ML20116G691
| ML20116G691 | |
| Person / Time | |
|---|---|
| Site: | FitzPatrick  |
| Issue date: | 07/31/1996 |
| From: | POWER AUTHORITY OF THE STATE OF NEW YORK (NEW YORK |
| To: | |
| References | |
| NUDOCS 9608080263 | |
| Download: ML20116G691 (30) | |
Text
!
NEW YORK POWER AUTHORITY JAMES A. FITZPATRICK NUCLEAR POWER PLANT DOCUMENT TRANSMITTAL AND RECEIPT FORM i
TO:
NRC Region 1 Administrator i
l FROM:
Janet Kerfien - Tech Services i
i UNCONTROLLED l
COPY NO.
Information Only i
l DATE:
August 2.1996 PROCEDURE REVISION i
CORE OPERATING LIMITS REPORT 4
i l
I Please update your uncontrolled manual!
Thanks, Janet G APPLICABLE MANUAL:
CORE OPERATING LIMITS REPORT i
l l
INSTRUCTIONS:
- 1. Insert the attached revised documents into your uncontrolled manual.
)
- 2. Sign below signifying that you have received the subject uncontrolled documents and have i
inserted them into the applicable uncontrolled manual.
1 l
- 3. Return all superseded documents, as applicable, with this signed form to the sender within i
14 days.
\\
NOTE Failure to incorporate these documents into your uncontrolled manual and return of this form will result in cancellation of the subject uncontrolled l
documents.
SIGNATURE DATE i
9608080263 960731 PDR ADOCK 05000333 PDR p
l l
L \\ COMO _10 0
00?Y NEW YORK POWER AUTHORITY JAMES A.
FITZPATRICK NUCLEAR POWER PLANT REPORT CORE OPERATING LIMITS REPORT REVISION 4 REVIEWED BY:
PLANT OPERATIONS REVIEW COMMITTEE MEETING NO. kh 'h DATE 7"/7 h
/
7 f~kh APPROVED BY:
DATE REACTO AI.lfST SUPERVISOR APPROVED BY:
L DATE 7
/G PLANT MA)TAGER I
I
/
/
O Rev. No. 4 Page 1 of 29
I cQOKE OPERATING LIMITS REPORT CYCLE 12 1.0 PURPOSE l
This report provides the cycle-specific operating limits for Cycle 12 of the James A.
FitzPatrick Nuclear Power Plant.
The following limits are addressed:
l l
Operating Limit Minimum Critical Power Ratio (MCPR) l Flow Dependent MCPR Limits l
Maximum Average Planar Linear Heat Generation Rate (MAPLHGR)
Linear Heat Generation Rate (LHGR)
Flow-Biased Average Power Range Monitor
(. PRM) and Rod A
Block Monitor (RBM) Settings 2.0 APPLICABILITY The plant shall be operated within the limits specified in this report.
If any of these limits are violated, the corrective actions specified in the Technical Specifications shall be taken.
3.0 REFERENCES
i 3.1 JAFNPP Administrative Procedure 12.05, Control of Core Operating Limits Report.
3.2 JAFNPP License Appendix A, Operating Technical Specifications.
3.3 FitzPatrick Cycle 12 Core Reload Safety Evaluation, JAF-SE-94-127.
3.4 JAFNPP SAFER /GESTR-LOCA Loss of Coolant Analysis, NEDE-31317P, including Errata and Addenda Sheets 1, 2 and 3.
3.5 Supplemental Reload Licensing Submittal for JAFNPP Reload 11 Cycle 12, GE Report 24A5167 Revision 0 June 1996.
Includes a Supplement 1 containing MAPLHGR DATA.
3.6 Supplement 1 to GE Report 23A7114 June,1992.
Contains MAPLHGR Data for Reload 10 Fuel.
3.7 Cycle 12 Core Reload, M1-94-164.
l l
3.8 RAP-7.3.17 Rev.6, Core Monitoring Software and Databsae l
l Changes.
