ML22172A187

CoC 9358.R7

ML22172A187
Person / Time
Site:	07109358
Issue date:	06/23/2022
From:	William Allen Storage and Transportation Licensing Branch
To:	TN Americas LLC
PSAVEROT NMSS/DFM/STLB 3014157505
Shared Package
ML22172A184	List: ML22172A185 ML22172A187
References
EPID A33010
Download: ML22172A187 (37)

Text

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 1

OF 36 2.

PREAMBLE

a. This certificate is issued to certify that the package (packaging and contents) described in Item 5 below meets the applicable safety standards set forth in Title 10, Code of Federal Regulations, Part 71, Packaging and Transportation of Radioactive Material.

This certificate does not relieve the consignor from compliance with any requirement of the regulations of the U.S. Department of Transportation or

b. other applicable regulatory agencies, including the government of any country through or into which the package will be transported.

3.

THIS CERTIFICATE IS ISSUED ON THE BASIS OF A SAFETY ANALYSIS REPORT OF THE PACKAGE DESIGN OR APPLICATION a.

ISSUED TO (Name and Address)

b. TITLE AND IDENTIFICATION OF REPORT OR APPLICATION TN Americas LLC 7160 Riverwood Drive, Suite 200 Columbia, MD 21046 TN-LC Transportation Package Safety Analysis Report, Revision No. 10, dated April 2022.

4. CONDITIONS This certificate is conditional upon fulfilling the requirements of 10 CFR Part 71, as applicable, and the conditions specified below.

5.

(a)

Packaging (1)

Model No.: TN-LC (2)

Description The packaging, designed for transport of irradiated test, research, and commercial reactor fuel in either a closed transport vehicle or an ISO container, consists of a payload basket, a shielded body, a shielded closure lid and top and bottom impact limiters. The packaging body is a right circular cylinder, approximately 197.5 inches long and 30 inches in diameter, composed of top and bottom end flange forgings connected by inner and outer shells. Lead shielding, made of ASTM B29 copper lead, is placed between the two cylindrical shells, in the bottom end assembly, and in the lid. Neutron shielding, composed of a borated resin compound inserted into twenty aluminum shield boxes, is set between the outer shell and a 0.25 inch-thick Type 304 stainless steel outer sheet. Two removable trunnions are bolted to the packaging body using eight 1-8UNC bolts for each trunnion. Two pocket trunnions in the bottom flange, used for rotating the package, may also be used for horizontal package lifting.

Impact limiters, with an approximate outside diameter of 66 inches and height of 22.75 inches, consisting of balsa and redwood blocks encased in stainless steel shells, are attached to each end of the packaging during shipment, each with eight 1-8UNC bolts.

Four basket designs are provided for transport of Boiling Water Reactor (BWR), Pressurized Water Reactor (PWR), Mixed Oxide Fuel (MOX), Evolutionary Pressurized Reactor (EPR),

National Research Universal Reactor (NRU), National Research Experimental

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 2

OF 36 5.(a)(2) Description (Continued)

Reactor (NRX), Material Test Reactor (MTR), and Training, Research, and Isotope General Atomics Reactor (TRIGA) fuel assemblies, fuel elements or fuel rods. The packaging may be loaded or unloaded either in a pool or a hot cell environment. The spent fuel payload is shipped dry in a helium atmosphere. The first fabricated packaging, Unit 1, shall only be loaded with the TN-LC 1FA basket.

Nominal weights and dimensions are as follows:

Overall length with impact limiters:

230 inches Overall length without impact limiters:

197.50 inches Cavity length (minimum):

182.50 inches 182.10 inches for Unit 1 Cavity inner diameter:

18 inches Lid thickness:

7.50 inches Weight of contents:

7,100 lbs Weight of lid:

1,000 lbs Weight of impact limiters:

3,000 lbs Total loaded weight of the package:

51,000 lbs (3)

Drawings The packaging is constructed and assembled in accordance with the following drawings:

65200-71-01 Revision 10 TN-LC Cask Assembly (11 sheets) 65200-71-20 Revision 5 TN-LC Impact Limiter Assembly (2 sheets) 65200-71-21 Revision 2 TN-LC Transport Packaging Transport Configuration (1 sheet) 65200-71-40 Revision 4 TN-LC-NRUX Basket Basket Assembly (5 sheets) 65200-71-50 Revision 4 TN-LC-NRUX Basket Basket Tube Assembly (5 sheets)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 3

OF 36 65200-71-60 Revision 4 TN-LC-MTR Basket General Assembly (4 sheets) 65200-71-70 Revision 4 TN-LC-MTR Basket Fuel Bucket (2 sheets) 65200-71-80 Revision 4 TN-LC-TRIGA Basket (5 sheets) 65200-71-90 Revision 7 TN-LC-1FA Basket (5 sheets) 65200-71-96 Revision 5 TN-LC-1FA BWR Sleeve and Hold-Down Ring (2 sheets) 65200-71-102 Revision 7 65200-71-91 Revision 0 TN-LC-1FA Pin Can Basket (5 sheets)

TN-LC-1FA PWR Basket Damaged Fuel Assembly Can (3 Sheets) 5.(b)

Contents (1)

Type and Form of Material (i)

Intact or damaged NRU and NRX Mk I fuel assemblies which meet the specifications listed in Table 1 below, respectively, are authorized for transportation in the TN-LC-NRUX basket.

Intact fuel assemblies are fuel assemblies containing fuel rods with no known or suspected cladding defects greater than hairline cracks or pinhole leaks.

Damaged fuel assemblies, with cladding damage in excess of pin hole leaks or hairline cracks, are authorized only if the total surface area of the damaged cladding does not exceed 5% of the total surface area of each rod.

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 4

OF 36 Table 1 NRU and NRX Mk I Fuel Specifications for Transport in the TN-LC-NRUX Basket Parameter NRU NRX Mk I

Physical and Material Description Number of Assemblies 26 26 Number of rods/assembly 12 7

Assembly length (inch) (1) 116 116 Nominal Assembly mass (g) 4660 5780 Fuel form U-Al U-Al 235U per rod (g) 45.4 75.2 Enrichment (wt.% 235U) 93 93 Cladding and Spacer Material Al Al Thermal and Radiological Parameters Cooling Time (years) (2) 10 10 Depletion (wt.% 235U) (3) 80 80 Decay Heat per Assembly (watts) (4) 15 15 Notes:

1.

Maximum length of the fuel assembly (unirradiated) for shipment.

2.

The cooling time of the fuel assembly rounded down to 0.5 years.

3.

The depletion (or burnup) of the fuel assembly rounded up to 0.5%.

4.

The decay heat of the fuel assembly is less than 15 watts at the maximum burnup and minimum cooling time.

(ii)

Intact or damaged MTR fuel elements that are enveloped or bounded by the fuel element design characteristics listed in Table 2 below, with an average burnup and minimum cooling time as specified in Table 3 below, and a maximum decay heat of 25 watts per element, are authorized for transportation in the TN-LC-MTR basket.

Intact fuel elements are fuel elements containing fuel plates with no known or suspected cladding defects greater than hairline cracks or pinhole leaks.

