ML22316A003

From kanterella
Jump to navigation Jump to search
Core Operating Limits Report (Colr), Cycle 30, Pattern Aod, Revision 1
ML22316A003
Person / Time
Site: North Anna Dominion icon.png
Issue date: 11/09/2022
From: Standley B
Virginia Electric & Power Co (VEPCO)
To:
Office of Nuclear Reactor Regulation, Document Control Desk
References
22-344
Download: ML22316A003 (1)
v • d • e


Text

VIRGINIA ELECTRIC AND POWER COMPANY RICHMOND, VIRGINIA 23261

November 9, 2022

U. S. Nuclear Regulatory Commission Serial No.: 22-344 Attention: Document Control Desk NRA/ENC: RO Washington, DC 20555 Docket Nos.: 50-338 License Nos.: NPF-4

VIRGINIA ELECTRIC AND POWER COMPANY (DOMINION ENERGY VIRGINIA)

NORTH ANNA POWER STATION UNIT 1 CORE OPERATING LIMITS REPORT NORTH ANNA UNIT 1, CYCLE 30, PATTERN AOD, REVISION 1 The North Anna Power Station Unit 1 Core Operating Limits Report (COLR) has been revised to reflect the reload design evaluations supporting Cycle 30 as a result of reload pattern re-design. Therefore, pursuant to Technical Specification 5.6.5.d, attached is a copy of the COLR for North Anna Unit 1, Cycle 30, Pattern AOD, Revision 1.

If you have any questions or require additional information, please contact Yan Gao at (804) 273-2768.

Sincerely,

B. E. Standley, Director Nuclear Regulatory Affairs Dominion Energy Services, Inc. for Virginia Electric and Power Company

Attachment:

COLR-N1 C30, Revision 1, Core Operating Limits Report

Commitments: None.

Serial No.: 22-344 Docket No.: 50-338 Page 2 of 2

cc: U. S. Nuclear Regulatory Commission, Region II Marquis One Tower 245 Peachtree Center Avenue, NE, Suite 1200 Atlanta, Georgia 30303-1257

Mr. G. E. Miller NRC Senior Project Manager - North Anna Power Station U. S. Nuclear Regulatory Commission One White Flint North Mail Stop 09 E-3 11555 Rockville Pike Rockville, Maryland 20852-2738

NRC Senior Resident Inspector North Anna Power Station Serial No.: 22-344 Docket No.: 50-338

ATTACHMENT

COLR-N1 C30, Revision 1

Core Operating Limits Report

NORTH ANNA POWER STATION UNIT 1 VIRGINIA ELECTRIC AND POWER COMPANY (DOMINION ENERGY VIRGINIA)

Serial No.: 22-344 Docket No.: 50-338 Attachment Page 1 of 18

N1C30 CORE OPERATING LIMITS REPORT

INTRODUCTION

The Core Operating Limits Report (COLR) for North Anna Unit 1 Cycle 30 has been prepared in accordance with North Anna Technical Specification 5.6.5. The technical specifications affected by this report are listed below:

TS 2.1.1 Reactor Core Safety Limits TS 3.1.1 Shutdown Margin (SDM)

TS 3.1.3 Moderator Temperature Coefficient (MTC)

TS 3.1.4 Rod Group Alignment Limits TS 3.1.5 Shutdown Bank Insertion Limit TS 3.1.6 Control Bank Insertion Limits TS 3.1.9 PHYSICS TESTS Exceptions - Mode 2 TS 3.2.1 Heat Flux Hot Channel Factor TS 3.2.2 Nuclear Enthalpy Rise Hot Channel Factor (FN Lrn)

TS 3.2.3 Axial Flux Difference (AFD)

TS 3.3.1 Reactor Trip System (R TS) Instrumentation TS 3.4.l RCS Pressure, Temperature, and Flow DNB Limits TS 3.5.6 Boron Injection Tank (BIT)

TS 3.9.l Boron Concentration

In addition, a technical requirement (TR) in the NAPS Technical Requirements Manual (TRM) refers to the COLR:

TR 3.1.1 Boration Flow Paths - Operating

The analytical methods used to determine the core operating limits are those previously approved by the NRC and discussed in the documents listed in the References Section.

