

immediate or after some delay, when a support system's

Required Action directs a supported system to be declared

inoperable or directs entry into Conditions and Required

Actions for a supported system, the applicable Conditions

and Required Actions shall be entered in accordance with

LCO 3.0.2.

Specification 5.5.15, "Safety Function Determination Program (SFDP)," ensures loss of safety function is detected and appropriate actions are taken. Upon entry into LCO 3.0.6, an evaluation shall be made to determine if a loss of safety

function exists. Additionally, other limitations, remedial

actions, or compensatory actions may be identified as a

result of the support system inoperability and corresponding

exception to entering supported system Conditions and

Required Actions. The SFDP implements the requirements of

LCO 3.0.6.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-11 Revision 55 Cross-train checks to identify a loss of safety function for those support systems supporting multiple and redundant

safety systems are required. The cross-train check verifies

that the supported systems of the redundant OPERABLE support

system are OPERABLE, thereby ensuring safety function is

retained. A loss of safety function may exist when a support system is inoperable, and: a. A required system redundant to system(s) supported by the inoperable support system is also inoperable; or EXAMPLE B3.0.6-1 If System 2 of Train A is inoperable, and System 5 of Train B is inoperable, a loss of safety function

exists in supported Systems 5, 10, and 11. b. A required system redundant to system(s) in turn supported by the inoperable supported system is also

inoperable; or EXAMPLE B3.0.6-2 If System 2 of Train A is inoperable, and System 11 of Train B is inoperable, a loss of safety function

exists in System 11. c. A required system redundant to support system(s) for the supported systems (a) and (b) above is also

inoperable. EXAMPLE B3.0.6-3 If System 2 of Train A is inoperable, and System 1 of Train B is inoperable, a loss of safety function

exists in Systems 2, 4, 5, 8, 9, 10, and 11.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-12 Revision 45 TRAIN A TRAIN B System 8 System 8 System 4 System 4 System 9 System 9 System 2 System 2 System 10 System 10 System 5 System 5 System 11 System 11System 1 System 1 System 12 System 12 System 6 System 6 System 13 System 13 System 3 System 3 System 14 System 14 System 7 System 7 System 15 System 15 If this evaluation determines that a loss of safety function exists, the appropriate Conditions and Required Actions of

the LCO in which the loss of safety function exists are required to be entered.

LCO 3.0.7 There are certain special tests and operations required to be performed at various times over the life of the unit.

These special tests and operations are necessary to

demonstrate select unit performance characteristics, to

perform special maintenance activities, and to perform

special evolutions. Special Test Exception (STE)

LCOs 3.1.7, 3.1.8, and 3.4.17 allow specific Technical Specification requirements to be changed to permit performances of these special tests and operations, which

otherwise could not be performed if required to comply with

these Technical Specifications. Unless otherwise specified, all the other Technical Specification requirements remain

unchanged. This will ensure all appropriate requirements of

the MODE, or other specified condition not directly

associated with or required to be changed to perform the

special test or operation, will remain in effect.

The Applicability of a STE LCO represents a condition not necessarily in compliance with the normal requirements of LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-13 Revision 55 the Technical Specification. Compliance with STE LCOs is optional. A special operation may be performed either under

the provisions of the appropriate STE LCO or under the other

applicable Technical Specification requirements. If it is

desired to perform the special operation under the

provisions of the STE LCO, the requirements of the STE LCO shall be followed.

LCO 3.0.8 LCO 3.0.8 establishes conditions under which systems are considered to remain capable of performing their intended

safety function when associated seismic-designated snubbers

are not capable of providing their associated support

function(s). This LCO states that the supported system is

not considered to be inoperable solely due to one or more

snubbers not capable of performing their associated support

function(s). This is appropriate because a limited length

of time is allowed for maintenance, testing, or repair of

one or more snubbers not capable of performing their

associated support function(s) and appropriate compensatory

measures are specified in the snubber requirements, which

are located outside of the Technical Specifications in the

Technical Requirements Manual (TRM). The snubber

requirements do not meet the criteria in 10 CFR

50.36(d)(2)(ii), and, as such, are appropriate for control

by the TRM.