Damaged fuel elements, with cladding damage in excess of pin hole leaks or hairline cracks, are authorized only if the total surface area of the damaged cladding does not exceed 5% of the total surface area of each element.

The MTR fuel assemblies shall meet all the requirements in Table 3.

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 5

OF 36 Table 2 MTR Fuel Element Design Characteristics Fuel Element Class M-01 M-02 M-03 M-04 M-05 M-06 M-07 M-08(1)

Number of Fuel Plates (2) 23 21 19 17 10 18 17 23 235U mass per Plate (g) 16 16.5 17.5 19 22 20.5 11.5 22 Active Fuel Width (cm) 6.7 6.7 6.7 6.7 6.7 5.9 6.7 6.7 Active Fuel Length (cm) 56 56 56 56 56 56 27.5 56 Enrichment (wt.% 235U) 94 94 94 94 94 94 94 94 Fuel Element Depth (cm) 7.5 7.5 7.5 7.5 7.5 7.5 7.5

7.5 Notes

1. The M-08 Element class requires that the central stack of fuel elements remain empty. Also, the total 235U mass is limited by the maximum value in Table 3.

2. The plate thickness is greater than 0.12 cm and the clad thickness is greater than 0.02 cm.

Table 3 MTR Fuel Element Qualification Enrichment Type Burnup (MWd/MTU)

Cooling Time (days) 66,000 740 165,000 1120 330,000 1440 495,000 1680 Type A 235U Enrichment 90%

235U Mass 380 g 660,000 1950 57,750 770 144,375 1150 288,750 1470 433,125 1710 Type B 235U Enrichment 90%

380 g < 235U Mass 460 g 577,500 1950 29,330 740 73,325 1120 146,650 1440 219,975 1690 Type C 40% 235U Enrichment < 90%

235U Mass 380 g 293,300 1940 13,930 830 34,825 1220 69,650 1560 104,475 1850 Type D 19% 235U Enrichment < 40%

235U Mass 470 g 139,300 2150

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 6

OF 36 Notes Burnup = fuel element average burnup.

Use burnup (MWd/MTU) and Enrichment Type (A, B, C, or D with limits on 235U enrichment and 235U mass per element) to look up minimum cooling time in days.

Licensee is responsible for ensuring that uncertainties in burnup, enrichment, and mass are applied conservatively.

Fuel with burnups greater than those listed for each Enrichment Type is not authorized for transport.

Burnups may be either rounded up to the next higher burnup or linear interpolation may be used to determine the minimum cooling time. However, for conservatism, an additional cooling time of 30 days must be added to any linearly interpolated value.

Example: An M-06 class element with an enrichment of 45 wt.% 235U and a 235U mass of 350 grams is classified as enrichment Type C. A burnup of 100,000 MWd/MTU is acceptable for transport after 1440 days cooling time as defined by 146,650 MWd/MTU from the qualification table (when linear interpolation is not employed). When linear interpolation is employed the minimum required cooling time is 1267 days (1237 days based on interpolation + 30 days additional cooling time).

(iii)

Intact TRIGA fuel assemblies/elements that are enveloped by the fuel assemblies/element design characteristics listed in Table 4, intact TRIGA fuel follower control rods that are enveloped by the fuel assembly/element design characteristics listed in Table 5, with an average burnup and minimum cooling time meeting the specifications of Table 6 for fuel assemblies/elements or of Table 7 for follower control rods, and a maximum decay heat of 8 watts per assembly/element, are authorized for shipment with the TN-LC-TRIGA basket.

Intact fuel assemblies/elements are fuel assemblies/elements containing fuel rods with no known or suspected cladding defects greater than hairline cracks or pinhole leaks.

The design characteristics of the TRIGA fuel assemblies/elements are described in Tables 4 and 5 below.

The fuel qualification Tables 6 and 7 specify the maximum assembly/element average burnup and minimum cooling time. The fuel elements/assemblies shall meet all the requirements of Tables 6 and 7.

The poison plates in TN-LC-TRIGA basket are constructed from either boron aluminum alloy, or metal matrix composite (MMC), or Boral. The minimum areal density of Boron-10 (10B) for either the boron enriched aluminum alloy or the metal matrix composite is 5.56 mg/cm2. The minimum areal density of 10B for Boral is 6.67 mg/cm2.

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 7

OF 36 Table 5 TRIGA Fuel Follower Control Rods Design Characteristics Table 4 TRIGA Fuel Assembly/Element Design Characteristics Assembly/Element Type Al Clad ACPR (1)

Standard FLIP (2)

FLIP (2)

LEU-I (3)

FLIP( 2)

LEU-II (3)

Element ID T-01 T-02 T-03 T-04 T-05 T-06 Fuel Material U-ZrH U-ZrH U-ZrH U-ZrH U-ZrH U-ZrH Enrichment (wt.% 235U) 20 20 20 70 20 20 235U-Mass (g) 41 56 41 137 101 169 Active Fuel Length (inch) 15 15 15 15 15 15 Pellet Diameter (inch) 1.41 1.41 1.44 1.44 1.44 1.44 Clad Material Al SS304 SS304 SS304 SS304 SS304 H/Zr, max.

1.0 1.7 1.7 1.6 1.6 1.6 Assembly/Element Type Standard FLIP (2)

LEU-I (3)

ACPR (1)

Element ID T-07 T-08 T-09 Fuel Material U-ZrH U-ZrH U-ZrH Enrichment (wt. % 235U) 20 20 20 235U-Mass (g) 38 97 56 Active Fuel Length (inch) 15 15 15 Pellet Diameter (inch) 1.32 1.32 1.32 Clad Material SS304 SS304 SS304 H/Zr, max.

1.7 1.6

1.7 Notes

1.

ACPR - Annular Core Pulse Reactor 2.

FLIP - Fuel Life Improvement Program 3.

LEU - Low Enriched Uranium

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 8

OF 36 Table 6 TRIGA Fuel Qualification for Fuel Assembly/Elements Element ID Burnup (MWd/MTU)

Cooling Time (days) 35,750 400 71,500 560 107,250 640 T-01 143,000 710 35,750 650 71,500 970 107,250 1310 T-02 143,000 1870 35,750 520 71,500 840 107,250 1170 T-03 143,000 1730 112,500 1000 225,000 1380 337,500 1820 T-04 450,000 2520 35,750 920 71,500 1290 107,250 1710 T-05 143,000 2360 36,500 1190 73,000 1690 109,500 2320 T-06 146,000 3170

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 9

OF 36 Table 7 TRIGA Fuel Qualification for Fuel Follower Control Rods Element ID Burnup (MWd/MTU)

Cooling Time (days) 35,750 540 71,500 890 107,250 1280 T-07 143,000 1960 35,750 940 71,500 1350 107,250 1840 T-08 143,000 2580 35,750 670 71,500 1020 107,250 1420 T-09 143,000 2100 Notes for Tables 6 and 7:

Burnup = fuel element / assembly / follower control rod average burnup.

Use burnup (MWd/MTU) and Element ID to look-up minimum cooling time in days. Licensee is responsible for ensuring that uncertainties in burnup are applied conservatively.

Fuel with a burnup greater than that listed for each element type in Tables 6 and 7 is unacceptable for transport.

Burnups may be either rounded up to the next higher burnup or linear interpolation may be used to determine the minimum cooling time.