3.9 PLANT OPERATION UP TO 100% POWER WITH ONE STEAM LINE ISOLATED, JAF-SE-96-035.
Rev. No. 4 Page 2 of 29
, CORE OPERATING LIMITS REPORT CYCLE 12
'n 4.0 DEFINITIONS 4.1 Minimum critical power ratio (MCPR) - Minimum value of the ratio of that power in a fuel assembly which is calculated i
to cause some point in that fuel assembly to experience boiling transition to the actual assembly operating power as calculated by application of the GEXL correlation (Reference NEDE-10958).
4.2 Fraction of Limiting Power Density - The ratio of the linear heat generation rate (LHGR) existing at a given location to l
the design LHGR.
The design LHGR is given in Table 8.2.
4.3 Maximum Fraction of Limiting Power Density - The Maximum Fraction of Limiting Power Density (MFLPD) is the highest value existing in the core of the Fraction of Limiting Power Density (FLPD).
4.4 Rated Recirculation Flow - that drive flow which produces a core flow of 77.0 x 106 lb/hr.
5.0 RESPONSIBILITIES 5.1 See AP-12.05 (Reference 3.1).
,3
(\\ ')
5.2 It is the responsibility of the Shift Manager to assure that l
the reactor is operated within the limits described herein.
5.3 It is the responsibility of the Reactor Analyst Supervisor to assure that the limits described herein are properly installed in the 3D-Monicore databank used for thermal limit surveillance (Reference 3.8) 6.0 SPECIAL INSTRUCTIONS /REOUIREMENTS Not applicable.
O Rev. No. 4 Page 3 of 29
, CORE OPERATING LIMITS REPORT CYCLE 12 7.0 PROCEDURE 7.1 Operating Limit MCPR During power operation, The Operating Limit MCPR shall be equal to or greater than the limits given below.
7.1.1-Technical Specification
Reference:
3.1.B 1
7.1.2 The Operating Limit MCPR shall be determined based on i
the following requirement:
7.1.2.1 The average scram time to notch position 38 shall be:
7 AVE 5 IB 7.1.2.2 The average scram time to notch position 38 is determined as follows:
1 j
~
EEYT II
= i=1 T
jgg g
- IUV, i=1 where:
1 n=
number of surveillance tests performed to date in the cycle, N; =
number of active rods measured in the ith surveillance, and ri =
average scram time to notch position 38 of all rods measured in the ith surveillance test.
O Rev.'No. 4 Page 4 of 29 y-
, CORE OPERATING LIMITS REPORT CYCLE 12
()
7.l.2.3 The adjusted analysis mean scram time is calculated as follows:
N*
t, (sec) = p + 1.65 a ENg
,l-1 where:
p=
mean of the distribution for the average scram insertion time to the pickup of notch position 38 - 0.706 sec.
o=
standard deviation of the distribution for average scram insertion time to the pickup of notch position 38 = 0.016 sec.
N the total number of active rods
=
measured in Technical Specification 4.3.C.1.
The number of rods to be scram tested and the test intervals are given in Technical Specification 4.3.C.
7.1.3 When requirement of 7.1.2 is met, the Operating Limit MCPR shall not be less than that specified in Table 8.1, or Table 8.1.A if operating above 75% of rated thermal power with three steam lines in service.
f~T U
Rev. No. 4 Page 5 of 29
I l.
CORE OPERATING LIMITS REPORT CYCLE 12 l
[)
7.1.4 When the requirement 7.1.2 is not met (i.e. 7 a<7 AVE) then the Operating Limit MCPR values (as a function of 7) are given in Figure 8.1, or Figure 8.1.A if operating above 75% of j
rated thermal power with three steam lines in service.
( 7 ys - Ts) / ( 7
- Ts) where 7
=
3 3
and the average scram time to notch position 38 7 AVE
=
as defined in 7.1.2.2.
the adjusted analysis mean scram time as 7,
=
defined in 7.1.2.3 the scram time to notch position 38 as 7
=
3 defined in Technical Specification 3.3.C.1.
Note:
Should the operating limit MCPR obtained from these figures be less than the operating limit MCPR found in 7.1.3 for the applicable RBM trip level setting then 7.1.3 shall apply.
[~/
)
7.1.5 During single-loop operation, the Operating Limit
\\
MCPR shall be increased by 0.01.