Cycle-specific values are presented in bold. Text in italics is provided for information only.

COLR-NIC30, Revision 1

EV AL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 2 of 18

REFERENCES

1. VEP-FRD-42-A, Revision 2, Minor Revision 2, "Reload Nuclear Design Methodology,"

October 2017.

Methodology for:

TS 3.1.1-Shutdown Margin TS 3.1.3 - Moderator Temperature Coefficient TS 3.1.4 - Rod Group Alignment Limits TS 3.1.5 - Shutdown Bank Insertion Limit TS 3.1.6-Control Bank Insertion Limits TS 3.1.9-Physics Tests Exceptions-Mode 2 TS 3.2.1 - Heat Flux Hot Channel Factor TS 3.2.2 - Nuclear Enthalpy Rise Hot Channel Factor TS 3.5.6 - Boron Injection Tank (BIT) and TS 3.9.1-Boron Concentration

2. WCAP-16996-P-A, Rev. 1, "Realistic LOCA Evaluation Methodology Applied to the Full Spectrum of Break Sizes (FULL SPECTRUM LOCA Methodology)," November 2016.

Methodology for: TS 3.2.1 - Heat Flux Hot Channel Factor

3. EMF-2328(P)(A), "PWR Small Break LOCA Evaluation Model, S-RELAP5 Based," as supplemented by ANP-3467P, Revision 0, North Anna Fuel-Vendor Independent Small Break LOCA Analysis," as approved by NRC Safety Evaluation Report dated March 19, 2021.

Methodology for: TS 3.2.1 - Heat Flux Hot Channel Factor

4. WCAP-12610-P-A, "VANTAGE+ FUEL ASSEMBLY - REFERENCE CORE REPORT,"

April 1995.

Methodology for:

TS 2.1.1 - Reactor Core Safety Limits TS 3.2.1 - Heat Flux Hot Channel Factor

5. VEP-NE-2-A, Revision 0, "Statistical DNBREvaluation Methodology," June 1987.

Methodology for:

TS 3.2.2-Nuclear Enthalpy Rise Hot Channel Factor and TS 3.4.1 - RCS Pressure, Temperature and Flow DNB Limits

COLR-Nl C30, Revision 1

EVAL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 3 of 18

6. VEP-NE-1-A, Revision 0, Minor Revision 3, "Relaxed Power Distribution Control Methodology and Associated FQ Surveillance Technical Specifications," October 2017.

Methodology for:

TS 3.2.1 - Heat Flux Hot Channel Factor and TS 3.2.3 - Axial Flux Difference

7. WCAP-8745-P-A, "Design Bases for the Thermal Overpower AT and Thermal Overtemperature AT Trip Functions," September 1986.

Methodology for:

TS 2.1.1 - Reactor Core Safety Limits and TS 3.3.1 - Reactor Trip System Instrumentation

8. WCAP-14483-A, "Generic Methodology for Expanded Core Operating Limits Report," January 1999.

Methodology for:

TS 2.1.1 - Reactor Core Safety Limits TS 3.1.1 - Shutdown Margin TS 3.1.4 - Rod Group Alignment Limits TS 3.1.9 - Physics Tests Exceptions - Mode 2 TS 3.3.1-Reactor Trip System Instrumentation TS 3.4.1 - RCS Pressure, Temperature, and Flow DNB Limits TS 3.5.6-Boron Injection Tank (BIT) and TS 3.9.1 - Boron Concentration

9. DOM-NAF-2-P-A, Revision 0, Minor Revision 3, "Reactor Core Thermal-Hydraulics Using the VIPRE-D Computer Code," including Appendix C, "Qualification of the Westinghouse WRB-2M CHF Correlation in the Dominion VIPRE-D Computer Code," August 2010 and Appendix D, "Qualification of the ABB-NV and WLOP CHF Correlations in the Dominion VIPRE-D Computer Code," September 2014.