However, for conservatism, an additional cooling time of 30 days must be added to any linearly interpolated value.

Example: A T-03 element with a burnup of 100,000 MWd/MTU is acceptable for transport after 1170 days cooling time as defined by 107,250 MWd/MTU (Table 6, rounding up) on the qualification table (when linear interpolation is not employed). When linear interpolation is employed the minimum required cooling time is 1133 days (1103 days based on interpolation + 30 days additional cooling time).

(iv)

Intact or damaged PWR fuel assembly, as specified in Table 8, or intact BWR fuel assembly, as specified in Table 13, or intact or damaged fuel rods in a pin can are authorized for transport with the TN-LC-1FA basket.

Intact fuel assemblies are fuel assemblies containing fuel rods with no known or suspected cladding defects greater than hairline cracks or pinhole leaks.

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 10 OF 36 Damaged Fuel assemblies have missing or partial-length fuel rods or fuel rods with known or suspected cladding defects greater than hairline cracks or pinhole leaks.

The extent of cladding damage is to be limited such that it can be handled by normal means and that a fuel pellet is not able to pass through the gap created by the cladding opening. Damaged fuel assemblies can also contain top and bottom end fittings or nozzles or tie plates depending on the fuel type. Damaged PWR fuel assembly is authorized for transport only when confined in a Fuel Assembly Can (FAC).

Damaged Fuel rods are complete or partial-length fuel rods with known or suspected cladding defects greater than hairline cracks or pinhole leaks. The extent of cladding damage in the fuel rod is limited such that it can be handled by normal means and that a fuel pellet is not able to pass through the gap created by the cladding opening.

The fuel rods include irradiated PWR, BWR, MOX, and EPR fuel rods. Intact or damaged PWR and intact BWR fuel rods may be from any of the fuel assemblies listed in Table 8 or Table 13, respectively.

MOX rods have the same geometry as PWR or BWR rods, as defined in Table 8 and Table 13. The composition of MOX fuel is specified in Table 12.

The EPR fuel rods are specified in Table 10.

The poison plates in the TN-LC-1FA basket are constructed from boron aluminum alloy, or metal matrix composite (MMC), or Boral. The minimum 10B aeral density of the poison plate is 16.7 mg/cm2 for either the boron aluminum alloy or the MMC. The minimum 10B aeral density of the poison plate is 20.0 mg/cm2 for Boral.

In addition to the poison plates provided in the basket, Poison Rod Assemblies (PRAs) may be used for transportation of PWR fuel assemblies. The minimum required B4C content of the absorber rods in the PRA is 40% Theoretical Density (TD). A summary of the number of absorber rods required in the PRA for each PWR fuel class is shown in Table 11. PRA loading configurations are also illustrated in Figure 1 through Figure 5. Alternatively, in the absence of PRAs, burnup credit restrictions as shown in Table 11a and Table 11b are required for transportation of PWR fuel assemblies. Burnup credit is not applicable to BW 15x15 fuel class.

The PWR fuel assemblies fuel qualification table (FQT) is provided in Tables 15 and 15a. The BWR fuel assemblies FQT is provided in Table 16. The PWR rod FQTs are shown in Table 17 and Table 18 for the 21 and 9 rod configurations, respectively, and in Table 17a for the Unit 1 packaging. The BWR rod FQTs are shown in Table 19 and Table 20 for the 21 and 9 rod configurations, respectively. The MOX rod FQT, provided in Table 21 for both 21 and 9 rods, is applicable to both BWR and PWR MOX rods. The FQTs for the UO2 Standard EPR rods are governed by the PWR rod FQTs (Tables 17, 17a and 18), while the FQT for the MOX EPR rods is governed by the MOX rod FQT (Table 21).

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 11 OF 36 Table 8 WR Fuel Specifications for Transport in the TN-LC-1FA Basket Fuel Class (1) (2)

One intact or damaged unconsolidated B&W 17x17, WE 17x17, CE 16x16, B&W 15x15, WE 15x15, CE 15x15, WE 14x14, WE 16x16 or CE 14x14 class PWR assembly (without control components) that are enveloped by the fuel assembly design characteristics listed in Table 9. Reload fuel manufactured by the same or other vendors, but enveloped by the design characteristics listed in Table 9, is also acceptable.

Maximum Assembly + PRA +

damaged FAC Weight (as applicable) 1850 lbs. (839 kg)

Fissile Material UO2 Maximum Initial Uranium Content(4) 490 kg/assembly Maximum Unirradiated Assembly Length 178.3 inches (4528.8 mm)

Fuel Assembly Average Burnup, Enrichment and Minimum Cooling Time Per Tables 15 and 15a Maximum Planar Initial Enrichment 5.0(3) wt.% 235U Maximum Decay Heat(5) 3.0 kW per Assembly Minimum 10B areal density in poison plates

16.7 mg/cm2 (Natural or Enriched Boron Aluminum Alloy

/ Metal Matrix Composite (MMC))

20.0 mg/cm2 (Boral)

Minimum number of absorber rods per PRA as a function of assembly class Per Table 11 (Use of PRAs is optional except for BW 15x15)

Burnup credit Restrictions in the absence of PRAs Per Table 11a or 11b Notes:

1.

Up to 21 PWR fuel rods from any of the PWR fuel assemblies listed in Table 9 may also be transported in the TN-LC-1FA basket in a 21 pin can. The fuel rods are loaded in a 21 pin can with a cavity length of 169.55 inches (Option 3) which is placed within the TN-LC-1FA basket. The maximum peak burnup for the fuel rods is 90 GWd/MTU. The required cooling time, as a function of a PWR fuel rod burnup and enrichment, is provided in Table 17 or 17a for 21 rods and Table 18 for 9 rods, respectively.

2.

Up to 21 EPR fuel rods from any of the fuel class listed in Table 9 and meeting EPR rod parameters specified in Table 10 may also be loaded in the TN-LC-1FA basket. The fuel rods are loaded in a 21 pin can with a cavity length of 180.24 inches (Option 1 and Option 2) which is placed within the TN-LC-1FA basket. The maximum peak burnup for the fuel rods is 90 GWd/MTU. The required cooling time, as a function of an EPR fuel rod burnup and enrichment, is provided in Tables 17 or 17a for 21 rods and Table 18 for 9 rods, respectively.

3.

For CE 15x15, the maximum planar average initial enrichment is 3.60 wt.% 235U.

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 12 OF 36 4.

The maximum initial uranium content is based on the shielding analysis. The listed value is higher than the actual.

5.

The maximum decay heat per rod is 220 watts when loading up to 9 rods. The maximum decay heat per rod is 120 watts when loading 10 or more (up to 21) rods.