If the allowed time expires and the snubber(s) are unable to

perform their associated support function(s), the affected

supported system's LCO must be declared not met and the

Conditions and Required Actions entered in accordance with

LCO 3.0.2.

LCO 3.0.8.a applies when one or more snubbers are not

capable of providing their associated support function(s) to a single train or subsystem of a multiple train or subsystem supported system or to a single train or subsystem of a

single train system. The supported system must not be

inoperable for any reason other than a lack of seismic

support. The LCO allows 72 hours8.333333e-4 days <br />0.02 hours <br />1.190476e-4 weeks <br />2.7396e-5 months <br /> to restore the snubber(s)

before declaring the supported system inoperable. The

72 hour8.333333e-4 days <br />0.02 hours <br />1.190476e-4 weeks <br />2.7396e-5 months <br /> Completion Time is reasonable based on the low

probability of a seismic event concurrent with an event that

would require operation of the supported system occurring LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-14 Revision 55 while the snubber(s) are not capable of performing their associated support function and due to the availability of

the redundant train of the supported system.

LCO 3.0.8.b applies when one or more snubbers are not

capable of providing their associated support function(s) to more than one train or subsystem of a multiple train or subsystem supported system. For example, if multiple

inoperable snubbers affect separate trains of a system or

one inoperable snubber affects multiple trains of a system, LCO 3.0.8.b is applicable. The supported system must not be

inoperable for any reason other than a lack of seismic

support. The LCO allows 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> to restore the snubber(s)

before declaring the supported system inoperable. The

12 hour1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> Completion Time is reasonable based on the low

probability of a seismic event concurrent with an event that

would require operation of the supported system occurring

while the snubber(s) are not capable of performing their

associated support function.

LCO 3.0.8 requires that risk be assessed and managed.

Industry and the Nuclear Regulatory Commission (NRC) guidance on the implementation of 10 CFR 50.65(a)(4) (the

Maintenance Rule) does not address seismic risk. However, use of LCO 3.0.8 must be considered with respect to other

plant maintenance activities, and integrated into the

existing Maintenance Rule process to the extent possible so

that maintenance of any unaffected train or subsystem is

properly controlled, and emergent issues are properly

addressed. The risk assessment need not be quantified, but

may be a qualitative awareness of the vulnerability of

systems and components when one or more snubbers are not

able to perform their associated support function.

The NRC placed several conditions on the use of LCO 3.0.8:

a. When LCO 3.0.8.a is used, one auxiliary feedwater (AFW) train not associated with the inoperable snubber must

be available.

b. When LCO 3.0.8.b is used, either one AFW train not associated with the inoperable snubber or some LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-15 Revision 55 alternative means of core cooling (e.g., once-through core cooling) must be available.

c. When the provisions of LCO 3.0.8 are used, confirm at least one train or subsystem of systems supported by the inoperable snubbers would remain capable of performing the systems required safety or support function(s) for postulated design loads other than seismic loads.

d. A record of the design function of the inoperable snubber (i.e., seismic versus non-seismic), the

implementation of any of these conditions, and the

associated plant configuration shall all be available

on a recoverable basis for NRC inspection.

LCO 3.0.9 LCO 3.0.9 establishes conditions under which systems described in the Technical Specifications are considered to

remain OPERABLE when required barriers are not capable of

providing their related support function(s).

Barriers are doors, walls, floor plugs, curbs, hatches, installed structures or components, or other devices, not

explicitly described in Technical Specifications, that

support the performance of the safety function of systems

described in the Technical Specifications. This LCO states

that the supported system is not considered to be inoperable

solely due to required barriers not capable of performing

their related support function(s) under the described

conditions. LCO 3.0.9 allows 30 days before declaring the

supported system(s) inoperable and the LCO(s) associated

with the supported system(s) not met. A maximum time is

placed on each use of this allowance to ensure that as required barriers are found or are otherwise made unavailable, they are restored. However, the allowable

duration may be less than the specified maximum time based

on the risk assessment.