Methodology for:

TS 3.2.2-Nuclear Enthalpy Rise Hot Channel Factor and TS 3.4.1-RCS Pressure, Temperature and Flow DNB Limits

10. WCAP-12610-P-A and CENPD-404-P-A, Addendum 1-A, "Optimized ZIRLO'," July 2006.

Methodology for:

TS 2.1.1 - Reactor Core Safety Limits and TS 3.2.1-Heat Flux Hot Channel Factor

COLR-Nl C30, Revision 1

EVAL-ENG-RSE-NIC30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 4 of 18 2.0 SAFETY LIMITS (SLs)

2.1 SLs

2.1.1 Reactor Core SLs

In MODES 1 and 2, the combination of THERMAL POWER, Reactor Coolant System (RCS) highest loop average temperature, and pressurizer pressure shall not exceed the limits specified in COLR Figure 2.1-1; and the following SLs shall not be exceeded.

2.1.1.1 The departure from nucleate boiling ratio (DNBR) shall be maintained greater than or equal to the 95/95 DNBR criterion for the DNB correlations and methodologies specified in the References Section.

COLR-NlC30, Revision 1

EV AL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 5 of 18 COLR Figure 2.1-1

NORTH ANNA REACTOR CORE SAFETY LIMITS 665 660 ~~

655 ~

"""""llli, 650 ~ ~.._

~ ~ ~ psia 645 ~ -- "~

~ r---......

640 ~ ~ psia...

'u:' 635,,.,____

f.., ~,~ "

l!! 630 """'........

.... ::s.... """'--

ra 625 ~" ~"h "

cu ~..........._,

a. ~ -....., ~ 2000 psia ~ ~\\

{!!. E 620 cu 615 ~ \\' r---..... r\\

bl>

ra ".... ~........... ~ \\ \\

... ~ 1860 psia cu 610

< > ~, ~ '--

cu 605..... "'

Ill.......

Ill

~ 600 ~ -,

595....... \\~ "' \\

590 ""' ~ \\

585 ~i\\.'

580 \\ '

575

570 0 10 20 30 40 so 60 70 80 90 100 110 120

Percent of RATED THERMAL POWER

COLR-Nl C30, Revision 1

EVAL-ENG-RSE-NIC30, Revision I, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 6 of 18 3.1 REACTIVITY CONTROL SYSTEMS

3.1.1 SHUTDOWN MARGIN (SDM)

LCO 3.1.1 SDM shall be~ 1.77 % Ak/k.

3.1.3 Moderator Temperature Coefficient (MTC)

LCO 3.1.3 The MTC shall be maintained within the limits specified below. The upper limit ofMTC is +0.6 x 10-4 Ak/k/°F, when< 70% RTP, and 0.0 Ak/k/°F when~ 70%

RTP.

The BOC/ ARO-MTC shall be~ +0.6 x 10-4 Ak/k/°F (upper limit), when< 70%

RTP, and~ 0.0 Ak/k/°F when~ 70% RTP.

The EOC/ ARO/RTP-MTC shall be less negative than -5.0 x 10-4 Ak/k/°F (lower limit).

The MTC surveillance limits are:

The 300 ppm/ARO/RTP-MTC should be less negative than or equal to

-4.0 x 10-4 Ak/k/°F [Note l].

The 60 ppm/ARO/RTP-MTC should be less negative than or equal to

-4. 7 x 10 4 Ak/k/°F [Note 2].

SR 3.1.3.2 Verify MTC is within -5.0 x 10-4 Ak/k/°F (lower limit).

Note 1: If the MTC is more negative than -4.0 x 10-4 Ak/k/°F, SR 3.1.3.2 shall be repeated once per 14 EFPD during the remainder of the fuel cycle.

Note 2: SR 3.1.3.2 need not be repeated if the MTC measured at the equivalent of equilibrium RTP-ARO boron concentration of~ 60 ppm is less negative than -4. 7 x 1 o-4 Ak/k/°F.

COLR-Nl C30, Revision 1

EV AL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 7 of 18 3.1.4 Rod Group Alignment Limits

Required Action A.1.1 Verify SDM to be~ 1.77 % Ak/k.

Required Action B.1.1 Verify SDM to be~ 1.77 % Ak/k.

Required Action D.1.1 Verify SDM to be~ 1.77 % Ak/k.

3.1.5 Shutdown Bank Insertion Limits LCO 3.1.5 Each shutdown bank shall be withdrawn to at least 225 steps.

Required Action A.1.1 Verify SD M to be ~ 1. 77 % Ak/k.

Required Action B.1 Verify SDM to be~ 1.77 % Ak/k.