Table 9 PWR Fuel Assembly Design Characteristics for Transportation in the TN-LC-1FA Basket Assembly Class B&W 15x15 B&W 17x17 WE 17x17 CE 15x15 WE 15x15 CE 14x14 WE 14x14 CE 16x16 WE 16x16 Maximum Number of Fuel Rods 208 264 264 216 204 176 179 236 235 Maximum Number of Guide/Instrument Tubes 17 25 25 9

21 5

17 5

21 Rod Pitch(1) (inch) 0.568 0.502 0.496 0.550 0.563 0.580 0.556 0.506 0.496 Pellet Diameter(1) (inch) 0.374 0.323 0.323 0.360 0.367 0.382 0.368 0.326 0.323 Clad Outer Diameter(1)

(inch) 0.416 0.379 0.360 0.417 0.422 0.440 0.400 0.374 0.360 Clad Thickness(1) (inch) 0.024 0.024 0.022 0.026 0.024 0.026 0.022 0.023 0.022 Note 1. The fuel assembly fabrication documentation may be used to demonstrate compliance with these parameters which are design nominal values. Maximum and minimum dimensions are specified to bound variations in design nominal values among fuel assemblies within a fuel assembly class or an array type.

Table 10 Irradiated EPR Fuel Rod Parameters Parameter Value Maximum Unirradiated Length 179.5 inches Cladding Thickness Nominal 0.022 inch Maximum Initial Uranium Content 2.05 kgU/rod

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 13 OF 36 Table 11 Summary of PRA Requirements for PWR Fuel Assembly Classes Assembly Class Number of Absorber Rods in PRAs and Locations Diameter of B4C Absorber (cm)

Minimum B4C Content (g/cm)

WE 17x17 8, Per Figure 4 0.88 0.613 CE 16x16 5, All Guide Tubes 1.02 0.824 BW 15x15 8, Per Figure 3 0.88 0.613 CE 15x15 1, Center Guide Tube 0.76 0.475 WE 15x15 8, Per Figure 2 0.88 0.613 CE 14x14 5, All Guide Tubes 1.02 0.824 WE 14x14 /

WE 16x16 8, Per Figure 1 / 5 0.88 / 0.68 0.613 BW 17x17 8, Per Figure 4 0.76 0.475 Table 11a Maximum Planar Average Initial Enrichment/Minimum Burnup Combination - PWR Fuel Assembly Classes WE 17x17, WE 16x16, WE 15x15, CE 14x14, CE 15x15 and CE 16x16 Fuel Assembly Classes Fresh Fuel 2.90 wt. % U-235 Cooling Time 5 Years 10 Years 15 Years 20 Years Burnup (GWd/MTU)

Fuel Initial Enrichment (wt. % U-235) 5 3.04 3.05 3.06 3.08 10 3.37 3.40 3.42 3.44 15 3.66 3.70 3.74 3.76 20 4.43 4.53 4.61 4.65 25 4.87 5.00 5.00 5.00 WE 14x14 Fuel Assembly Class Fresh Fuel 2.95 wt. % U-235 Cooling Time 5 Years 10 Years 15 Years 20 Years Burnup (GWd/MTU)

Fuel Initial Enrichment (wt. % U-235) 5 3.26 3.26 3.27 3.28 10 3.65 3.65 3.66 3.68 15 3.92 3.96 4.00 4.03 20 4.67 4.80 4.86 4.93 25 5.00 5.00 5.00 5.00

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 14 OF 36 Table 11b Maximum Planar Average Initial Enrichment/Minimum Burnup Combination - PWR Fuel Assembly Classes - With Control Rod Insertion (1)

WE 17x17, WE 16x16, WE 15x15, CE 14x14, CE 15x15 and CE 16x16 Fuel Assembly Classes Fresh Fuel 2.90 wt. % U-235 Cooling Time 5 Years 10 Years 15 Years 20 Years Burnup (GWd/MTU)

Fuel Initial Enrichment (wt. % U-235) 5 2.97 2.99 3.00 3.01 10 3.29 3.31 3.34 3.36 15 3.54 3.60 3.64 3.66 20 4.21 4.38 4.45 4.53 25 4.75 4.91 4.98 5.00 30 5.00 5.00 5.00 WE 14x14 Fuel Assembly Class Fresh Fuel 2.95 wt. % U-235 Cooling Time 5 Years 10 Years 15 Years 20 Years Burnup (GWd/MTU)

Fuel Initial Enrichment (wt. % U-235) 5 3.20 3.20 3.21 3.23 10 3.57 3.57 3.59 3.59 15 3.81 3.86 3.90 3.90 20 4.48 4.62 4.71 4.78 25 5.00 5.00 5.00 5.00 (1) Fuel assemblies with accumulated control rod insertion through the first 15 GWd/MTU. Fuel assemblies with accumulated control rod insertion greater than the first MTU are not authorized.

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 15 OF 36 Table 12 MOX Fuel Rods Specifications for Transport in the TN-LC-1FA Basket PHYSICAL PARAMETERS:

Up to 21 PWR MOX fuel rods with physical parameters as those listed in Table 8.

Up to 21 BWR MOX fuel rods with physical parameters as those listed in Table 13.

Up to 21 EPR MOX fuel rods with physical parameters as those listed in Table 10.

Fissile Material UO2, PuO2 (Mixed Oxide or MOX)

Heavy Metal (HM) Content 2.5 kgU/rod CRITICALITY PARAMETERS:

Initial MOX composition

235U Content in UO2 :

0.5 235U 0.7 wt.%

Plutonium Content: Pu / (U + Pu) 7.0 wt.%

Initial 239Pu Content in PuO2 60.0 wt.%

Initial 241Pu Content in PuO2 7.5 wt.%

THERMAL/RADIOLOGICAL PARAMETERS:

Initial MOX Composition for Fuel Qualification

238Pu / 239Pu 4.0 wt.%

239Pu/ PuO2 50 wt.%

241Am / PuO2 70 ppm

235U/U 0.5 wt.%

Burnup and Minimum cooling time for MOX rods Per Table 21.

Maximum Decay heat per 25 pin can

2.5 kW for the pin can with up to 21 rods

1.8 kW for the pin can with up to 9 rods Minimum 10B aeral density in poison plates

16.7 mg/cm2 Boron Aluminum Alloy / Metal Matrix Composite (MMC)

20.0 mg/cm2 (Boral)

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 16 OF 36 Table 13 BWR Fuel Specification for Transport in the TN-LC-1FA Basket PHYSICAL PARAMETERS:

Fuel Class(1)

One intact 7x7, 8x8, 9x9, or 10x10 BWR assembly manufactured by General Electric or Exxon/ANF or FANP or ABB or reload fuel manufactured by same or other vendors that are enveloped by the fuel assembly design characteristics listed in Table 14.

Channels Fuel may be transported with or without channels, channel fasteners, or finger springs.

Fissile Material UO2 Maximum Assembly Weight with Channels 790 lbs Maximum Unirradiated Assembly Length 176.6 inches THERMAL/RADIOLOGICAL PARAMETERS:

Maximum Planar Average Initial Enrichment 5.0 wt.% 235U Fuel Assembly Average Burnup, Enrichment and Minimum Cooling Time Per Table 16.

Maximum Decay Heat(2) 2.0 kW per Assembly Minimum 10B aeral density in poison plates

16.7 mg/cm2 Boron Aluminum Alloy /

Metal Matrix Composite (MMC)

20.0 mg/cm2 (Boral)

Notes:

1. Up to 21 fuel rods from any of the BWR fuel assemblies listed in Table 14 may also be transported in the TN-LC-1FA basket in the 21 pin can. The fuel rods are loaded in a 21 pin can with a cavity length of 169.55 inches which is placed within the TN-LC-1FA basket. The required cooling time as a function of BWR fuel rod burnup and enrichment are provided in Table 19 for 21 rods and Table 20 for 9 rods, respectively.