7.1.6 During reactor power operation with core flow less than 100 percent of rated, the Operating Limit MCPR shall be multiplied by the appropriate Kr specified in Figure 8.2.
7.2 Maximum Average Planar Linear Heat Generation Rate (MAPLHGR) 7.2.1 Technical Specification
Reference:
3.5.H 7.2.2 During power operation, the APLHGR for each fuel type as a function of axial location and average planar exposure shall be within limits based on applicable APLHGR limit values which have been approved for the respective fuel and lattice l
types.
7.2.3 When hand calculations are required, the APLHGR for each type of fuel as a function of average l
planar exposure shall not exceed the limiting value for the most limiting lattice (excluding natural uranium) shown in Figures 8.3.a through h.
("%
7.2.4 During single loop operation, the APLHGR for each
\\,)
fuel type shall not exceed the values given in
(
7.2.2 or 7.2.3 above multiplied by 0.84.
Rev. No. 4 Page 6 of 29
, CORE OPERATING LIMITS REPORT CYCLE 12
/~'
's,)\\
i 7.3 Linear Heat Generation Rate (LHGR) 7.3.1 Technical Specification
Reference:
3.5.I.
7.3.2 The LHGR of any rod in any fuel assembly at any axial location shall not exceed the maximum allowable LHGR specified in Table 8.2.
7.4 APRM Trip Settings 7.4.1 APRM Flow Referenced Flux Scram Trip Setting (Run Mode) 7.4.1.1 Technical Specification
References:
2.1.A.1.c, Table 3.1-1, 3.1.A 7.4.1.2 When the Mode Switch is in the RUN position, the APRM flow referenced flux scram trip setting shall be Ss0.66W + 54% for two loop operation; Ss0.66W + 54% - 0.66 AW for single loop operation; O
where:
U setting in percent of rated thermal S
=
power (2436 MWt);
recirculation flow in percent of rated; W
=
AW difference between two loop and
=
single-loop effective drive flow at the same core flow.
G(\\
Rev. No. 4 Page 7 of 29
,COghOPERATINGLIMITSREPORT CYCLE 12
()
7.4.1.3 In the event of operation with a maximum fraction of limiting power density (MFLPD) greater than the fraction of rated power (FRP), the setting shall be modified as follows:
Ss(0.66W + 54%) (FRP/MFLPD) for two loop operation; Ss(0.66W + 54% - 0.66 AW) (FRP/MFLPD) for single-loop operation; where:
fraction of rated thermal power FRP
=
(2436 Mwt) ;
MFLPD =
Maximum fraction of limiting power density, where the limiting power density is as specified in Table 8.2.
The ratio of FRP to MFLPD shall be set equal to 1.0 unless the actual operating value is less than the design value of 1.0, in which case the actual operating value will be used.
O.
7.4.2 APRM Flow Biased Rod Block Setting 7.4.2.1 Technical Specification
References:
2.1.A.1.d, Table 3.2-3, 3.2.C 7.4.2.2 The APRM rod block trip setting shall be:
Ss0.66W + 42% for two loop operation; Ss0.66W + 42% - 0.66 AW for single loop operation; where:
S = rod block setting in percent of rated thermal power (2436 Mwt) ;
recirculation flow in percent of cated; W
=
AW =
difference between two loop and single loop effective drive flow at the same core flow.
O Rev. No. 4 Page 8 of 29
, CORE OPERATING LIMITS REPORT CYCLE 12
()
7.4.2.3 In the event of operation with a maximum
~
fraction of-limiting power density (MFLPD) greater than the fraction of rated power (FRP), the setting shall be modified as follows:
Ss(0.66W + 42%) (FRP/MFLPD) for two loop operation; Ss (0. 66W + 42% - 0. 66AW) (FRP/MFLPD) for single loop operation;.
where:
fraction of rated thermal power FRP
=
(2436 Mwt) ;
MFLPD =
maximum fraction of limiting power density as specified in Table 8.2.