SR 3.1.5.1 Verify each shutdown bank is withdrawn to at least 225 steps.

3.1.6 Control Bank Insertion Limits LCO 3.1.6 Control banks shall be limited in physical insertion as shown in COLR Figure 3.1-

1. Sequence of withdrawal shall be A, B, C and D, in that order; and the overlap limit during withdrawal shall be 97 steps.

Required Action A.1.1 Verify SDM to be~ 1.77 % Ak/k.

Required Action B.l.1 Verify SDM to be~ 1.77 % Ak/k.

Required Action C.l Verify SDM to be~ 1.77 % Ak/k.

SR 3.1.6.1 Verify estimated critical control bank position is within the insertion limits specified in COLR Figure 3.1-1.

SR 3.1.6.2 Verify each control bank is within the insertion limits specified in COLR Figure 3.1-1.

SR 3.1.6.3 Verify each control bank not fully withdrawn from the core is within the sequence and overlap limits specified in LCO 3.1.6 above.

3.1.9 PHYSICS TESTS Exceptions - MODE 2 LCO 3.1.9.b SDM is ~ 1. 77 % Ak/k.

SR 3.1.9.4 Verify SDM to be~ 1.77 % Ak/k.

COLR-NIC30, Revision 1

EV AL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 8 of 18 COLR Figure 3.1-1 North Anna 1 Cycle 30 Control Rod Bank Insertion Limits Fully w/d position= 225 steps 230 I 220 / 0.524, 225 210 /

200 I/

/ 1.0, 194,#

190 180 I/ /

170 / C-BANK ~ V

160 / /

-c 150 / )7

~ / /

t; g-140

  1. / J7

~ 130 0 /

~ 120.l{:18 0 Av

~110

J lf; 100 0 /

-c /o-BAr IK a: 0 90 Al

80 /

70 A/

60 /

so A/

40 /

30 V

20 /

10 V 0 /o.048,o I

0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1

Fraction of Rated Thermal Power

COLR-Nl C30, Revision I

EVAL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 9 of18 3.2 POWER DISTRIBUTION LIMITS

3.2.1 Heat Flux Hot Channel Factor (Fo(Z))

LCO 3.2.1 Fo(Z), as approximated by FoE(Z) and FoT(Z), shall be within the limits specified below.

CFQ=2.32

The Heat Flux Hot Channel Factor, Fo(Z), shall be limited by the following relationships:

for P > 0.5

FQ(Z) :::;; 0.5 for P:::;; 0.5 CFQ

  • K(Z)

where: THERMAL POWER p = RATED THERMAL POWER ; and

K(Z) is provided in COLR Figure 3.2-1

FoE(Z) is an excellent approximation for F o(Z) when the reactor is at the steady-state power.

Fo(Z) from the incore flux map results is increased by 1.03 for fuel manufacturing tolerances and 1.05 for measurement uncertainty to obtain FoE(Z).

F3(Z) = FQ(Z) * (1.03) * (1.05)

The expression for FoT(Z) is:

FJ(Z) = F3(Z)

  • N(Z) where:

N Z = F Q (Z),Maximum Condition I

( ) F Q (Z),Equilibrium Condition I

The discussion in the Bases Section B 3.2.1 for this LCO requires the application of a cycle dependent non-equilibrium multiplier, N (Z), to the steady state Fl (Z). N (Z) values are calculated for each flux map using analytically derived F Q(Z) values (scaled by relative power), consistent with the methodology described in VEP-NE-1. N(Z) accounts for power distribution transients encountered during normal operation.

COLR-Nl C30, Revision 1

EV AL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 10 of 18

The cycle-specific penalty factors are presented in COLR Table 3.2-1.

Also discussed is the application of the appropriate factor to account for potential increases in F Q(Z) between surveillances. This factor is determined on a cycle specific basis and is dependent on the predicted increases in steady-state and transient F Q(Z)/K(Z) versus burnup. A minimum value of 2% is used should any increase in steady-state or transient measured or predicted peaking factor be determined unless frequent flux mapping is invoked (7 EFPD).

The required operating space reductions are included in COLR Table 3.2-2.