2. The maximum decay heat per rod is 220 watts when loading up to 9 rods. The maximum decay heat per rod is 120 watts when loading 10 or more (up to 25) rods.

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 17 OF 36 Table 14 BWR Fuel Assembly Design Characteristics(1) for Transportation in the TN-LC-1FA Basket (Part 1 of 3)

Transnuclear ID 7x7-49/0 8x8-63/1 8x8-62/2 8x8-60/4 8x8-60/1 9x9-74/2 GE1 GE4 GE-5 GE8 Type II GE9 GE11 GE2 GE-Pres GE10 GE13 GE3 GE-Barrier GE8 Type I

Initial Design or Reload Fuel Designation FANP 8x8-2 Maximum Number of Fuel Rods 49 63 62 60 60 74 Maximum Initial Uranium Content (kg) 198 192 192 192 192 192 Rod Pitch(5) (inch) 0.738 0.640 0.640 0.640 0.640 0.566 Pellet Diameter(5)

(inch) 0.487 0.416 0.411 0.411 0.411 0.376 Clad Outer Diameter(5) (inch) 0.563 0.493 0.483 0.483 0.483 0.440 Clad Thickness(5)

(inch) 0.032 0.034 0.032 0.032 0.032 0.028 Table 14 BWR Fuel Assembly Design Characteristics(1) for Transportation in the TN-LC-1FA Basket (Part 2 of 3)

Transnuclear ID 10x10-92/2 7x7-49/0Z 7x7-48/1Z 8x8-60/4Z FANP 9x9 Siemens QFA GE12 ENC-IIIA ENC-III(2)

ENC Va FANP9 9x9(3) 9x9 Initial Design or Reload Fuel Designation GE14 ENC Vb Maximum Number of Fuel Rods 92 49 48 60 81 72 Maximum Initial Uranium Content (kg) 192 198 198 192 192 192 Rod Pitch(5) (inch) 0.510 0.738 0.738 0.642 0.572 0.570 Pellet Diameter(5) (inch) 0.345 0.488 0.491 0.420 0.357 0.374 Clad Outer Diameter(5)

(inch) 0.404 0.570 0.570 0.501 0.424 0.433 Clad Thickness(5) (inch) 0.026 0.035 0.035 0.036 0.030 0.026

5.(b)(1)

Type and Form of Materials (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 18 OF 36 Table 14 BWR Fuel Assembly Design Characteristics(1) for Transportation in the TN-LC-1FA Basket (Part 3 of 3)

Transnuclear ID 10x10-91/1 ABB-8x8 ABB-10x10 LaCrosse ATRIUM 10 SVEA-64 SVEA-100(4)

Allis Chalmers -

10x10 ATRIUM 10XM Exxon/ANF 10x10 Initial Design or Reload Fuel Designation Maximum Number of Fuel Rods 91 64 100 100 Maximum Initial Uranium Content (kg) 192 192 192 125 Rod Pitch(5) (inch) 0.510 0.622 0.512 0.565 Pellet Diameter(5) (inch) 0.350 0.411 0.346 0.350 Clad Outer Diameter(5)

(inch) 0.405 0.378 0.378 0.394 Clad Thickness(5) (inch) 0.023 0.024 0.022 0.020 Notes:

1.

Any fuel channel average thickness up to 0.120 inch is acceptable on any of the fuel designs.

2.

Includes ENC-IIIE and ENC-IIIF.

3.

Includes FANP 9x9-72, 9x9-79, 9x9-80, and 9x9-81.

4.

Includes SVEA-92, SVEA-96, SVEA-96+, SVEA-96 OPTIMA, SVEA-96 OPTIMA2, SVEA-96+/L.

5.

The fuel assembly fabrication documentation may be used to demonstrate compliance with these fuel assembly parameters. The fuel assembly parameters are design nominal values. The maximum and minimum dimensions are specified to bound variations in design nominal values among fuel assemblies within a fuel assembly class (or an array type).

(2)

Maximum quantity of material per package (i)

For the contents described in Item 5(b)(1)(i): 26 intact or damaged either NRU or NRX Mk I fuel assemblies, with an approximate maximum payload of 331 lb.

(ii)

For the contents described in Item 5(b)(1)(ii): 54 intact or damaged MTR fuel elements, with an approximate maximum payload of 1,620 lb.

(iii)

For the contents described in Item 5(b)(1)(iii): 180 intact TRIGA fuel elements/assemblies with an approximate maximum payload of 2,380 lb.

5.(b)(2)

Maximum quantity of material per package (continued)

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 19 OF 36 (iv)

For the contents described in Item 5(b)(1)(iv): one intact PWR fuel assembly, one damaged PWR fuel assembly confined in a FAC, or one intact BWR fuel assembly, or up to 21 intact or damaged PWR (including intact MOX and EPR) or intact BWR fuel rods in a pin can. When transporting 9 or fewer fuel rods, the rods shall be placed in the center 3x3 region of the pin can. The approximate maximum payload is 1,850 lb per PWR assembly with PRAs and Fuel Assembly Can (as applicable), 790 lb per BWR assembly with channels, and 16 lb per fuel rod.

(v)

For the Unit 1 packaging, contents described in Item 5(b)(1)(iv) are limited to: one intact PWR fuel assembly, one damaged PWR fuel assembly confined in a FAC, or up to 21 intact or damaged PWR (excluding intact MOX and EPR) fuel rods in a pin can. When transporting 9 or fewer fuel rods, the rods shall be placed in the center 3x3 region of the pin can. The approximate maximum payload is 1,850 lb per PWR assembly with PRAs and FAC as applicable, and 16 lb per fuel rod.

(3)

The maximum decay heat for any payload is 3.0 kW.

5(c)

Criticality Safety Index (CSI):

For NRU and NRX fuel assemblies described in 100 5(b)(1)(i) and limited in 5(b)(2)(i)

For MTR fuel elements described in 100 5(b)(1)(ii) and limited in 5(b)(2)(ii)

For TRIGA fuel assemblies/elements described in 0

5(b)(1)(iii) and limited in 5(b)(2)(iii)

For intact BWR fuel assemblies described in 0

5(b)(1)(iv) and limited in 5(b)(2)(iv)

For PWR fuel assemblies described in 100 5(b)(1)(iv) and limited in 5(b)(2)(iv) and 5(b)(2)(v)

For fuel rods in a 21 pin can described in 0

5(b)(1)(iv) and limited in 5(b)(2)(iv) and (5(b)(2)(v)

USA/9358/B(U)F-96 Page 20 of 36 Table 15 Fuel Qualification Table for a PWR Fuel Assembly (Minimum required years of cooling time after reactor core discharge)

Enrichment (wt. % 235U)

