ML20248G094
| ML20248G094 | |
| Person / Time | |
|---|---|
| Site: | Comanche Peak  |
| Issue date: | 08/21/1989 |
| From: | TEXAS UTILITIES ELECTRIC CO. (TU ELECTRIC) |
| To: | |
| Shared Package | |
| ML20248B228 | List: |
| References | |
| PROC-890821-01, NUDOCS 8910100072 | |
| Download: ML20248G094 (2) | |
Text
(_
T Z -:. ' g.[.s$ '
.?
~
,- { M }-[ _ v CPSES-INSERVICE TESTIFs PROGRAM PLAN s
- REVIS!Ott 3 '
IPA S 64"
.i
- RELIEF REQUEST NtBSER:
16.6 1
4 SYSTENs Chemical and Volume Control i
VALVE NUBSER:
1CS-8350A,B,C,D 1CS-8367A,B,C,D CATEGORY:
C CLASS 1
FUNCTION:
' Reactor Coolant Pump Seal Injection Flow Path TEST REQUIREMENT:.
Eseroise valve to the position required to fulfill its function at least onoe' every ?
- months, BASIS FOR RELIEF:
. Power Operation and Cold Shutdowns - These series check valves provide the ASA boundary' between Class 1 RCS and Class 2 CVCS as required by ANSI N18.2a. These valves are not leak.
tested, are not high/ low pressure system interfaces and are not listed as RCS pressure isolation valves in Technical Specification Table 3.4-1.
These valves perform their safety 1 function in the closed position therefore partial stoking is not applicable. Full stroke' eneroising during power operation would require securing seal injaction flow to the remotor coolant pumps. The interruption of this flow would result in equa.gunent damage. Performing.
testing during cold shutdown would require contain= ant entry, plant manipulation and test equigunent set up.
Due to the similar function of these valves, the conditions observed during the Alternate Testing of one valve will be representative of the others.
Hardships resulting frra AIARA concerns and the use of manpower and resources which could be otherwise dedicated to more critical safety related work would not be acumpensated for by an increased level of quality or safety.
ALTERNATE TESTING:
Verify operability of the valves by partially disassembling, manually exercising and visually inspecting the internals of two of the valves at each refueling outage on an alternating schedule. If either of these valves are found to be inoperable then the other valves will be disassembled and inspected before any of the valves will be declared -
eperable.
i, 8910100072 890922 PDR ADOCK 05000445 PDR 4
APPENDIX A 1
7 1
1
" th _,,,
ist..
nyi f.g', i t v
.j:,
v
- fCfsES-INSERVICK TESTIp PROGRAM PLAN..
'l.
.LEVISION 3 1
g 4
'-- FAW 64 e 3
RELIEF REQtEST NMER 16.6
H
-f Chemical ' nd Va' imme Control NYSTEN:-
a
- VALVE NUseER:
1Cs-8350A,B,C,D 1C8-8367A,B,C,D
/
4 CATEGOEra'
.C e.
CLhSS '
' 1~
FUNCTION:
Reactor Coolant Pump Seal Injection Flow Path
+-
TEST REQUIREMENT:
Esercise valve to the position required to fulfill its function at least once every 3 months.
BA8IS FOR RELIEFsf Power operation and Cold shutdowns - These series check valves provida the ABS boundary between Class 1 RCS and Class 2 CVCS as required by ANSI N18.2a. These valves are not leak.
tested, are not high/ low pressure system interfaces and are not listed as RCS pressure.
isolation valves in Technical specification Table 3.4-1.
These valves perform their safety.
function in the closed position therefore partial stoking is not applicable. Full stroke k
eseroising during power aparation would require securing seal injection flow to the remotor ooolant pumps. The interruption of this flow would result in equigenent damage. Performing testing during cold shutdown would require con +a h nt entry, plant manipulation and tsat equigenent set up.
Due to the similar function of these valves, the conditions observed during the Alternate Testing of one valve will be representative of the others.
Hardships resulting frca AIARA concerns and the use of manpower and resources which could be otherwise dedicated to more critical safety related work would not be caspensated for by s
an increased level of quality or safety.
ALTERNATE TESTING Verify operability of the valves by partially disassembling, manually azorcising and' visually inspecting the internals of two of the valves at each refueling ontage on an alternating schedule. If either of these valves are found to be inoperable then the other valves will be disassembled and inspected before any of the valves will be declared operable.
APPENDIX A
..