Should F QT (Z) exceed its limits the normal operating space should be reduced to gain peaking factor margins. The determination and verification of the margin improvements along with the corresponding required reductions in the Thermal Power Limit and AFD Bands are performed on a cycle-specific basis.

COLR-Nl C30, Revision 1

EV AL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 11 of 18

COLR Table 3.2-1 N1C30 Penalty Factors for Flux Map Analysis Burnup Penalty (MWD/MTU) Factor%

0-499 2.0 500 - 999 4.5 1000 - 1999 3.5 2000-2999 2.0 3000 - 3999 2.0 4000 - 4999 2.0 5000 - 6999 2.0 7000 - 8999 2.0 9000 - 10999 2.0 11000 - 12999 2.0 13000 - 14999 2.0 15000 - 16999 2.0 17000 - 18999 2.0 19000-EOC 2.0 Notes:

1. Penalty Factors are not required for initial power ascension flux maps.
2. All full power maps shall apply a Penalty Factor unless frequent flux mapping is invoked

(~ 7 EFPD).

COLR Table 3.2-2 N1C30 Required Operating Space Reductions for FaT(Z) Exceeding its Limits Required FQT(Z) Required Negative AFD Band Positive AFD Band Margin THERMAL POWER Reduction from AFD Reduction from AFD Improvement Limit (% RTP) Limits* (% AFD) Limits* (% AFD)

>0%and::S 1% ::S98.0% 2'.:0.5% 2'.:1.0%

> 1%and::S2% ::S96.0% ~1.0% 2'.:2.5%

>2% and::S3% ::S95.0% 2'.: 1.5% 2'.: 3.5%

>3% ::S50% NIA NIA

  • Axial Flux Difference Limits are provided in COLR Figure 3.2-2

COLR-Nl C30, Revision 1

EVAL-ENG-RSE-N1C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 12 of 18 COLR Figure 3.2-1

K(Z) - Normalized FQ as a Function of Core Height 1.2

1.1

6, 1.0 1.0

r-- r-- r-- ~

0.9 (12.925)

0.8 g

5! 0.7 C

w

~

...I

<C 0.6

~

0 z

..!.. 0.5

~

0.4

0.3

0.2

0.1

0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 CORE HEIGHT (FT)

COLR-Nl C30, Revision 1

EVAL-ENG-RSE-N1C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 13 of 18 3.2.2 Nuclear Enthalpy Rise Hot Channel Factor (FNAH)

LCO 3.2.2 pNAH shall be within the limits specified below.

FNMI :5: 1.587{1 + 0.3(1-P)}

THERMAL POWER where: p = RATED THERMAL POWER

SR 3.2.2.1 Verify FNAH is within limits specified above.

3.2.3 AXIAL FLUX DIFFERENCE (AFD)

LCO 3.2.3 The AFD in% flux difference units shall be maintained within the limits specified in COLR Figure 3.2-2.

COLR-N1C30, Revision 1

EVAL-ENG-RSE-N1C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 14 of 18 COLR Figure 3.2-2 North Anna 1 Cycle 30 Axial Flux Difference Limits

120

110

100 100) 10v \\6, 90 r2*

Unacceptable / Unacceptable Operation I\\ Operation 80 '

I.,

a, V

~ 70 j Acceptable Operation 'I\\ \\

a. 0 ni E I

I., 60 a, I

.c I-

"C a, / \\

ca 50 (+20, 50)

- (-2 7, 50) 0:::

't-0 40

-C a,

~

a,

a. 30

20

10

0

-30 -20 -10 0 10 20 30 Percent Flux Difference (Delta-I)

COLR-Nl C30, Revision 1

EV AL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 15 of 18 3.3 INSTRUMENTATION

3.3.1 Reactor Trip System (RTS) Instrumentation

TS Table 3.3.1-1 Note 1: Overtemperature ~T

The Overtemperature ~ T Function Allowable Value shall not exceed the following nominal trip setpoint by more than 2% of ~T span, with the numerical values of the parameters as specified below.

where: ~T is measured RCS ~ T, °F

~To is the indicated ~ T at RTP, °F s is the Laplace transform operator, sec-1 T is the measured RCS average temperature, °F T' is the nominal T avg at RTP, ~ 586.8 °F p is the measured pressurizer pressure, psig P' is the nominal RCS operating pressure, ~ 2235 psig