If the allowed time expires and the barriers are unable to

perform their related support function(s), the supported

system's LCO(s) must be declared not met and the Conditions

and Required Actions entered in accordance with LCO 3.0.2.

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-16 Revision 55 This provision does not apply to barriers which support

ventilation systems or to fire barriers. The Technical

Specifications for ventilation systems provide specific

Conditions for inoperable barriers. Fire barriers are

addressed by other regulatory requirements and associated plant programs. This provision does not apply to barriers which are not required to support system OPERABILITY (see

NRC Regulatory Issue Summary 2001-09, "Control of Hazard

Barriers," dated April 2, 2001).

The provisions of LCO 3.0.9 are justified because of the low

risk associated with required barriers not being capable of

performing their related support function. This provision

is based on consideration of the following initiating event

categories:

• Loss of coolant accidents;

• High energy line breaks;

• Feedwater line breaks;

• Internal flooding;

• External flooding;

• Turbine missile ejection; and

• Tornado or high wind.

The risk impact of the barriers which cannot perform their

related support function(s) must be addressed pursuant to

the risk assessment and management provision of the

Maintenance Rule, 10 CFR 50.65(a)(4), and the associated

implementation guidance, Regulatory Guide 1.182, "Assessing

and Managing Risk Before Maintenance Activities at Nuclear

Power Plants." Regulatory Guide 1.182 endorses the guidance

in Section 11 of NUMARC 93-01, "Industry Guideline for

Monitoring the Effectiveness of Maintenance at Nuclear Power

Plants." This guidance provides for the consideration of

dynamic plant configuration issues, emergent conditions, and

other aspects pertinent to plant operation with the barriers

unable to perform their related support function(s). These

considerations may result in risk management and other

compensatory actions being required during the period that

barriers are unable to perform their related support

function(s).

LCO Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-17 Revision 55 LCO 3.0.9 may be applied to one or more trains or subsystems of a system supported by barriers that cannot provide their

related support function(s), provided that risk is assessed

and managed (including consideration of the effects on Large

Early Release and from external events). If applied

concurrently to more than one train or subsystem of a multiple train or subsystem supported system, the barriers supporting each of these trains or subsystems must provide

their related support function(s) for different categories

of initiating events. For example, LCO 3.0.9 may be applied

for up to 30 days for more than one train of a multiple

train supported system if the affected barrier for one train

protects against internal flooding and the affected barrier

for the other train protects against tornado missiles. In

this example, the affected barrier may be the same physical

barrier but serve different protection functions for each

train.

If during the time that LCO 3.0.9 is being used, the

required OPERABLE train or subsystem becomes inoperable, it

must be restored to OPERABLE status within 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br />.

Otherwise, the train(s) or subsystem(s) supported by

barriers that cannot perform their related support

function(s) must be declared inoperable and the associated

LCOs declared not met. This 24 hour2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> period provides time to

respond to emergent conditions that would otherwise likely

lead to entry into LCO 3.0.3 and a rapid plant shutdown, which is not justified given the low probability of an

initiating event which would require the barrier(s) not

capable of performing their related support function(s).

During this 24 hour2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> period, the plant risk associated with

the existing conditions is assessed and managed in

accordance with 10 CFR 50.65(a)(4).

SR Applicability B 3.0 B 3.0 SURVEILLANCE REQUIREMENT (SR) APPLICABILITY

BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-18 Revision 55 SRs Surveillance Requirement 3.0.1 through SR 3.0.4 establish the general requirements applicable to all Specifications and apply at all times, unless otherwise stated.