7.5 RBM Flow Biased Rod Block Setting 7.5.1 Technical Specification
Reference:
3.2.C 7.5.2 The-RBM flow biased rod block trip setting shall be:
Ss0.66W + K for two loop operation; Ss0.66W + K - 0.66AW for single loop operation; where:
S = rod block setting in percent of initial; W = loop flow in percent of rated K = intercept values of 39%,-40%, 41%, 42%, 43%,
and 44% can be used with the appropriate MCPR Operating Limit from Table 8.1(note that for Cycle 12 the RBM intercept value does not effect the MCPR Operating Limit for K values s 44%);
AW = difference between two loop and single loop effective drive flow.
O Rev. No. 4 Page 9 of 29
,_CORb OPERATING LIMITS REPORT CYCLE 12 8.0 FIGURES AND TABLES Table 8.1
-MCPR Operating Limit for Incremental Cycle Core Average Exposure Table 8.1.A MCPR Operating Limit for Incremental Cycle Core Average Exposure for Operation above 75%
of Rated Thermal Power with Three Steam Lines in Service
{
Table 8.2 Maximum LHGR l
Figure 8.1 MCPR Operating Limit Versus 7 Figure 8.1.A MCPR Operating Limit Versus 7 for Operation 1
above 75% of Rated Thermal Power with Three Steam Lines in Service Figure 8.2 Kr Factor Figure 8.3.a MAPLHGR Versus Planar Average Exposure:
BD336A Figure 8.3.b MAPLHGR Versus Planar Average Exposure:
BD339A Figure 8.3.c MAPLHGR Versus Planar Average Exposure:
GE10-P8HXB322-11GZ-70M-150-T Figure 8.3.d MAPLHGR Versus Planar Average Exposure:
GE10-P8HXB324-12GZ-70M-150T Figure 8.3.e MAPLHGR Versus Planar Average Exposure:
89LTA l
Figure 8.3.f MAPLHGR Versus Planar Average Exposure:
GE11-P9 HUB 356-15GZ-100M-146T and ATRIUM-10A Figure 8.3.g MAPLHGR Versus Planar Average Exposure:
GE11-P9 HUB 359-16GZ1-100M-146-T Figure 8.3.h MAPLHGR Versus Planar Average Exposure:
GE11-P9 HUB 380-12GZ5-100M-146-T Figure 8.4.a CYCLE 12 LOADING PATTERN, UPPER LEFT QUADRANT, BUNDLE DESIGN Figure 8.4.b CYCLE 12 LOADING PATTERN, UPPER RIGHT QUADRANT, BUNDLE DESIGN Figure 8.4.c CYCLE 12 LOADING PATTERN, LOWER RIGHT O
QUADRANT, BUNDLE DESIGN Rev. No. 4 Page 10 of 29
,CO8b OPERATING LIMITS REPORT CYCLE 12 Figure 8.4.d CYCLE 12 LOADING PATTERN, LOWER LEFT QUADRANT, BUNDLE DESIGN 9.0 EXHIBITS Not Applicable.
(
O G
Rev. No. 4 page 11 of 29
QORE, OPERATING LIMITS REPORT CYCLE 12
- ()
TABLE 8.1 MCPR Operating Limit for Incremental Cycle Core Average Exposure 4
Cycle 12 GE11-P9 HUB 380-All Other Fuel Exposure 12GZ5-100M-146-T Bundle Types i
Range I
BOC 1.36 1.31 to 4 GWD/ST
>4 GWD/ST 1.31 1.31 to 9 GWD/ST
>9 GWD/ST 1.32 1.32 to 10.5 GWD/ST
~
>10.5 GWD/ST 1.35 1.35
/3 to EOC L.)
Technical Specification
Reference:
3.1.B For single loop operation, these limits shall be increased by 0.01.
j l
O Rev. No. 4 Page 12 of 29
,,, CORE OPERATING LIMITS REPORT CYCLE 12 TABLE 8.1.A MCPR Operating Limit for Incremental Cycle Core Average Exposure for Operation above 75% of Rated Thermal Pcwer with Three Steam Lines in Service Cycle 12 GE11-P9 HUB 380-All Other Fuel Exposure 12GZ5-100M-146-T Bundle Types Range BOC 1.36 1.31 to 4 GWD/ST
>4 GWD/ST 1.31 1.31 to 9 GWD/ST
>9 GWD/ST 1.34 1.34 to 10.5 GWD/ST
>10.5 GWD/ST 1.37 1.37 to EOC l
Technical Specification
Reference:
3.1.B For single loop operation, these limits shall be increased by 0.01.