K1 ~ 1.2715 K3 ~ 0.001145 /psig

't1, 't2 = time constants utilized in the lead-lag controller for Tavg

't1 ~ 23.75 sec 't2 ~ 4.4 sec

(1 +'t1S)/(l +'t2S) = function generated by the lead-lag controller for Tavg dynamic compensation

ft (Af) ~ 0.0291 {-13.0 - ( qt - qb)} when (qt-qb) <-13.0% RTP 0 when -13.0% RTP ~ (qt - qb) ~ +7.0% RTP 0.0251{(q1-qb)- 7.0} when (qt - qb) > +7.0% RTP

Where qt and qb are percent RTP in the upper and lower halves of the core, respectively, and q1 + qb is the total THERMAL POWER in percent RTP.

COLR-Nl C30, Revision I

EVAL-ENG-RSE-N1C30, Revision I, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 16 of 18 TS Table 3.3.1-1 Note 2: Overpower L\\.T

The Overpower LiT Function Allowable Value shall not exceed the following nominal trip setpoint by more than 2% of LiT span, with the numerical values of the parameters as specified below.

where: LiT is measured RCS AT, °F.

LiTo is the indicated AT at RTP, °F.

s is the Laplace transform operator, sec-1*

T is the measured RCS average temperature, °F.

T' is the nominal T avg at RTP, ~ 586.8 °F.

K4 ~ 1.0865 Ks ~ 0.0198 /°F for increasing Tavg K6 ~ 0.00162 /°F when T > T' 0 /°F for decreasing T avg 0 /°F when T ~ T'

T3 = time constant utilized in the rate lag controller for Tavg T3 ~ 9.5 sec

  • ns I (1 + T3s) = function generated by the rate lag controller for T avg dynamic compensation

fa(Af) = O, for all M.

COLR-N1C30, Revision 1

EVAL-ENG-RSE-NIC30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 17 of 18

3.4 REACTOR COOLANT SYSTEM (RCS)

3.4.1 RCS Pressure, Temperature, and Flow Departure from Nucleate Boiling (DNB) Limits

LCO 3.4.1 RCS DNB parameters for pressurizer pressure, RCS average temperature, and RCS total flow rate shall be within the limits specified below:

a. Pressurizer pressure is greater than or equal to 2205 psig;
b. RCS average temperature is less than or equal to 591 °F; and
c. RCS total flow rate is greater than or equal to 295,000 gpm.

SR 3.4.1.1 Verify pressurizer pressure is greater than or equal to 2205 psig.

SR 3.4.1.2 Verify RCS average temperature is less than or equal to 591 °F.

SR 3.4.1.3 Verify RCS total flow rate is greater than or equal to 295,000 gpm.

SR 3.4.1.4 ------------------------------NOTE--------------------------------------------

Not required to be performed until 30 days after~ 90% RTP.

Verify by precision heat balance that RCS total flow rate is ~ 295,000 gpm.

3.5 EMERGENCY CORE COOLING SYSTEMS (ECCS)

3.5.6 Boron Injection Tank (BIT)

Required Action B.2 Borate to a SDM ~ 1.77 % Ak/k at 200 °F.

3.9 REFUELING OPERATIONS

3.9.1 Boron Concentration

LCO 3.9.1 Boron concentrations of the Reactor Coolant System (RCS), the refueling canal, and the refueling cavity shall be maintained~ 2600 ppm.

SR 3.9.1.1 Verify boron concentration is within the limit specified above.

COLR-Nl C30, Revision 1

EV AL-ENG-RSE-Nl C30, Revision 1, Attachment A Serial No.: 22-344 Docket No.: 50-338 Attachment Page 18 of 18

NAPS TECHNICAL REQUIREMENTS MANUAL

TRM 3.1 REACTIVITY CONTROL SYSTEMS TR 3.1.1 Boration Flow Paths -Operating Required Action D.2 Borate to a SHUTDOWN MARGIN 1.77 % Ak/k at 200 °F, after xenon decay.

COLR-Nl C30, Revision I

EVAL-ENG-RSE-NIC30, Revision 1, Attachment A

Retrieved from "https://kanterella.com/w/index.php?title=ML22316A003&oldid=3717736"