SR 3.0.1 Surveillance Requirement 3.0.1 establishes that SRs must be met during the MODEs or other specified conditions in the

Applicability for which the requirements of the LCO apply, unless otherwise specified in the individual SRs. This

Specification is to ensure that Surveillances are performed to verify the OPERABILITY of systems and components, and

that variables are within specified limits. Failure to meet

a SR within the specified Frequency, in accordance with

SR 3.0.2, constitutes a failure to meet an LCO.

Surveillances may be performed by means of any series of sequential, overlapping, or total steps provided the entire Surveillance is performed within the specified Frequency.

Additionally, the definitions related to instrument testing (e.g., CHANNEL CALIBRATION) specify that these tests are performed by means of any series of sequential, overlapping or total steps.

Systems and components are assumed to be OPERABLE when the associated SRs have been met. Nothing in this

Specification, however, is to be construed as implying that

systems or components are OPERABLE when: a. The systems or components are known to be inoperable, although still meeting the SRs; or b. The requirements of the Surveillance(s) are known to be not met between required Surveillance performances.

Surveillances do not have to be performed when the unit is in a MODE or other specified condition for which the

requirements of the associated LCO are not applicable, unless otherwise specified. The SRs associated with a STE

are only applicable when the STE is used as an allowable

exception to the requirements of a Specification.

Unplanned events may satisfy the requirements (including applicable acceptance criteria) for a given SR. In this

case, the unplanned event may be credited as fulfilling the

performance of the SR. This allowance includes those SRs SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-19 Revision 55 whose performance is normally precluded in a given MODE or other specified condition.

Surveillances, including Surveillances invoked by Required Actions, do not have to be performed on inoperable

equipment, because the ACTIONS define the applicable remedial measures that apply. Surveillances have to be met and performed in accordance with SR 3.0.2 prior to returning equipment to OPERABLE status.

Upon completion of maintenance, appropriate post-maintenance testing is required to declare equipment OPERABLE. This

includes ensuring applicable Surveillances are not failed and their most recent performance is in accordance with

SR 3.0.2. Post-maintenance testing may not be possible in

the current MODE or other specified conditions in the

Applicability due to the necessary unit parameters not

having been established. In these situations, the equipment

may be considered OPERABLE provided testing has been

satisfactorily completed to the extent possible and the

equipment is not otherwise believed to be incapable of

performing its function. This will allow operation to

proceed to a MODE or other specified condition where other

necessary post-maintenance tests can be completed. Some examples of this process are: a. Auxiliary feedwater pump turbine maintenance during refueling that requires testing at steam pressures

> 800 psi. However, if other appropriate testing is

satisfactorily completed, the Auxiliary Feedwater

System can be considered OPERABLE. This allows startup

and other necessary testing to proceed until the plant

reaches the steam pressure required to perform the

testing. b. High pressure safety injection maintenance during shutdown that requires system functional tests at a specified pressure. Provided other appropriate testing

is satisfactorily completed, startup can proceed with

high pressure safety injection considered OPERABLE.

This allows operation to reach the specified pressure to complete the necessary post-maintenance testing.

SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-20 Revision 55 SR 3.0.2 Surveillance Requirement 3.0.2 establishes the requirements for meeting the specified Frequency for Surveillances and any Required Action with a Completion Time that requires the

periodic performance of the Required Action on a "once per .

. ." interval.

Surveillance Requirement 3.0.2 permits a 25% extension of the interval specified in the Frequency. This extension

facilitates Surveillance scheduling and considers plant operating conditions that may not be suitable for conducting

the Surveillance (e.g., transient conditions or other ongoing Surveillance or maintenance activities).

The 25% extension does not significantly degrade the reliability that results from performing the Surveillance at its specified Frequency. This is based on the recognition

that the most probable result of any particular Surveillance being performed is the verification of conformance with the

SRs. The exceptions to SR 3.0.2 are those Surveillances for which the 25% extension of the interval specified in the

Frequency does not apply. These exceptions are stated in

the individual Specifications. An example of where SR 3.0.2

does not apply is the Containment Leakage Rate Testing

Program. The program establishes testing requirements and Frequencies in accordance with the requirements of regulations. The Technical Specifications cannot in and of themselves, extend a test interval specified in the regulations.