Burnup, GWd/

MTU 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 10 2.25 2.25 2.20 2.10 2.05 2.05 2.05 2.00 2.00 2.00 2.00 2.00 2.00 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.90 1.90 1.90 1.90 1.90 1.90 1.90 1.90 1.90 1.90 1.90 1.90 1.90 20 3.37 3.35 3.30 3.20 3.05 2.90 2.90 2.85 2.85 2.80 2.80 2.80 2.75 2.75 2.75 2.75 2.75 2.75 2.70 2.70 2.70 2.70 2.65 2.65 2.65 2.65 2.65 2.65 2.60 2.60 2.60 2.60 2.60 2.60 2.60 2.55 30 4.70 4.35 4.10 3.80 3.70 3.65 3.60 3.60 3.55 3.50 3.45 3.45 3.40 3.35 3.35 3.35 3.30 3.30 3.25 3.25 3.20 3.20 3.15 3.15 3.15 3.15 3.15 3.15 3.10 3.10 3.10 3.05 3.05 3.05 39 4.95 4.85 4.75 4.65 4.55 4.45 4.40 4.35 4.25 4.20 4.15 4.10 4.00 3.95 3.95 3.90 3.85 3.80 3.75 3.70 3.70 3.70 3.65 3.65 3.60 3.55 3.55 3.50 3.50 3.50 3.50 40 4.55 4.45 4.35 4.30 4.25 4.15 4.15 4.10 4.05 4.00 3.90 3.90 3.90 3.85 3.80 3.75 3.70 3.70 3.65 3.65 3.65 3.60 3.55 3.55 3.50 45 5.40 5.25 5.15 5.05 4.95 4.85 4.80 4.70 4.60 4.55 4.50 4.45 4.35 4.35 4.30 4.20 4.15 4.10 4.10 4.05 4.00 3.95 3.95 3.90 3.85 50 6.80 6.60 6.50 6.25 6.15 6.00 5.85 5.75 5.60 5.50 5.40 5.30 5.20 5.10 5.05 4.95 4.90 4.85 4.75 4.70 4.65 4.55 4.55 4.50 4.40 55 8.85 8.60 8.30 8.05 7.85 7.65 7.35 7.15 7.00 6.80 6.65 6.45 6.30 6.20 6.05 5.90 5.85 5.70 5.65 5.50 5.45 5.35 5.30 5.25 5.15 60 11.55 11.20 10.8510.50 10.15 9.80 9.55 9.20 8.95 8.70 8.45 8.25 8.00 7.80 7.55 7.40 7.20 7.05 6.85 6.75 6.60 6.45 6.35 6.25 6.10 61 12.15 11.80 11.4511.10 10.70 10.3510.10 9.75 9.45 9.20 8.90 8.65 8.35 8.20 7.90 7.75 7.55 7.40 7.20 7.00 6.85 6.75 6.55 6.50 6.40 62 12.80 12.40 12.0511.65 11.30 10.9010.65 10.25 9.95 9.70 9.40 9.10 8.85 8.55 8.35 8.15 7.90 7.70 7.50 7.30 7.20 7.05 6.85 6.75 6.65 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9

5.0 Notes

1.

Explanatory notes and limitations regarding the use of this table follow Table 21.

USA/9358/B(U)F-96 Page 21 of 36 Table 15a Fuel Qualification Table for a PWR Fuel Assembly - Unit 1 Packaging (Minimum required years of cooling time after reactor core discharge)

Enrichment, wt. % U-235 Burn-up, GWd/

MTU 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 10 3.0 3.0 2.9 2.9 2.8 2.8 2.8 2.8 2.7 2.7 2.7 2.7 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.4 2.4 2.4 2.4 2.4 20 4.7 4.6 4.5 4.4 4.3 4.2 4.2 4.1 4.0 4.0 3.9 3.9 3.8 3.8 3.8 3.7 3.7 3.6 3.6 3.6 3.6 3.5 3.5 3.5 3.5 3.4 3.4 3.4 3.4 3.4 3.4 3.3 3.3 3.3 3.3 3.3 30 6.7 6.5 6.3 6.2 6.0 5.9 5.7 5.6 5.5 5.3 5.2 5.1 5.1 5.0 4.9 4.8 4.7 4.7 4.6 4.6 4.5 4.5 4.4 4.4 4.3 4.3 4.2 4.2 4.2 4.1 4.1 4.1 4.1 4.0 39 7.1 6.9 6.7 6.6 6.4 6.3 6.2 6.0 5.9 5.8 5.7 5.6 5.5 5.4 5.4 5.3 5.2 5.2 5.1 5.0 5.0 4.9 4.9 4.8 4.8 4.8 4.7 4.7 4.6 4.6 4.6 40 6.4 6.2 6.1 6.0 5.9 5.8 5.7 5.6 5.5 5.4 5.4 5.3 5.2 5.2 5.1 5.1 5.0 5.0 4.9 4.9 4.8 4.8 4.7 4.7 4.7 50 9.6 9.4 9.2 8.9 8.7 8.5 8.3 8.1 7.9 7.8 7.6 7.5 7.3 7.2 7.1 6.9 6.8 6.7 6.6 6.5 6.4 6.3 6.2 6.2 6.1 12.

11.

11.

11.

10.

10.

10.

10.

55 0

7 4

1 8

5 3

0 9.8 9.6 9.4 9.1 8.9 8.8 8.6 8.4 8.2 8.1 7.9 7.8 7.7 7.5 7.4 7.3 7.2 14.

14.

14.

13.

13.

13.

12.

12.

12.

11.

11.

11.

11.

10.

10.

10.

10.

60 8

4 1

7 4

0 7

4 1

8 5

3 0

7 5

3 1

9.8 9.6 9.4 9.3 9.1 8.9 8.8 8.6 15.

15.

14.

14.

13.

13.

13.

12.

12.

12.

12.

11.

11.

11.

10.

10.

10.

10.

10.

61 4

0 7

3 9

6 3

9 6

3 0

7 5

2 9

7 5

2 0

9.8 9.6 9.4 9.3 9.1 8.9 16.

15.

15.

14.

14.

14.

13.

13.

13.

12.

12.

12.

11.

11.

11.

11.

10.

10.

10.

10.

10.

62 1

7 3

9 5

2 8

5 1

8 5

2 9

7 4

1 9

7 4

2 0

9.8 9.6 9.4 9.3 Enr. wt.%

0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 Note:

1.

Explanatory notes and limitations regarding the use of this table follow Table 21.