O Rev. No. 4 Page 13 of 29
,COR5 OPERATING LIMITS REPORT CYCLE 12 O
TABLE 8.2 Maximum LHGR Fuel Type Fuel Bundle Design Maximum LHGR (kw/ft)
BD336A GE8x8EB 14.4 BD339A GE8x8EB 14.4 GE10-P8HXB322 GE8x8NB-3 14.4 l
11GZ-70M-150-T GE10-P8HXB324 GE8x8NB-3 14.4 12GZ-70M-150-T 1
89LTA GE11LTA 14.4 GE11-P9 HUB 356 Gell 14.4 15GZ-100M-146-T GE11-P9 HUB 359 Gell 14.4 16GZ1-100M-146-T O
GE11-P9 HUB 380 Gell 14.4 12GZ5-100M-146-T Technical Specification
Reference:
3.5.1 1
O i
Rev. No.'4 Page 14 of'29
,COI}E OPERATING LIMITS REPORT CYCLE 12 i
FIGURE 8.1 MCPR Operating Limit Versus 7 (TAU) i i
1.46 1.46 1.45 1.45 1.44 1.44 1.43 1.43 1.42 1.42 1.41 1.41 2 1.4 1.4 'S 1.39
- 1.39{
1.30 1.38 C 1.37
- 1.37[
1.36 1.363 1.35
- 1.35y 1.34 1.34 1.33 1.33
/
1.32 1.32 1.31 1.31
- 1. 9 1 9 1.28 1.28 1.27 1.27 1.26 1.26 0
1 I
Tau C BOC to 9 GWDIST
+
>9 to 10.5 GWDl5T o
>10.5 GtDIST to FOC Technical Specification
Reference:
3.1.B For single loop operation, these limits shall be increased by 0.01.
Note:
Should the operating limit MCPR obtained from this
~'
figure be less than the operating limit MCPR found in 7.1.3 for the applicable RBM trip level setting then 7.1.3 shall apply.
Rev. No. 4 Page 15 of 29
I l
,, CORE OPERATING LIMITS REPORT CYCLE 12 l
FIGURE 8.1.A MCPR Operating Limit Versus 7 (TAU)
For Operation above 75% of Rated Thermal Power with Three Steam Lines in Service i
1.46 1,46 1.45 1.45 1.44 1.44 1.43 1,43 1.42 1.42 1.41 1.412 1.4
- 1.4 5
\\
~
1.39 1.39 -
1.30 1.38 C 1.37 1.37 E l
1.36 1.36 ~
j 1.35 1.35y j
1.34 1.34
[
1.33 1.33 1.32 1,32 j
1.31 1.31 1.3 1.3 1.29 1,29 1
1.28 1.28 1.27 1.27 1.26 1.26 0
1 Tau O 80C to 9 GWDIST
+
>9 to 10.5 GWDIST o
>10.5 GWDIST to EOC i
Technical Specification
Reference:
3.1.B For single loop operation, these limits shall be increased by 0.01.
Og Note:
Should the operating limit MCPR obtained from this V
figure be less than the operating limit MCPR found in 7.1.3 for the applicable RBM trip level setting then 7.1.3 shall apply.
Rev. No. 4 Page 16 of 29
,,COPyE OPERATING LIMITS REPORT CYCLE 12 i
FIGURE 8.2 l
Kr Factor
}
1.4 i
j 1
sa 4
i i
l i
I Kr j
u j
autoimre n ow co m a sl1 i
i 1
esasan nawcowina scoopwar armans CmamariON MGfT100s0D suas mar nownian - iss.n i
a sous iisas i,
i 117.05 l
4 i
j a,
i n
i e
a n
30 40 to 80 70 90 30 100 COfE FLOW lt)
Technical Specification
Reference:
3.1.B 4
- O Rev. No. 4 Page 17 of 29
. =.