As stated in SR 3.0.2, the 25% extension also does not apply to the initial portion of a periodic Completion Time that

requires performance on a "once per . . ." basis. The 25%

extension applies to each performance after the initial

performance. The initial performance of the Required Action, whether it is a particular Surveillance or some other remedial action, is considered a single action with a single Completion Time. One reason for not allowing the 25%

extension to this Completion Time is that such an action

usually verifies that no loss of function has occurred by

checking the status of redundant or diverse components or

accomplishes the function of the inoperable equipment in an

alternative manner.

SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-21 Revision 55 The provisions of SR 3.0.2 are not intended to be used repeatedly, merely as an operational convenience to extend

Surveillance intervals (other than those consistent with refueling intervals) or periodic Completion Time intervals beyond those specified.

SR 3.0.3 Surveillance Requirement 3.0.3 establishes the flexibility to defer declaring affected equipment inoperable or an

affected variable outside the specified limits when a

Surveillance has not been completed within the specified Frequency. A delay period of up to 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> or up to the

limit of the specified Frequency, whichever is greater, applies from the point in time that it is discovered that the Surveillance has not been performed in accordance with SR 3.0.2, and not at the time that the specified Frequency

was not met.

This delay period provides an adequate time to complete Surveillances that have been missed. This delay period permits the completion of a Surveillance before complying with Required Actions or other remedial measures that might

preclude completion of the Surveillance.

The basis for this delay period includes consideration of unit conditions, adequate planning, availability of

personnel, the time required to perform the Surveillance, the safety significance of the delay in completing the

required Surveillance, and the recognition that the most probable result of any particular Surveillance being performed is the verification of conformance with the

requirements.

When a Surveillance with a Frequency based not on time intervals, but upon specified unit conditions, operating situations, or requirements of regulations (e.g., prior to entering MODE 1 after each fuel loading, or in accordance

with 10 CFR Part 50, Appendix J, as modified by approved

exemptions, etc.) is discovered to not have been performed

when specified, SR 3.0.3 allows for the full delay period of

up to the specified Frequency to perform the Surveillance.

However, since there is not a time interval specified, the

missed Surveillance should be performed at the first

reasonable opportunity.

SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-22 Revision 55 Surveillance Requirement 3.0.3 provides a time limit for, and allowances for the performance of, Surveillances that

become applicable as a consequence of MODE changes imposed

by Required Actions.

Failure to comply with specified Frequencies for SRs is expected to be an infrequent occurrence. Use of the delay

period established by SR 3.0.3 is a flexibility that is not

intended to be used as an operational convenience to extend

Surveillance intervals. While up to 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> or the limit of the specified Frequency is provided to perform the missed

Surveillance, it is expected that the missed Surveillance

will be performed at the first reasonable opportunity. The

determination of the first reasonable opportunity should

include consideration of the impact on plant risk (from

delaying the Surveillance, as well as any plant

configuration changes required or shutting the plant down to

perform the Surveillance) and impact on any analysis

assumptions, in addition to unit conditions, planning, availability of personnel, and the time required to perform

the Surveillance. This risk impact should be managed

through the program in place to implement 10 CFR 50.65(a)(4)

and its implementation guidance, NRC Regulatory Guide 1.182, "Assessing and Managing Risk Before Maintenance Activities

at Nuclear Power Plants." This Regulatory Guide addresses

consideration of temporary and aggregate risk impacts, determination of risk management action thresholds, and risk

management action up to and including plant shutdown. The

missed Surveillance should be treated as an emergent

condition as discussed in the Regulatory Guide. The risk

evaluation may use quantitative, qualitative, or blended

methods. The degree of depth and rigor of the evaluation

should be commensurate with the importance of the component.