USA/9358/B(U)F-96 Page 22 of 36 Table 16 Fuel Qualification Table for a BWR Fuel Assembly (Minimum required years of cooling time after reactor core discharge)

Enrichment (wt. % 235U)

Burnup, GWd/

MTU 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 10 0.65 0.65 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 20 0.95 0.95 0.90 0.85 0.80 0.80 0.80 0.80 0.80 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 30 1.25 1.20 1.15 1.10 1.10 1.10 1.10 1.10 1.10 1.10 1.10 1.05 1.05 1.05 1.05 1.05 1.05 1.05 1.05 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 0.95 0.95 0.95 0.95 39 1.40 1.40 1.40 1.35 1.35 1.35 1.35 1.30 1.30 1.30 1.30 1.30 1.25 1.25 1.25 1.25 1.25 1.20 1.20 1.20 1.20 1.20 1.20 1.15 1.15 1.15 1.15 1.15 1.15 1.15 1.15 40 1.40 1.40 1.35 1.35 1.35 1.35 1.30 1.30 1.30 1.30 1.30 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.20 1.20 1.20 1.20 1.20 1.20 1.20 45 1.60 1.60 1.60 1.55 1.55 1.55 1.55 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.45 1.45 1.45 1.45 1.45 1.45 1.40 1.40 1.40 50 1.85 1.85 1.85 1.80 1.80 1.80 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.70 1.70 1.70 1.70 1.65 1.65 1.65 1.65 1.65 1.60 1.60 55 2.10 2.10 2.10 2.05 2.05 2.05 2.00 2.00 2.00 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.90 1.90 1.90 1.90 1.90 1.85 1.85 1.85 1.85 60 2.35 2.35 2.35 2.30 2.30 2.30 2.25 2.25 2.25 2.20 2.20 2.20 2.20 2.20 2.20 2.15 2.15 2.15 2.15 2.10 2.10 2.10 2.10 2.05 2.05 61 2.40 2.40 2.40 2.35 2.35 2.35 2.30 2.30 2.30 2.25 2.25 2.25 2.20 2.20 2.20 2.20 2.20 2.20 2.20 2.15 2.15 2.15 2.15 2.10 2.10 62 2.45 2.45 2.45 2.40 2.40 2.40 2.35 2.35 2.35 2.30 2.30 2.30 2.25 2.25 2.25 2.25 2.25 2.25 2.25 2.20 2.20 2.20 2.20 2.15 2.15 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9

5.0 Notes

1.

Explanatory notes and limitations regarding the use of this table follow Table 21.

USA/9358/B(U)F-96 Page 23 of 36 Table 17 Fuel Qualification Table for 21 PWR/EPR Fuel Rods (UO2)

(Minimum required years of cooling time after reactor core discharge)

Enrichment (wt. % 235U)

Burnup, GWd/

MTU 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 10 0.30 0.30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 20 0.30 0.30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 39 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 40 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 45 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 50 0.30 0.30 0.30 0.30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 55 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 60 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 61 0.40 0.40 0.40 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.30 0.30 62 0.40 0.40 0.40 0.40 0.40 0.40 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 65 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.35 0.35 0.35 0.35 0.35 0.35 70 0.50 0.50 0.50 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 75 0.65 0.65 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.50 0.50 0.50 0.50 80 0.85 0.85 0.75 0.75 0.75 0.75 0.75 0.70 0.70 0.70 0.70 0.70 0.70 0.70 85 1.05 1.00 1.00 1.00 0.90 0.90 0.90 0.90 0.85 0.85 0.85 0.85 0.85 0.85 90 1.25 1.25 1.25 1.15 1.15 1.15 1.10 1.10 1.10 1.00 1.00 1.00 1.00 0.95 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9

5.0 Notes

1.

Explanatory notes and limitations regarding the use of this table follow Table 21.

USA/9358/B(U)F-96 Page 24 of 36 Table 17a Fuel Qualification Table for 21 PWR Fuel Rods (UO2) - Unit 1 Packaging (Minimum required years of cooling time after reactor core discharge)

Enrichment, wt. % U-235 Burn-up, GWd/

MTU 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 10 0.35 0.35 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 20 0.35 0.35 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 30 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 39 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 40 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 45 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 50 0.35 0.35 0.35 0.35 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.300.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 55 0.37 0.37 0.37 0.36 0.36 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.350.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 60 0.50 0.49 0.48 0.47 0.47 0.46 0.45 0.45 0.44 0.44 0.43 0.43 0.42 0.42 0.410.41 0.41 0.40 0.40 0.40 0.39 0.39 0.39 0.38 0.38 61 0.53 0.52 0.51 0.5 0.5 0.49 0.48 0.47 0.47 0.46 0.46 0.45 0.44 0.44 0.440.43 0.43 0.42 0.42 0.42 0.41 0.41 0.41 0.40 0.40 62 0.56 0.55 0.54 0.53 0.53 0.52 0.51 0.5 0.49 0.49 0.48 0.48 0.47 0.46 0.460.45 0.45 0.44 0.44 0.44 0.43 0.43 0.43 0.42 0.42 65 0.560.55 0.55 0.540.53 0.53 0.52 0.51 0.51 0.50 0.50 0.49 0.49 0.49 70 0.710.70 0.69 0.680.67 0.67 0.66 0.65 0.65 0.64 0.63 0.62 0.62 0.61 75 0.870.86 0.85 0.840.83 0.82 0.8 0.79 0.79 0.78 0.77 0.76 0.75 0.75 80 1.041.03 1.01 1.000.99 0.97 0.96 0.95 0.94 0.93 0.92 0.91 0.90 0.89 85 1.241.22 1.20 1.181.16 1.15 1.13 1.12 1.10 1.09 1.08 1.06 1.05 1.04 90 1.471.44 1.41 1.391.37 1.34 1.32 1.3 1.29 1.27 1.25 1.23 1.22 1.20 Enr. wt.%

0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 Note1. Explanatory notes and limitations regarding the use of this table follow Table 21.

USA/9358/B(U)F-96 Page 25 of 36 Table 18 Fuel Qualification Table for 9 PWR/EPR Fuel Rods (UO2)

(Minimum required years of cooling time after reactor core discharge)

Enrichment (wt. % 235U)

Burnup, GWd/

MTU 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 10 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 20 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 39 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 40 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 45 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 50 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 55 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 60 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 61 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 62 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 65 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 70 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 75 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 80 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 85 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 90 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9

5.0 Notes

1.

Explanatory notes and limitations regarding the use of this table follow Table 21.

USA/9358/B(U)F-96 Page 26 of 36 Table 19 Fuel Qualification Table for 21 BWR Fuel Rods (UO2)

(Minimum required years of cooling time after reactor core discharge)

Enrichment (wt. % 235U)

Burnup, GWd/

MTU 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 10 0.30 0.30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 20 0.30 0.30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 39 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 40 0.40 0.40 0.40 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 45 0.45 0.45 0.45 0.45 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 50 0.60 0.60 0.60 0.60 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.50 0.50 0.50 0.50 0.50 0.50 0.50 55 0.75 0.75 0.75 0.75 0.75 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 60 1.00 1.00 1.00 1.00 0.90 0.90 0.90 0.90 0.90 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 61 1.05 1.05 1.00 1.00 1.00 1.00 1.00 0.90 0.90 0.90 0.90 0.90 0.90 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.75 0.75 0.75 0.75 62 1.10 1.05 1.05 1.05 1.05 1.00 1.00 1.00 1.00 1.00 0.90 0.90 0.90 0.90 0.90 0.90 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 65 1.05 1.05 1.00 1.00 1.00 1.00 1.00 1.00 1.00 0.90 0.90 0.90 0.90 0.90 70 1.20 1.20 1.20 1.15 1.15 1.15 1.15 1.15 1.15 1.10 1.10 1.10 1.10 1.10 75 1.45 1.45 1.45 1.40 1.40 1.40 1.30 1.30 1.30 1.30 1.25 1.25 1.25 1.25 80 1.70 1.70 1.65 1.65 1.60 1.60 1.60 1.50 1.50 1.50 1.45 1.45 1.45 1.45 85 2.15 2.05 2.00 2.00 1.95 1.85 1.85 1.80 1.80 1.70 1.70 1.65 1.65 1.65 90 2.60 2.55 2.50 2.40 2.35 2.30 2.20 2.15 2.15 2.10 2.00 2.00 1.95 1.95 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 Notes:

1. Explanatory notes and limitations regarding the use of this table follow Table 21.

USA/9358/B(U)F-96 Page 27 of 36 Table 20 Fuel Qualification Table for 9 BWR Fuel Rods (UO2)

(Minimum required years of cooling time after reactor core discharge)

Enrichment (wt. % 235U)

Burnup, GWd/

MTU 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 10 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 20 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 39 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 40 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 45 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 50 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 55 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 60 0.30 0.30 0.30 0.30 0.30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 61 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.25 0.25 0.25 62 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 65 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 70 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 75 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 80 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 85 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 90 0.60 0.60 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.7 0.8 0.9 1.2 1.5 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9

5.0 Notes

1.