l
,, CORE OPERATING LIMITS REPORT CYCLE 12 1
O FIGURE 8.3.a MAPLHGR Versus Planar Average Exposure:
BD336A l
14.08 13.88 12.11 11,88 10.00 1.18 1.80 7.81 6,00 5.88 4.88 i
I 3.08 2.81 1.88
)
1,13 i
8 18 21 30 40 50 la Pleser Average EssesurelGWDit) l l
This curve represents the limiting j.
exposure dependent MAPLHGR values.
l l
Technical Specification
Reference:
3.5.H
Reference:
For single loop operating these MAPLHGR values shall be multiplied by 0.84.
l
?U l
l l
l l
Rev. No. 4 Page 18 of 29 i
,,COKS OPERATING LIMITS REPORT CYCLE 12 FIGURE 8.3.b (y
MAPLHGR Versus Planar Average Exposure:
BD339A 14.00
- 2. B 11.88 18.88
\\
I 88 1.88 7.18 8.81 5.88 4.88 3.00 2.00 1.80 t
I 18 II 48 58 il Pleser Averste EstesuretGWDit]
This curve represents the limiting l
exposure dependent MAPLHGR values.
Technical Specification
Reference:
3.5.H
Reference:
NEDC-31317P For single loop operating these MAPLHGR values shall be multiplied by 0.84.
O Rev. No. 4 Page 19 of 29 1
, CORE OPERATING LIMITS REPORT CYCLE 12 FIGURE 8.3.c MAPLHGR Versus Planar Average Exposure:
GE10-P8HXB322-11GZ-70M-150-T 14.80 13.80 12.88 11.88 18.00 8.00 8.10 1.80 E.IB 5.81 4.00 3.00 2.00
/"N b
a 10 28 31 45 50 El l
Planer Averste EsposarelGwDit)
This curve represents the limiting exposure dependent MAPLHGR values.
Technical Specification
Reference:
3.5.H
Reference:
NEDC-31317P For single loop operating these MPi...GR values cliall be multiplied by 0.84.
l l
4' [
}
\\
%./
t I
Rev, No. 4 Page 20 of 29
,, CORE OPERATING LIMITS REPORT CYCLE 12
.r'N
)
FIGURE 8.3.d
~
MAPLHGR Versus Planar Average Exposure:
GE10-P8HXB324-12GZ-70M-150T 14.00 13.00 12.80 11.18 10.80 S.81 I.00 7.88 E.80 5.18 4.00 3.lQ 2.18 v) 1.88
'l 18 20 la 46 58 18 Pleper Average EstesoretGWDit!
This curve represents the limiting exposure dependent MAPLHGR values.
Technical Specification
Reference:
3.5.H
Reference:
NEDC-31317P For single loop operating these MAPLHGR values shall be multiplied by 0.84.
l 1
N Rev. Nc. 4 Page 21 of 29
1
,, CORE OPERATING LIM 1TS REPORT CYCLE 12 l
f^
's")
FIGURE 8.3.e MAPLHGR Versus Planar Average Exposure:
89LTA 13.11 12.18 11.00 10.18 3.81 8.88 1.81 I.Il 3.00 4.88 3.18 1
2.00 l.80
.)
0.11 i
8 11 21 31 40 58 la Pisesr Averege Espesure[GWDit)
This curve represents the limiting exposure dependent MAPLHGR values.
Technical Specification
Reference:
3.5.H
Reference:
NEDC-31317P For single loop operating these MAPLHGR values shall be multiplied by 0.84.
n
(
i
't.)
Rev. No. 4 Page 22 of 29 1
l
,, CORE OPERATING LIMITS REPORT CYCLE 12 FIGURE 8.3.f l A.)
MAPLHGR Versus Planar Average Exposure:
GE11-P9 HUB 356-15GZ-100M-146-T and ATRIUM-10A*
l 1
12.81 11.88 18.80 3.00 1.80 7.88 5.08 5.00 4.80 1
3.00 2.81 l\\
f.88 l
l B.00 I
18 28 18 48 58 El l
l Piseer Aversee EspesaretGvGit]
i l
l
- The A10-339 bundle will be monitored as a GE11-P9 HUB 356-15GZ-100M-146-T bundle.