Missed Surveillances for important components should be analyzed quantitatively. If the results of the risk

evaluation determine the risk increase is significant, this

evaluation should be used to determine the safest course of

action. All missed Surveillances will be placed in the

licensee's Corrective Action Program.

If a Surveillance is not completed within the allowed delay period, then the equipment is considered inoperable or the SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-23 Revision 55 variable is considered outside the specified limits, and the Completion Times of the Required Actions for the applicable

LCO Conditions begin immediately upon expiration of the

delay period. If a Surveillance is failed within the delay period, then the equipment is inoperable or the variable is outside the specified limits, and the Completion Times of the Required Actions for the applicable LCO Conditions begin immediately upon the failure of the Surveillance.

Completion of the Surveillance within the delay period allowed by this Specification, or within the Completion Time of the ACTIONS, restores compliance with SR 3.0.1.

SR 3.0.4 Surveillance Requirement 3.0.4 establishes the requirement that all applicable SRs must be met before entry into a MODE

or other specified Condition in the Applicability.

This Specification ensures system and component OPERABILITY requirements and variable limits are met before entry into

MODEs or other specified conditions in the Applicability for

which these systems and components ensure safe operation of

the unit. The provisions of this Specification should not

be interpreted as endorsing the failure to exercise the good

practice of restoring systems or components to OPERABLE

status before entering an associated MODE or other specified

condition in the Applicability.

A provision is included to allow entry into a MODE or other

specified condition in the Applicability when an LCO is not

met due to Surveillance not being met in accordance with LCO 3.0.4.

However, in certain circumstances, failing to meet an SR will not result in SR 3.0.4 restricting a MODE change or

other specified condition change. When a system, subsystem, division, component, device, or variable is inoperable or

outside its specified limits, the associated SR(s) are not

required to be performed, per SR 3.0.1, which states that

Surveillances do not have to be performed on inoperable

equipment. When equipment is inoperable, SR 3.0.4 does not

apply to the associated SR(s) since the requirement for the

SR(s) to be performed is removed. Therefore, failing to

perform the Surveillance(s) within the specified Frequency SR Applicability B 3.0 BASES CALVERT CLIFFS - UNITS 1 & 2 B 3.0-24 Revision 55 does not result in an SR 3.0.4 restriction to changing MODES or other specified conditions of the Applicability.

However, since the LCO is not met in this instance, LCO 3.0.4 will govern any restrictions that may (or may not)

apply to MODE or other specified condition changes.

Surveillance Requirement 3.0.4 does not restrict changing MODES or other specified conditions of the Applicability when a Surveillance has not been performed within the

specified Frequency, provided the requirement to declare the

LCO not met has been delayed in accordance with SR 3.0.3.

The provisions of SR 3.0.4 shall not prevent entry into MODES or other specified conditions in the Applicability

that are required to comply with ACTIONS. In addition, the

provisions of SR 3.0.4 shall not prevent changes in MODES or

other specified conditions in the Applicability that result

from any unit shutdown. In this context, a unit shutdown is

defined as a change in MODE or other specified condition in

the Applicability associated with transitioning from MODE 1

to MODE 2, MODE 2 to MODE 3, MODE 3 to MODE 4, and MODE 4 to

MODE 5.

The precise requirements for performance of SRs are specified such that exceptions to SR 3.0.4 are not

necessary. The specific time frames and conditions

necessary for meeting the SRs are specified in the

Frequency, in the Surveillance, or both. This allows

performance of Surveillances when the prerequisite

condition(s) specified in a Surveillance procedure require

entry into the MODE or other specified condition in the

Applicability of the associated LCO prior to the performance

or completion of a Surveillance. A Surveillance that could

not be performed until after entering the LCOs

Applicability, would have its Frequency specified such that it is not "due" until the specific conditions needed are met. Alternately, the Surveillance may be stated in the

form of a Note, as not required (to be met or performed)

until a particular event, condition, or time has been

reached. Further discussion of the specific formats of SRs'

annotation is found in Section 1.4, Frequency.