Explanatory notes and limitations regarding the use of this table follow Table 21.

USA/9358/B(U)F-96 Page 28 of 36 Notes:

Table 21 Fuel Qualification Table for MOX PWR/BWR/EPR 21 Rods and MOX PWR/BWR/EPR 9 Rods 9 Rods 25 Rods Burnup, GWd/MTHM 0.5 wt.% of 235U 0.7 wt.% of 235U 0.5 wt.% of 235U 0.7 wt.% of 235U 10 0.25 0.25 0.25 0.25 20 0.25 0.25 0.30 0.30 30 0.25 0.25 0.50 0.50 40 0.25 0.25 0.95 0.95 45 0.25 0.25 1.25 1.25 50 0.35 0.35 1.70 1.70 55 0.40 0.40 2.20 2.10 60 0.45 0.45 2.80 2.70 62 0.55 0.55 3.75 3.65 1.

Explanatory notes and limitation regarding the use of this table are provided on the following page.

USA/9358/B(U)F-96 Page 29 of 36 Notes:

General 1.

Use burnup and enrichment to look up minimum cooling time in years. Licensee is responsible for ensuring that uncertainties in fuel enrichment and burnup are correctly accounted for during fuel qualification.

2.

For values not explicitly listed in the tables, round burnups up to the first value shown, round enrichments down, and select the cooling time listed.

3.

UO2 Fuel with an initial enrichment less than 0.7 (or less than the minimum provided above for each burnup) or greater than 5.0 wt.% 235U is unacceptable for transportation.

4.

Shaded areas in these Tables indicate fuel is not analyzed for loading.

For Fuel Assemblies 1.

Burnup = Assembly Average burnup.

2.

Enrichment = Assembly Average Enrichment.

3.

Fuel assembly with a burnup greater than 62 GWd/MTU is unacceptable for transportation.

For Fuel Rods 4.

Burnup = Maximum burnup.

5.

Enrichment = Rod Average Enrichment.

6.

When transporting 21 or less fuel rods, the rods shall be placed in a specially designed pin can.

7.

When transporting 9 or less fuel rods, the rods shall be placed in the 3x3 region of the pin can.

8.

Fuel rods with a burnup greater than 90 GWd/MTU are unacceptable for transportation.

Example: Per Table 15, a PWR assembly with an initial enrichment of 4.85 wt.% 235U and a burnup of 41.5 GWd/MTU is acceptable for transport after a 3.95-year cooling time as defined by 4.8 wt.% 235U (rounding down) and 45 GWd/MTU (rounding up) on the qualification table (other considerations not withstanding).

USA/9358/B(U)F-96 Page 30 of 36 Poison Rod Locations Empty Guide Tube Locations Note: This configuration indicates the relative location of the poison rods within the guide tubes and does not provide any other fuel class specific information. Any other configuration of poison rods that is rotationally symmetric is also acceptable.

Figure 1 PRA Insertion Locations for WE 14x14 Class Assemblies

USA/9358/B(U)F-96 Page 31 of 36 Poison Rod Locations Empty Guide Tube Locations Note: This configuration indicates the relative location of the poison rods within the guide tubes and does not provide any other fuel class specific information. Any other configuration of poison rods that is rotationally symmetric is also acceptable.

Figure 2 PRA Insertion Locations for WE 15x15 Class Assemblies

USA/9358/B(U)F-96 Page 32 of 36 Poison Rod Locations Empty Guide Tube Locations Note: This configuration indicates the relative location of the poison rods within the guide tubes and does not provide any other fuel class specific information. Any other configuration of poison rods that is rotationally symmetric is also acceptable.

Figure 3 PRA Insertion Locations for BW 15x15 Class Assemblies

USA/9358/B(U)F-96 Page 33 of 36 Poison Rod Locations Empty Guide Tube Locations Note: This configuration indicates the relative location of the poison rods within the guide tubes and does not provide any other fuel class specific information. Any other configuration of poison rods that is rotationally symmetric is also acceptable.

Figure 4 PRA Insertion Locations for BW 17x17 and WE 17x17 Class Assemblies

USA/9358/B(U)F-96 Page 34 of 36 Note:

This configuration indicates the relative location of the poison rods within the guide tubes and does not provide any other fuel class specific information. Any other configuration of poison rods that is rotationally symmetric is also acceptable.

Figure 5 PRA Insertion Locations for WE 16x16 Class Assemblies

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 35 OF 36 6.

In addition to the requirements of Subpart G of 10 CFR Part 71:

(a)

The package must be prepared for shipment and operated in accordance with the Operating Procedures of Chapter No. 7 of the application, and (b)

Each packaging must meet the Acceptance Tests and Maintenance Program of Chapter No.

8 of the application.

7.

Transport by air of fissile material is not authorized.

8.

Prior to the first shipment, the package shall be tested for the entire containment boundary, e.g., all base metal, all joining containment welds, vent port plug seal, drain port plug seal, lid seal, and bottom plug seal, in accordance with ANSI N14.5-2014, by helium leakage rate testing to meet the leaktight criteria of 1.0x10-7 ref-cm3/sec for fabrication leakage tests.

9.

Poison Rod Assemblies, required for shipment of PWR assemblies if burnup credit is not considered, shall be installed such that the active fuel length is covered by the absorber, and measures shall be taken against their inadvertent removal from the fuel assembly.

10.

The package authorized by this certificate is hereby approved for use under the general license provisions of 10 CFR 71.17.

11.

Revision No. 6 of this certificate may be used until June 30, 2023.

12.

Expiration date: May 31, 2027.

NRC FORM 618 U.S. NUCLEAR REGULATORY COMMISSION (8-2000) 10 CFR 71 CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES 1.

a. CERTIFICATE NUMBER 9358

b. REVISION NUMBER 7

c. DOCKET NUMBER 71-9358

d. PACKAGE IDENTIFICATION NUMBER USA/9358/B(U)F-96 PAGE PAGES 36 OF 36 REFERENCES TN-LC Transportation Package Safety Analysis Report, Revision No. 10, dated April 2022.

Renewal Request letter dated March 22, 2022.

FOR THE U.S. NUCLEAR REGULATORY COMMISSION Date See digital signature Name:

W. Allen, Acting Chief Storage and Transportation Licensing Branch Division of Fuel Management Office of Nuclear Material Safety and Safeguards Signed by Allen, William on 06/23/22