Operation to the limiting MAPLHGR l
for the Gell bundle assures this bundle will remain within l
LHGR limits, see Reference 3.8.
i i
l This curve represents the limiting exposure dependent MAPLHGR values.
Technical Specification
Reference:
3.5.H
Reference:
A23A7114 Rev 1 For single loop operating these MAPLHGR values shall be
{O g
multiplied by-0.84.
Rev. No. 4 Page 23 of 29
,,COfEOPERATINGLIMITSREPORT CYCLE 12 1
FIGURE 8.3.g Y
MAPLHGR Versus Planar Average Exposure:
GE11-P9 HUB 359-16GZ1-100M-146-T 12.80 11.80 18.1B 1.00 1.80 7.00 5.18 4
5.18 4.88 3.00 2.80
.[
\\
1,81 i
i i
i i
B 18 28 38 48 56 II I
i Planer Average Espessrs (GfDl5T)
This curve represents the limiting exposure dependent MAPLHGR values.
Technical Specification
Reference:
3.5.H
Reference:
23A7114 Rev 1 l
For ningle loop operating these MAPLHGR values shall be
)
multiplied by 0.84.
r^
.tU Rev. No. 4 Page 24 of 29
,, CORE OPERATING LIMITS REPORT CYCLE 12 rhh FIGURE 8.3.h MAPLHGR Versus Planar Average Exposure:
GE11-P9 HUB 380-12GZ5-100M-146-T 4
1 14 13 i
12 11 18 R
8 7
8 5
4 3
2
/^N t
i 1
V 8
l t's I
6 I
so 18 II 58 Piener Averste EspesarelGfDit)
This curve represents the limiting exposure dependent MAPLHGR values.
Technical Specification
Reference:
3.5.H
Reference:
24A5167 Rev 0 For single loop operating these MAPLHGR values shall be multiplied by 0.84.
OQU Rev. No. 4 Page 25 of 29
,, CORE OPERATING LIMITS REPORT CYCLE 12 O
1 1
2 1
1 52 l
1 2
4 5
5-5 50 1
2 1
1 4
5 4
5 2
48 i
1 2
4 5
5 5
4 5
2 5
46 1
2 6
5 4
5 4
2 2
4 4
44-2 4
5 4
5 2
2 4
5 4
4 42 2
5 4
5 2
4 4
5 4
5 2
40 1
1 5-5 2
4 3
5 4
4 2
5 38 i
1 2
4 5
4 2
4 5
4 4
2 5
2 36 2
4 5
4 2
4 5
4 4
4-4 4
4 34 i
i l
2 5
4 5
2 5
4 4
2 4
2 4
2 32 1
5 5
2 4
4 5
2 5
4 4
2 4
30 1
5 2
5 4
4 2
5 2
4 2
4 4
28 I
l 01 03 05 07 09 11 13 15 17 19 21 23 25 l
FIGURE 8.4.a I
CYCLE.12 LOADING PATTERN, UPPER LEFT QUADRANT, BUNDLE DESIGN i
1 = GE8x8EB, Bundle Types BD319A, BD336A, BD339A l
2 = GE8x8NB-3, Bundle Types P8HXB322, P8HXB324 l
3 = GE11LTA, Bundle Type 89LTA 4 = Gell, Bundle Type P9 HUB 356, P9 HUB 359 5=
Gell, Bundle Type P9 HUB 380 6 = ATRIUM-10A, Bundle Type A10-339 1
i i
Rev. No. 4 Page 26 of 29 i
i CORE OPERATING LIMITS REPORT CYCLE 12 0
52 2
1 2
1 1
:===
50 5
5 5
4 2
1 48 2
5 4
5 4
2 2
2 1
4 46 5
2 5
4 5
5 5
4 2
1 i
44 4
4 2
2 4
5 4
5 6
1 1
42 4
4 5
4 2
2 5
4 5
4 2
40 2
5 4
5 4
4 2
5 4
5 2
_.r 38 5
2 4
4 5
3 4
2 5
5 2
1 36 2
5 2
4 4
5 4
2 4
5 4
2 1
34 4
4 4
4 4
4 5
4 2
4 5
4 1
32 2
4 2
4 2
4 1
5 2
5 4
5 2
30 1
2 4
4 5
2 5
4 4
2 5
5 1
28 4
4 2
4 2
5 2
4 4
5 2
5 1
27 29 31 33 35 37 39 41 43 45 47 49 51 FIGURE 8.4.b CYCLE 12 LOADING PATTERN, UPPER RIGHT QUADRANT, BUNDLE DESIGN 1 = GE8x8EB, Bundle Types BD319A, BD336A, BD339A 2 = GE8x8NB-3, Bundle Types P8HXB322, P8HXB324 3 = GE11LTA, Bundle Type 89LTA j
4 = Gell, Bundle Type P9 HUB 356, P9 HUB 359 i
5=
Gell, Bundle Type P9 HUB 380 6 = ATRIUM-10A, Bundle Type A10-339 f%
\\
l Rev. No. 4 Page 27 of 29
....e CORE OPERATING LIMITS REPORT CYCLE 12 0
27 29 31~
33 35 37 39 41 43 45 47 49 51 26 4
4 2
4 2
5 2
4 4
5 2
5 2
24 4
2 4
4 5
2 5
4 4
2 5
5 1
22 2
4 2
4 2
4 4
5 2
5 4
5 2
20 4
4 4
4 4
4 5
4 2
4 5
4 2
l I
18 2
5 2-4 4
5 4
2 4
5 4
2 1
16 5
2 4
4 5
3 4
2 5
5 1
1 14 2
5 4
5 4
4 2
5 4
5 1
12 4
'4 5
4 2
2 5
4 5
4 2
10 4
4 2
2 4
5 4
5 6
2 1
I 08 5
2 5
4 5
5 5
4 2
1 06 2
5 4
5 4
2 2
2 1
04 5
5 5
4 2
1 02 1
1 2
2 1
FIGURE 8.4.c CYCLE.12 LOADING PATTERN, LOWER RIGHT QUADRANT, BUNDLE DESIGN 1 = GE8x8EB, Bundle Types BD319A, BD336A, BD339A 2 = GE8x8NB-3, Bundle Types P8HXB322, P8HXB324 4
3 = GE11LTA, Bundle Type 89LTA 4 = Gell, Bundle Type P9 HUB 356, P9 HUB 359 5=
Gell, Bundle Type P9 HUB 380 1
6 = ATRIUM-10A, Bundle Type A10-339 O
Rev. No. 4 Page 28 of 29
...,e CORE OPERATING LIMITS REPORT CYCLE 12 l
Ol' 03 05 07 09 11 13 15 17 19 21 23 25 1
5 2
5 4
4 2
5 2
4 2
4 4
26 1
1 5
'5 2
4 4
5 2
5 4
4 2
4 24 2
5 4
5 2
5 4
4 2
4 2
4 2
22 1
4 5
4 2
4 5
4 4
4 4
4 4
20 I
1 1
2 4
5 4
2 4
5 4
4 2
5 2
18 1
1 5
5 2
4 3
5 4
4 2
5 16 I
2 5
4 5
2 4
4 5
4 5
2 14 2
4 5
4 5
2 2
4 5
4 4
12 1
1 6
5 4
5 4
2 2-4 4
10 1
1 4
5 5
5 4
5 2
5 08 1
2 1
2 4
5 4
5 2
06 1
2 4
5 5
5 04 1
2 2
1 1
02 1
FIGURE 8.4.d CYCLE 12 LOADING PATTERN, LOWER LEFT QUADRANT, BUNDLE DESIGN 1 = GE8x8EB, Bundle Types BD319A, BD336A, BD339A 2 = GE8x8NB-3, Bundle Types P8HXB322, P8HXB324 l
3 = GE11LTA, Bundle Type 89LTA l
4 = Gell, Bundle Type P9 HUB 356, P9 HUB 359 5=
Gell, Bundle Type P9 HUB 380 I
6 = ATRIUM-10A, Bundle, Type A10-339 i
1 O
4 Rev. No. 4 Page 29 of 29
, _ _. -.._